diff options
369 files changed, 29752 insertions, 7620 deletions
diff --git a/Documentation/kernel-parameters.txt b/Documentation/kernel-parameters.txt index e07c432c731..f1e970acad4 100644 --- a/Documentation/kernel-parameters.txt +++ b/Documentation/kernel-parameters.txt @@ -1208,6 +1208,11 @@ and is between 256 and 4096 characters. It is defined in the file mtdparts= [MTD] See drivers/mtd/cmdlinepart.c. + mtdset= [ARM] + ARM/S3C2412 JIVE boot control + + See arch/arm/mach-s3c2412/mach-jive.c + mtouchusb.raw_coordinates= [HW] Make the MicroTouch USB driver use raw coordinates ('y', default) or cooked coordinates ('n') diff --git a/arch/arm/Kconfig b/arch/arm/Kconfig index 8a9a84c4adf..3d9397ec746 100644 --- a/arch/arm/Kconfig +++ b/arch/arm/Kconfig @@ -84,6 +84,11 @@ config STACKTRACE_SUPPORT bool default y +config HAVE_LATENCYTOP_SUPPORT + bool + depends on !SMP + default y + config LOCKDEP_SUPPORT bool default y @@ -147,6 +152,10 @@ config FIQ config ARCH_MTD_XIP bool +config GENERIC_HARDIRQS_NO__DO_IRQ + bool + def_bool y + if OPROFILE config OPROFILE_ARMV6 @@ -232,13 +241,6 @@ config ARCH_CLPS711X help Support for Cirrus Logic 711x/721x based boards. -config ARCH_CO285 - bool "Co-EBSA285" - select FOOTBRIDGE - select FOOTBRIDGE_ADDIN - help - Support for Intel's EBSA285 companion chip. - config ARCH_EBSA110 bool "EBSA-110" select ISA @@ -299,6 +301,8 @@ config ARCH_IOP32X depends on MMU select PLAT_IOP select PCI + select GENERIC_GPIO + select HAVE_GPIO_LIB help Support for Intel's 80219 and IOP32X (XScale) family of processors. @@ -308,6 +312,8 @@ config ARCH_IOP33X depends on MMU select PLAT_IOP select PCI + select GENERIC_GPIO + select HAVE_GPIO_LIB help Support for Intel's IOP33X (XScale) family of processors. @@ -347,6 +353,16 @@ config ARCH_L7200 If you have any questions or comments about the Linux kernel port to this board, send e-mail to <sjhill@cotw.com>. +config ARCH_KIRKWOOD + bool "Marvell Kirkwood" + select PCI + select GENERIC_TIME + select GENERIC_CLOCKEVENTS + select PLAT_ORION + help + Support for the following Marvell Kirkwood series SoCs: + 88F6180, 88F6192 and 88F6281. + config ARCH_KS8695 bool "Micrel/Kendin KS8695" select GENERIC_GPIO @@ -365,6 +381,24 @@ config ARCH_NS9XXX <http://www.digi.com/products/microprocessors/index.jsp> +config ARCH_LOKI + bool "Marvell Loki (88RC8480)" + select GENERIC_TIME + select GENERIC_CLOCKEVENTS + select PLAT_ORION + help + Support for the Marvell Loki (88RC8480) SoC. + +config ARCH_MV78XX0 + bool "Marvell MV78xx0" + select PCI + select GENERIC_TIME + select GENERIC_CLOCKEVENTS + select PLAT_ORION + help + Support for the following Marvell MV78xx0 series SoCs: + MV781x0, MV782x0. + config ARCH_MXC bool "Freescale MXC/iMX-based" select GENERIC_TIME @@ -385,7 +419,8 @@ config ARCH_ORION5X select PLAT_ORION help Support for the following Marvell Orion 5x series SoCs: - Orion-1 (5181), Orion-NAS (5182), Orion-2 (5281.) + Orion-1 (5181), Orion-VoIP (5181L), Orion-NAS (5182), + Orion-2 (5281). config ARCH_PNX4008 bool "Philips Nexperia PNX4008 Mobile" @@ -410,6 +445,7 @@ config ARCH_RPC select FIQ select TIMER_ACORN select ARCH_MAY_HAVE_PC_FDC + select HAVE_PATA_PLATFORM select ISA_DMA_API select NO_IOPORT help @@ -506,6 +542,10 @@ source "arch/arm/mach-ixp2000/Kconfig" source "arch/arm/mach-ixp23xx/Kconfig" +source "arch/arm/mach-loki/Kconfig" + +source "arch/arm/mach-mv78xx0/Kconfig" + source "arch/arm/mach-pxa/Kconfig" source "arch/arm/mach-sa1100/Kconfig" @@ -518,6 +558,8 @@ source "arch/arm/mach-omap2/Kconfig" source "arch/arm/mach-orion5x/Kconfig" +source "arch/arm/mach-kirkwood/Kconfig" + source "arch/arm/plat-s3c24xx/Kconfig" source "arch/arm/plat-s3c/Kconfig" @@ -707,27 +749,6 @@ config PREEMPT Say Y here if you are building a kernel for a desktop, embedded or real-time system. Say N if you are unsure. -config NO_IDLE_HZ - bool "Dynamic tick timer" - depends on !GENERIC_CLOCKEVENTS - help - Select this option if you want to disable continuous timer ticks - and have them programmed to occur as required. This option saves - power as the system can remain in idle state for longer. - - By default dynamic tick is disabled during the boot, and can be - manually enabled with: - - echo 1 > /sys/devices/system/timer/timer0/dyn_tick - - Alternatively, if you want dynamic tick automatically enabled - during boot, pass "dyntick=enable" via the kernel command string. - - Please note that dynamic tick may affect the accuracy of - timekeeping on some platforms depending on the implementation. - Currently at least OMAP, PXA2xx and SA11x0 platforms are known - to have accurate timekeeping with dynamic tick. - config HZ int default 128 if ARCH_L7200 @@ -793,7 +814,7 @@ source "mm/Kconfig" config LEDS bool "Timer and CPU usage LEDs" - depends on ARCH_CDB89712 || ARCH_CO285 || ARCH_EBSA110 || \ + depends on ARCH_CDB89712 || ARCH_EBSA110 || \ ARCH_EBSA285 || ARCH_IMX || ARCH_INTEGRATOR || \ ARCH_LUBBOCK || MACH_MAINSTONE || ARCH_NETWINDER || \ ARCH_OMAP || ARCH_P720T || ARCH_PXA_IDP || \ diff --git a/arch/arm/Makefile b/arch/arm/Makefile index 009d4feb954..b20995a82e0 100644 --- a/arch/arm/Makefile +++ b/arch/arm/Makefile @@ -100,8 +100,6 @@ textofs-y := 0x00008000 incdir-$(CONFIG_ARCH_CLPS7500) := cl7500 machine-$(CONFIG_FOOTBRIDGE) := footbridge incdir-$(CONFIG_FOOTBRIDGE) := ebsa285 - machine-$(CONFIG_ARCH_CO285) := footbridge - incdir-$(CONFIG_ARCH_CO285) := ebsa285 machine-$(CONFIG_ARCH_SHARK) := shark machine-$(CONFIG_ARCH_SA1100) := sa1100 ifeq ($(CONFIG_ARCH_SA1100),y) @@ -135,12 +133,15 @@ endif machine-$(CONFIG_ARCH_NETX) := netx machine-$(CONFIG_ARCH_NS9XXX) := ns9xxx machine-$(CONFIG_ARCH_DAVINCI) := davinci + machine-$(CONFIG_ARCH_KIRKWOOD) := kirkwood machine-$(CONFIG_ARCH_KS8695) := ks8695 incdir-$(CONFIG_ARCH_MXC) := mxc machine-$(CONFIG_ARCH_MX2) := mx2 machine-$(CONFIG_ARCH_MX3) := mx3 machine-$(CONFIG_ARCH_ORION5X) := orion5x machine-$(CONFIG_ARCH_MSM7X00A) := msm + machine-$(CONFIG_ARCH_LOKI) := loki + machine-$(CONFIG_ARCH_MV78XX0) := mv78xx0 ifeq ($(CONFIG_ARCH_EBSA110),y) # This is what happens if you forget the IOCS16 line. @@ -191,8 +192,6 @@ core-$(CONFIG_PLAT_S3C24XX) += arch/arm/plat-s3c24xx/ core-$(CONFIG_ARCH_MXC) += arch/arm/plat-mxc/ drivers-$(CONFIG_OPROFILE) += arch/arm/oprofile/ -drivers-$(CONFIG_ARCH_CLPS7500) += drivers/acorn/char/ -drivers-$(CONFIG_ARCH_L7200) += drivers/acorn/char/ libs-y := arch/arm/lib/ $(libs-y) diff --git a/arch/arm/boot/compressed/head.S b/arch/arm/boot/compressed/head.S index 3c2c8f2a1dc..de41daeab5e 100644 --- a/arch/arm/boot/compressed/head.S +++ b/arch/arm/boot/compressed/head.S @@ -623,8 +623,8 @@ proc_types: b __armv4_mmu_cache_off b __armv4_mmu_cache_flush - .word 0x56055310 @ Feroceon - .word 0xfffffff0 + .word 0x56050000 @ Feroceon + .word 0xff0f0000 b __armv4_mmu_cache_on b __armv4_mmu_cache_off b __armv5tej_mmu_cache_flush diff --git a/arch/arm/common/Makefile b/arch/arm/common/Makefile index 3d0b9fa42f8..325e4b6a6af 100644 --- a/arch/arm/common/Makefile +++ b/arch/arm/common/Makefile @@ -2,7 +2,6 @@ # Makefile for the linux kernel. # -obj-y += rtctime.o obj-$(CONFIG_ARM_GIC) += gic.o obj-$(CONFIG_ARM_VIC) += vic.o obj-$(CONFIG_ICST525) += icst525.o diff --git a/arch/arm/common/rtctime.c b/arch/arm/common/rtctime.c deleted file mode 100644 index aa8f7739c82..00000000000 --- a/arch/arm/common/rtctime.c +++ /dev/null @@ -1,434 +0,0 @@ -/* - * linux/arch/arm/common/rtctime.c - * - * Copyright (C) 2003 Deep Blue Solutions Ltd. - * Based on sa1100-rtc.c, Nils Faerber, CIH, Nicolas Pitre. - * Based on rtc.c by Paul Gortmaker - * - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License version 2 as - * published by the Free Software Foundation. - */ -#include <linux/module.h> -#include <linux/kernel.h> -#include <linux/time.h> -#include <linux/rtc.h> -#include <linux/poll.h> -#include <linux/proc_fs.h> -#include <linux/miscdevice.h> -#include <linux/spinlock.h> -#include <linux/capability.h> -#include <linux/device.h> -#include <linux/mutex.h> - -#include <asm/rtc.h> - -static DECLARE_WAIT_QUEUE_HEAD(rtc_wait); -static struct fasync_struct *rtc_async_queue; - -/* - * rtc_lock protects rtc_irq_data - */ -static DEFINE_SPINLOCK(rtc_lock); -static unsigned long rtc_irq_data; - -/* - * rtc_sem protects rtc_inuse and rtc_ops - */ -static DEFINE_MUTEX(rtc_mutex); -static unsigned long rtc_inuse; -static struct rtc_ops *rtc_ops; - -#define rtc_epoch 1900UL - -/* - * Calculate the next alarm time given the requested alarm time mask - * and the current time. - */ -void rtc_next_alarm_time(struct rtc_time *next, struct rtc_time *now, struct rtc_time *alrm) -{ - unsigned long next_time; - unsigned long now_time; - - next->tm_year = now->tm_year; - next->tm_mon = now->tm_mon; - next->tm_mday = now->tm_mday; - next->tm_hour = alrm->tm_hour; - next->tm_min = alrm->tm_min; - next->tm_sec = alrm->tm_sec; - - rtc_tm_to_time(now, &now_time); - rtc_tm_to_time(next, &next_time); - - if (next_time < now_time) { - /* Advance one day */ - next_time += 60 * 60 * 24; - rtc_time_to_tm(next_time, next); - } -} -EXPORT_SYMBOL(rtc_next_alarm_time); - -static inline int rtc_arm_read_time(struct rtc_ops *ops, struct rtc_time *tm) -{ - memset(tm, 0, sizeof(struct rtc_time)); - return ops->read_time(tm); -} - -static inline int rtc_arm_set_time(struct rtc_ops *ops, struct rtc_time *tm) -{ - int ret; - - ret = rtc_valid_tm(tm); - if (ret == 0) - ret = ops->set_time(tm); - - return ret; -} - -static inline int rtc_arm_read_alarm(struct rtc_ops *ops, struct rtc_wkalrm *alrm) -{ - int ret = -EINVAL; - if (ops->read_alarm) { - memset(alrm, 0, sizeof(struct rtc_wkalrm)); - ret = ops->read_alarm(alrm); - } - return ret; -} - -static inline int rtc_arm_set_alarm(struct rtc_ops *ops, struct rtc_wkalrm *alrm) -{ - int ret = -EINVAL; - if (ops->set_alarm) - ret = ops->set_alarm(alrm); - return ret; -} - -void rtc_update(unsigned long num, unsigned long events) -{ - spin_lock(&rtc_lock); - rtc_irq_data = (rtc_irq_data + (num << 8)) | events; - spin_unlock(&rtc_lock); - - wake_up_interruptible(&rtc_wait); - kill_fasync(&rtc_async_queue, SIGIO, POLL_IN); -} -EXPORT_SYMBOL(rtc_update); - - -static ssize_t -rtc_read(struct file *file, char __user *buf, size_t count, loff_t *ppos) -{ - DECLARE_WAITQUEUE(wait, current); - unsigned long data; - ssize_t ret; - - if (count < sizeof(unsigned long)) - return -EINVAL; - - add_wait_queue(&rtc_wait, &wait); - do { - __set_current_state(TASK_INTERRUPTIBLE); - - spin_lock_irq(&rtc_lock); - data = rtc_irq_data; - rtc_irq_data = 0; - spin_unlock_irq(&rtc_lock); - - if (data != 0) { - ret = 0; - break; - } - if (file->f_flags & O_NONBLOCK) { - ret = -EAGAIN; - break; - } - if (signal_pending(current)) { - ret = -ERESTARTSYS; - break; - } - schedule(); - } while (1); - set_current_state(TASK_RUNNING); - remove_wait_queue(&rtc_wait, &wait); - - if (ret == 0) { - ret = put_user(data, (unsigned long __user *)buf); - if (ret == 0) - ret = sizeof(unsigned long); - } - return ret; -} - -static unsigned int rtc_poll(struct file *file, poll_table *wait) -{ - unsigned long data; - - poll_wait(file, &rtc_wait, wait); - - spin_lock_irq(&rtc_lock); - data = rtc_irq_data; - spin_unlock_irq(&rtc_lock); - - return data != 0 ? POLLIN | POLLRDNORM : 0; -} - -static int rtc_ioctl(struct inode *inode, struct file *file, unsigned int cmd, - unsigned long arg) -{ - struct rtc_ops *ops = file->private_data; - struct rtc_time tm; - struct rtc_wkalrm alrm; - void __user *uarg = (void __user *)arg; - int ret = -EINVAL; - - switch (cmd) { - case RTC_ALM_READ: - ret = rtc_arm_read_alarm(ops, &alrm); - if (ret) - break; - ret = copy_to_user(uarg, &alrm.time, sizeof(tm)); - if (ret) - ret = -EFAULT; - break; - - case RTC_ALM_SET: - ret = copy_from_user(&alrm.time, uarg, sizeof(tm)); - if (ret) { - ret = -EFAULT; - break; - } - alrm.enabled = 0; - alrm.pending = 0; - alrm.time.tm_mday = -1; - alrm.time.tm_mon = -1; - alrm.time.tm_year = -1; - alrm.time.tm_wday = -1; - alrm.time.tm_yday = -1; - alrm.time.tm_isdst = -1; - ret = rtc_arm_set_alarm(ops, &alrm); - break; - - case RTC_RD_TIME: - ret = rtc_arm_read_time(ops, &tm); - if (ret) - break; - ret = copy_to_user(uarg, &tm, sizeof(tm)); - if (ret) - ret = -EFAULT; - break; - - case RTC_SET_TIME: - if (!capable(CAP_SYS_TIME)) { - ret = -EACCES; - break; - } - ret = copy_from_user(&tm, uarg, sizeof(tm)); - if (ret) { - ret = -EFAULT; - break; - } - ret = rtc_arm_set_time(ops, &tm); - break; - - case RTC_EPOCH_SET: -#ifndef rtc_epoch - /* - * There were no RTC clocks before 1900. - */ - if (arg < 1900) { - ret = -EINVAL; - break; - } - if (!capable(CAP_SYS_TIME)) { - ret = -EACCES; - break; - } - rtc_epoch = arg; - ret = 0; -#endif - break; - - case RTC_EPOCH_READ: - ret = put_user(rtc_epoch, (unsigned long __user *)uarg); - break; - - case RTC_WKALM_SET: - ret = copy_from_user(&alrm, uarg, sizeof(alrm)); - if (ret) { - ret = -EFAULT; - break; - } - ret = rtc_arm_set_alarm(ops, &alrm); - break; - - case RTC_WKALM_RD: - ret = rtc_arm_read_alarm(ops, &alrm); - if (ret) - break; - ret = copy_to_user(uarg, &alrm, sizeof(alrm)); - if (ret) - ret = -EFAULT; - break; - - default: - if (ops->ioctl) - ret = ops->ioctl(cmd, arg); - break; - } - return ret; -} - -static int rtc_open(struct inode *inode, struct file *file) -{ - int ret; - - mutex_lock(&rtc_mutex); - - if (rtc_inuse) { - ret = -EBUSY; - } else if (!rtc_ops || !try_module_get(rtc_ops->owner)) { - ret = -ENODEV; - } else { - file->private_data = rtc_ops; - - ret = rtc_ops->open ? rtc_ops->open() : 0; - if (ret == 0) { - spin_lock_irq(&rtc_lock); - rtc_irq_data = 0; - spin_unlock_irq(&rtc_lock); - - rtc_inuse = 1; - } - } - mutex_unlock(&rtc_mutex); - - return ret; -} - -static int rtc_release(struct inode *inode, struct file *file) -{ - struct rtc_ops *ops = file->private_data; - - if (ops->release) - ops->release(); - - spin_lock_irq(&rtc_lock); - rtc_irq_data = 0; - spin_unlock_irq(&rtc_lock); - - module_put(rtc_ops->owner); - rtc_inuse = 0; - - return 0; -} - -static int rtc_fasync(int fd, struct file *file, int on) -{ - return fasync_helper(fd, file, on, &rtc_async_queue); -} - -static const struct file_operations rtc_fops = { - .owner = THIS_MODULE, - .llseek = no_llseek, - .read = rtc_read, - .poll = rtc_poll, - .ioctl = rtc_ioctl, - .open = rtc_open, - .release = rtc_release, - .fasync = rtc_fasync, -}; - -static struct miscdevice rtc_miscdev = { - .minor = RTC_MINOR, - .name = "rtc", - .fops = &rtc_fops, -}; - - -static int rtc_read_proc(char *page, char **start, off_t off, int count, int *eof, void *data) -{ - struct rtc_ops *ops = data; - struct rtc_wkalrm alrm; - struct rtc_time tm; - char *p = page; - - if (rtc_arm_read_time(ops, &tm) == 0) { - p += sprintf(p, - "rtc_time\t: %02d:%02d:%02d\n" - "rtc_date\t: %04d-%02d-%02d\n" - "rtc_epoch\t: %04lu\n", - tm.tm_hour, tm.tm_min, tm.tm_sec, - tm.tm_year + 1900, tm.tm_mon + 1, tm.tm_mday, - rtc_epoch); - } - - if (rtc_arm_read_alarm(ops, &alrm) == 0) { - p += sprintf(p, "alrm_time\t: "); - if ((unsigned int)alrm.time.tm_hour <= 24) - p += sprintf(p, "%02d:", alrm.time.tm_hour); - else - p += sprintf(p, "**:"); - if ((unsigned int)alrm.time.tm_min <= 59) - p += sprintf(p, "%02d:", alrm.time.tm_min); - else - p += sprintf(p, "**:"); - if ((unsigned int)alrm.time.tm_sec <= 59) - p += sprintf(p, "%02d\n", alrm.time.tm_sec); - else - p += sprintf(p, "**\n"); - - p += sprintf(p, "alrm_date\t: "); - if ((unsigned int)alrm.time.tm_year <= 200) - p += sprintf(p, "%04d-", alrm.time.tm_year + 1900); - else - p += sprintf(p, "****-"); - if ((unsigned int)alrm.time.tm_mon <= 11) - p += sprintf(p, "%02d-", alrm.time.tm_mon + 1); - else - p += sprintf(p, "**-"); - if ((unsigned int)alrm.time.tm_mday <= 31) - p += sprintf(p, "%02d\n", alrm.time.tm_mday); - else - p += sprintf(p, "**\n"); - p += sprintf(p, "alrm_wakeup\t: %s\n", - alrm.enabled ? "yes" : "no"); - p += sprintf(p, "alrm_pending\t: %s\n", - alrm.pending ? "yes" : "no"); - } - - if (ops->proc) - p += ops->proc(p); - - return p - page; -} - -int register_rtc(struct rtc_ops *ops) -{ - int ret = -EBUSY; - - mutex_lock(&rtc_mutex); - if (rtc_ops == NULL) { - rtc_ops = ops; - - ret = misc_register(&rtc_miscdev); - if (ret == 0) - create_proc_read_entry("driver/rtc", 0, NULL, - rtc_read_proc, ops); - } - mutex_unlock(&rtc_mutex); - - return ret; -} -EXPORT_SYMBOL(register_rtc); - -void unregister_rtc(struct rtc_ops *rtc) -{ - mutex_lock(&rtc_mutex); - if (rtc == rtc_ops) { - remove_proc_entry("driver/rtc", NULL); - misc_deregister(&rtc_miscdev); - rtc_ops = NULL; - } - mutex_unlock(&rtc_mutex); -} -EXPORT_SYMBOL(unregister_rtc); diff --git a/arch/arm/configs/at91cap9adk_defconfig b/arch/arm/configs/at91cap9adk_defconfig index e32e7364812..be2b2f38fd9 100644 --- a/arch/arm/configs/at91cap9adk_defconfig +++ b/arch/arm/configs/at91cap9adk_defconfig @@ -213,7 +213,6 @@ CONFIG_CPU_CP15_MMU=y # # CONFIG_TICK_ONESHOT is not set # CONFIG_PREEMPT is not set -# CONFIG_NO_IDLE_HZ is not set CONFIG_HZ=100 CONFIG_AEABI=y CONFIG_OABI_COMPAT=y @@ -907,7 +906,32 @@ CONFIG_USB_MON=y # # USB Gadget Support # -# CONFIG_USB_GADGET is not set +CONFIG_USB_GADGET=y +# CONFIG_USB_GADGET_DEBUG is not set +# CONFIG_USB_GADGET_DEBUG_FILES is not set +CONFIG_USB_GADGET_SELECTED=y +# CONFIG_USB_GADGET_AMD5536UDC is not set +CONFIG_USB_GADGET_ATMEL_USBA=y +CONFIG_USB_ATMEL_USBA=y +# CONFIG_USB_GADGET_FSL_USB2 is not set +# CONFIG_USB_GADGET_NET2280 is not set +# CONFIG_USB_GADGET_PXA2XX is not set +# CONFIG_USB_GADGET_M66592 is not set +# CONFIG_USB_GADGET_GOKU is not set +# CONFIG_USB_GADGET_LH7A40X is not set +# CONFIG_USB_GADGET_OMAP is not set +# CONFIG_USB_GADGET_S3C2410 is not set +# CONFIG_USB_GADGET_AT91 is not set +# CONFIG_USB_GADGET_DUMMY_HCD is not set +CONFIG_USB_GADGET_DUALSPEED=y +# CONFIG_USB_ZERO is not set +CONFIG_USB_ETH=m +CONFIG_USB_ETH_RNDIS=y +# CONFIG_USB_GADGETFS is not set +CONFIG_USB_FILE_STORAGE=m +# CONFIG_USB_FILE_STORAGE_TEST is not set +# CONFIG_USB_G_SERIAL is not set +# CONFIG_USB_MIDI_GADGET is not set CONFIG_MMC=y # CONFIG_MMC_DEBUG is not set # CONFIG_MMC_UNSAFE_RESUME is not set @@ -926,7 +950,59 @@ CONFIG_MMC_AT91=y # CONFIG_MMC_SPI is not set # CONFIG_NEW_LEDS is not set CONFIG_RTC_LIB=y -# CONFIG_RTC_CLASS is not set +CONFIG_RTC_CLASS=y +CONFIG_RTC_HCTOSYS=y +CONFIG_RTC_HCTOSYS_DEVICE="rtc0" +# CONFIG_RTC_DEBUG is not set + +# +# RTC interfaces +# +CONFIG_RTC_INTF_SYSFS=y +CONFIG_RTC_INTF_PROC=y +CONFIG_RTC_INTF_DEV=y +# CONFIG_RTC_INTF_DEV_UIE_EMUL is not set +# CONFIG_RTC_DRV_TEST is not set + +# +# I2C RTC drivers +# +# CONFIG_RTC_DRV_DS1307 is not set +# CONFIG_RTC_DRV_DS1374 is not set +# CONFIG_RTC_DRV_DS1672 is not set +# CONFIG_RTC_DRV_MAX6900 is not set +# CONFIG_RTC_DRV_RS5C372 is not set +# CONFIG_RTC_DRV_ISL1208 is not set +# CONFIG_RTC_DRV_X1205 is not set +# CONFIG_RTC_DRV_PCF8563 is not set +# CONFIG_RTC_DRV_PCF8583 is not set +# CONFIG_RTC_DRV_M41T80 is not set + +# +# SPI RTC drivers +# +# CONFIG_RTC_DRV_MAX6902 is not set +# CONFIG_RTC_DRV_R9701 is not set +# CONFIG_RTC_DRV_RS5C348 is not set + +# +# Platform RTC drivers +# +# CONFIG_RTC_DRV_CMOS is not set +# CONFIG_RTC_DRV_DS1511 is not set +# CONFIG_RTC_DRV_DS1553 is not set +# CONFIG_RTC_DRV_DS1742 is not set +# CONFIG_RTC_DRV_STK17TA8 is not set +# CONFIG_RTC_DRV_M48T86 is not set +# CONFIG_RTC_DRV_M48T59 is not set +# CONFIG_RTC_DRV_V3020 is not set + +# +# on-CPU RTC drivers +# +CONFIG_RTC_DRV_AT91SAM9=y +CONFIG_RTC_DRV_AT91SAM9_RTT=0 +CONFIG_RTC_DRV_AT91SAM9_GPBR=0 # # File systems diff --git a/arch/arm/configs/at91rm9200dk_defconfig b/arch/arm/configs/at91rm9200dk_defconfig index 2dbbbc3d4ac..868fb7b9530 100644 --- a/arch/arm/configs/at91rm9200dk_defconfig +++ b/arch/arm/configs/at91rm9200dk_defconfig @@ -169,7 +169,6 @@ CONFIG_AT91_CF=y # Kernel Features # # CONFIG_PREEMPT is not set -# CONFIG_NO_IDLE_HZ is not set # CONFIG_ARCH_DISCONTIGMEM_ENABLE is not set CONFIG_SELECT_MEMORY_MODEL=y CONFIG_FLATMEM_MANUAL=y diff --git a/arch/arm/configs/at91rm9200ek_defconfig b/arch/arm/configs/at91rm9200ek_defconfig index 6e994f7820c..de43fc67561 100644 --- a/arch/arm/configs/at91rm9200ek_defconfig +++ b/arch/arm/configs/at91rm9200ek_defconfig @@ -160,7 +160,6 @@ CONFIG_ISA_DMA_API=y # Kernel Features # # CONFIG_PREEMPT is not set -# CONFIG_NO_IDLE_HZ is not set # CONFIG_ARCH_DISCONTIGMEM_ENABLE is not set CONFIG_SELECT_MEMORY_MODEL=y CONFIG_FLATMEM_MANUAL=y diff --git a/arch/arm/configs/at91sam9260ek_defconfig b/arch/arm/configs/at91sam9260ek_defconfig index f659c938473..2011adfa675 100644 --- a/arch/arm/configs/at91sam9260ek_defconfig +++ b/arch/arm/configs/at91sam9260ek_defconfig @@ -220,7 +220,6 @@ CONFIG_CPU_CP15_MMU=y # # CONFIG_TICK_ONESHOT is not set # CONFIG_PREEMPT is not set -# CONFIG_NO_IDLE_HZ is not set CONFIG_HZ=100 # CONFIG_AEABI is not set # CONFIG_ARCH_DISCONTIGMEM_ENABLE is not set diff --git a/arch/arm/configs/at91sam9261ek_defconfig b/arch/arm/configs/at91sam9261ek_defconfig index 3802e85f748..4049768962d 100644 --- a/arch/arm/configs/at91sam9261ek_defconfig +++ b/arch/arm/configs/at91sam9261ek_defconfig @@ -213,7 +213,6 @@ CONFIG_CPU_CP15_MMU=y # # CONFIG_TICK_ONESHOT is not set # CONFIG_PREEMPT is not set -# CONFIG_NO_IDLE_HZ is not set CONFIG_HZ=100 # CONFIG_AEABI is not set # CONFIG_ARCH_DISCONTIGMEM_ENABLE is not set diff --git a/arch/arm/configs/at91sam9263ek_defconfig b/arch/arm/configs/at91sam9263ek_defconfig index 32a0d74e0c8..fa1c5aecb5a 100644 --- a/arch/arm/configs/at91sam9263ek_defconfig +++ b/arch/arm/configs/at91sam9263ek_defconfig @@ -213,7 +213,6 @@ CONFIG_CPU_CP15_MMU=y # # CONFIG_TICK_ONESHOT is not set # CONFIG_PREEMPT is not set -# CONFIG_NO_IDLE_HZ is not set CONFIG_HZ=100 # CONFIG_AEABI is not set # CONFIG_ARCH_DISCONTIGMEM_ENABLE is not set diff --git a/arch/arm/configs/at91sam9g20ek_defconfig b/arch/arm/configs/at91sam9g20ek_defconfig new file mode 100644 index 00000000000..c0686384736 --- /dev/null +++ b/arch/arm/configs/at91sam9g20ek_defconfig @@ -0,0 +1,1168 @@ +# +# Automatically generated make config: don't edit +# Linux kernel version: 2.6.24 +# Tue Jun 10 15:51:52 2008 +# +CONFIG_ARM=y +CONFIG_SYS_SUPPORTS_APM_EMULATION=y +CONFIG_GENERIC_GPIO=y +CONFIG_GENERIC_TIME=y +CONFIG_GENERIC_CLOCKEVENTS=y +CONFIG_MMU=y +# CONFIG_NO_IOPORT is not set +CONFIG_GENERIC_HARDIRQS=y +CONFIG_STACKTRACE_SUPPORT=y +CONFIG_LOCKDEP_SUPPORT=y +CONFIG_TRACE_IRQFLAGS_SUPPORT=y +CONFIG_HARDIRQS_SW_RESEND=y +CONFIG_GENERIC_IRQ_PROBE=y +CONFIG_RWSEM_GENERIC_SPINLOCK=y +# CONFIG_ARCH_HAS_ILOG2_U32 is not set +# CONFIG_ARCH_HAS_ILOG2_U64 is not set +CONFIG_GENERIC_HWEIGHT=y +CONFIG_GENERIC_CALIBRATE_DELAY=y +CONFIG_ZONE_DMA=y +CONFIG_VECTORS_BASE=0xffff0000 +CONFIG_DEFCONFIG_LIST="/lib/modules/$UNAME_RELEASE/.config" + +# +# General setup +# +CONFIG_EXPERIMENTAL=y +CONFIG_BROKEN_ON_SMP=y +CONFIG_INIT_ENV_ARG_LIMIT=32 +CONFIG_LOCALVERSION="" +# CONFIG_LOCALVERSION_AUTO is not set +# CONFIG_SWAP is not set +CONFIG_SYSVIPC=y +CONFIG_SYSVIPC_SYSCTL=y +# CONFIG_POSIX_MQUEUE is not set +# CONFIG_BSD_PROCESS_ACCT is not set +# CONFIG_TASKSTATS is not set +# CONFIG_USER_NS is not set +# CONFIG_PID_NS is not set +# CONFIG_AUDIT is not set +# CONFIG_IKCONFIG is not set +CONFIG_LOG_BUF_SHIFT=14 +# CONFIG_CGROUPS is not set +# CONFIG_FAIR_GROUP_SCHED is not set +CONFIG_SYSFS_DEPRECATED=y +# CONFIG_RELAY is not set +CONFIG_BLK_DEV_INITRD=y +CONFIG_INITRAMFS_SOURCE="" +CONFIG_CC_OPTIMIZE_FOR_SIZE=y +CONFIG_SYSCTL=y +# CONFIG_EMBEDDED is not set +CONFIG_UID16=y +CONFIG_SYSCTL_SYSCALL=y +CONFIG_KALLSYMS=y +# CONFIG_KALLSYMS_EXTRA_PASS is not set +CONFIG_HOTPLUG=y +CONFIG_PRINTK=y +CONFIG_BUG=y +CONFIG_ELF_CORE=y +CONFIG_BASE_FULL=y +CONFIG_FUTEX=y +CONFIG_ANON_INODES=y +CONFIG_EPOLL=y +CONFIG_SIGNALFD=y +CONFIG_EVENTFD=y +CONFIG_SHMEM=y +CONFIG_VM_EVENT_COUNTERS=y +CONFIG_SLAB=y +# CONFIG_SLUB is not set +# CONFIG_SLOB is not set +CONFIG_SLABINFO=y +CONFIG_RT_MUTEXES=y +# CONFIG_TINY_SHMEM is not set +CONFIG_BASE_SMALL=0 +CONFIG_MODULES=y +CONFIG_MODULE_UNLOAD=y +# CONFIG_MODULE_FORCE_UNLOAD is not set +# CONFIG_MODVERSIONS is not set +# CONFIG_MODULE_SRCVERSION_ALL is not set +CONFIG_KMOD=y +CONFIG_BLOCK=y +# CONFIG_LBD is not set +# CONFIG_BLK_DEV_IO_TRACE is not set +# CONFIG_LSF is not set +# CONFIG_BLK_DEV_BSG is not set + +# +# IO Schedulers +# +CONFIG_IOSCHED_NOOP=y +CONFIG_IOSCHED_AS=y +# CONFIG_IOSCHED_DEADLINE is not set +# CONFIG_IOSCHED_CFQ is not set +CONFIG_DEFAULT_AS=y +# CONFIG_DEFAULT_DEADLINE is not set +# CONFIG_DEFAULT_CFQ is not set +# CONFIG_DEFAULT_NOOP is not set +CONFIG_DEFAULT_IOSCHED="anticipatory" + +# +# System Type +# +# CONFIG_ARCH_AAEC2000 is not set +# CONFIG_ARCH_INTEGRATOR is not set +# CONFIG_ARCH_REALVIEW is not set +# CONFIG_ARCH_VERSATILE is not set +CONFIG_ARCH_AT91=y +# CONFIG_ARCH_CLPS7500 is not set +# CONFIG_ARCH_CLPS711X is not set +# CONFIG_ARCH_CO285 is not set +# CONFIG_ARCH_EBSA110 is not set +# CONFIG_ARCH_EP93XX is not set +# CONFIG_ARCH_FOOTBRIDGE is not set +# CONFIG_ARCH_NETX is not set +# CONFIG_ARCH_H720X is not set +# CONFIG_ARCH_IMX is not set +# CONFIG_ARCH_IOP13XX is not set +# CONFIG_ARCH_IOP32X is not set +# CONFIG_ARCH_IOP33X is not set +# CONFIG_ARCH_IXP23XX is not set +# CONFIG_ARCH_IXP2000 is not set +# CONFIG_ARCH_IXP4XX is not set +# CONFIG_ARCH_L7200 is not set +# CONFIG_ARCH_KS8695 is not set +# CONFIG_ARCH_NS9XXX is not set +# CONFIG_ARCH_MXC is not set +# CONFIG_ARCH_PNX4008 is not set +# CONFIG_ARCH_PXA is not set +# CONFIG_ARCH_RPC is not set +# CONFIG_ARCH_SA1100 is not set +# CONFIG_ARCH_S3C2410 is not set +# CONFIG_ARCH_SHARK is not set +# CONFIG_ARCH_LH7A40X is not set +# CONFIG_ARCH_DAVINCI is not set +# CONFIG_ARCH_OMAP is not set + +# +# Boot options +# + +# +# Power management +# + +# +# Atmel AT91 System-on-Chip +# +# CONFIG_ARCH_AT91RM9200 is not set +# CONFIG_ARCH_AT91SAM9260 is not set +# CONFIG_ARCH_AT91SAM9261 is not set +# CONFIG_ARCH_AT91SAM9263 is not set +# CONFIG_ARCH_AT91SAM9RL is not set +CONFIG_ARCH_AT91SAM9G20=y +# CONFIG_ARCH_AT91CAP9 is not set +# CONFIG_ARCH_AT91X40 is not set +CONFIG_AT91_PMC_UNIT=y + +# +# AT91SAM9G20 Board Type +# +CONFIG_MACH_AT91SAM9G20EK=y + +# +# AT91 Board Options +# +# CONFIG_MTD_AT91_DATAFLASH_CARD is not set +# CONFIG_MTD_NAND_AT91_BUSWIDTH_16 is not set + +# +# AT91 Feature Selections +# +CONFIG_AT91_PROGRAMMABLE_CLOCKS=y +# CONFIG_AT91_SLOW_CLOCK is not set +CONFIG_AT91_TIMER_HZ=100 +CONFIG_AT91_EARLY_DBGU=y +# CONFIG_AT91_EARLY_USART0 is not set +# CONFIG_AT91_EARLY_USART1 is not set +# CONFIG_AT91_EARLY_USART2 is not set +# CONFIG_AT91_EARLY_USART3 is not set +# CONFIG_AT91_EARLY_USART4 is not set +# CONFIG_AT91_EARLY_USART5 is not set + +# +# Processor Type +# +CONFIG_CPU_32=y +CONFIG_CPU_ARM926T=y +CONFIG_CPU_32v5=y +CONFIG_CPU_ABRT_EV5TJ=y +CONFIG_CPU_CACHE_VIVT=y +CONFIG_CPU_COPY_V4WB=y +CONFIG_CPU_TLB_V4WBI=y +CONFIG_CPU_CP15=y +CONFIG_CPU_CP15_MMU=y + +# +# Processor Features +# +# CONFIG_ARM_THUMB is not set +# CONFIG_CPU_ICACHE_DISABLE is not set +# CONFIG_CPU_DCACHE_DISABLE is not set +# CONFIG_CPU_DCACHE_WRITETHROUGH is not set +# CONFIG_CPU_CACHE_ROUND_ROBIN is not set +# CONFIG_OUTER_CACHE is not set + +# +# Bus support +# +# CONFIG_PCI_SYSCALL is not set +# CONFIG_ARCH_SUPPORTS_MSI is not set +# CONFIG_PCCARD is not set + +# +# Kernel Features +# +# CONFIG_TICK_ONESHOT is not set +# CONFIG_NO_HZ is not set +# CONFIG_HIGH_RES_TIMERS is not set +CONFIG_GENERIC_CLOCKEVENTS_BUILD=y +# CONFIG_PREEMPT is not set +CONFIG_HZ=100 +CONFIG_AEABI=y +CONFIG_OABI_COMPAT=y +# CONFIG_ARCH_DISCONTIGMEM_ENABLE is not set +CONFIG_SELECT_MEMORY_MODEL=y +CONFIG_FLATMEM_MANUAL=y +# CONFIG_DISCONTIGMEM_MANUAL is not set +# CONFIG_SPARSEMEM_MANUAL is not set +CONFIG_FLATMEM=y +CONFIG_FLAT_NODE_MEM_MAP=y +# CONFIG_SPARSEMEM_STATIC is not set +# CONFIG_SPARSEMEM_VMEMMAP_ENABLE is not set +CONFIG_SPLIT_PTLOCK_CPUS=4096 +# CONFIG_RESOURCES_64BIT is not set +CONFIG_ZONE_DMA_FLAG=1 +CONFIG_BOUNCE=y +CONFIG_VIRT_TO_BUS=y +CONFIG_LEDS=y +CONFIG_LEDS_CPU=y +CONFIG_ALIGNMENT_TRAP=y + +# +# Boot options +# +CONFIG_ZBOOT_ROM_TEXT=0x0 +CONFIG_ZBOOT_ROM_BSS=0x0 +CONFIG_CMDLINE="mem=64M console=ttyS0,115200 initrd=0x21100000,3145728 root=/dev/ram0 rw" +# CONFIG_XIP_KERNEL is not set +# CONFIG_KEXEC is not set + +# +# Floating point emulation +# + +# +# At least one emulation must be selected +# +CONFIG_FPE_NWFPE=y +# CONFIG_FPE_NWFPE_XP is not set +# CONFIG_FPE_FASTFPE is not set +# CONFIG_VFP is not set + +# +# Userspace binary formats +# +CONFIG_BINFMT_ELF=y +# CONFIG_BINFMT_AOUT is not set +# CONFIG_BINFMT_MISC is not set + +# +# Power management options +# +CONFIG_PM=y +# CONFIG_PM_LEGACY is not set +# CONFIG_PM_DEBUG is not set +CONFIG_PM_SLEEP=y +CONFIG_SUSPEND_UP_POSSIBLE=y +CONFIG_SUSPEND=y +# CONFIG_APM_EMULATION is not set + +# +# Networking +# +CONFIG_NET=y + +# +# Networking options +# +CONFIG_PACKET=y +# CONFIG_PACKET_MMAP is not set +CONFIG_UNIX=y +# CONFIG_NET_KEY is not set +CONFIG_INET=y +# CONFIG_IP_MULTICAST is not set +# CONFIG_IP_ADVANCED_ROUTER is not set +CONFIG_IP_FIB_HASH=y +CONFIG_IP_PNP=y +# CONFIG_IP_PNP_DHCP is not set +CONFIG_IP_PNP_BOOTP=y +# CONFIG_IP_PNP_RARP is not set +# CONFIG_NET_IPIP is not set +# CONFIG_NET_IPGRE is not set +# CONFIG_ARPD is not set +# CONFIG_SYN_COOKIES is not set +# CONFIG_INET_AH is not set +# CONFIG_INET_ESP is not set +# CONFIG_INET_IPCOMP is not set +# CONFIG_INET_XFRM_TUNNEL is not set +# CONFIG_INET_TUNNEL is not set +# CONFIG_INET_XFRM_MODE_TRANSPORT is not set +# CONFIG_INET_XFRM_MODE_TUNNEL is not set +# CONFIG_INET_XFRM_MODE_BEET is not set +# CONFIG_INET_LRO is not set +CONFIG_INET_DIAG=y +CONFIG_INET_TCP_DIAG=y +# CONFIG_TCP_CONG_ADVANCED is not set +CONFIG_TCP_CONG_CUBIC=y +CONFIG_DEFAULT_TCP_CONG="cubic" +# CONFIG_TCP_MD5SIG is not set +# CONFIG_IPV6 is not set +# CONFIG_INET6_XFRM_TUNNEL is not set +# CONFIG_INET6_TUNNEL is not set +# CONFIG_NETWORK_SECMARK is not set +# CONFIG_NETFILTER is not set +# CONFIG_IP_DCCP is not set +# CONFIG_IP_SCTP is not set +# CONFIG_TIPC is not set +# CONFIG_ATM is not set +# CONFIG_BRIDGE is not set +# CONFIG_VLAN_8021Q is not set +# CONFIG_DECNET is not set +# CONFIG_LLC2 is not set +# CONFIG_IPX is not set +# CONFIG_ATALK is not set +# CONFIG_X25 is not set +# CONFIG_LAPB is not set +# CONFIG_ECONET is not set +# CONFIG_WAN_ROUTER is not set +# CONFIG_NET_SCHED is not set + +# +# Network testing +# +# CONFIG_NET_PKTGEN is not set +# CONFIG_HAMRADIO is not set +# CONFIG_IRDA is not set +# CONFIG_BT is not set +# CONFIG_AF_RXRPC is not set + +# +# Wireless +# +# CONFIG_CFG80211 is not set +# CONFIG_WIRELESS_EXT is not set +# CONFIG_MAC80211 is not set +# CONFIG_IEEE80211 is not set +# CONFIG_RFKILL is not set +# CONFIG_NET_9P is not set + +# +# Device Drivers +# + +# +# Generic Driver Options +# +CONFIG_UEVENT_HELPER_PATH="/sbin/hotplug" +CONFIG_STANDALONE=y +CONFIG_PREVENT_FIRMWARE_BUILD=y +# CONFIG_FW_LOADER is not set +# CONFIG_SYS_HYPERVISOR is not set +# CONFIG_CONNECTOR is not set +CONFIG_MTD=y +# CONFIG_MTD_DEBUG is not set +CONFIG_MTD_CONCAT=y +CONFIG_MTD_PARTITIONS=y +# CONFIG_MTD_REDBOOT_PARTS is not set +CONFIG_MTD_CMDLINE_PARTS=y +# CONFIG_MTD_AFS_PARTS is not set + +# +# User Modules And Translation Layers +# +CONFIG_MTD_CHAR=y +CONFIG_MTD_BLKDEVS=y +CONFIG_MTD_BLOCK=y +# CONFIG_FTL is not set +# CONFIG_NFTL is not set +# CONFIG_INFTL is not set +# CONFIG_RFD_FTL is not set +# CONFIG_SSFDC is not set +# CONFIG_MTD_OOPS is not set + +# +# RAM/ROM/Flash chip drivers +# +# CONFIG_MTD_CFI is not set +# CONFIG_MTD_JEDECPROBE is not set +CONFIG_MTD_MAP_BANK_WIDTH_1=y +CONFIG_MTD_MAP_BANK_WIDTH_2=y +CONFIG_MTD_MAP_BANK_WIDTH_4=y +# CONFIG_MTD_MAP_BANK_WIDTH_8 is not set +# CONFIG_MTD_MAP_BANK_WIDTH_16 is not set +# CONFIG_MTD_MAP_BANK_WIDTH_32 is not set +CONFIG_MTD_CFI_I1=y +CONFIG_MTD_CFI_I2=y +# CONFIG_MTD_CFI_I4 is not set +# CONFIG_MTD_CFI_I8 is not set +# CONFIG_MTD_RAM is not set +# CONFIG_MTD_ROM is not set +# CONFIG_MTD_ABSENT is not set + +# +# Mapping drivers for chip access +# +# CONFIG_MTD_COMPLEX_MAPPINGS is not set +# CONFIG_MTD_PLATRAM is not set + +# +# Self-contained MTD device drivers +# +CONFIG_MTD_DATAFLASH=y +# CONFIG_MTD_M25P80 is not set +# CONFIG_MTD_SLRAM is not set +# CONFIG_MTD_PHRAM is not set +# CONFIG_MTD_MTDRAM is not set +# CONFIG_MTD_BLOCK2MTD is not set + +# +# Disk-On-Chip Device Drivers +# +# CONFIG_MTD_DOC2000 is not set +# CONFIG_MTD_DOC2001 is not set +# CONFIG_MTD_DOC2001PLUS is not set +CONFIG_MTD_NAND=y +# CONFIG_MTD_NAND_VERIFY_WRITE is not set +# CONFIG_MTD_NAND_ECC_SMC is not set +# CONFIG_MTD_NAND_MUSEUM_IDS is not set +CONFIG_MTD_NAND_IDS=y +# CONFIG_MTD_NAND_DISKONCHIP is not set +CONFIG_MTD_NAND_AT91=y +CONFIG_MTD_NAND_AT91_ECC_SOFT=y +# CONFIG_MTD_NAND_AT91_ECC_HW is not set +# CONFIG_MTD_NAND_AT91_ECC_NONE is not set +# CONFIG_MTD_NAND_NANDSIM is not set +# CONFIG_MTD_NAND_PLATFORM is not set +# CONFIG_MTD_ALAUDA is not set +# CONFIG_MTD_ONENAND is not set + +# +# UBI - Unsorted block images +# +# CONFIG_MTD_UBI is not set +# CONFIG_PARPORT is not set +CONFIG_BLK_DEV=y +# CONFIG_BLK_DEV_COW_COMMON is not set +CONFIG_BLK_DEV_LOOP=y +# CONFIG_BLK_DEV_CRYPTOLOOP is not set +# CONFIG_BLK_DEV_NBD is not set +# CONFIG_BLK_DEV_UB is not set +CONFIG_BLK_DEV_RAM=y +CONFIG_BLK_DEV_RAM_COUNT=16 +CONFIG_BLK_DEV_RAM_SIZE=8192 +CONFIG_BLK_DEV_RAM_BLOCKSIZE=1024 +# CONFIG_CDROM_PKTCDVD is not set +# CONFIG_ATA_OVER_ETH is not set +CONFIG_MISC_DEVICES=y +CONFIG_ATMEL_PWM=y +# CONFIG_EEPROM_93CX6 is not set +CONFIG_ATMEL_SSC=y + +# +# SCSI device support +# +# CONFIG_RAID_ATTRS is not set +CONFIG_SCSI=y +CONFIG_SCSI_DMA=y +# CONFIG_SCSI_TGT is not set +# CONFIG_SCSI_NETLINK is not set +CONFIG_SCSI_PROC_FS=y + +# +# SCSI support type (disk, tape, CD-ROM) +# +CONFIG_BLK_DEV_SD=y +# CONFIG_CHR_DEV_ST is not set +# CONFIG_CHR_DEV_OSST is not set +# CONFIG_BLK_DEV_SR is not set +# CONFIG_CHR_DEV_SG is not set +# CONFIG_CHR_DEV_SCH is not set + +# +# Some SCSI devices (e.g. CD jukebox) support multiple LUNs +# +CONFIG_SCSI_MULTI_LUN=y +# CONFIG_SCSI_CONSTANTS is not set +# CONFIG_SCSI_LOGGING is not set +# CONFIG_SCSI_SCAN_ASYNC is not set +CONFIG_SCSI_WAIT_SCAN=m + +# +# SCSI Transports +# +# CONFIG_SCSI_SPI_ATTRS is not set +# CONFIG_SCSI_FC_ATTRS is not set +# CONFIG_SCSI_ISCSI_ATTRS is not set +# CONFIG_SCSI_SAS_LIBSAS is not set +# CONFIG_SCSI_SRP_ATTRS is not set +# CONFIG_SCSI_LOWLEVEL is not set +# CONFIG_ATA is not set +# CONFIG_MD is not set +CONFIG_NETDEVICES=y +# CONFIG_NETDEVICES_MULTIQUEUE is not set +# CONFIG_DUMMY is not set +# CONFIG_BONDING is not set +# CONFIG_MACVLAN is not set +# CONFIG_EQUALIZER is not set +# CONFIG_TUN is not set +# CONFIG_VETH is not set +CONFIG_PHYLIB=y + +# +# MII PHY device drivers +# +# CONFIG_MARVELL_PHY is not set +# CONFIG_DAVICOM_PHY is not set +# CONFIG_QSEMI_PHY is not set +# CONFIG_LXT_PHY is not set +# CONFIG_CICADA_PHY is not set +# CONFIG_VITESSE_PHY is not set +# CONFIG_SMSC_PHY is not set +# CONFIG_BROADCOM_PHY is not set +# CONFIG_ICPLUS_PHY is not set +# CONFIG_FIXED_PHY is not set +# CONFIG_MDIO_BITBANG is not set +CONFIG_NET_ETHERNET=y +CONFIG_MII=y +CONFIG_MACB=y +# CONFIG_AX88796 is not set +# CONFIG_SMC91X is not set +# CONFIG_DM9000 is not set +# CONFIG_IBM_NEW_EMAC_ZMII is not set +# CONFIG_IBM_NEW_EMAC_RGMII is not set +# CONFIG_IBM_NEW_EMAC_TAH is not set +# CONFIG_IBM_NEW_EMAC_EMAC4 is not set +# CONFIG_B44 is not set +# CONFIG_NETDEV_1000 is not set +# CONFIG_NETDEV_10000 is not set + +# +# Wireless LAN +# +# CONFIG_WLAN_PRE80211 is not set +# CONFIG_WLAN_80211 is not set + +# +# USB Network Adapters +# +# CONFIG_USB_CATC is not set +# CONFIG_USB_KAWETH is not set +# CONFIG_USB_PEGASUS is not set +# CONFIG_USB_RTL8150 is not set +# CONFIG_USB_USBNET is not set +# CONFIG_WAN is not set +# CONFIG_PPP is not set +# CONFIG_SLIP is not set +# CONFIG_SHAPER is not set +# CONFIG_NETCONSOLE is not set +# CONFIG_NETPOLL is not set +# CONFIG_NET_POLL_CONTROLLER is not set +# CONFIG_ISDN is not set + +# +# Input device support +# +CONFIG_INPUT=y +# CONFIG_INPUT_FF_MEMLESS is not set +# CONFIG_INPUT_POLLDEV is not set + +# +# Userland interfaces +# +CONFIG_INPUT_MOUSEDEV=y +# CONFIG_INPUT_MOUSEDEV_PSAUX is not set +CONFIG_INPUT_MOUSEDEV_SCREEN_X=320 +CONFIG_INPUT_MOUSEDEV_SCREEN_Y=240 +# CONFIG_INPUT_JOYDEV is not set +CONFIG_INPUT_EVDEV=y +# CONFIG_INPUT_EVBUG is not set + +# +# Input Device Drivers +# +CONFIG_INPUT_KEYBOARD=y +# CONFIG_KEYBOARD_ATKBD is not set +# CONFIG_KEYBOARD_SUNKBD is not set +# CONFIG_KEYBOARD_LKKBD is not set +# CONFIG_KEYBOARD_XTKBD is not set +# CONFIG_KEYBOARD_NEWTON is not set +# CONFIG_KEYBOARD_STOWAWAY is not set +CONFIG_KEYBOARD_GPIO=y +# CONFIG_INPUT_MOUSE is not set +# CONFIG_INPUT_JOYSTICK is not set +# CONFIG_INPUT_TABLET is not set +# CONFIG_INPUT_TOUCHSCREEN is not set +# CONFIG_INPUT_MISC is not set + +# +# Hardware I/O ports +# +CONFIG_SERIO=y +CONFIG_SERIO_SERPORT=y +# CONFIG_SERIO_RAW is not set +# CONFIG_GAMEPORT is not set + +# +# Character devices +# +CONFIG_VT=y +CONFIG_VT_CONSOLE=y +CONFIG_HW_CONSOLE=y +# CONFIG_VT_HW_CONSOLE_BINDING is not set +# CONFIG_SERIAL_NONSTANDARD is not set + +# +# Serial drivers +# +# CONFIG_SERIAL_8250 is not set + +# +# Non-8250 serial port support +# +CONFIG_SERIAL_ATMEL=y +CONFIG_SERIAL_ATMEL_CONSOLE=y +# CONFIG_SERIAL_ATMEL_TTYAT is not set +CONFIG_SERIAL_CORE=y +CONFIG_SERIAL_CORE_CONSOLE=y +CONFIG_UNIX98_PTYS=y +CONFIG_LEGACY_PTYS=y +CONFIG_LEGACY_PTY_COUNT=16 +# CONFIG_IPMI_HANDLER is not set +CONFIG_HW_RANDOM=y +# CONFIG_NVRAM is not set +# CONFIG_R3964 is not set +# CONFIG_RAW_DRIVER is not set +# CONFIG_TCG_TPM is not set +# CONFIG_I2C is not set + +# +# SPI support +# +CONFIG_SPI=y +CONFIG_SPI_MASTER=y + +# +# SPI Master Controller Drivers +# +CONFIG_SPI_ATMEL=y +# CONFIG_SPI_BITBANG is not set + +# +# SPI Protocol Masters +# +# CONFIG_SPI_AT25 is not set +CONFIG_SPI_SPIDEV=y +# CONFIG_SPI_TLE62X0 is not set +# CONFIG_W1 is not set +# CONFIG_POWER_SUPPLY is not set +# CONFIG_HWMON is not set +# CONFIG_WATCHDOG is not set + +# +# Sonics Silicon Backplane +# +CONFIG_SSB_POSSIBLE=y +# CONFIG_SSB is not set + +# +# Multifunction device drivers +# +# CONFIG_MFD_SM501 is not set + +# +# Multimedia devices +# +# CONFIG_VIDEO_DEV is not set +# CONFIG_DVB_CORE is not set +# CONFIG_DAB is not set + +# +# Graphics support +# +# CONFIG_VGASTATE is not set +# CONFIG_VIDEO_OUTPUT_CONTROL is not set +# CONFIG_FB is not set +# CONFIG_BACKLIGHT_LCD_SUPPORT is not set + +# +# Display device support +# +# CONFIG_DISPLAY_SUPPORT is not set + +# +# Console display driver support +# +# CONFIG_VGA_CONSOLE is not set +CONFIG_DUMMY_CONSOLE=y + +# +# Sound +# +CONFIG_SOUND=y + +# +# Advanced Linux Sound Architecture +# +CONFIG_SND=y +CONFIG_SND_TIMER=y +CONFIG_SND_PCM=y +CONFIG_SND_SEQUENCER=y +# CONFIG_SND_SEQ_DUMMY is not set +CONFIG_SND_OSSEMUL=y +CONFIG_SND_MIXER_OSS=y +CONFIG_SND_PCM_OSS=y +CONFIG_SND_PCM_OSS_PLUGINS=y +CONFIG_SND_SEQUENCER_OSS=y +# CONFIG_SND_DYNAMIC_MINORS is not set +CONFIG_SND_SUPPORT_OLD_API=y +# CONFIG_SND_VERBOSE_PROCFS is not set +# CONFIG_SND_VERBOSE_PRINTK is not set +# CONFIG_SND_DEBUG is not set + +# +# Generic devices +# +# CONFIG_SND_DUMMY is not set +# CONFIG_SND_VIRMIDI is not set +# CONFIG_SND_MTPAV is not set +# CONFIG_SND_SERIAL_U16550 is not set +# CONFIG_SND_MPU401 is not set + +# +# ALSA ARM devices +# +# CONFIG_SND_AT91_AC97 is not set + +# +# SPI devices +# +CONFIG_SND_AT73C213=y +CONFIG_SND_AT73C213_TARGET_BITRATE=48000 + +# +# USB devices +# +# CONFIG_SND_USB_AUDIO is not set +# CONFIG_SND_USB_CAIAQ is not set + +# +# System on Chip audio support +# +# CONFIG_SND_SOC is not set + +# +# SoC Audio support for SuperH +# + +# +# Open Sound System +# +# CONFIG_SOUND_PRIME is not set +CONFIG_HID_SUPPORT=y +CONFIG_HID=y +# CONFIG_HID_DEBUG is not set +# CONFIG_HIDRAW is not set + +# +# USB Input Devices +# +CONFIG_USB_HID=y +# CONFIG_USB_HIDINPUT_POWERBOOK is not set +# CONFIG_HID_FF is not set +# CONFIG_USB_HIDDEV is not set +CONFIG_USB_SUPPORT=y +CONFIG_USB_ARCH_HAS_HCD=y +CONFIG_USB_ARCH_HAS_OHCI=y +# CONFIG_USB_ARCH_HAS_EHCI is not set +CONFIG_USB=y +# CONFIG_USB_DEBUG is not set + +# +# Miscellaneous USB options +# +CONFIG_USB_DEVICEFS=y +# CONFIG_USB_DEVICE_CLASS is not set +# CONFIG_USB_DYNAMIC_MINORS is not set +# CONFIG_USB_SUSPEND is not set +# CONFIG_USB_PERSIST is not set +# CONFIG_USB_OTG is not set + +# +# USB Host Controller Drivers +# +# CONFIG_USB_ISP116X_HCD is not set +CONFIG_USB_OHCI_HCD=y +# CONFIG_USB_OHCI_BIG_ENDIAN_DESC is not set +# CONFIG_USB_OHCI_BIG_ENDIAN_MMIO is not set +CONFIG_USB_OHCI_LITTLE_ENDIAN=y +# CONFIG_USB_SL811_HCD is not set +# CONFIG_USB_R8A66597_HCD is not set + +# +# USB Device Class drivers +# +# CONFIG_USB_ACM is not set +# CONFIG_USB_PRINTER is not set + +# +# NOTE: USB_STORAGE enables SCSI, and 'SCSI disk support' +# + +# +# may also be needed; see USB_STORAGE Help for more information +# +CONFIG_USB_STORAGE=y +# CONFIG_USB_STORAGE_DEBUG is not set +# CONFIG_USB_STORAGE_DATAFAB is not set +# CONFIG_USB_STORAGE_FREECOM is not set +# CONFIG_USB_STORAGE_ISD200 is not set +# CONFIG_USB_STORAGE_DPCM is not set +# CONFIG_USB_STORAGE_USBAT is not set +# CONFIG_USB_STORAGE_SDDR09 is not set +# CONFIG_USB_STORAGE_SDDR55 is not set +# CONFIG_USB_STORAGE_JUMPSHOT is not set +# CONFIG_USB_STORAGE_ALAUDA is not set +# CONFIG_USB_STORAGE_KARMA is not set +# CONFIG_USB_LIBUSUAL is not set + +# +# USB Imaging devices +# +# CONFIG_USB_MDC800 is not set +# CONFIG_USB_MICROTEK is not set +CONFIG_USB_MON=y + +# +# USB port drivers +# + +# +# USB Serial Converter support +# +# CONFIG_USB_SERIAL is not set + +# +# USB Miscellaneous drivers +# +# CONFIG_USB_EMI62 is not set +# CONFIG_USB_EMI26 is not set +# CONFIG_USB_ADUTUX is not set +# CONFIG_USB_AUERSWALD is not set +# CONFIG_USB_RIO500 is not set +# CONFIG_USB_LEGOTOWER is not set +# CONFIG_USB_LCD is not set +# CONFIG_USB_BERRY_CHARGE is not set +# CONFIG_USB_LED is not set +# CONFIG_USB_CYPRESS_CY7C63 is not set +# CONFIG_USB_CYTHERM is not set +# CONFIG_USB_PHIDGET is not set +# CONFIG_USB_IDMOUSE is not set +# CONFIG_USB_FTDI_ELAN is not set +# CONFIG_USB_APPLEDISPLAY is not set +# CONFIG_USB_LD is not set +# CONFIG_USB_TRANCEVIBRATOR is not set +# CONFIG_USB_IOWARRIOR is not set +# CONFIG_USB_TEST is not set + +# +# USB DSL modem support +# + +# +# USB Gadget Support +# +CONFIG_USB_GADGET=y +# CONFIG_USB_GADGET_DEBUG_FILES is not set +CONFIG_USB_GADGET_SELECTED=y +# CONFIG_USB_GADGET_AMD5536UDC is not set +# CONFIG_USB_GADGET_ATMEL_USBA is not set +# CONFIG_USB_GADGET_FSL_USB2 is not set +# CONFIG_USB_GADGET_NET2280 is not set +# CONFIG_USB_GADGET_PXA2XX is not set +# CONFIG_USB_GADGET_M66592 is not set +# CONFIG_USB_GADGET_GOKU is not set +# CONFIG_USB_GADGET_LH7A40X is not set +# CONFIG_USB_GADGET_OMAP is not set +# CONFIG_USB_GADGET_S3C2410 is not set +CONFIG_USB_GADGET_AT91=y +CONFIG_USB_AT91=y +# CONFIG_USB_GADGET_DUMMY_HCD is not set +# CONFIG_USB_GADGET_DUALSPEED is not set +CONFIG_USB_ZERO=m +# CONFIG_USB_ETH is not set +CONFIG_USB_GADGETFS=m +CONFIG_USB_FILE_STORAGE=m +# CONFIG_USB_FILE_STORAGE_TEST is not set +CONFIG_USB_G_SERIAL=m +# CONFIG_USB_MIDI_GADGET is not set +CONFIG_MMC=y +# CONFIG_MMC_DEBUG is not set +# CONFIG_MMC_UNSAFE_RESUME is not set + +# +# MMC/SD Card Drivers +# +CONFIG_MMC_BLOCK=y +CONFIG_MMC_BLOCK_BOUNCE=y +# CONFIG_SDIO_UART is not set + +# +# MMC/SD Host Controller Drivers +# +CONFIG_MMC_AT91=y +# CONFIG_MMC_SPI is not set +CONFIG_NEW_LEDS=y +CONFIG_LEDS_CLASS=y + +# +# LED drivers +# +CONFIG_LEDS_ATMEL_PWM=y +CONFIG_LEDS_GPIO=y + +# +# LED Triggers +# +CONFIG_LEDS_TRIGGERS=y +CONFIG_LEDS_TRIGGER_TIMER=y +CONFIG_LEDS_TRIGGER_HEARTBEAT=y +CONFIG_RTC_LIB=y +CONFIG_RTC_CLASS=y +CONFIG_RTC_HCTOSYS=y +CONFIG_RTC_HCTOSYS_DEVICE="rtc0" +# CONFIG_RTC_DEBUG is not set + +# +# RTC interfaces +# +CONFIG_RTC_INTF_SYSFS=y +CONFIG_RTC_INTF_PROC=y +CONFIG_RTC_INTF_DEV=y +# CONFIG_RTC_INTF_DEV_UIE_EMUL is not set +# CONFIG_RTC_DRV_TEST is not set + +# +# SPI RTC drivers +# +# CONFIG_RTC_DRV_RS5C348 is not set +# CONFIG_RTC_DRV_MAX6902 is not set + +# +# Platform RTC drivers +# +# CONFIG_RTC_DRV_CMOS is not set +# CONFIG_RTC_DRV_DS1553 is not set +# CONFIG_RTC_DRV_STK17TA8 is not set +# CONFIG_RTC_DRV_DS1742 is not set +# CONFIG_RTC_DRV_M48T86 is not set +# CONFIG_RTC_DRV_M48T59 is not set +# CONFIG_RTC_DRV_V3020 is not set + +# +# on-CPU RTC drivers +# +CONFIG_RTC_DRV_AT91SAM9=y +CONFIG_RTC_DRV_AT91SAM9_RTT=0 +CONFIG_RTC_DRV_AT91SAM9_GPBR=0 + +# +# File systems +# +CONFIG_EXT2_FS=y +# CONFIG_EXT2_FS_XATTR is not set +# CONFIG_EXT2_FS_XIP is not set +# CONFIG_EXT3_FS is not set +# CONFIG_EXT4DEV_FS is not set +# CONFIG_REISERFS_FS is not set +# CONFIG_JFS_FS is not set +# CONFIG_FS_POSIX_ACL is not set +# CONFIG_XFS_FS is not set +# CONFIG_GFS2_FS is not set +# CONFIG_OCFS2_FS is not set +# CONFIG_MINIX_FS is not set +# CONFIG_ROMFS_FS is not set +CONFIG_INOTIFY=y +CONFIG_INOTIFY_USER=y +# CONFIG_QUOTA is not set +CONFIG_DNOTIFY=y +# CONFIG_AUTOFS_FS is not set +# CONFIG_AUTOFS4_FS is not set +# CONFIG_FUSE_FS is not set + +# +# CD-ROM/DVD Filesystems +# +# CONFIG_ISO9660_FS is not set +# CONFIG_UDF_FS is not set + +# +# DOS/FAT/NT Filesystems +# +CONFIG_FAT_FS=y +CONFIG_MSDOS_FS=y +CONFIG_VFAT_FS=y +CONFIG_FAT_DEFAULT_CODEPAGE=437 +CONFIG_FAT_DEFAULT_IOCHARSET="iso8859-1" +# CONFIG_NTFS_FS is not set + +# +# Pseudo filesystems +# +CONFIG_PROC_FS=y +CONFIG_PROC_SYSCTL=y +CONFIG_SYSFS=y +CONFIG_TMPFS=y +# CONFIG_TMPFS_POSIX_ACL is not set +# CONFIG_HUGETLB_PAGE is not set +# CONFIG_CONFIGFS_FS is not set + +# +# Miscellaneous filesystems +# +# CONFIG_ADFS_FS is not set +# CONFIG_AFFS_FS is not set +# CONFIG_HFS_FS is not set +# CONFIG_HFSPLUS_FS is not set +# CONFIG_BEFS_FS is not set +# CONFIG_BFS_FS is not set +# CONFIG_EFS_FS is not set +CONFIG_JFFS2_FS=y +CONFIG_JFFS2_FS_DEBUG=0 +CONFIG_JFFS2_FS_WRITEBUFFER=y +# CONFIG_JFFS2_FS_WBUF_VERIFY is not set +CONFIG_JFFS2_SUMMARY=y +# CONFIG_JFFS2_FS_XATTR is not set +# CONFIG_JFFS2_COMPRESSION_OPTIONS is not set +CONFIG_JFFS2_ZLIB=y +# CONFIG_JFFS2_LZO is not set +CONFIG_JFFS2_RTIME=y +# CONFIG_JFFS2_RUBIN is not set +CONFIG_CRAMFS=y +# CONFIG_VXFS_FS is not set +# CONFIG_HPFS_FS is not set +# CONFIG_QNX4FS_FS is not set +# CONFIG_SYSV_FS is not set +# CONFIG_UFS_FS is not set +CONFIG_NETWORK_FILESYSTEMS=y +CONFIG_NFS_FS=y +CONFIG_NFS_V3=y +# CONFIG_NFS_V3_ACL is not set +# CONFIG_NFS_V4 is not set +# CONFIG_NFS_DIRECTIO is not set +# CONFIG_NFSD is not set +CONFIG_ROOT_NFS=y +CONFIG_LOCKD=y +CONFIG_LOCKD_V4=y +CONFIG_NFS_COMMON=y +CONFIG_SUNRPC=y +# CONFIG_SUNRPC_BIND34 is not set +# CONFIG_RPCSEC_GSS_KRB5 is not set +# CONFIG_RPCSEC_GSS_SPKM3 is not set +# CONFIG_SMB_FS is not set +# CONFIG_CIFS is not set +# CONFIG_NCP_FS is not set +# CONFIG_CODA_FS is not set +# CONFIG_AFS_FS is not set + +# +# Partition Types +# +# CONFIG_PARTITION_ADVANCED is not set +CONFIG_MSDOS_PARTITION=y +CONFIG_NLS=y +CONFIG_NLS_DEFAULT="iso8859-1" +CONFIG_NLS_CODEPAGE_437=y +# CONFIG_NLS_CODEPAGE_737 is not set +# CONFIG_NLS_CODEPAGE_775 is not set +CONFIG_NLS_CODEPAGE_850=y +# CONFIG_NLS_CODEPAGE_852 is not set +# CONFIG_NLS_CODEPAGE_855 is not set +# CONFIG_NLS_CODEPAGE_857 is not set +# CONFIG_NLS_CODEPAGE_860 is not set +# CONFIG_NLS_CODEPAGE_861 is not set +# CONFIG_NLS_CODEPAGE_862 is not set +# CONFIG_NLS_CODEPAGE_863 is not set +# CONFIG_NLS_CODEPAGE_864 is not set +# CONFIG_NLS_CODEPAGE_865 is not set +# CONFIG_NLS_CODEPAGE_866 is not set +# CONFIG_NLS_CODEPAGE_869 is not set +# CONFIG_NLS_CODEPAGE_936 is not set +# CONFIG_NLS_CODEPAGE_950 is not set +# CONFIG_NLS_CODEPAGE_932 is not set +# CONFIG_NLS_CODEPAGE_949 is not set +# CONFIG_NLS_CODEPAGE_874 is not set +# CONFIG_NLS_ISO8859_8 is not set +# CONFIG_NLS_CODEPAGE_1250 is not set +# CONFIG_NLS_CODEPAGE_1251 is not set +# CONFIG_NLS_ASCII is not set +CONFIG_NLS_ISO8859_1=y +# CONFIG_NLS_ISO8859_2 is not set +# CONFIG_NLS_ISO8859_3 is not set +# CONFIG_NLS_ISO8859_4 is not set +# CONFIG_NLS_ISO8859_5 is not set +# CONFIG_NLS_ISO8859_6 is not set +# CONFIG_NLS_ISO8859_7 is not set +# CONFIG_NLS_ISO8859_9 is not set +# CONFIG_NLS_ISO8859_13 is not set +# CONFIG_NLS_ISO8859_14 is not set +CONFIG_NLS_ISO8859_15=y +# CONFIG_NLS_KOI8_R is not set +# CONFIG_NLS_KOI8_U is not set +CONFIG_NLS_UTF8=y +# CONFIG_DLM is not set +# CONFIG_INSTRUMENTATION is not set + +# +# Kernel hacking +# +# CONFIG_PRINTK_TIME is not set +# CONFIG_ENABLE_WARN_DEPRECATED is not set +CONFIG_ENABLE_MUST_CHECK=y +# CONFIG_MAGIC_SYSRQ is not set +# CONFIG_UNUSED_SYMBOLS is not set +# CONFIG_DEBUG_FS is not set +# CONFIG_HEADERS_CHECK is not set +# CONFIG_DEBUG_KERNEL is not set +CONFIG_DEBUG_BUGVERBOSE=y +CONFIG_FRAME_POINTER=y +# CONFIG_SAMPLES is not set +# CONFIG_DEBUG_USER is not set + +# +# Security options +# +# CONFIG_KEYS is not set +# CONFIG_SECURITY is not set +# CONFIG_SECURITY_FILE_CAPABILITIES is not set +# CONFIG_CRYPTO is not set + +# +# Library routines +# +CONFIG_BITREVERSE=y +# CONFIG_CRC_CCITT is not set +# CONFIG_CRC16 is not set +# CONFIG_CRC_ITU_T is not set +CONFIG_CRC32=y +# CONFIG_CRC7 is not set +# CONFIG_LIBCRC32C is not set +CONFIG_ZLIB_INFLATE=y +CONFIG_ZLIB_DEFLATE=y +CONFIG_PLIST=y +CONFIG_HAS_IOMEM=y +CONFIG_HAS_IOPORT=y diff --git a/arch/arm/configs/at91sam9rlek_defconfig b/arch/arm/configs/at91sam9rlek_defconfig index 98e6746d02b..d8ec5f9ca6e 100644 --- a/arch/arm/configs/at91sam9rlek_defconfig +++ b/arch/arm/configs/at91sam9rlek_defconfig @@ -211,7 +211,6 @@ CONFIG_CPU_CP15_MMU=y # # CONFIG_TICK_ONESHOT is not set # CONFIG_PREEMPT is not set -# CONFIG_NO_IDLE_HZ is not set CONFIG_HZ=100 # CONFIG_AEABI is not set # CONFIG_ARCH_DISCONTIGMEM_ENABLE is not set diff --git a/arch/arm/configs/ateb9200_defconfig b/arch/arm/configs/ateb9200_defconfig index d846a492e5c..85c80f723d8 100644 --- a/arch/arm/configs/ateb9200_defconfig +++ b/arch/arm/configs/ateb9200_defconfig @@ -171,7 +171,6 @@ CONFIG_AT91_CF=m # Kernel Features # CONFIG_PREEMPT=y -CONFIG_NO_IDLE_HZ=y CONFIG_HZ=100 # CONFIG_AEABI is not set # CONFIG_ARCH_DISCONTIGMEM_ENABLE is not set diff --git a/arch/arm/configs/cm_x270_defconfig b/arch/arm/configs/cm_x270_defconfig index 5cab08397ae..33b201c3b30 100644 --- a/arch/arm/configs/cm_x270_defconfig +++ b/arch/arm/configs/cm_x270_defconfig @@ -194,7 +194,6 @@ CONFIG_PCI_HOST_ITE8152=y # # CONFIG_TICK_ONESHOT is not set # CONFIG_PREEMPT is not set -# CONFIG_NO_IDLE_HZ is not set CONFIG_HZ=100 # CONFIG_AEABI is not set # CONFIG_ARCH_DISCONTIGMEM_ENABLE is not set diff --git a/arch/arm/configs/collie_defconfig b/arch/arm/configs/collie_defconfig index 4264e273202..f7622e65816 100644 --- a/arch/arm/configs/collie_defconfig +++ b/arch/arm/configs/collie_defconfig @@ -166,7 +166,6 @@ CONFIG_PCMCIA_SA1100=y # Kernel Features # # CONFIG_PREEMPT is not set -# CONFIG_NO_IDLE_HZ is not set CONFIG_HZ=100 # CONFIG_AEABI is not set CONFIG_ARCH_DISCONTIGMEM_ENABLE=y diff --git a/arch/arm/configs/corgi_defconfig b/arch/arm/configs/corgi_defconfig index e8980a9bb89..9b8748a8d9d 100644 --- a/arch/arm/configs/corgi_defconfig +++ b/arch/arm/configs/corgi_defconfig @@ -165,7 +165,6 @@ CONFIG_PCMCIA_PXA2XX=y # Kernel Features # CONFIG_PREEMPT=y -# CONFIG_NO_IDLE_HZ is not set # CONFIG_ARCH_DISCONTIGMEM_ENABLE is not set CONFIG_SELECT_MEMORY_MODEL=y CONFIG_FLATMEM_MANUAL=y diff --git a/arch/arm/configs/ecbat91_defconfig b/arch/arm/configs/ecbat91_defconfig index 90ed214e367..cfeb817ad21 100644 --- a/arch/arm/configs/ecbat91_defconfig +++ b/arch/arm/configs/ecbat91_defconfig @@ -230,7 +230,6 @@ CONFIG_AT91_CF=y # # CONFIG_TICK_ONESHOT is not set CONFIG_PREEMPT=y -# CONFIG_NO_IDLE_HZ is not set CONFIG_HZ=100 # CONFIG_AEABI is not set # CONFIG_ARCH_DISCONTIGMEM_ENABLE is not set diff --git a/arch/arm/configs/em_x270_defconfig b/arch/arm/configs/em_x270_defconfig index 6bea0901bdf..d3114c23603 100644 --- a/arch/arm/configs/em_x270_defconfig +++ b/arch/arm/configs/em_x270_defconfig @@ -197,7 +197,6 @@ CONFIG_XSCALE_PMU=y # # CONFIG_TICK_ONESHOT is not set # CONFIG_PREEMPT is not set -# CONFIG_NO_IDLE_HZ is not set CONFIG_HZ=100 CONFIG_AEABI=y CONFIG_OABI_COMPAT=y diff --git a/arch/arm/configs/ep93xx_defconfig b/arch/arm/configs/ep93xx_defconfig index 24a701ab33e..21aa013793c 100644 --- a/arch/arm/configs/ep93xx_defconfig +++ b/arch/arm/configs/ep93xx_defconfig @@ -184,7 +184,6 @@ CONFIG_ARM_AMBA=y # Kernel Features # # CONFIG_PREEMPT is not set -# CONFIG_NO_IDLE_HZ is not set CONFIG_HZ=100 # CONFIG_AEABI is not set # CONFIG_ARCH_DISCONTIGMEM_ENABLE is not set diff --git a/arch/arm/configs/eseries_pxa_defconfig b/arch/arm/configs/eseries_pxa_defconfig index ed487b90dbe..493ecee24f9 100644 --- a/arch/arm/configs/eseries_pxa_defconfig +++ b/arch/arm/configs/eseries_pxa_defconfig @@ -251,7 +251,6 @@ CONFIG_PCMCIA_PXA2XX=m # Kernel Features # # CONFIG_PREEMPT is not set -# CONFIG_NO_IDLE_HZ is not set CONFIG_HZ=100 CONFIG_AEABI=y CONFIG_OABI_COMPAT=y diff --git a/arch/arm/configs/iop13xx_defconfig b/arch/arm/configs/iop13xx_defconfig index 988b4d13e76..482e5706105 100644 --- a/arch/arm/configs/iop13xx_defconfig +++ b/arch/arm/configs/iop13xx_defconfig @@ -197,7 +197,6 @@ CONFIG_PCI_LEGACY=y # # CONFIG_TICK_ONESHOT is not set # CONFIG_PREEMPT is not set -# CONFIG_NO_IDLE_HZ is not set CONFIG_HZ=100 # CONFIG_AEABI is not set # CONFIG_ARCH_DISCONTIGMEM_ENABLE is not set diff --git a/arch/arm/configs/iop32x_defconfig b/arch/arm/configs/iop32x_defconfig index 83f40d4041a..8612f58e105 100644 --- a/arch/arm/configs/iop32x_defconfig +++ b/arch/arm/configs/iop32x_defconfig @@ -201,7 +201,6 @@ CONFIG_PCI_LEGACY=y # # CONFIG_TICK_ONESHOT is not set # CONFIG_PREEMPT is not set -# CONFIG_NO_IDLE_HZ is not set CONFIG_HZ=100 # CONFIG_AEABI is not set # CONFIG_ARCH_DISCONTIGMEM_ENABLE is not set diff --git a/arch/arm/configs/iop33x_defconfig b/arch/arm/configs/iop33x_defconfig index 917afb5ccfa..8b0098d19d0 100644 --- a/arch/arm/configs/iop33x_defconfig +++ b/arch/arm/configs/iop33x_defconfig @@ -197,7 +197,6 @@ CONFIG_PCI_LEGACY=y # # CONFIG_TICK_ONESHOT is not set # CONFIG_PREEMPT is not set -# CONFIG_NO_IDLE_HZ is not set CONFIG_HZ=100 # CONFIG_AEABI is not set # CONFIG_ARCH_DISCONTIGMEM_ENABLE is not set diff --git a/arch/arm/configs/ixp2000_defconfig b/arch/arm/configs/ixp2000_defconfig index f8f9793b526..84680db6c61 100644 --- a/arch/arm/configs/ixp2000_defconfig +++ b/arch/arm/configs/ixp2000_defconfig @@ -184,7 +184,6 @@ CONFIG_PCI=y # Kernel Features # # CONFIG_PREEMPT is not set -# CONFIG_NO_IDLE_HZ is not set CONFIG_HZ=100 # CONFIG_AEABI is not set # CONFIG_ARCH_DISCONTIGMEM_ENABLE is not set diff --git a/arch/arm/configs/ixp23xx_defconfig b/arch/arm/configs/ixp23xx_defconfig index 27cf022dd80..4a2f7b2372d 100644 --- a/arch/arm/configs/ixp23xx_defconfig +++ b/arch/arm/configs/ixp23xx_defconfig @@ -180,7 +180,6 @@ CONFIG_PCI=y # Kernel Features # # CONFIG_PREEMPT is not set -# CONFIG_NO_IDLE_HZ is not set CONFIG_HZ=100 # CONFIG_AEABI is not set # CONFIG_ARCH_DISCONTIGMEM_ENABLE is not set diff --git a/arch/arm/configs/ixp4xx_defconfig b/arch/arm/configs/ixp4xx_defconfig index efa0485d2f7..fc14932e3ab 100644 --- a/arch/arm/configs/ixp4xx_defconfig +++ b/arch/arm/configs/ixp4xx_defconfig @@ -165,6 +165,7 @@ CONFIG_ARCH_PRPMC1100=y CONFIG_MACH_NAS100D=y CONFIG_MACH_DSMG600=y CONFIG_ARCH_IXDP4XX=y +CONFIG_MACH_FSG=y CONFIG_CPU_IXP46X=y CONFIG_CPU_IXP43X=y CONFIG_MACH_GTWX5715=y @@ -770,7 +771,7 @@ CONFIG_ATA=y # CONFIG_SATA_SIL24 is not set # CONFIG_SATA_SIS is not set # CONFIG_SATA_ULI is not set -# CONFIG_SATA_VIA is not set +CONFIG_SATA_VIA=y # CONFIG_SATA_VITESSE is not set # CONFIG_SATA_INIC162X is not set # CONFIG_PATA_ALI is not set @@ -1143,7 +1144,7 @@ CONFIG_HWMON=y # CONFIG_SENSORS_VIA686A is not set # CONFIG_SENSORS_VT1211 is not set # CONFIG_SENSORS_VT8231 is not set -# CONFIG_SENSORS_W83781D is not set +CONFIG_SENSORS_W83781D=y # CONFIG_SENSORS_W83791D is not set # CONFIG_SENSORS_W83792D is not set # CONFIG_SENSORS_W83793 is not set @@ -1334,8 +1335,8 @@ CONFIG_LEDS_CLASS=y # # LED drivers # -# CONFIG_LEDS_IXP4XX is not set CONFIG_LEDS_GPIO=y +CONFIG_LEDS_FSG=y # # LED Triggers @@ -1367,7 +1368,7 @@ CONFIG_RTC_INTF_DEV=y # CONFIG_RTC_DRV_DS1672 is not set # CONFIG_RTC_DRV_MAX6900 is not set # CONFIG_RTC_DRV_RS5C372 is not set -# CONFIG_RTC_DRV_ISL1208 is not set +CONFIG_RTC_DRV_ISL1208=y CONFIG_RTC_DRV_X1205=y CONFIG_RTC_DRV_PCF8563=y # CONFIG_RTC_DRV_PCF8583 is not set diff --git a/arch/arm/configs/kafa_defconfig b/arch/arm/configs/kafa_defconfig index ae51a40db6f..6dd95a2c8d5 100644 --- a/arch/arm/configs/kafa_defconfig +++ b/arch/arm/configs/kafa_defconfig @@ -162,7 +162,6 @@ CONFIG_CPU_TLB_V4WBI=y # Kernel Features # CONFIG_PREEMPT=y -# CONFIG_NO_IDLE_HZ is not set CONFIG_HZ=100 # CONFIG_AEABI is not set # CONFIG_ARCH_DISCONTIGMEM_ENABLE is not set diff --git a/arch/arm/configs/kb9202_defconfig b/arch/arm/configs/kb9202_defconfig index c16537d9d67..8e74c66f239 100644 --- a/arch/arm/configs/kb9202_defconfig +++ b/arch/arm/configs/kb9202_defconfig @@ -126,7 +126,6 @@ CONFIG_ISA_DMA_API=y # # Kernel Features # -# CONFIG_NO_IDLE_HZ is not set # CONFIG_ARCH_DISCONTIGMEM_ENABLE is not set CONFIG_FLATMEM=y CONFIG_FLAT_NODE_MEM_MAP=y diff --git a/arch/arm/configs/kirkwood_defconfig b/arch/arm/configs/kirkwood_defconfig new file mode 100644 index 00000000000..e3357ba10f1 --- /dev/null +++ b/arch/arm/configs/kirkwood_defconfig @@ -0,0 +1,1426 @@ +# +# Automatically generated make config: don't edit +# Linux kernel version: 2.6.26-rc5 +# Sun Jun 22 15:51:25 2008 +# +CONFIG_ARM=y +CONFIG_SYS_SUPPORTS_APM_EMULATION=y +CONFIG_GENERIC_GPIO=y +CONFIG_GENERIC_TIME=y +CONFIG_GENERIC_CLOCKEVENTS=y +CONFIG_MMU=y +# CONFIG_NO_IOPORT is not set +CONFIG_GENERIC_HARDIRQS=y +CONFIG_STACKTRACE_SUPPORT=y +CONFIG_HAVE_LATENCYTOP_SUPPORT=y +CONFIG_LOCKDEP_SUPPORT=y +CONFIG_TRACE_IRQFLAGS_SUPPORT=y +CONFIG_HARDIRQS_SW_RESEND=y +CONFIG_GENERIC_IRQ_PROBE=y +CONFIG_RWSEM_GENERIC_SPINLOCK=y +# CONFIG_ARCH_HAS_ILOG2_U32 is not set +# CONFIG_ARCH_HAS_ILOG2_U64 is not set +CONFIG_GENERIC_HWEIGHT=y +CONFIG_GENERIC_CALIBRATE_DELAY=y +CONFIG_ARCH_SUPPORTS_AOUT=y +CONFIG_ZONE_DMA=y +CONFIG_VECTORS_BASE=0xffff0000 +CONFIG_DEFCONFIG_LIST="/lib/modules/$UNAME_RELEASE/.config" + +# +# General setup +# +CONFIG_EXPERIMENTAL=y +CONFIG_BROKEN_ON_SMP=y +CONFIG_LOCK_KERNEL=y +CONFIG_INIT_ENV_ARG_LIMIT=32 +CONFIG_LOCALVERSION="" +CONFIG_LOCALVERSION_AUTO=y +CONFIG_SWAP=y +CONFIG_SYSVIPC=y +CONFIG_SYSVIPC_SYSCTL=y +# CONFIG_POSIX_MQUEUE is not set +# CONFIG_BSD_PROCESS_ACCT is not set +# CONFIG_TASKSTATS is not set +# CONFIG_AUDIT is not set +# CONFIG_IKCONFIG is not set +CONFIG_LOG_BUF_SHIFT=14 +# CONFIG_CGROUPS is not set +# CONFIG_GROUP_SCHED is not set +# CONFIG_SYSFS_DEPRECATED_V2 is not set +# CONFIG_RELAY is not set +# CONFIG_NAMESPACES is not set +# CONFIG_BLK_DEV_INITRD is not set +CONFIG_CC_OPTIMIZE_FOR_SIZE=y +CONFIG_SYSCTL=y +CONFIG_EMBEDDED=y +CONFIG_UID16=y +CONFIG_SYSCTL_SYSCALL=y +CONFIG_SYSCTL_SYSCALL_CHECK=y +CONFIG_KALLSYMS=y +# CONFIG_KALLSYMS_ALL is not set +# CONFIG_KALLSYMS_EXTRA_PASS is not set +CONFIG_HOTPLUG=y +CONFIG_PRINTK=y +CONFIG_BUG=y +CONFIG_ELF_CORE=y +CONFIG_COMPAT_BRK=y +CONFIG_BASE_FULL=y +CONFIG_FUTEX=y +CONFIG_ANON_INODES=y +CONFIG_EPOLL=y +CONFIG_SIGNALFD=y +CONFIG_TIMERFD=y +CONFIG_EVENTFD=y +CONFIG_SHMEM=y +CONFIG_VM_EVENT_COUNTERS=y +CONFIG_SLAB=y +# CONFIG_SLUB is not set +# CONFIG_SLOB is not set +CONFIG_PROFILING=y +# CONFIG_MARKERS is not set +CONFIG_OPROFILE=y +CONFIG_HAVE_OPROFILE=y +CONFIG_KPROBES=y +CONFIG_KRETPROBES=y +CONFIG_HAVE_KPROBES=y +CONFIG_HAVE_KRETPROBES=y +# CONFIG_HAVE_DMA_ATTRS is not set +CONFIG_PROC_PAGE_MONITOR=y +CONFIG_SLABINFO=y +CONFIG_RT_MUTEXES=y +# CONFIG_TINY_SHMEM is not set +CONFIG_BASE_SMALL=0 +CONFIG_MODULES=y +# CONFIG_MODULE_FORCE_LOAD is not set +CONFIG_MODULE_UNLOAD=y +# CONFIG_MODULE_FORCE_UNLOAD is not set +# CONFIG_MODVERSIONS is not set +# CONFIG_MODULE_SRCVERSION_ALL is not set +# CONFIG_KMOD is not set +CONFIG_BLOCK=y +# CONFIG_LBD is not set +# CONFIG_BLK_DEV_IO_TRACE is not set +# CONFIG_LSF is not set +# CONFIG_BLK_DEV_BSG is not set + +# +# IO Schedulers +# +CONFIG_IOSCHED_NOOP=y +CONFIG_IOSCHED_AS=y +CONFIG_IOSCHED_DEADLINE=y +CONFIG_IOSCHED_CFQ=y +# CONFIG_DEFAULT_AS is not set +# CONFIG_DEFAULT_DEADLINE is not set +CONFIG_DEFAULT_CFQ=y +# CONFIG_DEFAULT_NOOP is not set +CONFIG_DEFAULT_IOSCHED="cfq" +CONFIG_CLASSIC_RCU=y + +# +# System Type +# +# CONFIG_ARCH_AAEC2000 is not set +# CONFIG_ARCH_INTEGRATOR is not set +# CONFIG_ARCH_REALVIEW is not set +# CONFIG_ARCH_VERSATILE is not set +# CONFIG_ARCH_AT91 is not set +# CONFIG_ARCH_CLPS7500 is not set +# CONFIG_ARCH_CLPS711X is not set +# CONFIG_ARCH_CO285 is not set +# CONFIG_ARCH_EBSA110 is not set +# CONFIG_ARCH_EP93XX is not set +# CONFIG_ARCH_FOOTBRIDGE is not set +# CONFIG_ARCH_NETX is not set +# CONFIG_ARCH_H720X is not set +# CONFIG_ARCH_IMX is not set +# CONFIG_ARCH_IOP13XX is not set +# CONFIG_ARCH_IOP32X is not set +# CONFIG_ARCH_IOP33X is not set +# CONFIG_ARCH_IXP23XX is not set +# CONFIG_ARCH_IXP2000 is not set +# CONFIG_ARCH_IXP4XX is not set +# CONFIG_ARCH_L7200 is not set +CONFIG_ARCH_KIRKWOOD=y +# CONFIG_ARCH_KS8695 is not set +# CONFIG_ARCH_NS9XXX is not set +# CONFIG_ARCH_LOKI is not set +# CONFIG_ARCH_MV78XX0 is not set +# CONFIG_ARCH_MXC is not set +# CONFIG_ARCH_ORION5X is not set +# CONFIG_ARCH_PNX4008 is not set +# CONFIG_ARCH_PXA is not set +# CONFIG_ARCH_RPC is not set +# CONFIG_ARCH_SA1100 is not set +# CONFIG_ARCH_S3C2410 is not set +# CONFIG_ARCH_SHARK is not set +# CONFIG_ARCH_LH7A40X is not set +# CONFIG_ARCH_DAVINCI is not set +# CONFIG_ARCH_OMAP is not set +# CONFIG_ARCH_MSM7X00A is not set + +# +# Marvell Kirkwood Implementations +# +CONFIG_MACH_DB88F6281_BP=y +CONFIG_MACH_RD88F6192_NAS=y +CONFIG_MACH_RD88F6281=y + +# +# Boot options +# + +# +# Power management +# +CONFIG_PLAT_ORION=y + +# +# Processor Type +# +CONFIG_CPU_32=y +CONFIG_CPU_FEROCEON=y +# CONFIG_CPU_FEROCEON_OLD_ID is not set +CONFIG_CPU_32v5=y +CONFIG_CPU_ABRT_EV5T=y +CONFIG_CPU_PABRT_NOIFAR=y +CONFIG_CPU_CACHE_VIVT=y +CONFIG_CPU_COPY_FEROCEON=y +CONFIG_CPU_TLB_FEROCEON=y +CONFIG_CPU_CP15=y +CONFIG_CPU_CP15_MMU=y + +# +# Processor Features +# +CONFIG_ARM_THUMB=y +# CONFIG_CPU_ICACHE_DISABLE is not set +# CONFIG_CPU_DCACHE_DISABLE is not set +CONFIG_OUTER_CACHE=y +CONFIG_CACHE_FEROCEON_L2=y + +# +# Bus support +# +CONFIG_PCI=y +CONFIG_PCI_SYSCALL=y +# CONFIG_ARCH_SUPPORTS_MSI is not set +CONFIG_PCI_LEGACY=y +# CONFIG_PCI_DEBUG is not set +# CONFIG_PCCARD is not set + +# +# Kernel Features +# +CONFIG_TICK_ONESHOT=y +CONFIG_NO_HZ=y +CONFIG_HIGH_RES_TIMERS=y +CONFIG_GENERIC_CLOCKEVENTS_BUILD=y +CONFIG_PREEMPT=y +CONFIG_HZ=100 +CONFIG_AEABI=y +# CONFIG_OABI_COMPAT is not set +# CONFIG_ARCH_DISCONTIGMEM_ENABLE is not set +CONFIG_SELECT_MEMORY_MODEL=y +CONFIG_FLATMEM_MANUAL=y +# CONFIG_DISCONTIGMEM_MANUAL is not set +# CONFIG_SPARSEMEM_MANUAL is not set +CONFIG_FLATMEM=y +CONFIG_FLAT_NODE_MEM_MAP=y +# CONFIG_SPARSEMEM_STATIC is not set +# CONFIG_SPARSEMEM_VMEMMAP_ENABLE is not set +CONFIG_PAGEFLAGS_EXTENDED=y +CONFIG_SPLIT_PTLOCK_CPUS=4096 +# CONFIG_RESOURCES_64BIT is not set +CONFIG_ZONE_DMA_FLAG=1 +CONFIG_BOUNCE=y +CONFIG_VIRT_TO_BUS=y +CONFIG_ALIGNMENT_TRAP=y + +# +# Boot options +# +CONFIG_ZBOOT_ROM_TEXT=0x0 +CONFIG_ZBOOT_ROM_BSS=0x0 +CONFIG_CMDLINE="" +# CONFIG_XIP_KERNEL is not set +# CONFIG_KEXEC is not set + +# +# Floating point emulation +# + +# +# At least one emulation must be selected +# +# CONFIG_VFP is not set + +# +# Userspace binary formats +# +CONFIG_BINFMT_ELF=y +# CONFIG_BINFMT_AOUT is not set +# CONFIG_BINFMT_MISC is not set + +# +# Power management options +# +# CONFIG_PM is not set +CONFIG_ARCH_SUSPEND_POSSIBLE=y + +# +# Networking +# +CONFIG_NET=y + +# +# Networking options +# +CONFIG_PACKET=y +CONFIG_PACKET_MMAP=y +CONFIG_UNIX=y +CONFIG_XFRM=y +# CONFIG_XFRM_USER is not set +# CONFIG_XFRM_SUB_POLICY is not set +# CONFIG_XFRM_MIGRATE is not set +# CONFIG_XFRM_STATISTICS is not set +# CONFIG_NET_KEY is not set +CONFIG_INET=y +CONFIG_IP_MULTICAST=y +# CONFIG_IP_ADVANCED_ROUTER is not set +CONFIG_IP_FIB_HASH=y +CONFIG_IP_PNP=y +CONFIG_IP_PNP_DHCP=y +CONFIG_IP_PNP_BOOTP=y +# CONFIG_IP_PNP_RARP is not set +# CONFIG_NET_IPIP is not set +# CONFIG_NET_IPGRE is not set +# CONFIG_IP_MROUTE is not set +# CONFIG_ARPD is not set +# CONFIG_SYN_COOKIES is not set +# CONFIG_INET_AH is not set +# CONFIG_INET_ESP is not set +# CONFIG_INET_IPCOMP is not set +# CONFIG_INET_XFRM_TUNNEL is not set +# CONFIG_INET_TUNNEL is not set +CONFIG_INET_XFRM_MODE_TRANSPORT=y +CONFIG_INET_XFRM_MODE_TUNNEL=y +CONFIG_INET_XFRM_MODE_BEET=y +# CONFIG_INET_LRO is not set +CONFIG_INET_DIAG=y +CONFIG_INET_TCP_DIAG=y +# CONFIG_TCP_CONG_ADVANCED is not set +CONFIG_TCP_CONG_CUBIC=y +CONFIG_DEFAULT_TCP_CONG="cubic" +# CONFIG_TCP_MD5SIG is not set +# CONFIG_IPV6 is not set +# CONFIG_NETWORK_SECMARK is not set +# CONFIG_NETFILTER is not set +# CONFIG_IP_DCCP is not set +# CONFIG_IP_SCTP is not set +# CONFIG_TIPC is not set +# CONFIG_ATM is not set +# CONFIG_BRIDGE is not set +# CONFIG_VLAN_8021Q is not set +# CONFIG_DECNET is not set +# CONFIG_LLC2 is not set +# CONFIG_IPX is not set +# CONFIG_ATALK is not set +# CONFIG_X25 is not set +# CONFIG_LAPB is not set +# CONFIG_ECONET is not set +# CONFIG_WAN_ROUTER is not set +# CONFIG_NET_SCHED is not set + +# +# Network testing +# +CONFIG_NET_PKTGEN=m +# CONFIG_NET_TCPPROBE is not set +# CONFIG_HAMRADIO is not set +# CONFIG_CAN is not set +# CONFIG_IRDA is not set +# CONFIG_BT is not set +# CONFIG_AF_RXRPC is not set + +# +# Wireless +# +# CONFIG_CFG80211 is not set +CONFIG_WIRELESS_EXT=y +# CONFIG_MAC80211 is not set +# CONFIG_IEEE80211 is not set +# CONFIG_RFKILL is not set +# CONFIG_NET_9P is not set + +# +# Device Drivers +# + +# +# Generic Driver Options +# +CONFIG_UEVENT_HELPER_PATH="/sbin/hotplug" +CONFIG_STANDALONE=y +CONFIG_PREVENT_FIRMWARE_BUILD=y +CONFIG_FW_LOADER=y +# CONFIG_DEBUG_DRIVER is not set +# CONFIG_DEBUG_DEVRES is not set +# CONFIG_SYS_HYPERVISOR is not set +# CONFIG_CONNECTOR is not set +CONFIG_MTD=y +# CONFIG_MTD_DEBUG is not set +# CONFIG_MTD_CONCAT is not set +CONFIG_MTD_PARTITIONS=y +# CONFIG_MTD_REDBOOT_PARTS is not set +CONFIG_MTD_CMDLINE_PARTS=y +# CONFIG_MTD_AFS_PARTS is not set +# CONFIG_MTD_AR7_PARTS is not set + +# +# User Modules And Translation Layers +# +CONFIG_MTD_CHAR=y +CONFIG_MTD_BLKDEVS=y +CONFIG_MTD_BLOCK=y +# CONFIG_FTL is not set +# CONFIG_NFTL is not set +# CONFIG_INFTL is not set +# CONFIG_RFD_FTL is not set +# CONFIG_SSFDC is not set +# CONFIG_MTD_OOPS is not set + +# +# RAM/ROM/Flash chip drivers +# +CONFIG_MTD_CFI=y +CONFIG_MTD_JEDECPROBE=y +CONFIG_MTD_GEN_PROBE=y +CONFIG_MTD_CFI_ADV_OPTIONS=y +CONFIG_MTD_CFI_NOSWAP=y +# CONFIG_MTD_CFI_BE_BYTE_SWAP is not set +# CONFIG_MTD_CFI_LE_BYTE_SWAP is not set +CONFIG_MTD_CFI_GEOMETRY=y +CONFIG_MTD_MAP_BANK_WIDTH_1=y +CONFIG_MTD_MAP_BANK_WIDTH_2=y +# CONFIG_MTD_MAP_BANK_WIDTH_4 is not set +# CONFIG_MTD_MAP_BANK_WIDTH_8 is not set +# CONFIG_MTD_MAP_BANK_WIDTH_16 is not set +# CONFIG_MTD_MAP_BANK_WIDTH_32 is not set +CONFIG_MTD_CFI_I1=y +CONFIG_MTD_CFI_I2=y +# CONFIG_MTD_CFI_I4 is not set +# CONFIG_MTD_CFI_I8 is not set +# CONFIG_MTD_OTP is not set +CONFIG_MTD_CFI_INTELEXT=y +# CONFIG_MTD_CFI_AMDSTD is not set +CONFIG_MTD_CFI_STAA=y +CONFIG_MTD_CFI_UTIL=y +# CONFIG_MTD_RAM is not set +# CONFIG_MTD_ROM is not set +# CONFIG_MTD_ABSENT is not set + +# +# Mapping drivers for chip access +# +# CONFIG_MTD_COMPLEX_MAPPINGS is not set +CONFIG_MTD_PHYSMAP=y +CONFIG_MTD_PHYSMAP_START=0x0 +CONFIG_MTD_PHYSMAP_LEN=0x0 +CONFIG_MTD_PHYSMAP_BANKWIDTH=0 +# CONFIG_MTD_ARM_INTEGRATOR is not set +# CONFIG_MTD_IMPA7 is not set +# CONFIG_MTD_INTEL_VR_NOR is not set +# CONFIG_MTD_PLATRAM is not set + +# +# Self-contained MTD device drivers +# +# CONFIG_MTD_PMC551 is not set +# CONFIG_MTD_DATAFLASH is not set +CONFIG_MTD_M25P80=y +CONFIG_M25PXX_USE_FAST_READ=y +# CONFIG_MTD_SLRAM is not set +# CONFIG_MTD_PHRAM is not set +# CONFIG_MTD_MTDRAM is not set +# CONFIG_MTD_BLOCK2MTD is not set + +# +# Disk-On-Chip Device Drivers +# +# CONFIG_MTD_DOC2000 is not set +# CONFIG_MTD_DOC2001 is not set +# CONFIG_MTD_DOC2001PLUS is not set +CONFIG_MTD_NAND=y +CONFIG_MTD_NAND_VERIFY_WRITE=y +# CONFIG_MTD_NAND_ECC_SMC is not set +# CONFIG_MTD_NAND_MUSEUM_IDS is not set +CONFIG_MTD_NAND_IDS=y +# CONFIG_MTD_NAND_DISKONCHIP is not set +# CONFIG_MTD_NAND_CAFE is not set +# CONFIG_MTD_NAND_NANDSIM is not set +# CONFIG_MTD_NAND_PLATFORM is not set +# CONFIG_MTD_ALAUDA is not set +CONFIG_MTD_NAND_ORION=y +# CONFIG_MTD_ONENAND is not set + +# +# UBI - Unsorted block images +# +# CONFIG_MTD_UBI is not set +# CONFIG_PARPORT is not set +CONFIG_BLK_DEV=y +# CONFIG_BLK_CPQ_DA is not set +# CONFIG_BLK_CPQ_CISS_DA is not set +# CONFIG_BLK_DEV_DAC960 is not set +# CONFIG_BLK_DEV_UMEM is not set +# CONFIG_BLK_DEV_COW_COMMON is not set +CONFIG_BLK_DEV_LOOP=y +# CONFIG_BLK_DEV_CRYPTOLOOP is not set +# CONFIG_BLK_DEV_NBD is not set +# CONFIG_BLK_DEV_SX8 is not set +# CONFIG_BLK_DEV_UB is not set +# CONFIG_BLK_DEV_RAM is not set +# CONFIG_CDROM_PKTCDVD is not set +# CONFIG_ATA_OVER_ETH is not set +# CONFIG_MISC_DEVICES is not set +CONFIG_HAVE_IDE=y +# CONFIG_IDE is not set + +# +# SCSI device support +# +# CONFIG_RAID_ATTRS is not set +CONFIG_SCSI=y +CONFIG_SCSI_DMA=y +# CONFIG_SCSI_TGT is not set +# CONFIG_SCSI_NETLINK is not set +# CONFIG_SCSI_PROC_FS is not set + +# +# SCSI support type (disk, tape, CD-ROM) +# +CONFIG_BLK_DEV_SD=y +# CONFIG_CHR_DEV_ST is not set +# CONFIG_CHR_DEV_OSST is not set +CONFIG_BLK_DEV_SR=m +# CONFIG_BLK_DEV_SR_VENDOR is not set +CONFIG_CHR_DEV_SG=m +# CONFIG_CHR_DEV_SCH is not set + +# +# Some SCSI devices (e.g. CD jukebox) support multiple LUNs +# +# CONFIG_SCSI_MULTI_LUN is not set +# CONFIG_SCSI_CONSTANTS is not set +# CONFIG_SCSI_LOGGING is not set +# CONFIG_SCSI_SCAN_ASYNC is not set +CONFIG_SCSI_WAIT_SCAN=m + +# +# SCSI Transports +# +# CONFIG_SCSI_SPI_ATTRS is not set +# CONFIG_SCSI_FC_ATTRS is not set +# CONFIG_SCSI_ISCSI_ATTRS is not set +# CONFIG_SCSI_SAS_LIBSAS is not set +# CONFIG_SCSI_SRP_ATTRS is not set +CONFIG_SCSI_LOWLEVEL=y +# CONFIG_ISCSI_TCP is not set +# CONFIG_BLK_DEV_3W_XXXX_RAID is not set +# CONFIG_SCSI_3W_9XXX is not set +# CONFIG_SCSI_ACARD is not set +# CONFIG_SCSI_AACRAID is not set +# CONFIG_SCSI_AIC7XXX is not set +# CONFIG_SCSI_AIC7XXX_OLD is not set +# CONFIG_SCSI_AIC79XX is not set +# CONFIG_SCSI_AIC94XX is not set +# CONFIG_SCSI_DPT_I2O is not set +# CONFIG_SCSI_ADVANSYS is not set +# CONFIG_SCSI_ARCMSR is not set +# CONFIG_MEGARAID_NEWGEN is not set +# CONFIG_MEGARAID_LEGACY is not set +# CONFIG_MEGARAID_SAS is not set +# CONFIG_SCSI_HPTIOP is not set +# CONFIG_SCSI_DMX3191D is not set +# CONFIG_SCSI_FUTURE_DOMAIN is not set +# CONFIG_SCSI_IPS is not set +# CONFIG_SCSI_INITIO is not set +# CONFIG_SCSI_INIA100 is not set +# CONFIG_SCSI_MVSAS is not set +# CONFIG_SCSI_STEX is not set +# CONFIG_SCSI_SYM53C8XX_2 is not set +# CONFIG_SCSI_IPR is not set +# CONFIG_SCSI_QLOGIC_1280 is not set +# CONFIG_SCSI_QLA_FC is not set +# CONFIG_SCSI_QLA_ISCSI is not set +# CONFIG_SCSI_LPFC is not set +# CONFIG_SCSI_DC395x is not set +# CONFIG_SCSI_DC390T is not set +# CONFIG_SCSI_NSP32 is not set +# CONFIG_SCSI_DEBUG is not set +# CONFIG_SCSI_SRP is not set +CONFIG_ATA=y +# CONFIG_ATA_NONSTANDARD is not set +CONFIG_SATA_PMP=y +# CONFIG_SATA_AHCI is not set +# CONFIG_SATA_SIL24 is not set +CONFIG_ATA_SFF=y +# CONFIG_SATA_SVW is not set +# CONFIG_ATA_PIIX is not set +CONFIG_SATA_MV=y +# CONFIG_SATA_NV