diff options
author | Thomas Gleixner <tglx@linutronix.de> | 2009-05-20 09:02:28 +0200 |
---|---|---|
committer | Thomas Gleixner <tglx@linutronix.de> | 2009-05-20 09:02:28 +0200 |
commit | 521c180874dae86f675d23c4eade4dba8b1f2cc8 (patch) | |
tree | 7509303da3a9a1b40a26f6811f321c89cd31737b /Documentation/blockdev/mflash.txt | |
parent | f1a11e0576c7a73d759d05d776692b2b2d37172b (diff) | |
parent | 64d1304a64477629cb16b75491a77bafe6f86963 (diff) |
Merge branch 'core/urgent' into core/futexes
Merge reason: this branch was on an pre -rc1 base, merge it up to -rc6+
to get the latest upstream fixes.
Conflicts:
kernel/futex.c
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Diffstat (limited to 'Documentation/blockdev/mflash.txt')
-rw-r--r-- | Documentation/blockdev/mflash.txt | 84 |
1 files changed, 84 insertions, 0 deletions
diff --git a/Documentation/blockdev/mflash.txt b/Documentation/blockdev/mflash.txt new file mode 100644 index 00000000000..1f610ecf698 --- /dev/null +++ b/Documentation/blockdev/mflash.txt @@ -0,0 +1,84 @@ +This document describes m[g]flash support in linux. + +Contents + 1. Overview + 2. Reserved area configuration + 3. Example of mflash platform driver registration + +1. Overview + +Mflash and gflash are embedded flash drive. The only difference is mflash is +MCP(Multi Chip Package) device. These two device operate exactly same way. +So the rest mflash repersents mflash and gflash altogether. + +Internally, mflash has nand flash and other hardware logics and supports +2 different operation (ATA, IO) modes. ATA mode doesn't need any new +driver and currently works well under standard IDE subsystem. Actually it's +one chip SSD. IO mode is ATA-like custom mode for the host that doesn't have +IDE interface. + +Followings are brief descriptions about IO mode. +A. IO mode based on ATA protocol and uses some custom command. (read confirm, +write confirm) +B. IO mode uses SRAM bus interface. +C. IO mode supports 4kB boot area, so host can boot from mflash. + +2. Reserved area configuration +If host boot from mflash, usually needs raw area for boot loader image. All of +the mflash's block device operation will be taken this value as start offset. +Note that boot loader's size of reserved area and kernel configuration value +must be same. + +3. Example of mflash platform driver registration +Working mflash is very straight forward. Adding platform device stuff to board +configuration file is all. Here is some pseudo example. + +static struct mg_drv_data mflash_drv_data = { + /* If you want to polling driver set to 1 */ + .use_polling = 0, + /* device attribution */ + .dev_attr = MG_BOOT_DEV +}; + +static struct resource mg_mflash_rsc[] = { + /* Base address of mflash */ + [0] = { + .start = 0x08000000, + .end = 0x08000000 + SZ_64K - 1, + .flags = IORESOURCE_MEM + }, + /* mflash interrupt pin */ + [1] = { + .start = IRQ_GPIO(84), + .end = IRQ_GPIO(84), + .flags = IORESOURCE_IRQ + }, + /* mflash reset pin */ + [2] = { + .start = 43, + .end = 43, + .name = MG_RST_PIN, + .flags = IORESOURCE_IO + }, + /* mflash reset-out pin + * If you use mflash as storage device (i.e. other than MG_BOOT_DEV), + * should assign this */ + [3] = { + .start = 51, + .end = 51, + .name = MG_RSTOUT_PIN, + .flags = IORESOURCE_IO + } +}; + +static struct platform_device mflash_dev = { + .name = MG_DEV_NAME, + .id = -1, + .dev = { + .platform_data = &mflash_drv_data, + }, + .num_resources = ARRAY_SIZE(mg_mflash_rsc), + .resource = mg_mflash_rsc +}; + +platform_device_register(&mflash_dev); |