diff options
author | Mikael Starvik <mikael.starvik@axis.com> | 2005-07-27 11:44:51 -0700 |
---|---|---|
committer | Linus Torvalds <torvalds@g5.osdl.org> | 2005-07-27 16:26:02 -0700 |
commit | e63b68de5c9bf68cfb4a272469147b19176d76d6 (patch) | |
tree | b7360d771a16fee23a2309c2b66726d1880e24f5 /drivers/ide/cris/ide-v10.c | |
parent | 51533b615e605d86154ec1b4e585c8ca1b0b15b7 (diff) |
[PATCH] CRIS IDE driver
* Added abstraction layer for subarchs.
* Added v32 support.
* Renamed driver.
Signed-off-by: Mikael Starvik <starvik@axis.com>
Acked-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Diffstat (limited to 'drivers/ide/cris/ide-v10.c')
-rw-r--r-- | drivers/ide/cris/ide-v10.c | 842 |
1 files changed, 0 insertions, 842 deletions
diff --git a/drivers/ide/cris/ide-v10.c b/drivers/ide/cris/ide-v10.c deleted file mode 100644 index 5b40220d3dd..00000000000 --- a/drivers/ide/cris/ide-v10.c +++ /dev/null @@ -1,842 +0,0 @@ -/* $Id: ide.c,v 1.4 2004/10/12 07:55:48 starvik Exp $ - * - * Etrax specific IDE functions, like init and PIO-mode setting etc. - * Almost the entire ide.c is used for the rest of the Etrax ATA driver. - * Copyright (c) 2000-2004 Axis Communications AB - * - * Authors: Bjorn Wesen (initial version) - * Mikael Starvik (pio setup stuff, Linux 2.6 port) - */ - -/* Regarding DMA: - * - * There are two forms of DMA - "DMA handshaking" between the interface and the drive, - * and DMA between the memory and the interface. We can ALWAYS use the latter, since it's - * something built-in in the Etrax. However only some drives support the DMA-mode handshaking - * on the ATA-bus. The normal PC driver and Triton interface disables memory-if DMA when the - * device can't do DMA handshaking for some stupid reason. We don't need to do that. - */ - -#undef REALLY_SLOW_IO /* most systems can safely undef this */ - -#include <linux/config.h> -#include <linux/types.h> -#include <linux/kernel.h> -#include <linux/timer.h> -#include <linux/mm.h> -#include <linux/interrupt.h> -#include <linux/delay.h> -#include <linux/blkdev.h> -#include <linux/hdreg.h> -#include <linux/ide.h> -#include <linux/init.h> -#include <linux/scatterlist.h> - -#include <asm/io.h> -#include <asm/arch/svinto.h> -#include <asm/dma.h> - -/* number of Etrax DMA descriptors */ -#define MAX_DMA_DESCRS 64 - -/* number of times to retry busy-flags when reading/writing IDE-registers - * this can't be too high because a hung harddisk might cause the watchdog - * to trigger (sometimes INB and OUTB are called with irq's disabled) - */ - -#define IDE_REGISTER_TIMEOUT 300 - -static int e100_read_command = 0; - -#define LOWDB(x) -#define D(x) - -static int e100_ide_build_dmatable (ide_drive_t *drive); -static ide_startstop_t etrax_dma_intr (ide_drive_t *drive); - -void -etrax100_ide_outw(unsigned short data, unsigned long reg) { - int timeleft; - LOWDB(printk("ow: data 0x%x, reg 0x%x\n", data, reg)); - - /* note the lack of handling any timeouts. we stop waiting, but we don't - * really notify anybody. - */ - - timeleft = IDE_REGISTER_TIMEOUT; - /* wait for busy flag */ - while(timeleft && (*R_ATA_STATUS_DATA & IO_MASK(R_ATA_STATUS_DATA, busy))) - timeleft--; - - /* - * Fall through at a timeout, so the ongoing command will be - * aborted by the write below, which is expected to be a dummy - * command to the command register. This happens when a faulty - * drive times out on a command. See comment on timeout in - * INB. - */ - if(!timeleft) - printk("ATA timeout reg 0x%lx := 0x%x\n", reg, data); - - *R_ATA_CTRL_DATA = reg | data; /* write data to the drive's register */ - - timeleft = IDE_REGISTER_TIMEOUT; - /* wait for transmitter ready */ - while(timeleft && !