is not set +# CONFIG_PDC_ADMA is not set +# CONFIG_SATA_QSTOR is not set +# CONFIG_SATA_PROMISE is not set +# CONFIG_SATA_SX4 is not set +# CONFIG_SATA_SIL is not set +# CONFIG_SATA_SIS is not set +# CONFIG_SATA_ULI is not set +# CONFIG_SATA_VIA is not set +# CONFIG_SATA_VITESSE is not set +# CONFIG_SATA_INIC162X is not set +# CONFIG_PATA_ALI is not set +# CONFIG_PATA_AMD is not set +# CONFIG_PATA_ARTOP is not set +# CONFIG_PATA_ATIIXP is not set +# CONFIG_PATA_CMD640_PCI is not set +# CONFIG_PATA_CMD64X is not set +# CONFIG_PATA_CS5520 is not set +# CONFIG_PATA_CS5530 is not set +# CONFIG_PATA_CYPRESS is not set +# CONFIG_PATA_EFAR is not set +# CONFIG_ATA_GENERIC is not set +# CONFIG_PATA_HPT366 is not set +# CONFIG_PATA_HPT37X is not set +# CONFIG_PATA_HPT3X2N is not set +# CONFIG_PATA_HPT3X3 is not set +# CONFIG_PATA_IT821X is not set +# CONFIG_PATA_IT8213 is not set +# CONFIG_PATA_JMICRON is not set +# CONFIG_PATA_TRIFLEX is not set +# CONFIG_PATA_MARVELL is not set +# CONFIG_PATA_MPIIX is not set +# CONFIG_PATA_OLDPIIX is not set +# CONFIG_PATA_NETCELL is not set +# CONFIG_PATA_NINJA32 is not set +# CONFIG_PATA_NS87410 is not set +# CONFIG_PATA_NS87415 is not set +# CONFIG_PATA_OPTI is not set +# CONFIG_PATA_OPTIDMA is not set +# CONFIG_PATA_PDC_OLD is not set +# CONFIG_PATA_RADISYS is not set +# CONFIG_PATA_RZ1000 is not set +# CONFIG_PATA_SC1200 is not set +# CONFIG_PATA_SERVERWORKS is not set +# CONFIG_PATA_PDC2027X is not set +# CONFIG_PATA_SIL680 is not set +# CONFIG_PATA_SIS is not set +# CONFIG_PATA_VIA is not set +# CONFIG_PATA_WINBOND is not set +# CONFIG_PATA_PLATFORM is not set +# CONFIG_PATA_SCH is not set +# CONFIG_MD is not set +# CONFIG_FUSION is not set + +# +# IEEE 1394 (FireWire) support +# +# CONFIG_FIREWIRE is not set +# CONFIG_IEEE1394 is not set +# CONFIG_I2O is not set +CONFIG_NETDEVICES=y +# CONFIG_NETDEVICES_MULTIQUEUE is not set +# CONFIG_DUMMY is not set +# CONFIG_BONDING is not set +# CONFIG_MACVLAN is not set +# CONFIG_EQUALIZER is not set +# CONFIG_TUN is not set +# CONFIG_VETH is not set +# CONFIG_ARCNET is not set +# CONFIG_PHYLIB is not set +CONFIG_NET_ETHERNET=y +CONFIG_MII=y +# CONFIG_AX88796 is not set +# CONFIG_HAPPYMEAL is not set +# CONFIG_SUNGEM is not set +# CONFIG_CASSINI is not set +# CONFIG_NET_VENDOR_3COM is not set +# CONFIG_SMC91X is not set +# CONFIG_DM9000 is not set +# CONFIG_ENC28J60 is not set +# CONFIG_NET_TULIP is not set +# CONFIG_HP100 is not set +# CONFIG_IBM_NEW_EMAC_ZMII is not set +# CONFIG_IBM_NEW_EMAC_RGMII is not set +# CONFIG_IBM_NEW_EMAC_TAH is not set +# CONFIG_IBM_NEW_EMAC_EMAC4 is not set +CONFIG_NET_PCI=y +# CONFIG_PCNET32 is not set +# CONFIG_AMD8111_ETH is not set +# CONFIG_ADAPTEC_STARFIRE is not set +# CONFIG_B44 is not set +# CONFIG_FORCEDETH is not set +# CONFIG_EEPRO100 is not set +# CONFIG_E100 is not set +# CONFIG_FEALNX is not set +# CONFIG_NATSEMI is not set +# CONFIG_NE2K_PCI is not set +# CONFIG_8139CP is not set +# CONFIG_8139TOO is not set +# CONFIG_R6040 is not set +# CONFIG_SIS900 is not set +# CONFIG_EPIC100 is not set +# CONFIG_SUNDANCE is not set +# CONFIG_TLAN is not set +# CONFIG_VIA_RHINE is not set +# CONFIG_SC92031 is not set +CONFIG_NETDEV_1000=y +# CONFIG_ACENIC is not set +# CONFIG_DL2K is not set +CONFIG_E1000=y +CONFIG_E1000_NAPI=y +# CONFIG_E1000_DISABLE_PACKET_SPLIT is not set +# CONFIG_E1000E is not set +# CONFIG_E1000E_ENABLED is not set +# CONFIG_IP1000 is not set +# CONFIG_IGB is not set +# CONFIG_NS83820 is not set +# CONFIG_HAMACHI is not set +# CONFIG_YELLOWFIN is not set +# CONFIG_R8169 is not set +# CONFIG_SIS190 is not set +# CONFIG_SKGE is not set +# CONFIG_SKY2 is not set +# CONFIG_VIA_VELOCITY is not set +# CONFIG_TIGON3 is not set +# CONFIG_BNX2 is not set +CONFIG_MV643XX_ETH=y +# CONFIG_QLA3XXX is not set +# CONFIG_ATL1 is not set +# CONFIG_NETDEV_10000 is not set +# CONFIG_TR is not set + +# +# Wireless LAN +# +# CONFIG_WLAN_PRE80211 is not set +# CONFIG_WLAN_80211 is not set +# CONFIG_IWLWIFI_LEDS is not set + +# +# USB Network Adapters +# +# CONFIG_USB_CATC is not set +# CONFIG_USB_KAWETH is not set +# CONFIG_USB_PEGASUS is not set +# CONFIG_USB_RTL8150 is not set +# CONFIG_USB_USBNET is not set +# CONFIG_WAN is not set +# CONFIG_FDDI is not set +# CONFIG_HIPPI is not set +# CONFIG_PPP is not set +# CONFIG_SLIP is not set +# CONFIG_NET_FC is not set +# CONFIG_NETCONSOLE is not set +# CONFIG_NETPOLL is not set +# CONFIG_NET_POLL_CONTROLLER is not set +# CONFIG_ISDN is not set + +# +# Input device support +# +CONFIG_INPUT=y +# CONFIG_INPUT_FF_MEMLESS is not set +# CONFIG_INPUT_POLLDEV is not set + +# +# Userland interfaces +# +CONFIG_INPUT_MOUSEDEV=y +CONFIG_INPUT_MOUSEDEV_PSAUX=y +CONFIG_INPUT_MOUSEDEV_SCREEN_X=1024 +CONFIG_INPUT_MOUSEDEV_SCREEN_Y=768 +# CONFIG_INPUT_JOYDEV is not set +# CONFIG_INPUT_EVDEV is not set +# CONFIG_INPUT_EVBUG is not set + +# +# Input Device Drivers +# +# CONFIG_INPUT_KEYBOARD is not set +# CONFIG_INPUT_MOUSE is not set +# CONFIG_INPUT_JOYSTICK is not set +# CONFIG_INPUT_TABLET is not set +# CONFIG_INPUT_TOUCHSCREEN is not set +# CONFIG_INPUT_MISC is not set + +# +# Hardware I/O ports +# +# CONFIG_SERIO is not set +# CONFIG_GAMEPORT is not set + +# +# Character devices +# +# CONFIG_VT is not set +# CONFIG_DEVKMEM is not set +# CONFIG_SERIAL_NONSTANDARD is not set +# CONFIG_NOZOMI is not set + +# +# Serial drivers +# +CONFIG_SERIAL_8250=y +CONFIG_SERIAL_8250_CONSOLE=y +# CONFIG_SERIAL_8250_PCI is not set +CONFIG_SERIAL_8250_NR_UARTS=4 +CONFIG_SERIAL_8250_RUNTIME_UARTS=2 +# CONFIG_SERIAL_8250_EXTENDED is not set + +# +# Non-8250 serial port support +# +CONFIG_SERIAL_CORE=y +CONFIG_SERIAL_CORE_CONSOLE=y +# CONFIG_SERIAL_JSM is not set +CONFIG_UNIX98_PTYS=y +CONFIG_LEGACY_PTYS=y +CONFIG_LEGACY_PTY_COUNT=16 +# CONFIG_IPMI_HANDLER is not set +# CONFIG_HW_RANDOM is not set +# CONFIG_NVRAM is not set +# CONFIG_R3964 is not set +# CONFIG_APPLICOM is not set +# CONFIG_RAW_DRIVER is not set +# CONFIG_TCG_TPM is not set +CONFIG_DEVPORT=y +CONFIG_I2C=y +CONFIG_I2C_BOARDINFO=y +CONFIG_I2C_CHARDEV=y + +# +# I2C Hardware Bus support +# +# CONFIG_I2C_ALI1535 is not set +# CONFIG_I2C_ALI1563 is not set +# CONFIG_I2C_ALI15X3 is not set +# CONFIG_I2C_AMD756 is not set +# CONFIG_I2C_AMD8111 is not set +# CONFIG_I2C_GPIO is not set +# CONFIG_I2C_I801 is not set +# CONFIG_I2C_I810 is not set +# CONFIG_I2C_PIIX4 is not set +# CONFIG_I2C_NFORCE2 is not set +# CONFIG_I2C_OCORES is not set +# CONFIG_I2C_PARPORT_LIGHT is not set +# CONFIG_I2C_PROSAVAGE is not set +# CONFIG_I2C_SAVAGE4 is not set +# CONFIG_I2C_SIMTEC is not set +# CONFIG_I2C_SIS5595 is not set +# CONFIG_I2C_SIS630 is not set +# CONFIG_I2C_SIS96X is not set +# CONFIG_I2C_TAOS_EVM is not set +# CONFIG_I2C_STUB is not set +# CONFIG_I2C_TINY_USB is not set +# CONFIG_I2C_VIA is not set +# CONFIG_I2C_VIAPRO is not set +# CONFIG_I2C_VOODOO3 is not set +# CONFIG_I2C_PCA_PLATFORM is not set +CONFIG_I2C_MV64XXX=y + +# +# Miscellaneous I2C Chip support +# +# CONFIG_DS1682 is not set +# CONFIG_SENSORS_EEPROM is not set +# CONFIG_SENSORS_PCF8574 is not set +# CONFIG_PCF8575 is not set +# CONFIG_SENSORS_PCF8591 is not set +# CONFIG_SENSORS_MAX6875 is not set +# CONFIG_SENSORS_TSL2550 is not set +# CONFIG_I2C_DEBUG_CORE is not set +# CONFIG_I2C_DEBUG_ALGO is not set +# CONFIG_I2C_DEBUG_BUS is not set +# CONFIG_I2C_DEBUG_CHIP is not set +CONFIG_SPI=y +# CONFIG_SPI_DEBUG is not set +CONFIG_SPI_MASTER=y + +# +# SPI Master Controller Drivers +# +# CONFIG_SPI_BITBANG is not set +CONFIG_SPI_ORION=y + +# +# SPI Protocol Masters +# +# CONFIG_SPI_AT25 is not set +# CONFIG_SPI_SPIDEV is not set +# CONFIG_SPI_TLE62X0 is not set +# CONFIG_W1 is not set +# CONFIG_POWER_SUPPLY is not set +# CONFIG_HWMON is not set +# CONFIG_WATCHDOG is not set + +# +# Sonics Silicon Backplane +# +CONFIG_SSB_POSSIBLE=y +# CONFIG_SSB is not set + +# +# Multifunction device drivers +# +# CONFIG_MFD_SM501 is not set +# CONFIG_MFD_ASIC3 is not set +# CONFIG_HTC_PASIC3 is not set + +# +# Multimedia devices +# + +# +# Multimedia core support +# +# CONFIG_VIDEO_DEV is not set +# CONFIG_DVB_CORE is not set +# CONFIG_VIDEO_MEDIA is not set + +# +# Multimedia drivers +# +# CONFIG_DAB is not set + +# +# Graphics support +# +# CONFIG_DRM is not set +# CONFIG_VGASTATE is not set +# CONFIG_VIDEO_OUTPUT_CONTROL is not set +# CONFIG_FB is not set +# CONFIG_BACKLIGHT_LCD_SUPPORT is not set + +# +# Display device support +# +# CONFIG_DISPLAY_SUPPORT is not set + +# +# Sound +# +# CONFIG_SOUND is not set +CONFIG_HID_SUPPORT=y +CONFIG_HID=y +# CONFIG_HID_DEBUG is not set +# CONFIG_HIDRAW is not set + +# +# USB Input Devices +# +CONFIG_USB_HID=y +# CONFIG_USB_HIDINPUT_POWERBOOK is not set +# CONFIG_HID_FF is not set +# CONFIG_USB_HIDDEV is not set +CONFIG_USB_SUPPORT=y +CONFIG_USB_ARCH_HAS_HCD=y +CONFIG_USB_ARCH_HAS_OHCI=y +CONFIG_USB_ARCH_HAS_EHCI=y +CONFIG_USB=y +# CONFIG_USB_DEBUG is not set +# CONFIG_USB_ANNOUNCE_NEW_DEVICES is not set + +# +# Miscellaneous USB options +# +CONFIG_USB_DEVICEFS=y +CONFIG_USB_DEVICE_CLASS=y +# CONFIG_USB_DYNAMIC_MINORS is not set +# CONFIG_USB_OTG is not set +# CONFIG_USB_OTG_WHITELIST is not set +# CONFIG_USB_OTG_BLACKLIST_HUB is not set + +# +# USB Host Controller Drivers +# +# CONFIG_USB_C67X00_HCD is not set +CONFIG_USB_EHCI_HCD=y +CONFIG_USB_EHCI_ROOT_HUB_TT=y +CONFIG_USB_EHCI_TT_NEWSCHED=y +# CONFIG_USB_ISP116X_HCD is not set +# CONFIG_USB_ISP1760_HCD is not set +# CONFIG_USB_OHCI_HCD is not set +# CONFIG_USB_UHCI_HCD is not set +# CONFIG_USB_SL811_HCD is not set +# CONFIG_USB_R8A66597_HCD is not set + +# +# USB Device Class drivers +# +# CONFIG_USB_ACM is not set +CONFIG_USB_PRINTER=y +# CONFIG_USB_WDM is not set + +# +# NOTE: USB_STORAGE enables SCSI, and 'SCSI disk support' +# + +# +# may also be needed; see USB_STORAGE Help for more information +# +CONFIG_USB_STORAGE=y +# CONFIG_USB_STORAGE_DEBUG is not set +CONFIG_USB_STORAGE_DATAFAB=y +CONFIG_USB_STORAGE_FREECOM=y +# CONFIG_USB_STORAGE_ISD200 is not set +CONFIG_USB_STORAGE_DPCM=y +# CONFIG_USB_STORAGE_USBAT is not set +CONFIG_USB_STORAGE_SDDR09=y +CONFIG_USB_STORAGE_SDDR55=y +CONFIG_USB_STORAGE_JUMPSHOT=y +# CONFIG_USB_STORAGE_ALAUDA is not set +# CONFIG_USB_STORAGE_ONETOUCH is not set +# CONFIG_USB_STORAGE_KARMA is not set +# CONFIG_USB_STORAGE_CYPRESS_ATACB is not set +# CONFIG_USB_LIBUSUAL is not set + +# +# USB Imaging devices +# +# CONFIG_USB_MDC800 is not set +# CONFIG_USB_MICROTEK is not set +# CONFIG_USB_MON is not set + +# +# USB port drivers +# +# CONFIG_USB_SERIAL is not set + +# +# USB Miscellaneous drivers +# +# CONFIG_USB_EMI62 is not set +# CONFIG_USB_EMI26 is not set +# CONFIG_USB_ADUTUX is not set +# CONFIG_USB_AUERSWALD is not set +# CONFIG_USB_RIO500 is not set +# CONFIG_USB_LEGOTOWER is not set +# CONFIG_USB_LCD is not set +# CONFIG_USB_BERRY_CHARGE is not set +# CONFIG_USB_LED is not set +# CONFIG_USB_CYPRESS_CY7C63 is not set +# CONFIG_USB_CYTHERM is not set +# CONFIG_USB_PHIDGET is not set +# CONFIG_USB_IDMOUSE is not set +# CONFIG_USB_FTDI_ELAN is not set +# CONFIG_USB_APPLEDISPLAY is not set +# CONFIG_USB_SISUSBVGA is not set +# CONFIG_USB_LD is not set +# CONFIG_USB_TRANCEVIBRATOR is not set +# CONFIG_USB_IOWARRIOR is not set +# CONFIG_USB_TEST is not set +# CONFIG_USB_ISIGHTFW is not set +# CONFIG_USB_GADGET is not set +# CONFIG_MMC is not set +CONFIG_NEW_LEDS=y +# CONFIG_LEDS_CLASS is not set + +# +# LED drivers +# + +# +# LED Triggers +# +# CONFIG_LEDS_TRIGGERS is not set +CONFIG_RTC_LIB=y +CONFIG_RTC_CLASS=y +# CONFIG_RTC_DEBUG is not set + +# +# RTC interfaces +# +CONFIG_RTC_INTF_SYSFS=y +CONFIG_RTC_INTF_PROC=y +CONFIG_RTC_INTF_DEV=y +# CONFIG_RTC_INTF_DEV_UIE_EMUL is not set +# CONFIG_RTC_DRV_TEST is not set + +# +# I2C RTC drivers +# +# CONFIG_RTC_DRV_DS1307 is not set +# CONFIG_RTC_DRV_DS1374 is not set +# CONFIG_RTC_DRV_DS1672 is not set +# CONFIG_RTC_DRV_MAX6900 is not set +CONFIG_RTC_DRV_MV=y +# CONFIG_RTC_DRV_RS5C372 is not set +# CONFIG_RTC_DRV_ISL1208 is not set +# CONFIG_RTC_DRV_X1205 is not set +# CONFIG_RTC_DRV_PCF8563 is not set +# CONFIG_RTC_DRV_PCF8583 is not set +# CONFIG_RTC_DRV_M41T80 is not set +# CONFIG_RTC_DRV_S35390A is not set + +# +# SPI RTC drivers +# +# CONFIG_RTC_DRV_MAX6902 is not set +# CONFIG_RTC_DRV_R9701 is not set +# CONFIG_RTC_DRV_RS5C348 is not set + +# +# Platform RTC drivers +# +# CONFIG_RTC_DRV_CMOS is not set +# CONFIG_RTC_DRV_DS1511 is not set +# CONFIG_RTC_DRV_DS1553 is not set +# CONFIG_RTC_DRV_DS1742 is not set +# CONFIG_RTC_DRV_STK17TA8 is not set +# CONFIG_RTC_DRV_M48T86 is not set +# CONFIG_RTC_DRV_M48T59 is not set +# CONFIG_RTC_DRV_V3020 is not set + +# +# on-CPU RTC drivers +# +CONFIG_DMADEVICES=y + +# +# DMA Devices +# +CONFIG_MV_XOR=y +CONFIG_DMA_ENGINE=y + +# +# DMA Clients +# +# CONFIG_NET_DMA is not set +# CONFIG_UIO is not set + +# +# File systems +# +CONFIG_EXT2_FS=y +# CONFIG_EXT2_FS_XATTR is not set +# CONFIG_EXT2_FS_XIP is not set +CONFIG_EXT3_FS=y +# CONFIG_EXT3_FS_XATTR is not set +# CONFIG_EXT4DEV_FS is not set +CONFIG_JBD=y +# CONFIG_REISERFS_FS is not set +# CONFIG_JFS_FS is not set +# CONFIG_FS_POSIX_ACL is not set +CONFIG_XFS_FS=y +# CONFIG_XFS_QUOTA is not set +# CONFIG_XFS_POSIX_ACL is not set +# CONFIG_XFS_RT is not set +# CONFIG_XFS_DEBUG is not set +# CONFIG_OCFS2_FS is not set +CONFIG_DNOTIFY=y +CONFIG_INOTIFY=y +CONFIG_INOTIFY_USER=y +# CONFIG_QUOTA is not set +# CONFIG_AUTOFS_FS is not set +# CONFIG_AUTOFS4_FS is not set +# CONFIG_FUSE_FS is not set + +# +# CD-ROM/DVD Filesystems +# +CONFIG_ISO9660_FS=y +CONFIG_JOLIET=y +# CONFIG_ZISOFS is not set +CONFIG_UDF_FS=m +CONFIG_UDF_NLS=y + +# +# DOS/FAT/NT Filesystems +# +CONFIG_FAT_FS=y +CONFIG_MSDOS_FS=y +CONFIG_VFAT_FS=y +CONFIG_FAT_DEFAULT_CODEPAGE=437 +CONFIG_FAT_DEFAULT_IOCHARSET="iso8859-1" +# CONFIG_NTFS_FS is not set + +# +# Pseudo filesystems +# +CONFIG_PROC_FS=y +CONFIG_PROC_SYSCTL=y +CONFIG_SYSFS=y +CONFIG_TMPFS=y +# CONFIG_TMPFS_POSIX_ACL is not set +# CONFIG_HUGETLB_PAGE is not set +# CONFIG_CONFIGFS_FS is not set + +# +# Miscellaneous filesystems +# +# CONFIG_ADFS_FS is not set +# CONFIG_AFFS_FS is not set +# CONFIG_HFS_FS is not set +# CONFIG_HFSPLUS_FS is not set +# CONFIG_BEFS_FS is not set +# CONFIG_BFS_FS is not set +# CONFIG_EFS_FS is not set +CONFIG_JFFS2_FS=y +CONFIG_JFFS2_FS_DEBUG=0 +CONFIG_JFFS2_FS_WRITEBUFFER=y +# CONFIG_JFFS2_FS_WBUF_VERIFY is not set +# CONFIG_JFFS2_SUMMARY is not set +# CONFIG_JFFS2_FS_XATTR is not set +# CONFIG_JFFS2_COMPRESSION_OPTIONS is not set +CONFIG_JFFS2_ZLIB=y +# CONFIG_JFFS2_LZO is not set +CONFIG_JFFS2_RTIME=y +# CONFIG_JFFS2_RUBIN is not set +CONFIG_CRAMFS=y +# CONFIG_VXFS_FS is not set +# CONFIG_MINIX_FS is not set +# CONFIG_HPFS_FS is not set +# CONFIG_QNX4FS_FS is not set +# CONFIG_ROMFS_FS is not set +# CONFIG_SYSV_FS is not set +# CONFIG_UFS_FS is not set +CONFIG_NETWORK_FILESYSTEMS=y +CONFIG_NFS_FS=y +CONFIG_NFS_V3=y +# CONFIG_NFS_V3_ACL is not set +# CONFIG_NFS_V4 is not set +# CONFIG_NFSD is not set +CONFIG_ROOT_NFS=y +CONFIG_LOCKD=y +CONFIG_LOCKD_V4=y +CONFIG_NFS_COMMON=y +CONFIG_SUNRPC=y +# CONFIG_SUNRPC_BIND34 is not set +# CONFIG_RPCSEC_GSS_KRB5 is not set +# CONFIG_RPCSEC_GSS_SPKM3 is not set +# CONFIG_SMB_FS is not set +# CONFIG_CIFS is not set +# CONFIG_NCP_FS is not set +# CONFIG_CODA_FS is not set +# CONFIG_AFS_FS is not set + +# +# Partition Types +# +CONFIG_PARTITION_ADVANCED=y +# CONFIG_ACORN_PARTITION is not set +# CONFIG_OSF_PARTITION is not set +# CONFIG_AMIGA_PARTITION is not set +# CONFIG_ATARI_PARTITION is not set +# CONFIG_MAC_PARTITION is not set +CONFIG_MSDOS_PARTITION=y +# CONFIG_BSD_DISKLABEL is not set +# CONFIG_MINIX_SUBPARTITION is not set +# CONFIG_SOLARIS_X86_PARTITION is not set +# CONFIG_UNIXWARE_DISKLABEL is not set +# CONFIG_LDM_PARTITION is not set +# CONFIG_SGI_PARTITION is not set +# CONFIG_ULTRIX_PARTITION is not set +# CONFIG_SUN_PARTITION is not set +# CONFIG_KARMA_PARTITION is not set +# CONFIG_EFI_PARTITION is not set +# CONFIG_SYSV68_PARTITION is not set +CONFIG_NLS=y +CONFIG_NLS_DEFAULT="iso8859-1" +CONFIG_NLS_CODEPAGE_437=y +# CONFIG_NLS_CODEPAGE_737 is not set +# CONFIG_NLS_CODEPAGE_775 is not set +CONFIG_NLS_CODEPAGE_850=y +# CONFIG_NLS_CODEPAGE_852 is not set +# CONFIG_NLS_CODEPAGE_855 is not set +# CONFIG_NLS_CODEPAGE_857 is not set +# CONFIG_NLS_CODEPAGE_860 is not set +# CONFIG_NLS_CODEPAGE_861 is not set +# CONFIG_NLS_CODEPAGE_862 is not set +# CONFIG_NLS_CODEPAGE_863 is not set +# CONFIG_NLS_CODEPAGE_864 is not set +# CONFIG_NLS_CODEPAGE_865 is not set +# CONFIG_NLS_CODEPAGE_866 is not set +# CONFIG_NLS_CODEPAGE_869 is not set +# CONFIG_NLS_CODEPAGE_936 is not set +# CONFIG_NLS_CODEPAGE_950 is not set +# CONFIG_NLS_CODEPAGE_932 is not set +# CONFIG_NLS_CODEPAGE_949 is not set +# CONFIG_NLS_CODEPAGE_874 is not set +# CONFIG_NLS_ISO8859_8 is not set +# CONFIG_NLS_CODEPAGE_1250 is not set +# CONFIG_NLS_CODEPAGE_1251 is not set +# CONFIG_NLS_ASCII is not set +CONFIG_NLS_ISO8859_1=y +CONFIG_NLS_ISO8859_2=y +# CONFIG_NLS_ISO8859_3 is not set +# CONFIG_NLS_ISO8859_4 is not set +# CONFIG_NLS_ISO8859_5 is not set +# CONFIG_NLS_ISO8859_6 is not set +# CONFIG_NLS_ISO8859_7 is not set +# CONFIG_NLS_ISO8859_9 is not set +# CONFIG_NLS_ISO8859_13 is not set +# CONFIG_NLS_ISO8859_14 is not set +# CONFIG_NLS_ISO8859_15 is not set +# CONFIG_NLS_KOI8_R is not set +# CONFIG_NLS_KOI8_U is not set +CONFIG_NLS_UTF8=y +# CONFIG_DLM is not set + +# +# Kernel hacking +# +# CONFIG_PRINTK_TIME is not set +CONFIG_ENABLE_WARN_DEPRECATED=y +CONFIG_ENABLE_MUST_CHECK=y +CONFIG_FRAME_WARN=1024 +CONFIG_MAGIC_SYSRQ=y +# CONFIG_UNUSED_SYMBOLS is not set +# CONFIG_DEBUG_FS is not set +# CONFIG_HEADERS_CHECK is not set +CONFIG_DEBUG_KERNEL=y +# CONFIG_DEBUG_SHIRQ is not set +CONFIG_DETECT_SOFTLOCKUP=y +# CONFIG_SCHED_DEBUG is not set +# CONFIG_SCHEDSTATS is not set +# CONFIG_TIMER_STATS is not set +# CONFIG_DEBUG_OBJECTS is not set +# CONFIG_DEBUG_SLAB is not set +# CONFIG_DEBUG_PREEMPT is not set +# CONFIG_DEBUG_RT_MUTEXES is not set +# CONFIG_RT_MUTEX_TESTER is not set +# CONFIG_DEBUG_SPINLOCK is not set +# CONFIG_DEBUG_MUTEXES is not set +# CONFIG_DEBUG_LOCK_ALLOC is not set +# CONFIG_PROVE_LOCKING is not set +# CONFIG_LOCK_STAT is not set +# CONFIG_DEBUG_SPINLOCK_SLEEP is not set +# CONFIG_DEBUG_LOCKING_API_SELFTESTS is not set +# CONFIG_DEBUG_KOBJECT is not set +# CONFIG_DEBUG_BUGVERBOSE is not set +CONFIG_DEBUG_INFO=y +# CONFIG_DEBUG_VM is not set +# CONFIG_DEBUG_WRITECOUNT is not set +# CONFIG_DEBUG_LIST is not set +# CONFIG_DEBUG_SG is not set +CONFIG_FRAME_POINTER=y +# CONFIG_BOOT_PRINTK_DELAY is not set +# CONFIG_RCU_TORTURE_TEST is not set +# CONFIG_KPROBES_SANITY_TEST is not set +# CONFIG_BACKTRACE_SELF_TEST is not set +# CONFIG_LKDTM is not set +# CONFIG_FAULT_INJECTION is not set +# CONFIG_LATENCYTOP is not set +# CONFIG_SAMPLES is not set +CONFIG_DEBUG_USER=y +CONFIG_DEBUG_ERRORS=y +# CONFIG_DEBUG_STACK_USAGE is not set +CONFIG_DEBUG_LL=y +# CONFIG_DEBUG_ICEDCC is not set + +# +# Security options +# +# CONFIG_KEYS is not set +# CONFIG_SECURITY is not set +# CONFIG_SECURITY_FILE_CAPABILITIES is not set +CONFIG_ASYNC_CORE=y +CONFIG_CRYPTO=y + +# +# Crypto core or helper +# +CONFIG_CRYPTO_ALGAPI=m +CONFIG_CRYPTO_BLKCIPHER=m +CONFIG_CRYPTO_MANAGER=m +# CONFIG_CRYPTO_GF128MUL is not set +# CONFIG_CRYPTO_NULL is not set +# CONFIG_CRYPTO_CRYPTD is not set +# CONFIG_CRYPTO_AUTHENC is not set +# CONFIG_CRYPTO_TEST is not set + +# +# Authenticated Encryption with Associated Data +# +# CONFIG_CRYPTO_CCM is not set +# CONFIG_CRYPTO_GCM is not set +# CONFIG_CRYPTO_SEQIV is not set + +# +# Block modes +# +CONFIG_CRYPTO_CBC=m +# CONFIG_CRYPTO_CTR is not set +# CONFIG_CRYPTO_CTS is not set +CONFIG_CRYPTO_ECB=m +# CONFIG_CRYPTO_LRW is not set +CONFIG_CRYPTO_PCBC=m +# CONFIG_CRYPTO_XTS is not set + +# +# Hash modes +# +# CONFIG_CRYPTO_HMAC is not set +# CONFIG_CRYPTO_XCBC is not set + +# +# Digest +# +# CONFIG_CRYPTO_CRC32C is not set +# CONFIG_CRYPTO_MD4 is not set +# CONFIG_CRYPTO_MD5 is not set +# CONFIG_CRYPTO_MICHAEL_MIC is not set +# CONFIG_CRYPTO_SHA1 is not set +# CONFIG_CRYPTO_SHA256 is not set +# CONFIG_CRYPTO_SHA512 is not set +# CONFIG_CRYPTO_TGR192 is not set +# CONFIG_CRYPTO_WP512 is not set + +# +# Ciphers +# +# CONFIG_CRYPTO_AES is not set +# CONFIG_CRYPTO_ANUBIS is not set +# CONFIG_CRYPTO_ARC4 is not set +# CONFIG_CRYPTO_BLOWFISH is not set +# CONFIG_CRYPTO_CAMELLIA is not set +# CONFIG_CRYPTO_CAST5 is not set +# CONFIG_CRYPTO_CAST6 is not set +# CONFIG_CRYPTO_DES is not set +# CONFIG_CRYPTO_FCRYPT is not set +# CONFIG_CRYPTO_KHAZAD is not set +# CONFIG_CRYPTO_SALSA20 is not set +# CONFIG_CRYPTO_SEED is not set +# CONFIG_CRYPTO_SERPENT is not set +# CONFIG_CRYPTO_TEA is not set +# CONFIG_CRYPTO_TWOFISH is not set + +# +# Compression +# +# CONFIG_CRYPTO_DEFLATE is not set +# CONFIG_CRYPTO_LZO is not set +CONFIG_CRYPTO_HW=y +# CONFIG_CRYPTO_DEV_HIFN_795X is not set + +# +# Library routines +# +CONFIG_BITREVERSE=y +# CONFIG_GENERIC_FIND_FIRST_BIT is not set +# CONFIG_GENERIC_FIND_NEXT_BIT is not set +CONFIG_CRC_CCITT=y +CONFIG_CRC16=y +CONFIG_CRC_ITU_T=m +CONFIG_CRC32=y +# CONFIG_CRC7 is not set +CONFIG_LIBCRC32C=y +CONFIG_ZLIB_INFLATE=y +CONFIG_ZLIB_DEFLATE=y +CONFIG_PLIST=y +CONFIG_HAS_IOMEM=y +CONFIG_HAS_IOPORT=y +CONFIG_HAS_DMA=y diff --git a/arch/arm/configs/ks8695_defconfig b/arch/arm/configs/ks8695_defconfig index 8ab21a0719e..6077f2cb88e 100644 --- a/arch/arm/configs/ks8695_defconfig +++ b/arch/arm/configs/ks8695_defconfig @@ -174,7 +174,6 @@ CONFIG_PCCARD_NONSTATIC=y # Kernel Features # # CONFIG_PREEMPT is not set -# CONFIG_NO_IDLE_HZ is not set CONFIG_HZ=100 # CONFIG_AEABI is not set # CONFIG_ARCH_DISCONTIGMEM_ENABLE is not set diff --git a/arch/arm/configs/loki_defconfig b/arch/arm/configs/loki_defconfig new file mode 100644 index 00000000000..17da7c3b3d5 --- /dev/null +++ b/arch/arm/configs/loki_defconfig @@ -0,0 +1,1147 @@ +# +# Automatically generated make config: don't edit +# Linux kernel version: 2.6.26-rc5 +# Fri Jun 13 03:07:49 2008 +# +CONFIG_ARM=y +CONFIG_SYS_SUPPORTS_APM_EMULATION=y +# CONFIG_GENERIC_GPIO is not set +CONFIG_GENERIC_TIME=y +CONFIG_GENERIC_CLOCKEVENTS=y +CONFIG_MMU=y +# CONFIG_NO_IOPORT is not set +CONFIG_GENERIC_HARDIRQS=y +CONFIG_STACKTRACE_SUPPORT=y +CONFIG_HAVE_LATENCYTOP_SUPPORT=y +CONFIG_LOCKDEP_SUPPORT=y +CONFIG_TRACE_IRQFLAGS_SUPPORT=y +CONFIG_HARDIRQS_SW_RESEND=y +CONFIG_GENERIC_IRQ_PROBE=y +CONFIG_RWSEM_GENERIC_SPINLOCK=y +# CONFIG_ARCH_HAS_ILOG2_U32 is not set +# CONFIG_ARCH_HAS_ILOG2_U64 is not set +CONFIG_GENERIC_HWEIGHT=y +CONFIG_GENERIC_CALIBRATE_DELAY=y +CONFIG_ARCH_SUPPORTS_AOUT=y +CONFIG_ZONE_DMA=y +CONFIG_VECTORS_BASE=0xffff0000 +CONFIG_DEFCONFIG_LIST="/lib/modules/$UNAME_RELEASE/.config" + +# +# General setup +# +CONFIG_EXPERIMENTAL=y +CONFIG_BROKEN_ON_SMP=y +CONFIG_LOCK_KERNEL=y +CONFIG_INIT_ENV_ARG_LIMIT=32 +CONFIG_LOCALVERSION="" +CONFIG_LOCALVERSION_AUTO=y +CONFIG_SWAP=y +CONFIG_SYSVIPC=y +CONFIG_SYSVIPC_SYSCTL=y +# CONFIG_POSIX_MQUEUE is not set +# CONFIG_BSD_PROCESS_ACCT is not set +# CONFIG_TASKSTATS is not set +# CONFIG_AUDIT is not set +# CONFIG_IKCONFIG is not set +CONFIG_LOG_BUF_SHIFT=14 +# CONFIG_CGROUPS is not set +# CONFIG_GROUP_SCHED is not set +# CONFIG_SYSFS_DEPRECATED_V2 is not set +# CONFIG_RELAY is not set +# CONFIG_NAMESPACES is not set +# CONFIG_BLK_DEV_INITRD is not set +CONFIG_CC_OPTIMIZE_FOR_SIZE=y +CONFIG_SYSCTL=y +CONFIG_EMBEDDED=y +CONFIG_UID16=y +CONFIG_SYSCTL_SYSCALL=y +CONFIG_SYSCTL_SYSCALL_CHECK=y +CONFIG_KALLSYMS=y +# CONFIG_KALLSYMS_EXTRA_PASS is not set +CONFIG_HOTPLUG=y +CONFIG_PRINTK=y +CONFIG_BUG=y +CONFIG_ELF_CORE=y +CONFIG_COMPAT_BRK=y +CONFIG_BASE_FULL=y +CONFIG_FUTEX=y +CONFIG_ANON_INODES=y +CONFIG_EPOLL=y +CONFIG_SIGNALFD=y +CONFIG_TIMERFD=y +CONFIG_EVENTFD=y +CONFIG_SHMEM=y +CONFIG_VM_EVENT_COUNTERS=y +CONFIG_SLAB=y +# CONFIG_SLUB is not set +# CONFIG_SLOB is not set +# CONFIG_PROFILING is not set +# CONFIG_MARKERS is not set +CONFIG_HAVE_OPROFILE=y +# CONFIG_KPROBES is not set +CONFIG_HAVE_KPROBES=y +CONFIG_HAVE_KRETPROBES=y +# CONFIG_HAVE_DMA_ATTRS is not set +CONFIG_PROC_PAGE_MONITOR=y +CONFIG_SLABINFO=y +CONFIG_RT_MUTEXES=y +# CONFIG_TINY_SHMEM is not set +CONFIG_BASE_SMALL=0 +CONFIG_MODULES=y +# CONFIG_MODULE_FORCE_LOAD is not set +CONFIG_MODULE_UNLOAD=y +# CONFIG_MODULE_FORCE_UNLOAD is not set +# CONFIG_MODVERSIONS is not set +# CONFIG_MODULE_SRCVERSION_ALL is not set +# CONFIG_KMOD is not set +CONFIG_BLOCK=y +# CONFIG_LBD is not set +# CONFIG_BLK_DEV_IO_TRACE is not set +# CONFIG_LSF is not set +# CONFIG_BLK_DEV_BSG is not set + +# +# IO Schedulers +# +CONFIG_IOSCHED_NOOP=y +CONFIG_IOSCHED_AS=y +CONFIG_IOSCHED_DEADLINE=y +CONFIG_IOSCHED_CFQ=y +# CONFIG_DEFAULT_AS is not set +# CONFIG_DEFAULT_DEADLINE is not set +CONFIG_DEFAULT_CFQ=y +# CONFIG_DEFAULT_NOOP is not set +CONFIG_DEFAULT_IOSCHED="cfq" +CONFIG_CLASSIC_RCU=y + +# +# System Type +# +# CONFIG_ARCH_AAEC2000 is not set +# CONFIG_ARCH_INTEGRATOR is not set +# CONFIG_ARCH_REALVIEW is not set +# CONFIG_ARCH_VERSATILE is not set +# CONFIG_ARCH_AT91 is not set +# CONFIG_ARCH_CLPS7500 is not set +# CONFIG_ARCH_CLPS711X is not set +# CONFIG_ARCH_CO285 is not set +# CONFIG_ARCH_EBSA110 is not set +# CONFIG_ARCH_EP93XX is not set +# CONFIG_ARCH_FOOTBRIDGE is not set +# CONFIG_ARCH_NETX is not set +# CONFIG_ARCH_H720X is not set +# CONFIG_ARCH_IMX is not set +# CONFIG_ARCH_IOP13XX is not set +# CONFIG_ARCH_IOP32X is not set +# CONFIG_ARCH_IOP33X is not set +# CONFIG_ARCH_IXP23XX is not set +# CONFIG_ARCH_IXP2000 is not set +# CONFIG_ARCH_IXP4XX is not set +# CONFIG_ARCH_L7200 is not set +# CONFIG_ARCH_KIRKWOOD is not set +# CONFIG_ARCH_KS8695 is not set +# CONFIG_ARCH_NS9XXX is not set +CONFIG_ARCH_LOKI=y +# CONFIG_ARCH_MV78XX0 is not set +# CONFIG_ARCH_MXC is not set +# CONFIG_ARCH_ORION5X is not set +# CONFIG_ARCH_PNX4008 is not set +# CONFIG_ARCH_PXA is not set +# CONFIG_ARCH_RPC is not set +# CONFIG_ARCH_SA1100 is not set +# CONFIG_ARCH_S3C2410 is not set +# CONFIG_ARCH_SHARK is not set +# CONFIG_ARCH_LH7A40X is not set +# CONFIG_ARCH_DAVINCI is not set +# CONFIG_ARCH_OMAP is not set +# CONFIG_ARCH_MSM7X00A is not set + +# +# Marvell Loki (88RC8480) Implementations +# +CONFIG_MACH_LB88RC8480=y + +# +# Boot options +# + +# +# Power management +# +CONFIG_PLAT_ORION=y + +# +# Processor Type +# +CONFIG_CPU_32=y +CONFIG_CPU_FEROCEON=y +# CONFIG_CPU_FEROCEON_OLD_ID is not set +CONFIG_CPU_32v5=y +CONFIG_CPU_ABRT_EV5T=y +CONFIG_CPU_PABRT_NOIFAR=y +CONFIG_CPU_CACHE_VIVT=y +CONFIG_CPU_COPY_FEROCEON=y +CONFIG_CPU_TLB_FEROCEON=y +CONFIG_CPU_CP15=y +CONFIG_CPU_CP15_MMU=y + +# +# Processor Features +# +CONFIG_ARM_THUMB=y +# CONFIG_CPU_ICACHE_DISABLE is not set +# CONFIG_CPU_DCACHE_DISABLE is not set +# CONFIG_OUTER_CACHE is not set + +# +# Bus support +# +# CONFIG_PCI_SYSCALL is not set +# CONFIG_ARCH_SUPPORTS_MSI is not set +# CONFIG_PCCARD is not set + +# +# Kernel Features +# +CONFIG_TICK_ONESHOT=y +CONFIG_NO_HZ=y +CONFIG_HIGH_RES_TIMERS=y +CONFIG_GENERIC_CLOCKEVENTS_BUILD=y +CONFIG_PREEMPT=y +CONFIG_HZ=100 +CONFIG_AEABI=y +CONFIG_OABI_COMPAT=y +# CONFIG_ARCH_DISCONTIGMEM_ENABLE is not set +CONFIG_SELECT_MEMORY_MODEL=y +CONFIG_FLATMEM_MANUAL=y +# CONFIG_DISCONTIGMEM_MANUAL is not set +# CONFIG_SPARSEMEM_MANUAL is not set +CONFIG_FLATMEM=y +CONFIG_FLAT_NODE_MEM_MAP=y +# CONFIG_SPARSEMEM_STATIC is not set +# CONFIG_SPARSEMEM_VMEMMAP_ENABLE is not set +CONFIG_PAGEFLAGS_EXTENDED=y +CONFIG_SPLIT_PTLOCK_CPUS=4096 +# CONFIG_RESOURCES_64BIT is not set +CONFIG_ZONE_DMA_FLAG=1 +CONFIG_BOUNCE=y +CONFIG_VIRT_TO_BUS=y +CONFIG_ALIGNMENT_TRAP=y + +# +# Boot options +# +CONFIG_ZBOOT_ROM_TEXT=0x0 +CONFIG_ZBOOT_ROM_BSS=0x0 +CONFIG_CMDLINE="" +# CONFIG_XIP_KERNEL is not set +# CONFIG_KEXEC is not set + +# +# Floating point emulation +# + +# +# At least one emulation must be selected +# +# CONFIG_FPE_NWFPE is not set +# CONFIG_FPE_FASTFPE is not set +# CONFIG_VFP is not set + +# +# Userspace binary formats +# +CONFIG_BINFMT_ELF=y +# CONFIG_BINFMT_AOUT is not set +# CONFIG_BINFMT_MISC is not set + +# +# Power management options +# +# CONFIG_PM is not set +CONFIG_ARCH_SUSPEND_POSSIBLE=y + +# +# Networking +# +CONFIG_NET=y + +# +# Networking options +# +CONFIG_PACKET=y +CONFIG_PACKET_MMAP=y +CONFIG_UNIX=y +CONFIG_XFRM=y +# CONFIG_XFRM_USER is not set +# CONFIG_XFRM_SUB_POLICY is not set +# CONFIG_XFRM_MIGRATE is not set +# CONFIG_XFRM_STATISTICS is not set +# CONFIG_NET_KEY is not set +CONFIG_INET=y +CONFIG_IP_MULTICAST=y +# CONFIG_IP_ADVANCED_ROUTER is not set +CONFIG_IP_FIB_HASH=y +CONFIG_IP_PNP=y +CONFIG_IP_PNP_DHCP=y +CONFIG_IP_PNP_BOOTP=y +# CONFIG_IP_PNP_RARP is not set +# CONFIG_NET_IPIP is not set +# CONFIG_NET_IPGRE is not set +# CONFIG_IP_MROUTE is not set +# CONFIG_ARPD is not set +# CONFIG_SYN_COOKIES is not set +# CONFIG_INET_AH is not set +# CONFIG_INET_ESP is not set +# CONFIG_INET_IPCOMP is not set +# CONFIG_INET_XFRM_TUNNEL is not set +# CONFIG_INET_TUNNEL is not set +CONFIG_INET_XFRM_MODE_TRANSPORT=y +CONFIG_INET_XFRM_MODE_TUNNEL=y +CONFIG_INET_XFRM_MODE_BEET=y +# CONFIG_INET_LRO is not set +CONFIG_INET_DIAG=y +CONFIG_INET_TCP_DIAG=y +# CONFIG_TCP_CONG_ADVANCED is not set +CONFIG_TCP_CONG_CUBIC=y +CONFIG_DEFAULT_TCP_CONG="cubic" +# CONFIG_TCP_MD5SIG is not set +# CONFIG_IPV6 is not set +# CONFIG_NETWORK_SECMARK is not set +# CONFIG_NETFILTER is not set +# CONFIG_IP_DCCP is not set +# CONFIG_IP_SCTP is not set +# CONFIG_TIPC is not set +# CONFIG_ATM is not set +# CONFIG_BRIDGE is not set +# CONFIG_VLAN_8021Q is not set +# CONFIG_DECNET is not set +# CONFIG_LLC2 is not set +# CONFIG_IPX is not set +# CONFIG_ATALK is not set +# CONFIG_X25 is not set +# CONFIG_LAPB is not set +# CONFIG_ECONET is not set +# CONFIG_WAN_ROUTER is not set +# CONFIG_NET_SCHED is not set + +# +# Network testing +# +CONFIG_NET_PKTGEN=m +# CONFIG_HAMRADIO is not set +# CONFIG_CAN is not set +# CONFIG_IRDA is not set +# CONFIG_BT is not set +# CONFIG_AF_RXRPC is not set + +# +# Wireless +# +# CONFIG_CFG80211 is not set +CONFIG_WIRELESS_EXT=y +# CONFIG_MAC80211 is not set +# CONFIG_IEEE80211 is not set +# CONFIG_RFKILL is not set +# CONFIG_NET_9P is not set + +# +# Device Drivers +# + +# +# Generic Driver Options +# +CONFIG_UEVENT_HELPER_PATH="/sbin/hotplug" +CONFIG_STANDALONE=y +CONFIG_PREVENT_FIRMWARE_BUILD=y +CONFIG_FW_LOADER=y +# CONFIG_SYS_HYPERVISOR is not set +# CONFIG_CONNECTOR is not set +CONFIG_MTD=y +# CONFIG_MTD_DEBUG is not set +# CONFIG_MTD_CONCAT is not set +CONFIG_MTD_PARTITIONS=y +# CONFIG_MTD_REDBOOT_PARTS is not set +CONFIG_MTD_CMDLINE_PARTS=y +# CONFIG_MTD_AFS_PARTS is not set +# CONFIG_MTD_AR7_PARTS is not set + +# +# User Modules And Translation Layers +# +CONFIG_MTD_CHAR=y +CONFIG_MTD_BLKDEVS=y +CONFIG_MTD_BLOCK=y +CONFIG_FTL=y +CONFIG_NFTL=y +# CONFIG_NFTL_RW is not set +# CONFIG_INFTL is not set +# CONFIG_RFD_FTL is not set +# CONFIG_SSFDC is not set +# CONFIG_MTD_OOPS is not set + +# +# RAM/ROM/Flash chip drivers +# +CONFIG_MTD_CFI=y +CONFIG_MTD_JEDECPROBE=y +CONFIG_MTD_GEN_PROBE=y +CONFIG_MTD_CFI_ADV_OPTIONS=y +CONFIG_MTD_CFI_NOSWAP=y +# CONFIG_MTD_CFI_BE_BYTE_SWAP is not set +# CONFIG_MTD_CFI_LE_BYTE_SWAP is not set +CONFIG_MTD_CFI_GEOMETRY=y +CONFIG_MTD_MAP_BANK_WIDTH_1=y +CONFIG_MTD_MAP_BANK_WIDTH_2=y +CONFIG_MTD_MAP_BANK_WIDTH_4=y +# CONFIG_MTD_MAP_BANK_WIDTH_8 is not set +# CONFIG_MTD_MAP_BANK_WIDTH_16 is not set +# CONFIG_MTD_MAP_BANK_WIDTH_32 is not set +CONFIG_MTD_CFI_I1=y +CONFIG_MTD_CFI_I2=y +CONFIG_MTD_CFI_I4=y +# CONFIG_MTD_CFI_I8 is not set +# CONFIG_MTD_OTP is not set +CONFIG_MTD_CFI_INTELEXT=y +CONFIG_MTD_CFI_AMDSTD=y +CONFIG_MTD_CFI_STAA=y +CONFIG_MTD_CFI_UTIL=y +# CONFIG_MTD_RAM is not set +# CONFIG_MTD_ROM is not set +# CONFIG_MTD_ABSENT is not set + +# +# Mapping drivers for chip access +# +# CONFIG_MTD_COMPLEX_MAPPINGS is not set +CONFIG_MTD_PHYSMAP=y +CONFIG_MTD_PHYSMAP_START=0x0 +CONFIG_MTD_PHYSMAP_LEN=0x0 +CONFIG_MTD_PHYSMAP_BANKWIDTH=0 +# CONFIG_MTD_ARM_INTEGRATOR is not set +# CONFIG_MTD_IMPA7 is not set +# CONFIG_MTD_PLATRAM is not set + +# +# Self-contained MTD device drivers +# +# CONFIG_MTD_DATAFLASH is not set +CONFIG_MTD_M25P80=y +CONFIG_M25PXX_USE_FAST_READ=y +# CONFIG_MTD_SLRAM is not set +# CONFIG_MTD_PHRAM is not set +# CONFIG_MTD_MTDRAM is not set +# CONFIG_MTD_BLOCK2MTD is not set + +# +# Disk-On-Chip Device Drivers +# +# CONFIG_MTD_DOC2000 is not set +# CONFIG_MTD_DOC2001 is not set +# CONFIG_MTD_DOC2001PLUS is not set +CONFIG_MTD_NAND=y +CONFIG_MTD_NAND_VERIFY_WRITE=y +# CONFIG_MTD_NAND_ECC_SMC is not set +# CONFIG_MTD_NAND_MUSEUM_IDS is not set +CONFIG_MTD_NAND_IDS=y +# CONFIG_MTD_NAND_DISKONCHIP is not set +# CONFIG_MTD_NAND_NANDSIM is not set +# CONFIG_MTD_NAND_PLATFORM is not set +# CONFIG_MTD_ALAUDA is not set +CONFIG_MTD_NAND_ORION=y +# CONFIG_MTD_ONENAND is not set + +# +# UBI - Unsorted block images +# +# CONFIG_MTD_UBI is not set +# CONFIG_PARPORT is not set +CONFIG_BLK_DEV=y +# CONFIG_BLK_DEV_COW_COMMON is not set +CONFIG_BLK_DEV_LOOP=y +# CONFIG_BLK_DEV_CRYPTOLOOP is not set +# CONFIG_BLK_DEV_NBD is not set +# CONFIG_BLK_DEV_UB is not set +# CONFIG_BLK_DEV_RAM is not set +# CONFIG_CDROM_PKTCDVD is not set +# CONFIG_ATA_OVER_ETH is not set +# CONFIG_MISC_DEVICES is not set +CONFIG_HAVE_IDE=y +# CONFIG_IDE is not set + +# +# SCSI device support +# +# CONFIG_RAID_ATTRS is not set +CONFIG_SCSI=y +CONFIG_SCSI_DMA=y +# CONFIG_SCSI_TGT is not set +# CONFIG_SCSI_NETLINK is not set +# CONFIG_SCSI_PROC_FS is not set + +# +# SCSI support type (disk, tape, CD-ROM) +# +CONFIG_BLK_DEV_SD=y +# CONFIG_CHR_DEV_ST is not set +# CONFIG_CHR_DEV_OSST is not set +CONFIG_BLK_DEV_SR=m +# CONFIG_BLK_DEV_SR_VENDOR is not set +CONFIG_CHR_DEV_SG=m +# CONFIG_CHR_DEV_SCH is not set + +# +# Some SCSI devices (e.g. CD jukebox) support multiple LUNs +# +# CONFIG_SCSI_MULTI_LUN is not set +# CONFIG_SCSI_CONSTANTS is not set +# CONFIG_SCSI_LOGGING is not set +# CONFIG_SCSI_SCAN_ASYNC is not set +CONFIG_SCSI_WAIT_SCAN=m + +# +# SCSI Transports +# +# CONFIG_SCSI_SPI_ATTRS is not set +# CONFIG_SCSI_FC_ATTRS is not set +# CONFIG_SCSI_ISCSI_ATTRS is not set +# CONFIG_SCSI_SAS_LIBSAS is not set +# CONFIG_SCSI_SRP_ATTRS is not set +CONFIG_SCSI_LOWLEVEL=y +# CONFIG_ISCSI_TCP is not set +# CONFIG_SCSI_DEBUG is not set +CONFIG_ATA=y +# CONFIG_ATA_NONSTANDARD is not set +CONFIG_SATA_PMP=y +CONFIG_ATA_SFF=y +CONFIG_SATA_MV=y +# CONFIG_PATA_PLATFORM is not set +# CONFIG_MD is not set +CONFIG_NETDEVICES=y +# CONFIG_NETDEVICES_MULTIQUEUE is not set +# CONFIG_DUMMY is not set +# CONFIG_BONDING is not set +# CONFIG_MACVLAN is not set +# CONFIG_EQUALIZER is not set +# CONFIG_TUN is not set +# CONFIG_VETH is not set +# CONFIG_PHYLIB is not set +CONFIG_NET_ETHERNET=y +CONFIG_MII=y +# CONFIG_AX88796 is not set +# CONFIG_SMC91X is not set +# CONFIG_DM9000 is not set +# CONFIG_ENC28J60 is not set +# CONFIG_IBM_NEW_EMAC_ZMII is not set +# CONFIG_IBM_NEW_EMAC_RGMII is not set +# CONFIG_IBM_NEW_EMAC_TAH is not set +# CONFIG_IBM_NEW_EMAC_EMAC4 is not set +# CONFIG_B44 is not set +CONFIG_NETDEV_1000=y +# CONFIG_E1000E_ENABLED is not set +CONFIG_MV643XX_ETH=y +# CONFIG_NETDEV_10000 is not set + +# +# Wireless LAN +# +# CONFIG_WLAN_PRE80211 is not set +# CONFIG_WLAN_80211 is not set +# CONFIG_IWLWIFI_LEDS is not set + +# +# USB Network Adapters +# +# CONFIG_USB_CATC is not set +# CONFIG_USB_KAWETH is not set +# CONFIG_USB_PEGASUS is not set +# CONFIG_USB_RTL8150 is not set +# CONFIG_USB_USBNET is not set +# CONFIG_WAN is not set +# CONFIG_PPP is not set +# CONFIG_SLIP is not set +# CONFIG_NETCONSOLE is not set +# CONFIG_NETPOLL is not set +# CONFIG_NET_POLL_CONTROLLER is not set +# CONFIG_ISDN is not set + +# +# Input device support +# +CONFIG_INPUT=y +# CONFIG_INPUT_FF_MEMLESS is not set +# CONFIG_INPUT_POLLDEV is not set + +# +# Userland interfaces +# +CONFIG_INPUT_MOUSEDEV=y +CONFIG_INPUT_MOUSEDEV_PSAUX=y +CONFIG_INPUT_MOUSEDEV_SCREEN_X=1024 +CONFIG_INPUT_MOUSEDEV_SCREEN_Y=768 +# CONFIG_INPUT_JOYDEV is not set +# CONFIG_INPUT_EVDEV is not set +# CONFIG_INPUT_EVBUG is not set + +# +# Input Device Drivers +# +# CONFIG_INPUT_KEYBOARD is not set +# CONFIG_INPUT_MOUSE is not set +# CONFIG_INPUT_JOYSTICK is not set +# CONFIG_INPUT_TABLET is not set +# CONFIG_INPUT_TOUCHSCREEN is not set +# CONFIG_INPUT_MISC is not set + +# +# Hardware I/O ports +# +# CONFIG_SERIO is not set +# CONFIG_GAMEPORT is not set + +# +# Character devices +# +CONFIG_VT=y +CONFIG_VT_CONSOLE=y +CONFIG_HW_CONSOLE=y +# CONFIG_VT_HW_CONSOLE_BINDING is not set +CONFIG_DEVKMEM=y +# CONFIG_SERIAL_NONSTANDARD is not set + +# +# Serial drivers +# +CONFIG_SERIAL_8250=y +CONFIG_SERIAL_8250_CONSOLE=y +CONFIG_SERIAL_8250_NR_UARTS=4 +CONFIG_SERIAL_8250_RUNTIME_UARTS=2 +# CONFIG_SERIAL_8250_EXTENDED is not set + +# +# Non-8250 serial port support +# +CONFIG_SERIAL_CORE=y +CONFIG_SERIAL_CORE_CONSOLE=y +CONFIG_UNIX98_PTYS=y +CONFIG_LEGACY_PTYS=y +CONFIG_LEGACY_PTY_COUNT=16 +# CONFIG_IPMI_HANDLER is not set +CONFIG_HW_RANDOM=m +# CONFIG_NVRAM is not set +# CONFIG_R3964 is not set +# CONFIG_RAW_DRIVER is not set +# CONFIG_TCG_TPM is not set +CONFIG_I2C=y +CONFIG_I2C_BOARDINFO=y +CONFIG_I2C_CHARDEV=y + +# +# I2C Hardware Bus support +# +# CONFIG_I2C_OCORES is not set +# CONFIG_I2C_PARPORT_LIGHT is not set +# CONFIG_I2C_SIMTEC is not set +# CONFIG_I2C_TAOS_EVM is not set +# CONFIG_I2C_STUB is not set +# CONFIG_I2C_TINY_USB is not set +# CONFIG_I2C_PCA_PLATFORM is not set +CONFIG_I2C_MV64XXX=y + +# +# Miscellaneous I2C Chip support +# +# CONFIG_DS1682 is not set +# CONFIG_SENSORS_EEPROM is not set +# CONFIG_SENSORS_PCF8574 is not set +# CONFIG_PCF8575 is not set +# CONFIG_SENSORS_PCF8591 is not set +# CONFIG_SENSORS_MAX6875 is not set +# CONFIG_SENSORS_TSL2550 is not set +# CONFIG_I2C_DEBUG_CORE is not set +# CONFIG_I2C_DEBUG_ALGO is not set +# CONFIG_I2C_DEBUG_BUS is not set +# CONFIG_I2C_DEBUG_CHIP is not set +CONFIG_SPI=y +CONFIG_SPI_MASTER=y + +# +# SPI Master Controller Drivers +# +# CONFIG_SPI_BITBANG is not set + +# +# SPI Protocol Masters +# +# CONFIG_SPI_AT25 is not set +# CONFIG_SPI_SPIDEV is not set +# CONFIG_SPI_TLE62X0 is not set +# CONFIG_W1 is not set +# CONFIG_POWER_SUPPLY is not set +# CONFIG_HWMON is not set +# CONFIG_WATCHDOG is not set + +# +# Sonics Silicon Backplane +# +CONFIG_SSB_POSSIBLE=y +# CONFIG_SSB is not set + +# +# Multifunction device drivers +# +# CONFIG_MFD_SM501 is not set +# CONFIG_MFD_ASIC3 is not set +# CONFIG_HTC_PASIC3 is not set + +# +# Multimedia devices +# + +# +# Multimedia core support +# +# CONFIG_VIDEO_DEV is not set +# CONFIG_DVB_CORE is not set +# CONFIG_VIDEO_MEDIA is not set + +# +# Multimedia drivers +# +# CONFIG_DAB is not set + +# +# Graphics support +# +# CONFIG_VGASTATE is not set +# CONFIG_VIDEO_OUTPUT_CONTROL is not set +# CONFIG_FB is not set +# CONFIG_BACKLIGHT_LCD_SUPPORT is not set + +# +# Display device support +# +# CONFIG_DISPLAY_SUPPORT is not set + +# +# Console display driver support +# +# CONFIG_VGA_CONSOLE is not set +CONFIG_DUMMY_CONSOLE=y + +# +# Sound +# +# CONFIG_SOUND is not set +CONFIG_HID_SUPPORT=y +CONFIG_HID=y +# CONFIG_HID_DEBUG is not set +# CONFIG_HIDRAW is not set + +# +# USB Input Devices +# +CONFIG_USB_HID=y +# CONFIG_USB_HIDINPUT_POWERBOOK is not set +# CONFIG_HID_FF is not set +# CONFIG_USB_HIDDEV is not set +CONFIG_USB_SUPPORT=y +CONFIG_USB_ARCH_HAS_HCD=y +# CONFIG_USB_ARCH_HAS_OHCI is not set +# CONFIG_USB_ARCH_HAS_EHCI is not set +CONFIG_USB=y +# CONFIG_USB_DEBUG is not set +# CONFIG_USB_ANNOUNCE_NEW_DEVICES is not set + +# +# Miscellaneous USB options +# +CONFIG_USB_DEVICEFS=y +CONFIG_USB_DEVICE_CLASS=y +# CONFIG_USB_DYNAMIC_MINORS is not set +# CONFIG_USB_OTG is not set +# CONFIG_USB_OTG_WHITELIST is not set +# CONFIG_USB_OTG_BLACKLIST_HUB is not set + +# +# USB Host Controller Drivers +# +# CONFIG_USB_C67X00_HCD is not set +# CONFIG_USB_ISP116X_HCD is not set +# CONFIG_USB_ISP1760_HCD is not set +# CONFIG_USB_SL811_HCD is not set +# CONFIG_USB_R8A66597_HCD is not set + +# +# USB Device Class drivers +# +# CONFIG_USB_ACM is not set +CONFIG_USB_PRINTER=y +# CONFIG_USB_WDM is not set + +# +# NOTE: USB_STORAGE enables SCSI, and 'SCSI disk support' +# + +# +# may also be needed; see USB_STORAGE Help for more information +# +CONFIG_USB_STORAGE=y +# CONFIG_USB_STORAGE_DEBUG is not set +CONFIG_USB_STORAGE_DATAFAB=y +CONFIG_USB_STORAGE_FREECOM=y +# CONFIG_USB_STORAGE_ISD200 is not set +CONFIG_USB_STORAGE_DPCM=y +# CONFIG_USB_STORAGE_USBAT is not set +CONFIG_USB_STORAGE_SDDR09=y +CONFIG_USB_STORAGE_SDDR55=y +CONFIG_USB_STORAGE_JUMPSHOT=y +# CONFIG_USB_STORAGE_ALAUDA is not set +# CONFIG_USB_STORAGE_ONETOUCH is not set +# CONFIG_USB_STORAGE_KARMA is not set +# CONFIG_USB_STORAGE_CYPRESS_ATACB is not set +# CONFIG_USB_LIBUSUAL is not set + +# +# USB Imaging devices +# +# CONFIG_USB_MDC800 is not set +# CONFIG_USB_MICROTEK is not set +# CONFIG_USB_MON is not set + +# +# USB port drivers +# +# CONFIG_USB_SERIAL is not set + +# +# USB Miscellaneous drivers +# +# CONFIG_USB_EMI62 is not set +# CONFIG_USB_EMI26 is not set +# CONFIG_USB_ADUTUX is not set +# CONFIG_USB_AUERSWALD is not set +# CONFIG_USB_RIO500 is not set +# CONFIG_USB_LEGOTOWER is not set +# CONFIG_USB_LCD is not set +# CONFIG_USB_BERRY_CHARGE is not set +# CONFIG_USB_LED is not set +# CONFIG_USB_CYPRESS_CY7C63 is not set +# CONFIG_USB_CYTHERM is not set +# CONFIG_USB_PHIDGET is not set +# CONFIG_USB_IDMOUSE is not set +# CONFIG_USB_FTDI_ELAN is not set +# CONFIG_USB_APPLEDISPLAY is not set +# CONFIG_USB_LD is not set +# CONFIG_USB_TRANCEVIBRATOR is not set +# CONFIG_USB_IOWARRIOR is not set +# CONFIG_USB_TEST is not set +# CONFIG_USB_ISIGHTFW is not set +# CONFIG_USB_GADGET is not set +# CONFIG_MMC is not set +CONFIG_NEW_LEDS=y +# CONFIG_LEDS_CLASS is not set + +# +# LED drivers +# + +# +# LED Triggers +# +# CONFIG_LEDS_TRIGGERS is not set +CONFIG_RTC_LIB=y +# CONFIG_RTC_CLASS is not set +# CONFIG_UIO is not set + +# +# File systems +# +CONFIG_EXT2_FS=y +# CONFIG_EXT2_FS_XATTR is not set +# CONFIG_EXT2_FS_XIP is not set +CONFIG_EXT3_FS=y +# CONFIG_EXT3_FS_XATTR is not set +# CONFIG_EXT4DEV_FS is not set +CONFIG_JBD=y +# CONFIG_REISERFS_FS is not set +# CONFIG_JFS_FS is not set +# CONFIG_FS_POSIX_ACL is not set +CONFIG_XFS_FS=y +# CONFIG_XFS_QUOTA is not set +# CONFIG_XFS_POSIX_ACL is not set +# CONFIG_XFS_RT is not set +# CONFIG_XFS_DEBUG is not set +# CONFIG_OCFS2_FS is not set +CONFIG_DNOTIFY=y +CONFIG_INOTIFY=y +CONFIG_INOTIFY_USER=y +# CONFIG_QUOTA is not set +# CONFIG_AUTOFS_FS is not set +# CONFIG_AUTOFS4_FS is not set +# CONFIG_FUSE_FS is not set + +# +# CD-ROM/DVD Filesystems +# +CONFIG_ISO9660_FS=y +# CONFIG_JOLIET is not set +# CONFIG_ZISOFS is not set +CONFIG_UDF_FS=m +CONFIG_UDF_NLS=y + +# +# DOS/FAT/NT Filesystems +# +CONFIG_FAT_FS=y +CONFIG_MSDOS_FS=y +CONFIG_VFAT_FS=y +CONFIG_FAT_DEFAULT_CODEPAGE=437 +CONFIG_FAT_DEFAULT_IOCHARSET="iso8859-1" +# CONFIG_NTFS_FS is not set + +# +# Pseudo filesystems +# +CONFIG_PROC_FS=y +CONFIG_PROC_SYSCTL=y +CONFIG_SYSFS=y +CONFIG_TMPFS=y +# CONFIG_TMPFS_POSIX_ACL is not set +# CONFIG_HUGETLB_PAGE is not set +# CONFIG_CONFIGFS_FS is not set + +# +# Miscellaneous filesystems +# +# CONFIG_ADFS_FS is not set +# CONFIG_AFFS_FS is not set +# CONFIG_HFS_FS is not set +# CONFIG_HFSPLUS_FS is not set +# CONFIG_BEFS_FS is not set +# CONFIG_BFS_FS is not set +# CONFIG_EFS_FS is not set +CONFIG_JFFS2_FS=y +CONFIG_JFFS2_FS_DEBUG=0 +CONFIG_JFFS2_FS_WRITEBUFFER=y +# CONFIG_JFFS2_FS_WBUF_VERIFY is not set +# CONFIG_JFFS2_SUMMARY is not set +# CONFIG_JFFS2_FS_XATTR is not set +# CONFIG_JFFS2_COMPRESSION_OPTIONS is not set +CONFIG_JFFS2_ZLIB=y +# CONFIG_JFFS2_LZO is not set +CONFIG_JFFS2_RTIME=y +# CONFIG_JFFS2_RUBIN is not set +CONFIG_CRAMFS=y +# CONFIG_VXFS_FS is not set +# CONFIG_MINIX_FS is not set +# CONFIG_HPFS_FS is not set +# CONFIG_QNX4FS_FS is not set +# CONFIG_ROMFS_FS is not set +# CONFIG_SYSV_FS is not set +# CONFIG_UFS_FS is not set +CONFIG_NETWORK_FILESYSTEMS=y +CONFIG_NFS_FS=y +CONFIG_NFS_V3=y +# CONFIG_NFS_V3_ACL is not set +# CONFIG_NFS_V4 is not set +# CONFIG_NFSD is not set +CONFIG_ROOT_NFS=y +CONFIG_LOCKD=y +CONFIG_LOCKD_V4=y +CONFIG_NFS_COMMON=y +CONFIG_SUNRPC=y +# CONFIG_SUNRPC_BIND34 is not set +# CONFIG_RPCSEC_GSS_KRB5 is not set +# CONFIG_RPCSEC_GSS_SPKM3 is not set +# CONFIG_SMB_FS is not set +# CONFIG_CIFS is not set +# CONFIG_NCP_FS is not set +# CONFIG_CODA_FS is not set +# CONFIG_AFS_FS is not set + +# +# Partition Types +# +CONFIG_PARTITION_ADVANCED=y +# CONFIG_ACORN_PARTITION is not set +# CONFIG_OSF_PARTITION is not set +# CONFIG_AMIGA_PARTITION is not set +# CONFIG_ATARI_PARTITION is not set +# CONFIG_MAC_PARTITION is not set +CONFIG_MSDOS_PARTITION=y +CONFIG_BSD_DISKLABEL=y +CONFIG_MINIX_SUBPARTITION=y +CONFIG_SOLARIS_X86_PARTITION=y +CONFIG_UNIXWARE_DISKLABEL=y +CONFIG_LDM_PARTITION=y +CONFIG_LDM_DEBUG=y +# CONFIG_SGI_PARTITION is not set +# CONFIG_ULTRIX_PARTITION is not set +CONFIG_SUN_PARTITION=y +# CONFIG_KARMA_PARTITION is not set +# CONFIG_EFI_PARTITION is not set +# CONFIG_SYSV68_PARTITION is not set +CONFIG_NLS=y +CONFIG_NLS_DEFAULT="iso8859-1" +CONFIG_NLS_CODEPAGE_437=y +# CONFIG_NLS_CODEPAGE_737 is not set +# CONFIG_NLS_CODEPAGE_775 is not set +CONFIG_NLS_CODEPAGE_850=y +# CONFIG_NLS_CODEPAGE_852 is not set +# CONFIG_NLS_CODEPAGE_855 is not set +# CONFIG_NLS_CODEPAGE_857 is not set +# CONFIG_NLS_CODEPAGE_860 is not set +# CONFIG_NLS_CODEPAGE_861 is not set +# CONFIG_NLS_CODEPAGE_862 is not set +# CONFIG_NLS_CODEPAGE_863 is not set +# CONFIG_NLS_CODEPAGE_864 is not set +# CONFIG_NLS_CODEPAGE_865 is not set +# CONFIG_NLS_CODEPAGE_866 is not set +# CONFIG_NLS_CODEPAGE_869 is not set +# CONFIG_NLS_CODEPAGE_936 is not set +# CONFIG_NLS_CODEPAGE_950 is not set +# CONFIG_NLS_CODEPAGE_932 is not set +# CONFIG_NLS_CODEPAGE_949 is not set +# CONFIG_NLS_CODEPAGE_874 is not set +# CONFIG_NLS_ISO8859_8 is not set +# CONFIG_NLS_CODEPAGE_1250 is not set +# CONFIG_NLS_CODEPAGE_1251 is not set +# CONFIG_NLS_ASCII is not set +CONFIG_NLS_ISO8859_1=y +CONFIG_NLS_ISO8859_2=y +# CONFIG_NLS_ISO8859_3 is not set +# CONFIG_NLS_ISO8859_4 is not set +# CONFIG_NLS_ISO8859_5 is not set +# CONFIG_NLS_ISO8859_6 is not set +# CONFIG_NLS_ISO8859_7 is not set +# CONFIG_NLS_ISO8859_9 is not set +# CONFIG_NLS_ISO8859_13 is not set +# CONFIG_NLS_ISO8859_14 is not set +# CONFIG_NLS_ISO8859_15 is not set +# CONFIG_NLS_KOI8_R is not set +# CONFIG_NLS_KOI8_U is not set +# CONFIG_NLS_UTF8 is not set +# CONFIG_DLM is not set + +# +# Kernel hacking +# +# CONFIG_PRINTK_TIME is not set +CONFIG_ENABLE_WARN_DEPRECATED=y +CONFIG_ENABLE_MUST_CHECK=y +CONFIG_FRAME_WARN=1024 +CONFIG_MAGIC_SYSRQ=y +# CONFIG_UNUSED_SYMBOLS is not set +# CONFIG_DEBUG_FS is not set +# CONFIG_HEADERS_CHECK is not set +# CONFIG_DEBUG_KERNEL is not set +# CONFIG_DEBUG_BUGVERBOSE is not set +CONFIG_FRAME_POINTER=y +# CONFIG_LATENCYTOP is not set +# CONFIG_SAMPLES is not set +CONFIG_DEBUG_USER=y + +# +# Security options +# +# CONFIG_KEYS is not set +# CONFIG_SECURITY is not set +# CONFIG_SECURITY_FILE_CAPABILITIES is not set +CONFIG_CRYPTO=y + +# +# Crypto core or helper +# +CONFIG_CRYPTO_ALGAPI=m +CONFIG_CRYPTO_BLKCIPHER=m +CONFIG_CRYPTO_MANAGER=m +# CONFIG_CRYPTO_GF128MUL is not set +# CONFIG_CRYPTO_NULL is not set +# CONFIG_CRYPTO_CRYPTD is not set +# CONFIG_CRYPTO_AUTHENC is not set +# CONFIG_CRYPTO_TEST is not set + +# +# Authenticated Encryption with Associated Data +# +# CONFIG_CRYPTO_CCM is not set +# CONFIG_CRYPTO_GCM is not set +# CONFIG_CRYPTO_SEQIV is not set + +# +# Block modes +# +CONFIG_CRYPTO_CBC=m +# CONFIG_CRYPTO_CTR is not set +# CONFIG_CRYPTO_CTS is not set +CONFIG_CRYPTO_ECB=m +# CONFIG_CRYPTO_LRW is not set +CONFIG_CRYPTO_PCBC=m +# CONFIG_CRYPTO_XTS is not set + +# +# Hash modes +# +# CONFIG_CRYPTO_HMAC is not set +# CONFIG_CRYPTO_XCBC is not set + +# +# Digest +# +# CONFIG_CRYPTO_CRC32C is not set +# CONFIG_CRYPTO_MD4 is not set +# CONFIG_CRYPTO_MD5 is not set +# CONFIG_CRYPTO_MICHAEL_MIC is not set +# CONFIG_CRYPTO_SHA1 is not set +# CONFIG_CRYPTO_SHA256 is not set +# CONFIG_CRYPTO_SHA512 is not set +# CONFIG_CRYPTO_TGR192 is not set +# CONFIG_CRYPTO_WP512 is not set + +# +# Ciphers +# +# CONFIG_CRYPTO_AES is not set +# CONFIG_CRYPTO_ANUBIS is not set +# CONFIG_CRYPTO_ARC4 is not set +# CONFIG_CRYPTO_BLOWFISH is not set +# CONFIG_CRYPTO_CAMELLIA is not set +# CONFIG_CRYPTO_CAST5 is not set +# CONFIG_CRYPTO_CAST6 is not set +# CONFIG_CRYPTO_DES is not set +# CONFIG_CRYPTO_FCRYPT is not set +# CONFIG_CRYPTO_KHAZAD is not set +# CONFIG_CRYPTO_SALSA20 is not set +# CONFIG_CRYPTO_SEED is not set +# CONFIG_CRYPTO_SERPENT is not set +# CONFIG_CRYPTO_TEA is not set +# CONFIG_CRYPTO_TWOFISH is not set + +# +# Compression +# +# CONFIG_CRYPTO_DEFLATE is not set +# CONFIG_CRYPTO_LZO is not set +CONFIG_CRYPTO_HW=y + +# +# Library routines +# +CONFIG_BITREVERSE=y +# CONFIG_GENERIC_FIND_FIRST_BIT is not set +# CONFIG_GENERIC_FIND_NEXT_BIT is not set +CONFIG_CRC_CCITT=y +CONFIG_CRC16=y +CONFIG_CRC_ITU_T=m +CONFIG_CRC32=y +# CONFIG_CRC7 is not set +CONFIG_LIBCRC32C=y +CONFIG_ZLIB_INFLATE=y +CONFIG_ZLIB_DEFLATE=y +CONFIG_PLIST=y +CONFIG_HAS_IOMEM=y +CONFIG_HAS_IOPORT=y +CONFIG_HAS_DMA=y diff --git a/arch/arm/configs/lpd270_defconfig b/arch/arm/configs/lpd270_defconfig index a3bf5833b87..1a38d8e3fe6 100644 --- a/arch/arm/configs/lpd270_defconfig +++ b/arch/arm/configs/lpd270_defconfig @@ -173,7 +173,6 @@ CONFIG_XSCALE_PMU=y # Kernel Features # # CONFIG_PREEMPT is not set -# CONFIG_NO_IDLE_HZ is not set CONFIG_HZ=100 # CONFIG_AEABI is not set # CONFIG_ARCH_DISCONTIGMEM_ENABLE is not set diff --git a/arch/arm/configs/lpd7a404_defconfig b/arch/arm/configs/lpd7a404_defconfig index 46a0f7fe1fa..7a2e932da1c 100644 --- a/arch/arm/configs/lpd7a404_defconfig +++ b/arch/arm/configs/lpd7a404_defconfig @@ -148,7 +148,6 @@ CONFIG_ARM_AMBA=y # Kernel Features # CONFIG_PREEMPT=y -# CONFIG_NO_IDLE_HZ is not set # CONFIG_AEABI is not set CONFIG_ARCH_DISCONTIGMEM_ENABLE=y CONFIG_SELECT_MEMORY_MODEL=y diff --git a/arch/arm/configs/mv78xx0_defconfig b/arch/arm/configs/mv78xx0_defconfig new file mode 100644 index 00000000000..d38ebf8721a --- /dev/null +++ b/arch/arm/configs/mv78xx0_defconfig @@ -0,0 +1,1445 @@ +# +# Automatically generated make config: don't edit +# Linux kernel version: 2.6.26-rc5 +# Fri Jun 13 02:57:32 2008 +# +CONFIG_ARM=y +CONFIG_SYS_SUPPORTS_APM_EMULATION=y +# CONFIG_GENERIC_GPIO is not set +CONFIG_GENERIC_TIME=y +CONFIG_GENERIC_CLOCKEVENTS=y +CONFIG_MMU=y +# CONFIG_NO_IOPORT is not set +CONFIG_GENERIC_HARDIRQS=y +CONFIG_STACKTRACE_SUPPORT=y +CONFIG_HAVE_LATENCYTOP_SUPPORT=y +CONFIG_LOCKDEP_SUPPORT=y +CONFIG_TRACE_IRQFLAGS_SUPPORT=y +CONFIG_HARDIRQS_SW_RESEND=y +CONFIG_GENERIC_IRQ_PROBE=y +CONFIG_RWSEM_GENERIC_SPINLOCK=y +# CONFIG_ARCH_HAS_ILOG2_U32 is not set +# CONFIG_ARCH_HAS_ILOG2_U64 is not set +CONFIG_GENERIC_HWEIGHT=y +CONFIG_GENERIC_CALIBRATE_DELAY=y +CONFIG_ARCH_SUPPORTS_AOUT=y +CONFIG_ZONE_DMA=y +CONFIG_VECTORS_BASE=0xffff0000 +CONFIG_DEFCONFIG_LIST="/lib/modules/$UNAME_RELEASE/.config" + +# +# General setup +# +CONFIG_EXPERIMENTAL=y +CONFIG_BROKEN_ON_SMP=y +CONFIG_LOCK_KERNEL=y +CONFIG_INIT_ENV_ARG_LIMIT=32 +CONFIG_LOCALVERSION="" +CONFIG_LOCALVERSION_AUTO=y +CONFIG_SWAP=y +CONFIG_SYSVIPC=y +CONFIG_SYSVIPC_SYSCTL=y +# CONFIG_POSIX_MQUEUE is not set +# CONFIG_BSD_PROCESS_ACCT is not set +# CONFIG_TASKSTATS is not set +# CONFIG_AUDIT is not set +# CONFIG_IKCONFIG is not set +CONFIG_LOG_BUF_SHIFT=14 +# CONFIG_CGROUPS is not set +# CONFIG_GROUP_SCHED is not set +CONFIG_SYSFS_DEPRECATED=y +CONFIG_SYSFS_DEPRECATED_V2=y +# CONFIG_RELAY is not set +# CONFIG_NAMESPACES is not set +# CONFIG_BLK_DEV_INITRD is not set +CONFIG_CC_OPTIMIZE_FOR_SIZE=y +CONFIG_SYSCTL=y +CONFIG_EMBEDDED=y +CONFIG_UID16=y +CONFIG_SYSCTL_SYSCALL=y +CONFIG_SYSCTL_SYSCALL_CHECK=y +CONFIG_KALLSYMS=y +CONFIG_KALLSYMS_ALL=y +# CONFIG_KALLSYMS_EXTRA_PASS is not set +CONFIG_HOTPLUG=y +CONFIG_PRINTK=y +CONFIG_BUG=y +CONFIG_ELF_CORE=y +CONFIG_COMPAT_BRK=y +CONFIG_BASE_FULL=y +CONFIG_FUTEX=y +CONFIG_ANON_INODES=y +CONFIG_EPOLL=y +CONFIG_SIGNALFD=y +CONFIG_TIMERFD=y +CONFIG_EVENTFD=y +CONFIG_SHMEM=y +CONFIG_VM_EVENT_COUNTERS=y +# CONFIG_SLUB_DEBUG is not set +# CONFIG_SLAB is not set +CONFIG_SLUB=y +# CONFIG_SLOB is not set +CONFIG_PROFILING=y +# CONFIG_MARKERS is not set +CONFIG_OPROFILE=y +CONFIG_HAVE_OPROFILE=y +CONFIG_KPROBES=y +CONFIG_KRETPROBES=y +CONFIG_HAVE_KPROBES=y +CONFIG_HAVE_KRETPROBES=y +# CONFIG_HAVE_DMA_ATTRS is not set +CONFIG_PROC_PAGE_MONITOR=y +CONFIG_RT_MUTEXES=y +# CONFIG_TINY_SHMEM is not set +CONFIG_BASE_SMALL=0 +CONFIG_MODULES=y +# CONFIG_MODULE_FORCE_LOAD is not set +CONFIG_MODULE_UNLOAD=y +# CONFIG_MODULE_FORCE_UNLOAD is not set +# CONFIG_MODVERSIONS is not set +# CONFIG_MODULE_SRCVERSION_ALL is not set +# CONFIG_KMOD is not set +CONFIG_BLOCK=y +# CONFIG_LBD is not set +# CONFIG_BLK_DEV_IO_TRACE is not set +# CONFIG_LSF is not set +# CONFIG_BLK_DEV_BSG is not set + +# +# IO Schedulers +# +CONFIG_IOSCHED_NOOP=y +CONFIG_IOSCHED_AS=y +CONFIG_IOSCHED_DEADLINE=y +CONFIG_IOSCHED_CFQ=y +# CONFIG_DEFAULT_AS is not set +# CONFIG_DEFAULT_DEADLINE is not set +CONFIG_DEFAULT_CFQ=y +# CONFIG_DEFAULT_NOOP is not set +CONFIG_DEFAULT_IOSCHED="cfq" +CONFIG_CLASSIC_RCU=y + +# +# System Type +# +# CONFIG_ARCH_AAEC2000 is not set +# CONFIG_ARCH_INTEGRATOR is not set +# CONFIG_ARCH_REALVIEW is not set +# CONFIG_ARCH_VERSATILE is not set +# CONFIG_ARCH_AT91 is not set +# CONFIG_ARCH_CLPS7500 is not set +# CONFIG_ARCH_CLPS711X is not set +# CONFIG_ARCH_CO285 is not set +# CONFIG_ARCH_EBSA110 is not set +# CONFIG_ARCH_EP93XX is not set +# CONFIG_ARCH_FOOTBRIDGE is not set +# CONFIG_ARCH_NETX is not set +# CONFIG_ARCH_H720X is not set +# CONFIG_ARCH_IMX is not set +# CONFIG_ARCH_IOP13XX is not set +# CONFIG_ARCH_IOP32X is not set +# CONFIG_ARCH_IOP33X is not set +# CONFIG_ARCH_IXP23XX is not set +# CONFIG_ARCH_IXP2000 is not set +# CONFIG_ARCH_IXP4XX is not set +# CONFIG_ARCH_L7200 is not set +# CONFIG_ARCH_KIRKWOOD is not set +# CONFIG_ARCH_KS8695 is not set +# CONFIG_ARCH_NS9XXX is not set +# CONFIG_ARCH_LOKI is not set +CONFIG_ARCH_MV78XX0=y +# CONFIG_ARCH_MXC is not set +# CONFIG_ARCH_ORION5X is not set +# CONFIG_ARCH_PNX4008 is not set +# CONFIG_ARCH_PXA is not set +# CONFIG_ARCH_RPC is not set +# CONFIG_ARCH_SA1100 is not set +# CONFIG_ARCH_S3C2410 is not set +# CONFIG_ARCH_SHARK is not set +# CONFIG_ARCH_LH7A40X is not set +# CONFIG_ARCH_DAVINCI is not set +# CONFIG_ARCH_OMAP is not set +# CONFIG_ARCH_MSM7X00A is not set + +# +# Marvell MV78xx0 Implementations +# +CONFIG_MACH_DB78X00_BP=y + +# +# Boot options +# + +# +# Power management +# +CONFIG_PLAT_ORION=y + +# +# Processor Type +# +CONFIG_CPU_32=y +CONFIG_CPU_FEROCEON=y +CONFIG_CPU_FEROCEON_OLD_ID=y +CONFIG_CPU_32v5=y +CONFIG_CPU_ABRT_EV5T=y +CONFIG_CPU_PABRT_NOIFAR=y +CONFIG_CPU_CACHE_VIVT=y +CONFIG_CPU_COPY_FEROCEON=y +CONFIG_CPU_TLB_FEROCEON=y +CONFIG_CPU_CP15=y +CONFIG_CPU_CP15_MMU=y + +# +# Processor Features +# +CONFIG_ARM_THUMB=y +# CONFIG_CPU_ICACHE_DISABLE is not set +# CONFIG_CPU_DCACHE_DISABLE is not set +CONFIG_OUTER_CACHE=y +CONFIG_CACHE_FEROCEON_L2=y + +# +# Bus support +# +CONFIG_PCI=y +CONFIG_PCI_SYSCALL=y +# CONFIG_ARCH_SUPPORTS_MSI is not set +CONFIG_PCI_LEGACY=y +# CONFIG_PCI_DEBUG is not set +# CONFIG_PCCARD is not set + +# +# Kernel Features +# +CONFIG_TICK_ONESHOT=y +CONFIG_NO_HZ=y +CONFIG_HIGH_RES_TIMERS=y +CONFIG_GENERIC_CLOCKEVENTS_BUILD=y +CONFIG_PREEMPT=y +CONFIG_HZ=100 +CONFIG_AEABI=y +CONFIG_OABI_COMPAT=y +# CONFIG_ARCH_DISCONTIGMEM_ENABLE is not set +CONFIG_SELECT_MEMORY_MODEL=y +CONFIG_FLATMEM_MANUAL=y +# CONFIG_DISCONTIGMEM_MANUAL is not set +# CONFIG_SPARSEMEM_MANUAL is not set +CONFIG_FLATMEM=y +CONFIG_FLAT_NODE_MEM_MAP=y +# CONFIG_SPARSEMEM_STATIC is not set +# CONFIG_SPARSEMEM_VMEMMAP_ENABLE is not set +CONFIG_PAGEFLAGS_EXTENDED=y +CONFIG_SPLIT_PTLOCK_CPUS=4096 +# CONFIG_RESOURCES_64BIT is not set +CONFIG_ZONE_DMA_FLAG=1 +CONFIG_BOUNCE=y +CONFIG_VIRT_TO_BUS=y +CONFIG_ALIGNMENT_TRAP=y + +# +# Boot options +# +CONFIG_ZBOOT_ROM_TEXT=0x0 +CONFIG_ZBOOT_ROM_BSS=0x0 +CONFIG_CMDLINE="" +# CONFIG_XIP_KERNEL is not set +# CONFIG_KEXEC is not set + +# +# Floating point emulation +# + +# +# At least one emulation must be selected +# +CONFIG_FPE_NWFPE=y +# CONFIG_FPE_NWFPE_XP is not set +# CONFIG_FPE_FASTFPE is not set +CONFIG_VFP=y + +# +# Userspace binary formats +# +CONFIG_BINFMT_ELF=y +# CONFIG_BINFMT_AOUT is not set +# CONFIG_BINFMT_MISC is not set + +# +# Power management options +# +# CONFIG_PM is not set +CONFIG_ARCH_SUSPEND_POSSIBLE=y + +# +# Networking +# +CONFIG_NET=y + +# +# Networking options +# +CONFIG_PACKET=y +CONFIG_PACKET_MMAP=y +CONFIG_UNIX=y +CONFIG_XFRM=y +# CONFIG_XFRM_USER is not set +# CONFIG_XFRM_SUB_POLICY is not set +# CONFIG_XFRM_MIGRATE is not set +# CONFIG_XFRM_STATISTICS is not set +# CONFIG_NET_KEY is not set +CONFIG_INET=y +CONFIG_IP_MULTICAST=y +# CONFIG_IP_ADVANCED_ROUTER is not set +CONFIG_IP_FIB_HASH=y +CONFIG_IP_PNP=y +CONFIG_IP_PNP_DHCP=y +CONFIG_IP_PNP_BOOTP=y +# CONFIG_IP_PNP_RARP is not set +# CONFIG_NET_IPIP is not set +# CONFIG_NET_IPGRE is not set +# CONFIG_IP_MROUTE is not set +# CONFIG_ARPD is not set +# CONFIG_SYN_COOKIES is not set +# CONFIG_INET_AH is not set +# CONFIG_INET_ESP is not set +# CONFIG_INET_IPCOMP is not set +# CONFIG_INET_XFRM_TUNNEL is not set +# CONFIG_INET_TUNNEL is not set +CONFIG_INET_XFRM_MODE_TRANSPORT=y +CONFIG_INET_XFRM_MODE_TUNNEL=y +CONFIG_INET_XFRM_MODE_BEET=y +# CONFIG_INET_LRO is not set +CONFIG_INET_DIAG=y +CONFIG_INET_TCP_DIAG=y +# CONFIG_TCP_CONG_ADVANCED is not set +CONFIG_TCP_CONG_CUBIC=y +CONFIG_DEFAULT_TCP_CONG="cubic" +# CONFIG_TCP_MD5SIG is not set +# CONFIG_IPV6 is not set +# CONFIG_NETWORK_SECMARK is not set +# CONFIG_NETFILTER is not set +# CONFIG_IP_DCCP is not set +# CONFIG_IP_SCTP is not set +# CONFIG_TIPC is not set +# CONFIG_ATM is not set +# CONFIG_BRIDGE is not set +# CONFIG_VLAN_8021Q is not set +# CONFIG_DECNET is not set +# CONFIG_LLC2 is not set +# CONFIG_IPX is not set +# CONFIG_ATALK is not set +# CONFIG_X25 is not set +# CONFIG_LAPB is not set +# CONFIG_ECONET is not set +# CONFIG_WAN_ROUTER is not set +# CONFIG_NET_SCHED is not set + +# +# Network testing +# +CONFIG_NET_PKTGEN=m +# CONFIG_NET_TCPPROBE is not set +# CONFIG_HAMRADIO is not set +# CONFIG_CAN is not set +# CONFIG_IRDA is not set +# CONFIG_BT is not set +# CONFIG_AF_RXRPC is not set + +# +# Wireless +# +# CONFIG_CFG80211 is not set +CONFIG_WIRELESS_EXT=y +# CONFIG_MAC80211 is not set +# CONFIG_IEEE80211 is not set +# CONFIG_RFKILL is not set +# CONFIG_NET_9P is not set + +# +# Device Drivers +# + +# +# Generic Driver Options +# +CONFIG_UEVENT_HELPER_PATH="/sbin/hotplug" +CONFIG_STANDALONE=y +CONFIG_PREVENT_FIRMWARE_BUILD=y +CONFIG_FW_LOADER=y +# CONFIG_DEBUG_DRIVER is not set +# CONFIG_DEBUG_DEVRES is not set +# CONFIG_SYS_HYPERVISOR is not set +# CONFIG_CONNECTOR is not set +CONFIG_MTD=y +# CONFIG_MTD_DEBUG is not set +# CONFIG_MTD_CONCAT is not set +CONFIG_MTD_PARTITIONS=y +# CONFIG_MTD_REDBOOT_PARTS is not set +CONFIG_MTD_CMDLINE_PARTS=y +# CONFIG_MTD_AFS_PARTS is not set +# CONFIG_MTD_AR7_PARTS is not set + +# +# User Modules And Translation Layers +# +CONFIG_MTD_CHAR=y +CONFIG_MTD_BLKDEVS=y +CONFIG_MTD_BLOCK=y +# CONFIG_FTL is not set +# CONFIG_NFTL is not set +# CONFIG_INFTL is not set +# CONFIG_RFD_FTL is not set +# CONFIG_SSFDC is not set +# CONFIG_MTD_OOPS is not set + +# +# RAM/ROM/Flash chip drivers +# +CONFIG_MTD_CFI=y +CONFIG_MTD_JEDECPROBE=y +CONFIG_MTD_GEN_PROBE=y +CONFIG_MTD_CFI_ADV_OPTIONS=y +CONFIG_MTD_CFI_NOSWAP=y +# CONFIG_MTD_CFI_BE_BYTE_SWAP is not set +# CONFIG_MTD_CFI_LE_BYTE_SWAP is not set +CONFIG_MTD_CFI_GEOMETRY=y +CONFIG_MTD_MAP_BANK_WIDTH_1=y +CONFIG_MTD_MAP_BANK_WIDTH_2=y +CONFIG_MTD_MAP_BANK_WIDTH_4=y +# CONFIG_MTD_MAP_BANK_WIDTH_8 is not set +# CONFIG_MTD_MAP_BANK_WIDTH_16 is not set +# CONFIG_MTD_MAP_BANK_WIDTH_32 is not set +CONFIG_MTD_CFI_I1=y +CONFIG_MTD_CFI_I2=y +# CONFIG_MTD_CFI_I4 is not set +# CONFIG_MTD_CFI_I8 is not set +# CONFIG_MTD_OTP is not set +CONFIG_MTD_CFI_INTELEXT=y +CONFIG_MTD_CFI_AMDSTD=y +# CONFIG_MTD_CFI_STAA is not set +CONFIG_MTD_CFI_UTIL=y +# CONFIG_MTD_RAM is not set +# CONFIG_MTD_ROM is not set +# CONFIG_MTD_ABSENT is not set + +# +# Mapping drivers for chip access +# +# CONFIG_MTD_COMPLEX_MAPPINGS is not set +CONFIG_MTD_PHYSMAP=y +CONFIG_MTD_PHYSMAP_START=0x0 +CONFIG_MTD_PHYSMAP_LEN=0x0 +CONFIG_MTD_PHYSMAP_BANKWIDTH=0 +# CONFIG_MTD_ARM_INTEGRATOR is not set +# CONFIG_MTD_IMPA7 is not set +# CONFIG_MTD_INTEL_VR_NOR is not set +# CONFIG_MTD_PLATRAM is not set + +# +# Self-contained MTD device drivers +# +# CONFIG_MTD_PMC551 is not set +# CONFIG_MTD_SLRAM is not set +# CONFIG_MTD_PHRAM is not set +# CONFIG_MTD_MTDRAM is not set +# CONFIG_MTD_BLOCK2MTD is not set + +# +# Disk-On-Chip Device Drivers +# +# CONFIG_MTD_DOC2000 is not set +# CONFIG_MTD_DOC2001 is not set +# CONFIG_MTD_DOC2001PLUS is not set +CONFIG_MTD_NAND=y +CONFIG_MTD_NAND_VERIFY_WRITE=y +# CONFIG_MTD_NAND_ECC_SMC is not set +# CONFIG_MTD_NAND_MUSEUM_IDS is not set +CONFIG_MTD_NAND_IDS=y +# CONFIG_MTD_NAND_DISKONCHIP is not set +# CONFIG_MTD_NAND_CAFE is not set +# CONFIG_MTD_NAND_NANDSIM is not set +# CONFIG_MTD_NAND_PLATFORM is not set +# CONFIG_MTD_ALAUDA is not set +CONFIG_MTD_NAND_ORION=y +# CONFIG_MTD_ONENAND is not set + +# +# UBI - Unsorted block images +# +# CONFIG_MTD_UBI is not set +# CONFIG_PARPORT is not set +CONFIG_BLK_DEV=y +# CONFIG_BLK_CPQ_DA is not set +# CONFIG_BLK_CPQ_CISS_DA is not set +# CONFIG_BLK_DEV_DAC960 is not set +# CONFIG_BLK_DEV_UMEM is not set +# CONFIG_BLK_DEV_COW_COMMON is not set +CONFIG_BLK_DEV_LOOP=y +# CONFIG_BLK_DEV_CRYPTOLOOP is not set +# CONFIG_BLK_DEV_NBD is not set +# CONFIG_BLK_DEV_SX8 is not set +# CONFIG_BLK_DEV_UB is not set +# CONFIG_BLK_DEV_RAM is not set +# CONFIG_CDROM_PKTCDVD is not set +# CONFIG_ATA_OVER_ETH is not set +CONFIG_MISC_DEVICES=y +# CONFIG_PHANTOM is not set +# CONFIG_EEPROM_93CX6 is not set +# CONFIG_SGI_IOC4 is not set +# CONFIG_TIFM_CORE is not set +# CONFIG_ENCLOSURE_SERVICES is not set +CONFIG_HAVE_IDE=y +# CONFIG_IDE is not set + +# +# SCSI device support +# +# CONFIG_RAID_ATTRS is not set +CONFIG_SCSI=y +CONFIG_SCSI_DMA=y +# CONFIG_SCSI_TGT is not set +# CONFIG_SCSI_NETLINK is not set +# CONFIG_SCSI_PROC_FS is not set + +# +# SCSI support type (disk, tape, CD-ROM) +# +CONFIG_BLK_DEV_SD=y +# CONFIG_CHR_DEV_ST is not set +# CONFIG_CHR_DEV_OSST is not set +CONFIG_BLK_DEV_SR=m +# CONFIG_BLK_DEV_SR_VENDOR is not set +CONFIG_CHR_DEV_SG=m +# CONFIG_CHR_DEV_SCH is not set + +# +# Some SCSI devices (e.g. CD jukebox) support multiple LUNs +# +# CONFIG_SCSI_MULTI_LUN is not set +# CONFIG_SCSI_CONSTANTS is not set +# CONFIG_SCSI_LOGGING is not set +# CONFIG_SCSI_SCAN_ASYNC is not set +CONFIG_SCSI_WAIT_SCAN=m + +# +# SCSI Transports +# +# CONFIG_SCSI_SPI_ATTRS is not set +# CONFIG_SCSI_FC_ATTRS is not set +# CONFIG_SCSI_ISCSI_ATTRS is not set +# CONFIG_SCSI_SAS_LIBSAS is not set +# CONFIG_SCSI_SRP_ATTRS is not set +CONFIG_SCSI_LOWLEVEL=y +# CONFIG_ISCSI_TCP is not set +# CONFIG_BLK_DEV_3W_XXXX_RAID is not set +# CONFIG_SCSI_3W_9XXX is not set +# CONFIG_SCSI_ACARD is not set +# CONFIG_SCSI_AACRAID is not set +# CONFIG_SCSI_AIC7XXX is not set +# CONFIG_SCSI_AIC7XXX_OLD is not set +# CONFIG_SCSI_AIC79XX is not set +# CONFIG_SCSI_AIC94XX is not set +# CONFIG_SCSI_DPT_I2O is not set +# CONFIG_SCSI_ADVANSYS is not set +# CONFIG_SCSI_ARCMSR is not set +# CONFIG_MEGARAID_NEWGEN is not set +# CONFIG_MEGARAID_LEGACY is not set +# CONFIG_MEGARAID_SAS is not set +# CONFIG_SCSI_HPTIOP is not set +# CONFIG_SCSI_DMX3191D is not set +# CONFIG_SCSI_FUTURE_DOMAIN is not set +# CONFIG_SCSI_IPS is not set +# CONFIG_SCSI_INITIO is not set +# CONFIG_SCSI_INIA100 is not set +# CONFIG_SCSI_MVSAS is not set +# CONFIG_SCSI_STEX is not set +# CONFIG_SCSI_SYM53C8XX_2 is not set +# CONFIG_SCSI_IPR is not set +# CONFIG_SCSI_QLOGIC_1280 is not set +# CONFIG_SCSI_QLA_FC is not set +# CONFIG_SCSI_QLA_ISCSI is not set +# CONFIG_SCSI_LPFC is not set +# CONFIG_SCSI_DC395x is not set +# CONFIG_SCSI_DC390T is not set +# CONFIG_SCSI_NSP32 is not set +# CONFIG_SCSI_DEBUG is not set +# CONFIG_SCSI_SRP is not set +CONFIG_ATA=y +# CONFIG_ATA_NONSTANDARD is not set +CONFIG_SATA_PMP=y +# CONFIG_SATA_AHCI is not set +# CONFIG_SATA_SIL24 is not set +CONFIG_ATA_SFF=y +# CONFIG_SATA_SVW is not set +# CONFIG_ATA_PIIX is not set +CONFIG_SATA_MV=y +# CONFIG_SATA_NV is not set +# CONFIG_PDC_ADMA is not set +# CONFIG_SATA_QSTOR is not set +# CONFIG_SATA_PROMISE is not set +# CONFIG_SATA_SX4 is not set +# CONFIG_SATA_SIL is not set +# CONFIG_SATA_SIS is not set +# CONFIG_SATA_ULI is not set +# CONFIG_SATA_VIA is not set +# CONFIG_SATA_VITESSE is not set +# CONFIG_SATA_INIC162X is not set +# CONFIG_PATA_ALI is not set +# CONFIG_PATA_AMD is not set +# CONFIG_PATA_ARTOP is not set +# CONFIG_PATA_ATIIXP is not set +# CONFIG_PATA_CMD640_PCI is not set +# CONFIG_PATA_CMD64X is not set +# CONFIG_PATA_CS5520 is not set +# CONFIG_PATA_CS5530 is not set +# CONFIG_PATA_CYPRESS is not set +# CONFIG_PATA_EFAR is not set +# CONFIG_ATA_GENERIC is not set +# CONFIG_PATA_HPT366 is not set +# CONFIG_PATA_HPT37X is not set +# CONFIG_PATA_HPT3X2N is not set +# CONFIG_PATA_HPT3X3 is not set +# CONFIG_PATA_IT821X is not set +# CONFIG_PATA_IT8213 is not set +# CONFIG_PATA_JMICRON is not set +# CONFIG_PATA_TRIFLEX is not set +# CONFIG_PATA_MARVELL is not set +# CONFIG_PATA_MPIIX is not set +# CONFIG_PATA_OLDPIIX is not set +# CONFIG_PATA_NETCELL is not set +# CONFIG_PATA_NINJA32 is not set +# CONFIG_PATA_NS87410 is not set +# CONFIG_PATA_NS87415 is not set +# CONFIG_PATA_OPTI is not set +# CONFIG_PATA_OPTIDMA is not set +# CONFIG_PATA_PDC_OLD is not set +# CONFIG_PATA_RADISYS is not set +# CONFIG_PATA_RZ1000 is not set +# CONFIG_PATA_SC1200 is not set +# CONFIG_PATA_SERVERWORKS is not set +# CONFIG_PATA_PDC2027X is not set +# CONFIG_PATA_SIL680 is not set +# CONFIG_PATA_SIS is not set +# CONFIG_PATA_VIA is not set +# CONFIG_PATA_WINBOND is not set +# CONFIG_PATA_PLATFORM is not set +# CONFIG_PATA_SCH is not set +# CONFIG_MD is not set +# CONFIG_FUSION is not set + +# +# IEEE 1394 (FireWire) support +# +# CONFIG_FIREWIRE is not set +# CONFIG_IEEE1394 is not set +# CONFIG_I2O is not set +CONFIG_NETDEVICES=y +# CONFIG_NETDEVICES_MULTIQUEUE is not set +# CONFIG_DUMMY is not set +# CONFIG_BONDING is not set +# CONFIG_MACVLAN is not set +# CONFIG_EQUALIZER is not set +# CONFIG_TUN is not set +# CONFIG_VETH is not set +# CONFIG_ARCNET is not set +# CONFIG_PHYLIB is not set +CONFIG_NET_ETHERNET=y +CONFIG_MII=y +# CONFIG_AX88796 is not set +# CONFIG_HAPPYMEAL is not set +# CONFIG_SUNGEM is not set +# CONFIG_CASSINI is not set +# CONFIG_NET_VENDOR_3COM is not set +# CONFIG_SMC91X is not set +# CONFIG_DM9000 is not set +# CONFIG_NET_TULIP is not set +# CONFIG_HP100 is not set +# CONFIG_IBM_NEW_EMAC_ZMII is not set +# CONFIG_IBM_NEW_EMAC_RGMII is not set +# CONFIG_IBM_NEW_EMAC_TAH is not set +# CONFIG_IBM_NEW_EMAC_EMAC4 is not set +CONFIG_NET_PCI=y +# CONFIG_PCNET32 is not set +# CONFIG_AMD8111_ETH is not set +# CONFIG_ADAPTEC_STARFIRE is not set +# CONFIG_B44 is not set +# CONFIG_FORCEDETH is not set +# CONFIG_EEPRO100 is not set +# CONFIG_E100 is not set +# CONFIG_FEALNX is not set +# CONFIG_NATSEMI is not set +# CONFIG_NE2K_PCI is not set +# CONFIG_8139CP is not set +# CONFIG_8139TOO is not set +# CONFIG_R6040 is not set +# CONFIG_SIS900 is not set +# CONFIG_EPIC100 is not set +# CONFIG_SUNDANCE is not set +# CONFIG_TLAN is not set +# CONFIG_VIA_RHINE is not set +# CONFIG_SC92031 is not set +CONFIG_NETDEV_1000=y +# CONFIG_ACENIC is not set +# CONFIG_DL2K is not set +# CONFIG_E1000 is not set +# CONFIG_E1000E is not set +# CONFIG_E1000E_ENABLED is not set +# CONFIG_IP1000 is not set +# CONFIG_IGB is not set +# CONFIG_NS83820 is not set +# CONFIG_HAMACHI is not set +# CONFIG_YELLOWFIN is not set +# CONFIG_R8169 is not set +# CONFIG_SIS190 is not set +# CONFIG_SKGE is not set +# CONFIG_SKY2 is not set +# CONFIG_VIA_VELOCITY is not set +# CONFIG_TIGON3 is not set +# CONFIG_BNX2 is not set +CONFIG_MV643XX_ETH=y +# CONFIG_QLA3XXX is not set +# CONFIG_ATL1 is not set +# CONFIG_NETDEV_10000 is not set +# CONFIG_TR is not set + +# +# Wireless LAN +# +# CONFIG_WLAN_PRE80211 is not set +# CONFIG_WLAN_80211 is not set +# CONFIG_IWLWIFI_LEDS is not set + +# +# USB Network Adapters +# +# CONFIG_USB_CATC is not set +# CONFIG_USB_KAWETH is not set +# CONFIG_USB_PEGASUS is not set +# CONFIG_USB_RTL8150 is not set +# CONFIG_USB_USBNET is not set +# CONFIG_WAN is not set +# CONFIG_FDDI is not set +# CONFIG_HIPPI is not set +# CONFIG_PPP is not set +# CONFIG_SLIP is not set +# CONFIG_NET_FC is not set +# CONFIG_NETCONSOLE is not set +# CONFIG_NETPOLL is not set +# CONFIG_NET_POLL_CONTROLLER is not set +# CONFIG_ISDN is not set + +# +# Input device support +# +CONFIG_INPUT=y +# CONFIG_INPUT_FF_MEMLESS is not set +# CONFIG_INPUT_POLLDEV is not set + +# +# Userland interfaces +# +# CONFIG_INPUT_MOUSEDEV is not set +# CONFIG_INPUT_JOYDEV is not set +CONFIG_INPUT_EVDEV=y +# CONFIG_INPUT_EVBUG is not set + +# +# Input Device Drivers +# +# CONFIG_INPUT_KEYBOARD is not set +# CONFIG_INPUT_MOUSE is not set +# CONFIG_INPUT_JOYSTICK is not set +# CONFIG_INPUT_TABLET is not set +# CONFIG_INPUT_TOUCHSCREEN is not set +# CONFIG_INPUT_MISC is not set + +# +# Hardware I/O ports +# +# CONFIG_SERIO is not set +# CONFIG_GAMEPORT is not set + +# +# Character devices +# +# CONFIG_VT is not set +CONFIG_DEVKMEM=y +# CONFIG_SERIAL_NONSTANDARD is not set +# CONFIG_NOZOMI is not set + +# +# Serial drivers +# +CONFIG_SERIAL_8250=y +CONFIG_SERIAL_8250_CONSOLE=y +# CONFIG_SERIAL_8250_PCI is not set +CONFIG_SERIAL_8250_NR_UARTS=4 +CONFIG_SERIAL_8250_RUNTIME_UARTS=2 +# CONFIG_SERIAL_8250_EXTENDED is not set + +# +# Non-8250 serial port support +# +CONFIG_SERIAL_CORE=y +CONFIG_SERIAL_CORE_CONSOLE=y +# CONFIG_SERIAL_JSM is not set +CONFIG_UNIX98_PTYS=y +CONFIG_LEGACY_PTYS=y +CONFIG_LEGACY_PTY_COUNT=16 +# CONFIG_IPMI_HANDLER is not set +# CONFIG_HW_RANDOM is not set +# CONFIG_NVRAM is not set +# CONFIG_R3964 is not set +# CONFIG_APPLICOM is not set +# CONFIG_RAW_DRIVER is not set +# CONFIG_TCG_TPM is not set +CONFIG_DEVPORT=y +CONFIG_I2C=y +CONFIG_I2C_BOARDINFO=y +CONFIG_I2C_CHARDEV=y + +# +# I2C Hardware Bus support +# +# CONFIG_I2C_ALI1535 is not set +# CONFIG_I2C_ALI1563 is not set +# CONFIG_I2C_ALI15X3 is not set +# CONFIG_I2C_AMD756 is not set +# CONFIG_I2C_AMD8111 is not set +# CONFIG_I2C_I801 is not set +# CONFIG_I2C_I810 is not set +# CONFIG_I2C_PIIX4 is not set +# CONFIG_I2C_NFORCE2 is not set +# CONFIG_I2C_OCORES is not set +# CONFIG_I2C_PARPORT_LIGHT is not set +# CONFIG_I2C_PROSAVAGE is not set +# CONFIG_I2C_SAVAGE4 is not set +# CONFIG_I2C_SIMTEC is not set +# CONFIG_I2C_SIS5595 is not set +# CONFIG_I2C_SIS630 is not set +# CONFIG_I2C_SIS96X is not set +# CONFIG_I2C_TAOS_EVM is not set +# CONFIG_I2C_STUB is not set +# CONFIG_I2C_TINY_USB is not set +# CONFIG_I2C_VIA is not set +# CONFIG_I2C_VIAPRO is not set +# CONFIG_I2C_VOODOO3 is not set +# CONFIG_I2C_PCA_PLATFORM is not set +CONFIG_I2C_MV64XXX=y + +# +# Miscellaneous I2C Chip support +# +# CONFIG_DS1682 is not set +# CONFIG_SENSORS_EEPROM is not set +# CONFIG_SENSORS_PCF8574 is not set +# CONFIG_PCF8575 is not set +# CONFIG_SENSORS_PCF8591 is not set +# CONFIG_SENSORS_MAX6875 is not set +# CONFIG_SENSORS_TSL2550 is not set +# CONFIG_I2C_DEBUG_CORE is not set +# CONFIG_I2C_DEBUG_ALGO is not set +# CONFIG_I2C_DEBUG_BUS is not set +# CONFIG_I2C_DEBUG_CHIP is not set +# CONFIG_SPI is not set +# CONFIG_W1 is not set +# CONFIG_POWER_SUPPLY is not set +CONFIG_HWMON=y +# CONFIG_HWMON_VID is not set +# CONFIG_SENSORS_AD7418 is not set +# CONFIG_SENSORS_ADM1021 is not set +# CONFIG_SENSORS_ADM1025 is not