Merge git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc-merge

author: Linus Torvalds <torvalds@g5.osdl.org> 2006-01-15 10:05:10 -0800
committer: Linus Torvalds <torvalds@g5.osdl.org> 2006-01-15 10:05:10 -0800
commit: fc03da1ca1954f103ed57daf90611cefa57b07e0 (patch)
tree: 2b9b44b1a39f7743c1c3d7bc89654792686d7dbc /arch
parent: caf5b04c82f05c65843b2d7189845d6c3df5a41e (diff)
parent: e05b3b4adbaeea508bd1c195f1f2e22c8251176b (diff)
44 files changed, 2266 insertions, 10461 deletions
diff --git a/arch/powerpc/Kconfig b/arch/powerpc/Kconfig
index 01feed0e2a1..df338c5cc91 100644
--- a/arch/powerpc/Kconfig
+++ b/arch/powerpc/Kconfig
@@ -78,17 +78,6 @@ config PPC_UDBG_16550
 	bool
 	default n
 
-config CRASH_DUMP
-	bool "kernel crash dumps (EXPERIMENTAL)"
-	depends on PPC_MULTIPLATFORM
-	depends on EXPERIMENTAL
-	help
-	  Build a kernel suitable for use as a kdump capture kernel.
-	  The kernel will be linked at a different address than normal, and
-	  so can only be used for Kdump.
-
-	  Don't change this unless you know what you are doing.
-
 config GENERIC_TBSYNC
 	bool
 	default y if PPC32 && SMP
@@ -584,6 +573,16 @@ config KEXEC
 	  support.  As of this writing the exact hardware interface is
 	  strongly in flux, so no good recommendation can be made.
 
+config CRASH_DUMP
+	bool "kernel crash dumps (EXPERIMENTAL)"
+	depends on PPC_MULTIPLATFORM && PPC64 && EXPERIMENTAL
+	help
+	  Build a kernel suitable for use as a kdump capture kernel.
+	  The kernel will be linked at a different address than normal, and
+	  so can only be used for Kdump.
+
+	  Don't change this unless you know what you are doing.
+
 config EMBEDDEDBOOT
 	bool
 	depends on 8xx || 8260
diff --git a/arch/powerpc/boot/Makefile b/arch/powerpc/boot/Makefile
index 788dec4c7ef..840ae595a61 100644
--- a/arch/powerpc/boot/Makefile
+++ b/arch/powerpc/boot/Makefile
@@ -27,6 +27,7 @@ BOOTCFLAGS	:= $(HOSTCFLAGS) -fno-builtin -nostdinc -isystem \
 BOOTAFLAGS	:= -D__ASSEMBLY__ $(BOOTCFLAGS) -traditional -nostdinc
 OBJCOPYFLAGS    := contents,alloc,load,readonly,data
 OBJCOPY_COFF_ARGS := -O aixcoff-rs6000 --set-start 0x500000
+OBJCOPY_MIB_ARGS  := -O aixcoff-rs6000 -R .stab -R .stabstr -R .comment
 
 zlib       := infblock.c infcodes.c inffast.c inflate.c inftrees.c infutil.c
 zlibheader := infblock.h infcodes.h inffast.h inftrees.h infutil.h
@@ -90,11 +91,11 @@ gz-sec  = $(foreach section, $(1), $(patsubst %,$(obj)/kernel-%.gz, $(section)))
 hostprogs-y		:= addnote addRamDisk hack-coff
 
 targets += zImage.vmode zImage.initrd.vmode zImage zImage.initrd \
-	   zImage.coff zImage.initrd.coff \
+	   zImage.coff zImage.initrd.coff miboot.image miboot.initrd.image \
 	   $(patsubst $(obj)/%,%, $(call obj-sec, $(required) $(initrd))) \
 	   $(patsubst $(obj)/%,%, $(call src-sec, $(required) $(initrd))) \
 	   $(patsubst $(obj)/%,%, $(call gz-sec, $(required) $(initrd))) \
-	   vmlinux.initrd
+	   vmlinux.initrd dummy.o
 extra-y			:= initrd.o
 
 quiet_cmd_ramdisk = RAMDISK $@
@@ -116,6 +117,10 @@ quiet_cmd_addsection = ADDSEC  $@
 quiet_cmd_addnote = ADDNOTE $@
       cmd_addnote = $(obj)/addnote $@
 
+quiet_cmd_gen-miboot = GEN     $@
+      cmd_gen-miboot = $(OBJCOPY) $(OBJCOPY_MIB_ARGS) \
+		       --add-section=$1=$(word 2, $^) $< $@
+
 quiet_cmd_gencoff = COFF    $@
       cmd_gencoff = $(OBJCOPY) $(OBJCOPY_COFF_ARGS) $@ && \
 		    $(obj)/hack-coff $@
@@ -141,19 +146,25 @@ $(obj)/zImage.initrd.vmode $(obj)/zImage.initrd.coff: obj-boot += $(call obj-sec
 $(obj)/zImage.initrd.vmode: $(call obj-sec, $(required) $(initrd)) $(obj-boot) $(srctree)/$(src)/zImage.lds
 	$(call cmd,bootld,$(obj-boot),zImage.lds)
 
-# For 32-bit powermacs, build the COFF images as well as the ELF images.
+# For 32-bit powermacs, build the COFF and miboot images
+# as well as the ELF images.
 coffimage-$(CONFIG_PPC_PMAC)-$(CONFIG_PPC32) := $(obj)/zImage.coff
 coffrdimg-$(CONFIG_PPC_PMAC)-$(CONFIG_PPC32) := $(obj)/zImage.initrd.coff
+mibootimg-$(CONFIG_PPC_PMAC)-$(CONFIG_PPC32) := $(obj)/miboot.image
+mibrdimg-$(CONFIG_PPC_PMAC)-$(CONFIG_PPC32)  := $(obj)/miboot.initrd.image
 
-$(obj)/zImage: $(obj)/zImage.vmode $(obj)/addnote $(coffimage-y-y)
+$(obj)/zImage: $(obj)/zImage.vmode $(obj)/addnote $(coffimage-y-y) \
+			$(mibootimg-y-y)
 	@cp -f $< $@
 	$(call if_changed,addnote)
 
-$(obj)/zImage.initrd: $(obj)/zImage.initrd.vmode $(obj)/addnote $(coffrdimg-y-y)
+$(obj)/zImage.initrd: $(obj)/zImage.initrd.vmode $(obj)/addnote \
+			$(coffrdimg-y-y) $(mibrdimg-y-y)
 	@cp -f $< $@
 	$(call if_changed,addnote)
 
-$(obj)/zImage.coff: $(call obj-sec, $(required)) $(obj-boot) $(srctree)/$(src)/zImage.coff.lds $(obj)/hack-coff
+$(obj)/zImage.coff: $(call obj-sec, $(required)) $(obj-boot) \
+			$(srctree)/$(src)/zImage.coff.lds $(obj)/hack-coff
 	$(call cmd,bootld,$(obj-boot),zImage.coff.lds)
 	$(call cmd,gencoff)
 
@@ -162,6 +173,12 @@ $(obj)/zImage.initrd.coff: $(call obj-sec, $(required) $(initrd)) $(obj-boot) \
 	$(call cmd,bootld,$(obj-boot),zImage.coff.lds)
 	$(call cmd,gencoff)
 
+$(obj)/miboot.image: $(obj)/dummy.o $(obj)/vmlinux.gz
+	$(call cmd,gen-miboot,image)
+
+$(obj)/miboot.initrd.image: $(obj)/miboot.image $(images)/ramdisk.image.gz
+	$(call cmd,gen-miboot,initrd)
+
 #-----------------------------------------------------------
 # build u-boot images
 #-----------------------------------------------------------
diff --git a/arch/powerpc/boot/dummy.c b/arch/powerpc/boot/dummy.c
new file mode 100644
index 00000000000..31dbf45bf99
--- /dev/null
+++ b/arch/powerpc/boot/dummy.c
@@ -0,0 +1,4 @@
+int main(void)
+{
+	return 0;
+}
diff --git a/arch/powerpc/configs/pmac32_defconfig b/arch/powerpc/configs/pmac32_defconfig
index 398203bd98e..2ace57d1e33 100644
--- a/arch/powerpc/configs/pmac32_defconfig
+++ b/arch/powerpc/configs/pmac32_defconfig
@@ -1,7 +1,7 @@
 #
 # Automatically generated make config: don't edit
-# Linux kernel version: 2.6.15-rc5
-# Tue Dec 13 17:24:05 2005
+# Linux kernel version: 2.6.15
+# Sat Jan 14 16:26:08 2006
 #
 # CONFIG_PPC64 is not set
 CONFIG_PPC32=y
@@ -15,11 +15,15 @@ CONFIG_EARLY_PRINTK=y
 CONFIG_GENERIC_NVRAM=y
 CONFIG_SCHED_NO_NO_OMIT_FRAME_POINTER=y
 CONFIG_ARCH_MAY_HAVE_PC_FDC=y
+CONFIG_PPC_OF=y
+# CONFIG_PPC_UDBG_16550 is not set
+# CONFIG_CRASH_DUMP is not set
+# CONFIG_GENERIC_TBSYNC is not set
 
 #
 # Processor support
 #
-CONFIG_6xx=y
+CONFIG_CLASSIC32=y
 # CONFIG_PPC_52xx is not set
 # CONFIG_PPC_82xx is not set
 # CONFIG_PPC_83xx is not set
@@ -28,6 +32,7 @@ CONFIG_6xx=y
 # CONFIG_8xx is not set
 # CONFIG_E200 is not set
 # CONFIG_E500 is not set
+CONFIG_6xx=y
 CONFIG_PPC_FPU=y
 CONFIG_ALTIVEC=y
 CONFIG_PPC_STD_MMU=y
@@ -53,17 +58,18 @@ CONFIG_POSIX_MQUEUE=y
 # CONFIG_BSD_PROCESS_ACCT is not set
 CONFIG_SYSCTL=y
 # CONFIG_AUDIT is not set
-CONFIG_HOTPLUG=y
-CONFIG_KOBJECT_UEVENT=y
 CONFIG_IKCONFIG=y
 CONFIG_IKCONFIG_PROC=y
 CONFIG_INITRAMFS_SOURCE=""
+# CONFIG_CC_OPTIMIZE_FOR_SIZE is not set
 # CONFIG_EMBEDDED is not set
 CONFIG_KALLSYMS=y
 # CONFIG_KALLSYMS_ALL is not set
 # CONFIG_KALLSYMS_EXTRA_PASS is not set
+CONFIG_HOTPLUG=y
 CONFIG_PRINTK=y
 CONFIG_BUG=y
+CONFIG_ELF_CORE=y
 CONFIG_BASE_FULL=y
 CONFIG_FUTEX=y
 CONFIG_EPOLL=y
@@ -72,8 +78,10 @@ CONFIG_CC_ALIGN_FUNCTIONS=0
 CONFIG_CC_ALIGN_LABELS=0
 CONFIG_CC_ALIGN_LOOPS=0
 CONFIG_CC_ALIGN_JUMPS=0
+CONFIG_SLAB=y
 # CONFIG_TINY_SHMEM is not set
 CONFIG_BASE_SMALL=0
+# CONFIG_SLOB is not set
 
 #
 # Loadable module support
@@ -113,13 +121,10 @@ CONFIG_PPC_MULTIPLATFORM=y
 # CONFIG_APUS is not set
 # CONFIG_PPC_CHRP is not set
 CONFIG_PPC_PMAC=y
-CONFIG_PPC_OF=y
 CONFIG_MPIC=y
 # CONFIG_PPC_RTAS is not set
 # CONFIG_MMIO_NVRAM is not set
-# CONFIG_CRASH_DUMP is not set
 CONFIG_PPC_MPC106=y
-# CONFIG_GENERIC_TBSYNC is not set
 CONFIG_CPU_FREQ=y
 CONFIG_CPU_FREQ_TABLE=y
 # CONFIG_CPU_FREQ_DEBUG is not set
@@ -195,6 +200,11 @@ CONFIG_CARDBUS=y
 # PC-card bridges
 #
 CONFIG_YENTA=m
+CONFIG_YENTA_O2=y
+CONFIG_YENTA_RICOH=y
+CONFIG_YENTA_TI=y
+CONFIG_YENTA_ENE_TUNE=y
+CONFIG_YENTA_TOSHIBA=y
 # CONFIG_PD6729 is not set
 # CONFIG_I82092 is not set
 CONFIG_PCCARD_NONSTATIC=m
@@ -464,7 +474,7 @@ CONFIG_IEEE80211_CRYPT_TKIP=m
 #
 # CONFIG_STANDALONE is not set
 CONFIG_PREVENT_FIRMWARE_BUILD=y
-CONFIG_FW_LOADER=m
+CONFIG_FW_LOADER=y
 # CONFIG_DEBUG_DRIVER is not set
 
 #
@@ -491,7 +501,7 @@ CONFIG_PROC_EVENTS=y
 # Block devices
 #
 # CONFIG_BLK_DEV_FD is not set
-CONFIG_MAC_FLOPPY=y
+CONFIG_MAC_FLOPPY=m
 # CONFIG_BLK_CPQ_DA is not set
 # CONFIG_BLK_CPQ_CISS_DA is not set
 # CONFIG_BLK_DEV_DAC960 is not set
@@ -603,7 +613,7 @@ CONFIG_SCSI_CONSTANTS=y
 # SCSI Transport Attributes
 #
 CONFIG_SCSI_SPI_ATTRS=y
-# CONFIG_SCSI_FC_ATTRS is not set
+CONFIG_SCSI_FC_ATTRS=y
 # CONFIG_SCSI_ISCSI_ATTRS is not set
 # CONFIG_SCSI_SAS_ATTRS is not set
 
@@ -645,12 +655,7 @@ CONFIG_SCSI_SYM53C8XX_MAX_TAGS=64
 # CONFIG_SCSI_QLOGIC_FC is not set
 # CONFIG_SCSI_QLOGIC_1280 is not set
 CONFIG_SCSI_QLA2XXX=y
-# CONFIG_SCSI_QLA21XX is not set
-# CONFIG_SCSI_QLA22XX is not set
-# CONFIG_SCSI_QLA2300 is not set
-# CONFIG_SCSI_QLA2322 is not set
-# CONFIG_SCSI_QLA6312 is not set
-# CONFIG_SCSI_QLA24XX is not set
+# CONFIG_SCSI_QLA2XXX_EMBEDDED_FIRMWARE is not set
 # CONFIG_SCSI_LPFC is not set
 # CONFIG_SCSI_DC395x is not set
 # CONFIG_SCSI_DC390T is not set
@@ -658,7 +663,7 @@ CONFIG_SCSI_QLA2XXX=y
 # CONFIG_SCSI_DEBUG is not set
 CONFIG_SCSI_MESH=y
 CONFIG_SCSI_MESH_SYNC_RATE=5
-CONFIG_SCSI_MESH_RESET_DELAY_MS=1000
+CONFIG_SCSI_MESH_RESET_DELAY_MS=4000
 CONFIG_SCSI_MAC53C94=y
 
 #
@@ -727,7 +732,6 @@ CONFIG_IEEE1394_SBP2=m
 CONFIG_IEEE1394_ETH1394=m
 CONFIG_IEEE1394_DV1394=m
 CONFIG_IEEE1394_RAWIO=m
-# CONFIG_IEEE1394_CMP is not set
 
 #
 # I2O device support
@@ -740,7 +744,7 @@ CONFIG_IEEE1394_RAWIO=m
 CONFIG_ADB=y
 CONFIG_ADB_CUDA=y
 CONFIG_ADB_PMU=y
-CONFIG_PMAC_APM_EMU=y
+CONFIG_PMAC_APM_EMU=m
 CONFIG_PMAC_MEDIABAY=y
 CONFIG_PMAC_BACKLIGHT=y
 CONFIG_INPUT_ADBHID=y
@@ -819,6 +823,7 @@ CONFIG_PCNET32=y
 # CONFIG_R8169 is not set
 # CONFIG_SIS190 is not set
 # CONFIG_SKGE is not set
+# CONFIG_SKY2 is not set
 # CONFIG_SK98LIN is not set
 # CONFIG_VIA_VELOCITY is not set
 # CONFIG_TIGON3 is not set
@@ -978,14 +983,14 @@ CONFIG_HW_CONSOLE=y
 CONFIG_SERIAL_8250=m
 # CONFIG_SERIAL_8250_CS is not set
 CONFIG_SERIAL_8250_NR_UARTS=4
+CONFIG_SERIAL_8250_RUNTIME_UARTS=4
 # CONFIG_SERIAL_8250_EXTENDED is not set
 
 #
 # Non-8250 serial port support
 #
 CONFIG_SERIAL_CORE=m
-# CONFIG_SERIAL_PMACZILOG is not set
-# CONFIG_SERIAL_JSM is not set
+CONFIG_SERIAL_PMACZILOG=m
 CONFIG_UNIX98_PTYS=y
 CONFIG_LEGACY_PTYS=y
 CONFIG_LEGACY_PTY_COUNT=256
@@ -1058,7 +1063,7 @@ CONFIG_I2C_ALGOBIT=y
 # CONFIG_I2C_I801 is not set
 # CONFIG_I2C_I810 is not set
 # CONFIG_I2C_PIIX4 is not set
-CONFIG_I2C_KEYWEST=m
+CONFIG_I2C_POWERMAC=y
 # CONFIG_I2C_MPC is not set
 # CONFIG_I2C_NFORCE2 is not set
 # CONFIG_I2C_PARPORT_LIGHT is not set
@@ -1160,7 +1165,6 @@ CONFIG_FB_ATY128=y
 CONFIG_FB_ATY=y
 CONFIG_FB_ATY_CT=y
 # CONFIG_FB_ATY_GENERIC_LCD is not set
-# CONFIG_FB_ATY_XL_INIT is not set
 CONFIG_FB_ATY_GX=y
 # CONFIG_FB_SAVAGE is not set
 # CONFIG_FB_SIS is not set
@@ -1169,7 +1173,6 @@ CONFIG_FB_ATY_GX=y
 CONFIG_FB_3DFX=y
 # CONFIG_FB_3DFX_ACCEL is not set
 # CONFIG_FB_VOODOO1 is not set
-# CONFIG_FB_CYBLA is not set
 # CONFIG_FB_TRIDENT is not set
 # CONFIG_FB_VIRTUAL is not set
 
@@ -1214,9 +1217,10 @@ CONFIG_SND_OSSEMUL=y
 CONFIG_SND_MIXER_OSS=m
 CONFIG_SND_PCM_OSS=m
 CONFIG_SND_SEQUENCER_OSS=y
+# CONFIG_SND_DYNAMIC_MINORS is not set
+CONFIG_SND_SUPPORT_OLD_API=y
 # CONFIG_SND_VERBOSE_PRINTK is not set
 # CONFIG_SND_DEBUG is not set
-CONFIG_SND_GENERIC_DRIVER=y
 
 #
 # Generic devices
@@ -1230,6 +1234,8 @@ CONFIG_SND_DUMMY=m
 #
 # PCI devices
 #
+# CONFIG_SND_AD1889 is not set
+# CONFIG_SND_ALS4000 is not set
 # CONFIG_SND_ALI5451 is not set
 # CONFIG_SND_ATIIXP is not set
 # CONFIG_SND_ATIIXP_MODEM is not set
@@ -1238,45 +1244,44 @@ CONFIG_SND_DUMMY=m
 # CONFIG_SND_AU8830 is not set
 # CONFIG_SND_AZT3328 is not set
 # CONFIG_SND_BT87X is not set
-# CONFIG_SND_CS46XX is not set
+# CONFIG_SND_CA0106 is not set
+# CONFIG_SND_CMIPCI is not set
 # CONFIG_SND_CS4281 is not set
+# CONFIG_SND_CS46XX is not set
 # CONFIG_SND_EMU10K1 is not set
 # CONFIG_SND_EMU10K1X is not set
-# CONFIG_SND_CA0106 is not set
-# CONFIG_SND_KORG1212 is not set
-# CONFIG_SND_MIXART is not set
-# CONFIG_SND_NM256 is not set
-# CONFIG_SND_RME32 is not set
-# CONFIG_SND_RME96 is not set
-# CONFIG_SND_RME9652 is not set
-# CONFIG_SND_HDSP is not set
-# CONFIG_SND_HDSPM is not set
-# CONFIG_SND_TRIDENT is not set
-# CONFIG_SND_YMFPCI is not set
-# CONFIG_SND_AD1889 is not set
-# CONFIG_SND_ALS4000 is not set
-# CONFIG_SND_CMIPCI is not set
 # CONFIG_SND_ENS1370 is not set
 # CONFIG_SND_ENS1371 is not set
 # CONFIG_SND_ES1938 is not set
 # CONFIG_SND_ES1968 is not set
-# CONFIG_SND_MAESTRO3 is not set
 # CONFIG_SND_FM801 is not set
+# CONFIG_SND_HDA_INTEL is not set
+# CONFIG_SND_HDSP is not set
+# CONFIG_SND_HDSPM is not set
 # CONFIG_SND_ICE1712 is not set
 # CONFIG_SND_ICE1724 is not set
 # CONFIG_SND_INTEL8X0 is not set
 # CONFIG_SND_INTEL8X0M is not set
+# CONFIG_SND_KORG1212 is not set
+# CONFIG_SND_MAESTRO3 is not set
+# CONFIG_SND_MIXART is not set
+# CONFIG_SND_NM256 is not set
+# CONFIG_SND_PCXHR is not set
+# CONFIG_SND_RME32 is not set
+# CONFIG_SND_RME96 is not set
+# CONFIG_SND_RME9652 is not set
 # CONFIG_SND_SONICVIBES is not set
+# CONFIG_SND_TRIDENT is not set
 # CONFIG_SND_VIA82XX is not set
 # CONFIG_SND_VIA82XX_MODEM is not set
 # CONFIG_SND_VX222 is not set
-# CONFIG_SND_HDA_INTEL is not set
+# CONFIG_SND_YMFPCI is not set
 
 #
 # ALSA PowerMac devices
 #
 CONFIG_SND_POWERMAC=m
-# CONFIG_SND_POWERMAC_AUTO_DRC is not set
+CONFIG_SND_POWERMAC_AUTO_DRC=y
 
 #
 # USB devices
@@ -1336,6 +1341,7 @@ CONFIG_USB_PRINTER=m
 # may also be needed; see USB_STORAGE Help for more information
 #
 # CONFIG_USB_STORAGE is not set
+# CONFIG_USB_LIBUSUAL is not set
 
 #
 # USB Input Devices
@@ -1355,6 +1361,7 @@ CONFIG_USB_HIDINPUT=y
 # CONFIG_USB_YEALINK is not set
 # CONFIG_USB_XPAD is not set
 # CONFIG_USB_ATI_REMOTE is not set
+# CONFIG_USB_ATI_REMOTE2 is not set
 # CONFIG_USB_KEYSPAN_REMOTE is not set
 CONFIG_USB_APPLETOUCH=y
 
@@ -1501,6 +1508,7 @@ CONFIG_FS_MBCACHE=y
 # CONFIG_JFS_FS is not set
 # CONFIG_FS_POSIX_ACL is not set
 # CONFIG_XFS_FS is not set
+# CONFIG_OCFS2_FS is not set
 # CONFIG_MINIX_FS is not set
 # CONFIG_ROMFS_FS is not set
 CONFIG_INOTIFY=y
@@ -1540,6 +1548,7 @@ CONFIG_TMPFS=y
 # CONFIG_HUGETLB_PAGE is not set
 CONFIG_RAMFS=y
 CONFIG_RELAYFS_FS=m
+# CONFIG_CONFIGFS_FS is not set
 
 #
 # Miscellaneous filesystems
@@ -1670,12 +1679,13 @@ CONFIG_OPROFILE=y
 # Kernel hacking
 #
 # CONFIG_PRINTK_TIME is not set
-CONFIG_DEBUG_KERNEL=y
 # CONFIG_MAGIC_SYSRQ is not set
+CONFIG_DEBUG_KERNEL=y
 CONFIG_LOG_BUF_SHIFT=14
 CONFIG_DETECT_SOFTLOCKUP=y
 # CONFIG_SCHEDSTATS is not set
 # CONFIG_DEBUG_SLAB is not set
+# CONFIG_DEBUG_MUTEXES is not set
 # CONFIG_DEBUG_SPINLOCK is not set
 # CONFIG_DEBUG_SPINLOCK_SLEEP is not set
 # CONFIG_DEBUG_KOBJECT is not set
@@ -1688,6 +1698,11 @@ CONFIG_XMON=y
 CONFIG_XMON_DEFAULT=y
 # CONFIG_BDI_SWITCH is not set
 CONFIG_BOOTX_TEXT=y
+# CONFIG_PPC_EARLY_DEBUG_LPAR is not set
+# CONFIG_PPC_EARLY_DEBUG_G5 is not set
+# CONFIG_PPC_EARLY_DEBUG_RTAS is not set
+# CONFIG_PPC_EARLY_DEBUG_MAPLE is not set
+# CONFIG_PPC_EARLY_DEBUG_ISERIES is not set
 
 #
 # Security options
diff --git a/arch/powerpc/kernel/Makefile b/arch/powerpc/kernel/Makefile
index a94699d8dc5..c287980b7e6 100644
--- a/arch/powerpc/kernel/Makefile
+++ b/arch/powerpc/kernel/Makefile
@@ -60,7 +60,8 @@ obj-$(CONFIG_MODULES)		+= $(module-y)
 
 pci64-$(CONFIG_PPC64)		+= pci_64.o pci_dn.o pci_iommu.o \
 				   pci_direct_iommu.o iomap.o
-obj-$(CONFIG_PCI)		+= $(pci64-y)
+pci32-$(CONFIG_PPC32)		:= pci_32.o
+obj-$(CONFIG_PCI)		+= $(pci64-y) $(pci32-y)
 kexec-$(CONFIG_PPC64)		:= machine_kexec_64.o crash.o
 kexec-$(CONFIG_PPC32)		:= machine_kexec_32.o
 obj-$(CONFIG_KEXEC)		+= machine_kexec.o $(kexec-y)
diff --git a/arch/powerpc/kernel/crash.c b/arch/powerpc/kernel/crash.c
index 5f248e3fdf8..8c21d378f5d 100644
--- a/arch/powerpc/kernel/crash.c
+++ b/arch/powerpc/kernel/crash.c
@@ -84,7 +84,10 @@ static void crash_save_this_cpu(struct pt_regs *regs, int cpu)
 	 * squirrelled away.  ELF notes happen to provide
 	 * all of that that no need to invent something new.
 	 */
-	buf = &crash_notes[cpu][0];
+	buf = (u32*)per_cpu_ptr(crash_notes, cpu);
+	if (!buf) 
+		return;
+
 	memset(&prstatus, 0, sizeof(prstatus));
 	prstatus.pr_pid = current->pid;
 	elf_core_copy_regs(&prstatus.pr_reg, regs);
@@ -93,76 +96,6 @@ static void crash_save_this_cpu(struct pt_regs *regs, int cpu)
 	final_note(buf);
 }
 
-/* FIXME Merge this with xmon_save_regs ?? */
-static inline void crash_get_current_regs(struct pt_regs *regs)
-{
-	unsigned long tmp1, tmp2;
-
-	__asm__ __volatile__ (
-		"std    0,0(%2)\n"
-		"std    1,8(%2)\n"
-		"std    2,16(%2)\n"
-		"std    3,24(%2)\n"
-		"std    4,32(%2)\n"
-		"std    5,40(%2)\n"
-		"std    6,48(%2)\n"
-		"std    7,56(%2)\n"
-		"std    8,64(%2)\n"
-		"std    9,72(%2)\n"
-		"std    10,80(%2)\n"
-		"std    11,88(%2)\n"
-		"std    12,96(%2)\n"
-		"std    13,104(%2)\n"
-		"std    14,112(%2)\n"
-		"std    15,120(%2)\n"
-		"std    16,128(%2)\n"
-		"std    17,136(%2)\n"
-		"std    18,144(%2)\n"
-		"std    19,152(%2)\n"
-		"std    20,160(%2)\n"
-		"std    21,168(%2)\n"
-		"std    22,176(%2)\n"
-		"std    23,184(%2)\n"
-		"std    24,192(%2)\n"
-		"std    25,200(%2)\n"
-		"std    26,208(%2)\n"
-		"std    27,216(%2)\n"
-		"std    28,224(%2)\n"
-		"std    29,232(%2)\n"
-		"std    30,240(%2)\n"
-		"std    31,248(%2)\n"
-		"mfmsr  %0\n"
-		"std    %0, 264(%2)\n"
-		"mfctr  %0\n"
-		"std    %0, 280(%2)\n"
-		"mflr   %0\n"
-		"std    %0, 288(%2)\n"
-		"bl     1f\n"
-	"1:      mflr   %1\n"
-		"std    %1, 256(%2)\n"
-		"mtlr   %0\n"
-		"mfxer  %0\n"
-		"std    %0, 296(%2)\n"
-		: "=&r" (tmp1), "=&r" (tmp2)
-		: "b" (regs));
-}
-
-/* We may have saved_regs from where the error came from
- * or it is NULL if via a direct panic().
- */
-static void crash_save_self(struct pt_regs *saved_regs)
-{
-	struct pt_regs regs;
-	int cpu;
-
-	cpu = smp_processor_id();
-	if (saved_regs)
-		memcpy(&regs, saved_regs, sizeof(regs));
-	else
-		crash_get_current_regs(&regs);
-	crash_save_this_cpu(&regs, cpu);
-}
-
 #ifdef CONFIG_SMP
 static atomic_t waiting_for_crash_ipi;
 
@@ -260,5 +193,5 @@ void default_machine_crash_shutdown(struct pt_regs *regs)
 	 */
 	crashing_cpu = smp_processor_id();
 	crash_kexec_prepare_cpus();
-	crash_save_self(regs);
+	crash_save_this_cpu(regs, crashing_cpu);
 }
diff --git a/arch/powerpc/kernel/pci_32.c b/arch/powerpc/kernel/pci_32.c
new file mode 100644
index 00000000000..704c846b2b0
--- /dev/null
+++ b/arch/powerpc/kernel/pci_32.c
@@ -0,0 +1,1897 @@
+/*
+ * Common pmac/prep/chrp pci routines. -- Cort
+ */
+
+#include <linux/config.h>
+#include <linux/kernel.h>
+#include <linux/pci.h>
+#include <linux/delay.h>
+#include <linux/string.h>
+#include <linux/init.h>
+#include <linux/capability.h>
+#include <linux/sched.h>
+#include <linux/errno.h>
+#include <linux/bootmem.h>
+
+#include <asm/processor.h>
+#include <asm/io.h>
+#include <asm/prom.h>
+#include <asm/sections.h>
+#include <asm/pci-bridge.h>
+#include <asm/byteorder.h>
+#include <asm/irq.h>
+#include <asm/uaccess.h>
+#include <asm/machdep.h>
+
+#undef DEBUG
+
+#ifdef DEBUG
+#define DBG(x...) printk(x)
+#else
+#define DBG(x...)
+#endif
+
+unsigned long isa_io_base     = 0;
+unsigned long isa_mem_base    = 0;
+unsigned long pci_dram_offset = 0;
+int pcibios_assign_bus_offset = 1;
+
+void pcibios_make_OF_bus_map(void);
+
+static int pci_relocate_bridge_resource(struct pci_bus *bus, int i);
+static int probe_resource(struct pci_bus *parent, struct resource *pr,
+			  struct resource *res, struct resource **conflict);
+static void update_bridge_base(struct pci_bus *bus, int i);
+static void pcibios_fixup_resources(struct pci_dev* dev);
+static void fixup_broken_pcnet32(struct pci_dev* dev);
+static int reparent_resources(struct resource *parent, struct resource *res);
+static void fixup_cpc710_pci64(struct pci_dev* dev);
+#ifdef CONFIG_PPC_OF
+static u8* pci_to_OF_bus_map;
+#endif
+
+/* By default, we don't re-assign bus numbers. We do this only on
+ * some pmacs
+ */
+int pci_assign_all_buses;
+
+struct pci_controller* hose_head;
+struct pci_controller** hose_tail = &hose_head;
+
+static int pci_bus_count;
+
+static void
+fixup_broken_pcnet32(struct pci_dev* dev)
+{
+	if ((dev->class>>8 == PCI_CLASS_NETWORK_ETHERNET)) {
+		dev->vendor = PCI_VENDOR_ID_AMD;
+		pci_write_config_word(dev, PCI_VENDOR_ID, PCI_VENDOR_ID_AMD);
+	}
+}
+DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_TRIDENT,	PCI_ANY_ID,			fixup_broken_pcnet32);
+
+static void
+fixup_cpc710_pci64(struct pci_dev* dev)
+{
+	/* Hide the PCI64 BARs from the kernel as their content doesn't
+	 * fit well in the resource management
+	 */
+	dev->resource[0].start = dev->resource[0].end = 0;
+	dev->resource[0].flags = 0;
+	dev->resource[1].start = dev->resource[1].end = 0;
+	dev->resource[1].flags = 0;
+}
+DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_IBM,	PCI_DEVICE_ID_IBM_CPC710_PCI64,	fixup_cpc710_pci64);
+
+static void
+pcibios_fixup_resources(struct pci_dev *dev)
+{
+	struct pci_controller* hose = (struct pci_controller *)dev->sysdata;
+	int i;
+	unsigned long offset;
+
+	if (!hose) {
+		printk(KERN_ERR "No hose for PCI dev %s!\n", pci_name(dev));
+		return;
+	}
+	for (i = 0; i < DEVICE_COUNT_RESOURCE; i++) {
+		struct resource *res = dev->resource + i;
+		if (!res->flags)
+			continue;
+		if (res->end == 0xffffffff) {
+			DBG("PCI:%s Resource %d [%08lx-%08lx] is unassigned\n",
+			    pci_name(dev), i, res->start, res->end);
+			res->end -= res->start;
+			res->start = 0;
+			res->flags |= IORESOURCE_UNSET;
+			continue;
+		}
+		offset = 0;
+		if (res->flags & IORESOURCE_MEM) {
+			offset = hose->pci_mem_offset;
+		} else if (res->flags & IORESOURCE_IO) {
+			offset = (unsigned long) hose->io_base_virt
+				- isa_io_base;
+		}
+		if (offset != 0) {
+			res->start += offset;
+			res->end += offset;
+#ifdef DEBUG
+			printk("Fixup res %d (%lx) of dev %s: %lx -> %lx\n",
+			       i, res->flags, pci_name(dev),
+			       res->start - offset, res->start);
+#endif
+		}
+	}
+
+	/* Call machine specific resource fixup */
+	if (ppc_md.pcibios_fixup_resources)
+		ppc_md.pcibios_fixup_resources(dev);
+}
+DECLARE_PCI_FIXUP_HEADER(PCI_ANY_ID,		PCI_ANY_ID,			pcibios_fixup_resources);
+
+void pcibios_resource_to_bus(struct pci_dev *dev, struct pci_bus_region *region,
+			struct resource *res)
+{
+	unsigned long offset = 0;
+	struct pci_controller *hose = dev->sysdata;
+
+	if (hose && res->flags & IORESOURCE_IO)
+		offset = (unsigned long)hose->io_base_virt - isa_io_base;
+	else if (hose && res->flags & IORESOURCE_MEM)
+		offset = hose->pci_mem_offset;
+	region->start = res->start - offset;
+	region->end = res->end - offset;
+}
+EXPORT_SYMBOL(pcibios_resource_to_bus);
+
+void pcibios_bus_to_resource(struct pci_dev *dev, struct resource *res,
+			     struct pci_bus_region *region)
+{
+	unsigned long offset = 0;
+	struct pci_controller *hose = dev->sysdata;
+
+	if (hose && res->flags & IORESOURCE_IO)
+		offset = (unsigned long)hose->io_base_virt - isa_io_base;
+	else if (hose && res->flags & IORESOURCE_MEM)
+		offset = hose->pci_mem_offset;
+	res->start = region->start + offset;
+	res->end = region->end + offset;
+}
+EXPORT_SYMBOL(pcibios_bus_to_resource);
+
+/*
+ * We need to avoid collisions with `mirrored' VGA ports
+ * and other strange ISA hardware, so we always want the
+ * addresses to be allocated in the 0x000-0x0ff region
+ * modulo 0x400.
+ *
+ * Why? Because some silly external IO cards only decode
+ * the low 10 bits of the IO address. The 0x00-0xff region
+ * is reserved for motherboard devices that decode all 16
+ * bits, so it's ok to allocate at, say, 0x2800-0x28ff,
+ * but we want to try to avoid allocating at 0x2900-0x2bff
+ * which might have be mirrored at 0x0100-0x03ff..
+ */
+void pcibios_align_resource(void *data, struct resource *res, unsigned long size,
+		       unsigned long align)
+{
+	struct pci_dev *dev = data;
+
+	if (res->flags & IORESOURCE_IO) {
+		unsigned long start = res->start;
+
+		if (size > 0x100) {
+			printk(KERN_ERR "PCI: I/O Region %s/%d too large"
+			       " (%ld bytes)\n", pci_name(dev),
+			       dev->resource - res, size);
+		}
+
+		if (start & 0x300) {
+			start = (start + 0x3ff) & ~0x3ff;
+			res->start = start;
+		}
+	}
+}
+EXPORT_SYMBOL(pcibios_align_resource);
+
+/*
+ *  Handle resources of PCI devices.  If the world were perfect, we could
+ *  just allocate all the resource regions and do nothing more.  It isn't.
+ *  On the other hand, we cannot just re-allocate all devices, as it would
+ *  require us to know lots of host bridge internals.  So we attempt to
+ *  keep as much of the original configuration as possible, but tweak it
+ *  when it's found to be wrong.
+ *
+ *  Known BIOS problems we have to work around:
+ *	- I/O or memory regions not configured
+ *	- regions configured, but not enabled in the command register
+ *	- bogus I/O addresses above 64K used
+ *	- expansion ROMs left enabled (this may sound harmless, but given
+ *	  the fact the PCI specs explicitly allow address decoders to be
+ *	  shared between expansion ROMs and other resource regions, it's
+ *	  at least dangerous)
+ *
+ *  Our solution:
+ *	(1) Allocate resources for all buses behind PCI-to-PCI bridges.
+ *	    This gives us fixed barriers on where we can allocate.
+ *	(2) Allocate resources for all enabled devices.  If there is
+ *	    a collision, just mark the resource as unallocated. Also
+ *	    disable expansion ROMs during this step.
+ *	(3) Try to allocate resources for disabled devices.  If the
+ *	    resources were assigned correctly, everything goes well,
+ *	    if they weren't, they won't disturb allocation of other
+ *	    resources.
+ *	(4) Assign new addresses to resources which were either
+ *	    not configured at all or misconfigured.  If explicitly
+ *	    requested by the user, configure expansion ROM address
+ *	    as well.
+ */
+
+static void __init
+pcibios_allocate_bus_resources(struct list_head *bus_list)
+{
+	struct pci_bus *bus;
+	int i;
+	struct resource *res, *pr;
+
+	/* Depth-First Search on bus tree */
+	list_for_each_entry(bus, bus_list, node) {
+		for (i = 0; i < 4; ++i) {
+			if ((res = bus->resource[i]) == NULL || !res->flags
+			    || res->start > res->end)
+				continue;
+			if (bus->parent == NULL)
+				pr = (res->flags & IORESOURCE_IO)?
+					&ioport_resource: &iomem_resource;
+			else {
+				pr = pci_find_parent_resource(bus->self, res);
+				if (pr == res) {
+					/* this happens when the generic PCI
+					 * code (wrongly) decides that this
+					 * bridge is transparent  -- paulus
+					 */
+					continue;
+				}
+			}
+
+			DBG("PCI: bridge rsrc %lx..%lx (%lx), parent %p\n",
+			    res->start, res->end, res->flags, pr);
+			if (pr) {
+				if (request_resource(pr, res) == 0)
+					continue;
+				/*
+				 * Must be a conflict with an existing entry.
+				 * Move that entry (or entries) under the
+				 * bridge resource and try again.
+				 */
+				if (reparent_resources(pr, res) == 0)
+					continue;
+			}
+			printk(KERN_ERR "PCI: Cannot allocate resource region "
+			       "%d of PCI bridge %d\n", i, bus->number);
+			if (pci_relocate_bridge_resource(bus, i))
+				bus->resource[i] = NULL;
+		}
+		pcibios_allocate_bus_resources(&bus->children);
+	}
+}
+
+/*
+ * Reparent resource children of pr that conflict with res
+ * under res, and make res replace those children.
+ */
+static int __init
+reparent_resources(struct resource *parent, struct resource *res)
+{
+	struct resource *p, **pp;
+	struct resource **firstpp = NULL;
+
+	for (pp = &parent->child; (p = *pp) != NULL; pp = &p->sibling) {
+		if (p->end < res->start)
+			continue;
+		if (res->end < p->start)
+			break;
+		if (p->start < res->start || p->end > res->end)
+			return -1;	/* not completely contained */
+		if (firstpp == NULL)
+			firstpp = pp;
+	}
+	if (firstpp == NULL)
+		return -1;	/* didn't find any conflicting entries? */
+	res->parent = parent;
+	res->child = *firstpp;
+	res->sibling = *pp;
+	*firstpp = res;
+	*pp = NULL;
+	for (p = res->child; p != NULL; p = p->sibling) {
+		p->parent = res;
+		DBG(KERN_INFO "PCI: reparented %s [%lx..%lx] under %s\n",
+		    p->name, p->start, p->end, res->name);
+	}
+	return 0;
+}
+
+/*
+ * A bridge has been allocated a range which is outside the range
+ * of its parent bridge, so it needs to be moved.
+ */
+static int __init
+pci_relocate_bridge_resource(struct pci_bus *bus, int i)
+{
+	struct resource *res, *pr, *conflict;
+	unsigned long try, size;
+	int j;
+	struct pci_bus *parent = bus->parent;
+
+	if (parent == NULL) {
+		/* shouldn't ever happen */
+		printk(KERN_ERR "PCI: can't move host bridge resource\n");
+		return -1;
+	}
+	res = bus->resource[i];
+	if (res == NULL)
+		return -1;
+	pr = NULL;
+	for (j = 0; j < 4; j++) {
+		struct resource *r = parent->resource[j];
+		if (!r)
+			continue;
+		if ((res->flags ^ r->flags) & (IORESOURCE_IO | IORESOURCE_MEM))
+			continue;
+		if (!((res->flags ^ r->flags) & IORESOURCE_PREFETCH)) {
+			pr = r;
+			break;
+		}
+		if (res->flags & IORESOURCE_PREFETCH)
+			pr = r;
+	}
+	if (pr == NULL)
+		return -1;
+	size = res->end - res->start;
+	if (pr->start > pr->end || size > pr->end - pr->start)
+		return -1;
+	try = pr->end;
+	for (;;) {
+		res->start = try - size;
+		res->end = try;
+		if (probe_resource(bus->parent, pr, res, &conflict) == 0)
+			break;
+		if (conflict->start <= pr->start + size)
+			return -1;
+		try = conflict->start - 1;
+	}
+	if (request_resource(pr, res)) {
+		DBG(KERN_ERR "PCI: huh? couldn't move to %lx..%lx\n",
+		    res->start, res->end);
+		return -1;		/* "can't happen" */
+	}
+	update_bridge_base(bus, i);
+	printk(KERN_INFO "PCI: bridge %d resource %d moved to %lx..%lx\n",
+	       bus->number, i, res->start, res->end);
+	return 0;
+}
+
+static int __init
+probe_resource(struct pci_bus *parent, struct resource *pr,
+	       struct resource *res, struct resource **conflict)
+{
+	struct pci_bus *bus;
+	struct pci_dev *dev;
+	struct resource *r;
+	int i;
+
+	for (r = pr->child; r != NULL; r = r->sibling) {
+		if (r->end >= res->start && res->end >= r->start) {
+			*conflict = r;
+			return 1;
+		}
+	}
+	list_for_each_entry(bus, &parent->children, node) {
+		for (i = 0; i < 4; ++i) {
+			if ((r = bus->resource[i]) == NULL)
+				continue;
+			if (!r->flags || r->start > r->end || r == res)
+				continue;
+			if (pci_find_parent_resource(bus->self, r) != pr)
+				continue;
+			if (r->end >= res->start && res->end >= r->start) {
+				*conflict = r;
+				return 1;
+			}
+		}
+	}
+	list_for_each_entry(dev, &parent->devices, bus_list) {
+		for (i = 0; i < 6; ++i) {
+			r = &dev->resource[i];
+			if (!r->flags || (r->flags & IORESOURCE_UNSET))
+				continue;
+			if (pci_find_parent_resource(dev, r) != pr)
+				continue;
+			if (r->end >= res->start && res->end >= r->start) {
+				*conflict = r;
+				return 1;
+			}
+		}
+	}
+	return 0;
+}
+
+static void __init
+update_bridge_base(struct pci_bus *bus, int i)
+{
+	struct resource *res = bus->resource[i];
+	u8 io_base_lo, io_limit_lo;
+	u16 mem_base, mem_limit;
+	u16 cmd;
+	unsigned long start, end, off;
+	struct pci_dev *dev = bus->self;
+	struct pci_controller *hose = dev->sysdata;
+
+	if (!hose) {
+		printk("update_bridge_base: no hose?\n");
+		return;
+	}
+	pci_read_config_word(dev, PCI_COMMAND, &cmd);
+	pci_write_config_word(dev, PCI_COMMAND,
+			      cmd & ~(PCI_COMMAND_IO | PCI_COMMAND_MEMORY));
+	if (res->flags & IORESOURCE_IO) {
+		off = (unsigned long) hose->io_base_virt - isa_io_base;
+		start = res->start - off;
+		end = res->end - off;
+		io_base_lo = (start >> 8) & PCI_IO_RANGE_MASK;
+		io_limit_lo = (end >> 8) & PCI_IO_RANGE_MASK;
+		if (end > 0xffff) {
+			pci_write_config_word(dev, PCI_IO_BASE_UPPER16,
+					      start >> 16);
+			pci_write_config_word(dev, PCI_IO_LIMIT_UPPER16,
+					      end >> 16);
+			io_base_lo |= PCI_IO_RANGE_TYPE_32;
+		} else
+			io_base_lo |= PCI_IO_RANGE_TYPE_16;
+		pci_write_config_byte(dev, PCI_IO_BASE, io_base_lo);
+		pci_write_config_byte(dev, PCI_IO_LIMIT, io_limit_lo);
+
+	} else if ((res->flags & (IORESOURCE_MEM | IORESOURCE_PREFETCH))
+		   == IORESOURCE_MEM) {
+		off = hose->pci_mem_offset;
+		mem_base = ((res->start - off) >> 16) & PCI_MEMORY_RANGE_MASK;
+		mem_limit = ((res->end - off) >> 16) & PCI_MEMORY_RANGE_MASK;
+		pci_write_config_word(dev, PCI_MEMORY_BASE, mem_base);
+		pci_write_config_word(dev, PCI_MEMORY_LIMIT, mem_limit);
+
+	} else if ((res->flags & (IORESOURCE_MEM | IORESOURCE_PREFETCH))
+		   == (IORESOURCE_MEM | IORESOURCE_PREFETCH)) {
+		off = hose->pci_mem_offset;
+		mem_base = ((res->start - off) >> 16) & PCI_PREF_RANGE_MASK;
+		mem_limit = ((res->end - off) >> 16) & PCI_PREF_RANGE_MASK;
+		pci_write_config_word(dev, PCI_PREF_MEMORY_BASE, mem_base);
+		pci_write_config_word(dev, PCI_PREF_MEMORY_LIMIT, mem_limit);
+
+	} else {
+		DBG(KERN_ERR "PCI: ugh, bridge %s res %d has flags=%lx\n",
+		    pci_name(dev), i, res->flags);
+	}
+	pci_write_config_word(dev, PCI_COMMAND, cmd);
+}
+
+static inline void alloc_resource(struct pci_dev *dev, int idx)
+{
+	struct resource *pr, *r = &dev->resource[idx];
+
+	DBG("PCI:%s: Resource %d: %08lx-%08lx (f=%lx)\n",
+	    pci_name(dev), idx, r->start, r->end, r->flags);
+	pr = pci_find_parent_resource(dev, r);
+	if (!pr || request_resource(pr, r) < 0) {
+		printk(KERN_ERR "PCI: Cannot allocate resource region %d"
+		       " of device %s\n", idx, pci_name(dev));
+		if (pr)
+			DBG("PCI:  parent is %p: %08lx-%08lx (f=%lx)\n",
+			    pr, pr->start, pr->end, pr->flags);
+		/* We'll assign a new address later */
+		r->flags |= IORESOURCE_UNSET;
+		r->end -= r->start;
+		r->start = 0;
+	}
+}
+
+static void __init
+pcibios_allocate_resources(int pass)
+{
+	struct pci_dev *dev = NULL;
+	int idx, disabled;
+	u16 command;
+	struct resource *r;
+
+	for_each_pci_dev(dev) {
+		pci_read_config_word(dev, PCI_COMMAND, &command);
+		for (idx = 0; idx < 6; idx++) {
+			r = &dev->resource[idx];
+			if (r->parent)		/* Already allocated */
+				continue;
+			if (!r->flags || (r->flags & IORESOURCE_UNSET))
+				continue;	/* Not assigned at all */
+			if (r->flags & IORESOURCE_IO)
+				disabled = !(command & PCI_COMMAND_IO);
+			else
+				disabled = !(command & PCI_COMMAND_MEMORY);
+			if (pass == disabled)
+				alloc_resource(dev, idx);
+		}
+		if (pass)
+			continue;
+		r = &dev->resource[PCI_ROM_RESOURCE];
+		if (r->flags & IORESOURCE_ROM_ENABLE) {
+			/* Turn the ROM off, leave the resource region, but keep it unregistered. */
+			u32 reg;
+			DBG("PCI: Switching off ROM of %s\n", pci_name(dev));
+			r->flags &= ~IORESOURCE_ROM_ENABLE;
+			pci_read_config_dword(dev, dev->rom_base_reg, &reg);
+			pci_write_config_dword(dev, dev->rom_base_reg,
+					       reg & ~PCI_ROM_ADDRESS_ENABLE);
+		}
+	}
+}
+
+static void __init
+pcibios_assign_resources(void)
+{
+	struct pci_dev *dev = NULL;
+	int idx;
+	struct resource *r;
+
+	for_each_pci_dev(dev) {
+		int class = dev->class >> 8;
+
+		/* Don't touch classless devices and host bridges */
+		if (!class || class == PCI_CLASS_BRIDGE_HOST)
+			continue;
+
+		for (idx = 0; idx < 6; idx++) {
+			r = &dev->resource[idx];
+
+			/*
+			 * We shall assign a new address to this resource,
+			 * either because the BIOS (sic) forgot to do so
+			 * or because we have decided the old address was
+			 * unusable for some reason.
+			 */
+			if ((r->flags & IORESOURCE_UNSET) && r->end &&
+			    (!ppc_md.pcibios_enable_device_hook ||
+			     !ppc_md.pcibios_enable_device_hook(dev, 1))) {
+				r->flags &= ~IORESOURCE_UNSET;
+				pci_assign_resource(dev, idx);
+			}
+		}
+
+#if 0 /* don't assign ROMs */
+		r = &dev->resource[PCI_ROM_RESOURCE];
+		r->end -= r->start;
+		r->start = 0;
+		if (r->end)
+			pci_assign_resource(dev, PCI_ROM_RESOURCE);
+#endif
+	}
+}
+
+
+int
+pcibios_enable_resources(struct pci_dev *dev, int mask)
+{
+	u16 cmd, old_cmd;
+	int idx;
+	struct resource *r;
+
+	pci_read_config_word(dev, PCI_COMMAND, &cmd);
+	old_cmd = cmd;
+	for (idx=0; idx<6; idx++) {
+		/* Only set up the requested stuff */
+		if (!(mask & (1<<idx)))
+			continue;
+	
+		r = &dev->resource[idx];
+		if (r->flags & IORESOURCE_UNSET) {
+			printk(KERN_ERR "PCI: Device %s not available because of resource collisions\n", pci_name(dev));
+			return -EINVAL;
+		}
+		if (r->flags & IORESOURCE_IO)
+			cmd |= PCI_COMMAND_IO;
+		if (r->flags & IORESOURCE_MEM)
+			cmd |= PCI_COMMAND_MEMORY;
+	}
+	if (dev->resource[PCI_ROM_RESOURCE].start)
+		cmd |= PCI_COMMAND_MEMORY;
+	if (cmd != old_cmd) {
+		printk("PCI: Enabling device %s (%04x -> %04x)\n", pci_name(dev), old_cmd, cmd);
+		pci_write_config_word(dev, PCI_COMMAND, cmd);
+	}
+	return 0;
+}
+
+static int next_controller_index;
+
+struct pci_controller * __init
+pcibios_alloc_controller(void)
+{
+	struct pci_controller *hose;
+
+	hose = (struct pci_controller *)alloc_bootmem(sizeof(*hose));
+	memset(hose, 0, sizeof(struct pci_controller));
+
+	*hose_tail = hose;
+	hose_tail = &hose->next;
+
+	hose->index = next_controller_index++;
+
+	return hose;
+}
+
+#ifdef CONFIG_PPC_OF
+/*
+ * Functions below are used on OpenFirmware machines.
+ */
+static void
+make_one_node_map(struct device_node* node, u8 pci_bus)
+{
+	int *bus_range;
+	int len;
+
+	if (pci_bus >= pci_bus_count)
+		return;
+	bus_range = (int *) get_property(node, "bus-range", &len);
+	if (bus_range == NULL || len < 2 * sizeof(int)) {
+		printk(KERN_WARNING "Can't get bus-range for %s, "
+		       "assuming it starts at 0\n", node->full_name);
+		pci_to_OF_bus_map[pci_bus] = 0;
+	} else
+		pci_to_OF_bus_map[pci_bus] = bus_range[0];
+
+	for (node=node->child; node != 0;node = node->sibling) {
+		struct pci_dev* dev;
+		unsigned int *class_code, *reg;
+	
+		class_code = (unsigned int *) get_property(node, "class-code", NULL);
+		if (!class_code || ((*class_code >> 8) != PCI_CLASS_BRIDGE_PCI &&
+			(*class_code >> 8) != PCI_CLASS_BRIDGE_CARDBUS))
+			continue;
+		reg = (unsigned int *)get_property(node, "reg", NULL);
+		if (!reg)
+			continue;
+		dev = pci_find_slot(pci_bus, ((reg[0] >> 8) & 0xff));
+		if (!dev || !dev->subordinate)
+			continue;
+		make_one_node_map(node, dev->subordinate->number);
+	}
+}
+	
+void
+pcibios_make_OF_bus_map(void)
+{
+	int i;
+	struct pci_controller* hose;
+	u8* of_prop_map;
+
+	pci_to_OF_bus_map = (u8*)kmalloc(pci_bus_count, GFP_KERNEL);
+	if (!pci_to_OF_bus_map) {
+		printk(KERN_ERR "Can't allocate OF bus map !\n");
+		return;
+	}
+
+	/* We fill the bus map with invalid values, that helps
+	 * debugging.
+	 */
+	for (i=0; i<pci_bus_count; i++)
+		pci_to_OF_bus_map[i] = 0xff;
+
+	/* For each hose, we begin searching bridges */
+	for(hose=hose_head; hose; hose=hose->next) {
+		struct device_node* node;	
+		node = (struct device_node *)hose->arch_data;
+		if (!node)
+			continue;
+		make_one_node_map(node, hose->first_busno);
+	}
+	of_prop_map = get_property(find_path_device("/"), "pci-OF-bus-map", NULL);
+	if (of_prop_map)
+		memcpy(of_prop_map, pci_to_OF_bus_map, pci_bus_count);
+#ifdef DEBUG
+	printk("PCI->OF bus map:\n");
+	for (i=0; i<pci_bus_count; i++) {
+		if (pci_to_OF_bus_map[i] == 0xff)
+			continue;
+		printk("%d -> %d\n", i, pci_to_OF_bus_map[i]);
+	}
+#endif
+}
+
+typedef int (*pci_OF_scan_iterator)(struct device_node* node, void* data);
+
+static struct device_node*
+scan_OF_pci_childs(struct device_node* node, pci_OF_scan_iterator filter, void* data)
+{
+	struct device_node* sub_node;
+
+	for (; node != 0;node = node->sibling) {
+		unsigned int *class_code;
+	
+		if (filter(node, data))
+			return node;
+
+		/* For PCI<->PCI bridges or CardBus bridges, we go down
+		 * Note: some OFs create a parent node "multifunc-device" as
+		 * a fake root for all functions of a multi-function device,
+		 * we go down them as well.
+		 */
+		class_code = (unsigned int *) get_property(node, "class-code", NULL);
+		if ((!class_code || ((*class_code >> 8) != PCI_CLASS_BRIDGE_PCI &&
+			(*class_code >> 8) != PCI_CLASS_BRIDGE_CARDBUS)) &&
+			strcmp(node->name, "multifunc-device"))
+			continue;
+		sub_node = scan_OF_pci_childs(node->child, filter, data);
+		if (sub_node)
+			return sub_node;
+	}
+	return NULL;
+}
+
+static int
+scan_OF_pci_childs_iterator(struct device_node* node, void* data)
+{
+	unsigned int *reg;
+	u8* fdata = (u8*)data;
+	
+	reg = (unsigned int *) get_property(node, "reg", NULL);
+	if (reg && ((reg[0] >> 8) & 0xff) == fdata[1]
+		&& ((reg[0] >> 16) & 0xff) == fdata[0])
+		return 1;
+	return 0;
+}
+
+static struct device_node*
+scan_OF_childs_for_device(struct device_node* node, u8 bus, u8 dev_fn)
+{
+	u8 filter_data[2] = {bus, dev_fn};
+
+	return scan_OF_pci_childs(node, scan_OF_pci_childs_iterator, filter_data);
+}
+
+/*
+ * Scans the OF tree for a device node matching a PCI device
+ */
+struct device_node *
+pci_busdev_to_OF_node(struct pci_bus *bus, int devfn)
+{
+	struct pci_controller *hose;
+	struct device_node *node;
+	int busnr;
+
+	if (!have_of)
+		return NULL;
+	
+	/* Lookup the hose */
+	busnr = bus->number;
+	hose = pci_bus_to_hose(busnr);
+	if (!hose)
+		return NULL;
+
+	/* Check it has an OF node associated */
+	node = (struct device_node *) hose->arch_data;
+	if (!node)
+		return NULL;
+
+	/* Fixup bus number according to what OF think it is. */
+#ifdef CONFIG_PPC_PMAC
+	/* The G5 need a special case here. Basically, we don't remap all
+	 * busses on it so we don't create the pci-OF-map. However, we do
+	 * remap the AGP bus and so have to deal with it. A future better
+	 * fix has to be done by making the remapping per-host and always
+	 * filling the pci_to_OF map. --BenH
+	 */
+	if (_machine == _MACH_Pmac && busnr >= 0xf0)
+		busnr -= 0xf0;
+	else
+#endif
+	if (pci_to_OF_bus_map)
+		busnr = pci_to_OF_bus_map[busnr];
+	if (busnr == 0xff)
+		return NULL;
+	
+	/* Now, lookup childs of the hose */
+	return scan_OF_childs_for_device(node->child, busnr, devfn);
+}
+EXPORT_SYMBOL(pci_busdev_to_OF_node);
+
+struct device_node*
+pci_device_to_OF_node(struct pci_dev *dev)
+{
+	return pci_busdev_to_OF_node(dev->bus, dev->devfn);
+}
+EXPORT_SYMBOL(pci_device_to_OF_node);
+
+/* This routine is meant to be used early during boot, when the
+ * PCI bus numbers have not yet been assigned, and you need to
+ * issue PCI config cycles to an OF device.
+ * It could also be used to "fix" RTAS config cycles if you want
+ * to set pci_assign_all_buses to 1 and still use RTAS for PCI
+ * config cycles.
+ */
+struct pci_controller* pci_find_hose_for_OF_device(struct device_node* node)
+{
+	if (!have_of)
+		return NULL;
+	while(node) {
+		struct pci_controller* hose;
+		for (hose=hose_head;hose;hose=hose->next)
+			if (hose->arch_data == node)
+				return hose;
+		node=node->parent;
+	}
+	return NULL;
+}
+
+static int
+find_OF_pci_device_filter(struct device_node* node, void* data)
+{
+	return ((void *)node == data);
+}
+
+/*
+ * Returns the PCI device matching a given OF node
+ */
+int
+pci_device_from_OF_node(struct device_node* node, u8* bus, u8* devfn)
+{
+	unsigned int *reg;
+	struct pci_controller* hose;
+	struct pci_dev* dev = NULL;
+	
+	if (!have_of)
+		return -ENODEV;
+	/* Make sure it's really a PCI device */
+	hose = pci_find_hose_for_OF_device(node);
+	if (!hose || !hose->arch_data)
+		return -ENODEV;
+	if (!scan_OF_pci_childs(((struct device_node*)hose->arch_data)->child,
+			find_OF_pci_device_filter, (void *)node))
+		return -ENODEV;
+	reg = (unsigned int *) get_property(node, "reg", NULL);
+	if (!reg)
+		return -ENODEV;
+	*bus = (reg[0] >> 16) & 0xff;
+	*devfn = ((reg[0] >> 8) & 0xff);
+
+	/* Ok, here we need some tweak. If we have already renumbered
+	 * all busses, we can't rely on the OF bus number any more.
+	 * the pci_to_OF_bus_map is not enough as several PCI busses
+	 * may match the same OF bus number.
+	 */
+	if (!pci_to_OF_bus_map)
+		return 0;
+
+	for_each_pci_dev(dev)
+		if (pci_to_OF_bus_map[dev->bus->number] == *bus &&
+				dev->devfn == *devfn) {
+			*bus = dev->bus->number;
+			pci_dev_put(dev);
+			return 0;
+		}
+
+	return -ENODEV;
+}
+EXPORT_SYMBOL(pci_device_from_OF_node);
+
+void __init
+pci_process_bridge_OF_ranges(struct pci_controller *hose,
+			   struct device_node *dev, int primary)
+{
+	static unsigned int static_lc_ranges[256] __initdata;
+	unsigned int *dt_ranges, *lc_ranges, *ranges, *prev;
+	unsigned int size;
+	int rlen = 0, orig_rlen;
+	int memno = 0;
+	struct resource *res;
+	int np, na = prom_n_addr_cells(dev);
+	np = na + 5;
+
+	/* First we try to merge ranges to fix a problem with some pmacs
+	 * that can have more than 3 ranges, fortunately using contiguous
+	 * addresses -- BenH
+	 */
+	dt_ranges = (unsigned int *) get_property(dev, "ranges", &rlen);
+	if (!dt_ranges)
+		return;
+	/* Sanity check, though hopefully that never happens */
+	if (rlen > sizeof(static_lc_ranges)) {
+		printk(KERN_WARNING "OF ranges property too large !\n");
+		rlen = sizeof(static_lc_ranges);
+	}
+	lc_ranges = static_lc_ranges;
+	memcpy(lc_ranges, dt_ranges, rlen);
+	orig_rlen = rlen;
+
+	/* Let's work on a copy of the "ranges" property instead of damaging
+	 * the device-tree image in memory
+	 */
+	ranges = lc_ranges;
+	prev = NULL;
+	while ((rlen -= np * sizeof(unsigned int)) >= 0) {
+		if (prev) {
+			if (prev[0] == ranges[0] && prev[1] == ranges[1] &&
+				(prev[2] + prev[na+4]) == ranges[2] &&
+				(prev[na+2] + prev[na+4]) == ranges[na+2]) {
+				prev[na+4] += ranges[na+4];
+				ranges[0] = 0;
+				ranges += np;
+				continue;
+			}
+		}
+		prev = ranges;
+		ranges += np;
+	}
+
+	/*
+	 * The ranges property is laid out as an array of elements,
+	 * each of which comprises:
+	 *   cells 0 - 2:	a PCI address
+	 *   cells 3 or 3+4:	a CPU physical address
+	 *			(size depending on dev->n_addr_cells)
+	 *   cells 4+5 or 5+6:	the size of the range
+	 */
+	ranges = lc_ranges;
+	rlen = orig_rlen;
+	while (ranges && (rlen -= np * sizeof(unsigned int)) >= 0) {
+		res = NULL;
+		size = ranges[na+4];
+		switch ((ranges[0] >> 24) & 0x3) {
+		case 1:		/* I/O space */
+			if (ranges[2] != 0)
+				break;
+			hose->io_base_phys = ranges[na+2];
+			/* limit I/O space to 16MB */
+			if (size > 0x01000000)
+				size = 0x01000000;
+			hose->io_base_virt = ioremap(ranges[na+2], size);
+			if (primary)
+				isa_io_base = (unsigned long) hose->io_base_virt;
+			res = &hose->io_resource;
+			res->flags = IORESOURCE_IO;
+			res->start = ranges[2];
+			DBG("PCI: IO 0x%lx -> 0x%lx\n",
+				    res->start, res->start + size - 1);
+			break;
+		case 2:		/* memory space */
+			memno = 0;
+			if (ranges[1] == 0 && ranges[2] == 0
+			    && ranges[na+4] <= (16 << 20)) {
+				/* 1st 16MB, i.e. ISA memory area */
+				if (primary)
+					isa_mem_base = ranges[na+2];
+				memno = 1;
+			}
+			while (memno < 3 && hose->mem_resources[memno].flags)
+				++memno;
+			if (memno == 0)
+				hose->pci_mem_offset = ranges[na+2] - ranges[2];
+			if (memno < 3) {
+				res = &hose->mem_resources[memno];
+				res->flags = IORESOURCE_MEM;
+				if(ranges[0] & 0x40000000)
+					res->flags |= IORESOURCE_PREFETCH;
+				res->start = ranges[na+2];
+				DBG("PCI: MEM[%d] 0x%lx -> 0x%lx\n", memno,
+					    res->start, res->start + size - 1);
+			}
+			break;
+		}
+		if (res != NULL) {
+			res->name = dev->full_name;
+			res->end = res->start + size - 1;
+			res->parent = NULL;
+			res->sibling = NULL;
+			res->child = NULL;
+		}
+		ranges += np;
+	}
+}
+
+/* We create the "pci-OF-bus-map" property now so it appears in the
+ * /proc device tree
+ */
+void __init
+pci_create_OF_bus_map(void)
+{
+	struct property* of_prop;
+	
+	of_prop = (struct property*) alloc_bootmem(sizeof(struct property) + 256);
+	if (of_prop && find_path_device("/")) {
+		memset(of_prop, -1, sizeof(struct property) + 256);
+		of_prop->name = "pci-OF-bus-map";
+		of_prop->length = 256;
+		of_prop->value = (unsigned char *)&of_prop[1];
+		prom_add_property(find_path_device("/"), of_prop);
+	}
+}
+
+static ssize_t pci_show_devspec(struct device *dev, struct device_attribute *attr, char *buf)
+{
+	struct pci_dev *pdev;
+	struct device_node *np;
+
+	pdev = to_pci_dev (dev);
+	np = pci_device_to_OF_node(pdev);
+	if (np == NULL || np->full_name == NULL)
+		return 0;
+	return sprintf(buf, "%s", np->full_name);
+}
+static DEVICE_ATTR(devspec, S_IRUGO, pci_show_devspec, NULL);
+
+#else /* CONFIG_PPC_OF */
+void pcibios_make_OF_bus_map(void)
+{
+}
+#endif /* CONFIG_PPC_OF */
+
+/* Add sysfs properties */
+void pcibios_add_platform_entries(struct pci_dev *pdev)
+{
+#ifdef CONFIG_PPC_OF
+	device_create_file(&pdev->dev, &dev_attr_devspec);
+#endif /* CONFIG_PPC_OF */
+}
+
+
+#ifdef CONFIG_PPC_PMAC
+/*
+ * This set of routines checks for PCI<->PCI bridges that have closed
+ * IO resources and have child devices. It tries to re-open an IO
+ * window on them.
+ *
+ * This is a _temporary_ fix to workaround a problem with Apple's OF
+ * closing IO windows on P2P bridges when the OF drivers of cards
+ * below this bridge don't claim any IO range (typically ATI or
+ * Adaptec).
+ *
+ * A more complete fix would be to use drivers/pci/setup-bus.c, which
+ * involves a working pcibios_fixup_pbus_ranges(), some more care about
+ * ordering when creating the host bus resources, and maybe a few more
+ * minor tweaks
+ */
+
+/* Initialize bridges with base/limit values we have collected */
+static void __init
+do_update_p2p_io_resource(struct pci_bus *bus, int enable_vga)
+{
+	struct pci_dev *bridge = bus->self;
+	struct pci_controller* hose = (struct pci_controller *)bridge->sysdata;
+	u32 l;
+	u16 w;
+	struct resource res;
+
+	if (bus->resource[0] == NULL)
+		return;
+ 	res = *(bus->resource[0]);
+
+	DBG("Remapping Bus %d, bridge: %s\n", bus->number, pci_name(bridge));
+	res.start -= ((unsigned long) hose->io_base_virt - isa_io_base);
+	res.end -= ((unsigned long) hose->io_base_virt - isa_io_base);
+	DBG("  IO window: %08lx-%08lx\n", res.start, res.end);
+
+	/* Set up the top and bottom of the PCI I/O segment for this bus. */
+	pci_read_config_dword(bridge, PCI_IO_BASE, &l);
+	l &= 0xffff000f;
+	l |= (res.start >> 8) & 0x00f0;
+	l |= res.end & 0xf000;
+	pci_write_config_dword(bridge, PCI_IO_BASE, l);
+
+	if ((l & PCI_IO_RANGE_TYPE_MASK) == PCI_IO_RANGE_TYPE_32) {
+		l = (res.start >> 16) | (res.end & 0xffff0000);
+		pci_write_config_dword(bridge, PCI_IO_BASE_UPPER16, l);
+	}
+
+	pci_read_config_word(bridge, PCI_COMMAND, &w);
+	w |= PCI_COMMAND_IO;
+	pci_write_config_word(bridge, PCI_COMMAND, w);
+
+#if 0 /* Enabling this causes XFree 4.2.0 to hang during PCI probe */
+	if (enable_vga) {
+		pci_read_config_word(bridge, PCI_BRIDGE_CONTROL, &w);
+		w |= PCI_BRIDGE_CTL_VGA;
+		pci_write_config_word(bridge, PCI_BRIDGE_CONTROL, w);
+	}
+#endif
+}
+
+/* This function is pretty basic and actually quite broken for the
+ * general case, it's enough for us right now though. It's supposed
+ * to tell us if we need to open an IO range at all or not and what
+ * size.
+ */
+static int __init
+check_for_io_childs(struct pci_bus *bus, struct resource* res, int *found_vga)
+{
+	struct pci_dev *dev;
+	int	i;
+	int	rc = 0;
+
+#define push_end(res, size) do { unsigned long __sz = (size) ; \
+	res->end = ((res->end + __sz) / (__sz + 1)) * (__sz + 1) + __sz; \
+    } while (0)
+
+	list_for_each_entry(dev, &bus->devices, bus_list) {
+		u16 class = dev->class >> 8;
+
+		if (class == PCI_CLASS_DISPLAY_VGA ||
+		    class == PCI_CLASS_NOT_DEFINED_VGA)
+			*found_vga = 1;
+		if (class >> 8 == PCI_BASE_CLASS_BRIDGE && dev->subordinate)
+			rc |= check_for_io_childs(dev->subordinate, res, found_vga);
+		if (class == PCI_CLASS_BRIDGE_CARDBUS)
+			push_end(res, 0xfff);
+
+		for (i=0; i<PCI_NUM_RESOURCES; i++) {
+			struct resource *r;
+			unsigned long r_size;
+
+			if (dev->class >> 8 == PCI_CLASS_BRIDGE_PCI
+			    && i >= PCI_BRIDGE_RESOURCES)
+				continue;
+			r = &dev->resource[i];
+			r_size = r->end - r->start;
+			if (r_size < 0xfff)
+				r_size = 0xfff;
+			if (r->flags & IORESOURCE_IO && (r_size) != 0) {
+				rc = 1;
+				push_end(res, r_size);
+			}
+		}
+	}
+
+	return rc;
+}
+
+/* Here we scan all P2P bridges of a given level that have a closed
+ * IO window. Note that the test for the presence of a VGA card should
+ * be improved to take into account already configured P2P bridges,
+ * currently, we don't see them and might end up configuring 2 bridges
+ * with VGA pass through enabled
+ */
+static void __init
+do_fixup_p2p_level(struct pci_bus *bus)
+{
+	struct pci_bus *b;
+	int i, parent_io;
+	int has_vga = 0;
+
+	for (parent_io=0; parent_io<4; parent_io++)
+		if (bus->resource[parent_io]
+		    && bus->resource[parent_io]->flags & IORESOURCE_IO)
+			break;
+	if (parent_io >= 4)
+		return;
+
+	list_for_each_entry(b, &bus->children, node) {
+		struct pci_dev *d = b->self;
+		struct pci_controller* hose = (struct pci_controller *)d->sysdata;
+		struct resource *res = b->resource[0];
+		struct resource tmp_res;
+		unsigned long max;
+		int found_vga = 0;
+
+		memset(&tmp_res, 0, sizeof(tmp_res));
+		tmp_res.start = bus->resource[parent_io]->start;
+
+		/* We don't let low addresses go through that closed P2P bridge, well,
+		 * that may not be necessary but I feel safer that way
+		 */
+		if (tmp_res.start == 0)
+			tmp_res.start = 0x1000;
+	
+		if (!list_empty(&b->devices) && res && res->flags == 0 &&
+		    res != bus->resource[parent_io] &&
+		    (d->class >> 8) == PCI_CLASS_BRIDGE_PCI &&
+		    check_for_io_childs(b, &tmp_res, &found_vga)) {
+			u8 io_base_lo;
+
+			printk(KERN_INFO "Fixing up IO bus %s\n", b->name);
+
+			if (found_vga) {
+				if (has_vga) {
+					printk(KERN_WARNING "Skipping VGA, already active"
+					    " on bus segment\n");
+					found_vga = 0;
+				} else
+					has_vga = 1;
+			}
+			pci_read_config_byte(d, PCI_IO_BASE, &io_base_lo);
+
+			if ((io_base_lo & PCI_IO_RANGE_TYPE_MASK) == PCI_IO_RANGE_TYPE_32)
+				max = ((unsigned long) hose->io_base_virt
+					- isa_io_base) + 0xffffffff;
+			else
+				max = ((unsigned long) hose->io_base_virt
+					- isa_io_base) + 0xffff;
+
+			*res = tmp_res;
+			res->flags = IORESOURCE_IO;
+			res->name = b->name;
+		
+			/* Find a resource in the parent where we can allocate */
+			for (i = 0 ; i < 4; i++) {
+				struct resource *r = bus->resource[i];
+				if (!r)
+					continue;
+				if ((r->flags & IORESOURCE_IO) == 0)
+					continue;
+				DBG("Trying to allocate from %08lx, size %08lx from parent"
+				    " res %d: %08lx -> %08lx\n",
+					res->start, res->end, i, r->start, r->end);
+			
+				if (allocate_resource(r, res, res->end + 1, res->start, max,
+				    res->end + 1, NULL, NULL) < 0) {
+					DBG("Failed !\n");
+					continue;
+				}
+				do_update_p2p_io_resource(b, found_vga);
+				break;
+			}
+		}
+		do_fixup_p2p_level(b);
+	}
+}
+
+static void
+pcibios_fixup_p2p_bridges(void)
+{
+	struct pci_bus *b;
+
+	list_for_each_entry(b, &pci_root_buses, node)
+		do_fixup_p2p_level(b);
+}
+
+#endif /* CONFIG_PPC_PMAC */
+
+static int __init
+pcibios_init(void)
+{
+	struct pci_controller *hose;
+	struct pci_bus *bus;
+	int next_busno;
+
+	printk(KERN_INFO "PCI: Probing PCI hardware\n");
+
+	/* Scan all of the recorded PCI controllers.  */
+	for (next_busno = 0, hose = hose_head; hose; hose = hose->next) {
+		if (pci_assign_all_buses)
+			hose->first_busno = next_busno;
+		hose->last_busno = 0xff;
+		bus = pci_scan_bus(hose->first_busno, hose->ops, hose);
+		hose->last_busno = bus->subordinate;
+		if (pci_assign_all_buses || next_busno <= hose->last_busno)
+			next_busno = hose->last_busno + pcibios_assign_bus_offset;
+	}
+	pci_bus_count = next_busno;
+
+	/* OpenFirmware based machines need a map of OF bus
+	 * numbers vs. kernel bus numbers since we may have to
+	 * remap them.
+	 */
+	if (pci_assign_all_buses && have_of)
+		pcibios_make_OF_bus_map();
+
+	/* Do machine dependent PCI interrupt routing */
+	if (ppc_md.pci_swizzle && ppc_md.pci_map_irq)
+		pci_fixup_irqs(ppc_md.pci_swizzle, ppc_md.pci_map_irq);
+
+	/* Call machine dependent fixup */
+	if (ppc_md.pcibios_fixup)
+		ppc_md.pcibios_fixup();
+
+	/* Allocate and assign resources */
+	pcibios_allocate_bus_resources(&pci_root_buses);
+	pcibios_allocate_resources(0);
+	pcibios_allocate_resources(1);
+#ifdef CONFIG_PPC_PMAC
+	pcibios_fixup_p2p_bridges();
+#endif /* CONFIG_PPC_PMAC */
+	pcibios_assign_resources();
+
+	/* Call machine dependent post-init code */
+	if (ppc_md.pcibios_after_init)
+		ppc_md.pcibios_after_init();
+
+	return 0;
+}
+
+subsys_initcall(pcibios_init);
+
+unsigned char __init
+common_swizzle(struct pci_dev *dev, unsigned char *pinp)
+{
+	struct pci_controller *hose = dev->sysdata;
+
+	if (dev->bus->number != hose->first_busno) {
+		u8 pin = *pinp;
+		do {
+			pin = bridge_swizzle(pin, PCI_SLOT(dev->devfn));
+			/* Move up the chain of bridges. */
+			dev = dev->bus->self;
+		} while (dev->bus->self);
+		*pinp = pin;
+
+		/* The slot is the idsel of the last bridge. */
+	}
+	return PCI_SLOT(dev->devfn);
+}
+
+unsigned long resource_fixup(struct pci_dev * dev, struct resource * res,
+			     unsigned long start, unsigned long size)
+{
+	return start;
+}
+
+void __init pcibios_fixup_bus(struct pci_bus *bus)
+{
+	struct pci_controller *hose = (struct pci_controller *) bus->sysdata;
+	unsigned long io_offset;
+	struct resource *res;
+	int i;
+
+	io_offset = (unsigned long)hose->io_base_virt - isa_io_base;
+	if (bus->parent == NULL) {
+		/* This is a host bridge - fill in its resources */
+		hose->bus = bus;
+
+		bus->resource[0] = res = &hose->io_resource;
+		if (!res->flags) {
+			if (io_offset)
+				printk(KERN_ERR "I/O resource not set for host"
+				       " bridge %d\n", hose->index);
+			res->start = 0;
+			res->end = IO_SPACE_LIMIT;
+			res->flags = IORESOURCE_IO;
+		}
+		res->start += io_offset;
+		res->end += io_offset;
+
+		for (i = 0; i < 3; ++i) {
+			res = &hose->mem_resources[i];
+			if (!res->flags) {
+				if (i > 0)
+					continue;
+				printk(KERN_ERR "Memory resource not set for "
+				       "host bridge %d\n", hose->index);
+				res->start = hose->pci_mem_offset;
+				res->end = ~0U;
+				res->flags = IORESOURCE_MEM;
+			}
+			bus->resource[i+1] = res;
+		}
+	} else {
+		/* This is a subordinate bridge */
+		pci_read_bridge_bases(bus);
+
+		for (i = 0; i < 4; ++i) {
+			if ((res = bus->resource[i]) == NULL)
+				continue;
+			if (!res->flags)
+				continue;
+			if (io_offset && (res->flags & IORESOURCE_IO)) {
+				res->start += io_offset;
+				res->end += io_offset;
+			} else if (hose->pci_mem_offset
+				   && (res->flags & IORESOURCE_MEM)) {
+				res->start += hose->pci_mem_offset;
+				res->end += hose->pci_mem_offset;
+			}
+		}
+	}
+
+	if (ppc_md.pcibios_fixup_bus)
+		ppc_md.pcibios_fixup_bus(bus);
+}
+
+char __init *pcibios_setup(char *str)
+{
+	return str;
+}
+
+/* the next one is stolen from the alpha port... */
+void __init
+pcibios_update_irq(struct pci_dev *dev, int irq)
+{
+	pci_write_config_byte(dev, PCI_INTERRUPT_LINE, irq);
+	/* XXX FIXME - update OF device tree node interrupt property */
+}
+
+int pcibios_enable_device(struct pci_dev *dev, int mask)
+{
+	u16 cmd, old_cmd;
+	int idx;
+	struct resource *r;
+
+	if (ppc_md.pcibios_enable_device_hook)
+		if (ppc_md.pcibios_enable_device_hook(dev, 0))
+			return -EINVAL;
+		
+	pci_read_config_word(dev, PCI_COMMAND, &cmd);
+	old_cmd = cmd;
+	for (idx=0; idx<6; idx++) {
+		r = &dev->resource[idx];
+		if (r->flags & IORESOURCE_UNSET) {
+			printk(KERN_ERR "PCI: Device %s not available because of resource collisions\n", pci_name(dev));
+			return -EINVAL;
+		}
+		if (r->flags & IORESOURCE_IO)
+			cmd |= PCI_COMMAND_IO;
+		if (r->flags & IORESOURCE_MEM)
+			cmd |= PCI_COMMAND_MEMORY;
+	}
+	if (cmd != old_cmd) {
+		printk("PCI: Enabling device %s (%04x -> %04x)\n",
+		       pci_name(dev), old_cmd, cmd);
+		pci_write_config_word(dev, PCI_COMMAND, cmd);
+	}
+	return 0;
+}
+
+struct pci_controller*
+pci_bus_to_hose(int bus)
+{
+	struct pci_controller* hose = hose_head;
+
+	for (; hose; hose = hose->next)
+		if (bus >= hose->first_busno && bus <= hose->last_busno)
+			return hose;
+	return NULL;
+}
+
+void __iomem *
+pci_bus_io_base(unsigned int bus)
+{
+	struct pci_controller *hose;
+
+	hose = pci_bus_to_hose(bus);
+	if (!hose)
+		return NULL;
+	return hose->io_base_virt;
+}
+
+unsigned long
+pci_bus_io_base_phys(unsigned int bus)
+{
+	struct pci_controller *hose;
+
+	hose = pci_bus_to_hose(bus);
+	if (!hose)
+		return 0;
+	return hose->io_base_phys;
+}
+
+unsigned long
+pci_bus_mem_base_phys(unsigned int bus)
+{
+	struct pci_controller *hose;
+
+	hose = pci_bus_to_hose(bus);
+	if (!hose)
+		return 0;
+	return hose->pci_mem_offset;
+}
+
+unsigned long
+pci_resource_to_bus(struct pci_dev *pdev, struct resource *res)
+{
+	/* Hack alert again ! See comments in chrp_pci.c
+	 */
+	struct pci_controller* hose =
+		(struct pci_controller *)pdev->sysdata;
+	if (hose && res->flags & IORESOURCE_MEM)
+		return res->start - hose->pci_mem_offset;
+	/* We may want to do something with IOs here... */
+	return res->start;
+}
+
+
+static struct resource *__pci_mmap_make_offset(struct pci_dev *dev,
+					       unsigned long *offset,
+					       enum pci_mmap_state mmap_state)
+{
+	struct pci_controller *hose = pci_bus_to_hose(dev->bus->number);
+	unsigned long io_offset = 0;
+	int i, res_bit;
+
+	if (hose == 0)
+		return NULL;		/* should never happen */
+
+	/* If memory, add on the PCI bridge address offset */
+	if (mmap_state == pci_mmap_mem) {
+		*offset += hose->pci_mem_offset;
+		res_bit = IORESOURCE_MEM;
+	} else {
+		io_offset = hose->io_base_virt - ___IO_BASE;
+		*offset += io_offset;
+		res_bit = IORESOURCE_IO;
+	}
+
+	/*
+	 * Check that the offset requested corresponds to one of the
+	 * resources of the device.
+	 */
+	for (i = 0; i <= PCI_ROM_RESOURCE; i++) {
+		struct resource *rp = &dev->resource[i];
+		int flags = rp->flags;
+
+		/* treat ROM as memory (should be already) */
+		if (i == PCI_ROM_RESOURCE)
+			flags |= IORESOURCE_MEM;
+
+		/* Active and same type? */
+		if ((flags & res_bit) == 0)
+			continue;
+
+		/* In the range of this resource? */
+		if (*offset < (rp->start & PAGE_MASK) || *offset > rp->end)
+			continue;
+
+		/* found it! construct the final physical address */
+		if (mmap_state == pci_mmap_io)
+			*offset += hose->io_base_phys - io_offset;
+		return rp;
+	}
+
+	return NULL;
+}
+
+/*
+ * Set vm_page_prot of VMA, as appropriate for this architecture, for a pci
+ * device mapping.
+ */
+static pgprot_t __pci_mmap_set_pgprot(struct pci_dev *dev, struct resource *rp,
+				      pgprot_t protection,
+				      enum pci_mmap_state mmap_state,
+				      int write_combine)
+{
+	unsigned long prot = pgprot_val(protection);
+
+	/* Write combine is always 0 on non-memory space mappings. On
+	 * memory space, if the user didn't pass 1, we check for a
+	 * "prefetchable" resource. This is a bit hackish, but we use
+	 * this to workaround the inability of /sysfs to provide a write
+	 * combine bit
+	 */
+	if (mmap_state != pci_mmap_mem)
+		write_combine = 0;
+	else if (write_combine == 0) {
+		if (rp->flags & IORESOURCE_PREFETCH)
+			write_combine = 1;
+	}
+
+	/* XXX would be nice to have a way to ask for write-through */
+	prot |= _PAGE_NO_CACHE;
+	if (write_combine)
+		prot &= ~_PAGE_GUARDED;
+	else
+		prot |= _PAGE_GUARDED;
+
+	printk("PCI map for %s:%lx, prot: %lx\n", pci_name(dev), rp->start,
+	       prot);
+
+	return __pgprot(prot);
+}
+
+/*
+ * This one is used by /dev/mem and fbdev who have no clue about the
+ * PCI device, it tries to find the PCI device first and calls the
+ * above routine
+ */
+pgprot_t pci_phys_mem_access_prot(struct file *file,
+				  unsigned long pfn,
+				  unsigned long size,
+				  pgprot_t protection)
+{
+	struct pci_dev *pdev = NULL;
+	struct resource *found = NULL;
+	unsigned long prot = pgprot_val(protection);
+	unsigned long offset = pfn << PAGE_SHIFT;
+	int i;
+
+	if (page_is_ram(pfn))
+		return prot;
+
+	prot |= _PAGE_NO_CACHE | _PAGE_GUARDED;
+
+	for_each_pci_dev(pdev) {
+		for (i = 0; i <= PCI_ROM_RESOURCE; i++) {
+			struct resource *rp = &pdev->resource[i];
+			int flags = rp->flags;
+
+			/* Active and same type? */
+			if ((flags & IORESOURCE_MEM) == 0)
+				continue;
+			/* In the range of this resource? */
+			if (offset < (rp->start & PAGE_MASK) ||
+			    offset > rp->end)
+				continue;
+			found = rp;
+			break;
+		}
+		if (found)
+			break;
+	}
+	if (found) {
+		if (found->flags & IORESOURCE_PREFETCH)
+			prot &= ~_PAGE_GUARDED;
+		pci_dev_put(pdev);
+	}
+
+	DBG("non-PCI map for %lx, prot: %lx\n", offset, prot);
+
+	return __pgprot(prot);
+}
+
+
+/*
+ * Perform the actual remap of the pages for a PCI device mapping, as
+ * appropriate for this architecture.  The region in the process to map
+ * is described by vm_start and vm_end members of VMA, the base physical
+ * address is found in vm_pgoff.
+ * The pci device structure is provided so that architectures may make mapping
+ * decisions on a per-device or per-bus basis.
+ *
+ * Returns a negative error code on failure, zero on success.
+ */
+int pci_mmap_page_range(struct pci_dev *dev, struct vm_area_struct *vma,
+			enum pci_mmap_state mmap_state,
+			int write_combine)
+{
+	unsigned long offset = vma->vm_pgoff << PAGE_SHIFT;
+	struct resource *rp;
+	int ret;
+
+	rp = __pci_mmap_make_offset(dev, &offset, mmap_state);
+	if (rp == NULL)
+		return -EINVAL;
+
+	vma->vm_pgoff = offset >> PAGE_SHIFT;
+	vma->vm_flags |= VM_SHM | VM_LOCKED | VM_IO;
+	vma->vm_page_prot = __pci_mmap_set_pgprot(dev, rp,
+						  vma->vm_page_prot,
+						  mmap_state, write_combine);
+
+	ret = remap_pfn_range(vma, vma->vm_start, vma->vm_pgoff,
+			       vma->vm_end - vma->vm_start, vma->vm_page_prot);
+
+	return ret;
+}
+
+/* Obsolete functions. Should be removed once the symbios driver
+ * is fixed
+ */
+unsigned long
+phys_to_bus(unsigned long pa)
+{
+	struct pci_controller *hose;
+	int i;
+
+	for (hose = hose_head; hose; hose = hose->next) {
+		for (i = 0; i < 3; ++i) {
+			if (pa >= hose->mem_resources[i].start
+			    && pa <= hose->mem_resources[i].end) {
+				/*
+				 * XXX the hose->pci_mem_offset really
+				 * only applies to mem_resources[0].
+				 * We need a way to store an offset for
+				 * the others.  -- paulus
+				 */
+				if (i == 0)
+					pa -= hose->pci_mem_offset;
+				return pa;
+			}
+		}
+	}
+	/* hmmm, didn't find it */
+	return 0;
+}
+
+unsigned long
+pci_phys_to_bus(unsigned long pa, int busnr)
+{
+	struct pci_controller* hose = pci_bus_to_hose(busnr);
+	if (!hose)
+		return pa;
+	return pa - hose->pci_mem_offset;
+}
+
+unsigned long
+pci_bus_to_phys(unsigned int ba, int busnr)
+{
+	struct pci_controller* hose = pci_bus_to_hose(busnr);
+	if (!hose)
+		return ba;
+	return ba + hose->pci_mem_offset;
+}
+
+/* Provide information on locations of various I/O regions in physical
+ * memory.  Do this on a per-card basis so that we choose the right
+ * root bridge.
+ * Note that the returned IO or memory base is a physical address
+ */
+
+long sys_pciconfig_iobase(long which, unsigned long bus, unsigned long devfn)
+{
+	struct pci_controller* hose;
+	long result = -EOPNOTSUPP;
+
+	/* Argh ! Please forgive me for that hack, but that's the
+	 * simplest way to get existing XFree to not lockup on some
+	 * G5 machines... So when something asks for bus 0 io base
+	 * (bus 0 is HT root), we return the AGP one instead.
+	 */
+#ifdef CONFIG_PPC_PMAC
+	if (_machine == _MACH_Pmac && machine_is_compatible("MacRISC4"))
+		if (bus == 0)
+			bus = 0xf0;
+#endif /* CONFIG_PPC_PMAC */
+
+	hose = pci_bus_to_hose(bus);
+	if (!hose)
+		return -ENODEV;
+
+	switch (which) {
+	case IOBASE_BRIDGE_NUMBER:
+		return (long)hose->first_busno;
+	case IOBASE_MEMORY:
+		return (long)hose->pci_mem_offset;
+	case IOBASE_IO:
+		return (long)hose->io_base_phys;
+	case IOBASE_ISA_IO:
+		return (long)isa_io_base;
+	case IOBASE_ISA_MEM:
+		return (long)isa_mem_base;
+	}
+
+	return result;
+}
+
+void pci_resource_to_user(const struct pci_dev *dev, int bar,
+			  const struct resource *rsrc,
+			  u64 *start, u64 *end)
+{
+	struct pci_controller *hose = pci_bus_to_hose(dev->bus->number);
+	unsigned long offset = 0;
+
+	if (hose == NULL)
+		return;
+
+	if (rsrc->flags & IORESOURCE_IO)
+		offset = ___IO_BASE - hose->io_base_virt + hose->io_base_phys;
+
+	*start = rsrc->start + offset;
+	*end = rsrc->end + offset;
+}
+
+void __init
+pci_init_resource(struct resource *res, unsigned long start, unsigned long end,
+		  int flags, char *name)
+{
+	res->start = start;
+	res->end = end;
+	res->flags = flags;
+	res->name = name;
+	res->parent = NULL;
+	res->sibling = NULL;
+	res->child = NULL;
+}
+
+void __iomem *pci_iomap(struct pci_dev *dev, int bar, unsigned long max)
+{
+	unsigned long start = pci_resource_start(dev, bar);
+	unsigned long len = pci_resource_len(dev, bar);
+	unsigned long flags = pci_resource_flags(dev, bar);
+
+	if (!len)
+		return NULL;
+	if (max && len > max)
+		len = max;
+	if (flags & IORESOURCE_IO)
+		return ioport_map(start, len);
+	if (flags & IORESOURCE_MEM)
+		/* Not checking IORESOURCE_CACHEABLE because PPC does
+		 * not currently distinguish between ioremap and
+		 * ioremap_nocache.
+		 */
+		return ioremap(start, len);
+	/* What? */
+	return NULL;
+}
+
+void pci_iounmap(struct pci_dev *dev, void __iomem *addr)
+{
+	/* Nothing to do */
+}
+EXPORT_SYMBOL(pci_iomap);
+EXPORT_SYMBOL(pci_iounmap);
+
+unsigned long pci_address_to_pio(phys_addr_t address)
+{
+	struct pci_controller* hose = hose_head;
+
+	for (; hose; hose = hose->next) {
+		unsigned int size = hose->io_resource.end -
+			hose->io_resource.start + 1;
+		if (address >= hose->io_base_phys &&
+		    address < (hose->io_base_phys + size)) {
+			unsigned long base =
+				(unsigned long)hose->io_base_virt - _IO_BASE;
+			return base + (address - hose->io_base_phys);
+		}
+	}
+	return (unsigned int)-1;
+}
+EXPORT_SYMBOL(pci_address_to_pio);
+
+/*
+ * Null PCI config access functions, for the case when we can't
+ * find a hose.
+ */
+#define NULL_PCI_OP(rw, size, type)					\
+static int								\
+null_##rw##_config_##size(struct pci_dev *dev, int offset, type val)	\
+{									\
+	return PCIBIOS_DEVICE_NOT_FOUND;    				\
+}
+
+static int
+null_read_config(struct pci_bus *bus, unsigned int devfn, int offset,
+		 int len, u32 *val)
+{
+	return PCIBIOS_DEVICE_NOT_FOUND;
+}
+
+static int
+null_write_config(struct pci_bus *bus, unsigned int devfn, int offset,
+		  int len, u32 val)
+{
+	return PCIBIOS_DEVICE_NOT_FOUND;
+}
+
+static struct pci_ops null_pci_ops =
+{
+	null_read_config,
+	null_write_config
+};
+
+/*
+ * These functions are used early on before PCI scanning is done
+ * and all of the pci_dev and pci_bus structures have been created.
+ */
+static struct pci_bus *
+fake_pci_bus(struct pci_controller *hose, int busnr)
+{
+	static struct pci_bus bus;
+
+	if (hose == 0) {
+		hose = pci_bus_to_hose(busnr);
+		if (hose == 0)
+			printk(KERN_ERR "Can't find hose for PCI bus %d!\n", busnr);
+	}
+	bus.number = busnr;
+	bus.sysdata = hose;
+	bus.ops = hose? hose->ops: &null_pci_ops;
+	return &bus;
+}
+
+#define EARLY_PCI_OP(rw, size, type)					\
+int early_##rw##_config_##size(struct pci_controller *hose, int bus,	\
+			       int devfn, int offset, type value)	\
+{									\
+	return pci_bus_##rw##_config_##size(fake_pci_bus(hose, bus),	\
+					    devfn, offset, value);	\
+}
+
+EARLY_PCI_OP(read, byte, u8 *)
+EARLY_PCI_OP(read, word, u16 *)
+EARLY_PCI_OP(read, dword, u32 *)
+EARLY_PCI_OP(write, byte, u8)
+EARLY_PCI_OP(write, word, u16)
+EARLY_PCI_OP(write, dword, u32)
diff --git a/arch/powerpc/kernel/prom_init.c b/arch/powerpc/kernel/prom_init.c
index d963a12ec64..7881ec96ef1 100644
--- a/arch/powerpc/kernel/prom_init.c
+++ b/arch/powerpc/kernel/prom_init.c
@@ -605,7 +605,8 @@ static void __init early_cmdline_parse(void)
 	opt = strstr(RELOC(prom_cmd_line), RELOC("crashkernel="));
 	if (opt) {
 		opt += 12;
-		RELOC(prom_crashk_size) = prom_memparse(opt, &opt);
+		RELOC(prom_crashk_size) = 
+			prom_memparse(opt, (const char **)&opt);
 