(*R_ATA_STATUS_DATA & - IO_MASK(R_ATA_STATUS_DATA, tr_rdy))) - timeleft--; -} - -void -etrax100_ide_outb(unsigned char data, unsigned long reg) -{ - etrax100_ide_outw(data, reg); -} - -void -etrax100_ide_outbsync(ide_drive_t *drive, u8 addr, unsigned long port) -{ - etrax100_ide_outw(addr, port); -} - -unsigned short -etrax100_ide_inw(unsigned long reg) { - int status; - int timeleft; - - timeleft = IDE_REGISTER_TIMEOUT; - /* wait for busy flag */ - while(timeleft && (*R_ATA_STATUS_DATA & IO_MASK(R_ATA_STATUS_DATA, busy))) - timeleft--; - - if(!timeleft) { - /* - * If we're asked to read the status register, like for - * example when a command does not complete for an - * extended time, but the ATA interface is stuck in a - * busy state at the *ETRAX* ATA interface level (as has - * happened repeatedly with at least one bad disk), then - * the best thing to do is to pretend that we read - * "busy" in the status register, so the IDE driver will - * time-out, abort the ongoing command and perform a - * reset sequence. Note that the subsequent OUT_BYTE - * call will also timeout on busy, but as long as the - * write is still performed, everything will be fine. - */ - if ((reg & IO_MASK (R_ATA_CTRL_DATA, addr)) - == IO_FIELD (R_ATA_CTRL_DATA, addr, IDE_STATUS_OFFSET)) - return BUSY_STAT; - else - /* For other rare cases we assume 0 is good enough. */ - return 0; - } - - *R_ATA_CTRL_DATA = reg | IO_STATE(R_ATA_CTRL_DATA, rw, read); /* read data */ - - timeleft = IDE_REGISTER_TIMEOUT; - /* wait for available */ - while(timeleft && !((status = *R_ATA_STATUS_DATA) & - IO_MASK(R_ATA_STATUS_DATA, dav))) - timeleft--; - - if(!timeleft) - return 0; - - LOWDB(printk("inb: 0x%x from reg 0x%x\n", status & 0xff, reg)); - - return (unsigned short)status; -} - -unsigned char -etrax100_ide_inb(unsigned long reg) -{ - return (unsigned char)etrax100_ide_inw(reg); -} - -/* PIO timing (in R_ATA_CONFIG) - * - * _____________________________ - * ADDRESS : ________/ - * - * _______________ - * DIOR : ____________/ \__________ - * - * _______________ - * DATA : XXXXXXXXXXXXXXXX_______________XXXXXXXX - * - * - * DIOR is unbuffered while address and data is buffered. - * This creates two problems: - * 1. The DIOR pulse is to early (because it is unbuffered) - * 2. The rise time of DIOR is long - * - * There are at least three different plausible solutions - * 1. Use a pad capable of larger currents in Etrax - * 2. Use an external buffer - * 3. Make the strobe pulse longer - * - * Some of the strobe timings below are modified to compensate - * for this. This implies a slight performance decrease. - * - * THIS SHOULD NEVER BE CHANGED! - * - * TODO: Is this true for the latest LX boards still ? - */ - -#define ATA_DMA2_STROBE 4 -#define ATA_DMA2_HOLD 0 -#define ATA_DMA1_STROBE 4 -#define