set +# CONFIG_SENSORS_ADM1026 is not set +# CONFIG_SENSORS_ADM1029 is not set +# CONFIG_SENSORS_ADM1031 is not set +# CONFIG_SENSORS_ADM9240 is not set +# CONFIG_SENSORS_ADT7470 is not set +# CONFIG_SENSORS_ADT7473 is not set +# CONFIG_SENSORS_ATXP1 is not set +# CONFIG_SENSORS_DS1621 is not set +# CONFIG_SENSORS_I5K_AMB is not set +# CONFIG_SENSORS_F71805F is not set +# CONFIG_SENSORS_F71882FG is not set +# CONFIG_SENSORS_F75375S is not set +# CONFIG_SENSORS_GL518SM is not set +# CONFIG_SENSORS_GL520SM is not set +# CONFIG_SENSORS_IT87 is not set +# CONFIG_SENSORS_LM63 is not set +# CONFIG_SENSORS_LM75 is not set +# CONFIG_SENSORS_LM77 is not set +# CONFIG_SENSORS_LM78 is not set +# CONFIG_SENSORS_LM80 is not set +# CONFIG_SENSORS_LM83 is not set +# CONFIG_SENSORS_LM85 is not set +# CONFIG_SENSORS_LM87 is not set +# CONFIG_SENSORS_LM90 is not set +# CONFIG_SENSORS_LM92 is not set +# CONFIG_SENSORS_LM93 is not set +# CONFIG_SENSORS_MAX1619 is not set +# CONFIG_SENSORS_MAX6650 is not set +# CONFIG_SENSORS_PC87360 is not set +# CONFIG_SENSORS_PC87427 is not set +# CONFIG_SENSORS_SIS5595 is not set +# CONFIG_SENSORS_DME1737 is not set +# CONFIG_SENSORS_SMSC47M1 is not set +# CONFIG_SENSORS_SMSC47M192 is not set +# CONFIG_SENSORS_SMSC47B397 is not set +# CONFIG_SENSORS_ADS7828 is not set +# CONFIG_SENSORS_THMC50 is not set +# CONFIG_SENSORS_VIA686A is not set +# CONFIG_SENSORS_VT1211 is not set +# CONFIG_SENSORS_VT8231 is not set +# CONFIG_SENSORS_W83781D is not set +# CONFIG_SENSORS_W83791D is not set +# CONFIG_SENSORS_W83792D is not set +# CONFIG_SENSORS_W83793 is not set +# CONFIG_SENSORS_W83L785TS is not set +# CONFIG_SENSORS_W83L786NG is not set +# CONFIG_SENSORS_W83627HF is not set +# CONFIG_SENSORS_W83627EHF is not set +# CONFIG_HWMON_DEBUG_CHIP is not set +# CONFIG_WATCHDOG is not set + +# +# Sonics Silicon Backplane +# +CONFIG_SSB_POSSIBLE=y +# CONFIG_SSB is not set + +# +# Multifunction device drivers +# +# CONFIG_MFD_SM501 is not set +# CONFIG_MFD_ASIC3 is not set +# CONFIG_HTC_PASIC3 is not set + +# +# Multimedia devices +# + +# +# Multimedia core support +# +# CONFIG_VIDEO_DEV is not set +# CONFIG_DVB_CORE is not set +# CONFIG_VIDEO_MEDIA is not set + +# +# Multimedia drivers +# +# CONFIG_DAB is not set + +# +# Graphics support +# +# CONFIG_DRM is not set +# CONFIG_VGASTATE is not set +# CONFIG_VIDEO_OUTPUT_CONTROL is not set +# CONFIG_FB is not set +# CONFIG_BACKLIGHT_LCD_SUPPORT is not set + +# +# Display device support +# +# CONFIG_DISPLAY_SUPPORT is not set + +# +# Sound +# +# CONFIG_SOUND is not set +CONFIG_HID_SUPPORT=y +CONFIG_HID=y +# CONFIG_HID_DEBUG is not set +# CONFIG_HIDRAW is not set + +# +# USB Input Devices +# +CONFIG_USB_HID=y +# CONFIG_USB_HIDINPUT_POWERBOOK is not set +# CONFIG_HID_FF is not set +# CONFIG_USB_HIDDEV is not set +CONFIG_USB_SUPPORT=y +CONFIG_USB_ARCH_HAS_HCD=y +CONFIG_USB_ARCH_HAS_OHCI=y +CONFIG_USB_ARCH_HAS_EHCI=y +CONFIG_USB=y +# CONFIG_USB_DEBUG is not set +# CONFIG_USB_ANNOUNCE_NEW_DEVICES is not set + +# +# Miscellaneous USB options +# +CONFIG_USB_DEVICEFS=y +CONFIG_USB_DEVICE_CLASS=y +# CONFIG_USB_DYNAMIC_MINORS is not set +# CONFIG_USB_OTG is not set +# CONFIG_USB_OTG_WHITELIST is not set +# CONFIG_USB_OTG_BLACKLIST_HUB is not set + +# +# USB Host Controller Drivers +# +# CONFIG_USB_C67X00_HCD is not set +CONFIG_USB_EHCI_HCD=y +CONFIG_USB_EHCI_ROOT_HUB_TT=y +CONFIG_USB_EHCI_TT_NEWSCHED=y +# CONFIG_USB_ISP116X_HCD is not set +# CONFIG_USB_ISP1760_HCD is not set +# CONFIG_USB_OHCI_HCD is not set +# CONFIG_USB_UHCI_HCD is not set +# CONFIG_USB_SL811_HCD is not set +# CONFIG_USB_R8A66597_HCD is not set + +# +# USB Device Class drivers +# +# CONFIG_USB_ACM is not set +CONFIG_USB_PRINTER=y +# CONFIG_USB_WDM is not set + +# +# NOTE: USB_STORAGE enables SCSI, and 'SCSI disk support' +# + +# +# may also be needed; see USB_STORAGE Help for more information +# +CONFIG_USB_STORAGE=y +# CONFIG_USB_STORAGE_DEBUG is not set +CONFIG_USB_STORAGE_DATAFAB=y +CONFIG_USB_STORAGE_FREECOM=y +# CONFIG_USB_STORAGE_ISD200 is not set +CONFIG_USB_STORAGE_DPCM=y +# CONFIG_USB_STORAGE_USBAT is not set +CONFIG_USB_STORAGE_SDDR09=y +CONFIG_USB_STORAGE_SDDR55=y +CONFIG_USB_STORAGE_JUMPSHOT=y +# CONFIG_USB_STORAGE_ALAUDA is not set +# CONFIG_USB_STORAGE_ONETOUCH is not set +# CONFIG_USB_STORAGE_KARMA is not set +# CONFIG_USB_STORAGE_CYPRESS_ATACB is not set +# CONFIG_USB_LIBUSUAL is not set + +# +# USB Imaging devices +# +# CONFIG_USB_MDC800 is not set +# CONFIG_USB_MICROTEK is not set +# CONFIG_USB_MON is not set + +# +# USB port drivers +# +# CONFIG_USB_SERIAL is not set + +# +# USB Miscellaneous drivers +# +# CONFIG_USB_EMI62 is not set +# CONFIG_USB_EMI26 is not set +# CONFIG_USB_ADUTUX is not set +# CONFIG_USB_AUERSWALD is not set +# CONFIG_USB_RIO500 is not set +# CONFIG_USB_LEGOTOWER is not set +# CONFIG_USB_LCD is not set +# CONFIG_USB_BERRY_CHARGE is not set +# CONFIG_USB_LED is not set +# CONFIG_USB_CYPRESS_CY7C63 is not set +# CONFIG_USB_CYTHERM is not set +# CONFIG_USB_PHIDGET is not set +# CONFIG_USB_IDMOUSE is not set +# CONFIG_USB_FTDI_ELAN is not set +# CONFIG_USB_APPLEDISPLAY is not set +# CONFIG_USB_SISUSBVGA is not set +# CONFIG_USB_LD is not set +# CONFIG_USB_TRANCEVIBRATOR is not set +# CONFIG_USB_IOWARRIOR is not set +# CONFIG_USB_TEST is not set +# CONFIG_USB_ISIGHTFW is not set +# CONFIG_USB_GADGET is not set +# CONFIG_MMC is not set +CONFIG_NEW_LEDS=y +CONFIG_LEDS_CLASS=y + +# +# LED drivers +# + +# +# LED Triggers +# +CONFIG_LEDS_TRIGGERS=y +CONFIG_LEDS_TRIGGER_TIMER=y +CONFIG_LEDS_TRIGGER_HEARTBEAT=y +# CONFIG_LEDS_TRIGGER_DEFAULT_ON is not set +CONFIG_RTC_LIB=y +CONFIG_RTC_CLASS=y +CONFIG_RTC_HCTOSYS=y +CONFIG_RTC_HCTOSYS_DEVICE="rtc0" +# CONFIG_RTC_DEBUG is not set + +# +# RTC interfaces +# +CONFIG_RTC_INTF_SYSFS=y +CONFIG_RTC_INTF_PROC=y +CONFIG_RTC_INTF_DEV=y +# CONFIG_RTC_INTF_DEV_UIE_EMUL is not set +# CONFIG_RTC_DRV_TEST is not set + +# +# I2C RTC drivers +# +CONFIG_RTC_DRV_DS1307=y +# CONFIG_RTC_DRV_DS1374 is not set +# CONFIG_RTC_DRV_DS1672 is not set +# CONFIG_RTC_DRV_MAX6900 is not set +CONFIG_RTC_DRV_RS5C372=y +# CONFIG_RTC_DRV_ISL1208 is not set +# CONFIG_RTC_DRV_X1205 is not set +# CONFIG_RTC_DRV_PCF8563 is not set +# CONFIG_RTC_DRV_PCF8583 is not set +CONFIG_RTC_DRV_M41T80=y +# CONFIG_RTC_DRV_M41T80_WDT is not set +# CONFIG_RTC_DRV_S35390A is not set + +# +# SPI RTC drivers +# + +# +# Platform RTC drivers +# +# CONFIG_RTC_DRV_CMOS is not set +# CONFIG_RTC_DRV_DS1511 is not set +# CONFIG_RTC_DRV_DS1553 is not set +# CONFIG_RTC_DRV_DS1742 is not set +# CONFIG_RTC_DRV_STK17TA8 is not set +# CONFIG_RTC_DRV_M48T86 is not set +# CONFIG_RTC_DRV_M48T59 is not set +# CONFIG_RTC_DRV_V3020 is not set + +# +# on-CPU RTC drivers +# +# CONFIG_UIO is not set + +# +# File systems +# +CONFIG_EXT2_FS=y +# CONFIG_EXT2_FS_XATTR is not set +# CONFIG_EXT2_FS_XIP is not set +CONFIG_EXT3_FS=y +# CONFIG_EXT3_FS_XATTR is not set +# CONFIG_EXT4DEV_FS is not set +CONFIG_JBD=y +# CONFIG_REISERFS_FS is not set +# CONFIG_JFS_FS is not set +# CONFIG_FS_POSIX_ACL is not set +# CONFIG_XFS_FS is not set +# CONFIG_OCFS2_FS is not set +CONFIG_DNOTIFY=y +CONFIG_INOTIFY=y +CONFIG_INOTIFY_USER=y +# CONFIG_QUOTA is not set +# CONFIG_AUTOFS_FS is not set +# CONFIG_AUTOFS4_FS is not set +# CONFIG_FUSE_FS is not set + +# +# CD-ROM/DVD Filesystems +# +CONFIG_ISO9660_FS=m +CONFIG_JOLIET=y +# CONFIG_ZISOFS is not set +CONFIG_UDF_FS=m +CONFIG_UDF_NLS=y + +# +# DOS/FAT/NT Filesystems +# +CONFIG_FAT_FS=y +CONFIG_MSDOS_FS=y +CONFIG_VFAT_FS=y +CONFIG_FAT_DEFAULT_CODEPAGE=437 +CONFIG_FAT_DEFAULT_IOCHARSET="iso8859-1" +# CONFIG_NTFS_FS is not set + +# +# Pseudo filesystems +# +CONFIG_PROC_FS=y +CONFIG_PROC_SYSCTL=y +CONFIG_SYSFS=y +CONFIG_TMPFS=y +# CONFIG_TMPFS_POSIX_ACL is not set +# CONFIG_HUGETLB_PAGE is not set +# CONFIG_CONFIGFS_FS is not set + +# +# Miscellaneous filesystems +# +# CONFIG_ADFS_FS is not set +# CONFIG_AFFS_FS is not set +# CONFIG_HFS_FS is not set +# CONFIG_HFSPLUS_FS is not set +# CONFIG_BEFS_FS is not set +# CONFIG_BFS_FS is not set +# CONFIG_EFS_FS is not set +CONFIG_JFFS2_FS=y +CONFIG_JFFS2_FS_DEBUG=0 +CONFIG_JFFS2_FS_WRITEBUFFER=y +# CONFIG_JFFS2_FS_WBUF_VERIFY is not set +# CONFIG_JFFS2_SUMMARY is not set +# CONFIG_JFFS2_FS_XATTR is not set +# CONFIG_JFFS2_COMPRESSION_OPTIONS is not set +CONFIG_JFFS2_ZLIB=y +# CONFIG_JFFS2_LZO is not set +CONFIG_JFFS2_RTIME=y +# CONFIG_JFFS2_RUBIN is not set +CONFIG_CRAMFS=y +# CONFIG_VXFS_FS is not set +# CONFIG_MINIX_FS is not set +# CONFIG_HPFS_FS is not set +# CONFIG_QNX4FS_FS is not set +# CONFIG_ROMFS_FS is not set +# CONFIG_SYSV_FS is not set +# CONFIG_UFS_FS is not set +CONFIG_NETWORK_FILESYSTEMS=y +CONFIG_NFS_FS=y +CONFIG_NFS_V3=y +# CONFIG_NFS_V3_ACL is not set +# CONFIG_NFS_V4 is not set +# CONFIG_NFSD is not set +CONFIG_ROOT_NFS=y +CONFIG_LOCKD=y +CONFIG_LOCKD_V4=y +CONFIG_NFS_COMMON=y +CONFIG_SUNRPC=y +# CONFIG_SUNRPC_BIND34 is not set +# CONFIG_RPCSEC_GSS_KRB5 is not set +# CONFIG_RPCSEC_GSS_SPKM3 is not set +# CONFIG_SMB_FS is not set +# CONFIG_CIFS is not set +# CONFIG_NCP_FS is not set +# CONFIG_CODA_FS is not set +# CONFIG_AFS_FS is not set + +# +# Partition Types +# +CONFIG_PARTITION_ADVANCED=y +# CONFIG_ACORN_PARTITION is not set +# CONFIG_OSF_PARTITION is not set +# CONFIG_AMIGA_PARTITION is not set +# CONFIG_ATARI_PARTITION is not set +# CONFIG_MAC_PARTITION is not set +CONFIG_MSDOS_PARTITION=y +CONFIG_BSD_DISKLABEL=y +# CONFIG_MINIX_SUBPARTITION is not set +# CONFIG_SOLARIS_X86_PARTITION is not set +# CONFIG_UNIXWARE_DISKLABEL is not set +# CONFIG_LDM_PARTITION is not set +# CONFIG_SGI_PARTITION is not set +# CONFIG_ULTRIX_PARTITION is not set +# CONFIG_SUN_PARTITION is not set +# CONFIG_KARMA_PARTITION is not set +# CONFIG_EFI_PARTITION is not set +# CONFIG_SYSV68_PARTITION is not set +CONFIG_NLS=y +CONFIG_NLS_DEFAULT="iso8859-1" +CONFIG_NLS_CODEPAGE_437=y +# CONFIG_NLS_CODEPAGE_737 is not set +# CONFIG_NLS_CODEPAGE_775 is not set +CONFIG_NLS_CODEPAGE_850=y +# CONFIG_NLS_CODEPAGE_852 is not set +# CONFIG_NLS_CODEPAGE_855 is not set +# CONFIG_NLS_CODEPAGE_857 is not set +# CONFIG_NLS_CODEPAGE_860 is not set +# CONFIG_NLS_CODEPAGE_861 is not set +# CONFIG_NLS_CODEPAGE_862 is not set +# CONFIG_NLS_CODEPAGE_863 is not set +# CONFIG_NLS_CODEPAGE_864 is not set +# CONFIG_NLS_CODEPAGE_865 is not set +# CONFIG_NLS_CODEPAGE_866 is not set +# CONFIG_NLS_CODEPAGE_869 is not set +# CONFIG_NLS_CODEPAGE_936 is not set +# CONFIG_NLS_CODEPAGE_950 is not set +# CONFIG_NLS_CODEPAGE_932 is not set +# CONFIG_NLS_CODEPAGE_949 is not set +# CONFIG_NLS_CODEPAGE_874 is not set +# CONFIG_NLS_ISO8859_8 is not set +# CONFIG_NLS_CODEPAGE_1250 is not set +# CONFIG_NLS_CODEPAGE_1251 is not set +# CONFIG_NLS_ASCII is not set +CONFIG_NLS_ISO8859_1=y +CONFIG_NLS_ISO8859_2=y +# CONFIG_NLS_ISO8859_3 is not set +# CONFIG_NLS_ISO8859_4 is not set +# CONFIG_NLS_ISO8859_5 is not set +# CONFIG_NLS_ISO8859_6 is not set +# CONFIG_NLS_ISO8859_7 is not set +# CONFIG_NLS_ISO8859_9 is not set +# CONFIG_NLS_ISO8859_13 is not set +# CONFIG_NLS_ISO8859_14 is not set +# CONFIG_NLS_ISO8859_15 is not set +# CONFIG_NLS_KOI8_R is not set +# CONFIG_NLS_KOI8_U is not set +# CONFIG_NLS_UTF8 is not set +# CONFIG_DLM is not set + +# +# Kernel hacking +# +# CONFIG_PRINTK_TIME is not set +CONFIG_ENABLE_WARN_DEPRECATED=y +CONFIG_ENABLE_MUST_CHECK=y +CONFIG_FRAME_WARN=1024 +CONFIG_MAGIC_SYSRQ=y +# CONFIG_UNUSED_SYMBOLS is not set +# CONFIG_DEBUG_FS is not set +# CONFIG_HEADERS_CHECK is not set +CONFIG_DEBUG_KERNEL=y +# CONFIG_DEBUG_SHIRQ is not set +CONFIG_DETECT_SOFTLOCKUP=y +CONFIG_SCHED_DEBUG=y +CONFIG_SCHEDSTATS=y +# CONFIG_TIMER_STATS is not set +# CONFIG_DEBUG_OBJECTS is not set +CONFIG_DEBUG_PREEMPT=y +# CONFIG_DEBUG_RT_MUTEXES is not set +# CONFIG_RT_MUTEX_TESTER is not set +# CONFIG_DEBUG_SPINLOCK is not set +# CONFIG_DEBUG_MUTEXES is not set +# CONFIG_DEBUG_LOCK_ALLOC is not set +# CONFIG_PROVE_LOCKING is not set +# CONFIG_LOCK_STAT is not set +# CONFIG_DEBUG_SPINLOCK_SLEEP is not set +# CONFIG_DEBUG_LOCKING_API_SELFTESTS is not set +# CONFIG_DEBUG_KOBJECT is not set +# CONFIG_DEBUG_BUGVERBOSE is not set +CONFIG_DEBUG_INFO=y +# CONFIG_DEBUG_VM is not set +# CONFIG_DEBUG_WRITECOUNT is not set +# CONFIG_DEBUG_LIST is not set +# CONFIG_DEBUG_SG is not set +CONFIG_FRAME_POINTER=y +# CONFIG_BOOT_PRINTK_DELAY is not set +# CONFIG_RCU_TORTURE_TEST is not set +# CONFIG_KPROBES_SANITY_TEST is not set +# CONFIG_BACKTRACE_SELF_TEST is not set +# CONFIG_LKDTM is not set +# CONFIG_FAULT_INJECTION is not set +# CONFIG_LATENCYTOP is not set +# CONFIG_SAMPLES is not set +CONFIG_DEBUG_USER=y +CONFIG_DEBUG_ERRORS=y +# CONFIG_DEBUG_STACK_USAGE is not set +CONFIG_DEBUG_LL=y +# CONFIG_DEBUG_ICEDCC is not set + +# +# Security options +# +# CONFIG_KEYS is not set +# CONFIG_SECURITY is not set +# CONFIG_SECURITY_FILE_CAPABILITIES is not set +CONFIG_CRYPTO=y + +# +# Crypto core or helper +# +CONFIG_CRYPTO_ALGAPI=m +CONFIG_CRYPTO_BLKCIPHER=m +CONFIG_CRYPTO_MANAGER=m +# CONFIG_CRYPTO_GF128MUL is not set +# CONFIG_CRYPTO_NULL is not set +# CONFIG_CRYPTO_CRYPTD is not set +# CONFIG_CRYPTO_AUTHENC is not set +# CONFIG_CRYPTO_TEST is not set + +# +# Authenticated Encryption with Associated Data +# +# CONFIG_CRYPTO_CCM is not set +# CONFIG_CRYPTO_GCM is not set +# CONFIG_CRYPTO_SEQIV is not set + +# +# Block modes +# +CONFIG_CRYPTO_CBC=m +# CONFIG_CRYPTO_CTR is not set +# CONFIG_CRYPTO_CTS is not set +CONFIG_CRYPTO_ECB=m +# CONFIG_CRYPTO_LRW is not set +CONFIG_CRYPTO_PCBC=m +# CONFIG_CRYPTO_XTS is not set + +# +# Hash modes +# +# CONFIG_CRYPTO_HMAC is not set +# CONFIG_CRYPTO_XCBC is not set + +# +# Digest +# +# CONFIG_CRYPTO_CRC32C is not set +# CONFIG_CRYPTO_MD4 is not set +# CONFIG_CRYPTO_MD5 is not set +# CONFIG_CRYPTO_MICHAEL_MIC is not set +# CONFIG_CRYPTO_SHA1 is not set +# CONFIG_CRYPTO_SHA256 is not set +# CONFIG_CRYPTO_SHA512 is not set +# CONFIG_CRYPTO_TGR192 is not set +# CONFIG_CRYPTO_WP512 is not set + +# +# Ciphers +# +# CONFIG_CRYPTO_AES is not set +# CONFIG_CRYPTO_ANUBIS is not set +# CONFIG_CRYPTO_ARC4 is not set +# CONFIG_CRYPTO_BLOWFISH is not set +# CONFIG_CRYPTO_CAMELLIA is not set +# CONFIG_CRYPTO_CAST5 is not set +# CONFIG_CRYPTO_CAST6 is not set +# CONFIG_CRYPTO_DES is not set +# CONFIG_CRYPTO_FCRYPT is not set +# CONFIG_CRYPTO_KHAZAD is not set +# CONFIG_CRYPTO_SALSA20 is not set +# CONFIG_CRYPTO_SEED is not set +# CONFIG_CRYPTO_SERPENT is not set +# CONFIG_CRYPTO_TEA is not set +# CONFIG_CRYPTO_TWOFISH is not set + +# +# Compression +# +# CONFIG_CRYPTO_DEFLATE is not set +# CONFIG_CRYPTO_LZO is not set +CONFIG_CRYPTO_HW=y +# CONFIG_CRYPTO_DEV_HIFN_795X is not set + +# +# Library routines +# +CONFIG_BITREVERSE=y +# CONFIG_GENERIC_FIND_FIRST_BIT is not set +# CONFIG_GENERIC_FIND_NEXT_BIT is not set +# CONFIG_CRC_CCITT is not set +# CONFIG_CRC16 is not set +CONFIG_CRC_ITU_T=m +CONFIG_CRC32=y +# CONFIG_CRC7 is not set +# CONFIG_LIBCRC32C is not set +CONFIG_ZLIB_INFLATE=y +CONFIG_ZLIB_DEFLATE=y +CONFIG_PLIST=y +CONFIG_HAS_IOMEM=y +CONFIG_HAS_IOPORT=y +CONFIG_HAS_DMA=y diff --git a/arch/arm/configs/netx_defconfig b/arch/arm/configs/netx_defconfig index 57f32f39d0f..0884f2370c3 100644 --- a/arch/arm/configs/netx_defconfig +++ b/arch/arm/configs/netx_defconfig @@ -154,7 +154,6 @@ CONFIG_ARM_AMBA=y # Kernel Features # CONFIG_PREEMPT=y -# CONFIG_NO_IDLE_HZ is not set CONFIG_HZ=100 # CONFIG_AEABI is not set # CONFIG_ARCH_DISCONTIGMEM_ENABLE is not set diff --git a/arch/arm/configs/onearm_defconfig b/arch/arm/configs/onearm_defconfig index 650a248613e..418ca2febbe 100644 --- a/arch/arm/configs/onearm_defconfig +++ b/arch/arm/configs/onearm_defconfig @@ -202,7 +202,6 @@ CONFIG_AT91_CF=y # Kernel Features # # CONFIG_PREEMPT is not set -# CONFIG_NO_IDLE_HZ is not set CONFIG_HZ=100 # CONFIG_AEABI is not set # CONFIG_ARCH_DISCONTIGMEM_ENABLE is not set diff --git a/arch/arm/configs/orion5x_defconfig b/arch/arm/configs/orion5x_defconfig index 52cd99bd52f..9578b5d9f9c 100644 --- a/arch/arm/configs/orion5x_defconfig +++ b/arch/arm/configs/orion5x_defconfig @@ -1,7 +1,7 @@ # # Automatically generated make config: don't edit -# Linux kernel version: 2.6.24 -# Thu Feb 7 14:10:30 2008 +# Linux kernel version: 2.6.26-rc4 +# Mon Jun 2 23:54:48 2008 # CONFIG_ARM=y CONFIG_SYS_SUPPORTS_APM_EMULATION=y @@ -21,6 +21,7 @@ CONFIG_RWSEM_GENERIC_SPINLOCK=y # CONFIG_ARCH_HAS_ILOG2_U64 is not set CONFIG_GENERIC_HWEIGHT=y CONFIG_GENERIC_CALIBRATE_DELAY=y +CONFIG_ARCH_SUPPORTS_AOUT=y CONFIG_ZONE_DMA=y CONFIG_VECTORS_BASE=0xffff0000 CONFIG_DEFCONFIG_LIST="/lib/modules/$UNAME_RELEASE/.config" @@ -40,24 +41,24 @@ CONFIG_SYSVIPC_SYSCTL=y # CONFIG_POSIX_MQUEUE is not set # CONFIG_BSD_PROCESS_ACCT is not set # CONFIG_TASKSTATS is not set -# CONFIG_USER_NS is not set -# CONFIG_PID_NS is not set # CONFIG_AUDIT is not set # CONFIG_IKCONFIG is not set CONFIG_LOG_BUF_SHIFT=14 # CONFIG_CGROUPS is not set -CONFIG_FAIR_GROUP_SCHED=y -CONFIG_FAIR_USER_SCHED=y -# CONFIG_FAIR_CGROUP_SCHED is not set +# CONFIG_GROUP_SCHED is not set CONFIG_SYSFS_DEPRECATED=y +CONFIG_SYSFS_DEPRECATED_V2=y # CONFIG_RELAY is not set +# CONFIG_NAMESPACES is not set # CONFIG_BLK_DEV_INITRD is not set CONFIG_CC_OPTIMIZE_FOR_SIZE=y CONFIG_SYSCTL=y CONFIG_EMBEDDED=y CONFIG_UID16=y CONFIG_SYSCTL_SYSCALL=y +CONFIG_SYSCTL_SYSCALL_CHECK=y CONFIG_KALLSYMS=y +CONFIG_KALLSYMS_ALL=y # CONFIG_KALLSYMS_EXTRA_PASS is not set CONFIG_HOTPLUG=y CONFIG_PRINTK=y @@ -73,20 +74,25 @@ CONFIG_TIMERFD=y CONFIG_EVENTFD=y CONFIG_SHMEM=y CONFIG_VM_EVENT_COUNTERS=y -CONFIG_SLAB=y -# CONFIG_SLUB is not set +# CONFIG_SLUB_DEBUG is not set +# CONFIG_SLAB is not set +CONFIG_SLUB=y # CONFIG_SLOB is not set -# CONFIG_PROFILING is not set +CONFIG_PROFILING=y # CONFIG_MARKERS is not set +CONFIG_OPROFILE=y CONFIG_HAVE_OPROFILE=y -# CONFIG_KPROBES is not set +CONFIG_KPROBES=y +CONFIG_KRETPROBES=y CONFIG_HAVE_KPROBES=y +CONFIG_HAVE_KRETPROBES=y +# CONFIG_HAVE_DMA_ATTRS is not set CONFIG_PROC_PAGE_MONITOR=y -CONFIG_SLABINFO=y CONFIG_RT_MUTEXES=y # CONFIG_TINY_SHMEM is not set CONFIG_BASE_SMALL=0 CONFIG_MODULES=y +# CONFIG_MODULE_FORCE_LOAD is not set CONFIG_MODULE_UNLOAD=y # CONFIG_MODULE_FORCE_UNLOAD is not set # CONFIG_MODVERSIONS is not set @@ -111,7 +117,6 @@ CONFIG_DEFAULT_CFQ=y # CONFIG_DEFAULT_NOOP is not set CONFIG_DEFAULT_IOSCHED="cfq" CONFIG_CLASSIC_RCU=y -# CONFIG_PREEMPT_RCU is not set # # System Type @@ -160,6 +165,15 @@ CONFIG_MACH_RD88F5182=y CONFIG_MACH_KUROBOX_PRO=y CONFIG_MACH_DNS323=y CONFIG_MACH_TS209=y +CONFIG_MACH_LINKSTATION_PRO=y +CONFIG_MACH_TS409=y +CONFIG_MACH_WRT350N_V2=y +CONFIG_MACH_TS78XX=y +CONFIG_MACH_MV2120=y +CONFIG_MACH_MSS2=y +CONFIG_MACH_WNR854T=y +CONFIG_MACH_RD88F5181L_GE=y +CONFIG_MACH_RD88F5181L_FXO=y # # Boot options @@ -168,6 +182,7 @@ CONFIG_MACH_TS209=y # # Power management # +CONFIG_PLAT_ORION=y # # Processor Type @@ -177,8 +192,9 @@ CONFIG_CPU_FEROCEON=y CONFIG_CPU_FEROCEON_OLD_ID=y CONFIG_CPU_32v5=y CONFIG_CPU_ABRT_EV5T=y +CONFIG_CPU_PABRT_NOIFAR=y CONFIG_CPU_CACHE_VIVT=y -CONFIG_CPU_COPY_V4WB=y +CONFIG_CPU_COPY_FEROCEON=y CONFIG_CPU_TLB_V4WBI=y CONFIG_CPU_CP15=y CONFIG_CPU_CP15_MMU=y @@ -189,7 +205,6 @@ CONFIG_CPU_CP15_MMU=y CONFIG_ARM_THUMB=y # CONFIG_CPU_ICACHE_DISABLE is not set # CONFIG_CPU_DCACHE_DISABLE is not set -# CONFIG_CPU_DCACHE_WRITETHROUGH is not set # CONFIG_OUTER_CACHE is not set # @@ -199,6 +214,7 @@ CONFIG_PCI=y CONFIG_PCI_SYSCALL=y # CONFIG_ARCH_SUPPORTS_MSI is not set CONFIG_PCI_LEGACY=y +# CONFIG_PCI_DEBUG is not set # CONFIG_PCCARD is not set # @@ -221,6 +237,7 @@ CONFIG_FLATMEM=y CONFIG_FLAT_NODE_MEM_MAP=y # CONFIG_SPARSEMEM_STATIC is not set # CONFIG_SPARSEMEM_VMEMMAP_ENABLE is not set +CONFIG_PAGEFLAGS_EXTENDED=y CONFIG_SPLIT_PTLOCK_CPUS=4096 # CONFIG_RESOURCES_64BIT is not set CONFIG_ZONE_DMA_FLAG=1 @@ -238,7 +255,6 @@ CONFIG_ZBOOT_ROM_BSS=0x0 CONFIG_CMDLINE="" # CONFIG_XIP_KERNEL is not set # CONFIG_KEXEC is not set -# CONFIG_ATAGS_PROC is not set # # Floating point emulation @@ -311,8 +327,6 @@ CONFIG_TCP_CONG_CUBIC=y CONFIG_DEFAULT_TCP_CONG="cubic" # CONFIG_TCP_MD5SIG is not set # CONFIG_IPV6 is not set -# CONFIG_INET6_XFRM_TUNNEL is not set -# CONFIG_INET6_TUNNEL is not set # CONFIG_NETWORK_SECMARK is not set # CONFIG_NETFILTER is not set # CONFIG_IP_DCCP is not set @@ -335,6 +349,7 @@ CONFIG_DEFAULT_TCP_CONG="cubic" # Network testing # CONFIG_NET_PKTGEN=m +# CONFIG_NET_TCPPROBE is not set # CONFIG_HAMRADIO is not set # CONFIG_CAN is not set # CONFIG_IRDA is not set @@ -362,6 +377,8 @@ CONFIG_UEVENT_HELPER_PATH="/sbin/hotplug" CONFIG_STANDALONE=y CONFIG_PREVENT_FIRMWARE_BUILD=y CONFIG_FW_LOADER=y +# CONFIG_DEBUG_DRIVER is not set +# CONFIG_DEBUG_DEVRES is not set # CONFIG_SYS_HYPERVISOR is not set # CONFIG_CONNECTOR is not set CONFIG_MTD=y @@ -371,6 +388,7 @@ CONFIG_MTD_PARTITIONS=y # CONFIG_MTD_REDBOOT_PARTS is not set CONFIG_MTD_CMDLINE_PARTS=y # CONFIG_MTD_AFS_PARTS is not set +# CONFIG_MTD_AR7_PARTS is not set # # User Modules And Translation Layers @@ -378,9 +396,8 @@ CONFIG_MTD_CMDLINE_PARTS=y CONFIG_MTD_CHAR=y CONFIG_MTD_BLKDEVS=y CONFIG_MTD_BLOCK=y -CONFIG_FTL=y -CONFIG_NFTL=y -# CONFIG_NFTL_RW is not set +# CONFIG_FTL is not set +# CONFIG_NFTL is not set # CONFIG_INFTL is not set # CONFIG_RFD_FTL is not set # CONFIG_SSFDC is not set @@ -405,12 +422,12 @@ CONFIG_MTD_MAP_BANK_WIDTH_4=y # CONFIG_MTD_MAP_BANK_WIDTH_32 is not set CONFIG_MTD_CFI_I1=y CONFIG_MTD_CFI_I2=y -CONFIG_MTD_CFI_I4=y +# CONFIG_MTD_CFI_I4 is not set # CONFIG_MTD_CFI_I8 is not set # CONFIG_MTD_OTP is not set CONFIG_MTD_CFI_INTELEXT=y CONFIG_MTD_CFI_AMDSTD=y -CONFIG_MTD_CFI_STAA=y +# CONFIG_MTD_CFI_STAA is not set CONFIG_MTD_CFI_UTIL=y # CONFIG_MTD_RAM is not set # CONFIG_MTD_ROM is not set @@ -481,6 +498,9 @@ CONFIG_MISC_DEVICES=y # CONFIG_EEPROM_93CX6 is not set # CONFIG_SGI_IOC4 is not set # CONFIG_TIFM_CORE is not set +# CONFIG_ENCLOSURE_SERVICES is not set +CONFIG_HAVE_IDE=y +# CONFIG_IDE is not set # # SCSI device support @@ -542,6 +562,7 @@ CONFIG_SCSI_LOWLEVEL=y # CONFIG_SCSI_IPS is not set # CONFIG_SCSI_INITIO is not set # CONFIG_SCSI_INIA100 is not set +# CONFIG_SCSI_MVSAS is not set # CONFIG_SCSI_STEX is not set # CONFIG_SCSI_SYM53C8XX_2 is not set # CONFIG_SCSI_IPR is not set @@ -556,7 +577,10 @@ CONFIG_SCSI_LOWLEVEL=y # CONFIG_SCSI_SRP is not set CONFIG_ATA=y # CONFIG_ATA_NONSTANDARD is not set +CONFIG_SATA_PMP=y # CONFIG_SATA_AHCI is not set +# CONFIG_SATA_SIL24 is not set +CONFIG_ATA_SFF=y # CONFIG_SATA_SVW is not set # CONFIG_ATA_PIIX is not set CONFIG_SATA_MV=y @@ -566,7 +590,6 @@ CONFIG_SATA_MV=y # CONFIG_SATA_PROMISE is not set # CONFIG_SATA_SX4 is not set # CONFIG_SATA_SIL is not set -# CONFIG_SATA_SIL24 is not set # CONFIG_SATA_SIS is not set # CONFIG_SATA_ULI is not set # CONFIG_SATA_VIA is not set @@ -611,6 +634,7 @@ CONFIG_SATA_MV=y # CONFIG_PATA_VIA is not set # CONFIG_PATA_WINBOND is not set # CONFIG_PATA_PLATFORM is not set +# CONFIG_PATA_SCH is not set # CONFIG_MD is not set # CONFIG_FUSION is not set @@ -652,7 +676,7 @@ CONFIG_NET_PCI=y # CONFIG_B44 is not set # CONFIG_FORCEDETH is not set # CONFIG_EEPRO100 is not set -CONFIG_E100=y +# CONFIG_E100 is not set # CONFIG_FEALNX is not set # CONFIG_NATSEMI is not set # CONFIG_NE2K_PCI is not set @@ -668,9 +692,7 @@ CONFIG_E100=y CONFIG_NETDEV_1000=y # CONFIG_ACENIC is not set # CONFIG_DL2K is not set -CONFIG_E1000=y -CONFIG_E1000_NAPI=y -# CONFIG_E1000_DISABLE_PACKET_SPLIT is not set +# CONFIG_E1000 is not set # CONFIG_E1000E is not set # CONFIG_E1000E_ENABLED is not set # CONFIG_IP1000 is not set @@ -680,27 +702,15 @@ CONFIG_E1000_NAPI=y # CONFIG_YELLOWFIN is not set # CONFIG_R8169 is not set # CONFIG_SIS190 is not set -CONFIG_SKGE=y -CONFIG_SKY2=y -# CONFIG_SK98LIN is not set +# CONFIG_SKGE is not set +# CONFIG_SKY2 is not set # CONFIG_VIA_VELOCITY is not set -CONFIG_TIGON3=y +# CONFIG_TIGON3 is not set # CONFIG_BNX2 is not set CONFIG_MV643XX_ETH=y # CONFIG_QLA3XXX is not set # CONFIG_ATL1 is not set -CONFIG_NETDEV_10000=y -# CONFIG_CHELSIO_T1 is not set -# CONFIG_CHELSIO_T3 is not set -# CONFIG_IXGBE is not set -# CONFIG_IXGB is not set -# CONFIG_S2IO is not set -# CONFIG_MYRI10GE is not set -# CONFIG_NETXEN_NIC is not set -# CONFIG_NIU is not set -# CONFIG_MLX4_CORE is not set -# CONFIG_TEHUTI is not set -# CONFIG_BNX2X is not set +# CONFIG_NETDEV_10000 is not set # CONFIG_TR is not set # @@ -708,6 +718,7 @@ CONFIG_NETDEV_10000=y # # CONFIG_WLAN_PRE80211 is not set # CONFIG_WLAN_80211 is not set +# CONFIG_IWLWIFI_LEDS is not set # # USB Network Adapters @@ -738,12 +749,9 @@ CONFIG_INPUT=y # # Userland interfaces # -CONFIG_INPUT_MOUSEDEV=y -CONFIG_INPUT_MOUSEDEV_PSAUX=y -CONFIG_INPUT_MOUSEDEV_SCREEN_X=1024 -CONFIG_INPUT_MOUSEDEV_SCREEN_Y=768 +# CONFIG_INPUT_MOUSEDEV is not set # CONFIG_INPUT_JOYDEV is not set -# CONFIG_INPUT_EVDEV is not set +CONFIG_INPUT_EVDEV=y # CONFIG_INPUT_EVBUG is not set # @@ -765,10 +773,8 @@ CONFIG_INPUT_MOUSEDEV_SCREEN_Y=768 # # Character devices # -CONFIG_VT=y -CONFIG_VT_CONSOLE=y -CONFIG_HW_CONSOLE=y -# CONFIG_VT_HW_CONSOLE_BINDING is not set +# CONFIG_VT is not set +CONFIG_DEVKMEM=y # CONFIG_SERIAL_NONSTANDARD is not set # CONFIG_NOZOMI is not set @@ -777,7 +783,7 @@ CONFIG_HW_CONSOLE=y # CONFIG_SERIAL_8250=y CONFIG_SERIAL_8250_CONSOLE=y -CONFIG_SERIAL_8250_PCI=y +# CONFIG_SERIAL_8250_PCI is not set CONFIG_SERIAL_8250_NR_UARTS=4 CONFIG_SERIAL_8250_RUNTIME_UARTS=2 # CONFIG_SERIAL_8250_EXTENDED is not set @@ -792,7 +798,7 @@ CONFIG_UNIX98_PTYS=y CONFIG_LEGACY_PTYS=y CONFIG_LEGACY_PTY_COUNT=16 # CONFIG_IPMI_HANDLER is not set -CONFIG_HW_RANDOM=m +# CONFIG_HW_RANDOM is not set # CONFIG_NVRAM is not set # CONFIG_R3964 is not set # CONFIG_APPLICOM is not set @@ -804,13 +810,6 @@ CONFIG_I2C_BOARDINFO=y CONFIG_I2C_CHARDEV=y # -# I2C Algorithms -# -# CONFIG_I2C_ALGOBIT is not set -# CONFIG_I2C_ALGOPCF is not set -# CONFIG_I2C_ALGOPCA is not set - -# # I2C Hardware Bus support # # CONFIG_I2C_ALI1535 is not set @@ -837,6 +836,7 @@ CONFIG_I2C_CHARDEV=y # CONFIG_I2C_VIA is not set # CONFIG_I2C_VIAPRO is not set # CONFIG_I2C_VOODOO3 is not set +# CONFIG_I2C_PCA_PLATFORM is not set CONFIG_I2C_MV64XXX=y # @@ -847,19 +847,13 @@ CONFIG_I2C_MV64XXX=y # CONFIG_SENSORS_PCF8574 is not set # CONFIG_PCF8575 is not set # CONFIG_SENSORS_PCF8591 is not set -# CONFIG_TPS65010 is not set # CONFIG_SENSORS_MAX6875 is not set # CONFIG_SENSORS_TSL2550 is not set # CONFIG_I2C_DEBUG_CORE is not set # CONFIG_I2C_DEBUG_ALGO is not set # CONFIG_I2C_DEBUG_BUS is not set # CONFIG_I2C_DEBUG_CHIP is not set - -# -# SPI support -# # CONFIG_SPI is not set -# CONFIG_SPI_MASTER is not set # CONFIG_W1 is not set # CONFIG_POWER_SUPPLY is not set CONFIG_HWMON=y @@ -872,6 +866,7 @@ CONFIG_HWMON=y # CONFIG_SENSORS_ADM1031 is not set # CONFIG_SENSORS_ADM9240 is not set # CONFIG_SENSORS_ADT7470 is not set +# CONFIG_SENSORS_ADT7473 is not set # CONFIG_SENSORS_ATXP1 is not set # CONFIG_SENSORS_DS1621 is not set # CONFIG_SENSORS_I5K_AMB is not set @@ -901,6 +896,7 @@ CONFIG_HWMON=y # CONFIG_SENSORS_SMSC47M1 is not set # CONFIG_SENSORS_SMSC47M192 is not set # CONFIG_SENSORS_SMSC47B397 is not set +# CONFIG_SENSORS_ADS7828 is not set # CONFIG_SENSORS_THMC50 is not set # CONFIG_SENSORS_VIA686A is not set # CONFIG_SENSORS_VT1211 is not set @@ -910,6 +906,7 @@ CONFIG_HWMON=y # CONFIG_SENSORS_W83792D is not set # CONFIG_SENSORS_W83793 is not set # CONFIG_SENSORS_W83L785TS is not set +# CONFIG_SENSORS_W83L786NG is not set # CONFIG_SENSORS_W83627HF is not set # CONFIG_SENSORS_W83627EHF is not set # CONFIG_HWMON_DEBUG_CHIP is not set @@ -925,14 +922,24 @@ CONFIG_SSB_POSSIBLE=y # Multifunction device drivers # # CONFIG_MFD_SM501 is not set +# CONFIG_MFD_ASIC3 is not set +# CONFIG_HTC_PASIC3 is not set # # Multimedia devices # + +# +# Multimedia core support +# # CONFIG_VIDEO_DEV is not set # CONFIG_DVB_CORE is not set -CONFIG_DAB=y -# CONFIG_USB_DABUSB is not set +# CONFIG_VIDEO_MEDIA is not set + +# +# Multimedia drivers +# +# CONFIG_DAB is not set # # Graphics support @@ -949,12 +956,6 @@ CONFIG_DAB=y # CONFIG_DISPLAY_SUPPORT is not set # -# Console display driver support -# -# CONFIG_VGA_CONSOLE is not set -CONFIG_DUMMY_CONSOLE=y - -# # Sound # # CONFIG_SOUND is not set @@ -985,14 +986,18 @@ CONFIG_USB_DEVICEFS=y CONFIG_USB_DEVICE_CLASS=y # CONFIG_USB_DYNAMIC_MINORS is not set # CONFIG_USB_OTG is not set +# CONFIG_USB_OTG_WHITELIST is not set +# CONFIG_USB_OTG_BLACKLIST_HUB is not set # # USB Host Controller Drivers # +# CONFIG_USB_C67X00_HCD is not set CONFIG_USB_EHCI_HCD=y CONFIG_USB_EHCI_ROOT_HUB_TT=y CONFIG_USB_EHCI_TT_NEWSCHED=y # CONFIG_USB_ISP116X_HCD is not set +# CONFIG_USB_ISP1760_HCD is not set # CONFIG_USB_OHCI_HCD is not set # CONFIG_USB_UHCI_HCD is not set # CONFIG_USB_SL811_HCD is not set @@ -1003,6 +1008,7 @@ CONFIG_USB_EHCI_TT_NEWSCHED=y # # CONFIG_USB_ACM is not set CONFIG_USB_PRINTER=y +# CONFIG_USB_WDM is not set # # NOTE: USB_STORAGE enables SCSI, and 'SCSI disk support' @@ -1022,7 +1028,9 @@ CONFIG_USB_STORAGE_SDDR09=y CONFIG_USB_STORAGE_SDDR55=y CONFIG_USB_STORAGE_JUMPSHOT=y # CONFIG_USB_STORAGE_ALAUDA is not set +# CONFIG_USB_STORAGE_ONETOUCH is not set # CONFIG_USB_STORAGE_KARMA is not set +# CONFIG_USB_STORAGE_CYPRESS_ATACB is not set # CONFIG_USB_LIBUSUAL is not set # @@ -1060,6 +1068,7 @@ CONFIG_USB_STORAGE_JUMPSHOT=y # CONFIG_USB_TRANCEVIBRATOR is not set # CONFIG_USB_IOWARRIOR is not set # CONFIG_USB_TEST is not set +# CONFIG_USB_ISIGHTFW is not set # CONFIG_USB_GADGET is not set # CONFIG_MMC is not set CONFIG_NEW_LEDS=y @@ -1068,7 +1077,7 @@ CONFIG_LEDS_CLASS=y # # LED drivers # -# CONFIG_LEDS_GPIO is not set +CONFIG_LEDS_GPIO=y # # LED Triggers @@ -1076,6 +1085,7 @@ CONFIG_LEDS_CLASS=y CONFIG_LEDS_TRIGGERS=y CONFIG_LEDS_TRIGGER_TIMER=y CONFIG_LEDS_TRIGGER_HEARTBEAT=y +CONFIG_LEDS_TRIGGER_DEFAULT_ON=y CONFIG_RTC_LIB=y CONFIG_RTC_CLASS=y CONFIG_RTC_HCTOSYS=y @@ -1105,6 +1115,7 @@ CONFIG_RTC_DRV_RS5C372=y # CONFIG_RTC_DRV_PCF8583 is not set CONFIG_RTC_DRV_M41T80=y # CONFIG_RTC_DRV_M41T80_WDT is not set +# CONFIG_RTC_DRV_S35390A is not set # # SPI RTC drivers @@ -1125,6 +1136,7 @@ CONFIG_RTC_DRV_M41T80=y # # on-CPU RTC drivers # +# CONFIG_UIO is not set # # File systems @@ -1140,14 +1152,11 @@ CONFIG_JBD=y # CONFIG_JFS_FS is not set # CONFIG_FS_POSIX_ACL is not set # CONFIG_XFS_FS is not set -# CONFIG_GFS2_FS is not set # CONFIG_OCFS2_FS is not set -# CONFIG_MINIX_FS is not set -# CONFIG_ROMFS_FS is not set +CONFIG_DNOTIFY=y CONFIG_INOTIFY=y CONFIG_INOTIFY_USER=y # CONFIG_QUOTA is not set -CONFIG_DNOTIFY=y # CONFIG_AUTOFS_FS is not set # CONFIG_AUTOFS4_FS is not set # CONFIG_FUSE_FS is not set @@ -1155,8 +1164,8 @@ CONFIG_DNOTIFY=y # # CD-ROM/DVD Filesystems # -CONFIG_ISO9660_FS=y -# CONFIG_JOLIET is not set +CONFIG_ISO9660_FS=m +CONFIG_JOLIET=y # CONFIG_ZISOFS is not set CONFIG_UDF_FS=m CONFIG_UDF_NLS=y @@ -1205,8 +1214,10 @@ CONFIG_JFFS2_RTIME=y # CONFIG_JFFS2_RUBIN is not set CONFIG_CRAMFS=y # CONFIG_VXFS_FS is not set +# CONFIG_MINIX_FS is not set # CONFIG_HPFS_FS is not set # CONFIG_QNX4FS_FS is not set +# CONFIG_ROMFS_FS is not set # CONFIG_SYSV_FS is not set # CONFIG_UFS_FS is not set CONFIG_NETWORK_FILESYSTEMS=y @@ -1214,7 +1225,6 @@ CONFIG_NFS_FS=y CONFIG_NFS_V3=y # CONFIG_NFS_V3_ACL is not set # CONFIG_NFS_V4 is not set -# CONFIG_NFS_DIRECTIO is not set # CONFIG_NFSD is not set CONFIG_ROOT_NFS=y CONFIG_LOCKD=y @@ -1241,14 +1251,13 @@ CONFIG_PARTITION_ADVANCED=y # CONFIG_MAC_PARTITION is not set CONFIG_MSDOS_PARTITION=y CONFIG_BSD_DISKLABEL=y -CONFIG_MINIX_SUBPARTITION=y -CONFIG_SOLARIS_X86_PARTITION=y -CONFIG_UNIXWARE_DISKLABEL=y -CONFIG_LDM_PARTITION=y -CONFIG_LDM_DEBUG=y +# CONFIG_MINIX_SUBPARTITION is not set +# CONFIG_SOLARIS_X86_PARTITION is not set +# CONFIG_UNIXWARE_DISKLABEL is not set +# CONFIG_LDM_PARTITION is not set # CONFIG_SGI_PARTITION is not set # CONFIG_ULTRIX_PARTITION is not set -CONFIG_SUN_PARTITION=y +# CONFIG_SUN_PARTITION is not set # CONFIG_KARMA_PARTITION is not set # CONFIG_EFI_PARTITION is not set # CONFIG_SYSV68_PARTITION is not set @@ -1300,15 +1309,48 @@ CONFIG_NLS_ISO8859_2=y # CONFIG_PRINTK_TIME is not set CONFIG_ENABLE_WARN_DEPRECATED=y CONFIG_ENABLE_MUST_CHECK=y -# CONFIG_MAGIC_SYSRQ is not set +CONFIG_FRAME_WARN=1024 +CONFIG_MAGIC_SYSRQ=y # CONFIG_UNUSED_SYMBOLS is not set # CONFIG_DEBUG_FS is not set # CONFIG_HEADERS_CHECK is not set -# CONFIG_DEBUG_KERNEL is not set +CONFIG_DEBUG_KERNEL=y +# CONFIG_DEBUG_SHIRQ is not set +CONFIG_DETECT_SOFTLOCKUP=y +CONFIG_SCHED_DEBUG=y +CONFIG_SCHEDSTATS=y +# CONFIG_TIMER_STATS is not set +# CONFIG_DEBUG_OBJECTS is not set +CONFIG_DEBUG_PREEMPT=y +# CONFIG_DEBUG_RT_MUTEXES is not set +# CONFIG_RT_MUTEX_TESTER is not set +# CONFIG_DEBUG_SPINLOCK is not set +# CONFIG_DEBUG_MUTEXES is not set +# CONFIG_DEBUG_LOCK_ALLOC is not set +# CONFIG_PROVE_LOCKING is not set +# CONFIG_LOCK_STAT is not set +# CONFIG_DEBUG_SPINLOCK_SLEEP is not set +# CONFIG_DEBUG_LOCKING_API_SELFTESTS is not set +# CONFIG_DEBUG_KOBJECT is not set # CONFIG_DEBUG_BUGVERBOSE is not set +CONFIG_DEBUG_INFO=y +# CONFIG_DEBUG_VM is not set +# CONFIG_DEBUG_WRITECOUNT is not set +# CONFIG_DEBUG_LIST is not set +# CONFIG_DEBUG_SG is not set CONFIG_FRAME_POINTER=y +# CONFIG_BOOT_PRINTK_DELAY is not set +# CONFIG_RCU_TORTURE_TEST is not set +# CONFIG_KPROBES_SANITY_TEST is not set +# CONFIG_BACKTRACE_SELF_TEST is not set +# CONFIG_LKDTM is not set +# CONFIG_FAULT_INJECTION is not set # CONFIG_SAMPLES is not set CONFIG_DEBUG_USER=y +CONFIG_DEBUG_ERRORS=y +# CONFIG_DEBUG_STACK_USAGE is not set +CONFIG_DEBUG_LL=y +# CONFIG_DEBUG_ICEDCC is not set # # Security options @@ -1317,50 +1359,79 @@ CONFIG_DEBUG_USER=y # CONFIG_SECURITY is not set # CONFIG_SECURITY_FILE_CAPABILITIES is not set CONFIG_CRYPTO=y + +# +# Crypto core or helper +# CONFIG_CRYPTO_ALGAPI=m CONFIG_CRYPTO_BLKCIPHER=m -# CONFIG_CRYPTO_SEQIV is not set CONFIG_CRYPTO_MANAGER=m +# CONFIG_CRYPTO_GF128MUL is not set +# CONFIG_CRYPTO_NULL is not set +# CONFIG_CRYPTO_CRYPTD is not set +# CONFIG_CRYPTO_AUTHENC is not set +# CONFIG_CRYPTO_TEST is not set + +# +# Authenticated Encryption with Associated Data +# +# CONFIG_CRYPTO_CCM is not set +# CONFIG_CRYPTO_GCM is not set +# CONFIG_CRYPTO_SEQIV is not set + +# +# Block modes +# +CONFIG_CRYPTO_CBC=m +# CONFIG_CRYPTO_CTR is not set +# CONFIG_CRYPTO_CTS is not set +CONFIG_CRYPTO_ECB=m +# CONFIG_CRYPTO_LRW is not set +CONFIG_CRYPTO_PCBC=m +# CONFIG_CRYPTO_XTS is not set + +# +# Hash modes +# # CONFIG_CRYPTO_HMAC is not set # CONFIG_CRYPTO_XCBC is not set -# CONFIG_CRYPTO_NULL is not set + +# +# Digest +# +# CONFIG_CRYPTO_CRC32C is not set # CONFIG_CRYPTO_MD4 is not set # CONFIG_CRYPTO_MD5 is not set +# CONFIG_CRYPTO_MICHAEL_MIC is not set # CONFIG_CRYPTO_SHA1 is not set # CONFIG_CRYPTO_SHA256 is not set # CONFIG_CRYPTO_SHA512 is not set -# CONFIG_CRYPTO_WP512 is not set # CONFIG_CRYPTO_TGR192 is not set -# CONFIG_CRYPTO_GF128MUL is not set -CONFIG_CRYPTO_ECB=m -CONFIG_CRYPTO_CBC=m -CONFIG_CRYPTO_PCBC=m -# CONFIG_CRYPTO_LRW is not set -# CONFIG_CRYPTO_XTS is not set -# CONFIG_CRYPTO_CTR is not set -# CONFIG_CRYPTO_GCM is not set -# CONFIG_CRYPTO_CCM is not set -# CONFIG_CRYPTO_CRYPTD is not set -# CONFIG_CRYPTO_DES is not set -# CONFIG_CRYPTO_FCRYPT is not set -# CONFIG_CRYPTO_BLOWFISH is not set -# CONFIG_CRYPTO_TWOFISH is not set -# CONFIG_CRYPTO_SERPENT is not set +# CONFIG_CRYPTO_WP512 is not set + +# +# Ciphers +# # CONFIG_CRYPTO_AES is not set +# CONFIG_CRYPTO_ANUBIS is not set +# CONFIG_CRYPTO_ARC4 is not set +# CONFIG_CRYPTO_BLOWFISH is not set +# CONFIG_CRYPTO_CAMELLIA is not set # CONFIG_CRYPTO_CAST5 is not set # CONFIG_CRYPTO_CAST6 is not set -# CONFIG_CRYPTO_TEA is not set -# CONFIG_CRYPTO_ARC4 is not set +# CONFIG_CRYPTO_DES is not set +# CONFIG_CRYPTO_FCRYPT is not set # CONFIG_CRYPTO_KHAZAD is not set -# CONFIG_CRYPTO_ANUBIS is not set -# CONFIG_CRYPTO_SEED is not set # CONFIG_CRYPTO_SALSA20 is not set +# CONFIG_CRYPTO_SEED is not set +# CONFIG_CRYPTO_SERPENT is not set +# CONFIG_CRYPTO_TEA is not set +# CONFIG_CRYPTO_TWOFISH is not set + +# +# Compression +# # CONFIG_CRYPTO_DEFLATE is not set -# CONFIG_CRYPTO_MICHAEL_MIC is not set -# CONFIG_CRYPTO_CRC32C is not set -# CONFIG_CRYPTO_CAMELLIA is not set -# CONFIG_CRYPTO_TEST is not set -# CONFIG_CRYPTO_AUTHENC is not set # CONFIG_CRYPTO_LZO is not set CONFIG_CRYPTO_HW=y # CONFIG_CRYPTO_DEV_HIFN_795X is not set @@ -1369,12 +1440,14 @@ CONFIG_CRYPTO_HW=y # Library routines # CONFIG_BITREVERSE=y -CONFIG_CRC_CCITT=y -CONFIG_CRC16=y -# CONFIG_CRC_ITU_T is not set +# CONFIG_GENERIC_FIND_FIRST_BIT is not set +# CONFIG_GENERIC_FIND_NEXT_BIT is not set +# CONFIG_CRC_CCITT is not set +# CONFIG_CRC16 is not set +CONFIG_CRC_ITU_T=m CONFIG_CRC32=y # CONFIG_CRC7 is not set -CONFIG_LIBCRC32C=y +# CONFIG_LIBCRC32C is not set CONFIG_ZLIB_INFLATE=y CONFIG_ZLIB_DEFLATE=y CONFIG_PLIST=y diff --git a/arch/arm/configs/picotux200_defconfig b/arch/arm/configs/picotux200_defconfig index 95a22f51280..14826f0dabd 100644 --- a/arch/arm/configs/picotux200_defconfig +++ b/arch/arm/configs/picotux200_defconfig @@ -201,7 +201,6 @@ CONFIG_ARM_THUMB=y # Kernel Features # # CONFIG_PREEMPT is not set -CONFIG_NO_IDLE_HZ=y CONFIG_HZ=100 CONFIG_AEABI=y CONFIG_OABI_COMPAT=y diff --git a/arch/arm/configs/pnx4008_defconfig b/arch/arm/configs/pnx4008_defconfig index b5e11aa2e29..811b8f60d19 100644 --- a/arch/arm/configs/pnx4008_defconfig +++ b/arch/arm/configs/pnx4008_defconfig @@ -151,7 +151,6 @@ CONFIG_ARM_THUMB=y # Kernel Features # CONFIG_PREEMPT=y -# CONFIG_NO_IDLE_HZ is not set CONFIG_HZ=100 # CONFIG_AEABI is not set # CONFIG_ARCH_DISCONTIGMEM_ENABLE is not set diff --git a/arch/arm/configs/qil-a9260_defconfig b/arch/arm/configs/qil-a9260_defconfig new file mode 100644 index 00000000000..ef903bed061 --- /dev/null +++ b/arch/arm/configs/qil-a9260_defconfig @@ -0,0 +1,1256 @@ +# +# Automatically generated make config: don't edit +# Linux kernel version: 2.6.24 +# Tue Apr 15 12:28:38 2008 +# +CONFIG_ARM=y +CONFIG_SYS_SUPPORTS_APM_EMULATION=y +CONFIG_GENERIC_GPIO=y +CONFIG_GENERIC_TIME=y +CONFIG_GENERIC_CLOCKEVENTS=y +CONFIG_MMU=y +# CONFIG_NO_IOPORT is not set +CONFIG_GENERIC_HARDIRQS=y +CONFIG_STACKTRACE_SUPPORT=y +CONFIG_LOCKDEP_SUPPORT=y +CONFIG_TRACE_IRQFLAGS_SUPPORT=y +CONFIG_HARDIRQS_SW_RESEND=y +CONFIG_GENERIC_IRQ_PROBE=y +CONFIG_RWSEM_GENERIC_SPINLOCK=y +# CONFIG_ARCH_HAS_ILOG2_U32 is not set +# CONFIG_ARCH_HAS_ILOG2_U64 is not set +CONFIG_GENERIC_HWEIGHT=y +CONFIG_GENERIC_CALIBRATE_DELAY=y +CONFIG_ZONE_DMA=y +CONFIG_VECTORS_BASE=0xffff0000 +CONFIG_DEFCONFIG_LIST="/lib/modules/$UNAME_RELEASE/.config" + +# +# General setup +# +CONFIG_EXPERIMENTAL=y +CONFIG_BROKEN_ON_SMP=y +CONFIG_INIT_ENV_ARG_LIMIT=32 +CONFIG_LOCALVERSION="" +# CONFIG_LOCALVERSION_AUTO is not set +# CONFIG_SWAP is not set +CONFIG_SYSVIPC=y +CONFIG_SYSVIPC_SYSCTL=y +# CONFIG_POSIX_MQUEUE is not set +# CONFIG_BSD_PROCESS_ACCT is not set +# CONFIG_TASKSTATS is not set +# CONFIG_USER_NS is not set +# CONFIG_PID_NS is not set +# CONFIG_AUDIT is not set +# CONFIG_IKCONFIG is not set +CONFIG_LOG_BUF_SHIFT=14 +# CONFIG_CGROUPS is not set +CONFIG_FAIR_GROUP_SCHED=y +CONFIG_FAIR_USER_SCHED=y +# CONFIG_FAIR_CGROUP_SCHED is not set +# CONFIG_SYSFS_DEPRECATED is not set +# CONFIG_RELAY is not set +# CONFIG_BLK_DEV_INITRD is not set +# CONFIG_CC_OPTIMIZE_FOR_SIZE is not set +CONFIG_SYSCTL=y +# CONFIG_EMBEDDED is not set +CONFIG_UID16=y +CONFIG_SYSCTL_SYSCALL=y +CONFIG_KALLSYMS=y +# CONFIG_KALLSYMS_ALL is not set +# CONFIG_KALLSYMS_EXTRA_PASS is not set +CONFIG_HOTPLUG=y +CONFIG_PRINTK=y +CONFIG_BUG=y +CONFIG_ELF_CORE=y +CONFIG_BASE_FULL=y +CONFIG_FUTEX=y +CONFIG_ANON_INODES=y +CONFIG_EPOLL=y +CONFIG_SIGNALFD=y +CONFIG_EVENTFD=y +CONFIG_SHMEM=y +CONFIG_VM_EVENT_COUNTERS=y +CONFIG_SLAB=y +# CONFIG_SLUB is not set +# CONFIG_SLOB is not set +CONFIG_SLABINFO=y +CONFIG_RT_MUTEXES=y +# CONFIG_TINY_SHMEM is not set +CONFIG_BASE_SMALL=0 +CONFIG_MODULES=y +CONFIG_MODULE_UNLOAD=y +# CONFIG_MODULE_FORCE_UNLOAD is not set +# CONFIG_MODVERSIONS is not set +# CONFIG_MODULE_SRCVERSION_ALL is not set +CONFIG_KMOD=y +CONFIG_BLOCK=y +# CONFIG_LBD is not set +# CONFIG_BLK_DEV_IO_TRACE is not set +# CONFIG_LSF is not set +# CONFIG_BLK_DEV_BSG is not set + +# +# IO Schedulers +# +CONFIG_IOSCHED_NOOP=y +CONFIG_IOSCHED_AS=y +# CONFIG_IOSCHED_DEADLINE is not set +# CONFIG_IOSCHED_CFQ is not set +CONFIG_DEFAULT_AS=y +# CONFIG_DEFAULT_DEADLINE is not set +# CONFIG_DEFAULT_CFQ is not set +# CONFIG_DEFAULT_NOOP is not set +CONFIG_DEFAULT_IOSCHED="anticipatory" + +# +# System Type +# +# CONFIG_ARCH_AAEC2000 is not set +# CONFIG_ARCH_INTEGRATOR is not set +# CONFIG_ARCH_REALVIEW is not set +# CONFIG_ARCH_VERSATILE is not set +CONFIG_ARCH_AT91=y +# CONFIG_ARCH_CLPS7500 is not set +# CONFIG_ARCH_CLPS711X is not set +# CONFIG_ARCH_CO285 is not set +# CONFIG_ARCH_EBSA110 is not set +# CONFIG_ARCH_EP93XX is not set +# CONFIG_ARCH_FOOTBRIDGE is not set +# CONFIG_ARCH_NETX is not set +# CONFIG_ARCH_H720X is not set +# CONFIG_ARCH_IMX is not set +# CONFIG_ARCH_IOP13XX is not set +# CONFIG_ARCH_IOP32X is not set +# CONFIG_ARCH_IOP33X is not set +# CONFIG_ARCH_IXP23XX is not set +# CONFIG_ARCH_IXP2000 is not set +# CONFIG_ARCH_IXP4XX is not set +# CONFIG_ARCH_L7200 is not set +# CONFIG_ARCH_KS8695 is not set +# CONFIG_ARCH_NS9XXX is not set +# CONFIG_ARCH_MXC is not set +# CONFIG_ARCH_PNX4008 is not set +# CONFIG_ARCH_PXA is not set +# CONFIG_ARCH_RPC is not set +# CONFIG_ARCH_SA1100 is not set +# CONFIG_ARCH_S3C2410 is not set +# CONFIG_ARCH_SHARK is not set +# CONFIG_ARCH_LH7A40X is not set +# CONFIG_ARCH_DAVINCI is not set +# CONFIG_ARCH_OMAP is not set + +# +# Boot options +# + +# +# Power management +# + +# +# Atmel AT91 System-on-Chip +# +# CONFIG_ARCH_AT91RM9200 is not set +CONFIG_ARCH_AT91SAM9260=y +# CONFIG_ARCH_AT91SAM9261 is not set +# CONFIG_ARCH_AT91SAM9263 is not set +# CONFIG_ARCH_AT91SAM9RL is not set +# CONFIG_ARCH_AT91CAP9 is not set +# CONFIG_ARCH_AT91X40 is not set +CONFIG_AT91_PMC_UNIT=y + +# +# AT91SAM9260 Variants +# +# CONFIG_ARCH_AT91SAM9260_SAM9XE is not set + +# +# AT91SAM9260 / AT91SAM9XE Board Type +# +# CONFIG_MACH_AT91SAM9260EK is not set +# CONFIG_MACH_CAM60 is not set +# CONFIG_MACH_SAM9_L9260 is not set +# CONFIG_MACH_USB_A9260 is not set +CONFIG_MACH_QIL_A9260=y + +# +# AT91 Board Options +# + +# +# AT91 Feature Selections +# +# CONFIG_AT91_PROGRAMMABLE_CLOCKS is not set +CONFIG_AT91_SLOW_CLOCK=y +CONFIG_AT91_TIMER_HZ=100 +# CONFIG_AT91_EARLY_DBGU is not set +CONFIG_AT91_EARLY_USART0=y +# CONFIG_AT91_EARLY_USART1 is not set +# CONFIG_AT91_EARLY_USART2 is not set +# CONFIG_AT91_EARLY_USART3 is not set +# CONFIG_AT91_EARLY_USART4 is not set +# CONFIG_AT91_EARLY_USART5 is not set + +# +# Processor Type +# +CONFIG_CPU_32=y +CONFIG_CPU_ARM926T=y +CONFIG_CPU_32v5=y +CONFIG_CPU_ABRT_EV5TJ=y +CONFIG_CPU_CACHE_VIVT=y +CONFIG_CPU_COPY_V4WB=y +CONFIG_CPU_TLB_V4WBI=y +CONFIG_CPU_CP15=y +CONFIG_CPU_CP15_MMU=y + +# +# Processor Features +# +# CONFIG_ARM_THUMB is not set +# CONFIG_CPU_ICACHE_DISABLE is not set +# CONFIG_CPU_DCACHE_DISABLE is not set +# CONFIG_CPU_DCACHE_WRITETHROUGH is not set +# CONFIG_CPU_CACHE_ROUND_ROBIN is not set +# CONFIG_OUTER_CACHE is not set + +# +# Bus support +# +# CONFIG_PCI_SYSCALL is not set +# CONFIG_ARCH_SUPPORTS_MSI is not set +# CONFIG_PCCARD is not set + +# +# Kernel Features +# +# CONFIG_TICK_ONESHOT is not set +# CONFIG_NO_HZ is not set +# CONFIG_HIGH_RES_TIMERS is not set +CONFIG_GENERIC_CLOCKEVENTS_BUILD=y +# CONFIG_PREEMPT is not set +CONFIG_HZ=100 +CONFIG_AEABI=y +CONFIG_OABI_COMPAT=y +# CONFIG_ARCH_DISCONTIGMEM_ENABLE is not set +CONFIG_SELECT_MEMORY_MODEL=y +CONFIG_FLATMEM_MANUAL=y +# CONFIG_DISCONTIGMEM_MANUAL is not set +# CONFIG_SPARSEMEM_MANUAL is not set +CONFIG_FLATMEM=y +CONFIG_FLAT_NODE_MEM_MAP=y +# CONFIG_SPARSEMEM_STATIC is not set +# CONFIG_SPARSEMEM_VMEMMAP_ENABLE is not set +CONFIG_SPLIT_PTLOCK_CPUS=4096 +# CONFIG_RESOURCES_64BIT is not set +CONFIG_ZONE_DMA_FLAG=1 +CONFIG_BOUNCE=y +CONFIG_VIRT_TO_BUS=y +# CONFIG_LEDS is not set +CONFIG_ALIGNMENT_TRAP=y + +# +# Boot options +# +CONFIG_ZBOOT_ROM_TEXT=0x0 +CONFIG_ZBOOT_ROM_BSS=0x0 +CONFIG_CMDLINE="mem=64M console=ttyS1,115200" +# CONFIG_XIP_KERNEL is not set +# CONFIG_KEXEC is not set + +# +# Floating point emulation +# + +# +# At least one emulation must be selected +# +CONFIG_FPE_NWFPE=y +# CONFIG_FPE_NWFPE_XP is not set +# CONFIG_FPE_FASTFPE is not set +# CONFIG_VFP is not set + +# +# Userspace binary formats +# +CONFIG_BINFMT_ELF=y +# CONFIG_BINFMT_AOUT is not set +# CONFIG_BINFMT_MISC is not set + +# +# Power management options +# +CONFIG_PM=y +# CONFIG_PM_LEGACY is not set +# CONFIG_PM_DEBUG is not set +CONFIG_PM_SLEEP=y +CONFIG_SUSPEND_UP_POSSIBLE=y +CONFIG_SUSPEND=y +# CONFIG_APM_EMULATION is not set + +# +# Networking +# +CONFIG_NET=y + +# +# Networking options +# +CONFIG_PACKET=y +# CONFIG_PACKET_MMAP is not set +CONFIG_UNIX=y +# CONFIG_NET_KEY is not set +CONFIG_INET=y +CONFIG_IP_MULTICAST=y +CONFIG_IP_ADVANCED_ROUTER=y +CONFIG_ASK_IP_FIB_HASH=y +# CONFIG_IP_FIB_TRIE is not set +CONFIG_IP_FIB_HASH=y +# CONFIG_IP_MULTIPLE_TABLES is not set +# CONFIG_IP_ROUTE_MULTIPATH is not set +CONFIG_IP_ROUTE_VERBOSE=y +CONFIG_IP_PNP=y +# CONFIG_IP_PNP_DHCP is not set +CONFIG_IP_PNP_BOOTP=y +CONFIG_IP_PNP_RARP=y +# CONFIG_NET_IPIP is not set +# CONFIG_NET_IPGRE is not set +CONFIG_IP_MROUTE=y +CONFIG_IP_PIMSM_V1=y +CONFIG_IP_PIMSM_V2=y +# CONFIG_ARPD is not set +# CONFIG_SYN_COOKIES is not set +# CONFIG_INET_AH is not set +# CONFIG_INET_ESP is not set +# CONFIG_INET_IPCOMP is not set +# CONFIG_INET_XFRM_TUNNEL is not set +# CONFIG_INET_TUNNEL is not set +# CONFIG_INET_XFRM_MODE_TRANSPORT is not set +# CONFIG_INET_XFRM_MODE_TUNNEL is not set +# CONFIG_INET_XFRM_MODE_BEET is not set +# CONFIG_INET_LRO is not set +# CONFIG_INET_DIAG is not set +# CONFIG_TCP_CONG_ADVANCED is not set +CONFIG_TCP_CONG_CUBIC=y +CONFIG_DEFAULT_TCP_CONG="cubic" +# CONFIG_TCP_MD5SIG is not set +# CONFIG_IPV6 is not set +# CONFIG_INET6_XFRM_TUNNEL is not set +# CONFIG_INET6_TUNNEL is not set +# CONFIG_NETWORK_SECMARK is not set +# CONFIG_NETFILTER is not set +# CONFIG_IP_DCCP is not set +# CONFIG_IP_SCTP is not set +# CONFIG_TIPC is not set +# CONFIG_ATM is not set +# CONFIG_BRIDGE is not set +# CONFIG_VLAN_8021Q is not set +# CONFIG_DECNET is not set +# CONFIG_LLC2 is not set +# CONFIG_IPX is not set +# CONFIG_ATALK is not set +# CONFIG_X25 is not set +# CONFIG_LAPB is not set +# CONFIG_ECONET is not set +# CONFIG_WAN_ROUTER is not set +# CONFIG_NET_SCHED is not set + +# +# Network testing +# +# CONFIG_NET_PKTGEN is not set +# CONFIG_HAMRADIO is not set +# CONFIG_IRDA is not set +# CONFIG_BT is not set +# CONFIG_AF_RXRPC is not set + +# +# Wireless +# +# CONFIG_CFG80211 is not set +# CONFIG_WIRELESS_EXT is not set +# CONFIG_MAC80211 is not set +# CONFIG_IEEE80211 is not set +# CONFIG_RFKILL is not set +# CONFIG_NET_9P is not set + +# +# Device Drivers +# + +# +# Generic Driver Options +# +CONFIG_UEVENT_HELPER_PATH="/sbin/hotplug" +CONFIG_STANDALONE=y +CONFIG_PREVENT_FIRMWARE_BUILD=y +# CONFIG_FW_LOADER is not set +# CONFIG_DEBUG_DRIVER is not set +# CONFIG_DEBUG_DEVRES is not set +# CONFIG_SYS_HYPERVISOR is not set +# CONFIG_CONNECTOR is not set +CONFIG_MTD=y +# CONFIG_MTD_DEBUG is not set +# CONFIG_MTD_CONCAT is not set +CONFIG_MTD_PARTITIONS=y +# CONFIG_MTD_REDBOOT_PARTS is not set +CONFIG_MTD_CMDLINE_PARTS=y +# CONFIG_MTD_AFS_PARTS is not set + +# +# User Modules And Translation Layers +# +CONFIG_MTD_CHAR=y +CONFIG_MTD_BLKDEVS=y +CONFIG_MTD_BLOCK=y +# CONFIG_FTL is not set +# CONFIG_NFTL is not set +# CONFIG_INFTL is not set +# CONFIG_RFD_FTL is not set +# CONFIG_SSFDC is not set +# CONFIG_MTD_OOPS is not set + +# +# RAM/ROM/Flash chip drivers +# +# CONFIG_MTD_CFI is not set +# CONFIG_MTD_JEDECPROBE is not set +CONFIG_MTD_MAP_BANK_WIDTH_1=y +CONFIG_MTD_MAP_BANK_WIDTH_2=y +CONFIG_MTD_MAP_BANK_WIDTH_4=y +# CONFIG_MTD_MAP_BANK_WIDTH_8 is not set +# CONFIG_MTD_MAP_BANK_WIDTH_16 is not set +# CONFIG_MTD_MAP_BANK_WIDTH_32 is not set +CONFIG_MTD_CFI_I1=y +CONFIG_MTD_CFI_I2=y +# CONFIG_MTD_CFI_I4 is not set +# CONFIG_MTD_CFI_I8 is not set +# CONFIG_MTD_RAM is not set +# CONFIG_MTD_ROM is not set +# CONFIG_MTD_ABSENT is not set + +# +# Mapping drivers for chip access +# +# CONFIG_MTD_COMPLEX_MAPPINGS is not set +# CONFIG_MTD_PLATRAM is not set + +# +# Self-contained MTD device drivers +# +CONFIG_MTD_DATAFLASH=y +# CONFIG_MTD_M25P80 is not set +# CONFIG_MTD_SLRAM is not set +# CONFIG_MTD_PHRAM is not set +# CONFIG_MTD_MTDRAM is not set +# CONFIG_MTD_BLOCK2MTD is not set + +# +# Disk-On-Chip Device Drivers +# +# CONFIG_MTD_DOC2000 is not set +# CONFIG_MTD_DOC2001 is not set +# CONFIG_MTD_DOC2001PLUS is not set +CONFIG_MTD_NAND=y +# CONFIG_MTD_NAND_VERIFY_WRITE is not set +# CONFIG_MTD_NAND_ECC_SMC is not set +# CONFIG_MTD_NAND_MUSEUM_IDS is not set +CONFIG_MTD_NAND_IDS=y +# CONFIG_MTD_NAND_DISKONCHIP is not set +CONFIG_MTD_NAND_AT91=y +CONFIG_MTD_NAND_AT91_ECC_SOFT=y +# CONFIG_MTD_NAND_AT91_ECC_HW is not set +# CONFIG_MTD_NAND_AT91_ECC_NONE is not set +# CONFIG_MTD_NAND_NANDSIM is not set +# CONFIG_MTD_NAND_PLATFORM is not set +# CONFIG_MTD_ALAUDA is not set +# CONFIG_MTD_ONENAND is not set + +# +# UBI - Unsorted block images +# +# CONFIG_MTD_UBI is not set +# CONFIG_PARPORT is not set +CONFIG_BLK_DEV=y +# CONFIG_BLK_DEV_COW_COMMON is not set +CONFIG_BLK_DEV_LOOP=y +# CONFIG_BLK_DEV_CRYPTOLOOP is not set +# CONFIG_BLK_DEV_NBD is not set +# CONFIG_BLK_DEV_UB is not set +# CONFIG_BLK_DEV_RAM is not set +# CONFIG_CDROM_PKTCDVD is not set +# CONFIG_ATA_OVER_ETH is not set +# CONFIG_MISC_DEVICES is not set + +# +# SCSI device support +# +# CONFIG_RAID_ATTRS is not set +CONFIG_SCSI=y +CONFIG_SCSI_DMA=y +# CONFIG_SCSI_TGT is not set +# CONFIG_SCSI_NETLINK is not set +CONFIG_SCSI_PROC_FS=y + +# +# SCSI support type (disk, tape, CD-ROM) +# +CONFIG_BLK_DEV_SD=y +# CONFIG_CHR_DEV_ST is not set +# CONFIG_CHR_DEV_OSST is not set +# CONFIG_BLK_DEV_SR is not set +# CONFIG_CHR_DEV_SG is not set +# CONFIG_CHR_DEV_SCH is not set + +# +# Some SCSI devices (e.g. CD jukebox) support multiple LUNs +# +CONFIG_SCSI_MULTI_LUN=y +# CONFIG_SCSI_CONSTANTS is not set +# CONFIG_SCSI_LOGGING is not set +# CONFIG_SCSI_SCAN_ASYNC is not set +CONFIG_SCSI_WAIT_SCAN=m + +# +# SCSI Transports +# +# CONFIG_SCSI_SPI_ATTRS is not set +# CONFIG_SCSI_FC_ATTRS is not set +# CONFIG_SCSI_ISCSI_ATTRS is not set +# CONFIG_SCSI_SAS_LIBSAS is not set +# CONFIG_SCSI_SRP_ATTRS is not set +CONFIG_SCSI_LOWLEVEL=y +# CONFIG_ISCSI_TCP is not set +# CONFIG_SCSI_DEBUG is not set +# CONFIG_ATA is not set +# CONFIG_MD is not set +CONFIG_NETDEVICES=y +# CONFIG_NETDEVICES_MULTIQUEUE is not set +# CONFIG_DUMMY is not set +# CONFIG_BONDING is not set +# CONFIG_MACVLAN is not set +# CONFIG_EQUALIZER is not set +# CONFIG_TUN is not set +# CONFIG_VETH is not set +CONFIG_PHYLIB=y + +# +# MII PHY device drivers +# +# CONFIG_MARVELL_PHY is not set +# CONFIG_DAVICOM_PHY is not set +# CONFIG_QSEMI_PHY is not set +# CONFIG_LXT_PHY is not set +# CONFIG_CICADA_PHY is not set +# CONFIG_VITESSE_PHY is not set +# CONFIG_SMSC_PHY is not set +# CONFIG_BROADCOM_PHY is not set +# CONFIG_ICPLUS_PHY is not set +# CONFIG_FIXED_PHY is not set +# CONFIG_MDIO_BITBANG is not set +CONFIG_NET_ETHERNET=y +CONFIG_MII=y +CONFIG_MACB=y +# CONFIG_AX88796 is not set +# CONFIG_SMC91X is not set +# CONFIG_DM9000 is not set +# CONFIG_IBM_NEW_EMAC_ZMII is not set +# CONFIG_IBM_NEW_EMAC_RGMII is not set +# CONFIG_IBM_NEW_EMAC_TAH is not set +# CONFIG_IBM_NEW_EMAC_EMAC4 is not set +# CONFIG_B44 is not set +CONFIG_NETDEV_1000=y +CONFIG_NETDEV_10000=y + +# +# Wireless LAN +# +# CONFIG_WLAN_PRE80211 is not set +# CONFIG_WLAN_80211 is not set + +# +# USB Network Adapters +# +# CONFIG_USB_CATC is not set +# CONFIG_USB_KAWETH is not set +# CONFIG_USB_PEGASUS is not set +# CONFIG_USB_RTL8150 is not set +# CONFIG_USB_USBNET is not set +# CONFIG_WAN is not set +# CONFIG_PPP is not set +# CONFIG_SLIP is not set +# CONFIG_SHAPER is not set +# CONFIG_NETCONSOLE is not set +# CONFIG_NETPOLL is not set +# CONFIG_NET_POLL_CONTROLLER is not set +# CONFIG_ISDN is not set + +# +# Input device support +# +CONFIG_INPUT=y +# CONFIG_INPUT_FF_MEMLESS is not set +# CONFIG_INPUT_POLLDEV is not set + +# +# Userland interfaces +# +CONFIG_INPUT_MOUSEDEV=y +# CONFIG_INPUT_MOUSEDEV_PSAUX is not set +CONFIG_INPUT_MOUSEDEV_SCREEN_X=1024 +CONFIG_INPUT_MOUSEDEV_SCREEN_Y=768 +# CONFIG_INPUT_JOYDEV is not set +CONFIG_INPUT_EVDEV=y +CONFIG_INPUT_EVBUG=y + +# +# Input Device Drivers +# +CONFIG_INPUT_KEYBOARD=y +# CONFIG_KEYBOARD_ATKBD is not set +# CONFIG_KEYBOARD_SUNKBD is not set +# CONFIG_KEYBOARD_LKKBD is not set +# CONFIG_KEYBOARD_XTKBD is not set +# CONFIG_KEYBOARD_NEWTON is not set +# CONFIG_KEYBOARD_STOWAWAY is not set +CONFIG_KEYBOARD_GPIO=y +# CONFIG_INPUT_MOUSE is not set +# CONFIG_INPUT_JOYSTICK is not set +# CONFIG_INPUT_TABLET is not set +# CONFIG_INPUT_TOUCHSCREEN is not set +# CONFIG_INPUT_MISC is not set + +# +# Hardware I/O ports +# +# CONFIG_SERIO is not set +# CONFIG_GAMEPORT is not set + +# +# Character devices +# +CONFIG_VT=y +CONFIG_VT_CONSOLE=y +CONFIG_HW_CONSOLE=y +# CONFIG_VT_HW_CONSOLE_BINDING is not set +# CONFIG_SERIAL_NONSTANDARD is not set + +# +# Serial drivers +# +# CONFIG_SERIAL_8250 is not set + +# +# Non-8250 serial port support +# +CONFIG_SERIAL_ATMEL=y +CONFIG_SERIAL_ATMEL_CONSOLE=y +# CONFIG_SERIAL_ATMEL_TTYAT is not set +CONFIG_SERIAL_CORE=y +CONFIG_SERIAL_CORE_CONSOLE=y +CONFIG_UNIX98_PTYS=y +CONFIG_LEGACY_PTYS=y +CONFIG_LEGACY_PTY_COUNT=256 +# CONFIG_IPMI_HANDLER is not set +CONFIG_HW_RANDOM=y +# CONFIG_NVRAM is not set +# CONFIG_R3964 is not set +# CONFIG_RAW_DRIVER is not set +# CONFIG_TCG_TPM is not set +CONFIG_I2C=y +CONFIG_I2C_BOARDINFO=y +CONFIG_I2C_CHARDEV=y + +# +# I2C Algorithms +# +# CONFIG_I2C_ALGOBIT is not set +# CONFIG_I2C_ALGOPCF is not set +# CONFIG_I2C_ALGOPCA is not set + +# +# I2C Hardware Bus support +# +# CONFIG_I2C_GPIO is not set +# CONFIG_I2C_OCORES is not set +# CONFIG_I2C_PARPORT_LIGHT is not set +# CONFIG_I2C_SIMTEC is not set +# CONFIG_I2C_TAOS_EVM is not set +# CONFIG_I2C_STUB is not set +# CONFIG_I2C_TINY_USB is not set +# CONFIG_I2C_PCA is not set + +# +# Miscellaneous I2C Chip support +# +# CONFIG_SENSORS_DS1337 is not set +# CONFIG_SENSORS_DS1374 is not set +# CONFIG_DS1682 is not set +# CONFIG_SENSORS_EEPROM is not set +# CONFIG_SENSORS_PCF8574 is not set +# CONFIG_SENSORS_PCA9539 is not set +# CONFIG_SENSORS_PCF8591 is not set +# CONFIG_SENSORS_MAX6875 is not set +# CONFIG_SENSORS_TSL2550 is not set +# CONFIG_I2C_DEBUG_CORE is not set +# CONFIG_I2C_DEBUG_ALGO is not set +# CONFIG_I2C_DEBUG_BUS is not set +# CONFIG_I2C_DEBUG_CHIP is not set + +# +# SPI support +# +CONFIG_SPI=y +# CONFIG_SPI_DEBUG is not set +CONFIG_SPI_MASTER=y + +# +# SPI Master Controller Drivers +# +CONFIG_SPI_ATMEL=y +# CONFIG_SPI_BITBANG is not set + +# +# SPI Protocol Masters +# +# CONFIG_SPI_AT25 is not set +# CONFIG_SPI_SPIDEV is not set +# CONFIG_SPI_TLE62X0 is not set +# CONFIG_W1 is not set +# CONFIG_POWER_SUPPLY is not set +# CONFIG_HWMON is not set +CONFIG_WATCHDOG=y +CONFIG_WATCHDOG_NOWAYOUT=y + +# +# Watchdog Device Drivers +# +# CONFIG_SOFT_WATCHDOG is not set +# CONFIG_AT91SAM9_WATCHDOG is not set + +# +# USB-based Watchdog Cards +# +# CONFIG_USBPCWATCHDOG is not set + +# +# Sonics Silicon Backplane +# +CONFIG_SSB_POSSIBLE=y +# CONFIG_SSB is not set + +# +# Multifunction device drivers +# +# CONFIG_MFD_SM501 is not set + +# +# Multimedia devices +# +# CONFIG_VIDEO_DEV is not set +# CONFIG_DVB_CORE is not set +# CONFIG_DAB is not set + +# +# Graphics support +# +# CONFIG_VGASTATE is not set +# CONFIG_VIDEO_OUTPUT_CONTROL is not set +# CONFIG_FB is not set +# CONFIG_BACKLIGHT_LCD_SUPPORT is not set + +# +# Display device support +# +# CONFIG_DISPLAY_SUPPORT is not set + +# +# Console display driver support +# +# CONFIG_VGA_CONSOLE is not set +CONFIG_DUMMY_CONSOLE=y + +# +# Sound +# +# CONFIG_SOUND is not set +CONFIG_HID_SUPPORT=y +CONFIG_HID=y +# CONFIG_HID_DEBUG is not set +# CONFIG_HIDRAW is not set + +# +# USB Input Devices +# +# CONFIG_USB_HID is not set + +# +# USB HID Boot Protocol drivers +# +# CONFIG_USB_KBD is not set +# CONFIG_USB_MOUSE is not set +CONFIG_USB_SUPPORT=y +CONFIG_USB_ARCH_HAS_HCD=y +CONFIG_USB_ARCH_HAS_OHCI=y +# CONFIG_USB_ARCH_HAS_EHCI is not set +CONFIG_USB=y +# CONFIG_USB_DEBUG is not set + +# +# Miscellaneous USB options +# +CONFIG_USB_DEVICEFS=y +CONFIG_USB_DEVICE_CLASS=y +# CONFIG_USB_DYNAMIC_MINORS is not set +# CONFIG_USB_SUSPEND is not set +# CONFIG_USB_PERSIST is not set +# CONFIG_USB_OTG is not set + +# +# USB Host Controller Drivers +# +# CONFIG_USB_ISP116X_HCD is not set +CONFIG_USB_OHCI_HCD=y +# CONFIG_USB_OHCI_BIG_ENDIAN_DESC is not set +# CONFIG_USB_OHCI_BIG_ENDIAN_MMIO is not set +CONFIG_USB_OHCI_LITTLE_ENDIAN=y +# CONFIG_USB_SL811_HCD is not set +# CONFIG_USB_R8A66597_HCD is not set + +# +# USB Device Class drivers +# +# CONFIG_USB_ACM is not set +# CONFIG_USB_PRINTER is not set + +# +# NOTE: USB_STORAGE enables SCSI, and 'SCSI disk support' +# + +# +# may also be needed; see USB_STORAGE Help for more information +# +CONFIG_USB_STORAGE=y +# CONFIG_USB_STORAGE_DEBUG is not set +# CONFIG_USB_STORAGE_DATAFAB is not set +# CONFIG_USB_STORAGE_FREECOM is not set +# CONFIG_USB_STORAGE_ISD200 is not set +# CONFIG_USB_STORAGE_DPCM is not set +# CONFIG_USB_STORAGE_USBAT is not set +# CONFIG_USB_STORAGE_SDDR09 is not set +# CONFIG_USB_STORAGE_SDDR55 is not set +# CONFIG_USB_STORAGE_JUMPSHOT is not set +# CONFIG_USB_STORAGE_ALAUDA is not set +# CONFIG_USB_STORAGE_KARMA is not set +# CONFIG_USB_LIBUSUAL is not set + +# +# USB Imaging devices +# +# CONFIG_USB_MDC800 is not set +# CONFIG_USB_MICROTEK is not set +CONFIG_USB_MON=y + +# +# USB port drivers +# + +# +# USB Serial Converter support +# +# CONFIG_USB_SERIAL is not set + +# +# USB Miscellaneous drivers +# +# CONFIG_USB_EMI62 is not set +# CONFIG_USB_EMI26 is not set +# CONFIG_USB_ADUTUX is not set +# CONFIG_USB_AUERSWALD is not set +# CONFIG_USB_RIO500 is not set +# CONFIG_USB_LEGOTOWER is not set +# CONFIG_USB_LCD is not set +# CONFIG_USB_BERRY_CHARGE is not set +# CONFIG_USB_LED is not set +# CONFIG_USB_CYPRESS_CY7C63 is not set +# CONFIG_USB_CYTHERM is not set +# CONFIG_USB_PHIDGET is not set +# CONFIG_USB_IDMOUSE is not set +# CONFIG_USB_FTDI_ELAN is not set +# CONFIG_USB_APPLEDISPLAY is not set +# CONFIG_USB_LD is not set +# CONFIG_USB_TRANCEVIBRATOR is not set +# CONFIG_USB_IOWARRIOR is not set +# CONFIG_USB_TEST is not set + +# +# USB DSL modem support +# + +# +# USB Gadget Support +# +CONFIG_USB_GADGET=y +# CONFIG_USB_GADGET_DEBUG is not set +# CONFIG_USB_GADGET_DEBUG_FILES is not set +CONFIG_USB_GADGET_SELECTED=y +# CONFIG_USB_GADGET_AMD5536UDC is not set +# CONFIG_USB_GADGET_ATMEL_USBA is not set +# CONFIG_USB_GADGET_FSL_USB2 is not set +# CONFIG_USB_GADGET_NET2280 is not set +# CONFIG_USB_GADGET_PXA2XX is not set +# CONFIG_USB_GADGET_M66592 is not set +# CONFIG_USB_GADGET_GOKU is not set +# CONFIG_USB_GADGET_LH7A40X is not set +# CONFIG_USB_GADGET_OMAP is not set +# CONFIG_USB_GADGET_S3C2410 is not set +CONFIG_USB_GADGET_AT91=y +CONFIG_USB_AT91=y +# CONFIG_USB_GADGET_DUMMY_HCD is not set +# CONFIG_USB_GADGET_DUALSPEED is not set +# CONFIG_USB_ZERO is not set +CONFIG_USB_ETH=y +CONFIG_USB_ETH_RNDIS=y +# CONFIG_USB_GADGETFS is not set +# CONFIG_USB_FILE_STORAGE is not set +# CONFIG_USB_G_SERIAL is not set +# CONFIG_USB_MIDI_GADGET is not set +CONFIG_MMC=y +# CONFIG_MMC_DEBUG is not set +# CONFIG_MMC_UNSAFE_RESUME is not set + +# +# MMC/SD Card Drivers +# +CONFIG_MMC_BLOCK=y +CONFIG_MMC_BLOCK_BOUNCE=y +# CONFIG_SDIO_UART is not set + +# +# MMC/SD Host Controller Drivers +# +CONFIG_MMC_AT91=y +# CONFIG_MMC_SPI is not set +CONFIG_NEW_LEDS=y +CONFIG_LEDS_CLASS=y + +# +# LED drivers +# +CONFIG_LEDS_GPIO=y + +# +# LED Triggers +# +CONFIG_LEDS_TRIGGERS=y +# CONFIG_LEDS_TRIGGER_TIMER is not set +CONFIG_LEDS_TRIGGER_HEARTBEAT=y +CONFIG_RTC_LIB=y +CONFIG_RTC_CLASS=y +CONFIG_RTC_HCTOSYS=y +CONFIG_RTC_HCTOSYS_DEVICE="rtc0" +# CONFIG_RTC_DEBUG is not set + +# +# RTC interfaces +# +CONFIG_RTC_INTF_SYSFS=y +CONFIG_RTC_INTF_PROC=y +CONFIG_RTC_INTF_DEV=y +# CONFIG_RTC_INTF_DEV_UIE_EMUL is not set +# CONFIG_RTC_DRV_TEST is not set + +# +# I2C RTC drivers +# +# CONFIG_RTC_DRV_DS1307 is not set +# CONFIG_RTC_DRV_DS1374 is not set +# CONFIG_RTC_DRV_DS1672 is not set +# CONFIG_RTC_DRV_MAX6900 is not set +# CONFIG_RTC_DRV_RS5C372 is not set +# CONFIG_RTC_DRV_ISL1208 is not set +# CONFIG_RTC_DRV_X1205 is not set +# CONFIG_RTC_DRV_PCF8563 is not set +# CONFIG_RTC_DRV_PCF8583 is not set +# CONFIG_RTC_DRV_M41T80 is not set + +# +# SPI RTC drivers +# +# CONFIG_RTC_DRV_RS5C348 is not set +# CONFIG_RTC_DRV_MAX6902 is not set +CONFIG_RTC_DRV_M41T94=y + +# +# Platform RTC drivers +# +# CONFIG_RTC_DRV_CMOS is not set +# CONFIG_RTC_DRV_DS1553 is not set +# CONFIG_RTC_DRV_STK17TA8 is not set +# CONFIG_RTC_DRV_DS1742 is not set +# CONFIG_RTC_DRV_M48T86 is not set +# CONFIG_RTC_DRV_M48T59 is not set +# CONFIG_RTC_DRV_V3020 is not set + +# +# on-CPU RTC drivers +# +# CONFIG_RTC_DRV_AT91SAM9 is not set + +# +# File systems +# +CONFIG_EXT2_FS=y +# CONFIG_EXT2_FS_XATTR is not set +# CONFIG_EXT2_FS_XIP is not set +# CONFIG_EXT3_FS is not set +# CONFIG_EXT4DEV_FS is not set +# CONFIG_REISERFS_FS is not set +# CONFIG_JFS_FS is not set +CONFIG_FS_POSIX_ACL=y +# CONFIG_XFS_FS is not set +# CONFIG_GFS2_FS is not set +# CONFIG_OCFS2_FS is not set +# CONFIG_MINIX_FS is not set +# CONFIG_ROMFS_FS is not set +CONFIG_INOTIFY=y +CONFIG_INOTIFY_USER=y +# CONFIG_QUOTA is not set +CONFIG_DNOTIFY=y +# CONFIG_AUTOFS_FS is not set +# CONFIG_AUTOFS4_FS is not set +CONFIG_FUSE_FS=m + +# +# CD-ROM/DVD Filesystems +# +# CONFIG_ISO9660_FS is not set +# CONFIG_UDF_FS is not set + +# +# DOS/FAT/NT Filesystems +# +CONFIG_FAT_FS=y +# CONFIG_MSDOS_FS is not set +CONFIG_VFAT_FS=y +CONFIG_FAT_DEFAULT_CODEPAGE=437 +CONFIG_FAT_DEFAULT_IOCHARSET="iso8859-1" +# CONFIG_NTFS_FS is not set + +# +# Pseudo filesystems +# +CONFIG_PROC_FS=y +CONFIG_PROC_SYSCTL=y +CONFIG_SYSFS=y +CONFIG_TMPFS=y +# CONFIG_TMPFS_POSIX_ACL is not set +# CONFIG_HUGETLB_PAGE is not set +# CONFIG_CONFIGFS_FS is not set + +# +# Miscellaneous filesystems +# +# CONFIG_ADFS_FS is not set +# CONFIG_AFFS_FS is not set +# CONFIG_HFS_FS is not set +# CONFIG_HFSPLUS_FS is not set +# CONFIG_BEFS_FS is not set +# CONFIG_BFS_FS is not set +# CONFIG_EFS_FS is not set +CONFIG_JFFS2_FS=y +CONFIG_JFFS2_FS_DEBUG=0 +CONFIG_JFFS2_FS_WRITEBUFFER=y +# CONFIG_JFFS2_FS_WBUF_VERIFY is not set +# CONFIG_JFFS2_SUMMARY is not set +# CONFIG_JFFS2_FS_XATTR is not set +# CONFIG_JFFS2_COMPRESSION_OPTIONS is not set +CONFIG_JFFS2_ZLIB=y +# CONFIG_JFFS2_LZO is not set +CONFIG_JFFS2_RTIME=y +# CONFIG_JFFS2_RUBIN is not set +# CONFIG_CRAMFS is not set +# CONFIG_VXFS_FS is not set +# CONFIG_HPFS_FS is not set +# CONFIG_QNX4FS_FS is not set +# CONFIG_SYSV_FS is not set +# CONFIG_UFS_FS is not set +CONFIG_NETWORK_FILESYSTEMS=y +CONFIG_NFS_FS=y +CONFIG_NFS_V3=y +CONFIG_NFS_V3_ACL=y +CONFIG_NFS_V4=y +# CONFIG_NFS_DIRECTIO is not set +# CONFIG_NFSD is not set +CONFIG_ROOT_NFS=y +CONFIG_LOCKD=y +CONFIG_LOCKD_V4=y +CONFIG_NFS_ACL_SUPPORT=y +CONFIG_NFS_COMMON=y +CONFIG_SUNRPC=y +CONFIG_SUNRPC_GSS=y +# CONFIG_SUNRPC_BIND34 is not set +CONFIG_RPCSEC_GSS_KRB5=y +# CONFIG_RPCSEC_GSS_SPKM3 is not set +# CONFIG_SMB_FS is not set +# CONFIG_CIFS is not set +# CONFIG_NCP_FS is not set +# CONFIG_CODA_FS is not set +# CONFIG_AFS_FS is not set + +# +# Partition Types +# +# CONFIG_PARTITION_ADVANCED is not set +CONFIG_MSDOS_PARTITION=y +CONFIG_NLS=y +CONFIG_NLS_DEFAULT="iso8859-1" +CONFIG_NLS_CODEPAGE_437=y +# CONFIG_NLS_CODEPAGE_737 is not set +# CONFIG_NLS_CODEPAGE_775 is not set +CONFIG_NLS_CODEPAGE_850=y +# CONFIG_NLS_CODEPAGE_852 is not set +# CONFIG_NLS_CODEPAGE_855 is not set +# CONFIG_NLS_CODEPAGE_857 is not set +# CONFIG_NLS_CODEPAGE_860 is not set +# CONFIG_NLS_CODEPAGE_861 is not set +# CONFIG_NLS_CODEPAGE_862 is not set +# CONFIG_NLS_CODEPAGE_863 is not set +# CONFIG_NLS_CODEPAGE_864 is not set +# CONFIG_NLS_CODEPAGE_865 is not set +# CONFIG_NLS_CODEPAGE_866 is not set +# CONFIG_NLS_CODEPAGE_869 is not set +# CONFIG_NLS_CODEPAGE_936 is not set +# CONFIG_NLS_CODEPAGE_950 is not set +# CONFIG_NLS_CODEPAGE_932 is not set +# CONFIG_NLS_CODEPAGE_949 is not set +# CONFIG_NLS_CODEPAGE_874 is not set +# CONFIG_NLS_ISO8859_8 is not set +# CONFIG_NLS_CODEPAGE_1250 is not set +# CONFIG_NLS_CODEPAGE_1251 is not set +# CONFIG_NLS_ASCII is not set +CONFIG_NLS_ISO8859_1=y +# CONFIG_NLS_ISO8859_2 is not set +# CONFIG_NLS_ISO8859_3 is not set +# CONFIG_NLS_ISO8859_4 is not set +# CONFIG_NLS_ISO8859_5 is not set +# CONFIG_NLS_ISO8859_6 is not set +# CONFIG_NLS_ISO8859_7 is not set +# CONFIG_NLS_ISO8859_9 is not set +# CONFIG_NLS_ISO8859_13 is not set +# CONFIG_NLS_ISO8859_14 is not set +# CONFIG_NLS_ISO8859_15 is not set +# CONFIG_NLS_KOI8_R is not set +# CONFIG_NLS_KOI8_U is not set +# CONFIG_NLS_UTF8 is not set +# CONFIG_DLM is not set +# CONFIG_INSTRUMENTATION is not set + +# +# Kernel hacking +# +# CONFIG_PRINTK_TIME is not set +CONFIG_ENABLE_WARN_DEPRECATED=y +CONFIG_ENABLE_MUST_CHECK=y +# CONFIG_MAGIC_SYSRQ is not set +# CONFIG_UNUSED_SYMBOLS is not set +# CONFIG_DEBUG_FS is not set +# CONFIG_HEADERS_CHECK is not set +CONFIG_DEBUG_KERNEL=y +# CONFIG_DEBUG_SHIRQ is not set +CONFIG_DETECT_SOFTLOCKUP=y +CONFIG_SCHED_DEBUG=y +# CONFIG_SCHEDSTATS is not set +# CONFIG_TIMER_STATS is not set +# CONFIG_DEBUG_SLAB is not set +# CONFIG_DEBUG_RT_MUTEXES is not set +# CONFIG_RT_MUTEX_TESTER is not set +# CONFIG_DEBUG_SPINLOCK is not set +# CONFIG_DEBUG_MUTEXES is not set +# CONFIG_DEBUG_LOCK_ALLOC is not set +# CONFIG_PROVE_LOCKING is not set +# CONFIG_LOCK_STAT is not set +# CONFIG_DEBUG_SPINLOCK_SLEEP is not set +# CONFIG_DEBUG_LOCKING_API_SELFTESTS is not set +# CONFIG_DEBUG_KOBJECT is not set +CONFIG_DEBUG_BUGVERBOSE=y +# CONFIG_DEBUG_INFO is not set +# CONFIG_DEBUG_VM is not set +# CONFIG_DEBUG_LIST is not set +# CONFIG_DEBUG_SG is not set +CONFIG_FRAME_POINTER=y +CONFIG_FORCED_INLINING=y +# CONFIG_BOOT_PRINTK_DELAY is not set +# CONFIG_RCU_TORTURE_TEST is not set +# CONFIG_FAULT_INJECTION is not set +# CONFIG_SAMPLES is not set +CONFIG_DEBUG_USER=y +# CONFIG_DEBUG_ERRORS is not set +CONFIG_DEBUG_LL=y +# CONFIG_DEBUG_ICEDCC is not set + +# +# Security options +# +# CONFIG_KEYS is not set +# CONFIG_SECURITY is not set +# CONFIG_SECURITY_FILE_CAPABILITIES is not set +CONFIG_CRYPTO=y +CONFIG_CRYPTO_ALGAPI=y +CONFIG_CRYPTO_BLKCIPHER=y +CONFIG_CRYPTO_MANAGER=y +# CONFIG_CRYPTO_HMAC is not set +# CONFIG_CRYPTO_XCBC is not set +# CONFIG_CRYPTO_NULL is not set +# CONFIG_CRYPTO_MD4 is not set +CONFIG_CRYPTO_MD5=y +# CONFIG_CRYPTO_SHA1 is not set +# CONFIG_CRYPTO_SHA256 is not set +# CONFIG_CRYPTO_SHA512 is not set +# CONFIG_CRYPTO_WP512 is not set +# CONFIG_CRYPTO_TGR192 is not set +# CONFIG_CRYPTO_GF128MUL is not set +# CONFIG_CRYPTO_ECB is not set +CONFIG_CRYPTO_CBC=y +# CONFIG_CRYPTO_PCBC is not set +# CONFIG_CRYPTO_LRW is not set +# CONFIG_CRYPTO_XTS is not set +# CONFIG_CRYPTO_CRYPTD is not set +CONFIG_CRYPTO_DES=y +# CONFIG_CRYPTO_FCRYPT is not set +# CONFIG_CRYPTO_BLOWFISH is not set +# CONFIG_CRYPTO_TWOFISH is not set +# CONFIG_CRYPTO_SERPENT is not set +# CONFIG_CRYPTO_AES is not set +# CONFIG_CRYPTO_CAST5 is not set +# CONFIG_CRYPTO_CAST6 is not set +# CONFIG_CRYPTO_TEA is not set +# CONFIG_CRYPTO_ARC4 is not set +# CONFIG_CRYPTO_KHAZAD is not set +# CONFIG_CRYPTO_ANUBIS is not set +# CONFIG_CRYPTO_SEED is not set +# CONFIG_CRYPTO_DEFLATE is not set +# CONFIG_CRYPTO_MICHAEL_MIC is not set +# CONFIG_CRYPTO_CRC32C is not set +# CONFIG_CRYPTO_CAMELLIA is not set +# CONFIG_CRYPTO_TEST is not set +# CONFIG_CRYPTO_AUTHENC is not set +# CONFIG_CRYPTO_HW is not set + +# +# Library routines +# +CONFIG_BITREVERSE=y +# CONFIG_CRC_CCITT is not set +# CONFIG_CRC16 is not set +# CONFIG_CRC_ITU_T is not set +CONFIG_CRC32=y +# CONFIG_CRC7 is not set +# CONFIG_LIBCRC32C is not set +CONFIG_ZLIB_INFLATE=y +CONFIG_ZLIB_DEFLATE=y +CONFIG_PLIST=y +CONFIG_HAS_IOMEM=y +CONFIG_HAS_IOPORT=y +CONFIG_HAS_DMA=y diff --git a/arch/arm/configs/realview-smp_defconfig b/arch/arm/configs/realview-smp_defconfig index fc39ba1a89f..0c09b23167e 100644 --- a/arch/arm/configs/realview-smp_defconfig +++ b/arch/arm/configs/realview-smp_defconfig @@ -177,7 +177,6 @@ CONFIG_NR_CPUS=4 CONFIG_HOTPLUG_CPU=y CONFIG_LOCAL_TIMERS=y # CONFIG_PREEMPT is not set -# CONFIG_NO_IDLE_HZ is not set CONFIG_HZ=100 # CONFIG_AEABI is not set # CONFIG_ARCH_DISCONTIGMEM_ENABLE is not set diff --git a/arch/arm/configs/realview_defconfig b/arch/arm/configs/realview_defconfig index accbf529ce5..907e54344da 100644 --- a/arch/arm/configs/realview_defconfig +++ b/arch/arm/configs/realview_defconfig @@ -126,7 +126,6 @@ CONFIG_ISA_DMA_API=y # # Kernel Features # -# CONFIG_NO_IDLE_HZ is not set # CONFIG_ARCH_DISCONTIGMEM_ENABLE is not set CONFIG_FLATMEM=y CONFIG_FLAT_NODE_MEM_MAP=y diff --git a/arch/arm/configs/rpc_defconfig b/arch/arm/configs/rpc_defconfig index 5ddecb9ddf0..f62d1817d2c 100644 --- a/arch/arm/configs/rpc_defconfig +++ b/arch/arm/configs/rpc_defconfig @@ -190,7 +190,6 @@ CONFIG_ISA_DMA_API=y # # CONFIG_TICK_ONESHOT is not set # CONFIG_PREEMPT is not set -# CONFIG_NO_IDLE_HZ is not set CONFIG_HZ=100 # CONFIG_AEABI is not set # CONFIG_ARCH_DISCONTIGMEM_ENABLE is not set diff --git a/arch/arm/configs/s3c2410_defconfig b/arch/arm/configs/s3c2410_defconfig index f8a1645b3d4..35faaea8623 100644 --- a/arch/arm/configs/s3c2410_defconfig +++ b/arch/arm/configs/s3c2410_defconfig @@ -1,15 +1,18 @@ # # Automatically generated make config: don't edit -# Linux kernel version: 2.6.21-rc6 -# Mon Apr 9 10:12:58 2007 +# Linux kernel version: 2.6.26-rc8 +# Mon Jul 7 16:59:23 2008 # CONFIG_ARM=y CONFIG_SYS_SUPPORTS_APM_EMULATION=y CONFIG_GENERIC_GPIO=y # CONFIG_GENERIC_TIME is not set +# CONFIG_GENERIC_CLOCKEVENTS is not set CONFIG_MMU=y CONFIG_NO_IOPORT=y CONFIG_GENERIC_HARDIRQS=y +CONFIG_STACKTRACE_SUPPORT=y +CONFIG_LOCKDEP_SUPPORT=y CONFIG_TRACE_IRQFLAGS_SUPPORT=y CONFIG_HARDIRQS_SW_RESEND=y CONFIG_GENERIC_IRQ_PROBE=y @@ -18,34 +21,39 @@ CONFIG_RWSEM_GENERIC_SPINLOCK=y # CONFIG_ARCH_HAS_ILOG2_U64 is not set CONFIG_GENERIC_HWEIGHT=y CONFIG_GENERIC_CALIBRATE_DELAY=y +CONFIG_ARCH_SUPPORTS_AOUT=y CONFIG_ZONE_DMA=y CONFIG_VECTORS_BASE=0xffff0000 CONFIG_DEFCONFIG_LIST="/lib/modules/$UNAME_RELEASE/.config" # -# Code maturity level options +# General setup # CONFIG_EXPERIMENTAL=y CONFIG_BROKEN_ON_SMP=y CONFIG_INIT_ENV_ARG_LIMIT=32 - -# -# General setup -# CONFIG_LOCALVERSION="" CONFIG_LOCALVERSION_AUTO=y CONFIG_SWAP=y CONFIG_SYSVIPC=y -# CONFIG_IPC_NS is not set CONFIG_SYSVIPC_SYSCTL=y # CONFIG_POSIX_MQUEUE is not set # CONFIG_BSD_PROCESS_ACCT is not set # CONFIG_TASKSTATS is not set -# CONFIG_UTS_NS is not set # CONFIG_AUDIT is not set -# CONFIG_IKCONFIG is not set +CONFIG_IKCONFIG=m +CONFIG_IKCONFIG_PROC=y +CONFIG_LOG_BUF_SHIFT=16 +# CONFIG_CGROUPS is not set +# CONFIG_GROUP_SCHED is not set CONFIG_SYSFS_DEPRECATED=y +CONFIG_SYSFS_DEPRECATED_V2=y # CONFIG_RELAY is not set +CONFIG_NAMESPACES=y +# CONFIG_UTS_NS is not set +# CONFIG_IPC_NS is not set +# CONFIG_USER_NS is not set +# CONFIG_PID_NS is not set CONFIG_BLK_DEV_INITRD=y CONFIG_INITRAMFS_SOURCE="" CONFIG_CC_OPTIMIZE_FOR_SIZE=y @@ -53,6 +61,7 @@ CONFIG_SYSCTL=y # CONFIG_EMBEDDED is not set CONFIG_UID16=y CONFIG_SYSCTL_SYSCALL=y +CONFIG_SYSCTL_SYSCALL_CHECK=y CONFIG_KALLSYMS=y # CONFIG_KALLSYMS_ALL is not set # CONFIG_KALLSYMS_EXTRA_PASS is not set @@ -60,34 +69,43 @@ CONFIG_HOTPLUG=y CONFIG_PRINTK=y CONFIG_BUG=y CONFIG_ELF_CORE=y +CONFIG_COMPAT_BRK=y CONFIG_BASE_FULL=y CONFIG_FUTEX=y +CONFIG_ANON_INODES=y CONFIG_EPOLL=y +CONFIG_SIGNALFD=y +CONFIG_TIMERFD=y +CONFIG_EVENTFD=y