MIPS: Alchemy: new userspace suspend interface for development boards.

Replace the current sysctl-based suspend interface with a new sysfs-
based one which also uses the Linux-2.6 suspend model.

To configure wakeup sources, a subtree for the demoboards is created
under /sys/power/db1x:

sys/
`-- power
    `-- db1x
        |-- gpio0
        |-- gpio1
        |-- gpio2
        |-- gpio3
        |-- gpio4
        |-- gpio5
        |-- gpio6
        |-- gpio7
        |-- timer
        |-- timer_timeout
        |-- wakemsk
        `-- wakesrc

The nodes 'gpio[0-7]' and 'timer' configure the GPIO0..7 and M2
bits of the SYS_WAKEMSK (wakeup source enable) register.  Writing '1'
enables a wakesource, 0 disables it.

The 'timer_timeout' node holds the timeout in seconds after which the
TOYMATCH2 event should wake the system.

The 'wakesrc' node holds the SYS_WAKESRC register after wakeup (in hex),
the 'wakemsk' node can be used to get/set the wakeup mask directly.

For example, to have the timer wake the system after 10 seconds of sleep,
the following must be done in userspace:

echo 10 > /sys/power/db1x/timer_timeout
echo 1 > /sys/power/db1x/timer
echo mem > /sys/power/sleep

This patch also removes the homebrew CPU frequency switching code.  I don't
understand how it could have ever worked reliably; it does not communicate
the clock changes to peripheral devices other than uarts.

Signed-off-by: Manuel Lauss <mano@roarinelk.homelinux.net>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

 create mode 100644 arch/mips/alchemy/devboards/pm.c

2 files changed, 0 insertions, 353 deletions

diff --git a/arch/mips/alchemy/common/irq.c b/arch/mips/alchemy/common/irq.c
index c54384779fb..c88c821b4c3 100644
--- a/arch/mips/alchemy/common/irq.c
+++ b/arch/mips/alchemy/common/irq.c
@@ -37,8 +37,6 @@
 #include <asm/mach-pb1x00/pb1000.h>
 #endif
 
-static DEFINE_SPINLOCK(irq_lock);
-
 static int au1x_ic_settype(unsigned int irq, unsigned int flow_type);
 
 /* per-processor fixed function irqs */
@@ -611,45 +609,3 @@ void __init arch_init_irq(void)
 
 	set_c0_status(IE_IRQ0 | IE_IRQ1 | IE_IRQ2 | IE_IRQ3);
 }
-
-unsigned long save_local_and_disable(int controller)
-{
-	int i;
-	unsigned long flags, mask;
-
-	spin_lock_irqsave(&irq_lock, flags);
-	if (controller) {
-		mask = au_readl(IC1_MASKSET);
-		for (i = 0; i < 32; i++)
-			au1x_ic1_mask(i + AU1000_INTC1_INT_BASE);
-	} else {
-		mask = au_readl(IC0_MASKSET);
-		for (i = 0; i < 32; i++)
-			au1x_ic0_mask(i + AU1000_INTC0_INT_BASE);
-	}
-	spin_unlock_irqrestore(&irq_lock, flags);
-
-	return mask;
-}
-
-void restore_local_and_enable(int controller, unsigned long mask)
-{
-	int i;
-	unsigned long flags, new_mask;
-
-	spin_lock_irqsave(&irq_lock, flags);
-	for (i = 0; i < 32; i++)
-		if (mask & (1 << i)) {
-			if (controller)
-				au1x_ic1_unmask(i + AU1000_INTC1_INT_BASE);
-			else
-				au1x_ic0_unmask(i + AU1000_INTC0_INT_BASE);
-		}
-
-	if (controller)
-		new_mask = au_readl(IC1_MASKSET);
-	else
-		new_mask = au_readl(IC0_MASKSET);
-
-	spin_unlock_irqrestore(&irq_lock, flags);
-}
diff --git a/arch/mips/alchemy/common/power.c b/arch/mips/alchemy/common/power.c
index f58e151b38d..6ab7b42aa1b 100644
--- a/arch/mips/alchemy/common/power.c
+++ b/arch/mips/alchemy/common/power.c
@@ -42,18 +42,6 @@
 