ATA_DMA1_HOLD 1 -#define ATA_DMA0_STROBE 12 -#define ATA_DMA0_HOLD 9 -#define ATA_PIO4_SETUP 1 -#define ATA_PIO4_STROBE 5 -#define ATA_PIO4_HOLD 0 -#define ATA_PIO3_SETUP 1 -#define ATA_PIO3_STROBE 5 -#define ATA_PIO3_HOLD 1 -#define ATA_PIO2_SETUP 1 -#define ATA_PIO2_STROBE 6 -#define ATA_PIO2_HOLD 2 -#define ATA_PIO1_SETUP 2 -#define ATA_PIO1_STROBE 11 -#define ATA_PIO1_HOLD 4 -#define ATA_PIO0_SETUP 4 -#define ATA_PIO0_STROBE 19 -#define ATA_PIO0_HOLD 4 - -static int e100_dma_check (ide_drive_t *drive); -static void e100_dma_start(ide_drive_t *drive); -static int e100_dma_end (ide_drive_t *drive); -static void e100_ide_input_data (ide_drive_t *drive, void *, unsigned int); -static void e100_ide_output_data (ide_drive_t *drive, void *, unsigned int); -static void e100_atapi_input_bytes(ide_drive_t *drive, void *, unsigned int); -static void e100_atapi_output_bytes(ide_drive_t *drive, void *, unsigned int); -static int e100_dma_off (ide_drive_t *drive); - - -/* - * good_dma_drives() lists the model names (from "hdparm -i") - * of drives which do not support mword2 DMA but which are - * known to work fine with this interface under Linux. - */ - -const char *good_dma_drives[] = {"Micropolis 2112A", - "CONNER CTMA 4000", - "CONNER CTT8000-A", - NULL}; - -static void tune_e100_ide(ide_drive_t *drive, byte pio) -{ - pio = 4; - /* pio = ide_get_best_pio_mode(drive, pio, 4, NULL); */ - - /* set pio mode! */ - - switch(pio) { - case 0: - *R_ATA_CONFIG = ( IO_FIELD( R_ATA_CONFIG, enable, 1 ) | - IO_FIELD( R_ATA_CONFIG, dma_strobe, ATA_DMA2_STROBE ) | - IO_FIELD( R_ATA_CONFIG, dma_hold, ATA_DMA2_HOLD ) | - IO_FIELD( R_ATA_CONFIG, pio_setup, ATA_PIO0_SETUP ) | - IO_FIELD( R_ATA_CONFIG, pio_strobe, ATA_PIO0_STROBE ) | - IO_FIELD( R_ATA_CONFIG, pio_hold, ATA_PIO0_HOLD ) ); - break; - case 1: - *R_ATA_CONFIG = ( IO_FIELD( R_ATA_CONFIG, enable, 1 ) | - IO_FIELD( R_ATA_CONFIG, dma_strobe, ATA_DMA2_STROBE ) | - IO_FIELD( R_ATA_CONFIG, dma_hold, ATA_DMA2_HOLD ) | - IO_FIELD( R_ATA_CONFIG, pio_setup, ATA_PIO1_SETUP ) | - IO_FIELD( R_ATA_CONFIG, pio_strobe, ATA_PIO1_STROBE ) | - IO_FIELD( R_ATA_CONFIG, pio_hold, ATA_PIO1_HOLD ) ); - break; - case 2: - *R_ATA_CONFIG = ( IO_FIELD( R_ATA_CONFIG, enable, 1 ) | - IO_FIELD( R_ATA_CONFIG, dma_strobe, ATA_DMA2_STROBE ) | - IO_FIELD( R_ATA_CONFIG, dma_hold, ATA_DMA2_HOLD ) | - IO_FIELD( R_ATA_CONFIG, pio_setup, ATA_PIO2_SETUP ) | - IO_FIELD( R_ATA_CONFIG, pio_strobe, ATA_PIO2_STROBE ) | - IO_FIELD( R_ATA_CONFIG, pio_hold, ATA_PIO2_HOLD ) ); - break; - case 3: - *R_ATA_CONFIG = ( IO_FIELD( R_ATA_CONFIG, enable, 1 ) | - IO_FIELD( R_ATA_CONFIG, dma_strobe, ATA_DMA2_STROBE ) | - IO_FIELD( R_ATA_CONFIG, dma_hold, ATA_DMA2_HOLD ) | - IO_FIELD( R_ATA_CONFIG, pio_setup, ATA_PIO3_SETUP ) | - IO_FIELD( R_ATA_CONFIG, pio_strobe, ATA_PIO3_STROBE ) | - IO_FIELD( R_ATA_CONFIG, pio_hold, ATA_PIO3_HOLD ) ); - break; - case 4: - *R_ATA_CONFIG = ( IO_FIELD( R_ATA_CONFIG, enable, 1 ) | - IO_FIELD( R_ATA_CONFIG, dma_strobe, ATA_DMA2_STROBE ) | - IO_FIELD( R_ATA_CONFIG, dma_hold, ATA_DMA2_HOLD ) | - IO_FIELD( R_ATA_CONFIG, pio_setup, ATA_PIO4_SETUP ) | - IO_FIELD( R_ATA_CONFIG, pio_strobe, ATA_PIO4_STROBE ) | - IO_FIELD( R_ATA_CONFIG, pio_hold, ATA_PIO4_HOLD ) ); - break; - } -} - -static