 		if (ALIGN(RELOC(prom_crashk_size), 0x1000000) !=
 			RELOC(prom_crashk_size)) {
diff --git a/arch/powerpc/platforms/maple/pci.c b/arch/powerpc/platforms/maple/pci.c
index f40451da037..7d4099a34f9 100644
--- a/arch/powerpc/platforms/maple/pci.c
+++ b/arch/powerpc/platforms/maple/pci.c
@@ -316,7 +316,6 @@ static int __init add_bridge(struct device_node *dev)
 	char* disp_name;
 	int *bus_range;
 	int primary = 1;
-	struct property *of_prop;
 
 	DBG("Adding PCI host bridge %s\n", dev->full_name);
 
diff --git a/arch/powerpc/platforms/maple/setup.c b/arch/powerpc/platforms/maple/setup.c
index a1cb4d23672..ec5c1e10c40 100644
--- a/arch/powerpc/platforms/maple/setup.c
+++ b/arch/powerpc/platforms/maple/setup.c
@@ -71,38 +71,60 @@
 #define DBG(fmt...)
 #endif
 
+static unsigned long maple_find_nvram_base(void)
+{
+	struct device_node *rtcs;
+	unsigned long result = 0;
+
+	/* find NVRAM device */
+	rtcs = of_find_compatible_node(NULL, "nvram", "AMD8111");
+	if (rtcs) {
+		struct resource r;
+		if (of_address_to_resource(rtcs, 0, &r)) {
+			printk(KERN_EMERG "Maple: Unable to translate NVRAM"
+			       " address\n");
+			goto bail;
+		}
+		if (!(r.flags & IORESOURCE_IO)) {
+			printk(KERN_EMERG "Maple: NVRAM address isn't PIO!\n");
+			goto bail;
+		}
+		result = r.start;
+	} else
+		printk(KERN_EMERG "Maple: Unable to find NVRAM\n");
+ bail:
+	of_node_put(rtcs);
+	return result;
+}
+
 static void maple_restart(char *cmd)
 {
 	unsigned int maple_nvram_base;
 	unsigned int maple_nvram_offset;
 	unsigned int maple_nvram_command;
-	struct device_node *rtcs;
+	struct device_node *sp;
 
-	/* find NVRAM device */
-	rtcs = find_compatible_devices("nvram", "AMD8111");
-	if (rtcs && rtcs->addrs) {
-		maple_nvram_base = rtcs->addrs[0].address;
-	} else {
-		printk(KERN_EMERG "Maple: Unable to find NVRAM\n");
-		printk(KERN_EMERG "Maple: Manual Restart Required\n");
-		return;
-	}
+	maple_nvram_base = maple_find_nvram_base();
+	if (maple_nvram_base == 0)
+		goto fail;
 
 	/* find service processor device */
-	rtcs = find_devices("service-processor");
-	if (!rtcs) {
+	sp = of_find_node_by_name(NULL, "service-processor");
+	if (!sp) {
 		printk(KERN_EMERG "Maple: Unable to find Service Processor\n");
-		printk(KERN_EMERG "Maple: Manual Restart Required\n");
-		return;
+		goto fail;
 	}
-	maple_nvram_offset = *(unsigned int*) get_property(rtcs,
+	maple_nvram_offset = *(unsigned int*) get_property(sp,
 			"restart-addr", NULL);
-	maple_nvram_command = *(unsigned int*) get_property(rtcs,
+	maple_nvram_command = *(unsigned int*) get_property(sp,
 			"restart-value", NULL);
+	of_node_put(sp);
 
 	/* send command */
 	outb_p(maple_nvram_command, maple_nvram_base + maple_nvram_offset);
 	for (;;) ;
+ fail:
+	printk(KERN_EMERG "Maple: Manual Restart Required\n");
 }
 
 static void maple_power_off(void)
@@ -110,33 +132,29 @@ static void maple_power_off(void)
 	unsigned int maple_nvram_base;
 	unsigned int maple_nvram_offset;
 	unsigned int maple_nvram_command;
-	struct device_node *rtcs;
+	struct device_node *sp;
 
-	/* find NVRAM device */
-	rtcs = find_compatible_devices("nvram", "AMD8111");
-	if (rtcs && rtcs->addrs) {
-		maple_nvram_base = rtcs->addrs[0].address;
-	} else {
-		printk(KERN_EMERG "Maple: Unable to find NVRAM\n");
-		printk(KERN_EMERG "Maple: Manual Power-Down Required\n");
-		return;
-	}
+	maple_nvram_base = maple_find_nvram_base();
+	if (maple_nvram_base == 0)
+		goto fail;
 
 	/* find service processor device */
-	rtcs = find_devices("service-processor");
-	if (!rtcs) {
+	sp = of_find_node_by_name(NULL, "service-processor");
+	if (!sp) {
 		printk(KERN_EMERG "Maple: Unable to find Service Processor\n");
-		printk(KERN_EMERG "Maple: Manual Power-Down Required\n");
-		return;
+		goto fail;
 	}
-	maple_nvram_offset = *(unsigned int*) get_property(rtcs,
+	maple_nvram_offset = *(unsigned int*) get_property(sp,
 			"power-off-addr", NULL);
-	maple_nvram_command = *(unsigned int*) get_property(rtcs,
+	maple_nvram_command = *(unsigned int*) get_property(sp,
 			"power-off-value", NULL);
+	of_node_put(sp);
 
 	/* send command */
 	outb_p(maple_nvram_command, maple_nvram_base + maple_nvram_offset);
 	for (;;) ;
+ fail:
+	printk(KERN_EMERG "Maple: Manual Power-Down Required\n");
 }
 
 static void maple_halt(void)
@@ -179,9 +197,6 @@ void __init maple_setup_arch(void)
  */
 static void __init maple_init_early(void)
 {
-	unsigned int default_speed;
-	u64 physport;
-
 	DBG(" -> maple_init_early\n");
 
 	/* Initialize hash table, from now on, we can take hash faults
diff --git a/arch/powerpc/platforms/maple/time.c b/arch/powerpc/platforms/maple/time.c
index 15846cc938a..50bc4eb8535 100644
--- a/arch/powerpc/platforms/maple/time.c
+++ b/arch/powerpc/platforms/maple/time.c
@@ -168,11 +168,24 @@ unsigned long __init maple_get_boot_time(void)
 	struct rtc_time tm;
 	struct device_node *rtcs;
 
-	rtcs = find_compatible_devices("rtc", "pnpPNP,b00");
-	if (rtcs && rtcs->addrs) {
-		maple_rtc_addr = rtcs->addrs[0].address;
-		printk(KERN_INFO "Maple: Found RTC at 0x%x\n", maple_rtc_addr);
-	} else {
+	rtcs = of_find_compatible_node(NULL, "rtc", "pnpPNP,b00");
+	if (rtcs) {
+		struct resource r;
+		if (of_address_to_resource(rtcs, 0, &r)) {
+			printk(KERN_EMERG "Maple: Unable to translate RTC"
+			       " address\n");
+			goto bail;
+		}
+		if (!(r.flags & IORESOURCE_IO)) {
+			printk(KERN_EMERG "Maple: RTC address isn't PIO!\n");
+			goto bail;
+		}
+		maple_rtc_addr = r.start;
+		printk(KERN_INFO "Maple: Found RTC at IO 0x%x\n",
+		       maple_rtc_addr);
+	}
+ bail:
+	if (maple_rtc_addr == 0) {
 		maple_rtc_addr = RTC_PORT(0); /* legacy address */
 		printk(KERN_INFO "Maple: No device node for RTC, assuming "
 		       "legacy address (0x%x)\n", maple_rtc_addr);
diff --git a/arch/ppc/Kconfig b/arch/ppc/Kconfig
index d65810108bc..11899f06bf0 100644
--- a/arch/ppc/Kconfig
+++ b/arch/ppc/Kconfig
@@ -58,11 +58,11 @@ config 6xx
 	help
 	  There are four types of PowerPC chips supported.  The more common
 	  types (601, 603, 604, 740, 750, 7400), the Motorola embedded
-	  versions (821, 823, 850, 855, 860, 52xx, 82xx, 83xx), the IBM embedded
-	  versions (403 and 405) and the high end 64 bit Power processors
-	  (POWER 3, POWER4, and IBM 970 also known as G5)
+	  versions (821, 823, 850, 855, 860, 52xx, 82xx, 83xx), the IBM
+	  embedded versions (403 and 405) and the POWER3 processor.
+	  (For support for more recent 64-bit processors, set ARCH=powerpc.)
 	  Unless you are building a kernel for one of the embedded processor
-	  systems, 64 bit IBM RS/6000 or an Apple G5, choose 6xx.
+	  systems or a POWER3-based IBM RS/6000, choose 6xx.
 	  Note that the kernel runs in 32-bit mode even on 64-bit chips.
 	  Also note that because the 52xx, 82xx, & 83xx family has a 603e core,
 	  specific support for that chipset is asked later on.
@@ -77,10 +77,6 @@ config POWER3
 	select PPC_FPU
 	bool "POWER3"
 
-config POWER4
-	select PPC_FPU
-	bool "POWER4 and 970 (G5)"
-
 config 8xx
 	bool "8xx"
 
@@ -123,7 +119,7 @@ config PHYS_64BIT
 
 config ALTIVEC
 	bool "AltiVec Support"
-	depends on 6xx || POWER4
+	depends on 6xx
 	depends on !8260 && !83xx
 	---help---
 	  This option enables kernel support for the Altivec extensions to the
@@ -235,18 +231,9 @@ config KEXEC
 
 source "drivers/cpufreq/Kconfig"
 
-config CPU_FREQ_PMAC
-	bool "Support for Apple PowerBooks"
-	depends on CPU_FREQ && ADB_PMU
-	select CPU_FREQ_TABLE
-	help
-	  This adds support for frequency switching on Apple PowerBooks,
-	  this currently includes some models of iBook & Titanium
-	  PowerBook.
-
 config PPC601_SYNC_FIX
 	bool "Workarounds for PPC601 bugs"
-	depends on 6xx && (PPC_PREP || PPC_PMAC)
+	depends on 6xx && PPC_PREP
 	help
 	  Some versions of the PPC601 (the first PowerPC chip) have bugs which
 	  mean that extra synchronization instructions are required near
@@ -258,26 +245,17 @@ config PPC601_SYNC_FIX
 
 	  If in doubt, say Y here.
 
-config HOTPLUG_CPU
-	bool "Support for enabling/disabling CPUs"
-	depends on SMP && HOTPLUG && EXPERIMENTAL && PPC_PMAC
-	---help---
-	  Say Y here to be able to disable and re-enable individual
-	  CPUs at runtime on SMP machines.
-
-	  Say N if you are unsure.
-
 source arch/ppc/platforms/4xx/Kconfig
 source arch/ppc/platforms/85xx/Kconfig
 
 config PPC64BRIDGE
 	bool
-	depends on POWER3 || POWER4
+	depends on POWER3
 	default y
 
 config PPC_STD_MMU
 	bool
-	depends on 6xx || POWER3 || POWER4
+	depends on 6xx || POWER3
 	default y
 
 config NOT_COHERENT_CACHE
@@ -505,7 +483,7 @@ endchoice
 
 choice
 	prompt "Machine Type"
-	depends on 6xx || POWER3 || POWER4
+	depends on 6xx || POWER3
 	default PPC_MULTIPLATFORM
 	---help---
 	  Linux currently supports several different kinds of PowerPC-based
@@ -516,11 +494,15 @@ choice
 	  Platform) machines (including all of the recent IBM RS/6000 and
 	  pSeries machines), and several embedded PowerPC systems containing
 	  4xx, 6xx, 7xx, 8xx, 74xx, and 82xx processors.  Currently, the
-	  default option is to build a kernel which works on the first three.
+	  default option is to build a kernel which works on PReP and CHRP.
 
-	  Select CHRP/PowerMac/PReP if configuring for an IBM RS/6000 or
-	  pSeries machine, a Power Macintosh (including iMacs, iBooks and
-	  Powerbooks), or a PReP machine.
+	  Note that support for Apple machines is now only available with
+	  ARCH=powerpc, and has been removed from this menu.  If you wish
+	  to build a kernel for an Apple machine, exit this configuration
+	  process and re-run it with ARCH=powerpc.
+
+	  Select CHRP/PReP if configuring for an IBM RS/6000 or
+	  pSeries machine, or a PReP machine.
 
 	  Select Gemini if configuring for a Synergy Microsystems' Gemini
 	  series Single Board Computer.  More information is available at:
@@ -530,7 +512,7 @@ choice
 	  available at: <http://linux-apus.sourceforge.net/>.
 
 config PPC_MULTIPLATFORM
-	bool "CHRP/PowerMac/PReP"
+	bool "CHRP/PReP"
 
 config APUS
 	bool "Amiga-APUS"
@@ -768,25 +750,14 @@ config CPM2
 	  on it (826x, 827x, 8560).
 
 config PPC_CHRP
-	bool
+	bool "Support for CHRP (Common Hardware Reference Platform) machines"
 	depends on PPC_MULTIPLATFORM
 	select PPC_I8259
 	select PPC_INDIRECT_PCI
 	default y
 
-config PPC_PMAC
-	bool
-	depends on PPC_MULTIPLATFORM
-	select PPC_INDIRECT_PCI
-	default y
-
-config PPC_PMAC64
-	bool
-	depends on PPC_PMAC && POWER4
-	default y
-
 config PPC_PREP
-	bool
+	bool "Support for PReP (PowerPC Reference Platform) machines"
 	depends on PPC_MULTIPLATFORM
 	select PPC_I8259
 	select PPC_INDIRECT_PCI
@@ -794,7 +765,7 @@ config PPC_PREP
 
 config PPC_OF
 	bool
-	depends on PPC_PMAC || PPC_CHRP
+	depends on PPC_CHRP
 	default y
 
 config PPC_GEN550
@@ -1166,7 +1137,7 @@ config ISA
 
 config GENERIC_ISA_DMA
 	bool
-	depends on POWER3 || POWER4 || 6xx && !CPM2
+	depends on POWER3 || 6xx && !CPM2
 	default y
 
 config PPC_I8259
diff --git a/arch/ppc/boot/Makefile b/arch/ppc/boot/Makefile
index 995f89bb049..efd8ce515d5 100644
--- a/arch/ppc/boot/Makefile
+++ b/arch/ppc/boot/Makefile
@@ -18,7 +18,7 @@ BOOT_TARGETS	= zImage zImage.initrd znetboot znetboot.initrd
 bootdir-y			:= simple
 bootdir-$(CONFIG_PPC_OF)	+= openfirmware
 subdir-y			:= lib common images
-subdir-$(CONFIG_PPC_OF)		+= of1275
+subdir-$(CONFIG_PPC_MULTIPLATFORM)	+= of1275
 
 # for cleaning
 subdir-				+= simple openfirmware
diff --git a/arch/ppc/boot/openfirmware/Makefile b/arch/ppc/boot/openfirmware/Makefile
index 83a6433459c..2a411ec2e65 100644
--- a/arch/ppc/boot/openfirmware/Makefile
+++ b/arch/ppc/boot/openfirmware/Makefile
@@ -21,26 +21,16 @@ bootlib	:= $(boot)/lib
 of1275	:= $(boot)/of1275
 images	:= $(boot)/images
 
-OBJCOPY_ARGS	:= -O aixcoff-rs6000 -R .stab -R .stabstr -R .comment
-COFF_LD_ARGS	:= -T $(srctree)/$(boot)/ld.script -e _start -Ttext 0x00500000 \
-			-Bstatic
 CHRP_LD_ARGS	:= -T $(srctree)/$(boot)/ld.script -e _start -Ttext 0x00800000
-NEWWORLD_LD_ARGS:= -T $(srctree)/$(boot)/ld.script -e _start -Ttext 0x01000000
 
 COMMONOBJS	:= start.o misc.o common.o
-COFFOBJS	:= coffcrt0.o $(COMMONOBJS) coffmain.o
 CHRPOBJS	:= crt0.o     $(COMMONOBJS) chrpmain.o
-NEWWORLDOBJS	:= crt0.o     $(COMMONOBJS) newworldmain.o
 
-targets 	:= $(COFFOBJS) $(CHRPOBJS) $(NEWWORLDOBJS) dummy.o
-COFFOBJS	:= $(addprefix $(obj)/, $(COFFOBJS))
+targets 	:= $(CHRPOBJS) dummy.o
 CHRPOBJS	:= $(addprefix $(obj)/, $(CHRPOBJS))
-NEWWORLDOBJS	:= $(addprefix $(obj)/, $(NEWWORLDOBJS))
 
 LIBS		:= lib/lib.a $(bootlib)/lib.a $(of1275)/lib.a $(common)/lib.a
 
-HACKCOFF := $(utils)/hack-coff
-
 ifdef CONFIG_SMP
 END := .smp
 endif
@@ -72,56 +62,11 @@ targets += image.initrd.o
 $(obj)/image.initrd.o: $(obj)/image.o $(images)/ramdisk.image.gz FORCE
 	$(call if_changed,genimage-initrd)
 
-# Create the note section for New-World PowerMacs.
-quiet_cmd_mknote = MKNOTE  $@
-     cmd_mknote  = $(utils)/mknote > $@
-targets		+= note
-$(obj)/note: $(utils)/mknote FORCE
-	$(call if_changed,mknote)
-
 
-$(obj)/coffcrt0.o: EXTRA_AFLAGS := -DXCOFF
-targets += coffcrt0.o crt0.o
-$(obj)/coffcrt0.o $(obj)/crt0.o: $(common)/crt0.S FORCE
+targets += crt0.o
+$(obj)/crt0.o: $(common)/crt0.S FORCE
 	$(call if_changed_dep,as_o_S)
 
-quiet_cmd_gencoffb = COFF    $@
-      cmd_gencoffb = $(LD) -o $@ $(COFF_LD_ARGS) $(COFFOBJS) $< $(LIBS) && \
-                     $(OBJCOPY) $@ $@ -R .comment $(del-ramdisk-sec)
-targets += coffboot
-$(obj)/coffboot: $(obj)/image.o $(COFFOBJS) $(LIBS) $(srctree)/$(boot)/ld.script FORCE
-	$(call if_changed,gencoffb)
-targets += coffboot.initrd
-$(obj)/coffboot.initrd: $(obj)/image.initrd.o $(COFFOBJS) $(LIBS) \
-			$(srctree)/$(boot)/ld.script FORCE
-	$(call if_changed,gencoffb)
-
-
-quiet_cmd_gen-coff = COFF    $@
-      cmd_gen-coff = $(OBJCOPY) $(OBJCOPY_ARGS) $< $@ && \
-			$(HACKCOFF) $@ && \
-			ln -sf $(notdir $@) $(images)/zImage$(initrd).pmac
-
-$(images)/vmlinux.coff: $(obj)/coffboot
-	$(call cmd,gen-coff)
-
-$(images)/vmlinux.initrd.coff: $(obj)/coffboot.initrd
-	$(call cmd,gen-coff)
-
-quiet_cmd_gen-elf-pmac = ELF     $@
-      cmd_gen-elf-pmac = $(LD) $(NEWWORLD_LD_ARGS) -o $@ \
-				$(NEWWORLDOBJS) $(LIBS) $< && \
-			$(OBJCOPY) $@ $@ --add-section=.note=$(obj)/note \
-					 -R .comment $(del-ramdisk-sec)
-
-$(images)/vmlinux.elf-pmac: $(obj)/image.o $(NEWWORLDOBJS) $(LIBS) \
-			$(obj)/note $(srctree)/$(boot)/ld.script
-	$(call cmd,gen-elf-pmac)
-$(images)/vmlinux.initrd.elf-pmac: $(obj)/image.initrd.o $(NEWWORLDOBJS) \
-				   $(LIBS) $(obj)/note \
-				   $(srctree)/$(boot)/ld.script
-	$(call cmd,gen-elf-pmac)
-
 quiet_cmd_gen-chrp = CHRP    $@
       cmd_gen-chrp = $(LD) $(CHRP_LD_ARGS) -o $@ $(CHRPOBJS) $< $(LIBS) && \
 			$(OBJCOPY) $@ $@ -R .comment $(del-ramdisk-sec)
@@ -139,46 +84,23 @@ $(images)/zImage.chrp-rs6k $(images)/zImage.initrd.chrp-rs6k: \
 	%-rs6k: %
 	$(call cmd,addnote)
 
-quiet_cmd_gen-miboot = GEN     $@
-      cmd_gen-miboot = $(OBJCOPY) $(OBJCOPY_ARGS) \
-		       --add-section=$1=$(word 2, $^) $< $@
-$(images)/miboot.image: $(obj)/dummy.o $(images)/vmlinux.gz
-	$(call cmd,gen-miboot,image)
-
-$(images)/miboot.initrd.image: $(images)/miboot.image $(images)/ramdisk.image.gz
-	$(call cmd,gen-miboot,initrd)
-
 # The targets used on the make command-line
 
 .PHONY: zImage zImage.initrd
-zImage:		 $(images)/vmlinux.coff 	\
-		 $(images)/vmlinux.elf-pmac	\
-		 $(images)/zImage.chrp		\
-		 $(images)/zImage.chrp-rs6k	\
-		 $(images)/miboot.image
+zImage:		 $(images)/zImage.chrp		\
+		 $(images)/zImage.chrp-rs6k
 	@echo '  kernel: $@ is ready ($<)'
-zImage.initrd:	 $(images)/vmlinux.initrd.coff 		\
-		 $(images)/vmlinux.initrd.elf-pmac	\
-		 $(images)/zImage.initrd.chrp		\
-		 $(images)/zImage.initrd.chrp-rs6k	\
-		 $(images)/miboot.initrd.image
+zImage.initrd:	 $(images)/zImage.initrd.chrp		\
+		 $(images)/zImage.initrd.chrp-rs6k
 	@echo '  kernel: $@ is ready ($<)'
 
 TFTPIMAGE	:= /tftpboot/zImage
 
 .PHONY: znetboot znetboot.initrd
-znetboot:	$(images)/vmlinux.coff		\
-		$(images)/vmlinux.elf-pmac	\
-		$(images)/zImage.chrp
-	cp $(images)/vmlinux.coff     $(TFTPIMAGE).pmac$(END)
-	cp $(images)/vmlinux.elf-pmac $(TFTPIMAGE).pmac$(END).elf
+znetboot:	$(images)/zImage.chrp
 	cp $(images)/zImage.chrp      $(TFTPIMAGE).chrp$(END)
 	@echo '  kernel: $@ is ready ($<)'
-znetboot.initrd:$(images)/vmlinux.initrd.coff		\
-		$(images)/vmlinux.initrd.elf-pmac	\
-		$(images)/zImage.initrd.chrp
-	cp $(images)/vmlinux.initrd.coff     $(TFTPIMAGE).pmac$(END)
-	cp $(images)/vmlinux.initrd.elf-pmac $(TFTPIMAGE).pmac$(END).elf
+znetboot.initrd:$(images)/zImage.initrd.chrp
 	cp $(images)/zImage.initrd.chrp      $(TFTPIMAGE).chrp$(END)
 	@echo '  kernel: $@ is ready ($<)'
 
diff --git a/arch/ppc/boot/openfirmware/coffmain.c b/arch/ppc/boot/openfirmware/coffmain.c
deleted file mode 100644
index 2da8855e2be..00000000000
--- a/arch/ppc/boot/openfirmware/coffmain.c
+++ /dev/null
@@ -1,101 +0,0 @@
-/*
- * Copyright (C) Paul Mackerras 1997.
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License
- * as published by the Free Software Foundation; either version
- * 2 of the License, or (at your option) any later version.
- */
-#include <linux/string.h>
-#include <asm/processor.h>
-#include <asm/page.h>
-
-#include "nonstdio.h"
-#include "of1275.h"
-
-/* Passed from the linker */
-extern char __image_begin, __image_end;
-extern char __ramdisk_begin[], __ramdisk_end;
-extern char _start, _end;
-
-extern char image_data[], initrd_data[];
-extern int initrd_len, image_len;
-extern unsigned int heap_max;
-extern void flush_cache(void *start, unsigned int len);
-extern void gunzip(void *, int, unsigned char *, int *);
-extern void make_bi_recs(unsigned long addr, char *name, unsigned int mach,
-		unsigned int progend);
-extern void setup_bats(unsigned long start);
-
-char *avail_ram;
-char *begin_avail, *end_avail;
-char *avail_high;
-
-#define SCRATCH_SIZE	(128 << 10)
-
-static char heap[SCRATCH_SIZE];
-
-static unsigned long ram_start = 0;
-static unsigned long ram_end = 0x1000000;
-
-static unsigned long prog_start = 0x800000;
-static unsigned long prog_size = 0x700000;
-
-typedef void (*kernel_start_t)(int, int, void *);
-
-void boot(int a1, int a2, void *prom)
-{
-    unsigned sa, len;
-    void *dst;
-    unsigned char *im;
-    unsigned initrd_start, initrd_size;
-
-    printf("coffboot starting: loaded at 0x%p\n", &_start);
-    setup_bats(ram_start);
-
-    initrd_size = (char *)(&__ramdisk_end) - (char *)(&__ramdisk_begin);
-    if (initrd_size) {
-	initrd_start = (ram_end - initrd_size) & ~0xFFF;
-	a1 = initrd_start;
-	a2 = initrd_size;
-	claim(initrd_start, ram_end - initrd_start, 0);
-	printf("initial ramdisk moving 0x%x <- 0x%p (%x bytes)\n\r",
-	       initrd_start, (char *)(&__ramdisk_begin), initrd_size);
-	memcpy((char *)initrd_start, (char *)(&__ramdisk_begin), initrd_size);
-	prog_size = initrd_start - prog_start;
-    } else
-	a2 = 0xdeadbeef;
-
-    im = (char *)(&__image_begin);
-    len = (char *)(&__image_end) - (char *)(&__image_begin);
-    /* claim 4MB starting at PROG_START */
-    claim(prog_start, prog_size, 0);
-    map(prog_start, prog_start, prog_size);
-    dst = (void *) prog_start;
-    if (im[0] == 0x1f && im[1] == 0x8b) {
-	/* set up scratch space */
-	begin_avail = avail_high = avail_ram = heap;
-	end_avail = heap + sizeof(heap);
-	printf("heap at 0x%p\n", avail_ram);
-	printf("gunzipping (0x%p <- 0x%p:0x%p)...", dst, im, im+len);
-	gunzip(dst, prog_size, im, &len);
-	printf("done %u bytes\n", len);
-	printf("%u bytes of heap consumed, max in use %u\n",
-	       avail_high - begin_avail, heap_max);
-    } else {
-	memmove(dst, im, len);
-    }
-
-    flush_cache(dst, len);
-    make_bi_recs(((unsigned long) dst + len), "coffboot", _MACH_Pmac,
-		    (prog_start + prog_size));
-
-    sa = (unsigned long)prog_start;
-    printf("start address = 0x%x\n", sa);
-
-    (*(kernel_start_t)sa)(a1, a2, prom);
-
-    printf("returned?\n");
-
-    pause();
-}
diff --git a/arch/ppc/boot/openfirmware/newworldmain.c b/arch/ppc/boot/openfirmware/newworldmain.c
deleted file mode 100644
index fa8a8f9313f..00000000000
--- a/arch/ppc/boot/openfirmware/newworldmain.c
+++ /dev/null
@@ -1,94 +0,0 @@
-/*
- * Copyright (C) Paul Mackerras 1997.
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License
- * as published by the Free Software Foundation; either version
- * 2 of the License, or (at your option) any later version.
- */
-#include <linux/string.h>
-#include "nonstdio.h"
-#include "of1275.h"
-#include <asm/processor.h>
-#include <asm/page.h>
-
-/* Passed from the linker */
-extern char __image_begin, __image_end;
-extern char __ramdisk_begin[], __ramdisk_end;
-extern char _start, _end;
-
-extern unsigned int heap_max;
-extern void flush_cache(void *start, unsigned int len);
-extern void gunzip(void *, int, unsigned char *, int *);
-extern void make_bi_recs(unsigned long addr, char *name, unsigned int mach,
-		unsigned int progend);
-
-char *avail_ram;
-char *begin_avail, *end_avail;
-char *avail_high;
-
-
-#define RAM_END		(16 << 20)
-
-#define PROG_START	0x00010000
-#define PROG_SIZE	0x007f0000
-
-#define SCRATCH_SIZE	(128 << 10)
-
-typedef void (*kernel_start_t)(int, int, void *);
-
-void boot(int a1, int a2, void *prom)
-{
-    unsigned sa, len;
-    void *dst;
-    unsigned char *im;
-    unsigned initrd_start, initrd_size;
-
-    printf("chrpboot starting: loaded at 0x%p\n", &_start);
-
-    initrd_size = (char *)(&__ramdisk_end) - (char *)(&__ramdisk_begin);
-    if (initrd_size) {
-	initrd_start = (RAM_END - initrd_size) & ~0xFFF;
-	a1 = initrd_start;
-	a2 = initrd_size;
-	claim(initrd_start, RAM_END - initrd_start, 0);
-	printf("initial ramdisk moving 0x%x <- 0x%p (%x bytes)\n\r",
-	       initrd_start, (char *)(&__ramdisk_begin), initrd_size);
-	memcpy((char *)initrd_start, (char *)(&__ramdisk_begin), initrd_size);
-    } else
-	a2 = 0xdeadbeef;
-
-    im = (char *)(&__image_begin);
-    len = (char *)(&__image_end) - (char *)(&__image_begin);
-    /* claim 3MB starting at PROG_START */
-    claim(PROG_START, PROG_SIZE, 0);
-    dst = (void *) PROG_START;
-    if (im[0] == 0x1f && im[1] == 0x8b) {
-	/* claim some memory for scratch space */
-	avail_ram = (char *) claim(0, SCRATCH_SIZE, 0x10);
-	begin_avail = avail_high = avail_ram;
-	end_avail = avail_ram + SCRATCH_SIZE;
-	printf("heap at 0x%p\n", avail_ram);
-	printf("gunzipping (0x%p <- 0x%p:0x%p)...", dst, im, im+len);
-	gunzip(dst, PROG_SIZE, im, &len);
-	printf("done %u bytes\n", len);
-	printf("%u bytes of heap consumed, max in use %u\n",
-	       avail_high - begin_avail, heap_max);
-	release(begin_avail, SCRATCH_SIZE);
-    } else {
-	memmove(dst, im, len);
-    }
-
-    flush_cache(dst, len);
-    make_bi_recs(((unsigned long) dst + len), "chrpboot", _MACH_Pmac,
-		    (PROG_START + PROG_SIZE));
-
-    sa = (unsigned long)PROG_START;
-    printf("start address = 0x%x\n", sa);
-
-    (*(kernel_start_t)sa)(a1, a2, prom);
-
-    printf("returned?\n");
-
-    pause();
-}
diff --git a/arch/ppc/kernel/Makefile b/arch/ppc/kernel/Makefile
index ca020130086..e399bbb969a 100644
--- a/arch/ppc/kernel/Makefile
+++ b/arch/ppc/kernel/Makefile
@@ -9,7 +9,6 @@ extra-$(CONFIG_44x)		:= head_44x.o
 extra-$(CONFIG_FSL_BOOKE)	:= head_fsl_booke.o
 extra-$(CONFIG_8xx)		:= head_8xx.o
 extra-$(CONFIG_6xx)		+= idle_6xx.o
-extra-$(CONFIG_POWER4)		+= idle_power4.o
 extra-y				+= vmlinux.lds
 
 obj-y				:= entry.o traps.o idle.o time.o misc.o \
@@ -17,7 +16,6 @@ obj-y				:= entry.o traps.o idle.o time.o misc.o \
 					ppc_htab.o
 obj-$(CONFIG_6xx)		+= l2cr.o cpu_setup_6xx.o
 obj-$(CONFIG_SOFTWARE_SUSPEND)	+= swsusp.o
-obj-$(CONFIG_POWER4)		+= cpu_setup_power4.o
 obj-$(CONFIG_MODULES)		+= module.o ppc_ksyms.o
 obj-$(CONFIG_NOT_COHERENT_CACHE)	+= dma-mapping.o
 obj-$(CONFIG_PCI)		+= pci.o
@@ -42,7 +40,6 @@ obj-$(CONFIG_6xx)		+= l2cr.o cpu_setup_6xx.o
 obj-$(CONFIG_SOFTWARE_SUSPEND)	+= swsusp.o
 obj-$(CONFIG_MODULES)		+= module.o
 obj-$(CONFIG_NOT_COHERENT_CACHE)	+= dma-mapping.o
-obj-$(CONFIG_PCI)		+= pci.o
 obj-$(CONFIG_KGDB)		+= ppc-stub.o
 obj-$(CONFIG_TAU)		+= temp.o
 ifndef CONFIG_E200
diff --git a/arch/ppc/kernel/misc.S b/arch/ppc/kernel/misc.S
index fb5658bba28..c3427eed834 100644
--- a/arch/ppc/kernel/misc.S
+++ b/arch/ppc/kernel/misc.S
@@ -204,78 +204,6 @@ _GLOBAL(call_setup_cpu)
 	mtctr	r5
 	bctr
 
-#if defined(CONFIG_CPU_FREQ_PMAC) && defined(CONFIG_6xx)
-
-/* This gets called by via-pmu.c to switch the PLL selection
- * on 750fx CPU. This function should really be moved to some
- * other place (as most of the cpufreq code in via-pmu
- */
-_GLOBAL(low_choose_750fx_pll)
-	/* Clear MSR:EE */
-	mfmsr	r7
-	rlwinm	r0,r7,0,17,15
-	mtmsr	r0
-
-	/* If switching to PLL1, disable HID0:BTIC */
-	cmplwi	cr0,r3,0
-	beq	1f
-	mfspr	r5,SPRN_HID0
-	rlwinm	r5,r5,0,27,25
-	sync
-	mtspr	SPRN_HID0,r5
-	isync
-	sync
-
-1:
-	/* Calc new HID1 value */
-	mfspr	r4,SPRN_HID1	/* Build a HID1:PS bit from parameter */
-	rlwinm	r5,r3,16,15,15	/* Clear out HID1:PS from value read */
-	rlwinm	r4,r4,0,16,14	/* Could have I used rlwimi here ? */
-	or	r4,r4,r5
-	mtspr	SPRN_HID1,r4
-
-	/* Store new HID1 image */
-	rlwinm	r6,r1,0,0,18
-	lwz	r6,TI_CPU(r6)
-	slwi	r6,r6,2
-	addis	r6,r6,nap_save_hid1@ha
-	stw	r4,nap_save_hid1@l(r6)
-
-	/* If switching to PLL0, enable HID0:BTIC */
-	cmplwi	cr0,r3,0
-	bne	1f
-	mfspr	r5,SPRN_HID0
-	ori	r5,r5,HID0_BTIC
-	sync
-	mtspr	SPRN_HID0,r5
-	isync
-	sync
-
-1:
-	/* Return */
-	mtmsr	r7
-	blr
-
-_GLOBAL(low_choose_7447a_dfs)
-	/* Clear MSR:EE */
-	mfmsr	r7
-	rlwinm	r0,r7,0,17,15
-	mtmsr	r0
-	
-	/* Calc new HID1 value */
-	mfspr	r4,SPRN_HID1
-	insrwi	r4,r3,1,9	/* insert parameter into bit 9 */
-	sync
-	mtspr	SPRN_HID1,r4
-	sync
-	isync
-
-	/* Return */
-	mtmsr	r7
-	blr
-
-#endif /* CONFIG_CPU_FREQ_PMAC && CONFIG_6xx */
-
 /*
  * complement mask on the msr then "or" some values on.
  *     _nmask_and_or_msr(nmask, value_to_or)
diff --git a/arch/ppc/kernel/pci.c b/arch/ppc/kernel/pci.c
index 704c846b2b0..04d04c5bfdd 100644
--- a/arch/ppc/kernel/pci.c
+++ b/arch/ppc/kernel/pci.c
@@ -1,5 +1,5 @@
 /*
- * Common pmac/prep/chrp pci routines. -- Cort
+ * Common prep/chrp pci routines. -- Cort
  */
 
 #include <linux/config.h>
@@ -50,8 +50,7 @@ static void fixup_cpc710_pci64(struct pci_dev* dev);
 static u8* pci_to_OF_bus_map;
 #endif
 
-/* By default, we don't re-assign bus numbers. We do this only on
- * some pmacs
+/* By default, we don't re-assign bus numbers.
  */
 int pci_assign_all_buses;
 
@@ -780,17 +779,6 @@ pci_busdev_to_OF_node(struct pci_bus *bus, int devfn)
 		return NULL;
 
 	/* Fixup bus number according to what OF think it is. */
-#ifdef CONFIG_PPC_PMAC
-	/* The G5 need a special case here. Basically, we don't remap all
-	 * busses on it so we don't create the pci-OF-map. However, we do
-	 * remap the AGP bus and so have to deal with it. A future better
-	 * fix has to be done by making the remapping per-host and always
-	 * filling the pci_to_OF map. --BenH
-	 */
-	if (_machine == _MACH_Pmac && busnr >= 0xf0)
-		busnr -= 0xf0;
-	else
-#endif
 	if (pci_to_OF_bus_map)
 		busnr = pci_to_OF_bus_map[busnr];
 	if (busnr == 0xff)
@@ -1040,216 +1028,6 @@ void pcibios_add_platform_entries(struct pci_dev *pdev)
 }
 