 #ifdef CONFIG_PM
 
-#define DEBUG 1
-#ifdef	DEBUG
-#define DPRINTK(fmt, args...)	printk(KERN_DEBUG "%s: " fmt, __func__, ## args)
-#else
-#define DPRINTK(fmt, args...)
-#endif
-
-extern unsigned long save_local_and_disable(int controller);
-extern void restore_local_and_enable(int controller, unsigned long mask);
-
-static DEFINE_SPINLOCK(pm_lock);
-
 /*
  * We need to save/restore a bunch of core registers that are
  * either volatile or reset to some state across a processor sleep.
@@ -74,21 +62,6 @@ static unsigned int sleep_sys_clocks[5];
 static unsigned int sleep_sys_pinfunc;
 static unsigned int sleep_static_memctlr[4][3];
 
-/*
- * Define this to cause the value you write to /proc/sys/pm/sleep to
- * set the TOY timer for the amount of time you want to sleep.
- * This is done mainly for testing, but may be useful in other cases.
- * The value is number of 32KHz ticks to sleep.
- */
-#define SLEEP_TEST_TIMEOUT 1
-#ifdef	SLEEP_TEST_TIMEOUT
-static int sleep_ticks;
-static void wakeup_counter0_set(int ticks)
-{
-	au_writel(au_readl(SYS_TOYREAD) + ticks, SYS_TOYMATCH2);
-	au_sync();
-}
-#endif
 
 static void save_core_regs(void)
 {
@@ -234,13 +207,6 @@ static void restore_core_regs(void)
 #endif
 }
 
-unsigned long suspend_mode;
-
-void wakeup_from_suspend(void)
-{
-	suspend_mode = 0;
-}
-
 void au_sleep(void)
 {
 	save_core_regs();
@@ -248,279 +214,4 @@ void au_sleep(void)
 	restore_core_regs();
 }
 