int e100_dma_setup(ide_drive_t *drive) -{ - struct request *rq = drive->hwif->hwgroup->rq; - - if (rq_data_dir(rq)) { - e100_read_command = 0; - - RESET_DMA(ATA_TX_DMA_NBR); /* sometimes the DMA channel get stuck so we need to do this */ - WAIT_DMA(ATA_TX_DMA_NBR); - } else { - e100_read_command = 1; - - RESET_DMA(ATA_RX_DMA_NBR); /* sometimes the DMA channel get stuck so we need to do this */ - WAIT_DMA(ATA_RX_DMA_NBR); - } - - /* set up the Etrax DMA descriptors */ - if (e100_ide_build_dmatable(drive)) { - ide_map_sg(drive, rq); - return 1; - } - - return 0; -} - -static void e100_dma_exec_cmd(ide_drive_t *drive, u8 command) -{ - /* set the irq handler which will finish the request when DMA is done */ - ide_set_handler(drive, &etrax_dma_intr, WAIT_CMD, NULL); - - /* issue cmd to drive */ - etrax100_ide_outb(command, IDE_COMMAND_REG); -} - -void __init -init_e100_ide (void) -{ - volatile unsigned int dummy; - int h; - - printk("ide: ETRAX 100LX built-in ATA DMA controller\n"); - - /* first fill in some stuff in the ide_hwifs fields */ - - for(h = 0; h < MAX_HWIFS; h++) { - ide_hwif_t *hwif = &ide_hwifs[h]; - hwif->mmio = 2; - hwif->chipset = ide_etrax100; - hwif->tuneproc = &tune_e100_ide; - hwif->ata_input_data = &e100_ide_input_data; - hwif->ata_output_data = &e100_ide_output_data; - hwif->atapi_input_bytes = &e100_atapi_input_bytes; - hwif->atapi_output_bytes = &e100_atapi_output_bytes; - hwif->ide_dma_check = &e100_dma_check; - hwif->ide_dma_end = &e100_dma_end; - hwif->dma_setup = &e100_dma_setup; - hwif->dma_exec_cmd = &e100_dma_exec_cmd; - hwif->dma_start = &e100_dma_start; - hwif->OUTB = &etrax100_ide_outb; - hwif->OUTW = &etrax100_ide_outw; - hwif->OUTBSYNC = &etrax100_ide_outbsync; - hwif->INB = &etrax100_ide_inb; - hwif->INW = &etrax100_ide_inw; - hwif->ide_dma_off_quietly = &e100_dma_off; - } - - /* actually reset and configure the etrax100 ide/ata interface */ - - *R_ATA_CTRL_DATA = 0; - *R_ATA_TRANSFER_CNT = 0; - *R_ATA_CONFIG = 0; - - genconfig_shadow = (genconfig_shadow & - ~IO_MASK(R_GEN_CONFIG, dma2) & - ~IO_MASK(R_GEN_CONFIG, dma3) & - ~IO_MASK(R_GEN_CONFIG, ata)) | - ( IO_STATE( R_GEN_CONFIG, dma3, ata ) | - IO_STATE( R_GEN_CONFIG, dma2, ata ) | - IO_STATE( R_GEN_CONFIG, ata, select ) ); - - *R_GEN_CONFIG = genconfig_shadow; - - /* pull the chosen /reset-line low */ - -#ifdef CONFIG_ETRAX_IDE_G27_RESET - REG_SHADOW_SET(R_PORT_G_DATA, port_g_data_shadow, 27, 0); -#endif -#ifdef CONFIG_ETRAX_IDE_CSE1_16_RESET - REG_SHADOW_SET(port_cse1_addr, port_cse1_shadow, 16, 0); -#endif -#ifdef CONFIG_ETRAX_IDE_CSP0_8_RESET - REG_SHADOW_SET(port_csp0_addr, port_csp0_shadow, 8, 0); -#endif -#ifdef CONFIG_ETRAX_IDE_PB7_RESET - port_pb_dir_shadow = port_pb_dir_shadow | - IO_STATE(R_PORT_PB_DIR, dir7, output); - *R_PORT_PB_DIR = port_pb_dir_shadow; - REG_SHADOW_SET(R_PORT_PB_DATA, port_pb_data_shadow, 7, 1); -#endif - - /* wait some */ - - udelay(25); - - /* de-assert bus-reset */ - -#ifdef CONFIG_ETRAX_IDE_CSE1_16_RESET - REG_SHADOW_SET(port_cse1_addr, port_cse1_shadow, 16, 1); -#endif -#ifdef CONFIG_ETRAX_IDE_CSP0_8_RESET - REG_SHADOW_SET(port_csp0_addr, port_csp0_shadow, 8, 1); -#endif -#ifdef CONFIG_ETRAX_IDE_G27_RESET - REG_SHADOW_SET(R_PORT_G_DATA, port_g_data_shadow, 27, 