 
-#ifdef CONFIG_PPC_PMAC
-/*
- * This set of routines checks for PCI<->PCI bridges that have closed
- * IO resources and have child devices. It tries to re-open an IO
- * window on them.
- *
- * This is a _temporary_ fix to workaround a problem with Apple's OF
- * closing IO windows on P2P bridges when the OF drivers of cards
- * below this bridge don't claim any IO range (typically ATI or
- * Adaptec).
- *
- * A more complete fix would be to use drivers/pci/setup-bus.c, which
- * involves a working pcibios_fixup_pbus_ranges(), some more care about
- * ordering when creating the host bus resources, and maybe a few more
- * minor tweaks
- */
-
-/* Initialize bridges with base/limit values we have collected */
-static void __init
-do_update_p2p_io_resource(struct pci_bus *bus, int enable_vga)
-{
-	struct pci_dev *bridge = bus->self;
-	struct pci_controller* hose = (struct pci_controller *)bridge->sysdata;
-	u32 l;
-	u16 w;
-	struct resource res;
-
-	if (bus->resource[0] == NULL)
-		return;
- 	res = *(bus->resource[0]);
-
-	DBG("Remapping Bus %d, bridge: %s\n", bus->number, pci_name(bridge));
-	res.start -= ((unsigned long) hose->io_base_virt - isa_io_base);
-	res.end -= ((unsigned long) hose->io_base_virt - isa_io_base);
-	DBG("  IO window: %08lx-%08lx\n", res.start, res.end);
-
-	/* Set up the top and bottom of the PCI I/O segment for this bus. */
-	pci_read_config_dword(bridge, PCI_IO_BASE, &l);
-	l &= 0xffff000f;
-	l |= (res.start >> 8) & 0x00f0;
-	l |= res.end & 0xf000;
-	pci_write_config_dword(bridge, PCI_IO_BASE, l);
-
-	if ((l & PCI_IO_RANGE_TYPE_MASK) == PCI_IO_RANGE_TYPE_32) {
-		l = (res.start >> 16) | (res.end & 0xffff0000);
-		pci_write_config_dword(bridge, PCI_IO_BASE_UPPER16, l);
-	}
-
-	pci_read_config_word(bridge, PCI_COMMAND, &w);
-	w |= PCI_COMMAND_IO;
-	pci_write_config_word(bridge, PCI_COMMAND, w);
-
-#if 0 /* Enabling this causes XFree 4.2.0 to hang during PCI probe */
-	if (enable_vga) {
-		pci_read_config_word(bridge, PCI_BRIDGE_CONTROL, &w);
-		w |= PCI_BRIDGE_CTL_VGA;
-		pci_write_config_word(bridge, PCI_BRIDGE_CONTROL, w);
-	}
-#endif
-}
-
-/* This function is pretty basic and actually quite broken for the
- * general case, it's enough for us right now though. It's supposed
- * to tell us if we need to open an IO range at all or not and what
- * size.
- */
-static int __init
-check_for_io_childs(struct pci_bus *bus, struct resource* res, int *found_vga)
-{
-	struct pci_dev *dev;
-	int	i;
-	int	rc = 0;
-
-#define push_end(res, size) do { unsigned long __sz = (size) ; \
-	res->end = ((res->end + __sz) / (__sz + 1)) * (__sz + 1) + __sz; \
-    } while (0)
-
-	list_for_each_entry(dev, &bus->devices, bus_list) {
-		u16 class = dev->class >> 8;
-
-		if (class == PCI_CLASS_DISPLAY_VGA ||
-		    class == PCI_CLASS_NOT_DEFINED_VGA)
-			*found_vga = 1;
-		if (class >> 8 == PCI_BASE_CLASS_BRIDGE && dev->subordinate)
-			rc |= check_for_io_childs(dev->subordinate, res, found_vga);
-		if (class == PCI_CLASS_BRIDGE_CARDBUS)
-			push_end(res, 0xfff);
-
-		for (i=0; i<PCI_NUM_RESOURCES; i++) {
-			struct resource *r;
-			unsigned long r_size;
-
-			if (dev->class >> 8 == PCI_CLASS_BRIDGE_PCI
-			    && i >= PCI_BRIDGE_RESOURCES)
-				continue;
-			r = &dev->resource[i];
-			r_size = r->end - r->start;
-			if (r_size < 0xfff)
-				r_size = 0xfff;
-			if (r->flags & IORESOURCE_IO && (r_size) != 0) {
-				rc = 1;
-				push_end(res, r_size);
-			}
-		}
-	}
-
-	return rc;
-}
-
-/* Here we scan all P2P bridges of a given level that have a closed
- * IO window. Note that the test for the presence of a VGA card should
- * be improved to take into account already configured P2P bridges,
- * currently, we don't see them and might end up configuring 2 bridges
- * with VGA pass through enabled
- */
-static void __init
-do_fixup_p2p_level(struct pci_bus *bus)
-{
-	struct pci_bus *b;
-	int i, parent_io;
-	int has_vga = 0;
-
-	for (parent_io=0; parent_io<4; parent_io++)
-		if (bus->resource[parent_io]
-		    && bus->resource[parent_io]->flags & IORESOURCE_IO)
-			break;
-	if (parent_io >= 4)
-		return;
-
-	list_for_each_entry(b, &bus->children, node) {
-		struct pci_dev *d = b->self;
-		struct pci_controller* hose = (struct pci_controller *)d->sysdata;
-		struct resource *res = b->resource[0];
-		struct resource tmp_res;
-		unsigned long max;
-		int found_vga = 0;
-
-		memset(&tmp_res, 0, sizeof(tmp_res));
-		tmp_res.start = bus->resource[parent_io]->start;
-
-		/* We don't let low addresses go through that closed P2P bridge, well,
-		 * that may not be necessary but I feel safer that way
-		 */
-		if (tmp_res.start == 0)
-			tmp_res.start = 0x1000;
-	
-		if (!list_empty(&b->devices) && res && res->flags == 0 &&
-		    res != bus->resource[parent_io] &&
-		    (d->class >> 8) == PCI_CLASS_BRIDGE_PCI &&
-		    check_for_io_childs(b, &tmp_res, &found_vga)) {
-			u8 io_base_lo;
-
-			printk(KERN_INFO "Fixing up IO bus %s\n", b->name);
-
-			if (found_vga) {
-				if (has_vga) {
-					printk(KERN_WARNING "Skipping VGA, already active"
-					    " on bus segment\n");
-					found_vga = 0;
-				} else
-					has_vga = 1;
-			}
-			pci_read_config_byte(d, PCI_IO_BASE, &io_base_lo);
-
-			if ((io_base_lo & PCI_IO_RANGE_TYPE_MASK) == PCI_IO_RANGE_TYPE_32)
-				max = ((unsigned long) hose->io_base_virt
-					- isa_io_base) + 0xffffffff;
-			else
-				max = ((unsigned long) hose->io_base_virt
-					- isa_io_base) + 0xffff;
-
-			*res = tmp_res;
-			res->flags = IORESOURCE_IO;
-			res->name = b->name;
-		
-			/* Find a resource in the parent where we can allocate */
-			for (i = 0 ; i < 4; i++) {
-				struct resource *r = bus->resource[i];
-				if (!r)
-					continue;
-				if ((r->flags & IORESOURCE_IO) == 0)
-					continue;
-				DBG("Trying to allocate from %08lx, size %08lx from parent"
-				    " res %d: %08lx -> %08lx\n",
-					res->start, res->end, i, r->start, r->end);
-			
-				if (allocate_resource(r, res, res->end + 1, res->start, max,
-				    res->end + 1, NULL, NULL) < 0) {
-					DBG("Failed !\n");
-					continue;
-				}
-				do_update_p2p_io_resource(b, found_vga);
-				break;
-			}
-		}
-		do_fixup_p2p_level(b);
-	}
-}
-
-static void
-pcibios_fixup_p2p_bridges(void)
-{
-	struct pci_bus *b;
-
-	list_for_each_entry(b, &pci_root_buses, node)
-		do_fixup_p2p_level(b);
-}
-
-#endif /* CONFIG_PPC_PMAC */
-
 static int __init
 pcibios_init(void)
 {
@@ -1290,9 +1068,6 @@ pcibios_init(void)
 	pcibios_allocate_bus_resources(&pci_root_buses);
 	pcibios_allocate_resources(0);
 	pcibios_allocate_resources(1);
-#ifdef CONFIG_PPC_PMAC
-	pcibios_fixup_p2p_bridges();
-#endif /* CONFIG_PPC_PMAC */
 	pcibios_assign_resources();
 
 	/* Call machine dependent post-init code */
@@ -1722,17 +1497,6 @@ long sys_pciconfig_iobase(long which, unsigned long bus, unsigned long devfn)
 	struct pci_controller* hose;
 	long result = -EOPNOTSUPP;
 
-	/* Argh ! Please forgive me for that hack, but that's the
-	 * simplest way to get existing XFree to not lockup on some
-	 * G5 machines... So when something asks for bus 0 io base
-	 * (bus 0 is HT root), we return the AGP one instead.
-	 */
-#ifdef CONFIG_PPC_PMAC
-	if (_machine == _MACH_Pmac && machine_is_compatible("MacRISC4"))
-		if (bus == 0)
-			bus = 0xf0;
-#endif /* CONFIG_PPC_PMAC */
-
 	hose = pci_bus_to_hose(bus);
 	if (!hose)
 		return -ENODEV;
diff --git a/arch/ppc/kernel/ppc_ksyms.c b/arch/ppc/kernel/ppc_ksyms.c
index fb0da7c209d..3a6e4bcb3c5 100644
--- a/arch/ppc/kernel/ppc_ksyms.c
+++ b/arch/ppc/kernel/ppc_ksyms.c
@@ -34,7 +34,6 @@
 #include <asm/system.h>
 #include <asm/pci-bridge.h>
 #include <asm/irq.h>
-#include <asm/pmac_feature.h>
 #include <asm/dma.h>
 #include <asm/machdep.h>
 #include <asm/hw_irq.h>
@@ -58,7 +57,6 @@ extern void machine_check_exception(struct pt_regs *regs);
 extern void alignment_exception(struct pt_regs *regs);
 extern void program_check_exception(struct pt_regs *regs);
 extern void single_step_exception(struct pt_regs *regs);
-extern int pmac_newworld;
 extern int sys_sigreturn(struct pt_regs *regs);
 
 long long __ashrdi3(long long, int);
@@ -213,10 +211,6 @@ EXPORT_SYMBOL(adb_try_handler_change);
 EXPORT_SYMBOL(cuda_request);
 EXPORT_SYMBOL(cuda_poll);
 #endif /* CONFIG_ADB_CUDA */
-#ifdef CONFIG_PPC_PMAC
-EXPORT_SYMBOL(sys_ctrler);
-EXPORT_SYMBOL(pmac_newworld);
-#endif
 #ifdef CONFIG_PPC_OF
 EXPORT_SYMBOL(find_devices);
 EXPORT_SYMBOL(find_type_devices);
@@ -241,9 +235,6 @@ EXPORT_SYMBOL(of_node_put);
 #if defined(CONFIG_BOOTX_TEXT)
 EXPORT_SYMBOL(btext_update_display);
 #endif
-#if defined(CONFIG_SCSI) && defined(CONFIG_PPC_PMAC)
-EXPORT_SYMBOL(note_scsi_host);
-#endif
 #ifdef CONFIG_VT
 EXPORT_SYMBOL(kd_mksound);
 #endif
diff --git a/arch/ppc/kernel/setup.c b/arch/ppc/kernel/setup.c
index e707c6f6e61..c08ab432e95 100644
--- a/arch/ppc/kernel/setup.c
+++ b/arch/ppc/kernel/setup.c
@@ -1,5 +1,5 @@
 /*
- * Common prep/pmac/chrp boot and setup code.
+ * Common prep/chrp boot and setup code.
  */
 
 #include <linux/config.h>
@@ -35,7 +35,6 @@
 #include <asm/machdep.h>
 #include <asm/uaccess.h>
 #include <asm/system.h>
-#include <asm/pmac_feature.h>
 #include <asm/sections.h>
 #include <asm/nvram.h>
 #include <asm/xmon.h>
@@ -55,7 +54,6 @@
 
 extern void platform_init(unsigned long r3, unsigned long r4,
 		unsigned long r5, unsigned long r6, unsigned long r7);
-extern void bootx_init(unsigned long r4, unsigned long phys);
 extern void identify_cpu(unsigned long offset, unsigned long cpu);
 extern void do_cpu_ftr_fixups(unsigned long offset);
 extern void reloc_got2(unsigned long offset);
@@ -80,8 +78,6 @@ EXPORT_SYMBOL(_machine);
 
 extern void prep_init(unsigned long r3, unsigned long r4,
 		unsigned long r5, unsigned long r6, unsigned long r7);
-extern void pmac_init(unsigned long r3, unsigned long r4,
-		unsigned long r5, unsigned long r6, unsigned long r7);
 extern void chrp_init(unsigned long r3, unsigned long r4,
 		unsigned long r5, unsigned long r6, unsigned long r7);
 
@@ -324,20 +320,15 @@ early_init(int r3, int r4, int r5)
 	identify_cpu(offset, 0);
 	do_cpu_ftr_fixups(offset);
 
-#if defined(CONFIG_PPC_MULTIPLATFORM)
+#if defined(CONFIG_PPC_OF)
 	reloc_got2(offset);
 
-	/* If we came here from BootX, clear the screen,
-	 * set up some pointers and return. */
-	if ((r3 == 0x426f6f58) && (r5 == 0))
-		bootx_init(r4, phys);
-
 	/*
 	 * don't do anything on prep
 	 * for now, don't use bootinfo because it breaks yaboot 0.5
 	 * and assume that if we didn't find a magic number, we have OF
 	 */
-	else if (*(unsigned long *)(0) != 0xdeadc0de)
+	if (*(unsigned long *)(0) != 0xdeadc0de)
 		phys = prom_init(r3, r4, (prom_entry)r5);
 
 	reloc_got2(-offset);
@@ -424,6 +415,7 @@ platform_init(unsigned long r3, unsigned long r4, unsigned long r5,
 	}
 #endif
 
+#ifdef CONFIG_PPC_OF
 	have_of = 1;
 
 	/* prom_init has already been called from __start */
@@ -495,19 +487,17 @@ platform_init(unsigned long r3, unsigned long r4, unsigned long r5,
 #endif /* CONFIG_ADB */
 
 	switch (_machine) {
-#ifdef CONFIG_PPC_PMAC
-	case _MACH_Pmac:
-		pmac_init(r3, r4, r5, r6, r7);
-		break;
-#endif
 #ifdef CONFIG_PPC_CHRP
 	case _MACH_chrp:
 		chrp_init(r3, r4, r5, r6, r7);
 		break;
 #endif
 	}
+#endif /* CONFIG_PPC_OF */
 }
+#endif /* CONFIG_PPC_MULTIPLATFORM */
 
+#ifdef CONFIG_PPC_OF
 #ifdef CONFIG_SERIAL_CORE_CONSOLE
 extern char *of_stdout_device;
 
@@ -564,7 +554,7 @@ static int __init set_preferred_console(void)
 }
 console_initcall(set_preferred_console);
 #endif /* CONFIG_SERIAL_CORE_CONSOLE */
-#endif /* CONFIG_PPC_MULTIPLATFORM */
+#endif /* CONFIG_PPC_OF */
 
 struct bi_record *find_bootinfo(void)
 {
@@ -747,14 +737,6 @@ void __init setup_arch(char **cmdline_p)
 	if (ppc_md.init_early)
 		ppc_md.init_early();
 
-#ifdef CONFIG_PPC_MULTIPLATFORM
-	/* This could be called "early setup arch", it must be done
-	 * now because xmon need it
-	 */
-	if (_machine == _MACH_Pmac)
-		pmac_feature_init();	/* New cool way */
-#endif
-
 #ifdef CONFIG_XMON
 	xmon_init(1);
 	if (strstr(cmd_line, "xmon"))
diff --git a/arch/ppc/kernel/traps.c b/arch/ppc/kernel/traps.c
index 9dbc4d28fa2..6d0a1838d94 100644
--- a/arch/ppc/kernel/traps.c
+++ b/arch/ppc/kernel/traps.c
@@ -38,9 +38,6 @@
 #include <asm/io.h>
 #include <asm/reg.h>
 #include <asm/xmon.h>
-#ifdef CONFIG_PMAC_BACKLIGHT
-#include <asm/backlight.h>
-#endif
 #include <asm/pmc.h>
 
 #ifdef CONFIG_XMON
@@ -85,12 +82,6 @@ int die(const char * str, struct pt_regs * fp, long err)
 	int nl = 0;
 	console_verbose();
 	spin_lock_irq(&die_lock);
-#ifdef CONFIG_PMAC_BACKLIGHT
-	if (_machine == _MACH_Pmac) {
-		set_backlight_enable(1);
-		set_backlight_level(BACKLIGHT_MAX);
-	}
-#endif
 	printk("Oops: %s, sig: %ld [#%d]\n", str, err, ++die_counter);
 #ifdef CONFIG_PREEMPT
 	printk("PREEMPT ");
@@ -159,7 +150,7 @@ void _exception(int signr, struct pt_regs *regs, int code, unsigned long addr)
  */
 static inline int check_io_access(struct pt_regs *regs)
 {
-#if defined CONFIG_PPC_PMAC || defined CONFIG_8xx
+#if defined CONFIG_8xx
 	unsigned long msr = regs->msr;
 	const struct exception_table_entry *entry;
 	unsigned int *nip = (unsigned int *)regs->nip;
@@ -196,7 +187,7 @@ static inline int check_io_access(struct pt_regs *regs)
 			return 1;
 		}
 	}
-#endif /* CONFIG_PPC_PMAC */
+#endif /* CONFIG_8xx */
 	return 0;
 }
 
diff --git a/arch/ppc/mm/init.c b/arch/ppc/mm/init.c
index 45f0782059f..134db5c0420 100644
--- a/arch/ppc/mm/init.c
+++ b/arch/ppc/mm/init.c
@@ -67,10 +67,6 @@ unsigned long ppc_memoffset = PAGE_OFFSET;
 int mem_init_done;
 int init_bootmem_done;
 int boot_mapsize;
-#ifdef CONFIG_PPC_PMAC
-unsigned long agp_special_page;
-EXPORT_SYMBOL(agp_special_page);
-#endif
 
 extern char _end[];
 extern char etext[], _stext[];
@@ -424,10 +420,6 @@ void __init mem_init(void)
 		     addr += PAGE_SIZE)
 			SetPageReserved(virt_to_page(addr));
 #endif
-#ifdef CONFIG_PPC_PMAC
-	if (agp_special_page)
-		SetPageReserved(virt_to_page(agp_special_page));
-#endif
 	for (addr = PAGE_OFFSET; addr < (unsigned long)high_memory;
 	     addr += PAGE_SIZE) {
 		if (!PageReserved(virt_to_page(addr)))
@@ -463,11 +455,6 @@ void __init mem_init(void)
 	       initpages<< (PAGE_SHIFT-10),
 	       (unsigned long) (totalhigh_pages << (PAGE_SHIFT-10)));
 
-#ifdef CONFIG_PPC_PMAC
-	if (agp_special_page)
-		printk(KERN_INFO "AGP special page: 0x%08lx\n", agp_special_page);
-#endif
-
 	mem_init_done = 1;
 }
 
@@ -512,22 +499,6 @@ set_phys_avail(unsigned long total_memory)
 	if (rtas_data)
 		mem_pieces_remove(&phys_avail, rtas_data, rtas_size, 1);
 #endif
-#ifdef CONFIG_PPC_PMAC
-	/* Because of some uninorth weirdness, we need a page of
-	 * memory as high as possible (it must be outside of the
-	 * bus address seen as the AGP aperture). It will be used
-	 * by the r128 DRM driver
-	 *
-	 * FIXME: We need to make sure that page doesn't overlap any of the\
-	 * above. This could be done by improving mem_pieces_find to be able
-	 * to do a backward search from the end of the list.
-	 */
-	if (_machine == _MACH_Pmac && find_devices("uni-north-agp")) {
-		agp_special_page = (total_memory - PAGE_SIZE);
-		mem_pieces_remove(&phys_avail, agp_special_page, PAGE_SIZE, 0);
-		agp_special_page = (unsigned long)__va(agp_special_page);
-	}
-#endif /* CONFIG_PPC_PMAC */
 }
 
 /* Mark some memory as reserved by removing it from phys_avail. */
diff --git a/arch/ppc/platforms/Makefile b/arch/ppc/platforms/Makefile
index 7c5cdabf6f3..51430e294b3 100644
--- a/arch/ppc/platforms/Makefile
+++ b/arch/ppc/platforms/Makefile
@@ -3,26 +3,18 @@
 #
 
 # Extra CFLAGS so we don't have to do relative includes
-CFLAGS_pmac_setup.o	+= -Iarch/$(ARCH)/mm
+CFLAGS_chrp_setup.o	+= -Iarch/$(ARCH)/mm
 
 obj-$(CONFIG_APUS)		+= apus_setup.o
 ifeq ($(CONFIG_APUS),y)
 obj-$(CONFIG_PCI)		+= apus_pci.o
 endif
-obj-$(CONFIG_PPC_PMAC)		+= pmac_pic.o pmac_setup.o pmac_time.o \
-					pmac_feature.o pmac_pci.o pmac_sleep.o \
-					pmac_low_i2c.o pmac_cache.o
 obj-$(CONFIG_PPC_CHRP)		+= chrp_setup.o chrp_time.o chrp_pci.o \
 					chrp_pegasos_eth.o
 ifeq ($(CONFIG_PPC_CHRP),y)
 obj-$(CONFIG_NVRAM)		+= chrp_nvram.o
 endif
 obj-$(CONFIG_PPC_PREP)		+= prep_pci.o prep_setup.o
-ifeq ($(CONFIG_PPC_PMAC),y)
-obj-$(CONFIG_NVRAM)		+= pmac_nvram.o
-obj-$(CONFIG_CPU_FREQ_PMAC)	+= pmac_cpufreq.o
-endif
-obj-$(CONFIG_PMAC_BACKLIGHT)	+= pmac_backlight.o
 obj-$(CONFIG_PREP_RESIDUAL)	+= residual.o
 obj-$(CONFIG_PQ2ADS)		+= pq2ads.o
 obj-$(CONFIG_TQM8260)		+= tqm8260_setup.o
@@ -47,6 +39,5 @@ obj-$(CONFIG_LITE5200)		+= lite5200.o
 obj-$(CONFIG_EV64360)		+= ev64360.o
 
 ifeq ($(CONFIG_SMP),y)
-obj-$(CONFIG_PPC_PMAC)		+= pmac_smp.o
 obj-$(CONFIG_PPC_CHRP)		+= chrp_smp.o
 endif
diff --git a/arch/ppc/platforms/chrp_pci.c b/arch/ppc/platforms/chrp_pci.c
index bd047aac01b..c7fe6182bb7 100644
--- a/arch/ppc/platforms/chrp_pci.c
+++ b/arch/ppc/platforms/chrp_pci.c
@@ -275,7 +275,7 @@ chrp_find_bridges(void)
 			setup_python(hose, dev);
 		} else if (is_mot
 			   || strncmp(model, "Motorola, Grackle", 17) == 0) {
-			setup_grackle(hose);
+			setup_indirect_pci(hose, 0xfec00000, 0xfee00000);
 		} else if (is_longtrail) {
 			void __iomem *p = ioremap(GG2_PCI_CONFIG_BASE, 0x80000);
 			hose->ops = &gg2_pci_ops;
diff --git a/arch/ppc/platforms/chrp_setup.c b/arch/ppc/platforms/chrp_setup.c
index 056ac2a7b5c..48996b78737 100644
--- a/arch/ppc/platforms/chrp_setup.c
+++ b/arch/ppc/platforms/chrp_setup.c
@@ -53,6 +53,7 @@
 #include <asm/i8259.h>
 #include <asm/open_pic.h>
 #include <asm/xmon.h>
+#include "mem_pieces.h"
 
 unsigned long chrp_get_rtc_time(void);
 int chrp_set_rtc_time(unsigned long nowtime);
@@ -65,7 +66,6 @@ void rtas_display_progress(char *, unsigned short);
 void rtas_indicator_progress(char *, unsigned short);
 void btext_progress(char *, unsigned short);
 
-extern unsigned long pmac_find_end_of_memory(void);
 extern int of_show_percpuinfo(struct seq_file *, int);
 
 int _chrp_type;
@@ -467,6 +467,75 @@ chrp_init2(void)
 		ppc_md.progress("  Have fun!    ", 0x7777);
 }
 
+static struct device_node *memory_node;
+
+static int __init get_mem_prop(char *name, struct mem_pieces *mp)
+{
+	struct reg_property *rp;
+	int i, s;
+	unsigned int *ip;
+	int nac = prom_n_addr_cells(memory_node);
+	int nsc = prom_n_size_cells(memory_node);
+
+	ip = (unsigned int *) get_property(memory_node, name, &s);
+	if (ip == NULL) {
+		printk(KERN_ERR "error: couldn't get %s property on /memory\n",
+		       name);
+		return 0;
+	}
+	s /= (nsc + nac) * 4;
+	rp = mp->regions;
+	for (i = 0; i < s; ++i, ip += nac+nsc) {
+		if (nac >= 2 && ip[nac-2] != 0)
+			continue;
+		rp->address = ip[nac-1];
+		if (nsc >= 2 && ip[nac+nsc-2] != 0)
+			rp->size = ~0U;
+		else
+			rp->size = ip[nac+nsc-1];
+		++rp;
+	}
+	mp->n_regions = rp - mp->regions;
+
+	/* Make sure the pieces are sorted. */
+	mem_pieces_sort(mp);
+	mem_pieces_coalesce(mp);
+	return 1;
+}
+
+static unsigned long __init chrp_find_end_of_memory(void)
+{
+	unsigned long a, total;
+	struct mem_pieces phys_mem;
+
+	/*
+	 * Find out where physical memory is, and check that it
+	 * starts at 0 and is contiguous.  It seems that RAM is
+	 * always physically contiguous on Power Macintoshes.
+	 *
+	 * Supporting discontiguous physical memory isn't hard,
+	 * it just makes the virtual <-> physical mapping functions
+	 * more complicated (or else you end up wasting space
+	 * in mem_map).
+	 */
+	memory_node = find_devices("memory");
+	if (memory_node == NULL || !get_mem_prop("reg", &phys_mem)
+	    || phys_mem.n_regions == 0)
+		panic("No RAM??");
+	a = phys_mem.regions[0].address;
+	if (a != 0)
+		panic("RAM doesn't start at physical address 0");
+	total = phys_mem.regions[0].size;
+
+	if (phys_mem.n_regions > 1) {
+		printk("RAM starting at 0x%x is not contiguous\n",
+		       phys_mem.regions[1].address);
+		printk("Using RAM from 0 to 0x%lx\n", total-1);
+	}
+
+	return total;
+}
+
 void __init
 chrp_init(unsigned long r3, unsigned long r4, unsigned long r5,
 	  unsigned long r6, unsigned long r7)
@@ -525,7 +594,7 @@ chrp_init(unsigned long r3, unsigned long r4, unsigned long r5,
 	ppc_md.get_rtc_time   = chrp_get_rtc_time;
 	ppc_md.calibrate_decr = chrp_calibrate_decr;
 
-	ppc_md.find_end_of_memory = pmac_find_end_of_memory;
+	ppc_md.find_end_of_memory = chrp_find_end_of_memory;
 
 	if (rtas_data) {
 		struct device_node *rtas;
diff --git a/arch/ppc/platforms/chrp_time.c b/arch/ppc/platforms/chrp_time.c
index 29d074c305f..57753a55b58 100644
--- a/arch/ppc/platforms/chrp_time.c
+++ b/arch/ppc/platforms/chrp_time.c
@@ -163,13 +163,75 @@ unsigned long chrp_get_rtc_time(void)
 	return mktime(year, mon, day, hour, min, sec);
 }
 
+/*
+ * Calibrate the decrementer frequency with the VIA timer 1.
+ */
+#define VIA_TIMER_FREQ_6	4700000	/* time 1 frequency * 6 */
+
+/* VIA registers */
+#define RS		0x200		/* skip between registers */
+#define T1CL		(4*RS)		/* Timer 1 ctr/latch (low 8 bits) */
+#define T1CH		(5*RS)		/* Timer 1 counter (high 8 bits) */
+#define T1LL		(6*RS)		/* Timer 1 latch (low 8 bits) */
+#define T1LH		(7*RS)		/* Timer 1 latch (high 8 bits) */
+#define ACR		(11*RS)		/* Auxiliary control register */
+#define IFR		(13*RS)		/* Interrupt flag register */
+
+/* Bits in ACR */
+#define T1MODE		0xc0		/* Timer 1 mode */
+#define T1MODE_CONT	0x40		/*  continuous interrupts */
+
+/* Bits in IFR and IER */
+#define T1_INT		0x40		/* Timer 1 interrupt */
+
+static int __init chrp_via_calibrate_decr(void)
+{
+	struct device_node *vias;
+	volatile unsigned char __iomem *via;
+	int count = VIA_TIMER_FREQ_6 / 100;
+	unsigned int dstart, dend;
+
+	vias = find_devices("via-cuda");
+	if (vias == 0)
+		vias = find_devices("via");
+	if (vias == 0 || vias->n_addrs == 0)
+		return 0;
+	via = ioremap(vias->addrs[0].address, vias->addrs[0].size);
+
+	/* set timer 1 for continuous interrupts */
+	out_8(&via[ACR], (via[ACR] & ~T1MODE) | T1MODE_CONT);
+	/* set the counter to a small value */
+	out_8(&via[T1CH], 2);
+	/* set the latch to `count' */
+	out_8(&via[T1LL], count);
+	out_8(&via[T1LH], count >> 8);
+	/* wait until it hits 0 */
+	while ((in_8(&via[IFR]) & T1_INT) == 0)
+		;
+	dstart = get_dec();
+	/* clear the interrupt & wait until it hits 0 again */
+	in_8(&via[T1CL]);
+	while ((in_8(&via[IFR]) & T1_INT) == 0)
+		;
+	dend = get_dec();
+
+	tb_ticks_per_jiffy = (dstart - dend) / ((6 * HZ)/100);
+	tb_to_us = mulhwu_scale_factor(dstart - dend, 60000);
+
+	printk(KERN_INFO "via_calibrate_decr: ticks per jiffy = %u (%u ticks)\n",
+	       tb_ticks_per_jiffy, dstart - dend);
+
+	iounmap(via);
+	
+	return 1;
+}
 
 void __init chrp_calibrate_decr(void)
 {
 	struct device_node *cpu;
 	unsigned int freq, *fp;
 
-	if (via_calibrate_decr())
+	if (chrp_via_calibrate_decr())
 		return;
 