-static int pm_do_sleep(ctl_table *ctl, int write, struct file *file,
-		       void __user *buffer, size_t *len, loff_t *ppos)
-{
-	unsigned long wakeup, flags;
-	int ret;
-#ifdef SLEEP_TEST_TIMEOUT
-#define TMPBUFLEN2 16
-	char buf[TMPBUFLEN2], *p;
-#endif
-
-	spin_lock_irqsave(&pm_lock, flags);
-
-	if (!write) {
-		*len = 0;
-		ret = 0;
-		goto out_unlock;
-	};
-
-#ifdef SLEEP_TEST_TIMEOUT
-	if (*len > TMPBUFLEN2 - 1) {
-		ret = -EFAULT;
-		goto out_unlock;
-	}
-	if (copy_from_user(buf, buffer, *len)) {
-		return -EFAULT;
-		goto out_unlock;
-	}
-	buf[*len] = 0;
-	p = buf;
-	sleep_ticks = simple_strtoul(p, &p, 0);
-	wakeup_counter0_set(sleep_ticks);
-#endif
-
-	/**
-	 ** The code below is all system dependent and we should probably
-	 ** have a function call out of here to set this up.  You need
-	 ** to configure the GPIO or timer interrupts that will bring
-	 ** you out of sleep.
-	 ** For testing, the TOY counter wakeup is useful.
-	 **/
-#if 0
-	au_writel(au_readl(SYS_PINSTATERD) & ~(1 << 11), SYS_PINSTATERD);
-
-	/* GPIO 6 can cause a wake up event */
-	wakeup = au_readl(SYS_WAKEMSK);
-	wakeup &= ~(1 << 8);	/* turn off match20 wakeup */
-	wakeup |= 1 << 6;	/* turn on  GPIO  6 wakeup */
-#else
-	/* For testing, allow match20 to wake us up. */
-	wakeup = 1 << 8;	/* turn on match20 wakeup   */
-	wakeup = 0;
-#endif
-	au_writel(1, SYS_WAKESRC);	/* clear cause */
-	au_sync();
-	au_writel(wakeup, SYS_WAKEMSK);
-	au_sync();
-
-	au_sleep();
-	ret = 0;
-
-out_unlock:
-	spin_unlock_irqrestore(&pm_lock, flags);
-	return ret;
-}
-
-#if !defined(CONFIG_SOC_AU1200) && !defined(CONFIG_SOC_AU1550)
-
-/*
- * This is right out of init/main.c
- */
-
-/*
- * This is the number of bits of precision for the loops_per_jiffy.
- * Each bit takes on average 1.5/HZ seconds.  This (like the original)
- * is a little better than 1%.
- */
-#define LPS_PREC 8
-
-static void au1000_calibrate_delay(void)
-{
-	unsigned long ticks, loopbit;
-	int lps_precision = LPS_PREC;
-
-	loops_per_jiffy = 1 << 12;
-
-	while (loops_per_jiffy <<= 1) {
-		/* Wait for "start of" clock tick */
-		ticks = jiffies;
-		while (ticks == jiffies)
-			/* nothing */ ;
-		/* Go ... */
-		ticks = jiffies;
-		__delay(loops_per_jiffy);
-		ticks = jiffies - ticks;
-		if (ticks)
-			break;
-	}
-
-	/*
-	 * Do a binary approximation to get loops_per_jiffy set to be equal
-	 * one clock (up to lps_precision bits)
-	 */
-	loops_per_jiffy >>= 1;
-	loopbit = loops_per_jiffy;
-	while (lps_precision-- && (loopbit >>= 1)) {
-		loops_per_jiffy |= loopbit;
-		ticks = jiffies;
-		while (ticks == jiffies);
-		ticks = jiffies;
-		__delay(loops_per_jiffy);
-		if (jiffies != ticks)	/* longer than 1 tick */
-			loops_per_jiffy &= ~loopbit;
-	}
-}
-
-static int pm_do_freq(ctl_table *ctl, int write, struct file *file,
-		      void __user *buffer, size_t *len, loff_t *ppos)
-{
-	int retval = 0, i;
-	unsigned long val, pll;
-#define TMPBUFLEN 64
-#define MAX_CPU_FREQ 396
-	char buf[TMPBUFLEN], *p;
-	unsigned long flags, intc0_mask, intc1_mask;
-	unsigned long old_baud_base, old_cpu_freq, old_clk, old_refresh;
-	unsigned long new_baud_base, new_cpu_freq, new_clk, new_refresh;
-	unsigned long baud_rate;
-
-	spin_lock_irqsave(&pm_lock, flags);
-	if (!write)
-		*len = 0;
-	else {
-		/* Parse the new frequency */
-		if (*len > TMPBUFLEN - 1) {
-			spin_unlock_irqrestore(&pm_lock, flags);
-			return -EFAULT;
-		}
-		if (copy_from_user(buf, buffer, *len)) {
-			spin_unlock_irqrestore(&pm_lock, flags);