1); -#endif - - /* make a dummy read to set the ata controller in a proper state */ - dummy = *R_ATA_STATUS_DATA; - - *R_ATA_CONFIG = ( IO_FIELD( R_ATA_CONFIG, enable, 1 ) | - IO_FIELD( R_ATA_CONFIG, dma_strobe, ATA_DMA2_STROBE ) | - IO_FIELD( R_ATA_CONFIG, dma_hold, ATA_DMA2_HOLD ) | - IO_FIELD( R_ATA_CONFIG, pio_setup, ATA_PIO4_SETUP ) | - IO_FIELD( R_ATA_CONFIG, pio_strobe, ATA_PIO4_STROBE ) | - IO_FIELD( R_ATA_CONFIG, pio_hold, ATA_PIO4_HOLD ) ); - - *R_ATA_CTRL_DATA = ( IO_STATE( R_ATA_CTRL_DATA, rw, read) | - IO_FIELD( R_ATA_CTRL_DATA, addr, 1 ) ); - - while(*R_ATA_STATUS_DATA & IO_MASK(R_ATA_STATUS_DATA, busy)); /* wait for busy flag*/ - - *R_IRQ_MASK0_SET = ( IO_STATE( R_IRQ_MASK0_SET, ata_irq0, set ) | - IO_STATE( R_IRQ_MASK0_SET, ata_irq1, set ) | - IO_STATE( R_IRQ_MASK0_SET, ata_irq2, set ) | - IO_STATE( R_IRQ_MASK0_SET, ata_irq3, set ) ); - - printk("ide: waiting %d seconds for drives to regain consciousness\n", - CONFIG_ETRAX_IDE_DELAY); - - h = jiffies + (CONFIG_ETRAX_IDE_DELAY * HZ); - while(time_before(jiffies, h)) /* nothing */ ; - - /* reset the dma channels we will use */ - - RESET_DMA(ATA_TX_DMA_NBR); - RESET_DMA(ATA_RX_DMA_NBR); - WAIT_DMA(ATA_TX_DMA_NBR); - WAIT_DMA(ATA_RX_DMA_NBR); - -} - -static int e100_dma_off (ide_drive_t *drive) -{ - return 0; -} - -static etrax_dma_descr mydescr; - -/* - * The following routines are mainly used by the ATAPI drivers. - * - * These routines will round up any request for an odd number of bytes, - * so if an odd bytecount is specified, be sure that there's at least one - * extra byte allocated for the buffer. - */ -static void -e100_atapi_input_bytes (ide_drive_t *drive, void *buffer, unsigned int bytecount) -{ - unsigned long data_reg = IDE_DATA_REG; - - D(printk("atapi_input_bytes, dreg 0x%x, buffer 0x%x, count %d\n", - data_reg, buffer, bytecount)); - - if(bytecount & 1) { - printk("warning, odd bytecount in cdrom_in_bytes = %d.\n", bytecount); - bytecount++; /* to round off */ - } - - /* make sure the DMA channel is available */ - RESET_DMA(ATA_RX_DMA_NBR); - WAIT_DMA(ATA_RX_DMA_NBR); - - /* setup DMA descriptor */ - - mydescr.sw_len = bytecount; - mydescr.ctrl = d_eol; - mydescr.buf = virt_to_phys(buffer); - - /* start the dma channel */ - - *R_DMA_CH3_FIRST = virt_to_phys(&mydescr); - *R_DMA_CH3_CMD = IO_STATE(R_DMA_CH3_CMD, cmd, start); - - /* initiate a multi word dma read using PIO handshaking */ - - *R_ATA_TRANSFER_CNT = IO_FIELD(R_ATA_TRANSFER_CNT, count, bytecount >> 1); - - *R_ATA_CTRL_DATA = data_reg | - IO_STATE(R_ATA_CTRL_DATA, rw, read) | - IO_STATE(R_ATA_CTRL_DATA, src_dst, dma) | - IO_STATE(R_ATA_CTRL_DATA, handsh, pio) | - IO_STATE(R_ATA_CTRL_DATA, multi, on) | - IO_STATE(R_ATA_CTRL_DATA, dma_size, word); - - /* wait for completion */ - - LED_DISK_READ(1); - WAIT_DMA(ATA_RX_DMA_NBR); - LED_DISK_READ(0); - -#if 0 - /* old polled transfer code - * this should be moved into a new function that can do polled - * transfers if DMA is not available - */ - - /* initiate a multi word read */ - - *R_ATA_TRANSFER_CNT = wcount << 1; - - *R_ATA_CTRL_DATA = data_reg | - IO_STATE(R_ATA_CTRL_DATA, rw, read) | - IO_STATE(R_ATA_CTRL_DATA, src_dst, register) | - IO_STATE(R_ATA_CTRL_DATA, handsh, pio) | - IO_STATE(R_ATA_CTRL_DATA, multi, on) | - IO_STATE(R_ATA_CTRL_DATA, dma_size, word); - - /* svinto has a latency until the busy bit actually is set */ - - nop(); nop(); - nop(); nop(); - nop(); nop(); - nop(); nop(); - nop(); nop(); - - /* unit should be busy during multi transfer */ - while((status = *R_ATA_STATUS_DATA) & IO_MASK(R_ATA_STATUS_DATA, busy)) { - while(!