 	/*
diff --git a/arch/ppc/platforms/pmac_backlight.c b/arch/ppc/platforms/pmac_backlight.c
deleted file mode 100644
index 8be2f7d071f..00000000000
--- a/arch/ppc/platforms/pmac_backlight.c
+++ /dev/null
@@ -1,202 +0,0 @@
-/*
- * Miscellaneous procedures for dealing with the PowerMac hardware.
- * Contains support for the backlight.
- *
- *   Copyright (C) 2000 Benjamin Herrenschmidt
- *
- */
-
-#include <linux/config.h>
-#include <linux/kernel.h>
-#include <linux/module.h>
-#include <linux/stddef.h>
-#include <linux/reboot.h>
-#include <linux/nvram.h>
-#include <linux/console.h>
-#include <asm/sections.h>
-#include <asm/ptrace.h>
-#include <asm/io.h>
-#include <asm/pgtable.h>
-#include <asm/system.h>
-#include <asm/prom.h>
-#include <asm/machdep.h>
-#include <asm/nvram.h>
-#include <asm/backlight.h>
-
-#include <linux/adb.h>
-#include <linux/pmu.h>
-
-static struct backlight_controller *backlighter;
-static void* backlighter_data;
-static int backlight_autosave;
-static int backlight_level = BACKLIGHT_MAX;
-static int backlight_enabled = 1;
-static int backlight_req_level = -1;
-static int backlight_req_enable = -1;
-
-static void backlight_callback(void *);
-static DECLARE_WORK(backlight_work, backlight_callback, NULL);
-
-void register_backlight_controller(struct backlight_controller *ctrler,
-					  void *data, char *type)
-{
-	struct device_node* bk_node;
-	char *prop;
-	int valid = 0;
-
-	/* There's already a matching controller, bail out */
-	if (backlighter != NULL)
-		return;
-
-	bk_node = find_devices("backlight");
-
-#ifdef CONFIG_ADB_PMU
-	/* Special case for the old PowerBook since I can't test on it */
-	backlight_autosave = machine_is_compatible("AAPL,3400/2400")
-		|| machine_is_compatible("AAPL,3500");
-	if ((backlight_autosave
-	     || machine_is_compatible("AAPL,PowerBook1998")
-	     || machine_is_compatible("PowerBook1,1"))
-	    && !strcmp(type, "pmu"))
-		valid = 1;
-#endif
-	if (bk_node) {
-		prop = get_property(bk_node, "backlight-control", NULL);
-		if (prop && !strncmp(prop, type, strlen(type)))
-			valid = 1;
-	}
-	if (!valid)
-		return;
-	backlighter = ctrler;
-	backlighter_data = data;
-
-	if (bk_node && !backlight_autosave)
-		prop = get_property(bk_node, "bklt", NULL);
-	else
-		prop = NULL;
-	if (prop) {
-		backlight_level = ((*prop)+1) >> 1;
-		if (backlight_level > BACKLIGHT_MAX)
-			backlight_level = BACKLIGHT_MAX;
-	}
-
-#ifdef CONFIG_ADB_PMU
-	if (backlight_autosave) {
-		struct adb_request req;
-		pmu_request(&req, NULL, 2, 0xd9, 0);
-		while (!req.complete)
-			pmu_poll();
-		backlight_level = req.reply[0] >> 4;
-	}
-#endif
-	acquire_console_sem();
-	if (!backlighter->set_enable(1, backlight_level, data))
-		backlight_enabled = 1;
-	release_console_sem();
-
-	printk(KERN_INFO "Registered \"%s\" backlight controller,"
-	       "level: %d/15\n", type, backlight_level);
-}
-EXPORT_SYMBOL(register_backlight_controller);
-
-void unregister_backlight_controller(struct backlight_controller
-					    *ctrler, void *data)
-{
-	/* We keep the current backlight level (for now) */
-	if (ctrler == backlighter && data == backlighter_data)
-		backlighter = NULL;
-}
-EXPORT_SYMBOL(unregister_backlight_controller);
-
-static int __set_backlight_enable(int enable)
-{
-	int rc;
-
-	if (!backlighter)
-		return -ENODEV;
-	acquire_console_sem();
-	rc = backlighter->set_enable(enable, backlight_level,
-				     backlighter_data);
-	if (!rc)
-		backlight_enabled = enable;
-	release_console_sem();
-	return rc;
-}
-int set_backlight_enable(int enable)
-{
-	if (!backlighter)
-		return -ENODEV;
-	backlight_req_enable = enable;
-	schedule_work(&backlight_work);
-	return 0;
-}
-
-EXPORT_SYMBOL(set_backlight_enable);
-
-int get_backlight_enable(void)
-{
-	if (!backlighter)
-		return -ENODEV;
-	return backlight_enabled;
-}
-EXPORT_SYMBOL(get_backlight_enable);
-
-static int __set_backlight_level(int level)
-{
-	int rc = 0;
-
-	if (!backlighter)
-		return -ENODEV;
-	if (level < BACKLIGHT_MIN)
-		level = BACKLIGHT_OFF;
-	if (level > BACKLIGHT_MAX)
-		level = BACKLIGHT_MAX;
-	acquire_console_sem();
-	if (backlight_enabled)
-		rc = backlighter->set_level(level, backlighter_data);
-	if (!rc)
-		backlight_level = level;
-	release_console_sem();
-	if (!rc && !backlight_autosave) {
-		level <<=1;
-		if (level & 0x10)
-			level |= 0x01;
-		// -- todo: save to property "bklt"
-	}
-	return rc;
-}
-int set_backlight_level(int level)
-{
-	if (!backlighter)
-		return -ENODEV;
-	backlight_req_level = level;
-	schedule_work(&backlight_work);
-	return 0;
-}
-
-EXPORT_SYMBOL(set_backlight_level);
-
-int get_backlight_level(void)
-{
-	if (!backlighter)
-		return -ENODEV;
-	return backlight_level;
-}
-EXPORT_SYMBOL(get_backlight_level);
-
-static void backlight_callback(void *dummy)
-{
-	int level, enable;
-
-	do {
-		level = backlight_req_level;
-		enable = backlight_req_enable;
-		mb();
-
-		if (level >= 0)
-			__set_backlight_level(level);
-		if (enable >= 0)
-			__set_backlight_enable(enable);
-	} while(cmpxchg(&backlight_req_level, level, -1) != level ||
-		cmpxchg(&backlight_req_enable, enable, -1) != enable);
-}
diff --git a/arch/ppc/platforms/pmac_cache.S b/arch/ppc/platforms/pmac_cache.S
deleted file mode 100644
index fb977de6b70..00000000000
--- a/arch/ppc/platforms/pmac_cache.S
+++ /dev/null
@@ -1,359 +0,0 @@
-/*
- * This file contains low-level cache management functions
- * used for sleep and CPU speed changes on Apple machines.
- * (In fact the only thing that is Apple-specific is that we assume
- * that we can read from ROM at physical address 0xfff00000.)
- *
- *    Copyright (C) 2004 Paul Mackerras (paulus@samba.org) and
- *                       Benjamin Herrenschmidt (benh@kernel.crashing.org)
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License
- * as published by the Free Software Foundation; either version
- * 2 of the License, or (at your option) any later version.
- *
- */
-
-#include <linux/config.h>
-#include <asm/processor.h>
-#include <asm/ppc_asm.h>
-#include <asm/cputable.h>
-
-/*
- * Flush and disable all data caches (dL1, L2, L3). This is used
- * when going to sleep, when doing a PMU based cpufreq transition,
- * or when "offlining" a CPU on SMP machines. This code is over
- * paranoid, but I've had enough issues with various CPU revs and
- * bugs that I decided it was worth beeing over cautious
- */
-
-_GLOBAL(flush_disable_caches)
-#ifndef CONFIG_6xx
-	blr
-#else
-BEGIN_FTR_SECTION
-	b	flush_disable_745x
-END_FTR_SECTION_IFSET(CPU_FTR_SPEC7450)
-BEGIN_FTR_SECTION
-	b	flush_disable_75x
-END_FTR_SECTION_IFSET(CPU_FTR_L2CR)
-	b	__flush_disable_L1
-
-/* This is the code for G3 and 74[01]0 */
-flush_disable_75x:
-	mflr	r10
-
-	/* Turn off EE and DR in MSR */
-	mfmsr	r11
-	rlwinm	r0,r11,0,~MSR_EE
-	rlwinm	r0,r0,0,~MSR_DR
-	sync
-	mtmsr	r0
-	isync
-
-	/* Stop DST streams */
-BEGIN_FTR_SECTION
-	DSSALL
-	sync
-END_FTR_SECTION_IFSET(CPU_FTR_ALTIVEC)
-
-	/* Stop DPM */
-	mfspr	r8,SPRN_HID0		/* Save SPRN_HID0 in r8 */
-	rlwinm	r4,r8,0,12,10		/* Turn off HID0[DPM] */
-	sync
-	mtspr	SPRN_HID0,r4		/* Disable DPM */
-	sync
-
-	/* Disp-flush L1. We have a weird problem here that I never
-	 * totally figured out. On 750FX, using the ROM for the flush
-	 * results in a non-working flush. We use that workaround for
-	 * now until I finally understand what's going on. --BenH
-	 */
-
-	/* ROM base by default */
-	lis	r4,0xfff0
-	mfpvr	r3
-	srwi	r3,r3,16
-	cmplwi	cr0,r3,0x7000
-	bne+	1f
-	/* RAM base on 750FX */
-	li	r4,0
-1:	li	r4,0x4000
-	mtctr	r4
-1:	lwz	r0,0(r4)
-	addi	r4,r4,32
-	bdnz	1b
-	sync
-	isync
-
-	/* Disable / invalidate / enable L1 data */
-	mfspr	r3,SPRN_HID0
-	rlwinm	r3,r3,0,~(HID0_DCE | HID0_ICE)
-	mtspr	SPRN_HID0,r3
-	sync
-	isync
-	ori	r3,r3,(HID0_DCE|HID0_DCI|HID0_ICE|HID0_ICFI)
-	sync
-	isync
-	mtspr	SPRN_HID0,r3
-	xori	r3,r3,(HID0_DCI|HID0_ICFI)
-	mtspr	SPRN_HID0,r3
-	sync
-
-	/* Get the current enable bit of the L2CR into r4 */
-	mfspr	r5,SPRN_L2CR
-	/* Set to data-only (pre-745x bit) */
-	oris	r3,r5,L2CR_L2DO@h
-	b	2f
-	/* When disabling L2, code must be in L1 */
-	.balign 32
-1:	mtspr	SPRN_L2CR,r3
-3:	sync
-	isync
-	b	1f
-2:	b	3f
-3:	sync
-	isync
-	b	1b
-1:	/* disp-flush L2. The interesting thing here is that the L2 can be
-	 * up to 2Mb ... so using the ROM, we'll end up wrapping back to memory
-	 * but that is probbaly fine. We disp-flush over 4Mb to be safe
-	 */
-	lis	r4,2
-	mtctr	r4
-	lis	r4,0xfff0
-1:	lwz	r0,0(r4)
-	addi	r4,r4,32
-	bdnz	1b
-	sync
-	isync
-	lis	r4,2
-	mtctr	r4
-	lis	r4,0xfff0
-1:	dcbf	0,r4
-	addi	r4,r4,32
-	bdnz	1b
-	sync
-	isync
-
-	/* now disable L2 */
-	rlwinm	r5,r5,0,~L2CR_L2E
-	b	2f
-	/* When disabling L2, code must be in L1 */
-	.balign 32
-1:	mtspr	SPRN_L2CR,r5
-3:	sync
-	isync
-	b	1f
-2:	b	3f
-3:	sync
-	isync
-	b	1b
-1:	sync
-	isync
-	/* Invalidate L2. This is pre-745x, we clear the L2I bit ourselves */
-	oris	r4,r5,L2CR_L2I@h
-	mtspr	SPRN_L2CR,r4
-	sync
-	isync
-
-	/* Wait for the invalidation to complete */
-1:	mfspr	r3,SPRN_L2CR
-	rlwinm.	r0,r3,0,31,31
-	bne	1b
-
-	/* Clear L2I */
-	xoris	r4,r4,L2CR_L2I@h
-	sync
-	mtspr	SPRN_L2CR,r4
-	sync
-
-	/* now disable the L1 data cache */
-	mfspr	r0,SPRN_HID0
-	rlwinm	r0,r0,0,~(HID0_DCE|HID0_ICE)
-	mtspr	SPRN_HID0,r0
-	sync
-	isync
-
-	/* Restore HID0[DPM] to whatever it was before */
-	sync
-	mfspr	r0,SPRN_HID0
-	rlwimi	r0,r8,0,11,11		/* Turn back HID0[DPM] */
-	mtspr	SPRN_HID0,r0
-	sync
-
-	/* restore DR and EE */
-	sync
-	mtmsr	r11
-	isync
-
-	mtlr	r10
-	blr
-
-/* This code is for 745x processors */
-flush_disable_745x:
-	/* Turn off EE and DR in MSR */
-	mfmsr	r11
-	rlwinm	r0,r11,0,~MSR_EE
-	rlwinm	r0,r0,0,~MSR_DR
-	sync
-	mtmsr	r0
-	isync
-
-	/* Stop prefetch streams */
-	DSSALL
-	sync
-
-	/* Disable L2 prefetching */
-	mfspr	r0,SPRN_MSSCR0
-	rlwinm	r0,r0,0,0,29
-	mtspr	SPRN_MSSCR0,r0
-	sync
-	isync
-	lis	r4,0
-	dcbf	0,r4
-	dcbf	0,r4
-	dcbf	0,r4
-	dcbf	0,r4
-	dcbf	0,r4
-	dcbf	0,r4
-	dcbf	0,r4
-	dcbf	0,r4
-
-	/* Due to a bug with the HW flush on some CPU revs, we occasionally
-	 * experience data corruption. I'm adding a displacement flush along
-	 * with a dcbf loop over a few Mb to "help". The problem isn't totally
-	 * fixed by this in theory, but at least, in practice, I couldn't reproduce
-	 * it even with a big hammer...
-	 */
-
-        lis     r4,0x0002
-        mtctr   r4
- 	li      r4,0
-1:
-        lwz     r0,0(r4)
-        addi    r4,r4,32                /* Go to start of next cache line */
-        bdnz    1b
-        isync
-
-        /* Now, flush the first 4MB of memory */
-        lis     r4,0x0002
-        mtctr   r4
-	li      r4,0
-        sync
-1:
-        dcbf    0,r4
-        addi    r4,r4,32                /* Go to start of next cache line */
-        bdnz    1b
-
-	/* Flush and disable the L1 data cache */
-	mfspr	r6,SPRN_LDSTCR
-	lis	r3,0xfff0	/* read from ROM for displacement flush */
-	li	r4,0xfe		/* start with only way 0 unlocked */
-	li	r5,128		/* 128 lines in each way */
-1:	mtctr	r5
-	rlwimi	r6,r4,0,24,31
-	mtspr	SPRN_LDSTCR,r6
-	sync
-	isync
-2:	lwz	r0,0(r3)	/* touch each cache line */
-	addi	r3,r3,32
-	bdnz	2b
-	rlwinm	r4,r4,1,24,30	/* move on to the next way */
-	ori	r4,r4,1
-	cmpwi	r4,0xff		/* all done? */
-	bne	1b
-	/* now unlock the L1 data cache */
-	li	r4,0
-	rlwimi	r6,r4,0,24,31
-	sync
-	mtspr	SPRN_LDSTCR,r6
-	sync
-	isync
-
-	/* Flush the L2 cache using the hardware assist */
-	mfspr	r3,SPRN_L2CR
-	cmpwi	r3,0		/* check if it is enabled first */
-	bge	4f
-	oris	r0,r3,(L2CR_L2IO_745x|L2CR_L2DO_745x)@h
-	b	2f
-	/* When disabling/locking L2, code must be in L1 */
-	.balign 32
-1:	mtspr	SPRN_L2CR,r0	/* lock the L2 cache */
-3:	sync
-	isync
-	b	1f
-2:	b	3f
-3:	sync
-	isync
-	b	1b
-1:	sync
-	isync
-	ori	r0,r3,L2CR_L2HWF_745x
-	sync
-	mtspr	SPRN_L2CR,r0	/* set the hardware flush bit */
-3:	mfspr	r0,SPRN_L2CR	/* wait for it to go to 0 */
-	andi.	r0,r0,L2CR_L2HWF_745x
-	bne	3b
-	sync
-	rlwinm	r3,r3,0,~L2CR_L2E
-	b	2f
-	/* When disabling L2, code must be in L1 */
-	.balign 32
-1:	mtspr	SPRN_L2CR,r3	/* disable the L2 cache */
-3:	sync
-	isync
-	b	1f
-2:	b	3f
-3:	sync
-	isync
-	b	1b
-1:	sync
-	isync
-	oris	r4,r3,L2CR_L2I@h
-	mtspr	SPRN_L2CR,r4
-	sync
-	isync
-1:	mfspr	r4,SPRN_L2CR
-	andis.	r0,r4,L2CR_L2I@h
-	bne	1b
-	sync
-
-BEGIN_FTR_SECTION
-	/* Flush the L3 cache using the hardware assist */
-4:	mfspr	r3,SPRN_L3CR
-	cmpwi	r3,0		/* check if it is enabled */
-	bge	6f
-	oris	r0,r3,L3CR_L3IO@h
-	ori	r0,r0,L3CR_L3DO
-	sync
-	mtspr	SPRN_L3CR,r0	/* lock the L3 cache */
-	sync
-	isync
-	ori	r0,r0,L3CR_L3HWF
-	sync
-	mtspr	SPRN_L3CR,r0	/* set the hardware flush bit */
-5:	mfspr	r0,SPRN_L3CR	/* wait for it to go to zero */
-	andi.	r0,r0,L3CR_L3HWF
-	bne	5b
-	rlwinm	r3,r3,0,~L3CR_L3E
-	sync
-	mtspr	SPRN_L3CR,r3	/* disable the L3 cache */
-	sync
-	ori	r4,r3,L3CR_L3I
-	mtspr	SPRN_L3CR,r4
-1:	mfspr	r4,SPRN_L3CR
-	andi.	r0,r4,L3CR_L3I
-	bne	1b
-	sync
-END_FTR_SECTION_IFSET(CPU_FTR_L3CR)
-
-6:	mfspr	r0,SPRN_HID0	/* now disable the L1 data cache */
-	rlwinm	r0,r0,0,~HID0_DCE
-	mtspr	SPRN_HID0,r0
-	sync
-	isync
-	mtmsr	r11		/* restore DR and EE */
-	isync
-	blr
-#endif	/* CONFIG_6xx */
diff --git a/arch/ppc/platforms/pmac_cpufreq.c b/arch/ppc/platforms/pmac_cpufreq.c
deleted file mode 100644
index fba7e4d7c0b..00000000000
--- a/arch/ppc/platforms/pmac_cpufreq.c
+++ /dev/null
@@ -1,735 +0,0 @@
-/*
- *  arch/ppc/platforms/pmac_cpufreq.c
- *
- *  Copyright (C) 2002 - 2005 Benjamin Herrenschmidt <benh@kernel.crashing.org>
- *  Copyright (C) 2004        John Steele Scott <toojays@toojays.net>
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
- *
- * TODO: Need a big cleanup here. Basically, we need to have different
- * cpufreq_driver structures for the different type of HW instead of the
- * current mess. We also need to better deal with the detection of the
- * type of machine.
- *
- */
-
-#include <linux/config.h>
-#include <linux/module.h>
-#include <linux/types.h>
-#include <linux/errno.h>
-#include <linux/kernel.h>
-#include <linux/delay.h>
-#include <linux/sched.h>
-#include <linux/adb.h>
-#include <linux/pmu.h>
-#include <linux/slab.h>
-#include <linux/cpufreq.h>
-#include <linux/init.h>
-#include <linux/sysdev.h>
-#include <linux/i2c.h>
-#include <linux/hardirq.h>
-#include <asm/prom.h>
-#include <asm/machdep.h>
-#include <asm/irq.h>
-#include <asm/pmac_feature.h>
-#include <asm/mmu_context.h>
-#include <asm/sections.h>
-#include <asm/cputable.h>
-#include <asm/time.h>
-#include <asm/system.h>
-#include <asm/open_pic.h>
-#include <asm/keylargo.h>
-
-/* WARNING !!! This will cause calibrate_delay() to be called,
- * but this is an __init function ! So you MUST go edit
- * init/main.c to make it non-init before enabling DEBUG_FREQ
- */
-#undef DEBUG_FREQ
-
-/*
- * There is a problem with the core cpufreq code on SMP kernels,
- * it won't recalculate the Bogomips properly
- */
-#ifdef CONFIG_SMP
-#warning "WARNING, CPUFREQ not recommended on SMP kernels"
-#endif
-
-extern void low_choose_7447a_dfs(int dfs);
-extern void low_choose_750fx_pll(int pll);
-extern void low_sleep_handler(void);
-
-/*
- * Currently, PowerMac cpufreq supports only high & low frequencies
- * that are set by the firmware
- */
-static unsigned int low_freq;
-static unsigned int hi_freq;
-static unsigned int cur_freq;
-static unsigned int sleep_freq;
-
-/*
- * Different models uses different mecanisms to switch the frequency
- */
-static int (*set_speed_proc)(int low_speed);
-static unsigned int (*get_speed_proc)(void);
-
-/*
- * Some definitions used by the various speedprocs
- */
-static u32 voltage_gpio;
-static u32 frequency_gpio;
-static u32 slew_done_gpio;
-static int no_schedule;
-static int has_cpu_l2lve;
-static int is_pmu_based;
-
-/* There are only two frequency states for each processor. Values
- * are in kHz for the time being.
- */
-#define CPUFREQ_HIGH                  0
-#define CPUFREQ_LOW                   1
-
-static struct cpufreq_frequency_table pmac_cpu_freqs[] = {
-	{CPUFREQ_HIGH, 		0},
-	{CPUFREQ_LOW,		0},
-	{0,			CPUFREQ_TABLE_END},
-};
-
-static struct freq_attr* pmac_cpu_freqs_attr[] = {
-	&cpufreq_freq_attr_scaling_available_freqs,
-	NULL,
-};
-
-static inline void local_delay(unsigned long ms)
-{
-	if (no_schedule)
-		mdelay(ms);
-	else
-		msleep(ms);
-}
-
-static inline void wakeup_decrementer(void)
-{
-	set_dec(tb_ticks_per_jiffy);
-	/* No currently-supported powerbook has a 601,
-	 * so use get_tbl, not native
-	 */
-	last_jiffy_stamp(0) = tb_last_stamp = get_tbl();
-}
-
-#ifdef DEBUG_FREQ
-static inline void debug_calc_bogomips(void)
-{
-	/* This will cause a recalc of bogomips and display the
-	 * result. We backup/restore the value to avoid affecting the
-	 * core cpufreq framework's own calculation.
-	 */
-	extern void calibrate_delay(void);
-
-	unsigned long save_lpj = loops_per_jiffy;
-	calibrate_delay();
-	loops_per_jiffy = save_lpj;
-}
-#endif /* DEBUG_FREQ */
-
-/* Switch CPU speed under 750FX CPU control
- */
-static int cpu_750fx_cpu_speed(int low_speed)
-{
-	u32 hid2;
-
-	if (low_speed == 0) {
-		/* ramping up, set voltage first */
-		pmac_call_feature(PMAC_FTR_WRITE_GPIO, NULL, voltage_gpio, 0x05);
-		/* Make sure we sleep for at least 1ms */
-		local_delay(10);
-
-		/* tweak L2 for high voltage */
-		if (has_cpu_l2lve) {
-			hid2 = mfspr(SPRN_HID2);
-			hid2 &= ~0x2000;
-			mtspr(SPRN_HID2, hid2);
-		}
-	}
-#ifdef CONFIG_6xx
-	low_choose_750fx_pll(low_speed);
-#endif
-	if (low_speed == 1) {
-		/* tweak L2 for low voltage */
-		if (has_cpu_l2lve) {
-			hid2 = mfspr(SPRN_HID2);
-			hid2 |= 0x2000;
-			mtspr(SPRN_HID2, hid2);
-		}
-
-		/* ramping down, set voltage last */
-		pmac_call_feature(PMAC_FTR_WRITE_GPIO, NULL, voltage_gpio, 0x04);
-		local_delay(10);
-	}
-
-	return 0;
-}
-
-static unsigned int cpu_750fx_get_cpu_speed(void)
-{
-	if (mfspr(SPRN_HID1) & HID1_PS)
-		return low_freq;
-	else
-		return hi_freq;
-}
-
-/* Switch CPU speed using DFS */
-static int dfs_set_cpu_speed(int low_speed)
-{
-	if (low_speed == 0) {
-		/* ramping up, set voltage first */
-		pmac_call_feature(PMAC_FTR_WRITE_GPIO, NULL, voltage_gpio, 0x05);
-		/* Make sure we sleep for at least 1ms */
-		local_delay(1);
-	}
-
-	/* set frequency */
-#ifdef CONFIG_6xx
-	low_choose_7447a_dfs(low_speed);
-#endif
-	udelay(100);
-
-	if (low_speed == 1) {
-		/* ramping down, set voltage last */
-		pmac_call_feature(PMAC_FTR_WRITE_GPIO, NULL, voltage_gpio, 0x04);
-		local_delay(1);
-	}
-
-	return 0;
-}
-
-static unsigned int dfs_get_cpu_speed(void)
-{
-	if (mfspr(SPRN_HID1) & HID1_DFS)
-		return low_freq;
-	else
-		return hi_freq;
-}
-
-
-/* Switch CPU speed using slewing GPIOs
- */
-static int gpios_set_cpu_speed(int low_speed)
-{
-	int gpio, timeout = 0;
-
-	/* If ramping up, set voltage first */
-	if (low_speed == 0) {
-		pmac_call_feature(PMAC_FTR_WRITE_GPIO, NULL, voltage_gpio, 0x05);
-		/* Delay is way too big but it's ok, we schedule */
-		local_delay(10);
-	}
-
-	/* Set frequency */
-	gpio = 	pmac_call_feature(PMAC_FTR_READ_GPIO, NULL, frequency_gpio, 0);
-	if (low_speed == ((gpio & 0x01) == 0))
-		goto skip;
-
-	pmac_call_feature(PMAC_FTR_WRITE_GPIO, NULL, frequency_gpio,
-			  low_speed ? 0x04 : 0x05);
-	udelay(200);
-	do {
-		if (++timeout > 100)
-			break;
-		local_delay(1);
-		gpio = pmac_call_feature(PMAC_FTR_READ_GPIO, NULL, slew_done_gpio, 0);
-	} while((gpio & 0x02) == 0);
- skip:
-	/* If ramping down, set voltage last */
-	if (low_speed == 1) {
-		pmac_call_feature(PMAC_FTR_WRITE_GPIO, NULL, voltage_gpio, 0x04);
-		/* Delay is way too big but it's ok, we schedule */
-		local_delay(10);
-	}
-
-#ifdef DEBUG_FREQ
-	debug_calc_bogomips();
-#endif
-
-	return 0;
-}
-
-/* Switch CPU speed under PMU control
- */
-static int pmu_set_cpu_speed(int low_speed)
-{
-	struct adb_request req;
-	unsigned long save_l2cr;
-	unsigned long save_l3cr;
-	unsigned int pic_prio;
-	unsigned long flags;
-
-	preempt_disable();
-
-#ifdef DEBUG_FREQ
-	printk(KERN_DEBUG "HID1, before: %x\n", mfspr(SPRN_HID1));
-#endif
-	pmu_suspend();
-
-	/* Disable all interrupt sources on openpic */
- 	pic_prio = openpic_get_priority();
-	openpic_set_priority(0xf);
-
-	/* Make sure the decrementer won't interrupt us */
-	asm volatile("mtdec %0" : : "r" (0x7fffffff));
-	/* Make sure any pending DEC interrupt occuring while we did
-	 * the above didn't re-enable the DEC */
-	mb();
-	asm volatile("mtdec %0" : : "r" (0x7fffffff));
-
-	/* We can now disable MSR_EE */
-	local_irq_save(flags);
-
-	/* Giveup the FPU & vec */
-	enable_kernel_fp();
-
-#ifdef CONFIG_ALTIVEC
-	if (cpu_has_feature(CPU_FTR_ALTIVEC))
-		enable_kernel_altivec();
-#endif /* CONFIG_ALTIVEC */
-
-	/* Save & disable L2 and L3 caches */
-	save_l3cr = _get_L3CR();	/* (returns -1 if not available) */
-	save_l2cr = _get_L2CR();	/* (returns -1 if not available) */
-
-	/* Send the new speed command. My assumption is that this command
-	 * will cause PLL_CFG[0..3] to be changed next time CPU goes to sleep
-	 */
-	pmu_request(&req, NULL, 6, PMU_CPU_SPEED, 'W', 'O', 'O', 'F', low_speed);
-	while (!req.complete)
-		pmu_poll();
-
-	/* Prepare the northbridge for the speed transition */
-	pmac_call_feature(PMAC_FTR_SLEEP_STATE,NULL,1,1);
-
-	/* Call low level code to backup CPU state and recover from
-	 * hardware reset
-	 */
-	low_sleep_handler();
-
-	/* Restore the northbridge */
-	pmac_call_feature(PMAC_FTR_SLEEP_STATE,NULL,1,0);
-
-	/* Restore L2 cache */
-	if (save_l2cr != 0xffffffff && (save_l2cr & L2CR_L2E) != 0)
- 		_set_L2CR(save_l2cr);
-	/* Restore L3 cache */
-	if (save_l3cr != 0xffffffff && (save_l3cr & L3CR_L3E) != 0)
- 		_set_L3CR(save_l3cr);
-
-	/* Restore userland MMU context */
-	set_context(current->active_mm->context, current->active_mm->pgd);
-
-#ifdef DEBUG_FREQ
-	printk(KERN_DEBUG "HID1, after: %x\n", mfspr(SPRN_HID1));
-#endif
-
-	/* Restore low level PMU operations */
-	pmu_unlock();
-
-	/* Restore decrementer */
-	wakeup_decrementer();
-
-	/* Restore interrupts */
- 	openpic_set_priority(pic_prio);
-
-	/* Let interrupts flow again ... */
-	local_irq_restore(flags);
-
-#ifdef DEBUG_FREQ
-	debug_calc_bogomips();
-#endif
-
-	pmu_resume();
-
-	preempt_enable();
-
-	return 0;
-}
-
-static int do_set_cpu_speed(int speed_mode, int notify)
-{
-	struct cpufreq_freqs freqs;
-	unsigned long l3cr;
-	static unsigned long prev_l3cr;
-
-	freqs.old = cur_freq;
-	freqs.new = (speed_mode == CPUFREQ_HIGH) ? hi_freq : low_freq;
-	freqs.cpu = smp_processor_id();
-
-	if (freqs.old == freqs.new)
-		return 0;
-
-	if (notify)
-		cpufreq_notify_transition(&freqs, CPUFREQ_PRECHANGE);
-	if (speed_mode == CPUFREQ_LOW &&
-	    cpu_has_feature(CPU_FTR_L3CR)) {
-		l3cr = _get_L3CR();
-		if (l3cr & L3CR_L3E) {
-			prev_l3cr = l3cr;
-			_set_L3CR(0);
-		}
-	}
-	set_speed_proc(speed_mode == CPUFREQ_LOW);
-	if (speed_mode == CPUFREQ_HIGH &&
-	    cpu_has_feature(CPU_FTR_L3CR)) {
-		l3cr = _get_L3CR();
-		if ((prev_l3cr & L3CR_L3E) && l3cr != prev_l3cr)
-			_set_L3CR(prev_l3cr);
-	}
-	if (notify)
-		cpufreq_notify_transition(&freqs, CPUFREQ_POSTCHANGE);
-	cur_freq = (speed_mode == CPUFREQ_HIGH) ? hi_freq : low_freq;
-
-	return 0;
-}
-
-static unsigned int pmac_cpufreq_get_speed(unsigned int cpu)
-{
-	return cur_freq;
-}
-
-static int pmac_cpufreq_verify(struct cpufreq_policy *policy)
-{
-	return cpufreq_frequency_table_verify(policy, pmac_cpu_freqs);
-}
-
-static int pmac_cpufreq_target(	struct cpufreq_policy *policy,
-					unsigned int target_freq,
-					unsigned int relation)
-{
-	unsigned int    newstate = 0;
-
-	if (cpufreq_frequency_table_target(policy, pmac_cpu_freqs,
-			target_freq, relation, &newstate))
-		return -EINVAL;
-
-	return do_set_cpu_speed(newstate, 1);
-}
-
-unsigned int pmac_get_one_cpufreq(int i)
-{
-	/* Supports only one CPU for now */
-	return (i == 0) ? cur_freq : 0;
-}
-
-static int pmac_cpufreq_cpu_init(struct cpufreq_policy *policy)
-{
-	if (policy->cpu != 0)
-		return -ENODEV;
-
-	policy->governor = CPUFREQ_DEFAULT_GOVERNOR;
-	policy->cpuinfo.transition_latency	= CPUFREQ_ETERNAL;
-	policy->cur = cur_freq;
-
-	cpufreq_frequency_table_get_attr(pmac_cpu_freqs, policy->cpu);
-	return cpufreq_frequency_table_cpuinfo(policy, pmac_cpu_freqs);
-}
-
-static u32 read_gpio(struct device_node *np)
-{
-	u32 *reg = (u32 *)get_property(np, "reg", NULL);
-	u32 offset;
-
-	if (reg == NULL)
-		return 0;
-	/* That works for all keylargos but shall be fixed properly
-	 * some day... The problem is that it seems we can't rely
-	 * on the "reg" property of the GPIO nodes, they are either
-	 * relative to the base of KeyLargo or to the base of the
-	 * GPIO space, and the device-tree doesn't help.
-	 */
-	offset = *reg;
-	if (offset < KEYLARGO_GPIO_LEVELS0)
-		offset += KEYLARGO_GPIO_LEVELS0;
-	return offset;
-}
-
-static int pmac_cpufreq_suspend(struct cpufreq_policy *policy, pm_message_t pmsg)
-{
-	/* Ok, this could be made a bit smarter, but let's be robust for now. We
-	 * always force a speed change to high speed before sleep, to make sure
-	 * we have appropriate voltage and/or bus speed for the wakeup process,
-	 * and to make sure our loops_per_jiffies are "good enough", that is will
-	 * not cause too short delays if we sleep in low speed and wake in high
-	 * speed..
-	 */
-	no_schedule = 1;
-	sleep_freq = cur_freq;
-	if (cur_freq == low_freq && !is_pmu_based)
-		do_set_cpu_speed(CPUFREQ_HIGH, 0);
-	return 0;
-}
-
-static int pmac_cpufreq_resume(struct cpufreq_policy *policy)
-{
-	/* If we resume, first check if we have a get() function */
-	if (get_speed_proc)
-		cur_freq = get_speed_proc();
-	else
-		cur_freq = 0;
-
-	/* We don't, hrm... we don't really know our speed here, best
-	 * is that we force a switch to whatever it was, which is
-	 * probably high speed due to our suspend() routine
-	 */
-	do_set_cpu_speed(sleep_freq == low_freq ?
-			 CPUFREQ_LOW : CPUFREQ_HIGH, 0);
-
-	no_schedule = 0;
-	return 0;
-}
-
-static struct cpufreq_driver pmac_cpufreq_driver = {
-	.verify 	= pmac_cpufreq_verify,
-	.target 	= pmac_cpufreq_target,
-	.get		= pmac_cpufreq_get_speed,
-	.init		= pmac_cpufreq_cpu_init,
-	.suspend	= pmac_cpufreq_suspend,
-	.resume		= pmac_cpufreq_resume,
-	.flags		= CPUFREQ_PM_NO_WARN,
-	.attr		= pmac_cpu_freqs_attr,
-	.name		= "powermac",
-	.owner		= THIS_MODULE,
-};
-
-
-static int pmac_cpufreq_init_MacRISC3(struct device_node *cpunode)
-{
-	struct device_node *volt_gpio_np = of_find_node_by_name(NULL,
-								"voltage-gpio");
-	struct device_node *freq_gpio_np = of_find_node_by_name(NULL,
-								"frequency-gpio");
-	struct device_node *slew_done_gpio_np = of_find_node_by_name(NULL,
-								     "slewing-done");
-	u32 *value;
-
-	/*
-	 * Check to see if it's GPIO driven or PMU only
-	 *
-	 * The way we extract the GPIO address is slightly hackish, but it
-	 * works well enough for now. We need to abstract the whole GPIO
-	 * stuff sooner or later anyway
-	 */
-
-	if (volt_gpio_np)
-		voltage_gpio = read_gpio(volt_gpio_np);
-	if (freq_gpio_np)
-		frequency_gpio = read_gpio(freq_gpio_np);
-	if (slew_done_gpio_np)
-		slew_done_gpio = read_gpio(slew_done_gpio_np);
-
-	/* If we use the frequency GPIOs, calculate the min/max speeds based
-	 * on the bus frequencies
-	 */
-	if (frequency_gpio && slew_done_gpio) {
-		int lenp, rc;
-		u32 *freqs, *ratio;
-
-		freqs = (u32 *)get_property(cpunode, "bus-frequencies", &lenp);
-		lenp /= sizeof(u32);
-		if (freqs == NULL || lenp != 2) {
-			printk(KERN_ERR "cpufreq: bus-frequencies incorrect or missing\n");
-			return 1;
-		}
-		ratio = (u32 *)get_property(cpunode, "processor-to-bus-ratio*2", NULL);
-		if (ratio == NULL) {
-			printk(KERN_ERR "cpufreq: processor-to-bus-ratio*2 missing\n");
-			return 1;
-		}
-
-		/* Get the min/max bus frequencies */
-		low_freq = min(freqs[0], freqs[1]);
-		hi_freq = max(freqs[0], freqs[1]);
-
-		/* Grrrr.. It _seems_ that the device-tree is lying on the low bus
-		 * frequency, it claims it to be around 84Mhz on some models while
-		 * it appears to be approx. 101Mhz on all. Let's hack around here...
-		 * fortunately, we don't need to be too precise
-		 */
-		if (low_freq < 98000000)
-			low_freq = 101000000;
-			
-		/* Convert those to CPU core clocks */
-		low_freq = (low_freq * (*ratio)) / 2000;
-		hi_freq = (hi_freq * (*ratio)) / 2000;
-
-		/* Now we get the frequencies, we read the GPIO to see what is out current
-		 * speed
-		 */
-		rc = pmac_call_feature(PMAC_FTR_READ_GPIO, NULL, frequency_gpio, 0);
-		cur_freq = (rc & 0x01) ? hi_freq : low_freq;
-
-		set_speed_proc = gpios_set_cpu_speed;
-		return 1;
-	}
-
-	/* If we use the PMU, look for the min & max frequencies in the
-	 * device-tree
-	 */
-	value = (u32 *)get_property(cpunode, "min-clock-frequency", NULL);
-	if (!value)
-		return 1;
-	low_freq = (*value) / 1000;
-	/* The PowerBook G4 12" (PowerBook6,1) has an error in the device-tree
-	 * here */
-	if (low_freq < 100000)
-		low_freq *= 10;
-
-	value = (u32 *)get_property(cpunode, "max-clock-frequency", NULL);
-	if (!value)
-		return 1;
-	hi_freq = (*value) / 1000;
-	set_speed_proc = pmu_set_cpu_speed;
-	is_pmu_based = 1;
-
-	return 0;
-}
-
-static int pmac_cpufreq_init_7447A(struct device_node *cpunode)
-{
-	struct device_node *volt_gpio_np;
-
-	if (get_property(cpunode, "dynamic-power-step", NULL) == NULL)
-		return 1;
-
-	volt_gpio_np = of_find_node_by_name(NULL, "cpu-vcore-select");
-	if (volt_gpio_np)
-		voltage_gpio = read_gpio(volt_gpio_np);
-	if (!voltage_gpio){
-		printk(KERN_ERR "cpufreq: missing cpu-vcore-select gpio\n");
-		return 1;
-	}
-
-	/* OF only reports the high frequency */
-	hi_freq = cur_freq;
-	low_freq = cur_freq/2;
-
-	/* Read actual frequency from CPU */
-	cur_freq = dfs_get_cpu_speed();
-	set_speed_proc = dfs_set_cpu_speed;
-	get_speed_proc = dfs_get_cpu_speed;
-
-	return 0;
-}
-
-static int pmac_cpufreq_init_750FX(struct device_node *cpunode)
-{
-	struct device_node *volt_gpio_np;
-	u32 pvr, *value;
-
-	if (get_property(cpunode, "dynamic-power-step", NULL) == NULL)
-		return 1;
-
-	hi_freq = cur_freq;
-	value = (u32 *)get_property(cpunode, "reduced-clock-frequency", NULL);
-	if (!value)
-		return 1;
-	low_freq = (*value) / 1000;
-
-	volt_gpio_np = of_find_node_by_name(NULL, "cpu-vcore-select");
-	if (volt_gpio_np)
-		voltage_gpio = read_gpio(volt_gpio_np);
-
-	pvr = mfspr(SPRN_PVR);
-	has_cpu_l2lve = !((pvr & 0xf00) == 0x100);
-
-	set_speed_proc = cpu_750fx_cpu_speed;
-	get_speed_proc = cpu_750fx_get_cpu_speed;
-	cur_freq = cpu_750fx_get_cpu_speed();
-
-	return 0;
-}
-
-/* Currently, we support the following machines:
- *
- *  - Titanium PowerBook 1Ghz (PMU based, 667Mhz & 1Ghz)
- *  - Titanium PowerBook 800 (PMU based, 667Mhz & 800Mhz)
- *  - Titanium PowerBook 400 (PMU based, 300Mhz & 400Mhz)
- *  - Titanium PowerBook 500 (PMU based, 300Mhz & 500Mhz)
- *  - iBook2 500/600 (PMU based, 400Mhz & 500/600Mhz)
- *  - iBook2 700 (CPU based, 400Mhz & 700Mhz, support low voltage)
- *  - Recent MacRISC3 laptops
- *  - All new machines with 7447A CPUs
- */
-static int __init pmac_cpufreq_setup(void)
-{
-	struct device_node	*cpunode;
-	u32			*value;
-
-	if (strstr(cmd_line, "nocpufreq"))
-		return 0;
-
-	/* Assume only one CPU */
-	cpunode = find_type_devices("cpu");
-	if (!cpunode)
-		goto out;
-
-	/* Get current cpu clock freq */
-	value = (u32 *)get_property(cpunode, "clock-frequency", NULL);
-	if (!value)
-		goto out;
-	cur_freq = (*value) / 1000;
-
-	/*  Check for 7447A based MacRISC3 */
-	if (machine_is_compatible("MacRISC3") &&
-	    get_property(cpunode, "dynamic-power-step", NULL) &&
-	    PVR_VER(mfspr(SPRN_PVR)) == 0x8003) {
-		pmac_cpufreq_init_7447A(cpunode);
-	/* Check for other MacRISC3 machines */
-	} else if (machine_is_compatible("PowerBook3,4") ||
-		   machine_is_compatible("PowerBook3,5") ||
-		   machine_is_compatible("MacRISC3")) {
-		pmac_cpufreq_init_MacRISC3(cpunode);
-	/* Else check for iBook2 500/600 */
-	} else if (machine_is_compatible("PowerBook4,1")) {
-		hi_freq = cur_freq;
-		low_freq = 400000;
-		set_speed_proc = pmu_set_cpu_speed;
-		is_pmu_based = 1;
-	}
-	/* Else check for TiPb 550 */
-	else if (machine_is_compatible("PowerBook3,3") && cur_freq == 550000) {
-		hi_freq = cur_freq;
-		low_freq = 500000;
-		set_speed_proc = pmu_set_cpu_speed;
-		is_pmu_based = 1;
-	}
-	/* Else check for TiPb 400 & 500 */
-	else if (machine_is_compatible("PowerBook3,2")) {
-		/* We only know about the 400 MHz and the 500Mhz model
-		 * they both have 300 MHz as low frequency
-		 */
-		if (cur_freq < 350000 || cur_freq > 550000)
-			goto out;
-		hi_freq = cur_freq;
-		low_freq = 300000;
-		set_speed_proc = pmu_set_cpu_speed;
-		is_pmu_based = 1;
-	}
-	/* Else check for 750FX */
-	else if (PVR_VER(mfspr(SPRN_PVR)) == 0x7000)
-		pmac_cpufreq_init_750FX(cpunode);
-out:
-	if (set_speed_proc == NULL)
-		return -ENODEV;
-
-	pmac_cpu_freqs[CPUFREQ_LOW].frequency = low_freq;
-	pmac_cpu_freqs[CPUFREQ_HIGH].frequency = hi_freq;
-
-	printk(KERN_INFO "Registering PowerMac CPU frequency driver\n");
-	printk(KERN_INFO "Low: %d Mhz, High: %d Mhz, Boot: %d Mhz\n",
-	       low_freq/1000, hi_freq/1000, cur_freq/1000);
-
-	return cpufreq_register_driver(&pmac_cpufreq_driver);
-}
-
-module_init(pmac_cpufreq_setup);
-
diff --git a/arch/ppc/platforms/pmac_feature.c b/arch/ppc/platforms/pmac_feature.c
deleted file mode 100644
index 6b7b3a15063..00000000000
--- a/arch/ppc/platforms/pmac_feature.c
+++ /dev/null
@@ -1,3023 +0,0 @@
-/*
- *  arch/ppc/platforms/pmac_feature.c
- *
- *  Copyright (C) 1996-2001 Paul Mackerras (paulus@cs.anu.edu.au)
- *                          Ben. Herrenschmidt (benh@kernel.crashing.org)
- *
- *  This program is free software; you can redistribute it and/or
- *  modify it under the terms of the GNU General Public License
- *  as published by the Free Software Foundation; either version
- *  2 of the License, or (at your option) any later version.
- *
- *  TODO:
- *
- *   - Replace mdelay with some schedule loop if possible
- *   - Shorten some obfuscated delays on some routines (like modem
- *     power)
- *   - Refcount some clocks (see darwin)
- *   - Split split split...
- *
- */
-#include <linux/config.h>
-#include <linux/types.h>
-#include <linux/init.h>
-#include <linux/delay.h>
-#include <linux/kernel.h>
-#include <linux/sched.h>
-#include <linux/spinlock.h>
-#include <linux/adb.h>
-#include <linux/pmu.h>
-#include <linux/ioport.h>
-#include <linux/pci.h>
-#include <asm/sections.h>
-#include <asm/errno.h>
-#include <asm/ohare.h>
-#include <asm/heathrow.h>
-#include <asm/keylargo.h>
-#include <asm/uninorth.h>
-#include <asm/io.h>
-#include <asm/prom.h>
-#include <asm/machdep.h>
-#include <asm/pmac_feature.h>
-#include <asm/dbdma.h>
-#include <asm/pci-bridge.h>
-#include <asm/pmac_low_i2c.h>
-
-#undef DEBUG_FEATURE
-
-#ifdef DEBUG_FEATURE
-#define DBG(fmt,...) printk(KERN_DEBUG fmt)
-#else
-#define DBG(fmt,...)
-#endif
-
-#ifdef CONFIG_6xx
-extern int powersave_lowspeed;
-#endif
-
-extern int powersave_nap;
-extern struct device_node *k2_skiplist[2];
-
-
-/*
- * We use a single global lock to protect accesses. Each driver has
- * to take care of its own locking
- */
-static DEFINE_SPINLOCK(feature_lock);
-
-#define LOCK(flags)	spin_lock_irqsave(&feature_lock, flags);
-#define UNLOCK(flags)	spin_unlock_irqrestore(&feature_lock, flags);
-
-
-/*
- * Instance of some macio stuffs
- */
-struct macio_chip macio_chips[MAX_MACIO_CHIPS];
-
-struct macio_chip* macio_find(struct device_node* child, int type)
-{
-	while(child) {
-		int	i;
-
-		for (i=0; i < MAX_MACIO_CHIPS && macio_chips[i].of_node; i++)
-			if (child == macio_chips[i].of_node &&
-			    (!type || macio_chips[i].type == type))
-				return &macio_chips[i];
-		child = child->parent;
-	}
-	return NULL;
-}
-EXPORT_SYMBOL_GPL(macio_find);
-
-static const char* macio_names[] =
-{
-	"Unknown",
-	"Grand Central",
-	"OHare",
-	"OHareII",
-	"Heathrow",
-	"Gatwick",
-	"Paddington",
-	"Keylargo",
-	"Pangea",
-	"Intrepid",
-	"K2"
-};
-
-
-
-/*
- * Uninorth reg. access. Note that Uni-N regs are big endian
- */
-
-#define UN_REG(r)	(uninorth_base + ((r) >> 2))
-#define UN_IN(r)	(in_be32(UN_REG(r)))
-#define UN_OUT(r,v)	(out_be32(UN_REG(r), (v)))
-#define UN_BIS(r,v)	(UN_OUT((r), UN_IN(r) | (v)))
-#define UN_BIC(r,v)	(UN_OUT((r), UN_IN(r) & ~(v)))
-
-static struct device_node* uninorth_node;
-static u32 __iomem * uninorth_base;
-static u32 uninorth_rev;
-static int uninorth_u3;
-static void __iomem *u3_ht;
-
-/*
- * For each motherboard family, we have a table of functions pointers
- * that handle the various features.
- */
-
-typedef long (*feature_call)(struct device_node* node, long param, long value);
-
-struct feature_table_entry {
-	unsigned int	selector;
-	feature_call	function;
-};
-
-struct pmac_mb_def
-{
-	const char*			model_string;
-	const char*			model_name;
-	int				model_id;
-	struct feature_table_entry* 	features;
-	unsigned long			board_flags;
-};
-static struct pmac_mb_def pmac_mb;
-
-/*
- * Here are the chip specific feature functions
- */
-
-static inline int
-simple_feature_tweak(struct device_node* node, int type, int reg, u32 mask, int value)
-{
-	struct macio_chip*	macio;
-	unsigned long		flags;
-
-	macio = macio_find(node, type);
-	if (!macio)
-		return -ENODEV;
-	LOCK(flags);
-	if (value)
-		MACIO_BIS(reg, mask);
-	else
-		MACIO_BIC(reg, mask);
-	(void)MACIO_IN32(reg);
-	UNLOCK(flags);
-
-	return 0;
-}
-
-#ifndef CONFIG_POWER4
-
-static long
-ohare_htw_scc_enable(struct device_node* node, long param, long value)
-{
-	struct macio_chip*	macio;
-	unsigned long		chan_mask;
-	unsigned long		fcr;
-	unsigned long		flags;
-	int			htw, trans;
-	unsigned long		rmask;
-
-	macio = macio_find(node, 0);
-	if (!macio)
-		return -ENODEV;
-	if (!strcmp(node->name, "ch-a"))
-		chan_mask = MACIO_FLAG_SCCA_ON;
-	else if (!strcmp(node->name, "ch-b"))
-		chan_mask = MACIO_FLAG_SCCB_ON;
-	else
-		return -ENODEV;
-
-	htw = (macio->type == macio_heathrow || macio->type == macio_paddington
-		|| macio->type == macio_gatwick);
-	/* On these machines, the HRW_SCC_TRANS_EN_N bit mustn't be touched */
-	trans = (pmac_mb.model_id != PMAC_TYPE_YOSEMITE &&
-	    	 pmac_mb.model_id != PMAC_TYPE_YIKES);
-	if (value) {
-#ifdef CONFIG_ADB_PMU
-		if ((param & 0xfff) == PMAC_SCC_IRDA)
-			pmu_enable_irled(1);
-#endif /* CONFIG_ADB_PMU */
-		LOCK(flags);
-		fcr = MACIO_IN32(OHARE_FCR);
-		/* Check if scc cell need enabling */
-		if (!(fcr & OH_SCC_ENABLE)) {
-			fcr |= OH_SCC_ENABLE;
-			if (htw) {
-				/* Side effect: this will also power up the
-				 * modem, but it's too messy to figure out on which
-				 * ports this controls the tranceiver and on which
-				 * it controls the modem
-				 */
-				if (trans)
-					fcr &= ~HRW_SCC_TRANS_EN_N;
-				MACIO_OUT32(OHARE_FCR, fcr);
-				fcr |= (rmask = HRW_RESET_SCC);
-				MACIO_OUT32(OHARE_FCR, fcr);
-			} else {
-				fcr |= (rmask = OH_SCC_RESET);
-				MACIO_OUT32(OHARE_FCR, fcr);
-			}
-			UNLOCK(flags);
-			(void)MACIO_IN32(OHARE_FCR);
-			mdelay(15);
-			LOCK(flags);
-			fcr &= ~rmask;
-			MACIO_OUT32(OHARE_FCR, fcr);
-		}
-		if (chan_mask & MACIO_FLAG_SCCA_ON)
-			fcr |= OH_SCCA_IO;
-		if (chan_mask & MACIO_FLAG_SCCB_ON)
-			fcr |= OH_SCCB_IO;
-		MACIO_OUT32(OHARE_FCR, fcr);
-		macio->flags |= chan_mask;
-		UNLOCK(flags);
-		if (param & PMAC_SCC_FLAG_XMON)
-			macio->flags |= MACIO_FLAG_SCC_LOCKED;
-	} else {
-		if (macio->flags & MACIO_FLAG_SCC_LOCKED)
-			return -EPERM;
-		LOCK(flags);
-		fcr = MACIO_IN32(OHARE_FCR);
-		if (chan_mask & MACIO_FLAG_SCCA_ON)
-			fcr &= ~OH_SCCA_IO;
-		if (chan_mask & MACIO_FLAG_SCCB_ON)
-			fcr &= ~OH_SCCB_IO;
-		MACIO_OUT32(OHARE_FCR, fcr);
-		if ((fcr & (OH_SCCA_IO | OH_SCCB_IO)) == 0) {
-			fcr &= ~OH_SCC_ENABLE;
-			if (htw && trans)
-				fcr |= HRW_SCC_TRANS_EN_N;
-			MACIO_OUT32(OHARE_FCR, fcr);
-		}
-		macio->flags &= ~(chan_mask);
-		UNLOCK(flags);
-		mdelay(10);
-#ifdef CONFIG_ADB_PMU
-		if ((param & 0xfff) == PMAC_SCC_IRDA)
-			pmu_enable_irled(0);
-#endif /* CONFIG_ADB_PMU */
-	}
-	return 0;
-}
-
-static long
-ohare_floppy_enable(struct device_node* node, long param, long value)
-{
-	return simple_feature_tweak(node, macio_ohare,
-		OHARE_FCR, OH_FLOPPY_ENABLE, value);
-}
-
-static long
-ohare_mesh_enable(struct device_node* node, long param, long value)
-{
-	return simple_feature_tweak(node, macio_ohare,
-		OHARE_FCR, OH_MESH_ENABLE, value);
-}
-
-static long
-ohare_ide_enable(struct device_node* node, long param, long value)
-{
-	switch(param) {
-	    case 0:
-	    	/* For some reason, setting the bit in set_initial_features()
-	    	 * doesn't stick. I'm still investigating... --BenH.
-	    	 */
-	    	if (value)
-	    		simple_feature_tweak(node, macio_ohare,
-				OHARE_FCR, OH_IOBUS_ENABLE, 1);
-		return simple_feature_tweak(node, macio_ohare,
-			OHARE_FCR, OH_IDE0_ENABLE, value);
-	    case 1:
-		return simple_feature_tweak(node, macio_ohare,
-			OHARE_FCR, OH_BAY_IDE_ENABLE, value);
-	    default:
-	    	return -ENODEV;
-	}
-}
-
-static long
-ohare_ide_reset(struct device_node* node, long param, long value)
-{
-	switch(param) {
-	    case 0:
-		return simple_feature_tweak(node, macio_ohare,
-			OHARE_FCR, OH_IDE0_RESET_N, !value);
-	    case 1:
-		return simple_feature_tweak(node, macio_ohare,
-			OHARE_FCR, OH_IDE1_RESET_N, !value);
-	    default:
-	    	return -ENODEV;
-	}
-}
-
-static long
-ohare_sleep_state(struct device_node* node, long param, long value)
-{
-	struct macio_chip*	macio = &macio_chips[0];
-
-	if ((pmac_mb.board_flags & PMAC_MB_CAN_SLEEP) == 0)
-		return -EPERM;
-	if (value == 1) {
-		MACIO_BIC(OHARE_FCR, OH_IOBUS_ENABLE);
-	} else if (value == 0) {
-		MACIO_BIS(OHARE_FCR, OH_IOBUS_ENABLE);
-	}
-
-	return 0;
-}
-
-static long
-heathrow_modem_enable(struct device_node* node, long param, long value)
-{
-	struct macio_chip*	macio;
-	u8			gpio;
-	unsigned long		flags;
-
-	macio = macio_find(node, macio_unknown);
-	if (!macio)
-		return -ENODEV;
-	gpio = MACIO_IN8(HRW_GPIO_MODEM_RESET) & ~1;
-	if (!value) {
-		LOCK(flags);
-		MACIO_OUT8(HRW_GPIO_MODEM_RESET, gpio);
-		UNLOCK(flags);
-		(void)MACIO_IN8(HRW_GPIO_MODEM_RESET);
-		mdelay(250);
-	}
-	if (pmac_mb.model_id != PMAC_TYPE_YOSEMITE &&
-	    pmac_mb.model_id != PMAC_TYPE_YIKES) {
-	    	LOCK(flags);
-	    	if (value)
-	    		MACIO_BIC(HEATHROW_FCR, HRW_SCC_TRANS_EN_N);
-	    	else
-	    		MACIO_BIS(HEATHROW_FCR, HRW_SCC_TRANS_EN_N);
-	    	UNLOCK(flags);
-	    	(void)MACIO_IN32(HEATHROW_FCR);
-		mdelay(250);
-	}
-	if (value) {
-		LOCK(flags);
-		MACIO_OUT8(HRW_GPIO_MODEM_RESET, gpio | 1);
-		(void)MACIO_IN8(HRW_GPIO_MODEM_RESET);
-	    	UNLOCK(flags); mdelay(250); LOCK(flags);
-		MACIO_OUT8(HRW_GPIO_MODEM_RESET, gpio);
-		(void)MACIO_IN8(HRW_GPIO_MODEM_RESET);
-	    	UNLOCK(flags); mdelay(250); LOCK(flags);
-		MACIO_OUT8(HRW_GPIO_MODEM_RESET, gpio | 1);
-		(void)MACIO_IN8(HRW_GPIO_MODEM_RESET);
-	    	UNLOCK(flags); mdelay(250);
-	}
-	return 0;
-}
-
-static long
-heathrow_floppy_enable(struct device_node* node, long param, long value)
-{
-	return simple_feature_tweak(node, macio_unknown,
-		HEATHROW_FCR,
-		HRW_SWIM_ENABLE|HRW_BAY_FLOPPY_ENABLE,
-		value);
-}
-
-static long
-heathrow_mesh_enable(struct device_node* node, long param, long value)
-{
-	struct macio_chip*	macio;
-	unsigned long		flags;
-
-	macio = macio_find(node, macio_unknown);
-	if (!macio)
-		return -ENODEV;
-	LOCK(flags);
-	/* Set clear mesh cell enable */
-	if (value)
-		MACIO_BIS(HEATHROW_FCR, HRW_MESH_ENABLE);
-	else
-		MACIO_BIC(HEATHROW_FCR, HRW_MESH_ENABLE);
-	(void)MACIO_IN32(HEATHROW_FCR);
-	udelay(10);
-	/* Set/Clear termination power */
-	if (value)
-		MACIO_BIC(HEATHROW_MBCR, 0x04000000);
-	else
-		MACIO_BIS(HEATHROW_MBCR, 0x04000000);
-	(void)MACIO_IN32(HEATHROW_MBCR);
-	udelay(10);
-	UNLOCK(flags);
-
-	return 0;
-}
-
-static long
-heathrow_ide_enable(struct device_node* node, long param, long value)
-{
-	switch(param) {
-	    case 0:
-		return simple_feature_tweak(node, macio_unknown,
-			HEATHROW_FCR, HRW_IDE0_ENABLE, value);
-	    case 1:
-		return simple_feature_tweak(node, macio_unknown,
-			HEATHROW_FCR, HRW_BAY_IDE_ENABLE, value);
-	    default:
-	    	return -ENODEV;
-	}
-}
-
-static long
-heathrow_ide_reset(struct device_node* node, long param, long value)
-{
-	switch(param) {
-	    case 0:
-		return simple_feature_tweak(node, macio_unknown,
-			HEATHROW_FCR, HRW_IDE0_RESET_N, !value);
-	    case 1:
-		return simple_feature_tweak(node, macio_unknown,
-			HEATHROW_FCR, HRW_IDE1_RESET_N, !value);
-	    default:
-	    	return -ENODEV;
-	}
-}
-
-static long
-heathrow_bmac_enable(struct device_node* node, long param, long value)
-{
-	struct macio_chip*	macio;
-	unsigned long		flags;
-
-	macio = macio_find(node, 0);
-	if (!macio)
-		return -ENODEV;
-	if (value) {
-		LOCK(flags);
-		MACIO_BIS(HEATHROW_FCR, HRW_BMAC_IO_ENABLE);
-		MACIO_BIS(HEATHROW_FCR, HRW_BMAC_RESET);
-		UNLOCK(flags);
-		(void)MACIO_IN32(HEATHROW_FCR);
-		mdelay(10);
-		LOCK(flags);
-		MACIO_BIC(HEATHROW_FCR, HRW_BMAC_RESET);
-		UNLOCK(flags);
-		(void)MACIO_IN32(HEATHROW_FCR);
-		mdelay(10);
-	} else {
-		LOCK(flags);
-		MACIO_BIC(HEATHROW_FCR, HRW_BMAC_IO_ENABLE);
-		UNLOCK(flags);
-	}
-	return 0;
-}
-
-static long
-heathrow_sound_enable(struct device_node* node, long param, long value)
-{
-	struct macio_chip*	macio;
-	unsigned long		flags;
-
-	/* B&W G3 and Yikes don't support that properly (the
-	 * sound appear to never come back after beeing shut down).
-	 */
-	if (pmac_mb.model_id == PMAC_TYPE_YOSEMITE ||
-	    pmac_mb.model_id == PMAC_TYPE_YIKES)
-		return 0;
-
-	macio = macio_find(node, 0);
-	if (!macio)
-		return -ENODEV;
-	if (value) {
-		LOCK(flags);
-		MACIO_BIS(HEATHROW_FCR, HRW_SOUND_CLK_ENABLE);
-		MACIO_BIC(HEATHROW_FCR, HRW_SOUND_POWER_N);
-		UNLOCK(flags);
-		(void)MACIO_IN32(HEATHROW_FCR);
-	} else {
-		LOCK(flags);
-		MACIO_BIS(HEATHROW_FCR, HRW_SOUND_POWER_N);
-		MACIO_BIC(HEATHROW_FCR, HRW_SOUND_CLK_ENABLE);
-		UNLOCK(flags);
-	}
-	return 0;
-}
-
-static u32 save_fcr[6];
-static u32 save_mbcr;
-static u32 save_gpio_levels[2];
-static u8 save_gpio_extint[KEYLARGO_GPIO_EXTINT_CNT];
-static u8 save_gpio_normal[KEYLARGO_GPIO_CNT];
-static u32 save_unin_clock_ctl;
-static struct dbdma_regs save_dbdma[13];
-static struct dbdma_regs save_alt_dbdma[13];
-
-static void
-dbdma_save(struct macio_chip* macio, struct dbdma_regs* save)
-{
-	int i;
-
-	/* Save state & config of DBDMA channels */
-	for (i=0; i<13; i++) {
-		volatile struct dbdma_regs __iomem * chan = (void __iomem *)
-			(macio->base + ((0x8000+i*0x100)>>2));
-		save[i].cmdptr_hi = in_le32(&chan->cmdptr_hi);
-		save[i].cmdptr = in_le32(&chan->cmdptr);
-		save[i].intr_sel = in_le32(&chan->intr_sel);
-		save[i].br_sel = in_le32(&chan->br_sel);
-		save[i].wait_sel = in_le32(&chan->wait_sel);
-	}
-}
-
-static void
-dbdma_restore(struct macio_chip* macio, struct dbdma_regs* save)
-{
-	int i;
-
-	/* Save state & config of DBDMA channels */
-	for (i=0; i<13; i++) {
-		volatile struct dbdma_regs __iomem * chan = (void __iomem *)
-			(macio->base + ((0x8000+i*0x100)>>2));
-		out_le32(&chan->control, (ACTIVE|DEAD|WAKE|FLUSH|PAUSE|RUN)<<16);
-		while (in_le32(&chan->status) & ACTIVE)
-			mb();
-		out_le32(&chan->cmdptr_hi, save[i].cmdptr_hi);
-		out_le32(&chan->cmdptr, save[i].cmdptr);
-		out_le32(&chan->intr_sel, save[i].intr_sel);
-		out_le32(&chan->br_sel, save[i].br_sel);
-		out_le32(&chan->wait_sel, save[i].wait_sel);
-	}
-}
-
-static void
-heathrow_sleep(struct macio_chip* macio, int secondary)
-{
-	if (secondary) {
-		dbdma_save(macio, save_alt_dbdma);
-		save_fcr[2] = MACIO_IN32(0x38);
-		save_fcr[3] = MACIO_IN32(0x3c);
-	} else {
-		dbdma_save(macio, save_dbdma);
-		save_fcr[0] = MACIO_IN32(0x38);
-		save_fcr[1] = MACIO_IN32(0x3c);
-		save_mbcr = MACIO_IN32(0x34);
-		/* Make sure sound is shut down */
-		MACIO_BIS(HEATHROW_FCR, HRW_SOUND_POWER_N);
-		MACIO_BIC(HEATHROW_FCR, HRW_SOUND_CLK_ENABLE);
-		/* This seems to be necessary as well or the fan
-		 * keeps coming up and battery drains fast */
-		MACIO_BIC(HEATHROW_FCR, HRW_IOBUS_ENABLE);
-		MACIO_BIC(HEATHROW_FCR, HRW_IDE0_RESET_N);
-		/* Make sure eth is down even if module or sleep
-		 * won't work properly */
-		MACIO_BIC(HEATHROW_FCR, HRW_BMAC_IO_ENABLE | HRW_BMAC_RESET);
-	}
-	/* Make sure modem is shut down */
-	MACIO_OUT8(HRW_GPIO_MODEM_RESET,
-		MACIO_IN8(HRW_GPIO_MODEM_RESET) & ~1);
-	MACIO_BIS(HEATHROW_FCR, HRW_SCC_TRANS_EN_N);
-	MACIO_BIC(HEATHROW_FCR, OH_SCCA_IO|OH_SCCB_IO|HRW_SCC_ENABLE);
-
-	/* Let things settle */
-	(void)MACIO_IN32(HEATHROW_FCR);
-}
-
-static void
-heathrow_wakeup(struct macio_chip* macio, int secondary)
-{
-	if (secondary) {
-		MACIO_OUT32(0x38, save_fcr[2]);
-		(void)MACIO_IN32(0x38);
-		mdelay(1);
-		MACIO_OUT32(0x3c, save_fcr[3]);
-		(void)MACIO_IN32(0x38);
-		mdelay(10);
-		dbdma_restore(macio, save_alt_dbdma);
-	} else {
-		MACIO_OUT32(0x38, save_fcr[0] | HRW_IOBUS_ENABLE);
-		(void)MACIO_IN32(0x38);
-		mdelay(1);
-		MACIO_OUT32(0x3c, save_fcr[1]);
-		(void)MACIO_IN32(0x38);
-		mdelay(1);
-		MACIO_OUT32(0x34, save_mbcr);
-		(void)MACIO_IN32(0x38);
-		mdelay(10);
-		dbdma_restore(macio, save_dbdma);
-	}
-}
-
-static long
-heathrow_sleep_state(struct device_node* node, long param, long value)
-{
-	if ((pmac_mb.board_flags & PMAC_MB_CAN_SLEEP) == 0)
-		return -EPERM;
-	if (value == 1) {
-		if (macio_chips[1].type == macio_gatwick)
-			heathrow_sleep(&macio_chips[0], 1);
-		heathrow_sleep(&macio_chips[0], 0);
-	} else if (value == 0) {
-		heathrow_wakeup(&macio_chips[0], 0);
-		if (macio_chips[1].type == macio_gatwick)
-			heathrow_wakeup(&macio_chips[0], 1);
-	}
-	return 0;
-}
-
-static long
-core99_scc_enable(struct device_node* node, long param, long value)
-{
-	struct macio_chip*	macio;
-	unsigned long		flags;
-	unsigned long		chan_mask;
-	u32			fcr;
-
-	macio = macio_find(node, 0);
-	if (!macio)
-		return -ENODEV;
-	if (!strcmp(node->name, "ch-a"))
-		chan_mask = MACIO_FLAG_SCCA_ON;
-	else if (!strcmp(node->name, "ch-b"))
-		chan_mask = MACIO_FLAG_SCCB_ON;
-	else
-		return -ENODEV;
-
-	if (value) {
-		int need_reset_scc = 0;
-		int need_reset_irda = 0;
-
-		LOCK(flags);
-		fcr = MACIO_IN32(KEYLARGO_FCR0);
-		/* Check if scc cell need enabling */
-		if (!(fcr & KL0_SCC_CELL_ENABLE)) {
-			fcr |= KL0_SCC_CELL_ENABLE;
-			need_reset_scc = 1;
-		}
-		if (chan_mask & MACIO_FLAG_SCCA_ON) {
-			fcr |= KL0_SCCA_ENABLE;
-			/* Don't enable line drivers for I2S modem */
-			if ((param & 0xfff) == PMAC_SCC_I2S1)
-				fcr &= ~KL0_SCC_A_INTF_ENABLE;
-			else
-				fcr |= KL0_SCC_A_INTF_ENABLE;
-		}
-		if (chan_mask & MACIO_FLAG_SCCB_ON) {
-			fcr |= KL0_SCCB_ENABLE;
-			/* Perform irda specific inits */
-			if ((param & 0xfff) == PMAC_SCC_IRDA) {
-				fcr &= ~KL0_SCC_B_INTF_ENABLE;
-				fcr |= KL0_IRDA_ENABLE;
-				fcr |= KL0_IRDA_CLK32_ENABLE | KL0_IRDA_CLK19_ENABLE;
-				fcr |= KL0_IRDA_SOURCE1_SEL;
-				fcr &= ~(KL0_IRDA_FAST_CONNECT|KL0_IRDA_DEFAULT1|KL0_IRDA_DEFAULT0);
-				fcr &= ~(KL0_IRDA_SOURCE2_SEL|KL0_IRDA_HIGH_BAND);
-				need_reset_irda = 1;
-			} else
-				fcr |= KL0_SCC_B_INTF_ENABLE;
-		}
-		MACIO_OUT32(KEYLARGO_FCR0, fcr);
-		macio->flags |= chan_mask;
-		if (need_reset_scc)  {
-			MACIO_BIS(KEYLARGO_FCR0, KL0_SCC_RESET);
-			(void)MACIO_IN32(KEYLARGO_FCR0);
-			UNLOCK(flags);
-			mdelay(15);
-			LOCK(flags);
-			MACIO_BIC(KEYLARGO_FCR0, KL0_SCC_RESET);
-		}
-		if (need_reset_irda)  {
-			MACIO_BIS(KEYLARGO_FCR0, KL0_IRDA_RESET);
-			(void)MACIO_IN32(KEYLARGO_FCR0);
-			UNLOCK(flags);
-			mdelay(15);
-			LOCK(flags);
-			MACIO_BIC(KEYLARGO_FCR0, KL0_IRDA_RESET);
-		}
-		UNLOCK(flags);
-		if (param & PMAC_SCC_FLAG_XMON)
-			macio->flags |= MACIO_FLAG_SCC_LOCKED;
-	} else {
-		if (macio->flags & MACIO_FLAG_SCC_LOCKED)
-			return -EPERM;
-		LOCK(flags);
-		fcr = MACIO_IN32(KEYLARGO_FCR0);
-		if (chan_mask & MACIO_FLAG_SCCA_ON)
-			fcr &= ~KL0_SCCA_ENABLE;
-		if (chan_mask & MACIO_FLAG_SCCB_ON) {
-			fcr &= ~KL0_SCCB_ENABLE;
-			/* Perform irda specific clears */
-			if ((param & 0xfff) == PMAC_SCC_IRDA) {
-				fcr &= ~KL0_IRDA_ENABLE;
-				fcr &= ~(KL0_IRDA_CLK32_ENABLE | KL0_IRDA_CLK19_ENABLE);
-				fcr &= ~(KL0_IRDA_FAST_CONNECT|KL0_IRDA_DEFAULT1|KL0_IRDA_DEFAULT0);
-				fcr &= ~(KL0_IRDA_SOURCE1_SEL|KL0_IRDA_SOURCE2_SEL|KL0_IRDA_HIGH_BAND);
-			}
-		}
-		MACIO_OUT32(KEYLARGO_FCR0, fcr);
-		if ((fcr & (KL0_SCCA_ENABLE | KL0_SCCB_ENABLE)) == 0) {
-			fcr &= ~KL0_SCC_CELL_ENABLE;
-			MACIO_OUT32(KEYLARGO_FCR0, fcr);
-		}
-		macio->flags &= ~(chan_mask);
-		UNLOCK(flags);
-		mdelay(10);
-	}
-	return 0;
-}
-
-static long
-core99_modem_enable(struct device_node* node, long param, long value)
-{
-	struct macio_chip*	macio;
-	u8			gpio;
-	unsigned long		flags;
-
-	/* Hack for internal USB modem */
-	if (node == NULL) {
-		if (macio_chips[0].type != macio_keylargo)
-			return -ENODEV;
-		node = macio_chips[0].of_node;
-	}
-	macio = macio_find(node, 0);
-	if (!macio)
-		return -ENODEV;
-	gpio = MACIO_IN8(KL_GPIO_MODEM_RESET);
-	gpio |= KEYLARGO_GPIO_OUTPUT_ENABLE;
-	gpio &= ~KEYLARGO_GPIO_OUTOUT_DATA;
-
-	if (!value) {
-		LOCK(flags);
-		MACIO_OUT8(KL_GPIO_MODEM_RESET, gpio);
-		UNLOCK(flags);
-		(void)MACIO_IN8(KL_GPIO_MODEM_RESET);
-		mdelay(250);
-	}
-    	LOCK(flags);
-    	if (value) {
-    		MACIO_BIC(KEYLARGO_FCR2, KL2_ALT_DATA_OUT);
-	    	UNLOCK(flags);
-	    	(void)MACIO_IN32(KEYLARGO_FCR2);
-		mdelay(250);
-    	} else {
-    		MACIO_BIS(KEYLARGO_FCR2, KL2_ALT_DATA_OUT);
-	    	UNLOCK(flags);
-    	}
-	if (value) {
-		LOCK(flags);
-		MACIO_OUT8(KL_GPIO_MODEM_RESET, gpio | KEYLARGO_GPIO_OUTOUT_DATA);
-		(void)MACIO_IN8(KL_GPIO_MODEM_RESET);
-	    	UNLOCK(flags); mdelay(250); LOCK(flags);
-		MACIO_OUT8(KL_GPIO_MODEM_RESET, gpio);
-		(void)MACIO_IN8(KL_GPIO_MODEM_RESET);
-	    	UNLOCK(flags); mdelay(250); LOCK(flags);
-		MACIO_OUT8(KL_GPIO_MODEM_RESET, gpio | KEYLARGO_GPIO_OUTOUT_DATA);
-		(void)MACIO_IN8(KL_GPIO_MODEM_RESET);
-	    	UNLOCK(flags); mdelay(250);
-	}
-	return 0;
-}
-
-static long
-pangea_modem_enable(struct device_node* node, long param, long value)
-{
-	struct macio_chip*	macio;
-	u8			gpio;
-	unsigned long		flags;
-
-	/* Hack for internal USB modem */
-	if (node == NULL) {
-		if (macio_chips[0].type != macio_pangea &&
-		    macio_chips[0].type != macio_intrepid)
-			return -ENODEV;
-		node = macio_chips[0].of_node;
-	}
-	macio = macio_find(node, 0);
-	if (!macio)
-		return -ENODEV;
-	gpio = MACIO_IN8(KL_GPIO_MODEM_RESET);
-	gpio |= KEYLARGO_GPIO_OUTPUT_ENABLE;
-	gpio &= ~KEYLARGO_GPIO_OUTOUT_DATA;
-
-	if (!value) {
-		LOCK(flags);
-		MACIO_OUT8(KL_GPIO_MODEM_RESET, gpio);
-		UNLOCK(flags);
-		(void)MACIO_IN8(KL_GPIO_MODEM_RESET);
-		mdelay(250);
-	}
-    	LOCK(flags);
-	if (value) {
-		MACIO_OUT8(KL_GPIO_MODEM_POWER,
-			KEYLARGO_GPIO_OUTPUT_ENABLE);
-    		UNLOCK(flags);
-	    	(void)MACIO_IN32(KEYLARGO_FCR2);
-		mdelay(250);
-	} else {
-		MACIO_OUT8(KL_GPIO_MODEM_POWER,
-			KEYLARGO_GPIO_OUTPUT_ENABLE | KEYLARGO_GPIO_OUTOUT_DATA);
-    		UNLOCK(flags);
-	}
-	if (value) {
-		LOCK(flags);
-		MACIO_OUT8(KL_GPIO_MODEM_RESET, gpio | KEYLARGO_GPIO_OUTOUT_DATA);
-		(void)MACIO_IN8(KL_GPIO_MODEM_RESET);
-	    	UNLOCK(flags); mdelay(250); LOCK(flags);
-		MACIO_OUT8(KL_GPIO_MODEM_RESET, gpio);
-		(void)MACIO_IN8(KL_GPIO_MODEM_RESET);
-	    	UNLOCK(flags); mdelay(250); LOCK(flags);
-		MACIO_OUT8(KL_GPIO_MODEM_RESET, gpio | KEYLARGO_GPIO_OUTOUT_DATA);
-		(void)MACIO_IN8(KL_GPIO_MODEM_RESET);
-	    	UNLOCK(flags); mdelay(250);
-	}
-	return 0;
-}
-
-static long
-core99_ata100_enable(struct device_node* node, long value)
-{
-	unsigned long flags;
-	struct pci_dev *pdev = NULL;
-	u8 pbus, pid;
-
-    	if (uninorth_rev < 0x24)
-    		return -ENODEV;
-
-	LOCK(flags);
-	if (value)
-		UN_BIS(UNI_N_CLOCK_CNTL, UNI_N_CLOCK_CNTL_ATA100);
-	else
-		UN_BIC(UNI_N_CLOCK_CNTL, UNI_N_CLOCK_CNTL_ATA100);
-	(void)UN_IN(UNI_N_CLOCK_CNTL);
-	UNLOCK(flags);
-	udelay(20);
-
-	if (value) {
-		if (pci_device_from_OF_node(node, &pbus, &pid) == 0)
-			pdev = pci_find_slot(pbus, pid);
-		if (pdev == NULL)
-			return 0;
-		pci_enable_device(pdev);
-		pci_set_master(pdev);
-	}
-    	return 0;
-}
-
-static long
-core99_ide_enable(struct device_node* node, long param, long value)
-{
-	/* Bus ID 0 to 2 are KeyLargo based IDE, busID 3 is U2
-	 * based ata-100
-	 */
-	switch(param) {
-	    case 0:
-		return simple_feature_tweak(node, macio_unknown,
-			KEYLARGO_FCR1, KL1_EIDE0_ENABLE, value);
-	    case 1:
-		return simple_feature_tweak(node, macio_unknown,
-			KEYLARGO_FCR1, KL1_EIDE1_ENABLE, value);
-	    case 2:
-		return simple_feature_tweak(node, macio_unknown,
-			KEYLARGO_FCR1, KL1_UIDE_ENABLE, value);
-	    case 3:
-	    	return core99_ata100_enable(node, value);
-	    default:
-	    	return -ENODEV;
-	}
-}
-
-static long
-core99_ide_reset(struct device_node* node, long param, long value)
-{
-	switch(param) {
-	    case 0:
-		return simple_feature_tweak(node, macio_unknown,
-			KEYLARGO_FCR1, KL1_EIDE0_RESET_N, !value);
-	    case 1:
-		return simple_feature_tweak(node, macio_unknown,
-			KEYLARGO_FCR1, KL1_EIDE1_RESET_N, !value);
-	    case 2:
-		return simple_feature_tweak(node, macio_unknown,
-			KEYLARGO_FCR1, KL1_UIDE_RESET_N, !value);
-	    default:
-	    	return -ENODEV;
-	}
-}
-
-static long
-core99_gmac_enable(struct device_node* node, long param, long value)
-{
-	unsigned long flags;
-
-	LOCK(flags);
-	if (value)
-		UN_BIS(UNI_N_CLOCK_CNTL, UNI_N_CLOCK_CNTL_GMAC);
-	else
-		UN_BIC(UNI_N_CLOCK_CNTL, UNI_N_CLOCK_CNTL_GMAC);
-	(void)UN_IN(UNI_N_CLOCK_CNTL);
-	UNLOCK(flags);
-	udelay(20);
-
-	return 0;
-}
-
-static long
-core99_gmac_phy_reset(struct device_node* node, long param, long value)
-{
-	unsigned long flags;
-	struct macio_chip* macio;
-
-	macio = &macio_chips[0];
-	if (macio->type != macio_keylargo && macio->type != macio_pangea &&
-	    macio->type != macio_intrepid)
-		return -ENODEV;
-
-	LOCK(flags);
-	MACIO_OUT8(KL_GPIO_ETH_PHY_RESET, KEYLARGO_GPIO_OUTPUT_ENABLE);
-	(void)MACIO_IN8(KL_GPIO_ETH_PHY_RESET);
-	UNLOCK(flags);
-	mdelay(10);
-	LOCK(flags);
-	MACIO_OUT8(KL_GPIO_ETH_PHY_RESET, /*KEYLARGO_GPIO_OUTPUT_ENABLE | */
-		KEYLARGO_GPIO_OUTOUT_DATA);
-	UNLOCK(flags);
-	mdelay(10);
-
-	return 0;
-}
-
-static long
-core99_sound_chip_enable(struct device_node* node, long param, long value)
-{
-	struct macio_chip*	macio;
-	unsigned long		flags;
-
-	macio = macio_find(node, 0);
-	if (!macio)
-		return -ENODEV;
-
-	/* Do a better probe code, screamer G4 desktops &
-	 * iMacs can do that too, add a recalibrate  in
-	 * the driver as well
-	 */
-	if (pmac_mb.model_id == PMAC_TYPE_PISMO ||
-	    pmac_mb.model_id == PMAC_TYPE_TITANIUM) {
-		LOCK(flags);
-		if (value)
-	    		MACIO_OUT8(KL_GPIO_SOUND_POWER,
-	    			KEYLARGO_GPIO_OUTPUT_ENABLE |
-	    			KEYLARGO_GPIO_OUTOUT_DATA);
-	    	else
-	    		MACIO_OUT8(KL_GPIO_SOUND_POWER,
-	    			KEYLARGO_GPIO_OUTPUT_ENABLE);
-	    	(void)MACIO_IN8(KL_GPIO_SOUND_POWER);
-	    	UNLOCK(flags);
-	}
-	return 0;
-}
-
-static long
-core99_airport_enable(struct device_node* node, long param, long value)
-{
-	struct macio_chip*	macio;
-	unsigned long		flags;
-	int			state;
-
-	macio = macio_find(node, 0);
-	if (!macio)
-		return -ENODEV;
-
-	/* Hint: we allow passing of macio itself for the sake of the
-	 * sleep code
-	 */
-	if (node != macio->of_node &&
-	    (!node->parent || node->parent != macio->of_node))
-		return -ENODEV;
-	state = (macio->flags & MACIO_FLAG_AIRPORT_ON) != 0;
-	if (value == state)
-		return 0;
-	if (value) {
-		/* This code is a reproduction of OF enable-cardslot
-		 * and init-wireless methods, slightly hacked until
-		 * I got it working.
-		 */
-		LOCK(flags);
-		MACIO_OUT8(KEYLARGO_GPIO_0+0xf, 5);
-		(void)MACIO_IN8(KEYLARGO_GPIO_0+0xf);
-		UNLOCK(flags);
-		mdelay(10);
-		LOCK(flags);
-		MACIO_OUT8(KEYLARGO_GPIO_0+0xf, 4);
-		(void)MACIO_IN8(KEYLARGO_GPIO_0+0xf);
-		UNLOCK(flags);
-
-		mdelay(10);
-
-		LOCK(flags);
-		MACIO_BIC(KEYLARGO_FCR2, KL2_CARDSEL_16);
-		(void)MACIO_IN32(KEYLARGO_FCR2);
-		udelay(10);
-		MACIO_OUT8(KEYLARGO_GPIO_EXTINT_0+0xb, 0);
-		(void)MACIO_IN8(KEYLARGO_GPIO_EXTINT_0+0xb);
-		udelay(10);
-		MACIO_OUT8(KEYLARGO_GPIO_EXTINT_0+0xa, 0x28);
-		(void)MACIO_IN8(KEYLARGO_GPIO_EXTINT_0+0xa);
-		udelay(10);
-		MACIO_OUT8(KEYLARGO_GPIO_EXTINT_0+0xd, 0x28);
-		(void)MACIO_IN8(KEYLARGO_GPIO_EXTINT_0+0xd);
-		udelay(10);
-		MACIO_OUT8(KEYLARGO_GPIO_0+0xd, 0x28);
-		(void)MACIO_IN8(KEYLARGO_GPIO_0+0xd);
-		udelay(10);
-		MACIO_OUT8(KEYLARGO_GPIO_0+0xe, 0x28);
-		(void)MACIO_IN8(KEYLARGO_GPIO_0+0xe);
-		UNLOCK(flags);
-		udelay(10);
-		MACIO_OUT32(0x1c000, 0);
-		mdelay(1);
-		MACIO_OUT8(0x1a3e0, 0x41);
-		(void)MACIO_IN8(0x1a3e0);
-		udelay(10);
-		LOCK(flags);
-		MACIO_BIS(KEYLARGO_FCR2, KL2_CARDSEL_16);
-		(void)MACIO_IN32(KEYLARGO_FCR2);
-		UNLOCK(flags);
-		mdelay(100);
-
-		macio->flags |= MACIO_FLAG_AIRPORT_ON;
-	} else {
-		LOCK(flags);
-		MACIO_BIC(KEYLARGO_FCR2, KL2_CARDSEL_16);
-		(void)MACIO_IN32(KEYLARGO_FCR2);
-		MACIO_OUT8(KL_GPIO_AIRPORT_0, 0);
-		MACIO_OUT8(KL_GPIO_AIRPORT_1, 0);
-		MACIO_OUT8(KL_GPIO_AIRPORT_2, 0);
-		MACIO_OUT8(KL_GPIO_AIRPORT_3, 0);
-		MACIO_OUT8(KL_GPIO_AIRPORT_4, 0);
-		(void)MACIO_IN8(KL_GPIO_AIRPORT_4);
-		UNLOCK(flags);
-
-		macio->flags &= ~MACIO_FLAG_AIRPORT_ON;
-	}
-	return 0;
-}
-
-#ifdef CONFIG_SMP
-static long
-core99_reset_cpu(struct device_node* node, long param, long value)
-{
-	unsigned int reset_io = 0;
-	unsigned long flags;
-	struct macio_chip* macio;
-	struct device_node* np;
-	const int dflt_reset_lines[] = {	KL_GPIO_RESET_CPU0,
-						KL_GPIO_RESET_CPU1,
-						KL_GPIO_RESET_CPU2,
-						KL_GPIO_RESET_CPU3 };
-
-	macio = &macio_chips[0];
-	if (macio->type != macio_keylargo)
-		return -ENODEV;
-
-	np = find_path_device("/cpus");
-	if (np == NULL)
-		return -ENODEV;
-	for (np = np->child; np != NULL; np = np->sibling) {
-		u32* num = (u32 *)get_property(np, "reg", NULL);
-		u32* rst = (u32 *)get_property(np, "soft-reset", NULL);
-		if (num == NULL || rst == NULL)
-			continue;
-		if (param == *num) {
-			reset_io = *rst;
-			break;
-		}
-	}
-	if (np == NULL || reset_io == 0)
-		reset_io = dflt_reset_lines[param];
-
-	LOCK(flags);
-	MACIO_OUT8(reset_io, KEYLARGO_GPIO_OUTPUT_ENABLE);
-	(void)MACIO_IN8(reset_io);
-	udelay(1);
-	MACIO_OUT8(reset_io, 0);
-	(void)MACIO_IN8(reset_io);
-	UNLOCK(flags);
-
-	return 0;
-}
-#endif /* CONFIG_SMP */
-
-static long
-core99_usb_enable(struct device_node* node, long param, long value)
-{
-	struct macio_chip* macio;
-	unsigned long flags;
-	char* prop;
-	int number;
-	u32 reg;
-
-	macio = &macio_chips[0];
-	if (macio->type != macio_keylargo && macio->type != macio_pangea &&
-	    macio->type != macio_intrepid)
-		return -ENODEV;
-
-	prop = (char *)get_property(node, "AAPL,clock-id", NULL);
-	if (!prop)
-		return -ENODEV;
-	if (strncmp(prop, "usb0u048", 8) == 0)
-		number = 0;
-	else if (strncmp(prop, "usb1u148", 8) == 0)
-		number = 2;
-	else if (strncmp(prop, "usb2u248", 8) == 0)
-		number = 4;
-	else
-		return -ENODEV;
-
-	/* Sorry for the brute-force locking, but this is only used during
-	 * sleep and the timing seem to be critical
-	 */
-	LOCK(flags);
-	if (value) {
-		/* Turn ON */
-		if (number == 0) {
-			MACIO_BIC(KEYLARGO_FCR0, (KL0_USB0_PAD_SUSPEND0 | KL0_USB0_PAD_SUSPEND1));
-			(void)MACIO_IN32(KEYLARGO_FCR0);
-			UNLOCK(flags);
-			mdelay(1);
-			LOCK(flags);
-			MACIO_BIS(KEYLARGO_FCR0, KL0_USB0_CELL_ENABLE);
-		} else if (number == 2) {
-			MACIO_BIC(KEYLARGO_FCR0, (KL0_USB1_PAD_SUSPEND0 | KL0_USB1_PAD_SUSPEND1));
-			UNLOCK(flags);
-			(void)MACIO_IN32(KEYLARGO_FCR0);
-			mdelay(1);
-			LOCK(flags);
-			MACIO_BIS(KEYLARGO_FCR0, KL0_USB1_CELL_ENABLE);
-		} else if (number == 4) {
-			MACIO_BIC(KEYLARGO_FCR1, (KL1_USB2_PAD_SUSPEND0 | KL1_USB2_PAD_SUSPEND1));
-			UNLOCK(flags);
-			(void)MACIO_IN32(KEYLARGO_FCR1);
-			mdelay(1);
-			LOCK(flags);
-			MACIO_BIS(KEYLARGO_FCR1, KL1_USB2_CELL_ENABLE);
-		}
-		if (number < 4) {
-			reg = MACIO_IN32(KEYLARGO_FCR4);
-			reg &=	~(KL4_PORT_WAKEUP_ENABLE(number) | KL4_PORT_RESUME_WAKE_EN(number) |
-				KL4_PORT_CONNECT_WAKE_EN(number) | KL4_PORT_DISCONNECT_WAKE_EN(number));
-			reg &=	~(KL4_PORT_WAKEUP_ENABLE(number+1) | KL4_PORT_RESUME_WAKE_EN(number+1) |
-				KL4_PORT_CONNECT_WAKE_EN(number+1) | KL4_PORT_DISCONNECT_WAKE_EN(number+1));
-			MACIO_OUT32(KEYLARGO_FCR4, reg);
-			(void)MACIO_IN32(KEYLARGO_FCR4);
-			udelay(10);
-		} else {
-			reg = MACIO_IN32(KEYLARGO_FCR3);
-			reg &=	~(KL3_IT_PORT_WAKEUP_ENABLE(0) | KL3_IT_PORT_RESUME_WAKE_EN(0) |
-				KL3_IT_PORT_CONNECT_WAKE_EN(0) | KL3_IT_PORT_DISCONNECT_WAKE_EN(0));