CONFIG_SHMEM=y -CONFIG_SLAB=y CONFIG_VM_EVENT_COUNTERS=y +CONFIG_SLAB=y +# CONFIG_SLUB is not set +# CONFIG_SLOB is not set +# CONFIG_PROFILING is not set +# CONFIG_MARKERS is not set +CONFIG_HAVE_OPROFILE=y +# CONFIG_KPROBES is not set +CONFIG_HAVE_KPROBES=y +CONFIG_HAVE_KRETPROBES=y +# CONFIG_HAVE_DMA_ATTRS is not set +CONFIG_PROC_PAGE_MONITOR=y +CONFIG_SLABINFO=y CONFIG_RT_MUTEXES=y # CONFIG_TINY_SHMEM is not set CONFIG_BASE_SMALL=0 -# CONFIG_SLOB is not set - -# -# Loadable module support -# CONFIG_MODULES=y +# CONFIG_MODULE_FORCE_LOAD is not set CONFIG_MODULE_UNLOAD=y # CONFIG_MODULE_FORCE_UNLOAD is not set # CONFIG_MODVERSIONS is not set # CONFIG_MODULE_SRCVERSION_ALL is not set CONFIG_KMOD=y - -# -# Block layer -# CONFIG_BLOCK=y # CONFIG_LBD is not set # CONFIG_BLK_DEV_IO_TRACE is not set # CONFIG_LSF is not set +# CONFIG_BLK_DEV_BSG is not set # # IO Schedulers @@ -101,6 +119,7 @@ CONFIG_DEFAULT_AS=y # CONFIG_DEFAULT_CFQ is not set # CONFIG_DEFAULT_NOOP is not set CONFIG_DEFAULT_IOSCHED="anticipatory" +CONFIG_CLASSIC_RCU=y # # System Type @@ -119,14 +138,17 @@ CONFIG_DEFAULT_IOSCHED="anticipatory" # CONFIG_ARCH_NETX is not set # CONFIG_ARCH_H720X is not set # CONFIG_ARCH_IMX is not set +# CONFIG_ARCH_IOP13XX is not set # CONFIG_ARCH_IOP32X is not set # CONFIG_ARCH_IOP33X is not set -# CONFIG_ARCH_IOP13XX is not set -# CONFIG_ARCH_IXP4XX is not set -# CONFIG_ARCH_IXP2000 is not set # CONFIG_ARCH_IXP23XX is not set +# CONFIG_ARCH_IXP2000 is not set +# CONFIG_ARCH_IXP4XX is not set # CONFIG_ARCH_L7200 is not set +# CONFIG_ARCH_KS8695 is not set # CONFIG_ARCH_NS9XXX is not set +# CONFIG_ARCH_MXC is not set +# CONFIG_ARCH_ORION5X is not set # CONFIG_ARCH_PNX4008 is not set # CONFIG_ARCH_PXA is not set # CONFIG_ARCH_RPC is not set @@ -134,18 +156,32 @@ CONFIG_DEFAULT_IOSCHED="anticipatory" CONFIG_ARCH_S3C2410=y # CONFIG_ARCH_SHARK is not set # CONFIG_ARCH_LH7A40X is not set +# CONFIG_ARCH_DAVINCI is not set # CONFIG_ARCH_OMAP is not set +# CONFIG_ARCH_MSM7X00A is not set CONFIG_PLAT_S3C24XX=y CONFIG_CPU_S3C244X=y +# CONFIG_S3C24XX_PWM is not set CONFIG_PM_SIMTEC=y +CONFIG_S3C2410_DMA=y +# CONFIG_S3C2410_DMA_DEBUG is not set +CONFIG_MACH_SMDK=y +CONFIG_PLAT_S3C=y +CONFIG_CPU_LLSERIAL_S3C2410=y +CONFIG_CPU_LLSERIAL_S3C2440=y + +# +# Boot options +# # CONFIG_S3C_BOOT_WATCHDOG is not set # CONFIG_S3C_BOOT_ERROR_RESET is not set + +# +# Power management +# # CONFIG_S3C2410_PM_DEBUG is not set # CONFIG_S3C2410_PM_CHECK is not set CONFIG_S3C_LOWLEVEL_UART_PORT=0 -CONFIG_S3C2410_DMA=y -# CONFIG_S3C2410_DMA_DEBUG is not set -CONFIG_MACH_SMDK=y # # S3C2400 Machines @@ -155,6 +191,8 @@ CONFIG_CPU_S3C2410_DMA=y CONFIG_S3C2410_PM=y CONFIG_S3C2410_GPIO=y CONFIG_S3C2410_CLOCK=y +CONFIG_SIMTEC_NOR=y +CONFIG_MACH_BAST_IDE=y # # S3C2410 Machines @@ -167,6 +205,7 @@ CONFIG_ARCH_BAST=y CONFIG_MACH_OTOM=y CONFIG_MACH_AML_M5900=y CONFIG_BAST_PC104_IRQ=y +# CONFIG_MACH_TCT_HAMMER is not set CONFIG_MACH_VR1000=y CONFIG_MACH_QT2410=y CONFIG_CPU_S3C2412=y @@ -176,8 +215,10 @@ CONFIG_S3C2412_PM=y # # S3C2412 Machines # +# CONFIG_MACH_JIVE is not set CONFIG_MACH_SMDK2413=y CONFIG_MACH_S3C2413=y +# CONFIG_MACH_SMDK2412 is not set CONFIG_MACH_VSTMS=y CONFIG_CPU_S3C2440=y CONFIG_S3C2440_DMA=y @@ -191,6 +232,7 @@ CONFIG_MACH_RX3715=y CONFIG_ARCH_S3C2440=y CONFIG_MACH_NEXCODER_2440=y CONFIG_SMDK2440_CPU2440=y +# CONFIG_MACH_AT2440EVB is not set CONFIG_CPU_S3C2442=y # @@ -215,6 +257,7 @@ CONFIG_CPU_32v4T=y CONFIG_CPU_32v5=y CONFIG_CPU_ABRT_EV4T=y CONFIG_CPU_ABRT_EV5TJ=y +CONFIG_CPU_PABRT_NOIFAR=y CONFIG_CPU_CACHE_V4WT=y CONFIG_CPU_CACHE_VIVT=y CONFIG_CPU_COPY_V4WB=y @@ -236,17 +279,15 @@ CONFIG_CPU_CP15_MMU=y # Bus support # CONFIG_ISA=y - -# -# PCCARD (PCMCIA/CardBus) support -# +# CONFIG_PCI_SYSCALL is not set +# CONFIG_ARCH_SUPPORTS_MSI is not set # CONFIG_PCCARD is not set # # Kernel Features # +# CONFIG_TICK_ONESHOT is not set # CONFIG_PREEMPT is not set -# CONFIG_NO_IDLE_HZ is not set CONFIG_HZ=200 # CONFIG_AEABI is not set # CONFIG_ARCH_DISCONTIGMEM_ENABLE is not set @@ -257,9 +298,13 @@ CONFIG_FLATMEM_MANUAL=y CONFIG_FLATMEM=y CONFIG_FLAT_NODE_MEM_MAP=y # CONFIG_SPARSEMEM_STATIC is not set +# CONFIG_SPARSEMEM_VMEMMAP_ENABLE is not set +CONFIG_PAGEFLAGS_EXTENDED=y CONFIG_SPLIT_PTLOCK_CPUS=4096 # CONFIG_RESOURCES_64BIT is not set CONFIG_ZONE_DMA_FLAG=1 +CONFIG_BOUNCE=y +CONFIG_VIRT_TO_BUS=y CONFIG_ALIGNMENT_TRAP=y # @@ -279,7 +324,7 @@ CONFIG_CMDLINE="root=/dev/hda1 ro init=/bin/bash console=ttySAC0" # At least one emulation must be selected # CONFIG_FPE_NWFPE=y -# CONFIG_FPE_NWFPE_XP is not set +CONFIG_FPE_NWFPE_XP=y # CONFIG_FPE_FASTFPE is not set # CONFIG_VFP is not set @@ -295,10 +340,12 @@ CONFIG_BINFMT_AOUT=y # Power management options # CONFIG_PM=y -# CONFIG_PM_LEGACY is not set # CONFIG_PM_DEBUG is not set -# CONFIG_PM_SYSFS_DEPRECATED is not set -# CONFIG_APM_EMULATION is not set +CONFIG_PM_SLEEP=y +CONFIG_SUSPEND=y +CONFIG_SUSPEND_FREEZER=y +CONFIG_APM_EMULATION=m +CONFIG_ARCH_SUSPEND_POSSIBLE=y # # Networking @@ -308,59 +355,67 @@ CONFIG_NET=y # # Networking options # -# CONFIG_NETDEBUG is not set -# CONFIG_PACKET is not set +CONFIG_PACKET=y +# CONFIG_PACKET_MMAP is not set CONFIG_UNIX=y CONFIG_XFRM=y # CONFIG_XFRM_USER is not set # CONFIG_XFRM_SUB_POLICY is not set # CONFIG_XFRM_MIGRATE is not set +# CONFIG_XFRM_STATISTICS is not set # CONFIG_NET_KEY is not set CONFIG_INET=y -# CONFIG_IP_MULTICAST is not set +CONFIG_IP_MULTICAST=y # CONFIG_IP_ADVANCED_ROUTER is not set CONFIG_IP_FIB_HASH=y CONFIG_IP_PNP=y -# CONFIG_IP_PNP_DHCP is not set +CONFIG_IP_PNP_DHCP=y CONFIG_IP_PNP_BOOTP=y # CONFIG_IP_PNP_RARP is not set # CONFIG_NET_IPIP is not set # CONFIG_NET_IPGRE is not set +# CONFIG_IP_MROUTE is not set # CONFIG_ARPD is not set # CONFIG_SYN_COOKIES is not set # CONFIG_INET_AH is not set # CONFIG_INET_ESP is not set # CONFIG_INET_IPCOMP is not set # CONFIG_INET_XFRM_TUNNEL is not set -# CONFIG_INET_TUNNEL is not set +CONFIG_INET_TUNNEL=m CONFIG_INET_XFRM_MODE_TRANSPORT=y CONFIG_INET_XFRM_MODE_TUNNEL=y CONFIG_INET_XFRM_MODE_BEET=y +# CONFIG_INET_LRO is not set CONFIG_INET_DIAG=y CONFIG_INET_TCP_DIAG=y # CONFIG_TCP_CONG_ADVANCED is not set CONFIG_TCP_CONG_CUBIC=y CONFIG_DEFAULT_TCP_CONG="cubic" # CONFIG_TCP_MD5SIG is not set -# CONFIG_IPV6 is not set -# CONFIG_INET6_XFRM_TUNNEL is not set -# CONFIG_INET6_TUNNEL is not set +CONFIG_IPV6=m +CONFIG_IPV6_PRIVACY=y +CONFIG_IPV6_ROUTER_PREF=y +# CONFIG_IPV6_ROUTE_INFO is not set +# CONFIG_IPV6_OPTIMISTIC_DAD is not set +CONFIG_INET6_AH=m +CONFIG_INET6_ESP=m +CONFIG_INET6_IPCOMP=m +CONFIG_IPV6_MIP6=m +CONFIG_INET6_XFRM_TUNNEL=m +CONFIG_INET6_TUNNEL=m +CONFIG_INET6_XFRM_MODE_TRANSPORT=m +CONFIG_INET6_XFRM_MODE_TUNNEL=m +CONFIG_INET6_XFRM_MODE_BEET=m +CONFIG_INET6_XFRM_MODE_ROUTEOPTIMIZATION=m +CONFIG_IPV6_SIT=m +CONFIG_IPV6_NDISC_NODETYPE=y +CONFIG_IPV6_TUNNEL=m +# CONFIG_IPV6_MULTIPLE_TABLES is not set +# CONFIG_IPV6_MROUTE is not set # CONFIG_NETWORK_SECMARK is not set # CONFIG_NETFILTER is not set - -# -# DCCP Configuration (EXPERIMENTAL) -# # CONFIG_IP_DCCP is not set - -# -# SCTP Configuration (EXPERIMENTAL) -# # CONFIG_IP_SCTP is not set - -# -# TIPC Configuration (EXPERIMENTAL) -# # CONFIG_TIPC is not set # CONFIG_ATM is not set # CONFIG_BRIDGE is not set @@ -373,20 +428,71 @@ CONFIG_DEFAULT_TCP_CONG="cubic" # CONFIG_LAPB is not set # CONFIG_ECONET is not set # CONFIG_WAN_ROUTER is not set - -# -# QoS and/or fair queueing -# # CONFIG_NET_SCHED is not set +CONFIG_NET_SCH_FIFO=y # # Network testing # # CONFIG_NET_PKTGEN is not set # CONFIG_HAMRADIO is not set +# CONFIG_CAN is not set # CONFIG_IRDA is not set -# CONFIG_BT is not set +CONFIG_BT=m +CONFIG_BT_L2CAP=m +CONFIG_BT_SCO=m +CONFIG_BT_RFCOMM=m +CONFIG_BT_RFCOMM_TTY=y +CONFIG_BT_BNEP=m +CONFIG_BT_BNEP_MC_FILTER=y +CONFIG_BT_BNEP_PROTO_FILTER=y +CONFIG_BT_HIDP=m + +# +# Bluetooth device drivers +# +CONFIG_BT_HCIUSB=m +CONFIG_BT_HCIUSB_SCO=y +CONFIG_BT_HCIUART=m +CONFIG_BT_HCIUART_H4=y +CONFIG_BT_HCIUART_BCSP=y +CONFIG_BT_HCIUART_LL=y +CONFIG_BT_HCIBCM203X=m +CONFIG_BT_HCIBPA10X=m +CONFIG_BT_HCIBFUSB=m +CONFIG_BT_HCIVHCI=m +# CONFIG_AF_RXRPC is not set + +# +# Wireless +# +CONFIG_CFG80211=m +CONFIG_NL80211=y +CONFIG_WIRELESS_EXT=y +CONFIG_MAC80211=m + +# +# Rate control algorithm selection +# +CONFIG_MAC80211_RC_DEFAULT_PID=y +# CONFIG_MAC80211_RC_DEFAULT_NONE is not set + +# +# Selecting 'y' for an algorithm will +# + +# +# build the algorithm into mac80211. +# +CONFIG_MAC80211_RC_DEFAULT="pid" +CONFIG_MAC80211_RC_PID=y +CONFIG_MAC80211_MESH=y +CONFIG_MAC80211_LEDS=y +# CONFIG_MAC80211_DEBUG_PACKET_ALIGNMENT is not set +# CONFIG_MAC80211_DEBUG is not set # CONFIG_IEEE80211 is not set +# CONFIG_RFKILL is not set +# CONFIG_NET_9P is not set # # Device Drivers @@ -395,21 +501,14 @@ CONFIG_DEFAULT_TCP_CONG="cubic" # # Generic Driver Options # +CONFIG_UEVENT_HELPER_PATH="/sbin/hotplug" CONFIG_STANDALONE=y CONFIG_PREVENT_FIRMWARE_BUILD=y -# CONFIG_FW_LOADER is not set +CONFIG_FW_LOADER=m # CONFIG_DEBUG_DRIVER is not set # CONFIG_DEBUG_DEVRES is not set # CONFIG_SYS_HYPERVISOR is not set - -# -# Connector - unified userspace <-> kernelspace linker -# # CONFIG_CONNECTOR is not set - -# -# Memory Technology Devices (MTD) -# CONFIG_MTD=y # CONFIG_MTD_DEBUG is not set # CONFIG_MTD_CONCAT is not set @@ -420,6 +519,7 @@ CONFIG_MTD_REDBOOT_PARTS_UNALLOCATED=y # CONFIG_MTD_REDBOOT_PARTS_READONLY is not set CONFIG_MTD_CMDLINE_PARTS=y # CONFIG_MTD_AFS_PARTS is not set +# CONFIG_MTD_AR7_PARTS is not set # # User Modules And Translation Layers @@ -432,6 +532,7 @@ CONFIG_MTD_BLOCK=y # CONFIG_INFTL is not set # CONFIG_RFD_FTL is not set # CONFIG_SSFDC is not set +# CONFIG_MTD_OOPS is not set # # RAM/ROM/Flash chip drivers @@ -457,7 +558,6 @@ CONFIG_MTD_CFI_UTIL=y # CONFIG_MTD_RAM is not set CONFIG_MTD_ROM=y # CONFIG_MTD_ABSENT is not set -# CONFIG_MTD_OBSOLETE_CHIPS is not set # # Mapping drivers for chip access @@ -486,13 +586,10 @@ CONFIG_MTD_BAST_MAXSIZE=4 # CONFIG_MTD_DOC2000 is not set # CONFIG_MTD_DOC2001 is not set # CONFIG_MTD_DOC2001PLUS is not set - -# -# NAND Flash Device Drivers -# CONFIG_MTD_NAND=y # CONFIG_MTD_NAND_VERIFY_WRITE is not set # CONFIG_MTD_NAND_ECC_SMC is not set +# CONFIG_MTD_NAND_MUSEUM_IDS is not set CONFIG_MTD_NAND_IDS=y CONFIG_MTD_NAND_S3C2410=y # CONFIG_MTD_NAND_S3C2410_DEBUG is not set @@ -500,30 +597,25 @@ CONFIG_MTD_NAND_S3C2410=y # CONFIG_MTD_NAND_S3C2410_CLKSTOP is not set # CONFIG_MTD_NAND_DISKONCHIP is not set # CONFIG_MTD_NAND_NANDSIM is not set - -# -# OneNAND Flash Device Drivers -# +# CONFIG_MTD_NAND_PLATFORM is not set +# CONFIG_MTD_ALAUDA is not set # CONFIG_MTD_ONENAND is not set # -# Parallel port support +# UBI - Unsorted block images # +# CONFIG_MTD_UBI is not set CONFIG_PARPORT=y -# CONFIG_PARPORT_PC is not set +CONFIG_PARPORT_PC=m +# CONFIG_PARPORT_PC_FIFO is not set +# CONFIG_PARPORT_PC_SUPERIO is not set # CONFIG_PARPORT_GSC is not set -# CONFIG_PARPORT_AX88796 is not set +CONFIG_PARPORT_AX88796=m CONFIG_PARPORT_1284=y - -# -# Plug and Play support -# +CONFIG_PARPORT_NOT_PC=y # CONFIG_PNP is not set -# CONFIG_PNPACPI is not set - -# -# Block devices -# +CONFIG_BLK_DEV=y +# CONFIG_PARIDE is not set # CONFIG_BLK_DEV_COW_COMMON is not set CONFIG_BLK_DEV_LOOP=y # CONFIG_BLK_DEV_CRYPTOLOOP is not set @@ -532,34 +624,34 @@ CONFIG_BLK_DEV_NBD=m CONFIG_BLK_DEV_RAM=y CONFIG_BLK_DEV_RAM_COUNT=16 CONFIG_BLK_DEV_RAM_SIZE=4096 -CONFIG_BLK_DEV_RAM_BLOCKSIZE=1024 +# CONFIG_BLK_DEV_XIP is not set # CONFIG_CDROM_PKTCDVD is not set CONFIG_ATA_OVER_ETH=m - -# -# ATA/ATAPI/MFM/RLL support -# +CONFIG_MISC_DEVICES=y +# CONFIG_EEPROM_93CX6 is not set +# CONFIG_ENCLOSURE_SERVICES is not set +CONFIG_HAVE_IDE=y CONFIG_IDE=y CONFIG_BLK_DEV_IDE=y # -# Please see Documentation/ide.txt for help/info on IDE drives +# Please see Documentation/ide/ide.txt for help/info on IDE drives # # CONFIG_BLK_DEV_IDE_SATA is not set CONFIG_BLK_DEV_IDEDISK=y # CONFIG_IDEDISK_MULTI_MODE is not set CONFIG_BLK_DEV_IDECD=y +CONFIG_BLK_DEV_IDECD_VERBOSE_ERRORS=y CONFIG_BLK_DEV_IDETAPE=m CONFIG_BLK_DEV_IDEFLOPPY=m +# CONFIG_BLK_DEV_IDESCSI is not set # CONFIG_IDE_TASK_IOCTL is not set +CONFIG_IDE_PROC_FS=y # # IDE chipset support/bugfixes # -CONFIG_IDE_GENERIC=y -# CONFIG_IDE_ARM is not set -CONFIG_BLK_DEV_IDE_BAST=y -# CONFIG_IDE_CHIPSETS is not set +# CONFIG_BLK_DEV_PLATFORM is not set # CONFIG_BLK_DEV_IDEDMA is not set # CONFIG_BLK_DEV_HD is not set @@ -567,101 +659,119 @@ CONFIG_BLK_DEV_IDE_BAST=y # SCSI device support # # CONFIG_RAID_ATTRS is not set -# CONFIG_SCSI is not set +CONFIG_SCSI=y +CONFIG_SCSI_DMA=y +CONFIG_SCSI_TGT=m # CONFIG_SCSI_NETLINK is not set - -# -# Serial ATA (prod) and Parallel ATA (experimental) drivers -# +CONFIG_SCSI_PROC_FS=y + +# +# SCSI support type (disk, tape, CD-ROM) +# +CONFIG_BLK_DEV_SD=y +CONFIG_CHR_DEV_ST=m +# CONFIG_CHR_DEV_OSST is not set +CONFIG_BLK_DEV_SR=m +CONFIG_BLK_DEV_SR_VENDOR=y +CONFIG_CHR_DEV_SG=y +CONFIG_CHR_DEV_SCH=m + +# +# Some SCSI devices (e.g. CD jukebox) support multiple LUNs +# +CONFIG_SCSI_MULTI_LUN=y +CONFIG_SCSI_CONSTANTS=y +# CONFIG_SCSI_LOGGING is not set +CONFIG_SCSI_SCAN_ASYNC=y +CONFIG_SCSI_WAIT_SCAN=m + +# +# SCSI Transports +# +# CONFIG_SCSI_SPI_ATTRS is not set +# CONFIG_SCSI_FC_ATTRS is not set +# CONFIG_SCSI_ISCSI_ATTRS is not set +# CONFIG_SCSI_SAS_LIBSAS is not set +# CONFIG_SCSI_SRP_ATTRS is not set +CONFIG_SCSI_LOWLEVEL=y +# CONFIG_ISCSI_TCP is not set +# CONFIG_SCSI_AHA152X is not set +# CONFIG_SCSI_AIC7XXX_OLD is not set +# CONFIG_SCSI_ADVANSYS is not set +# CONFIG_SCSI_IN2000 is not set +# CONFIG_SCSI_DTC3280 is not set +# CONFIG_SCSI_FUTURE_DOMAIN is not set +# CONFIG_SCSI_GENERIC_NCR5380 is not set +# CONFIG_SCSI_GENERIC_NCR5380_MMIO is not set +# CONFIG_SCSI_PPA is not set +# CONFIG_SCSI_IMM is not set +# CONFIG_SCSI_NCR53C406A is not set +# CONFIG_SCSI_PAS16 is not set +# CONFIG_SCSI_QLOGIC_FAS is not set +# CONFIG_SCSI_SYM53C416 is not set +# CONFIG_SCSI_T128 is not set +# CONFIG_SCSI_DEBUG is not set # CONFIG_ATA is not set - -# -# Multi-device support (RAID and LVM) -# +CONFIG_HAVE_PATA_PLATFORM=y # CONFIG_MD is not set - -# -# Fusion MPT device support -# -# CONFIG_FUSION is not set - -# -# IEEE 1394 (FireWire) support -# - -# -# I2O device support -# - -# -# Network device support -# CONFIG_NETDEVICES=y +# CONFIG_NETDEVICES_MULTIQUEUE is not set # CONFIG_DUMMY is not set # CONFIG_BONDING is not set +# CONFIG_MACVLAN is not set # CONFIG_EQUALIZER is not set # CONFIG_TUN is not set - -# -# ARCnet devices -# +# CONFIG_VETH is not set # CONFIG_ARCNET is not set - -# -# PHY device support -# # CONFIG_PHYLIB is not set - -# -# Ethernet (10 or 100Mbit) -# CONFIG_NET_ETHERNET=y CONFIG_MII=y +# CONFIG_AX88796 is not set # CONFIG_NET_VENDOR_3COM is not set # CONFIG_NET_VENDOR_SMC is not set # CONFIG_SMC91X is not set CONFIG_DM9000=y +# CONFIG_ENC28J60 is not set +CONFIG_DM9000_DEBUGLEVEL=4 # CONFIG_NET_VENDOR_RACAL is not set # CONFIG_AT1700 is not set # CONFIG_DEPCA is not set # CONFIG_HP100 is not set # CONFIG_NET_ISA is not set +# CONFIG_IBM_NEW_EMAC_ZMII is not set +# CONFIG_IBM_NEW_EMAC_RGMII is not set +# CONFIG_IBM_NEW_EMAC_TAH is not set +# CONFIG_IBM_NEW_EMAC_EMAC4 is not set # CONFIG_NET_PCI is not set +# CONFIG_B44 is not set # CONFIG_NET_POCKET is not set - -# -# Ethernet (1000 Mbit) -# - -# -# Ethernet (10000 Mbit) -# - -# -# Token Ring devices -# +CONFIG_NETDEV_1000=y +# CONFIG_E1000E_ENABLED is not set +CONFIG_NETDEV_10000=y # CONFIG_TR is not set # -# Wireless LAN (non-hamradio) +# Wireless LAN # -# CONFIG_NET_RADIO is not set +# CONFIG_WLAN_PRE80211 is not set +# CONFIG_WLAN_80211 is not set +# CONFIG_IWLWIFI_LEDS is not set # -# Wan interfaces +# USB Network Adapters # +# CONFIG_USB_CATC is not set +# CONFIG_USB_KAWETH is not set +# CONFIG_USB_PEGASUS is not set +# CONFIG_USB_RTL8150 is not set +# CONFIG_USB_USBNET is not set # CONFIG_WAN is not set # CONFIG_PLIP is not set # CONFIG_PPP is not set # CONFIG_SLIP is not set -# CONFIG_SHAPER is not set # CONFIG_NETCONSOLE is not set # CONFIG_NETPOLL is not set # CONFIG_NET_POLL_CONTROLLER is not set - -# -# ISDN subsystem -# # CONFIG_ISDN is not set # @@ -669,6 +779,7 @@ CONFIG_DM9000=y # CONFIG_INPUT=y # CONFIG_INPUT_FF_MEMLESS is not set +# CONFIG_INPUT_POLLDEV is not set # # Userland interfaces @@ -678,7 +789,6 @@ CONFIG_INPUT_MOUSEDEV_PSAUX=y CONFIG_INPUT_MOUSEDEV_SCREEN_X=1024 CONFIG_INPUT_MOUSEDEV_SCREEN_Y=768 # CONFIG_INPUT_JOYDEV is not set -# CONFIG_INPUT_TSDEV is not set # CONFIG_INPUT_EVDEV is not set # CONFIG_INPUT_EVBUG is not set @@ -695,12 +805,21 @@ CONFIG_KEYBOARD_ATKBD=y # CONFIG_KEYBOARD_GPIO is not set CONFIG_INPUT_MOUSE=y CONFIG_MOUSE_PS2=y +CONFIG_MOUSE_PS2_ALPS=y +CONFIG_MOUSE_PS2_LOGIPS2PP=y +CONFIG_MOUSE_PS2_SYNAPTICS=y +CONFIG_MOUSE_PS2_LIFEBOOK=y +CONFIG_MOUSE_PS2_TRACKPOINT=y +# CONFIG_MOUSE_PS2_TOUCHKIT is not set # CONFIG_MOUSE_SERIAL is not set +# CONFIG_MOUSE_APPLETOUCH is not set # CONFIG_MOUSE_INPORT is not set # CONFIG_MOUSE_LOGIBM is not set # CONFIG_MOUSE_PC110PAD is not set # CONFIG_MOUSE_VSXXXAA is not set +# CONFIG_MOUSE_GPIO is not set # CONFIG_INPUT_JOYSTICK is not set +# CONFIG_INPUT_TABLET is not set # CONFIG_INPUT_TOUCHSCREEN is not set # CONFIG_INPUT_MISC is not set @@ -721,6 +840,7 @@ CONFIG_VT=y CONFIG_VT_CONSOLE=y CONFIG_HW_CONSOLE=y # CONFIG_VT_HW_CONSOLE_BINDING is not set +CONFIG_DEVKMEM=y CONFIG_SERIAL_NONSTANDARD=y # CONFIG_COMPUTONE is not set # CONFIG_ROCKETPORT is not set @@ -728,8 +848,6 @@ CONFIG_SERIAL_NONSTANDARD=y # CONFIG_DIGIEPCA is not set # CONFIG_MOXA_INTELLIO is not set # CONFIG_MOXA_SMARTIO is not set -# CONFIG_MOXA_SMARTIO_NEW is not set -# CONFIG_SYNCLINKMP is not set # CONFIG_N_HDLC is not set # CONFIG_RISCOM8 is not set # CONFIG_SPECIALIX is not set @@ -758,8 +876,12 @@ CONFIG_SERIAL_8250_SHARE_IRQ=y # # Non-8250 serial port support # +CONFIG_SERIAL_SAMSUNG=y +# CONFIG_SERIAL_SAMSUNG_DEBUG is not set +CONFIG_SERIAL_SAMSUNG_CONSOLE=y CONFIG_SERIAL_S3C2410=y -CONFIG_SERIAL_S3C2410_CONSOLE=y +CONFIG_SERIAL_S3C2412=y +CONFIG_SERIAL_S3C2440=y CONFIG_SERIAL_CORE=y CONFIG_SERIAL_CORE_CONSOLE=y CONFIG_UNIX98_PTYS=y @@ -768,89 +890,50 @@ CONFIG_LEGACY_PTY_COUNT=256 CONFIG_PRINTER=y # CONFIG_LP_CONSOLE is not set CONFIG_PPDEV=y -# CONFIG_TIPAR is not set - -# -# IPMI -# # CONFIG_IPMI_HANDLER is not set - -# -# Watchdog Cards -# -CONFIG_WATCHDOG=y -# CONFIG_WATCHDOG_NOWAYOUT is not set - -# -# Watchdog Device Drivers -# -# CONFIG_SOFT_WATCHDOG is not set -CONFIG_S3C2410_WATCHDOG=y - -# -# ISA-based Watchdog Cards -# -# CONFIG_PCWATCHDOG is not set -# CONFIG_MIXCOMWD is not set -# CONFIG_WDT is not set - -# -# USB-based Watchdog Cards -# -# CONFIG_USBPCWATCHDOG is not set CONFIG_HW_RANDOM=y # CONFIG_NVRAM is not set # CONFIG_DTLK is not set # CONFIG_R3964 is not set # CONFIG_RAW_DRIVER is not set - -# -# TPM devices -# # CONFIG_TCG_TPM is not set - -# -# I2C support -# +CONFIG_DEVPORT=y CONFIG_I2C=y +CONFIG_I2C_BOARDINFO=y CONFIG_I2C_CHARDEV=m - -# -# I2C Algorithms -# -CONFIG_I2C_ALGOBIT=m -# CONFIG_I2C_ALGOPCF is not set -# CONFIG_I2C_ALGOPCA is not set +CONFIG_I2C_ALGOBIT=y # # I2C Hardware Bus support # # CONFIG_I2C_ELEKTOR is not set +# CONFIG_I2C_GPIO is not set # CONFIG_I2C_OCORES is not set # CONFIG_I2C_PARPORT is not set # CONFIG_I2C_PARPORT_LIGHT is not set CONFIG_I2C_S3C2410=y +CONFIG_I2C_SIMTEC=y +# CONFIG_I2C_TAOS_EVM is not set # CONFIG_I2C_STUB is not set +# CONFIG_I2C_TINY_USB is not set # CONFIG_I2C_PCA_ISA is not set +# CONFIG_I2C_PCA_PLATFORM is not set # # Miscellaneous I2C Chip support # -# CONFIG_SENSORS_DS1337 is not set -# CONFIG_SENSORS_DS1374 is not set +# CONFIG_DS1682 is not set CONFIG_SENSORS_EEPROM=m # CONFIG_SENSORS_PCF8574 is not set -# CONFIG_SENSORS_PCA9539 is not set +# CONFIG_PCF8575 is not set # CONFIG_SENSORS_PCF8591 is not set +# CONFIG_TPS65010 is not set # CONFIG_SENSORS_MAX6875 is not set +# CONFIG_SENSORS_TSL2550 is not set # CONFIG_I2C_DEBUG_CORE is not set # CONFIG_I2C_DEBUG_ALGO is not set # CONFIG_I2C_DEBUG_BUS is not set # CONFIG_I2C_DEBUG_CHIP is not set - -# -# SPI support -# CONFIG_SPI=y # CONFIG_SPI_DEBUG is not set CONFIG_SPI_MASTER=y @@ -860,6 +943,7 @@ CONFIG_SPI_MASTER=y # CONFIG_SPI_BITBANG=m # CONFIG_SPI_BUTTERFLY is not set +# CONFIG_SPI_LM70_LLP is not set CONFIG_SPI_S3C24XX=m CONFIG_SPI_S3C24XX_GPIO=m @@ -867,30 +951,43 @@ CONFIG_SPI_S3C24XX_GPIO=m # SPI Protocol Masters # # CONFIG_SPI_AT25 is not set +# CONFIG_SPI_SPIDEV is not set +# CONFIG_SPI_TLE62X0 is not set +CONFIG_HAVE_GPIO_LIB=y # -# Dallas's 1-wire bus +# GPIO Support # -# CONFIG_W1 is not set +# CONFIG_DEBUG_GPIO is not set # -# Hardware Monitoring support +# I2C GPIO expanders: +# +# CONFIG_GPIO_PCA953X is not set +# CONFIG_GPIO_PCF857X is not set + # +# SPI GPIO expanders: +# +# CONFIG_GPIO_MCP23S08 is not set +# CONFIG_W1 is not set +# CONFIG_POWER_SUPPLY is not set CONFIG_HWMON=y CONFIG_HWMON_VID=m -# CONFIG_SENSORS_ABITUGURU is not set +# CONFIG_SENSORS_AD7418 is not set # CONFIG_SENSORS_ADM1021 is not set # CONFIG_SENSORS_ADM1025 is not set # CONFIG_SENSORS_ADM1026 is not set # CONFIG_SENSORS_ADM1029 is not set # CONFIG_SENSORS_ADM1031 is not set # CONFIG_SENSORS_ADM9240 is not set -# CONFIG_SENSORS_ASB100 is not set +# CONFIG_SENSORS_ADT7470 is not set +# CONFIG_SENSORS_ADT7473 is not set # CONFIG_SENSORS_ATXP1 is not set # CONFIG_SENSORS_DS1621 is not set # CONFIG_SENSORS_F71805F is not set -# CONFIG_SENSORS_FSCHER is not set -# CONFIG_SENSORS_FSCPOS is not set +# CONFIG_SENSORS_F71882FG is not set +# CONFIG_SENSORS_F75375S is not set # CONFIG_SENSORS_GL518SM is not set # CONFIG_SENSORS_GL520SM is not set # CONFIG_SENSORS_IT87 is not set @@ -905,72 +1002,95 @@ CONFIG_SENSORS_LM85=m # CONFIG_SENSORS_LM87 is not set # CONFIG_SENSORS_LM90 is not set # CONFIG_SENSORS_LM92 is not set +# CONFIG_SENSORS_LM93 is not set # CONFIG_SENSORS_MAX1619 is not set +# CONFIG_SENSORS_MAX6650 is not set # CONFIG_SENSORS_PC87360 is not set # CONFIG_SENSORS_PC87427 is not set +# CONFIG_SENSORS_DME1737 is not set # CONFIG_SENSORS_SMSC47M1 is not set # CONFIG_SENSORS_SMSC47M192 is not set # CONFIG_SENSORS_SMSC47B397 is not set +# CONFIG_SENSORS_ADS7828 is not set +# CONFIG_SENSORS_THMC50 is not set # CONFIG_SENSORS_VT1211 is not set # CONFIG_SENSORS_W83781D is not set # CONFIG_SENSORS_W83791D is not set # CONFIG_SENSORS_W83792D is not set # CONFIG_SENSORS_W83793 is not set # CONFIG_SENSORS_W83L785TS is not set +# CONFIG_SENSORS_W83L786NG is not set # CONFIG_SENSORS_W83627HF is not set # CONFIG_SENSORS_W83627EHF is not set # CONFIG_HWMON_DEBUG_CHIP is not set +CONFIG_WATCHDOG=y +# CONFIG_WATCHDOG_NOWAYOUT is not set # -# Misc devices +# Watchdog Device Drivers # +# CONFIG_SOFT_WATCHDOG is not set +CONFIG_S3C2410_WATCHDOG=y # -# Multifunction device drivers +# ISA-based Watchdog Cards # -# CONFIG_MFD_SM501 is not set +# CONFIG_PCWATCHDOG is not set +# CONFIG_MIXCOMWD is not set +# CONFIG_WDT is not set # -# LED devices +# USB-based Watchdog Cards # -CONFIG_NEW_LEDS=y -CONFIG_LEDS_CLASS=m +# CONFIG_USBPCWATCHDOG is not set # -# LED drivers +# Sonics Silicon Backplane # -CONFIG_LEDS_S3C24XX=m -CONFIG_LEDS_H1940=m +CONFIG_SSB_POSSIBLE=y +# CONFIG_SSB is not set # -# LED Triggers +# Multifunction device drivers # -CONFIG_LEDS_TRIGGERS=y -CONFIG_LEDS_TRIGGER_TIMER=m -# CONFIG_LEDS_TRIGGER_IDE_DISK is not set -CONFIG_LEDS_TRIGGER_HEARTBEAT=m +CONFIG_MFD_SM501=y +# CONFIG_MFD_ASIC3 is not set +# CONFIG_HTC_EGPIO is not set +# CONFIG_HTC_PASIC3 is not set # # Multimedia devices # + +# +# Multimedia core support +# # CONFIG_VIDEO_DEV is not set +# CONFIG_DVB_CORE is not set +# CONFIG_VIDEO_MEDIA is not set # -# Digital Video Broadcasting Devices +# Multimedia drivers # -# CONFIG_DVB is not set -# CONFIG_USB_DABUSB is not set +# CONFIG_DAB is not set # # Graphics support # -# CONFIG_BACKLIGHT_LCD_SUPPORT is not set +# CONFIG_VGASTATE is not set +# CONFIG_VIDEO_OUTPUT_CONTROL is not set CONFIG_FB=y CONFIG_FIRMWARE_EDID=y # CONFIG_FB_DDC is not set CONFIG_FB_CFB_FILLRECT=y CONFIG_FB_CFB_COPYAREA=y CONFIG_FB_CFB_IMAGEBLIT=y +# CONFIG_FB_CFB_REV_PIXELS_IN_BYTE is not set +# CONFIG_FB_SYS_FILLRECT is not set +# CONFIG_FB_SYS_COPYAREA is not set +# CONFIG_FB_SYS_IMAGEBLIT is not set +# CONFIG_FB_FOREIGN_ENDIAN is not set +# CONFIG_FB_SYS_FOPS is not set # CONFIG_FB_SVGALIB is not set # CONFIG_FB_MACMODES is not set # CONFIG_FB_BACKLIGHT is not set @@ -978,12 +1098,19 @@ CONFIG_FB_MODE_HELPERS=y # CONFIG_FB_TILEBLITTING is not set # -# Frambuffer hardware drivers +# Frame buffer hardware drivers # # CONFIG_FB_S1D13XXX is not set CONFIG_FB_S3C2410=y # CONFIG_FB_S3C2410_DEBUG is not set +CONFIG_FB_SM501=y # CONFIG_FB_VIRTUAL is not set +# CONFIG_BACKLIGHT_LCD_SUPPORT is not set + +# +# Display device support +# +# CONFIG_DISPLAY_SUPPORT is not set # # Console display driver support @@ -992,40 +1119,45 @@ CONFIG_FB_S3C2410=y # CONFIG_MDA_CONSOLE is not set CONFIG_DUMMY_CONSOLE=y CONFIG_FRAMEBUFFER_CONSOLE=y +# CONFIG_FRAMEBUFFER_CONSOLE_DETECT_PRIMARY is not set # CONFIG_FRAMEBUFFER_CONSOLE_ROTATION is not set # CONFIG_FONTS is not set CONFIG_FONT_8x8=y CONFIG_FONT_8x16=y - -# -# Logo configuration -# # CONFIG_LOGO is not set # # Sound # # CONFIG_SOUND is not set +CONFIG_HID_SUPPORT=y +CONFIG_HID=y +# CONFIG_HID_DEBUG is not set +# CONFIG_HIDRAW is not set # -# HID Devices +# USB Input Devices # -CONFIG_HID=y -# CONFIG_HID_DEBUG is not set +# CONFIG_USB_HID is not set # -# USB support +# USB HID Boot Protocol drivers # +# CONFIG_USB_KBD is not set +# CONFIG_USB_MOUSE is not set +CONFIG_USB_SUPPORT=y CONFIG_USB_ARCH_HAS_HCD=y CONFIG_USB_ARCH_HAS_OHCI=y # CONFIG_USB_ARCH_HAS_EHCI is not set CONFIG_USB=y # CONFIG_USB_DEBUG is not set +# CONFIG_USB_ANNOUNCE_NEW_DEVICES is not set # # Miscellaneous USB options # CONFIG_USB_DEVICEFS=y +CONFIG_USB_DEVICE_CLASS=y # CONFIG_USB_DYNAMIC_MINORS is not set # CONFIG_USB_SUSPEND is not set # CONFIG_USB_OTG is not set @@ -1033,18 +1165,22 @@ CONFIG_USB_DEVICEFS=y # # USB Host Controller Drivers # +# CONFIG_USB_C67X00_HCD is not set # CONFIG_USB_ISP116X_HCD is not set +# CONFIG_USB_ISP1760_HCD is not set CONFIG_USB_OHCI_HCD=y # CONFIG_USB_OHCI_BIG_ENDIAN_DESC is not set # CONFIG_USB_OHCI_BIG_ENDIAN_MMIO is not set CONFIG_USB_OHCI_LITTLE_ENDIAN=y # CONFIG_USB_SL811_HCD is not set +# CONFIG_USB_R8A66597_HCD is not set # # USB Device Class drivers # -# CONFIG_USB_ACM is not set -# CONFIG_USB_PRINTER is not set +CONFIG_USB_ACM=m +CONFIG_USB_PRINTER=m +CONFIG_USB_WDM=m # # NOTE: USB_STORAGE enables SCSI, and 'SCSI disk support' @@ -1053,57 +1189,78 @@ CONFIG_USB_OHCI_LITTLE_ENDIAN=y # # may also be needed; see USB_STORAGE Help for more information # -# CONFIG_USB_LIBUSUAL is not set - -# -# USB Input Devices -# -# CONFIG_USB_HID is not set - -# -# USB HID Boot Protocol drivers -# -# CONFIG_USB_KBD is not set -# CONFIG_USB_MOUSE is not set -# CONFIG_USB_AIPTEK is not set -# CONFIG_USB_WACOM is not set -# CONFIG_USB_ACECAD is not set -# CONFIG_USB_KBTAB is not set -# CONFIG_USB_POWERMATE is not set -# CONFIG_USB_TOUCHSCREEN is not set -# CONFIG_USB_YEALINK is not set -# CONFIG_USB_XPAD is not set -# CONFIG_USB_ATI_REMOTE is not set -# CONFIG_USB_ATI_REMOTE2 is not set -# CONFIG_USB_KEYSPAN_REMOTE is not set -# CONFIG_USB_APPLETOUCH is not set -# CONFIG_USB_GTCO is not set +CONFIG_USB_STORAGE=m +# CONFIG_USB_STORAGE_DEBUG is not set +# CONFIG_USB_STORAGE_DATAFAB is not set +# CONFIG_USB_STORAGE_FREECOM is not set +# CONFIG_USB_STORAGE_ISD200 is not set +# CONFIG_USB_STORAGE_DPCM is not set +# CONFIG_USB_STORAGE_USBAT is not set +# CONFIG_USB_STORAGE_SDDR09 is not set +# CONFIG_USB_STORAGE_SDDR55 is not set +# CONFIG_USB_STORAGE_JUMPSHOT is not set +# CONFIG_USB_STORAGE_ALAUDA is not set +# CONFIG_USB_STORAGE_ONETOUCH is not set +# CONFIG_USB_STORAGE_KARMA is not set +# CONFIG_USB_STORAGE_CYPRESS_ATACB is not set +CONFIG_USB_LIBUSUAL=y # # USB Imaging devices # # CONFIG_USB_MDC800 is not set - -# -# USB Network Adapters -# -# CONFIG_USB_CATC is not set -# CONFIG_USB_KAWETH is not set -# CONFIG_USB_PEGASUS is not set -# CONFIG_USB_RTL8150 is not set -# CONFIG_USB_USBNET_MII is not set -# CONFIG_USB_USBNET is not set +# CONFIG_USB_MICROTEK is not set CONFIG_USB_MON=y # # USB port drivers # # CONFIG_USB_USS720 is not set - -# -# USB Serial Converter support -# -# CONFIG_USB_SERIAL is not set +CONFIG_USB_SERIAL=y +# CONFIG_USB_SERIAL_CONSOLE is not set +# CONFIG_USB_EZUSB is not set +CONFIG_USB_SERIAL_GENERIC=y +# CONFIG_USB_SERIAL_AIRCABLE is not set +# CONFIG_USB_SERIAL_AIRPRIME is not set +# CONFIG_USB_SERIAL_ARK3116 is not set +# CONFIG_USB_SERIAL_BELKIN is not set +# CONFIG_USB_SERIAL_CH341 is not set +# CONFIG_USB_SERIAL_WHITEHEAT is not set +# CONFIG_USB_SERIAL_DIGI_ACCELEPORT is not set +# CONFIG_USB_SERIAL_CP2101 is not set +# CONFIG_USB_SERIAL_CYPRESS_M8 is not set +# CONFIG_USB_SERIAL_EMPEG is not set +CONFIG_USB_SERIAL_FTDI_SIO=y +# CONFIG_USB_SERIAL_FUNSOFT is not set +# CONFIG_USB_SERIAL_VISOR is not set +# CONFIG_USB_SERIAL_IPAQ is not set +# CONFIG_USB_SERIAL_IR is not set +# CONFIG_USB_SERIAL_EDGEPORT is not set +# CONFIG_USB_SERIAL_EDGEPORT_TI is not set +# CONFIG_USB_SERIAL_GARMIN is not set +# CONFIG_USB_SERIAL_IPW is not set +# CONFIG_USB_SERIAL_IUU is not set +# CONFIG_USB_SERIAL_KEYSPAN_PDA is not set +# CONFIG_USB_SERIAL_KEYSPAN is not set +# CONFIG_USB_SERIAL_KLSI is not set +# CONFIG_USB_SERIAL_KOBIL_SCT is not set +# CONFIG_USB_SERIAL_MCT_U232 is not set +# CONFIG_USB_SERIAL_MOS7720 is not set +# CONFIG_USB_SERIAL_MOS7840 is not set +# CONFIG_USB_SERIAL_MOTOROLA is not set +CONFIG_USB_SERIAL_NAVMAN=m +CONFIG_USB_SERIAL_PL2303=y +# CONFIG_USB_SERIAL_OTI6858 is not set +# CONFIG_USB_SERIAL_SPCP8X5 is not set +# CONFIG_USB_SERIAL_HP4X is not set +# CONFIG_USB_SERIAL_SAFE is not set +# CONFIG_USB_SERIAL_SIERRAWIRELESS is not set +# CONFIG_USB_SERIAL_TI is not set +# CONFIG_USB_SERIAL_CYBERJACK is not set +# CONFIG_USB_SERIAL_XIRCOM is not set +CONFIG_USB_SERIAL_OPTION=m +# CONFIG_USB_SERIAL_OMNINET is not set +# CONFIG_USB_SERIAL_DEBUG is not set # # USB Miscellaneous drivers @@ -1116,35 +1273,38 @@ CONFIG_USB_MON=y # CONFIG_USB_LEGOTOWER is not set # CONFIG_USB_LCD is not set # CONFIG_USB_BERRY_CHARGE is not set -# CONFIG_USB_LED is not set +CONFIG_USB_LED=m # CONFIG_USB_CYPRESS_CY7C63 is not set # CONFIG_USB_CYTHERM is not set # CONFIG_USB_PHIDGET is not set # CONFIG_USB_IDMOUSE is not set # CONFIG_USB_FTDI_ELAN is not set # CONFIG_USB_APPLEDISPLAY is not set -# CONFIG_USB_LD is not set +CONFIG_USB_LD=m # CONFIG_USB_TRANCEVIBRATOR is not set # CONFIG_USB_IOWARRIOR is not set # CONFIG_USB_TEST is not set - -# -# USB DSL modem support -# - -# -# USB Gadget Support -# +# CONFIG_USB_ISIGHTFW is not set # CONFIG_USB_GADGET is not set +# CONFIG_MMC is not set +CONFIG_NEW_LEDS=y +CONFIG_LEDS_CLASS=m # -# MMC/SD Card support +# LED drivers # -# CONFIG_MMC is not set +CONFIG_LEDS_S3C24XX=m +CONFIG_LEDS_H1940=m +# CONFIG_LEDS_GPIO is not set # -# Real Time Clock +# LED Triggers # +CONFIG_LEDS_TRIGGERS=y +CONFIG_LEDS_TRIGGER_TIMER=m +# CONFIG_LEDS_TRIGGER_IDE_DISK is not set +CONFIG_LEDS_TRIGGER_HEARTBEAT=m +# CONFIG_LEDS_TRIGGER_DEFAULT_ON is not set CONFIG_RTC_LIB=y CONFIG_RTC_CLASS=y CONFIG_RTC_HCTOSYS=y @@ -1158,61 +1318,86 @@ CONFIG_RTC_INTF_SYSFS=y CONFIG_RTC_INTF_PROC=y CONFIG_RTC_INTF_DEV=y # CONFIG_RTC_INTF_DEV_UIE_EMUL is not set +# CONFIG_RTC_DRV_TEST is not set # -# RTC drivers +# I2C RTC drivers # -# CONFIG_RTC_DRV_CMOS is not set -# CONFIG_RTC_DRV_X1205 is not set # CONFIG_RTC_DRV_DS1307 is not set -# CONFIG_RTC_DRV_DS1553 is not set -# CONFIG_RTC_DRV_ISL1208 is not set +# CONFIG_RTC_DRV_DS1374 is not set # CONFIG_RTC_DRV_DS1672 is not set -# CONFIG_RTC_DRV_DS1742 is not set +# CONFIG_RTC_DRV_MAX6900 is not set +# CONFIG_RTC_DRV_RS5C372 is not set +# CONFIG_RTC_DRV_ISL1208 is not set +# CONFIG_RTC_DRV_X1205 is not set # CONFIG_RTC_DRV_PCF8563 is not set +# CONFIG_RTC_DRV_PCF8583 is not set +# CONFIG_RTC_DRV_M41T80 is not set +# CONFIG_RTC_DRV_S35390A is not set +# CONFIG_RTC_DRV_FM3130 is not set + +# +# SPI RTC drivers +# +# CONFIG_RTC_DRV_MAX6902 is not set +# CONFIG_RTC_DRV_R9701 is not set # CONFIG_RTC_DRV_RS5C348 is not set -# CONFIG_RTC_DRV_RS5C372 is not set -CONFIG_RTC_DRV_S3C=y + +# +# Platform RTC drivers +# +# CONFIG_RTC_DRV_CMOS is not set +# CONFIG_RTC_DRV_DS1511 is not set +# CONFIG_RTC_DRV_DS1553 is not set +# CONFIG_RTC_DRV_DS1742 is not set +# CONFIG_RTC_DRV_STK17TA8 is not set # CONFIG_RTC_DRV_M48T86 is not set -# CONFIG_RTC_DRV_TEST is not set -# CONFIG_RTC_DRV_MAX6902 is not set +# CONFIG_RTC_DRV_M48T59 is not set # CONFIG_RTC_DRV_V3020 is not set # +# on-CPU RTC drivers +# +CONFIG_RTC_DRV_S3C=y +# CONFIG_UIO is not set + +# # File systems # CONFIG_EXT2_FS=y -# CONFIG_EXT2_FS_XATTR is not set +CONFIG_EXT2_FS_XATTR=y +CONFIG_EXT2_FS_POSIX_ACL=y +CONFIG_EXT2_FS_SECURITY=y # CONFIG_EXT2_FS_XIP is not set CONFIG_EXT3_FS=y CONFIG_EXT3_FS_XATTR=y -# CONFIG_EXT3_FS_POSIX_ACL is not set +CONFIG_EXT3_FS_POSIX_ACL=y # CONFIG_EXT3_FS_SECURITY is not set # CONFIG_EXT4DEV_FS is not set CONFIG_JBD=y -# CONFIG_JBD_DEBUG is not set CONFIG_FS_MBCACHE=y # CONFIG_REISERFS_FS is not set # CONFIG_JFS_FS is not set -# CONFIG_FS_POSIX_ACL is not set +CONFIG_FS_POSIX_ACL=y # CONFIG_XFS_FS is not set -# CONFIG_GFS2_FS is not set # CONFIG_OCFS2_FS is not set -# CONFIG_MINIX_FS is not set -CONFIG_ROMFS_FS=y +CONFIG_DNOTIFY=y CONFIG_INOTIFY=y CONFIG_INOTIFY_USER=y # CONFIG_QUOTA is not set -CONFIG_DNOTIFY=y # CONFIG_AUTOFS_FS is not set # CONFIG_AUTOFS4_FS is not set # CONFIG_FUSE_FS is not set +CONFIG_GENERIC_ACL=y # # CD-ROM/DVD Filesystems # -# CONFIG_ISO9660_FS is not set -# CONFIG_UDF_FS is not set +CONFIG_ISO9660_FS=y +CONFIG_JOLIET=y +# CONFIG_ZISOFS is not set +CONFIG_UDF_FS=m +CONFIG_UDF_NLS=y # # DOS/FAT/NT Filesystems @@ -1222,7 +1407,9 @@ CONFIG_MSDOS_FS=y CONFIG_VFAT_FS=y CONFIG_FAT_DEFAULT_CODEPAGE=437 CONFIG_FAT_DEFAULT_IOCHARSET="iso8859-1" -# CONFIG_NTFS_FS is not set +CONFIG_NTFS_FS=m +# CONFIG_NTFS_DEBUG is not set +# CONFIG_NTFS_RW is not set # # Pseudo filesystems @@ -1230,10 +1417,10 @@ CONFIG_FAT_DEFAULT_IOCHARSET="iso8859-1" CONFIG_PROC_FS=y CONFIG_PROC_SYSCTL=y CONFIG_SYSFS=y -# CONFIG_TMPFS is not set +CONFIG_TMPFS=y +CONFIG_TMPFS_POSIX_ACL=y # CONFIG_HUGETLB_PAGE is not set -CONFIG_RAMFS=y -# CONFIG_CONFIGFS_FS is not set +CONFIG_CONFIGFS_FS=m # # Miscellaneous filesystems @@ -1248,31 +1435,32 @@ CONFIG_RAMFS=y CONFIG_JFFS2_FS=y CONFIG_JFFS2_FS_DEBUG=0 CONFIG_JFFS2_FS_WRITEBUFFER=y -# CONFIG_JFFS2_SUMMARY is not set +# CONFIG_JFFS2_FS_WBUF_VERIFY is not set +CONFIG_JFFS2_SUMMARY=y # CONFIG_JFFS2_FS_XATTR is not set # CONFIG_JFFS2_COMPRESSION_OPTIONS is not set CONFIG_JFFS2_ZLIB=y +# CONFIG_JFFS2_LZO is not set CONFIG_JFFS2_RTIME=y # CONFIG_JFFS2_RUBIN is not set CONFIG_CRAMFS=y # CONFIG_VXFS_FS is not set +# CONFIG_MINIX_FS is not set # CONFIG_HPFS_FS is not set # CONFIG_QNX4FS_FS is not set +CONFIG_ROMFS_FS=y # CONFIG_SYSV_FS is not set # CONFIG_UFS_FS is not set - -# -# Network File Systems -# +CONFIG_NETWORK_FILESYSTEMS=y CONFIG_NFS_FS=y # CONFIG_NFS_V3 is not set # CONFIG_NFS_V4 is not set -# CONFIG_NFS_DIRECTIO is not set # CONFIG_NFSD is not set CONFIG_ROOT_NFS=y CONFIG_LOCKD=y CONFIG_NFS_COMMON=y CONFIG_SUNRPC=y +# CONFIG_SUNRPC_BIND34 is not set # CONFIG_RPCSEC_GSS_KRB5 is not set # CONFIG_RPCSEC_GSS_SPKM3 is not set # CONFIG_SMB_FS is not set @@ -1280,7 +1468,6 @@ CONFIG_SUNRPC=y # CONFIG_NCP_FS is not set # CONFIG_CODA_FS is not set # CONFIG_AFS_FS is not set -# CONFIG_9P_FS is not set # # Partition Types @@ -1302,94 +1489,93 @@ CONFIG_SOLARIS_X86_PARTITION=y # CONFIG_SUN_PARTITION is not set # CONFIG_KARMA_PARTITION is not set # CONFIG_EFI_PARTITION is not set - -# -# Native Language Support -# +# CONFIG_SYSV68_PARTITION is not set CONFIG_NLS=y CONFIG_NLS_DEFAULT="iso8859-1" -# CONFIG_NLS_CODEPAGE_437 is not set -# CONFIG_NLS_CODEPAGE_737 is not set -# CONFIG_NLS_CODEPAGE_775 is not set -# CONFIG_NLS_CODEPAGE_850 is not set -# CONFIG_NLS_CODEPAGE_852 is not set -# CONFIG_NLS_CODEPAGE_855 is not set -# CONFIG_NLS_CODEPAGE_857 is not set -# CONFIG_NLS_CODEPAGE_860 is not set -# CONFIG_NLS_CODEPAGE_861 is not set -# CONFIG_NLS_CODEPAGE_862 is not set -# CONFIG_NLS_CODEPAGE_863 is not set -# CONFIG_NLS_CODEPAGE_864 is not set -# CONFIG_NLS_CODEPAGE_865 is not set -# CONFIG_NLS_CODEPAGE_866 is not set -# CONFIG_NLS_CODEPAGE_869 is not set -# CONFIG_NLS_CODEPAGE_936 is not set -# CONFIG_NLS_CODEPAGE_950 is not set -# CONFIG_NLS_CODEPAGE_932 is not set -# CONFIG_NLS_CODEPAGE_949 is not set -# CONFIG_NLS_CODEPAGE_874 is not set -# CONFIG_NLS_ISO8859_8 is not set -# CONFIG_NLS_CODEPAGE_1250 is not set -# CONFIG_NLS_CODEPAGE_1251 is not set -# CONFIG_NLS_ASCII is not set -# CONFIG_NLS_ISO8859_1 is not set -# CONFIG_NLS_ISO8859_2 is not set -# CONFIG_NLS_ISO8859_3 is not set -# CONFIG_NLS_ISO8859_4 is not set -# CONFIG_NLS_ISO8859_5 is not set -# CONFIG_NLS_ISO8859_6 is not set -# CONFIG_NLS_ISO8859_7 is not set -# CONFIG_NLS_ISO8859_9 is not set -# CONFIG_NLS_ISO8859_13 is not set -# CONFIG_NLS_ISO8859_14 is not set -# CONFIG_NLS_ISO8859_15 is not set -# CONFIG_NLS_KOI8_R is not set -# CONFIG_NLS_KOI8_U is not set -# CONFIG_NLS_UTF8 is not set - -# -# Distributed Lock Manager -# +CONFIG_NLS_CODEPAGE_437=y +CONFIG_NLS_CODEPAGE_737=m +CONFIG_NLS_CODEPAGE_775=m +CONFIG_NLS_CODEPAGE_850=y +CONFIG_NLS_CODEPAGE_852=m +CONFIG_NLS_CODEPAGE_855=m +CONFIG_NLS_CODEPAGE_857=m +CONFIG_NLS_CODEPAGE_860=m +CONFIG_NLS_CODEPAGE_861=m +CONFIG_NLS_CODEPAGE_862=m +CONFIG_NLS_CODEPAGE_863=m +CONFIG_NLS_CODEPAGE_864=m +CONFIG_NLS_CODEPAGE_865=m +CONFIG_NLS_CODEPAGE_866=m +CONFIG_NLS_CODEPAGE_869=m +CONFIG_NLS_CODEPAGE_936=m +CONFIG_NLS_CODEPAGE_950=m +CONFIG_NLS_CODEPAGE_932=m +CONFIG_NLS_CODEPAGE_949=m +CONFIG_NLS_CODEPAGE_874=m +CONFIG_NLS_ISO8859_8=m +CONFIG_NLS_CODEPAGE_1250=m +CONFIG_NLS_CODEPAGE_1251=m +CONFIG_NLS_ASCII=y +CONFIG_NLS_ISO8859_1=y +CONFIG_NLS_ISO8859_2=m +CONFIG_NLS_ISO8859_3=m +CONFIG_NLS_ISO8859_4=m +CONFIG_NLS_ISO8859_5=m +CONFIG_NLS_ISO8859_6=m +CONFIG_NLS_ISO8859_7=m +CONFIG_NLS_ISO8859_9=m +CONFIG_NLS_ISO8859_13=m +CONFIG_NLS_ISO8859_14=m +CONFIG_NLS_ISO8859_15=m +CONFIG_NLS_KOI8_R=m +CONFIG_NLS_KOI8_U=m +CONFIG_NLS_UTF8=m # CONFIG_DLM is not set # -# Profiling support -# -# CONFIG_PROFILING is not set - -# # Kernel hacking # # CONFIG_PRINTK_TIME is not set +CONFIG_ENABLE_WARN_DEPRECATED=y CONFIG_ENABLE_MUST_CHECK=y +CONFIG_FRAME_WARN=1024 CONFIG_MAGIC_SYSRQ=y # CONFIG_UNUSED_SYMBOLS is not set # CONFIG_DEBUG_FS is not set # CONFIG_HEADERS_CHECK is not set CONFIG_DEBUG_KERNEL=y # CONFIG_DEBUG_SHIRQ is not set -CONFIG_LOG_BUF_SHIFT=16 CONFIG_DETECT_SOFTLOCKUP=y +CONFIG_SCHED_DEBUG=y # CONFIG_SCHEDSTATS is not set # CONFIG_TIMER_STATS is not set +# CONFIG_DEBUG_OBJECTS is not set # CONFIG_DEBUG_SLAB is not set # CONFIG_DEBUG_RT_MUTEXES is not set # CONFIG_RT_MUTEX_TESTER is not set # CONFIG_DEBUG_SPINLOCK is not set CONFIG_DEBUG_MUTEXES=y +# CONFIG_DEBUG_LOCK_ALLOC is not set +# CONFIG_PROVE_LOCKING is not set +# CONFIG_LOCK_STAT is not set # CONFIG_DEBUG_SPINLOCK_SLEEP is not set # CONFIG_DEBUG_LOCKING_API_SELFTESTS is not set # CONFIG_DEBUG_KOBJECT is not set CONFIG_DEBUG_BUGVERBOSE=y CONFIG_DEBUG_INFO=y # CONFIG_DEBUG_VM is not set +# CONFIG_DEBUG_WRITECOUNT is not set # CONFIG_DEBUG_LIST is not set +# CONFIG_DEBUG_SG is not set CONFIG_FRAME_POINTER=y -CONFIG_FORCED_INLINING=y +# CONFIG_BOOT_PRINTK_DELAY is not set # CONFIG_RCU_TORTURE_TEST is not set +# CONFIG_BACKTRACE_SELF_TEST is not set # CONFIG_FAULT_INJECTION is not set +# CONFIG_SAMPLES is not set CONFIG_DEBUG_USER=y -# CONFIG_DEBUG_ERRORS is not set +CONFIG_DEBUG_ERRORS=y +# CONFIG_DEBUG_STACK_USAGE is not set CONFIG_DEBUG_LL=y # CONFIG_DEBUG_ICEDCC is not set CONFIG_DEBUG_S3C_PORT=y @@ -1400,21 +1586,100 @@ CONFIG_DEBUG_S3C_UART=0 # # CONFIG_KEYS is not set # CONFIG_SECURITY is not set +# CONFIG_SECURITY_FILE_CAPABILITIES is not set +CONFIG_CRYPTO=y + +# +# Crypto core or helper +# +CONFIG_CRYPTO_ALGAPI=m +CONFIG_CRYPTO_AEAD=m +CONFIG_CRYPTO_BLKCIPHER=m +CONFIG_CRYPTO_HASH=m +CONFIG_CRYPTO_MANAGER=m +# CONFIG_CRYPTO_GF128MUL is not set +# CONFIG_CRYPTO_NULL is not set +# CONFIG_CRYPTO_CRYPTD is not set +CONFIG_CRYPTO_AUTHENC=m +# CONFIG_CRYPTO_TEST is not set + +# +# Authenticated Encryption with Associated Data +# +# CONFIG_CRYPTO_CCM is not set +# CONFIG_CRYPTO_GCM is not set +# CONFIG_CRYPTO_SEQIV is not set + +# +# Block modes +# +CONFIG_CRYPTO_CBC=m +# CONFIG_CRYPTO_CTR is not set +# CONFIG_CRYPTO_CTS is not set +CONFIG_CRYPTO_ECB=m +# CONFIG_CRYPTO_LRW is not set +# CONFIG_CRYPTO_PCBC is not set +# CONFIG_CRYPTO_XTS is not set + +# +# Hash modes +# +CONFIG_CRYPTO_HMAC=m +# CONFIG_CRYPTO_XCBC is not set + +# +# Digest +# +# CONFIG_CRYPTO_CRC32C is not set +# CONFIG_CRYPTO_MD4 is not set +CONFIG_CRYPTO_MD5=m +# CONFIG_CRYPTO_MICHAEL_MIC is not set +CONFIG_CRYPTO_SHA1=m +# CONFIG_CRYPTO_SHA256 is not set +# CONFIG_CRYPTO_SHA512 is not set +# CONFIG_CRYPTO_TGR192 is not set +# CONFIG_CRYPTO_WP512 is not set + +# +# Ciphers +# +CONFIG_CRYPTO_AES=m +# CONFIG_CRYPTO_ANUBIS is not set +CONFIG_CRYPTO_ARC4=m +# CONFIG_CRYPTO_BLOWFISH is not set +# CONFIG_CRYPTO_CAMELLIA is not set +# CONFIG_CRYPTO_CAST5 is not set +# CONFIG_CRYPTO_CAST6 is not set +CONFIG_CRYPTO_DES=m +# CONFIG_CRYPTO_FCRYPT is not set +# CONFIG_CRYPTO_KHAZAD is not set +# CONFIG_CRYPTO_SALSA20 is not set +# CONFIG_CRYPTO_SEED is not set +# CONFIG_CRYPTO_SERPENT is not set +# CONFIG_CRYPTO_TEA is not set +# CONFIG_CRYPTO_TWOFISH is not set # -# Cryptographic options +# Compression # -# CONFIG_CRYPTO is not set +CONFIG_CRYPTO_DEFLATE=m +# CONFIG_CRYPTO_LZO is not set +CONFIG_CRYPTO_HW=y # # Library routines # CONFIG_BITREVERSE=y +# CONFIG_GENERIC_FIND_FIRST_BIT is not set +# CONFIG_GENERIC_FIND_NEXT_BIT is not set # CONFIG_CRC_CCITT is not set # CONFIG_CRC16 is not set +CONFIG_CRC_ITU_T=m CONFIG_CRC32=y +# CONFIG_CRC7 is not set # CONFIG_LIBCRC32C is not set CONFIG_ZLIB_INFLATE=y CONFIG_ZLIB_DEFLATE=y CONFIG_PLIST=y CONFIG_HAS_IOMEM=y +CONFIG_HAS_DMA=y diff --git a/arch/arm/configs/sam9_l9260_defconfig b/arch/arm/configs/sam9_l9260_defconfig index 484dc9739df..8688362bcf7 100644 --- a/arch/arm/configs/sam9_l9260_defconfig +++ b/arch/arm/configs/sam9_l9260_defconfig @@ -211,7 +211,6 @@ CONFIG_ARM_THUMB=y # # CONFIG_TICK_ONESHOT is not set CONFIG_PREEMPT=y -# CONFIG_NO_IDLE_HZ is not set CONFIG_HZ=100 # CONFIG_AEABI is not set # CONFIG_ARCH_DISCONTIGMEM_ENABLE is not set diff --git a/arch/arm/configs/spitz_defconfig b/arch/arm/configs/spitz_defconfig index aa7a0117950..7d59fb1f1ce 100644 --- a/arch/arm/configs/spitz_defconfig +++ b/arch/arm/configs/spitz_defconfig @@ -164,7 +164,6 @@ CONFIG_PCMCIA_PXA2XX=y # Kernel Features # CONFIG_PREEMPT=y -# CONFIG_NO_IDLE_HZ is not set # CONFIG_ARCH_DISCONTIGMEM_ENABLE is not set CONFIG_SELECT_MEMORY_MODEL=y CONFIG_FLATMEM_MANUAL=y diff --git a/arch/arm/configs/tct_hammer_defconfig b/arch/arm/configs/tct_hammer_defconfig index 576b8339f0d..07dfb98df4f 100644 --- a/arch/arm/configs/tct_hammer_defconfig +++ b/arch/arm/configs/tct_hammer_defconfig @@ -247,7 +247,6 @@ CONFIG_ARM_THUMB=y # # CONFIG_TICK_ONESHOT is not set # CONFIG_PREEMPT is not set -# CONFIG_NO_IDLE_HZ is not set CONFIG_HZ=200 # CONFIG_AEABI is not set # CONFIG_ARCH_DISCONTIGMEM_ENABLE is not set diff --git a/arch/arm/configs/trizeps4_defconfig b/arch/arm/configs/trizeps4_defconfig index 6db6392806f..8b7a431a8bf 100644 --- a/arch/arm/configs/trizeps4_defconfig +++ b/arch/arm/configs/trizeps4_defconfig @@ -195,7 +195,6 @@ CONFIG_PCMCIA_PXA2XX=y # Kernel Features # CONFIG_PREEMPT=y -# CONFIG_NO_IDLE_HZ is not set CONFIG_HZ=100 CONFIG_AEABI=y CONFIG_OABI_COMPAT=y diff --git a/arch/arm/configs/usb-a9260_defconfig b/arch/arm/configs/usb-a9260_defconfig new file mode 100644 index 00000000000..3680bd2df26 --- /dev/null +++ b/arch/arm/configs/usb-a9260_defconfig @@ -0,0 +1,1142 @@ +# +# Automatically generated make config: don't edit +# Linux kernel version: 2.6.24 +# Tue Apr 15 11:39:35 2008 +# +CONFIG_ARM=y +CONFIG_SYS_SUPPORTS_APM_EMULATION=y +CONFIG_GENERIC_GPIO=y +CONFIG_GENERIC_TIME=y +CONFIG_GENERIC_CLOCKEVENTS=y +CONFIG_MMU=y +# CONFIG_NO_IOPORT is not set +CONFIG_GENERIC_HARDIRQS=y +CONFIG_STACKTRACE_SUPPORT=y +CONFIG_LOCKDEP_SUPPORT=y +CONFIG_TRACE_IRQFLAGS_SUPPORT=y +CONFIG_HARDIRQS_SW_RESEND=y +CONFIG_GENERIC_IRQ_PROBE=y +CONFIG_RWSEM_GENERIC_SPINLOCK=y +# CONFIG_ARCH_HAS_ILOG2_U32 is not set +# CONFIG_ARCH_HAS_ILOG2_U64 is not set +CONFIG_GENERIC_HWEIGHT=y +CONFIG_GENERIC_CALIBRATE_DELAY=y +CONFIG_ZONE_DMA=y +CONFIG_VECTORS_BASE=0xffff0000 +CONFIG_DEFCONFIG_LIST="/lib/modules/$UNAME_RELEASE/.config" + +# +# General setup +# +CONFIG_EXPERIMENTAL=y +CONFIG_BROKEN_ON_SMP=y +CONFIG_INIT_ENV_ARG_LIMIT=32 +CONFIG_LOCALVERSION="" +# CONFIG_LOCALVERSION_AUTO is not set +# CONFIG_SWAP is not set +CONFIG_SYSVIPC=y +CONFIG_SYSVIPC_SYSCTL=y +# CONFIG_POSIX_MQUEUE is not set +# CONFIG_BSD_PROCESS_ACCT is not set +# CONFIG_TASKSTATS is not set +# CONFIG_USER_NS is not set +# CONFIG_PID_NS is not set +# CONFIG_AUDIT is not set +# CONFIG_IKCONFIG is not set +CONFIG_LOG_BUF_SHIFT=14 +# CONFIG_CGROUPS is not set +CONFIG_FAIR_GROUP_SCHED=y +CONFIG_FAIR_USER_SCHED=y +# CONFIG_FAIR_CGROUP_SCHED is not set +# CONFIG_SYSFS_DEPRECATED is not set +# CONFIG_RELAY is not set +# CONFIG_BLK_DEV_INITRD is not set +# CONFIG_CC_OPTIMIZE_FOR_SIZE is not set +CONFIG_SYSCTL=y +# CONFIG_EMBEDDED is not set +CONFIG_UID16=y +CONFIG_SYSCTL_SYSCALL=y +CONFIG_KALLSYMS=y +# CONFIG_KALLSYMS_ALL is not set +# CONFIG_KALLSYMS_EXTRA_PASS is not set +CONFIG_HOTPLUG=y +CONFIG_PRINTK=y +CONFIG_BUG=y +CONFIG_ELF_CORE=y +CONFIG_BASE_FULL=y +CONFIG_FUTEX=y +CONFIG_ANON_INODES=y +CONFIG_EPOLL=y +CONFIG_SIGNALFD=y +CONFIG_EVENTFD=y +CONFIG_SHMEM=y +CONFIG_VM_EVENT_COUNTERS=y +CONFIG_SLAB=y +# CONFIG_SLUB is not set +# CONFIG_SLOB is not set +CONFIG_SLABINFO=y +CONFIG_RT_MUTEXES=y +# CONFIG_TINY_SHMEM is not set +CONFIG_BASE_SMALL=0 +CONFIG_MODULES=y +CONFIG_MODULE_UNLOAD=y +# CONFIG_MODULE_FORCE_UNLOAD is not set +# CONFIG_MODVERSIONS is not set +# CONFIG_MODULE_SRCVERSION_ALL is not set +CONFIG_KMOD=y +CONFIG_BLOCK=y +# CONFIG_LBD is not set +# CONFIG_BLK_DEV_IO_TRACE is not set +# CONFIG_LSF is not set +# CONFIG_BLK_DEV_BSG is not set + +# +# IO Schedulers +# +CONFIG_IOSCHED_NOOP=y +CONFIG_IOSCHED_AS=y +# CONFIG_IOSCHED_DEADLINE is not set +# CONFIG_IOSCHED_CFQ is not set +CONFIG_DEFAULT_AS=y +# CONFIG_DEFAULT_DEADLINE is not set +# CONFIG_DEFAULT_CFQ is not set +# CONFIG_DEFAULT_NOOP is not set +CONFIG_DEFAULT_IOSCHED="anticipatory" + +# +# System Type +# +# CONFIG_ARCH_AAEC2000 is not set +# CONFIG_ARCH_INTEGRATOR is not set +# CONFIG_ARCH_REALVIEW is not set +# CONFIG_ARCH_VERSATILE is not set +CONFIG_ARCH_AT91=y +# CONFIG_ARCH_CLPS7500 is not set +# CONFIG_ARCH_CLPS711X is not set +# CONFIG_ARCH_CO285 is not set +# CONFIG_ARCH_EBSA110 is not set +# CONFIG_ARCH_EP93XX is not set +# CONFIG_ARCH_FOOTBRIDGE is not set +# CONFIG_ARCH_NETX is not set +# CONFIG_ARCH_H720X is not set +# CONFIG_ARCH_IMX is not set +# CONFIG_ARCH_IOP13XX is not set +# CONFIG_ARCH_IOP32X is not set +# CONFIG_ARCH_IOP33X is not set +# CONFIG_ARCH_IXP23XX is not set +# CONFIG_ARCH_IXP2000 is not set +# CONFIG_ARCH_IXP4XX is not set +# CONFIG_ARCH_L7200 is not set +# CONFIG_ARCH_KS8695 is not set +# CONFIG_ARCH_NS9XXX is not set +# CONFIG_ARCH_MXC is not set +# CONFIG_ARCH_PNX4008 is not set +# CONFIG_ARCH_PXA is not set +# CONFIG_ARCH_RPC is not set +# CONFIG_ARCH_SA1100 is not set +# CONFIG_ARCH_S3C2410 is not set +# CONFIG_ARCH_SHARK is not set +# CONFIG_ARCH_LH7A40X is not set +# CONFIG_ARCH_DAVINCI is not set +# CONFIG_ARCH_OMAP is not set + +# +# Boot options +# + +# +# Power management +# + +# +# Atmel AT91 System-on-Chip +# +# CONFIG_ARCH_AT91RM9200 is not set +CONFIG_ARCH_AT91SAM9260=y +# CONFIG_ARCH_AT91SAM9261 is not set +# CONFIG_ARCH_AT91SAM9263 is not set +# CONFIG_ARCH_AT91SAM9RL is not set +# CONFIG_ARCH_AT91CAP9 is not set +# CONFIG_ARCH_AT91X40 is not set +CONFIG_AT91_PMC_UNIT=y + +# +# AT91SAM9260 Variants +# +# CONFIG_ARCH_AT91SAM9260_SAM9XE is not set + +# +# AT91SAM9260 / AT91SAM9XE Board Type +# +# CONFIG_MACH_AT91SAM9260EK is not set +# CONFIG_MACH_CAM60 is not set +# CONFIG_MACH_SAM9_L9260 is not set +CONFIG_MACH_USB_A9260=y +# CONFIG_MACH_QIL_A9260 is not set + +# +# AT91 Board Options +# + +# +# AT91 Feature Selections +# +# CONFIG_AT91_PROGRAMMABLE_CLOCKS is not set +CONFIG_AT91_SLOW_CLOCK=y +CONFIG_AT91_TIMER_HZ=100 +CONFIG_AT91_EARLY_DBGU=y +# CONFIG_AT91_EARLY_USART0 is not set +# CONFIG_AT91_EARLY_USART1 is not set +# CONFIG_AT91_EARLY_USART2 is not set +# CONFIG_AT91_EARLY_USART3 is not set +# CONFIG_AT91_EARLY_USART4 is not set +# CONFIG_AT91_EARLY_USART5 is not set + +# +# Processor Type +# +CONFIG_CPU_32=y +CONFIG_CPU_ARM926T=y +CONFIG_CPU_32v5=y +CONFIG_CPU_ABRT_EV5TJ=y +CONFIG_CPU_CACHE_VIVT=y +CONFIG_CPU_COPY_V4WB=y +CONFIG_CPU_TLB_V4WBI=y +CONFIG_CPU_CP15=y +CONFIG_CPU_CP15_MMU=y + +# +# Processor Features +# +# CONFIG_ARM_THUMB is not set +# CONFIG_CPU_ICACHE_DISABLE is not set +# CONFIG_CPU_DCACHE_DISABLE is not set +# CONFIG_CPU_DCACHE_WRITETHROUGH is not set +# CONFIG_CPU_CACHE_ROUND_ROBIN is not set +# CONFIG_OUTER_CACHE is not set + +# +# Bus support +# +# CONFIG_PCI_SYSCALL is not set +# CONFIG_ARCH_SUPPORTS_MSI is not set +# CONFIG_PCCARD is not set + +# +# Kernel Features +# +# CONFIG_TICK_ONESHOT is not set +# CONFIG_NO_HZ is not set +# CONFIG_HIGH_RES_TIMERS is not set +CONFIG_GENERIC_CLOCKEVENTS_BUILD=y +# CONFIG_PREEMPT is not set +CONFIG_HZ=100 +CONFIG_AEABI=y +CONFIG_OABI_COMPAT=y +# CONFIG_ARCH_DISCONTIGMEM_ENABLE is not set +CONFIG_SELECT_MEMORY_MODEL=y +CONFIG_FLATMEM_MANUAL=y +# CONFIG_DISCONTIGMEM_MANUAL is not set +# CONFIG_SPARSEMEM_MANUAL is not set +CONFIG_FLATMEM=y +CONFIG_FLAT_NODE_MEM_MAP=y +# CONFIG_SPARSEMEM_STATIC is not set +# CONFIG_SPARSEMEM_VMEMMAP_ENABLE is not set +CONFIG_SPLIT_PTLOCK_CPUS=4096 +# CONFIG_RESOURCES_64BIT is not set +CONFIG_ZONE_DMA_FLAG=1 +CONFIG_BOUNCE=y +CONFIG_VIRT_TO_BUS=y +# CONFIG_LEDS is not set +CONFIG_ALIGNMENT_TRAP=y + +# +# Boot options +# +CONFIG_ZBOOT_ROM_TEXT=0x0 +CONFIG_ZBOOT_ROM_BSS=0x0 +CONFIG_CMDLINE="mem=64M console=ttyS0,115200" +# CONFIG_XIP_KERNEL is not set +# CONFIG_KEXEC is not set + +# +# Floating point emulation +# + +# +# At least one emulation must be selected +# +CONFIG_FPE_NWFPE=y +# CONFIG_FPE_NWFPE_XP is not set +# CONFIG_FPE_FASTFPE is not set +# CONFIG_VFP is not set + +# +# Userspace binary formats +# +CONFIG_BINFMT_ELF=y +# CONFIG_BINFMT_AOUT is not set +# CONFIG_BINFMT_MISC is not set + +# +# Power management options +# +CONFIG_PM=y +# CONFIG_PM_LEGACY is not set +# CONFIG_PM_DEBUG is not set +CONFIG_PM_SLEEP=y +CONFIG_SUSPEND_UP_POSSIBLE=y +CONFIG_SUSPEND=y +# CONFIG_APM_EMULATION is not set + +# +# Networking +# +CONFIG_NET=y + +# +# Networking options +# +CONFIG_PACKET=y +# CONFIG_PACKET_MMAP is not set +CONFIG_UNIX=y +# CONFIG_NET_KEY is not set +CONFIG_INET=y +CONFIG_IP_MULTICAST=y +CONFIG_IP_ADVANCED_ROUTER=y +CONFIG_ASK_IP_FIB_HASH=y +# CONFIG_IP_FIB_TRIE is not set +CONFIG_IP_FIB_HASH=y +# CONFIG_IP_MULTIPLE_TABLES is not set +# CONFIG_IP_ROUTE_MULTIPATH is not set +CONFIG_IP_ROUTE_VERBOSE=y +CONFIG_IP_PNP=y +# CONFIG_IP_PNP_DHCP is not set +CONFIG_IP_PNP_BOOTP=y +CONFIG_IP_PNP_RARP=y +# CONFIG_NET_IPIP is not set +# CONFIG_NET_IPGRE is not set +CONFIG_IP_MROUTE=y +CONFIG_IP_PIMSM_V1=y +CONFIG_IP_PIMSM_V2=y +# CONFIG_ARPD is not set +# CONFIG_SYN_COOKIES is not set +# CONFIG_INET_AH is not set +# CONFIG_INET_ESP is not set +# CONFIG_INET_IPCOMP is not set +# CONFIG_INET_XFRM_TUNNEL is not set +# CONFIG_INET_TUNNEL is not set +# CONFIG_INET_XFRM_MODE_TRANSPORT is not set +# CONFIG_INET_XFRM_MODE_TUNNEL is not set +# CONFIG_INET_XFRM_MODE_BEET is not set +# CONFIG_INET_LRO is not set +# CONFIG_INET_DIAG is not set +# CONFIG_TCP_CONG_ADVANCED is not set +CONFIG_TCP_CONG_CUBIC=y +CONFIG_DEFAULT_TCP_CONG="cubic" +# CONFIG_TCP_MD5SIG is not set +# CONFIG_IPV6 is not set +# CONFIG_INET6_XFRM_TUNNEL is not set +# CONFIG_INET6_TUNNEL is not set +# CONFIG_NETWORK_SECMARK is not set +# CONFIG_NETFILTER is not set +# CONFIG_IP_DCCP is not set +# CONFIG_IP_SCTP is not set +# CONFIG_TIPC is not set +# CONFIG_ATM is not set +# CONFIG_BRIDGE is not set +# CONFIG_VLAN_8021Q is not set +# CONFIG_DECNET is not set +# CONFIG_LLC2 is not set +# CONFIG_IPX is not set +# CONFIG_ATALK is not set +# CONFIG_X25 is not set +# CONFIG_LAPB is not set +# CONFIG_ECONET is not set +# CONFIG_WAN_ROUTER is not set +# CONFIG_NET_SCHED is not set + +# +# Network testing +# +# CONFIG_NET_PKTGEN is not set +# CONFIG_HAMRADIO is not set +# CONFIG_IRDA is not set +# CONFIG_BT is not set +# CONFIG_AF_RXRPC is not set + +# +# Wireless +# +# CONFIG_CFG80211 is not set +# CONFIG_WIRELESS_EXT is not set +# CONFIG_MAC80211 is not set +# CONFIG_IEEE80211 is not set +# CONFIG_RFKILL is not set +# CONFIG_NET_9P is not set + +# +# Device Drivers +# + +# +# Generic Driver Options +# +CONFIG_UEVENT_HELPER_PATH="/sbin/hotplug" +CONFIG_STANDALONE=y +CONFIG_PREVENT_FIRMWARE_BUILD=y +# CONFIG_FW_LOADER is not set +# CONFIG_DEBUG_DRIVER is not set +# CONFIG_DEBUG_DEVRES is not set +# CONFIG_SYS_HYPERVISOR is not set +# CONFIG_CONNECTOR is not set +CONFIG_MTD=y +# CONFIG_MTD_DEBUG is not set +# CONFIG_MTD_CONCAT is not set +CONFIG_MTD_PARTITIONS=y +# CONFIG_MTD_REDBOOT_PARTS is not set +CONFIG_MTD_CMDLINE_PARTS=y +# CONFIG_MTD_AFS_PARTS is not set + +# +# User Modules And Translation Layers +# +CONFIG_MTD_CHAR=y +CONFIG_MTD_BLKDEVS=y +CONFIG_MTD_BLOCK=y +# CONFIG_FTL is not set +# CONFIG_NFTL is not set +# CONFIG_INFTL is not set +# CONFIG_RFD_FTL is not set +# CONFIG_SSFDC is not set +# CONFIG_MTD_OOPS is not set + +# +# RAM/ROM/Flash chip drivers +# +# CONFIG_MTD_CFI is not set +# CONFIG_MTD_JEDECPROBE is not set +CONFIG_MTD_MAP_BANK_WIDTH_1=y +CONFIG_MTD_MAP_BANK_WIDTH_2=y +CONFIG_MTD_MAP_BANK_WIDTH_4=y +# CONFIG_MTD_MAP_BANK_WIDTH_8 is not set +# CONFIG_MTD_MAP_BANK_WIDTH_16 is not set +# CONFIG_MTD_MAP_BANK_WIDTH_32 is not set +CONFIG_MTD_CFI_I1=y +CONFIG_MTD_CFI_I2=y +# CONFIG_MTD_CFI_I4 is not set +# CONFIG_MTD_CFI_I8 is not set +# CONFIG_MTD_RAM is not set +# CONFIG_MTD_ROM is not set +# CONFIG_MTD_ABSENT is not set + +# +# Mapping drivers for chip access +# +# CONFIG_MTD_COMPLEX_MAPPINGS is not set +# CONFIG_MTD_PLATRAM is not set + +# +# Self-contained MTD device drivers +# +CONFIG_MTD_DATAFLASH=y +# CONFIG_MTD_M25P80 is not set +# CONFIG_MTD_SLRAM is not set +# CONFIG_MTD_PHRAM is not set +# CONFIG_MTD_MTDRAM is not set +# CONFIG_MTD_BLOCK2MTD is not set + +# +# Disk-On-Chip Device Drivers +# +# CONFIG_MTD_DOC2000 is not set +# CONFIG_MTD_DOC2001 is not set +# CONFIG_MTD_DOC2001PLUS is not set +CONFIG_MTD_NAND=y +# CONFIG_MTD_NAND_VERIFY_WRITE is not set +# CONFIG_MTD_NAND_ECC_SMC is not set +# CONFIG_MTD_NAND_MUSEUM_IDS is not set +CONFIG_MTD_NAND_IDS=y +# CONFIG_MTD_NAND_DISKONCHIP is not set +CONFIG_MTD_NAND_AT91=y +CONFIG_MTD_NAND_AT91_ECC_SOFT=y +# CONFIG_MTD_NAND_AT91_ECC_HW is not set +# CONFIG_MTD_NAND_AT91_ECC_NONE is not set +# CONFIG_MTD_NAND_NANDSIM is not set +# CONFIG_MTD_NAND_PLATFORM is not set +# CONFIG_MTD_ALAUDA is not set +# CONFIG_MTD_ONENAND is not set + +# +# UBI - Unsorted block images +# +# CONFIG_MTD_UBI is not set +# CONFIG_PARPORT is not set +CONFIG_BLK_DEV=y +# CONFIG_BLK_DEV_COW_COMMON is not set +CONFIG_BLK_DEV_LOOP=y +# CONFIG_BLK_DEV_CRYPTOLOOP is not set +# CONFIG_BLK_DEV_NBD is not set +# CONFIG_BLK_DEV_UB is not set +# CONFIG_BLK_DEV_RAM is not set +# CONFIG_CDROM_PKTCDVD is not set +# CONFIG_ATA_OVER_ETH is not set +# CONFIG_MISC_DEVICES is not set + +# +# SCSI device support +# +# CONFIG_RAID_ATTRS is not set +CONFIG_SCSI=y +CONFIG_SCSI_DMA=y +# CONFIG_SCSI_TGT is not set +# CONFIG_SCSI_NETLINK is not set +CONFIG_SCSI_PROC_FS=y + +# +# SCSI support type (disk, tape, CD-ROM) +# +CONFIG_BLK_DEV_SD=y +# CONFIG_CHR_DEV_ST is not set +# CONFIG_CHR_DEV_OSST is not set +# CONFIG_BLK_DEV_SR is not set +# CONFIG_CHR_DEV_SG is not set +# CONFIG_CHR_DEV_SCH is not set + +# +# Some SCSI devices (e.g. CD jukebox) support multiple LUNs +# +CONFIG_SCSI_MULTI_LUN=y +# CONFIG_SCSI_CONSTANTS is not set +# CONFIG_SCSI_LOGGING is not set +# CONFIG_SCSI_SCAN_ASYNC is not set +CONFIG_SCSI_WAIT_SCAN=m + +# +# SCSI Transports +# +# CONFIG_SCSI_SPI_ATTRS is not set +# CONFIG_SCSI_FC_ATTRS is not set +# CONFIG_SCSI_ISCSI_ATTRS is not set +# CONFIG_SCSI_SAS_LIBSAS is not set +# CONFIG_SCSI_SRP_ATTRS is not set +CONFIG_SCSI_LOWLEVEL=y +# CONFIG_ISCSI_TCP is not set +# CONFIG_SCSI_DEBUG is not set +# CONFIG_ATA is not set +# CONFIG_MD is not set +CONFIG_NETDEVICES=y +# CONFIG_NETDEVICES_MULTIQUEUE is not set +# CONFIG_DUMMY is not set +# CONFIG_BONDING is not set +# CONFIG_MACVLAN is not set +# CONFIG_EQUALIZER is not set +# CONFIG_TUN is not set +# CONFIG_VETH is not set +CONFIG_PHYLIB=y + +# +# MII PHY device drivers +# +# CONFIG_MARVELL_PHY is not set +# CONFIG_DAVICOM_PHY is not set +# CONFIG_QSEMI_PHY is not set +# CONFIG_LXT_PHY is not set +# CONFIG_CICADA_PHY is not set +# CONFIG_VITESSE_PHY is not set +# CONFIG_SMSC_PHY is not set +# CONFIG_BROADCOM_PHY is not set +# CONFIG_ICPLUS_PHY is not set +# CONFIG_FIXED_PHY is not set +# CONFIG_MDIO_BITBANG is not set +CONFIG_NET_ETHERNET=y +CONFIG_MII=y +CONFIG_MACB=y +# CONFIG_AX88796 is not set +# CONFIG_SMC91X is not set +# CONFIG_DM9000 is not set +# CONFIG_IBM_NEW_EMAC_ZMII is not set +# CONFIG_IBM_NEW_EMAC_RGMII is not set +# CONFIG_IBM_NEW_EMAC_TAH is not set +# CONFIG_IBM_NEW_EMAC_EMAC4 is not set +# CONFIG_B44 is not set +CONFIG_NETDEV_1000=y +CONFIG_NETDEV_10000=y + +# +# Wireless LAN +# +# CONFIG_WLAN_PRE80211 is not set +# CONFIG_WLAN_80211 is not set + +# +# USB Network Adapters +# +# CONFIG_USB_CATC is not set +# CONFIG_USB_KAWETH is not set +# CONFIG_USB_PEGASUS is not set +# CONFIG_USB_RTL8150 is not set +# CONFIG_USB_USBNET is not set +# CONFIG_WAN is not set +# CONFIG_PPP is not set +# CONFIG_SLIP is not set +# CONFIG_SHAPER is not set +# CONFIG_NETCONSOLE is not set +# CONFIG_NETPOLL is not set +# CONFIG_NET_POLL_CONTROLLER is not set +# CONFIG_ISDN is not set + +# +# Input device support +# +CONFIG_INPUT=y +# CONFIG_INPUT_FF_MEMLESS is not set +# CONFIG_INPUT_POLLDEV is not set + +# +# Userland interfaces +# +CONFIG_INPUT_MOUSEDEV=y +# CONFIG_INPUT_MOUSEDEV_PSAUX is not set +CONFIG_INPUT_MOUSEDEV_SCREEN_X=1024 +CONFIG_INPUT_MOUSEDEV_SCREEN_Y=768 +# CONFIG_INPUT_JOYDEV is not set +CONFIG_INPUT_EVDEV=y +CONFIG_INPUT_EVBUG=y + +# +# Input Device Drivers +# +CONFIG_INPUT_KEYBOARD=y +# CONFIG_KEYBOARD_ATKBD is not set +# CONFIG_KEYBOARD_SUNKBD is not set +# CONFIG_KEYBOARD_LKKBD is not set +# CONFIG_KEYBOARD_XTKBD is not set +# CONFIG_KEYBOARD_NEWTON is not set +# CONFIG_KEYBOARD_STOWAWAY is not set +CONFIG_KEYBOARD_GPIO=y +# CONFIG_INPUT_MOUSE is not set +# CONFIG_INPUT_JOYSTICK is not set +# CONFIG_INPUT_TABLET is not set +# CONFIG_INPUT_TOUCHSCREEN is not set +# CONFIG_INPUT_MISC is not set + +# +# Hardware I/O ports +# +# CONFIG_SERIO is not set +# CONFIG_GAMEPORT is not set + +# +# Character devices +# +CONFIG_VT=y +CONFIG_VT_CONSOLE=y +CONFIG_HW_CONSOLE=y +# CONFIG_VT_HW_CONSOLE_BINDING is not set +# CONFIG_SERIAL_NONSTANDARD is not set + +# +# Serial drivers +# +# CONFIG_SERIAL_8250 is not set + +# +# Non-8250 serial port support +# +CONFIG_SERIAL_ATMEL=y +CONFIG_SERIAL_ATMEL_CONSOLE=y +# CONFIG_SERIAL_ATMEL_TTYAT is not set +CONFIG_SERIAL_CORE=y +CONFIG_SERIAL_CORE_CONSOLE=y +CONFIG_UNIX98_PTYS=y +CONFIG_LEGACY_PTYS=y +CONFIG_LEGACY_PTY_COUNT=256 +# CONFIG_IPMI_HANDLER is not set +CONFIG_HW_RANDOM=y +# CONFIG_NVRAM is not set +# CONFIG_R3964 is not set +# CONFIG_RAW_DRIVER is not set +# CONFIG_TCG_TPM is not set +# CONFIG_I2C is not set + +# +# SPI support +# +CONFIG_SPI=y +# CONFIG_SPI_DEBUG is not set +CONFIG_SPI_MASTER=y + +# +# SPI Master Controller Drivers +# +CONFIG_SPI_ATMEL=y +# CONFIG_SPI_BITBANG is not set + +# +# SPI Protocol Masters +# +# CONFIG_SPI_AT25 is not set +# CONFIG_SPI_SPIDEV is not set +# CONFIG_SPI_TLE62X0 is not set +# CONFIG_W1 is not set +# CONFIG_POWER_SUPPLY is not set +# CONFIG_HWMON is not set +# CONFIG_WATCHDOG is not set + +# +# Sonics Silicon Backplane +# +CONFIG_SSB_POSSIBLE=y +# CONFIG_SSB is not set + +# +# Multifunction device drivers +# +# CONFIG_MFD_SM501 is not set + +# +# Multimedia devices +# +# CONFIG_VIDEO_DEV is not set +# CONFIG_DVB_CORE is not set +# CONFIG_DAB is not set + +# +# Graphics support +# +# CONFIG_VGASTATE is not set +# CONFIG_VIDEO_OUTPUT_CONTROL is not set +# CONFIG_FB is not set +# CONFIG_BACKLIGHT_LCD_SUPPORT is not set + +# +# Display device support +# +# CONFIG_DISPLAY_SUPPORT is not set + +# +# Console display driver support +# +# CONFIG_VGA_CONSOLE is not set +CONFIG_DUMMY_CONSOLE=y + +# +# Sound +# +# CONFIG_SOUND is not set +CONFIG_HID_SUPPORT=y +CONFIG_HID=y +# CONFIG_HID_DEBUG is not set +# CONFIG_HIDRAW is not set + +# +# USB Input Devices +# +# CONFIG_USB_HID is not set + +# +# USB HID Boot Protocol drivers +# +# CONFIG_USB_KBD is not set +# CONFIG_USB_MOUSE is not set +CONFIG_USB_SUPPORT=y +CONFIG_USB_ARCH_HAS_HCD=y +CONFIG_USB_ARCH_HAS_OHCI=y +# CONFIG_USB_ARCH_HAS_EHCI is not set +CONFIG_USB=y +# CONFIG_USB_DEBUG is not set + +# +# Miscellaneous USB options +# +CONFIG_USB_DEVICEFS=y +CONFIG_USB_DEVICE_CLASS=y +# CONFIG_USB_DYNAMIC_MINORS is not set +# CONFIG_USB_SUSPEND is not set +# CONFIG_USB_PERSIST is not set +# CONFIG_USB_OTG is not set + +# +# USB Host Controller Drivers +# +# CONFIG_USB_ISP116X_HCD is not set +CONFIG_USB_OHCI_HCD=y +# CONFIG_USB_OHCI_BIG_ENDIAN_DESC is not set +# CONFIG_USB_OHCI_BIG_ENDIAN_MMIO is not set +CONFIG_USB_OHCI_LITTLE_ENDIAN=y +# CONFIG_USB_SL811_HCD is not set +# CONFIG_USB_R8A66597_HCD is not set + +# +# USB Device Class drivers +# +# CONFIG_USB_ACM is not set +# CONFIG_USB_PRINTER is not set + +# +# NOTE: USB_STORAGE enables SCSI, and 'SCSI disk support' +# + +# +# may also be needed; see USB_STORAGE Help for more information +# +CONFIG_USB_STORAGE=y +# CONFIG_USB_STORAGE_DEBUG is not set +# CONFIG_USB_STORAGE_DATAFAB is not set +# CONFIG_USB_STORAGE_FREECOM is not set +# CONFIG_USB_STORAGE_ISD200 is not set +# CONFIG_USB_STORAGE_DPCM is not set +# CONFIG_USB_STORAGE_USBAT is not set +# CONFIG_USB_STORAGE_SDDR09 is not set +# CONFIG_USB_STORAGE_SDDR55 is not set +# CONFIG_USB_STORAGE_JUMPSHOT is not set +# CONFIG_USB_STORAGE_ALAUDA is not set +# CONFIG_USB_STORAGE_KARMA is not set +# CONFIG_USB_LIBUSUAL is not set + +# +# USB Imaging devices +# +# CONFIG_USB_MDC800 is not set +# CONFIG_USB_MICROTEK is not set +CONFIG_USB_MON=y + +# +# USB port drivers +# + +# +# USB Serial Converter support +# +# CONFIG_USB_SERIAL is not set + +# +# USB Miscellaneous drivers +# +# CONFIG_USB_EMI62 is not set +# CONFIG_USB_EMI26 is not set +# CONFIG_USB_ADUTUX is not set +# CONFIG_USB_AUERSWALD is not set +# CONFIG_USB_RIO500 is not set +# CONFIG_USB_LEGOTOWER is not set +# CONFIG_USB_LCD is not set +# CONFIG_USB_BERRY_CHARGE is not set +# CONFIG_USB_LED is not set +# CONFIG_USB_CYPRESS_CY7C63 is not set +# CONFIG_USB_CYTHERM is not set +# CONFIG_USB_PHIDGET is not set +# CONFIG_USB_IDMOUSE is not set +# CONFIG_USB_FTDI_ELAN is not set +# CONFIG_USB_APPLEDISPLAY is not set +# CONFIG_USB_LD is not set +# CONFIG_USB_TRANCEVIBRATOR is not set +# CONFIG_USB_IOWARRIOR is not set +# CONFIG_USB_TEST is not set + +# +# USB DSL modem support +# + +# +# USB Gadget Support +# +CONFIG_USB_GADGET=y +# CONFIG_USB_GADGET_DEBUG is not set +# CONFIG_USB_GADGET_DEBUG_FILES is not set +CONFIG_USB_GADGET_SELECTED=y +# CONFIG_USB_GADGET_AMD5536UDC is not set +# CONFIG_USB_GADGET_ATMEL_USBA is not set +# CONFIG_USB_GADGET_FSL_USB2 is not set +# CONFIG_USB_GADGET_NET2280 is not set +# CONFIG_USB_GADGET_PXA2XX is not set +# CONFIG_USB_GADGET_M66592 is not set +# CONFIG_USB_GADGET_GOKU is not set +# CONFIG_USB_GADGET_LH7A40X is not set +# CONFIG_USB_GADGET_OMAP is not set +# CONFIG_USB_GADGET_S3C2410 is not set +CONFIG_USB_GADGET_AT91=y +CONFIG_USB_AT91=y +# CONFIG_USB_GADGET_DUMMY_HCD is not set +# CONFIG_USB_GADGET_DUALSPEED is not set +# CONFIG_USB_ZERO is not set +CONFIG_USB_ETH=y +CONFIG_USB_ETH_RNDIS=y +# CONFIG_USB_GADGETFS is not set +# CONFIG_USB_FILE_STORAGE is not set +# CONFIG_USB_G_SERIAL is not set +# CONFIG_USB_MIDI_GADGET is not set +# CONFIG_MMC is not set +CONFIG_NEW_LEDS=y +CONFIG_LEDS_CLASS=y + +# +# LED drivers +# +CONFIG_LEDS_GPIO=y + +# +# LED Triggers +# +CONFIG_LEDS_TRIGGERS=y +# CONFIG_LEDS_TRIGGER_TIMER is not set +CONFIG_LEDS_TRIGGER_HEARTBEAT=y +CONFIG_RTC_LIB=y +# CONFIG_RTC_CLASS is not set + +# +# File systems +# +CONFIG_EXT2_FS=y +# CONFIG_EXT2_FS_XATTR is not set +# CONFIG_EXT2_FS_XIP is not set +# CONFIG_EXT3_FS is not set +# CONFIG_EXT4DEV_FS is not set +# CONFIG_REISERFS_FS is not set +# CONFIG_JFS_FS is not set +CONFIG_FS_POSIX_ACL=y +# CONFIG_XFS_FS is not set +# CONFIG_GFS2_FS is not set +# CONFIG_OCFS2_FS is not set +# CONFIG_MINIX_FS is not set +# CONFIG_ROMFS_FS is not set +CONFIG_INOTIFY=y +CONFIG_INOTIFY_USER=y +# CONFIG_QUOTA is not set +CONFIG_DNOTIFY=y +# CONFIG_AUTOFS_FS is not set +# CONFIG_AUTOFS4_FS is not set +CONFIG_FUSE_FS=m + +# +# CD-ROM/DVD Filesystems +# +# CONFIG_ISO9660_FS is not set +# CONFIG_UDF_FS is not set + +# +# DOS/FAT/NT Filesystems +# +CONFIG_FAT_FS=y +# CONFIG_MSDOS_FS is not set +CONFIG_VFAT_FS=y +CONFIG_FAT_DEFAULT_CODEPAGE=437 +CONFIG_FAT_DEFAULT_IOCHARSET="iso8859-1" +# CONFIG_NTFS_FS is not set + +# +# Pseudo filesystems +# +CONFIG_PROC_FS=y +CONFIG_PROC_SYSCTL=y +CONFIG_SYSFS=y +CONFIG_TMPFS=y +# CONFIG_TMPFS_POSIX_ACL is not set +# CONFIG_HUGETLB_PAGE is not set +# CONFIG_CONFIGFS_FS is not set + +# +# Miscellaneous filesystems +# +# CONFIG_ADFS_FS is not set +# CONFIG_AFFS_FS is not set +# CONFIG_HFS_FS is not set +# CONFIG_HFSPLUS_FS is not set +# CONFIG_BEFS_FS is not set +# CONFIG_BFS_FS is not set +# CONFIG_EFS_FS is not set +CONFIG_JFFS2_FS=y +CONFIG_JFFS2_FS_DEBUG=0 +CONFIG_JFFS2_FS_WRITEBUFFER=y +# CONFIG_JFFS2_FS_WBUF_VERIFY is not set +# CONFIG_JFFS2_SUMMARY is not set +# CONFIG_JFFS2_FS_XATTR is not set +# CONFIG_JFFS2_COMPRESSION_OPTIONS is not set +CONFIG_JFFS2_ZLIB=y +# CONFIG_JFFS2_LZO is not set +CONFIG_JFFS2_RTIME=y +# CONFIG_JFFS2_RUBIN is not set +# CONFIG_CRAMFS is not set +# CONFIG_VXFS_FS is not set +# CONFIG_HPFS_FS is not set +# CONFIG_QNX4FS_FS is not set +# CONFIG_SYSV_FS is not set +# CONFIG_UFS_FS is not set +CONFIG_NETWORK_FILESYSTEMS=y +CONFIG_NFS_FS=y +CONFIG_NFS_V3=y +CONFIG_NFS_V3_ACL=y +CONFIG_NFS_V4=y +# CONFIG_NFS_DIRECTIO is not set +# CONFIG_NFSD is not set +CONFIG_ROOT_NFS=y +CONFIG_LOCKD=y +CONFIG_LOCKD_V4=y +CONFIG_NFS_ACL_SUPPORT=y +CONFIG_NFS_COMMON=y +CONFIG_SUNRPC=y +CONFIG_SUNRPC_GSS=y +# CONFIG_SUNRPC_BIND34 is not set +CONFIG_RPCSEC_GSS_KRB5=y +# CONFIG_RPCSEC_GSS_SPKM3 is not set +# CONFIG_SMB_FS is not set +# CONFIG_CIFS is not set +# CONFIG_NCP_FS is not set +# CONFIG_CODA_FS is not set +# CONFIG_AFS_FS is not set + +# +# Partition Types +# +# CONFIG_PARTITION_ADVANCED is not set +CONFIG_MSDOS_PARTITION=y +CONFIG_NLS=y +CONFIG_NLS_DEFAULT="iso8859-1" +CONFIG_NLS_CODEPAGE_437=y +# CONFIG_NLS_CODEPAGE_737 is not set +# CONFIG_NLS_CODEPAGE_775 is not set +CONFIG_NLS_CODEPAGE_850=y +# CONFIG_NLS_CODEPAGE_852 is not set +# CONFIG_NLS_CODEPAGE_855 is not set +# CONFIG_NLS_CODEPAGE_857 is not set +# CONFIG_NLS_CODEPAGE_860 is not set +# CONFIG_NLS_CODEPAGE_861 is not set +# CONFIG_NLS_CODEPAGE_862 is not set +# CONFIG_NLS_CODEPAGE_863 is not set +# CONFIG_NLS_CODEPAGE_864 is not set +# CONFIG_NLS_CODEPAGE_865 is not set +# CONFIG_NLS_CODEPAGE_866 is not set +# CONFIG_NLS_CODEPAGE_869 is not set +# CONFIG_NLS_CODEPAGE_936 is not set +# CONFIG_NLS_CODEPAGE_950 is not set +# CONFIG_NLS_CODEPAGE_932 is not set +# CONFIG_NLS_CODEPAGE_949 is not set +# CONFIG_NLS_CODEPAGE_874 is not set +# CONFIG_NLS_ISO8859_8 is not set +# CONFIG_NLS_CODEPAGE_1250 is not set +# CONFIG_NLS_CODEPAGE_1251 is not set +# CONFIG_NLS_ASCII is not set +CONFIG_NLS_ISO8859_1=y +# CONFIG_NLS_ISO8859_2 is not set +# CONFIG_NLS_ISO8859_3 is not set +# CONFIG_NLS_ISO8859_4 is not set +# CONFIG_NLS_ISO8859_5 is not set +# CONFIG_NLS_ISO8859_6 is not set +# CONFIG_NLS_ISO8859_7 is not set +# CONFIG_NLS_ISO8859_9 is not set +# CONFIG_NLS_ISO8859_13 is not set +# CONFIG_NLS_ISO8859_14 is not set +# CONFIG_NLS_ISO8859_15 is not set +# CONFIG_NLS_KOI8_R is not set +# CONFIG_NLS_KOI8_U is not set +# CONFIG_NLS_UTF8 is not set +# CONFIG_DLM is not set +# CONFIG_INSTRUMENTATION is not set + +# +# Kernel hacking +# +# CONFIG_PRINTK_TIME is not set +CONFIG_ENABLE_WARN_DEPRECATED=y +CONFIG_ENABLE_MUST_CHECK=y +# CONFIG_MAGIC_SYSRQ is not set +# CONFIG_UNUSED_SYMBOLS is not set +# CONFIG_DEBUG_FS is not set +# CONFIG_HEADERS_CHECK is not set +CONFIG_DEBUG_KERNEL=y +# CONFIG_DEBUG_SHIRQ is not set +CONFIG_DETECT_SOFTLOCKUP=y +CONFIG_SCHED_DEBUG=y +# CONFIG_SCHEDSTATS is not set +# CONFIG_TIMER_STATS is not set +# CONFIG_DEBUG_SLAB is not set +# CONFIG_DEBUG_RT_MUTEXES is not set +# CONFIG_RT_MUTEX_TESTER is not set +# CONFIG_DEBUG_SPINLOCK is not set +# CONFIG_DEBUG_MUTEXES is not set +# CONFIG_DEBUG_LOCK_ALLOC is not set +# CONFIG_PROVE_LOCKING is not set +# CONFIG_LOCK_STAT is not set +# CONFIG_DEBUG_SPINLOCK_SLEEP is not set +# CONFIG_DEBUG_LOCKING_API_SELFTESTS is not set +# CONFIG_DEBUG_KOBJECT is not set +CONFIG_DEBUG_BUGVERBOSE=y +# CONFIG_DEBUG_INFO is not set +# CONFIG_DEBUG_VM is not set +# CONFIG_DEBUG_LIST is not set +# CONFIG_DEBUG_SG is not set +CONFIG_FRAME_POINTER=y +CONFIG_FORCED_INLINING=y +# CONFIG_BOOT_PRINTK_DELAY is not set +# CONFIG_RCU_TORTURE_TEST is not set +# CONFIG_FAULT_INJECTION is not set +# CONFIG_SAMPLES is not set +CONFIG_DEBUG_USER=y +# CONFIG_DEBUG_ERRORS is not set +CONFIG_DEBUG_LL=y +# CONFIG_DEBUG_ICEDCC is not set + +# +# Security options +# +# CONFIG_KEYS is not set +# CONFIG_SECURITY is not set +# CONFIG_SECURITY_FILE_CAPABILITIES is not set +CONFIG_CRYPTO=y +CONFIG_CRYPTO_ALGAPI=y +CONFIG_CRYPTO_BLKCIPHER=y +CONFIG_CRYPTO_MANAGER=y +# CONFIG_CRYPTO_HMAC is not set +# CONFIG_CRYPTO_XCBC is not set +# CONFIG_CRYPTO_NULL is not set +# CONFIG_CRYPTO_MD4 is not set +CONFIG_CRYPTO_MD5=y +# CONFIG_CRYPTO_SHA1 is not set +# CONFIG_CRYPTO_SHA256 is not set +# CONFIG_CRYPTO_SHA512 is not set +# CONFIG_CRYPTO_WP512 is not set +# CONFIG_CRYPTO_TGR192 is not set +# CONFIG_CRYPTO_GF128MUL is not set +# CONFIG_CRYPTO_ECB is not set +CONFIG_CRYPTO_CBC=y +# CONFIG_CRYPTO_PCBC is not set +# CONFIG_CRYPTO_LRW is not set +# CONFIG_CRYPTO_XTS is not set +# CONFIG_CRYPTO_CRYPTD is not set +CONFIG_CRYPTO_DES=y +# CONFIG_CRYPTO_FCRYPT is not set +# CONFIG_CRYPTO_BLOWFISH is not set +# CONFIG_CRYPTO_TWOFISH is not set +# CONFIG_CRYPTO_SERPENT is not set +# CONFIG_CRYPTO_AES is not set +# CONFIG_CRYPTO_CAST5 is not set +# CONFIG_CRYPTO_CAST6 is not set +# CONFIG_CRYPTO_TEA is not set +# CONFIG_CRYPTO_ARC4 is not set +# CONFIG_CRYPTO_KHAZAD is not set +# CONFIG_CRYPTO_ANUBIS is not set +# CONFIG_CRYPTO_SEED is not set +# CONFIG_CRYPTO_DEFLATE is not set +# CONFIG_CRYPTO_MICHAEL_MIC is not set +# CONFIG_CRYPTO_CRC32C is not set +# CONFIG_CRYPTO_CAMELLIA is not set +# CONFIG_CRYPTO_TEST is not set +# CONFIG_CRYPTO_AUTHENC is not set +# CONFIG_CRYPTO_HW is not set + +# +# Library routines +# +CONFIG_BITREVERSE=y +# CONFIG_CRC_CCITT is not set +# CONFIG_CRC16 is not set +# CONFIG_CRC_ITU_T is not set +CONFIG_CRC32=y +# CONFIG_CRC7 is not set +# CONFIG_LIBCRC32C is not set +CONFIG_ZLIB_INFLATE=y +CONFIG_ZLIB_DEFLATE=y +CONFIG_PLIST=y +CONFIG_HAS_IOMEM=y +CONFIG_HAS_IOPORT=y +CONFIG_HAS_DMA=y