(status & IO_MASK(R_ATA_STATUS_DATA, dav))) - status = *R_ATA_STATUS_DATA; - *ptr++ = (unsigned short)(status & 0xffff); - } -#endif -} - -static void -e100_atapi_output_bytes (ide_drive_t *drive, void *buffer, unsigned int bytecount) -{ - unsigned long data_reg = IDE_DATA_REG; - - D(printk("atapi_output_bytes, dreg 0x%x, buffer 0x%x, count %d\n", - data_reg, buffer, bytecount)); - - if(bytecount & 1) { - printk("odd bytecount %d in atapi_out_bytes!\n", bytecount); - bytecount++; - } - - /* make sure the DMA channel is available */ - RESET_DMA(ATA_TX_DMA_NBR); - WAIT_DMA(ATA_TX_DMA_NBR); - - /* setup DMA descriptor */ - - mydescr.sw_len = bytecount; - mydescr.ctrl = d_eol; - mydescr.buf = virt_to_phys(buffer); - - /* start the dma channel */ - - *R_DMA_CH2_FIRST = virt_to_phys(&mydescr); - *R_DMA_CH2_CMD = IO_STATE(R_DMA_CH2_CMD, cmd, start); - - /* initiate a multi word dma write using PIO handshaking */ - - *R_ATA_TRANSFER_CNT = IO_FIELD(R_ATA_TRANSFER_CNT, count, bytecount >> 1); - - *R_ATA_CTRL_DATA = data_reg | - IO_STATE(R_ATA_CTRL_DATA, rw, write) | - IO_STATE(R_ATA_CTRL_DATA, src_dst, dma) | - IO_STATE(R_ATA_CTRL_DATA, handsh, pio) | - IO_STATE(R_ATA_CTRL_DATA, multi, on) | - IO_STATE(R_ATA_CTRL_DATA, dma_size, word); - - /* wait for completion */ - - LED_DISK_WRITE(1); - WAIT_DMA(ATA_TX_DMA_NBR); - LED_DISK_WRITE(0); - -#if 0 - /* old polled write code - see comment in input_bytes */ - - /* wait for busy flag */ - while(*R_ATA_STATUS_DATA & IO_MASK(R_ATA_STATUS_DATA, busy)); - - /* initiate a multi word write */ - - *R_ATA_TRANSFER_CNT = bytecount >> 1; - - ctrl = data_reg | - IO_STATE(R_ATA_CTRL_DATA, rw, write) | - IO_STATE(R_ATA_CTRL_DATA, src_dst, register) | - IO_STATE(R_ATA_CTRL_DATA, handsh, pio) | - IO_STATE(R_ATA_CTRL_DATA, multi, on) | - IO_STATE(R_ATA_CTRL_DATA, dma_size, word); - - LED_DISK_WRITE(1); - - /* Etrax will set busy = 1 until the multi pio transfer has finished - * and tr_rdy = 1 after each successful word transfer. - * When the last byte has been transferred Etrax will first set tr_tdy = 1 - * and then busy = 0 (not in the same cycle). If we read busy before it - * has been set to 0 we will think that we should transfer more bytes - * and then tr_rdy would be 0 forever. This is solved by checking busy - * in the inner loop. - */ - - do { - *R_ATA_CTRL_DATA = ctrl | *ptr++; - while(!(*R_ATA_STATUS_DATA & IO_MASK(R_ATA_STATUS_DATA, tr_rdy)) && - (*R_ATA_STATUS_DATA & IO_MASK(R_ATA_STATUS_DATA, busy))); - } while(*R_ATA_STATUS_DATA & IO_MASK(R_ATA_STATUS_DATA, busy)); - - LED_DISK_WRITE(0); -#endif - -} - -/* - * This is used for most PIO data transfers *from* the IDE interface - */ -static void -e100_ide_input_data (ide_drive_t *drive, void *buffer, unsigned int wcount) -{ - e100_atapi_input_bytes(drive, buffer, wcount << 2); -} - -/* - * This is used for most PIO data transfers *to* the IDE interface - */ -static void -e100_ide_output_data (ide_drive_t *drive, void *buffer, unsigned int wcount) -{ - e100_atapi_output_bytes(drive, buffer, wcount << 2); -} - -/* we only have one DMA channel on the chip for ATA, so we can keep these statically */ -static etrax_dma_descr ata_descrs[MAX_DMA_DESCRS]; -static unsigned int ata_tot_size; - -/* - * e100_ide_build_dmatable() prepares a dma request. - * Returns 0 if all went okay, returns 1 otherwise. - */ -static int e100_ide_build_dmatable (ide_drive_t *drive) -{ - ide_hwif_t *hwif = HWIF(drive); - struct scatterlist* sg; - struct request *rq = HWGROUP(drive)->rq; - unsigned long size, addr; - unsigned int count = 0; - int i = 0; - - sg = hwif->sg_table; - - ata_tot_size = 0; - - ide_map_sg(drive, rq); - - i = hwif->sg_nents; - - while(i) { - /* - * Determine addr and size of next buffer area. We assume that - * individual virtual buffers are always composed linearly in - * physical memory. For example, we assume that any 8kB buffer - * is always composed of two adjacent physical 4kB pages rather - * than two possibly non-adjacent physical 4kB pages. - */ - /* group sequential buffers into one large buffer */ - addr = page_to_phys(sg->page) + sg->offset; - size = sg_dma_len(sg); - while (sg++, --i) { - if ((addr + size) != page_to_phys(sg->page) + sg->offset) - break; - size += sg_dma_len(sg); - } - - /* did we run out of descriptors? */ - - if(count >= MAX_DMA_DESCRS) { - printk("%s: too few DMA descriptors\n", drive->name); - return 1; - } - - /* however, this case is more difficult - R_ATA_TRANSFER_CNT cannot be more - than 65536 words per transfer, so in that case we need to either - 1) use a DMA interrupt to re-trigger R_ATA_TRANSFER_CNT and continue with - the descriptors, or - 2) simply do the request here, and get dma_intr to only ide_end_request on - those blocks that were actually set-up for transfer. - */ - - if(ata_tot_size + size > 131072) { - printk("too large total ATA DMA request, %d + %d!\n", ata_tot_size, (int)size); - return 1; - } - - /* If size > 65536 it has to be splitted into new descriptors. Since we don't handle - size > 131072 only one split is necessary */ - - if(size > 65536) { - /* ok we want to do IO at addr, size bytes. set up a new descriptor entry */ - ata_descrs[count].sw_len = 0; /* 0 means 65536, this is a 16-bit field */ - ata_descrs[count].ctrl = 0; - ata_descrs[count].buf = addr; - ata_descrs[count].next = virt_to_phys(&ata_descrs[count + 1]); - count++; - ata_tot_size += 65536; - /* size and addr should refere to not handled data */ - size -= 65536; - addr += 65536; - } - /* ok we want to do IO at addr, size bytes. set up a new descriptor entry */ - if(size == 65536) { - ata_descrs[count].sw_len = 0; /* 0 means 65536, this is a 16-bit field */ - } else { - ata_descrs[count].sw_len = size; - } - ata_descrs[count].ctrl = 0; - ata_descrs[count].buf = addr; - ata_descrs[count].next = virt_to_phys(&ata_descrs[count + 1]); - count++; - ata_tot_size += size; - } - - if (count) { - /* set the end-of-list flag on the last descriptor */ - ata_descrs[count - 1].ctrl |= d_eol; - /* return and say all is ok */ - return 0; - } - - printk("%s: empty DMA table?