-			reg &=	~(KL3_IT_PORT_WAKEUP_ENABLE(1) | KL3_IT_PORT_RESUME_WAKE_EN(1) |
-				KL3_IT_PORT_CONNECT_WAKE_EN(1) | KL3_IT_PORT_DISCONNECT_WAKE_EN(1));
-			MACIO_OUT32(KEYLARGO_FCR3, reg);
-			(void)MACIO_IN32(KEYLARGO_FCR3);
-			udelay(10);
-		}
-		if (macio->type == macio_intrepid) {
-			/* wait for clock stopped bits to clear */
-			u32 test0 = 0, test1 = 0;
-			u32 status0, status1;
-			int timeout = 1000;
-
-			UNLOCK(flags);
-			switch (number) {
-			case 0:
-				test0 = UNI_N_CLOCK_STOPPED_USB0;
-				test1 = UNI_N_CLOCK_STOPPED_USB0PCI;
-				break;
-			case 2:
-				test0 = UNI_N_CLOCK_STOPPED_USB1;
-				test1 = UNI_N_CLOCK_STOPPED_USB1PCI;
-				break;
-			case 4:
-				test0 = UNI_N_CLOCK_STOPPED_USB2;
-				test1 = UNI_N_CLOCK_STOPPED_USB2PCI;
-				break;
-			}
-			do {
-				if (--timeout <= 0) {
-					printk(KERN_ERR "core99_usb_enable: "
-					       "Timeout waiting for clocks\n");
-					break;
-				}
-				mdelay(1);
-				status0 = UN_IN(UNI_N_CLOCK_STOP_STATUS0);
-				status1 = UN_IN(UNI_N_CLOCK_STOP_STATUS1);
-			} while ((status0 & test0) | (status1 & test1));
-			LOCK(flags);
-		}
-	} else {
-		/* Turn OFF */
-		if (number < 4) {
-			reg = MACIO_IN32(KEYLARGO_FCR4);
-			reg |=	KL4_PORT_WAKEUP_ENABLE(number) | KL4_PORT_RESUME_WAKE_EN(number) |
-				KL4_PORT_CONNECT_WAKE_EN(number) | KL4_PORT_DISCONNECT_WAKE_EN(number);
-			reg |=	KL4_PORT_WAKEUP_ENABLE(number+1) | KL4_PORT_RESUME_WAKE_EN(number+1) |
-				KL4_PORT_CONNECT_WAKE_EN(number+1) | KL4_PORT_DISCONNECT_WAKE_EN(number+1);
-			MACIO_OUT32(KEYLARGO_FCR4, reg);
-			(void)MACIO_IN32(KEYLARGO_FCR4);
-			udelay(1);
-		} else {
-			reg = MACIO_IN32(KEYLARGO_FCR3);
-			reg |=	KL3_IT_PORT_WAKEUP_ENABLE(0) | KL3_IT_PORT_RESUME_WAKE_EN(0) |
-				KL3_IT_PORT_CONNECT_WAKE_EN(0) | KL3_IT_PORT_DISCONNECT_WAKE_EN(0);
-			reg |=	KL3_IT_PORT_WAKEUP_ENABLE(1) | KL3_IT_PORT_RESUME_WAKE_EN(1) |
-				KL3_IT_PORT_CONNECT_WAKE_EN(1) | KL3_IT_PORT_DISCONNECT_WAKE_EN(1);
-			MACIO_OUT32(KEYLARGO_FCR3, reg);
-			(void)MACIO_IN32(KEYLARGO_FCR3);
-			udelay(1);
-		}
-		if (number == 0) {
-			if (macio->type != macio_intrepid)
-				MACIO_BIC(KEYLARGO_FCR0, KL0_USB0_CELL_ENABLE);
-			(void)MACIO_IN32(KEYLARGO_FCR0);
-			udelay(1);
-			MACIO_BIS(KEYLARGO_FCR0, (KL0_USB0_PAD_SUSPEND0 | KL0_USB0_PAD_SUSPEND1));
-			(void)MACIO_IN32(KEYLARGO_FCR0);
-		} else if (number == 2) {
-			if (macio->type != macio_intrepid)
-				MACIO_BIC(KEYLARGO_FCR0, KL0_USB1_CELL_ENABLE);
-			(void)MACIO_IN32(KEYLARGO_FCR0);
-			udelay(1);
-			MACIO_BIS(KEYLARGO_FCR0, (KL0_USB1_PAD_SUSPEND0 | KL0_USB1_PAD_SUSPEND1));
-			(void)MACIO_IN32(KEYLARGO_FCR0);
-		} else if (number == 4) {
-			udelay(1);
-			MACIO_BIS(KEYLARGO_FCR1, (KL1_USB2_PAD_SUSPEND0 | KL1_USB2_PAD_SUSPEND1));
-			(void)MACIO_IN32(KEYLARGO_FCR1);
-		}
-		udelay(1);
-	}
-	UNLOCK(flags);
-
-	return 0;
-}
-
-static long
-core99_firewire_enable(struct device_node* node, long param, long value)
-{
-	unsigned long flags;
-	struct macio_chip* macio;
-
-	macio = &macio_chips[0];
-	if (macio->type != macio_keylargo && macio->type != macio_pangea &&
-	    macio->type != macio_intrepid)
-		return -ENODEV;
-	if (!(macio->flags & MACIO_FLAG_FW_SUPPORTED))
-		return -ENODEV;
-
-	LOCK(flags);
-	if (value) {
-		UN_BIS(UNI_N_CLOCK_CNTL, UNI_N_CLOCK_CNTL_FW);
-		(void)UN_IN(UNI_N_CLOCK_CNTL);
-	} else {
-		UN_BIC(UNI_N_CLOCK_CNTL, UNI_N_CLOCK_CNTL_FW);
-		(void)UN_IN(UNI_N_CLOCK_CNTL);
-	}
-	UNLOCK(flags);
-	mdelay(1);
-
-	return 0;
-}
-
-static long
-core99_firewire_cable_power(struct device_node* node, long param, long value)
-{
-	unsigned long flags;
-	struct macio_chip* macio;
-
-	/* Trick: we allow NULL node */
-	if ((pmac_mb.board_flags & PMAC_MB_HAS_FW_POWER) == 0)
-	    	return -ENODEV;
-	macio = &macio_chips[0];
-	if (macio->type != macio_keylargo && macio->type != macio_pangea &&
-	    macio->type != macio_intrepid)
-		return -ENODEV;
-	if (!(macio->flags & MACIO_FLAG_FW_SUPPORTED))
-		return -ENODEV;
-
-	LOCK(flags);
-	if (value) {
-		MACIO_OUT8(KL_GPIO_FW_CABLE_POWER , 0);
-		MACIO_IN8(KL_GPIO_FW_CABLE_POWER);
-		udelay(10);
-	} else {
-		MACIO_OUT8(KL_GPIO_FW_CABLE_POWER , 4);
-		MACIO_IN8(KL_GPIO_FW_CABLE_POWER); udelay(10);
-	}
-	UNLOCK(flags);
-	mdelay(1);
-
-	return 0;
-}
-
-static long
-intrepid_aack_delay_enable(struct device_node* node, long param, long value)
-{
-	unsigned long flags;
-
-    	if (uninorth_rev < 0xd2)
-		return -ENODEV;
-
-	LOCK(flags);
-	if (param)
-		UN_BIS(UNI_N_AACK_DELAY, UNI_N_AACK_DELAY_ENABLE);
-	else
-		UN_BIC(UNI_N_AACK_DELAY, UNI_N_AACK_DELAY_ENABLE);
-	UNLOCK(flags);
-
-    	return 0;
-}
-
-
-#endif /* CONFIG_POWER4 */
-
-static long
-core99_read_gpio(struct device_node* node, long param, long value)
-{
-	struct macio_chip* macio = &macio_chips[0];
-
-	return MACIO_IN8(param);
-}
-
-
-static long
-core99_write_gpio(struct device_node* node, long param, long value)
-{
-	struct macio_chip* macio = &macio_chips[0];
-
-	MACIO_OUT8(param, (u8)(value & 0xff));
-	return 0;
-}
-
-#ifdef CONFIG_POWER4
-
-static long
-g5_gmac_enable(struct device_node* node, long param, long value)
-{
-	struct macio_chip* macio = &macio_chips[0];
-	unsigned long flags;
-	u8 pbus, pid;
-
-	LOCK(flags);
-	if (value) {
-		MACIO_BIS(KEYLARGO_FCR1, K2_FCR1_GMAC_CLK_ENABLE);
-		mb();
-		k2_skiplist[0] = NULL;
-	} else {
-		k2_skiplist[0] = node;
-		mb();
-		MACIO_BIC(KEYLARGO_FCR1, K2_FCR1_GMAC_CLK_ENABLE);
-	}
-	
-	UNLOCK(flags);
-	mdelay(1);
-
-	return 0;
-}
-
-static long
-g5_fw_enable(struct device_node* node, long param, long value)
-{
-	struct macio_chip* macio = &macio_chips[0];
-	unsigned long flags;
-
-	LOCK(flags);
-	if (value) {
-		MACIO_BIS(KEYLARGO_FCR1, K2_FCR1_FW_CLK_ENABLE);
-		mb();
-		k2_skiplist[1] = NULL;
-	} else {
-		k2_skiplist[1] = node;
-		mb();
-		MACIO_BIC(KEYLARGO_FCR1, K2_FCR1_FW_CLK_ENABLE);
-	}
-	
-	UNLOCK(flags);
-	mdelay(1);
-
-	return 0;
-}
-
-static long
-g5_mpic_enable(struct device_node* node, long param, long value)
-{
-	unsigned long flags;
-
-	if (node->parent == NULL || strcmp(node->parent->name, "u3"))
-		return 0;
-
-	LOCK(flags);
-	UN_BIS(U3_TOGGLE_REG, U3_MPIC_RESET | U3_MPIC_OUTPUT_ENABLE);
-	UNLOCK(flags);
-
-	return 0;
-}
-
-#ifdef CONFIG_SMP
-static long
-g5_reset_cpu(struct device_node* node, long param, long value)
-{
-	unsigned int reset_io = 0;
-	unsigned long flags;
-	struct macio_chip* macio;
-	struct device_node* np;
-
-	macio = &macio_chips[0];
-	if (macio->type != macio_keylargo2)
-		return -ENODEV;
-
-	np = find_path_device("/cpus");
-	if (np == NULL)
-		return -ENODEV;
-	for (np = np->child; np != NULL; np = np->sibling) {
-		u32* num = (u32 *)get_property(np, "reg", NULL);
-		u32* rst = (u32 *)get_property(np, "soft-reset", NULL);
-		if (num == NULL || rst == NULL)
-			continue;
-		if (param == *num) {
-			reset_io = *rst;
-			break;
-		}
-	}
-	if (np == NULL || reset_io == 0)
-		return -ENODEV;
-
-	LOCK(flags);
-	MACIO_OUT8(reset_io, KEYLARGO_GPIO_OUTPUT_ENABLE);
-	(void)MACIO_IN8(reset_io);
-	udelay(1);
-	MACIO_OUT8(reset_io, 0);
-	(void)MACIO_IN8(reset_io);
-	UNLOCK(flags);
-
-	return 0;
-}
-#endif /* CONFIG_SMP */
-
-/*
- * This can be called from pmac_smp so isn't static
- *
- * This takes the second CPU off the bus on dual CPU machines
- * running UP
- */
-void g5_phy_disable_cpu1(void)
-{
-	UN_OUT(U3_API_PHY_CONFIG_1, 0);
-}
-
-#endif /* CONFIG_POWER4 */
-
-#ifndef CONFIG_POWER4
-
-static void
-keylargo_shutdown(struct macio_chip* macio, int sleep_mode)
-{
-	u32 temp;
-
-	if (sleep_mode) {
-		mdelay(1);
-		MACIO_BIS(KEYLARGO_FCR0, KL0_USB_REF_SUSPEND);
-		(void)MACIO_IN32(KEYLARGO_FCR0);
-		mdelay(1);
-	}
-
-	MACIO_BIC(KEYLARGO_FCR0,KL0_SCCA_ENABLE | KL0_SCCB_ENABLE |
-				KL0_SCC_CELL_ENABLE |
-		      		KL0_IRDA_ENABLE | KL0_IRDA_CLK32_ENABLE |
-		      		KL0_IRDA_CLK19_ENABLE);
-
-	MACIO_BIC(KEYLARGO_MBCR, KL_MBCR_MB0_DEV_MASK);
-	MACIO_BIS(KEYLARGO_MBCR, KL_MBCR_MB0_IDE_ENABLE);
-
-	MACIO_BIC(KEYLARGO_FCR1,
-		KL1_AUDIO_SEL_22MCLK | KL1_AUDIO_CLK_ENABLE_BIT |
-		KL1_AUDIO_CLK_OUT_ENABLE | KL1_AUDIO_CELL_ENABLE |
-		KL1_I2S0_CELL_ENABLE | KL1_I2S0_CLK_ENABLE_BIT |
-		KL1_I2S0_ENABLE | KL1_I2S1_CELL_ENABLE |
-		KL1_I2S1_CLK_ENABLE_BIT | KL1_I2S1_ENABLE |
-		KL1_EIDE0_ENABLE | KL1_EIDE0_RESET_N |
-		KL1_EIDE1_ENABLE | KL1_EIDE1_RESET_N |
-		KL1_UIDE_ENABLE);
-
-	MACIO_BIS(KEYLARGO_FCR2, KL2_ALT_DATA_OUT);
- 	MACIO_BIC(KEYLARGO_FCR2, KL2_IOBUS_ENABLE);
-
-	temp = MACIO_IN32(KEYLARGO_FCR3);
-	if (macio->rev >= 2) {
-		temp |= KL3_SHUTDOWN_PLL2X;
-		if (sleep_mode)
-			temp |= KL3_SHUTDOWN_PLL_TOTAL;
-	}
-
-	temp |= KL3_SHUTDOWN_PLLKW6 | KL3_SHUTDOWN_PLLKW4 |
-		KL3_SHUTDOWN_PLLKW35;
-	if (sleep_mode)
-		temp |= KL3_SHUTDOWN_PLLKW12;
-	temp &= ~(KL3_CLK66_ENABLE | KL3_CLK49_ENABLE | KL3_CLK45_ENABLE
-		| KL3_CLK31_ENABLE | KL3_I2S1_CLK18_ENABLE | KL3_I2S0_CLK18_ENABLE);
-	if (sleep_mode)
-		temp &= ~(KL3_TIMER_CLK18_ENABLE | KL3_VIA_CLK16_ENABLE);
-	MACIO_OUT32(KEYLARGO_FCR3, temp);
-
-	/* Flush posted writes & wait a bit */
-	(void)MACIO_IN32(KEYLARGO_FCR0); mdelay(1);
-}
-
-static void
-pangea_shutdown(struct macio_chip* macio, int sleep_mode)
-{
-	u32 temp;
-
-	MACIO_BIC(KEYLARGO_FCR0,KL0_SCCA_ENABLE | KL0_SCCB_ENABLE |
-				KL0_SCC_CELL_ENABLE |
-				KL0_USB0_CELL_ENABLE | KL0_USB1_CELL_ENABLE);
-
-	MACIO_BIC(KEYLARGO_FCR1,
-		KL1_AUDIO_SEL_22MCLK | KL1_AUDIO_CLK_ENABLE_BIT |
-		KL1_AUDIO_CLK_OUT_ENABLE | KL1_AUDIO_CELL_ENABLE |
-		KL1_I2S0_CELL_ENABLE | KL1_I2S0_CLK_ENABLE_BIT |
-		KL1_I2S0_ENABLE | KL1_I2S1_CELL_ENABLE |
-		KL1_I2S1_CLK_ENABLE_BIT | KL1_I2S1_ENABLE |
-		KL1_UIDE_ENABLE);
-	if (pmac_mb.board_flags & PMAC_MB_MOBILE)
-		MACIO_BIC(KEYLARGO_FCR1, KL1_UIDE_RESET_N);
-
-	MACIO_BIS(KEYLARGO_FCR2, KL2_ALT_DATA_OUT);
-
-	temp = MACIO_IN32(KEYLARGO_FCR3);
-	temp |= KL3_SHUTDOWN_PLLKW6 | KL3_SHUTDOWN_PLLKW4 |
-		KL3_SHUTDOWN_PLLKW35;
-	temp &= ~(KL3_CLK49_ENABLE | KL3_CLK45_ENABLE | KL3_CLK31_ENABLE
-		| KL3_I2S0_CLK18_ENABLE | KL3_I2S1_CLK18_ENABLE);
-	if (sleep_mode)
-		temp &= ~(KL3_VIA_CLK16_ENABLE | KL3_TIMER_CLK18_ENABLE);
-	MACIO_OUT32(KEYLARGO_FCR3, temp);
-
-	/* Flush posted writes & wait a bit */
-	(void)MACIO_IN32(KEYLARGO_FCR0); mdelay(1);
-}
-
-static void
-intrepid_shutdown(struct macio_chip* macio, int sleep_mode)
-{
-	u32 temp;
-
-	MACIO_BIC(KEYLARGO_FCR0,KL0_SCCA_ENABLE | KL0_SCCB_ENABLE |
-		  KL0_SCC_CELL_ENABLE);
-
-	MACIO_BIC(KEYLARGO_FCR1,
-		  /*KL1_USB2_CELL_ENABLE |*/
-		KL1_I2S0_CELL_ENABLE | KL1_I2S0_CLK_ENABLE_BIT |
-		KL1_I2S0_ENABLE | KL1_I2S1_CELL_ENABLE |
-		KL1_I2S1_CLK_ENABLE_BIT | KL1_I2S1_ENABLE);
-	if (pmac_mb.board_flags & PMAC_MB_MOBILE)
-		MACIO_BIC(KEYLARGO_FCR1, KL1_UIDE_RESET_N);
-
-	temp = MACIO_IN32(KEYLARGO_FCR3);
-	temp &= ~(KL3_CLK49_ENABLE | KL3_CLK45_ENABLE |
-		  KL3_I2S1_CLK18_ENABLE | KL3_I2S0_CLK18_ENABLE);
-	if (sleep_mode)
-		temp &= ~(KL3_TIMER_CLK18_ENABLE | KL3_IT_VIA_CLK32_ENABLE);
-	MACIO_OUT32(KEYLARGO_FCR3, temp);
-
-	/* Flush posted writes & wait a bit */
-	(void)MACIO_IN32(KEYLARGO_FCR0);
-	mdelay(10);
-}
-
-
-void pmac_tweak_clock_spreading(int enable)
-{
-	struct macio_chip* macio = &macio_chips[0];
-
-	/* Hack for doing clock spreading on some machines PowerBooks and
-	 * iBooks. This implements the "platform-do-clockspreading" OF
-	 * property as decoded manually on various models. For safety, we also
-	 * check the product ID in the device-tree in cases we'll whack the i2c
-	 * chip to make reasonably sure we won't set wrong values in there
-	 *
-	 * Of course, ultimately, we have to implement a real parser for
-	 * the platform-do-* stuff...
-	 */
-
-	if (macio->type == macio_intrepid) {
-		struct device_node *clock =
-			of_find_node_by_path("/uni-n@f8000000/hw-clock");
-		if (clock && get_property(clock, "platform-do-clockspreading",
-					  NULL)) {
-			printk(KERN_INFO "%sabling clock spreading on Intrepid"
-			       " ASIC\n", enable ? "En" : "Dis");
-			if (enable)
-				UN_OUT(UNI_N_CLOCK_SPREADING, 2);
-			else
-				UN_OUT(UNI_N_CLOCK_SPREADING, 0);
-			mdelay(40);
-		}
-		of_node_put(clock);
-	}
-
-	while (machine_is_compatible("PowerBook5,2") ||
-	       machine_is_compatible("PowerBook5,3") ||
-	       machine_is_compatible("PowerBook6,2") ||
-	       machine_is_compatible("PowerBook6,3")) {
-		struct device_node *ui2c = of_find_node_by_type(NULL, "i2c");
-		struct device_node *dt = of_find_node_by_name(NULL, "device-tree");
-		u8 buffer[9];
-		u32 *productID;
-		int i, rc, changed = 0;
-
-		if (dt == NULL)
-			break;
-		productID = (u32 *)get_property(dt, "pid#", NULL);
-		if (productID == NULL)
-			break;
-		while(ui2c) {
-			struct device_node *p = of_get_parent(ui2c);
-			if (p && !strcmp(p->name, "uni-n"))
-				break;
-			ui2c = of_find_node_by_type(ui2c, "i2c");
-		}
-		if (ui2c == NULL)
-			break;
-		DBG("Trying to bump clock speed for PID: %08x...\n", *productID);
-		rc = pmac_low_i2c_open(ui2c, 1);
-		if (rc != 0)
-			break;
-		pmac_low_i2c_setmode(ui2c, pmac_low_i2c_mode_combined);
-		rc = pmac_low_i2c_xfer(ui2c, 0xd2 | pmac_low_i2c_read, 0x80, buffer, 9);
-		DBG("read result: %d,", rc);
-		if (rc != 0) {
-			pmac_low_i2c_close(ui2c);
-			break;
-		}
-		for (i=0; i<9; i++)
-			DBG(" %02x", buffer[i]);
-		DBG("\n");
-
-		switch(*productID) {
-		case 0x1182:	/* AlBook 12" rev 2 */
-		case 0x1183:	/* iBook G4 12" */
-			buffer[0] = (buffer[0] & 0x8f) | 0x70;
-			buffer[2] = (buffer[2] & 0x7f) | 0x00;
-			buffer[5] = (buffer[5] & 0x80) | 0x31;
-			buffer[6] = (buffer[6] & 0x40) | 0xb0;
-			buffer[7] = (buffer[7] & 0x00) | (enable ? 0xc0 : 0xba);
-			buffer[8] = (buffer[8] & 0x00) | 0x30;
-			changed = 1;
-			break;
-		case 0x3142:	/* AlBook 15" (ATI M10) */
-		case 0x3143:	/* AlBook 17" (ATI M10) */
-			buffer[0] = (buffer[0] & 0xaf) | 0x50;
-			buffer[2] = (buffer[2] & 0x7f) | 0x00;
-			buffer[5] = (buffer[5] & 0x80) | 0x31;
-			buffer[6] = (buffer[6] & 0x40) | 0xb0;
-			buffer[7] = (buffer[7] & 0x00) | (enable ? 0xd0 : 0xc0);
-			buffer[8] = (buffer[8] & 0x00) | 0x30;
-			changed = 1;
-			break;
-		default:
-			DBG("i2c-hwclock: Machine model not handled\n");
-			break;
-		}
-		if (!changed) {
-			pmac_low_i2c_close(ui2c);
-			break;
-		}
-		printk(KERN_INFO "%sabling clock spreading on i2c clock chip\n",
-		       enable ? "En" : "Dis");
-		pmac_low_i2c_setmode(ui2c, pmac_low_i2c_mode_stdsub);
-		rc = pmac_low_i2c_xfer(ui2c, 0xd2 | pmac_low_i2c_write, 0x80, buffer, 9);
-		DBG("write result: %d,", rc);
-		pmac_low_i2c_setmode(ui2c, pmac_low_i2c_mode_combined);
-		rc = pmac_low_i2c_xfer(ui2c, 0xd2 | pmac_low_i2c_read, 0x80, buffer, 9);
-		DBG("read result: %d,", rc);
-		if (rc != 0) {
-			pmac_low_i2c_close(ui2c);
-			break;
-		}
-		for (i=0; i<9; i++)
-			DBG(" %02x", buffer[i]);
-		pmac_low_i2c_close(ui2c);
-		break;
-	}
-}
-
-
-static int
-core99_sleep(void)
-{
-	struct macio_chip* macio;
-	int i;
-
-	macio = &macio_chips[0];
-	if (macio->type != macio_keylargo && macio->type != macio_pangea &&
-	    macio->type != macio_intrepid)
-		return -ENODEV;
-
-	/* We power off the wireless slot in case it was not done
-	 * by the driver. We don't power it on automatically however
-	 */
-	if (macio->flags & MACIO_FLAG_AIRPORT_ON)
-		core99_airport_enable(macio->of_node, 0, 0);
-
-	/* We power off the FW cable. Should be done by the driver... */
-	if (macio->flags & MACIO_FLAG_FW_SUPPORTED) {
-		core99_firewire_enable(NULL, 0, 0);
-		core99_firewire_cable_power(NULL, 0, 0);
-	}
-
-	/* We make sure int. modem is off (in case driver lost it) */
-	if (macio->type == macio_keylargo)
-		core99_modem_enable(macio->of_node, 0, 0);
-	else
-		pangea_modem_enable(macio->of_node, 0, 0);
-
-	/* We make sure the sound is off as well */
-	core99_sound_chip_enable(macio->of_node, 0, 0);
-
-	/*
-	 * Save various bits of KeyLargo
-	 */
-
-	/* Save the state of the various GPIOs */
-	save_gpio_levels[0] = MACIO_IN32(KEYLARGO_GPIO_LEVELS0);
-	save_gpio_levels[1] = MACIO_IN32(KEYLARGO_GPIO_LEVELS1);
-	for (i=0; i<KEYLARGO_GPIO_EXTINT_CNT; i++)
-		save_gpio_extint[i] = MACIO_IN8(KEYLARGO_GPIO_EXTINT_0+i);
-	for (i=0; i<KEYLARGO_GPIO_CNT; i++)
-		save_gpio_normal[i] = MACIO_IN8(KEYLARGO_GPIO_0+i);
-
-	/* Save the FCRs */
-	if (macio->type == macio_keylargo)
-		save_mbcr = MACIO_IN32(KEYLARGO_MBCR);
-	save_fcr[0] = MACIO_IN32(KEYLARGO_FCR0);
-	save_fcr[1] = MACIO_IN32(KEYLARGO_FCR1);
-	save_fcr[2] = MACIO_IN32(KEYLARGO_FCR2);
-	save_fcr[3] = MACIO_IN32(KEYLARGO_FCR3);
-	save_fcr[4] = MACIO_IN32(KEYLARGO_FCR4);
-	if (macio->type == macio_pangea || macio->type == macio_intrepid)
-		save_fcr[5] = MACIO_IN32(KEYLARGO_FCR5);
-
-	/* Save state & config of DBDMA channels */
-	dbdma_save(macio, save_dbdma);
-
-	/*
-	 * Turn off as much as we can
-	 */
-	if (macio->type == macio_pangea)
-		pangea_shutdown(macio, 1);
-	else if (macio->type == macio_intrepid)
-		intrepid_shutdown(macio, 1);
-	else if (macio->type == macio_keylargo)
-		keylargo_shutdown(macio, 1);
-
-	/*
-	 * Put the host bridge to sleep
-	 */
-
-	save_unin_clock_ctl = UN_IN(UNI_N_CLOCK_CNTL);
-	/* Note: do not switch GMAC off, driver does it when necessary, WOL must keep it
-	 * enabled !
-	 */
-	UN_OUT(UNI_N_CLOCK_CNTL, save_unin_clock_ctl &
-	       ~(/*UNI_N_CLOCK_CNTL_GMAC|*/UNI_N_CLOCK_CNTL_FW/*|UNI_N_CLOCK_CNTL_PCI*/));
-	udelay(100);
-	UN_OUT(UNI_N_HWINIT_STATE, UNI_N_HWINIT_STATE_SLEEPING);
-	UN_OUT(UNI_N_POWER_MGT, UNI_N_POWER_MGT_SLEEP);
-	mdelay(10);
-
-	/*
-	 * FIXME: A bit of black magic with OpenPIC (don't ask me why)
-	 */
-	if (pmac_mb.model_id == PMAC_TYPE_SAWTOOTH) {
-		MACIO_BIS(0x506e0, 0x00400000);
-		MACIO_BIS(0x506e0, 0x80000000);
-	}
-	return 0;
-}
-
-static int
-core99_wake_up(void)
-{
-	struct macio_chip* macio;
-	int i;
-
-	macio = &macio_chips[0];
-	if (macio->type != macio_keylargo && macio->type != macio_pangea &&
-	    macio->type != macio_intrepid)
-		return -ENODEV;
-
-	/*
-	 * Wakeup the host bridge
-	 */
-	UN_OUT(UNI_N_POWER_MGT, UNI_N_POWER_MGT_NORMAL);
-	udelay(10);
-	UN_OUT(UNI_N_HWINIT_STATE, UNI_N_HWINIT_STATE_RUNNING);
-	udelay(10);
-
-	/*
-	 * Restore KeyLargo
-	 */
-
-	if (macio->type == macio_keylargo) {
-		MACIO_OUT32(KEYLARGO_MBCR, save_mbcr);
-		(void)MACIO_IN32(KEYLARGO_MBCR); udelay(10);
-	}
-	MACIO_OUT32(KEYLARGO_FCR0, save_fcr[0]);
-	(void)MACIO_IN32(KEYLARGO_FCR0); udelay(10);
-	MACIO_OUT32(KEYLARGO_FCR1, save_fcr[1]);
-	(void)MACIO_IN32(KEYLARGO_FCR1); udelay(10);
-	MACIO_OUT32(KEYLARGO_FCR2, save_fcr[2]);
-	(void)MACIO_IN32(KEYLARGO_FCR2); udelay(10);
-	MACIO_OUT32(KEYLARGO_FCR3, save_fcr[3]);
-	(void)MACIO_IN32(KEYLARGO_FCR3); udelay(10);
-	MACIO_OUT32(KEYLARGO_FCR4, save_fcr[4]);
-	(void)MACIO_IN32(KEYLARGO_FCR4); udelay(10);
-	if (macio->type == macio_pangea || macio->type == macio_intrepid) {
-		MACIO_OUT32(KEYLARGO_FCR5, save_fcr[5]);
-		(void)MACIO_IN32(KEYLARGO_FCR5); udelay(10);
-	}
-
-	dbdma_restore(macio, save_dbdma);
-
-	MACIO_OUT32(KEYLARGO_GPIO_LEVELS0, save_gpio_levels[0]);
-	MACIO_OUT32(KEYLARGO_GPIO_LEVELS1, save_gpio_levels[1]);
-	for (i=0; i<KEYLARGO_GPIO_EXTINT_CNT; i++)
-		MACIO_OUT8(KEYLARGO_GPIO_EXTINT_0+i, save_gpio_extint[i]);
-	for (i=0; i<KEYLARGO_GPIO_CNT; i++)
-		MACIO_OUT8(KEYLARGO_GPIO_0+i, save_gpio_normal[i]);
-
-	/* FIXME more black magic with OpenPIC ... */
-	if (pmac_mb.model_id == PMAC_TYPE_SAWTOOTH) {
-		MACIO_BIC(0x506e0, 0x00400000);
-		MACIO_BIC(0x506e0, 0x80000000);
-	}
-
-	UN_OUT(UNI_N_CLOCK_CNTL, save_unin_clock_ctl);
-	udelay(100);
-
-	return 0;
-}
-
-static long
-core99_sleep_state(struct device_node* node, long param, long value)
-{
-	/* Param == 1 means to enter the "fake sleep" mode that is
-	 * used for CPU speed switch
-	 */
-	if (param == 1) {
-		if (value == 1) {
-			UN_OUT(UNI_N_HWINIT_STATE, UNI_N_HWINIT_STATE_SLEEPING);
-			UN_OUT(UNI_N_POWER_MGT, UNI_N_POWER_MGT_IDLE2);
-		} else {
-			UN_OUT(UNI_N_POWER_MGT, UNI_N_POWER_MGT_NORMAL);
-			udelay(10);
-			UN_OUT(UNI_N_HWINIT_STATE, UNI_N_HWINIT_STATE_RUNNING);
-			udelay(10);
-		}
-		return 0;
-	}
-	if ((pmac_mb.board_flags & PMAC_MB_CAN_SLEEP) == 0)
-		return -EPERM;
-
-	if (value == 1)
-		return core99_sleep();
-	else if (value == 0)
-		return core99_wake_up();
-	return 0;
-}
-
-#endif /* CONFIG_POWER4 */
-
-static long
-generic_dev_can_wake(struct device_node* node, long param, long value)
-{
-	/* Todo: eventually check we are really dealing with on-board
-	 * video device ...
-	 */
-
-	if (pmac_mb.board_flags & PMAC_MB_MAY_SLEEP)
-		pmac_mb.board_flags |= PMAC_MB_CAN_SLEEP;
-	return 0;
-}
-
-static long
-generic_get_mb_info(struct device_node* node, long param, long value)
-{
-	switch(param) {
-		case PMAC_MB_INFO_MODEL:
-			return pmac_mb.model_id;
-		case PMAC_MB_INFO_FLAGS:
-			return pmac_mb.board_flags;
-		case PMAC_MB_INFO_NAME:
-			/* hack hack hack... but should work */
-			*((const char **)value) = pmac_mb.model_name;
-			return 0;
-	}
-	return -EINVAL;
-}
-
-
-/*
- * Table definitions
- */
-
-/* Used on any machine
- */
-static struct feature_table_entry any_features[] = {
-	{ PMAC_FTR_GET_MB_INFO,		generic_get_mb_info },
-	{ PMAC_FTR_DEVICE_CAN_WAKE,	generic_dev_can_wake },
-	{ 0, NULL }
-};
-
-#ifndef CONFIG_POWER4
-
-/* OHare based motherboards. Currently, we only use these on the
- * 2400,3400 and 3500 series powerbooks. Some older desktops seem
- * to have issues with turning on/off those asic cells
- */
-static struct feature_table_entry ohare_features[] = {
-	{ PMAC_FTR_SCC_ENABLE,		ohare_htw_scc_enable },
-	{ PMAC_FTR_SWIM3_ENABLE,	ohare_floppy_enable },
-	{ PMAC_FTR_MESH_ENABLE,		ohare_mesh_enable },
-	{ PMAC_FTR_IDE_ENABLE,		ohare_ide_enable},
-	{ PMAC_FTR_IDE_RESET,		ohare_ide_reset},
-	{ PMAC_FTR_SLEEP_STATE,		ohare_sleep_state },
-	{ 0, NULL }
-};
-
-/* Heathrow desktop machines (Beige G3).
- * Separated as some features couldn't be properly tested
- * and the serial port control bits appear to confuse it.
- */
-static struct feature_table_entry heathrow_desktop_features[] = {
-	{ PMAC_FTR_SWIM3_ENABLE,	heathrow_floppy_enable },
-	{ PMAC_FTR_MESH_ENABLE,		heathrow_mesh_enable },
-	{ PMAC_FTR_IDE_ENABLE,		heathrow_ide_enable },
-	{ PMAC_FTR_IDE_RESET,		heathrow_ide_reset },
-	{ PMAC_FTR_BMAC_ENABLE,		heathrow_bmac_enable },
-	{ 0, NULL }
-};
-
-/* Heathrow based laptop, that is the Wallstreet and mainstreet
- * powerbooks.
- */
-static struct feature_table_entry heathrow_laptop_features[] = {
-	{ PMAC_FTR_SCC_ENABLE,		ohare_htw_scc_enable },
-	{ PMAC_FTR_MODEM_ENABLE,	heathrow_modem_enable },
-	{ PMAC_FTR_SWIM3_ENABLE,	heathrow_floppy_enable },
-	{ PMAC_FTR_MESH_ENABLE,		heathrow_mesh_enable },
-	{ PMAC_FTR_IDE_ENABLE,		heathrow_ide_enable },
-	{ PMAC_FTR_IDE_RESET,		heathrow_ide_reset },
-	{ PMAC_FTR_BMAC_ENABLE,		heathrow_bmac_enable },
-	{ PMAC_FTR_SOUND_CHIP_ENABLE,	heathrow_sound_enable },
-	{ PMAC_FTR_SLEEP_STATE,		heathrow_sleep_state },
-	{ 0, NULL }
-};
-
-/* Paddington based machines
- * The lombard (101) powerbook, first iMac models, B&W G3 and Yikes G4.
- */
-static struct feature_table_entry paddington_features[] = {
-	{ PMAC_FTR_SCC_ENABLE,		ohare_htw_scc_enable },
-	{ PMAC_FTR_MODEM_ENABLE,	heathrow_modem_enable },
-	{ PMAC_FTR_SWIM3_ENABLE,	heathrow_floppy_enable },
-	{ PMAC_FTR_MESH_ENABLE,		heathrow_mesh_enable },
-	{ PMAC_FTR_IDE_ENABLE,		heathrow_ide_enable },
-	{ PMAC_FTR_IDE_RESET,		heathrow_ide_reset },
-	{ PMAC_FTR_BMAC_ENABLE,		heathrow_bmac_enable },
-	{ PMAC_FTR_SOUND_CHIP_ENABLE,	heathrow_sound_enable },
-	{ PMAC_FTR_SLEEP_STATE,		heathrow_sleep_state },
-	{ 0, NULL }
-};
-
-/* Core99 & MacRISC 2 machines (all machines released since the
- * iBook (included), that is all AGP machines, except pangea
- * chipset. The pangea chipset is the "combo" UniNorth/KeyLargo
- * used on iBook2 & iMac "flow power".
- */
-static struct feature_table_entry core99_features[] = {
-	{ PMAC_FTR_SCC_ENABLE,		core99_scc_enable },
-	{ PMAC_FTR_MODEM_ENABLE,	core99_modem_enable },
-	{ PMAC_FTR_IDE_ENABLE,		core99_ide_enable },
-	{ PMAC_FTR_IDE_RESET,		core99_ide_reset },
-	{ PMAC_FTR_GMAC_ENABLE,		core99_gmac_enable },
-	{ PMAC_FTR_GMAC_PHY_RESET,	core99_gmac_phy_reset },
-	{ PMAC_FTR_SOUND_CHIP_ENABLE,	core99_sound_chip_enable },
-	{ PMAC_FTR_AIRPORT_ENABLE,	core99_airport_enable },
-	{ PMAC_FTR_USB_ENABLE,		core99_usb_enable },
-	{ PMAC_FTR_1394_ENABLE,		core99_firewire_enable },
-	{ PMAC_FTR_1394_CABLE_POWER,	core99_firewire_cable_power },
-	{ PMAC_FTR_SLEEP_STATE,		core99_sleep_state },
-#ifdef CONFIG_SMP
-	{ PMAC_FTR_RESET_CPU,		core99_reset_cpu },
-#endif /* CONFIG_SMP */
-	{ PMAC_FTR_READ_GPIO,		core99_read_gpio },
-	{ PMAC_FTR_WRITE_GPIO,		core99_write_gpio },
-	{ 0, NULL }
-};
-
-/* RackMac
- */
-static struct feature_table_entry rackmac_features[] = {
-	{ PMAC_FTR_SCC_ENABLE,		core99_scc_enable },
-	{ PMAC_FTR_IDE_ENABLE,		core99_ide_enable },
-	{ PMAC_FTR_IDE_RESET,		core99_ide_reset },
-	{ PMAC_FTR_GMAC_ENABLE,		core99_gmac_enable },
-	{ PMAC_FTR_GMAC_PHY_RESET,	core99_gmac_phy_reset },
-	{ PMAC_FTR_USB_ENABLE,		core99_usb_enable },
-	{ PMAC_FTR_1394_ENABLE,		core99_firewire_enable },
-	{ PMAC_FTR_1394_CABLE_POWER,	core99_firewire_cable_power },
-	{ PMAC_FTR_SLEEP_STATE,		core99_sleep_state },
-#ifdef CONFIG_SMP
-	{ PMAC_FTR_RESET_CPU,		core99_reset_cpu },
-#endif /* CONFIG_SMP */
-	{ PMAC_FTR_READ_GPIO,		core99_read_gpio },
-	{ PMAC_FTR_WRITE_GPIO,		core99_write_gpio },
-	{ 0, NULL }
-};
-
-/* Pangea features
- */
-static struct feature_table_entry pangea_features[] = {
-	{ PMAC_FTR_SCC_ENABLE,		core99_scc_enable },
-	{ PMAC_FTR_MODEM_ENABLE,	pangea_modem_enable },
-	{ PMAC_FTR_IDE_ENABLE,		core99_ide_enable },
-	{ PMAC_FTR_IDE_RESET,		core99_ide_reset },
-	{ PMAC_FTR_GMAC_ENABLE,		core99_gmac_enable },
-	{ PMAC_FTR_GMAC_PHY_RESET,	core99_gmac_phy_reset },
-	{ PMAC_FTR_SOUND_CHIP_ENABLE,	core99_sound_chip_enable },
-	{ PMAC_FTR_AIRPORT_ENABLE,	core99_airport_enable },
-	{ PMAC_FTR_USB_ENABLE,		core99_usb_enable },
-	{ PMAC_FTR_1394_ENABLE,		core99_firewire_enable },
-	{ PMAC_FTR_1394_CABLE_POWER,	core99_firewire_cable_power },
-	{ PMAC_FTR_SLEEP_STATE,		core99_sleep_state },
-	{ PMAC_FTR_READ_GPIO,		core99_read_gpio },
-	{ PMAC_FTR_WRITE_GPIO,		core99_write_gpio },
-	{ 0, NULL }
-};
-
-/* Intrepid features
- */
-static struct feature_table_entry intrepid_features[] = {
-	{ PMAC_FTR_SCC_ENABLE,		core99_scc_enable },
-	{ PMAC_FTR_MODEM_ENABLE,	pangea_modem_enable },
-	{ PMAC_FTR_IDE_ENABLE,		core99_ide_enable },
-	{ PMAC_FTR_IDE_RESET,		core99_ide_reset },
-	{ PMAC_FTR_GMAC_ENABLE,		core99_gmac_enable },
-	{ PMAC_FTR_GMAC_PHY_RESET,	core99_gmac_phy_reset },
-	{ PMAC_FTR_SOUND_CHIP_ENABLE,	core99_sound_chip_enable },
-	{ PMAC_FTR_AIRPORT_ENABLE,	core99_airport_enable },
-	{ PMAC_FTR_USB_ENABLE,		core99_usb_enable },
-	{ PMAC_FTR_1394_ENABLE,		core99_firewire_enable },
-	{ PMAC_FTR_1394_CABLE_POWER,	core99_firewire_cable_power },
-	{ PMAC_FTR_SLEEP_STATE,		core99_sleep_state },
-	{ PMAC_FTR_READ_GPIO,		core99_read_gpio },
-	{ PMAC_FTR_WRITE_GPIO,		core99_write_gpio },
-	{ PMAC_FTR_AACK_DELAY_ENABLE,	intrepid_aack_delay_enable },
-	{ 0, NULL }
-};
-
-#else /* CONFIG_POWER4 */
-
-/* G5 features
- */
-static struct feature_table_entry g5_features[] = {
-	{ PMAC_FTR_GMAC_ENABLE,		g5_gmac_enable },
-	{ PMAC_FTR_1394_ENABLE,		g5_fw_enable },
-	{ PMAC_FTR_ENABLE_MPIC,		g5_mpic_enable },
-#ifdef CONFIG_SMP
-	{ PMAC_FTR_RESET_CPU,		g5_reset_cpu },
-#endif /* CONFIG_SMP */
-	{ PMAC_FTR_READ_GPIO,		core99_read_gpio },
-	{ PMAC_FTR_WRITE_GPIO,		core99_write_gpio },
-	{ 0, NULL }
-};
-
-#endif /* CONFIG_POWER4 */
-
-static struct pmac_mb_def pmac_mb_defs[] = {
-#ifndef CONFIG_POWER4
-	/*
-	 * Desktops
-	 */
-
-	{	"AAPL,8500",			"PowerMac 8500/8600",
-		PMAC_TYPE_PSURGE,		NULL,
-		0
-	},
-	{	"AAPL,9500",			"PowerMac 9500/9600",
-		PMAC_TYPE_PSURGE,		NULL,
-		0
-	},
-	{	"AAPL,7200",			"PowerMac 7200",
-		PMAC_TYPE_PSURGE,		NULL,
-		0
-	},
-	{	"AAPL,7300",			"PowerMac 7200/7300",
-		PMAC_TYPE_PSURGE,		NULL,
-		0
-	},
-	{	"AAPL,7500",			"PowerMac 7500",
-		PMAC_TYPE_PSURGE,		NULL,
-		0
-	},
-	{	"AAPL,ShinerESB",		"Apple Network Server",
-		PMAC_TYPE_ANS,			NULL,
-		0
-	},
-	{	"AAPL,e407",			"Alchemy",
-		PMAC_TYPE_ALCHEMY,		NULL,
-		0
-	},
-	{	"AAPL,e411",			"Gazelle",
-		PMAC_TYPE_GAZELLE,		NULL,
-		0
-	},
-	{	"AAPL,Gossamer",		"PowerMac G3 (Gossamer)",
-		PMAC_TYPE_GOSSAMER,		heathrow_desktop_features,
-		0
-	},
-	{	"AAPL,PowerMac G3",		"PowerMac G3 (Silk)",
-		PMAC_TYPE_SILK,			heathrow_desktop_features,
-		0
-	},
-	{	"PowerMac1,1",			"Blue&White G3",
-		PMAC_TYPE_YOSEMITE,		paddington_features,
-		0
-	},
-	{	"PowerMac1,2",			"PowerMac G4 PCI Graphics",
-		PMAC_TYPE_YIKES,		paddington_features,
-		0
-	},
-	{	"PowerMac2,1",			"iMac FireWire",
-		PMAC_TYPE_FW_IMAC,		core99_features,
-		PMAC_MB_MAY_SLEEP | PMAC_MB_OLD_CORE99
-	},
-	{	"PowerMac2,2",			"iMac FireWire",
-		PMAC_TYPE_FW_IMAC,		core99_features,
-		PMAC_MB_MAY_SLEEP | PMAC_MB_OLD_CORE99
-	},
-	{	"PowerMac3,1",			"PowerMac G4 AGP Graphics",
-		PMAC_TYPE_SAWTOOTH,		core99_features,
-		PMAC_MB_OLD_CORE99
-	},
-	{	"PowerMac3,2",			"PowerMac G4 AGP Graphics",
-		PMAC_TYPE_SAWTOOTH,		core99_features,
-		PMAC_MB_MAY_SLEEP | PMAC_MB_OLD_CORE99
-	},
-	{	"PowerMac3,3",			"PowerMac G4 AGP Graphics",
-		PMAC_TYPE_SAWTOOTH,		core99_features,
-		PMAC_MB_MAY_SLEEP | PMAC_MB_OLD_CORE99
-	},
-	{	"PowerMac3,4",			"PowerMac G4 Silver",
-		PMAC_TYPE_QUICKSILVER,		core99_features,
-		PMAC_MB_MAY_SLEEP
-	},
-	{	"PowerMac3,5",			"PowerMac G4 Silver",
-		PMAC_TYPE_QUICKSILVER,		core99_features,
-		PMAC_MB_MAY_SLEEP
-	},
-	{	"PowerMac3,6",			"PowerMac G4 Windtunnel",
-		PMAC_TYPE_WINDTUNNEL,		core99_features,
-		PMAC_MB_MAY_SLEEP,
-	},
-	{	"PowerMac4,1",			"iMac \"Flower Power\"",
-		PMAC_TYPE_PANGEA_IMAC,		pangea_features,
-		PMAC_MB_MAY_SLEEP
-	},
-	{	"PowerMac4,2",			"Flat panel iMac",
-		PMAC_TYPE_FLAT_PANEL_IMAC,	pangea_features,
-		PMAC_MB_CAN_SLEEP
-	},
-	{	"PowerMac4,4",			"eMac",
-		PMAC_TYPE_EMAC,			core99_features,
-		PMAC_MB_MAY_SLEEP
-	},
-	{	"PowerMac5,1",			"PowerMac G4 Cube",
-		PMAC_TYPE_CUBE,			core99_features,
-		PMAC_MB_MAY_SLEEP | PMAC_MB_OLD_CORE99
-	},
-	{	"PowerMac6,1",			"Flat panel iMac",
-		PMAC_TYPE_UNKNOWN_INTREPID,	intrepid_features,
-		PMAC_MB_MAY_SLEEP,
-	},
-	{	"PowerMac6,3",			"Flat panel iMac",
-		PMAC_TYPE_UNKNOWN_INTREPID,	intrepid_features,
-		PMAC_MB_MAY_SLEEP,
-	},
-	{	"PowerMac6,4",			"eMac",
-		PMAC_TYPE_UNKNOWN_INTREPID,	intrepid_features,
-		PMAC_MB_MAY_SLEEP,
-	},
-	{	"PowerMac10,1",			"Mac mini",
-		PMAC_TYPE_UNKNOWN_INTREPID,	intrepid_features,
-		PMAC_MB_MAY_SLEEP | PMAC_MB_HAS_FW_POWER,
-	},
-	{	"iMac,1",			"iMac (first generation)",
-		PMAC_TYPE_ORIG_IMAC,		paddington_features,
-		0
-	},
-
-	/*
-	 * Xserve's
-	 */
-
-	{	"RackMac1,1",			"XServe",
-		PMAC_TYPE_RACKMAC,		rackmac_features,
-		0,
-	},
-	{	"RackMac1,2",			"XServe rev. 2",
-		PMAC_TYPE_RACKMAC,		rackmac_features,
-		0,
-	},
-
-	/*
-	 * Laptops
-	 */
-
-	{	"AAPL,3400/2400",		"PowerBook 3400",
-		PMAC_TYPE_HOOPER,		ohare_features,
-		PMAC_MB_CAN_SLEEP | PMAC_MB_MOBILE
-	},
-	{	"AAPL,3500",			"PowerBook 3500",
-		PMAC_TYPE_KANGA,		ohare_features,
-		PMAC_MB_CAN_SLEEP | PMAC_MB_MOBILE
-	},
-	{	"AAPL,PowerBook1998",		"PowerBook Wallstreet",
-		PMAC_TYPE_WALLSTREET,		heathrow_laptop_features,
-		PMAC_MB_CAN_SLEEP | PMAC_MB_MOBILE
-	},
-	{	"PowerBook1,1",			"PowerBook 101 (Lombard)",
-		PMAC_TYPE_101_PBOOK,		paddington_features,
-		PMAC_MB_CAN_SLEEP | PMAC_MB_MOBILE
-	},
-	{	"PowerBook2,1",			"iBook (first generation)",
-		PMAC_TYPE_ORIG_IBOOK,		core99_features,
-		PMAC_MB_CAN_SLEEP | PMAC_MB_OLD_CORE99 | PMAC_MB_MOBILE
-	},
-	{	"PowerBook2,2",			"iBook FireWire",
-		PMAC_TYPE_FW_IBOOK,		core99_features,
-		PMAC_MB_MAY_SLEEP | PMAC_MB_HAS_FW_POWER |
-		PMAC_MB_OLD_CORE99 | PMAC_MB_MOBILE
-	},
-	{	"PowerBook3,1",			"PowerBook Pismo",
-		PMAC_TYPE_PISMO,		core99_features,
-		PMAC_MB_MAY_SLEEP | PMAC_MB_HAS_FW_POWER |
-		PMAC_MB_OLD_CORE99 | PMAC_MB_MOBILE
-	},
-	{	"PowerBook3,2",			"PowerBook Titanium",
-		PMAC_TYPE_TITANIUM,		core99_features,
-		PMAC_MB_MAY_SLEEP | PMAC_MB_HAS_FW_POWER | PMAC_MB_MOBILE
-	},
-	{	"PowerBook3,3",			"PowerBook Titanium II",
-		PMAC_TYPE_TITANIUM2,		core99_features,
-		PMAC_MB_MAY_SLEEP | PMAC_MB_HAS_FW_POWER | PMAC_MB_MOBILE
-	},
-	{	"PowerBook3,4",			"PowerBook Titanium III",
-		PMAC_TYPE_TITANIUM3,		core99_features,
-		PMAC_MB_MAY_SLEEP | PMAC_MB_HAS_FW_POWER | PMAC_MB_MOBILE
-	},
-	{	"PowerBook3,5",			"PowerBook Titanium IV",
-		PMAC_TYPE_TITANIUM4,		core99_features,
-		PMAC_MB_MAY_SLEEP | PMAC_MB_HAS_FW_POWER | PMAC_MB_MOBILE
-	},
-	{	"PowerBook4,1",			"iBook 2",
-		PMAC_TYPE_IBOOK2,		pangea_features,
-		PMAC_MB_MAY_SLEEP | PMAC_MB_HAS_FW_POWER | PMAC_MB_MOBILE
-	},
-	{	"PowerBook4,2",			"iBook 2",
-		PMAC_TYPE_IBOOK2,		pangea_features,
-		PMAC_MB_MAY_SLEEP | PMAC_MB_HAS_FW_POWER | PMAC_MB_MOBILE
-	},
-	{	"PowerBook4,3",			"iBook 2 rev. 2",
-		PMAC_TYPE_IBOOK2,		pangea_features,
-		PMAC_MB_MAY_SLEEP | PMAC_MB_HAS_FW_POWER | PMAC_MB_MOBILE
-	},
-	{	"PowerBook5,1",			"PowerBook G4 17\"",
-		PMAC_TYPE_UNKNOWN_INTREPID,	intrepid_features,
-		PMAC_MB_HAS_FW_POWER | PMAC_MB_MOBILE,
-	},
-	{	"PowerBook5,2",			"PowerBook G4 15\"",
-		PMAC_TYPE_UNKNOWN_INTREPID,	intrepid_features,
-		PMAC_MB_MAY_SLEEP | PMAC_MB_HAS_FW_POWER | PMAC_MB_MOBILE,
-	},
-	{	"PowerBook5,3",			"PowerBook G4 17\"",
-		PMAC_TYPE_UNKNOWN_INTREPID,	intrepid_features,
-		PMAC_MB_MAY_SLEEP | PMAC_MB_HAS_FW_POWER | PMAC_MB_MOBILE,
-	},
-	{	"PowerBook5,4",			"PowerBook G4 15\"",
-		PMAC_TYPE_UNKNOWN_INTREPID,	intrepid_features,
-		PMAC_MB_MAY_SLEEP | PMAC_MB_HAS_FW_POWER | PMAC_MB_MOBILE,
-	},
-	{	"PowerBook5,5",			"PowerBook G4 17\"",
-		PMAC_TYPE_UNKNOWN_INTREPID,	intrepid_features,
-		PMAC_MB_MAY_SLEEP | PMAC_MB_HAS_FW_POWER | PMAC_MB_MOBILE,
-	},
-	{	"PowerBook5,6",			"PowerBook G4 15\"",
-		PMAC_TYPE_UNKNOWN_INTREPID,	intrepid_features,
-		PMAC_MB_MAY_SLEEP | PMAC_MB_HAS_FW_POWER | PMAC_MB_MOBILE,
-	},
-	{	"PowerBook5,7",			"PowerBook G4 17\"",
-		PMAC_TYPE_UNKNOWN_INTREPID,	intrepid_features,
-		PMAC_MB_MAY_SLEEP | PMAC_MB_HAS_FW_POWER | PMAC_MB_MOBILE,
-	},
-	{	"PowerBook5,8",			"PowerBook G4 15\"",
-		PMAC_TYPE_UNKNOWN_INTREPID,	intrepid_features,
-		PMAC_MB_MAY_SLEEP | PMAC_MB_HAS_FW_POWER | PMAC_MB_MOBILE,
-	},
-	{	"PowerBook5,9",			"PowerBook G4 17\"",
-		PMAC_TYPE_UNKNOWN_INTREPID,	intrepid_features,
-		PMAC_MB_MAY_SLEEP | PMAC_MB_HAS_FW_POWER | PMAC_MB_MOBILE,
-	},
-	{	"PowerBook6,1",			"PowerBook G4 12\"",
-		PMAC_TYPE_UNKNOWN_INTREPID,	intrepid_features,
-		PMAC_MB_MAY_SLEEP | PMAC_MB_HAS_FW_POWER | PMAC_MB_MOBILE,
-	},
-	{	"PowerBook6,2",			"PowerBook G4",
-		PMAC_TYPE_UNKNOWN_INTREPID,	intrepid_features,
-		PMAC_MB_MAY_SLEEP | PMAC_MB_HAS_FW_POWER | PMAC_MB_MOBILE,
-	},
-	{	"PowerBook6,3",			"iBook G4",
-		PMAC_TYPE_UNKNOWN_INTREPID,	intrepid_features,
-		PMAC_MB_MAY_SLEEP | PMAC_MB_HAS_FW_POWER | PMAC_MB_MOBILE,
-	},
-	{	"PowerBook6,4",			"PowerBook G4 12\"",
-		PMAC_TYPE_UNKNOWN_INTREPID,	intrepid_features,
-		PMAC_MB_MAY_SLEEP | PMAC_MB_HAS_FW_POWER | PMAC_MB_MOBILE,
-	},
-	{	"PowerBook6,5",			"iBook G4",
-		PMAC_TYPE_UNKNOWN_INTREPID,	intrepid_features,
-		PMAC_MB_MAY_SLEEP | PMAC_MB_HAS_FW_POWER | PMAC_MB_MOBILE,
-	},
-	{	"PowerBook6,7",			"iBook G4",
-		PMAC_TYPE_UNKNOWN_INTREPID,	intrepid_features,
-		PMAC_MB_MAY_SLEEP | PMAC_MB_HAS_FW_POWER | PMAC_MB_MOBILE,
-	},
-	{	"PowerBook6,8",			"PowerBook G4 12\"",
-		PMAC_TYPE_UNKNOWN_INTREPID,	intrepid_features,
-		PMAC_MB_MAY_SLEEP | PMAC_MB_HAS_FW_POWER | PMAC_MB_MOBILE,
-	},
-#else /* CONFIG_POWER4 */
-	{	"PowerMac7,2",			"PowerMac G5",
-		PMAC_TYPE_POWERMAC_G5,		g5_features,
-		0,
-	},
-#endif /* CONFIG_POWER4 */
-};
-
-/*
- * The toplevel feature_call callback
- */
-long
-pmac_do_feature_call(unsigned int selector, ...)
-{
-	struct device_node* node;
-	long param, value;
-	int i;
-	feature_call func = NULL;
-	va_list args;
-
-	if (pmac_mb.features)
-		for (i=0; pmac_mb.features[i].function; i++)
-			if (pmac_mb.features[i].selector == selector) {
-				func = pmac_mb.features[i].function;
-				break;
-			}
-	if (!func)
-		for (i=0; any_features[i].function; i++)
-			if (any_features[i].selector == selector) {
-				func = any_features[i].function;
-				break;
-			}
-	if (!func)
-		return -ENODEV;
-
-	va_start(args, selector);
-	node = (struct device_node*)va_arg(args, void*);
-	param = va_arg(args, long);
-	value = va_arg(args, long);
-	va_end(args);
-
-	return func(node, param, value);
-}
-
-static int __init
-probe_motherboard(void)
-{
-	int i;
-	struct macio_chip* macio = &macio_chips[0];
-	const char* model = NULL;
-	struct device_node *dt;
-
-	/* Lookup known motherboard type in device-tree. First try an
-	 * exact match on the "model" property, then try a "compatible"
-	 * match is none is found.
-	 */
-	dt = find_devices("device-tree");
-	if (dt != NULL)
-		model = (const char *) get_property(dt, "model", NULL);
-	for(i=0; model && i<(sizeof(pmac_mb_defs)/sizeof(struct pmac_mb_def)); i++) {
-	    if (strcmp(model, pmac_mb_defs[i].model_string) == 0) {
-		pmac_mb = pmac_mb_defs[i];
-		goto found;
-	    }
-	}
-	for(i=0; i<(sizeof(pmac_mb_defs)/sizeof(struct pmac_mb_def)); i++) {
-	    if (machine_is_compatible(pmac_mb_defs[i].model_string)) {
-		pmac_mb = pmac_mb_defs[i];
-		goto found;
-	    }
-	}
-
-	/* Fallback to selection depending on mac-io chip type */
-	switch(macio->type) {
-#ifndef CONFIG_POWER4
-	    case macio_grand_central:
-		pmac_mb.model_id = PMAC_TYPE_PSURGE;
-		pmac_mb.model_name = "Unknown PowerSurge";
-		break;
-	    case macio_ohare:
-		pmac_mb.model_id = PMAC_TYPE_UNKNOWN_OHARE;
-		pmac_mb.model_name = "Unknown OHare-based";
-	    	break;
-	    case macio_heathrow:
-		pmac_mb.model_id = PMAC_TYPE_UNKNOWN_HEATHROW;
-		pmac_mb.model_name = "Unknown Heathrow-based";
-		pmac_mb.features = heathrow_desktop_features;
-		break;
-	    case macio_paddington:
-		pmac_mb.model_id = PMAC_TYPE_UNKNOWN_PADDINGTON;
-		pmac_mb.model_name = "Unknown Paddington-based";
-	    	pmac_mb.features = paddington_features;
-		break;
-	    case macio_keylargo:
-		pmac_mb.model_id = PMAC_TYPE_UNKNOWN_CORE99;
-		pmac_mb.model_name = "Unknown Keylargo-based";
-	    	pmac_mb.features = core99_features;
-		break;
-	    case macio_pangea:
-		pmac_mb.model_id = PMAC_TYPE_UNKNOWN_PANGEA;
-		pmac_mb.model_name = "Unknown Pangea-based";
-	    	pmac_mb.features = pangea_features;
-		break;
-	    case macio_intrepid:
-		pmac_mb.model_id = PMAC_TYPE_UNKNOWN_INTREPID;
-		pmac_mb.model_name = "Unknown Intrepid-based";
-	    	pmac_mb.features = intrepid_features;
-	    	break;
-#else /* CONFIG_POWER4 */
-	    case macio_keylargo2:
-		pmac_mb.model_id = PMAC_TYPE_UNKNOWN_K2;
-		pmac_mb.model_name = "Unknown G5";
-	    	pmac_mb.features = g5_features;
-	    	break;
-#endif /* CONFIG_POWER4 */
-	    default:
-	    	return -ENODEV;
-	}
-found:
-#ifndef CONFIG_POWER4
-	/* Fixup Hooper vs. Comet */
-	if (pmac_mb.model_id == PMAC_TYPE_HOOPER) {
-		u32 __iomem * mach_id_ptr = ioremap(0xf3000034, 4);
-		if (!mach_id_ptr)
-			return -ENODEV;
-		/* Here, I used to disable the media-bay on comet. It
-		 * appears this is wrong, the floppy connector is actually
-		 * a kind of media-bay and works with the current driver.
-		 */
-		if (__raw_readl(mach_id_ptr) & 0x20000000UL)
-			pmac_mb.model_id = PMAC_TYPE_COMET;
-		iounmap(mach_id_ptr);
-	}
-#endif /* CONFIG_POWER4 */
-
-#ifdef CONFIG_6xx
-	/* Set default value of powersave_nap on machines that support it.
-	 * It appears that uninorth rev 3 has a problem with it, we don't
-	 * enable it on those. In theory, the flush-on-lock property is
-	 * supposed to be set when not supported, but I'm not very confident
-	 * that all Apple OF revs did it properly, I do it the paranoid way.
-	 */
-	while (uninorth_base && uninorth_rev > 3) {
-		struct device_node* np = find_path_device("/cpus");
-		if (!np || !np->child) {
-			printk(KERN_WARNING "Can't find CPU(s) in device tree !\n");
-			break;
-		}
-		np = np->child;
-		/* Nap mode not supported on SMP */
-		if (np->sibling)
-			break;
-		/* Nap mode not supported if flush-on-lock property is present */
-		if (get_property(np, "flush-on-lock", NULL))
-			break;
-		powersave_nap = 1;
-		printk(KERN_INFO "Processor NAP mode on idle enabled.\n");
-		break;
-	}
-
-	/* On CPUs that support it (750FX), lowspeed by default during
-	 * NAP mode
-	 */
-	powersave_lowspeed = 1;
-#endif /* CONFIG_6xx */
-#ifdef CONFIG_POWER4
-	powersave_nap = 1;
-#endif
-	/* Check for "mobile" machine */
-	if (model && (strncmp(model, "PowerBook", 9) == 0
-		   || strncmp(model, "iBook", 5) == 0))
-		pmac_mb.board_flags |= PMAC_MB_MOBILE;
-
-
-	printk(KERN_INFO "PowerMac motherboard: %s\n", pmac_mb.model_name);
-	return 0;
-}
-
-/* Initialize the Core99 UniNorth host bridge and memory controller
- */
-static void __init
-probe_uninorth(void)
-{
-	unsigned long actrl;
-
-	/* Locate core99 Uni-N */
-	uninorth_node = of_find_node_by_name(NULL, "uni-n");
-	/* Locate G5 u3 */
-	if (uninorth_node == NULL) {
-		uninorth_node = of_find_node_by_name(NULL, "u3");
-		uninorth_u3 = 1;
-	}
-	if (uninorth_node && uninorth_node->n_addrs > 0) {
-		unsigned long address = uninorth_node->addrs[0].address;
-		uninorth_base = ioremap(address, 0x40000);
-		uninorth_rev = in_be32(UN_REG(UNI_N_VERSION));
-		if (uninorth_u3)
-			u3_ht = ioremap(address + U3_HT_CONFIG_BASE, 0x1000);
-	} else
-		uninorth_node = NULL;
-
-	if (!uninorth_node)
-		return;
-
-	printk(KERN_INFO "Found %s memory controller & host bridge, revision: %d\n",
-	       uninorth_u3 ? "U3" : "UniNorth", uninorth_rev);
-	printk(KERN_INFO "Mapped at 0x%08lx\n", (unsigned long)uninorth_base);
-
-	/* Set the arbitrer QAck delay according to what Apple does
-	 */
-	if (uninorth_rev < 0x11) {
-		actrl = UN_IN(UNI_N_ARB_CTRL) & ~UNI_N_ARB_CTRL_QACK_DELAY_MASK;
-		actrl |= ((uninorth_rev < 3) ? UNI_N_ARB_CTRL_QACK_DELAY105 :
-			UNI_N_ARB_CTRL_QACK_DELAY) << UNI_N_ARB_CTRL_QACK_DELAY_SHIFT;
-		UN_OUT(UNI_N_ARB_CTRL, actrl);
-	}
-
-	/* Some more magic as done by them in recent MacOS X on UniNorth
-	 * revs 1.5 to 2.O and Pangea. Seem to toggle the UniN Maxbus/PCI
-	 * memory timeout
-	 */
-	if ((uninorth_rev >= 0x11 && uninorth_rev <= 0x24) || uninorth_rev == 0xc0)
-		UN_OUT(0x2160, UN_IN(0x2160) & 0x00ffffff);
-}
-
-static void __init
-probe_one_macio(const char* name, const char* compat, int type)
-{
-	struct device_node*	node;
-	int			i;
-	volatile u32 __iomem *	base;
-	u32*			revp;
-
-	node = find_devices(name);
-	if (!node || !node->n_addrs)
-		return;
-	if (compat)
-		do {
-			if (device_is_compatible(node, compat))
-				break;
-			node = node->next;
-		} while (node);
-	if (!node)
-		return;
-	for(i=0; i<MAX_MACIO_CHIPS; i++) {
-		if (!macio_chips[i].of_node)
-			break;
-		if (macio_chips[i].of_node == node)
-			return;
-	}
-	if (i >= MAX_MACIO_CHIPS) {
-		printk(KERN_ERR "pmac_feature: Please increase MAX_MACIO_CHIPS !\n");
-		printk(KERN_ERR "pmac_feature: %s skipped\n", node->full_name);
-		return;
-	}
-	base = ioremap(node->addrs[0].address, node->addrs[0].size);
-	if (!base) {
-		printk(KERN_ERR "pmac_feature: Can't map mac-io chip !\n");
-		return;
-	}
-	if (type == macio_keylargo) {
-		u32* did = (u32 *)get_property(node, "device-id", NULL);
-		if (*did == 0x00000025)
-			type = macio_pangea;
-		if (*did == 0x0000003e)
-			type = macio_intrepid;
-	}
-	macio_chips[i].of_node	= node;
-	macio_chips[i].type	= type;
-	macio_chips[i].base	= base;
-	macio_chips[i].flags	= MACIO_FLAG_SCCB_ON | MACIO_FLAG_SCCB_ON;
-	macio_chips[i].name 	= macio_names[type];
-	revp = (u32 *)get_property(node, "revision-id", NULL);
-	if (revp)
-		macio_chips[i].rev = *revp;
-	printk(KERN_INFO "Found a %s mac-io controller, rev: %d, mapped at 0x%p\n",
-		macio_names[type], macio_chips[i].rev, macio_chips[i].base);
-}
-
-static int __init
-probe_macios(void)
-{
-	/* Warning, ordering is important */
-	probe_one_macio("gc", NULL, macio_grand_central);
-	probe_one_macio("ohare", NULL, macio_ohare);
-	probe_one_macio("pci106b,7", NULL, macio_ohareII);
-	probe_one_macio("mac-io", "keylargo", macio_keylargo);
-	probe_one_macio("mac-io", "paddington", macio_paddington);
-	probe_one_macio("mac-io", "gatwick", macio_gatwick);
-	probe_one_macio("mac-io", "heathrow", macio_heathrow);
-	probe_one_macio("mac-io", "K2-Keylargo", macio_keylargo2);
-
-	/* Make sure the "main" macio chip appear first */
-	if (macio_chips[0].type == macio_gatwick
-	    && macio_chips[1].type == macio_heathrow) {
-		struct macio_chip temp = macio_chips[0];
-		macio_chips[0] = macio_chips[1];
-		macio_chips[1] = temp;
-	}
-	if (macio_chips[0].type == macio_ohareII
-	    && macio_chips[1].type == macio_ohare) {
-		struct macio_chip temp = macio_chips[0];
-		macio_chips[0] = macio_chips[1];
-		macio_chips[1] = temp;
-	}
-	macio_chips[0].lbus.index = 0;
-	macio_chips[1].lbus.index = 1;
-
-	return (macio_chips[0].of_node == NULL) ? -ENODEV : 0;
-}
-
-static void __init
-initial_serial_shutdown(struct device_node* np)
-{
-	int len;
-	struct slot_names_prop {
-		int	count;
-		char	name[1];
-	} *slots;
-	char *conn;
-	int port_type = PMAC_SCC_ASYNC;
-	int modem = 0;
-
-	slots = (struct slot_names_prop *)get_property(np, "slot-names", &len);
-	conn = get_property(np, "AAPL,connector", &len);
-	if (conn && (strcmp(conn, "infrared") == 0))
-		port_type = PMAC_SCC_IRDA;
-	else if (device_is_compatible(np, "cobalt"))
-		modem = 1;
-	else if (slots && slots->count > 0) {
-		if (strcmp(slots->name, "IrDA") == 0)
-			port_type = PMAC_SCC_IRDA;
-		else if (strcmp(slots->name, "Modem") == 0)
-			modem = 1;
-	}
-	if (modem)
-		pmac_call_feature(PMAC_FTR_MODEM_ENABLE, np, 0, 0);
-	pmac_call_feature(PMAC_FTR_SCC_ENABLE, np, port_type, 0);
-}
-
-static void __init
-set_initial_features(void)
-{
-	struct device_node* np;
-
-	/* That hack appears to be necessary for some StarMax motherboards
-	 * but I'm not too sure it was audited for side-effects on other
-	 * ohare based machines...
-	 * Since I still have difficulties figuring the right way to
-	 * differenciate them all and since that hack was there for a long
-	 * time, I'll keep it around
-	 */
-	if (macio_chips[0].type == macio_ohare && !find_devices("via-pmu")) {
-		struct macio_chip* macio = &macio_chips[0];
-		MACIO_OUT32(OHARE_FCR, STARMAX_FEATURES);
-	} else if (macio_chips[0].type == macio_ohare) {
-		struct macio_chip* macio = &macio_chips[0];
-		MACIO_BIS(OHARE_FCR, OH_IOBUS_ENABLE);
-	} else if (macio_chips[1].type == macio_ohare) {
-		struct macio_chip* macio = &macio_chips[1];
-		MACIO_BIS(OHARE_FCR, OH_IOBUS_ENABLE);
-	}
-
-#ifdef CONFIG_POWER4
-	if (macio_chips[0].type == macio_keylargo2) {
-#ifndef CONFIG_SMP
-		/* On SMP machines running UP, we have the second CPU eating
-		 * bus cycles. We need to take it off the bus. This is done
-		 * from pmac_smp for SMP kernels running on one CPU
-		 */
-		np = of_find_node_by_type(NULL, "cpu");
-		if (np != NULL)
-			np = of_find_node_by_type(np, "cpu");
-		if (np != NULL) {
-			g5_phy_disable_cpu1();
-			of_node_put(np);
-		}
-#endif /* CONFIG_SMP */
-		/* Enable GMAC for now for PCI probing. It will be disabled
-		 * later on after PCI probe
-		 */
-		np = of_find_node_by_name(NULL, "ethernet");
-		while(np) {
-			if (device_is_compatible(np, "K2-GMAC"))
-				g5_gmac_enable(np, 0, 1);
-			np = of_find_node_by_name(np, "ethernet");
-		}
-
-		/* Enable FW before PCI probe. Will be disabled later on
-		 * Note: We should have a batter way to check that we are
-		 * dealing with uninorth internal cell and not a PCI cell
-		 * on the external PCI. The code below works though.
-		 */
-		np = of_find_node_by_name(NULL, "firewire");
-		while(np) {
-			if (device_is_compatible(np, "pci106b,5811")) {
-				macio_chips[0].flags |= MACIO_FLAG_FW_SUPPORTED;
-				g5_fw_enable(np, 0, 1);
-			}
-			np = of_find_node_by_name(np, "firewire");
-		}
-	}
-#else /* CONFIG_POWER4 */
-
-	if (macio_chips[0].type == macio_keylargo ||
-	    macio_chips[0].type == macio_pangea ||
-	    macio_chips[0].type == macio_intrepid) {
-		/* Enable GMAC for now for PCI probing. It will be disabled
-		 * later on after PCI probe
-		 */
-		np = of_find_node_by_name(NULL, "ethernet");
-		while(np) {
-			if (np->parent
-			    && device_is_compatible(np->parent, "uni-north")
-			    && device_is_compatible(np, "gmac"))
-				core99_gmac_enable(np, 0, 1);
-			np = of_find_node_by_name(np, "ethernet");
-		}
-
-		/* Enable FW before PCI probe. Will be disabled later on
-		 * Note: We should have a batter way to check that we are
-		 * dealing with uninorth internal cell and not a PCI cell
-		 * on the external PCI. The code below works though.
-		 */
-		np = of_find_node_by_name(NULL, "firewire");
-		while(np) {
-			if (np->parent
-			    && device_is_compatible(np->parent, "uni-north")
-			    && (device_is_compatible(np, "pci106b,18") ||
-	     		        device_is_compatible(np, "pci106b,30") ||
-	     		        device_is_compatible(np, "pci11c1,5811"))) {
-				macio_chips[0].flags |= MACIO_FLAG_FW_SUPPORTED;
-				core99_firewire_enable(np, 0, 1);
-			}
-			np = of_find_node_by_name(np, "firewire");
-		}
-
-		/* Enable ATA-100 before PCI probe. */
-		np = of_find_node_by_name(NULL, "ata-6");
-		while(np) {
-			if (np->parent
-			    && device_is_compatible(np->parent, "uni-north")
-			    && device_is_compatible(np, "kauai-ata")) {
-				core99_ata100_enable(np, 1);
-			}
-			np = of_find_node_by_name(np, "ata-6");
-		}
-
-		/* Switch airport off */
-		np = find_devices("radio");
-		while(np) {
-			if (np && np->parent == macio_chips[0].of_node) {
-				macio_chips[0].flags |= MACIO_FLAG_AIRPORT_ON;
-				core99_airport_enable(np, 0, 0);
-			}
-			np = np->next;
-		}
-	}
-
-	/* On all machines that support sound PM, switch sound off */
-	if (macio_chips[0].of_node)
-		pmac_do_feature_call(PMAC_FTR_SOUND_CHIP_ENABLE,
-			macio_chips[0].of_node, 0, 0);
-
-	/* While on some desktop G3s, we turn it back on */
-	if (macio_chips[0].of_node && macio_chips[0].type == macio_heathrow
-		&& (pmac_mb.model_id == PMAC_TYPE_GOSSAMER ||
-		    pmac_mb.model_id == PMAC_TYPE_SILK)) {
-		struct macio_chip* macio = &macio_chips[0];
-		MACIO_BIS(HEATHROW_FCR, HRW_SOUND_CLK_ENABLE);
-		MACIO_BIC(HEATHROW_FCR, HRW_SOUND_POWER_N);
-	}
-
-	/* Some machine models need the clock chip to be properly setup for
-	 * clock spreading now. This should be a platform function but we
-	 * don't do these at the moment
-	 */
-	pmac_tweak_clock_spreading(1);
-
-#endif /* CONFIG_POWER4 */
-
-	/* On all machines, switch modem & serial ports off */
-	np = find_devices("ch-a");
-	while(np) {
-		initial_serial_shutdown(np);
-		np = np->next;
-	}
-	np = find_devices("ch-b");
-	while(np) {
-		initial_serial_shutdown(np);
-		np = np->next;
-	}
-}
-
-void __init
-pmac_feature_init(void)
-{
-	/* Detect the UniNorth memory controller */
-	probe_uninorth();
-
-	/* Probe mac-io controllers */
-	if (probe_macios()) {
-		printk(KERN_WARNING "No mac-io chip found\n");
-		return;
-	}
-
-	/* Setup low-level i2c stuffs */
-	pmac_init_low_i2c();
-
-	/* Probe machine type */
-	if (probe_motherboard())
-		printk(KERN_WARNING "Unknown PowerMac !\n");
-
-	/* Set some initial features (turn off some chips that will
-	 * be later turned on)
-	 */
-	set_initial_features();
-}
-
-int __init
-pmac_feature_late_init(void)
-{
-	struct device_node* np;
-
-	/* Request some resources late */
-	if (uninorth_node)
-		request_OF_resource(uninorth_node, 0, NULL);
-	np = find_devices("hammerhead");
-	if (np)
-		request_OF_resource(np, 0, NULL);
-	np = find_devices("interrupt-controller");
-	if (np)
-		request_OF_resource(np, 0, NULL);
-	return 0;
-}
-
-device_initcall(pmac_feature_late_init);
-
-#ifdef CONFIG_POWER4
-
-static void dump_HT_speeds(char *name, u32 cfg, u32 frq)
-{
-	int	freqs[16] = { 200,300,400,500,600,800,1000,0,0,0,0,0,0,0,0,0 };
-	int	bits[8] = { 8,16,0,32,2,4,0,0 };
-	int	freq = (frq >> 8) & 0xf;
-
-	if (freqs[freq] == 0)
-		printk("%s: Unknown HT link frequency %x\n", name, freq);
-	else
-		printk("%s: %d MHz on main link, (%d in / %d out) bits width\n",
-		       name, freqs[freq],
-		       bits[(cfg >> 28) & 0x7], bits[(cfg >> 24) & 0x7]);
-}
-
-void __init pmac_check_ht_link(void)
-{
-	u32	ufreq, freq, ucfg, cfg;
-	struct device_node *pcix_node;
-	u8  	px_bus, px_devfn;
-	struct pci_controller *px_hose;
-
-	(void)in_be32(u3_ht + U3_HT_LINK_COMMAND);
-	ucfg = cfg = in_be32(u3_ht + U3_HT_LINK_CONFIG);
-	ufreq = freq = in_be32(u3_ht + U3_HT_LINK_FREQ);
-	dump_HT_speeds("U3 HyperTransport", cfg, freq);
-
-	pcix_node = of_find_compatible_node(NULL, "pci", "pci-x");
-	if (pcix_node == NULL) {
-		printk("No PCI-X bridge found\n");
-		return;
-	}
-	if (pci_device_from_OF_node(pcix_node, &px_bus, &px_devfn) != 0) {
-		printk("PCI-X bridge found but not matched to pci\n");
-		return;
-	}
-	px_hose = pci_find_hose_for_OF_device(pcix_node);
-	if (px_hose == NULL) {
-		printk("PCI-X bridge found but not matched to host\n");
-		return;
-	}	
-	early_read_config_dword(px_hose, px_bus, px_devfn, 0xc4, &cfg);
-	early_read_config_dword(px_hose, px_bus, px_devfn, 0xcc, &freq);
-	dump_HT_speeds("PCI-X HT Uplink", cfg, freq);
-	early_read_config_dword(px_hose, px_bus, px_devfn, 0xc8, &cfg);
-	early_read_config_dword(px_hose, px_bus, px_devfn, 0xd0, &freq);
-	dump_HT_speeds("PCI-X HT Downlink", cfg, freq);
-}
-
-#endif /* CONFIG_POWER4 */
-
-/*
- * Early video resume hook
- */
-
-static void (*pmac_early_vresume_proc)(void *data);
-static void *pmac_early_vresume_data;
-
-void pmac_set_early_video_resume(void (*proc)(void *data), void *data)
-{
-	if (_machine != _MACH_Pmac)
-		return;
-	preempt_disable();
-	pmac_early_vresume_proc = proc;
-	pmac_early_vresume_data = data;
-	preempt_enable();
-}
-EXPORT_SYMBOL(pmac_set_early_video_resume);
-
-void pmac_call_early_video_resume(void)
-{
-	if (pmac_early_vresume_proc)
-		pmac_early_vresume_proc(pmac_early_vresume_data);
-}
-
-/*
- * AGP related suspend/resume code
- */
-
-static struct pci_dev *pmac_agp_bridge;
-static int (*pmac_agp_suspend)(struct pci_dev *bridge);
-static int (*pmac_agp_resume)(struct pci_dev *bridge);
-
-void pmac_register_agp_pm(struct pci_dev *bridge,
-				 int (*suspend)(struct pci_dev *bridge),
-				 int (*resume)(struct pci_dev *bridge))
-{
-	if (suspend || resume) {
-		pmac_agp_bridge = bridge;
-		pmac_agp_suspend = suspend;
-		pmac_agp_resume = resume;
-		return;
-	}
-	if (bridge != pmac_agp_bridge)
-		return;
-	pmac_agp_suspend = pmac_agp_resume = NULL;
-	return;
-}
-EXPORT_SYMBOL(pmac_register_agp_pm);
-
-void pmac_suspend_agp_for_card(struct pci_dev *dev)
-{
-	if (pmac_agp_bridge == NULL || pmac_agp_suspend == NULL)
-		return;
-	if (pmac_agp_bridge->bus != dev->bus)
-		return;
-	pmac_agp_suspend(pmac_agp_bridge);
-}
-EXPORT_SYMBOL(pmac_suspend_agp_for_card);
-
-void pmac_resume_agp_for_card(struct pci_dev *dev)
-{
-	if (pmac_agp_bridge == NULL || pmac_agp_resume == NULL)
-		return;
-	if (pmac_agp_bridge->bus != dev->bus)
-		return;
-	pmac_agp_resume(pmac_agp_bridge);
-}
-EXPORT_SYMBOL(pmac_resume_agp_for_card);
diff --git a/arch/ppc/platforms/pmac_low_i2c.c b/arch/ppc/platforms/pmac_low_i2c.c
deleted file mode 100644
index 08583fce169..00000000000
--- a/arch/ppc/platforms/pmac_low_i2c.c
+++ /dev/null
@@ -1,511 +0,0 @@
-/*
- *  arch/ppc/platforms/pmac_low_i2c.c
- *
- *  Copyright (C) 2003 Ben. Herrenschmidt (benh@kernel.crashing.org)
- *
- *  This program is free software; you can redistribute it and/or
- *  modify it under the terms of the GNU General Public License
- *  as published by the Free Software Foundation; either version
- *  2 of the License, or (at your option) any later version.
- *
- *  This file contains some low-level i2c access routines that
- *  need to be used by various bits of the PowerMac platform code
- *  at times where the real asynchronous & interrupt driven driver
- *  cannot be used. The API borrows some semantics from the darwin
- *  driver in order to ease the implementation of the platform
- *  properties parser
- */
-
-#include <linux/config.h>
-#include <linux/types.h>
-#include <linux/delay.h>
-#include <linux/sched.h>
-#include <linux/init.h>
-#include <linux/module.h>
-#include <linux/adb.h>
-#include <linux/pmu.h>
-#include <asm/keylargo.h>
-#include <asm/uninorth.h>
-#include <asm/io.h>
-#include <asm/prom.h>
-#include <asm/machdep.h>
-#include <asm/pmac_low_i2c.h>
-
-#define MAX_LOW_I2C_HOST	4
-
-#if 1
-#define DBG(x...) do {\
-		printk(KERN_DEBUG "KW:" x);	\
-	} while(0)
-#else
-#define DBGG(x...)
-#endif
-
-struct low_i2c_host;
-
-typedef int (*low_i2c_func_t)(struct low_i2c_host *host, u8 addr, u8 sub, u8 *data, int len);
-
-struct low_i2c_host
-{
-	struct device_node	*np;		/* OF device node */
-	struct semaphore	mutex;		/* Access mutex for use by i2c-keywest */
-	low_i2c_func_t		func;		/* Access function */
-	int			is_open : 1;	/* Poor man's access control */
-	int			mode;		/* Current mode */
-	int			channel;	/* Current channel */
-	int			num_channels;	/* Number of channels */
-	void __iomem *		base;		/* For keywest-i2c, base address */
-	int			bsteps;		/* And register stepping */
-	int			speed;		/* And speed */
-};
-
-static struct low_i2c_host	low_i2c_hosts[MAX_LOW_I2C_HOST];
-
-/* No locking is necessary on allocation, we are running way before
- * anything can race with us
- */
-static struct low_i2c_host *find_low_i2c_host(struct device_node *np)
-{
-	int i;
-
-	for (i = 0; i < MAX_LOW_I2C_HOST; i++)
-		if (low_i2c_hosts[i].np == np)
-			return &low_i2c_hosts[i];
-	return NULL;
-}
-
-/*
- *
- * i2c-keywest implementation (UniNorth, U2, U3, Keylargo's)
- *
- */
-
-/*
- * Keywest i2c definitions borrowed from drivers/i2c/i2c-keywest.h,
- * should be moved somewhere in include/asm-ppc/
- */
-/* Register indices */
-typedef enum {
-	reg_mode = 0,
-	reg_control,
-	reg_status,
-	reg_isr,
-	reg_ier,
-	reg_addr,
-	reg_subaddr,
-	reg_data
-} reg_t;
-
-
-/* Mode register */
-#define KW_I2C_MODE_100KHZ	0x00
-#define KW_I2C_MODE_50KHZ	0x01
-#define KW_I2C_MODE_25KHZ	0x02
-#define KW_I2C_MODE_DUMB	0x00
-#define KW_I2C_MODE_STANDARD	0x04
-#define KW_I2C_MODE_STANDARDSUB	0x08
-#define KW_I2C_MODE_COMBINED	0x0C
-#define KW_I2C_MODE_MODE_MASK	0x0C
-#define KW_I2C_MODE_CHAN_MASK	0xF0
-
-/* Control register */
-#define KW_I2C_CTL_AAK		0x01
-#define KW_I2C_CTL_XADDR	0x02
-#define KW_I2C_CTL_STOP		0x04
-#define KW_I2C_CTL_START	0x08
-
-/* Status register */
-#define KW_I2C_STAT_BUSY	0x01
-#define KW_I2C_STAT_LAST_AAK	0x02
-#define KW_I2C_STAT_LAST_RW	0x04
-#define KW_I2C_STAT_SDA		0x08
-#define KW_I2C_STAT_SCL		0x10
-
-/* IER & ISR registers */
-#define KW_I2C_IRQ_DATA		0x01
-#define KW_I2C_IRQ_ADDR		0x02
-#define KW_I2C_IRQ_STOP		0x04
-#define KW_I2C_IRQ_START	0x08
-#define KW_I2C_IRQ_MASK		0x0F
-
-/* State machine states */
-enum {
-	state_idle,
-	state_addr,
-	state_read,
-	state_write,
-	state_stop,
-	state_dead
-};
-
-#define WRONG_STATE(name) do {\
-		printk(KERN_DEBUG "KW: wrong state. Got %s, state: %s (isr: %02x)\n", \
-		       name, __kw_state_names[state], isr); \
-	} while(0)
-
-static const char *__kw_state_names[] = {
-	"state_idle",
-	"state_addr",
-	"state_read",
-	"state_write",
-	"state_stop",
-	"state_dead"
-};
-
-static inline u8 __kw_read_reg(struct low_i2c_host *host, reg_t reg)
-{
-	return in_8(host->base + (((unsigned)reg) << host->bsteps));
-}
-
-static inline void __kw_write_reg(struct low_i2c_host *host, reg_t reg, u8 val)
-{
-	out_8(host->base + (((unsigned)reg) << host->bsteps), val);
-	(void)__kw_read_reg(host, reg_subaddr);
-}
-
-#define kw_write_reg(reg, val)	__kw_write_reg(host, reg, val) 
-#define kw_read_reg(reg)	__kw_read_reg(host, reg) 
-
-
-/* Don't schedule, the g5 fan controller is too
- * timing sensitive
- */
-static u8 kw_wait_interrupt(struct low_i2c_host* host)
-{
-	int i;
-	u8 isr;
-	
-	for (i = 0; i < 200000; i++) {
-		isr = kw_read_reg(reg_isr) & KW_I2C_IRQ_MASK;
-		if (isr != 0)
-			return isr;
-		udelay(1);
-	}
-	return isr;
-}
-
-static int kw_handle_interrupt(struct low_i2c_host *host, int state, int rw, int *rc, u8 **data, int *len, u8 isr)
-{
-	u8 ack;
-
-	if (isr == 0) {
-		if (state != state_stop) {
-			DBG("KW: Timeout !\n");
-			*rc = -EIO;
-			goto stop;
-		}
-		if (state == state_stop) {
-			ack = kw_read_reg(reg_status);
-			if (!(ack & KW_I2C_STAT_BUSY)) {
-				state = state_idle;
-				kw_write_reg(reg_ier, 0x00);
-			}
-		}
-		return state;
-	}
-
-	if (isr & KW_I2C_IRQ_ADDR) {
-		ack = kw_read_reg(reg_status);
-		if (state != state_addr) {
-			kw_write_reg(reg_isr, KW_I2C_IRQ_ADDR);
-			WRONG_STATE("KW_I2C_IRQ_ADDR"); 
-			*rc = -EIO;
-			goto stop;
-		}
-		if ((ack & KW_I2C_STAT_LAST_AAK) == 0) {			
-			*rc = -ENODEV;
-			DBG("KW: NAK on address\n");
-			return state_stop;		     
-		} else {
-			if (rw) {
-				state = state_read;
-				if (*len > 1)
-					kw_write_reg(reg_control, KW_I2C_CTL_AAK);
-			} else {
-				state = state_write;
-				kw_write_reg(reg_data, **data);
-				(*data)++; (*len)--;
-			}
-		}
-		kw_write_reg(reg_isr, KW_I2C_IRQ_ADDR);
-	}
-
-	if (isr & KW_I2C_IRQ_DATA) {
-		if (state == state_read) {
-			**data = kw_read_reg(reg_data);
-			(*data)++; (*len)--;
-			kw_write_reg(reg_isr, KW_I2C_IRQ_DATA);
-			if ((*len) == 0)
-				state = state_stop;
-			else if ((*len) == 1)
-				kw_write_reg(reg_control, 0);
-		} else if (state == state_write) {
-			ack = kw_read_reg(reg_status);
-			if ((ack & KW_I2C_STAT_LAST_AAK) == 0) {
-				DBG("KW: nack on data write\n");
-				*rc = -EIO;
-				goto stop;
-			} else if (*len) {
-				kw_write_reg(reg_data, **data);
-				(*data)++; (*len)--;
-			} else {
-				kw_write_reg(reg_control, KW_I2C_CTL_STOP);
-				state = state_stop;
-				*rc = 0;
-			}
-			kw_write_reg(reg_isr, KW_I2C_IRQ_DATA);
-		} else {
-			kw_write_reg(reg_isr, KW_I2C_IRQ_DATA);
-			WRONG_STATE("KW_I2C_IRQ_DATA"); 
-			if (state != state_stop) {
-				*rc = -EIO;
-				goto stop;
-			}
-		}
-	}
-
-	if (isr & KW_I2C_IRQ_STOP) {
-		kw_write_reg(reg_isr, KW_I2C_IRQ_STOP);
-		if (state != state_stop) {
-			WRONG_STATE("KW_I2C_IRQ_STOP");
-			*rc = -EIO;
-		}
-		return state_idle;
-	}
-
-	if (isr & KW_I2C_IRQ_START)
-		kw_write_reg(reg_isr, KW_I2C_IRQ_START);
-
-	return state;
-
- stop:
-	kw_write_reg(reg_control, KW_I2C_CTL_STOP);	
-	return state_stop;
-}
-
-static int keywest_low_i2c_func(struct low_i2c_host *host, u8 addr, u8 subaddr, u8 *data, int len)
-{
-	u8 mode_reg = host->speed;
-	int state = state_addr;
-	int rc = 0;
-
-	/* Setup mode & subaddress if any */
-	switch(host->mode) {
-	case pmac_low_i2c_mode_dumb:
-		printk(KERN_ERR "low_i2c: Dumb mode not supported !\n");
-		return -EINVAL;
-	case pmac_low_i2c_mode_std:
-		mode_reg |= KW_I2C_MODE_STANDARD;
-		break;
-	case pmac_low_i2c_mode_stdsub:
-		mode_reg |= KW_I2C_MODE_STANDARDSUB;
-		kw_write_reg(reg_subaddr, subaddr);
-		break;
-	case pmac_low_i2c_mode_combined:
-		mode_reg |= KW_I2C_MODE_COMBINED;
-		kw_write_reg(reg_subaddr, subaddr);
-		break;
-	}
-
-	/* Setup channel & clear pending irqs */
-	kw_write_reg(reg_isr, kw_read_reg(reg_isr));
-	kw_write_reg(reg_mode, mode_reg | (host->channel << 4));
-	kw_write_reg(reg_status, 0);
-
-	/* Set up address and r/w bit */
-	kw_write_reg(reg_addr, addr);
-
-	/* Start sending address & disable interrupt*/
-	kw_write_reg(reg_ier, 0 /*KW_I2C_IRQ_MASK*/);
-	kw_write_reg(reg_control, KW_I2C_CTL_XADDR);
-
-	/* State machine, to turn into an interrupt handler */
-	while(state != state_idle) {
-		u8 isr = kw_wait_interrupt(host);
-		state = kw_handle_interrupt(host, state, addr & 1, &rc, &data, &len, isr);
-	}
-
-	return rc;
-}
-
-static void keywest_low_i2c_add(struct device_node *np)
-{
-	struct low_i2c_host	*host = find_low_i2c_host(NULL);
-	unsigned long		*psteps, *prate, steps, aoffset = 0;
-	struct device_node	*parent;
-
-	if (host == NULL) {
-		printk(KERN_ERR "low_i2c: Can't allocate host for %s\n",
-		       np->full_name);
-		return;
-	}
-	memset(host, 0, sizeof(*host));
-
-	init_MUTEX(&host->mutex);
-	host->np = of_node_get(np);	
-	psteps = (unsigned long *)get_property(np, "AAPL,address-step", NULL);
-	steps = psteps ? (*psteps) : 0x10;
-	for (host->bsteps = 0; (steps & 0x01) == 0; host->bsteps++)
-		steps >>= 1;
-	parent = of_get_parent(np);
-	host->num_channels = 1;
-	if (parent && parent->name[0] == 'u') {
-		host->num_channels = 2;
-		aoffset = 3;
-	}
-	/* Select interface rate */
-	host->speed = KW_I2C_MODE_100KHZ;
-	prate = (unsigned long *)get_property(np, "AAPL,i2c-rate", NULL);
-	if (prate) switch(*prate) {
-	case 100:
-		host->speed = KW_I2C_MODE_100KHZ;
-		break;
-	case 50:
-		host->speed = KW_I2C_MODE_50KHZ;
-		break;
-	case 25:
-		host->speed = KW_I2C_MODE_25KHZ;
-		break;
-	}	
-	host->mode = pmac_low_i2c_mode_std;
-	host->base = ioremap(np->addrs[0].address + aoffset,
-						np->addrs[0].size);
-	host->func = keywest_low_i2c_func;
-}
-
-/*
- *
- * PMU implementation
- *
- */
-
-
-#ifdef CONFIG_ADB_PMU
-
-static int pmu_low_i2c_func(struct low_i2c_host *host, u8 addr, u8 sub, u8 *data, int len)
-{
-	// TODO
-	return -ENODEV;
-}
-
-static void pmu_low_i2c_add(struct device_node *np)
-{
-	struct low_i2c_host	*host = find_low_i2c_host(NULL);
-
-	if (host == NULL) {
-		printk(KERN_ERR "low_i2c: Can't allocate host for %s\n",
-		       np->full_name);
-		return;
-	}
-	memset(host, 0, sizeof(*host));
-
-	init_MUTEX(&host->mutex);
-	host->np = of_node_get(np);	
-	host->num_channels = 3;
-	host->mode = pmac_low_i2c_mode_std;
-	host->func = pmu_low_i2c_func;
-}
-
-#endif /* CONFIG_ADB_PMU */
-
-void __init pmac_init_low_i2c(void)
-{
-	struct device_node *np;
-
-	/* Probe keywest-i2c busses */
-	np = of_find_compatible_node(NULL, "i2c", "keywest-i2c");
-	while(np) {
-		keywest_low_i2c_add(np);
-		np = of_find_compatible_node(np, "i2c", "keywest-i2c");
-	}
-
-#ifdef CONFIG_ADB_PMU
-	/* Probe PMU busses */
-	np = of_find_node_by_name(NULL, "via-pmu");
-	if (np)
-		pmu_low_i2c_add(np);
-#endif /* CONFIG_ADB_PMU */
-
-	/* TODO: Add CUDA support as well */
-}
-
-int pmac_low_i2c_lock(struct device_node *np)
-{
-	struct low_i2c_host *host = find_low_i2c_host(np);
-
-	if (!host)
-		return -ENODEV;
-	down(&host->mutex);
-	return 0;
-}
-EXPORT_SYMBOL(pmac_low_i2c_lock);
-
-int pmac_low_i2c_unlock(struct device_node *np)
-{
-	struct low_i2c_host *host = find_low_i2c_host(np);
-
-	if (!host)
-		return -ENODEV;
-	up(&host->mutex);
-	return 0;
-}
-EXPORT_SYMBOL(pmac_low_i2c_unlock);
-
-
-int pmac_low_i2c_open(struct device_node *np, int channel)
-{
-	struct low_i2c_host *host = find_low_i2c_host(np);
-
-	if (!host)
-		return -ENODEV;
-
-	if (channel >= host->num_channels)
-		return -EINVAL;
-
-	down(&host->mutex);
-	host->is_open = 1;
-	host->channel = channel;
-
-	return 0;
-}
-EXPORT_SYMBOL(pmac_low_i2c_open);
-
-int pmac_low_i2c_close(struct device_node *np)
-{
-	struct low_i2c_host *host = find_low_i2c_host(np);
-
-	if (!host)
-		return -ENODEV;
-
-	host->is_open = 0;
-	up(&host->mutex);
-
-	return 0;
-}
-EXPORT_SYMBOL(pmac_low_i2c_close);
-
-int pmac_low_i2c_setmode(struct device_node *np, int mode)
-{
-	struct low_i2c_host *host = find_low_i2c_host(np);
-
-	if (!host)
-		return -ENODEV;
-	WARN_ON(!host->is_open);
-	host->mode = mode;
-
-	return 0;
-}
-EXPORT_SYMBOL(pmac_low_i2c_setmode);
-
-int pmac_low_i2c_xfer(struct device_node *np, u8 addrdir, u8 subaddr, u8 *data, int len)
-{
-	struct low_i2c_host *host = find_low_i2c_host(np);
-
-	if (!host)
-		return -ENODEV;
-	WARN_ON(!host->is_open);
-
-	return host->func(host, addrdir, subaddr, data, len);
-}
-EXPORT_SYMBOL(pmac_low_i2c_xfer);
-
diff --git a/arch/ppc/platforms/pmac_nvram.c b/arch/ppc/platforms/pmac_nvram.c
deleted file mode 100644
index 8c9b008c722..00000000000
--- a/arch/ppc/platforms/pmac_nvram.c
+++ /dev/null
@@ -1,584 +0,0 @@
-/*
- *  arch/ppc/platforms/pmac_nvram.c
- *
- *  Copyright (C) 2002 Benjamin Herrenschmidt (benh@kernel.crashing.org)
- *
- *  This program is free software; you can redistribute it and/or
- *  modify it under the terms of the GNU General Public License
- *  as published by the Free Software Foundation; either version
- *  2 of the License, or (at your option) any later version.
- *
- *  Todo: - add support for the OF persistent properties
- */
-#include <linux/config.h>
-#include <linux/module.h>
-#include <linux/kernel.h>
-#include <linux/stddef.h>
-#include <linux/string.h>
-#include <linux/nvram.h>
-#include <linux/init.h>
-#include <linux/slab.h>
-#include <linux/delay.h>
-#include <linux/errno.h>
-#include <linux/adb.h>
-#include <linux/pmu.h>
-#include <linux/bootmem.h>
-#include <linux/completion.h>
-#include <linux/spinlock.h>
-#include <asm/sections.h>
-#include <asm/io.h>
-#include <asm/system.h>
-#include <asm/prom.h>
-#include <asm/machdep.h>
-#include <asm/nvram.h>
-
-#define DEBUG
-
-#ifdef DEBUG
-#define DBG(x...) printk(x)
-#else
-#define DBG(x...)
-#endif
-
-#define NVRAM_SIZE		0x2000	/* 8kB of non-volatile RAM */
-
-#define CORE99_SIGNATURE	0x5a
-#define CORE99_ADLER_START	0x14
-
-/* On Core99, nvram is either a sharp, a micron or an AMD flash */
-#define SM_FLASH_STATUS_DONE	0x80
-#define SM_FLASH_STATUS_ERR		0x38
-#define SM_FLASH_CMD_ERASE_CONFIRM	0xd0
-#define SM_FLASH_CMD_ERASE_SETUP	0x20
-#define SM_FLASH_CMD_RESET		0xff
-#define SM_FLASH_CMD_WRITE_SETUP	0x40
-#define SM_FLASH_CMD_CLEAR_STATUS	0x50
-#define SM_FLASH_CMD_READ_STATUS	0x70
-
-/* CHRP NVRAM header */
-struct chrp_header {
-  u8		signature;
-  u8		cksum;
-  u16		len;
-  char          name[12];
-  u8		data[0];
-};
-
-struct core99_header {
-  struct chrp_header	hdr;
-  u32			adler;
-  u32			generation;
-  u32			reserved[2];
-};
-
-/*
- * Read and write the non-volatile RAM on PowerMacs and CHRP machines.
- */
-static int nvram_naddrs;
-static volatile unsigned char *nvram_addr;
-static volatile unsigned char *nvram_data;
-static int nvram_mult, is_core_99;
-static int core99_bank = 0;
-static int nvram_partitions[3];
-static DEFINE_SPINLOCK(nv_lock);
-
-extern int pmac_newworld;
-extern int system_running;
-
-static int (*core99_write_bank)(int bank, u8* datas);
-static int (*core99_erase_bank)(int bank);
-
-static char *nvram_image;
-
-
-static unsigned char core99_nvram_read_byte(int addr)
-{
-	if (nvram_image == NULL)
-		return 0xff;
-	return nvram_image[addr];
-}
-
-static void core99_nvram_write_byte(int addr, unsigned char val)
-{
-	if (nvram_image == NULL)
-		return;
-	nvram_image[addr] = val;
-}
-
-
-static unsigned char direct_nvram_read_byte(int addr)
-{
-	return in_8(&nvram_data[(addr & (NVRAM_SIZE - 1)) * nvram_mult]);
-}
-
-static void direct_nvram_write_byte(int addr, unsigned char val)
-{
-	out_8(&nvram_data[(addr & (NVRAM_SIZE - 1)) * nvram_mult], val);
-}
-
-
-static unsigned char indirect_nvram_read_byte(int addr)
-{
-	unsigned char val;
-	unsigned long flags;
-
-	spin_lock_irqsave(&nv_lock, flags);
-	out_8(nvram_addr, addr >> 5);
-	val = in_8(&nvram_data[(addr & 0x1f) << 4]);
-	spin_unlock_irqrestore(&nv_lock, flags);
-
-	return val;
-}
-
-static void indirect_nvram_write_byte(int addr, unsigned char val)
-{
-	unsigned long flags;
-
-	spin_lock_irqsave(&nv_lock, flags);
-	out_8(nvram_addr, addr >> 5);
-	out_8(&nvram_data[(addr & 0x1f) << 4], val);
-	spin_unlock_irqrestore(&nv_lock, flags);
-}
-
-
-#ifdef CONFIG_ADB_PMU
-
-static void pmu_nvram_complete(struct adb_request *req)
-{
-	if (req->arg)
-		complete((struct completion *)req->arg);
-}
-
-static unsigned char pmu_nvram_read_byte(int addr)
-{
-	struct adb_request req;
-	DECLARE_COMPLETION(req_complete); 
-	
-	req.arg = system_state == SYSTEM_RUNNING ? &req_complete : NULL;
-	if (pmu_request(&req, pmu_nvram_complete, 3, PMU_READ_NVRAM,
-			(addr >> 8) & 0xff, addr & 0xff))
-		return 0xff;
-	if (system_state == SYSTEM_RUNNING)
-		wait_for_completion(&req_complete);
-	while (!req.complete)
-		pmu_poll();
-	return req.reply[0];
-}
-
-static void pmu_nvram_write_byte(int addr, unsigned char val)
-{
-	struct adb_request req;
-	DECLARE_COMPLETION(req_complete); 
-	
-	req.arg = system_state == SYSTEM_RUNNING ? &req_complete : NULL;
-	if (pmu_request(&req, pmu_nvram_complete, 4, PMU_WRITE_NVRAM,
-			(addr >> 8) & 0xff, addr & 0xff, val))
-		return;
-	if (system_state == SYSTEM_RUNNING)
-		wait_for_completion(&req_complete);
-	while (!req.complete)
-		pmu_poll();
-}
-
-#endif /* CONFIG_ADB_PMU */
-
-
-static u8 chrp_checksum(struct chrp_header* hdr)
-{
-	u8 *ptr;
-	u16 sum = hdr->signature;
-	for (ptr = (u8 *)&hdr->len; ptr < hdr->data; ptr++)
-		sum += *ptr;
-	while (sum > 0xFF)
-		sum = (sum & 0xFF) + (sum>>8);
-	return sum;
-}
-
-static u32 core99_calc_adler(u8 *buffer)
-{
-	int cnt;
-	u32 low, high;
-
-   	buffer += CORE99_ADLER_START;
-	low = 1;
-	high = 0;
-	for (cnt=0; cnt<(NVRAM_SIZE-CORE99_ADLER_START); cnt++) {
-		if ((cnt % 5000) == 0) {
-			high  %= 65521UL;
-			high %= 65521UL;
-		}
-		low += buffer[cnt];
-		high += low;
-	}
-	low  %= 65521UL;
-	high %= 65521UL;
-
-	return (high << 16) | low;
-}
-
-static u32 core99_check(u8* datas)
-{
-	struct core99_header* hdr99 = (struct core99_header*)datas;
-
-	if (hdr99->hdr.signature != CORE99_SIGNATURE) {
-		DBG("Invalid signature\n");
-		return 0;
-	}
-	if (hdr99->hdr.cksum != chrp_checksum(&hdr99->hdr)) {
-		DBG("Invalid checksum\n");
-		return 0;
-	}
-	if (hdr99->adler != core99_calc_adler(datas)) {
-		DBG("Invalid adler\n");
-		return 0;
-	}
-	return hdr99->generation;
-}
-
-static int sm_erase_bank(int bank)
-{
-	int stat, i;
-	unsigned long timeout;
-
-	u8* base = (u8 *)nvram_data + core99_bank*NVRAM_SIZE;
-
-       	DBG("nvram: Sharp/Micron Erasing bank %d...\n", bank);
-
-	out_8(base, SM_FLASH_CMD_ERASE_SETUP);
-	out_8(base, SM_FLASH_CMD_ERASE_CONFIRM);
-	timeout = 0;
-	do {
-		if (++timeout > 1000000) {
-			printk(KERN_ERR "nvram: Sharp/Miron flash erase timeout !\n");
-			break;
-		}
-		out_8(base, SM_FLASH_CMD_READ_STATUS);
-		stat = in_8(base);
-	} while (!(stat & SM_FLASH_STATUS_DONE));
-
-	out_8(base, SM_FLASH_CMD_CLEAR_STATUS);
-	out_8(base, SM_FLASH_CMD_RESET);
-
-	for (i=0; i<NVRAM_SIZE; i++)
-		if (base[i] != 0xff) {
-			printk(KERN_ERR "nvram: Sharp/Micron flash erase failed !\n");
-			return -ENXIO;
-		}
-	return 0;
-}
-
-static int sm_write_bank(int bank, u8* datas)
-{
-	int i, stat = 0;
-	unsigned long timeout;
-
-	u8* base = (u8 *)nvram_data + core99_bank*NVRAM_SIZE;
-
-       	DBG("nvram: Sharp/Micron Writing bank %d...\n", bank);
-
-	for (i=0; i<NVRAM_SIZE; i++) {
-		out_8(base+i, SM_FLASH_CMD_WRITE_SETUP);
-		udelay(1);
-		out_8(base+i, datas[i]);
-		timeout = 0;
-		do {
-			if (++timeout > 1000000) {
-				printk(KERN_ERR "nvram: Sharp/Micron flash write timeout !\n");
-				break;
-			}
-			out_8(base, SM_FLASH_CMD_READ_STATUS);
-			stat = in_8(base);
-		} while (!(stat & SM_FLASH_STATUS_DONE));
-		if (!(stat & SM_FLASH_STATUS_DONE))
-			break;
-	}
-	out_8(base, SM_FLASH_CMD_CLEAR_STATUS);
-	out_8(base, SM_FLASH_CMD_RESET);
-	for (i=0; i<NVRAM_SIZE; i++)
-		if (base[i] != datas[i]) {
-			printk(KERN_ERR "nvram: Sharp/Micron flash write failed !\n");
-			return -ENXIO;
-		}
-	return 0;
-}
-
-static int amd_erase_bank(int bank)
-{
-	int i, stat = 0;
-	unsigned long timeout;
-
-	u8* base = (u8 *)nvram_data + core99_bank*NVRAM_SIZE;
-
-       	DBG("nvram: AMD Erasing bank %d...\n", bank);
-
-	/* Unlock 1 */
-	out_8(base+0x555, 0xaa);
-	udelay(1);
-	/* Unlock 2 */
-	out_8(base+0x2aa, 0x55);
-	udelay(1);
-
-	/* Sector-Erase */
-	out_8(base+0x555, 0x80);
-	udelay(1);
-	out_8(base+0x555, 0xaa);
-	udelay(1);
-	out_8(base+0x2aa, 0x55);
-	udelay(1);
-	out_8(base, 0x30);
-	udelay(1);
-
-	timeout = 0;
-	do {
-		if (++timeout > 1000000) {
-			printk(KERN_ERR "nvram: AMD flash erase timeout !\n");
-			break;
-		}
-		stat = in_8(base) ^ in_8(base);
-	} while (stat != 0);
-	
-	/* Reset */
-	out_8(base, 0xf0);
-	udelay(1);
-	
-	for (i=0; i<NVRAM_SIZE; i++)
-		if (base[i] != 0xff) {
-			printk(KERN_ERR "nvram: AMD flash erase failed !\n");
-			return -ENXIO;
-		}
-	return 0;
-}
-
-static int amd_write_bank(int bank, u8* datas)
-{
-	int i, stat = 0;
-	unsigned long timeout;
-
-	u8* base = (u8 *)nvram_data + core99_bank*NVRAM_SIZE;
-
-       	DBG("nvram: AMD Writing bank %d...\n", bank);
-
-	for (i=0; i<NVRAM_SIZE; i++) {
-		/* Unlock 1 */
-		out_8(base+0x555, 0xaa);
-		udelay(1);
-		/* Unlock 2 */
-		out_8(base+0x2aa, 0x55);
-		udelay(1);
-
-		/* Write single word */
-		out_8(base+0x555, 0xa0);
-		udelay(1);
-		out_8(base+i, datas[i]);
-		
-		timeout = 0;
-		do {
-			if (++timeout > 1000000) {
-				printk(KERN_ERR "nvram: AMD flash write timeout !\n");
-				break;
-			}
-			stat = in_8(base) ^ in_8(base);
-		} while (stat != 0);
-		if (stat != 0)
-			break;
-	}
-
-	/* Reset */
-	out_8(base, 0xf0);
-	udelay(1);
-
-	for (i=0; i<NVRAM_SIZE; i++)
-		if (base[i] != datas[i]) {
-			printk(KERN_ERR "nvram: AMD flash write failed !\n");
-			return -ENXIO;
-		}
-	return 0;
-}
-
-static void __init lookup_partitions(void)
-{
-	u8 buffer[17];
-	int i, offset;
-	struct chrp_header* hdr;
-
-	if (pmac_newworld) {
-		nvram_partitions[pmac_nvram_OF] = -1;
-		nvram_partitions[pmac_nvram_XPRAM] = -1;
-		nvram_partitions[pmac_nvram_NR] = -1;
-		hdr = (struct chrp_header *)buffer;
-
-		offset = 0;
-		buffer[16] = 0;
-		do {
-			for (i=0;i<16;i++)
-				buffer[i] = nvram_read_byte(offset+i);
-			if (!strcmp(hdr->name, "common"))
-				nvram_partitions[pmac_nvram_OF] = offset + 0x10;
-			if (!strcmp(hdr->name, "APL,MacOS75")) {
-				nvram_partitions[pmac_nvram_XPRAM] = offset + 0x10;
-				nvram_partitions[pmac_nvram_NR] = offset + 0x110;
-			}
-			offset += (hdr->len * 0x10);
-		} while(offset < NVRAM_SIZE);
-	} else {
-		nvram_partitions[pmac_nvram_OF] = 0x1800;
-		nvram_partitions[pmac_nvram_XPRAM] = 0x1300;
-		nvram_partitions[pmac_nvram_NR] = 0x1400;
-	}
-	DBG("nvram: OF partition at 0x%x\n", nvram_partitions[pmac_nvram_OF]);
-	DBG("nvram: XP partition at 0x%x\n", nvram_partitions[pmac_nvram_XPRAM]);
-	DBG("nvram: NR partition at 0x%x\n", nvram_partitions[pmac_nvram_NR]);
-}
-
-static void core99_nvram_sync(void)
-{
-	struct core99_header* hdr99;
-	unsigned long flags;
-
-	if (!is_core_99 || !nvram_data || !nvram_image)
-		return;
-
-	spin_lock_irqsave(&nv_lock, flags);
-	if (!memcmp(nvram_image, (u8*)nvram_data + core99_bank*NVRAM_SIZE,
-		NVRAM_SIZE))
-		goto bail;
-
-	DBG("Updating nvram...\n");
-
-	hdr99 = (struct core99_header*)nvram_image;
-	hdr99->generation++;
-	hdr99->hdr.signature = CORE99_SIGNATURE;
-	hdr99->hdr.cksum = chrp_checksum(&hdr99->hdr);
-	hdr99->adler = core99_calc_adler(nvram_image);
-	core99_bank = core99_bank ? 0 : 1;
-	if (core99_erase_bank)
-		if (core99_erase_bank(core99_bank)) {
-			printk("nvram: Error erasing bank %d\n", core99_bank);
-			goto bail;
-		}
-	if (core99_write_bank)
-		if (core99_write_bank(core99_bank, nvram_image))
-			printk("nvram: Error writing bank %d\n", core99_bank);
- bail:
-	spin_unlock_irqrestore(&nv_lock, flags);
-
-#ifdef DEBUG
-       	mdelay(2000);
-#endif
-}
-
-void __init pmac_nvram_init(void)
-{
-	struct device_node *dp;
-
-	nvram_naddrs = 0;
-
-	dp = find_devices("nvram");
-	if (dp == NULL) {
-		printk(KERN_ERR "Can't find NVRAM device\n");
-		return;
-	}
-	nvram_naddrs = dp->n_addrs;
-	is_core_99 = device_is_compatible(dp, "nvram,flash");
-	if (is_core_99) {
-		int i;
-		u32 gen_bank0, gen_bank1;
-
-		if (nvram_naddrs < 1) {
-			printk(KERN_ERR "nvram: no address\n");
-			return;
-		}
-		nvram_image = alloc_bootmem(NVRAM_SIZE);
-		if (nvram_image == NULL) {
-			printk(KERN_ERR "nvram: can't allocate ram image\n");
-			return;
-		}
-		nvram_data = ioremap(dp->addrs[0].address, NVRAM_SIZE*2);
-		nvram_naddrs = 1; /* Make sure we get the correct case */
-
-		DBG("nvram: Checking bank 0...\n");
-
-		gen_bank0 = core99_check((u8 *)nvram_data);
-		gen_bank1 = core99_check((u8 *)nvram_data + NVRAM_SIZE);
-		core99_bank = (gen_bank0 < gen_bank1) ? 1 : 0;
-
-		DBG("nvram: gen0=%d, gen1=%d\n", gen_bank0, gen_bank1);
-		DBG("nvram: Active bank is: %d\n", core99_bank);
-
-		for (i=0; i<NVRAM_SIZE; i++)
-			nvram_image[i] = nvram_data[i + core99_bank*NVRAM_SIZE];
-
-		ppc_md.nvram_read_val	= core99_nvram_read_byte;
-		ppc_md.nvram_write_val	= core99_nvram_write_byte;
-		ppc_md.nvram_sync	= core99_nvram_sync;
-		/* 
-		 * Maybe we could be smarter here though making an exclusive list
-		 * of known flash chips is a bit nasty as older OF didn't provide us
-		 * with a useful "compatible" entry. A solution would be to really
-		 * identify the chip using flash id commands and base ourselves on
-		 * a list of known chips IDs
-		 */
-		if (device_is_compatible(dp, "amd-0137")) {
-			core99_erase_bank = amd_erase_bank;
-			core99_write_bank = amd_write_bank;
-		} else {
-			core99_erase_bank = sm_erase_bank;
-			core99_write_bank = sm_write_bank;
-		}
-	} else if (_machine == _MACH_chrp && nvram_naddrs == 1) {
-		nvram_data = ioremap(dp->addrs[0].address + isa_mem_base,
-				     dp->addrs[0].size);
-		nvram_mult = 1;
-		ppc_md.nvram_read_val	= direct_nvram_read_byte;
-		ppc_md.nvram_write_val	= direct_nvram_write_byte;
-	} else if (nvram_naddrs == 1) {
-		nvram_data = ioremap(dp->addrs[0].address, dp->addrs[0].size);
-		nvram_mult = (dp->addrs[0].size + NVRAM_SIZE - 1) / NVRAM_SIZE;
-		ppc_md.nvram_read_val	= direct_nvram_read_byte;
-		ppc_md.nvram_write_val	= direct_nvram_write_byte;
-	} else if (nvram_naddrs == 2) {
-		nvram_addr = ioremap(dp->addrs[0].address, dp->addrs[0].size);
-		nvram_data = ioremap(dp->addrs[1].address, dp->addrs[1].size);
-		ppc_md.nvram_read_val	= indirect_nvram_read_byte;
-		ppc_md.nvram_write_val	= indirect_nvram_write_byte;
-	} else if (nvram_naddrs == 0 && sys_ctrler == SYS_CTRLER_PMU) {
-#ifdef CONFIG_ADB_PMU
-		nvram_naddrs = -1;
-		ppc_md.nvram_read_val	= pmu_nvram_read_byte;
-		ppc_md.nvram_write_val	= pmu_nvram_write_byte;
-#endif /* CONFIG_ADB_PMU */
-	} else {
-		printk(KERN_ERR "Don't know how to access NVRAM with %d addresses\n",
-		       nvram_naddrs);
-	}
-	lookup_partitions();
-}
-
-int pmac_get_partition(int partition)
-{
-	return nvram_partitions[partition];
-}
-
-u8 pmac_xpram_read(int xpaddr)
-{
-	int offset = nvram_partitions[pmac_nvram_XPRAM];
-
-	if (offset < 0)
-		return 0xff;
-
-	return ppc_md.nvram_read_val(xpaddr + offset);
-}
-
-void pmac_xpram_write(int xpaddr, u8 data)
-{
-	int offset = nvram_partitions[pmac_nvram_XPRAM];
-
-	if (offset < 0)
-		return;
-
-	ppc_md.nvram_write_val(xpaddr + offset, data);
-}
-
-EXPORT_SYMBOL(pmac_get_partition);
-EXPORT_SYMBOL(pmac_xpram_read);
-EXPORT_SYMBOL(pmac_xpram_write);
diff --git a/arch/ppc/platforms/pmac_pci.c b/arch/ppc/platforms/pmac_pci.c
deleted file mode 100644
index 786295b6ddd..00000000000
--- a/arch/ppc/platforms/pmac_pci.c
+++ /dev/null
@@ -1,1124 +0,0 @@
-/*
- * Support for PCI bridges found on Power Macintoshes.
- * At present the "bandit" and "chaos" bridges are supported.
- * Fortunately you access configuration space in the same
- * way with either bridge.
- *
- * Copyright (C) 1997 Paul Mackerras (paulus@cs.anu.edu.au)
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License
- * as published by the Free Software Foundation; either version
- * 2 of the License, or (at your option) any later version.
- */
-
-#include <linux/kernel.h>
-#include <linux/pci.h>
-#include <linux/delay.h>
-#include <linux/string.h>
-#include <linux/init.h>
-
-#include <asm/sections.h>
-#include <asm/io.h>
-#include <asm/prom.h>
-#include <asm/pci-bridge.h>
-#include <asm/machdep.h>
-#include <asm/pmac_feature.h>
-
-#undef DEBUG
-
-#ifdef DEBUG
-#ifdef CONFIG_XMON
-extern void xmon_printf(const char *fmt, ...);
-#define DBG(x...) xmon_printf(x)
-#else
-#define DBG(x...) printk(x)
-#endif
-#else
-#define DBG(x...)
-#endif
-
-static int add_bridge(struct device_node *dev);
-extern void pmac_check_ht_link(void);
-
-/* XXX Could be per-controller, but I don't think we risk anything by
- * assuming we won't have both UniNorth and Bandit */
-static int has_uninorth;
-#ifdef CONFIG_POWER4
-static struct pci_controller *u3_agp;
-#endif /* CONFIG_POWER4 */
-
-extern u8 pci_cache_line_size;
-extern int pcibios_assign_bus_offset;
-
-struct device_node *k2_skiplist[2];
-
-/*
- * Magic constants for enabling cache coherency in the bandit/PSX bridge.
- */
-#define BANDIT_DEVID_2	8
-#define BANDIT_REVID	3
-
-#define BANDIT_DEVNUM	11
-#define BANDIT_MAGIC	0x50
-#define BANDIT_COHERENT	0x40
-
-static int __init
-fixup_one_level_bus_range(struct device_node *node, int higher)
-{
-	for (; node != 0;node = node->sibling) {
-		int * bus_range;
-		unsigned int *class_code;
-		int len;
-
-		/* For PCI<->PCI bridges or CardBus bridges, we go down */
-		class_code = (unsigned int *) get_property(node, "class-code", NULL);
-		if (!class_code || ((*class_code >> 8) != PCI_CLASS_BRIDGE_PCI &&
-			(*class_code >> 8) != PCI_CLASS_BRIDGE_CARDBUS))
-			continue;
-		bus_range = (int *) get_property(node, "bus-range", &len);
-		if (bus_range != NULL && len > 2 * sizeof(int)) {
-			if (bus_range[1] > higher)
-				higher = bus_range[1];
-		}
-		higher = fixup_one_level_bus_range(node->child, higher);
-	}
-	return higher;
-}
-
-/* This routine fixes the "bus-range" property of all bridges in the
- * system since they tend to have their "last" member wrong on macs
- *
- * Note that the bus numbers manipulated here are OF bus numbers, they
- * are not Linux bus numbers.
- */
-static void __init
-fixup_bus_range(struct device_node *bridge)
-{
-	int * bus_range;
-	int len;
-
-	/* Lookup the "bus-range" property for the hose */
-	bus_range = (int *) get_property(bridge, "bus-range", &len);
-	if (bus_range == NULL || len < 2 * sizeof(int)) {
-		printk(KERN_WARNING "Can't get bus-range for %s\n",
-			       bridge->full_name);
-		return;
-	}
-	bus_range[1] = fixup_one_level_bus_range(bridge->child, bus_range[1]);
-}
-
-/*
- * Apple MacRISC (U3, UniNorth, Bandit, Chaos) PCI controllers.
- *
- * The "Bandit" version is present in all early PCI PowerMacs,
- * and up to the first ones using Grackle. Some machines may
- * have 2 bandit controllers (2 PCI busses).
- *
- * "Chaos" is used in some "Bandit"-type machines as a bridge
- * for the separate display bus. It is accessed the same
- * way as bandit, but cannot be probed for devices. It therefore
- * has its own config access functions.
- *
- * The "UniNorth" version is present in all Core99 machines
- * (iBook, G4, new IMacs, and all the recent Apple machines).
- * It contains 3 controllers in one ASIC.
- *
- * The U3 is the bridge used on G5 machines. It contains an
- * AGP bus which is dealt with the old UniNorth access routines
- * and a HyperTransport bus which uses its own set of access
- * functions.
- */
-
-#define MACRISC_CFA0(devfn, off)	\
-	((1 << (unsigned long)PCI_SLOT(dev_fn)) \
-	| (((unsigned long)PCI_FUNC(dev_fn)) << 8) \
-	| (((unsigned long)(off)) & 0xFCUL))
-
-#define MACRISC_CFA1(bus, devfn, off)	\
-	((((unsigned long)(bus)) << 16) \
-	|(((unsigned long)(devfn)) << 8) \
-	|(((unsigned long)(off)) & 0xFCUL) \
-	|1UL)
-
-static void volatile __iomem *
-macrisc_cfg_access(struct pci_controller* hose, u8 bus, u8 dev_fn, u8 offset)
-{
-	unsigned int caddr;
-
-	if (bus == hose->first_busno) {
-		if (dev_fn < (11 << 3))
-			return NULL;
-		caddr = MACRISC_CFA0(dev_fn, offset);
-	} else
-		caddr = MACRISC_CFA1(bus, dev_fn, offset);
-
-	/* Uninorth will return garbage if we don't read back the value ! */
-	do {
-		out_le32(hose->cfg_addr, caddr);
-	} while (in_le32(hose->cfg_addr) != caddr);
-
-	offset &= has_uninorth ? 0x07 : 0x03;
-	return hose->cfg_data + offset;
-}
-
-static int
-macrisc_read_config(struct pci_bus *bus, unsigned int devfn, int offset,
-		    int len, u32 *val)
-{
-	struct pci_controller *hose = bus->sysdata;
-	void volatile __iomem *addr;
-
-	addr = macrisc_cfg_access(hose, bus->number, devfn, offset);
-	if (!addr)
-		return PCIBIOS_DEVICE_NOT_FOUND;
-	/*
-	 * Note: the caller has already checked that offset is
-	 * suitably aligned and that len is 1, 2 or 4.
-	 */
-	switch (len) {
-	case 1:
-		*val = in_8(addr);
-		break;
-	case 2:
-		*val = in_le16(addr);
-		break;
-	default:
-		*val = in_le32(addr);
-		break;
-	}
-	return PCIBIOS_SUCCESSFUL;
-}
-
-static int
-macrisc_write_config(struct pci_bus *bus, unsigned int devfn, int offset,
-		     int len, u32 val)
-{
-	struct pci_controller *hose = bus->sysdata;
-	void volatile __iomem *addr;
-
-	addr = macrisc_cfg_access(hose, bus->number, devfn, offset);
-	if (!addr)
-		return PCIBIOS_DEVICE_NOT_FOUND;
-	/*
-	 * Note: the caller has already checked that offset is
-	 * suitably aligned and that len is 1, 2 or 4.
-	 */
-	switch (len) {
-	case 1:
-		out_8(addr, val);
-		(void) in_8(addr);
-		break;
-	case 2:
-		out_le16(addr, val);
-		(void) in_le16(addr);
-		break;
-	default:
-		out_le32(addr, val);
-		(void) in_le32(addr);
-		break;
-	}
-	return PCIBIOS_SUCCESSFUL;
-}
-
-static struct pci_ops macrisc_pci_ops =
-{
-	macrisc_read_config,
-	macrisc_write_config
-};
-
-/*
- * Verifiy that a specific (bus, dev_fn) exists on chaos
- */
-static int
-chaos_validate_dev(struct pci_bus *bus, int devfn, int offset)
-{
-	struct device_node *np;
-	u32 *vendor, *device;
-
-	np = pci_busdev_to_OF_node(bus, devfn);
-	if (np == NULL)
-		return PCIBIOS_DEVICE_NOT_FOUND;
-
-	vendor = (u32 *)get_property(np, "vendor-id", NULL);
-	device = (u32 *)get_property(np, "device-id", NULL);
-	if (vendor == NULL || device == NULL)
-		return PCIBIOS_DEVICE_NOT_FOUND;
-
-	if ((*vendor == 0x106b) && (*device == 3) && (offset >= 0x10)
-	    && (offset != 0x14) && (offset != 0x18) && (offset <= 0x24))
-		return PCIBIOS_BAD_REGISTER_NUMBER;
-
-	return PCIBIOS_SUCCESSFUL;
-}
-
-static int
-chaos_read_config(struct pci_bus *bus, unsigned int devfn, int offset,
-		  int len, u32 *val)
-{
-	int result = chaos_validate_dev(bus, devfn, offset);
-	if (result == PCIBIOS_BAD_REGISTER_NUMBER)
-		*val = ~0U;
-	if (result != PCIBIOS_SUCCESSFUL)
-		return result;
-	return macrisc_read_config(bus, devfn, offset, len, val);
-}
-
-static int
-chaos_write_config(struct pci_bus *bus, unsigned int devfn, int offset,
-		   int len, u32 val)
-{
-	int result = chaos_validate_dev(bus, devfn, offset);
-	if (result != PCIBIOS_SUCCESSFUL)
-		return result;
-	return macrisc_write_config(bus, devfn, offset, len, val);
-}
-
-static struct pci_ops chaos_pci_ops =
-{
-	chaos_read_config,
-	chaos_write_config
-};
-
-#ifdef CONFIG_POWER4
-
-/*
- * These versions of U3 HyperTransport config space access ops do not
- * implement self-view of the HT host yet
- */
-
-#define U3_HT_CFA0(devfn, off)		\
-		((((unsigned long)devfn) << 8) | offset)
-#define U3_HT_CFA1(bus, devfn, off)	\
-		(U3_HT_CFA0(devfn, off) \
-		+ (((unsigned long)bus) << 16) \
-		+ 0x01000000UL)
-
-static void volatile __iomem *
-u3_ht_cfg_access(struct pci_controller* hose, u8 bus, u8 devfn, u8 offset)
-{
-	if (bus == hose->first_busno) {
-		/* For now, we don't self probe U3 HT bridge */
-		if (PCI_FUNC(devfn) != 0 || PCI_SLOT(devfn) > 7 ||
-		    PCI_SLOT(devfn) < 1)
-			return 0;
-		return hose->cfg_data + U3_HT_CFA0(devfn, offset);
-	} else
-		return hose->cfg_data + U3_HT_CFA1(bus, devfn, offset);
-}
-
-static int
-u3_ht_read_config(struct pci_bus *bus, unsigned int devfn, int offset,
-		    int len, u32 *val)
-{
-	struct pci_controller *hose = bus->sysdata;
-	void volatile __iomem *addr;
-	int i;
-
-	struct device_node *np = pci_busdev_to_OF_node(bus, devfn);
-	if (np == NULL)
-		return PCIBIOS_DEVICE_NOT_FOUND;
-
-	/*
-	 * When a device in K2 is powered down, we die on config
-	 * cycle accesses. Fix that here.
-	 */
-	for (i=0; i<2; i++)
-		if (k2_skiplist[i] == np) {
-			switch (len) {
-			case 1:
-				*val = 0xff; break;
-			case 2:
-				*val = 0xffff; break;
-			default:
-				*val = 0xfffffffful; break;
-			}
-			return PCIBIOS_SUCCESSFUL;
-		}
-	    
-	addr = u3_ht_cfg_access(hose, bus->number, devfn, offset);
-	if (!addr)
-		return PCIBIOS_DEVICE_NOT_FOUND;
-	/*
-	 * Note: the caller has already checked that offset is
-	 * suitably aligned and that len is 1, 2 or 4.
-	 */
-	switch (len) {
-	case 1:
-		*val = in_8(addr);
-		break;
-	case 2:
-		*val = in_le16(addr);
-		break;
-	default:
-		*val = in_le32(addr);
-		break;
-	}
-	return PCIBIOS_SUCCESSFUL;
-}
-
-static int
-u3_ht_write_config(struct pci_bus *bus, unsigned int devfn, int offset,
-		     int len, u32 val)
-{
-	struct pci_controller *hose = bus->sysdata;
-	void volatile __iomem *addr;
-	int i;
-
-	struct device_node *np = pci_busdev_to_OF_node(bus, devfn);
-	if (np == NULL)
-		return PCIBIOS_DEVICE_NOT_FOUND;
-	/*
-	 * When a device in K2 is powered down, we die on config
-	 * cycle accesses. Fix that here.
-	 */
-	for (i=0; i<2; i++)
-		if (k2_skiplist[i] == np)
-			return PCIBIOS_SUCCESSFUL;
-
-	addr = u3_ht_cfg_access(hose, bus->number, devfn, offset);
-	if (!addr)
-		return PCIBIOS_DEVICE_NOT_FOUND;
-	/*
-	 * Note: the caller has already checked that offset is
-	 * suitably aligned and that len is 1, 2 or 4.
-	 */
-	switch (len) {
-	case 1:
-		out_8(addr, val);
-		(void) in_8(addr);
-		break;
-	case 2:
-		out_le16(addr, val);
-		(void) in_le16(addr);
-		break;
-	default:
-		out_le32(addr, val);
-		(void) in_le32(addr);
-		break;
-	}
-	return PCIBIOS_SUCCESSFUL;
-}
-
-static struct pci_ops u3_ht_pci_ops =
-{
-	u3_ht_read_config,
-	u3_ht_write_config
-};
-
-#endif /* CONFIG_POWER4 */
-
-/*
- * For a bandit bridge, turn on cache coherency if necessary.
- * N.B. we could clean this up using the hose ops directly.
- */
-static void __init
-init_bandit(struct pci_controller *bp)
-{
-	unsigned int vendev, magic;
-	int rev;
-
-	/* read the word at offset 0 in config space for device 11 */
-	out_le32(bp->cfg_addr, (1UL << BANDIT_DEVNUM) + PCI_VENDOR_ID);
-	udelay(2);
-	vendev = in_le32(bp->cfg_data);
-	if (vendev == (PCI_DEVICE_ID_APPLE_BANDIT << 16) +
-			PCI_VENDOR_ID_APPLE) {
-		/* read the revision id */
-		out_le32(bp->cfg_addr,
-			 (1UL << BANDIT_DEVNUM) + PCI_REVISION_ID);
-		udelay(2);
-		rev = in_8(bp->cfg_data);
-		if (rev != BANDIT_REVID)
-			printk(KERN_WARNING
-			       "Unknown revision %d for bandit\n", rev);
-	} else if (vendev != (BANDIT_DEVID_2 << 16) + PCI_VENDOR_ID_APPLE) {
-		printk(KERN_WARNING "bandit isn't? (%x)\n", vendev);
-		return;
-	}
-
-	/* read the word at offset 0x50 */
-	out_le32(bp->cfg_addr, (1UL << BANDIT_DEVNUM) + BANDIT_MAGIC);
-	udelay(2);
-	magic = in_le32(bp->cfg_data);
-	if ((magic & BANDIT_COHERENT) != 0)
-		return;
-	magic |= BANDIT_COHERENT;
-	udelay(2);
-	out_le32(bp->cfg_data, magic);
-	printk(KERN_INFO "Cache coherency enabled for bandit/PSX\n");
-}
-
-
-/*
- * Tweak the PCI-PCI bridge chip on the blue & white G3s.
- */
-static void __init
-init_p2pbridge(void)
-{
-	struct device_node *p2pbridge;
-	struct pci_controller* hose;
-	u8 bus, devfn;
-	u16 val;
-
-	/* XXX it would be better here to identify the specific
-	   PCI-PCI bridge chip we have. */
-	if ((p2pbridge = find_devices("pci-bridge")) == 0
-	    || p2pbridge->parent == NULL
-	    || strcmp(p2pbridge->parent->name, "pci") != 0)
-		return;
-	if (pci_device_from_OF_node(p2pbridge, &bus, &devfn) < 0) {
-		DBG("Can't find PCI infos for PCI<->PCI bridge\n");
-		return;
-	}
-	/* Warning: At this point, we have not yet renumbered all busses.
-	 * So we must use OF walking to find out hose
-	 */
-	hose = pci_find_hose_for_OF_device(p2pbridge);
-	if (!hose) {
-		DBG("Can't find hose for PCI<->PCI bridge\n");
-		return;
-	}
-	if (early_read_config_word(hose, bus, devfn,
-				   PCI_BRIDGE_CONTROL, &val) < 0) {
-		printk(KERN_ERR "init_p2pbridge: couldn't read bridge control\n");
-		return;
-	}
-	val &= ~PCI_BRIDGE_CTL_MASTER_ABORT;
-	early_write_config_word(hose, bus, devfn, PCI_BRIDGE_CONTROL, val);
-}
-
-/*
- * Some Apple desktop machines have a NEC PD720100A USB2 controller
- * on the motherboard. Open Firmware, on these, will disable the
- * EHCI part of it so it behaves like a pair of OHCI's. This fixup
- * code re-enables it ;)
- */
-static void __init
-fixup_nec_usb2(void)
-{
-	struct device_node *nec;
-
-	for (nec = NULL; (nec = of_find_node_by_name(nec, "usb")) != NULL;) {
-		struct pci_controller *hose;
-		u32 data, *prop;
-		u8 bus, devfn;
-		
-		prop = (u32 *)get_property(nec, "vendor-id", NULL);
-		if (prop == NULL)
-			continue;
-		if (0x1033 != *prop)
-			continue;
-		prop = (u32 *)get_property(nec, "device-id", NULL);
-		if (prop == NULL)
-			continue;
-		if (0x0035 != *prop)
-			continue;
-		prop = (u32 *)get_property(nec, "reg", NULL);
-		if (prop == NULL)
-			continue;
-		devfn = (prop[0] >> 8) & 0xff;
-		bus = (prop[0] >> 16) & 0xff;
-		if (PCI_FUNC(devfn) != 0)
-			continue;
-		hose = pci_find_hose_for_OF_device(nec);
-		if (!hose)
-			continue;
-		early_read_config_dword(hose, bus, devfn, 0xe4, &data);
-		if (data & 1UL) {
-			printk("Found NEC PD720100A USB2 chip with disabled EHCI, fixing up...\n");
-			data &= ~1UL;
-			early_write_config_dword(hose, bus, devfn, 0xe4, data);
-			early_write_config_byte(hose, bus, devfn | 2, PCI_INTERRUPT_LINE,
-				nec->intrs[0].line);
-		}
-	}
-}
-
-void __init
-pmac_find_bridges(void)
-{
-	struct device_node *np, *root;
-	struct device_node *ht = NULL;
-
-	root = of_find_node_by_path("/");
-	if (root == NULL) {
-		printk(KERN_CRIT "pmac_find_bridges: can't find root of device tree\n");
-		return;
-	}
-	for (np = NULL; (np = of_get_next_child(root, np)) != NULL;) {
-		if (np->name == NULL)
-			continue;
-		if (strcmp(np->name, "bandit") == 0
-		    || strcmp(np->name, "chaos") == 0
-		    || strcmp(np->name, "pci") == 0) {
-			if (add_bridge(np) == 0)
-				of_node_get(np);
-		}
-		if (strcmp(np->name, "ht") == 0) {
-			of_node_get(np);
-			ht = np;
-		}
-	}
-	of_node_put(root);
-
-	/* Probe HT last as it relies on the agp resources to be already
-	 * setup
-	 */
-	if (ht && add_bridge(ht) != 0)
-		of_node_put(ht);
-
-	init_p2pbridge();
-	fixup_nec_usb2();
-	
-	/* We are still having some issues with the Xserve G4, enabling
-	 * some offset between bus number and domains for now when we
-	 * assign all busses should help for now
-	 */
-	if (pci_assign_all_buses)
-		pcibios_assign_bus_offset = 0x10;
-
-#ifdef CONFIG_POWER4 
-	/* There is something wrong with DMA on U3/HT. I haven't figured out
-	 * the details yet, but if I set the cache line size to 128 bytes like
-	 * it should, I'm getting memory corruption caused by devices like
-	 * sungem (even without the MWI bit set, but maybe sungem doesn't
-	 * care). Right now, it appears that setting up a 64 bytes line size
-	 * works properly, 64 bytes beeing the max transfer size of HT, I
-	 * suppose this is related the way HT/PCI are hooked together. I still
-	 * need to dive into more specs though to be really sure of what's
-	 * going on. --BenH.
-	 *
-	 * Ok, apparently, it's just that HT can't do more than 64 bytes
-	 * transactions. MWI seem to be meaningless there as well, it may
-	 * be worth nop'ing out pci_set_mwi too though I haven't done that
-	 * yet.
-	 *
-	 * Note that it's a bit different for whatever is in the AGP slot.
-	 * For now, I don't care, but this can become a real issue, we
-	 * should probably hook pci_set_mwi anyway to make sure it sets
-	 * the real cache line size in there.
-	 */
-	if (machine_is_compatible("MacRISC4"))
-		pci_cache_line_size = 16; /* 64 bytes */
-
-	pmac_check_ht_link();
-#endif /* CONFIG_POWER4 */
-}
-
-#define GRACKLE_CFA(b, d, o)	(0x80 | ((b) << 8) | ((d) << 16) \
-				 | (((o) & ~3) << 24))
-
-#define GRACKLE_PICR1_STG		0x00000040
-#define GRACKLE_PICR1_LOOPSNOOP		0x00000010
-
-/* N.B. this is called before bridges is initialized, so we can't
-   use grackle_pcibios_{read,write}_config_dword. */
-static inline void grackle_set_stg(struct pci_controller* bp, int enable)
-{
-	unsigned int val;
-
-	out_be32(bp->cfg_addr, GRACKLE_CFA(0, 0, 0xa8));
-	val = in_le32(bp->cfg_data);
-	val = enable? (val | GRACKLE_PICR1_STG) :
-		(val & ~GRACKLE_PICR1_STG);
-	out_be32(bp->cfg_addr, GRACKLE_CFA(0, 0, 0xa8));
-	out_le32(bp->cfg_data, val);
-	(void)in_le32(bp->cfg_data);
-}
-
-static inline void grackle_set_loop_snoop(struct pci_controller *bp, int enable)
-{
-	unsigned int val;
-
-	out_be32(bp->cfg_addr, GRACKLE_CFA(0, 0, 0xa8));
-	val = in_le32(bp->cfg_data);
-	val = enable? (val | GRACKLE_PICR1_LOOPSNOOP) :
-		(val & ~GRACKLE_PICR1_LOOPSNOOP);
-	out_be32(bp->cfg_addr, GRACKLE_CFA(0, 0, 0xa8));
-	out_le32(bp->cfg_data, val);
-	(void)in_le32(bp->cfg_data);
-}
-
-static int __init
-setup_uninorth(struct pci_controller* hose, struct reg_property* addr)
-{
-	pci_assign_all_buses = 1;
-	has_uninorth = 1;
-	hose->ops = &macrisc_pci_ops;
-	hose->cfg_addr = ioremap(addr->address + 0x800000, 0x1000);
-	hose->cfg_data = ioremap(addr->address + 0xc00000, 0x1000);
-	/* We "know" that the bridge at f2000000 has the PCI slots. */
-	return addr->address == 0xf2000000;
-}
-
-static void __init
-setup_bandit(struct pci_controller* hose, struct reg_property* addr)
-{
-	hose->ops = &macrisc_pci_ops;
-	hose->cfg_addr = ioremap(addr->address + 0x800000, 0x1000);
-	hose->cfg_data = ioremap(addr->address + 0xc00000, 0x1000);
-	init_bandit(hose);
-}
-
-static void __init
-setup_chaos(struct pci_controller* hose, struct reg_property* addr)
-{
-	/* assume a `chaos' bridge */
-	hose->ops = &chaos_pci_ops;
-	hose->cfg_addr = ioremap(addr->address + 0x800000, 0x1000);
-	hose->cfg_data = ioremap(addr->address + 0xc00000, 0x1000);
-}
-
-#ifdef CONFIG_POWER4
-
-static void __init
-setup_u3_agp(struct pci_controller* hose, struct reg_property* addr)
-{
-	/* On G5, we move AGP up to high bus number so we don't need
-	 * to reassign bus numbers for HT. If we ever have P2P bridges
-	 * on AGP, we'll have to move pci_assign_all_buses to the
-	 * pci_controller structure so we enable it for AGP and not for
-	 * HT childs.
-	 * We hard code the address because of the different size of
-	 * the reg address cell, we shall fix that by killing struct
-	 * reg_property and using some accessor functions instead
-	 */
-       	hose->first_busno = 0xf0;
-	hose->last_busno = 0xff;
-	has_uninorth = 1;
-	hose->ops = &macrisc_pci_ops;
-	hose->cfg_addr = ioremap(0xf0000000 + 0x800000, 0x1000);
-	hose->cfg_data = ioremap(0xf0000000 + 0xc00000, 0x1000);
-
-	u3_agp = hose;
-}
-
-static void __init
-setup_u3_ht(struct pci_controller* hose, struct reg_property *addr)
-{
-	struct device_node *np = (struct device_node *)hose->arch_data;
-	int i, cur;
-
-	hose->ops = &u3_ht_pci_ops;
-
-	/* We hard code the address because of the different size of
-	 * the reg address cell, we shall fix that by killing struct
-	 * reg_property and using some accessor functions instead
-	 */
-	hose->cfg_data = ioremap(0xf2000000, 0x02000000);
-
-	/*
-	 * /ht node doesn't expose a "ranges" property, so we "remove" regions that
-	 * have been allocated to AGP. So far, this version of the code doesn't assign
-	 * any of the 0xfxxxxxxx "fine" memory regions to /ht.
-	 * We need to fix that sooner or later by either parsing all child "ranges"
-	 * properties or figuring out the U3 address space decoding logic and
-	 * then read its configuration register (if any).
-	 */
-	hose->io_base_phys = 0xf4000000;
-	hose->io_base_virt = ioremap(hose->io_base_phys, 0x00400000);
-	isa_io_base = (unsigned long) hose->io_base_virt;
-	hose->io_resource.name = np->full_name;
-	hose->io_resource.start = 0;
-	hose->io_resource.end = 0x003fffff;
-	hose->io_resource.flags = IORESOURCE_IO;
-	hose->pci_mem_offset = 0;
-	hose->first_busno = 0;
-	hose->last_busno = 0xef;
-	hose->mem_resources[0].name = np->full_name;
-	hose->mem_resources[0].start = 0x80000000;
-	hose->mem_resources[0].end = 0xefffffff;
-	hose->mem_resources[0].flags = IORESOURCE_MEM;
-
-	if (u3_agp == NULL) {
-		DBG("U3 has no AGP, using full resource range\n");
-		return;
-	}
-
-	/* We "remove" the AGP resources from the resources allocated to HT, that
-	 * is we create "holes". However, that code does assumptions that so far
-	 * happen to be true (cross fingers...), typically that resources in the
-	 * AGP node are properly ordered
-	 */
-	cur = 0;
-	for (i=0; i<3; i++) {
-		struct resource *res = &u3_agp->mem_resources[i];
-		if (res->flags != IORESOURCE_MEM)
-			continue;
-		/* We don't care about "fine" resources */
-		if (res->start >= 0xf0000000)
-			continue;
-		/* Check if it's just a matter of "shrinking" us in one direction */
-		if (hose->mem_resources[cur].start == res->start) {
-			DBG("U3/HT: shrink start of %d, %08lx -> %08lx\n",
-			    cur, hose->mem_resources[cur].start, res->end + 1);
-			hose->mem_resources[cur].start = res->end + 1;
-			continue;
-		}
-		if (hose->mem_resources[cur].end == res->end) {
-			DBG("U3/HT: shrink end of %d, %08lx -> %08lx\n",
-			    cur, hose->mem_resources[cur].end, res->start - 1);
-			hose->mem_resources[cur].end = res->start - 1;
-			continue;
-		}
-		/* No, it's not the case, we need a hole */
-		if (cur == 2) {
-			/* not enough resources to make a hole, we drop part of the range */
-			printk(KERN_WARNING "Running out of resources for /ht host !\n");
-			hose->mem_resources[cur].end = res->start - 1;
-			continue;
-		}		
-		cur++;
-       		DBG("U3/HT: hole, %d end at %08lx, %d start at %08lx\n",
-		    cur-1, res->start - 1, cur, res->end + 1);
-		hose->mem_resources[cur].name = np->full_name;
-		hose->mem_resources[cur].flags = IORESOURCE_MEM;
-		hose->mem_resources[cur].start = res->end + 1;
-		hose->mem_resources[cur].end = hose->mem_resources[cur-1].end;
-		hose->mem_resources[cur-1].end = res->start - 1;
-	}
-}
-
-#endif /* CONFIG_POWER4 */
-
-void __init
-setup_grackle(struct pci_controller *hose)
-{
-	setup_indirect_pci(hose, 0xfec00000, 0xfee00000);
-	if (machine_is_compatible("AAPL,PowerBook1998"))
-		grackle_set_loop_snoop(hose, 1);
-#if 0	/* Disabled for now, HW problems ??? */
-	grackle_set_stg(hose, 1);
-#endif
-}
-
-/*
- * We assume that if we have a G3 powermac, we have one bridge called
- * "pci" (a MPC106) and no bandit or chaos bridges, and contrariwise,
- * if we have one or more bandit or chaos bridges, we don't have a MPC106.
- */
-static int __init
-add_bridge(struct device_node *dev)
-{
-	int len;
-	struct pci_controller *hose;
-	struct reg_property *addr;
-	char* disp_name;
-	int *bus_range;
-	int primary = 1;
-
-	DBG("Adding PCI host bridge %s\n", dev->full_name);
-
-       	addr = (struct reg_property *) get_property(dev, "reg", &len);
-       	if (addr == NULL || len < sizeof(*addr)) {
-       		printk(KERN_WARNING "Can't use %s: no address\n",
-       		       dev->full_name);
-       		return -ENODEV;
-       	}
-       	bus_range = (int *) get_property(dev, "bus-range", &len);
-       	if (bus_range == NULL || len < 2 * sizeof(int)) {
-       		printk(KERN_WARNING "Can't get bus-range for %s, assume bus 0\n",
-       			       dev->full_name);
-       	}
-
-       	hose = pcibios_alloc_controller();
-       	if (!hose)
-       		return -ENOMEM;
-       	hose->arch_data = dev;
-       	hose->first_busno = bus_range ? bus_range[0] : 0;
-       	hose->last_busno = bus_range ? bus_range[1] : 0xff;
-
-	disp_name = NULL;
-#ifdef CONFIG_POWER4
-       	if (device_is_compatible(dev, "u3-agp")) {
-       		setup_u3_agp(hose, addr);
-       		disp_name = "U3-AGP";
-       		primary = 0;
-       	} else if (device_is_compatible(dev, "u3-ht")) {
-       		setup_u3_ht(hose, addr);
-       		disp_name = "U3-HT";
-       		primary = 1;
-       	} else
-#endif /* CONFIG_POWER4 */
-	if (device_is_compatible(dev, "uni-north")) {
-       		primary = setup_uninorth(hose, addr);
-       		disp_name = "UniNorth";
-       	} else if (strcmp(dev->name, "pci") == 0) {
-       		/* XXX assume this is a mpc106 (grackle) */
-       		setup_grackle(hose);
-       		disp_name = "Grackle (MPC106)";
-       	} else if (strcmp(dev->name, "bandit") == 0) {
-       		setup_bandit(hose, addr);
-       		disp_name = "Bandit";
-       	} else if (strcmp(dev->name, "chaos") == 0) {
-       		setup_chaos(hose, addr);
-       		disp_name = "Chaos";
-       		primary = 0;
-       	}
-       	printk(KERN_INFO "Found %s PCI host bridge at 0x%08x. Firmware bus number: %d->%d\n",
-       		disp_name, addr->address, hose->first_busno, hose->last_busno);
-       	DBG(" ->Hose at 0x%p, cfg_addr=0x%p,cfg_data=0x%p\n",
-       		hose, hose->cfg_addr, hose->cfg_data);
-
-       	/* Interpret the "ranges" property */
-       	/* This also maps the I/O region and sets isa_io/mem_base */
-       	pci_process_bridge_OF_ranges(hose, dev, primary);
-
-       	/* Fixup "bus-range" OF property */
-       	fixup_bus_range(dev);
-
-	return 0;
-}
-
-static void __init
-pcibios_fixup_OF_interrupts(void)
-{
-	struct pci_dev* dev = NULL;
-
-	/*
-	 * Open Firmware often doesn't initialize the
-	 * PCI_INTERRUPT_LINE config register properly, so we
-	 * should find the device node and apply the interrupt
-	 * obtained from the OF device-tree
-	 */
-	for_each_pci_dev(dev) {
-		struct device_node *node;
-		node = pci_device_to_OF_node(dev);
-		/* this is the node, see if it has interrupts */
-		if (node && node->n_intrs > 0)
-			dev->irq = node->intrs[0].line;
-		pci_write_config_byte(dev, PCI_INTERRUPT_LINE, dev->irq);
-	}
-}
-
-void __init
-pmac_pcibios_fixup(void)
-{
-	/* Fixup interrupts according to OF tree */
-	pcibios_fixup_OF_interrupts();
-}
-
-int
-pmac_pci_enable_device_hook(struct pci_dev *dev, int initial)
-{
-	struct device_node* node;
-	int updatecfg = 0;
-	int uninorth_child;
-
-	node = pci_device_to_OF_node(dev);
-
-	/* We don't want to enable USB controllers absent from the OF tree
-	 * (iBook second controller)
-	 */
-	if (dev->vendor == PCI_VENDOR_ID_APPLE
-	    && (dev->class == ((PCI_CLASS_SERIAL_USB << 8) | 0x10))
-	    && !node) {
-		printk(KERN_INFO "Apple USB OHCI %s disabled by firmware\n",
-		       pci_name(dev));
-		return -EINVAL;
-	}
-
-	if (!node)
-		return 0;
-
-	uninorth_child = node->parent &&
-		device_is_compatible(node->parent, "uni-north");
-	
-	/* Firewire & GMAC were disabled after PCI probe, the driver is
-	 * claiming them, we must re-enable them now.
-	 */
-	if (uninorth_child && !strcmp(node->name, "firewire") &&
-	    (device_is_compatible(node, "pci106b,18") ||
-	     device_is_compatible(node, "pci106b,30") ||
-	     device_is_compatible(node, "pci11c1,5811"))) {
-		pmac_call_feature(PMAC_FTR_1394_CABLE_POWER, node, 0, 1);
-		pmac_call_feature(PMAC_FTR_1394_ENABLE, node, 0, 1);
-		updatecfg = 1;
-	}
-	if (uninorth_child && !strcmp(node->name, "ethernet") &&
-	    device_is_compatible(node, "gmac")) {
-		pmac_call_feature(PMAC_FTR_GMAC_ENABLE, node, 0, 1);
-		updatecfg = 1;
-	}
-
-	if (updatecfg) {
-		u16 cmd;
-	
-		/*
-		 * Make sure PCI is correctly configured
-		 *
-		 * We use old pci_bios versions of the function since, by
-		 * default, gmac is not powered up, and so will be absent
-		 * from the kernel initial PCI lookup.
-		 *
-		 * Should be replaced by 2.4 new PCI mechanisms and really
-		 * register the device.
-		 */
-		pci_read_config_word(dev, PCI_COMMAND, &cmd);
-		cmd |= PCI_COMMAND_MEMORY | PCI_COMMAND_MASTER | PCI_COMMAND_INVALIDATE;
-    		pci_write_config_word(dev, PCI_COMMAND, cmd);
-    		pci_write_config_byte(dev, PCI_LATENCY_TIMER, 16);
-    		pci_write_config_byte(dev, PCI_CACHE_LINE_SIZE, pci_cache_line_size);
-	}
-
-	return 0;
-}
-
-/* We power down some devices after they have been probed. They'll
- * be powered back on later on
- */
-void __init
-pmac_pcibios_after_init(void)
-{
-	struct device_node* nd;
-
-#ifdef CONFIG_BLK_DEV_IDE
-	struct pci_dev *dev = NULL;
-
-	/* OF fails to initialize IDE controllers on macs
-	 * (and maybe other machines)
-	 *
-	 * Ideally, this should be moved to the IDE layer, but we need
-	 * to check specifically with Andre Hedrick how to do it cleanly
-	 * since the common IDE code seem to care about the fact that the
-	 * BIOS may have disabled a controller.
-	 *
-	 * -- BenH
-	 */
-	for_each_pci_dev(dev) {
-		if ((dev->class >> 16) == PCI_BASE_CLASS_STORAGE)
-			pci_enable_device(dev);
-	}
-#endif /* CONFIG_BLK_DEV_IDE */
-
-	nd = find_devices("firewire");
-	while (nd) {
-		if (nd->parent && (device_is_compatible(nd, "pci106b,18") ||
-				   device_is_compatible(nd, "pci106b,30") ||
-				   device_is_compatible(nd, "pci11c1,5811"))
-		    && device_is_compatible(nd->parent, "uni-north")) {
-			pmac_call_feature(PMAC_FTR_1394_ENABLE, nd, 0, 0);
-			pmac_call_feature(PMAC_FTR_1394_CABLE_POWER, nd, 0, 0);
-		}
-		nd = nd->next;
-	}
-	nd = find_devices("ethernet");
-	while (nd) {
-		if (nd->parent && device_is_compatible(nd, "gmac")
-		    && device_is_compatible(nd->parent, "uni-north"))
-			pmac_call_feature(PMAC_FTR_GMAC_ENABLE, nd, 0, 0);
-		nd = nd->next;
-	}
-}
-
-void pmac_pci_fixup_cardbus(struct pci_dev* dev)
-{
-	if (_machine != _MACH_Pmac)
-		return;
-	/*
-	 * Fix the interrupt routing on the various cardbus bridges
-	 * used on powerbooks
-	 */
-	if (dev->vendor != PCI_VENDOR_ID_TI)
-		return;
-	if (dev->device == PCI_DEVICE_ID_TI_1130 ||
-	    dev->device == PCI_DEVICE_ID_TI_1131) {
-		u8 val;
-	    	/* Enable PCI interrupt */
-		if (pci_read_config_byte(dev, 0x91, &val) == 0)
-			pci_write_config_byte(dev, 0x91, val | 0x30);
-		/* Disable ISA interrupt mode */
-		if (pci_read_config_byte(dev, 0x92, &val) == 0)
-			pci_write_config_byte(dev, 0x92, val & ~0x06);
-	}
-	if (dev->device == PCI_DEVICE_ID_TI_1210 ||
-	    dev->device == PCI_DEVICE_ID_TI_1211 ||
-	    dev->device == PCI_DEVICE_ID_TI_1410 ||
-	    dev->device == PCI_DEVICE_ID_TI_1510) {
-		u8 val;
-		/* 0x8c == TI122X_IRQMUX, 2 says to route the INTA
-		   signal out the MFUNC0 pin */
-		if (pci_read_config_byte(dev, 0x8c, &val) == 0)
-			pci_write_config_byte(dev, 0x8c, (val & ~0x0f) | 2);
-		/* Disable ISA interrupt mode */
-		if (pci_read_config_byte(dev, 0x92, &val) == 0)
-			pci_write_config_byte(dev, 0x92, val & ~0x06);
-	}
-}
-
-DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_TI, PCI_ANY_ID, pmac_pci_fixup_cardbus);
-
-void pmac_pci_fixup_pciata(struct pci_dev* dev)
-{
-       u8 progif = 0;
-
-       /*
-        * On PowerMacs, we try to switch any PCI ATA controller to
-	* fully native mode
-        */
-	if (_machine != _MACH_Pmac)
-		return;
-	/* Some controllers don't have the class IDE */
-	if (dev->vendor == PCI_VENDOR_ID_PROMISE)
-		switch(dev->device) {
-		case PCI_DEVICE_ID_PROMISE_20246:
-		case PCI_DEVICE_ID_PROMISE_20262:
-		case PCI_DEVICE_ID_PROMISE_20263:
-		case PCI_DEVICE_ID_PROMISE_20265:
-		case PCI_DEVICE_ID_PROMISE_20267:
-		case PCI_DEVICE_ID_PROMISE_20268:
-		case PCI_DEVICE_ID_PROMISE_20269:
-		case PCI_DEVICE_ID_PROMISE_20270:
-		case PCI_DEVICE_ID_PROMISE_20271:
-		case PCI_DEVICE_ID_PROMISE_20275:
-		case PCI_DEVICE_ID_PROMISE_20276:
-		case PCI_DEVICE_ID_PROMISE_20277:
-			goto good;
-		}
-	/* Others, check PCI class */
-	if ((dev->class >> 8) != PCI_CLASS_STORAGE_IDE)
-		return;
- good:
-	pci_read_config_byte(dev, PCI_CLASS_PROG, &progif);
-	if ((progif & 5) != 5) {
-		printk(KERN_INFO "Forcing PCI IDE into native mode: %s\n", pci_name(dev));
-		(void) pci_write_config_byte(dev, PCI_CLASS_PROG, progif|5);
-		if (pci_read_config_byte(dev, PCI_CLASS_PROG, &progif) ||
-		    (progif & 5) != 5)
-			printk(KERN_ERR "Rewrite of PROGIF failed !\n");
-	}
-}
-DECLARE_PCI_FIXUP_FINAL(PCI_ANY_ID, PCI_ANY_ID, pmac_pci_fixup_pciata);
-
-
-/*
- * Disable second function on K2-SATA, it's broken
- * and disable IO BARs on first one
- */
-void pmac_pci_fixup_k2_sata(struct pci_dev* dev)
-{
-	int i;
-	u16 cmd;
-
-	if (PCI_FUNC(dev->devfn) > 0) {
-		pci_read_config_word(dev, PCI_COMMAND, &cmd);
-		cmd &= ~(PCI_COMMAND_IO | PCI_COMMAND_MEMORY);
-		pci_write_config_word(dev, PCI_COMMAND, cmd);
-		for (i = 0; i < 6; i++) {
-			dev->resource[i].start = dev->resource[i].end = 0;
-			dev->resource[i].flags = 0;
-			pci_write_config_dword(dev, PCI_BASE_ADDRESS_0 + 4 * i, 0);
-		}
-	} else {
-		pci_read_config_word(dev, PCI_COMMAND, &cmd);
-		cmd &= ~PCI_COMMAND_IO;
-		pci_write_config_word(dev, PCI_COMMAND, cmd);
-		for (i = 0; i < 5; i++) {
-			dev->resource[i].start = dev->resource[i].end = 0;
-			dev->resource[i].flags = 0;
-			pci_write_config_dword(dev, PCI_BASE_ADDRESS_0 + 4 * i, 0);
-		}
-	}
-}
-DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_SERVERWORKS, 0x0240, pmac_pci_fixup_k2_sata);
diff --git a/arch/ppc/platforms/pmac_pic.c b/arch/ppc/platforms/pmac_pic.c
deleted file mode 100644
index 4742bf60935..00000000000
--- a/arch/ppc/platforms/pmac_pic.c
+++ /dev/null
@@ -1,693 +0,0 @@
-/*
- *  Support for the interrupt controllers found on Power Macintosh,
- *  currently Apple's "Grand Central" interrupt controller in all
- *  it's incarnations. OpenPIC support used on newer machines is
- *  in a separate file
- *
- *  Copyright (C) 1997 Paul Mackerras (paulus@cs.anu.edu.au)
- *
- *  Maintained by Benjamin Herrenschmidt (benh@kernel.crashing.org)
- *
- *  This program is free software; you can redistribute it and/or
- *  modify it under the terms of the GNU General Public License
- *  as published by the Free Software Foundation; either version
- *  2 of the License, or (at your option) any later version.
- *
- */
-
-#include <linux/config.h>
-#include <linux/stddef.h>
-#include <linux/init.h>
-#include <linux/sched.h>
-#include <linux/signal.h>
-#include <linux/pci.h>
-#include <linux/interrupt.h>
-#include <linux/sysdev.h>
-#include <linux/adb.h>
-#include <linux/pmu.h>
-
-#include <asm/sections.h>
-#include <asm/io.h>
-#include <asm/smp.h>
-#include <asm/prom.h>
-#include <asm/pci-bridge.h>
-#include <asm/time.h>
-#include <asm/open_pic.h>
-#include <asm/xmon.h>
-#include <asm/pmac_feature.h>
-#include <asm/machdep.h>
-
-#include "pmac_pic.h"
-
-/*
- * XXX this should be in xmon.h, but putting it there means xmon.h
- * has to include <linux/interrupt.h> (to get irqreturn_t), which
- * causes all sorts of problems.  -- paulus
- */
-extern irqreturn_t xmon_irq(int, void *, struct pt_regs *);
-
-struct pmac_irq_hw {
-        unsigned int    event;
-        unsigned int    enable;
-        unsigned int    ack;
-        unsigned int    level;
-};
-
-/* Default addresses */
-static volatile struct pmac_irq_hw *pmac_irq_hw[4] = {
-        (struct pmac_irq_hw *) 0xf3000020,
-        (struct pmac_irq_hw *) 0xf3000010,
-        (struct pmac_irq_hw *) 0xf4000020,
-        (struct pmac_irq_hw *) 0xf4000010,
-};
-
-#define GC_LEVEL_MASK		0x3ff00000
-#define OHARE_LEVEL_MASK	0x1ff00000
-#define HEATHROW_LEVEL_MASK	0x1ff00000
-
-static int max_irqs;
-static int max_real_irqs;
-static u32 level_mask[4];
-
-static DEFINE_SPINLOCK(pmac_pic_lock);
-
-
-#define GATWICK_IRQ_POOL_SIZE        10
-static struct interrupt_info gatwick_int_pool[GATWICK_IRQ_POOL_SIZE];
-
-#define NR_MASK_WORDS	((NR_IRQS + 31) / 32)
-static unsigned long ppc_lost_interrupts[NR_MASK_WORDS];
-
-/*
- * Mark an irq as "lost".  This is only used on the pmac
- * since it can lose interrupts (see pmac_set_irq_mask).
- * -- Cort
- */
-void
-__set_lost(unsigned long irq_nr, int nokick)
-{
-	if (!test_and_set_bit(irq_nr, ppc_lost_interrupts)) {
-		atomic_inc(&ppc_n_lost_interrupts);
-		if (!nokick)
-			set_dec(1);
-	}
-}
-
-static void
-pmac_mask_and_ack_irq(unsigned int irq_nr)
-{
-        unsigned long bit = 1UL << (irq_nr & 0x1f);
-        int i = irq_nr >> 5;
-        unsigned long flags;
-
-        if ((unsigned)irq_nr >= max_irqs)
-                return;
-
-        clear_bit(irq_nr, ppc_cached_irq_mask);
-        if (test_and_clear_bit(irq_nr, ppc_lost_interrupts))
-                atomic_dec(&ppc_n_lost_interrupts);
-	spin_lock_irqsave(&pmac_pic_lock, flags);
-        out_le32(&pmac_irq_hw[i]->enable, ppc_cached_irq_mask[i]);
-        out_le32(&pmac_irq_hw[i]->ack, bit);
-        do {
-                /* make sure ack gets to controller before we enable
-                   interrupts */
-                mb();
-        } while((in_le32(&pmac_irq_hw[i]->enable) & bit)
-                != (ppc_cached_irq_mask[i] & bit));
-	spin_unlock_irqrestore(&pmac_pic_lock, flags);
-}
-
-static void pmac_set_irq_mask(unsigned int irq_nr, int nokicklost)
-{
-        unsigned long bit = 1UL << (irq_nr & 0x1f);
-        int i = irq_nr >> 5;
-        unsigned long flags;
-
-        if ((unsigned)irq_nr >= max_irqs)
-                return;
-
-	spin_lock_irqsave(&pmac_pic_lock, flags);
-        /* enable unmasked interrupts */
-        out_le32(&pmac_irq_hw[i]->enable, ppc_cached_irq_mask[i]);
-
-        do {
-                /* make sure mask gets to controller before we
-                   return to user */
-                mb();
-        } while((in_le32(&pmac_irq_hw[i]->enable) & bit)
-                != (ppc_cached_irq_mask[i] & bit));
-
-        /*
-         * Unfortunately, setting the bit in the enable register
-         * when the device interrupt is already on *doesn't* set
-         * the bit in the flag register or request another interrupt.
-         */
-        if (bit & ppc_cached_irq_mask[i] & in_le32(&pmac_irq_hw[i]->level))
-		__set_lost((ulong)irq_nr, nokicklost);
-	spin_unlock_irqrestore(&pmac_pic_lock, flags);
-}
-
-/* When an irq gets requested for the first client, if it's an
- * edge interrupt, we clear any previous one on the controller
- */
-static unsigned int pmac_startup_irq(unsigned int irq_nr)
-{
-        unsigned long bit = 1UL << (irq_nr & 0x1f);
-        int i = irq_nr >> 5;
-
-	if ((irq_desc[irq_nr].status & IRQ_LEVEL) == 0)
-		out_le32(&pmac_irq_hw[i]->ack, bit);
-        set_bit(irq_nr, ppc_cached_irq_mask);
-        pmac_set_irq_mask(irq_nr, 0);
-
-	return 0;
-}
-
-static void pmac_mask_irq(unsigned int irq_nr)
-{
-        clear_bit(irq_nr, ppc_cached_irq_mask);
-        pmac_set_irq_mask(irq_nr, 0);
-        mb();
-}
-
-static void pmac_unmask_irq(unsigned int irq_nr)
-{
-        set_bit(irq_nr, ppc_cached_irq_mask);
-        pmac_set_irq_mask(irq_nr, 0);
-}
-
-static void pmac_end_irq(unsigned int irq_nr)
-{
-	if (!(irq_desc[irq_nr].status & (IRQ_DISABLED|IRQ_INPROGRESS))
-	    && irq_desc[irq_nr].action) {
-        	set_bit(irq_nr, ppc_cached_irq_mask);
-	        pmac_set_irq_mask(irq_nr, 1);
-	}
-}
-
-
-struct hw_interrupt_type pmac_pic = {
-	.typename	= " PMAC-PIC ",
-	.startup	= pmac_startup_irq,
-	.enable		= pmac_unmask_irq,
-	.disable	= pmac_mask_irq,
-	.ack		= pmac_mask_and_ack_irq,
-	.end		= pmac_end_irq,
-};
-
-struct hw_interrupt_type gatwick_pic = {
-	.typename	= " GATWICK  ",
-	.startup	= pmac_startup_irq,
-	.enable		= pmac_unmask_irq,
-	.disable	= pmac_mask_irq,
-	.ack		= pmac_mask_and_ack_irq,
-	.end		= pmac_end_irq,
-};
-
-static irqreturn_t gatwick_action(int cpl, void *dev_id, struct pt_regs *regs)
-{
-	int irq, bits;
-
-	for (irq = max_irqs; (irq -= 32) >= max_real_irqs; ) {
-		int i = irq >> 5;
-		bits = in_le32(&pmac_irq_hw[i]->event) | ppc_lost_interrupts[i];
-		/* We must read level interrupts from the level register */
-		bits |= (in_le32(&pmac_irq_hw[i]->level) & level_mask[i]);
-		bits &= ppc_cached_irq_mask[i];
-		if (bits == 0)
-			continue;
-		irq += __ilog2(bits);
-		__do_IRQ(irq, regs);
-		return IRQ_HANDLED;
-	}
-	printk("gatwick irq not from gatwick pic\n");
-	return IRQ_NONE;
-}
-
-int
-pmac_get_irq(struct pt_regs *regs)
-{
-	int irq;
-	unsigned long bits = 0;
-
-#ifdef CONFIG_SMP
-	void psurge_smp_message_recv(struct pt_regs *);
-
-       	/* IPI's are a hack on the powersurge -- Cort */
-       	if ( smp_processor_id() != 0 ) {
-		psurge_smp_message_recv(regs);
-		return -2;	/* ignore, already handled */
-        }
-#endif /* CONFIG_SMP */
-	for (irq = max_real_irqs; (irq -= 32) >= 0; ) {
-		int i = irq >> 5;
-		bits = in_le32(&pmac_irq_hw[i]->event) | ppc_lost_interrupts[i];
-		/* We must read level interrupts from the level register */
-		bits |= (in_le32(&pmac_irq_hw[i]->level) & level_mask[i]);
-		bits &= ppc_cached_irq_mask[i];
-		if (bits == 0)
-			continue;
-		irq += __ilog2(bits);
-		break;
-	}
-
-	return irq;
-}
-
-/* This routine will fix some missing interrupt values in the device tree
- * on the gatwick mac-io controller used by some PowerBooks
- */
-static void __init
-pmac_fix_gatwick_interrupts(struct device_node *gw, int irq_base)
-{
-	struct device_node *node;
-	int count;
-
-	memset(gatwick_int_pool, 0, sizeof(gatwick_int_pool));
-	node = gw->child;
-	count = 0;
-	while(node)
-	{
-		/* Fix SCC */
-		if (strcasecmp(node->name, "escc") == 0)
-			if (node->child) {
-				if (node->child->n_intrs < 3) {
-					node->child->intrs = &gatwick_int_pool[count];
-					count += 3;
-				}
-				node->child->n_intrs = 3;
-				node->child->intrs[0].line = 15+irq_base;
-				node->child->intrs[1].line =  4+irq_base;
-				node->child->intrs[2].line =  5+irq_base;
-				printk(KERN_INFO "irq: fixed SCC on second controller (%d,%d,%d)\n",
-					node->child->intrs[0].line,
-					node->child->intrs[1].line,
-					node->child->intrs[2].line);
-			}
-		/* Fix media-bay & left SWIM */
-		if (strcasecmp(node->name, "media-bay") == 0) {
-			struct device_node* ya_node;
-
-			if (node->n_intrs == 0)
-				node->intrs = &gatwick_int_pool[count++];
-			node->n_intrs = 1;
-			node->intrs[0].line = 29+irq_base;
-			printk(KERN_INFO "irq: fixed media-bay on second controller (%d)\n",
-					node->intrs[0].line);
-
-			ya_node = node->child;
-			while(ya_node)
-			{
-				if (strcasecmp(ya_node->name, "floppy") == 0) {
-					if (ya_node->n_intrs < 2) {
-						ya_node->intrs = &gatwick_int_pool[count];
-						count += 2;
-					}
-					ya_node->n_intrs = 2;
-					ya_node->intrs[0].line = 19+irq_base;
-					ya_node->intrs[1].line =  1+irq_base;
-					printk(KERN_INFO "irq: fixed floppy on second controller (%d,%d)\n",
-						ya_node->intrs[0].line, ya_node->intrs[1].line);
-				}
-				if (strcasecmp(ya_node->name, "ata4") == 0) {
-					if (ya_node->n_intrs < 2) {
-						ya_node->intrs = &gatwick_int_pool[count];
-						count += 2;
-					}
-					ya_node->n_intrs = 2;
-					ya_node->intrs[0].line = 14+irq_base;
-					ya_node->intrs[1].line =  3+irq_base;
-					printk(KERN_INFO "irq: fixed ide on second controller (%d,%d)\n",
-						ya_node->intrs[0].line, ya_node->intrs[1].line);
-				}
-				ya_node = ya_node->sibling;
-			}
-		}
-		node = node->sibling;
-	}
-	if (count > 10) {
-		printk("WARNING !! Gatwick interrupt pool overflow\n");
-		printk("  GATWICK_IRQ_POOL_SIZE = %d\n", GATWICK_IRQ_POOL_SIZE);
-		printk("              requested = %d\n", count);
-	}
-}
-
-/*
- * The PowerBook 3400/2400/3500 can have a combo ethernet/modem
- * card which includes an ohare chip that acts as a second interrupt
- * controller.  If we find this second ohare, set it up and fix the
- * interrupt value in the device tree for the ethernet chip.
- */
-static int __init enable_second_ohare(void)
-{
-	unsigned char bus, devfn;
-	unsigned short cmd;
-        unsigned long addr;
-	struct device_node *irqctrler = find_devices("pci106b,7");
-	struct device_node *ether;
-
-	if (irqctrler == NULL || irqctrler->n_addrs <= 0)
-		return -1;
-	addr = (unsigned long) ioremap(irqctrler->addrs[0].address, 0x40);
-	pmac_irq_hw[1] = (volatile struct pmac_irq_hw *)(addr + 0x20);
-	max_irqs = 64;
-	if (pci_device_from_OF_node(irqctrler, &bus, &devfn) == 0) {
-		struct pci_controller* hose = pci_find_hose_for_OF_device(irqctrler);
-		if (!hose)
-		    printk(KERN_ERR "Can't find PCI hose for OHare2 !\n");
-		else {
-		    early_read_config_word(hose, bus, devfn, PCI_COMMAND, &cmd);
-		    cmd |= PCI_COMMAND_MEMORY | PCI_COMMAND_MASTER;
-	  	    cmd &= ~PCI_COMMAND_IO;
-		    early_write_config_word(hose, bus, devfn, PCI_COMMAND, cmd);
-		}
-	}
-
-	/* Fix interrupt for the modem/ethernet combo controller. The number
-	   in the device tree (27) is bogus (correct for the ethernet-only
-	   board but not the combo ethernet/modem board).
-	   The real interrupt is 28 on the second controller -> 28+32 = 60.
-	*/
-	ether = find_devices("pci1011,14");
-	if (ether && ether->n_intrs > 0) {
-		ether->intrs[0].line = 60;
-		printk(KERN_INFO "irq: Fixed ethernet IRQ to %d\n",
-		       ether->intrs[0].line);
-	}
-
-	/* Return the interrupt number of the cascade */
-	return irqctrler->intrs[0].line;
-}
-
-#ifdef CONFIG_POWER4
-static irqreturn_t k2u3_action(int cpl, void *dev_id, struct pt_regs *regs)
-{
-	int irq;
-
-	irq = openpic2_get_irq(regs);
-	if (irq != -1)
-		__do_IRQ(irq, regs);
-	return IRQ_HANDLED;
-}
-
-static struct irqaction k2u3_cascade_action = {
-	.handler	= k2u3_action,
-	.flags		= 0,
-	.mask		= CPU_MASK_NONE,
-	.name		= "U3->K2 Cascade",
-};
-#endif /* CONFIG_POWER4 */
-
-#ifdef CONFIG_XMON
-static struct irqaction xmon_action = {
-	.handler	= xmon_irq,
-	.flags		= 0,
-	.mask		= CPU_MASK_NONE,
-	.name		= "NMI - XMON"
-};
-#endif
-
-static struct irqaction gatwick_cascade_action = {
-	.handler	= gatwick_action,
-	.flags		= SA_INTERRUPT,
-	.mask		= CPU_MASK_NONE,
-	.name		= "cascade",
-};
-
-void __init pmac_pic_init(void)
-{
-        int i;
-        struct device_node *irqctrler  = NULL;
-        struct device_node *irqctrler2 = NULL;
-	struct device_node *np;
-        unsigned long addr;
