Merge branch 'master' into next

Conflicts:
	fs/cifs/misc.c

Merge to resolve above, per the patch below.

Signed-off-by: James Morris <jmorris@namei.org>

diff --cc fs/cifs/misc.c
index ec36410,addd1dc..0000000
--- a/fs/cifs/misc.c
+++ b/fs/cifs/misc.c
@@@ -347,13 -338,13 +338,13 @@@ header_assemble(struct smb_hdr *buffer
  		/*  BB Add support for establishing new tCon and SMB Session  */
  		/*      with userid/password pairs found on the smb session   */
  		/*	for other target tcp/ip addresses 		BB    */
 -				if (current->fsuid != treeCon->ses->linux_uid) {
 +				if (current_fsuid() != treeCon->ses->linux_uid) {
  					cFYI(1, ("Multiuser mode and UID "
  						 "did not match tcon uid"));
- 					read_lock(&GlobalSMBSeslock);
- 					list_for_each(temp_item, &GlobalSMBSessionList) {
- 						ses = list_entry(temp_item, struct cifsSesInfo, cifsSessionList);
+ 					read_lock(&cifs_tcp_ses_lock);
+ 					list_for_each(temp_item, &treeCon->ses->server->smb_ses_list) {
+ 						ses = list_entry(temp_item, struct cifsSesInfo, smb_ses_list);
 -						if (ses->linux_uid == current->fsuid) {
 +						if (ses->linux_uid == current_fsuid()) {
  							if (ses->server == treeCon->ses->server) {
  								cFYI(1, ("found matching uid substitute right smb_uid"));
  								buffer->Uid = ses->Suid;

1 files changed, 6 insertions, 17 deletions

diff --git a/drivers/usb/host/Kconfig b/drivers/usb/host/Kconfig
index 56f592dc0b3..f3a75a929e0 100644
--- a/drivers/usb/host/Kconfig
+++ b/drivers/usb/host/Kconfig
@@ -110,29 +110,18 @@ config USB_ISP116X_HCD
 
 config USB_ISP1760_HCD
 	tristate "ISP 1760 HCD support"
-	depends on USB && EXPERIMENTAL
+	depends on USB && EXPERIMENTAL && (PCI || PPC_OF)
 	---help---
 	  The ISP1760 chip is a USB 2.0 host controller.
 
 	  This driver does not support isochronous transfers or OTG.
+	  This USB controller is usually attached to a non-DMA-Master
+	  capable bus. NXP's eval kit brings this chip on PCI card
+	  where the chip itself is behind a PLB to simulate such
+	  a bus.
 
 	  To compile this driver as a module, choose M here: the
-	  module will be called isp1760-hcd.
-
-config USB_ISP1760_PCI
-	bool "Support for the PCI bus"
-	depends on USB_ISP1760_HCD && PCI
-	---help---
-	  Enables support for the device present on the PCI bus.
-	  This should only be required if you happen to have the eval kit from
-	  NXP and you are going to test it.
-
-config USB_ISP1760_OF
-	bool "Support for the OF platform bus"
-	depends on USB_ISP1760_HCD && PPC_OF
-	---help---
-	  Enables support for the device present on the PowerPC
-	  OpenFirmware platform bus.
+	  module will be called isp1760.
 
 config USB_OHCI_HCD
 	tristate "OHCI HCD support"