diff --git a/arch/arm/configs/usb-a9263_defconfig b/arch/arm/configs/usb-a9263_defconfig new file mode 100644 index 00000000000..48d455bc736 --- /dev/null +++ b/arch/arm/configs/usb-a9263_defconfig @@ -0,0 +1,1134 @@ +# +# Automatically generated make config: don't edit +# Linux kernel version: 2.6.24 +# Tue Apr 15 11:15:19 2008 +# +CONFIG_ARM=y +CONFIG_SYS_SUPPORTS_APM_EMULATION=y +CONFIG_GENERIC_GPIO=y +CONFIG_GENERIC_TIME=y +CONFIG_GENERIC_CLOCKEVENTS=y +CONFIG_MMU=y +# CONFIG_NO_IOPORT is not set +CONFIG_GENERIC_HARDIRQS=y +CONFIG_STACKTRACE_SUPPORT=y +CONFIG_LOCKDEP_SUPPORT=y +CONFIG_TRACE_IRQFLAGS_SUPPORT=y +CONFIG_HARDIRQS_SW_RESEND=y +CONFIG_GENERIC_IRQ_PROBE=y +CONFIG_RWSEM_GENERIC_SPINLOCK=y +# CONFIG_ARCH_HAS_ILOG2_U32 is not set +# CONFIG_ARCH_HAS_ILOG2_U64 is not set +CONFIG_GENERIC_HWEIGHT=y +CONFIG_GENERIC_CALIBRATE_DELAY=y +CONFIG_ZONE_DMA=y +CONFIG_VECTORS_BASE=0xffff0000 +CONFIG_DEFCONFIG_LIST="/lib/modules/$UNAME_RELEASE/.config" + +# +# General setup +# +CONFIG_EXPERIMENTAL=y +CONFIG_BROKEN_ON_SMP=y +CONFIG_INIT_ENV_ARG_LIMIT=32 +CONFIG_LOCALVERSION="" +# CONFIG_LOCALVERSION_AUTO is not set +# CONFIG_SWAP is not set +CONFIG_SYSVIPC=y +CONFIG_SYSVIPC_SYSCTL=y +# CONFIG_POSIX_MQUEUE is not set +# CONFIG_BSD_PROCESS_ACCT is not set +# CONFIG_TASKSTATS is not set +# CONFIG_USER_NS is not set +# CONFIG_PID_NS is not set +# CONFIG_AUDIT is not set +# CONFIG_IKCONFIG is not set +CONFIG_LOG_BUF_SHIFT=14 +# CONFIG_CGROUPS is not set +CONFIG_FAIR_GROUP_SCHED=y +CONFIG_FAIR_USER_SCHED=y +# CONFIG_FAIR_CGROUP_SCHED is not set +# CONFIG_SYSFS_DEPRECATED is not set +# CONFIG_RELAY is not set +# CONFIG_BLK_DEV_INITRD is not set +# CONFIG_CC_OPTIMIZE_FOR_SIZE is not set +CONFIG_SYSCTL=y +# CONFIG_EMBEDDED is not set +CONFIG_UID16=y +CONFIG_SYSCTL_SYSCALL=y +CONFIG_KALLSYMS=y +# CONFIG_KALLSYMS_ALL is not set +# CONFIG_KALLSYMS_EXTRA_PASS is not set +CONFIG_HOTPLUG=y +CONFIG_PRINTK=y +CONFIG_BUG=y +CONFIG_ELF_CORE=y +CONFIG_BASE_FULL=y +CONFIG_FUTEX=y +CONFIG_ANON_INODES=y +CONFIG_EPOLL=y +CONFIG_SIGNALFD=y +CONFIG_EVENTFD=y +CONFIG_SHMEM=y +CONFIG_VM_EVENT_COUNTERS=y +CONFIG_SLAB=y +# CONFIG_SLUB is not set +# CONFIG_SLOB is not set +CONFIG_SLABINFO=y +CONFIG_RT_MUTEXES=y +# CONFIG_TINY_SHMEM is not set +CONFIG_BASE_SMALL=0 +CONFIG_MODULES=y +CONFIG_MODULE_UNLOAD=y +# CONFIG_MODULE_FORCE_UNLOAD is not set +# CONFIG_MODVERSIONS is not set +# CONFIG_MODULE_SRCVERSION_ALL is not set +CONFIG_KMOD=y +CONFIG_BLOCK=y +# CONFIG_LBD is not set +# CONFIG_BLK_DEV_IO_TRACE is not set +# CONFIG_LSF is not set +# CONFIG_BLK_DEV_BSG is not set + +# +# IO Schedulers +# +CONFIG_IOSCHED_NOOP=y +CONFIG_IOSCHED_AS=y +# CONFIG_IOSCHED_DEADLINE is not set +# CONFIG_IOSCHED_CFQ is not set +CONFIG_DEFAULT_AS=y +# CONFIG_DEFAULT_DEADLINE is not set +# CONFIG_DEFAULT_CFQ is not set +# CONFIG_DEFAULT_NOOP is not set +CONFIG_DEFAULT_IOSCHED="anticipatory" + +# +# System Type +# +# CONFIG_ARCH_AAEC2000 is not set +# CONFIG_ARCH_INTEGRATOR is not set +# CONFIG_ARCH_REALVIEW is not set +# CONFIG_ARCH_VERSATILE is not set +CONFIG_ARCH_AT91=y +# CONFIG_ARCH_CLPS7500 is not set +# CONFIG_ARCH_CLPS711X is not set +# CONFIG_ARCH_CO285 is not set +# CONFIG_ARCH_EBSA110 is not set +# CONFIG_ARCH_EP93XX is not set +# CONFIG_ARCH_FOOTBRIDGE is not set +# CONFIG_ARCH_NETX is not set +# CONFIG_ARCH_H720X is not set +# CONFIG_ARCH_IMX is not set +# CONFIG_ARCH_IOP13XX is not set +# CONFIG_ARCH_IOP32X is not set +# CONFIG_ARCH_IOP33X is not set +# CONFIG_ARCH_IXP23XX is not set +# CONFIG_ARCH_IXP2000 is not set +# CONFIG_ARCH_IXP4XX is not set +# CONFIG_ARCH_L7200 is not set +# CONFIG_ARCH_KS8695 is not set +# CONFIG_ARCH_NS9XXX is not set +# CONFIG_ARCH_MXC is not set +# CONFIG_ARCH_PNX4008 is not set +# CONFIG_ARCH_PXA is not set +# CONFIG_ARCH_RPC is not set +# CONFIG_ARCH_SA1100 is not set +# CONFIG_ARCH_S3C2410 is not set +# CONFIG_ARCH_SHARK is not set +# CONFIG_ARCH_LH7A40X is not set +# CONFIG_ARCH_DAVINCI is not set +# CONFIG_ARCH_OMAP is not set + +# +# Boot options +# + +# +# Power management +# + +# +# Atmel AT91 System-on-Chip +# +# CONFIG_ARCH_AT91RM9200 is not set +# CONFIG_ARCH_AT91SAM9260 is not set +# CONFIG_ARCH_AT91SAM9261 is not set +CONFIG_ARCH_AT91SAM9263=y +# CONFIG_ARCH_AT91SAM9RL is not set +# CONFIG_ARCH_AT91CAP9 is not set +# CONFIG_ARCH_AT91X40 is not set +CONFIG_AT91_PMC_UNIT=y + +# +# AT91SAM9263 Board Type +# +# CONFIG_MACH_AT91SAM9263EK is not set +CONFIG_MACH_USB_A9263=y + +# +# AT91 Board Options +# + +# +# AT91 Feature Selections +# +# CONFIG_AT91_PROGRAMMABLE_CLOCKS is not set +CONFIG_AT91_SLOW_CLOCK=y +CONFIG_AT91_TIMER_HZ=100 +CONFIG_AT91_EARLY_DBGU=y +# CONFIG_AT91_EARLY_USART0 is not set +# CONFIG_AT91_EARLY_USART1 is not set +# CONFIG_AT91_EARLY_USART2 is not set +# CONFIG_AT91_EARLY_USART3 is not set +# CONFIG_AT91_EARLY_USART4 is not set +# CONFIG_AT91_EARLY_USART5 is not set + +# +# Processor Type +# +CONFIG_CPU_32=y +CONFIG_CPU_ARM926T=y +CONFIG_CPU_32v5=y +CONFIG_CPU_ABRT_EV5TJ=y +CONFIG_CPU_CACHE_VIVT=y +CONFIG_CPU_COPY_V4WB=y +CONFIG_CPU_TLB_V4WBI=y +CONFIG_CPU_CP15=y +CONFIG_CPU_CP15_MMU=y + +# +# Processor Features +# +# CONFIG_ARM_THUMB is not set +# CONFIG_CPU_ICACHE_DISABLE is not set +# CONFIG_CPU_DCACHE_DISABLE is not set +# CONFIG_CPU_DCACHE_WRITETHROUGH is not set +# CONFIG_CPU_CACHE_ROUND_ROBIN is not set +# CONFIG_OUTER_CACHE is not set + +# +# Bus support +# +# CONFIG_PCI_SYSCALL is not set +# CONFIG_ARCH_SUPPORTS_MSI is not set +# CONFIG_PCCARD is not set + +# +# Kernel Features +# +# CONFIG_TICK_ONESHOT is not set +# CONFIG_NO_HZ is not set +# CONFIG_HIGH_RES_TIMERS is not set +CONFIG_GENERIC_CLOCKEVENTS_BUILD=y +# CONFIG_PREEMPT is not set +CONFIG_HZ=100 +CONFIG_AEABI=y +CONFIG_OABI_COMPAT=y +# CONFIG_ARCH_DISCONTIGMEM_ENABLE is not set +CONFIG_SELECT_MEMORY_MODEL=y +CONFIG_FLATMEM_MANUAL=y +# CONFIG_DISCONTIGMEM_MANUAL is not set +# CONFIG_SPARSEMEM_MANUAL is not set +CONFIG_FLATMEM=y +CONFIG_FLAT_NODE_MEM_MAP=y +# CONFIG_SPARSEMEM_STATIC is not set +# CONFIG_SPARSEMEM_VMEMMAP_ENABLE is not set +CONFIG_SPLIT_PTLOCK_CPUS=4096 +# CONFIG_RESOURCES_64BIT is not set +CONFIG_ZONE_DMA_FLAG=1 +CONFIG_BOUNCE=y +CONFIG_VIRT_TO_BUS=y +# CONFIG_LEDS is not set +CONFIG_ALIGNMENT_TRAP=y + +# +# Boot options +# +CONFIG_ZBOOT_ROM_TEXT=0x0 +CONFIG_ZBOOT_ROM_BSS=0x0 +CONFIG_CMDLINE="mem=64M console=ttyS0,115200" +# CONFIG_XIP_KERNEL is not set +# CONFIG_KEXEC is not set + +# +# Floating point emulation +# + +# +# At least one emulation must be selected +# +CONFIG_FPE_NWFPE=y +# CONFIG_FPE_NWFPE_XP is not set +# CONFIG_FPE_FASTFPE is not set +# CONFIG_VFP is not set + +# +# Userspace binary formats +# +CONFIG_BINFMT_ELF=y +# CONFIG_BINFMT_AOUT is not set +# CONFIG_BINFMT_MISC is not set + +# +# Power management options +# +CONFIG_PM=y +# CONFIG_PM_LEGACY is not set +# CONFIG_PM_DEBUG is not set +CONFIG_PM_SLEEP=y +CONFIG_SUSPEND_UP_POSSIBLE=y +CONFIG_SUSPEND=y +# CONFIG_APM_EMULATION is not set + +# +# Networking +# +CONFIG_NET=y + +# +# Networking options +# +CONFIG_PACKET=y +# CONFIG_PACKET_MMAP is not set +CONFIG_UNIX=y +# CONFIG_NET_KEY is not set +CONFIG_INET=y +CONFIG_IP_MULTICAST=y +CONFIG_IP_ADVANCED_ROUTER=y +CONFIG_ASK_IP_FIB_HASH=y +# CONFIG_IP_FIB_TRIE is not set +CONFIG_IP_FIB_HASH=y +# CONFIG_IP_MULTIPLE_TABLES is not set +# CONFIG_IP_ROUTE_MULTIPATH is not set +CONFIG_IP_ROUTE_VERBOSE=y +CONFIG_IP_PNP=y +# CONFIG_IP_PNP_DHCP is not set +CONFIG_IP_PNP_BOOTP=y +CONFIG_IP_PNP_RARP=y +# CONFIG_NET_IPIP is not set +# CONFIG_NET_IPGRE is not set +CONFIG_IP_MROUTE=y +CONFIG_IP_PIMSM_V1=y +CONFIG_IP_PIMSM_V2=y +# CONFIG_ARPD is not set +# CONFIG_SYN_COOKIES is not set +# CONFIG_INET_AH is not set +# CONFIG_INET_ESP is not set +# CONFIG_INET_IPCOMP is not set +# CONFIG_INET_XFRM_TUNNEL is not set +# CONFIG_INET_TUNNEL is not set +# CONFIG_INET_XFRM_MODE_TRANSPORT is not set +# CONFIG_INET_XFRM_MODE_TUNNEL is not set +# CONFIG_INET_XFRM_MODE_BEET is not set +# CONFIG_INET_LRO is not set +# CONFIG_INET_DIAG is not set +# CONFIG_TCP_CONG_ADVANCED is not set +CONFIG_TCP_CONG_CUBIC=y +CONFIG_DEFAULT_TCP_CONG="cubic" +# CONFIG_TCP_MD5SIG is not set +# CONFIG_IPV6 is not set +# CONFIG_INET6_XFRM_TUNNEL is not set +# CONFIG_INET6_TUNNEL is not set +# CONFIG_NETWORK_SECMARK is not set +# CONFIG_NETFILTER is not set +# CONFIG_IP_DCCP is not set +# CONFIG_IP_SCTP is not set +# CONFIG_TIPC is not set +# CONFIG_ATM is not set +# CONFIG_BRIDGE is not set +# CONFIG_VLAN_8021Q is not set +# CONFIG_DECNET is not set +# CONFIG_LLC2 is not set +# CONFIG_IPX is not set +# CONFIG_ATALK is not set +# CONFIG_X25 is not set +# CONFIG_LAPB is not set +# CONFIG_ECONET is not set +# CONFIG_WAN_ROUTER is not set +# CONFIG_NET_SCHED is not set + +# +# Network testing +# +# CONFIG_NET_PKTGEN is not set +# CONFIG_HAMRADIO is not set +# CONFIG_IRDA is not set +# CONFIG_BT is not set +# CONFIG_AF_RXRPC is not set + +# +# Wireless +# +# CONFIG_CFG80211 is not set +# CONFIG_WIRELESS_EXT is not set +# CONFIG_MAC80211 is not set +# CONFIG_IEEE80211 is not set +# CONFIG_RFKILL is not set +# CONFIG_NET_9P is not set + +# +# Device Drivers +# + +# +# Generic Driver Options +# +CONFIG_UEVENT_HELPER_PATH="/sbin/hotplug" +CONFIG_STANDALONE=y +CONFIG_PREVENT_FIRMWARE_BUILD=y +# CONFIG_FW_LOADER is not set +# CONFIG_DEBUG_DRIVER is not set +# CONFIG_DEBUG_DEVRES is not set +# CONFIG_SYS_HYPERVISOR is not set +# CONFIG_CONNECTOR is not set +CONFIG_MTD=y +# CONFIG_MTD_DEBUG is not set +# CONFIG_MTD_CONCAT is not set +CONFIG_MTD_PARTITIONS=y +# CONFIG_MTD_REDBOOT_PARTS is not set +CONFIG_MTD_CMDLINE_PARTS=y +# CONFIG_MTD_AFS_PARTS is not set + +# +# User Modules And Translation Layers +# +CONFIG_MTD_CHAR=y +CONFIG_MTD_BLKDEVS=y +CONFIG_MTD_BLOCK=y +# CONFIG_FTL is not set +# CONFIG_NFTL is not set +# CONFIG_INFTL is not set +# CONFIG_RFD_FTL is not set +# CONFIG_SSFDC is not set +# CONFIG_MTD_OOPS is not set + +# +# RAM/ROM/Flash chip drivers +# +# CONFIG_MTD_CFI is not set +# CONFIG_MTD_JEDECPROBE is not set +CONFIG_MTD_MAP_BANK_WIDTH_1=y +CONFIG_MTD_MAP_BANK_WIDTH_2=y +CONFIG_MTD_MAP_BANK_WIDTH_4=y +# CONFIG_MTD_MAP_BANK_WIDTH_8 is not set +# CONFIG_MTD_MAP_BANK_WIDTH_16 is not set +# CONFIG_MTD_MAP_BANK_WIDTH_32 is not set +CONFIG_MTD_CFI_I1=y +CONFIG_MTD_CFI_I2=y +# CONFIG_MTD_CFI_I4 is not set +# CONFIG_MTD_CFI_I8 is not set +# CONFIG_MTD_RAM is not set +# CONFIG_MTD_ROM is not set +# CONFIG_MTD_ABSENT is not set + +# +# Mapping drivers for chip access +# +# CONFIG_MTD_COMPLEX_MAPPINGS is not set +# CONFIG_MTD_PLATRAM is not set + +# +# Self-contained MTD device drivers +# +CONFIG_MTD_DATAFLASH=y +# CONFIG_MTD_M25P80 is not set +# CONFIG_MTD_SLRAM is not set +# CONFIG_MTD_PHRAM is not set +# CONFIG_MTD_MTDRAM is not set +# CONFIG_MTD_BLOCK2MTD is not set + +# +# Disk-On-Chip Device Drivers +# +# CONFIG_MTD_DOC2000 is not set +# CONFIG_MTD_DOC2001 is not set +# CONFIG_MTD_DOC2001PLUS is not set +CONFIG_MTD_NAND=y +# CONFIG_MTD_NAND_VERIFY_WRITE is not set +# CONFIG_MTD_NAND_ECC_SMC is not set +# CONFIG_MTD_NAND_MUSEUM_IDS is not set +CONFIG_MTD_NAND_IDS=y +# CONFIG_MTD_NAND_DISKONCHIP is not set +CONFIG_MTD_NAND_AT91=y +CONFIG_MTD_NAND_AT91_ECC_SOFT=y +# CONFIG_MTD_NAND_AT91_ECC_HW is not set +# CONFIG_MTD_NAND_AT91_ECC_NONE is not set +# CONFIG_MTD_NAND_NANDSIM is not set +# CONFIG_MTD_NAND_PLATFORM is not set +# CONFIG_MTD_ALAUDA is not set +# CONFIG_MTD_ONENAND is not set + +# +# UBI - Unsorted block images +# +# CONFIG_MTD_UBI is not set +# CONFIG_PARPORT is not set +CONFIG_BLK_DEV=y +# CONFIG_BLK_DEV_COW_COMMON is not set +CONFIG_BLK_DEV_LOOP=y +# CONFIG_BLK_DEV_CRYPTOLOOP is not set +# CONFIG_BLK_DEV_NBD is not set +# CONFIG_BLK_DEV_UB is not set +# CONFIG_BLK_DEV_RAM is not set +# CONFIG_CDROM_PKTCDVD is not set +# CONFIG_ATA_OVER_ETH is not set +# CONFIG_MISC_DEVICES is not set + +# +# SCSI device support +# +# CONFIG_RAID_ATTRS is not set +CONFIG_SCSI=y +CONFIG_SCSI_DMA=y +# CONFIG_SCSI_TGT is not set +# CONFIG_SCSI_NETLINK is not set +CONFIG_SCSI_PROC_FS=y + +# +# SCSI support type (disk, tape, CD-ROM) +# +CONFIG_BLK_DEV_SD=y +# CONFIG_CHR_DEV_ST is not set +# CONFIG_CHR_DEV_OSST is not set +# CONFIG_BLK_DEV_SR is not set +# CONFIG_CHR_DEV_SG is not set +# CONFIG_CHR_DEV_SCH is not set + +# +# Some SCSI devices (e.g. CD jukebox) support multiple LUNs +# +CONFIG_SCSI_MULTI_LUN=y +# CONFIG_SCSI_CONSTANTS is not set +# CONFIG_SCSI_LOGGING is not set +# CONFIG_SCSI_SCAN_ASYNC is not set +CONFIG_SCSI_WAIT_SCAN=m + +# +# SCSI Transports +# +# CONFIG_SCSI_SPI_ATTRS is not set +# CONFIG_SCSI_FC_ATTRS is not set +# CONFIG_SCSI_ISCSI_ATTRS is not set +# CONFIG_SCSI_SAS_LIBSAS is not set +# CONFIG_SCSI_SRP_ATTRS is not set +CONFIG_SCSI_LOWLEVEL=y +# CONFIG_ISCSI_TCP is not set +# CONFIG_SCSI_DEBUG is not set +# CONFIG_ATA is not set +# CONFIG_MD is not set +CONFIG_NETDEVICES=y +# CONFIG_NETDEVICES_MULTIQUEUE is not set +# CONFIG_DUMMY is not set +# CONFIG_BONDING is not set +# CONFIG_MACVLAN is not set +# CONFIG_EQUALIZER is not set +# CONFIG_TUN is not set +# CONFIG_VETH is not set +CONFIG_PHYLIB=y + +# +# MII PHY device drivers +# +# CONFIG_MARVELL_PHY is not set +# CONFIG_DAVICOM_PHY is not set +# CONFIG_QSEMI_PHY is not set +# CONFIG_LXT_PHY is not set +# CONFIG_CICADA_PHY is not set +# CONFIG_VITESSE_PHY is not set +# CONFIG_SMSC_PHY is not set +# CONFIG_BROADCOM_PHY is not set +# CONFIG_ICPLUS_PHY is not set +# CONFIG_FIXED_PHY is not set +# CONFIG_MDIO_BITBANG is not set +CONFIG_NET_ETHERNET=y +CONFIG_MII=y +CONFIG_MACB=y +# CONFIG_AX88796 is not set +# CONFIG_SMC91X is not set +# CONFIG_DM9000 is not set +# CONFIG_IBM_NEW_EMAC_ZMII is not set +# CONFIG_IBM_NEW_EMAC_RGMII is not set +# CONFIG_IBM_NEW_EMAC_TAH is not set +# CONFIG_IBM_NEW_EMAC_EMAC4 is not set +# CONFIG_B44 is not set +CONFIG_NETDEV_1000=y +CONFIG_NETDEV_10000=y + +# +# Wireless LAN +# +# CONFIG_WLAN_PRE80211 is not set +# CONFIG_WLAN_80211 is not set + +# +# USB Network Adapters +# +# CONFIG_USB_CATC is not set +# CONFIG_USB_KAWETH is not set +# CONFIG_USB_PEGASUS is not set +# CONFIG_USB_RTL8150 is not set +# CONFIG_USB_USBNET is not set +# CONFIG_WAN is not set +# CONFIG_PPP is not set +# CONFIG_SLIP is not set +# CONFIG_SHAPER is not set +# CONFIG_NETCONSOLE is not set +# CONFIG_NETPOLL is not set +# CONFIG_NET_POLL_CONTROLLER is not set +# CONFIG_ISDN is not set + +# +# Input device support +# +CONFIG_INPUT=y +# CONFIG_INPUT_FF_MEMLESS is not set +# CONFIG_INPUT_POLLDEV is not set + +# +# Userland interfaces +# +CONFIG_INPUT_MOUSEDEV=y +# CONFIG_INPUT_MOUSEDEV_PSAUX is not set +CONFIG_INPUT_MOUSEDEV_SCREEN_X=1024 +CONFIG_INPUT_MOUSEDEV_SCREEN_Y=768 +# CONFIG_INPUT_JOYDEV is not set +CONFIG_INPUT_EVDEV=y +CONFIG_INPUT_EVBUG=y + +# +# Input Device Drivers +# +CONFIG_INPUT_KEYBOARD=y +# CONFIG_KEYBOARD_ATKBD is not set +# CONFIG_KEYBOARD_SUNKBD is not set +# CONFIG_KEYBOARD_LKKBD is not set +# CONFIG_KEYBOARD_XTKBD is not set +# CONFIG_KEYBOARD_NEWTON is not set +# CONFIG_KEYBOARD_STOWAWAY is not set +CONFIG_KEYBOARD_GPIO=y +# CONFIG_INPUT_MOUSE is not set +# CONFIG_INPUT_JOYSTICK is not set +# CONFIG_INPUT_TABLET is not set +# CONFIG_INPUT_TOUCHSCREEN is not set +# CONFIG_INPUT_MISC is not set + +# +# Hardware I/O ports +# +# CONFIG_SERIO is not set +# CONFIG_GAMEPORT is not set + +# +# Character devices +# +CONFIG_VT=y +CONFIG_VT_CONSOLE=y +CONFIG_HW_CONSOLE=y +# CONFIG_VT_HW_CONSOLE_BINDING is not set +# CONFIG_SERIAL_NONSTANDARD is not set + +# +# Serial drivers +# +# CONFIG_SERIAL_8250 is not set + +# +# Non-8250 serial port support +# +CONFIG_SERIAL_ATMEL=y +CONFIG_SERIAL_ATMEL_CONSOLE=y +# CONFIG_SERIAL_ATMEL_TTYAT is not set +CONFIG_SERIAL_CORE=y +CONFIG_SERIAL_CORE_CONSOLE=y +CONFIG_UNIX98_PTYS=y +CONFIG_LEGACY_PTYS=y +CONFIG_LEGACY_PTY_COUNT=256 +# CONFIG_IPMI_HANDLER is not set +CONFIG_HW_RANDOM=y +# CONFIG_NVRAM is not set +# CONFIG_R3964 is not set +# CONFIG_RAW_DRIVER is not set +# CONFIG_TCG_TPM is not set +# CONFIG_I2C is not set + +# +# SPI support +# +CONFIG_SPI=y +# CONFIG_SPI_DEBUG is not set +CONFIG_SPI_MASTER=y + +# +# SPI Master Controller Drivers +# +CONFIG_SPI_ATMEL=y +# CONFIG_SPI_BITBANG is not set + +# +# SPI Protocol Masters +# +# CONFIG_SPI_AT25 is not set +# CONFIG_SPI_SPIDEV is not set +# CONFIG_SPI_TLE62X0 is not set +# CONFIG_W1 is not set +# CONFIG_POWER_SUPPLY is not set +# CONFIG_HWMON is not set +# CONFIG_WATCHDOG is not set + +# +# Sonics Silicon Backplane +# +CONFIG_SSB_POSSIBLE=y +# CONFIG_SSB is not set + +# +# Multifunction device drivers +# +# CONFIG_MFD_SM501 is not set + +# +# Multimedia devices +# +# CONFIG_VIDEO_DEV is not set +# CONFIG_DVB_CORE is not set +# CONFIG_DAB is not set + +# +# Graphics support +# +# CONFIG_VGASTATE is not set +# CONFIG_VIDEO_OUTPUT_CONTROL is not set +# CONFIG_FB is not set +# CONFIG_BACKLIGHT_LCD_SUPPORT is not set + +# +# Display device support +# +# CONFIG_DISPLAY_SUPPORT is not set + +# +# Console display driver support +# +# CONFIG_VGA_CONSOLE is not set +CONFIG_DUMMY_CONSOLE=y + +# +# Sound +# +# CONFIG_SOUND is not set +CONFIG_HID_SUPPORT=y +CONFIG_HID=y +# CONFIG_HID_DEBUG is not set +# CONFIG_HIDRAW is not set + +# +# USB Input Devices +# +# CONFIG_USB_HID is not set + +# +# USB HID Boot Protocol drivers +# +# CONFIG_USB_KBD is not set +# CONFIG_USB_MOUSE is not set +CONFIG_USB_SUPPORT=y +CONFIG_USB_ARCH_HAS_HCD=y +CONFIG_USB_ARCH_HAS_OHCI=y +# CONFIG_USB_ARCH_HAS_EHCI is not set +CONFIG_USB=y +# CONFIG_USB_DEBUG is not set + +# +# Miscellaneous USB options +# +CONFIG_USB_DEVICEFS=y +CONFIG_USB_DEVICE_CLASS=y +# CONFIG_USB_DYNAMIC_MINORS is not set +# CONFIG_USB_SUSPEND is not set +# CONFIG_USB_PERSIST is not set +# CONFIG_USB_OTG is not set + +# +# USB Host Controller Drivers +# +# CONFIG_USB_ISP116X_HCD is not set +CONFIG_USB_OHCI_HCD=y +# CONFIG_USB_OHCI_BIG_ENDIAN_DESC is not set +# CONFIG_USB_OHCI_BIG_ENDIAN_MMIO is not set +CONFIG_USB_OHCI_LITTLE_ENDIAN=y +# CONFIG_USB_SL811_HCD is not set +# CONFIG_USB_R8A66597_HCD is not set + +# +# USB Device Class drivers +# +# CONFIG_USB_ACM is not set +# CONFIG_USB_PRINTER is not set + +# +# NOTE: USB_STORAGE enables SCSI, and 'SCSI disk support' +# + +# +# may also be needed; see USB_STORAGE Help for more information +# +CONFIG_USB_STORAGE=y +# CONFIG_USB_STORAGE_DEBUG is not set +# CONFIG_USB_STORAGE_DATAFAB is not set +# CONFIG_USB_STORAGE_FREECOM is not set +# CONFIG_USB_STORAGE_ISD200 is not set +# CONFIG_USB_STORAGE_DPCM is not set +# CONFIG_USB_STORAGE_USBAT is not set +# CONFIG_USB_STORAGE_SDDR09 is not set +# CONFIG_USB_STORAGE_SDDR55 is not set +# CONFIG_USB_STORAGE_JUMPSHOT is not set +# CONFIG_USB_STORAGE_ALAUDA is not set +# CONFIG_USB_STORAGE_KARMA is not set +# CONFIG_USB_LIBUSUAL is not set + +# +# USB Imaging devices +# +# CONFIG_USB_MDC800 is not set +# CONFIG_USB_MICROTEK is not set +CONFIG_USB_MON=y + +# +# USB port drivers +# + +# +# USB Serial Converter support +# +# CONFIG_USB_SERIAL is not set + +# +# USB Miscellaneous drivers +# +# CONFIG_USB_EMI62 is not set +# CONFIG_USB_EMI26 is not set +# CONFIG_USB_ADUTUX is not set +# CONFIG_USB_AUERSWALD is not set +# CONFIG_USB_RIO500 is not set +# CONFIG_USB_LEGOTOWER is not set +# CONFIG_USB_LCD is not set +# CONFIG_USB_BERRY_CHARGE is not set +# CONFIG_USB_LED is not set +# CONFIG_USB_CYPRESS_CY7C63 is not set +# CONFIG_USB_CYTHERM is not set +# CONFIG_USB_PHIDGET is not set +# CONFIG_USB_IDMOUSE is not set +# CONFIG_USB_FTDI_ELAN is not set +# CONFIG_USB_APPLEDISPLAY is not set +# CONFIG_USB_LD is not set +# CONFIG_USB_TRANCEVIBRATOR is not set +# CONFIG_USB_IOWARRIOR is not set +# CONFIG_USB_TEST is not set + +# +# USB DSL modem support +# + +# +# USB Gadget Support +# +CONFIG_USB_GADGET=y +# CONFIG_USB_GADGET_DEBUG is not set +# CONFIG_USB_GADGET_DEBUG_FILES is not set +CONFIG_USB_GADGET_SELECTED=y +# CONFIG_USB_GADGET_AMD5536UDC is not set +# CONFIG_USB_GADGET_ATMEL_USBA is not set +# CONFIG_USB_GADGET_FSL_USB2 is not set +# CONFIG_USB_GADGET_NET2280 is not set +# CONFIG_USB_GADGET_PXA2XX is not set +# CONFIG_USB_GADGET_M66592 is not set +# CONFIG_USB_GADGET_GOKU is not set +# CONFIG_USB_GADGET_LH7A40X is not set +# CONFIG_USB_GADGET_OMAP is not set +# CONFIG_USB_GADGET_S3C2410 is not set +CONFIG_USB_GADGET_AT91=y +CONFIG_USB_AT91=y +# CONFIG_USB_GADGET_DUMMY_HCD is not set +# CONFIG_USB_GADGET_DUALSPEED is not set +# CONFIG_USB_ZERO is not set +CONFIG_USB_ETH=y +CONFIG_USB_ETH_RNDIS=y +# CONFIG_USB_GADGETFS is not set +# CONFIG_USB_FILE_STORAGE is not set +# CONFIG_USB_G_SERIAL is not set +# CONFIG_USB_MIDI_GADGET is not set +# CONFIG_MMC is not set +CONFIG_NEW_LEDS=y +CONFIG_LEDS_CLASS=y + +# +# LED drivers +# +CONFIG_LEDS_GPIO=y + +# +# LED Triggers +# +CONFIG_LEDS_TRIGGERS=y +# CONFIG_LEDS_TRIGGER_TIMER is not set +CONFIG_LEDS_TRIGGER_HEARTBEAT=y +CONFIG_RTC_LIB=y +# CONFIG_RTC_CLASS is not set + +# +# File systems +# +CONFIG_EXT2_FS=y +# CONFIG_EXT2_FS_XATTR is not set +# CONFIG_EXT2_FS_XIP is not set +# CONFIG_EXT3_FS is not set +# CONFIG_EXT4DEV_FS is not set +# CONFIG_REISERFS_FS is not set +# CONFIG_JFS_FS is not set +CONFIG_FS_POSIX_ACL=y +# CONFIG_XFS_FS is not set +# CONFIG_GFS2_FS is not set +# CONFIG_OCFS2_FS is not set +# CONFIG_MINIX_FS is not set +# CONFIG_ROMFS_FS is not set +CONFIG_INOTIFY=y +CONFIG_INOTIFY_USER=y +# CONFIG_QUOTA is not set +CONFIG_DNOTIFY=y +# CONFIG_AUTOFS_FS is not set +# CONFIG_AUTOFS4_FS is not set +CONFIG_FUSE_FS=m + +# +# CD-ROM/DVD Filesystems +# +# CONFIG_ISO9660_FS is not set +# CONFIG_UDF_FS is not set + +# +# DOS/FAT/NT Filesystems +# +CONFIG_FAT_FS=y +# CONFIG_MSDOS_FS is not set +CONFIG_VFAT_FS=y +CONFIG_FAT_DEFAULT_CODEPAGE=437 +CONFIG_FAT_DEFAULT_IOCHARSET="iso8859-1" +# CONFIG_NTFS_FS is not set + +# +# Pseudo filesystems +# +CONFIG_PROC_FS=y +CONFIG_PROC_SYSCTL=y +CONFIG_SYSFS=y +CONFIG_TMPFS=y +# CONFIG_TMPFS_POSIX_ACL is not set +# CONFIG_HUGETLB_PAGE is not set +# CONFIG_CONFIGFS_FS is not set + +# +# Miscellaneous filesystems +# +# CONFIG_ADFS_FS is not set +# CONFIG_AFFS_FS is not set +# CONFIG_HFS_FS is not set +# CONFIG_HFSPLUS_FS is not set +# CONFIG_BEFS_FS is not set +# CONFIG_BFS_FS is not set +# CONFIG_EFS_FS is not set +CONFIG_JFFS2_FS=y +CONFIG_JFFS2_FS_DEBUG=0 +CONFIG_JFFS2_FS_WRITEBUFFER=y +# CONFIG_JFFS2_FS_WBUF_VERIFY is not set +# CONFIG_JFFS2_SUMMARY is not set +# CONFIG_JFFS2_FS_XATTR is not set +# CONFIG_JFFS2_COMPRESSION_OPTIONS is not set +CONFIG_JFFS2_ZLIB=y +# CONFIG_JFFS2_LZO is not set +CONFIG_JFFS2_RTIME=y +# CONFIG_JFFS2_RUBIN is not set +# CONFIG_CRAMFS is not set +# CONFIG_VXFS_FS is not set +# CONFIG_HPFS_FS is not set +# CONFIG_QNX4FS_FS is not set +# CONFIG_SYSV_FS is not set +# CONFIG_UFS_FS is not set +CONFIG_NETWORK_FILESYSTEMS=y +CONFIG_NFS_FS=y +CONFIG_NFS_V3=y +CONFIG_NFS_V3_ACL=y +CONFIG_NFS_V4=y +# CONFIG_NFS_DIRECTIO is not set +# CONFIG_NFSD is not set +CONFIG_ROOT_NFS=y +CONFIG_LOCKD=y +CONFIG_LOCKD_V4=y +CONFIG_NFS_ACL_SUPPORT=y +CONFIG_NFS_COMMON=y +CONFIG_SUNRPC=y +CONFIG_SUNRPC_GSS=y +# CONFIG_SUNRPC_BIND34 is not set +CONFIG_RPCSEC_GSS_KRB5=y +# CONFIG_RPCSEC_GSS_SPKM3 is not set +# CONFIG_SMB_FS is not set +# CONFIG_CIFS is not set +# CONFIG_NCP_FS is not set +# CONFIG_CODA_FS is not set +# CONFIG_AFS_FS is not set + +# +# Partition Types +# +# CONFIG_PARTITION_ADVANCED is not set +CONFIG_MSDOS_PARTITION=y +CONFIG_NLS=y +CONFIG_NLS_DEFAULT="iso8859-1" +CONFIG_NLS_CODEPAGE_437=y +# CONFIG_NLS_CODEPAGE_737 is not set +# CONFIG_NLS_CODEPAGE_775 is not set +CONFIG_NLS_CODEPAGE_850=y +# CONFIG_NLS_CODEPAGE_852 is not set +# CONFIG_NLS_CODEPAGE_855 is not set +# CONFIG_NLS_CODEPAGE_857 is not set +# CONFIG_NLS_CODEPAGE_860 is not set +# CONFIG_NLS_CODEPAGE_861 is not set +# CONFIG_NLS_CODEPAGE_862 is not set +# CONFIG_NLS_CODEPAGE_863 is not set +# CONFIG_NLS_CODEPAGE_864 is not set +# CONFIG_NLS_CODEPAGE_865 is not set +# CONFIG_NLS_CODEPAGE_866 is not set +# CONFIG_NLS_CODEPAGE_869 is not set +# CONFIG_NLS_CODEPAGE_936 is not set +# CONFIG_NLS_CODEPAGE_950 is not set +# CONFIG_NLS_CODEPAGE_932 is not set +# CONFIG_NLS_CODEPAGE_949 is not set +# CONFIG_NLS_CODEPAGE_874 is not set +# CONFIG_NLS_ISO8859_8 is not set +# CONFIG_NLS_CODEPAGE_1250 is not set +# CONFIG_NLS_CODEPAGE_1251 is not set +# CONFIG_NLS_ASCII is not set +CONFIG_NLS_ISO8859_1=y +# CONFIG_NLS_ISO8859_2 is not set +# CONFIG_NLS_ISO8859_3 is not set +# CONFIG_NLS_ISO8859_4 is not set +# CONFIG_NLS_ISO8859_5 is not set +# CONFIG_NLS_ISO8859_6 is not set +# CONFIG_NLS_ISO8859_7 is not set +# CONFIG_NLS_ISO8859_9 is not set +# CONFIG_NLS_ISO8859_13 is not set +# CONFIG_NLS_ISO8859_14 is not set +# CONFIG_NLS_ISO8859_15 is not set +# CONFIG_NLS_KOI8_R is not set +# CONFIG_NLS_KOI8_U is not set +# CONFIG_NLS_UTF8 is not set +# CONFIG_DLM is not set +# CONFIG_INSTRUMENTATION is not set + +# +# Kernel hacking +# +# CONFIG_PRINTK_TIME is not set +CONFIG_ENABLE_WARN_DEPRECATED=y +CONFIG_ENABLE_MUST_CHECK=y +# CONFIG_MAGIC_SYSRQ is not set +# CONFIG_UNUSED_SYMBOLS is not set +# CONFIG_DEBUG_FS is not set +# CONFIG_HEADERS_CHECK is not set +CONFIG_DEBUG_KERNEL=y +# CONFIG_DEBUG_SHIRQ is not set +CONFIG_DETECT_SOFTLOCKUP=y +CONFIG_SCHED_DEBUG=y +# CONFIG_SCHEDSTATS is not set +# CONFIG_TIMER_STATS is not set +# CONFIG_DEBUG_SLAB is not set +# CONFIG_DEBUG_RT_MUTEXES is not set +# CONFIG_RT_MUTEX_TESTER is not set +# CONFIG_DEBUG_SPINLOCK is not set +# CONFIG_DEBUG_MUTEXES is not set +# CONFIG_DEBUG_LOCK_ALLOC is not set +# CONFIG_PROVE_LOCKING is not set +# CONFIG_LOCK_STAT is not set +# CONFIG_DEBUG_SPINLOCK_SLEEP is not set +# CONFIG_DEBUG_LOCKING_API_SELFTESTS is not set +# CONFIG_DEBUG_KOBJECT is not set +CONFIG_DEBUG_BUGVERBOSE=y +# CONFIG_DEBUG_INFO is not set +# CONFIG_DEBUG_VM is not set +# CONFIG_DEBUG_LIST is not set +# CONFIG_DEBUG_SG is not set +CONFIG_FRAME_POINTER=y +CONFIG_FORCED_INLINING=y +# CONFIG_BOOT_PRINTK_DELAY is not set +# CONFIG_RCU_TORTURE_TEST is not set +# CONFIG_FAULT_INJECTION is not set +# CONFIG_SAMPLES is not set +CONFIG_DEBUG_USER=y +# CONFIG_DEBUG_ERRORS is not set +CONFIG_DEBUG_LL=y +# CONFIG_DEBUG_ICEDCC is not set + +# +# Security options +# +# CONFIG_KEYS is not set +# CONFIG_SECURITY is not set +# CONFIG_SECURITY_FILE_CAPABILITIES is not set +CONFIG_CRYPTO=y +CONFIG_CRYPTO_ALGAPI=y +CONFIG_CRYPTO_BLKCIPHER=y +CONFIG_CRYPTO_MANAGER=y +# CONFIG_CRYPTO_HMAC is not set +# CONFIG_CRYPTO_XCBC is not set +# CONFIG_CRYPTO_NULL is not set +# CONFIG_CRYPTO_MD4 is not set +CONFIG_CRYPTO_MD5=y +# CONFIG_CRYPTO_SHA1 is not set +# CONFIG_CRYPTO_SHA256 is not set +# CONFIG_CRYPTO_SHA512 is not set +# CONFIG_CRYPTO_WP512 is not set +# CONFIG_CRYPTO_TGR192 is not set +# CONFIG_CRYPTO_GF128MUL is not set +# CONFIG_CRYPTO_ECB is not set +CONFIG_CRYPTO_CBC=y +# CONFIG_CRYPTO_PCBC is not set +# CONFIG_CRYPTO_LRW is not set +# CONFIG_CRYPTO_XTS is not set +# CONFIG_CRYPTO_CRYPTD is not set +CONFIG_CRYPTO_DES=y +# CONFIG_CRYPTO_FCRYPT is not set +# CONFIG_CRYPTO_BLOWFISH is not set +# CONFIG_CRYPTO_TWOFISH is not set +# CONFIG_CRYPTO_SERPENT is not set +# CONFIG_CRYPTO_AES is not set +# CONFIG_CRYPTO_CAST5 is not set +# CONFIG_CRYPTO_CAST6 is not set +# CONFIG_CRYPTO_TEA is not set +# CONFIG_CRYPTO_ARC4 is not set +# CONFIG_CRYPTO_KHAZAD is not set +# CONFIG_CRYPTO_ANUBIS is not set +# CONFIG_CRYPTO_SEED is not set +# CONFIG_CRYPTO_DEFLATE is not set +# CONFIG_CRYPTO_MICHAEL_MIC is not set +# CONFIG_CRYPTO_CRC32C is not set +# CONFIG_CRYPTO_CAMELLIA is not set +# CONFIG_CRYPTO_TEST is not set +# CONFIG_CRYPTO_AUTHENC is not set +# CONFIG_CRYPTO_HW is not set + +# +# Library routines +# +CONFIG_BITREVERSE=y +# CONFIG_CRC_CCITT is not set +# CONFIG_CRC16 is not set +# CONFIG_CRC_ITU_T is not set +CONFIG_CRC32=y +# CONFIG_CRC7 is not set +# CONFIG_LIBCRC32C is not set +CONFIG_ZLIB_INFLATE=y +CONFIG_ZLIB_DEFLATE=y +CONFIG_PLIST=y +CONFIG_HAS_IOMEM=y +CONFIG_HAS_IOPORT=y +CONFIG_HAS_DMA=y diff --git a/arch/arm/configs/versatile_defconfig b/arch/arm/configs/versatile_defconfig index 48dca69adda..8355f88f729 100644 --- a/arch/arm/configs/versatile_defconfig +++ b/arch/arm/configs/versatile_defconfig @@ -151,7 +151,6 @@ CONFIG_ARM_AMBA=y # Kernel Features # # CONFIG_PREEMPT is not set -# CONFIG_NO_IDLE_HZ is not set CONFIG_HZ=100 # CONFIG_AEABI is not set # CONFIG_ARCH_DISCONTIGMEM_ENABLE is not set diff --git a/arch/arm/kernel/atags.c b/arch/arm/kernel/atags.c index 64c420805e6..42a1a1415fa 100644 --- a/arch/arm/kernel/atags.c +++ b/arch/arm/kernel/atags.c @@ -1,5 +1,4 @@ #include <linux/slab.h> -#include <linux/kexec.h> #include <linux/proc_fs.h> #include <asm/setup.h> #include <asm/types.h> @@ -7,9 +6,8 @@ struct buffer { size_t size; - char *data; + char data[]; }; -static struct buffer tags_buffer; static int read_buffer(char* page, char** start, off_t off, int count, @@ -29,58 +27,57 @@ read_buffer(char* page, char** start, off_t off, int count, return count; } - -static int -create_proc_entries(void) -{ - struct proc_dir_entry* tags_entry; - - tags_entry = create_proc_read_entry("atags", 0400, NULL, read_buffer, &tags_buffer); - if (!tags_entry) - return -ENOMEM; - - return 0; -} - - -static char __initdata atags_copy_buf[KEXEC_BOOT_PARAMS_SIZE]; -static char __initdata *atags_copy; +#define BOOT_PARAMS_SIZE 1536 +static char __initdata atags_copy[BOOT_PARAMS_SIZE]; void __init save_atags(const struct tag *tags) { - atags_copy = atags_copy_buf; - memcpy(atags_copy, tags, KEXEC_BOOT_PARAMS_SIZE); + memcpy(atags_copy, tags, sizeof(atags_copy)); } - static int __init init_atags_procfs(void) { - struct tag *tag; - int error; + /* + * This cannot go into save_atags() because kmalloc and proc don't work + * yet when it is called. + */ + struct proc_dir_entry *tags_entry; + struct tag *tag = (struct tag *)atags_copy; + struct buffer *b; + size_t size; - if (!atags_copy) { - printk(KERN_WARNING "Exporting ATAGs: No saved tags found\n"); - return -EIO; + if (tag->hdr.tag != ATAG_CORE) { + printk(KERN_INFO "No ATAGs?"); + return -EINVAL; } - for (tag = (struct tag *) atags_copy; tag->hdr.size; tag = tag_next(tag)) + for (; tag->hdr.size; tag = tag_next(tag)) ; - tags_buffer.size = ((char *) tag - atags_copy) + sizeof(tag->hdr); - tags_buffer.data = kmalloc(tags_buffer.size, GFP_KERNEL); - if (tags_buffer.data == NULL) - return -ENOMEM; - memcpy(tags_buffer.data, atags_copy, tags_buffer.size); - - error = create_proc_entries(); - if (error) { - printk(KERN_ERR "Exporting ATAGs: not enough memory\n"); - kfree(tags_buffer.data); - tags_buffer.size = 0; - tags_buffer.data = NULL; - } + /* include the terminating ATAG_NONE */ + size = (char *)tag - atags_copy + sizeof(struct tag_header); - return error; -} + WARN_ON(tag->hdr.tag != ATAG_NONE); + + b = kmalloc(sizeof(*b) + size, GFP_KERNEL); + if (!b) + goto nomem; + b->size = size; + memcpy(b->data, atags_copy, size); + + tags_entry = create_proc_read_entry("atags", 0400, + NULL, read_buffer, b); + + if (!tags_entry) + goto nomem; + + return 0; + +nomem: + kfree(b); + printk(KERN_ERR "Exporting ATAGs: not enough memory\n"); + + return -ENOMEM; +} arch_initcall(init_atags_procfs); diff --git a/arch/arm/kernel/ecard.c b/arch/arm/kernel/ecard.c index a53c0aba5c1..8bfd299bfe7 100644 --- a/arch/arm/kernel/ecard.c +++ b/arch/arm/kernel/ecard.c @@ -680,7 +680,7 @@ static int __init ecard_probeirqhw(void) #define IO_EC_MEMC8_BASE 0 #endif -unsigned int __ecard_address(ecard_t *ec, card_type_t type, card_speed_t speed) +static unsigned int __ecard_address(ecard_t *ec, card_type_t type, card_speed_t speed) { unsigned long address = 0; int slot = ec->slot_no; @@ -1002,7 +1002,7 @@ ecard_probe(int slot, card_type_t type) } rc = -ENODEV; - if ((ec->podaddr = ecard_address(ec, type, ECARD_SYNC)) == 0) + if ((ec->podaddr = __ecard_address(ec, type, ECARD_SYNC)) == 0) goto nodev; cid.r_zero = 1; @@ -1141,10 +1141,10 @@ static int ecard_drv_probe(struct device *dev) id = ecard_match_device(drv->id_table, ec); - ecard_claim(ec); + ec->claimed = 1; ret = drv->probe(ec, id); if (ret) - ecard_release(ec); + ec->claimed = 0; return ret; } @@ -1154,7 +1154,7 @@ static int ecard_drv_remove(struct device *dev) struct ecard_driver *drv = ECARD_DRV(dev->driver); drv->remove(ec); - ecard_release(ec); + ec->claimed = 0; /* * Restore the default operations. We ensure that the @@ -1182,7 +1182,7 @@ static void ecard_drv_shutdown(struct device *dev) if (dev->driver) { if (drv->shutdown) drv->shutdown(ec); - ecard_release(ec); + ec->claimed = 0; } /* @@ -1239,7 +1239,6 @@ static int ecard_bus_init(void) postcore_initcall(ecard_bus_init); EXPORT_SYMBOL(ecard_readchunk); -EXPORT_SYMBOL(__ecard_address); EXPORT_SYMBOL(ecard_register_driver); EXPORT_SYMBOL(ecard_remove_driver); EXPORT_SYMBOL(ecard_bus_type); diff --git a/arch/arm/kernel/ecard.h b/arch/arm/kernel/ecard.h index d7c2dacf935..4642d436be2 100644 --- a/arch/arm/kernel/ecard.h +++ b/arch/arm/kernel/ecard.h @@ -54,3 +54,16 @@ struct ex_chunk_dir { #define c_len(x) ((x)->r_len[0]|((x)->r_len[1]<<8)|((x)->r_len[2]<<16)) #define c_start(x) ((x)->r_start) }; + +typedef enum ecard_type { /* Cards address space */ + ECARD_IOC, + ECARD_MEMC, + ECARD_EASI +} card_type_t; + +typedef enum { /* Speed for ECARD_IOC space */ + ECARD_SLOW = 0, + ECARD_MEDIUM = 1, + ECARD_FAST = 2, + ECARD_SYNC = 3 +} card_speed_t; diff --git a/arch/arm/kernel/process.c b/arch/arm/kernel/process.c index 46bf2ede612..199b3680118 100644 --- a/arch/arm/kernel/process.c +++ b/arch/arm/kernel/process.c @@ -133,10 +133,8 @@ static void default_idle(void) cpu_relax(); else { local_irq_disable(); - if (!need_resched()) { - timer_dyn_reprogram(); + if (!need_resched()) arch_idle(); - } local_irq_enable(); } } diff --git a/arch/arm/kernel/stacktrace.c b/arch/arm/kernel/stacktrace.c index ae31deb2d06..90e0c35ae60 100644 --- a/arch/arm/kernel/stacktrace.c +++ b/arch/arm/kernel/stacktrace.c @@ -36,6 +36,7 @@ EXPORT_SYMBOL(walk_stackframe); #ifdef CONFIG_STACKTRACE struct stack_trace_data { struct stack_trace *trace; + unsigned int no_sched_functions; unsigned int skip; }; @@ -43,27 +44,52 @@ static int save_trace(struct stackframe *frame, void *d) { struct stack_trace_data *data = d; struct stack_trace *trace = data->trace; + unsigned long addr = frame->lr; + if (data->no_sched_functions && in_sched_functions(addr)) + return 0; if (data->skip) { data->skip--; return 0; } - trace->entries[trace->nr_entries++] = frame->lr; + trace->entries[trace->nr_entries++] = addr; return trace->nr_entries >= trace->max_entries; } -void save_stack_trace(struct stack_trace *trace) +void save_stack_trace_tsk(struct task_struct *tsk, struct stack_trace *trace) { struct stack_trace_data data; unsigned long fp, base; data.trace = trace; data.skip = trace->skip; - base = (unsigned long)task_stack_page(current); - asm("mov %0, fp" : "=r" (fp)); + base = (unsigned long)task_stack_page(tsk); + + if (tsk != current) { +#ifdef CONFIG_SMP + /* + * What guarantees do we have here that 'tsk' + * is not running on another CPU? + */ + BUG(); +#else + data.no_sched_functions = 1; + fp = thread_saved_fp(tsk); +#endif + } else { + data.no_sched_functions = 0; + asm("mov %0, fp" : "=r" (fp)); + } walk_stackframe(fp, base, base + THREAD_SIZE, save_trace, &data); + if (trace->nr_entries < trace->max_entries) + trace->entries[trace->nr_entries++] = ULONG_MAX; +} + +void save_stack_trace(struct stack_trace *trace) +{ + save_stack_trace_tsk(current, trace); } #endif diff --git a/arch/arm/kernel/time.c b/arch/arm/kernel/time.c index b5867eca1d0..cc5145b28e7 100644 --- a/arch/arm/kernel/time.c +++ b/arch/arm/kernel/time.c @@ -365,108 +365,6 @@ static struct sysdev_class timer_sysclass = { .resume = timer_resume, }; -#ifdef CONFIG_NO_IDLE_HZ -static int timer_dyn_tick_enable(void) -{ - struct dyn_tick_timer *dyn_tick = system_timer->dyn_tick; - unsigned long flags; - int ret = -ENODEV; - - if (dyn_tick) { - spin_lock_irqsave(&dyn_tick->lock, flags); - ret = 0; - if (!(dyn_tick->state & DYN_TICK_ENABLED)) { - ret = dyn_tick->enable(); - - if (ret == 0) - dyn_tick->state |= DYN_TICK_ENABLED; - } - spin_unlock_irqrestore(&dyn_tick->lock, flags); - } - - return ret; -} - -static int timer_dyn_tick_disable(void) -{ - struct dyn_tick_timer *dyn_tick = system_timer->dyn_tick; - unsigned long flags; - int ret = -ENODEV; - - if (dyn_tick) { - spin_lock_irqsave(&dyn_tick->lock, flags); - ret = 0; - if (dyn_tick->state & DYN_TICK_ENABLED) { - ret = dyn_tick->disable(); - - if (ret == 0) - dyn_tick->state &= ~DYN_TICK_ENABLED; - } - spin_unlock_irqrestore(&dyn_tick->lock, flags); - } - - return ret; -} - -/* - * Reprogram the system timer for at least the calculated time interval. - * This function should be called from the idle thread with IRQs disabled, - * immediately before sleeping. - */ -void timer_dyn_reprogram(void) -{ - struct dyn_tick_timer *dyn_tick = system_timer->dyn_tick; - unsigned long next, seq, flags; - - if (!dyn_tick) - return; - - spin_lock_irqsave(&dyn_tick->lock, flags); - if (dyn_tick->state & DYN_TICK_ENABLED) { - next = next_timer_interrupt(); - do { - seq = read_seqbegin(&xtime_lock); - dyn_tick->reprogram(next - jiffies); - } while (read_seqretry(&xtime_lock, seq)); - } - spin_unlock_irqrestore(&dyn_tick->lock, flags); -} - -static ssize_t timer_show_dyn_tick(struct sys_device *dev, char *buf) -{ - return sprintf(buf, "%i\n", - (system_timer->dyn_tick->state & DYN_TICK_ENABLED) >> 1); -} - -static ssize_t timer_set_dyn_tick(struct sys_device *dev, const char *buf, - size_t count) -{ - unsigned int enable = simple_strtoul(buf, NULL, 2); - - if (enable) - timer_dyn_tick_enable(); - else - timer_dyn_tick_disable(); - - return count; -} -static SYSDEV_ATTR(dyn_tick, 0644, timer_show_dyn_tick, timer_set_dyn_tick); - -/* - * dyntick=enable|disable - */ -static char dyntick_str[4] __initdata = ""; - -static int __init dyntick_setup(char *str) -{ - if (str) - strlcpy(dyntick_str, str, sizeof(dyntick_str)); - return 1; -} - -__setup("dyntick=", dyntick_setup); -#endif - static int __init timer_init_sysfs(void) { int ret = sysdev_class_register(&timer_sysclass); @@ -475,19 +373,6 @@ static int __init timer_init_sysfs(void) ret = sysdev_register(&system_timer->dev); } -#ifdef CONFIG_NO_IDLE_HZ - if (ret == 0 && system_timer->dyn_tick) { - ret = sysdev_create_file(&system_timer->dev, &attr_dyn_tick); - - /* - * Turn on dynamic tick after calibrate delay - * for correct bogomips - */ - if (ret == 0 && dyntick_str[0] == 'e') - ret = timer_dyn_tick_enable(); - } -#endif - return ret; } @@ -500,10 +385,5 @@ void __init time_init(void) system_timer->offset = dummy_gettimeoffset; #endif system_timer->init(); - -#ifdef CONFIG_NO_IDLE_HZ - if (system_timer->dyn_tick) - spin_lock_init(&system_timer->dyn_tick->lock); -#endif } diff --git a/arch/arm/lib/copy_template.S b/arch/arm/lib/copy_template.S index cab355c0c1f..139cce64605 100644 --- a/arch/arm/lib/copy_template.S +++ b/arch/arm/lib/copy_template.S @@ -13,14 +13,6 @@ */ /* - * This can be used to enable code to cacheline align the source pointer. - * Experiments on tested architectures (StrongARM and XScale) didn't show - * this a worthwhile thing to do. That might be different in the future. - */ -//#define CALGN(code...) code -#define CALGN(code...) - -/* * Theory of operation * ------------------- * @@ -82,7 +74,7 @@ stmfd sp!, {r5 - r8} blt 5f - CALGN( ands ip, r1, #31 ) + CALGN( ands ip, r0, #31 ) CALGN( rsb r3, ip, #32 ) CALGN( sbcnes r4, r3, r2 ) @ C is always set here CALGN( bcs 2f ) @@ -168,7 +160,7 @@ subs r2, r2, #28 blt 14f - CALGN( ands ip, r1, #31 ) + CALGN( ands ip, r0, #31 ) CALGN( rsb ip, ip, #32 ) CALGN( sbcnes r4, ip, r2 ) @ C is always set here CALGN( subcc r2, r2, ip ) diff --git a/arch/arm/lib/memmove.S b/arch/arm/lib/memmove.S index ef7fddc14ac..2e301b7bd8f 100644 --- a/arch/arm/lib/memmove.S +++ b/arch/arm/lib/memmove.S @@ -13,14 +13,6 @@ #include <linux/linkage.h> #include <asm/assembler.h> -/* - * This can be used to enable code to cacheline align the source pointer. - * Experiments on tested architectures (StrongARM and XScale) didn't show - * this a worthwhile thing to do. That might be different in the future. - */ -//#define CALGN(code...) code -#define CALGN(code...) - .text /* @@ -55,11 +47,12 @@ ENTRY(memmove) stmfd sp!, {r5 - r8} blt 5f - CALGN( ands ip, r1, #31 ) + CALGN( ands ip, r0, #31 ) CALGN( sbcnes r4, ip, r2 ) @ C is always set here CALGN( bcs 2f ) CALGN( adr r4, 6f ) CALGN( subs r2, r2, ip ) @ C is set here + CALGN( rsb ip, ip, #32 ) CALGN( add pc, r4, ip ) PLD( pld [r1, #-4] ) @@ -138,8 +131,7 @@ ENTRY(memmove) subs r2, r2, #28 blt 14f - CALGN( ands ip, r1, #31 ) - CALGN( rsb ip, ip, #32 ) + CALGN( ands ip, r0, #31 ) CALGN( sbcnes r4, ip, r2 ) @ C is always set here CALGN( subcc r2, r2, ip ) CALGN( bcc 15f ) diff --git a/arch/arm/lib/memset.S b/arch/arm/lib/memset.S index 95b110b07a8..b477d4ac88e 100644 --- a/arch/arm/lib/memset.S +++ b/arch/arm/lib/memset.S @@ -39,6 +39,9 @@ ENTRY(memset) mov r3, r1 cmp r2, #16 blt 4f + +#if ! CALGN(1)+0 + /* * We need an extra register for this loop - save the return address and * use the LR @@ -64,6 +67,49 @@ ENTRY(memset) stmneia r0!, {r1, r3, ip, lr} ldr lr, [sp], #4 +#else + +/* + * This version aligns the destination pointer in order to write + * whole cache lines at once. + */ + + stmfd sp!, {r4-r7, lr} + mov r4, r1 + mov r5, r1 + mov r6, r1 + mov r7, r1 + mov ip, r1 + mov lr, r1 + + cmp r2, #96 + tstgt r0, #31 + ble 3f + + and ip, r0, #31 + rsb ip, ip, #32 + sub r2, r2, ip + movs ip, ip, lsl #(32 - 4) + stmcsia r0!, {r4, r5, r6, r7} + stmmiia r0!, {r4, r5} + tst ip, #(1 << 30) + mov ip, r1 + strne r1, [r0], #4 + +3: subs r2, r2, #64 + stmgeia r0!, {r1, r3-r7, ip, lr} + stmgeia r0!, {r1, r3-r7, ip, lr} + bgt 3b + ldmeqfd sp!, {r4-r7, pc} + + tst r2, #32 + stmneia r0!, {r1, r3-r7, ip, lr} + tst r2, #16 + stmneia r0!, {r4-r7} + ldmfd sp!, {r4-r7, lr} + +#endif + 4: tst r2, #8 stmneia r0!, {r1, r3} tst r2, #4 diff --git a/arch/arm/lib/memzero.S b/arch/arm/lib/memzero.S index abf2508e822..b8f79d80ee9 100644 --- a/arch/arm/lib/memzero.S +++ b/arch/arm/lib/memzero.S @@ -39,6 +39,9 @@ ENTRY(__memzero) */ cmp r1, #16 @ 1 we can skip this chunk if we blt 4f @ 1 have < 16 bytes + +#if ! CALGN(1)+0 + /* * We need an extra register for this loop - save the return address and * use the LR @@ -64,6 +67,47 @@ ENTRY(__memzero) stmneia r0!, {r2, r3, ip, lr} @ 4 ldr lr, [sp], #4 @ 1 +#else + +/* + * This version aligns the destination pointer in order to write + * whole cache lines at once. + */ + + stmfd sp!, {r4-r7, lr} + mov r4, r2 + mov r5, r2 + mov r6, r2 + mov r7, r2 + mov ip, r2 + mov lr, r2 + + cmp r1, #96 + andgts ip, r0, #31 + ble 3f + + rsb ip, ip, #32 + sub r1, r1, ip + movs ip, ip, lsl #(32 - 4) + stmcsia r0!, {r4, r5, r6, r7} + stmmiia r0!, {r4, r5} + movs ip, ip, lsl #2 + strcs r2, [r0], #4 + +3: subs r1, r1, #64 + stmgeia r0!, {r2-r7, ip, lr} + stmgeia r0!, {r2-r7, ip, lr} + bgt 3b + ldmeqfd sp!, {r4-r7, pc} + + tst r1, #32 + stmneia r0!, {r2-r7, ip, lr} + tst r1, #16 + stmneia r0!, {r4-r7} + ldmfd sp!, {r4-r7, lr} + +#endif + 4: tst r1, #8 @ 1 8 bytes or more? stmneia r0!, {r2, r3} @ 2 tst r1, #4 @ 1 4 bytes or more? diff --git a/arch/arm/mach-at91/Kconfig b/arch/arm/mach-at91/Kconfig index 0fc07b6db74..5bad6b9b00d 100644 --- a/arch/arm/mach-at91/Kconfig +++ b/arch/arm/mach-at91/Kconfig @@ -30,6 +30,11 @@ config ARCH_AT91SAM9RL select GENERIC_TIME select GENERIC_CLOCKEVENTS +config ARCH_AT91SAM9G20 + bool "AT91SAM9G20" + select GENERIC_TIME + select GENERIC_CLOCKEVENTS + config ARCH_AT91CAP9 bool "AT91CAP9" select GENERIC_TIME @@ -126,6 +131,12 @@ config MACH_ECBAT91 Select this if you are using emQbit's ECB_AT91 board. <http://wiki.emqbit.com/free-ecb-at91> +config MACH_YL9200 + bool "ucDragon YL-9200" + depends on ARCH_AT91RM9200 + help + Select this if you are using the ucDragon YL-9200 board. + endif # ---------------------------------------------------------- @@ -164,6 +175,20 @@ config MACH_SAM9_L9260 Select this if you are using Olimex's SAM9-L9260 board based on the Atmel AT91SAM9260. <http://www.olimex.com/dev/sam9-L9260.html> +config MACH_USB_A9260 + bool "CALAO USB-A9260" + depends on ARCH_AT91SAM9260 + help + Select this if you are using a Calao Systems USB-A9260. + <http://www.calao-systems.com> + +config MACH_QIL_A9260 + bool "CALAO QIL-A9260 board" + depends on ARCH_AT91SAM9260 + help + Select this if you are using a Calao Systems QIL-A9260 Board. + <http://www.calao-systems.com> + endif # ---------------------------------------------------------- @@ -194,6 +219,13 @@ config MACH_AT91SAM9263EK Select this if you are using Atmel's AT91SAM9263-EK Evaluation Kit. <http://www.atmel.com/dyn/products/tools_card.asp?tool_id=4057> +config MACH_USB_A9263 + bool "CALAO USB-A9263" + depends on ARCH_AT91SAM9263 + help + Select this if you are using a Calao Systems USB-A9263. + <http://www.calao-systems.com> + endif # ---------------------------------------------------------- @@ -212,6 +244,20 @@ endif # ---------------------------------------------------------- +if ARCH_AT91SAM9G20 + +comment "AT91SAM9G20 Board Type" + +config MACH_AT91SAM9G20EK + bool "Atmel AT91SAM9G20-EK Evaluation Kit" + depends on ARCH_AT91SAM9G20 + help + Select this if you are using Atmel's AT91SAM9G20-EK Evaluation Kit. + +endif + +# ---------------------------------------------------------- + if ARCH_AT91CAP9 comment "AT91CAP9 Board Type" @@ -247,13 +293,13 @@ comment "AT91 Board Options" config MTD_AT91_DATAFLASH_CARD bool "Enable DataFlash Card support" - depends on (ARCH_AT91RM9200DK || MACH_AT91RM9200EK || MACH_AT91SAM9260EK || MACH_AT91SAM9261EK || MACH_AT91SAM9263EK || MACH_AT91CAP9ADK || MACH_SAM9_L9260 || MACH_ECBAT91) + depends on (ARCH_AT91RM9200DK || MACH_AT91RM9200EK || MACH_AT91SAM9260EK || MACH_AT91SAM9261EK || MACH_AT91SAM9263EK || MACH_AT91SAM9G20EK || MACH_ECBAT91 || MACH_SAM9_L9260 || MACH_AT91CAP9ADK) help Enable support for the DataFlash card. config MTD_NAND_AT91_BUSWIDTH_16 bool "Enable 16-bit data bus interface to NAND flash" - depends on (MACH_AT91SAM9260EK || MACH_AT91SAM9261EK || MACH_AT91SAM9263EK || MACH_AT91CAP9ADK) + depends on (MACH_AT91SAM9260EK || MACH_AT91SAM9261EK || MACH_AT91SAM9263EK || MACH_AT91SAM9G20EK || MACH_AT91CAP9ADK) help On AT91SAM926x boards both types of NAND flash can be present (8 and 16 bit data bus width). @@ -302,15 +348,15 @@ config AT91_EARLY_USART2 config AT91_EARLY_USART3 bool "USART3" - depends on (ARCH_AT91RM9200 || ARCH_AT91SAM9RL || ARCH_AT91SAM9260) + depends on (ARCH_AT91RM9200 || ARCH_AT91SAM9RL || ARCH_AT91SAM9260 || ARCH_AT91SAM9G20) config AT91_EARLY_USART4 bool "USART4" - depends on ARCH_AT91SAM9260 + depends on ARCH_AT91SAM9260 || ARCH_AT91SAM9G20 config AT91_EARLY_USART5 bool "USART5" - depends on ARCH_AT91SAM9260 + depends on ARCH_AT91SAM9260 || ARCH_AT91SAM9G20 endchoice diff --git a/arch/arm/mach-at91/Makefile b/arch/arm/mach-at91/Makefile index 8d9bc0153b1..7d641f97516 100644 --- a/arch/arm/mach-at91/Makefile +++ b/arch/arm/mach-at91/Makefile @@ -15,6 +15,7 @@ obj-$(CONFIG_ARCH_AT91SAM9260) += at91sam9260.o at91sam926x_time.o at91sam9260_d obj-$(CONFIG_ARCH_AT91SAM9261) += at91sam9261.o at91sam926x_time.o at91sam9261_devices.o obj-$(CONFIG_ARCH_AT91SAM9263) += at91sam9263.o at91sam926x_time.o at91sam9263_devices.o obj-$(CONFIG_ARCH_AT91SAM9RL) += at91sam9rl.o at91sam926x_time.o at91sam9rl_devices.o +obj-$(CONFIG_ARCH_AT91SAM9G20) += at91sam9260.o at91sam926x_time.o at91sam9260_devices.o obj-$(CONFIG_ARCH_AT91CAP9) += at91cap9.o at91sam926x_time.o at91cap9_devices.o obj-$(CONFIG_ARCH_AT91X40) += at91x40.o at91x40_time.o @@ -30,21 +31,28 @@ obj-$(CONFIG_MACH_ATEB9200) += board-eb9200.o obj-$(CONFIG_MACH_KAFA) += board-kafa.o obj-$(CONFIG_MACH_PICOTUX2XX) += board-picotux200.o obj-$(CONFIG_MACH_ECBAT91) += board-ecbat91.o +obj-$(CONFIG_MACH_YL9200) += board-yl-9200.o # AT91SAM9260 board-specific support obj-$(CONFIG_MACH_AT91SAM9260EK) += board-sam9260ek.o obj-$(CONFIG_MACH_CAM60) += board-cam60.o obj-$(CONFIG_MACH_SAM9_L9260) += board-sam9-l9260.o +obj-$(CONFIG_MACH_USB_A9260) += board-usb-a9260.o +obj-$(CONFIG_MACH_QIL_A9260) += board-qil-a9260.o # AT91SAM9261 board-specific support obj-$(CONFIG_MACH_AT91SAM9261EK) += board-sam9261ek.o # AT91SAM9263 board-specific support obj-$(CONFIG_MACH_AT91SAM9263EK) += board-sam9263ek.o +obj-$(CONFIG_MACH_USB_A9263) += board-usb-a9263.o # AT91SAM9RL board-specific support obj-$(CONFIG_MACH_AT91SAM9RLEK) += board-sam9rlek.o +# AT91SAM9G20 board-specific support +obj-$(CONFIG_MACH_AT91SAM9G20EK) += board-sam9g20ek.o + # AT91CAP9 board-specific support obj-$(CONFIG_MACH_AT91CAP9ADK) += board-cap9adk.o diff --git a/arch/arm/mach-at91/at91cap9_devices.c b/arch/arm/mach-at91/at91cap9_devices.c index be526746e01..747b9dedab8 100644 --- a/arch/arm/mach-at91/at91cap9_devices.c +++ b/arch/arm/mach-at91/at91cap9_devices.c @@ -84,6 +84,105 @@ void __init at91_add_device_usbh(struct at91_usbh_data *data) {} /* -------------------------------------------------------------------- + * USB HS Device (Gadget) + * -------------------------------------------------------------------- */ + +#if defined(CONFIG_USB_GADGET_ATMEL_USBA) || defined(CONFIG_USB_GADGET_ATMEL_USBA_MODULE) + +static struct resource usba_udc_resources[] = { + [0] = { + .start = AT91CAP9_UDPHS_FIFO, + .end = AT91CAP9_UDPHS_FIFO + SZ_512K - 1, + .flags = IORESOURCE_MEM, + }, + [1] = { + .start = AT91CAP9_BASE_UDPHS, + .end = AT91CAP9_BASE_UDPHS + SZ_1K - 1, + .flags = IORESOURCE_MEM, + }, + [2] = { + .start = AT91CAP9_ID_UDPHS, + .end = AT91CAP9_ID_UDPHS, + .flags = IORESOURCE_IRQ, + }, +}; + +#define EP(nam, idx, maxpkt, maxbk, dma, isoc) \ + [idx] = { \ + .name = nam, \ + .index = idx, \ + .fifo_size = maxpkt, \ + .nr_banks = maxbk, \ + .can_dma = dma, \ + .can_isoc = isoc, \ + } + +static struct usba_ep_data usba_udc_ep[] = { + EP("ep0", 0, 64, 1, 0, 0), + EP("ep1", 1, 1024, 3, 1, 1), + EP("ep2", 2, 1024, 3, 1, 1), + EP("ep3", 3, 1024, 2, 1, 1), + EP("ep4", 4, 1024, 2, 1, 1), + EP("ep5", 5, 1024, 2, 1, 0), + EP("ep6", 6, 1024, 2, 1, 0), + EP("ep7", 7, 1024, 2, 0, 0), +}; + +#undef EP + +/* + * pdata doesn't have room for any endpoints, so we need to + * append room for the ones we need right after it. + */ +static struct { + struct usba_platform_data pdata; + struct usba_ep_data ep[8]; +} usba_udc_data; + +static struct platform_device at91_usba_udc_device = { + .name = "atmel_usba_udc", + .id = -1, + .dev = { + .platform_data = &usba_udc_data.pdata, + }, + .resource = usba_udc_resources, + .num_resources = ARRAY_SIZE(usba_udc_resources), +}; + +void __init at91_add_device_usba(struct usba_platform_data *data) +{ + at91_sys_write(AT91_MATRIX_UDPHS, AT91_MATRIX_SELECT_UDPHS | + AT91_MATRIX_UDPHS_BYPASS_LOCK); + + /* + * Invalid pins are 0 on AT91, but the usba driver is shared + * with AVR32, which use negative values instead. Once/if + * gpio_is_valid() is ported to AT91, revisit this code. + */ + usba_udc_data.pdata.vbus_pin = -EINVAL; + usba_udc_data.pdata.num_ep = ARRAY_SIZE(usba_udc_ep); + memcpy(usba_udc_data.ep, usba_udc_ep, sizeof(usba_udc_ep));; + + if (data && data->vbus_pin > 0) { + at91_set_gpio_input(data->vbus_pin, 0); + at91_set_deglitch(data->vbus_pin, 1); + usba_udc_data.pdata.vbus_pin = data->vbus_pin; + } + + /* Pullup pin is handled internally by USB device peripheral */ + + /* Clocks */ + at91_clock_associate("utmi_clk", &at91_usba_udc_device.dev, "hclk"); + at91_clock_associate("udphs_clk", &at91_usba_udc_device.dev, "pclk"); + + platform_device_register(&at91_usba_udc_device); +} +#else +void __init at91_add_device_usba(struct usba_platform_data *data) {} +#endif + + +/* -------------------------------------------------------------------- * Ethernet * -------------------------------------------------------------------- */ diff --git a/arch/arm/mach-at91/at91sam9260.c b/arch/arm/mach-at91/at91sam9260.c index ee26550cdc2..380f12a1220 100644 --- a/arch/arm/mach-at91/at91sam9260.c +++ b/arch/arm/mach-at91/at91sam9260.c @@ -47,6 +47,20 @@ static struct map_desc at91sam9260_sram_desc[] __initdata = { } }; +static struct map_desc at91sam9g20_sram_desc[] __initdata = { + { + .virtual = AT91_IO_VIRT_BASE - AT91SAM9G20_SRAM0_SIZE, + .pfn = __phys_to_pfn(AT91SAM9G20_SRAM0_BASE), + .length = AT91SAM9G20_SRAM0_SIZE, + .type = MT_DEVICE, + }, { + .virtual = AT91_IO_VIRT_BASE - AT91SAM9G20_SRAM0_SIZE - AT91SAM9G20_SRAM1_SIZE, + .pfn = __phys_to_pfn(AT91SAM9G20_SRAM1_BASE), + .length = AT91SAM9G20_SRAM1_SIZE, + .type = MT_DEVICE, + } +}; + static struct map_desc at91sam9xe_sram_desc[] __initdata = { { .pfn = __phys_to_pfn(AT91SAM9XE_SRAM_BASE), @@ -307,6 +321,8 @@ void __init at91sam9260_initialize(unsigned long main_clock) if (cpu_is_at91sam9xe()) at91sam9xe_initialize(); + else if (cpu_is_at91sam9g20()) + iotable_init(at91sam9g20_sram_desc, ARRAY_SIZE(at91sam9g20_sram_desc)); else iotable_init(at91sam9260_sram_desc, ARRAY_SIZE(at91sam9260_sram_desc)); diff --git a/arch/arm/mach-at91/at91sam9260_devices.c b/arch/arm/mach-at91/at91sam9260_devices.c index 393a32aefce..86cba4ac29b 100644 --- a/arch/arm/mach-at91/at91sam9260_devices.c +++ b/arch/arm/mach-at91/at91sam9260_devices.c @@ -18,6 +18,7 @@ #include <asm/arch/board.h> #include <asm/arch/gpio.h> +#include <asm/arch/cpu.h> #include <asm/arch/at91sam9260.h> #include <asm/arch/at91sam9260_matrix.h> #include <asm/arch/at91sam9_smc.h> @@ -320,20 +321,41 @@ void __init at91_add_device_nand(struct at91_nand_data *data) csa = at91_sys_read(AT91_MATRIX_EBICSA); at91_sys_write(AT91_MATRIX_EBICSA, csa | AT91_MATRIX_CS3A_SMC_SMARTMEDIA); - /* set the bus interface characteristics */ - at91_sys_write(AT91_SMC_SETUP(3), AT91_SMC_NWESETUP_(0) | AT91_SMC_NCS_WRSETUP_(0) - | AT91_SMC_NRDSETUP_(0) | AT91_SMC_NCS_RDSETUP_(0)); + if (cpu_is_at91sam9260()) { + /* Timing for sam9260 */ + /* set the bus interface characteristics */ + at91_sys_write(AT91_SMC_SETUP(3), AT91_SMC_NWESETUP_(1) | AT91_SMC_NCS_WRSETUP_(0) + | AT91_SMC_NRDSETUP_(1) | AT91_SMC_NCS_RDSETUP_(0)); - at91_sys_write(AT91_SMC_PULSE(3), AT91_SMC_NWEPULSE_(3) | AT91_SMC_NCS_WRPULSE_(3) - | AT91_SMC_NRDPULSE_(3) | AT91_SMC_NCS_RDPULSE_(3)); + at91_sys_write(AT91_SMC_PULSE(3), AT91_SMC_NWEPULSE_(3) | AT91_SMC_NCS_WRPULSE_(3) + | AT91_SMC_NRDPULSE_(3) | AT91_SMC_NCS_RDPULSE_(3)); - at91_sys_write(AT91_SMC_CYCLE(3), AT91_SMC_NWECYCLE_(5) | AT91_SMC_NRDCYCLE_(5)); + at91_sys_write(AT91_SMC_CYCLE(3), AT91_SMC_NWECYCLE_(5) | AT91_SMC_NRDCYCLE_(5)); - if (data->bus_width_16) - mode = AT91_SMC_DBW_16; - else - mode = AT91_SMC_DBW_8; - at91_sys_write(AT91_SMC_MODE(3), mode | AT91_SMC_READMODE | AT91_SMC_WRITEMODE | AT91_SMC_EXNWMODE_DISABLE | AT91_SMC_TDF_(2)); + if (data->bus_width_16) + mode = AT91_SMC_DBW_16; + else + mode = AT91_SMC_DBW_8; + at91_sys_write(AT91_SMC_MODE(3), mode | AT91_SMC_READMODE | AT91_SMC_WRITEMODE | AT91_SMC_EXNWMODE_DISABLE | AT91_SMC_TDF_(2)); + } + + if (cpu_is_at91sam9g20()) { + /* Timing for sam9g20 */ + /* set the bus interface characteristics */ + at91_sys_write(AT91_SMC_SETUP(3), AT91_SMC_NWESETUP_(2) | AT91_SMC_NCS_WRSETUP_(0) + | AT91_SMC_NRDSETUP_(2) | AT91_SMC_NCS_RDSETUP_(0)); + + at91_sys_write(AT91_SMC_PULSE(3), AT91_SMC_NWEPULSE_(4) | AT91_SMC_NCS_WRPULSE_(4) + | AT91_SMC_NRDPULSE_(4) | AT91_SMC_NCS_RDPULSE_(4)); + + at91_sys_write(AT91_SMC_CYCLE(3), AT91_SMC_NWECYCLE_(7) | AT91_SMC_NRDCYCLE_(7)); + + if (data->bus_width_16) + mode = AT91_SMC_DBW_16; + else + mode = AT91_SMC_DBW_8; + at91_sys_write(AT91_SMC_MODE(3), mode | AT91_SMC_READMODE | AT91_SMC_WRITEMODE | AT91_SMC_EXNWMODE_DISABLE | AT91_SMC_TDF_(3)); + } /* enable pin */ if (data->enable_pin) diff --git a/arch/arm/mach-at91/at91sam9261_devices.c b/arch/arm/mach-at91/at91sam9261_devices.c index 0babb645b83..ec1891375df 100644 --- a/arch/arm/mach-at91/at91sam9261_devices.c +++ b/arch/arm/mach-at91/at91sam9261_devices.c @@ -232,19 +232,19 @@ void __init at91_add_device_nand(struct at91_nand_data *data) at91_sys_write(AT91_MATRIX_EBICSA, csa | AT91_MATRIX_CS3A_SMC_SMARTMEDIA); /* set the bus interface characteristics */ - at91_sys_write(AT91_SMC_SETUP(3), AT91_SMC_NWESETUP_(0) | AT91_SMC_NCS_WRSETUP_(0) - | AT91_SMC_NRDSETUP_(0) | AT91_SMC_NCS_RDSETUP_(0)); + at91_sys_write(AT91_SMC_SETUP(3), AT91_SMC_NWESETUP_(1) | AT91_SMC_NCS_WRSETUP_(0) + | AT91_SMC_NRDSETUP_(1) | AT91_SMC_NCS_RDSETUP_(0)); - at91_sys_write(AT91_SMC_PULSE(3), AT91_SMC_NWEPULSE_(2) | AT91_SMC_NCS_WRPULSE_(5) - | AT91_SMC_NRDPULSE_(2) | AT91_SMC_NCS_RDPULSE_(5)); + at91_sys_write(AT91_SMC_PULSE(3), AT91_SMC_NWEPULSE_(3) | AT91_SMC_NCS_WRPULSE_(3) + | AT91_SMC_NRDPULSE_(3) | AT91_SMC_NCS_RDPULSE_(3)); - at91_sys_write(AT91_SMC_CYCLE(3), AT91_SMC_NWECYCLE_(7) | AT91_SMC_NRDCYCLE_(7)); + at91_sys_write(AT91_SMC_CYCLE(3), AT91_SMC_NWECYCLE_(5) | AT91_SMC_NRDCYCLE_(5)); if (data->bus_width_16) mode = AT91_SMC_DBW_16; else mode = AT91_SMC_DBW_8; - at91_sys_write(AT91_SMC_MODE(3), mode | AT91_SMC_READMODE | AT91_SMC_WRITEMODE | AT91_SMC_EXNWMODE_DISABLE | AT91_SMC_TDF_(1)); + at91_sys_write(AT91_SMC_MODE(3), mode | AT91_SMC_READMODE | AT91_SMC_WRITEMODE | AT91_SMC_EXNWMODE_DISABLE | AT91_SMC_TDF_(2)); /* enable pin */ if (data->enable_pin) diff --git a/arch/arm/mach-at91/at91sam9263_devices.c b/arch/arm/mach-at91/at91sam9263_devices.c index 719667e25c9..8a81f76f020 100644 --- a/arch/arm/mach-at91/at91sam9263_devices.c +++ b/arch/arm/mach-at91/at91sam9263_devices.c @@ -391,8 +391,8 @@ void __init at91_add_device_nand(struct at91_nand_data *data) at91_sys_write(AT91_MATRIX_EBI0CSA, csa | AT91_MATRIX_EBI0_CS3A_SMC_SMARTMEDIA); /* set the bus interface characteristics */ - at91_sys_write(AT91_SMC_SETUP(3), AT91_SMC_NWESETUP_(0) | AT91_SMC_NCS_WRSETUP_(0) - | AT91_SMC_NRDSETUP_(0) | AT91_SMC_NCS_RDSETUP_(0)); + at91_sys_write(AT91_SMC_SETUP(3), AT91_SMC_NWESETUP_(1) | AT91_SMC_NCS_WRSETUP_(0) + | AT91_SMC_NRDSETUP_(1) | AT91_SMC_NCS_RDSETUP_(0)); at91_sys_write(AT91_SMC_PULSE(3), AT91_SMC_NWEPULSE_(3) | AT91_SMC_NCS_WRPULSE_(3) | AT91_SMC_NRDPULSE_(3) | AT91_SMC_NCS_RDPULSE_(3)); diff --git a/arch/arm/mach-at91/at91sam9rl_devices.c b/arch/arm/mach-at91/at91sam9rl_devices.c index 450db304936..ae28101e754 100644 --- a/arch/arm/mach-at91/at91sam9rl_devices.c +++ b/arch/arm/mach-at91/at91sam9rl_devices.c @@ -26,6 +26,101 @@ /* -------------------------------------------------------------------- + * USB HS Device (Gadget) + * -------------------------------------------------------------------- */ + +#if defined(CONFIG_USB_GADGET_ATMEL_USBA) || defined(CONFIG_USB_GADGET_ATMEL_USBA_MODULE) + +static struct resource usba_udc_resources[] = { + [0] = { + .start = AT91SAM9RL_UDPHS_FIFO, + .end = AT91SAM9RL_UDPHS_FIFO + SZ_512K - 1, + .flags = IORESOURCE_MEM, + }, + [1] = { + .start = AT91SAM9RL_BASE_UDPHS, + .end = AT91SAM9RL_BASE_UDPHS + SZ_1K - 1, + .flags = IORESOURCE_MEM, + }, + [2] = { + .start = AT91SAM9RL_ID_UDPHS, + .end = AT91SAM9RL_ID_UDPHS, + .flags = IORESOURCE_IRQ, + }, +}; + +#define EP(nam, idx, maxpkt, maxbk, dma, isoc) \ + [idx] = { \ + .name = nam, \ + .index = idx, \ + .fifo_size = maxpkt, \ + .nr_banks = maxbk, \ + .can_dma = dma, \ + .can_isoc = isoc, \ + } + +static struct usba_ep_data usba_udc_ep[] __initdata = { + EP("ep0", 0, 64, 1, 0, 0), + EP("ep1", 1, 1024, 2, 1, 1), + EP("ep2", 2, 1024, 2, 1, 1), + EP("ep3", 3, 1024, 3, 1, 0), + EP("ep4", 4, 1024, 3, 1, 0), + EP("ep5", 5, 1024, 3, 1, 1), + EP("ep6", 6, 1024, 3, 1, 1), +}; + +#undef EP + +/* + * pdata doesn't have room for any endpoints, so we need to + * append room for the ones we need right after it. + */ +static struct { + struct usba_platform_data pdata; + struct usba_ep_data ep[7]; +} usba_udc_data; + +static struct platform_device at91_usba_udc_device = { + .name = "atmel_usba_udc", + .id = -1, + .dev = { + .platform_data = &usba_udc_data.pdata, + }, + .resource = usba_udc_resources, + .num_resources = ARRAY_SIZE(usba_udc_resources), +}; + +void __init at91_add_device_usba(struct usba_platform_data *data) +{ + /* + * Invalid pins are 0 on AT91, but the usba driver is shared + * with AVR32, which use negative values instead. Once/if + * gpio_is_valid() is ported to AT91, revisit this code. + */ + usba_udc_data.pdata.vbus_pin = -EINVAL; + usba_udc_data.pdata.num_ep = ARRAY_SIZE(usba_udc_ep); + memcpy(usba_udc_data.ep, usba_udc_ep, sizeof(usba_udc_ep));; + + if (data && data->vbus_pin > 0) { + at91_set_gpio_input(data->vbus_pin, 0); + at91_set_deglitch(data->vbus_pin, 1); + usba_udc_data.pdata.vbus_pin = data->vbus_pin; + } + + /* Pullup pin is handled internally by USB device peripheral */ + + /* Clocks */ + at91_clock_associate("utmi_clk", &at91_usba_udc_device.dev, "hclk"); + at91_clock_associate("udphs_clk", &at91_usba_udc_device.dev, "pclk"); + + platform_device_register(&at91_usba_udc_device); +} +#else +void __init at91_add_device_usba(struct usba_platform_data *data) {} +#endif + + +/* -------------------------------------------------------------------- * MMC / SD * -------------------------------------------------------------------- */ @@ -138,15 +233,15 @@ void __init at91_add_device_nand(struct at91_nand_data *data) at91_sys_write(AT91_MATRIX_EBICSA, csa | AT91_MATRIX_CS3A_SMC_SMARTMEDIA); /* set the bus interface characteristics */ - at91_sys_write(AT91_SMC_SETUP(3), AT91_SMC_NWESETUP_(0) | AT91_SMC_NCS_WRSETUP_(0) - | AT91_SMC_NRDSETUP_(0) | AT91_SMC_NCS_RDSETUP_(0)); + at91_sys_write(AT91_SMC_SETUP(3), AT91_SMC_NWESETUP_(1) | AT91_SMC_NCS_WRSETUP_(0) + | AT91_SMC_NRDSETUP_(1) | AT91_SMC_NCS_RDSETUP_(0)); - at91_sys_write(AT91_SMC_PULSE(3), AT91_SMC_NWEPULSE_(2) | AT91_SMC_NCS_WRPULSE_(5) - | AT91_SMC_NRDPULSE_(2) | AT91_SMC_NCS_RDPULSE_(5)); + at91_sys_write(AT91_SMC_PULSE(3), AT91_SMC_NWEPULSE_(3) | AT91_SMC_NCS_WRPULSE_(3) + | AT91_SMC_NRDPULSE_(3) | AT91_SMC_NCS_RDPULSE_(3)); - at91_sys_write(AT91_SMC_CYCLE(3), AT91_SMC_NWECYCLE_(7) | AT91_SMC_NRDCYCLE_(7)); + at91_sys_write(AT91_SMC_CYCLE(3), AT91_SMC_NWECYCLE_(5) | AT91_SMC_NRDCYCLE_(5)); - at91_sys_write(AT91_SMC_MODE(3), AT91_SMC_DBW_8 | AT91_SMC_READMODE | AT91_SMC_WRITEMODE | AT91_SMC_EXNWMODE_DISABLE | AT91_SMC_TDF_(1)); + at91_sys_write(AT91_SMC_MODE(3), AT91_SMC_DBW_8 | AT91_SMC_READMODE | AT91_SMC_WRITEMODE | AT91_SMC_EXNWMODE_DISABLE | AT91_SMC_TDF_(2)); /* enable pin */ if (data->enable_pin) diff --git a/arch/arm/mach-at91/board-cap9adk.c b/arch/arm/mach-at91/board-cap9adk.c index e5512d1ff21..8a2a958639d 100644 --- a/arch/arm/mach-at91/board-cap9adk.c +++ b/arch/arm/mach-at91/board-cap9adk.c @@ -78,6 +78,12 @@ static struct at91_usbh_data __initdata cap9adk_usbh_data = { .ports = 2, }; +/* + * USB HS Device port + */ +static struct usba_platform_data __initdata cap9adk_usba_udc_data = { + .vbus_pin = AT91_PIN_PB31, +}; /* * ADS7846 Touchscreen @@ -326,6 +332,9 @@ static void __init cap9adk_board_init(void) /* USB Host */ set_irq_type(AT91CAP9_ID_UHP, IRQT_HIGH); at91_add_device_usbh(&cap9adk_usbh_data); + /* USB HS */ + set_irq_type(AT91CAP9_ID_UDPHS, IRQT_HIGH); + at91_add_device_usba(&cap9adk_usba_udc_data); /* SPI */ at91_add_device_spi(cap9adk_spi_devices, ARRAY_SIZE(cap9adk_spi_devices)); /* Touchscreen */ diff --git a/arch/arm/mach-at91/board-carmeva.c b/arch/arm/mach-at91/board-carmeva.c index 0f0878294a6..9854fc3dd1f 100644 --- a/arch/arm/mach-at91/board-carmeva.c +++ b/arch/arm/mach-at91/board-carmeva.c @@ -40,24 +40,21 @@ #include "generic.h" -/* - * Serial port configuration. - * 0 .. 3 = USART0 .. USART3 - * 4 = DBGU - */ -static struct at91_uart_config __initdata carmeva_uart_config = { - .console_tty = 0, /* ttyS0 */ - .nr_tty = 2, - .tty_map = { 4, 1, -1, -1, -1 } /* ttyS0, ..., ttyS4 */ -}; - static void __init carmeva_map_io(void) { /* Initialize processor: 20.000 MHz crystal */ at91rm9200_initialize(20000000, AT91RM9200_BGA); - /* Setup the serial ports and console */ - at91_init_serial(&carmeva_uart_config); + /* DBGU on ttyS0. (Rx & Tx only) */ + at91_register_uart(0, 0, 0); + + /* USART1 on ttyS1. (Rx, Tx, CTS, RTS, DTR, DSR, DCD, RI) */ + at91_register_uart(AT91RM9200_ID_US1, 1, ATMEL_UART_CTS | ATMEL_UART_RTS + | ATMEL_UART_DTR | ATMEL_UART_DSR | ATMEL_UART_DCD + | ATMEL_UART_RI); + + /* set serial console to ttyS0 (ie, DBGU) */ + at91_set_serial_console(0); } static void __init carmeva_init_irq(void) diff --git a/arch/arm/mach-at91/board-csb637.c b/arch/arm/mach-at91/board-csb637.c index 419fd19b620..bb1a5474dda 100644 --- a/arch/arm/mach-at91/board-csb637.c +++ b/arch/arm/mach-at91/board-csb637.c @@ -45,10 +45,10 @@ static void __init csb637_map_io(void) /* Initialize processor: 3.6864 MHz crystal */ at91rm9200_initialize(3686400, AT91RM9200_BGA); - /* DBGU on ttyS0 */ + /* DBGU on ttyS0. (Rx & Tx only) */ at91_register_uart(0, 0, 0); - /* make console=ttyS0 the default */ + /* make console=ttyS0 (ie, DBGU) the default */ at91_set_serial_console(0); } diff --git a/arch/arm/mach-at91/board-dk.c b/arch/arm/mach-at91/board-dk.c index c1a813c7169..dab958d2592 100644 --- a/arch/arm/mach-at91/board-dk.c +++ b/arch/arm/mach-at91/board-dk.c @@ -45,17 +45,6 @@ #include "generic.h" -/* - * Serial port configuration. - * 0 .. 3 = USART0 .. USART3 - * 4 = DBGU - */ -static struct at91_uart_config __initdata dk_uart_config = { - .console_tty = 0, /* ttyS0 */ - .nr_tty = 2, - .tty_map = { 4, 1, -1, -1, -1 } /* ttyS0, ..., ttyS4 */ -}; - static void __init dk_map_io(void) { /* Initialize processor: 18.432 MHz crystal */ @@ -64,8 +53,16 @@ static void __init dk_map_io(void) /* Setup the LEDs */ at91_init_leds(AT91_PIN_PB2, AT91_PIN_PB2); - /* Setup the serial ports and console */ - at91_init_serial(&dk_uart_config); + /* DBGU on ttyS0. (Rx & Tx only) */ + at91_register_uart(0, 0, 0); + + /* USART1 on ttyS1. (Rx, Tx, CTS, RTS, DTR, DSR, DCD, RI) */ + at91_register_uart(AT91RM9200_ID_US1, 1, ATMEL_UART_CTS | ATMEL_UART_RTS + | ATMEL_UART_DTR | ATMEL_UART_DSR | ATMEL_UART_DCD + | ATMEL_UART_RI); + + /* set serial console to ttyS0 (ie, DBGU) */ + at91_set_serial_console(0); } static void __init dk_init_irq(void) @@ -163,7 +160,7 @@ static struct at91_nand_data __initdata dk_nand_data = { #define DK_FLASH_SIZE 0x200000 static struct physmap_flash_data dk_flash_data = { - .width = 2, + .width = 2, }; static struct resource dk_flash_resource = { diff --git a/arch/arm/mach-at91/board-eb9200.c b/arch/arm/mach-at91/board-eb9200.c index af1a1d8ecc3..3fe054e0056 100644 --- a/arch/arm/mach-at91/board-eb9200.c +++ b/arch/arm/mach-at91/board-eb9200.c @@ -40,24 +40,24 @@ #include "generic.h" -/* - * Serial port configuration. - * 0 .. 3 = USART0 .. USART3 - * 4 = DBGU - */ -static struct at91_uart_config __initdata eb9200_uart_config = { - .console_tty = 0, /* ttyS0 */ - .nr_tty = 2, - .tty_map = { 4, 1, -1, -1, -1 } /* ttyS0, ..., ttyS4 */ -}; - static void __init eb9200_map_io(void) { /* Initialize processor: 18.432 MHz crystal */ at91rm9200_initialize(18432000, AT91RM9200_BGA); - /* Setup the serial ports and console */ - at91_init_serial(&eb9200_uart_config); + /* DBGU on ttyS0. (Rx & Tx only) */ + at91_register_uart(0, 0, 0); + + /* USART1 on ttyS1. (Rx, Tx, CTS, RTS, DTR, DSR, DCD, RI) */ + at91_register_uart(AT91RM9200_ID_US1, 1, ATMEL_UART_CTS | ATMEL_UART_RTS + | ATMEL_UART_DTR | ATMEL_UART_DSR | ATMEL_UART_DCD + | ATMEL_UART_RI); + + /* USART2 on ttyS2. (Rx, Tx) - IRDA */ + at91_register_uart(AT91RM9200_ID_US2, 2, 0); + + /* set serial console to ttyS0 (ie, DBGU) */ + at91_set_serial_console(0); } static void __init eb9200_init_irq(void) diff --git a/arch/arm/mach-at91/board-ek.c b/arch/arm/mach-at91/board-ek.c index 0574e50a30d..74aa4325eab 100644 --- a/arch/arm/mach-at91/board-ek.c +++ b/arch/arm/mach-at91/board-ek.c @@ -45,17 +45,6 @@ #include "generic.h" -/* - * Serial port configuration. - * 0 .. 3 = USART0 .. USART3 - * 4 = DBGU - */ -static struct at91_uart_config __initdata ek_uart_config = { - .console_tty = 0, /* ttyS0 */ - .nr_tty = 2, - .tty_map = { 4, 1, -1, -1, -1 } /* ttyS0, ..., ttyS4 */ -}; - static void __init ek_map_io(void) { /* Initialize processor: 18.432 MHz crystal */ @@ -64,8 +53,16 @@ static void __init ek_map_io(void) /* Setup the LEDs */ at91_init_leds(AT91_PIN_PB1, AT91_PIN_PB2); - /* Setup the serial ports and console */ - at91_init_serial(&ek_uart_config); + /* DBGU on ttyS0. (Rx & Tx only) */ + at91_register_uart(0, 0, 0); + + /* USART1 on ttyS1. (Rx, Tx, CTS, RTS, DTR, DSR, DCD, RI) */ + at91_register_uart(AT91RM9200_ID_US1, 1, ATMEL_UART_CTS | ATMEL_UART_RTS + | ATMEL_UART_DTR | ATMEL_UART_DSR | ATMEL_UART_DCD + | ATMEL_UART_RI); + + /* set serial console to ttyS0 (ie, DBGU) */ + at91_set_serial_console(0); } static void __init ek_init_irq(void) @@ -122,7 +119,7 @@ static struct i2c_board_info __initdata ek_i2c_devices[] = { #define EK_FLASH_SIZE 0x200000 static struct physmap_flash_data ek_flash_data = { - .width = 2, + .width = 2, }; static struct resource ek_flash_resource = { diff --git a/arch/arm/mach-at91/board-kb9202.c b/arch/arm/mach-at91/board-kb9202.c index 4b39b9cda75..cb065febd95 100644 --- a/arch/arm/mach-at91/board-kb9202.c +++ b/arch/arm/mach-at91/board-kb9202.c @@ -37,19 +37,10 @@ #include <asm/arch/board.h> #include <asm/arch/gpio.h> -#include "generic.h" +#include <asm/arch/at91rm9200_mc.h> +#include "generic.h" -/* - * Serial port configuration. - * 0 .. 