-	int irq_cascade = -1;
-
-	/* We first try to detect Apple's new Core99 chipset, since mac-io
-	 * is quite different on those machines and contains an IBM MPIC2.
-	 */
-	np = find_type_devices("open-pic");
-	while(np) {
-		if (np->parent && !strcmp(np->parent->name, "u3"))
-			irqctrler2 = np;
-		else
-			irqctrler = np;
-		np = np->next;
-	}
-	if (irqctrler != NULL)
-	{
-		if (irqctrler->n_addrs > 0)
-		{
-			unsigned char senses[128];
-
-			printk(KERN_INFO "PowerMac using OpenPIC irq controller at 0x%08x\n",
-			       irqctrler->addrs[0].address);
-
-			prom_get_irq_senses(senses, 0, 128);
-			OpenPIC_InitSenses = senses;
-			OpenPIC_NumInitSenses = 128;
-			ppc_md.get_irq = openpic_get_irq;
-			pmac_call_feature(PMAC_FTR_ENABLE_MPIC, irqctrler, 0, 0);
-			OpenPIC_Addr = ioremap(irqctrler->addrs[0].address,
-					       irqctrler->addrs[0].size);
-			openpic_init(0);
-
-#ifdef CONFIG_POWER4
-			if (irqctrler2 != NULL && irqctrler2->n_intrs > 0 &&
-			    irqctrler2->n_addrs > 0) {
-				printk(KERN_INFO "Slave OpenPIC at 0x%08x hooked on IRQ %d\n",
-				       irqctrler2->addrs[0].address,
-				       irqctrler2->intrs[0].line);
-				pmac_call_feature(PMAC_FTR_ENABLE_MPIC, irqctrler2, 0, 0);
-				OpenPIC2_Addr = ioremap(irqctrler2->addrs[0].address,
-							irqctrler2->addrs[0].size);
-				prom_get_irq_senses(senses, PMAC_OPENPIC2_OFFSET,
-						    PMAC_OPENPIC2_OFFSET+128);
-				OpenPIC_InitSenses = senses;
-				OpenPIC_NumInitSenses = 128;
-				openpic2_init(PMAC_OPENPIC2_OFFSET);
-
-				if (setup_irq(irqctrler2->intrs[0].line,
-					      &k2u3_cascade_action))
-					printk("Unable to get OpenPIC IRQ for cascade\n");
-			}
-#endif /* CONFIG_POWER4 */
-
-#ifdef CONFIG_XMON
-			{
-				struct device_node* pswitch;
-				int nmi_irq;
-
-				pswitch = find_devices("programmer-switch");
-				if (pswitch && pswitch->n_intrs) {
-					nmi_irq = pswitch->intrs[0].line;
-					openpic_init_nmi_irq(nmi_irq);
-					setup_irq(nmi_irq, &xmon_action);
-				}
-			}
-#endif	/* CONFIG_XMON */
-			return;
-		}
-		irqctrler = NULL;
-	}
-
-	/* Get the level/edge settings, assume if it's not
-	 * a Grand Central nor an OHare, then it's an Heathrow
-	 * (or Paddington).
-	 */
-	if (find_devices("gc"))
-		level_mask[0] = GC_LEVEL_MASK;
-	else if (find_devices("ohare")) {
-		level_mask[0] = OHARE_LEVEL_MASK;
-		/* We might have a second cascaded ohare */
-		level_mask[1] = OHARE_LEVEL_MASK;
-	} else {
-		level_mask[0] = HEATHROW_LEVEL_MASK;
-		level_mask[1] = 0;
-		/* We might have a second cascaded heathrow */
-		level_mask[2] = HEATHROW_LEVEL_MASK;
-		level_mask[3] = 0;
-	}
-
-	/*
-	 * G3 powermacs and 1999 G3 PowerBooks have 64 interrupts,
-	 * 1998 G3 Series PowerBooks have 128,
-	 * other powermacs have 32.
-	 * The combo ethernet/modem card for the Powerstar powerbooks
-	 * (2400/3400/3500, ohare based) has a second ohare chip
-	 * effectively making a total of 64.
-	 */
-	max_irqs = max_real_irqs = 32;
-	irqctrler = find_devices("mac-io");
-	if (irqctrler)
-	{
-		max_real_irqs = 64;
-		if (irqctrler->next)
-			max_irqs = 128;
-		else
-			max_irqs = 64;
-	}
-	for ( i = 0; i < max_real_irqs ; i++ )
-		irq_desc[i].handler = &pmac_pic;
-
-	/* get addresses of first controller */
-	if (irqctrler) {
-		if  (irqctrler->n_addrs > 0) {
-			addr = (unsigned long)
-				ioremap(irqctrler->addrs[0].address, 0x40);
-			for (i = 0; i < 2; ++i)
-				pmac_irq_hw[i] = (volatile struct pmac_irq_hw*)
-					(addr + (2 - i) * 0x10);
-		}
-
-		/* get addresses of second controller */
-		irqctrler = irqctrler->next;
-		if (irqctrler && irqctrler->n_addrs > 0) {
-			addr = (unsigned long)
-				ioremap(irqctrler->addrs[0].address, 0x40);
-			for (i = 2; i < 4; ++i)
-				pmac_irq_hw[i] = (volatile struct pmac_irq_hw*)
-					(addr + (4 - i) * 0x10);
-			irq_cascade = irqctrler->intrs[0].line;
-			if (device_is_compatible(irqctrler, "gatwick"))
-				pmac_fix_gatwick_interrupts(irqctrler, max_real_irqs);
-		}
-	} else {
-		/* older powermacs have a GC (grand central) or ohare at
-		   f3000000, with interrupt control registers at f3000020. */
-		addr = (unsigned long) ioremap(0xf3000000, 0x40);
-		pmac_irq_hw[0] = (volatile struct pmac_irq_hw *) (addr + 0x20);
-	}
-
-	/* PowerBooks 3400 and 3500 can have a second controller in a second
-	   ohare chip, on the combo ethernet/modem card */
-	if (machine_is_compatible("AAPL,3400/2400")
-	     || machine_is_compatible("AAPL,3500"))
-		irq_cascade = enable_second_ohare();
-
-	/* disable all interrupts in all controllers */
-	for (i = 0; i * 32 < max_irqs; ++i)
-		out_le32(&pmac_irq_hw[i]->enable, 0);
-	/* mark level interrupts */
-	for (i = 0; i < max_irqs; i++)
-		if (level_mask[i >> 5] & (1UL << (i & 0x1f)))
-			irq_desc[i].status = IRQ_LEVEL;
-
-	/* get interrupt line of secondary interrupt controller */
-	if (irq_cascade >= 0) {
-		printk(KERN_INFO "irq: secondary controller on irq %d\n",
-			(int)irq_cascade);
-		for ( i = max_real_irqs ; i < max_irqs ; i++ )
-			irq_desc[i].handler = &gatwick_pic;
-		setup_irq(irq_cascade, &gatwick_cascade_action);
-	}
-	printk("System has %d possible interrupts\n", max_irqs);
-	if (max_irqs != max_real_irqs)
-		printk(KERN_DEBUG "%d interrupts on main controller\n",
-			max_real_irqs);
-
-#ifdef CONFIG_XMON
-	setup_irq(20, &xmon_action);
-#endif	/* CONFIG_XMON */
-}
-
-#ifdef CONFIG_PM
-/*
- * These procedures are used in implementing sleep on the powerbooks.
- * sleep_save_intrs() saves the states of all interrupt enables
- * and disables all interrupts except for the nominated one.
- * sleep_restore_intrs() restores the states of all interrupt enables.
- */
-unsigned long sleep_save_mask[2];
-
-/* This used to be passed by the PMU driver but that link got
- * broken with the new driver model. We use this tweak for now...
- */
-static int pmacpic_find_viaint(void)
-{
-	int viaint = -1;
-
-#ifdef CONFIG_ADB_PMU
-	struct device_node *np;
-
-	if (pmu_get_model() != PMU_OHARE_BASED)
-		goto not_found;
-	np = of_find_node_by_name(NULL, "via-pmu");
-	if (np == NULL)
-		goto not_found;
-	viaint = np->intrs[0].line;
-#endif /* CONFIG_ADB_PMU */
-
-not_found:
-	return viaint;
-}
-
-static int pmacpic_suspend(struct sys_device *sysdev, pm_message_t state)
-{
-	int viaint = pmacpic_find_viaint();
-
-	sleep_save_mask[0] = ppc_cached_irq_mask[0];
-	sleep_save_mask[1] = ppc_cached_irq_mask[1];
-	ppc_cached_irq_mask[0] = 0;
-	ppc_cached_irq_mask[1] = 0;
-	if (viaint > 0)
-		set_bit(viaint, ppc_cached_irq_mask);
-	out_le32(&pmac_irq_hw[0]->enable, ppc_cached_irq_mask[0]);
-	if (max_real_irqs > 32)
-		out_le32(&pmac_irq_hw[1]->enable, ppc_cached_irq_mask[1]);
-	(void)in_le32(&pmac_irq_hw[0]->event);
-	/* make sure mask gets to controller before we return to caller */
-	mb();
-        (void)in_le32(&pmac_irq_hw[0]->enable);
-
-        return 0;
-}
-
-static int pmacpic_resume(struct sys_device *sysdev)
-{
-	int i;
-
-	out_le32(&pmac_irq_hw[0]->enable, 0);
-	if (max_real_irqs > 32)
-		out_le32(&pmac_irq_hw[1]->enable, 0);
-	mb();
-	for (i = 0; i < max_real_irqs; ++i)
-		if (test_bit(i, sleep_save_mask))
-			pmac_unmask_irq(i);
-
-	return 0;
-}
-
-#endif /* CONFIG_PM */
-
-static struct sysdev_class pmacpic_sysclass = {
-	set_kset_name("pmac_pic"),
-};
-
-static struct sys_device device_pmacpic = {
-	.id		= 0,
-	.cls		= &pmacpic_sysclass,
-};
-
-static struct sysdev_driver driver_pmacpic = {
-#ifdef CONFIG_PM
-	.suspend	= &pmacpic_suspend,
-	.resume		= &pmacpic_resume,
-#endif /* CONFIG_PM */
-};
-
-static int __init init_pmacpic_sysfs(void)
-{
-	if (max_irqs == 0)
-		return -ENODEV;
-
-	printk(KERN_DEBUG "Registering pmac pic with sysfs...\n");
-	sysdev_class_register(&pmacpic_sysclass);
-	sysdev_register(&device_pmacpic);
-	sysdev_driver_register(&pmacpic_sysclass, &driver_pmacpic);
-	return 0;
-}
-
-subsys_initcall(init_pmacpic_sysfs);
-
diff --git a/arch/ppc/platforms/pmac_pic.h b/arch/ppc/platforms/pmac_pic.h
deleted file mode 100644
index 664103dfeef..00000000000
--- a/arch/ppc/platforms/pmac_pic.h
+++ /dev/null
@@ -1,11 +0,0 @@
-#ifndef __PPC_PLATFORMS_PMAC_PIC_H
-#define __PPC_PLATFORMS_PMAC_PIC_H
-
-#include <linux/irq.h>
-
-extern struct hw_interrupt_type pmac_pic;
-
-void pmac_pic_init(void);
-int pmac_get_irq(struct pt_regs *regs);
-
-#endif /* __PPC_PLATFORMS_PMAC_PIC_H */
diff --git a/arch/ppc/platforms/pmac_setup.c b/arch/ppc/platforms/pmac_setup.c
deleted file mode 100644
index 55d2beffe56..00000000000
--- a/arch/ppc/platforms/pmac_setup.c
+++ /dev/null
@@ -1,745 +0,0 @@
-/*
- *  arch/ppc/platforms/setup.c
- *
- *  PowerPC version
- *    Copyright (C) 1995-1996 Gary Thomas (gdt@linuxppc.org)
- *
- *  Adapted for Power Macintosh by Paul Mackerras
- *    Copyright (C) 1996 Paul Mackerras (paulus@cs.anu.edu.au)
- *
- *  Derived from "arch/alpha/kernel/setup.c"
- *    Copyright (C) 1995 Linus Torvalds
- *
- *  Maintained by Benjamin Herrenschmidt (benh@kernel.crashing.org)
- *
- *  This program is free software; you can redistribute it and/or
- *  modify it under the terms of the GNU General Public License
- *  as published by the Free Software Foundation; either version
- *  2 of the License, or (at your option) any later version.
- *
- */
-
-/*
- * bootup setup stuff..
- */
-
-#include <linux/config.h>
-#include <linux/init.h>
-#include <linux/errno.h>
-#include <linux/sched.h>
-#include <linux/kernel.h>
-#include <linux/mm.h>
-#include <linux/stddef.h>
-#include <linux/unistd.h>
-#include <linux/ptrace.h>
-#include <linux/slab.h>
-#include <linux/user.h>
-#include <linux/a.out.h>
-#include <linux/tty.h>
-#include <linux/string.h>
-#include <linux/delay.h>
-#include <linux/ioport.h>
-#include <linux/major.h>
-#include <linux/initrd.h>
-#include <linux/vt_kern.h>
-#include <linux/console.h>
-#include <linux/ide.h>
-#include <linux/pci.h>
-#include <linux/adb.h>
-#include <linux/cuda.h>
-#include <linux/pmu.h>
-#include <linux/seq_file.h>
-#include <linux/root_dev.h>
-#include <linux/bitops.h>
-#include <linux/suspend.h>
-
-#include <asm/reg.h>
-#include <asm/sections.h>
-#include <asm/prom.h>
-#include <asm/system.h>
-#include <asm/pgtable.h>
-#include <asm/io.h>
-#include <asm/pci-bridge.h>
-#include <asm/ohare.h>
-#include <asm/mediabay.h>
-#include <asm/machdep.h>
-#include <asm/dma.h>
-#include <asm/bootx.h>
-#include <asm/cputable.h>
-#include <asm/btext.h>
-#include <asm/pmac_feature.h>
-#include <asm/time.h>
-#include <asm/of_device.h>
-#include <asm/mmu_context.h>
-
-#include "pmac_pic.h"
-#include "mem_pieces.h"
-
-#undef SHOW_GATWICK_IRQS
-
-extern long pmac_time_init(void);
-extern unsigned long pmac_get_rtc_time(void);
-extern int pmac_set_rtc_time(unsigned long nowtime);
-extern void pmac_read_rtc_time(void);
-extern void pmac_calibrate_decr(void);
-extern void pmac_pcibios_fixup(void);
-extern void pmac_find_bridges(void);
-extern unsigned long pmac_ide_get_base(int index);
-extern void pmac_ide_init_hwif_ports(hw_regs_t *hw,
-	unsigned long data_port, unsigned long ctrl_port, int *irq);
-
-extern void pmac_nvram_update(void);
-extern unsigned char pmac_nvram_read_byte(int addr);
-extern void pmac_nvram_write_byte(int addr, unsigned char val);
-extern int pmac_pci_enable_device_hook(struct pci_dev *dev, int initial);
-extern void pmac_pcibios_after_init(void);
-extern int of_show_percpuinfo(struct seq_file *m, int i);
-
-struct device_node *memory_node;
-
-unsigned char drive_info;
-
-int ppc_override_l2cr = 0;
-int ppc_override_l2cr_value;
-int has_l2cache = 0;
-
-static int current_root_goodness = -1;
-
-extern int pmac_newworld;
-
-#define DEFAULT_ROOT_DEVICE Root_SDA1	/* sda1 - slightly silly choice */
-
-extern void zs_kgdb_hook(int tty_num);
-static void ohare_init(void);
-#ifdef CONFIG_BOOTX_TEXT
-static void pmac_progress(char *s, unsigned short hex);
-#endif
-
-sys_ctrler_t sys_ctrler = SYS_CTRLER_UNKNOWN;
-
-#ifdef CONFIG_SMP
-extern struct smp_ops_t psurge_smp_ops;
-extern struct smp_ops_t core99_smp_ops;
-#endif /* CONFIG_SMP */
-
-static int
-pmac_show_cpuinfo(struct seq_file *m)
-{
-	struct device_node *np;
-	char *pp;
-	int plen;
-	int mbmodel = pmac_call_feature(PMAC_FTR_GET_MB_INFO,
-		NULL, PMAC_MB_INFO_MODEL, 0);
-	unsigned int mbflags = (unsigned int)pmac_call_feature(PMAC_FTR_GET_MB_INFO,
-		NULL, PMAC_MB_INFO_FLAGS, 0);
-	char* mbname;
-
-	if (pmac_call_feature(PMAC_FTR_GET_MB_INFO, NULL, PMAC_MB_INFO_NAME, (int)&mbname) != 0)
-		mbname = "Unknown";
-
-	/* find motherboard type */
-	seq_printf(m, "machine\t\t: ");
-	np = find_devices("device-tree");
-	if (np != NULL) {
-		pp = (char *) get_property(np, "model", NULL);
-		if (pp != NULL)
-			seq_printf(m, "%s\n", pp);
-		else
-			seq_printf(m, "PowerMac\n");
-		pp = (char *) get_property(np, "compatible", &plen);
-		if (pp != NULL) {
-			seq_printf(m, "motherboard\t:");
-			while (plen > 0) {
-				int l = strlen(pp) + 1;
-				seq_printf(m, " %s", pp);
-				plen -= l;
-				pp += l;
-			}
-			seq_printf(m, "\n");
-		}
-	} else
-		seq_printf(m, "PowerMac\n");
-
-	/* print parsed model */
-	seq_printf(m, "detected as\t: %d (%s)\n", mbmodel, mbname);
-	seq_printf(m, "pmac flags\t: %08x\n", mbflags);
-
-	/* find l2 cache info */
-	np = find_devices("l2-cache");
-	if (np == 0)
-		np = find_type_devices("cache");
-	if (np != 0) {
-		unsigned int *ic = (unsigned int *)
-			get_property(np, "i-cache-size", NULL);
-		unsigned int *dc = (unsigned int *)
-			get_property(np, "d-cache-size", NULL);
-		seq_printf(m, "L2 cache\t:");
-		has_l2cache = 1;
-		if (get_property(np, "cache-unified", NULL) != 0 && dc) {
-			seq_printf(m, " %dK unified", *dc / 1024);
-		} else {
-			if (ic)
-				seq_printf(m, " %dK instruction", *ic / 1024);
-			if (dc)
-				seq_printf(m, "%s %dK data",
-					   (ic? " +": ""), *dc / 1024);
-		}
-		pp = get_property(np, "ram-type", NULL);
-		if (pp)
-			seq_printf(m, " %s", pp);
-		seq_printf(m, "\n");
-	}
-
-	/* find ram info */
-	np = find_devices("memory");
-	if (np != 0) {
-		int n;
-		struct reg_property *reg = (struct reg_property *)
-			get_property(np, "reg", &n);
-
-		if (reg != 0) {
-			unsigned long total = 0;
-
-			for (n /= sizeof(struct reg_property); n > 0; --n)
-				total += (reg++)->size;
-			seq_printf(m, "memory\t\t: %luMB\n", total >> 20);
-		}
-	}
-
-	/* Checks "l2cr-value" property in the registry */
-	np = find_devices("cpus");
-	if (np == 0)
-		np = find_type_devices("cpu");
-	if (np != 0) {
-		unsigned int *l2cr = (unsigned int *)
-			get_property(np, "l2cr-value", NULL);
-		if (l2cr != 0) {
-			seq_printf(m, "l2cr override\t: 0x%x\n", *l2cr);
-		}
-	}
-
-	/* Indicate newworld/oldworld */
-	seq_printf(m, "pmac-generation\t: %s\n",
-		   pmac_newworld ? "NewWorld" : "OldWorld");
-
-
-	return 0;
-}
-
-static int
-pmac_show_percpuinfo(struct seq_file *m, int i)
-{
-#ifdef CONFIG_CPU_FREQ_PMAC
-	extern unsigned int pmac_get_one_cpufreq(int i);
-	unsigned int freq = pmac_get_one_cpufreq(i);
-	if (freq != 0) {
-		seq_printf(m, "clock\t\t: %dMHz\n", freq/1000);
-		return 0;
-	}
-#endif /* CONFIG_CPU_FREQ_PMAC */
-	return of_show_percpuinfo(m, i);
-}
-
-static volatile u32 *sysctrl_regs;
-
-void __init
-pmac_setup_arch(void)
-{
-	struct device_node *cpu;
-	int *fp;
-	unsigned long pvr;
-
-	pvr = PVR_VER(mfspr(SPRN_PVR));
-
-	/* Set loops_per_jiffy to a half-way reasonable value,
-	   for use until calibrate_delay gets called. */
-	cpu = find_type_devices("cpu");
-	if (cpu != 0) {
-		fp = (int *) get_property(cpu, "clock-frequency", NULL);
-		if (fp != 0) {
-			if (pvr == 4 || pvr >= 8)
-				/* 604, G3, G4 etc. */
-				loops_per_jiffy = *fp / HZ;
-			else
-				/* 601, 603, etc. */
-				loops_per_jiffy = *fp / (2*HZ);
-		} else
-			loops_per_jiffy = 50000000 / HZ;
-	}
-
-	/* this area has the CPU identification register
-	   and some registers used by smp boards */
-	sysctrl_regs = (volatile u32 *) ioremap(0xf8000000, 0x1000);
-	ohare_init();
-
-	/* Lookup PCI hosts */
-	pmac_find_bridges();
-
-	/* Checks "l2cr-value" property in the registry */
-	if (cpu_has_feature(CPU_FTR_L2CR)) {
-		struct device_node *np = find_devices("cpus");
-		if (np == 0)
-			np = find_type_devices("cpu");
-		if (np != 0) {
-			unsigned int *l2cr = (unsigned int *)
-				get_property(np, "l2cr-value", NULL);
-			if (l2cr != 0) {
-				ppc_override_l2cr = 1;
-				ppc_override_l2cr_value = *l2cr;
-				_set_L2CR(0);
-				_set_L2CR(ppc_override_l2cr_value);
-			}
-		}
-	}
-
-	if (ppc_override_l2cr)
-		printk(KERN_INFO "L2CR overriden (0x%x), backside cache is %s\n",
-			ppc_override_l2cr_value, (ppc_override_l2cr_value & 0x80000000)
-				? "enabled" : "disabled");
-
-#ifdef CONFIG_KGDB
-	zs_kgdb_hook(0);
-#endif
-
-#ifdef CONFIG_ADB_CUDA
-	find_via_cuda();
-#else
-	if (find_devices("via-cuda")) {
-		printk("WARNING ! Your machine is Cuda based but your kernel\n");
-		printk("          wasn't compiled with CONFIG_ADB_CUDA option !\n");
-	}
-#endif
-#ifdef CONFIG_ADB_PMU
-	find_via_pmu();
-#else
-	if (find_devices("via-pmu")) {
-		printk("WARNING ! Your machine is PMU based but your kernel\n");
-		printk("          wasn't compiled with CONFIG_ADB_PMU option !\n");
-	}
-#endif
-#ifdef CONFIG_NVRAM
-	pmac_nvram_init();
-#endif
-#ifdef CONFIG_BLK_DEV_INITRD
-	if (initrd_start)
-		ROOT_DEV = Root_RAM0;
-	else
-#endif
-		ROOT_DEV = DEFAULT_ROOT_DEVICE;
-
-#ifdef CONFIG_SMP
-	/* Check for Core99 */
-	if (find_devices("uni-n") || find_devices("u3"))
-		smp_ops = &core99_smp_ops;
-	else
-		smp_ops = &psurge_smp_ops;
-#endif /* CONFIG_SMP */
-
-	pci_create_OF_bus_map();
-}
-
-static void __init ohare_init(void)
-{
-	/*
-	 * Turn on the L2 cache.
-	 * We assume that we have a PSX memory controller iff
-	 * we have an ohare I/O controller.
-	 */
-	if (find_devices("ohare") != NULL) {
-		if (((sysctrl_regs[2] >> 24) & 0xf) >= 3) {
-			if (sysctrl_regs[4] & 0x10)
-				sysctrl_regs[4] |= 0x04000020;
-			else
-				sysctrl_regs[4] |= 0x04000000;
-			if(has_l2cache)
-				printk(KERN_INFO "Level 2 cache enabled\n");
-		}
-	}
-}
-
-extern char *bootpath;
-extern char *bootdevice;
-void *boot_host;
-int boot_target;
-int boot_part;
-extern dev_t boot_dev;
-
-#ifdef CONFIG_SCSI
-void __init
-note_scsi_host(struct device_node *node, void *host)
-{
-	int l;
-	char *p;
-
-	l = strlen(node->full_name);
-	if (bootpath != NULL && bootdevice != NULL
-	    && strncmp(node->full_name, bootdevice, l) == 0
-	    && (bootdevice[l] == '/' || bootdevice[l] == 0)) {
-		boot_host = host;
-		/*
-		 * There's a bug in OF 1.0.5.  (Why am I not surprised.)
-		 * If you pass a path like scsi/sd@1:0 to canon, it returns
-		 * something like /bandit@F2000000/gc@10/53c94@10000/sd@0,0
-		 * That is, the scsi target number doesn't get preserved.
-		 * So we pick the target number out of bootpath and use that.
-		 */
-		p = strstr(bootpath, "/sd@");
-		if (p != NULL) {
-			p += 4;
-			boot_target = simple_strtoul(p, NULL, 10);
-			p = strchr(p, ':');
-			if (p != NULL)
-				boot_part = simple_strtoul(p + 1, NULL, 10);
-		}
-	}
-}
-#endif
-
-#if defined(CONFIG_BLK_DEV_IDE) && defined(CONFIG_BLK_DEV_IDE_PMAC)
-static dev_t __init
-find_ide_boot(void)
-{
-	char *p;
-	int n;
-	dev_t __init pmac_find_ide_boot(char *bootdevice, int n);
-
-	if (bootdevice == NULL)
-		return 0;
-	p = strrchr(bootdevice, '/');
-	if (p == NULL)
-		return 0;
-	n = p - bootdevice;
-
-	return pmac_find_ide_boot(bootdevice, n);
-}
-#endif /* CONFIG_BLK_DEV_IDE && CONFIG_BLK_DEV_IDE_PMAC */
-
-static void __init
-find_boot_device(void)
-{
-#if defined(CONFIG_BLK_DEV_IDE) && defined(CONFIG_BLK_DEV_IDE_PMAC)
-	boot_dev = find_ide_boot();
-#endif
-}
-
-static int initializing = 1;
-/* TODO: Merge the suspend-to-ram with the common code !!!
- * currently, this is a stub implementation for suspend-to-disk
- * only
- */
-
-#ifdef CONFIG_SOFTWARE_SUSPEND
-
-static int pmac_pm_prepare(suspend_state_t state)
-{
-	printk(KERN_DEBUG "%s(%d)\n", __FUNCTION__, state);
-
-	return 0;
-}
-
-static int pmac_pm_enter(suspend_state_t state)
-{
-	printk(KERN_DEBUG "%s(%d)\n", __FUNCTION__, state);
-
-	/* Giveup the lazy FPU & vec so we don't have to back them
-	 * up from the low level code
-	 */
-	enable_kernel_fp();
-
-#ifdef CONFIG_ALTIVEC
-	if (cur_cpu_spec->cpu_features & CPU_FTR_ALTIVEC)
-		enable_kernel_altivec();
-#endif /* CONFIG_ALTIVEC */
-
-	return 0;
-}
-
-static int pmac_pm_finish(suspend_state_t state)
-{
-	printk(KERN_DEBUG "%s(%d)\n", __FUNCTION__, state);
-
-	/* Restore userland MMU context */
-	set_context(current->active_mm->context, current->active_mm->pgd);
-
-	return 0;
-}
-
-static struct pm_ops pmac_pm_ops = {
-	.pm_disk_mode	= PM_DISK_SHUTDOWN,
-	.prepare	= pmac_pm_prepare,
-	.enter		= pmac_pm_enter,
-	.finish		= pmac_pm_finish,
-};
-
-#endif /* CONFIG_SOFTWARE_SUSPEND */
-
-static int pmac_late_init(void)
-{
-	initializing = 0;
-#ifdef CONFIG_SOFTWARE_SUSPEND
-	pm_set_ops(&pmac_pm_ops);
-#endif /* CONFIG_SOFTWARE_SUSPEND */
-	return 0;
-}
-
-late_initcall(pmac_late_init);
-
-/* can't be __init - can be called whenever a disk is first accessed */
-void
-note_bootable_part(dev_t dev, int part, int goodness)
-{
-	static int found_boot = 0;
-	char *p;
-
-	if (!initializing)
-		return;
-	if ((goodness <= current_root_goodness) &&
-	    ROOT_DEV != DEFAULT_ROOT_DEVICE)
-		return;
-	p = strstr(saved_command_line, "root=");
-	if (p != NULL && (p == saved_command_line || p[-1] == ' '))
-		return;
-
-	if (!found_boot) {
-		find_boot_device();
-		found_boot = 1;
-	}
-	if (!boot_dev || dev == boot_dev) {
-		ROOT_DEV = dev + part;
-		boot_dev = 0;
-		current_root_goodness = goodness;
-	}
-}
-
-static void
-pmac_restart(char *cmd)
-{
-#ifdef CONFIG_ADB_CUDA
-	struct adb_request req;
-#endif /* CONFIG_ADB_CUDA */
-
-	switch (sys_ctrler) {
-#ifdef CONFIG_ADB_CUDA
-	case SYS_CTRLER_CUDA:
-		cuda_request(&req, NULL, 2, CUDA_PACKET,
-			     CUDA_RESET_SYSTEM);
-		for (;;)
-			cuda_poll();
-		break;
-#endif /* CONFIG_ADB_CUDA */
-#ifdef CONFIG_ADB_PMU
-	case SYS_CTRLER_PMU:
-		pmu_restart();
-		break;
-#endif /* CONFIG_ADB_PMU */
-	default: ;
-	}
-}
-
-static void
-pmac_power_off(void)
-{
-#ifdef CONFIG_ADB_CUDA
-	struct adb_request req;
-#endif /* CONFIG_ADB_CUDA */
-
-	switch (sys_ctrler) {
-#ifdef CONFIG_ADB_CUDA
-	case SYS_CTRLER_CUDA:
-		cuda_request(&req, NULL, 2, CUDA_PACKET,
-			     CUDA_POWERDOWN);
-		for (;;)
-			cuda_poll();
-		break;
-#endif /* CONFIG_ADB_CUDA */
-#ifdef CONFIG_ADB_PMU
-	case SYS_CTRLER_PMU:
-		pmu_shutdown();
-		break;
-#endif /* CONFIG_ADB_PMU */
-	default: ;
-	}
-}
-
-static void
-pmac_halt(void)
-{
-   pmac_power_off();
-}
-
-/*
- * Read in a property describing some pieces of memory.
- */
-
-static int __init
-get_mem_prop(char *name, struct mem_pieces *mp)
-{
-	struct reg_property *rp;
-	int i, s;
-	unsigned int *ip;
-	int nac = prom_n_addr_cells(memory_node);
-	int nsc = prom_n_size_cells(memory_node);
-
-	ip = (unsigned int *) get_property(memory_node, name, &s);
-	if (ip == NULL) {
-		printk(KERN_ERR "error: couldn't get %s property on /memory\n",
-		       name);
-		return 0;
-	}
-	s /= (nsc + nac) * 4;
-	rp = mp->regions;
-	for (i = 0; i < s; ++i, ip += nac+nsc) {
-		if (nac >= 2 && ip[nac-2] != 0)
-			continue;
-		rp->address = ip[nac-1];
-		if (nsc >= 2 && ip[nac+nsc-2] != 0)
-			rp->size = ~0U;
-		else
-			rp->size = ip[nac+nsc-1];
-		++rp;
-	}
-	mp->n_regions = rp - mp->regions;
-
-	/* Make sure the pieces are sorted. */
-	mem_pieces_sort(mp);
-	mem_pieces_coalesce(mp);
-	return 1;
-}
-
-/*
- * On systems with Open Firmware, collect information about
- * physical RAM and which pieces are already in use.
- * At this point, we have (at least) the first 8MB mapped with a BAT.
- * Our text, data, bss use something over 1MB, starting at 0.
- * Open Firmware may be using 1MB at the 4MB point.
- */
-unsigned long __init
-pmac_find_end_of_memory(void)
-{
-	unsigned long a, total;
-	struct mem_pieces phys_mem;
-
-	/*
-	 * Find out where physical memory is, and check that it
-	 * starts at 0 and is contiguous.  It seems that RAM is
-	 * always physically contiguous on Power Macintoshes.
-	 *
-	 * Supporting discontiguous physical memory isn't hard,
-	 * it just makes the virtual <-> physical mapping functions
-	 * more complicated (or else you end up wasting space
-	 * in mem_map).
-	 */
-	memory_node = find_devices("memory");
-	if (memory_node == NULL || !get_mem_prop("reg", &phys_mem)
-	    || phys_mem.n_regions == 0)
-		panic("No RAM??");
-	a = phys_mem.regions[0].address;
-	if (a != 0)
-		panic("RAM doesn't start at physical address 0");
-	total = phys_mem.regions[0].size;
-
-	if (phys_mem.n_regions > 1) {
-		printk("RAM starting at 0x%x is not contiguous\n",
-		       phys_mem.regions[1].address);
-		printk("Using RAM from 0 to 0x%lx\n", total-1);
-	}
-
-	return total;
-}
-
-void __init
-pmac_init(unsigned long r3, unsigned long r4, unsigned long r5,
-	  unsigned long r6, unsigned long r7)
-{
-	/* isa_io_base gets set in pmac_find_bridges */
-	isa_mem_base = PMAC_ISA_MEM_BASE;
-	pci_dram_offset = PMAC_PCI_DRAM_OFFSET;
-	ISA_DMA_THRESHOLD = ~0L;
-	DMA_MODE_READ = 1;
-	DMA_MODE_WRITE = 2;
-
-	ppc_md.setup_arch     = pmac_setup_arch;
-	ppc_md.show_cpuinfo   = pmac_show_cpuinfo;
-	ppc_md.show_percpuinfo = pmac_show_percpuinfo;
-	ppc_md.init_IRQ       = pmac_pic_init;
-	ppc_md.get_irq        = pmac_get_irq; /* Changed later on ... */
-
-	ppc_md.pcibios_fixup  = pmac_pcibios_fixup;
-	ppc_md.pcibios_enable_device_hook = pmac_pci_enable_device_hook;
-	ppc_md.pcibios_after_init = pmac_pcibios_after_init;
-	ppc_md.phys_mem_access_prot = pci_phys_mem_access_prot;
-
-	ppc_md.restart        = pmac_restart;
-	ppc_md.power_off      = pmac_power_off;
-	ppc_md.halt           = pmac_halt;
-
-	ppc_md.time_init      = pmac_time_init;
-	ppc_md.set_rtc_time   = pmac_set_rtc_time;
-	ppc_md.get_rtc_time   = pmac_get_rtc_time;
-	ppc_md.calibrate_decr = pmac_calibrate_decr;
-
-	ppc_md.find_end_of_memory = pmac_find_end_of_memory;
-
-	ppc_md.feature_call   = pmac_do_feature_call;
-
-#if defined(CONFIG_BLK_DEV_IDE) || defined(CONFIG_BLK_DEV_IDE_MODULE)
-#ifdef CONFIG_BLK_DEV_IDE_PMAC
-        ppc_ide_md.ide_init_hwif	= pmac_ide_init_hwif_ports;
-        ppc_ide_md.default_io_base	= pmac_ide_get_base;
-#endif /* CONFIG_BLK_DEV_IDE_PMAC */
-#endif /* defined(CONFIG_BLK_DEV_IDE) || defined(CONFIG_BLK_DEV_IDE_MODULE) */
-
-#ifdef CONFIG_BOOTX_TEXT
-	ppc_md.progress = pmac_progress;
-#endif /* CONFIG_BOOTX_TEXT */
-
-	if (ppc_md.progress) ppc_md.progress("pmac_init(): exit", 0);
-
-}
-
-#ifdef CONFIG_BOOTX_TEXT
-static void __init
-pmac_progress(char *s, unsigned short hex)
-{
-	if (boot_text_mapped) {
-		btext_drawstring(s);
-		btext_drawchar('\n');
-	}
-}
-#endif /* CONFIG_BOOTX_TEXT */
-
-static int __init
-pmac_declare_of_platform_devices(void)
-{
-	struct device_node *np;
-
-	np = find_devices("uni-n");
-	if (np) {
-		for (np = np->child; np != NULL; np = np->sibling)
-			if (strncmp(np->name, "i2c", 3) == 0) {
-				of_platform_device_create(np, "uni-n-i2c",
-							  NULL);
-				break;
-			}
-	}
-	np = find_devices("u3");
-	if (np) {
-		for (np = np->child; np != NULL; np = np->sibling)
-			if (strncmp(np->name, "i2c", 3) == 0) {
-				of_platform_device_create(np, "u3-i2c",
-							  NULL);
-				break;
-			}
-	}
-
-	np = find_devices("valkyrie");
-	if (np)
-		of_platform_device_create(np, "valkyrie", NULL);
-	np = find_devices("platinum");
-	if (np)
-		of_platform_device_create(np, "platinum", NULL);
-
-	return 0;
-}
-
-device_initcall(pmac_declare_of_platform_devices);
diff --git a/arch/ppc/platforms/pmac_sleep.S b/arch/ppc/platforms/pmac_sleep.S
deleted file mode 100644
index 22b113d19b2..00000000000
--- a/arch/ppc/platforms/pmac_sleep.S
+++ /dev/null
@@ -1,396 +0,0 @@
-/*
- * This file contains sleep low-level functions for PowerBook G3.
- *    Copyright (C) 1999 Benjamin Herrenschmidt (benh@kernel.crashing.org)
- *    and Paul Mackerras (paulus@samba.org).
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License
- * as published by the Free Software Foundation; either version
- * 2 of the License, or (at your option) any later version.
- *
- */
-
-#include <linux/config.h>
-#include <asm/processor.h>
-#include <asm/page.h>
-#include <asm/ppc_asm.h>
-#include <asm/cputable.h>
-#include <asm/cache.h>
-#include <asm/thread_info.h>
-#include <asm/asm-offsets.h>
-
-#define MAGIC	0x4c617273	/* 'Lars' */
-
-/*
- * Structure for storing CPU registers on the stack.
- */
-#define SL_SP		0
-#define SL_PC		4
-#define SL_MSR		8
-#define SL_SDR1		0xc
-#define SL_SPRG0	0x10	/* 4 sprg's */
-#define SL_DBAT0	0x20
-#define SL_IBAT0	0x28
-#define SL_DBAT1	0x30
-#define SL_IBAT1	0x38
-#define SL_DBAT2	0x40
-#define SL_IBAT2	0x48
-#define SL_DBAT3	0x50
-#define SL_IBAT3	0x58
-#define SL_TB		0x60
-#define SL_R2		0x68
-#define SL_CR		0x6c
-#define SL_R12		0x70	/* r12 to r31 */
-#define SL_SIZE		(SL_R12 + 80)
-
-	.section .text
-	.align	5
-
-#if defined(CONFIG_PM) || defined(CONFIG_CPU_FREQ_PMAC)
-
-/* This gets called by via-pmu.c late during the sleep process.
- * The PMU was already send the sleep command and will shut us down
- * soon. We need to save all that is needed and setup the wakeup
- * vector that will be called by the ROM on wakeup
- */
-_GLOBAL(low_sleep_handler)
-#ifndef CONFIG_6xx
-	blr
-#else
-	mflr	r0
-	stw	r0,4(r1)
-	stwu	r1,-SL_SIZE(r1)
-	mfcr	r0
-	stw	r0,SL_CR(r1)
-	stw	r2,SL_R2(r1)
-	stmw	r12,SL_R12(r1)
-
-	/* Save MSR & SDR1 */
-	mfmsr	r4
-	stw	r4,SL_MSR(r1)
-	mfsdr1	r4
-	stw	r4,SL_SDR1(r1)
-
-	/* Get a stable timebase and save it */
-1:	mftbu	r4
-	stw	r4,SL_TB(r1)
-	mftb	r5
-	stw	r5,SL_TB+4(r1)
-	mftbu	r3
-	cmpw	r3,r4
-	bne	1b
-
-	/* Save SPRGs */
-	mfsprg	r4,0
-	stw	r4,SL_SPRG0(r1)
-	mfsprg	r4,1
-	stw	r4,SL_SPRG0+4(r1)
-	mfsprg	r4,2
-	stw	r4,SL_SPRG0+8(r1)
-	mfsprg	r4,3
-	stw	r4,SL_SPRG0+12(r1)
-
-	/* Save BATs */
-	mfdbatu	r4,0
-	stw	r4,SL_DBAT0(r1)
-	mfdbatl	r4,0
-	stw	r4,SL_DBAT0+4(r1)
-	mfdbatu	r4,1
-	stw	r4,SL_DBAT1(r1)
-	mfdbatl	r4,1
-	stw	r4,SL_DBAT1+4(r1)
-	mfdbatu	r4,2
-	stw	r4,SL_DBAT2(r1)
-	mfdbatl	r4,2
-	stw	r4,SL_DBAT2+4(r1)
-	mfdbatu	r4,3
-	stw	r4,SL_DBAT3(r1)
-	mfdbatl	r4,3
-	stw	r4,SL_DBAT3+4(r1)
-	mfibatu	r4,0
-	stw	r4,SL_IBAT0(r1)
-	mfibatl	r4,0
-	stw	r4,SL_IBAT0+4(r1)
-	mfibatu	r4,1
-	stw	r4,SL_IBAT1(r1)
-	mfibatl	r4,1
-	stw	r4,SL_IBAT1+4(r1)
-	mfibatu	r4,2
-	stw	r4,SL_IBAT2(r1)
-	mfibatl	r4,2
-	stw	r4,SL_IBAT2+4(r1)
-	mfibatu	r4,3
-	stw	r4,SL_IBAT3(r1)
-	mfibatl	r4,3
-	stw	r4,SL_IBAT3+4(r1)
-
-	/* Backup various CPU config stuffs */
-	bl	__save_cpu_setup
-
-	/* The ROM can wake us up via 2 different vectors:
-	 *  - On wallstreet & lombard, we must write a magic
-	 *    value 'Lars' at address 4 and a pointer to a
-	 *    memory location containing the PC to resume from
-	 *    at address 0.
-	 *  - On Core99, we must store the wakeup vector at
-	 *    address 0x80 and eventually it's parameters
-	 *    at address 0x84. I've have some trouble with those
-	 *    parameters however and I no longer use them.
-	 */
-	lis	r5,grackle_wake_up@ha
-	addi	r5,r5,grackle_wake_up@l
-	tophys(r5,r5)
-	stw	r5,SL_PC(r1)
-	lis	r4,KERNELBASE@h
-	tophys(r5,r1)
-	addi	r5,r5,SL_PC
-	lis	r6,MAGIC@ha
-	addi	r6,r6,MAGIC@l
-	stw	r5,0(r4)
-	stw	r6,4(r4)
-	/* Setup stuffs at 0x80-0x84 for Core99 */
-	lis	r3,core99_wake_up@ha
-	addi	r3,r3,core99_wake_up@l
-	tophys(r3,r3)
-	stw	r3,0x80(r4)
-	stw	r5,0x84(r4)
-	/* Store a pointer to our backup storage into
-	 * a kernel global
-	 */
-	lis r3,sleep_storage@ha
-	addi r3,r3,sleep_storage@l
-	stw r5,0(r3)
-
-	.globl	low_cpu_die
-low_cpu_die:
-	/* Flush & disable all caches */
-	bl	flush_disable_caches
-
-	/* Turn off data relocation. */
-	mfmsr	r3		/* Save MSR in r7 */
-	rlwinm	r3,r3,0,28,26	/* Turn off DR bit */
-	sync
-	mtmsr	r3
-	isync
-
-BEGIN_FTR_SECTION
-	/* Flush any pending L2 data prefetches to work around HW bug */
-	sync
-	lis	r3,0xfff0
-	lwz	r0,0(r3)	/* perform cache-inhibited load to ROM */
-	sync			/* (caches are disabled at this point) */
-END_FTR_SECTION_IFSET(CPU_FTR_SPEC7450)
-
-/*
- * Set the HID0 and MSR for sleep.
- */
-	mfspr	r2,SPRN_HID0
-	rlwinm	r2,r2,0,10,7	/* clear doze, nap */
-	oris	r2,r2,HID0_SLEEP@h
-	sync
-	isync
-	mtspr	SPRN_HID0,r2
-	sync
-
-/* This loop puts us back to sleep in case we have a spurrious
- * wakeup so that the host bridge properly stays asleep. The
- * CPU will be turned off, either after a known time (about 1
- * second) on wallstreet & lombard, or as soon as the CPU enters
- * SLEEP mode on core99
- */
-	mfmsr	r2
-	oris	r2,r2,MSR_POW@h
-1:	sync
-	mtmsr	r2
-	isync
-	b	1b
-
-/*
- * Here is the resume code.
- */
-
-
-/*
- * Core99 machines resume here
- * r4 has the physical address of SL_PC(sp) (unused)
- */
-_GLOBAL(core99_wake_up)
-	/* Make sure HID0 no longer contains any sleep bit and that data cache
-	 * is disabled
-	 */
-	mfspr	r3,SPRN_HID0
-	rlwinm	r3,r3,0,11,7		/* clear SLEEP, NAP, DOZE bits */
-	rlwinm	3,r3,0,18,15		/* clear DCE, ICE */
-	mtspr	SPRN_HID0,r3
-	sync
-	isync
-
-	/* sanitize MSR */
-	mfmsr	r3
-	ori	r3,r3,MSR_EE|MSR_IP
-	xori	r3,r3,MSR_EE|MSR_IP
-	sync
-	isync
-	mtmsr	r3
-	sync
-	isync
-
-	/* Recover sleep storage */
-	lis	r3,sleep_storage@ha
-	addi	r3,r3,sleep_storage@l
-	tophys(r3,r3)
-	lwz	r1,0(r3)
-
-	/* Pass thru to older resume code ... */
-/*
- * Here is the resume code for older machines.
- * r1 has the physical address of SL_PC(sp).
- */
-
-grackle_wake_up:
-
-	/* Restore the kernel's segment registers before
-	 * we do any r1 memory access as we are not sure they
-	 * are in a sane state above the first 256Mb region
-	 */
-	li	r0,16		/* load up segment register values */
-	mtctr	r0		/* for context 0 */
-	lis	r3,0x2000	/* Ku = 1, VSID = 0 */
-	li	r4,0
-3:	mtsrin	r3,r4
-	addi	r3,r3,0x111	/* increment VSID */
-	addis	r4,r4,0x1000	/* address of next segment */
-	bdnz	3b
-	sync
-	isync
-
-	subi	r1,r1,SL_PC
-
-	/* Restore various CPU config stuffs */
-	bl	__restore_cpu_setup
-
-	/* Make sure all FPRs have been initialized */
-	bl	reloc_offset
-	bl	__init_fpu_registers
-
-	/* Invalidate & enable L1 cache, we don't care about
-	 * whatever the ROM may have tried to write to memory
-	 */
-	bl	__inval_enable_L1
-
-	/* Restore the BATs, and SDR1.  Then we can turn on the MMU. */
-	lwz	r4,SL_SDR1(r1)
-	mtsdr1	r4
-	lwz	r4,SL_SPRG0(r1)
-	mtsprg	0,r4
-	lwz	r4,SL_SPRG0+4(r1)
-	mtsprg	1,r4
-	lwz	r4,SL_SPRG0+8(r1)
-	mtsprg	2,r4
-	lwz	r4,SL_SPRG0+12(r1)
-	mtsprg	3,r4
-
-	lwz	r4,SL_DBAT0(r1)
-	mtdbatu	0,r4
-	lwz	r4,SL_DBAT0+4(r1)
-	mtdbatl	0,r4
-	lwz	r4,SL_DBAT1(r1)
-	mtdbatu	1,r4
-	lwz	r4,SL_DBAT1+4(r1)
-	mtdbatl	1,r4
-	lwz	r4,SL_DBAT2(r1)
-	mtdbatu	2,r4
-	lwz	r4,SL_DBAT2+4(r1)
-	mtdbatl	2,r4
-	lwz	r4,SL_DBAT3(r1)
-	mtdbatu	3,r4
-	lwz	r4,SL_DBAT3+4(r1)
-	mtdbatl	3,r4
-	lwz	r4,SL_IBAT0(r1)
-	mtibatu	0,r4
-	lwz	r4,SL_IBAT0+4(r1)
-	mtibatl	0,r4
-	lwz	r4,SL_IBAT1(r1)
-	mtibatu	1,r4
-	lwz	r4,SL_IBAT1+4(r1)
-	mtibatl	1,r4
-	lwz	r4,SL_IBAT2(r1)
-	mtibatu	2,r4
-	lwz	r4,SL_IBAT2+4(r1)
-	mtibatl	2,r4
-	lwz	r4,SL_IBAT3(r1)
-	mtibatu	3,r4
-	lwz	r4,SL_IBAT3+4(r1)
-	mtibatl	3,r4
-
-BEGIN_FTR_SECTION
-	li	r4,0
-	mtspr	SPRN_DBAT4U,r4
-	mtspr	SPRN_DBAT4L,r4
-	mtspr	SPRN_DBAT5U,r4
-	mtspr	SPRN_DBAT5L,r4
-	mtspr	SPRN_DBAT6U,r4
-	mtspr	SPRN_DBAT6L,r4
-	mtspr	SPRN_DBAT7U,r4
-	mtspr	SPRN_DBAT7L,r4
-	mtspr	SPRN_IBAT4U,r4
-	mtspr	SPRN_IBAT4L,r4
-	mtspr	SPRN_IBAT5U,r4
-	mtspr	SPRN_IBAT5L,r4
-	mtspr	SPRN_IBAT6U,r4
-	mtspr	SPRN_IBAT6L,r4
-	mtspr	SPRN_IBAT7U,r4
-	mtspr	SPRN_IBAT7L,r4
-END_FTR_SECTION_IFSET(CPU_FTR_HAS_HIGH_BATS)
-
-	/* Flush all TLBs */
-	lis	r4,0x1000
-1:	addic.	r4,r4,-0x1000
-	tlbie	r4
-	blt	1b
-	sync
-
-	/* restore the MSR and turn on the MMU */
-	lwz	r3,SL_MSR(r1)
-	bl	turn_on_mmu
-
-	/* get back the stack pointer */
-	tovirt(r1,r1)
-
-	/* Restore TB */
-	li	r3,0
-	mttbl	r3
-	lwz	r3,SL_TB(r1)
-	lwz	r4,SL_TB+4(r1)
-	mttbu	r3
-	mttbl	r4
-
-	/* Restore the callee-saved registers and return */
-	lwz	r0,SL_CR(r1)
-	mtcr	r0
-	lwz	r2,SL_R2(r1)
-	lmw	r12,SL_R12(r1)
-	addi	r1,r1,SL_SIZE
-	lwz	r0,4(r1)
-	mtlr	r0
-	blr
-
-turn_on_mmu:
-	mflr	r4
-	tovirt(r4,r4)
-	mtsrr0	r4
-	mtsrr1	r3
-	sync
-	isync
-	rfi
-
-#endif /* defined(CONFIG_PM) || defined(CONFIG_CPU_FREQ) */
-
-	.section .data
-	.balign	L1_CACHE_BYTES
-sleep_storage:
-	.long 0
-	.balign	L1_CACHE_BYTES, 0
-
-#endif /* CONFIG_6xx */
-	.section .text
diff --git a/arch/ppc/platforms/pmac_smp.c b/arch/ppc/platforms/pmac_smp.c
deleted file mode 100644
index 26ff26238f0..00000000000
--- a/arch/ppc/platforms/pmac_smp.c
+++ /dev/null
@@ -1,692 +0,0 @@
-/*
- * SMP support for power macintosh.
- *
- * We support both the old "powersurge" SMP architecture
- * and the current Core99 (G4 PowerMac) machines.
- *
- * Note that we don't support the very first rev. of
- * Apple/DayStar 2 CPUs board, the one with the funky
- * watchdog. Hopefully, none of these should be there except
- * maybe internally to Apple. I should probably still add some
- * code to detect this card though and disable SMP. --BenH.
- *
- * Support Macintosh G4 SMP by Troy Benjegerdes (hozer@drgw.net)
- * and Ben Herrenschmidt <benh@kernel.crashing.org>.
- *
- * Support for DayStar quad CPU cards
- * Copyright (C) XLR8, Inc. 1994-2000
- *
- *  This program is free software; you can redistribute it and/or
- *  modify it under the terms of the GNU General Public License
- *  as published by the Free Software Foundation; either version
- *  2 of the License, or (at your option) any later version.
- */
-#include <linux/config.h>
-#include <linux/kernel.h>
-#include <linux/sched.h>
-#include <linux/smp.h>
-#include <linux/smp_lock.h>
-#include <linux/interrupt.h>
-#include <linux/kernel_stat.h>
-#include <linux/delay.h>
-#include <linux/init.h>
-#include <linux/spinlock.h>
-#include <linux/errno.h>
-#include <linux/hardirq.h>
-#include <linux/cpu.h>
-
-#include <asm/ptrace.h>
-#include <asm/atomic.h>
-#include <asm/irq.h>
-#include <asm/page.h>
-#include <asm/pgtable.h>
-#include <asm/sections.h>
-#include <asm/io.h>
-#include <asm/prom.h>
-#include <asm/smp.h>
-#include <asm/residual.h>
-#include <asm/machdep.h>
-#include <asm/pmac_feature.h>
-#include <asm/time.h>
-#include <asm/open_pic.h>
-#include <asm/cacheflush.h>
-#include <asm/keylargo.h>
-
-/*
- * Powersurge (old powermac SMP) support.
- */
-
-extern void __secondary_start_pmac_0(void);
-
-/* Addresses for powersurge registers */
-#define HAMMERHEAD_BASE		0xf8000000
-#define HHEAD_CONFIG		0x90
-#define HHEAD_SEC_INTR		0xc0
-
-/* register for interrupting the primary processor on the powersurge */
-/* N.B. this is actually the ethernet ROM! */
-#define PSURGE_PRI_INTR		0xf3019000
-
-/* register for storing the start address for the secondary processor */
-/* N.B. this is the PCI config space address register for the 1st bridge */
-#define PSURGE_START		0xf2800000
-
-/* Daystar/XLR8 4-CPU card */
-#define PSURGE_QUAD_REG_ADDR	0xf8800000
-
-#define PSURGE_QUAD_IRQ_SET	0
-#define PSURGE_QUAD_IRQ_CLR	1
-#define PSURGE_QUAD_IRQ_PRIMARY	2
-#define PSURGE_QUAD_CKSTOP_CTL	3
-#define PSURGE_QUAD_PRIMARY_ARB	4
-#define PSURGE_QUAD_BOARD_ID	6
-#define PSURGE_QUAD_WHICH_CPU	7
-#define PSURGE_QUAD_CKSTOP_RDBK	8
-#define PSURGE_QUAD_RESET_CTL	11
-
-#define PSURGE_QUAD_OUT(r, v)	(out_8(quad_base + ((r) << 4) + 4, (v)))
-#define PSURGE_QUAD_IN(r)	(in_8(quad_base + ((r) << 4) + 4) & 0x0f)
-#define PSURGE_QUAD_BIS(r, v)	(PSURGE_QUAD_OUT((r), PSURGE_QUAD_IN(r) | (v)))
-#define PSURGE_QUAD_BIC(r, v)	(PSURGE_QUAD_OUT((r), PSURGE_QUAD_IN(r) & ~(v)))
-
-/* virtual addresses for the above */
-static volatile u8 __iomem *hhead_base;
-static volatile u8 __iomem *quad_base;
-static volatile u32 __iomem *psurge_pri_intr;
-static volatile u8 __iomem *psurge_sec_intr;
-static volatile u32 __iomem *psurge_start;
-
-/* values for psurge_type */
-#define PSURGE_NONE		-1
-#define PSURGE_DUAL		0
-#define PSURGE_QUAD_OKEE	1
-#define PSURGE_QUAD_COTTON	2
-#define PSURGE_QUAD_ICEGRASS	3
-
-/* what sort of powersurge board we have */
-static int psurge_type = PSURGE_NONE;
-
-/* L2 and L3 cache settings to pass from CPU0 to CPU1 */
-volatile static long int core99_l2_cache;
-volatile static long int core99_l3_cache;
-
-/* Timebase freeze GPIO */
-static unsigned int core99_tb_gpio;
-
-/* Sync flag for HW tb sync */
-static volatile int sec_tb_reset = 0;
-static unsigned int pri_tb_hi, pri_tb_lo;
-static unsigned int pri_tb_stamp;
-
-static void __devinit core99_init_caches(int cpu)
-{
-	if (!cpu_has_feature(CPU_FTR_L2CR))
-		return;
-
-	if (cpu == 0) {
-		core99_l2_cache = _get_L2CR();
-		printk("CPU0: L2CR is %lx\n", core99_l2_cache);
-	} else {
-		printk("CPU%d: L2CR was %lx\n", cpu, _get_L2CR());
-		_set_L2CR(0);
-		_set_L2CR(core99_l2_cache);
-		printk("CPU%d: L2CR set to %lx\n", cpu, core99_l2_cache);
-	}
-
-	if (!cpu_has_feature(CPU_FTR_L3CR))
-		return;
-
-	if (cpu == 0){
-		core99_l3_cache = _get_L3CR();
-		printk("CPU0: L3CR is %lx\n", core99_l3_cache);
-	} else {
-		printk("CPU%d: L3CR was %lx\n", cpu, _get_L3CR());
-		_set_L3CR(0);
-		_set_L3CR(core99_l3_cache);
-		printk("CPU%d: L3CR set to %lx\n", cpu, core99_l3_cache);
-	}
-}
-
-/*
- * Set and clear IPIs for powersurge.
- */
-static inline void psurge_set_ipi(int cpu)
-{
-	if (psurge_type == PSURGE_NONE)
-		return;
-	if (cpu == 0)
-		in_be32(psurge_pri_intr);
-	else if (psurge_type == PSURGE_DUAL)
-		out_8(psurge_sec_intr, 0);
-	else
-		PSURGE_QUAD_OUT(PSURGE_QUAD_IRQ_SET, 1 << cpu);
-}
-
-static inline void psurge_clr_ipi(int cpu)
-{
-	if (cpu > 0) {
-		switch(psurge_type) {
-		case PSURGE_DUAL:
-			out_8(psurge_sec_intr, ~0);
-		case PSURGE_NONE:
-			break;
-		default:
-			PSURGE_QUAD_OUT(PSURGE_QUAD_IRQ_CLR, 1 << cpu);
-		}
-	}
-}
-
-/*
- * On powersurge (old SMP powermac architecture) we don't have
- * separate IPIs for separate messages like openpic does.  Instead
- * we have a bitmap for each processor, where a 1 bit means that
- * the corresponding message is pending for that processor.
- * Ideally each cpu's entry would be in a different cache line.
- *  -- paulus.
- */
-static unsigned long psurge_smp_message[NR_CPUS];
-
-void psurge_smp_message_recv(struct pt_regs *regs)
-{
-	int cpu = smp_processor_id();
-	int msg;
-
-	/* clear interrupt */
-	psurge_clr_ipi(cpu);
-
-	if (num_online_cpus() < 2)
-		return;
-
-	/* make sure there is a message there */
-	for (msg = 0; msg < 4; msg++)
-		if (test_and_clear_bit(msg, &psurge_smp_message[cpu]))
-			smp_message_recv(msg, regs);
-}
-
-irqreturn_t psurge_primary_intr(int irq, void *d, struct pt_regs *regs)
-{
-	psurge_smp_message_recv(regs);
-	return IRQ_HANDLED;
-}
-
-static void smp_psurge_message_pass(int target, int msg)
-{
-	int i;
-
-	if (num_online_cpus() < 2)
-		return;
-
-	for (i = 0; i < NR_CPUS; i++) {
-		if (!cpu_online(i))
-			continue;
-		if (target == MSG_ALL
-		    || (target == MSG_ALL_BUT_SELF && i != smp_processor_id())
-		    || target == i) {
-			set_bit(msg, &psurge_smp_message[i]);
-			psurge_set_ipi(i);
-		}
-	}
-}
-
-/*
- * Determine a quad card presence. We read the board ID register, we
- * force the data bus to change to something else, and we read it again.
- * It it's stable, then the register probably exist (ugh !)
- */
-static int __init psurge_quad_probe(void)
-{
-	int type;
-	unsigned int i;
-
-	type = PSURGE_QUAD_IN(PSURGE_QUAD_BOARD_ID);
-	if (type < PSURGE_QUAD_OKEE || type > PSURGE_QUAD_ICEGRASS
-	    || type != PSURGE_QUAD_IN(PSURGE_QUAD_BOARD_ID))
-		return PSURGE_DUAL;
-
-	/* looks OK, try a slightly more rigorous test */
-	/* bogus is not necessarily cacheline-aligned,
-	   though I don't suppose that really matters.  -- paulus */
-	for (i = 0; i < 100; i++) {
-		volatile u32 bogus[8];
-		bogus[(0+i)%8] = 0x00000000;
-		bogus[(1+i)%8] = 0x55555555;
-		bogus[(2+i)%8] = 0xFFFFFFFF;
-		bogus[(3+i)%8] = 0xAAAAAAAA;
-		bogus[(4+i)%8] = 0x33333333;
-		bogus[(5+i)%8] = 0xCCCCCCCC;
-		bogus[(6+i)%8] = 0xCCCCCCCC;
-		bogus[(7+i)%8] = 0x33333333;
-		wmb();
-		asm volatile("dcbf 0,%0" : : "r" (bogus) : "memory");
-		mb();
-		if (type != PSURGE_QUAD_IN(PSURGE_QUAD_BOARD_ID))
-			return PSURGE_DUAL;
-	}
-	return type;
-}
-
-static void __init psurge_quad_init(void)
-{
-	int procbits;
-
-	if (ppc_md.progress) ppc_md.progress("psurge_quad_init", 0x351);
-	procbits = ~PSURGE_QUAD_IN(PSURGE_QUAD_WHICH_CPU);
-	if (psurge_type == PSURGE_QUAD_ICEGRASS)
-		PSURGE_QUAD_BIS(PSURGE_QUAD_RESET_CTL, procbits);
-	else
-		PSURGE_QUAD_BIC(PSURGE_QUAD_CKSTOP_CTL, procbits);
-	mdelay(33);
-	out_8(psurge_sec_intr, ~0);
-	PSURGE_QUAD_OUT(PSURGE_QUAD_IRQ_CLR, procbits);
-	PSURGE_QUAD_BIS(PSURGE_QUAD_RESET_CTL, procbits);
-	if (psurge_type != PSURGE_QUAD_ICEGRASS)
-		PSURGE_QUAD_BIS(PSURGE_QUAD_CKSTOP_CTL, procbits);
-	PSURGE_QUAD_BIC(PSURGE_QUAD_PRIMARY_ARB, procbits);
-	mdelay(33);
-	PSURGE_QUAD_BIC(PSURGE_QUAD_RESET_CTL, procbits);
-	mdelay(33);
-	PSURGE_QUAD_BIS(PSURGE_QUAD_PRIMARY_ARB, procbits);
-	mdelay(33);
-}
-
-static int __init smp_psurge_probe(void)
-{
-	int i, ncpus;
-
-	/* We don't do SMP on the PPC601 -- paulus */
-	if (PVR_VER(mfspr(SPRN_PVR)) == 1)
-		return 1;
-
-	/*
-	 * The powersurge cpu board can be used in the generation
-	 * of powermacs that have a socket for an upgradeable cpu card,
-	 * including the 7500, 8500, 9500, 9600.
-	 * The device tree doesn't tell you if you have 2 cpus because
-	 * OF doesn't know anything about the 2nd processor.
-	 * Instead we look for magic bits in magic registers,
-	 * in the hammerhead memory controller in the case of the
-	 * dual-cpu powersurge board.  -- paulus.
-	 */
-	if (find_devices("hammerhead") == NULL)
-		return 1;
-
-	hhead_base = ioremap(HAMMERHEAD_BASE, 0x800);
-	quad_base = ioremap(PSURGE_QUAD_REG_ADDR, 1024);
-	psurge_sec_intr = hhead_base + HHEAD_SEC_INTR;
-
-	psurge_type = psurge_quad_probe();
-	if (psurge_type != PSURGE_DUAL) {
-		psurge_quad_init();
-		/* All released cards using this HW design have 4 CPUs */
-		ncpus = 4;
-	} else {
-		iounmap(quad_base);
-		if ((in_8(hhead_base + HHEAD_CONFIG) & 0x02) == 0) {
-			/* not a dual-cpu card */
-			iounmap(hhead_base);
-			psurge_type = PSURGE_NONE;
-			return 1;
-		}
-		ncpus = 2;
-	}
-
-	psurge_start = ioremap(PSURGE_START, 4);
-	psurge_pri_intr = ioremap(PSURGE_PRI_INTR, 4);
-
-	/* this is not actually strictly necessary -- paulus. */
-	for (i = 1; i < ncpus; ++i)
-		smp_hw_index[i] = i;
-
-	if (ppc_md.progress) ppc_md.progress("smp_psurge_probe - done", 0x352);
-
-	return ncpus;
-}
-
-static void __init smp_psurge_kick_cpu(int nr)
-{
-	unsigned long start = __pa(__secondary_start_pmac_0) + nr * 8;
-	unsigned long a;
-
-	/* may need to flush here if secondary bats aren't setup */
-	for (a = KERNELBASE; a < KERNELBASE + 0x800000; a += 32)
-		asm volatile("dcbf 0,%0" : : "r" (a) : "memory");
-	asm volatile("sync");
-
-	if (ppc_md.progress) ppc_md.progress("smp_psurge_kick_cpu", 0x353);
-
-	out_be32(psurge_start, start);
-	mb();
-
-	psurge_set_ipi(nr);
-	udelay(10);
-	psurge_clr_ipi(nr);
-
-	if (ppc_md.progress) ppc_md.progress("smp_psurge_kick_cpu - done", 0x354);
-}
-
-/*
- * With the dual-cpu powersurge board, the decrementers and timebases
- * of both cpus are frozen after the secondary cpu is started up,
- * until we give the secondary cpu another interrupt.  This routine
- * uses this to get the timebases synchronized.
- *  -- paulus.
- */
-static void __init psurge_dual_sync_tb(int cpu_nr)
-{
-	int t;
-
-	set_dec(tb_ticks_per_jiffy);
-	set_tb(0, 0);
-	last_jiffy_stamp(cpu_nr) = 0;
-
-	if (cpu_nr > 0) {
-		mb();
-		sec_tb_reset = 1;
-		return;
-	}
-
-	/* wait for the secondary to have reset its TB before proceeding */
-	for (t = 10000000; t > 0 && !sec_tb_reset; --t)
-		;
-
-	/* now interrupt the secondary, starting both TBs */
-	psurge_set_ipi(1);
-
-	smp_tb_synchronized = 1;
-}
-
-static struct irqaction psurge_irqaction = {
-	.handler = psurge_primary_intr,
-	.flags = SA_INTERRUPT,
-	.mask = CPU_MASK_NONE,
-	.name = "primary IPI",
-};
-
-static void __init smp_psurge_setup_cpu(int cpu_nr)
-{
-
-	if (cpu_nr == 0) {
-		/* If we failed to start the second CPU, we should still
-		 * send it an IPI to start the timebase & DEC or we might
-		 * have them stuck.
-		 */
-		if (num_online_cpus() < 2) {
-			if (psurge_type == PSURGE_DUAL)
-				psurge_set_ipi(1);
-			return;
-		}
-		/* reset the entry point so if we get another intr we won't
-		 * try to startup again */
-		out_be32(psurge_start, 0x100);
-		if (setup_irq(30, &psurge_irqaction))
-			printk(KERN_ERR "Couldn't get primary IPI interrupt");
-	}
-
-	if (psurge_type == PSURGE_DUAL)
-		psurge_dual_sync_tb(cpu_nr);
-}
-
-void __init smp_psurge_take_timebase(void)
-{
-	/* Dummy implementation */
-}
-
-void __init smp_psurge_give_timebase(void)
-{
-	/* Dummy implementation */
-}
-
-static int __init smp_core99_probe(void)
-{
-#ifdef CONFIG_6xx
-	extern int powersave_nap;
-#endif
-	struct device_node *cpus, *firstcpu;
-	int i, ncpus = 0, boot_cpu = -1;
-	u32 *tbprop = NULL;
-
-	if (ppc_md.progress) ppc_md.progress("smp_core99_probe", 0x345);
-	cpus = firstcpu = find_type_devices("cpu");
-	while(cpus != NULL) {
-		u32 *regprop = (u32 *)get_property(cpus, "reg", NULL);
-		char *stateprop = (char *)get_property(cpus, "state", NULL);
-		if (regprop != NULL && stateprop != NULL &&
-		    !strncmp(stateprop, "running", 7))
-			boot_cpu = *regprop;
-		++ncpus;
-		cpus = cpus->next;
-	}
-	if (boot_cpu == -1)
-		printk(KERN_WARNING "Couldn't detect boot CPU !\n");
-	if (boot_cpu != 0)
-		printk(KERN_WARNING "Boot CPU is %d, unsupported setup !\n", boot_cpu);
-
-	if (machine_is_compatible("MacRISC4")) {
-		extern struct smp_ops_t core99_smp_ops;
-
-		core99_smp_ops.take_timebase = smp_generic_take_timebase;
-		core99_smp_ops.give_timebase = smp_generic_give_timebase;
-	} else {
-		if (firstcpu != NULL)
-			tbprop = (u32 *)get_property(firstcpu, "timebase-enable", NULL);
-		if (tbprop)
-			core99_tb_gpio = *tbprop;
-		else
-			core99_tb_gpio = KL_GPIO_TB_ENABLE;
-	}
-
-	if (ncpus > 1) {
-		openpic_request_IPIs();
-		for (i = 1; i < ncpus; ++i)
-			smp_hw_index[i] = i;
-#ifdef CONFIG_6xx
-		powersave_nap = 0;
-#endif
-		core99_init_caches(0);
-	}
-
-	return ncpus;
-}
-
-static void __devinit smp_core99_kick_cpu(int nr)
-{
-	unsigned long save_vector, new_vector;
-	unsigned long flags;
-
-	volatile unsigned long *vector
-		 = ((volatile unsigned long *)(KERNELBASE+0x100));
-	if (nr < 0 || nr > 3)
-		return;
-	if (ppc_md.progress) ppc_md.progress("smp_core99_kick_cpu", 0x346);
-
-	local_irq_save(flags);
-	local_irq_disable();
-
-	/* Save reset vector */
-	save_vector = *vector;
-
-	/* Setup fake reset vector that does	
-	 *   b __secondary_start_pmac_0 + nr*8 - KERNELBASE
-	 */
-	new_vector = (unsigned long) __secondary_start_pmac_0 + nr * 8;
-	*vector = 0x48000002 + new_vector - KERNELBASE;
-
-	/* flush data cache and inval instruction cache */
-	flush_icache_range((unsigned long) vector, (unsigned long) vector + 4);
-
-	/* Put some life in our friend */
-	pmac_call_feature(PMAC_FTR_RESET_CPU, NULL, nr, 0);
-
-	/* FIXME: We wait a bit for the CPU to take the exception, I should
-	 * instead wait for the entry code to set something for me. Well,
-	 * ideally, all that crap will be done in prom.c and the CPU left
-	 * in a RAM-based wait loop like CHRP.
-	 */
-	mdelay(1);
-
-	/* Restore our exception vector */
-	*vector = save_vector;
-	flush_icache_range((unsigned long) vector, (unsigned long) vector + 4);
-
-	local_irq_restore(flags);
-	if (ppc_md.progress) ppc_md.progress("smp_core99_kick_cpu done", 0x347);
-}
-
-static void __devinit smp_core99_setup_cpu(int cpu_nr)
-{
-	/* Setup L2/L3 */
-	if (cpu_nr != 0)
-		core99_init_caches(cpu_nr);
-
-	/* Setup openpic */
-	do_openpic_setup_cpu();
-
-	if (cpu_nr == 0) {
-#ifdef CONFIG_POWER4
-		extern void g5_phy_disable_cpu1(void);
-
-		/* If we didn't start the second CPU, we must take
-		 * it off the bus
-		 */
-		if (machine_is_compatible("MacRISC4") &&
-		    num_online_cpus() < 2)		
-			g5_phy_disable_cpu1();
-#endif /* CONFIG_POWER4 */
-		if (ppc_md.progress) ppc_md.progress("core99_setup_cpu 0 done", 0x349);
-	}
-}
-
-/* not __init, called in sleep/wakeup code */
-void smp_core99_take_timebase(void)
-{
-	unsigned long flags;
-
-	/* tell the primary we're here */
-	sec_tb_reset = 1;
-	mb();
-
-	/* wait for the primary to set pri_tb_hi/lo */
-	while (sec_tb_reset < 2)
-		mb();
-
-	/* set our stuff the same as the primary */
-	local_irq_save(flags);
-	set_dec(1);
-	set_tb(pri_tb_hi, pri_tb_lo);
-	last_jiffy_stamp(smp_processor_id()) = pri_tb_stamp;
-	mb();
-
-	/* tell the primary we're done */
-       	sec_tb_reset = 0;
-	mb();
-	local_irq_restore(flags);
-}
-
-/* not __init, called in sleep/wakeup code */
-void smp_core99_give_timebase(void)
-{
-	unsigned long flags;
-	unsigned int t;
-
-	/* wait for the secondary to be in take_timebase */
-	for (t = 100000; t > 0 && !sec_tb_reset; --t)
-		udelay(10);
-	if (!sec_tb_reset) {
-		printk(KERN_WARNING "Timeout waiting sync on second CPU\n");
-		return;
-	}
-
-	/* freeze the timebase and read it */
-	/* disable interrupts so the timebase is disabled for the
-	   shortest possible time */
-	local_irq_save(flags);
-	pmac_call_feature(PMAC_FTR_WRITE_GPIO, NULL, core99_tb_gpio, 4);
-	pmac_call_feature(PMAC_FTR_READ_GPIO, NULL, core99_tb_gpio, 0);
-	mb();
-	pri_tb_hi = get_tbu();
-	pri_tb_lo = get_tbl();
-	pri_tb_stamp = last_jiffy_stamp(smp_processor_id());
-	mb();
-
-	/* tell the secondary we're ready */
-	sec_tb_reset = 2;
-	mb();
-
-	/* wait for the secondary to have taken it */
-	for (t = 100000; t > 0 && sec_tb_reset; --t)
-		udelay(10);
-	if (sec_tb_reset)
-		printk(KERN_WARNING "Timeout waiting sync(2) on second CPU\n");
-	else
-		smp_tb_synchronized = 1;
-
-	/* Now, restart the timebase by leaving the GPIO to an open collector */
-       	pmac_call_feature(PMAC_FTR_WRITE_GPIO, NULL, core99_tb_gpio, 0);
-        pmac_call_feature(PMAC_FTR_READ_GPIO, NULL, core99_tb_gpio, 0);
-	local_irq_restore(flags);
-}
-
-
-/* PowerSurge-style Macs */
-struct smp_ops_t psurge_smp_ops = {
-	.message_pass	= smp_psurge_message_pass,
-	.probe		= smp_psurge_probe,
-	.kick_cpu	= smp_psurge_kick_cpu,
-	.setup_cpu	= smp_psurge_setup_cpu,
-	.give_timebase	= smp_psurge_give_timebase,
-	.take_timebase	= smp_psurge_take_timebase,
-};
-
-/* Core99 Macs (dual G4s) */
-struct smp_ops_t core99_smp_ops = {
-	.message_pass	= smp_openpic_message_pass,
-	.probe		= smp_core99_probe,
-	.kick_cpu	= smp_core99_kick_cpu,
-	.setup_cpu	= smp_core99_setup_cpu,
-	.give_timebase	= smp_core99_give_timebase,
-	.take_timebase	= smp_core99_take_timebase,
-};
-
-#ifdef CONFIG_HOTPLUG_CPU
-
-int __cpu_disable(void)
-{
-	cpu_clear(smp_processor_id(), cpu_online_map);
-
-	/* XXX reset cpu affinity here */
-	openpic_set_priority(0xf);
-	asm volatile("mtdec %0" : : "r" (0x7fffffff));
-	mb();
-	udelay(20);
-	asm volatile("mtdec %0" : : "r" (0x7fffffff));
-	return 0;
-}
-
-extern void low_cpu_die(void) __attribute__((noreturn)); /* in pmac_sleep.S */
-static int cpu_dead[NR_CPUS];
-
-void cpu_die(void)
-{
-	local_irq_disable();
-	cpu_dead[smp_processor_id()] = 1;
-	mb();
-	low_cpu_die();
-}
-
-void __cpu_die(unsigned int cpu)
-{
-	int timeout;
-
-	timeout = 1000;
-	while (!cpu_dead[cpu]) {
-		if (--timeout == 0) {
-			printk("CPU %u refused to die!\n", cpu);
-			break;
-		}
-		msleep(1);
-	}
-	cpu_callin_map[cpu] = 0;
-	cpu_dead[cpu] = 0;
-}
-
-#endif
diff --git a/arch/ppc/platforms/pmac_time.c b/arch/ppc/platforms/pmac_time.c
deleted file mode 100644
index edb9fcc6479..00000000000
--- a/arch/ppc/platforms/pmac_time.c
+++ /dev/null
@@ -1,291 +0,0 @@
-/*
- * Support for periodic interrupts (100 per second) and for getting
- * the current time from the RTC on Power Macintoshes.
- *
- * We use the decrementer register for our periodic interrupts.
- *
- * Paul Mackerras	August 1996.
- * Copyright (C) 1996 Paul Mackerras.
- */
-#include <linux/config.h>
-#include <linux/errno.h>
-#include <linux/sched.h>
-#include <linux/kernel.h>
-#include <linux/param.h>
-#include <linux/string.h>
-#include <linux/mm.h>
-#include <linux/init.h>
-#include <linux/time.h>
-#include <linux/adb.h>
-#include <linux/cuda.h>
-#include <linux/pmu.h>
-#include <linux/hardirq.h>
-
-#include <asm/sections.h>
-#include <asm/prom.h>
-#include <asm/system.h>
-#include <asm/io.h>
-#include <asm/pgtable.h>
-#include <asm/machdep.h>
-#include <asm/time.h>
-#include <asm/nvram.h>
-
-/* Apparently the RTC stores seconds since 1 Jan 1904 */
-#define RTC_OFFSET	2082844800
-
-/*
- * Calibrate the decrementer frequency with the VIA timer 1.
- */
-#define VIA_TIMER_FREQ_6	4700000	/* time 1 frequency * 6 */
-
-/* VIA registers */
-#define RS		0x200		/* skip between registers */
-#define T1CL		(4*RS)		/* Timer 1 ctr/latch (low 8 bits) */
-#define T1CH		(5*RS)		/* Timer 1 counter (high 8 bits) */
-#define T1LL		(6*RS)		/* Timer 1 latch (low 8 bits) */
-#define T1LH		(7*RS)		/* Timer 1 latch (high 8 bits) */
-#define ACR		(11*RS)		/* Auxiliary control register */
-#define IFR		(13*RS)		/* Interrupt flag register */
-
-/* Bits in ACR */
-#define T1MODE		0xc0		/* Timer 1 mode */
-#define T1MODE_CONT	0x40		/*  continuous interrupts */
-
-/* Bits in IFR and IER */
-#define T1_INT		0x40		/* Timer 1 interrupt */
-
-extern struct timezone sys_tz;
-
-long __init
-pmac_time_init(void)
-{
-#ifdef CONFIG_NVRAM
-	s32 delta = 0;
-	int dst;
-	
-	delta = ((s32)pmac_xpram_read(PMAC_XPRAM_MACHINE_LOC + 0x9)) << 16;
-	delta |= ((s32)pmac_xpram_read(PMAC_XPRAM_MACHINE_LOC + 0xa)) << 8;
-	delta |= pmac_xpram_read(PMAC_XPRAM_MACHINE_LOC + 0xb);
-	if (delta & 0x00800000UL)
-		delta |= 0xFF000000UL;
-	dst = ((pmac_xpram_read(PMAC_XPRAM_MACHINE_LOC + 0x8) & 0x80) != 0);
-	printk("GMT Delta read from XPRAM: %d minutes, DST: %s\n", delta/60,
-		dst ? "on" : "off");
-	return delta;
-#else
-	return 0;
-#endif
-}
-
-unsigned long
-pmac_get_rtc_time(void)
-{
-#if defined(CONFIG_ADB_CUDA) || defined(CONFIG_ADB_PMU)
-	struct adb_request req;
-	unsigned long now;
-#endif
-
-	/* Get the time from the RTC */
-	switch (sys_ctrler) {
-#ifdef CONFIG_ADB_CUDA
-	case SYS_CTRLER_CUDA:
-		if (cuda_request(&req, NULL, 2, CUDA_PACKET, CUDA_GET_TIME) < 0)
-			return 0;
-		while (!req.complete)
-			cuda_poll();
-		if (req.reply_len != 7)
-			printk(KERN_ERR "pmac_get_rtc_time: got %d byte reply\n",
-			       req.reply_len);
-		now = (req.reply[3] << 24) + (req.reply[4] << 16)
-			+ (req.reply[5] << 8) + req.reply[6];
-		return now - RTC_OFFSET;
-#endif /* CONFIG_ADB_CUDA */
-#ifdef CONFIG_ADB_PMU
-	case SYS_CTRLER_PMU:
-		if (pmu_request(&req, NULL, 1, PMU_READ_RTC) < 0)
-			return 0;
-		while (!req.complete)
-			pmu_poll();
-		if (req.reply_len != 4)
-			printk(KERN_ERR "pmac_get_rtc_time: got %d byte reply\n",
-			       req.reply_len);
-		now = (req.reply[0] << 24) + (req.reply[1] << 16)
-			+ (req.reply[2] << 8) + req.reply[3];
-		return now - RTC_OFFSET;
-#endif /* CONFIG_ADB_PMU */
-	default: ;
-	}
-	return 0;
-}
-
-int
-pmac_set_rtc_time(unsigned long nowtime)
-{
-#if defined(CONFIG_ADB_CUDA) || defined(CONFIG_ADB_PMU)
-	struct adb_request req;
-#endif
-
-	nowtime += RTC_OFFSET;
-
-	switch (sys_ctrler) {
-#ifdef CONFIG_ADB_CUDA
-	case SYS_CTRLER_CUDA:
-		if (cuda_request(&req, NULL, 6, CUDA_PACKET, CUDA_SET_TIME,
-				 nowtime >> 24, nowtime >> 16, nowtime >> 8, nowtime) < 0)
-			return 0;
-		while (!req.complete)
-			cuda_poll();
-		if ((req.reply_len != 3) && (req.reply_len != 7))
-			printk(KERN_ERR "pmac_set_rtc_time: got %d byte reply\n",
-			       req.reply_len);
-		return 1;
-#endif /* CONFIG_ADB_CUDA */
-#ifdef CONFIG_ADB_PMU
-	case SYS_CTRLER_PMU:
-		if (pmu_request(&req, NULL, 5, PMU_SET_RTC,
-				nowtime >> 24, nowtime >> 16, nowtime >> 8, nowtime) < 0)
-			return 0;
-		while (!req.complete)
-			pmu_poll();
-		if (req.reply_len != 0)
-			printk(KERN_ERR "pmac_set_rtc_time: got %d byte reply\n",
-			       req.reply_len);
-		return 1;
-#endif /* CONFIG_ADB_PMU */
-	default:
-		return 0;
-	}
-}
-
-/*
- * Calibrate the decrementer register using VIA timer 1.
- * This is used both on powermacs and CHRP machines.
- */
-int __init
-via_calibrate_decr(void)
-{
-	struct device_node *vias;
-	volatile unsigned char __iomem *via;
-	int count = VIA_TIMER_FREQ_6 / 100;
-	unsigned int dstart, dend;
-
-	vias = find_devices("via-cuda");
-	if (vias == 0)
-		vias = find_devices("via-pmu");
-	if (vias == 0)
-		vias = find_devices("via");
-	if (vias == 0 || vias->n_addrs == 0)
-		return 0;
-	via = ioremap(vias->addrs[0].address, vias->addrs[0].size);
-
-	/* set timer 1 for continuous interrupts */
-	out_8(&via[ACR], (via[ACR] & ~T1MODE) | T1MODE_CONT);
-	/* set the counter to a small value */
-	out_8(&via[T1CH], 2);
-	/* set the latch to `count' */
-	out_8(&via[T1LL], count);
-	out_8(&via[T1LH], count >> 8);
-	/* wait until it hits 0 */
-	while ((in_8(&via[IFR]) & T1_INT) == 0)
-		;
-	dstart = get_dec();
-	/* clear the interrupt & wait until it hits 0 again */
-	in_8(&via[T1CL]);
-	while ((in_8(&via[IFR]) & T1_INT) == 0)
-		;
-	dend = get_dec();
-
-	tb_ticks_per_jiffy = (dstart - dend) / ((6 * HZ)/100);
-	tb_to_us = mulhwu_scale_factor(dstart - dend, 60000);
-
-	printk(KERN_INFO "via_calibrate_decr: ticks per jiffy = %u (%u ticks)\n",
-	       tb_ticks_per_jiffy, dstart - dend);
-
-	iounmap(via);
-	
-	return 1;
-}
-
-#ifdef CONFIG_PM
-/*
- * Reset the time after a sleep.
- */
-static int
-time_sleep_notify(struct pmu_sleep_notifier *self, int when)
-{
-	static unsigned long time_diff;
-	unsigned long flags;
-	unsigned long seq;
-
-	switch (when) {
-	case PBOOK_SLEEP_NOW:
-		do {
-			seq = read_seqbegin_irqsave(&xtime_lock, flags);
-			time_diff = xtime.tv_sec - pmac_get_rtc_time();
-		} while (read_seqretry_irqrestore(&xtime_lock, seq, flags));
-		break;
-	case PBOOK_WAKE:
-		write_seqlock_irqsave(&xtime_lock, flags);
-		xtime.tv_sec = pmac_get_rtc_time() + time_diff;
-		xtime.tv_nsec = 0;
-		last_rtc_update = xtime.tv_sec;
-		write_sequnlock_irqrestore(&xtime_lock, flags);
-		break;
-	}
-	return PBOOK_SLEEP_OK;
-}
-
-static struct pmu_sleep_notifier time_sleep_notifier = {
-	time_sleep_notify, SLEEP_LEVEL_MISC,
-};
-#endif /* CONFIG_PM */
-
-/*
- * Query the OF and get the decr frequency.
- * This was taken from the pmac time_init() when merging the prep/pmac
- * time functions.
- */
-void __init
-pmac_calibrate_decr(void)
-{
-	struct device_node *cpu;
-	unsigned int freq, *fp;
-
-#ifdef CONFIG_PM
-	pmu_register_sleep_notifier(&time_sleep_notifier);
-#endif /* CONFIG_PM */
-
-	/* We assume MacRISC2 machines have correct device-tree
-	 * calibration. That's better since the VIA itself seems
-	 * to be slightly off. --BenH
-	 */
-	if (!machine_is_compatible("MacRISC2") &&
-	    !machine_is_compatible("MacRISC3") &&
-	    !machine_is_compatible("MacRISC4"))
-		if (via_calibrate_decr())
-			return;
-
-	/* Special case: QuickSilver G4s seem to have a badly calibrated
-	 * timebase-frequency in OF, VIA is much better on these. We should
-	 * probably implement calibration based on the KL timer on these
-	 * machines anyway... -BenH
-	 */
-	if (machine_is_compatible("PowerMac3,5"))
-		if (via_calibrate_decr())
-			return;
-	/*
-	 * The cpu node should have a timebase-frequency property
-	 * to tell us the rate at which the decrementer counts.
-	 */
-	cpu = find_type_devices("cpu");
-	if (cpu == 0)
-		panic("can't find cpu node in time_init");
-	fp = (unsigned int *) get_property(cpu, "timebase-frequency", NULL);
-	if (fp == 0)
-		panic("can't get cpu timebase frequency");
-	freq = *fp;
-	printk("time_init: decrementer frequency = %u.%.6u MHz\n",
-	       freq/1000000, freq%1000000);
-	tb_ticks_per_jiffy = freq / HZ;
-	tb_to_us = mulhwu_scale_factor(freq, 1000000);
-}
diff --git a/arch/ppc/syslib/Makefile b/arch/ppc/syslib/Makefile
index 84ef03018d0..159dcd92a6d 100644
--- a/arch/ppc/syslib/Makefile
+++ b/arch/ppc/syslib/Makefile
@@ -39,8 +39,6 @@ obj-$(CONFIG_8xx)		+= m8xx_setup.o ppc8xx_pic.o $(wdt-mpc8xx-y) \
 				   ppc_sys.o mpc8xx_devices.o mpc8xx_sys.o
 obj-$(CONFIG_PCI_QSPAN)		+= qspan_pci.o
 obj-$(CONFIG_PPC_OF)		+= prom_init.o prom.o
-obj-$(CONFIG_PPC_PMAC)		+= open_pic.o
-obj-$(CONFIG_POWER4)		+= open_pic2.o
 obj-$(CONFIG_PPC_CHRP)		+= open_pic.o
 obj-$(CONFIG_PPC_PREP)		+= open_pic.o todc_time.o
 obj-$(CONFIG_BAMBOO)		+= pci_auto.o todc_time.o
diff --git a/arch/ppc/syslib/prom.c b/arch/ppc/syslib/prom.c
index af4deace49e..482f837fd37 100644
--- a/arch/ppc/syslib/prom.c
+++ b/arch/ppc/syslib/prom.c
@@ -70,8 +70,6 @@ int use_of_interrupt_tree;
 struct device_node *dflt_interrupt_controller;
 int num_interrupt_controllers;
 