\n", drive->name); - return 1; /* let the PIO routines handle this weirdness */ -} - -static int config_drive_for_dma (ide_drive_t *drive) -{ - const char **list; - struct hd_driveid *id = drive->id; - - if (id && (id->capability & 1)) { - /* Enable DMA on any drive that supports mword2 DMA */ - if ((id->field_valid & 2) && (id->dma_mword & 0x404) == 0x404) { - drive->using_dma = 1; - return 0; /* DMA enabled */ - } - - /* Consult the list of known "good" drives */ - list = good_dma_drives; - while (*list) { - if (!strcmp(*list++,id->model)) { - drive->using_dma = 1; - return 0; /* DMA enabled */ - } - } - } - return 1; /* DMA not enabled */ -} - -/* - * etrax_dma_intr() is the handler for disk read/write DMA interrupts - */ -static ide_startstop_t etrax_dma_intr (ide_drive_t *drive) -{ - LED_DISK_READ(0); - LED_DISK_WRITE(0); - - return ide_dma_intr(drive); -} - -/* - * Functions below initiates/aborts DMA read/write operations on a drive. - * - * The caller is assumed to have selected the drive and programmed the drive's - * sector address using CHS or LBA. All that remains is to prepare for DMA - * and then issue the actual read/write DMA/PIO command to the drive. - * - * Returns 0 if all went well. - * Returns 1 if DMA read/write could not be started, in which case - * the caller should revert to PIO for the current request. - */ - -static int e100_dma_check(ide_drive_t *drive) -{ - return config_drive_for_dma (drive); -} - -static int e100_dma_end(ide_drive_t *drive) -{ - /* TODO: check if something went wrong with the DMA */ - return 0; -} - -static void e100_dma_start(ide_drive_t *drive) -{ - if (e100_read_command) { - /* begin DMA */ - - /* need to do this before RX DMA due to a chip bug - * it is enough to just flush the part of the cache that - * corresponds to the buffers we start, but since HD transfers - * usually are more than 8 kB, it is easier to optimize for the - * normal case and just flush the entire cache. its the only - * way to be sure! (OB movie quote) - */ - flush_etrax_cache(); - *R_DMA_CH3_FIRST = virt_to_phys(ata_descrs); - *R_DMA_CH3_CMD = IO_STATE(R_DMA_CH3_CMD, cmd, start); - - /* initiate a multi word dma read using DMA handshaking */ - - *R_ATA_TRANSFER_CNT = - IO_FIELD(R_ATA_TRANSFER_CNT, count, ata_tot_size >> 1); - - *R_ATA_CTRL_DATA = - IO_FIELD(R_ATA_CTRL_DATA, data, IDE_DATA_REG) | - IO_STATE(R_ATA_CTRL_DATA, rw, read) | - IO_STATE(R_ATA_CTRL_DATA, src_dst, dma) | - IO_STATE(R_ATA_CTRL_DATA, handsh, dma) | - IO_STATE(R_ATA_CTRL_DATA, multi, on) | - IO_STATE(R_ATA_CTRL_DATA, dma_size, word); - - LED_DISK_READ(1); - - D(printk("dma read of %d bytes.\n", ata_tot_size)); - - } else { - /* writing */ - /* begin DMA */ - - *R_DMA_CH2_FIRST = virt_to_phys(ata_descrs); - *R_DMA_CH2_CMD = IO_STATE(R_DMA_CH2_CMD, cmd, start); - - /* initiate a multi word dma write using DMA handshaking */ - - *R_ATA_TRANSFER_CNT = - IO_FIELD(R_ATA_TRANSFER_CNT, count, ata_tot_size >> 1); - - *R_ATA_CTRL_DATA = - IO_FIELD(R_ATA_CTRL_DATA, data, IDE_DATA_REG) | - IO_STATE(R_ATA_CTRL_DATA, rw, write) | - IO_STATE(R_ATA_CTRL_DATA, src_dst, dma) | - IO_STATE(R_ATA_CTRL_DATA, handsh, dma) | - IO_STATE(R_ATA_CTRL_DATA, multi, on) | - IO_STATE(R_ATA_CTRL_DATA, dma_size, word); - - LED_DISK_WRITE(1); - - D(printk("dma write of %d bytes.\n", ata_tot_size)); - } -} |