3 = USART0 .. USART3 - * 4 = DBGU - */ -static struct at91_uart_config __initdata kb9202_uart_config = { - .console_tty = 0, /* ttyS0 */ - .nr_tty = 3, - .tty_map = { 4, 0, 1, -1, -1 } /* ttyS0, ..., ttyS4 */ -}; static void __init kb9202_map_io(void) { @@ -59,8 +50,20 @@ static void __init kb9202_map_io(void) /* Set up the LEDs */ at91_init_leds(AT91_PIN_PC19, AT91_PIN_PC18); - /* Setup the serial ports and console */ - at91_init_serial(&kb9202_uart_config); + /* DBGU on ttyS0. (Rx & Tx only) */ + at91_register_uart(0, 0, 0); + + /* USART0 on ttyS1 (Rx & Tx only) */ + at91_register_uart(AT91RM9200_ID_US0, 1, 0); + + /* USART1 on ttyS2 (Rx & Tx only) - IRDA (optional) */ + at91_register_uart(AT91RM9200_ID_US1, 2, 0); + + /* USART3 on ttyS3 (Rx, Tx, CTS, RTS) - RS485 (optional) */ + at91_register_uart(AT91RM9200_ID_US3, 3, ATMEL_UART_CTS | ATMEL_UART_RTS); + + /* set serial console to ttyS0 (ie, DBGU) */ + at91_set_serial_console(0); } static void __init kb9202_init_irq(void) diff --git a/arch/arm/mach-at91/board-qil-a9260.c b/arch/arm/mach-at91/board-qil-a9260.c new file mode 100644 index 00000000000..99b4ec3818d --- /dev/null +++ b/arch/arm/mach-at91/board-qil-a9260.c @@ -0,0 +1,255 @@ +/* + * linux/arch/arm/mach-at91/board-qil-a9260.c + * + * Copyright (C) 2005 SAN People + * Copyright (C) 2006 Atmel + * Copyright (C) 2007 Calao-systems + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA + */ + +#include <linux/types.h> +#include <linux/init.h> +#include <linux/mm.h> +#include <linux/module.h> +#include <linux/platform_device.h> +#include <linux/spi/spi.h> +#include <linux/gpio_keys.h> +#include <linux/input.h> +#include <linux/clk.h> + +#include <asm/hardware.h> +#include <asm/setup.h> +#include <asm/mach-types.h> +#include <asm/irq.h> + +#include <asm/mach/arch.h> +#include <asm/mach/map.h> +#include <asm/mach/irq.h> + +#include <asm/arch/board.h> +#include <asm/arch/gpio.h> +#include <asm/arch/at91_shdwc.h> + +#include "generic.h" + + +static void __init ek_map_io(void) +{ + /* Initialize processor: 12.000 MHz crystal */ + at91sam9260_initialize(12000000); + + /* DGBU on ttyS0. (Rx & Tx only) */ + at91_register_uart(0, 0, 0); + + /* USART0 on ttyS1. (Rx, Tx, CTS, RTS, DTR, DSR, DCD, RI) */ + at91_register_uart(AT91SAM9260_ID_US0, 1, ATMEL_UART_CTS | ATMEL_UART_RTS + | ATMEL_UART_DTR | ATMEL_UART_DSR | ATMEL_UART_DCD + | ATMEL_UART_RI); + + /* USART1 on ttyS2. (Rx, Tx, CTS, RTS) */ + at91_register_uart(AT91SAM9260_ID_US1, 2, ATMEL_UART_CTS | ATMEL_UART_RTS); + + /* USART2 on ttyS3. (Rx, Tx, CTS, RTS) */ + at91_register_uart(AT91SAM9260_ID_US2, 3, ATMEL_UART_CTS | ATMEL_UART_RTS); + + /* set serial console to ttyS1 (ie, USART0) */ + at91_set_serial_console(1); + +} + +static void __init ek_init_irq(void) +{ + at91sam9260_init_interrupts(NULL); +} + + +/* + * USB Host port + */ +static struct at91_usbh_data __initdata ek_usbh_data = { + .ports = 2, +}; + +/* + * USB Device port + */ +static struct at91_udc_data __initdata ek_udc_data = { + .vbus_pin = AT91_PIN_PC5, + .pullup_pin = 0, /* pull-up driven by UDC */ +}; + +/* + * SPI devices. + */ +static struct spi_board_info ek_spi_devices[] = { +#if defined(CONFIG_RTC_DRV_M41T94) + { /* M41T94 RTC */ + .modalias = "m41t94", + .chip_select = 0, + .max_speed_hz = 1 * 1000 * 1000, + .bus_num = 0, + } +#endif +}; + +/* + * MACB Ethernet device + */ +static struct at91_eth_data __initdata ek_macb_data = { + .phy_irq_pin = AT91_PIN_PA31, + .is_rmii = 1, +}; + +/* + * NAND flash + */ +static struct mtd_partition __initdata ek_nand_partition[] = { + { + .name = "Uboot & Kernel", + .offset = 0x00000000, + .size = 16 * 1024 * 1024, + }, + { + .name = "Root FS", + .offset = 0x01000000, + .size = 120 * 1024 * 1024, + }, + { + .name = "FS", + .offset = 0x08800000, + .size = 120 * 1024 * 1024, + }, +}; + +static struct mtd_partition * __init nand_partitions(int size, int *num_partitions) +{ + *num_partitions = ARRAY_SIZE(ek_nand_partition); + return ek_nand_partition; +} + +static struct at91_nand_data __initdata ek_nand_data = { + .ale = 21, + .cle = 22, +// .det_pin = ... not connected + .rdy_pin = AT91_PIN_PC13, + .enable_pin = AT91_PIN_PC14, + .partition_info = nand_partitions, +#if defined(CONFIG_MTD_NAND_AT91_BUSWIDTH_16) + .bus_width_16 = 1, +#else + .bus_width_16 = 0, +#endif +}; + +/* + * MCI (SD/MMC) + */ +static struct at91_mmc_data __initdata ek_mmc_data = { + .slot_b = 0, + .wire4 = 1, +// .det_pin = ... not connected +// .wp_pin = ... not connected +// .vcc_pin = ... not connected +}; + +/* + * GPIO Buttons + */ +#if defined(CONFIG_KEYBOARD_GPIO) || defined(CONFIG_KEYBOARD_GPIO_MODULE) +static struct gpio_keys_button ek_buttons[] = { + { /* USER PUSH BUTTON */ + .code = KEY_ENTER, + .gpio = AT91_PIN_PB10, + .active_low = 1, + .desc = "user_pb", + .wakeup = 1, + } +}; + +static struct gpio_keys_platform_data ek_button_data = { + .buttons = ek_buttons, + .nbuttons = ARRAY_SIZE(ek_buttons), +}; + +static struct platform_device ek_button_device = { + .name = "gpio-keys", + .id = -1, + .num_resources = 0, + .dev = { + .platform_data = &ek_button_data, + } +}; + +static void __init ek_add_device_buttons(void) +{ + at91_set_GPIO_periph(AT91_PIN_PB10, 1); /* user push button, pull up enabled */ + at91_set_deglitch(AT91_PIN_PB10, 1); + + platform_device_register(&ek_button_device); +} +#else +static void __init ek_add_device_buttons(void) {} +#endif + +/* + * LEDs + */ +static struct gpio_led ek_leds[] = { + { /* user_led (green) */ + .name = "user_led", + .gpio = AT91_PIN_PB21, + .active_low = 0, + .default_trigger = "heartbeat", + } +}; + +static void __init ek_board_init(void) +{ + /* Serial */ + at91_add_device_serial(); + /* USB Host */ + at91_add_device_usbh(&ek_usbh_data); + /* USB Device */ + at91_add_device_udc(&ek_udc_data); + /* SPI */ + at91_add_device_spi(ek_spi_devices, ARRAY_SIZE(ek_spi_devices)); + /* NAND */ + at91_add_device_nand(&ek_nand_data); + /* I2C */ + at91_add_device_i2c(NULL, 0); + /* Ethernet */ + at91_add_device_eth(&ek_macb_data); + /* MMC */ + at91_add_device_mmc(0, &ek_mmc_data); + /* Push Buttons */ + ek_add_device_buttons(); + /* LEDs */ + at91_gpio_leds(ek_leds, ARRAY_SIZE(ek_leds)); + /* shutdown controller, wakeup button (5 msec low) */ + at91_sys_write(AT91_SHDW_MR, AT91_SHDW_CPTWK0_(10) | AT91_SHDW_WKMODE0_LOW + | AT91_SHDW_RTTWKEN); +} + +MACHINE_START(QIL_A9260, "CALAO QIL_A9260") + /* Maintainer: calao-systems */ + .phys_io = AT91_BASE_SYS, + .io_pg_offst = (AT91_VA_BASE_SYS >> 18) & 0xfffc, + .boot_params = AT91_SDRAM_BASE + 0x100, + .timer = &at91sam926x_timer, + .map_io = ek_map_io, + .init_irq = ek_init_irq, + .init_machine = ek_board_init, +MACHINE_END diff --git a/arch/arm/mach-at91/board-sam9g20ek.c b/arch/arm/mach-at91/board-sam9g20ek.c new file mode 100644 index 00000000000..45617c20124 --- /dev/null +++ b/arch/arm/mach-at91/board-sam9g20ek.c @@ -0,0 +1,218 @@ +/* + * Copyright (C) 2005 SAN People + * Copyright (C) 2008 Atmel + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA + */ + +#include <linux/types.h> +#include <linux/init.h> +#include <linux/mm.h> +#include <linux/module.h> +#include <linux/platform_device.h> +#include <linux/spi/spi.h> +#include <linux/spi/at73c213.h> +#include <linux/clk.h> + +#include <asm/hardware.h> +#include <asm/setup.h> +#include <asm/mach-types.h> +#include <asm/irq.h> + +#include <asm/mach/arch.h> +#include <asm/mach/map.h> +#include <asm/mach/irq.h> + +#include <asm/arch/board.h> +#include <asm/arch/gpio.h> + +#include "generic.h" + + +static void __init ek_map_io(void) +{ + /* Initialize processor: 18.432 MHz crystal */ + at91sam9260_initialize(18432000); + + /* DGBU on ttyS0. (Rx & Tx only) */ + at91_register_uart(0, 0, 0); + + /* USART0 on ttyS1. (Rx, Tx, CTS, RTS, DTR, DSR, DCD, RI) */ + at91_register_uart(AT91SAM9260_ID_US0, 1, ATMEL_UART_CTS | ATMEL_UART_RTS + | ATMEL_UART_DTR | ATMEL_UART_DSR | ATMEL_UART_DCD + | ATMEL_UART_RI); + + /* USART1 on ttyS2. (Rx, Tx, RTS, CTS) */ + at91_register_uart(AT91SAM9260_ID_US1, 2, ATMEL_UART_CTS | ATMEL_UART_RTS); + + /* set serial console to ttyS0 (ie, DBGU) */ + at91_set_serial_console(0); +} + +static void __init ek_init_irq(void) +{ + at91sam9260_init_interrupts(NULL); +} + + +/* + * USB Host port + */ +static struct at91_usbh_data __initdata ek_usbh_data = { + .ports = 2, +}; + +/* + * USB Device port + */ +static struct at91_udc_data __initdata ek_udc_data = { + .vbus_pin = AT91_PIN_PC5, + .pullup_pin = 0, /* pull-up driven by UDC */ +}; + + +/* + * SPI devices. + */ +static struct spi_board_info ek_spi_devices[] = { +#if !defined(CONFIG_MMC_AT91) + { /* DataFlash chip */ + .modalias = "mtd_dataflash", + .chip_select = 1, + .max_speed_hz = 15 * 1000 * 1000, + .bus_num = 0, + }, +#if defined(CONFIG_MTD_AT91_DATAFLASH_CARD) + { /* DataFlash card */ + .modalias = "mtd_dataflash", + .chip_select = 0, + .max_speed_hz = 15 * 1000 * 1000, + .bus_num = 0, + }, +#endif +#endif +}; + + +/* + * MACB Ethernet device + */ +static struct at91_eth_data __initdata ek_macb_data = { + .phy_irq_pin = AT91_PIN_PA7, + .is_rmii = 1, +}; + + +/* + * NAND flash + */ +static struct mtd_partition __initdata ek_nand_partition[] = { + { + .name = "Bootstrap", + .offset = 0, + .size = 4 * 1024 * 1024, + }, + { + .name = "Partition 1", + .offset = 4 * 1024 * 1024, + .size = 60 * 1024 * 1024, + }, + { + .name = "Partition 2", + .offset = 64 * 1024 * 1024, + .size = MTDPART_SIZ_FULL, + }, +}; + +static struct mtd_partition * __init nand_partitions(int size, int *num_partitions) +{ + *num_partitions = ARRAY_SIZE(ek_nand_partition); + return ek_nand_partition; +} + +/* det_pin is not connected */ +static struct at91_nand_data __initdata ek_nand_data = { + .ale = 21, + .cle = 22, + .rdy_pin = AT91_PIN_PC13, + .enable_pin = AT91_PIN_PC14, + .partition_info = nand_partitions, +#if defined(CONFIG_MTD_NAND_AT91_BUSWIDTH_16) + .bus_width_16 = 1, +#else + .bus_width_16 = 0, +#endif +}; + + +/* + * MCI (SD/MMC) + * det_pin, wp_pin and vcc_pin are not connected + */ +static struct at91_mmc_data __initdata ek_mmc_data = { + .slot_b = 1, + .wire4 = 1, +}; + + +/* + * LEDs + */ +static struct gpio_led ek_leds[] = { + { /* "bottom" led, green, userled1 to be defined */ + .name = "ds5", + .gpio = AT91_PIN_PA6, + .active_low = 1, + .default_trigger = "none", + }, + { /* "power" led, yellow */ + .name = "ds1", + .gpio = AT91_PIN_PA9, + .default_trigger = "heartbeat", + } +}; + +static void __init ek_board_init(void) +{ + /* Serial */ + at91_add_device_serial(); + /* USB Host */ + at91_add_device_usbh(&ek_usbh_data); + /* USB Device */ + at91_add_device_udc(&ek_udc_data); + /* SPI */ + at91_add_device_spi(ek_spi_devices, ARRAY_SIZE(ek_spi_devices)); + /* NAND */ + at91_add_device_nand(&ek_nand_data); + /* Ethernet */ + at91_add_device_eth(&ek_macb_data); + /* MMC */ + at91_add_device_mmc(0, &ek_mmc_data); + /* I2C */ + at91_add_device_i2c(NULL, 0); + /* LEDs */ + at91_gpio_leds(ek_leds, ARRAY_SIZE(ek_leds)); +} + +MACHINE_START(AT91SAM9G20EK, "Atmel AT91SAM9G20-EK") + /* Maintainer: Atmel */ + .phys_io = AT91_BASE_SYS, + .io_pg_offst = (AT91_VA_BASE_SYS >> 18) & 0xfffc, + .boot_params = AT91_SDRAM_BASE + 0x100, + .timer = &at91sam926x_timer, + .map_io = ek_map_io, + .init_irq = ek_init_irq, + .init_machine = ek_board_init, +MACHINE_END diff --git a/arch/arm/mach-at91/board-sam9rlek.c b/arch/arm/mach-at91/board-sam9rlek.c index ffc0597aee8..b6a70fc735c 100644 --- a/arch/arm/mach-at91/board-sam9rlek.c +++ b/arch/arm/mach-at91/board-sam9rlek.c @@ -56,6 +56,14 @@ static void __init ek_init_irq(void) /* + * USB HS Device port + */ +static struct usba_platform_data __initdata ek_usba_udc_data = { + .vbus_pin = AT91_PIN_PA8, +}; + + +/* * MCI (SD/MMC) */ static struct at91_mmc_data __initdata ek_mmc_data = { @@ -175,6 +183,8 @@ static void __init ek_board_init(void) { /* Serial */ at91_add_device_serial(); + /* USB HS */ + at91_add_device_usba(&ek_usba_udc_data); /* I2C */ at91_add_device_i2c(NULL, 0); /* NAND */ diff --git a/arch/arm/mach-at91/board-usb-a9260.c b/arch/arm/mach-at91/board-usb-a9260.c new file mode 100644 index 00000000000..837aedf8ffe --- /dev/null +++ b/arch/arm/mach-at91/board-usb-a9260.c @@ -0,0 +1,215 @@ +/* + * linux/arch/arm/mach-at91/board-usb-a9260.c + * + * Copyright (C) 2005 SAN People + * Copyright (C) 2006 Atmel + * Copyright (C) 2007 Calao-systems + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA + */ + +#include <linux/types.h> +#include <linux/init.h> +#include <linux/mm.h> +#include <linux/module.h> +#include <linux/platform_device.h> +#include <linux/spi/spi.h> +#include <linux/gpio_keys.h> +#include <linux/input.h> +#include <linux/clk.h> + +#include <asm/hardware.h> +#include <asm/setup.h> +#include <asm/mach-types.h> +#include <asm/irq.h> + +#include <asm/mach/arch.h> +#include <asm/mach/map.h> +#include <asm/mach/irq.h> + +#include <asm/arch/board.h> +#include <asm/arch/gpio.h> +#include <asm/arch/at91_shdwc.h> + +#include "generic.h" + + +static void __init ek_map_io(void) +{ + /* Initialize processor: 12.000 MHz crystal */ + at91sam9260_initialize(12000000); + + /* DGBU on ttyS0. (Rx & Tx only) */ + at91_register_uart(0, 0, 0); + + /* set serial console to ttyS0 (ie, DBGU) */ + at91_set_serial_console(0); +} + +static void __init ek_init_irq(void) +{ + at91sam9260_init_interrupts(NULL); +} + + +/* + * USB Host port + */ +static struct at91_usbh_data __initdata ek_usbh_data = { + .ports = 2, +}; + +/* + * USB Device port + */ +static struct at91_udc_data __initdata ek_udc_data = { + .vbus_pin = AT91_PIN_PC5, + .pullup_pin = 0, /* pull-up driven by UDC */ +}; + +/* + * MACB Ethernet device + */ +static struct at91_eth_data __initdata ek_macb_data = { + .phy_irq_pin = AT91_PIN_PA31, + .is_rmii = 1, +}; + +/* + * NAND flash + */ +static struct mtd_partition __initdata ek_nand_partition[] = { + { + .name = "Uboot & Kernel", + .offset = 0x00000000, + .size = 16 * 1024 * 1024, + }, + { + .name = "Root FS", + .offset = 0x01000000, + .size = 120 * 1024 * 1024, + }, + { + .name = "FS", + .offset = 0x08800000, + .size = 120 * 1024 * 1024, + } +}; + +static struct mtd_partition * __init nand_partitions(int size, int *num_partitions) +{ + *num_partitions = ARRAY_SIZE(ek_nand_partition); + return ek_nand_partition; +} + +static struct at91_nand_data __initdata ek_nand_data = { + .ale = 21, + .cle = 22, +// .det_pin = ... not connected + .rdy_pin = AT91_PIN_PC13, + .enable_pin = AT91_PIN_PC14, + .partition_info = nand_partitions, +#if defined(CONFIG_MTD_NAND_AT91_BUSWIDTH_16) + .bus_width_16 = 1, +#else + .bus_width_16 = 0, +#endif +}; + +/* + * GPIO Buttons + */ + +#if defined(CONFIG_KEYBOARD_GPIO) || defined(CONFIG_KEYBOARD_GPIO_MODULE) +static struct gpio_keys_button ek_buttons[] = { + { /* USER PUSH BUTTON */ + .code = KEY_ENTER, + .gpio = AT91_PIN_PB10, + .active_low = 1, + .desc = "user_pb", + .wakeup = 1, + } +}; + +static struct gpio_keys_platform_data ek_button_data = { + .buttons = ek_buttons, + .nbuttons = ARRAY_SIZE(ek_buttons), +}; + +static struct platform_device ek_button_device = { + .name = "gpio-keys", + .id = -1, + .num_resources = 0, + .dev = { + .platform_data = &ek_button_data, + } +}; + +static void __init ek_add_device_buttons(void) +{ + at91_set_GPIO_periph(AT91_PIN_PB10, 1); /* user push button, pull up enabled */ + at91_set_deglitch(AT91_PIN_PB10, 1); + + platform_device_register(&ek_button_device); +} +#else +static void __init ek_add_device_buttons(void) {} +#endif + +/* + * LEDs + */ +static struct gpio_led ek_leds[] = { + { /* user_led (green) */ + .name = "user_led", + .gpio = AT91_PIN_PB21, + .active_low = 0, + .default_trigger = "heartbeat", + } +}; + +static void __init ek_board_init(void) +{ + /* Serial */ + at91_add_device_serial(); + /* USB Host */ + at91_add_device_usbh(&ek_usbh_data); + /* USB Device */ + at91_add_device_udc(&ek_udc_data); + /* NAND */ + at91_add_device_nand(&ek_nand_data); + /* I2C */ + at91_add_device_i2c(NULL, 0); + /* Ethernet */ + at91_add_device_eth(&ek_macb_data); + /* Push Buttons */ + ek_add_device_buttons(); + /* LEDs */ + at91_gpio_leds(ek_leds, ARRAY_SIZE(ek_leds)); + /* shutdown controller, wakeup button (5 msec low) */ + at91_sys_write(AT91_SHDW_MR, AT91_SHDW_CPTWK0_(10) | AT91_SHDW_WKMODE0_LOW + | AT91_SHDW_RTTWKEN); +} + +MACHINE_START(USB_A9260, "CALAO USB_A9260") + /* Maintainer: calao-systems */ + .phys_io = AT91_BASE_SYS, + .io_pg_offst = (AT91_VA_BASE_SYS >> 18) & 0xfffc, + .boot_params = AT91_SDRAM_BASE + 0x100, + .timer = &at91sam926x_timer, + .map_io = ek_map_io, + .init_irq = ek_init_irq, + .init_machine = ek_board_init, +MACHINE_END diff --git a/arch/arm/mach-at91/board-usb-a9263.c b/arch/arm/mach-at91/board-usb-a9263.c new file mode 100644 index 00000000000..95800d32bd4 --- /dev/null +++ b/arch/arm/mach-at91/board-usb-a9263.c @@ -0,0 +1,230 @@ +/* + * linux/arch/arm/mach-at91/board-usb-a9263.c + * + * Copyright (C) 2005 SAN People + * Copyright (C) 2007 Atmel Corporation. + * Copyright (C) 2007 Calao-systems + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA + */ + +#include <linux/types.h> +#include <linux/init.h> +#include <linux/mm.h> +#include <linux/module.h> +#include <linux/platform_device.h> +#include <linux/spi/spi.h> +#include <linux/gpio_keys.h> +#include <linux/input.h> + +#include <asm/hardware.h> +#include <asm/setup.h> +#include <asm/mach-types.h> +#include <asm/irq.h> + +#include <asm/mach/arch.h> +#include <asm/mach/map.h> +#include <asm/mach/irq.h> + +#include <asm/arch/board.h> +#include <asm/arch/gpio.h> +#include <asm/arch/at91_shdwc.h> + +#include "generic.h" + + +static void __init ek_map_io(void) +{ + /* Initialize processor: 12.00 MHz crystal */ + at91sam9263_initialize(12000000); + + /* DGBU on ttyS0. (Rx & Tx only) */ + at91_register_uart(0, 0, 0); + + /* set serial console to ttyS0 (ie, DBGU) */ + at91_set_serial_console(0); +} + +static void __init ek_init_irq(void) +{ + at91sam9263_init_interrupts(NULL); +} + + +/* + * USB Host port + */ +static struct at91_usbh_data __initdata ek_usbh_data = { + .ports = 2, +}; + +/* + * USB Device port + */ +static struct at91_udc_data __initdata ek_udc_data = { + .vbus_pin = AT91_PIN_PB11, + .pullup_pin = 0, /* pull-up driven by UDC */ +}; + +/* + * SPI devices. + */ +static struct spi_board_info ek_spi_devices[] = { +#if !defined(CONFIG_MMC_AT91) + { /* DataFlash chip */ + .modalias = "mtd_dataflash", + .chip_select = 0, + .max_speed_hz = 15 * 1000 * 1000, + .bus_num = 0, + } +#endif +}; + +/* + * MACB Ethernet device + */ +static struct at91_eth_data __initdata ek_macb_data = { + .phy_irq_pin = AT91_PIN_PE31, + .is_rmii = 1, +}; + +/* + * NAND flash + */ +static struct mtd_partition __initdata ek_nand_partition[] = { + { + .name = "Linux Kernel", + .offset = 0x00000000, + .size = 16 * 1024 * 1024, + }, + { + .name = "Root FS", + .offset = 0x01000000, + .size = 120 * 1024 * 1024, + }, + { + .name = "FS", + .offset = 0x08800000, + .size = 120 * 1024 * 1024, + } +}; + +static struct mtd_partition * __init nand_partitions(int size, int *num_partitions) +{ + *num_partitions = ARRAY_SIZE(ek_nand_partition); + return ek_nand_partition; +} + +static struct at91_nand_data __initdata ek_nand_data = { + .ale = 21, + .cle = 22, +// .det_pin = ... not connected + .rdy_pin = AT91_PIN_PA22, + .enable_pin = AT91_PIN_PD15, + .partition_info = nand_partitions, +#if defined(CONFIG_MTD_NAND_AT91_BUSWIDTH_16) + .bus_width_16 = 1, +#else + .bus_width_16 = 0, +#endif +}; + +/* + * GPIO Buttons + */ +#if defined(CONFIG_KEYBOARD_GPIO) || defined(CONFIG_KEYBOARD_GPIO_MODULE) +static struct gpio_keys_button ek_buttons[] = { + { /* USER PUSH BUTTON */ + .code = KEY_ENTER, + .gpio = AT91_PIN_PB10, + .active_low = 1, + .desc = "user_pb", + .wakeup = 1, + } +}; + +static struct gpio_keys_platform_data ek_button_data = { + .buttons = ek_buttons, + .nbuttons = ARRAY_SIZE(ek_buttons), +}; + +static struct platform_device ek_button_device = { + .name = "gpio-keys", + .id = -1, + .num_resources = 0, + .dev = { + .platform_data = &ek_button_data, + } +}; + +static void __init ek_add_device_buttons(void) +{ + at91_set_GPIO_periph(AT91_PIN_PB10, 1); /* user push button, pull up enabled */ + at91_set_deglitch(AT91_PIN_PB10, 1); + + platform_device_register(&ek_button_device); +} +#else +static void __init ek_add_device_buttons(void) {} +#endif + +/* + * LEDs + */ +static struct gpio_led ek_leds[] = { + { /* user_led (green) */ + .name = "user_led", + .gpio = AT91_PIN_PB21, + .active_low = 1, + .default_trigger = "heartbeat", + } +}; + + +static void __init ek_board_init(void) +{ + /* Serial */ + at91_add_device_serial(); + /* USB Host */ + at91_add_device_usbh(&ek_usbh_data); + /* USB Device */ + at91_add_device_udc(&ek_udc_data); + /* SPI */ + at91_add_device_spi(ek_spi_devices, ARRAY_SIZE(ek_spi_devices)); + /* Ethernet */ + at91_add_device_eth(&ek_macb_data); + /* NAND */ + at91_add_device_nand(&ek_nand_data); + /* I2C */ + at91_add_device_i2c(NULL, 0); + /* Push Buttons */ + ek_add_device_buttons(); + /* LEDs */ + at91_gpio_leds(ek_leds, ARRAY_SIZE(ek_leds)); + /* shutdown controller, wakeup button (5 msec low) */ + at91_sys_write(AT91_SHDW_MR, AT91_SHDW_CPTWK0_(10) | AT91_SHDW_WKMODE0_LOW + | AT91_SHDW_RTTWKEN); +} + +MACHINE_START(USB_A9263, "CALAO USB_A9263") + /* Maintainer: calao-systems */ + .phys_io = AT91_BASE_SYS, + .io_pg_offst = (AT91_VA_BASE_SYS >> 18) & 0xfffc, + .boot_params = AT91_SDRAM_BASE + 0x100, + .timer = &at91sam926x_timer, + .map_io = ek_map_io, + .init_irq = ek_init_irq, + .init_machine = ek_board_init, +MACHINE_END diff --git a/arch/arm/mach-at91/board-yl-9200.c b/arch/arm/mach-at91/board-yl-9200.c index b5717108991..7079050ab88 100755 --- a/arch/arm/mach-at91/board-yl-9200.c +++ b/arch/arm/mach-at91/board-yl-9200.c @@ -1,11 +1,10 @@ /* * linux/arch/arm/mach-at91/board-yl-9200.c * - * Adapted from: - *various board files in - * /arch/arm/mach-at91 - * modifications to convert to YL-9200 platform - * Copyright (C) 2007 S.Birtles + * Adapted from various board files in arch/arm/mach-at91 + * + * Modifications for YL-9200 platform: + * Copyright (C) 2007 S. Birtles * * This program is free software; you can redistribute it and/or modify * it under the terms of the GNU General Public License as published by @@ -26,13 +25,14 @@ #include <linux/init.h> #include <linux/mm.h> #include <linux/module.h> +#include <linux/dma-mapping.h> #include <linux/platform_device.h> #include <linux/spi/spi.h> -/*#include <linux/can_bus/candata.h>*/ #include <linux/spi/ads7846.h> #include <linux/mtd/physmap.h> +#include <linux/gpio_keys.h> +#include <linux/input.h> -/*#include <sound/gpio_sounder.h>*/ #include <asm/hardware.h> #include <asm/setup.h> #include <asm/mach-types.h> @@ -45,179 +45,108 @@ #include <asm/arch/board.h> #include <asm/arch/gpio.h> #include <asm/arch/at91rm9200_mc.h> -#include <linux/gpio_keys.h> -#include <linux/input.h> #include "generic.h" -#include <asm/arch/at91_pio.h> -#define YL_9200_FLASH_BASE AT91_CHIPSELECT_0 -#define YL_9200_FLASH_SIZE 0x800000 -/* - * Serial port configuration. - * 0 .. 3 = USART0 .. USART3 - * 4 = DBGU - *atmel_usart.0: ttyS0 at MMIO 0xfefff200 (irq = 1) is a ATMEL_SERIAL - *atmel_usart.1: ttyS1 at MMIO 0xfffc0000 (irq = 6) is a ATMEL_SERIAL - *atmel_usart.2: ttyS2 at MMIO 0xfffc4000 (irq = 7) is a ATMEL_SERIAL - *atmel_usart.3: ttyS3 at MMIO 0xfffc8000 (irq = 8) is a ATMEL_SERIAL - *atmel_usart.4: ttyS4 at MMIO 0xfffcc000 (irq = 9) is a ATMEL_SERIAL - * on the YL-9200 we are sitting at the following - *ttyS0 at MMIO 0xfefff200 (irq = 1) is a AT91_SERIAL - *ttyS1 at MMIO 0xfefc4000 (irq = 7) is a AT91_SERIAL - */ +static void __init yl9200_map_io(void) +{ + /* Initialize processor: 18.432 MHz crystal */ + at91rm9200_initialize(18432000, AT91RM9200_PQFP); -/* extern void __init yl_9200_add_device_sounder(struct gpio_sounder *sounders, int nr);*/ + /* Setup the LEDs D2=PB17 (timer), D3=PB16 (cpu) */ + at91_init_leds(AT91_PIN_PB16, AT91_PIN_PB17); -static struct at91_uart_config __initdata yl_9200_uart_config = { - .console_tty = 0, /* ttyS0 */ - .nr_tty = 3, - .tty_map = { 4, 1, 0, -1, -1 } /* ttyS0, ..., ttyS4 */ -}; + /* DBGU on ttyS0. (Rx & Tx only) */ + at91_register_uart(0, 0, 0); -static void __init yl_9200_map_io(void) -{ - /* Initialize processor: 18.432 MHz crystal */ - /*Also initialises register clocks & gpio*/ - at91rm9200_initialize(18432000, AT91RM9200_PQFP); /*we have a 3 bank system*/ + /* USART1 on ttyS1. (Rx, Tx, CTS, RTS, DTR, DSR, DCD, RI) */ + at91_register_uart(AT91RM9200_ID_US1, 1, ATMEL_UART_CTS | ATMEL_UART_RTS + | ATMEL_UART_DTR | ATMEL_UART_DSR | ATMEL_UART_DCD + | ATMEL_UART_RI); - /* Setup the serial ports and console */ - at91_init_serial(&yl_9200_uart_config); + /* USART0 on ttyS2. (Rx & Tx only to JP3) */ + at91_register_uart(AT91RM9200_ID_US0, 2, 0); - /* Setup the LEDs D2=PB17,D3=PB16 */ - at91_init_leds(AT91_PIN_PB16,AT91_PIN_PB17); /*cpu-led,timer-led*/ + /* USART3 on ttyS3. (Rx, Tx, RTS - RS485 interface) */ + at91_register_uart(AT91RM9200_ID_US3, 3, ATMEL_UART_RTS); + + /* set serial console to ttyS0 (ie, DBGU) */ + at91_set_serial_console(0); } -static void __init yl_9200_init_irq(void) +static void __init yl9200_init_irq(void) { at91rm9200_init_interrupts(NULL); } -static struct at91_eth_data __initdata yl_9200_eth_data = { - .phy_irq_pin = AT91_PIN_PB28, - .is_rmii = 1, -}; -static struct at91_usbh_data __initdata yl_9200_usbh_data = { - .ports = 1, /* this should be 1 not 2 for the Yl9200*/ +/* + * LEDs + */ +static struct gpio_led yl9200_leds[] = { + { /* D2 */ + .name = "led2", + .gpio = AT91_PIN_PB17, + .active_low = 1, + .default_trigger = "timer", + }, + { /* D3 */ + .name = "led3", + .gpio = AT91_PIN_PB16, + .active_low = 1, + .default_trigger = "heartbeat", + }, + { /* D4 */ + .name = "led4", + .gpio = AT91_PIN_PB15, + .active_low = 1, + }, + { /* D5 */ + .name = "led5", + .gpio = AT91_PIN_PB8, + .active_low = 1, + } }; -static struct at91_udc_data __initdata yl_9200_udc_data = { -/*on sheet 7 Schemitic rev 1.0*/ - .pullup_pin = AT91_PIN_PC4, - .vbus_pin= AT91_PIN_PC5, - .pullup_active_low = 1, /*ACTIVE LOW!! due to PNP transistor on page 7*/ - -}; /* -static struct at91_cf_data __initdata yl_9200_cf_data = { -TODO S.BIRTLES - .det_pin = AT91_PIN_xxx, - .rst_pin = AT91_PIN_xxx, - .irq_pin = ... not connected - .vcc_pin = ... always powered - + * Ethernet + */ +static struct at91_eth_data __initdata yl9200_eth_data = { + .phy_irq_pin = AT91_PIN_PB28, + .is_rmii = 1, }; -*/ -static struct at91_mmc_data __initdata yl_9200_mmc_data = { - .det_pin = AT91_PIN_PB9, /*THIS LOOKS CORRECT SHEET7*/ -/* .wp_pin = ... not connected SHEET7*/ - .slot_b = 0, - .wire4 = 1, +/* + * USB Host + */ +static struct at91_usbh_data __initdata yl9200_usbh_data = { + .ports = 1, /* PQFP version of AT91RM9200 */ }; -/* -------------------------------------------------------------------- - * Touch screen - * -------------------------------------------------------------------- */ -#if defined(CONFIG_TOUCHSCREEN_ADS7846) || defined(CONFIG_TOUCHSCREEN_ADS7846_MODULE) -static int ads7843_pendown_state(void) -{ - return !at91_get_gpio_value(AT91_PIN_PB11); /* Touchscreen PENIRQ */ -} - -static void __init at91_init_device_ts(void) -{ -/*IMPORTANT NOTE THE SPI INTERFACE IS ALREADY CONFIGURED BY XXX_DEVICES.C -THAT IS TO SAY THAT MISO,MOSI,SPCK AND CS are already configured -we only need to enable the other datapins which are: -PB10/RK1 BUSY -*/ -/* Touchscreen BUSY signal , pin,use pullup ( TODO not currently used in the ADS7843/6.c driver)*/ -at91_set_gpio_input(AT91_PIN_PB10, 1); -} - -#else -static void __init at91_init_device_ts(void) {} -#endif - -static struct ads7846_platform_data ads_info = { - .model = 7843, - .x_min = 150, - .x_max = 3830, - .y_min = 190, - .y_max = 3830, - .vref_delay_usecs = 100, -/* for a 8" touch screen*/ - //.x_plate_ohms = 603, //= 450, S.Birtles TODO - //.y_plate_ohms = 332, //= 250, S.Birtles TODO -/*for a 10.4" touch screen*/ - //.x_plate_ohms =611, - //.y_plate_ohms =325, - - .x_plate_ohms = 576, - .y_plate_ohms = 366, - // - .pressure_max = 15000, /*generally nonsense on the 7843*/ - /*number of times to send query to chip in a given run 0 equals one time (do not set to 0!! ,there is a bug in ADS 7846 code)*/ - .debounce_max = 1, - .debounce_rep = 0, - .debounce_tol = (~0), - .get_pendown_state = ads7843_pendown_state, -}; +/* + * USB Device + */ +static struct at91_udc_data __initdata yl9200_udc_data = { + .pullup_pin = AT91_PIN_PC4, + .vbus_pin = AT91_PIN_PC5, + .pullup_active_low = 1, /* Active Low due to PNP transistor (pg 7) */ -/*static struct canbus_platform_data can_info = { - .model = 2510, }; -*/ - -static struct spi_board_info yl_9200_spi_devices[] = { -/*this sticks it at: - /sys/devices/platform/atmel_spi.0/spi0.0 - /sys/bus/platform/devices/ -Documentation/spi IIRC*/ -#if defined(CONFIG_TOUCHSCREEN_ADS7846) || defined(CONFIG_TOUCHSCREEN_ADS7846_MODULE) - /*(this IS correct 04-NOV-2007)*/ - { - .modalias = "ads7846", /* because the driver is called ads7846*/ - .chip_select = 0, /*THIS MUST BE AN INDEX INTO AN ARRAY OF pins */ -/*this is ONLY TO BE USED if chipselect above is not used, it passes a pin directly for the chip select*/ - /*.controller_data =AT91_PIN_PA3 ,*/ - .max_speed_hz = 5000*26, /*(4700 * 26)-125000 * 26, (max sample rate @ 3V) * (cmd + data + overhead) */ - .bus_num = 0, - .platform_data = &ads_info, - .irq = AT91_PIN_PB11, - }, -#endif -/*we need to put our CAN driver data here!!*/ -/*THIS IS ALL DUMMY DATA*/ -/* { - .modalias = "mcp2510", //DUMMY for MCP2510 chip - .chip_select = 1,*/ /*THIS MUST BE AN INDEX INTO AN ARRAY OF pins */ - /*this is ONLY TO BE USED if chipselect above is not used, it passes a pin directly for the chip select */ - /* .controller_data =AT91_PIN_PA4 , - .max_speed_hz = 25000 * 26, - .bus_num = 0, - .platform_data = &can_info, - .irq = AT91_PIN_PC0, - }, - */ - //max SPI chip needs to go here +/* + * MMC + */ +static struct at91_mmc_data __initdata yl9200_mmc_data = { + .det_pin = AT91_PIN_PB9, + // .wp_pin = ... not connected + .wire4 = 1, }; -static struct mtd_partition __initdata yl_9200_nand_partition[] = { +/* + * NAND Flash + */ +static struct mtd_partition __initdata yl9200_nand_partition[] = { { .name = "AT91 NAND partition 1, boot", .offset = 0, @@ -242,442 +171,434 @@ static struct mtd_partition __initdata yl_9200_nand_partition[] = { .name = "AT91 NAND partition 5, ext-fs", .offset = 32 * SZ_1M, .size = 32 * SZ_1M - }, + } }; static struct mtd_partition * __init nand_partitions(int size, int *num_partitions) { - *num_partitions = ARRAY_SIZE(yl_9200_nand_partition); - return yl_9200_nand_partition; + *num_partitions = ARRAY_SIZE(yl9200_nand_partition); + return yl9200_nand_partition; } -static struct at91_nand_data __initdata yl_9200_nand_data = { - .ale= 6, - .cle= 7, - /*.det_pin = AT91_PIN_PCxx,*/ /*we don't have a det pin because NandFlash is fixed to board*/ - .rdy_pin = AT91_PIN_PC14, /*R/!B Sheet10*/ - .enable_pin = AT91_PIN_PC15, /*!CE Sheet10 */ +static struct at91_nand_data __initdata yl9200_nand_data = { + .ale = 6, + .cle = 7, + // .det_pin = ... not connected + .rdy_pin = AT91_PIN_PC14, /* R/!B (Sheet10) */ + .enable_pin = AT91_PIN_PC15, /* !CE (Sheet10) */ .partition_info = nand_partitions, }; - - /* -TODO S.Birtles -potentially a problem with the size above -physmap platform flash device: 00800000 at 10000000 -physmap-flash.0: Found 1 x16 devices at 0x0 in 16-bit bank -NOR chip too large to fit in mapping. Attempting to cope... - Intel/Sharp Extended Query Table at 0x0031 -Using buffer write method -cfi_cmdset_0001: Erase suspend on write enabled -Reducing visibility of 16384KiB chip to 8192KiB -*/ + * NOR Flash + */ +#define YL9200_FLASH_BASE AT91_CHIPSELECT_0 +#define YL9200_FLASH_SIZE 0x1000000 -static struct mtd_partition yl_9200_flash_partitions[] = { +static struct mtd_partition yl9200_flash_partitions[] = { + { + .name = "Bootloader", + .size = 0x00040000, + .offset = 0, + .mask_flags = MTD_WRITEABLE, /* force read-only */ + }, { - .name = "Bootloader", - .size = 0x00040000, - .offset = 0, - .mask_flags = MTD_WRITEABLE /* force read-only */ - },{ - .name = "Kernel", - .size = 0x001C0000, - .offset = 0x00040000, - },{ - .name = "Filesystem", - .size = MTDPART_SIZ_FULL, - .offset = 0x00200000 + .name = "Kernel", + .size = 0x001C0000, + .offset = 0x00040000, + }, + { + .name = "Filesystem", + .size = MTDPART_SIZ_FULL, + .offset = 0x00200000 } - }; -static struct physmap_flash_data yl_9200_flash_data = { - .width = 2, - .parts = yl_9200_flash_partitions, - .nr_parts = ARRAY_SIZE(yl_9200_flash_partitions), +static struct physmap_flash_data yl9200_flash_data = { + .width = 2, + .parts = yl9200_flash_partitions, + .nr_parts = ARRAY_SIZE(yl9200_flash_partitions), }; -static struct resource yl_9200_flash_resources[] = { -{ - .start = YL_9200_FLASH_BASE, - .end = YL_9200_FLASH_BASE + YL_9200_FLASH_SIZE - 1, - .flags = IORESOURCE_MEM, +static struct resource yl9200_flash_resources[] = { + { + .start = YL9200_FLASH_BASE, + .end = YL9200_FLASH_BASE + YL9200_FLASH_SIZE - 1, + .flags = IORESOURCE_MEM, } }; -static struct platform_device yl_9200_flash = { +static struct platform_device yl9200_flash = { .name = "physmap-flash", .id = 0, .dev = { - .platform_data = &yl_9200_flash_data, + .platform_data = &yl9200_flash_data, }, - .resource = yl_9200_flash_resources, - .num_resources = ARRAY_SIZE(yl_9200_flash_resources), + .resource = yl9200_flash_resources, + .num_resources = ARRAY_SIZE(yl9200_flash_resources), }; - -static struct gpio_led yl_9200_leds[] = { -/*D2 &D3 are passed directly in via at91_init_leds*/ - { - .name = "led4", /*D4*/ - .gpio = AT91_PIN_PB15, - .active_low = 1, - .default_trigger = "heartbeat", - /*.default_trigger = "timer",*/ - }, - { - .name = "led5", /*D5*/ - .gpio = AT91_PIN_PB8, - .active_low = 1, - .default_trigger = "heartbeat", - } -}; - -//static struct gpio_sounder yl_9200_sounder[] = {*/ -/*This is a simple speaker attached to a gpo line*/ - -// { -// .name = "Speaker", /*LS1*/ -// .gpio = AT91_PIN_PA22, -// .active_low = 0, -// .default_trigger = "heartbeat", - /*.default_trigger = "timer",*/ -// }, -//}; - - - -static struct i2c_board_info __initdata yl_9200_i2c_devices[] = { - { - /*TODO*/ - I2C_BOARD_INFO("CS4334", 0x00), +/* + * I2C (TWI) + */ +static struct i2c_board_info __initdata yl9200_i2c_devices[] = { + { /* EEPROM */ + I2C_BOARD_INFO("24c128", 0x50), } }; - - /* +/* * GPIO Buttons - */ +*/ #if defined(CONFIG_KEYBOARD_GPIO) || defined(CONFIG_KEYBOARD_GPIO_MODULE) -static struct gpio_keys_button yl_9200_buttons[] = { +static struct gpio_keys_button yl9200_buttons[] = { { .gpio = AT91_PIN_PA24, - .code = BTN_2, + .code = BTN_2, .desc = "SW2", .active_low = 1, .wakeup = 1, }, { .gpio = AT91_PIN_PB1, - .code = BTN_3, + .code = BTN_3, .desc = "SW3", .active_low = 1, .wakeup = 1, }, { .gpio = AT91_PIN_PB2, - .code = BTN_4, + .code = BTN_4, .desc = "SW4", .active_low = 1, .wakeup = 1, }, { .gpio = AT91_PIN_PB6, - .code = BTN_5, + .code = BTN_5, .desc = "SW5", .active_low = 1, .wakeup = 1, - }, - + } }; -static struct gpio_keys_platform_data yl_9200_button_data = { - .buttons = yl_9200_buttons, - .nbuttons = ARRAY_SIZE(yl_9200_buttons), +static struct gpio_keys_platform_data yl9200_button_data = { + .buttons = yl9200_buttons, + .nbuttons = ARRAY_SIZE(yl9200_buttons), }; -static struct platform_device yl_9200_button_device = { +static struct platform_device yl9200_button_device = { .name = "gpio-keys", .id = -1, .num_resources = 0, .dev = { - .platform_data = &yl_9200_button_data, + .platform_data = &yl9200_button_data, } }; -static void __init yl_9200_add_device_buttons(void) +static void __init yl9200_add_device_buttons(void) { - //SW2 - at91_set_gpio_input(AT91_PIN_PA24, 0); + at91_set_gpio_input(AT91_PIN_PA24, 1); /* SW2 */ at91_set_deglitch(AT91_PIN_PA24, 1); - - //SW3 - at91_set_gpio_input(AT91_PIN_PB1, 0); + at91_set_gpio_input(AT91_PIN_PB1, 1); /* SW3 */ at91_set_deglitch(AT91_PIN_PB1, 1); - //SW4 - at91_set_gpio_input(AT91_PIN_PB2, 0); + at91_set_gpio_input(AT91_PIN_PB2, 1); /* SW4 */ at91_set_deglitch(AT91_PIN_PB2, 1); - - //SW5 - at91_set_gpio_input(AT91_PIN_PB6, 0); + at91_set_gpio_input(AT91_PIN_PB6, 1); /* SW5 */ at91_set_deglitch(AT91_PIN_PB6, 1); + /* Enable buttons (Sheet 5) */ + at91_set_gpio_output(AT91_PIN_PB7, 1); + + platform_device_register(&yl9200_button_device); +} +#else +static void __init yl9200_add_device_buttons(void) {} +#endif + +/* + * Touchscreen + */ +#if defined(CONFIG_TOUCHSCREEN_ADS7846) || defined(CONFIG_TOUCHSCREEN_ADS7846_MODULE) +static int ads7843_pendown_state(void) +{ + return !at91_get_gpio_value(AT91_PIN_PB11); /* Touchscreen PENIRQ */ +} + +static struct ads7846_platform_data ads_info = { + .model = 7843, + .x_min = 150, + .x_max = 3830, + .y_min = 190, + .y_max = 3830, + .vref_delay_usecs = 100, + + /* For a 8" touch-screen */ + // .x_plate_ohms = 603, + // .y_plate_ohms = 332, + + /* For a 10.4" touch-screen */ + // .x_plate_ohms = 611, + // .y_plate_ohms = 325, + + .x_plate_ohms = 576, + .y_plate_ohms = 366, + + .pressure_max = 15000, /* generally nonsense on the 7843 */ + .debounce_max = 1, + .debounce_rep = 0, + .debounce_tol = (~0), + .get_pendown_state = ads7843_pendown_state, +}; - at91_set_gpio_output(AT91_PIN_PB7, 1); /* #TURN BUTTONS ON, SHEET 5 of schematics */ - platform_device_register(&yl_9200_button_device); +static void __init yl9200_add_device_ts(void) +{ + at91_set_gpio_input(AT91_PIN_PB11, 1); /* Touchscreen interrupt pin */ + at91_set_gpio_input(AT91_PIN_PB10, 1); /* Touchscreen BUSY signal - not used! */ } #else -static void __init yl_9200_add_device_buttons(void) {} +static void __init yl9200_add_device_ts(void) {} +#endif + +/* + * SPI devices + */ +static struct spi_board_info yl9200_spi_devices[] = { +#if defined(CONFIG_TOUCHSCREEN_ADS7846) || defined(CONFIG_TOUCHSCREEN_ADS7846_MODULE) + { /* Touchscreen */ + .modalias = "ads7846", + .chip_select = 0, + .max_speed_hz = 5000 * 26, + .platform_data = &ads_info, + .irq = AT91_PIN_PB11, + }, #endif + { /* CAN */ + .modalias = "mcp2510", + .chip_select = 1, + .max_speed_hz = 25000 * 26, + .irq = AT91_PIN_PC0, + } +}; +/* + * LCD / VGA + * + * EPSON S1D13806 FB (discontinued chip) + * EPSON S1D13506 FB + */ #if defined(CONFIG_FB_S1D135XX) || defined(CONFIG_FB_S1D13XXX_MODULE) #include <video/s1d13xxxfb.h> -/* EPSON S1D13806 FB (discontinued chip)*/ -/* EPSON S1D13506 FB */ - #define AT91_FB_REG_BASE 0x80000000L #define AT91_FB_REG_SIZE 0x200 #define AT91_FB_VMEM_BASE 0x80200000L #define AT91_FB_VMEM_SIZE 0x200000L -/*#define S1D_DISPLAY_WIDTH 640*/ -/*#define S1D_DISPLAY_HEIGHT 480*/ - - -static void __init yl_9200_init_video(void) +static void __init yl9200_init_video(void) { - at91_sys_write(AT91_PIOC + PIO_ASR,AT91_PIN_PC6); - at91_sys_write(AT91_PIOC + PIO_BSR,0); - at91_sys_write(AT91_PIOC + PIO_ASR,AT91_PIN_PC6); - - at91_sys_write( AT91_SMC_CSR(2), - AT91_SMC_NWS_(0x4) | - AT91_SMC_WSEN | - AT91_SMC_TDF_(0x100) | - AT91_SMC_DBW - ); - - + /* NWAIT Signal */ + at91_set_A_periph(AT91_PIN_PC6, 0); + /* Initialization of the Static Memory Controller for Chip Select 2 */ + at91_sys_write(AT91_SMC_CSR(2), AT91_SMC_DBW_16 /* 16 bit */ + | AT91_SMC_WSEN | AT91_SMC_NWS_(0x4) /* wait states */ + | AT91_SMC_TDF_(0x100) /* float time */ + ); } - -static struct s1d13xxxfb_regval yl_9200_s1dfb_initregs[] = +static struct s1d13xxxfb_regval yl9200_s1dfb_initregs[] = { - {S1DREG_MISC, 0x00}, /* Miscellaneous Register*/ - {S1DREG_COM_DISP_MODE, 0x01}, /* Display Mode Register, LCD only*/ - {S1DREG_GPIO_CNF0, 0x00}, /* General IO Pins Configuration Register*/ - {S1DREG_GPIO_CTL0, 0x00}, /* General IO Pins Control Register*/ - {S1DREG_CLK_CNF, 0x11}, /* Memory Clock Configuration Register*/ - {S1DREG_LCD_CLK_CNF, 0x10}, /* LCD Pixel Clock Configuration Register*/ - {S1DREG_CRT_CLK_CNF, 0x12}, /* CRT/TV Pixel Clock Configuration Register*/ - {S1DREG_MPLUG_CLK_CNF, 0x01}, /* MediaPlug Clock Configuration Register*/ - {S1DREG_CPU2MEM_WST_SEL, 0x02}, /* CPU To Memory Wait State Select Register*/ - {S1DREG_MEM_CNF, 0x00}, /* Memory Configuration Register*/ - {S1DREG_SDRAM_REF_RATE, 0x04}, /* DRAM Refresh Rate Register, MCLK source*/ - {S1DREG_SDRAM_TC0, 0x12}, /* DRAM Timings Control Register 0*/ - {S1DREG_SDRAM_TC1, 0x02}, /* DRAM Timings Control Register 1*/ - {S1DREG_PANEL_TYPE, 0x25}, /* Panel Type Register*/ - {S1DREG_MOD_RATE, 0x00}, /* MOD Rate Register*/ - {S1DREG_LCD_DISP_HWIDTH, 0x4F}, /* LCD Horizontal Display Width Register*/ - {S1DREG_LCD_NDISP_HPER, 0x13}, /* LCD Horizontal Non-Display Period Register*/ - {S1DREG_TFT_FPLINE_START, 0x01}, /* TFT FPLINE Start Position Register*/ - {S1DREG_TFT_FPLINE_PWIDTH, 0x0c}, /* TFT FPLINE Pulse Width Register*/ - {S1DREG_LCD_DISP_VHEIGHT0, 0xDF}, /* LCD Vertical Display Height Register 0*/ - {S1DREG_LCD_DISP_VHEIGHT1, 0x01}, /* LCD Vertical Display Height Register 1*/ - {S1DREG_LCD_NDISP_VPER, 0x2c}, /* LCD Vertical Non-Display Period Register*/ - {S1DREG_TFT_FPFRAME_START, 0x0a}, /* TFT FPFRAME Start Position Register*/ - {S1DREG_TFT_FPFRAME_PWIDTH, 0x02}, /* TFT FPFRAME Pulse Width Register*/ - {S1DREG_LCD_DISP_MODE, 0x05}, /* LCD Display Mode Register*/ - {S1DREG_LCD_MISC, 0x01}, /* LCD Miscellaneous Register*/ - {S1DREG_LCD_DISP_START0, 0x00}, /* LCD Display Start Address Register 0*/ - {S1DREG_LCD_DISP_START1, 0x00}, /* LCD Display Start Address Register 1*/ - {S1DREG_LCD_DISP_START2, 0x00}, /* LCD Display Start Address Register 2*/ - {S1DREG_LCD_MEM_OFF0, 0x80}, /* LCD Memory Address Offset Register 0*/ - {S1DREG_LCD_MEM_OFF1, 0x02}, /* LCD Memory Address Offset Register 1*/ - {S1DREG_LCD_PIX_PAN, 0x03}, /* LCD Pixel Panning Register*/ - {S1DREG_LCD_DISP_FIFO_HTC, 0x00}, /* LCD Display FIFO High Threshold Control Register*/ - {S1DREG_LCD_DISP_FIFO_LTC, 0x00}, /* LCD Display FIFO Low Threshold Control Register*/ - {S1DREG_CRT_DISP_HWIDTH, 0x4F}, /* CRT/TV Horizontal Display Width Register*/ - {S1DREG_CRT_NDISP_HPER, 0x13}, /* CRT/TV Horizontal Non-Display Period Register*/ - {S1DREG_CRT_HRTC_START, 0x01}, /* CRT/TV HRTC Start Position Register*/ - {S1DREG_CRT_HRTC_PWIDTH, 0x0B}, /* CRT/TV HRTC Pulse Width Register*/ - {S1DREG_CRT_DISP_VHEIGHT0, 0xDF}, /* CRT/TV Vertical Display Height Register 0*/ - {S1DREG_CRT_DISP_VHEIGHT1, 0x01}, /* CRT/TV Vertical Display Height Register 1*/ - {S1DREG_CRT_NDISP_VPER, 0x2B}, /* CRT/TV Vertical Non-Display Period Register*/ - {S1DREG_CRT_VRTC_START, 0x09}, /* CRT/TV VRTC Start Position Register*/ - {S1DREG_CRT_VRTC_PWIDTH, 0x01}, /* CRT/TV VRTC Pulse Width Register*/ - {S1DREG_TV_OUT_CTL, 0x18}, /* TV Output Control Register */ - {S1DREG_CRT_DISP_MODE, 0x05}, /* CRT/TV Display Mode Register, 16BPP*/ - {S1DREG_CRT_DISP_START0, 0x00}, /* CRT/TV Display Start Address Register 0*/ - {S1DREG_CRT_DISP_START1, 0x00}, /* CRT/TV Display Start Address Register 1*/ - {S1DREG_CRT_DISP_START2, 0x00}, /* CRT/TV Display Start Address Register 2*/ - {S1DREG_CRT_MEM_OFF0, 0x80}, /* CRT/TV Memory Address Offset Register 0*/ - {S1DREG_CRT_MEM_OFF1, 0x02}, /* CRT/TV Memory Address Offset Register 1*/ - {S1DREG_CRT_PIX_PAN, 0x00}, /* CRT/TV Pixel Panning Register*/ - {S1DREG_CRT_DISP_FIFO_HTC, 0x00}, /* CRT/TV Display FIFO High Threshold Control Register*/ - {S1DREG_CRT_DISP_FIFO_LTC, 0x00}, /* CRT/TV Display FIFO Low Threshold Control Register*/ - {S1DREG_LCD_CUR_CTL, 0x00}, /* LCD Ink/Cursor Control Register*/ - {S1DREG_LCD_CUR_START, 0x01}, /* LCD Ink/Cursor Start Address Register*/ - {S1DREG_LCD_CUR_XPOS0, 0x00}, /* LCD Cursor X Position Register 0*/ - {S1DREG_LCD_CUR_XPOS1, 0x00}, /* LCD Cursor X Position Register 1*/ - {S1DREG_LCD_CUR_YPOS0, 0x00}, /* LCD Cursor Y Position Register 0*/ - {S1DREG_LCD_CUR_YPOS1, 0x00}, /* LCD Cursor Y Position Register 1*/ - {S1DREG_LCD_CUR_BCTL0, 0x00}, /* LCD Ink/Cursor Blue Color 0 Register*/ - {S1DREG_LCD_CUR_GCTL0, 0x00}, /* LCD Ink/Cursor Green Color 0 Register*/ - {S1DREG_LCD_CUR_RCTL0, 0x00}, /* LCD Ink/Cursor Red Color 0 Register*/ - {S1DREG_LCD_CUR_BCTL1, 0x1F}, /* LCD Ink/Cursor Blue Color 1 Register*/ - {S1DREG_LCD_CUR_GCTL1, 0x3F}, /* LCD Ink/Cursor Green Color 1 Register*/ - {S1DREG_LCD_CUR_RCTL1, 0x1F}, /* LCD Ink/Cursor Red Color 1 Register*/ - {S1DREG_LCD_CUR_FIFO_HTC, 0x00}, /* LCD Ink/Cursor FIFO Threshold Register*/ - {S1DREG_CRT_CUR_CTL, 0x00}, /* CRT/TV Ink/Cursor Control Register*/ - {S1DREG_CRT_CUR_START, 0x01}, /* CRT/TV Ink/Cursor Start Address Register*/ - {S1DREG_CRT_CUR_XPOS0, 0x00}, /* CRT/TV Cursor X Position Register 0*/ - {S1DREG_CRT_CUR_XPOS1, 0x00}, /* CRT/TV Cursor X Position Register 1*/ - {S1DREG_CRT_CUR_YPOS0, 0x00}, /* CRT/TV Cursor Y Position Register 0*/ - {S1DREG_CRT_CUR_YPOS1, 0x00}, /* CRT/TV Cursor Y Position Register 1*/ - {S1DREG_CRT_CUR_BCTL0, 0x00}, /* CRT/TV Ink/Cursor Blue Color 0 Register*/ - {S1DREG_CRT_CUR_GCTL0, 0x00}, /* CRT/TV Ink/Cursor Green Color 0 Register*/ - {S1DREG_CRT_CUR_RCTL0, 0x00}, /* CRT/TV Ink/Cursor Red Color 0 Register*/ - {S1DREG_CRT_CUR_BCTL1, 0x1F}, /* CRT/TV Ink/Cursor Blue Color 1 Register*/ - {S1DREG_CRT_CUR_GCTL1, 0x3F}, /* CRT/TV Ink/Cursor Green Color 1 Register*/ - {S1DREG_CRT_CUR_RCTL1, 0x1F}, /* CRT/TV Ink/Cursor Red Color 1 Register*/ - {S1DREG_CRT_CUR_FIFO_HTC, 0x00}, /* CRT/TV Ink/Cursor FIFO Threshold Register*/ - {S1DREG_BBLT_CTL0, 0x00}, /* BitBlt Control Register 0*/ - {S1DREG_BBLT_CTL1, 0x01}, /* BitBlt Control Register 1*/ - {S1DREG_BBLT_CC_EXP, 0x00}, /* BitBlt ROP Code/Color Expansion Register*/ - {S1DREG_BBLT_OP, 0x00}, /* BitBlt Operation Register*/ - {S1DREG_BBLT_SRC_START0, 0x00}, /* BitBlt Source Start Address Register 0*/ - {S1DREG_BBLT_SRC_START1, 0x00}, /* BitBlt Source Start Address Register 1*/ - {S1DREG_BBLT_SRC_START2, 0x00}, /* BitBlt Source Start Address Register 2*/ - {S1DREG_BBLT_DST_START0, 0x00}, /* BitBlt Destination Start Address Register 0*/ - {S1DREG_BBLT_DST_START1, 0x00}, /* BitBlt Destination Start Address Register 1*/ - {S1DREG_BBLT_DST_START2, 0x00}, /* BitBlt Destination Start Address Register 2*/ - {S1DREG_BBLT_MEM_OFF0, 0x00}, /* BitBlt Memory Address Offset Register 0*/ - {S1DREG_BBLT_MEM_OFF1, 0x00}, /* BitBlt Memory Address Offset Register 1*/ - {S1DREG_BBLT_WIDTH0, 0x00}, /* BitBlt Width Register 0*/ - {S1DREG_BBLT_WIDTH1, 0x00}, /* BitBlt Width Register 1*/ - {S1DREG_BBLT_HEIGHT0, 0x00}, /* BitBlt Height Register 0*/ - {S1DREG_BBLT_HEIGHT1, 0x00}, /* BitBlt Height Register 1*/ - {S1DREG_BBLT_BGC0, 0x00}, /* BitBlt Background Color Register 0*/ - {S1DREG_BBLT_BGC1, 0x00}, /* BitBlt Background Color Register 1*/ - {S1DREG_BBLT_FGC0, 0x00}, /* BitBlt Foreground Color Register 0*/ - {S1DREG_BBLT_FGC1, 0x00}, /* BitBlt Foreground Color Register 1*/ - {S1DREG_LKUP_MODE, 0x00}, /* Look-Up Table Mode Register*/ - {S1DREG_LKUP_ADDR, 0x00}, /* Look-Up Table Address Register*/ - {S1DREG_PS_CNF, 0x00}, /* Power Save Configuration Register*/ - {S1DREG_PS_STATUS, 0x00}, /* Power Save Status Register*/ - {S1DREG_CPU2MEM_WDOGT, 0x00}, /* CPU-to-Memory Access Watchdog Timer Register*/ - {S1DREG_COM_DISP_MODE, 0x01}, /* Display Mode Register, LCD only*/ + {S1DREG_MISC, 0x00}, /* Miscellaneous Register*/ + {S1DREG_COM_DISP_MODE, 0x01}, /* Display Mode Register, LCD only*/ + {S1DREG_GPIO_CNF0, 0x00}, /* General IO Pins Configuration Register*/ + {S1DREG_GPIO_CTL0, 0x00}, /* General IO Pins Control Register*/ + {S1DREG_CLK_CNF, 0x11}, /* Memory Clock Configuration Register*/ + {S1DREG_LCD_CLK_CNF, 0x10}, /* LCD Pixel Clock Configuration Register*/ + {S1DREG_CRT_CLK_CNF, 0x12}, /* CRT/TV Pixel Clock Configuration Register*/ + {S1DREG_MPLUG_CLK_CNF, 0x01}, /* MediaPlug Clock Configuration Register*/ + {S1DREG_CPU2MEM_WST_SEL, 0x02}, /* CPU To Memory Wait State Select Register*/ + {S1DREG_MEM_CNF, 0x00}, /* Memory Configuration Register*/ + {S1DREG_SDRAM_REF_RATE, 0x04}, /* DRAM Refresh Rate Register, MCLK source*/ + {S1DREG_SDRAM_TC0, 0x12}, /* DRAM Timings Control Register 0*/ + {S1DREG_SDRAM_TC1, 0x02}, /* DRAM Timings Control Register 1*/ + {S1DREG_PANEL_TYPE, 0x25}, /* Panel Type Register*/ + {S1DREG_MOD_RATE, 0x00}, /* MOD Rate Register*/ + {S1DREG_LCD_DISP_HWIDTH, 0x4F}, /* LCD Horizontal Display Width Register*/ + {S1DREG_LCD_NDISP_HPER, 0x13}, /* LCD Horizontal Non-Display Period Register*/ + {S1DREG_TFT_FPLINE_START, 0x01}, /* TFT FPLINE Start Position Register*/ + {S1DREG_TFT_FPLINE_PWIDTH, 0x0c}, /* TFT FPLINE Pulse Width Register*/ + {S1DREG_LCD_DISP_VHEIGHT0, 0xDF}, /* LCD Vertical Display Height Register 0*/ + {S1DREG_LCD_DISP_VHEIGHT1, 0x01}, /* LCD Vertical Display Height Register 1*/ + {S1DREG_LCD_NDISP_VPER, 0x2c}, /* LCD Vertical Non-Display Period Register*/ + {S1DREG_TFT_FPFRAME_START, 0x0a}, /* TFT FPFRAME Start Position Register*/ + {S1DREG_TFT_FPFRAME_PWIDTH, 0x02}, /* TFT FPFRAME Pulse Width Register*/ + {S1DREG_LCD_DISP_MODE, 0x05}, /* LCD Display Mode Register*/ + {S1DREG_LCD_MISC, 0x01}, /* LCD Miscellaneous Register*/ + {S1DREG_LCD_DISP_START0, 0x00}, /* LCD Display Start Address Register 0*/ + {S1DREG_LCD_DISP_START1, 0x00}, /* LCD Display Start Address Register 1*/ + {S1DREG_LCD_DISP_START2, 0x00}, /* LCD Display Start Address Register 2*/ + {S1DREG_LCD_MEM_OFF0, 0x80}, /* LCD Memory Address Offset Register 0*/ + {S1DREG_LCD_MEM_OFF1, 0x02}, /* LCD Memory Address Offset Register 1*/ + {S1DREG_LCD_PIX_PAN, 0x03}, /* LCD Pixel Panning Register*/ + {S1DREG_LCD_DISP_FIFO_HTC, 0x00}, /* LCD Display FIFO High Threshold Control Register*/ + {S1DREG_LCD_DISP_FIFO_LTC, 0x00}, /* LCD Display FIFO Low Threshold Control Register*/ + {S1DREG_CRT_DISP_HWIDTH, 0x4F}, /* CRT/TV Horizontal Display Width Register*/ + {S1DREG_CRT_NDISP_HPER, 0x13}, /* CRT/TV Horizontal Non-Display Period Register*/ + {S1DREG_CRT_HRTC_START, 0x01}, /* CRT/TV HRTC Start Position Register*/ + {S1DREG_CRT_HRTC_PWIDTH, 0x0B}, /* CRT/TV HRTC Pulse Width Register*/ + {S1DREG_CRT_DISP_VHEIGHT0, 0xDF}, /* CRT/TV Vertical Display Height Register 0*/ + {S1DREG_CRT_DISP_VHEIGHT1, 0x01}, /* CRT/TV Vertical Display Height Register 1*/ + {S1DREG_CRT_NDISP_VPER, 0x2B}, /* CRT/TV Vertical Non-Display Period Register*/ + {S1DREG_CRT_VRTC_START, 0x09}, /* CRT/TV VRTC Start Position Register*/ + {S1DREG_CRT_VRTC_PWIDTH, 0x01}, /* CRT/TV VRTC Pulse Width Register*/ + {S1DREG_TV_OUT_CTL, 0x18}, /* TV Output Control Register */ + {S1DREG_CRT_DISP_MODE, 0x05}, /* CRT/TV Display Mode Register, 16BPP*/ + {S1DREG_CRT_DISP_START0, 0x00}, /* CRT/TV Display Start Address Register 0*/ + {S1DREG_CRT_DISP_START1, 0x00}, /* CRT/TV Display Start Address Register 1*/ + {S1DREG_CRT_DISP_START2, 0x00}, /* CRT/TV Display Start Address Register 2*/ + {S1DREG_CRT_MEM_OFF0, 0x80}, /* CRT/TV Memory Address Offset Register 0*/ + {S1DREG_CRT_MEM_OFF1, 0x02}, /* CRT/TV Memory Address Offset Register 1*/ + {S1DREG_CRT_PIX_PAN, 0x00}, /* CRT/TV Pixel Panning Register*/ + {S1DREG_CRT_DISP_FIFO_HTC, 0x00}, /* CRT/TV Display FIFO High Threshold Control Register*/ + {S1DREG_CRT_DISP_FIFO_LTC, 0x00}, /* CRT/TV Display FIFO Low Threshold Control Register*/ + {S1DREG_LCD_CUR_CTL, 0x00}, /* LCD Ink/Cursor Control Register*/ + {S1DREG_LCD_CUR_START, 0x01}, /* LCD Ink/Cursor Start Address Register*/ + {S1DREG_LCD_CUR_XPOS0, 0x00}, /* LCD Cursor X Position Register 0*/ + {S1DREG_LCD_CUR_XPOS1, 0x00}, /* LCD Cursor X Position Register 1*/ + {S1DREG_LCD_CUR_YPOS0, 0x00}, /* LCD Cursor Y Position Register 0*/ + {S1DREG_LCD_CUR_YPOS1, 0x00}, /* LCD Cursor Y Position Register 1*/ + {S1DREG_LCD_CUR_BCTL0, 0x00}, /* LCD Ink/Cursor Blue Color 0 Register*/ + {S1DREG_LCD_CUR_GCTL0, 0x00}, /* LCD Ink/Cursor Green Color 0 Register*/ + {S1DREG_LCD_CUR_RCTL0, 0x00}, /* LCD Ink/Cursor Red Color 0 Register*/ + {S1DREG_LCD_CUR_BCTL1, 0x1F}, /* LCD Ink/Cursor Blue Color 1 Register*/ + {S1DREG_LCD_CUR_GCTL1, 0x3F}, /* LCD Ink/Cursor Green Color 1 Register*/ + {S1DREG_LCD_CUR_RCTL1, 0x1F}, /* LCD Ink/Cursor Red Color 1 Register*/ + {S1DREG_LCD_CUR_FIFO_HTC, 0x00}, /* LCD Ink/Cursor FIFO Threshold Register*/ + {S1DREG_CRT_CUR_CTL, 0x00}, /* CRT/TV Ink/Cursor Control Register*/ + {S1DREG_CRT_CUR_START, 0x01}, /* CRT/TV Ink/Cursor Start Address Register*/ + {S1DREG_CRT_CUR_XPOS0, 0x00}, /* CRT/TV Cursor X Position Register 0*/ + {S1DREG_CRT_CUR_XPOS1, 0x00}, /* CRT/TV Cursor X Position Register 1*/ + {S1DREG_CRT_CUR_YPOS0, 0x00}, /* CRT/TV Cursor Y Position Register 0*/ + {S1DREG_CRT_CUR_YPOS1, 0x00}, /* CRT/TV Cursor Y Position Register 1*/ + {S1DREG_CRT_CUR_BCTL0, 0x00}, /* CRT/TV Ink/Cursor Blue Color 0 Register*/ + {S1DREG_CRT_CUR_GCTL0, 0x00}, /* CRT/TV Ink/Cursor Green Color 0 Register*/ + {S1DREG_CRT_CUR_RCTL0, 0x00}, /* CRT/TV Ink/Cursor Red Color 0 Register*/ + {S1DREG_CRT_CUR_BCTL1, 0x1F}, /* CRT/TV Ink/Cursor Blue Color 1 Register*/ + {S1DREG_CRT_CUR_GCTL1, 0x3F}, /* CRT/TV Ink/Cursor Green Color 1 Register*/ + {S1DREG_CRT_CUR_RCTL1, 0x1F}, /* CRT/TV Ink/Cursor Red Color 1 Register*/ + {S1DREG_CRT_CUR_FIFO_HTC, 0x00}, /* CRT/TV Ink/Cursor FIFO Threshold Register*/ + {S1DREG_BBLT_CTL0, 0x00}, /* BitBlt Control Register 0*/ + {S1DREG_BBLT_CTL1, 0x01}, /* BitBlt Control Register 1*/ + {S1DREG_BBLT_CC_EXP, 0x00}, /* BitBlt ROP Code/Color Expansion Register*/ + {S1DREG_BBLT_OP, 0x00}, /* BitBlt Operation Register*/ + {S1DREG_BBLT_SRC_START0, 0x00}, /* BitBlt Source Start Address Register 0*/ + {S1DREG_BBLT_SRC_START1, 0x00}, /* BitBlt Source Start Address Register 1*/ + {S1DREG_BBLT_SRC_START2, 0x00}, /* BitBlt Source Start Address Register 2*/ + {S1DREG_BBLT_DST_START0, 0x00}, /* BitBlt Destination Start Address Register 0*/ + {S1DREG_BBLT_DST_START1, 0x00}, /* BitBlt Destination Start Address Register 1*/ + {S1DREG_BBLT_DST_START2, 0x00}, /* BitBlt Destination Start Address Register 2*/ + {S1DREG_BBLT_MEM_OFF0, 0x00}, /* BitBlt Memory Address Offset Register 0*/ + {S1DREG_BBLT_MEM_OFF1, 0x00}, /* BitBlt Memory Address Offset Register 1*/ + {S1DREG_BBLT_WIDTH0, 0x00}, /* BitBlt Width Register 0*/ + {S1DREG_BBLT_WIDTH1, 0x00}, /* BitBlt Width Register 1*/ + {S1DREG_BBLT_HEIGHT0, 0x00}, /* BitBlt Height Register 0*/ + {S1DREG_BBLT_HEIGHT1, 0x00}, /* BitBlt Height Register 1*/ + {S1DREG_BBLT_BGC0, 0x00}, /* BitBlt Background Color Register 0*/ + {S1DREG_BBLT_BGC1, 0x00}, /* BitBlt Background Color Register 1*/ + {S1DREG_BBLT_FGC0, 0x00}, /* BitBlt Foreground Color Register 0*/ + {S1DREG_BBLT_FGC1, 0x00}, /* BitBlt Foreground Color Register 1*/ + {S1DREG_LKUP_MODE, 0x00}, /* Look-Up Table Mode Register*/ + {S1DREG_LKUP_ADDR, 0x00}, /* Look-Up Table Address Register*/ + {S1DREG_PS_CNF, 0x00}, /* Power Save Configuration Register*/ + {S1DREG_PS_STATUS, 0x00}, /* Power Save Status Register*/ + {S1DREG_CPU2MEM_WDOGT, 0x00}, /* CPU-to-Memory Access Watchdog Timer Register*/ + {S1DREG_COM_DISP_MODE, 0x01}, /* Display Mode Register, LCD only*/ }; -static u64 s1dfb_dmamask = 0xffffffffUL; +static u64 s1dfb_dmamask = DMA_BIT_MASK(32); -static struct s1d13xxxfb_pdata yl_9200_s1dfb_pdata = { - .initregs = yl_9200_s1dfb_initregs, - .initregssize = ARRAY_SIZE(yl_9200_s1dfb_initregs), - .platform_init_video = yl_9200_init_video, +static struct s1d13xxxfb_pdata yl9200_s1dfb_pdata = { + .initregs = yl9200_s1dfb_initregs, + .initregssize = ARRAY_SIZE(yl9200_s1dfb_initregs), + .platform_init_video = yl9200_init_video, }; -static struct resource yl_9200_s1dfb_resource[] = { +static struct resource yl9200_s1dfb_resource[] = { [0] = { /* video mem */ - .name = "s1d13xxxfb memory", - /* .name = "s1d13806 memory",*/ - .start = AT91_FB_VMEM_BASE, - .end = AT91_FB_VMEM_BASE + AT91_FB_VMEM_SIZE -1, - .flags = IORESOURCE_MEM, + .name = "s1d13xxxfb memory", + .start = AT91_FB_VMEM_BASE, + .end = AT91_FB_VMEM_BASE + AT91_FB_VMEM_SIZE -1, + .flags = IORESOURCE_MEM, }, [1] = { /* video registers */ - .name = "s1d13xxxfb registers", - /* .name = "s1d13806 registers",*/ - .start = AT91_FB_REG_BASE, - .end = AT91_FB_REG_BASE + AT91_FB_REG_SIZE -1, - .flags = IORESOURCE_MEM, + .name = "s1d13xxxfb registers", + .start = AT91_FB_REG_BASE, + .end = AT91_FB_REG_BASE + AT91_FB_REG_SIZE -1, + .flags = IORESOURCE_MEM, }, }; -static struct platform_device yl_9200_s1dfb_device = { - /*TODO S.Birtles , really we need the chip revision in here as well*/ - .name = "s1d13806fb", - /* .name = "s1d13506fb",*/ - .id = -1, - .dev = { - /*TODO theres a waring here!!*/ - /*WARNING: vmlinux.o(.data+0x2dbc): Section mismatch: reference to .init.text: (between 'yl_9200_s1dfb_pdata' and 's1dfb_dmamask')*/ +static struct platform_device yl9200_s1dfb_device = { + .name = "s1d13806fb", + .id = -1, + .dev = { .dma_mask = &s1dfb_dmamask, - .coherent_dma_mask = 0xffffffff, - .platform_data = &yl_9200_s1dfb_pdata, + .coherent_dma_mask = DMA_BIT_MASK(32), + .platform_data = &yl9200_s1dfb_pdata, }, - .resource = yl_9200_s1dfb_resource, - .num_resources = ARRAY_SIZE(yl_9200_s1dfb_resource), + .resource = yl9200_s1dfb_resource, + .num_resources = ARRAY_SIZE(yl9200_s1dfb_resource), }; -void __init yl_9200_add_device_video(void) +void __init yl9200_add_device_video(void) { - platform_device_register(&yl_9200_s1dfb_device); + platform_device_register(&yl9200_s1dfb_device); } #else - void __init yl_9200_add_device_video(void) {} +void __init yl9200_add_device_video(void) {} #endif -/*this is not called first , yl_9200_map_io is called first*/ -static void __init yl_9200_board_init(void) + +static void __init yl9200_board_init(void) { /* Serial */ at91_add_device_serial(); /* Ethernet */ - at91_add_device_eth(&yl_9200_eth_data); + at91_add_device_eth(&yl9200_eth_data); /* USB Host */ - at91_add_device_usbh(&yl_9200_usbh_data); + at91_add_device_usbh(&yl9200_usbh_data); /* USB Device */ - at91_add_device_udc(&yl_9200_udc_data); - /* pullup_pin it is actually active low, but this is not needed, driver sets it up */ - /*at91_set_multi_drive(yl_9200_udc_data.pullup_pin, 0);*/ - - /* Compact Flash */ - /*at91_add_device_cf(&yl_9200_cf_data);*/ - + at91_add_device_udc(&yl9200_udc_data); /* I2C */ - at91_add_device_i2c(yl_9200_i2c_devices, ARRAY_SIZE(yl_9200_i2c_devices)); - /* SPI */ - /*TODO YL9200 we have 2 spi interfaces touch screen & CAN*/ - /* AT91_PIN_PA5, AT91_PIN_PA6 , are used on the max 485 NOT SPI*/ - - /*touch screen and CAN*/ - at91_add_device_spi(yl_9200_spi_devices, ARRAY_SIZE(yl_9200_spi_devices)); - - /*Basically the TS uses PB11 & PB10 , PB11 is configured by the SPI system BP10 IS NOT USED!!*/ - /* we need this incase the board is running without a touch screen*/ - #if defined(CONFIG_TOUCHSCREEN_ADS7846) || defined(CONFIG_TOUCHSCREEN_ADS7846_MODULE) - at91_init_device_ts(); /*init the touch screen device*/ - #endif - /* DataFlash card */ - at91_add_device_mmc(0, &yl_9200_mmc_data); + at91_add_device_i2c(yl9200_i2c_devices, ARRAY_SIZE(yl9200_i2c_devices)); + /* MMC */ + at91_add_device_mmc(0, &yl9200_mmc_data); /* NAND */ - at91_add_device_nand(&yl_9200_nand_data); + at91_add_device_nand(&yl9200_nand_data); /* NOR Flash */ - platform_device_register(&yl_9200_flash); - /* LEDs. Note!! this does not include the led's we passed for the processor status */ - at91_gpio_leds(yl_9200_leds, ARRAY_SIZE(yl_9200_leds)); - /* VGA */ - /*this is self registered by including the s1d13xxx chip in the kernel build*/ - yl_9200_add_device_video(); + platform_device_register(&yl9200_flash); +#if defined(CONFIG_SPI_ATMEL) || defined(CONFIG_SPI_ATMEL_MODULE) + /* SPI */ + at91_add_device_spi(yl9200_spi_devices, ARRAY_SIZE(yl9200_spi_devices)); + /* Touchscreen */ + yl9200_add_device_ts(); +#endif + /* LEDs. */ + at91_gpio_leds(yl9200_leds, ARRAY_SIZE(yl9200_leds)); /* Push Buttons */ - yl_9200_add_device_buttons(); - /*TODO fixup the Sounder */ -// yl_9200_add_device_sounder(yl_9200_sounder,ARRAY_SIZE(yl_9200_sounder)); - + yl9200_add_device_buttons(); + /* VGA */ + yl9200_add_device_video(); } MACHINE_START(YL9200, "uCdragon YL-9200") - /* Maintainer: S.Birtles*/ - .phys_io = AT91_BASE_SYS, + /* Maintainer: S.Birtles */ + .phys_io = AT91_BASE_SYS, .io_pg_offst = (AT91_VA_BASE_SYS >> 18) & 0xfffc, .boot_params = AT91_SDRAM_BASE + 0x100, - .timer = &at91rm9200_timer, - .map_io = yl_9200_map_io, - .init_irq = yl_9200_init_irq, - .init_machine = yl_9200_board_init, + .timer = &at91rm9200_timer, + .map_io = yl9200_map_io, + .init_irq = yl9200_init_irq, + .init_machine = yl9200_board_init, MACHINE_END diff --git a/arch/arm/mach-at91/clock.c b/arch/arm/mach-at91/clock.c index a33dfe45072..464bdbbf74d 100644 --- a/arch/arm/mach-at91/clock.c +++ b/arch/arm/mach-at91/clock.c @@ -112,12 +112,34 @@ static void pmc_sys_mode(struct clk *clk, int is_on) at91_sys_write(AT91_PMC_SCDR, clk->pmc_mask); } +static void pmc_uckr_mode(struct clk *clk, int is_on) +{ + unsigned int uckr = at91_sys_read(AT91_CKGR_UCKR); + + if (is_on) { + is_on = AT91_PMC_LOCKU; + at91_sys_write(AT91_CKGR_UCKR, uckr | clk->pmc_mask); + } else + at91_sys_write(AT91_CKGR_UCKR, uckr & ~(clk->pmc_mask)); + + do { + cpu_relax(); + } while ((at91_sys_read(AT91_PMC_SR) & AT91_PMC_LOCKU) != is_on); +} + /* USB function clocks (PLLB must be 48 MHz) */ static struct clk udpck = { .name = "udpck", .parent = &pllb, .mode = pmc_sys_mode, }; +static struct clk utmi_clk = { + .name = "utmi_clk", + .parent = &main_clk, + .pmc_mask = AT91_PMC_UPLLEN, /* in CKGR_UCKR */ + .mode = pmc_uckr_mode, + .type = CLK_TYPE_PLL, +}; static struct clk uhpck = { .name = "uhpck", .parent = &pllb, @@ -361,7 +383,7 @@ static void __init init_programmable_clock(struct clk *clk) static int at91_clk_show(struct seq_file *s, void *unused) { - u32 scsr, pcsr, sr; + u32 scsr, pcsr, uckr = 0, sr; struct clk *clk; seq_printf(s, "SCSR = %8x\n", scsr = at91_sys_read(AT91_PMC_SCSR)); @@ -369,7 +391,10 @@ static int at91_clk_show(struct seq_file *s, void *unused) seq_printf(s, "MOR = %8x\n", at91_sys_read(AT91_CKGR_MOR)); seq_printf(s, "MCFR = %8x\n", at91_sys_read(AT91_CKGR_MCFR)); seq_printf(s, "PLLA = %8x\n", at91_sys_read(AT91_CKGR_PLLAR)); - seq_printf(s, "PLLB = %8x\n", at91_sys_read(AT91_CKGR_PLLBR)); + if (!cpu_is_at91sam9rl()) + seq_printf(s, "PLLB = %8x\n", at91_sys_read(AT91_CKGR_PLLBR)); + if (cpu_is_at91cap9() || cpu_is_at91sam9rl()) + seq_printf(s, "UCKR = %8x\n", uckr = at91_sys_read(AT91_CKGR_UCKR)); seq_printf(s, "MCKR = %8x\n", at91_sys_read(AT91_PMC_MCKR)); seq_printf(s, "SR = %8x\n", sr = at91_sys_read(AT91_PMC_SR)); @@ -382,6 +407,8 @@ static int at91_clk_show(struct seq_file *s, void *unused) state = (scsr & clk->pmc_mask) ? "on" : "off"; else if (clk->mode == pmc_periph_mode) state = (pcsr & clk->pmc_mask) ? "on" : "off"; + else if (clk->mode == pmc_uckr_mode) + state = (uckr & clk->pmc_mask) ? "on" : "off"; else if (clk->pmc_mask) state = (sr & clk->pmc_mask) ? "on" : "off"; else if (clk == &clk32k || clk == &main_clk) @@ -488,14 +515,19 @@ static unsigned __init at91_pll_calc(unsigned main_freq, unsigned out_freq) /* * PLL input between 1MHz and 32MHz per spec, but lower * frequences seem necessary in some cases so allow 100K. + * Warning: some newer products need 2MHz min. */ input = main_freq / i; + if (cpu_is_at91sam9g20() && input < 2000000) + continue; if (input < 100000) continue; if (input > 32000000) continue; mul1 = out_freq / input; + if (cpu_is_at91sam9g20() && mul > 63) + continue; if (mul1 > 2048) continue; if (mul1 < 2) @@ -555,7 +587,8 @@ int __init at91_clock_init(unsigned long main_clock) /* report if PLLA is more than mildly overclocked */ plla.rate_hz = at91_pll_rate(&plla, main_clock, at91_sys_read(AT91_CKGR_PLLAR)); - if (plla.rate_hz > 209000000) + if ((!cpu_is_at91sam9g20() && plla.rate_hz > 209000000) + || (cpu_is_at91sam9g20() && plla.rate_hz > 800000000)) pr_info("Clocks: PLLA overclocked, %ld MHz\n", plla.rate_hz / 1000000); /* @@ -570,7 +603,7 @@ int __init at91_clock_init(unsigned long main_clock) uhpck.pmc_mask = AT91RM9200_PMC_UHP; udpck.pmc_mask = AT91RM9200_PMC_UDP; at91_sys_write(AT91_PMC_SCER, AT91RM9200_PMC_MCKUDP); - } else if (cpu_is_at91sam9260() || cpu_is_at91sam9261() || cpu_is_at91sam9263()) { + } else if (cpu_is_at91sam9260() || cpu_is_at91sam9261() || cpu_is_at91sam9263() || cpu_is_at91sam9g20()) { uhpck.pmc_mask = AT91SAM926x_PMC_UHP; udpck.pmc_mask = AT91SAM926x_PMC_UDP; } else if (cpu_is_at91cap9()) { @@ -582,6 +615,17 @@ int __init at91_clock_init(unsigned long main_clock) uhpck.rate_hz = at91_usb_rate(&pllb, pllb.rate_hz, at91_pllb_usb_init); /* + * USB HS clock init + */ + if (cpu_is_at91cap9() || cpu_is_at91sam9rl()) { + /* + * multiplier is hard-wired to 40 + * (obtain the USB High Speed 480 MHz when input is 12 MHz) + */ + utmi_clk.rate_hz = 40 * utmi_clk.parent->rate_hz; + } + + /* * MCK and CPU derive from one of those primary clocks. * For now, assume this parentage won't change. */ @@ -591,13 +635,21 @@ int __init at91_clock_init(unsigned long main_clock) freq /= (1 << ((mckr & AT91_PMC_PRES) >> 2)); /* prescale */ if (cpu_is_at91rm9200()) mck.rate_hz = freq / (1 + ((mckr & AT91_PMC_MDIV) >> 8)); /* mdiv */ - else - mck.rate_hz = freq / (1 << ((mckr & AT91_PMC_MDIV) >> 8)); /* mdiv */ + else if (cpu_is_at91sam9g20()) { + mck.rate_hz = (mckr & AT91_PMC_MDIV) ? + freq / ((mckr & AT91_PMC_MDIV) >> 7) : freq; /* mdiv ; (x >> 7) = ((x >> 8) * 2) */ + if (mckr & AT91_PMC_PDIV) + freq /= 2; /* processor clock division */ + } else + mck.rate_hz = freq / (1 << ((mckr & AT91_PMC_MDIV) >> 8)); /* mdiv */ /* Register the PMC's standard clocks */ for (i = 0; i < ARRAY_SIZE(standard_pmc_clocks); i++) list_add_tail(&standard_pmc_clocks[i]->node, &clocks); + if (cpu_is_at91cap9() || cpu_is_at91sam9rl()) + list_add_tail(&utmi_clk.node, &clocks); + /* MCK and CPU clock are "always on" */ clk_enable(&mck); diff --git a/arch/arm/mach-at91/pm.c b/arch/arm/mach-at91/pm.c index aa863c15770..8ab4feb1ec5 100644 --- a/arch/arm/mach-at91/pm.c +++ b/arch/arm/mach-at91/pm.c @@ -202,7 +202,7 @@ static int at91_pm_verify_clocks(void) pr_debug("AT91: PM - Suspend-to-RAM with USB still active\n"); return 0; } - } else if (cpu_is_at91sam9260() || cpu_is_at91sam9261() || cpu_is_at91sam9263()) { + } else if (cpu_is_at91sam9260() || cpu_is_at91sam9261() || cpu_is_at91sam9263() || cpu_is_at91sam9g20()) { if ((scsr & (AT91SAM926x_PMC_UHP | AT91SAM926x_PMC_UDP)) != 0) { pr_debug("AT91: PM - Suspend-to-RAM with USB still active\n"); return 0; diff --git a/arch/arm/mach-ep93xx/clock.c b/arch/arm/mach-ep93xx/clock.c index 9d7515c36bf..f62c35500bb 100644 --- a/arch/arm/mach-ep93xx/clock.c +++ b/arch/arm/mach-ep93xx/clock.c @@ -74,6 +74,7 @@ struct clk *clk_get(struct device *dev, const char *id) return ERR_PTR(-ENOENT); } +EXPORT_SYMBOL(clk_get); int clk_enable(struct clk *clk) { @@ -86,6 +87,7 @@ int clk_enable(struct clk *clk) return 0; } +EXPORT_SYMBOL(clk_enable); void clk_disable(struct clk *clk) { @@ -96,15 +98,18 @@ void clk_disable(struct clk *clk) __raw_writel(value & ~clk->enable_mask, clk->enable_reg); } } +EXPORT_SYMBOL(clk_disable); unsigned long clk_get_rate(struct clk *clk) { return clk->rate; } +EXPORT_SYMBOL(clk_get_rate); void clk_put(struct clk *clk) { } +EXPORT_SYMBOL(clk_put); diff --git a/arch/arm/mach-footbridge/Makefile b/arch/arm/mach-footbridge/Makefile index 0694ad6b647..32f8609e4f8 100644 --- a/arch/arm/mach-footbridge/Makefile +++ b/arch/arm/mach-footbridge/Makefile @@ -14,12 +14,10 @@ pci-$(CONFIG_ARCH_EBSA285_HOST) += ebsa285-pci.o pci-$(CONFIG_ARCH_NETWINDER) += netwinder-pci.o pci-$(CONFIG_ARCH_PERSONAL_SERVER) += personal-pci.o -leds-$(CONFIG_ARCH_CO285) += ebsa285-leds.o leds-$(CONFIG_ARCH_EBSA285) += ebsa285-leds.o leds-$(CONFIG_ARCH_NETWINDER) += netwinder-leds.o obj-$(CONFIG_ARCH_CATS) += cats-hw.o isa-timer.o -obj-$(CONFIG_ARCH_CO285) += co285.o dc21285-timer.o obj-$(CONFIG_ARCH_EBSA285) += ebsa285.o dc21285-timer.o obj-$(CONFIG_ARCH_NETWINDER) += netwinder-hw.o isa-timer.o obj-$(CONFIG_ARCH_PERSONAL_SERVER) += personal.o dc21285-timer.o diff --git a/arch/arm/mach-footbridge/co285.c b/arch/arm/mach-footbridge/co285.c deleted file mode 100644 index 4545576ad8d..00000000000 --- a/arch/arm/mach-footbridge/co285.c +++ /dev/null @@ -1,39 +0,0 @@ -/* - * linux/arch/arm/mach-footbridge/co285.c - * - * CO285 machine fixup - */ -#include <linux/init.h> - -#include <asm/hardware/dec21285.h> -#include <asm/mach-types.h> - -#include <asm/mach/arch.h> - -#include "common.h" - -static void __init -fixup_coebsa285(struct machine_desc *desc, struct tag *tags, - char **cmdline, struct meminfo *mi) -{ - extern unsigned long boot_memory_end; - extern char boot_command_line[]; - - mi->nr_banks = 1; - mi->bank[0].start = PHYS_OFFSET; - mi->bank[0].size = boot_memory_end; - mi->bank[0].node = 0; - - *cmdline = boot_command_line; -} - -MACHINE_START(CO285, "co-EBSA285") - /* Maintainer: Mark van Doesburg */ - .phys_io = DC21285_ARMCSR_BASE, - .io_pg_offst = ((0x7cf00000) >> 18) & 0xfffc, - .fixup = fixup_coebsa285, - .map_io = footbridge_map_io, - .init_irq = footbridge_init_irq, - .timer = &footbridge_timer, -MACHINE_END - diff --git a/arch/arm/mach-footbridge/common.c b/arch/arm/mach-footbridge/common.c index ef29fc34ce6..b08ab507c05 100644 --- a/arch/arm/mach-footbridge/common.c +++ b/arch/arm/mach-footbridge/common.c @@ -177,25 +177,6 @@ static struct map_desc ebsa285_host_io_desc[] __initdata = { #endif }; -/* - * The CO-ebsa285 mapping. - */ -static struct map_desc co285_io_desc[] __initdata = { -#ifdef CONFIG_ARCH_CO285 - { - .virtual = PCIO_BASE, - .pfn = __phys_to_pfn(DC21285_PCI_IO), - .length = PCIO_SIZE, - .type = MT_DEVICE, - }, { - .virtual = PCIMEM_BASE, - .pfn = __phys_to_pfn(DC21285_PCI_MEM), - .length = PCIMEM_SIZE, - .type = MT_DEVICE, - }, -#endif -}; - void __init footbridge_map_io(void) { /* @@ -208,8 +189,6 @@ void __init footbridge_map_io(void) * Now, work out what we've got to map in addition on this * platform. */ - if (machine_is_co285()) - iotable_init(co285_io_desc, ARRAY_SIZE(co285_io_desc)); if (footbridge_cfn_mode()) iotable_init(ebsa285_host_io_desc, ARRAY_SIZE(ebsa285_host_io_desc)); } diff --git a/arch/arm/mach-footbridge/ebsa285-leds.c b/arch/arm/mach-footbridge/ebsa285-leds.c index a64e2222651..09c1fbc5187 100644 --- a/arch/arm/mach-footbridge/ebsa285-leds.c +++ b/arch/arm/mach-footbridge/ebsa285-leds.c @@ -128,7 +128,7 @@ static void ebsa285_leds_event(led_event_t evt) static int __init leds_init(void) { - if (machine_is_ebsa285() || machine_is_co285()) + if (machine_is_ebsa285()) leds_event = ebsa285_leds_event; leds_event(led_start); diff --git a/arch/arm/mach-footbridge/time.c b/arch/arm/mach-footbridge/time.c index 5d02e95dede..d5cfcda385d 100644 --- a/arch/arm/mach-footbridge/time.c +++ b/arch/arm/mach-footbridge/time.c @@ -115,8 +115,7 @@ static int set_isa_cmos_time(void) void __init isa_rtc_init(void) { - if (machine_is_co285() || - machine_is_personal_server()) + if (machine_is_personal_server()) /* * Add-in 21285s shouldn't access the RTC */ diff --git a/arch/arm/mach-imx/dma.c b/arch/arm/mach-imx/dma.c index a59ff2987cb..ee1c6f06ff6 100644 --- a/arch/arm/mach-imx/dma.c +++ b/arch/arm/mach-imx/dma.c @@ -410,7 +410,6 @@ void imx_dma_free(imx_dmach_t dma_ch) /** * imx_dma_request_by_prio - find and request some of free channels best suiting requested priority - * @dma_ch: i.MX DMA channel number * @name: the driver/caller own non-%NULL identification * @prio: one of the hardware distinguished priority level: * %DMA_PRIO_HIGH, %DMA_PRIO_MEDIUM, %DMA_PRIO_LOW @@ -420,11 +419,9 @@ void imx_dma_free(imx_dmach_t dma_ch) * in the higher and then even lower priority groups. * * Return value: If there is no free channel to allocate, -%ENODEV is returned. - * Zero value indicates successful channel allocation. + * On successful allocation channel is returned. */ -int -imx_dma_request_by_prio(imx_dmach_t * pdma_ch, const char *name, - imx_dma_prio prio) +imx_dmach_t imx_dma_request_by_prio(const char *name, imx_dma_prio prio) { int i; int best; @@ -444,15 +441,13 @@ imx_dma_request_by_prio(imx_dmach_t * pdma_ch, const char *name, for (i = best; i < IMX_DMA_CHANNELS; i++) { if (!imx_dma_request(i, name)) { - *pdma_ch = i; - return 0; + return i; } } for (i = best - 1; i >= 0; i--) { if (!imx_dma_request(i, name)) { - *pdma_ch = i; - return 0; + return i; } } diff --git a/arch/arm/mach-integrator/Makefile b/arch/arm/mach-integrator/Makefile index 158daaf9e3b..6a5ef8d30b1 100644 --- a/arch/arm/mach-integrator/Makefile +++ b/arch/arm/mach-integrator/Makefile @@ -4,7 +4,7 @@ # Object file lists. -obj-y := clock.o core.o lm.o time.o +obj-y := clock.o core.o lm.o obj-$(CONFIG_ARCH_INTEGRATOR_AP) += integrator_ap.o obj-$(CONFIG_ARCH_INTEGRATOR_CP) += integrator_cp.o diff --git a/arch/arm/mach-integrator/time.c b/arch/arm/mach-integrator/time.c deleted file mode 100644 index 8508a0db3ea..00000000000 --- a/arch/arm/mach-integrator/time.c +++ /dev/null @@ -1,223 +0,0 @@ -/* - * linux/arch/arm/mach-integrator/time.c - * - * Copyright (C) 2000-2001 Deep Blue Solutions Ltd. - * - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License version 2 as - * published by the Free Software Foundation. - */ -#include <linux/module.h> -#include <linux/kernel.h> -#include <linux/time.h> -#include <linux/mc146818rtc.h> -#include <linux/interrupt.h> -#include <linux/init.h> -#include <linux/device.h> -#include <linux/amba/bus.h> - -#include <asm/hardware.h> -#include <asm/io.h> -#include <asm/uaccess.h> -#include <asm/rtc.h> - -#include <asm/mach/time.h> - -#define RTC_DR (0) -#define RTC_MR (4) -#define RTC_STAT (8) -#define RTC_EOI (8) -#define RTC_LR (12) -#define RTC_CR (16) -#define RTC_CR_MIE (1 << 0) - -extern int (*set_rtc)(void); -static void __iomem *rtc_base; - -static int integrator_set_rtc(void) -{ - __raw_writel(xtime.tv_sec, rtc_base + RTC_LR); - return 1; -} - -static int integrator_rtc_read_alarm(struct rtc_wkalrm *alrm) -{ - rtc_time_to_tm(readl(rtc_base + RTC_MR), &alrm->time); - return 0; -} - -static inline int integrator_rtc_set_alarm(struct rtc_wkalrm *alrm) -{ - unsigned long time; - int ret; - - /* - * At the moment, we can only deal with non-wildcarded alarm times. - */ - ret = rtc_valid_tm(&alrm->time); - if (ret == 0) - ret = rtc_tm_to_time(&alrm->time, &time); - if (ret == 0) - writel(time, rtc_base + RTC_MR); - return ret; -} - -static int integrator_rtc_read_time(struct rtc_time *tm) -{ - rtc_time_to_tm(readl(rtc_base + RTC_DR), tm); - return 0; -} - -/* - * Set the RTC time. Unfortunately, we can't accurately set - * the point at which the counter updates. - * - * Also, since RTC_LR is transferred to RTC_CR on next rising - * edge of the 1Hz clock, we must write the time one second - * in advance. - */ -static inline int integrator_rtc_set_time(struct rtc_time *tm) -{ - unsigned long time; - int ret; - - ret = rtc_tm_to_time(tm, &time); - if (ret == 0) - writel(time + 1, rtc_base + RTC_LR); - - return ret; -} - -static struct rtc_ops rtc_ops = { - .owner = THIS_MODULE, - .read_time = integrator_rtc_read_time, - .set_time = integrator_rtc_set_time, - .read_alarm = integrator_rtc_read_alarm, - .set_alarm = integrator_rtc_set_alarm, -}; - -static irqreturn_t arm_rtc_interrupt(int irq, void *dev_id) -{ - writel(0, rtc_base + RTC_EOI); - return IRQ_HANDLED; -} - -static int rtc_probe(struct amba_device *dev, void *id) -{ - int ret; - - if (rtc_base) - return -EBUSY; - - ret = amba_request_regions(dev, NULL); - if (ret) - goto out; - - rtc_base = ioremap(dev->res.start, SZ_4K); - if (!rtc_base) { - ret = -ENOMEM; - goto res_out; - } - - __raw_writel(0, rtc_base + RTC_CR); - __raw_writel(0, rtc_base + RTC_EOI); - - xtime.tv_sec = __raw_readl(rtc_base + RTC_DR); - - /* note that 'dev' is merely used for irq disambiguation; - * it is not actually referenced in the irq handler - */ - ret = request_irq(dev->irq[0], arm_rtc_interrupt, IRQF_DISABLED, - "rtc-pl030", dev); - if (ret) - goto map_out; - - ret = register_rtc(&rtc_ops); - if (ret) - goto irq_out; - - set_rtc = integrator_set_rtc; - return 0; - - irq_out: - free_irq(dev->irq[0], dev); - map_out: - iounmap(rtc_base); - rtc_base = NULL; - res_out: - amba_release_regions(dev); - out: - return ret; -} - -static int rtc_remove(struct amba_device *dev) -{ - set_rtc = NULL; - - writel(0, rtc_base + RTC_CR); - - free_irq(dev->irq[0], dev); - unregister_rtc(&rtc_ops); - - iounmap(rtc_base); - rtc_base = NULL; - amba_release_regions(dev); - - return 0; -} - -static struct timespec rtc_delta; - -static int rtc_suspend(struct amba_device *dev, pm_message_t state) -{ - struct timespec rtc; - - rtc.tv_sec = readl(rtc_base + RTC_DR); - rtc.tv_nsec = 0; - save_time_delta(&rtc_delta, &rtc); - - return 0; -} - -static int rtc_resume(struct amba_device *dev) -{ - struct timespec rtc; - - rtc.tv_sec = readl(rtc_base + RTC_DR); - rtc.tv_nsec = 0; - restore_time_delta(&rtc_delta, &rtc); - - return 0; -} - -static struct amba_id rtc_ids[] = { - { - .id = 0x00041030, - .mask = 0x000fffff, - }, - { 0, 0 }, -}; - -static struct amba_driver rtc_driver = { - .drv = { - .name = "rtc-pl030", - }, - .probe = rtc_probe, - .remove = rtc_remove, - .suspend = rtc_suspend, - .resume = rtc_resume, - .id_table = rtc_ids, -}; - -static int __init integrator_rtc_init(void) -{ - return amba_driver_register(&rtc_driver); -} - -static void __exit integrator_rtc_exit(void) -{ - amba_driver_unregister(&rtc_driver); -} - -module_init(integrator_rtc_init); -module_exit(integrator_rtc_exit); diff --git a/arch/arm/mach-ixp4xx/Kconfig b/arch/arm/mach-ixp4xx/Kconfig index e774447c059..db8b5fe06c0 100644 --- a/arch/arm/mach-ixp4xx/Kconfig +++ b/arch/arm/mach-ixp4xx/Kconfig @@ -125,6 +125,15 @@ config ARCH_IXDP4XX depends on ARCH_IXDP425 || MACH_IXDP465 || MACH_KIXRP435 default y +config MACH_FSG + bool + prompt "Freecom FSG-3" + select PCI + help + Say 'Y' here if you want your kernel to support Freecom's + FSG-3 device. For more information on this platform, + see http://www.nslu2-linux.org/wiki/FSG3/HomePage + # # Certain registers and IRQs are only enabled if supporting IXP465 CPUs # diff --git a/arch/arm/mach-ixp4xx/Makefile b/arch/arm/mach-ixp4xx/Makefile index c1956882c48..2e6bbf927a7 100644 --- a/arch/arm/mach-ixp4xx/Makefile +++ b/arch/arm/mach-ixp4xx/Makefile @@ -15,6 +15,7 @@ obj-pci-$(CONFIG_MACH_NAS100D) += nas100d-pci.o obj-pci-$(CONFIG_MACH_DSMG600) += dsmg600-pci.o obj-pci-$(CONFIG_MACH_GATEWAY7001) += gateway7001-pci.o obj-pci-$(CONFIG_MACH_WG302V2) += wg302v2-pci.o +obj-pci-$(CONFIG_MACH_FSG) += fsg-pci.o obj-y += common.o @@ -28,6 +29,7 @@ obj-$(CONFIG_MACH_NAS100D) += nas100d-setup.o obj-$(CONFIG_MACH_DSMG600) += dsmg600-setup.o obj-$(CONFIG_MACH_GATEWAY7001) += gateway7001-setup.o obj-$(CONFIG_MACH_WG302V2) += wg302v2-setup.o +obj-$(CONFIG_MACH_FSG) += fsg-setup.o obj-$(CONFIG_PCI) += $(obj-pci-$(CONFIG_PCI)) common-pci.o obj-$(CONFIG_IXP4XX_QMGR) += ixp4xx_qmgr.o diff --git a/arch/arm/mach-ixp4xx/fsg-pci.c b/arch/arm/mach-ixp4xx/fsg-pci.c new file mode 100644 index 00000000000..f19f3f6feda --- /dev/null +++ b/arch/arm/mach-ixp4xx/fsg-pci.c @@ -0,0 +1,71 @@ +/* + * arch/arch/mach-ixp4xx/fsg-pci.c + * + * FSG board-level PCI initialization + * + * Author: Rod Whitby <rod@whitby.id.au> + * Maintainer: http://www.nslu2-linux.org/ + * + * based on ixdp425-pci.c: + * Copyright (C) 2002 Intel Corporation. + * Copyright (C) 2003-2004 MontaVista Software, Inc. + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + * + */ + +#include <linux/pci.h> +#include <linux/init.h> +#include <linux/irq.h> + +#include <asm/mach/pci.h> +#include <asm/mach-types.h> + +void __init fsg_pci_preinit(void) +{ + set_irq_type(IRQ_FSG_PCI_INTA, IRQT_LOW); + set_irq_type(IRQ_FSG_PCI_INTB, IRQT_LOW); + set_irq_type(IRQ_FSG_PCI_INTC, IRQT_LOW); + + ixp4xx_pci_preinit(); +} + +static int __init fsg_map_irq(struct pci_dev *dev, u8 slot, u8 pin) +{ + static int pci_irq_table[FSG_PCI_IRQ_LINES] = { + IRQ_FSG_PCI_INTC, + IRQ_FSG_PCI_INTB, + IRQ_FSG_PCI_INTA, + }; + + int irq = -1; + slot = slot - 11; + + if (slot >= 1 && slot <= FSG_PCI_MAX_DEV && + pin >= 1 && pin <= FSG_PCI_IRQ_LINES) + irq = pci_irq_table[(slot - 1)]; + printk(KERN_INFO "%s: Mapped slot %d pin %d to IRQ %d\n", + __func__, slot, pin, irq); + + return irq; +} + +struct hw_pci fsg_pci __initdata = { + .nr_controllers = 1, + .preinit = fsg_pci_preinit, + .swizzle = pci_std_swizzle, + .setup = ixp4xx_setup, + .scan = ixp4xx_scan_bus, + .map_irq = fsg_map_irq, +}; + +int __init fsg_pci_init(void) +{ + if (machine_is_fsg()) + pci_common_init(&fsg_pci); + return 0; +} + +subsys_initcall(fsg_pci_init); diff --git a/arch/arm/mach-ixp4xx/fsg-setup.c b/arch/arm/mach-ixp4xx/fsg-setup.c new file mode 100644 index 00000000000..0db3a909ae6 --- /dev/null +++ b/arch/arm/mach-ixp4xx/fsg-setup.c @@ -0,0 +1,276 @@ +/* + * arch/arm/mach-ixp4xx/fsg-setup.c + * + * FSG board-setup + * + * Copyright (C) 2008 Rod Whitby <rod@whitby.id.au> + * + * based on ixdp425-setup.c: + * Copyright (C) 2003-2004 MontaVista Software, Inc. + * based on nslu2-power.c + * Copyright (C) 2005 Tower Technologies + * + * Author: Rod Whitby <rod@whitby.id.au> + * Maintainers: http://www.nslu2-linux.org/ + * + */ + +#include <linux/if_ether.h> +#include <linux/irq.h> +#include <linux/serial.h> +#include <linux/serial_8250.h> +#include <linux/leds.h> +#include <linux/reboot.h> +#include <linux/i2c.h> +#include <linux/i2c-gpio.h> + +#include <asm/mach-types.h> +#include <asm/mach/arch.h> +#include <asm/mach/flash.h> +#include <asm/io.h> +#include <asm/gpio.h> + +static struct flash_platform_data fsg_flash_data = { + .map_name = "cfi_probe", + .width = 2, +}; + +static struct resource fsg_flash_resource = { + .flags = IORESOURCE_MEM, +}; + +static struct platform_device fsg_flash = { + .name = "IXP4XX-Flash", + .id = 0, + .dev = { + .platform_data = &fsg_flash_data, + }, + .num_resources = 1, + .resource = &fsg_flash_resource, +}; + +static struct i2c_gpio_platform_data fsg_i2c_gpio_data = { + .sda_pin = FSG_SDA_PIN, + .scl_pin = FSG_SCL_PIN, +}; + +static struct platform_device fsg_i2c_gpio = { + .name = "i2c-gpio", + .id = 0, + .dev = { + .platform_data = &fsg_i2c_gpio_data, + }, +}; + +static struct i2c_board_info __initdata fsg_i2c_board_info [] = { + { + I2C_BOARD_INFO("rtc-isl1208", 0x6f), + }, +}; + +static struct resource fsg_uart_resources[] = { + { + .start = IXP4XX_UART1_BASE_PHYS, + .end = IXP4XX_UART1_BASE_PHYS + 0x0fff, + .flags = IORESOURCE_MEM, + }, + { + .start = IXP4XX_UART2_BASE_PHYS, + .end = IXP4XX_UART2_BASE_PHYS + 0x0fff, + .flags = IORESOURCE_MEM, + } +}; + +static struct plat_serial8250_port fsg_uart_data[] = { + { + .mapbase = IXP4XX_UART1_BASE_PHYS, + .membase = (char *)IXP4XX_UART1_BASE_VIRT + REG_OFFSET, + .irq = IRQ_IXP4XX_UART1, + .flags = UPF_BOOT_AUTOCONF | UPF_SKIP_TEST, + .iotype = UPIO_MEM, + .regshift = 2, + .uartclk = IXP4XX_UART_XTAL, + }, + { + .mapbase = IXP4XX_UART2_BASE_PHYS, + .membase = (char *)IXP4XX_UART2_BASE_VIRT + REG_OFFSET, + .irq = IRQ_IXP4XX_UART2, + .flags = UPF_BOOT_AUTOCONF | UPF_SKIP_TEST, + .iotype = UPIO_MEM, + .regshift = 2, + .uartclk = IXP4XX_UART_XTAL, + }, + { } +}; + +static struct platform_device fsg_uart = { + .name = "serial8250", + .id = PLAT8250_DEV_PLATFORM, + .dev = { + .platform_data = fsg_uart_data, + }, + .num_resources = ARRAY_SIZE(fsg_uart_resources), + .resource = fsg_uart_resources, +}; + +static struct platform_device fsg_leds = { + .name = "fsg-led", + .id = -1, +}; + +/* Built-in 10/100 Ethernet MAC interfaces */ +static struct eth_plat_info fsg_plat_eth[] = { + { + .phy = 5, + .rxq = 3, + .txreadyq = 20, + }, { + .phy = 4, + .rxq = 4, + .txreadyq = 21, + } +}; + +static struct platform_device fsg_eth[] = { + { + .name = "ixp4xx_eth", + .id = IXP4XX_ETH_NPEB, + .dev = { + .platform_data = fsg_plat_eth, + }, + }, { + .name = "ixp4xx_eth", + .id = IXP4XX_ETH_NPEC, + .dev = { + .platform_data = fsg_plat_eth + 1, + }, + } +}; + +static struct platform_device *fsg_devices[] __initdata = { + &fsg_i2c_gpio, + &fsg_flash, + &fsg_leds, + &fsg_eth[0], + &fsg_eth[1], +}; + +static irqreturn_t fsg_power_handler(int irq, void *dev_id) +{ + /* Signal init to do the ctrlaltdel action, this will bypass init if + * it hasn't started and do a kernel_restart. + */ + ctrl_alt_del(); + + return IRQ_HANDLED; +} + +static irqreturn_t fsg_reset_handler(int irq, void *dev_id) +{ + /* This is the paper-clip reset which does an emergency reboot. */ + printk(KERN_INFO "Restarting system.