-			return -EFAULT;
-		}
-		buf[*len] = 0;
-		p = buf;
-		val = simple_strtoul(p, &p, 0);
-		if (val > MAX_CPU_FREQ) {
-			spin_unlock_irqrestore(&pm_lock, flags);
-			return -EFAULT;
-		}
-
-		pll = val / 12;
-		if ((pll > 33) || (pll < 7)) {	/* 396 MHz max, 84 MHz min */
-			/* Revisit this for higher speed CPUs */
-			spin_unlock_irqrestore(&pm_lock, flags);
-			return -EFAULT;
-		}
-
-		old_baud_base = get_au1x00_uart_baud_base();
-		old_cpu_freq = get_au1x00_speed();
-
-		new_cpu_freq = pll * 12 * 1000000;
-	        new_baud_base = (new_cpu_freq / (2 * ((int)(au_readl(SYS_POWERCTRL)
-							    & 0x03) + 2) * 16));
-		set_au1x00_speed(new_cpu_freq);
-		set_au1x00_uart_baud_base(new_baud_base);
-
-		old_refresh = au_readl(MEM_SDREFCFG) & 0x1ffffff;
-		new_refresh = ((old_refresh * new_cpu_freq) / old_cpu_freq) |
-			      (au_readl(MEM_SDREFCFG) & ~0x1ffffff);
-
-		au_writel(pll, SYS_CPUPLL);
-		au_sync_delay(1);
-		au_writel(new_refresh, MEM_SDREFCFG);
-		au_sync_delay(1);
-
-		for (i = 0; i < 4; i++)
-			if (au_readl(UART_BASE + UART_MOD_CNTRL +
-				     i * 0x00100000) == 3) {
-				old_clk = au_readl(UART_BASE + UART_CLK +
-						   i * 0x00100000);
-				baud_rate = old_baud_base / old_clk;
-				/*
-				 * We won't get an exact baud rate and the error
-				 * could be significant enough that our new
-				 * calculation will result in a clock that will
-				 * give us a baud rate that's too far off from
-				 * what we really want.
-				 */
-				if (baud_rate > 100000)
-					baud_rate = 115200;
-				else if (baud_rate > 50000)
-					baud_rate = 57600;
-				else if (baud_rate > 30000)
-					baud_rate = 38400;
-				else if (baud_rate > 17000)
-					baud_rate = 19200;
-				else
-					baud_rate = 9600;
-				new_clk = new_baud_base / baud_rate;
-				au_writel(new_clk, UART_BASE + UART_CLK +
-					  i * 0x00100000);
-				au_sync_delay(10);
-			}
-	}
-
-	/*
-	 * We don't want _any_ interrupts other than match20. Otherwise our
-	 * au1000_calibrate_delay() calculation will be off, potentially a lot.
-	 */
-	intc0_mask = save_local_and_disable(0);
-	intc1_mask = save_local_and_disable(1);
-	val = 1 << (AU1000_TOY_MATCH2_INT - AU1000_INTC0_INT_BASE);
-	au_writel(val, IC0_MASKSET);	/* unmask */
-	au_writel(val, IC0_WAKESET);	/* enable wake-from-sleep */
-	au_sync();
-	spin_unlock_irqrestore(&pm_lock, flags);
-	au1000_calibrate_delay();
-	restore_local_and_enable(0, intc0_mask);
-	restore_local_and_enable(1, intc1_mask);
-
-	return retval;
-}
-#endif
-
-static struct ctl_table pm_table[] = {
-	{
-		.ctl_name	= CTL_UNNUMBERED,
-		.procname	= "sleep",
-		.data		= NULL,
-		.maxlen		= 0,
-		.mode		= 0600,
-		.proc_handler	= &pm_do_sleep
-	},
-#if !defined(CONFIG_SOC_AU1200) && !defined(CONFIG_SOC_AU1550)
-	{
-		.ctl_name	= CTL_UNNUMBERED,
-		.procname	= "freq",
-		.data		= NULL,
-		.maxlen		= 0,
-		.mode		= 0600,
-		.proc_handler	= &pm_do_freq
-	},
-#endif
-	{}
-};
-
-static struct ctl_table pm_dir_table[] = {
-	{
-		.ctl_name	= CTL_UNNUMBERED,
-		.procname	= "pm",
-		.mode		= 0555,
-		.child		= pm_table
-	},
-	{}
-};
-
-/*
- * Initialize power interface
- */
-static int __init pm_init(void)
-{
-	/* init TOY to tick at 1Hz. No need to wait for access bits
-	 * since there's plenty of time between here and the first
-	 * suspend cycle.
-	 */
-	if (au_readl(SYS_TOYTRIM) != 32767) {
-		au_writel(32767, SYS_TOYTRIM);
-		au_sync();
-	}
-
-	register_sysctl_table(pm_dir_table);
-	return 0;
-}
-
-__initcall(pm_init);
-
 #endif	/* CONFIG_PM */