-int pmac_newworld;
-
 extern unsigned int rtas_entry;  /* physical pointer */
 
 extern struct device_node *allnodes;
@@ -123,22 +121,13 @@ finish_device_tree(void)
 	unsigned long mem = (unsigned long) klimit;
 	struct device_node *np;
 
-	/* All newworld pmac machines and CHRPs now use the interrupt tree */
+	/* All CHRPs now use the interrupt tree */
 	for (np = allnodes; np != NULL; np = np->allnext) {
 		if (get_property(np, "interrupt-parent", NULL)) {
 			use_of_interrupt_tree = 1;
 			break;
 		}
 	}
-	if (_machine == _MACH_Pmac && use_of_interrupt_tree)
-		pmac_newworld = 1;
-
-#ifdef CONFIG_BOOTX_TEXT
-	if (boot_infos && pmac_newworld) {
-		prom_print("WARNING ! BootX/miBoot booting is not supported on this machine\n");
-		prom_print("          You should use an Open Firmware bootloader\n");
-	}
-#endif /* CONFIG_BOOTX_TEXT */
 
 	if (use_of_interrupt_tree) {
 		/*
@@ -434,16 +423,10 @@ finish_node_interrupts(struct device_node *np, unsigned long mem_start)
 		 * those machines, we want to offset interrupts from the
 		 * second openpic by 128 -- BenH
 		 */
-		if (_machine != _MACH_Pmac && num_interrupt_controllers > 1
+		if (num_interrupt_controllers > 1
 		    && ic != NULL
 		    && get_property(ic, "interrupt-parent", NULL) == NULL)
 			offset = 16;
-		else if (_machine == _MACH_Pmac && num_interrupt_controllers > 1
-			 && ic != NULL && ic->parent != NULL) {
-			char *name = get_property(ic->parent, "name", NULL);
-			if (name && !strcmp(name, "u3"))
-				offset = 128;
-		}
 
 		np->intrs[i].line = irq[0] + offset;
 		if (n > 1)
diff --git a/arch/ppc/xmon/start.c b/arch/ppc/xmon/start.c
index c80177f8ec0..4344cbe9b5c 100644
--- a/arch/ppc/xmon/start.c
+++ b/arch/ppc/xmon/start.c
@@ -18,7 +18,6 @@
 #include <asm/bootx.h>
 #include <asm/machdep.h>
 #include <asm/errno.h>
-#include <asm/pmac_feature.h>
 #include <asm/processor.h>
 #include <asm/delay.h>
 #include <asm/btext.h>
@@ -27,11 +26,9 @@ static volatile unsigned char *sccc, *sccd;
 unsigned int TXRDY, RXRDY, DLAB;
 static int xmon_expect(const char *str, unsigned int timeout);
 
-static int use_serial;
 static int use_screen;
 static int via_modem;
 static int xmon_use_sccb;
-static struct device_node *channel_node;
 
 #define TB_SPEED	25000000
 
@@ -112,96 +109,21 @@ xmon_map_scc(void)
 #ifdef CONFIG_PPC_MULTIPLATFORM
 	volatile unsigned char *base;
 
-	if (_machine == _MACH_Pmac) {
-		struct device_node *np;
-		unsigned long addr;
-#ifdef CONFIG_BOOTX_TEXT
-		if (!use_screen && !use_serial
-		    && !machine_is_compatible("iMac")) {
-			/* see if there is a keyboard in the device tree
-			   with a parent of type "adb" */
-			for (np = find_devices("keyboard"); np; np = np->next)
-				if (np->parent && np->parent->type
-				    && strcmp(np->parent->type, "adb") == 0)
-					break;
-
-			/* needs to be hacked if xmon_printk is to be used
-			   from within find_via_pmu() */
-#ifdef CONFIG_ADB_PMU
-			if (np != NULL && boot_text_mapped && find_via_pmu())
-				use_screen = 1;
-#endif
-#ifdef CONFIG_ADB_CUDA
-			if (np != NULL && boot_text_mapped && find_via_cuda())
-				use_screen = 1;
-#endif
-		}
-		if (!use_screen && (np = find_devices("escc")) != NULL) {
-			/*
-			 * look for the device node for the serial port
-			 * we're using and see if it says it has a modem
-			 */
-			char *name = xmon_use_sccb? "ch-b": "ch-a";
-			char *slots;
-			int l;
-
-			np = np->child;
-			while (np != NULL && strcmp(np->name, name) != 0)
-				np = np->sibling;
-			if (np != NULL) {
-				/* XXX should parse this properly */
-				channel_node = np;
-				slots = get_property(np, "slot-names", &l);
-				if (slots != NULL && l >= 10
-				    && strcmp(slots+4, "Modem") == 0)
-					via_modem = 1;
-			}
-		}
-		btext_drawstring("xmon uses ");
-		if (use_screen)
-			btext_drawstring("screen and keyboard\n");
-		else {
-			if (via_modem)
-				btext_drawstring("modem on ");
-			btext_drawstring(xmon_use_sccb? "printer": "modem");
-			btext_drawstring(" port\n");
-		}
-
-#endif /* CONFIG_BOOTX_TEXT */
-
-#ifdef CHRP_ESCC
-		addr = 0xc1013020;
-#else
-		addr = 0xf3013020;
-#endif
-		TXRDY = 4;
-		RXRDY = 1;
-	
-		np = find_devices("mac-io");
-		if (np && np->n_addrs)
-			addr = np->addrs[0].address + 0x13020;
-		base = (volatile unsigned char *) ioremap(addr & PAGE_MASK, PAGE_SIZE);
-		sccc = base + (addr & ~PAGE_MASK);
-		sccd = sccc + 0x10;
-
-	}
 #ifdef CONFIG_PPC_CHRP
-	else {
-		base = (volatile unsigned char *) isa_io_base;
-		if (_machine == _MACH_chrp)
-			base = (volatile unsigned char *)
-				ioremap(chrp_find_phys_io_base(), 0x1000);
-
-		sccc = base + 0x3fd;
-		sccd = base + 0x3f8;
-		if (xmon_use_sccb) {
-			sccc -= 0x100;
-			sccd -= 0x100;
-		}
-		TXRDY = 0x20;
-		RXRDY = 1;
-		DLAB = 0x80;
+	base = (volatile unsigned char *) isa_io_base;
+	if (_machine == _MACH_chrp)
+		base = (volatile unsigned char *)
+			ioremap(chrp_find_phys_io_base(), 0x1000);
+
+	sccc = base + 0x3fd;
+	sccd = base + 0x3f8;
+	if (xmon_use_sccb) {
+		sccc -= 0x100;
+		sccd -= 0x100;
 	}
+	TXRDY = 0x20;
+	RXRDY = 1;
+	DLAB = 0x80;
 #endif /* CONFIG_PPC_CHRP */
 #elif defined(CONFIG_GEMINI)
 	/* should already be mapped by the kernel boot */
@@ -385,16 +307,6 @@ xmon_read_poll(void)
 	return *sccd;
 }
 
-static unsigned char scc_inittab[] = {
-    13, 0,		/* set baud rate divisor */
-    12, 1,
-    14, 1,		/* baud rate gen enable, src=rtxc */
-    11, 0x50,		/* clocks = br gen */
-    5,  0xea,		/* tx 8 bits, assert DTR & RTS */
-    4,  0x46,		/* x16 clock, 1 stop */
-    3,  0xc1,		/* rx enable, 8 bits */
-};
-
 void
 xmon_init_scc(void)
 {
@@ -407,43 +319,6 @@ xmon_init_scc(void)
 		sccd[3] = 3; eieio();		/* LCR = 8N1 */
 		sccd[1] = 0; eieio();		/* IER = 0 */
 	}
-	else if ( _machine == _MACH_Pmac )
-	{
-		int i, x;
-
-		if (channel_node != 0)
-			pmac_call_feature(
-				PMAC_FTR_SCC_ENABLE,
-				channel_node,
-				PMAC_SCC_ASYNC | PMAC_SCC_FLAG_XMON, 1);
-			printk(KERN_INFO "Serial port locked ON by debugger !\n");
-		if (via_modem && channel_node != 0) {
-			unsigned int t0;
-
-			pmac_call_feature(
-				PMAC_FTR_MODEM_ENABLE,
-				channel_node, 0, 1);
-			printk(KERN_INFO "Modem powered up by debugger !\n");
-			t0 = readtb();
-			while (readtb() - t0 < 3*TB_SPEED)
-				eieio();
-		}
-		/* use the B channel if requested */
-		if (xmon_use_sccb) {
-			sccc = (volatile unsigned char *)
-				((unsigned long)sccc & ~0x20);
-			sccd = sccc + 0x10;
-		}
-		for (i = 20000; i != 0; --i) {
-			x = *sccc; eieio();
-		}
-		*sccc = 9; eieio();		/* reset A or B side */
-		*sccc = ((unsigned long)sccc & 0x20)? 0x80: 0x40; eieio();
-		for (i = 0; i < sizeof(scc_inittab); ++i) {
-			*sccc = scc_inittab[i];
-			eieio();
-		}
-	}
 	scc_initialized = 1;
 	if (via_modem) {
 		for (;;) {
@@ -632,19 +507,9 @@ xmon_fgets(char *str, int nb, void *f)
 void
 xmon_enter(void)
 {
-#ifdef CONFIG_ADB_PMU
-	if (_machine == _MACH_Pmac) {
-		pmu_suspend();
-	}
-#endif
 }
 
 void
 xmon_leave(void)
 {
-#ifdef CONFIG_ADB_PMU
-	if (_machine == _MACH_Pmac) {
-		pmu_resume();
-	}
-#endif
 }
diff --git a/arch/ppc/xmon/xmon.c b/arch/ppc/xmon/xmon.c
index 9075a7538e2..bdaf6597b4c 100644
--- a/arch/ppc/xmon/xmon.c
+++ b/arch/ppc/xmon/xmon.c
@@ -16,9 +16,6 @@
 #include <asm/bootx.h>
 #include <asm/machdep.h>
 #include <asm/xmon.h>
-#ifdef CONFIG_PMAC_BACKLIGHT
-#include <asm/backlight.h>
-#endif
 #include "nonstdio.h"
 #include "privinst.h"
 
@@ -260,16 +257,6 @@ int xmon(struct pt_regs *excp)
 	 */
 #endif /* CONFIG_SMP */
 	remove_bpts();
-#ifdef CONFIG_PMAC_BACKLIGHT
-	if( setjmp(bus_error_jmp) == 0 ) {
-		debugger_fault_handler = handle_fault;
-		sync();
-		set_backlight_enable(1);
-		set_backlight_level(BACKLIGHT_MAX);
-		sync();
-	}
-	debugger_fault_handler = NULL;
-#endif	/* CONFIG_PMAC_BACKLIGHT */
 	cmd = cmds(excp);
 	if (cmd == 's') {
 		xmon_trace[smp_processor_id()] = SSTEP;
author	Linus Torvalds <torvalds@g5.osdl.org>	2006-01-15 10:05:10 -0800
committer	Linus Torvalds <torvalds@g5.osdl.org>	2006-01-15 10:05:10 -0800
commit	fc03da1ca1954f103ed57daf90611cefa57b07e0 (patch)
tree	2b9b44b1a39f7743c1c3d7bc89654792686d7dbc /arch
parent	caf5b04c82f05c65843b2d7189845d6c3df5a41e (diff)
parent	e05b3b4adbaeea508bd1c195f1f2e22c8251176b (diff)