\n"); + machine_restart(NULL); + + /* This should never be reached. */ + return IRQ_HANDLED; +} + +static void __init fsg_init(void) +{ + DECLARE_MAC_BUF(mac_buf); + uint8_t __iomem *f; + int i; + + ixp4xx_sys_init(); + + fsg_flash_resource.start = IXP4XX_EXP_BUS_BASE(0); + fsg_flash_resource.end = + IXP4XX_EXP_BUS_BASE(0) + ixp4xx_exp_bus_size - 1; + + *IXP4XX_EXP_CS0 |= IXP4XX_FLASH_WRITABLE; + *IXP4XX_EXP_CS1 = *IXP4XX_EXP_CS0; + + /* Configure CS2 for operation, 8bit and writable */ + *IXP4XX_EXP_CS2 = 0xbfff0002; + + i2c_register_board_info(0, fsg_i2c_board_info, + ARRAY_SIZE(fsg_i2c_board_info)); + + /* This is only useful on a modified machine, but it is valuable + * to have it first in order to see debug messages, and so that + * it does *not* get removed if platform_add_devices fails! + */ + (void)platform_device_register(&fsg_uart); + + platform_add_devices(fsg_devices, ARRAY_SIZE(fsg_devices)); + + if (request_irq(gpio_to_irq(FSG_RB_GPIO), &fsg_reset_handler, + IRQF_DISABLED | IRQF_TRIGGER_LOW, + "FSG reset button", NULL) < 0) { + + printk(KERN_DEBUG "Reset Button IRQ %d not available\n", + gpio_to_irq(FSG_RB_GPIO)); + } + + if (request_irq(gpio_to_irq(FSG_SB_GPIO), &fsg_power_handler, + IRQF_DISABLED | IRQF_TRIGGER_LOW, + "FSG power button", NULL) < 0) { + + printk(KERN_DEBUG "Power Button IRQ %d not available\n", + gpio_to_irq(FSG_SB_GPIO)); + } + + /* + * Map in a portion of the flash and read the MAC addresses. + * Since it is stored in BE in the flash itself, we need to + * byteswap it if we're in LE mode. + */ + f = ioremap(IXP4XX_EXP_BUS_BASE(0), 0x400000); + if (f) { +#ifdef __ARMEB__ + for (i = 0; i < 6; i++) { + fsg_plat_eth[0].hwaddr[i] = readb(f + 0x3C0422 + i); + fsg_plat_eth[1].hwaddr[i] = readb(f + 0x3C043B + i); + } +#else + + /* + Endian-swapped reads from unaligned addresses are + required to extract the two MACs from the big-endian + Redboot config area in flash. + */ + + fsg_plat_eth[0].hwaddr[0] = readb(f + 0x3C0421); + fsg_plat_eth[0].hwaddr[1] = readb(f + 0x3C0420); + fsg_plat_eth[0].hwaddr[2] = readb(f + 0x3C0427); + fsg_plat_eth[0].hwaddr[3] = readb(f + 0x3C0426); + fsg_plat_eth[0].hwaddr[4] = readb(f + 0x3C0425); + fsg_plat_eth[0].hwaddr[5] = readb(f + 0x3C0424); + + fsg_plat_eth[1].hwaddr[0] = readb(f + 0x3C0439); + fsg_plat_eth[1].hwaddr[1] = readb(f + 0x3C043F); + fsg_plat_eth[1].hwaddr[2] = readb(f + 0x3C043E); + fsg_plat_eth[1].hwaddr[3] = readb(f + 0x3C043D); + fsg_plat_eth[1].hwaddr[4] = readb(f + 0x3C043C); + fsg_plat_eth[1].hwaddr[5] = readb(f + 0x3C0443); +#endif + iounmap(f); + } + printk(KERN_INFO "FSG: Using MAC address %s for port 0\n", + print_mac(mac_buf, fsg_plat_eth[0].hwaddr)); + printk(KERN_INFO "FSG: Using MAC address %s for port 1\n", + print_mac(mac_buf, fsg_plat_eth[1].hwaddr)); + +} + +MACHINE_START(FSG, "Freecom FSG-3") + /* Maintainer: www.nslu2-linux.org */ + .phys_io = IXP4XX_PERIPHERAL_BASE_PHYS, + .io_pg_offst = ((IXP4XX_PERIPHERAL_BASE_VIRT) >> 18) & 0xfffc, + .map_io = ixp4xx_map_io, + .init_irq = ixp4xx_init_irq, + .timer = &ixp4xx_timer, + .boot_params = 0x0100, + .init_machine = fsg_init, +MACHINE_END + diff --git a/arch/arm/mach-kirkwood/Kconfig b/arch/arm/mach-kirkwood/Kconfig new file mode 100644 index 00000000000..3600cd9f051 --- /dev/null +++ b/arch/arm/mach-kirkwood/Kconfig @@ -0,0 +1,25 @@ +if ARCH_KIRKWOOD + +menu "Marvell Kirkwood Implementations" + +config MACH_DB88F6281_BP + bool "Marvell DB-88F6281-BP Development Board" + help + Say 'Y' here if you want your kernel to support the + Marvell DB-88F6281-BP Development Board. + +config MACH_RD88F6192_NAS + bool "Marvell RD-88F6192-NAS Reference Board" + help + Say 'Y' here if you want your kernel to support the + Marvell RD-88F6192-NAS Reference Board. + +config MACH_RD88F6281 + bool "Marvell RD-88F6281 Reference Board" + help + Say 'Y' here if you want your kernel to support the + Marvell RD-88F6281 Reference Board. + +endmenu + +endif diff --git a/arch/arm/mach-kirkwood/Makefile b/arch/arm/mach-kirkwood/Makefile new file mode 100644 index 00000000000..e14bf40bfb0 --- /dev/null +++ b/arch/arm/mach-kirkwood/Makefile @@ -0,0 +1,5 @@ +obj-y += common.o addr-map.o irq.o pcie.o + +obj-$(CONFIG_MACH_DB88F6281_BP) += db88f6281-bp-setup.o +obj-$(CONFIG_MACH_RD88F6192_NAS) += rd88f6192-nas-setup.o +obj-$(CONFIG_MACH_RD88F6192_NAS) += rd88f6281-setup.o diff --git a/arch/arm/mach-kirkwood/Makefile.boot b/arch/arm/mach-kirkwood/Makefile.boot new file mode 100644 index 00000000000..67039c3e0c4 --- /dev/null +++ b/arch/arm/mach-kirkwood/Makefile.boot @@ -0,0 +1,3 @@ + zreladdr-y := 0x00008000 +params_phys-y := 0x00000100 +initrd_phys-y := 0x00800000 diff --git a/arch/arm/mach-kirkwood/addr-map.c b/arch/arm/mach-kirkwood/addr-map.c new file mode 100644 index 00000000000..a39f0f3c473 --- /dev/null +++ b/arch/arm/mach-kirkwood/addr-map.c @@ -0,0 +1,139 @@ +/* + * arch/arm/mach-kirkwood/addr-map.c + * + * Address map functions for Marvell Kirkwood SoCs + * + * This file is licensed under the terms of the GNU General Public + * License version 2. This program is licensed "as is" without any + * warranty of any kind, whether express or implied. + */ + +#include <linux/kernel.h> +#include <linux/init.h> +#include <linux/mbus.h> +#include <linux/io.h> +#include <asm/hardware.h> +#include "common.h" + +/* + * Generic Address Decode Windows bit settings + */ +#define TARGET_DDR 0 +#define TARGET_DEV_BUS 1 +#define TARGET_PCIE 4 +#define ATTR_DEV_SPI_ROM 0x1e +#define ATTR_DEV_BOOT 0x1d +#define ATTR_DEV_NAND 0x2f +#define ATTR_DEV_CS3 0x37 +#define ATTR_DEV_CS2 0x3b +#define ATTR_DEV_CS1 0x3d +#define ATTR_DEV_CS0 0x3e +#define ATTR_PCIE_IO 0xe0 +#define ATTR_PCIE_MEM 0xe8 + +/* + * Helpers to get DDR bank info + */ +#define DDR_BASE_CS_OFF(n) (0x0000 + ((n) << 3)) +#define DDR_SIZE_CS_OFF(n) (0x0004 + ((n) << 3)) + +/* + * CPU Address Decode Windows registers + */ +#define WIN_OFF(n) (BRIDGE_VIRT_BASE + 0x0000 + ((n) << 4)) +#define WIN_CTRL_OFF 0x0000 +#define WIN_BASE_OFF 0x0004 +#define WIN_REMAP_LO_OFF 0x0008 +#define WIN_REMAP_HI_OFF 0x000c + + +struct mbus_dram_target_info kirkwood_mbus_dram_info; + +static int __init cpu_win_can_remap(int win) +{ + if (win < 4) + return 1; + + return 0; +} + +static void __init setup_cpu_win(int win, u32 base, u32 size, + u8 target, u8 attr, int remap) +{ + void __iomem *addr = (void __iomem *)WIN_OFF(win); + u32 ctrl; + + base &= 0xffff0000; + ctrl = ((size - 1) & 0xffff0000) | (attr << 8) | (target << 4) | 1; + + writel(base, addr + WIN_BASE_OFF); + writel(ctrl, addr + WIN_CTRL_OFF); + if (cpu_win_can_remap(win)) { + if (remap < 0) + remap = base; + + writel(remap & 0xffff0000, addr + WIN_REMAP_LO_OFF); + writel(0, addr + WIN_REMAP_HI_OFF); + } +} + +void __init kirkwood_setup_cpu_mbus(void) +{ + void __iomem *addr; + int i; + int cs; + + /* + * First, disable and clear windows. + */ + for (i = 0; i < 8; i++) { + addr = (void __iomem *)WIN_OFF(i); + + writel(0, addr + WIN_BASE_OFF); + writel(0, addr + WIN_CTRL_OFF); + if (cpu_win_can_remap(i)) { + writel(0, addr + WIN_REMAP_LO_OFF); + writel(0, addr + WIN_REMAP_HI_OFF); + } + } + + /* + * Setup windows for PCIe IO+MEM space. + */ + setup_cpu_win(0, KIRKWOOD_PCIE_IO_PHYS_BASE, KIRKWOOD_PCIE_IO_SIZE, + TARGET_PCIE, ATTR_PCIE_IO, KIRKWOOD_PCIE_IO_BUS_BASE); + setup_cpu_win(1, KIRKWOOD_PCIE_MEM_PHYS_BASE, KIRKWOOD_PCIE_MEM_SIZE, + TARGET_PCIE, ATTR_PCIE_MEM, -1); + + /* + * Setup window for NAND controller. + */ + setup_cpu_win(2, KIRKWOOD_NAND_MEM_PHYS_BASE, KIRKWOOD_NAND_MEM_SIZE, + TARGET_DEV_BUS, ATTR_DEV_NAND, -1); + + /* + * Setup MBUS dram target info. + */ + kirkwood_mbus_dram_info.mbus_dram_target_id = TARGET_DDR; + + addr = (void __iomem *)DDR_WINDOW_CPU_BASE; + + for (i = 0, cs = 0; i < 4; i++) { + u32 base = readl(addr + DDR_BASE_CS_OFF(i)); + u32 size = readl(addr + DDR_SIZE_CS_OFF(i)); + + /* + * Chip select enabled? + */ + if (size & 1) { + struct mbus_dram_window *w; + + w = &kirkwood_mbus_dram_info.cs[cs++]; + w->cs_index = i; + w->mbus_attr = 0xf & ~(1 << i); + w->base = base & 0xffff0000; + w->size = (size | 0x0000ffff) + 1; + } + } + kirkwood_mbus_dram_info.num_cs = cs; +} diff --git a/arch/arm/mach-kirkwood/common.c b/arch/arm/mach-kirkwood/common.c new file mode 100644 index 00000000000..5938a3b33cd --- /dev/null +++ b/arch/arm/mach-kirkwood/common.c @@ -0,0 +1,331 @@ +/* + * arch/arm/mach-kirkwood/common.c + * + * Core functions for Marvell Kirkwood SoCs + * + * This file is licensed under the terms of the GNU General Public + * License version 2. This program is licensed "as is" without any + * warranty of any kind, whether express or implied. + */ + +#include <linux/kernel.h> +#include <linux/init.h> +#include <linux/platform_device.h> +#include <linux/serial_8250.h> +#include <linux/mbus.h> +#include <linux/mv643xx_eth.h> +#include <linux/ata_platform.h> +#include <asm/page.h> +#include <asm/timex.h> +#include <asm/mach/map.h> +#include <asm/mach/time.h> +#include <asm/arch/kirkwood.h> +#include <asm/plat-orion/cache-feroceon-l2.h> +#include <asm/plat-orion/ehci-orion.h> +#include <asm/plat-orion/orion_nand.h> +#include <asm/plat-orion/time.h> +#include "common.h" + +/***************************************************************************** + * I/O Address Mapping + ****************************************************************************/ +static struct map_desc kirkwood_io_desc[] __initdata = { + { + .virtual = KIRKWOOD_PCIE_IO_VIRT_BASE, + .pfn = __phys_to_pfn(KIRKWOOD_PCIE_IO_PHYS_BASE), + .length = KIRKWOOD_PCIE_IO_SIZE, + .type = MT_DEVICE, + }, { + .virtual = KIRKWOOD_REGS_VIRT_BASE, + .pfn = __phys_to_pfn(KIRKWOOD_REGS_PHYS_BASE), + .length = KIRKWOOD_REGS_SIZE, + .type = MT_DEVICE, + }, +}; + +void __init kirkwood_map_io(void) +{ + iotable_init(kirkwood_io_desc, ARRAY_SIZE(kirkwood_io_desc)); +} + + +/***************************************************************************** + * EHCI + ****************************************************************************/ +static struct orion_ehci_data kirkwood_ehci_data = { + .dram = &kirkwood_mbus_dram_info, +}; + +static u64 ehci_dmamask = 0xffffffffUL; + + +/***************************************************************************** + * EHCI0 + ****************************************************************************/ +static struct resource kirkwood_ehci_resources[] = { + { + .start = USB_PHYS_BASE, + .end = USB_PHYS_BASE + 0x0fff, + .flags = IORESOURCE_MEM, + }, { + .start = IRQ_KIRKWOOD_USB, + .end = IRQ_KIRKWOOD_USB, + .flags = IORESOURCE_IRQ, + }, +}; + +static struct platform_device kirkwood_ehci = { + .name = "orion-ehci", + .id = 0, + .dev = { + .dma_mask = &ehci_dmamask, + .coherent_dma_mask = 0xffffffff, + .platform_data = &kirkwood_ehci_data, + }, + .resource = kirkwood_ehci_resources, + .num_resources = ARRAY_SIZE(kirkwood_ehci_resources), +}; + +void __init kirkwood_ehci_init(void) +{ + platform_device_register(&kirkwood_ehci); +} + + +/***************************************************************************** + * GE00 + ****************************************************************************/ +struct mv643xx_eth_shared_platform_data kirkwood_ge00_shared_data = { + .t_clk = KIRKWOOD_TCLK, + .dram = &kirkwood_mbus_dram_info, +}; + +static struct resource kirkwood_ge00_shared_resources[] = { + { + .name = "ge00 base", + .start = GE00_PHYS_BASE + 0x2000, + .end = GE00_PHYS_BASE + 0x3fff, + .flags = IORESOURCE_MEM, + }, +}; + +static struct platform_device kirkwood_ge00_shared = { + .name = MV643XX_ETH_SHARED_NAME, + .id = 0, + .dev = { + .platform_data = &kirkwood_ge00_shared_data, + }, + .num_resources = 1, + .resource = kirkwood_ge00_shared_resources, +}; + +static struct resource kirkwood_ge00_resources[] = { + { + .name = "ge00 irq", + .start = IRQ_KIRKWOOD_GE00_SUM, + .end = IRQ_KIRKWOOD_GE00_SUM, + .flags = IORESOURCE_IRQ, + }, +}; + +static struct platform_device kirkwood_ge00 = { + .name = MV643XX_ETH_NAME, + .id = 0, + .num_resources = 1, + .resource = kirkwood_ge00_resources, +}; + +void __init kirkwood_ge00_init(struct mv643xx_eth_platform_data *eth_data) +{ + eth_data->shared = &kirkwood_ge00_shared; + kirkwood_ge00.dev.platform_data = eth_data; + + platform_device_register(&kirkwood_ge00_shared); + platform_device_register(&kirkwood_ge00); +} + + +/***************************************************************************** + * SoC RTC + ****************************************************************************/ +static struct resource kirkwood_rtc_resource = { + .start = RTC_PHYS_BASE, + .end = RTC_PHYS_BASE + SZ_16 - 1, + .flags = IORESOURCE_MEM, +}; + +void __init kirkwood_rtc_init(void) +{ + platform_device_register_simple("rtc-mv", -1, &kirkwood_rtc_resource, 1); +} + + +/***************************************************************************** + * SATA + ****************************************************************************/ +static struct resource kirkwood_sata_resources[] = { + { + .name = "sata base", + .start = SATA_PHYS_BASE, + .end = SATA_PHYS_BASE + 0x5000 - 1, + .flags = IORESOURCE_MEM, + }, { + .name = "sata irq", + .start = IRQ_KIRKWOOD_SATA, + .end = IRQ_KIRKWOOD_SATA, + .flags = IORESOURCE_IRQ, + }, +}; + +static struct platform_device kirkwood_sata = { + .name = "sata_mv", + .id = 0, + .dev = { + .coherent_dma_mask = 0xffffffff, + }, + .num_resources = ARRAY_SIZE(kirkwood_sata_resources), + .resource = kirkwood_sata_resources, +}; + +void __init kirkwood_sata_init(struct mv_sata_platform_data *sata_data) +{ + sata_data->dram = &kirkwood_mbus_dram_info; + kirkwood_sata.dev.platform_data = sata_data; + platform_device_register(&kirkwood_sata); +} + + +/***************************************************************************** + * UART0 + ****************************************************************************/ +static struct plat_serial8250_port kirkwood_uart0_data[] = { + { + .mapbase = UART0_PHYS_BASE, + .membase = (char *)UART0_VIRT_BASE, + .irq = IRQ_KIRKWOOD_UART_0, + .flags = UPF_SKIP_TEST | UPF_BOOT_AUTOCONF, + .iotype = UPIO_MEM, + .regshift = 2, + .uartclk = KIRKWOOD_TCLK, + }, { + }, +}; + +static struct resource kirkwood_uart0_resources[] = { + { + .start = UART0_PHYS_BASE, + .end = UART0_PHYS_BASE + 0xff, + .flags = IORESOURCE_MEM, + }, { + .start = IRQ_KIRKWOOD_UART_0, + .end = IRQ_KIRKWOOD_UART_0, + .flags = IORESOURCE_IRQ, + }, +}; + +static struct platform_device kirkwood_uart0 = { + .name = "serial8250", + .id = 0, + .dev = { + .platform_data = kirkwood_uart0_data, + }, + .resource = kirkwood_uart0_resources, + .num_resources = ARRAY_SIZE(kirkwood_uart0_resources), +}; + +void __init kirkwood_uart0_init(void) +{ + platform_device_register(&kirkwood_uart0); +} + + +/***************************************************************************** + * UART1 + ****************************************************************************/ +static struct plat_serial8250_port kirkwood_uart1_data[] = { + { + .mapbase = UART1_PHYS_BASE, + .membase = (char *)UART1_VIRT_BASE, + .irq = IRQ_KIRKWOOD_UART_1, + .flags = UPF_SKIP_TEST | UPF_BOOT_AUTOCONF, + .iotype = UPIO_MEM, + .regshift = 2, + .uartclk = KIRKWOOD_TCLK, + }, { + }, +}; + +static struct resource kirkwood_uart1_resources[] = { + { + .start = UART1_PHYS_BASE, + .end = UART1_PHYS_BASE + 0xff, + .flags = IORESOURCE_MEM, + }, { + .start = IRQ_KIRKWOOD_UART_1, + .end = IRQ_KIRKWOOD_UART_1, + .flags = IORESOURCE_IRQ, + }, +}; + +static struct platform_device kirkwood_uart1 = { + .name = "serial8250", + .id = 1, + .dev = { + .platform_data = kirkwood_uart1_data, + }, + .resource = kirkwood_uart1_resources, + .num_resources = ARRAY_SIZE(kirkwood_uart1_resources), +}; + +void __init kirkwood_uart1_init(void) +{ + platform_device_register(&kirkwood_uart1); +} + + +/***************************************************************************** + * Time handling + ****************************************************************************/ +static void kirkwood_timer_init(void) +{ + orion_time_init(IRQ_KIRKWOOD_BRIDGE, KIRKWOOD_TCLK); +} + +struct sys_timer kirkwood_timer = { + .init = kirkwood_timer_init, +}; + + +/***************************************************************************** + * General + ****************************************************************************/ +static char * __init kirkwood_id(void) +{ + switch (readl(DEVICE_ID) & 0x3) { + case 0: + return "88F6180"; + case 1: + return "88F6192"; + case 2: + return "88F6281"; + } + + return "unknown 88F6000 variant"; +} + +static int __init is_l2_writethrough(void) +{ + return !!(readl(L2_CONFIG_REG) & L2_WRITETHROUGH); +} + +void __init kirkwood_init(void) +{ + printk(KERN_INFO "Kirkwood: %s, TCLK=%d.\n", + kirkwood_id(), KIRKWOOD_TCLK); + + kirkwood_setup_cpu_mbus(); + +#ifdef CONFIG_CACHE_FEROCEON_L2 + feroceon_l2_init(is_l2_writethrough()); +#endif +} diff --git a/arch/arm/mach-kirkwood/common.h b/arch/arm/mach-kirkwood/common.h new file mode 100644 index 00000000000..5dee2f6b40a --- /dev/null +++ b/arch/arm/mach-kirkwood/common.h @@ -0,0 +1,42 @@ +/* + * arch/arm/mach-kirkwood/common.h + * + * Core functions for Marvell Kirkwood SoCs + * + * This file is licensed under the terms of the GNU General Public + * License version 2. This program is licensed "as is" without any + * warranty of any kind, whether express or implied. + */ + +#ifndef __ARCH_KIRKWOOD_COMMON_H +#define __ARCH_KIRKWOOD_COMMON_H + +struct mv643xx_eth_platform_data; +struct mv_sata_platform_data; + +/* + * Basic Kirkwood init functions used early by machine-setup. + */ +void kirkwood_map_io(void); +void kirkwood_init(void); +void kirkwood_init_irq(void); + +extern struct mbus_dram_target_info kirkwood_mbus_dram_info; +void kirkwood_setup_cpu_mbus(void); +void kirkwood_setup_pcie_io_win(int window, u32 base, u32 size, + int maj, int min); +void kirkwood_setup_pcie_mem_win(int window, u32 base, u32 size, + int maj, int min); + +void kirkwood_ehci_init(void); +void kirkwood_ge00_init(struct mv643xx_eth_platform_data *eth_data); +void kirkwood_pcie_init(void); +void kirkwood_rtc_init(void); +void kirkwood_sata_init(struct mv_sata_platform_data *sata_data); +void kirkwood_uart0_init(void); +void kirkwood_uart1_init(void); + +extern struct sys_timer kirkwood_timer; + + +#endif diff --git a/arch/arm/mach-kirkwood/db88f6281-bp-setup.c b/arch/arm/mach-kirkwood/db88f6281-bp-setup.c new file mode 100644 index 00000000000..d5c482c628e --- /dev/null +++ b/arch/arm/mach-kirkwood/db88f6281-bp-setup.c @@ -0,0 +1,68 @@ +/* + * arch/arm/mach-kirkwood/db88f6281-bp-setup.c + * + * Marvell DB-88F6281-BP Development Board Setup + * + * This file is licensed under the terms of the GNU General Public + * License version 2. This program is licensed "as is" without any + * warranty of any kind, whether express or implied. + */ + +#include <linux/kernel.h> +#include <linux/init.h> +#include <linux/platform_device.h> +#include <linux/pci.h> +#include <linux/irq.h> +#include <linux/mtd/physmap.h> +#include <linux/mtd/nand.h> +#include <linux/timer.h> +#include <linux/ata_platform.h> +#include <linux/mv643xx_eth.h> +#include <asm/mach-types.h> +#include <asm/mach/arch.h> +#include <asm/mach/pci.h> +#include <asm/arch/kirkwood.h> +#include "common.h" + +static struct mv643xx_eth_platform_data db88f6281_ge00_data = { + .phy_addr = 8, +}; + +static struct mv_sata_platform_data db88f6281_sata_data = { + .n_ports = 2, +}; + +static void __init db88f6281_init(void) +{ + /* + * Basic setup. Needs to be called early. + */ + kirkwood_init(); + + kirkwood_ehci_init(); + kirkwood_ge00_init(&db88f6281_ge00_data); + kirkwood_rtc_init(); + kirkwood_sata_init(&db88f6281_sata_data); + kirkwood_uart0_init(); + kirkwood_uart1_init(); +} + +static int __init db88f6281_pci_init(void) +{ + if (machine_is_db88f6281_bp()) + kirkwood_pcie_init(); + + return 0; +} +subsys_initcall(db88f6281_pci_init); + +MACHINE_START(DB88F6281_BP, "Marvell DB-88F6281-BP Development Board") + /* Maintainer: Saeed Bishara <saeed@marvell.com> */ + .phys_io = KIRKWOOD_REGS_PHYS_BASE, + .io_pg_offst = ((KIRKWOOD_REGS_VIRT_BASE) >> 18) & 0xfffc, + .boot_params = 0x00000100, + .init_machine = db88f6281_init, + .map_io = kirkwood_map_io, + .init_irq = kirkwood_init_irq, + .timer = &kirkwood_timer, +MACHINE_END diff --git a/arch/arm/mach-kirkwood/irq.c b/arch/arm/mach-kirkwood/irq.c new file mode 100644 index 00000000000..302bb2cf666 --- /dev/null +++ b/arch/arm/mach-kirkwood/irq.c @@ -0,0 +1,22 @@ +/* + * arch/arm/mach-kirkwood/irq.c + * + * Kirkwood IRQ handling. + * + * This file is licensed under the terms of the GNU General Public + * License version 2. This program is licensed "as is" without any + * warranty of any kind, whether express or implied. + */ + +#include <linux/kernel.h> +#include <linux/init.h> +#include <linux/irq.h> +#include <linux/io.h> +#include <asm/plat-orion/irq.h> +#include "common.h" + +void __init kirkwood_init_irq(void) +{ + orion_irq_init(0, (void __iomem *)(IRQ_VIRT_BASE + IRQ_MASK_LOW_OFF)); + orion_irq_init(32, (void __iomem *)(IRQ_VIRT_BASE + IRQ_MASK_HIGH_OFF)); +} diff --git a/arch/arm/mach-kirkwood/pcie.c b/arch/arm/mach-kirkwood/pcie.c new file mode 100644 index 00000000000..8282d0ff84b --- /dev/null +++ b/arch/arm/mach-kirkwood/pcie.c @@ -0,0 +1,180 @@ +/* + * arch/arm/mach-kirkwood/pcie.c + * + * PCIe functions for Marvell Kirkwood SoCs + * + * This file is licensed under the terms of the GNU General Public + * License version 2. This program is licensed "as is" without any + * warranty of any kind, whether express or implied. + */ + +#include <linux/kernel.h> +#include <linux/pci.h> +#include <linux/mbus.h> +#include <asm/mach/pci.h> +#include <asm/plat-orion/pcie.h> +#include "common.h" + + +#define PCIE_BASE ((void __iomem *)PCIE_VIRT_BASE) + +static int pcie_valid_config(int bus, int dev) +{ + /* + * Don't go out when trying to access -- + * 1. nonexisting device on local bus + * 2. where there's no device connected (no link) + */ + if (bus == 0 && dev == 0) + return 1; + + if (!orion_pcie_link_up(PCIE_BASE)) + return 0; + + if (bus == 0 && dev != 1) + return 0; + + return 1; +} + + +/* + * PCIe config cycles are done by programming the PCIE_CONF_ADDR register + * and then reading the PCIE_CONF_DATA register. Need to make sure these + * transactions are atomic. + */ +static DEFINE_SPINLOCK(kirkwood_pcie_lock); + +static int pcie_rd_conf(struct pci_bus *bus, u32 devfn, int where, + int size, u32 *val) +{ + unsigned long flags; + int ret; + + if (pcie_valid_config(bus->number, PCI_SLOT(devfn)) == 0) { + *val = 0xffffffff; + return PCIBIOS_DEVICE_NOT_FOUND; + } + + spin_lock_irqsave(&kirkwood_pcie_lock, flags); + ret = orion_pcie_rd_conf(PCIE_BASE, bus, devfn, where, size, val); + spin_unlock_irqrestore(&kirkwood_pcie_lock, flags); + + return ret; +} + +static int pcie_wr_conf(struct pci_bus *bus, u32 devfn, + int where, int size, u32 val) +{ + unsigned long flags; + int ret; + + if (pcie_valid_config(bus->number, PCI_SLOT(devfn)) == 0) + return PCIBIOS_DEVICE_NOT_FOUND; + + spin_lock_irqsave(&kirkwood_pcie_lock, flags); + ret = orion_pcie_wr_conf(PCIE_BASE, bus, devfn, where, size, val); + spin_unlock_irqrestore(&kirkwood_pcie_lock, flags); + + return ret; +} + +static struct pci_ops pcie_ops = { + .read = pcie_rd_conf, + .write = pcie_wr_conf, +}; + + +static int kirkwood_pcie_setup(int nr, struct pci_sys_data *sys) +{ + struct resource *res; + + /* + * Generic PCIe unit setup. + */ + orion_pcie_setup(PCIE_BASE, &kirkwood_mbus_dram_info); + + /* + * Request resources. + */ + res = kzalloc(sizeof(struct resource) * 2, GFP_KERNEL); + if (!res) + panic("pcie_setup unable to alloc resources"); + + /* + * IORESOURCE_IO + */ + res[0].name = "PCIe I/O Space"; + res[0].flags = IORESOURCE_IO; + res[0].start = KIRKWOOD_PCIE_IO_PHYS_BASE; + res[0].end = res[0].start + KIRKWOOD_PCIE_IO_SIZE - 1; + if (request_resource(&ioport_resource, &res[0])) + panic("Request PCIe IO resource failed\n"); + sys->resource[0] = &res[0]; + + /* + * IORESOURCE_MEM + */ + res[1].name = "PCIe Memory Space"; + res[1].flags = IORESOURCE_MEM; + res[1].start = KIRKWOOD_PCIE_MEM_PHYS_BASE; + res[1].end = res[1].start + KIRKWOOD_PCIE_MEM_SIZE - 1; + if (request_resource(&iomem_resource, &res[1])) + panic("Request PCIe Memory resource failed\n"); + sys->resource[1] = &res[1]; + + sys->resource[2] = NULL; + sys->io_offset = 0; + + return 1; +} + +static void __devinit rc_pci_fixup(struct pci_dev *dev) +{ + /* + * Prevent enumeration of root complex. + */ + if (dev->bus->parent == NULL && dev->devfn == 0) { + int i; + + for (i = 0; i < DEVICE_COUNT_RESOURCE; i++) { + dev->resource[i].start = 0; + dev->resource[i].end = 0; + dev->resource[i].flags = 0; + } + } +} +DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_MARVELL, PCI_ANY_ID, rc_pci_fixup); + +static struct pci_bus __init * +kirkwood_pcie_scan_bus(int nr, struct pci_sys_data *sys) +{ + struct pci_bus *bus; + + if (nr == 0) { + bus = pci_scan_bus(sys->busnr, &pcie_ops, sys); + } else { + bus = NULL; + BUG(); + } + + return bus; +} + +static int __init kirkwood_pcie_map_irq(struct pci_dev *dev, u8 slot, u8 pin) +{ + return IRQ_KIRKWOOD_PCIE; +} + +static struct hw_pci kirkwood_pci __initdata = { + .nr_controllers = 1, + .swizzle = pci_std_swizzle, + .setup = kirkwood_pcie_setup, + .scan = kirkwood_pcie_scan_bus, + .map_irq = kirkwood_pcie_map_irq, +}; + +void __init kirkwood_pcie_init(void) +{ + pci_common_init(&kirkwood_pci); +} diff --git a/arch/arm/mach-kirkwood/rd88f6192-nas-setup.c b/arch/arm/mach-kirkwood/rd88f6192-nas-setup.c new file mode 100644 index 00000000000..6cf642c504d --- /dev/null +++ b/arch/arm/mach-kirkwood/rd88f6192-nas-setup.c @@ -0,0 +1,69 @@ +/* + * arch/arm/mach-kirkwood/rd88f6192-nas-setup.c + * + * Marvell RD-88F6192-NAS Reference Board Setup + * + * This file is licensed under the terms of the GNU General Public + * License version 2. This program is licensed "as is" without any + * warranty of any kind, whether express or implied. + */ + +#include <linux/kernel.h> +#include <linux/init.h> +#include <linux/platform_device.h> +#include <linux/pci.h> +#include <linux/irq.h> +#include <linux/mtd/physmap.h> +#include <linux/mtd/nand.h> +#include <linux/timer.h> +#include <linux/ata_platform.h> +#include <linux/mv643xx_eth.h> +#include <asm/mach-types.h> +#include <asm/mach/arch.h> +#include <asm/mach/pci.h> +#include <asm/arch/kirkwood.h> +#include "common.h" + +#define RD88F6192_GPIO_USB_VBUS 10 + +static struct mv643xx_eth_platform_data rd88f6192_ge00_data = { + .phy_addr = 8, +}; + +static struct mv_sata_platform_data rd88f6192_sata_data = { + .n_ports = 2, +}; + +static void __init rd88f6192_init(void) +{ + /* + * Basic setup. Needs to be called early. + */ + kirkwood_init(); + + kirkwood_ehci_init(); + kirkwood_ge00_init(&rd88f6192_ge00_data); + kirkwood_rtc_init(); + kirkwood_sata_init(&rd88f6192_sata_data); + kirkwood_uart0_init(); +} + +static int __init rd88f6192_pci_init(void) +{ + if (machine_is_rd88f6192_nas()) + kirkwood_pcie_init(); + + return 0; +} +subsys_initcall(rd88f6192_pci_init); + +MACHINE_START(RD88F6192_NAS, "Marvell RD-88F6192-NAS Development Board") + /* Maintainer: Saeed Bishara <saeed@marvell.com> */ + .phys_io = KIRKWOOD_REGS_PHYS_BASE, + .io_pg_offst = ((KIRKWOOD_REGS_VIRT_BASE) >> 18) & 0xfffc, + .boot_params = 0x00000100, + .init_machine = rd88f6192_init, + .map_io = kirkwood_map_io, + .init_irq = kirkwood_init_irq, + .timer = &kirkwood_timer, +MACHINE_END diff --git a/arch/arm/mach-kirkwood/rd88f6281-setup.c b/arch/arm/mach-kirkwood/rd88f6281-setup.c new file mode 100644 index 00000000000..e1f8de2c74a --- /dev/null +++ b/arch/arm/mach-kirkwood/rd88f6281-setup.c @@ -0,0 +1,113 @@ +/* + * arch/arm/mach-kirkwood/rd88f6281-setup.c + * + * Marvell RD-88F6281 Reference Board Setup + * + * This file is licensed under the terms of the GNU General Public + * License version 2. This program is licensed "as is" without any + * warranty of any kind, whether express or implied. + */ + +#include <linux/kernel.h> +#include <linux/init.h> +#include <linux/platform_device.h> +#include <linux/pci.h> +#include <linux/irq.h> +#include <linux/mtd/physmap.h> +#include <linux/mtd/nand.h> +#include <linux/timer.h> +#include <linux/ata_platform.h> +#include <linux/mv643xx_eth.h> +#include <asm/mach-types.h> +#include <asm/mach/arch.h> +#include <asm/mach/pci.h> +#include <asm/arch/kirkwood.h> +#include <asm/plat-orion/orion_nand.h> +#include "common.h" + +static struct mtd_partition rd88f6281_nand_parts[] = { + { + .name = "u-boot", + .offset = 0, + .size = SZ_1M + }, { + .name = "uImage", + .offset = MTDPART_OFS_NXTBLK, + .size = SZ_2M + }, { + .name = "root", + .offset = MTDPART_OFS_NXTBLK, + .size = MTDPART_SIZ_FULL + }, +}; + +static struct resource rd88f6281_nand_resource = { + .flags = IORESOURCE_MEM, + .start = KIRKWOOD_NAND_MEM_PHYS_BASE, + .end = KIRKWOOD_NAND_MEM_PHYS_BASE + + KIRKWOOD_NAND_MEM_SIZE - 1, +}; + +static struct orion_nand_data rd88f6281_nand_data = { + .parts = rd88f6281_nand_parts, + .nr_parts = ARRAY_SIZE(rd88f6281_nand_parts), + .cle = 0, + .ale = 1, + .width = 8, + .chip_delay = 25, +}; + +static struct platform_device rd88f6281_nand_flash = { + .name = "orion_nand", + .id = -1, + .dev = { + .platform_data = &rd88f6281_nand_data, + }, + .resource = &rd88f6281_nand_resource, + .num_resources = 1, +}; + +static struct mv643xx_eth_platform_data rd88f6281_ge00_data = { + .phy_addr = -1, +}; + +static struct mv_sata_platform_data rd88f6281_sata_data = { + .n_ports = 2, +}; + +static void __init rd88f6281_init(void) +{ + /* + * Basic setup. Needs to be called early. + */ + kirkwood_init(); + + kirkwood_ehci_init(); + kirkwood_ge00_init(&rd88f6281_ge00_data); + kirkwood_rtc_init(); + kirkwood_sata_init(&rd88f6281_sata_data); + kirkwood_uart0_init(); + kirkwood_uart1_init(); + + platform_device_register(&rd88f6281_nand_flash); +} + +static int __init rd88f6281_pci_init(void) +{ + if (machine_is_rd88f6281()) + kirkwood_pcie_init(); + + return 0; +} +subsys_initcall(rd88f6281_pci_init); + +MACHINE_START(RD88F6281, "Marvell RD-88F6281 Reference Board") + /* Maintainer: Saeed Bishara <saeed@marvell.com> */ + .phys_io = KIRKWOOD_REGS_PHYS_BASE, + .io_pg_offst = ((KIRKWOOD_REGS_VIRT_BASE) >> 18) & 0xfffc, + .boot_params = 0x00000100, + .init_machine = rd88f6281_init, + .map_io = kirkwood_map_io, + .init_irq = kirkwood_init_irq, + .timer = &kirkwood_timer, +MACHINE_END diff --git a/arch/arm/mach-loki/Kconfig b/arch/arm/mach-loki/Kconfig new file mode 100644 index 00000000000..0045bdd761c --- /dev/null +++ b/arch/arm/mach-loki/Kconfig @@ -0,0 +1,13 @@ +if ARCH_LOKI + +menu "Marvell Loki (88RC8480) Implementations" + +config MACH_LB88RC8480 + bool "Marvell LB88RC8480 Development Board" + help + Say 'Y' here if you want your kernel to support the + Marvell LB88RC8480 Development Board. + +endmenu + +endif diff --git a/arch/arm/mach-loki/Makefile b/arch/arm/mach-loki/Makefile new file mode 100644 index 00000000000..d43233ee590 --- /dev/null +++ b/arch/arm/mach-loki/Makefile @@ -0,0 +1,3 @@ +obj-y += common.o addr-map.o irq.o + +obj-$(CONFIG_MACH_LB88RC8480) += lb88rc8480-setup.o diff --git a/arch/arm/mach-loki/Makefile.boot b/arch/arm/mach-loki/Makefile.boot new file mode 100644 index 00000000000..67039c3e0c4 --- /dev/null +++ b/arch/arm/mach-loki/Makefile.boot @@ -0,0 +1,3 @@ + zreladdr-y := 0x00008000 +params_phys-y := 0x00000100 +initrd_phys-y := 0x00800000 diff --git a/arch/arm/mach-loki/addr-map.c b/arch/arm/mach-loki/addr-map.c new file mode 100644 index 00000000000..ba25e56ade5 --- /dev/null +++ b/arch/arm/mach-loki/addr-map.c @@ -0,0 +1,121 @@ +/* + * arch/arm/mach-loki/addr-map.c + * + * Address map functions for Marvell Loki (88RC8480) SoCs + * + * This file is licensed under the terms of the GNU General Public + * License version 2. This program is licensed "as is" without any + * warranty of any kind, whether express or implied. + */ + +#include <linux/kernel.h> +#include <linux/init.h> +#include <linux/mbus.h> +#include <asm/hardware.h> +#include <asm/io.h> +#include "common.h" + +/* + * Generic Address Decode Windows bit settings + */ +#define TARGET_DDR 0 +#define TARGET_DEV_BUS 1 +#define TARGET_PCIE0 3 +#define TARGET_PCIE1 4 +#define ATTR_DEV_BOOT 0x0f +#define ATTR_DEV_CS2 0x1b +#define ATTR_DEV_CS1 0x1d +#define ATTR_DEV_CS0 0x1e +#define ATTR_PCIE_IO 0x51 +#define ATTR_PCIE_MEM 0x59 + +/* + * Helpers to get DDR bank info + */ +#define DDR_SIZE_CS(n) DDR_REG(0x1500 + ((n) << 3)) +#define DDR_BASE_CS(n) DDR_REG(0x1504 + ((n) << 3)) + +/* + * CPU Address Decode Windows registers + */ +#define CPU_WIN_CTRL(n) BRIDGE_REG(0x000 | ((n) << 4)) +#define CPU_WIN_BASE(n) BRIDGE_REG(0x004 | ((n) << 4)) +#define CPU_WIN_REMAP_LO(n) BRIDGE_REG(0x008 | ((n) << 4)) +#define CPU_WIN_REMAP_HI(n) BRIDGE_REG(0x00c | ((n) << 4)) + + +struct mbus_dram_target_info loki_mbus_dram_info; + +static void __init setup_cpu_win(int win, u32 base, u32 size, + u8 target, u8 attr, int remap) +{ + u32 ctrl; + + base &= 0xffff0000; + ctrl = ((size - 1) & 0xffff0000) | (attr << 8) | (1 << 5) | target; + + writel(base, CPU_WIN_BASE(win)); + writel(ctrl, CPU_WIN_CTRL(win)); + if (win < 2) { + if (remap < 0) + remap = base; + + writel(remap & 0xffff0000, CPU_WIN_REMAP_LO(win)); + writel(0, CPU_WIN_REMAP_HI(win)); + } +} + +void __init loki_setup_cpu_mbus(void) +{ + int i; + int cs; + + /* + * First, disable and clear windows. + */ + for (i = 0; i < 8; i++) { + writel(0, CPU_WIN_BASE(i)); + writel(0, CPU_WIN_CTRL(i)); + if (i < 2) { + writel(0, CPU_WIN_REMAP_LO(i)); + writel(0, CPU_WIN_REMAP_HI(i)); + } + } + + /* + * Setup windows for PCIe IO+MEM space. + */ + setup_cpu_win(2, LOKI_PCIE0_MEM_PHYS_BASE, LOKI_PCIE0_MEM_SIZE, + TARGET_PCIE0, ATTR_PCIE_MEM, -1); + setup_cpu_win(3, LOKI_PCIE1_MEM_PHYS_BASE, LOKI_PCIE1_MEM_SIZE, + TARGET_PCIE1, ATTR_PCIE_MEM, -1); + + /* + * Setup MBUS dram target info. + */ + loki_mbus_dram_info.mbus_dram_target_id = TARGET_DDR; + + for (i = 0, cs = 0; i < 4; i++) { + u32 base = readl(DDR_BASE_CS(i)); + u32 size = readl(DDR_SIZE_CS(i)); + + /* + * Chip select enabled? + */ + if (size & 1) { + struct mbus_dram_window *w; + + w = &loki_mbus_dram_info.cs[cs++]; + w->cs_index = i; + w->mbus_attr = 0xf & ~(1 << i); + w->base = base & 0xffff0000; + w->size = (size | 0x0000ffff) + 1; + } + } + loki_mbus_dram_info.num_cs = cs; +} + +void __init loki_setup_dev_boot_win(u32 base, u32 size) +{ + setup_cpu_win(4, base, size, TARGET_DEV_BUS, ATTR_DEV_BOOT, -1); +} diff --git a/arch/arm/mach-loki/common.c b/arch/arm/mach-loki/common.c new file mode 100644 index 00000000000..410f50399dd --- /dev/null +++ b/arch/arm/mach-loki/common.c @@ -0,0 +1,305 @@ +/* + * arch/arm/mach-loki/common.c + * + * Core functions for Marvell Loki (88RC8480) SoCs + * + * This file is licensed under the terms of the GNU General Public + * License version 2. This program is licensed "as is" without any + * warranty of any kind, whether express or implied. + */ + +#include <linux/kernel.h> +#include <linux/init.h> +#include <linux/platform_device.h> +#include <linux/serial_8250.h> +#include <linux/mbus.h> +#include <linux/mv643xx_eth.h> +#include <asm/page.h> +#include <asm/timex.h> +#include <asm/mach/map.h> +#include <asm/mach/time.h> +#include <asm/arch/loki.h> +#include <asm/plat-orion/orion_nand.h> +#include <asm/plat-orion/time.h> +#include "common.h" + +/***************************************************************************** + * I/O Address Mapping + ****************************************************************************/ +static struct map_desc loki_io_desc[] __initdata = { + { + .virtual = LOKI_REGS_VIRT_BASE, + .pfn = __phys_to_pfn(LOKI_REGS_PHYS_BASE), + .length = LOKI_REGS_SIZE, + .type = MT_DEVICE, + }, +}; + +void __init loki_map_io(void) +{ + iotable_init(loki_io_desc, ARRAY_SIZE(loki_io_desc)); +} + + +/***************************************************************************** + * GE0 + ****************************************************************************/ +struct mv643xx_eth_shared_platform_data loki_ge0_shared_data = { + .t_clk = LOKI_TCLK, + .dram = &loki_mbus_dram_info, +}; + +static struct resource loki_ge0_shared_resources[] = { + { + .name = "ge0 base", + .start = GE0_PHYS_BASE + 0x2000, + .end = GE0_PHYS_BASE + 0x3fff, + .flags = IORESOURCE_MEM, + }, +}; + +static struct platform_device loki_ge0_shared = { + .name = MV643XX_ETH_SHARED_NAME, + .id = 0, + .dev = { + .platform_data = &loki_ge0_shared_data, + }, + .num_resources = 1, + .resource = loki_ge0_shared_resources, +}; + +static struct resource loki_ge0_resources[] = { + { + .name = "ge0 irq", + .start = IRQ_LOKI_GBE_A_INT, + .end = IRQ_LOKI_GBE_A_INT, + .flags = IORESOURCE_IRQ, + }, +}; + +static struct platform_device loki_ge0 = { + .name = MV643XX_ETH_NAME, + .id = 0, + .num_resources = 1, + .resource = loki_ge0_resources, +}; + +void __init loki_ge0_init(struct mv643xx_eth_platform_data *eth_data) +{ + eth_data->shared = &loki_ge0_shared; + loki_ge0.dev.platform_data = eth_data; + + writel(0x00079220, GE0_VIRT_BASE + 0x20b0); + platform_device_register(&loki_ge0_shared); + platform_device_register(&loki_ge0); +} + + +/***************************************************************************** + * GE1 + ****************************************************************************/ +struct mv643xx_eth_shared_platform_data loki_ge1_shared_data = { + .t_clk = LOKI_TCLK, + .dram = &loki_mbus_dram_info, +}; + +static struct resource loki_ge1_shared_resources[] = { + { + .name = "ge1 base", + .start = GE1_PHYS_BASE + 0x2000, + .end = GE1_PHYS_BASE + 0x3fff, + .flags = IORESOURCE_MEM, + }, +}; + +static struct platform_device loki_ge1_shared = { + .name = MV643XX_ETH_SHARED_NAME, + .id = 1, + .dev = { + .platform_data = &loki_ge1_shared_data, + }, + .num_resources = 1, + .resource = loki_ge1_shared_resources, +}; + +static struct resource loki_ge1_resources[] = { + { + .name = "ge1 irq", + .start = IRQ_LOKI_GBE_B_INT, + .end = IRQ_LOKI_GBE_B_INT, + .flags = IORESOURCE_IRQ, + }, +}; + +static struct platform_device loki_ge1 = { + .name = MV643XX_ETH_NAME, + .id = 1, + .num_resources = 1, + .resource = loki_ge1_resources, +}; + +void __init loki_ge1_init(struct mv643xx_eth_platform_data *eth_data) +{ + eth_data->shared = &loki_ge1_shared; + loki_ge1.dev.platform_data = eth_data; + + writel(0x00079220, GE1_VIRT_BASE + 0x20b0); + platform_device_register(&loki_ge1_shared); + platform_device_register(&loki_ge1); +} + + +/***************************************************************************** + * SAS/SATA + ****************************************************************************/ +static struct resource loki_sas_resources[] = { + { + .name = "mvsas0 mem", + .start = SAS0_PHYS_BASE, + .end = SAS0_PHYS_BASE + 0x01ff, + .flags = IORESOURCE_MEM, + }, { + .name = "mvsas0 irq", + .start = IRQ_LOKI_SAS_A, + .end = IRQ_LOKI_SAS_A, + .flags = IORESOURCE_IRQ, + }, { + .name = "mvsas1 mem", + .start = SAS1_PHYS_BASE, + .end = SAS1_PHYS_BASE + 0x01ff, + .flags = IORESOURCE_MEM, + }, { + .name = "mvsas1 irq", + .start = IRQ_LOKI_SAS_B, + .end = IRQ_LOKI_SAS_B, + .flags = IORESOURCE_IRQ, + }, +}; + +static struct platform_device loki_sas = { + .name = "mvsas", + .id = 0, + .dev = { + .coherent_dma_mask = 0xffffffff, + }, + .num_resources = ARRAY_SIZE(loki_sas_resources), + .resource = loki_sas_resources, +}; + +void __init loki_sas_init(void) +{ + writel(0x8300f707, DDR_REG(0x1424)); + platform_device_register(&loki_sas); +} + + +/***************************************************************************** + * UART0 + ****************************************************************************/ +static struct plat_serial8250_port loki_uart0_data[] = { + { + .mapbase = UART0_PHYS_BASE, + .membase = (char *)UART0_VIRT_BASE, + .irq = IRQ_LOKI_UART0, + .flags = UPF_SKIP_TEST | UPF_BOOT_AUTOCONF, + .iotype = UPIO_MEM, + .regshift = 2, + .uartclk = LOKI_TCLK, + }, { + }, +}; + +static struct resource loki_uart0_resources[] = { + { + .start = UART0_PHYS_BASE, + .end = UART0_PHYS_BASE + 0xff, + .flags = IORESOURCE_MEM, + }, { + .start = IRQ_LOKI_UART0, + .end = IRQ_LOKI_UART0, + .flags = IORESOURCE_IRQ, + }, +}; + +static struct platform_device loki_uart0 = { + .name = "serial8250", + .id = 0, + .dev = { + .platform_data = loki_uart0_data, + }, + .resource = loki_uart0_resources, + .num_resources = ARRAY_SIZE(loki_uart0_resources), +}; + +void __init loki_uart0_init(void) +{ + platform_device_register(&loki_uart0); +} + + +/***************************************************************************** + * UART1 + ****************************************************************************/ +static struct plat_serial8250_port loki_uart1_data[] = { + { + .mapbase = UART1_PHYS_BASE, + .membase = (char *)UART1_VIRT_BASE, + .irq = IRQ_LOKI_UART1, + .flags = UPF_SKIP_TEST | UPF_BOOT_AUTOCONF, + .iotype = UPIO_MEM, + .regshift = 2, + .uartclk = LOKI_TCLK, + }, { + }, +}; + +static struct resource loki_uart1_resources[] = { + { + .start = UART1_PHYS_BASE, + .end = UART1_PHYS_BASE + 0xff, + .flags = IORESOURCE_MEM, + }, { + .start = IRQ_LOKI_UART1, + .end = IRQ_LOKI_UART1, + .flags = IORESOURCE_IRQ, + }, +}; + +static struct platform_device loki_uart1 = { + .name = "serial8250", + .id = 1, + .dev = { + .platform_data = loki_uart1_data, + }, + .resource = loki_uart1_resources, + .num_resources = ARRAY_SIZE(loki_uart1_resources), +}; + +void __init loki_uart1_init(void) +{ + platform_device_register(&loki_uart1); +} + + +/***************************************************************************** + * Time handling + ****************************************************************************/ +static void loki_timer_init(void) +{ + orion_time_init(IRQ_LOKI_BRIDGE, LOKI_TCLK); +} + +struct sys_timer loki_timer = { + .init = loki_timer_init, +}; + + +/***************************************************************************** + * General + ****************************************************************************/ +void __init loki_init(void) +{ + printk(KERN_INFO "Loki ID: 88RC8480. TCLK=%d.\n", LOKI_TCLK); + + loki_setup_cpu_mbus(); +} diff --git a/arch/arm/mach-loki/common.h b/arch/arm/mach-loki/common.h new file mode 100644 index 00000000000..26054fd0f05 --- /dev/null +++ b/arch/arm/mach-loki/common.h @@ -0,0 +1,36 @@ +/* + * arch/arm/mach-loki/common.h + * + * Core functions for Marvell Loki (88RC8480) SoCs + * + * This file is licensed under the terms of the GNU General Public + * License version 2. This program is licensed "as is" without any + * warranty of any kind, whether express or implied. + */ + +#ifndef __ARCH_LOKI_COMMON_H +#define __ARCH_LOKI_COMMON_H + +struct mv643xx_eth_platform_data; + +/* + * Basic Loki init functions used early by machine-setup. + */ +void loki_map_io(void); +void loki_init(void); +void loki_init_irq(void); + +extern struct mbus_dram_target_info loki_mbus_dram_info; +void loki_setup_cpu_mbus(void); +void loki_setup_dev_boot_win(u32 base, u32 size); + +void loki_ge0_init(struct mv643xx_eth_platform_data *eth_data); +void loki_ge1_init(struct mv643xx_eth_platform_data *eth_data); +void loki_sas_init(void); +void loki_uart0_init(void); +void loki_uart1_init(void); + +extern struct sys_timer loki_timer; + + +#endif diff --git a/arch/arm/mach-loki/irq.c b/arch/arm/mach-loki/irq.c new file mode 100644 index 00000000000..d839af91fe0 --- /dev/null +++ b/arch/arm/mach-loki/irq.c @@ -0,0 +1,21 @@ +/* + * arch/arm/mach-loki/irq.c + * + * Marvell Loki (88RC8480) IRQ handling. + * + * This file is licensed under the terms of the GNU General Public + * License version 2. This program is licensed "as is" without any + * warranty of any kind, whether express or implied. + */ + +#include <linux/kernel.h> +#include <linux/init.h> +#include <linux/irq.h> +#include <asm/io.h> +#include <asm/plat-orion/irq.h> +#include "common.h" + +void __init loki_init_irq(void) +{ + orion_irq_init(0, (void __iomem *)(IRQ_VIRT_BASE + IRQ_MASK_OFF)); +} diff --git a/arch/arm/mach-loki/lb88rc8480-setup.c b/arch/arm/mach-loki/lb88rc8480-setup.c new file mode 100644 index 00000000000..d1b9e6e6253 --- /dev/null +++ b/arch/arm/mach-loki/lb88rc8480-setup.c @@ -0,0 +1,100 @@ +/* + * arch/arm/mach-loki/lb88rc8480-setup.c + * + * Marvell LB88RC8480 Development Board Setup + * + * This file is licensed under the terms of the GNU General Public + * License version 2. This program is licensed "as is" without any + * warranty of any kind, whether express or implied. + */ + +#include <linux/kernel.h> +#include <linux/init.h> +#include <linux/platform_device.h> +#include <linux/irq.h> +#include <linux/mtd/physmap.h> +#include <linux/mtd/nand.h> +#include <linux/timer.h> +#include <linux/ata_platform.h> +#include <linux/mv643xx_eth.h> +#include <asm/mach-types.h> +#include <asm/mach/arch.h> +#include <asm/arch/loki.h> +#include "common.h" + +#define LB88RC8480_FLASH_BOOT_CS_BASE 0xf8000000 +#define LB88RC8480_FLASH_BOOT_CS_SIZE SZ_128M + +#define LB88RC8480_NOR_BOOT_BASE 0xff000000 +#define LB88RC8480_NOR_BOOT_SIZE SZ_16M + +static struct mtd_partition lb88rc8480_boot_flash_parts[] = { + { + .name = "kernel", + .offset = 0, + .size = SZ_2M, + }, { + .name = "root-fs", + .offset = SZ_2M, + .size = (SZ_8M + SZ_4M + SZ_1M), + }, { + .name = "u-boot", + .offset = (SZ_8M + SZ_4M + SZ_2M + SZ_1M), + .size = SZ_1M, + }, +}; + +static struct physmap_flash_data lb88rc8480_boot_flash_data = { + .parts = lb88rc8480_boot_flash_parts, + .nr_parts = ARRAY_SIZE(lb88rc8480_boot_flash_parts), + .width = 1, /* 8 bit bus width */ +}; + +static struct resource lb88rc8480_boot_flash_resource = { + .flags = IORESOURCE_MEM, + .start = LB88RC8480_NOR_BOOT_BASE, + .end = LB88RC8480_NOR_BOOT_BASE + LB88RC8480_NOR_BOOT_SIZE - 1, +}; + +static struct platform_device lb88rc8480_boot_flash = { + .name = "physmap-flash", + .id = 0, + .dev = { + .platform_data = &lb88rc8480_boot_flash_data, + }, + .num_resources = 1, + .resource = &lb88rc8480_boot_flash_resource, +}; + +static struct mv643xx_eth_platform_data lb88rc8480_ge0_data = { + .phy_addr = 1, + .mac_addr = { 0x00, 0x50, 0x43, 0x11, 0x22, 0x33 }, +}; + +static void __init lb88rc8480_init(void) +{ + /* + * Basic setup. Needs to be called early. + */ + loki_init(); + + loki_ge0_init(&lb88rc8480_ge0_data); + loki_sas_init(); + loki_uart0_init(); + loki_uart1_init(); + + loki_setup_dev_boot_win(LB88RC8480_FLASH_BOOT_CS_BASE, + LB88RC8480_FLASH_BOOT_CS_SIZE); + platform_device_register(&lb88rc8480_boot_flash); +} + +MACHINE_START(LB88RC8480, "Marvell LB88RC8480 Development Board") + /* Maintainer: Ke Wei <kewei@marvell.com> */ + .phys_io = LOKI_REGS_PHYS_BASE, + .io_pg_offst = ((LOKI_REGS_VIRT_BASE) >> 18) & 0xfffc, + .boot_params = 0x00000100, + .init_machine = lb88rc8480_init, + .map_io = loki_map_io, + .init_irq = loki_init_irq, + .timer = &loki_timer, +MACHINE_END diff --git a/arch/arm/mach-mv78xx0/Kconfig b/arch/arm/mach-mv78xx0/Kconfig new file mode 100644 index 00000000000..d83cb86837d --- /dev/null +++ b/arch/arm/mach-mv78xx0/Kconfig @@ -0,0 +1,13 @@ +if ARCH_MV78XX0 + +menu "Marvell MV78xx0 Implementations" + +config MACH_DB78X00_BP + bool "Marvell DB-78x00-BP Development Board" + help + Say 'Y' here if you want your kernel to support the + Marvell DB-78x00-BP Development Board. + +endmenu + +endif diff --git a/arch/arm/mach-mv78xx0/Makefile b/arch/arm/mach-mv78xx0/Makefile new file mode 100644 index 00000000000..ec16c05c3b1 --- /dev/null +++ b/arch/arm/mach-mv78xx0/Makefile @@ -0,0 +1,2 @@ +obj-y += common.o addr-map.o irq.o pcie.o +obj-$(CONFIG_MACH_DB78X00_BP) += db78x00-bp-setup.o diff --git a/arch/arm/mach-mv78xx0/Makefile.boot b/arch/arm/mach-mv78xx0/Makefile.boot new file mode 100644 index 00000000000..67039c3e0c4 --- /dev/null +++ b/arch/arm/mach-mv78xx0/Makefile.boot @@ -0,0 +1,3 @@ + zreladdr-y := 0x00008000 +params_phys-y := 0x00000100 +initrd_phys-y := 0x00800000 diff --git a/arch/arm/mach-mv78xx0/addr-map.c b/arch/arm/mach-mv78xx0/addr-map.c new file mode 100644 index 00000000000..4004b672a2e --- /dev/null +++ b/arch/arm/mach-mv78xx0/addr-map.c @@ -0,0 +1,156 @@ +/* + * arch/arm/mach-mv78xx0/addr-map.c + * + * Address map functions for Marvell MV78xx0 SoCs + * + * This file is licensed under the terms of the GNU General Public + * License version 2. This program is licensed "as is" without any + * warranty of any kind, whether express or implied. + */ + +#include <linux/kernel.h> +#include <linux/init.h> +#include <linux/mbus.h> +#include <asm/io.h> +#include "common.h" + +/* + * Generic Address Decode Windows bit settings + */ +#define TARGET_DDR 0 +#define TARGET_DEV_BUS 1 +#define TARGET_PCIE0 4 +#define TARGET_PCIE1 8 +#define TARGET_PCIE(i) ((i) ? TARGET_PCIE1 : TARGET_PCIE0) +#define ATTR_DEV_SPI_ROM 0x1f +#define ATTR_DEV_BOOT 0x2f +#define ATTR_DEV_CS3 0x37 +#define ATTR_DEV_CS2 0x3b +#define ATTR_DEV_CS1 0x3d +#define ATTR_DEV_CS0 0x3e +#define ATTR_PCIE_IO(l) (0xf0 & ~(0x10 << (l))) +#define ATTR_PCIE_MEM(l) (0xf8 & ~(0x10 << (l))) + +/* + * Helpers to get DDR bank info + */ +#define DDR_BASE_CS_OFF(n) (0x0000 + ((n) << 3)) +#define DDR_SIZE_CS_OFF(n) (0x0004 + ((n) << 3)) + +/* + * CPU Address Decode Windows registers + */ +#define WIN0_OFF(n) (BRIDGE_VIRT_BASE + 0x0000 + ((n) << 4)) +#define WIN8_OFF(n) (BRIDGE_VIRT_BASE + 0x0900 + (((n) - 8) << 4)) +#define WIN_CTRL_OFF 0x0000 +#define WIN_BASE_OFF 0x0004 +#define WIN_REMAP_LO_OFF 0x0008 +#define WIN_REMAP_HI_OFF 0x000c + + +struct mbus_dram_target_info mv78xx0_mbus_dram_info; + +static void __init __iomem *win_cfg_base(int win) +{ + /* + * Find the control register base address for this window. + * + * BRIDGE_VIRT_BASE points to the right (CPU0's or CPU1's) + * MBUS bridge depending on which CPU core we're running on, + * so we don't need to take that into account here. + */ + + return (void __iomem *)((win < 8) ? WIN0_OFF(win) : WIN8_OFF(win)); +} + +static int __init cpu_win_can_remap(int win) +{ + if (win < 8) + return 1; + + return 0; +} + +static void __init setup_cpu_win(int win, u32 base, u32 size, + u8 target, u8 attr, int remap) +{ + void __iomem *addr = win_cfg_base(win); + u32 ctrl; + + base &= 0xffff0000; + ctrl = ((size - 1) & 0xffff0000) | (attr << 8) | (target << 4) | 1; + + writel(base, addr + WIN_BASE_OFF); + writel(ctrl, addr + WIN_CTRL_OFF); + if (cpu_win_can_remap(win)) { + if (remap < 0) + remap = base; + + writel(remap & 0xffff0000, addr + WIN_REMAP_LO_OFF); + writel(0, addr + WIN_REMAP_HI_OFF); + } +} + +void __init mv78xx0_setup_cpu_mbus(void) +{ + void __iomem *addr; + int i; + int cs; + + /* + * First, disable and clear windows. + */ + for (i = 0; i < 14; i++) { + addr = win_cfg_base(i); + + writel(0, addr + WIN_BASE_OFF); + writel(0, addr + WIN_CTRL_OFF); + if (cpu_win_can_remap(i)) { + writel(0, addr + WIN_REMAP_LO_OFF); + writel(0, addr + WIN_REMAP_HI_OFF); + } + } + + /* + * Setup MBUS dram target info. + */ + mv78xx0_mbus_dram_info.mbus_dram_target_id = TARGET_DDR; + + if (mv78xx0_core_index() == 0) + addr = (void __iomem *)DDR_WINDOW_CPU0_BASE; + else + addr = (void __iomem *)DDR_WINDOW_CPU1_BASE; + + for (i = 0, cs = 0; i < 4; i++) { + u32 base = readl(addr + DDR_BASE_CS_OFF(i)); + u32 size = readl(addr + DDR_SIZE_CS_OFF(i)); + + /* + * Chip select enabled? + */ + if (size & 1) { + struct mbus_dram_window *w; + + w = &mv78xx0_mbus_dram_info.cs[cs++]; + w->cs_index = i; + w->mbus_attr = 0xf & ~(1 << i); + w->base = base & 0xffff0000; + w->size = (size | 0x0000ffff) + 1; + } + } + mv78xx0_mbus_dram_info.num_cs = cs; +} + +void __init mv78xx0_setup_pcie_io_win(int window, u32 base, u32 size, + int maj, int min) +{ + setup_cpu_win(window, base, size, TARGET_PCIE(maj), + ATTR_PCIE_IO(min), -1); +} + +void __init mv78xx0_setup_pcie_mem_win(int window, u32 base, u32 size, + int maj, int min) +{ + setup_cpu_win(window, base, size, TARGET_PCIE(maj), + ATTR_PCIE_MEM(min), -1); +} diff --git a/arch/arm/mach-mv78xx0/common.c b/arch/arm/mach-mv78xx0/common.c new file mode 100644 index 00000000000..d27b83b7bf6 --- /dev/null +++ b/arch/arm/mach-mv78xx0/common.c @@ -0,0 +1,754 @@ +/* + * arch/arm/mach-mv78xx0/common.c + * + * Core functions for Marvell MV78xx0 SoCs + * + * This file is licensed under the terms of the GNU General Public + * License version 2. This program is licensed "as is" without any + * warranty of any kind, whether express or implied. + */ + +#include <linux/kernel.h> +#include <linux/init.h> +#include <linux/platform_device.h> +#include <linux/serial_8250.h> +#include <linux/mbus.h> +#include <linux/mv643xx_eth.h> +#include <linux/ata_platform.h> +#include <asm/mach/map.h> +#include <asm/mach/time.h> +#include <asm/arch/mv78xx0.h> +#include <asm/plat-orion/cache-feroceon-l2.h> +#include <asm/plat-orion/ehci-orion.h> +#include <asm/plat-orion/orion_nand.h> +#include <asm/plat-orion/time.h> +#include "common.h" + + +/***************************************************************************** + * Common bits + ****************************************************************************/ +int mv78xx0_core_index(void) +{ + u32 extra; + + /* + * Read Extra Features register. + */ + __asm__("mrc p15, 1, %0, c15, c1, 0" : "=r" (extra)); + + return !!(extra & 0x00004000); +} + +static int get_hclk(void) +{ + int hclk; + + /* + * HCLK tick rate is configured by DEV_D[7:5] pins. + */ + switch ((readl(SAMPLE_AT_RESET_LOW) >> 5) & 7) { + case 0: + hclk = 166666667; + break; + case 1: + hclk = 200000000; + break; + case 2: + hclk = 266666667; + break; + case 3: + hclk = 333333333; + break; + case 4: + hclk = 400000000; + break; + default: + panic("unknown HCLK PLL setting: %.8x\n", + readl(SAMPLE_AT_RESET_LOW)); + } + + return hclk; +} + +static void get_pclk_l2clk(int hclk, int core_index, int *pclk, int *l2clk) +{ + u32 cfg; + + /* + * Core #0 PCLK/L2CLK is configured by bits [13:8], core #1 + * PCLK/L2CLK by bits [19:14]. + */ + if (core_index == 0) { + cfg = (readl(SAMPLE_AT_RESET_LOW) >> 8) & 0x3f; + } else { + cfg = (readl(SAMPLE_AT_RESET_LOW) >> 14) & 0x3f; + } + + /* + * Bits [11:8] ([17:14] for core #1) configure the PCLK:HCLK + * ratio (1, 1.5, 2, 2.5, 3, 3.5, 4, 4.5, 5, 5.5, 6). + */ + *pclk = ((u64)hclk * (2 + (cfg & 0xf))) >> 1; + + /* + * Bits [13:12] ([19:18] for core #1) configure the PCLK:L2CLK + * ratio (1, 2, 3). + */ + *l2clk = *pclk / (((cfg >> 4) & 3) + 1); +} + +static int get_tclk(void) +{ + int tclk; + + /* + * TCLK tick rate is configured by DEV_A[2:0] strap pins. + */ + switch ((readl(SAMPLE_AT_RESET_HIGH) >> 6) & 7) { + case 1: + tclk = 166666667; + break; + case 3: + tclk = 200000000; + break; + default: + panic("unknown TCLK PLL setting: %.8x\n", + readl(SAMPLE_AT_RESET_HIGH)); + } + + return tclk; +} + + +/***************************************************************************** + * I/O Address Mapping + ****************************************************************************/ +static struct map_desc mv78xx0_io_desc[] __initdata = { + { + .virtual = MV78XX0_CORE_REGS_VIRT_BASE, + .pfn = 0, + .length = MV78XX0_CORE_REGS_SIZE, + .type = MT_DEVICE, + }, { + .virtual = MV78XX0_PCIE_IO_VIRT_BASE(0), + .pfn = __phys_to_pfn(MV78XX0_PCIE_IO_PHYS_BASE(0)), + .length = MV78XX0_PCIE_IO_SIZE * 8, + .type = MT_DEVICE, + }, { + .virtual = MV78XX0_REGS_VIRT_BASE, + .pfn = __phys_to_pfn(MV78XX0_REGS_PHYS_BASE), + .length = MV78XX0_REGS_SIZE, + .type = MT_DEVICE, + }, +}; + +void __init mv78xx0_map_io(void) +{ + unsigned long phys; + + /* + * Map the right set of per-core registers depending on + * which core we are running on. + */ + if (mv78xx0_core_index() == 0) { + phys = MV78XX0_CORE0_REGS_PHYS_BASE; + } else { + phys = MV78XX0_CORE1_REGS_PHYS_BASE; + } + mv78xx0_io_desc[0].pfn = __phys_to_pfn(phys); + + iotable_init(mv78xx0_io_desc, ARRAY_SIZE(mv78xx0_io_desc)); +} + + +/***************************************************************************** + * EHCI + ****************************************************************************/ +static struct orion_ehci_data mv78xx0_ehci_data = { + .dram = &mv78xx0_mbus_dram_info, +}; + +static u64 ehci_dmamask = 0xffffffffUL; + + +/***************************************************************************** + * EHCI0 + ****************************************************************************/ +static struct resource mv78xx0_ehci0_resources[] = { + { + .start = USB0_PHYS_BASE, + .end = USB0_PHYS_BASE + 0x0fff, + .flags = IORESOURCE_MEM, + }, { + .start = IRQ_MV78XX0_USB_0, + .end = IRQ_MV78XX0_USB_0, + .flags = IORESOURCE_IRQ, + }, +}; + +static struct platform_device mv78xx0_ehci0 = { + .name = "orion-ehci", + .id = 0, + .dev = { + .dma_mask = &ehci_dmamask, + .coherent_dma_mask = 0xffffffff, + .platform_data = &mv78xx0_ehci_data, + }, + .resource = mv78xx0_ehci0_resources, + .num_resources = ARRAY_SIZE(mv78xx0_ehci0_resources), +}; + +void __init mv78xx0_ehci0_init(void) +{ + platform_device_register(&mv78xx0_ehci0); +} + + +/***************************************************************************** + * EHCI1 + ****************************************************************************/ +static struct resource mv78xx0_ehci1_resources[] = { + { + .start = USB1_PHYS_BASE, + .end = USB1_PHYS_BASE + 0x0fff, + .flags = IORESOURCE_MEM, + }, { + .start = IRQ_MV78XX0_USB_1, + .end = IRQ_MV78XX0_USB_1, + .flags = IORESOURCE_IRQ, + }, +}; + +static struct platform_device mv78xx0_ehci1 = { + .name = "orion-ehci", + .id = 1, + .dev = { + .dma_mask = &ehci_dmamask, + .coherent_dma_mask = 0xffffffff, + .platform_data = &mv78xx0_ehci_data, + }, + .resource = mv78xx0_ehci1_resources, + .num_resources = ARRAY_SIZE(mv78xx0_ehci1_resources), +}; + +void __init mv78xx0_ehci1_init(void) +{ + platform_device_register(&mv78xx0_ehci1); +} + + +/***************************************************************************** + * EHCI2 + ****************************************************************************/ +static struct resource mv78xx0_ehci2_resources[] = { + { + .start = USB2_PHYS_BASE, + .end = USB2_PHYS_BASE + 0x0fff, + .flags = IORESOURCE_MEM, + }, { + .start = IRQ_MV78XX0_USB_2, + .end = IRQ_MV78XX0_USB_2, + .flags = IORESOURCE_IRQ, + }, +}; + +static struct platform_device mv78xx0_ehci2 = { + .name = "orion-ehci", + .id = 2, + .dev = { + .dma_mask = &ehci_dmamask, + .coherent_dma_mask = 0xffffffff, + .platform_data = &mv78xx0_ehci_data, + }, + .resource = mv78xx0_ehci2_resources, + .num_resources = ARRAY_SIZE(mv78xx0_ehci2_resources), +}; + +void __init mv78xx0_ehci2_init(void) +{ + platform_device_register(&mv78xx0_ehci2); +} + + +/***************************************************************************** + * GE00 + ****************************************************************************/ +struct mv643xx_eth_shared_platform_data mv78xx0_ge00_shared_data = { + .t_clk = 0, + .dram = &mv78xx0_mbus_dram_info, +}; + +static struct resource mv78xx0_ge00_shared_resources[] = { + { + .name = "ge00 base", + .start = GE00_PHYS_BASE + 0x2000, + .end = GE00_PHYS_BASE + 0x3fff, + .flags = IORESOURCE_MEM, + }, +}; + +static struct platform_device mv78xx0_ge00_shared = { + .name = MV643XX_ETH_SHARED_NAME, + .id = 0, + .dev = { + .platform_data = &mv78xx0_ge00_shared_data, + }, + .num_resources = 1, + .resource = mv78xx0_ge00_shared_resources, +}; + +static struct resource mv78xx0_ge00_resources[] = { + { + .name = "ge00 irq", + .start = IRQ_MV78XX0_GE00_SUM, + .end = IRQ_MV78XX0_GE00_SUM, + .flags = IORESOURCE_IRQ, + }, +}; + +static struct platform_device mv78xx0_ge00 = { + .name = MV643XX_ETH_NAME, + .id = 0, + .num_resources = 1, + .resource = mv78xx0_ge00_resources, +}; + +void __init mv78xx0_ge00_init(struct mv643xx_eth_platform_data *eth_data) +{ + eth_data->shared = &mv78xx0_ge00_shared; + mv78xx0_ge00.dev.platform_data = eth_data; + + platform_device_register(&mv78xx0_ge00_shared); + platform_device_register(&mv78xx0_ge00); +} + + +/***************************************************************************** + * GE01 + ****************************************************************************/ +struct mv643xx_eth_shared_platform_data mv78xx0_ge01_shared_data = { + .t_clk = 0, + .dram = &mv78xx0_mbus_dram_info, +}; + +static struct resource mv78xx0_ge01_shared_resources[] = { + { + .name = "ge01 base", + .start = GE01_PHYS_BASE + 0x2000, + .end = GE01_PHYS_BASE + 0x3fff, + .flags = IORESOURCE_MEM, + }, +}; + +static struct platform_device mv78xx0_ge01_shared = { + .name = MV643XX_ETH_SHARED_NAME, + .id = 1, + .dev = { + .platform_data = &mv78xx0_ge01_shared_data, + }, + .num_resources = 1, + .resource = mv78xx0_ge01_shared_resources, +}; + +static struct resource mv78xx0_ge01_resources[] = { + { + .name = "ge01 irq", + .start = IRQ_MV78XX0_GE01_SUM, + .end = IRQ_MV78XX0_GE01_SUM, + .flags = IORESOURCE_IRQ, + }, +}; + +static struct platform_device mv78xx0_ge01 = { + .name = MV643XX_ETH_NAME, + .id = 1, + .num_resources = 1, + .resource = mv78xx0_ge01_resources, +}; + +void __init mv78xx0_ge01_init(struct mv643xx_eth_platform_data *eth_data) +{ + eth_data->shared = &mv78xx0_ge01_shared; + eth_data->shared_smi = &mv78xx0_ge00_shared; + mv78xx0_ge01.dev.platform_data = eth_data; + + platform_device_register(&mv78xx0_ge01_shared); + platform_device_register(&mv78xx0_ge01); +} + + +/***************************************************************************** + * GE10 + ****************************************************************************/ +struct mv643xx_eth_shared_platform_data mv78xx0_ge10_shared_data = { + .t_clk = 0, + .dram = &mv78xx0_mbus_dram_info, +}; + +static struct resource mv78xx0_ge10_shared_resources[] = { + { + .name = "ge10 base", + .start = GE10_PHYS_BASE + 0x2000, + .end = GE10_PHYS_BASE + 0x3fff, + .flags = IORESOURCE_MEM, + }, +}; + +static struct platform_device mv78xx0_ge10_shared = { + .name = MV643XX_ETH_SHARED_NAME, + .id = 2, + .dev = { + .platform_data = &mv78xx0_ge10_shared_data, + }, + .num_resources = 1, + .resource = mv78xx0_ge10_shared_resources, +}; + +static struct resource mv78xx0_ge10_resources[] = { + { + .name = "ge10 irq", + .start = IRQ_MV78XX0_GE10_SUM, + .end = IRQ_MV78XX0_GE10_SUM, + .flags = IORESOURCE_IRQ, + }, +}; + +static struct platform_device mv78xx0_ge10 = { + .name = MV643XX_ETH_NAME, + .id = 2, + .num_resources = 1, + .resource = mv78xx0_ge10_resources, +}; + +void __init mv78xx0_ge10_init(struct mv643xx_eth_platform_data *eth_data) +{ + eth_data->shared = &mv78xx0_ge10_shared; + eth_data->shared_smi = &mv78xx0_ge00_shared; + mv78xx0_ge10.dev.platform_data = eth_data; + + platform_device_register(&mv78xx0_ge10_shared); + platform_device_register(&mv78xx0_ge10); +} + + +/***************************************************************************** + * GE11 + ****************************************************************************/ +struct mv643xx_eth_shared_platform_data mv78xx0_ge11_shared_data = { + .t_clk = 0, + .dram = &mv78xx0_mbus_dram_info, +}; + +static struct resource mv78xx0_ge11_shared_resources[] = { + { + .name = "ge11 base", + .start = GE11_PHYS_BASE + 0x2000, + .end = GE11_PHYS_BASE + 0x3fff, + .flags = IORESOURCE_MEM, + }, +}; + +static struct platform_device mv78xx0_ge11_shared = { + .name = MV643XX_ETH_SHARED_NAME, + .id = 3, + .dev = { + .platform_data = &mv78xx0_ge11_shared_data, + }, + .num_resources = 1, + .resource = mv78xx0_ge11_shared_resources, +}; + +static struct resource mv78xx0_ge11_resources[] = { + { + .name = "ge11 irq", + .start = IRQ_MV78XX0_GE11_SUM, + .end = IRQ_MV78XX0_GE11_SUM, + .flags = IORESOURCE_IRQ, + }, +}; + +static struct platform_device mv78xx0_ge11 = { + .name = MV643XX_ETH_NAME, + .id = 3, + .num_resources = 1, + .resource = mv78xx0_ge11_resources, +}; + +void __init mv78xx0_ge11_init(struct mv643xx_eth_platform_data *eth_data) +{ + eth_data->shared = &mv78xx0_ge11_shared; + eth_data->shared_smi = &mv78xx0_ge00_shared; + mv78xx0_ge11.dev.platform_data = eth_data; + + platform_device_register(&mv78xx0_ge11_shared); + platform_device_register(&mv78xx0_ge11); +} + + +/***************************************************************************** + * SATA + ****************************************************************************/ +static struct resource mv78xx0_sata_resources[] = { + { + .name = "sata base", + .start = SATA_PHYS_BASE, + .end = SATA_PHYS_BASE + 0x5000 - 1, + .flags = IORESOURCE_MEM, + }, { + .name = "sata irq", + .start = IRQ_MV78XX0_SATA, + .end = IRQ_MV78XX0_SATA, + .flags = IORESOURCE_IRQ, + }, +}; + +static struct platform_device mv78xx0_sata = { + .name = "sata_mv", + .id = 0, + .dev = { + .coherent_dma_mask = 0xffffffff, + }, + .num_resources = ARRAY_SIZE(mv78xx0_sata_resources), + .resource = mv78xx0_sata_resources, +}; + +void __init mv78xx0_sata_init(struct mv_sata_platform_data *sata_data) +{ + sata_data->dram = &mv78xx0_mbus_dram_info; + mv78xx0_sata.dev.platform_data = sata_data; + platform_device_register(&mv78xx0_sata); +} + + +/***************************************************************************** + * UART0 + ****************************************************************************/ +static struct plat_serial8250_port mv78xx0_uart0_data[] = { + { + .mapbase = UART0_PHYS_BASE, + .membase = (char *)UART0_VIRT_BASE, + .irq = IRQ_MV78XX0_UART_0, + .flags = UPF_SKIP_TEST | UPF_BOOT_AUTOCONF, + .iotype = UPIO_MEM, + .regshift = 2, + .uartclk = 0, + }, { + }, +}; + +static struct resource mv78xx0_uart0_resources[] = { + { + .start = UART0_PHYS_BASE, + .end = UART0_PHYS_BASE + 0xff, + .flags = IORESOURCE_MEM, + }, { + .start = IRQ_MV78XX0_UART_0, + .end = IRQ_MV78XX0_UART_0, + .flags = IORESOURCE_IRQ, + }, +}; + +static struct platform_device mv78xx0_uart0 = { + .name = "serial8250", + .id = 0, + .dev = { + .platform_data = mv78xx0_uart0_data, + }, + .resource = mv78xx0_uart0_resources, + .num_resources = ARRAY_SIZE(mv78xx0_uart0_resources), +}; + +void __init mv78xx0_uart0_init(void) +{ + platform_device_register(&mv78xx0_uart0); +} + + +/***************************************************************************** + * UART1 + ****************************************************************************/ +static struct plat_serial8250_port mv78xx0_uart1_data[] = { + { + .mapbase = UART1_PHYS_BASE, + .membase = (char *)UART1_VIRT_BASE, + .irq = IRQ_MV78XX0_UART_1, + .flags = UPF_SKIP_TEST | UPF_BOOT_AUTOCONF, + .iotype = UPIO_MEM, + .regshift = 2, + .uartclk = 0, + }, { + }, +}; + +static struct resource mv78xx0_uart1_resources[] = { + { + .start = UART1_PHYS_BASE, + .end = UART1_PHYS_BASE + 0xff, + .flags = IORESOURCE_MEM, + }, { + .start = IRQ_MV78XX0_UART_1, + .end = IRQ_MV78XX0_UART_1, + .flags = IORESOURCE_IRQ, + }, +}; + +static struct platform_device mv78xx0_uart1 = { + .name = "serial8250", + .id = 1, + .dev = { + .platform_data = mv78xx0_uart1_data, + }, + .resource = mv78xx0_uart1_resources, + .num_resources = ARRAY_SIZE(mv78xx0_uart1_resources), +}; + +void __init mv78xx0_uart1_init(void) +{ + platform_device_register(&mv78xx0_uart1); +} + + +/***************************************************************************** + * UART2 + ****************************************************************************/ +static struct plat_serial8250_port mv78xx0_uart2_data[] = { + { + .mapbase = UART2_PHYS_BASE, + .membase = (char *)UART2_VIRT_BASE, + .irq = IRQ_MV78XX0_UART_2, + .flags = UPF_SKIP_TEST | UPF_BOOT_AUTOCONF, + .iotype = UPIO_MEM, + .regshift = 2, + .uartclk = 0, + }, { + }, +}; + +static struct resource mv78xx0_uart2_resources[] = { + { + .start = UART2_PHYS_BASE, + .end = UART2_PHYS_BASE + 0xff, + .flags = IORESOURCE_MEM, + }, { + .start = IRQ_MV78XX0_UART_2, + .end = IRQ_MV78XX0_UART_2, + .flags = IORESOURCE_IRQ, + }, +}; + +static struct platform_device mv78xx0_uart2 = { + .name = "serial8250", + .id = 2, + .dev = { + .platform_data = mv78xx0_uart2_data, + }, + .resource = mv78xx0_uart2_resources, + .num_resources = ARRAY_SIZE(mv78xx0_uart2_resources), +}; + +void __init mv78xx0_uart2_init(void) +{ + platform_device_register(&mv78xx0_uart2); +} + + +/***************************************************************************** + * UART3 + ****************************************************************************/ +static struct plat_serial8250_port mv78xx0_uart3_data[] = { + { + .mapbase = UART3_PHYS_BASE, + .membase = (char *)UART3_VIRT_BASE, + .irq = IRQ_MV78XX0_UART_3, + .flags = UPF_SKIP_TEST | UPF_BOOT_AUTOCONF, + .iotype = UPIO_MEM, + .regshift = 2, + .uartclk = 0, + }, { + }, +}; + +static struct resource mv78xx0_uart3_resources[] = { + { + .start = UART3_PHYS_BASE, + .end = UART3_PHYS_BASE + 0xff, + .flags = IORESOURCE_MEM, + }, { + .start = IRQ_MV78XX0_UART_3, + .end = IRQ_MV78XX0_UART_3, + .flags = IORESOURCE_IRQ, + }, +}; + +static struct platform_device mv78xx0_uart3 = { + .name = "serial8250", + .id = 3, + .dev = { + .platform_data = mv78xx0_uart3_data, + }, + .resource = mv78xx0_uart3_resources, + .num_resources = ARRAY_SIZE(mv78xx0_uart3_resources), +}; + +void __init mv78xx0_uart3_init(void) +{ + platform_device_register(&mv78xx0_uart3); +} + + +/***************************************************************************** + * Time handling + ****************************************************************************/ +static void mv78xx0_timer_init(void) +{ + orion_time_init(IRQ_MV78XX0_TIMER_1, get_tclk()); +} + +struct sys_timer mv78xx0_timer = { + .init = mv78xx0_timer_init, +}; + + +/***************************************************************************** + * General + ****************************************************************************/ +static int __init is_l2_writethrough(void) +{ + return !!(readl(CPU_CONTROL) & L2_WRITETHROUGH); +} + +void __init mv78xx0_init(void) +{ + int core_index; + int hclk; + int pclk; + int l2clk; + int tclk; + + core_index = mv78xx0_core_index(); + hclk = get_hclk(); + get_pclk_l2clk(hclk, core_index, &pclk, &l2clk); + tclk = get_tclk(); + + printk(KERN_INFO "MV78xx0 core #%d, ", core_index); + printk("PCLK = %dMHz, ", (pclk + 499999) / 1000000); + printk("L2 = %dMHz, ", (l2clk + 499999) / 1000000); + printk("HCLK = %dMHz, ", (hclk + 499999) / 1000000); + printk("TCLK = %dMHz\n", (tclk + 499999) / 1000000); + + mv78xx0_setup_cpu_mbus(); + +#ifdef CONFIG_CACHE_FEROCEON_L2 + feroceon_l2_init(is_l2_writethrough()); +#endif + + mv78xx0_ge00_shared_data.t_clk = tclk; + mv78xx0_ge01_shared_data.t_clk = tclk; + mv78xx0_ge10_shared_data.t_clk = tclk; + mv78xx0_ge11_shared_data.t_clk = tclk; + mv78xx0_uart0_data[0].uartclk = tclk; + mv78xx0_uart1_data[0].uartclk = tclk; + mv78xx0_uart2_data[0].uartclk = tclk; + mv78xx0_uart3_data[0].uartclk = tclk; +} diff --git a/arch/arm/mach-mv78xx0/common.h b/arch/arm/mach-mv78xx0/common.h new file mode 100644 index 00000000000..78af5de319d --- /dev/null +++ b/arch/arm/mach-mv78xx0/common.h @@ -0,0 +1,49 @@ +/* + * arch/arm/mach-mv78xx0/common.h + * + * Core functions for Marvell MV78xx0 SoCs + * + * This file is licensed under the terms of the GNU General Public + * License version 2. This program is licensed "as is" without any + * warranty of any kind, whether express or implied. + */ + +#ifndef __ARCH_MV78XX0_COMMON_H +#define __ARCH_MV78XX0_COMMON_H + +struct mv643xx_eth_platform_data; +struct mv_sata_platform_data; + +/* + * Basic MV78xx0 init functions used early by machine-setup. + */ +int mv78xx0_core_index(void); +void mv78xx0_map_io(void); +void mv78xx0_init(void); +void mv78xx0_init_irq(void); + +extern struct mbus_dram_target_info mv78xx0_mbus_dram_info; +void mv78xx0_setup_cpu_mbus(void); +void mv78xx0_setup_pcie_io_win(int window, u32 base, u32 size, + int maj, int min); +void mv78xx0_setup_pcie_mem_win(int window, u32 base, u32 size, + int maj, int min); + +void mv78xx0_ehci0_init(void); +void mv78xx0_ehci1_init(void); +void mv78xx0_ehci2_init(void); +void mv78xx0_ge00_init(struct mv643xx_eth_platform_data *eth_data); +void mv78xx0_ge01_init(struct mv643xx_eth_platform_data *eth_data); +void mv78xx0_ge10_init(struct mv643xx_eth_platform_data *eth_data); +void mv78xx0_ge11_init(struct mv643xx_eth_platform_data *eth_data); +void mv78xx0_pcie_init(int init_port0, int init_port1); +void mv78xx0_sata_init(struct mv_sata_platform_data *sata_data); +void mv78xx0_uart0_init(void); +void mv78xx0_uart1_init(void); +void mv78xx0_uart2_init(void); +void mv78xx0_uart3_init(void); + +extern struct sys_timer mv78xx0_timer; + + +#endif diff --git a/arch/arm/mach-mv78xx0/db78x00-bp-setup.c b/arch/arm/mach-mv78xx0/db78x00-bp-setup.c new file mode 100644 index 00000000000..0c93d19193d --- /dev/null +++ b/arch/arm/mach-mv78xx0/db78x00-bp-setup.c @@ -0,0 +1,94 @@ +/* + * arch/arm/mach-mv78xx0/db78x00-bp-setup.c + * + * Marvell DB-78x00-BP Development Board Setup + * + * This file is licensed under the terms of the GNU General Public + * License version 2. This program is licensed "as is" without any + * warranty of any kind, whether express or implied. + */ + +#include <linux/kernel.h> +#include <linux/init.h> +#include <linux/platform_device.h> +#include <linux/ata_platform.h> +#include <linux/mv643xx_eth.h> +#include <asm/arch/mv78xx0.h> +#include <asm/mach-types.h> +#include <asm/mach/arch.h> +#include "common.h" + +static struct mv643xx_eth_platform_data db78x00_ge00_data = { + .phy_addr = 8, +}; + +static struct mv643xx_eth_platform_data db78x00_ge01_data = { + .phy_addr = 9, +}; + +static struct mv643xx_eth_platform_data db78x00_ge10_data = { + .phy_addr = -1, +}; + +static struct mv643xx_eth_platform_data db78x00_ge11_data = { + .phy_addr = -1, +}; + +static struct mv_sata_platform_data db78x00_sata_data = { + .n_ports = 2, +}; + +static void __init db78x00_init(void) +{ + /* + * Basic MV78xx0 setup. Needs to be called early. + */ + mv78xx0_init(); + + /* + * Partition on-chip peripherals between the two CPU cores. + */ + if (mv78xx0_core_index() == 0) { + mv78xx0_ehci0_init(); + mv78xx0_ehci1_init(); + mv78xx0_ehci2_init(); + mv78xx0_ge00_init(&db78x00_ge00_data); + mv78xx0_ge01_init(&db78x00_ge01_data); + mv78xx0_ge10_init(&db78x00_ge10_data); + mv78xx0_ge11_init(&db78x00_ge11_data); + mv78xx0_sata_init(&db78x00_sata_data); + mv78xx0_uart0_init(); + mv78xx0_uart2_init(); + } else { + mv78xx0_uart1_init(); + mv78xx0_uart3_init(); + } +} + +static int __init db78x00_pci_init(void) +{ + if (machine_is_db78x00_bp()) { + /* + * Assign the x16 PCIe slot on the board to CPU core + * #0, and let CPU core #1 have the four x1 slots. + */ + if (mv78xx0_core_index() == 0) + mv78xx0_pcie_init(0, 1); + else + mv78xx0_pcie_init(1, 0); + } + + return 0; +} +subsys_initcall(db78x00_pci_init); + +MACHINE_START(DB78X00_BP, "Marvell DB-78x00-BP Development Board") + /* Maintainer: Lennert Buytenhek <buytenh@marvell.com> */ + .phys_io = MV78XX0_REGS_PHYS_BASE, + .io_pg_offst = ((MV78XX0_REGS_VIRT_BASE) >> 18) & 0xfffc, + .boot_params = 0x00000100, + .init_machine = db78x00_init, + .map_io = mv78xx0_map_io, + .init_irq = mv78xx0_init_irq, + .timer = &mv78xx0_timer, +MACHINE_END diff --git a/arch/arm/mach-mv78xx0/irq.c b/arch/arm/mach-mv78xx0/irq.c new file mode 100644 index 00000000000..60f4ee4d453 --- /dev/null +++ b/arch/arm/mach-mv78xx0/irq.c @@ -0,0 +1,22 @@ +/* + * arch/arm/mach-mv78xx0/irq.c + * + * MV78xx0 IRQ handling. + * + * This file is licensed under the terms of the GNU General Public + * License version 2. This program is licensed "as is" without any + * warranty of any kind, whether express or implied. + */ + +#include <linux/kernel.h> +#include <linux/init.h> +#include <linux/pci.h> +#include <asm/arch/mv78xx0.h> +#include <asm/plat-orion/irq.h> +#include "common.h" + +void __init mv78xx0_init_irq(void) +{ + orion_irq_init(0, (void __iomem *)(IRQ_VIRT_BASE + IRQ_MASK_LOW_OFF)); + orion_irq_init(32, (void __iomem *)(IRQ_VIRT_BASE + IRQ_MASK_HIGH_OFF)); +} diff --git a/arch/arm/mach-mv78xx0/pcie.c b/arch/arm/mach-mv78xx0/pcie.c new file mode 100644 index 00000000000..b78e1443159 --- /dev/null +++ b/arch/arm/mach-mv78xx0/pcie.c @@ -0,0 +1,312 @@ +/* + * arch/arm/mach-mv78xx0/pcie.c + * + * PCIe functions for Marvell MV78xx0 SoCs + * + * This file is licensed under the terms of the GNU General Public + * License version 2. This program is licensed "as is" without any + * warranty of any kind, whether express or implied. + */ + +#include <linux/kernel.h> +#include <linux/pci.h> +#include <linux/mbus.h> +#include <asm/mach/pci.h> +#include <asm/plat-orion/pcie.h> +#include "common.h" + +struct pcie_port { + u8 maj; + u8 min; + u8 root_bus_nr; + void __iomem *base; + spinlock_t conf_lock; + char io_space_name[16]; + char mem_space_name[16]; + struct resource res[2]; +}; + +static struct pcie_port pcie_port[8]; +static int num_pcie_ports; +static struct resource pcie_io_space; +static struct resource pcie_mem_space; + + +static void __init mv78xx0_pcie_preinit(void) +{ + int i; + u32 size_each; + u32 start; + int win; + + pcie_io_space.name = "PCIe I/O Space"; + pcie_io_space.start = MV78XX0_PCIE_IO_PHYS_BASE(0); + pcie_io_space.end = + MV78XX0_PCIE_IO_PHYS_BASE(0) + MV78XX0_PCIE_IO_SIZE * 8 - 1; + pcie_io_space.flags = IORESOURCE_IO; + if (request_resource(&iomem_resource, &pcie_io_space)) + panic("can't allocate PCIe I/O space"); + + pcie_mem_space.name = "PCIe MEM Space"; + pcie_mem_space.start = MV78XX0_PCIE_MEM_PHYS_BASE; + pcie_mem_space.end = + MV78XX0_PCIE_MEM_PHYS_BASE + MV78XX0_PCIE_MEM_SIZE - 1; + pcie_mem_space.flags = IORESOURCE_MEM; + if (request_resource(&iomem_resource, &pcie_mem_space)) + panic("can't allocate PCIe MEM space"); + + for (i = 0; i < num_pcie_ports; i++) { + struct pcie_port *pp = pcie_port + i; + + snprintf(pp->io_space_name, sizeof(pp->io_space_name), + "PCIe %d.%d I/O", pp->maj, pp->min); + pp->io_space_name[sizeof(pp->io_space_name) - 1] = 0; + pp->res[0].name = pp->io_space_name; + pp->res[0].start = MV78XX0_PCIE_IO_PHYS_BASE(i); + pp->res[0].end = pp->res[0].start + MV78XX0_PCIE_IO_SIZE - 1; + pp->res[0].flags = IORESOURCE_IO; + + snprintf(pp->mem_space_name, sizeof(pp->mem_space_name), + "PCIe %d.%d MEM", pp->maj, pp->min); + pp->mem_space_name[sizeof(pp->mem_space_name) - 1] = 0; + pp->res[1].name = pp->mem_space_name; + pp->res[1].flags = IORESOURCE_MEM; + } + + switch (num_pcie_ports) { + case 0: + size_each = 0; + break; + + case 1: + size_each = 0x30000000; + break; + + case 2 ... 3: + size_each = 0x10000000; + break; + + case 4 ... 6: + size_each = 0x08000000; + break; + + case 7: + size_each = 0x04000000; + break; + + default: + panic("invalid number of PCIe ports"); + } + + start = MV78XX0_PCIE_MEM_PHYS_BASE; + for (i = 0; i < num_pcie_ports; i++) { + struct pcie_port *pp = pcie_port + i; + + pp->res[1].start = start; + pp->res[1].end = start + size_each - 1; + start += size_each; + } + + for (i = 0; i < num_pcie_ports; i++) { + struct pcie_port *pp = pcie_port + i; + + if (request_resource(&pcie_io_space, &pp->res[0])) + panic("can't allocate PCIe I/O sub-space"); + + if (request_resource(&pcie_mem_space, &pp->res[1])) + panic("can't allocate PCIe MEM sub-space"); + } + + win = 0; + for (i = 0; i < num_pcie_ports; i++) { + struct pcie_port *pp = pcie_port + i; + + mv78xx0_setup_pcie_io_win(win++, pp->res[0].start, + pp->res[0].end - pp->res[0].start + 1, + pp->maj, pp->min); + + mv78xx0_setup_pcie_mem_win(win++, pp->res[1].start, + pp->res[1].end - pp->res[1].start + 1, + pp->maj, pp->min); + } +} + +static int __init mv78xx0_pcie_setup(int nr, struct pci_sys_data *sys) +{ + struct pcie_port *pp; + + if (nr >= num_pcie_ports) + return 0; + + pp = &pcie_port[nr]; + pp->root_bus_nr = sys->busnr; + + /* + * Generic PCIe unit setup. + */ + orion_pcie_set_local_bus_nr(pp->base, sys->busnr); + orion_pcie_setup(pp->base, &mv78xx0_mbus_dram_info); + + sys->resource[0] = &pp->res[0]; + sys->resource[1] = &pp->res[1]; + sys->resource[2] = NULL; + + return 1; +} + +static struct pcie_port *bus_to_port(int bus) +{ + int i; + + for (i = num_pcie_ports - 1; i >= 0; i--) { + int rbus = pcie_port[i].root_bus_nr; + if (rbus != -1 && rbus <= bus) + break; + } + + return i >= 0 ? pcie_port + i : NULL; +} + +static int pcie_valid_config(struct pcie_port *pp, int bus, int dev) +{ + /* + * Don't go out when trying to access nonexisting devices + * on the local bus. + */ + if (bus == pp->root_bus_nr && dev > 1) + return 0; + + return 1; +} + +static int pcie_rd_conf(struct pci_bus *bus, u32 devfn, int where, + int size, u32 *val) +{ + struct pcie_port *pp = bus_to_port(bus->number); + unsigned long flags; + int ret; + + if (pcie_valid_config(pp, bus->number, PCI_SLOT(devfn)) == 0) { + *val = 0xffffffff; + return PCIBIOS_DEVICE_NOT_FOUND; + } + + spin_lock_irqsave(&pp->conf_lock, flags); + ret = orion_pcie_rd_conf(pp->base, bus, devfn, where, size, val); + spin_unlock_irqrestore(&pp->conf_lock, flags); + + return ret; +} + +static int pcie_wr_conf(struct pci_bus *bus, u32 devfn, + int where, int size, u32 val) +{ + struct pcie_port *pp = bus_to_port(bus->number); + unsigned long flags; + int ret; + + if (pcie_valid_config(pp, bus->number, PCI_SLOT(devfn)) == 0) + return PCIBIOS_DEVICE_NOT_FOUND; + + spin_lock_irqsave(&pp->conf_lock, flags); + ret = orion_pcie_wr_conf(pp->base, bus, devfn, where, size, val); + spin_unlock_irqrestore(&pp->conf_lock, flags); + + return ret; +} + +static struct pci_ops pcie_ops = { + .read = pcie_rd_conf, + .write = pcie_wr_conf, +}; + +static void __devinit rc_pci_fixup(struct pci_dev *dev) +{ + /* + * Prevent enumeration of root complex. + */ + if (dev->bus->parent == NULL && dev->devfn == 0) { + int i; + + for (i = 0; i < DEVICE_COUNT_RESOURCE; i++) { + dev->resource[i].start = 0; + dev->resource[i].end = 0; + dev->resource[i].flags = 0; + } + } +} +DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_MARVELL, PCI_ANY_ID, rc_pci_fixup); + +static struct pci_bus __init * +mv78xx0_pcie_scan_bus(int nr, struct pci_sys_data *sys) +{ + struct pci_bus *bus; + + if (nr < num_pcie_ports) { + bus = pci_scan_bus(sys->busnr, &pcie_ops, sys); + } else { + bus = NULL; + BUG(); + } + + return bus; +} + +static int __init mv78xx0_pcie_map_irq(struct pci_dev *dev, u8 slot, u8 pin) +{ + struct pcie_port *pp = bus_to_port(dev->bus->number); + + return IRQ_MV78XX0_PCIE_00 + (pp->maj << 2) + pp->min; +} + +static struct hw_pci mv78xx0_pci __initdata = { + .nr_controllers = 8, + .preinit = mv78xx0_pcie_preinit, + .swizzle = pci_std_swizzle, + .setup = mv78xx0_pcie_setup, + .scan = mv78xx0_pcie_scan_bus, + .map_irq = mv78xx0_pcie_map_irq, +}; + +static void __init add_pcie_port(int maj, int min, unsigned long base) +{ + printk(KERN_INFO "MV78xx0 PCIe port %d.%d: ", maj, min); + + if (orion_pcie_link_up((void __iomem *)base)) { + struct pcie_port *pp = &pcie_port[num_pcie_ports++]; + + printk("link up\n"); + + pp->maj = maj; + pp->min = min; + pp->root_bus_nr = -1; + pp->base = (void __iomem *)base; + spin_lock_init(&pp->conf_lock); + memset(pp->res, 0, sizeof(pp->res)); + } else { + printk("link down, ignoring\n"); + } +} + +void __init mv78xx0_pcie_init(int init_port0, int init_port1) +{ + if (init_port0) { + add_pcie_port(0, 0, PCIE00_VIRT_BASE); + if (!orion_pcie_x4_mode((void __iomem *)PCIE00_VIRT_BASE)) { + add_pcie_port(0, 1, PCIE01_VIRT_BASE); + add_pcie_port(0, 2, PCIE02_VIRT_BASE); + add_pcie_port(0, 3, PCIE03_VIRT_BASE); + } + } + + if (init_port1) { + add_pcie_port(1, 0, PCIE10_VIRT_BASE); + if (!orion_pcie_x4_mode((void __iomem *)PCIE10_VIRT_BASE)) { + add_pcie_port(1, 1, PCIE11_VIRT_BASE); + add_pcie_port(1, 2, PCIE12_VIRT_BASE); + add_pcie_port(1, 3, PCIE13_VIRT_BASE); + } + } + + pci_common_init(&mv78xx0_pci); +} diff --git a/arch/arm/mach-omap1/Makefile b/arch/arm/mach-omap1/Makefile index c06f5254c0f..1bda8f5d754 100644 --- a/arch/arm/mach-omap1/Makefile +++ b/arch/arm/mach-omap1/Makefile @@ -3,7 +3,9 @@ # # Common support -obj-y := io.o id.o clock.o irq.o mux.o serial.o devices.o +obj-y := io.o id.o sram.o clock.o irq.o mux.o serial.o devices.o + +obj-$(CONFIG_OMAP_MCBSP) += mcbsp.o obj-$(CONFIG_OMAP_MPU_TIMER) += time.o obj-$(CONFIG_OMAP_32K_TIMER) += timer32k.o diff --git a/arch/arm/mach-omap1/board-nokia770.c b/arch/arm/mach-omap1/board-nokia770.c index bcb984f2300..3f39e0e79c9 100644 --- a/arch/arm/mach-omap1/board-nokia770.c +++ b/arch/arm/mach-omap1/board-nokia770.c @@ -10,6 +10,7 @@ #include <linux/kernel.h> #include <linux/init.h> +#include <linux/mutex.h> #include <linux/platform_device.h> #include <linux/input.h> #include <linux/clk.h> @@ -202,7 +203,7 @@ static struct omap_board_config_kernel nokia770_config[] __initdata = { #define AMPLIFIER_CTRL_GPIO 58 static struct clk *dspxor_ck; -static DECLARE_MUTEX(audio_pwr_sem); +static DEFINE_MUTEX(audio_pwr_lock); /* * audio_pwr_state * +--+-------------------------+---------------------------------------+ @@ -218,7 +219,7 @@ static DECLARE_MUTEX(audio_pwr_sem); static int audio_pwr_state = -1; /* - * audio_pwr_up / down should be called under audio_pwr_sem + * audio_pwr_up / down should be called under audio_pwr_lock */ static void nokia770_audio_pwr_up(void) { @@ -237,11 +238,11 @@ static void nokia770_audio_pwr_up(void) static void codec_delayed_power_down(struct work_struct *work) { - down(&audio_pwr_sem); + mutex_lock(&audio_pwr_lock); if (audio_pwr_state == -1) aic23_power_down(); clk_disable(dspxor_ck); - up(&audio_pwr_sem); + mutex_unlock(&audio_pwr_lock); } static DECLARE_DELAYED_WORK(codec_power_down_work, codec_delayed_power_down); @@ -258,19 +259,19 @@ static void nokia770_audio_pwr_down(void) static int nokia770_audio_pwr_up_request(struct dsp_kfunc_device *kdev, int stage) { - down(&audio_pwr_sem); + mutex_lock(&audio_pwr_lock); if (audio_pwr_state == -1) nokia770_audio_pwr_up(); /* force audio_pwr_state = 0, even if it was 1. */ audio_pwr_state = 0; - up(&audio_pwr_sem); + mutex_unlock(&audio_pwr_lock); return 0; } static int nokia770_audio_pwr_down_request(struct dsp_kfunc_device *kdev, int stage) { - down(&audio_pwr_sem); + mutex_lock(&audio_pwr_lock); switch (stage) { case 1: if (audio_pwr_state == 0) @@ -283,7 +284,7 @@ nokia770_audio_pwr_down_request(struct dsp_kfunc_device *kdev, int stage) } break; } - up(&audio_pwr_sem); + mutex_unlock(&audio_pwr_lock); return 0; } diff --git a/arch/arm/mach-omap1/board-osk.c b/arch/arm/mach-omap1/board-osk.c index a66505f58b1..845c66371ca 100644 --- a/arch/arm/mach-omap1/board-osk.c +++ b/arch/arm/mach-omap1/board-osk.c @@ -267,13 +267,17 @@ static struct i2c_board_info __initdata osk_i2c_board_info[] = { static void __init osk_init_smc91x(void) { + u32 l; + if ((gpio_request(0, "smc_irq")) < 0) { printk("Error requesting gpio 0 for smc91x irq\n"); return; } /* Check EMIFS wait states to fix errors with SMC_GET_PKT_HDR */ - EMIFS_CCS(1) |= 0x3; + l = omap_readl(EMIFS_CCS(1)); + l |= 0x3; + omap_writel(l, EMIFS_CCS(1)); } static void __init osk_init_cf(void) @@ -526,20 +530,26 @@ static void __init osk_mistral_init(void) { } static void __init osk_init(void) { + u32 l; + /* Workaround for wrong CS3 (NOR flash) timing * There are some U-Boot versions out there which configure * wrong CS3 memory timings. This mainly leads to CRC * or similar errors if you use NOR flash (e.g. with JFFS2) */ - if (EMIFS_CCS(3) != EMIFS_CS3_VAL) - EMIFS_CCS(3) = EMIFS_CS3_VAL; + l = omap_readl(EMIFS_CCS(3)); + if (l != EMIFS_CS3_VAL) + omap_writel(EMIFS_CS3_VAL, EMIFS_CCS(3)); osk_flash_resource.end = osk_flash_resource.start = omap_cs3_phys(); osk_flash_resource.end += SZ_32M - 1; platform_add_devices(osk5912_devices, ARRAY_SIZE(osk5912_devices)); omap_board_config = osk_config; omap_board_config_size = ARRAY_SIZE(osk_config); - USB_TRANSCEIVER_CTRL_REG |= (3 << 1); + + l = omap_readl(USB_TRANSCEIVER_CTRL); + l |= (3 << 1); + omap_writel(l, USB_TRANSCEIVER_CTRL); /* irq for tps65010 chip */ /* bootloader effectively does: omap_cfg_reg(U19_1610_MPUIO1); */ diff --git a/arch/arm/mach-omap1/fpga.c b/arch/arm/mach-omap1/fpga.c index 30e18810904..0cf62ef5ecb 100644 --- a/arch/arm/mach-omap1/fpga.c +++ b/arch/arm/mach-omap1/fpga.c @@ -32,7 +32,7 @@ static void fpga_mask_irq(unsigned int irq) { - irq -= OMAP1510_IH_FPGA_BASE; + irq -= OMAP_FPGA_IRQ_BASE; if (irq < 8) __raw_writeb((__raw_readb(OMAP1510_FPGA_IMR_LO) @@ -65,7 +65,7 @@ static void fpga_ack_irq(unsigned int irq) static void fpga_unmask_irq(unsigned int irq) { - irq -= OMAP1510_IH_FPGA_BASE; + irq -= OMAP_FPGA_IRQ_BASE; if (irq < 8) __raw_writeb((__raw_readb(OMAP1510_FPGA_IMR_LO) | (1 << irq)), @@ -95,8 +95,8 @@ void innovator_fpga_IRQ_demux(unsigned int irq, struct irq_desc *desc) if (!stat) return; - for (fpga_irq = OMAP1510_IH_FPGA_BASE; - (fpga_irq < (OMAP1510_IH_FPGA_BASE + NR_FPGA_IRQS)) && stat; + for (fpga_irq = OMAP_FPGA_IRQ_BASE; + (fpga_irq < OMAP_FPGA_IRQ_END) && stat; fpga_irq++, stat >>= 1) { if (stat & 1) { d = irq_desc + fpga_irq; @@ -151,7 +151,7 @@ void omap1510_fpga_init_irq(void) __raw_writeb(0, OMAP1510_FPGA_IMR_HI); __raw_writeb(0, INNOVATOR_FPGA_IMR2); - for (i = OMAP1510_IH_FPGA_BASE; i < (OMAP1510_IH_FPGA_BASE + NR_FPGA_IRQS); i++) { + for (i = OMAP_FPGA_IRQ_BASE; i < OMAP_FPGA_IRQ_END; i++) { if (i == OMAP1510_INT_FPGA_TS) { /* diff --git a/arch/arm/mach-omap1/mcbsp.c b/arch/arm/mach-omap1/mcbsp.c new file mode 100644 index 00000000000..2d2c2522b04 --- /dev/null +++ b/arch/arm/mach-omap1/mcbsp.c @@ -0,0 +1,280 @@ +/* + * linux/arch/arm/mach-omap1/mcbsp.c + * + * Copyright (C) 2008 Instituto Nokia de Tecnologia + * Contact: Eduardo Valentin <eduardo.valentin@indt.org.br> + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + * + * Multichannel mode not supported. + */ +#include <linux/module.h> +#include <linux/init.h> +#include <linux/clk.h> +#include <linux/err.h> +#include <linux/io.h> +#include <linux/platform_device.h> + +#include <asm/arch/dma.h> +#include <asm/arch/mux.h> +#include <asm/arch/cpu.h> +#include <asm/arch/mcbsp.h> +#include <asm/arch/dsp_common.h> + +#define DPS_RSTCT2_PER_EN (1 << 0) +#define DSP_RSTCT2_WD_PER_EN (1 << 1) + +struct mcbsp_internal_clk { + struct clk clk; + struct clk **childs; + int n_childs; +}; + +#if defined(CONFIG_ARCH_OMAP15XX) || defined(CONFIG_ARCH_OMAP16XX) +static void omap_mcbsp_clk_init(struct mcbsp_internal_clk *mclk) +{ + const char *clk_names[] = { "dsp_ck", "api_ck", "dspxor_ck" }; + int i; + + mclk->n_childs = ARRAY_SIZE(clk_names); + mclk->childs = kzalloc(mclk->n_childs * sizeof(struct clk *), + GFP_KERNEL); + + for (i = 0; i < mclk->n_childs; i++) { + /* We fake a platform device to get correct device id */ + struct platform_device pdev; + + pdev.dev.bus = &platform_bus_type; + pdev.id = mclk->clk.id; + mclk->childs[i] = clk_get(&pdev.dev, clk_names[i]); + if (IS_ERR(mclk->childs[i])) + printk(KERN_ERR "Could not get clock %s (%d).\n", + clk_names[i], mclk->clk.id); + } +} + +static int omap_mcbsp_clk_enable(struct clk *clk) +{ + struct mcbsp_internal_clk *mclk = container_of(clk, + struct mcbsp_internal_clk, clk); + int i; + + for (i = 0; i < mclk->n_childs; i++) + clk_enable(mclk->childs[i]); + return 0; +} + +static void omap_mcbsp_clk_disable(struct clk *clk) +{ + struct mcbsp_internal_clk *mclk = container_of(clk, + struct mcbsp_internal_clk, clk); + int i; + + for (i = 0; i < mclk->n_childs; i++) + clk_disable(mclk->childs[i]); +} + +static struct mcbsp_internal_clk omap_mcbsp_clks[] = { + { + .clk = { + .name = "mcbsp_clk", + .id = 1, + .enable = omap_mcbsp_clk_enable, + .disable = omap_mcbsp_clk_disable, + }, + }, + { + .clk = { + .name = "mcbsp_clk", + .id = 3, + .enable = omap_mcbsp_clk_enable, + .disable = omap_mcbsp_clk_disable, + }, + }, +}; + +#define omap_mcbsp_clks_size ARRAY_SIZE(omap_mcbsp_clks) +#else +#define omap_mcbsp_clks_size 0 +static struct mcbsp_internal_clk __initdata *omap_mcbsp_clks; +static inline void omap_mcbsp_clk_init(struct mcbsp_internal_clk *mclk) +{ } +#endif + +static int omap1_mcbsp_check(unsigned int id) +{ + /* REVISIT: Check correctly for number of registered McBSPs */ + if (cpu_is_omap730()) { + if (id > OMAP_MAX_MCBSP_COUNT - 2) { + printk(KERN_ERR "OMAP-McBSP: McBSP%d doesn't exist\n", + id + 1); + return -ENODEV; + } + return 0; + } + + if (cpu_is_omap15xx() || cpu_is_omap16xx()) { + if (id > OMAP_MAX_MCBSP_COUNT - 1) { + printk(KERN_ERR "OMAP-McBSP: McBSP%d doesn't exist\n", + id + 1); + return -ENODEV; + } + return 0; + } + + return -ENODEV; +} + +static void omap1_mcbsp_request(unsigned int id) +{ + /* + * On 1510, 1610 and 1710, McBSP1 and McBSP3 + * are DSP public peripherals. + */ + if (id == OMAP_MCBSP1 || id == OMAP_MCBSP3) { + omap_dsp_request_mem(); + /* + * DSP external peripheral reset + * FIXME: This should be moved to dsp code + */ + __raw_writew(__raw_readw(DSP_RSTCT2) | DPS_RSTCT2_PER_EN | + DSP_RSTCT2_WD_PER_EN, DSP_RSTCT2); + } +} + +static void omap1_mcbsp_free(unsigned int id) +{ + if (id == OMAP_MCBSP1 || id == OMAP_MCBSP3) + omap_dsp_release_mem(); +} + +static struct omap_mcbsp_ops omap1_mcbsp_ops = { + .check = omap1_mcbsp_check, + .request = omap1_mcbsp_request, + .free = omap1_mcbsp_free, +}; + +#ifdef CONFIG_ARCH_OMAP730 +static struct omap_mcbsp_platform_data omap730_mcbsp_pdata[] = { + { + .virt_base = io_p2v(OMAP730_MCBSP1_BASE), + .dma_rx_sync = OMAP_DMA_MCBSP1_RX, + .dma_tx_sync = OMAP_DMA_MCBSP1_TX, + .rx_irq = INT_730_McBSP1RX, + .tx_irq = INT_730_McBSP1TX, + .ops = &omap1_mcbsp_ops, + }, + { + .virt_base = io_p2v(OMAP730_MCBSP2_BASE), + .dma_rx_sync = OMAP_DMA_MCBSP3_RX, + .dma_tx_sync = OMAP_DMA_MCBSP3_TX, + .rx_irq = INT_730_McBSP2RX, + .tx_irq = INT_730_McBSP2TX, + .ops = &omap1_mcbsp_ops, + }, +}; +#define OMAP730_MCBSP_PDATA_SZ ARRAY_SIZE(omap730_mcbsp_pdata) +#else +#define omap730_mcbsp_pdata NULL +#define OMAP730_MCBSP_PDATA_SZ 0 +#endif + +#ifdef CONFIG_ARCH_OMAP15XX +static struct omap_mcbsp_platform_data omap15xx_mcbsp_pdata[] = { + { + .virt_base = OMAP1510_MCBSP1_BASE, + .dma_rx_sync = OMAP_DMA_MCBSP1_RX, + .dma_tx_sync = OMAP_DMA_MCBSP1_TX, + .rx_irq = INT_McBSP1RX, + .tx_irq = INT_McBSP1TX, + .ops = &omap1_mcbsp_ops, + .clk_name = "mcbsp_clk", + }, + { + .virt_base = io_p2v(OMAP1510_MCBSP2_BASE), + .dma_rx_sync = OMAP_DMA_MCBSP2_RX, + .dma_tx_sync = OMAP_DMA_MCBSP2_TX, + .rx_irq = INT_1510_SPI_RX, + .tx_irq = INT_1510_SPI_TX, + .ops = &omap1_mcbsp_ops, + }, + { + .virt_base = OMAP1510_MCBSP3_BASE, + .dma_rx_sync = OMAP_DMA_MCBSP3_RX, + .dma_tx_sync = OMAP_DMA_MCBSP3_TX, + .rx_irq = INT_McBSP3RX, + .tx_irq = INT_McBSP3TX, + .ops = &omap1_mcbsp_ops, + .clk_name = "mcbsp_clk", + }, +}; +#define OMAP15XX_MCBSP_PDATA_SZ ARRAY_SIZE(omap15xx_mcbsp_pdata) +#else +#define omap15xx_mcbsp_pdata NULL +#define OMAP15XX_MCBSP_PDATA_SZ 0 +#endif + +#ifdef CONFIG_ARCH_OMAP16XX +static struct omap_mcbsp_platform_data omap16xx_mcbsp_pdata[] = { + { + .virt_base = OMAP1610_MCBSP1_BASE, + .dma_rx_sync = OMAP_DMA_MCBSP1_RX, + .dma_tx_sync = OMAP_DMA_MCBSP1_TX, + .rx_irq = INT_McBSP1RX, + .tx_irq = INT_McBSP1TX, + .ops = &omap1_mcbsp_ops, + .clk_name = "mcbsp_clk", + }, + { + .virt_base = io_p2v(OMAP1610_MCBSP2_BASE), + .dma_rx_sync = OMAP_DMA_MCBSP2_RX, + .dma_tx_sync = OMAP_DMA_MCBSP2_TX, + .rx_irq = INT_1610_McBSP2_RX, + .tx_irq = INT_1610_McBSP2_TX, + .ops = &omap1_mcbsp_ops, + }, + { + .virt_base = OMAP1610_MCBSP3_BASE, + .dma_rx_sync = OMAP_DMA_MCBSP3_RX, + .dma_tx_sync = OMAP_DMA_MCBSP3_TX, + .rx_irq = INT_McBSP3RX, + .tx_irq = INT_McBSP3TX, + .ops = &omap1_mcbsp_ops, + .clk_name = "mcbsp_clk", + }, +}; +#define OMAP16XX_MCBSP_PDATA_SZ ARRAY_SIZE(omap16xx_mcbsp_pdata) +#else +#define omap16xx_mcbsp_pdata NULL +#define OMAP16XX_MCBSP_PDATA_SZ 0 +#endif + +int __init omap1_mcbsp_init(void) +{ + int i; + + for (i = 0; i < omap_mcbsp_clks_size; i++) { + if (cpu_is_omap15xx() || cpu_is_omap16xx()) { + omap_mcbsp_clk_init(&omap_mcbsp_clks[i]); + clk_register(&omap_mcbsp_clks[i].clk); + } + } + + if (cpu_is_omap730()) + omap_mcbsp_register_board_cfg(omap730_mcbsp_pdata, + OMAP730_MCBSP_PDATA_SZ); + + if (cpu_is_omap15xx()) + omap_mcbsp_register_board_cfg(omap15xx_mcbsp_pdata, + OMAP15XX_MCBSP_PDATA_SZ); + + if (cpu_is_omap16xx()) + omap_mcbsp_register_board_cfg(omap16xx_mcbsp_pdata, + OMAP16XX_MCBSP_PDATA_SZ); + + return omap_mcbsp_init(); +} + +arch_initcall(omap1_mcbsp_init); diff --git a/arch/arm/mach-omap1/pm.c b/arch/arm/mach-omap1/pm.c index e6c64e10b7e..742f79e73bd 100644 --- a/arch/arm/mach-omap1/pm.c +++ b/arch/arm/mach-omap1/pm.c @@ -116,13 +116,6 @@ void omap_pm_idle(void) return; } - /* - * Since an interrupt may set up a timer, we don't want to - * reprogram the hardware timer with interrupts enabled. - * Re-enable interrupts only after returning from idle. - */ - timer_dyn_reprogram(); - #ifdef CONFIG_OMAP_MPU_TIMER #warning Enable 32kHz OS timer in order to allow sleep states in idle use_idlect1 = use_idlect1 & ~(1 << 9); diff --git a/arch/arm/plat-omap/sram-fn.S b/arch/arm/mach-omap1/sram.S index 9e1813c77e0..126d252062d 100644 --- a/arch/arm/plat-omap/sram-fn.S +++ b/arch/arm/mach-omap1/sram.S @@ -18,7 +18,7 @@ /* * Reprograms ULPD and CKCTL. */ -ENTRY(sram_reprogram_clock) +ENTRY(omap1_sram_reprogram_clock) stmfd sp!, {r0 - r12, lr} @ save registers on stack mov r2, #IO_ADDRESS(DPLL_CTL) & 0xff000000 @@ -53,5 +53,5 @@ lock: ldrh r4, [r2], #0 @ read back dpll value out: ldmfd sp!, {r0 - r12, pc} @ restore regs and return -ENTRY(sram_reprogram_clock_sz) - .word . - sram_reprogram_clock +ENTRY(omap1_sram_reprogram_clock_sz) + .word . - omap1_sram_reprogram_clock diff --git a/arch/arm/mach-omap2/Makefile b/arch/arm/mach-omap2/Makefile index 2feb6870b73..93ee990618e 100644 --- a/arch/arm/mach-omap2/Makefile +++ b/arch/arm/mach-omap2/Makefile @@ -3,9 +3,15 @@ # # Common support -obj-y := irq.o id.o io.o sram-fn.o memory.o control.o prcm.o clock.o mux.o \ +obj-y := irq.o id.o io.o memory.o control.o prcm.o clock.o mux.o \ devices.o serial.o gpmc.o timer-gp.o +obj-$(CONFIG_OMAP_MCBSP) += mcbsp.o + +# Functions loaded to SRAM +obj-$(CONFIG_ARCH_OMAP2420) += sram242x.o +obj-$(CONFIG_ARCH_OMAP2430) += sram243x.o + # Power Management obj-$(CONFIG_PM) += pm.o sleep.o diff --git a/arch/arm/mach-omap2/clock.c b/arch/arm/mach-omap2/clock.c index ab9fc57d25f..15675bce801 100644 --- a/arch/arm/mach-omap2/clock.c +++ b/arch/arm/mach-omap2/clock.c @@ -41,6 +41,24 @@ #define MAX_CLOCK_ENABLE_WAIT 100000 +/* DPLL rate rounding: minimum DPLL multiplier, divider values */ +#define DPLL_MIN_MULTIPLIER 1 +#define DPLL_MIN_DIVIDER 1 + +/* Possible error results from _dpll_test_mult */ +#define DPLL_MULT_UNDERFLOW (1 << 0) + +/* + * Scale factor to mitigate roundoff errors in DPLL rate rounding. + * The higher the scale factor, the greater the risk of arithmetic overflow, + * but the closer the rounded rate to the target rate. DPLL_SCALE_FACTOR + * must be a power of DPLL_SCALE_BASE. + */ +#define DPLL_SCALE_FACTOR 64 +#define DPLL_SCALE_BASE 2 +#define DPLL_ROUNDING_VAL ((DPLL_SCALE_BASE / 2) * \ + (DPLL_SCALE_FACTOR / DPLL_SCALE_BASE)) + u8 cpu_mask; /*------------------------------------------------------------------------- @@ -95,7 +113,7 @@ u32 omap2_get_dpll_rate(struct clk *clk) { long long dpll_clk; u32 dpll_mult, dpll_div, dpll; - const struct dpll_data *dd; + struct dpll_data *dd; dd = clk->dpll_data; /* REVISIT: What do we return on error? */ @@ -603,7 +621,8 @@ int omap2_clksel_set_rate(struct clk *clk, unsigned long rate) clk->rate = clk->parent->rate / new_div; if (clk->flags & DELAYED_APP && cpu_is_omap24xx()) { - __raw_writel(OMAP24XX_VALID_CONFIG, OMAP24XX_PRCM_CLKCFG_CTRL); + prm_write_mod_reg(OMAP24XX_VALID_CONFIG, + OMAP24XX_GR_MOD, OMAP24XX_PRCM_CLKCFG_CTRL_OFFSET); wmb(); } @@ -723,6 +742,184 @@ int omap2_clk_set_parent(struct clk *clk, struct clk *new_parent) return 0; } +/* DPLL rate rounding code */ + +/** + * omap2_dpll_set_rate_tolerance: set the error tolerance during rate rounding + * @clk: struct clk * of the DPLL + * @tolerance: maximum rate error tolerance + * + * Set the maximum DPLL rate error tolerance for the rate rounding + * algorithm. The rate tolerance is an attempt to balance DPLL power + * saving (the least divider value "n") vs. rate fidelity (the least + * difference between the desired DPLL target rate and the rounded + * rate out of the algorithm). So, increasing the tolerance is likely + * to decrease DPLL power consumption and increase DPLL rate error. + * Returns -EINVAL if provided a null clock ptr or a clk that is not a + * DPLL; or 0 upon success. + */ +int omap2_dpll_set_rate_tolerance(struct clk *clk, unsigned int tolerance) +{ + if (!clk || !clk->dpll_data) + return -EINVAL; + + clk->dpll_data->rate_tolerance = tolerance; + + return 0; +} + +static unsigned long _dpll_compute_new_rate(unsigned long parent_rate, unsigned int m, unsigned int n) +{ + unsigned long long num; + + num = (unsigned long long)parent_rate * m; + do_div(num, n); + return num; +} + +/* + * _dpll_test_mult - test a DPLL multiplier value + * @m: pointer to the DPLL m (multiplier) value under test + * @n: current DPLL n (divider) value under test + * @new_rate: pointer to storage for the resulting rounded rate + * @target_rate: the desired DPLL rate + * @parent_rate: the DPLL's parent clock rate + * + * This code tests a DPLL multiplier value, ensuring that the + * resulting rate will not be higher than the target_rate, and that + * the multiplier value itself is valid for the DPLL. Initially, the + * integer pointed to by the m argument should be prescaled by + * multiplying by DPLL_SCALE_FACTOR. The code will replace this with + * a non-scaled m upon return. This non-scaled m will result in a + * new_rate as close as possible to target_rate (but not greater than + * target_rate) given the current (parent_rate, n, prescaled m) + * triple. Returns DPLL_MULT_UNDERFLOW in the event that the + * non-scaled m attempted to underflow, which can allow the calling + * function to bail out early; or 0 upon success. + */ +static int _dpll_test_mult(int *m, int n, unsigned long *new_rate, + unsigned long target_rate, + unsigned long parent_rate) +{ + int flags = 0, carry = 0; + + /* Unscale m and round if necessary */ + if (*m % DPLL_SCALE_FACTOR >= DPLL_ROUNDING_VAL) + carry = 1; + *m = (*m / DPLL_SCALE_FACTOR) + carry; + + /* + * The new rate must be <= the target rate to avoid programming + * a rate that is impossible for the hardware to handle + */ + *new_rate = _dpll_compute_new_rate(parent_rate, *m, n); + if (*new_rate > target_rate) { + (*m)--; + *new_rate = 0; + } + + /* Guard against m underflow */ + if (*m < DPLL_MIN_MULTIPLIER) { + *m = DPLL_MIN_MULTIPLIER; + *new_rate = 0; + flags = DPLL_MULT_UNDERFLOW; + } + + if (*new_rate == 0) + *new_rate = _dpll_compute_new_rate(parent_rate, *m, n); + + return flags; +} + +/** + * omap2_dpll_round_rate - round a target rate for an OMAP DPLL + * @clk: struct clk * for a DPLL + * @target_rate: desired DPLL clock rate + * + * Given a DPLL, a desired target rate, and a rate tolerance, round + * the target rate to a possible, programmable rate for this DPLL. + * Rate tolerance is assumed to be set by the caller before this + * function is called. Attempts to select the minimum possible n + * within the tolerance to reduce power consumption. Stores the + * computed (m, n) in the DPLL's dpll_data structure so set_rate() + * will not need to call this (expensive) function again. Returns ~0 + * if the target rate cannot be rounded, either because the rate is + * too low or because the rate tolerance is set too tightly; or the + * rounded rate upon success. + */ +long omap2_dpll_round_rate(struct clk *clk, unsigned long target_rate) +{ + int m, n, r, e, scaled_max_m; + unsigned long scaled_rt_rp, new_rate; + int min_e = -1, min_e_m = -1, min_e_n = -1; + + if (!clk || !clk->dpll_data) + return ~0; + + pr_debug("clock: starting DPLL round_rate for clock %s, target rate " + "%ld\n", clk->name, target_rate); + + scaled_rt_rp = target_rate / (clk->parent->rate / DPLL_SCALE_FACTOR); + scaled_max_m = clk->dpll_data->max_multiplier * DPLL_SCALE_FACTOR; + + clk->dpll_data->last_rounded_rate = 0; + + for (n = clk->dpll_data->max_divider; n >= DPLL_MIN_DIVIDER; n--) { + + /* Compute the scaled DPLL multiplier, based on the divider */ + m = scaled_rt_rp * n; + + /* + * Since we're counting n down, a m overflow means we can + * can immediately skip to the next n + */ + if (m > scaled_max_m) + continue; + + r = _dpll_test_mult(&m, n, &new_rate, target_rate, + clk->parent->rate); + + e = target_rate - new_rate; + pr_debug("clock: n = %d: m = %d: rate error is %d " + "(new_rate = %ld)\n", n, m, e, new_rate); + + if (min_e == -1 || + min_e >= (int)(abs(e) - clk->dpll_data->rate_tolerance)) { + min_e = e; + min_e_m = m; + min_e_n = n; + + pr_debug("clock: found new least error %d\n", min_e); + } + + /* + * Since we're counting n down, a m underflow means we + * can bail out completely (since as n decreases in + * the next iteration, there's no way that m can + * increase beyond the current m) + */ + if (r & DPLL_MULT_UNDERFLOW) + break; + } + + if (min_e < 0) { + pr_debug("clock: error: target rate or tolerance too low\n"); + return ~0; + } + + clk->dpll_data->last_rounded_m = min_e_m; + clk->dpll_data->last_rounded_n = min_e_n; + clk->dpll_data->last_rounded_rate = + _dpll_compute_new_rate(clk->parent->rate, min_e_m, min_e_n); + + pr_debug("clock: final least error: e = %d, m = %d, n = %d\n", + min_e, min_e_m, min_e_n); + pr_debug("clock: final rate: %ld (target rate: %ld)\n", + clk->dpll_data->last_rounded_rate, target_rate); + + return clk->dpll_data->last_rounded_rate; +} + /*------------------------------------------------------------------------- * Omap2 clock reset and init functions *-------------------------------------------------------------------------*/ diff --git a/arch/arm/mach-omap2/clock.h b/arch/arm/mach-omap2/clock.h index d5980a9e09a..3cd37cb57c5 100644 --- a/arch/arm/mach-omap2/clock.h +++ b/arch/arm/mach-omap2/clock.h @@ -18,11 +18,16 @@ #include <asm/arch/clock.h> +/* The maximum error between a target DPLL rate and the rounded rate in Hz */ +#define DEFAULT_DPLL_RATE_TOLERANCE 50000 + int omap2_clk_enable(struct clk *clk); void omap2_clk_disable(struct clk *clk); long omap2_clk_round_rate(struct clk *clk, unsigned long rate); int omap2_clk_set_rate(struct clk *clk, unsigned long rate); int omap2_clk_set_parent(struct clk *clk, struct clk *new_parent); +int omap2_dpll_rate_tolerance_set(struct clk *clk, unsigned int tolerance); +long omap2_dpll_round_rate(struct clk *clk, unsigned long target_rate); #ifdef CONFIG_OMAP_RESET_CLOCKS void omap2_clk_disable_unused(struct clk *clk); @@ -42,6 +47,7 @@ long omap2_clksel_round_rate(struct clk *clk, unsigned long target_rate); int omap2_clksel_set_rate(struct clk *clk, unsigned long rate); u32 omap2_get_dpll_rate(struct clk *clk); int omap2_wait_clock_ready(void __iomem *reg, u32 cval, const char *name); +void omap2_clk_prepare_for_reboot(void); extern u8 cpu_mask; diff --git a/arch/arm/mach-omap2/clock24xx.c b/arch/arm/mach-omap2/clock24xx.c index ece32d8acba..aa567876651 100644 --- a/arch/arm/mach-omap2/clock24xx.c +++ b/arch/arm/mach-omap2/clock24xx.c @@ -154,7 +154,7 @@ static void omap2_clk_fixed_disable(struct clk *clk) * Uses the current prcm set to tell if a rate is valid. * You can go slower, but not faster within a given rate set. */ -static u32 omap2_dpll_round_rate(unsigned long target_rate) +long omap2_dpllcore_round_rate(unsigned long target_rate) { u32 high, low, core_clk_src; @@ -183,14 +183,14 @@ static u32 omap2_dpll_round_rate(unsigned long target_rate) } -static void omap2_dpll_recalc(struct clk *clk) +static void omap2_dpllcore_recalc(struct clk *clk) { clk->rate = omap2_get_dpll_rate_24xx(clk); propagate_rate(clk); } -static int omap2_reprogram_dpll(struct clk *clk, unsigned long rate) +static int omap2_reprogram_dpllcore(struct clk *clk, unsigned long rate) { u32 cur_rate, low, mult, div, valid_rate, done_rate; u32 bypass = 0; @@ -209,7 +209,7 @@ static int omap2_reprogram_dpll(struct clk *clk, unsigned long rate) } else if ((rate == (cur_rate * 2)) && (mult == 1)) { omap2_reprogram_sdrc(CORE_CLK_SRC_DPLL_X2, 1); } else if (rate != cur_rate) { - valid_rate = omap2_dpll_round_rate(rate); + valid_rate = omap2_dpllcore_round_rate(rate); if (valid_rate != rate) goto dpll_exit; @@ -256,7 +256,7 @@ static int omap2_reprogram_dpll(struct clk *clk, unsigned long rate) omap2_init_memory_params(omap2_dll_force_needed()); omap2_reprogram_sdrc(done_rate, 0); } - omap2_dpll_recalc(&dpll_ck); + omap2_dpllcore_recalc(&dpll_ck); ret = 0; dpll_exit: @@ -383,7 +383,7 @@ static int omap2_select_table_rate(struct clk *clk, unsigned long rate) local_irq_restore(flags); } - omap2_dpll_recalc(&dpll_ck); + omap2_dpllcore_recalc(&dpll_ck); return 0; } diff --git a/arch/arm/mach-omap2/clock24xx.h b/arch/arm/mach-omap2/clock24xx.h index 88081ed13f9..be4e25554e0 100644 --- a/arch/arm/mach-omap2/clock24xx.h +++ b/arch/arm/mach-omap2/clock24xx.h @@ -30,12 +30,12 @@ static long omap2_round_to_table_rate(struct clk *clk, unsigned long rate); static void omap2_sys_clk_recalc(struct clk *clk); static void omap2_osc_clk_recalc(struct clk *clk); static void omap2_sys_clk_recalc(struct clk *clk); -static void omap2_dpll_recalc(struct clk *clk); +static void omap2_dpllcore_recalc(struct clk *clk); static int omap2_clk_fixed_enable(struct clk *clk); static void omap2_clk_fixed_disable(struct clk *clk); static int omap2_enable_osc_ck(struct clk *clk); static void omap2_disable_osc_ck(struct clk *clk); -static int omap2_reprogram_dpll(struct clk *clk, unsigned long rate); +static int omap2_reprogram_dpllcore(struct clk *clk, unsigned long rate); /* Key dividers which make up a PRCM set. Ratio's for a PRCM are mandated. * xtal_speed, dpll_speed, mpu_speed, CM_CLKSEL_MPU,CM_CLKSEL_DSP @@ -665,20 +665,27 @@ static struct clk alt_ck = { /* Typical 54M or 48M, may not exist */ * deal with this */ -static const struct dpll_data dpll_dd = { +static struct dpll_data dpll_dd = { .mult_div1_reg = OMAP_CM_REGADDR(PLL_MOD, CM_CLKSEL1), .mult_mask = OMAP24XX_DPLL_MULT_MASK, .div1_mask = OMAP24XX_DPLL_DIV_MASK, + .max_multiplier = 1024, + .max_divider = 16, + .rate_tolerance = DEFAULT_DPLL_RATE_TOLERANCE }; +/* + * XXX Cannot add round_rate here yet, as this is still a composite clock, + * not just a DPLL + */ static struct clk dpll_ck = { .name = "dpll_ck", .parent = &sys_ck, /* Can be func_32k also */ .dpll_data = &dpll_dd, .flags = CLOCK_IN_OMAP242X | CLOCK_IN_OMAP243X | RATE_PROPAGATES | ALWAYS_ENABLED, - .recalc = &omap2_dpll_recalc, - .set_rate = &omap2_reprogram_dpll, + .recalc = &omap2_dpllcore_recalc, + .set_rate = &omap2_reprogram_dpllcore, }; static struct clk apll96_ck = { @@ -1747,7 +1754,8 @@ static struct clk gpt12_fck = { }; static struct clk mcbsp1_ick = { - .name = "mcbsp1_ick", + .name = "mcbsp_ick", + .id = 1, .parent = &l4_ck, .flags = CLOCK_IN_OMAP242X | CLOCK_IN_OMAP243X, .enable_reg = OMAP_CM_REGADDR(CORE_MOD, CM_ICLKEN1), @@ -1756,7 +1764,8 @@ static struct clk mcbsp1_ick = { }; static struct clk mcbsp1_fck = { - .name = "mcbsp1_fck", + .name = "mcbsp_fck", + .id = 1, .parent = &func_96m_ck, .flags = CLOCK_IN_OMAP242X | CLOCK_IN_OMAP243X, .enable_reg = OMAP_CM_REGADDR(CORE_MOD, CM_FCLKEN1), @@ -1765,7 +1774,8 @@ static struct clk mcbsp1_fck = { }; static struct clk mcbsp2_ick = { - .name = "mcbsp2_ick", + .name = "mcbsp_ick", + .id = 2, .parent = &l4_ck, .flags = CLOCK_IN_OMAP242X | CLOCK_IN_OMAP243X, .enable_reg = OMAP_CM_REGADDR(CORE_MOD, CM_ICLKEN1), @@ -1774,7 +1784,8 @@ static struct clk mcbsp2_ick = { }; static struct clk mcbsp2_fck = { - .name = "mcbsp2_fck", + .name = "mcbsp_fck", + .id = 2, .parent = &func_96m_ck, .flags = CLOCK_IN_OMAP242X | CLOCK_IN_OMAP243X, .enable_reg = OMAP_CM_REGADDR(CORE_MOD, CM_FCLKEN1), @@ -1783,7 +1794,8 @@ static struct clk mcbsp2_fck = { }; static struct clk mcbsp3_ick = { - .name = "mcbsp3_ick", + .name = "mcbsp_ick", + .id = 3, .parent = &l4_ck, .flags = CLOCK_IN_OMAP243X, .enable_reg = OMAP_CM_REGADDR(CORE_MOD, CM_ICLKEN2), @@ -1792,7 +1804,8 @@ static struct clk mcbsp3_ick = { }; static struct clk mcbsp3_fck = { - .name = "mcbsp3_fck", + .name = "mcbsp_fck", + .id = 3, .parent = &func_96m_ck, .flags = CLOCK_IN_OMAP243X, .enable_reg = OMAP_CM_REGADDR(CORE_MOD, OMAP24XX_CM_FCLKEN2), @@ -1801,7 +1814,8 @@ static struct clk mcbsp3_fck = { }; static struct clk mcbsp4_ick = { - .name = "mcbsp4_ick", + .name = "mcbsp_ick", + .id = 4, .parent = &l4_ck, .flags = CLOCK_IN_OMAP243X, .enable_reg = OMAP_CM_REGADDR(CORE_MOD, CM_ICLKEN2), @@ -1810,7 +1824,8 @@ static struct clk mcbsp4_ick = { }; static struct clk mcbsp4_fck = { - .name = "mcbsp4_fck", + .name = "mcbsp_fck", + .id = 4, .parent = &func_96m_ck, .flags = CLOCK_IN_OMAP243X, .enable_reg = OMAP_CM_REGADDR(CORE_MOD, OMAP24XX_CM_FCLKEN2), @@ -1819,7 +1834,8 @@ static struct clk mcbsp4_fck = { }; static struct clk mcbsp5_ick = { - .name = "mcbsp5_ick", + .name = "mcbsp_ick", + .id = 5, .parent = &l4_ck, .flags = CLOCK_IN_OMAP243X, .enable_reg = OMAP_CM_REGADDR(CORE_MOD, CM_ICLKEN2), @@ -1828,7 +1844,8 @@ static struct clk mcbsp5_ick = { }; static struct clk mcbsp5_fck = { - .name = "mcbsp5_fck", + .name = "mcbsp_fck", + .id = 5, .parent = &func_96m_ck, .flags = CLOCK_IN_OMAP243X, .enable_reg = OMAP_CM_REGADDR(CORE_MOD, OMAP24XX_CM_FCLKEN2), diff --git a/arch/arm/mach-omap2/clock34xx.c b/arch/arm/mach-omap2/clock34xx.c index b42bdd6079a..4263099b1ad 100644 --- a/arch/arm/mach-omap2/clock34xx.c +++ b/arch/arm/mach-omap2/clock34xx.c @@ -1,10 +1,11 @@ /* * OMAP3-specific clock framework functions * - * Copyright (C) 2007 Texas Instruments, Inc. - * Copyright (C) 2007 Nokia Corporation + * Copyright (C) 2007-2008 Texas Instruments, Inc. + * Copyright (C) 2007-2008 Nokia Corporation * * Written by Paul Walmsley + * Testing and integration fixes by Jouni Högander * * Parts of this code are based on code written by * Richard Woodruff, Tony Lindgren, Tuukka Tikkanen, Karthik Dasu @@ -23,6 +24,7 @@ #include <linux/delay.h> #include <linux/clk.h> #include <linux/io.h> +#include <linux/limits.h> #include <asm/arch/clock.h> #include <asm/arch/sram.h> @@ -37,8 +39,11 @@ #include "cm.h" #include "cm-regbits-34xx.h" -/* CM_CLKEN_PLL*.EN* bit values */ -#define DPLL_LOCKED 0x7 +/* CM_AUTOIDLE_PLL*.AUTO_* bit values */ +#define DPLL_AUTOIDLE_DISABLE 0x0 +#define DPLL_AUTOIDLE_LOW_POWER_STOP 0x1 + +#define MAX_DPLL_WAIT_TRIES 1000000 /** * omap3_dpll_recalc - recalculate DPLL rate @@ -53,6 +58,290 @@ static void omap3_dpll_recalc(struct clk *clk) propagate_rate(clk); } +/* _omap3_dpll_write_clken - write clken_bits arg to a DPLL's enable bits */ +static void _omap3_dpll_write_clken(struct clk *clk, u8 clken_bits) +{ + const struct dpll_data *dd; + + dd = clk->dpll_data; + + cm_rmw_reg_bits(dd->enable_mask, clken_bits << __ffs(dd->enable_mask), + dd->control_reg); +} + +/* _omap3_wait_dpll_status: wait for a DPLL to enter a specific state */ +static int _omap3_wait_dpll_status(struct clk *clk, u8 state) +{ + const struct dpll_data *dd; + int i = 0; + int ret = -EINVAL; + u32 idlest_mask; + + dd = clk->dpll_data; + + state <<= dd->idlest_bit; + idlest_mask = 1 << dd->idlest_bit; + + while (((cm_read_reg(dd->idlest_reg) & idlest_mask) != state) && + i < MAX_DPLL_WAIT_TRIES) { + i++; + udelay(1); + } + + if (i == MAX_DPLL_WAIT_TRIES) { + printk(KERN_ERR "clock: %s failed transition to '%s'\n", + clk->name, (state) ? "locked" : "bypassed"); + } else { + pr_debug("clock: %s transition to '%s' in %d loops\n", + clk->name, (state) ? "locked" : "bypassed", i); + + ret = 0; + } + + return ret; +} + +/* Non-CORE DPLL (e.g., DPLLs that do not control SDRC) clock functions */ + +/* + * _omap3_noncore_dpll_lock - instruct a DPLL to lock and wait for readiness + * @clk: pointer to a DPLL struct clk + * + * Instructs a non-CORE DPLL to lock. Waits for the DPLL to report + * readiness before returning. Will save and restore the DPLL's + * autoidle state across the enable, per the CDP code. If the DPLL + * locked successfully, return 0; if the DPLL did not lock in the time + * allotted, or DPLL3 was passed in, return -EINVAL. + */ +static int _omap3_noncore_dpll_lock(struct clk *clk) +{ + u8 ai; + int r; + + if (clk == &dpll3_ck) + return -EINVAL; + + pr_debug("clock: locking DPLL %s\n", clk->name); + + ai = omap3_dpll_autoidle_read(clk); + + _omap3_dpll_write_clken(clk, DPLL_LOCKED); + + if (ai) { + /* + * If no downstream clocks are enabled, CM_IDLEST bit + * may never become active, so don't wait for DPLL to lock. + */ + r = 0; + omap3_dpll_allow_idle(clk); + } else { + r = _omap3_wait_dpll_status(clk, 1); + omap3_dpll_deny_idle(clk); + }; + + return r; +} + +/* + * omap3_noncore_dpll_bypass - instruct a DPLL to bypass and wait for readiness + * @clk: pointer to a DPLL struct clk + * + * Instructs a non-CORE DPLL to enter low-power bypass mode. In + * bypass mode, the DPLL's rate is set equal to its parent clock's + * rate. Waits for the DPLL to report readiness before returning. + * Will save and restore the DPLL's autoidle state across the enable, + * per the CDP code. If the DPLL entered bypass mode successfully, + * return 0; if the DPLL did not enter bypass in the time allotted, or + * DPLL3 was passed in, or the DPLL does not support low-power bypass, + * return -EINVAL. + */ +static int _omap3_noncore_dpll_bypass(struct clk *clk) +{ + int r; + u8 ai; + + if (clk == &dpll3_ck) + return -EINVAL; + + if (!(clk->dpll_data->modes & (1 << DPLL_LOW_POWER_BYPASS))) + return -EINVAL; + + pr_debug("clock: configuring DPLL %s for low-power bypass\n", + clk->name); + + ai = omap3_dpll_autoidle_read(clk); + + _omap3_dpll_write_clken(clk, DPLL_LOW_POWER_BYPASS); + + r = _omap3_wait_dpll_status(clk, 0); + + if (ai) + omap3_dpll_allow_idle(clk); + else + omap3_dpll_deny_idle(clk); + + return r; +} + +/* + * _omap3_noncore_dpll_stop - instruct a DPLL to stop + * @clk: pointer to a DPLL struct clk + * + * Instructs a non-CORE DPLL to enter low-power stop. Will save and + * restore the DPLL's autoidle state across the stop, per the CDP + * code. If DPLL3 was passed in, or the DPLL does not support + * low-power stop, return -EINVAL; otherwise, return 0. + */ +static int _omap3_noncore_dpll_stop(struct clk *clk) +{ + u8 ai; + + if (clk == &dpll3_ck) + return -EINVAL; + + if (!(clk->dpll_data->modes & (1 << DPLL_LOW_POWER_STOP))) + return -EINVAL; + + pr_debug("clock: stopping DPLL %s\n", clk->name); + + ai = omap3_dpll_autoidle_read(clk); + + _omap3_dpll_write_clken(clk, DPLL_LOW_POWER_STOP); + + if (ai) + omap3_dpll_allow_idle(clk); + else + omap3_dpll_deny_idle(clk); + + return 0; +} + +/** + * omap3_noncore_dpll_enable - instruct a DPLL to enter bypass or lock mode + * @clk: pointer to a DPLL struct clk + * + * Instructs a non-CORE DPLL to enable, e.g., to enter bypass or lock. + * The choice of modes depends on the DPLL's programmed rate: if it is + * the same as the DPLL's parent clock, it will enter bypass; + * otherwise, it will enter lock. This code will wait for the DPLL to + * indicate readiness before returning, unless the DPLL takes too long + * to enter the target state. Intended to be used as the struct clk's + * enable function. If DPLL3 was passed in, or the DPLL does not + * support low-power stop, or if the DPLL took too long to enter + * bypass or lock, return -EINVAL; otherwise, return 0. + */ +static int omap3_noncore_dpll_enable(struct clk *clk) +{ + int r; + + if (clk == &dpll3_ck) + return -EINVAL; + + if (clk->parent->rate == clk_get_rate(clk)) + r = _omap3_noncore_dpll_bypass(clk); + else + r = _omap3_noncore_dpll_lock(clk); + + return r; +} + +/** + * omap3_noncore_dpll_enable - instruct a DPLL to enter bypass or lock mode + * @clk: pointer to a DPLL struct clk + * + * Instructs a non-CORE DPLL to enable, e.g., to enter bypass or lock. + * The choice of modes depends on the DPLL's programmed rate: if it is + * the same as the DPLL's parent clock, it will enter bypass; + * otherwise, it will enter lock. This code will wait for the DPLL to + * indicate readiness before returning, unless the DPLL takes too long + * to enter the target state. Intended to be used as the struct clk's + * enable function. If DPLL3 was passed in, or the DPLL does not + * support low-power stop, or if the DPLL took too long to enter + * bypass or lock, return -EINVAL; otherwise, return 0. + */ +static void omap3_noncore_dpll_disable(struct clk *clk) +{ + if (clk == &dpll3_ck) + return; + + _omap3_noncore_dpll_stop(clk); +} + +/** + * omap3_dpll_autoidle_read - read a DPLL's autoidle bits + * @clk: struct clk * of the DPLL to read + * + * Return the DPLL's autoidle bits, shifted down to bit 0. Returns + * -EINVAL if passed a null pointer or if the struct clk does not + * appear to refer to a DPLL. + */ +static u32 omap3_dpll_autoidle_read(struct clk *clk) +{ + const struct dpll_data *dd; + u32 v; + + if (!clk || !clk->dpll_data) + return -EINVAL; + + dd = clk->dpll_data; + + v = cm_read_reg(dd->autoidle_reg); + v &= dd->autoidle_mask; + v >>= __ffs(dd->autoidle_mask); + + return v; +} + +/** + * omap3_dpll_allow_idle - enable DPLL autoidle bits + * @clk: struct clk * of the DPLL to operate on + * + * Enable DPLL automatic idle control. This automatic idle mode + * switching takes effect only when the DPLL is locked, at least on + * OMAP3430. The DPLL will enter low-power stop when its downstream + * clocks are gated. No return value. + */ +static void omap3_dpll_allow_idle(struct clk *clk) +{ + const struct dpll_data *dd; + + if (!clk || !clk->dpll_data) + return; + + dd = clk->dpll_data; + + /* + * REVISIT: CORE DPLL can optionally enter low-power bypass + * by writing 0x5 instead of 0x1. Add some mechanism to + * optionally enter this mode. + */ + cm_rmw_reg_bits(dd->autoidle_mask, + DPLL_AUTOIDLE_LOW_POWER_STOP << __ffs(dd->autoidle_mask), + dd->autoidle_reg); +} + +/** + * omap3_dpll_deny_idle - prevent DPLL from automatically idling + * @clk: struct clk * of the DPLL to operate on + * + * Disable DPLL automatic idle control. No return value. + */ +static void omap3_dpll_deny_idle(struct clk *clk) +{ + const struct dpll_data *dd; + + if (!clk || !clk->dpll_data) + return; + + dd = clk->dpll_data; + + cm_rmw_reg_bits(dd->autoidle_mask, + DPLL_AUTOIDLE_DISABLE << __ffs(dd->autoidle_mask), + dd->autoidle_reg); +} + +/* Clock control for DPLL outputs */ + /** * omap3_clkoutx2_recalc - recalculate DPLL X2 output virtual clock rate * @clk: DPLL output struct clk @@ -89,6 +378,8 @@ static void omap3_clkoutx2_recalc(struct clk *clk) propagate_rate(clk); } +/* Common clock code */ + /* * As it is structured now, this will prevent an OMAP2/3 multiboot * kernel from compiling. This will need further attention. diff --git a/arch/arm/mach-omap2/clock34xx.h b/arch/arm/mach-omap2/clock34xx.h index c9c5972a2e2..05757eb032b 100644 --- a/arch/arm/mach-omap2/clock34xx.h +++ b/arch/arm/mach-omap2/clock34xx.h @@ -1,14 +1,19 @@ /* * OMAP3 clock framework * - * Virtual clocks are introduced as a convenient tools. - * They are sources for other clocks and not supposed - * to be requested from drivers directly. - * * Copyright (C) 2007-2008 Texas Instruments, Inc. * Copyright (C) 2007-2008 Nokia Corporation * * Written by Paul Walmsley + * With many device clock fixes by Kevin Hilman and Jouni Högander + * DPLL bypass clock support added by Roman Tereshonkov + * + */ + +/* + * Virtual clocks are introduced as convenient tools. + * They are sources for other clocks and not supposed + * to be requested from drivers directly. */ #ifndef __ARCH_ARM_MACH_OMAP2_CLOCK34XX_H @@ -24,6 +29,15 @@ static void omap3_dpll_recalc(struct clk *clk); static void omap3_clkoutx2_recalc(struct clk *clk); +static void omap3_dpll_allow_idle(struct clk *clk); +static void omap3_dpll_deny_idle(struct clk *clk); +static u32 omap3_dpll_autoidle_read(struct clk *clk); +static int omap3_noncore_dpll_enable(struct clk *clk); +static void omap3_noncore_dpll_disable(struct clk *clk); + +/* Maximum DPLL multiplier, divider values for OMAP3 */ +#define OMAP3_MAX_DPLL_MULT 2048 +#define OMAP3_MAX_DPLL_DIV 128 /* * DPLL1 supplies clock to the MPU. @@ -33,6 +47,11 @@ static void omap3_clkoutx2_recalc(struct clk *clk); * DPLL5 supplies other peripheral clocks (USBHOST, USIM). */ +/* CM_CLKEN_PLL*.EN* bit values - not all are available for every DPLL */ +#define DPLL_LOW_POWER_STOP 0x1 +#define DPLL_LOW_POWER_BYPASS 0x5 +#define DPLL_LOCKED 0x7 + /* PRM CLOCKS */ /* According to timer32k.c, this is a 32768Hz clock, not a 32000Hz clock. */ @@ -240,15 +259,23 @@ static const struct clksel_rate div16_dpll_rates[] = { /* DPLL1 */ /* MPU clock source */ /* Type: DPLL */ -static const struct dpll_data dpll1_dd = { +static struct dpll_data dpll1_dd = { .mult_div1_reg = OMAP_CM_REGADDR(MPU_MOD, OMAP3430_CM_CLKSEL1_PLL), .mult_mask = OMAP3430_MPU_DPLL_MULT_MASK, .div1_mask = OMAP3430_MPU_DPLL_DIV_MASK, .control_reg = OMAP_CM_REGADDR(MPU_MOD, OMAP3430_CM_CLKEN_PLL), .enable_mask = OMAP3430_EN_MPU_DPLL_MASK, + .modes = (1 << DPLL_LOW_POWER_BYPASS) | (1 << DPLL_LOCKED), .auto_recal_bit = OMAP3430_EN_MPU_DPLL_DRIFTGUARD_SHIFT, .recal_en_bit = OMAP3430_MPU_DPLL_RECAL_EN_SHIFT, .recal_st_bit = OMAP3430_MPU_DPLL_ST_SHIFT, + .autoidle_reg = OMAP_CM_REGADDR(MPU_MOD, OMAP3430_CM_AUTOIDLE_PLL), + .autoidle_mask = OMAP3430_AUTO_MPU_DPLL_MASK, + .idlest_reg = OMAP_CM_REGADDR(MPU_MOD, OMAP3430_CM_IDLEST_PLL), + .idlest_bit = OMAP3430_ST_MPU_CLK_SHIFT, + .max_multiplier = OMAP3_MAX_DPLL_MULT, + .max_divider = OMAP3_MAX_DPLL_DIV, + .rate_tolerance = DEFAULT_DPLL_RATE_TOLERANCE }; static struct clk dpll1_ck = { @@ -256,6 +283,7 @@ static struct clk dpll1_ck = { .parent = &sys_ck, .dpll_data = &dpll1_dd, .flags = CLOCK_IN_OMAP343X | RATE_PROPAGATES | ALWAYS_ENABLED, + .round_rate = &omap2_dpll_round_rate, .recalc = &omap3_dpll_recalc, }; @@ -297,22 +325,34 @@ static struct clk dpll1_x2m2_ck = { /* IVA2 clock source */ /* Type: DPLL */ -static const struct dpll_data dpll2_dd = { +static struct dpll_data dpll2_dd = { .mult_div1_reg = OMAP_CM_REGADDR(OMAP3430_IVA2_MOD, OMAP3430_CM_CLKSEL1_PLL), .mult_mask = OMAP3430_IVA2_DPLL_MULT_MASK, .div1_mask = OMAP3430_IVA2_DPLL_DIV_MASK, .control_reg = OMAP_CM_REGADDR(OMAP3430_IVA2_MOD, OMAP3430_CM_CLKEN_PLL), .enable_mask = OMAP3430_EN_IVA2_DPLL_MASK, + .modes = (1 << DPLL_LOW_POWER_STOP) | (1 << DPLL_LOCKED) | + (1 << DPLL_LOW_POWER_BYPASS), .auto_recal_bit = OMAP3430_EN_IVA2_DPLL_DRIFTGUARD_SHIFT, .recal_en_bit = OMAP3430_PRM_IRQENABLE_MPU_IVA2_DPLL_RECAL_EN_SHIFT, .recal_st_bit = OMAP3430_PRM_IRQSTATUS_MPU_IVA2_DPLL_ST_SHIFT, + .autoidle_reg = OMAP_CM_REGADDR(OMAP3430_IVA2_MOD, OMAP3430_CM_AUTOIDLE_PLL), + .autoidle_mask = OMAP3430_AUTO_IVA2_DPLL_MASK, + .idlest_reg = OMAP_CM_REGADDR(OMAP3430_IVA2_MOD, OMAP3430_CM_IDLEST_PLL), + .idlest_bit = OMAP3430_ST_IVA2_CLK_SHIFT, + .max_multiplier = OMAP3_MAX_DPLL_MULT, + .max_divider = OMAP3_MAX_DPLL_DIV, + .rate_tolerance = DEFAULT_DPLL_RATE_TOLERANCE }; static struct clk dpll2_ck = { .name = "dpll2_ck", .parent = &sys_ck, .dpll_data = &dpll2_dd, - .flags = CLOCK_IN_OMAP343X | RATE_PROPAGATES | ALWAYS_ENABLED, + .flags = CLOCK_IN_OMAP343X | RATE_PROPAGATES, + .enable = &omap3_noncore_dpll_enable, + .disable = &omap3_noncore_dpll_disable, + .round_rate = &omap2_dpll_round_rate, .recalc = &omap3_dpll_recalc, }; @@ -338,10 +378,12 @@ static struct clk dpll2_m2_ck = { .recalc = &omap2_clksel_recalc, }; -/* DPLL3 */ -/* Source clock for all interfaces and for some device fclks */ -/* Type: DPLL */ -static const struct dpll_data dpll3_dd = { +/* + * DPLL3 + * Source clock for all interfaces and for some device fclks + * REVISIT: Also supports fast relock bypass - not included below + */ +static struct dpll_data dpll3_dd = { .mult_div1_reg = OMAP_CM_REGADDR(PLL_MOD, CM_CLKSEL1), .mult_mask = OMAP3430_CORE_DPLL_MULT_MASK, .div1_mask = OMAP3430_CORE_DPLL_DIV_MASK, @@ -350,6 +392,11 @@ static const struct dpll_data dpll3_dd = { .auto_recal_bit = OMAP3430_EN_CORE_DPLL_DRIFTGUARD_SHIFT, .recal_en_bit = OMAP3430_CORE_DPLL_RECAL_EN_SHIFT, .recal_st_bit = OMAP3430_CORE_DPLL_ST_SHIFT, + .autoidle_reg = OMAP_CM_REGADDR(PLL_MOD, CM_AUTOIDLE), + .autoidle_mask = OMAP3430_AUTO_CORE_DPLL_MASK, + .max_multiplier = OMAP3_MAX_DPLL_MULT, + .max_divider = OMAP3_MAX_DPLL_DIV, + .rate_tolerance = DEFAULT_DPLL_RATE_TOLERANCE }; static struct clk dpll3_ck = { @@ -357,6 +404,7 @@ static struct clk dpll3_ck = { .parent = &sys_ck, .dpll_data = &dpll3_dd, .flags = CLOCK_IN_OMAP343X | RATE_PROPAGATES | ALWAYS_ENABLED, + .round_rate = &omap2_dpll_round_rate, .recalc = &omap3_dpll_recalc, }; @@ -439,7 +487,7 @@ static struct clk core_ck = { .name = "core_ck", .init = &omap2_init_clksel_parent, .clksel_reg = OMAP_CM_REGADDR(PLL_MOD, CM_IDLEST), - .clksel_mask = OMAP3430_ST_CORE_CLK, + .clksel_mask = OMAP3430_ST_CORE_CLK_MASK, .clksel = core_ck_clksel, .flags = CLOCK_IN_OMAP343X | RATE_PROPAGATES | PARENT_CONTROLS_CLOCK, @@ -456,7 +504,7 @@ static struct clk dpll3_m2x2_ck = { .name = "dpll3_m2x2_ck", .init = &omap2_init_clksel_parent, .clksel_reg = OMAP_CM_REGADDR(PLL_MOD, CM_IDLEST), - .clksel_mask = OMAP3430_ST_CORE_CLK, + .clksel_mask = OMAP3430_ST_CORE_CLK_MASK, .clksel = dpll3_m2x2_ck_clksel, .flags = CLOCK_IN_OMAP343X | RATE_PROPAGATES | PARENT_CONTROLS_CLOCK, @@ -503,7 +551,7 @@ static struct clk emu_core_alwon_ck = { .parent = &dpll3_m3x2_ck, .init = &omap2_init_clksel_parent, .clksel_reg = OMAP_CM_REGADDR(PLL_MOD, CM_IDLEST), - .clksel_mask = OMAP3430_ST_CORE_CLK, + .clksel_mask = OMAP3430_ST_CORE_CLK_MASK, .clksel = emu_core_alwon_ck_clksel, .flags = CLOCK_IN_OMAP343X | RATE_PROPAGATES | PARENT_CONTROLS_CLOCK, @@ -513,22 +561,33 @@ static struct clk emu_core_alwon_ck = { /* DPLL4 */ /* Supplies 96MHz, 54Mhz TV DAC, DSS fclk, CAM sensor clock, emul trace clk */ /* Type: DPLL */ -static const struct dpll_data dpll4_dd = { +static struct dpll_data dpll4_dd = { .mult_div1_reg = OMAP_CM_REGADDR(PLL_MOD, CM_CLKSEL2), .mult_mask = OMAP3430_PERIPH_DPLL_MULT_MASK, .div1_mask = OMAP3430_PERIPH_DPLL_DIV_MASK, .control_reg = OMAP_CM_REGADDR(PLL_MOD, CM_CLKEN), .enable_mask = OMAP3430_EN_PERIPH_DPLL_MASK, + .modes = (1 << DPLL_LOW_POWER_STOP) | (1 << DPLL_LOCKED), .auto_recal_bit = OMAP3430_EN_PERIPH_DPLL_DRIFTGUARD_SHIFT, .recal_en_bit = OMAP3430_PERIPH_DPLL_RECAL_EN_SHIFT, .recal_st_bit = OMAP3430_PERIPH_DPLL_ST_SHIFT, + .autoidle_reg = OMAP_CM_REGADDR(PLL_MOD, CM_AUTOIDLE), + .autoidle_mask = OMAP3430_AUTO_PERIPH_DPLL_MASK, + .idlest_reg = OMAP_CM_REGADDR(PLL_MOD, CM_IDLEST), + .idlest_bit = OMAP3430_ST_PERIPH_CLK_SHIFT, + .max_multiplier = OMAP3_MAX_DPLL_MULT, + .max_divider = OMAP3_MAX_DPLL_DIV, + .rate_tolerance = DEFAULT_DPLL_RATE_TOLERANCE }; static struct clk dpll4_ck = { .name = "dpll4_ck", .parent = &sys_ck, .dpll_data = &dpll4_dd, - .flags = CLOCK_IN_OMAP343X | RATE_PROPAGATES | ALWAYS_ENABLED, + .flags = CLOCK_IN_OMAP343X | RATE_PROPAGATES, + .enable = &omap3_noncore_dpll_enable, + .disable = &omap3_noncore_dpll_disable, + .round_rate = &omap2_dpll_round_rate, .recalc = &omap3_dpll_recalc, }; @@ -584,7 +643,7 @@ static struct clk omap_96m_alwon_fck = { .parent = &dpll4_m2x2_ck, .init = &omap2_init_clksel_parent, .clksel_reg = OMAP_CM_REGADDR(PLL_MOD, CM_IDLEST), - .clksel_mask = OMAP3430_ST_PERIPH_CLK, + .clksel_mask = OMAP3430_ST_PERIPH_CLK_MASK, .clksel = omap_96m_alwon_fck_clksel, .flags = CLOCK_IN_OMAP343X | RATE_PROPAGATES | PARENT_CONTROLS_CLOCK, @@ -610,7 +669,7 @@ static struct clk cm_96m_fck = { .parent = &dpll4_m2x2_ck, .init = &omap2_init_clksel_parent, .clksel_reg = OMAP_CM_REGADDR(PLL_MOD, CM_IDLEST), - .clksel_mask = OMAP3430_ST_PERIPH_CLK, + .clksel_mask = OMAP3430_ST_PERIPH_CLK_MASK, .clksel = cm_96m_fck_clksel, .flags = CLOCK_IN_OMAP343X | RATE_PROPAGATES | PARENT_CONTROLS_CLOCK, @@ -652,7 +711,7 @@ static struct clk virt_omap_54m_fck = { .parent = &dpll4_m3x2_ck, .init = &omap2_init_clksel_parent, .clksel_reg = OMAP_CM_REGADDR(PLL_MOD, CM_IDLEST), - .clksel_mask = OMAP3430_ST_PERIPH_CLK, + .clksel_mask = OMAP3430_ST_PERIPH_CLK_MASK, .clksel = virt_omap_54m_fck_clksel, .flags = CLOCK_IN_OMAP343X | RATE_PROPAGATES | PARENT_CONTROLS_CLOCK, @@ -804,23 +863,33 @@ static struct clk emu_per_alwon_ck = { /* Supplies 120MHz clock, USIM source clock */ /* Type: DPLL */ /* 3430ES2 only */ -static const struct dpll_data dpll5_dd = { +static struct dpll_data dpll5_dd = { .mult_div1_reg = OMAP_CM_REGADDR(PLL_MOD, OMAP3430ES2_CM_CLKSEL4), .mult_mask = OMAP3430ES2_PERIPH2_DPLL_MULT_MASK, .div1_mask = OMAP3430ES2_PERIPH2_DPLL_DIV_MASK, .control_reg = OMAP_CM_REGADDR(PLL_MOD, OMAP3430ES2_CM_CLKEN2), .enable_mask = OMAP3430ES2_EN_PERIPH2_DPLL_MASK, + .modes = (1 << DPLL_LOW_POWER_STOP) | (1 << DPLL_LOCKED), .auto_recal_bit = OMAP3430ES2_EN_PERIPH2_DPLL_DRIFTGUARD_SHIFT, .recal_en_bit = OMAP3430ES2_SND_PERIPH_DPLL_RECAL_EN_SHIFT, .recal_st_bit = OMAP3430ES2_SND_PERIPH_DPLL_ST_SHIFT, + .autoidle_reg = OMAP_CM_REGADDR(PLL_MOD, OMAP3430ES2_CM_AUTOIDLE2_PLL), + .autoidle_mask = OMAP3430ES2_AUTO_PERIPH2_DPLL_MASK, + .idlest_reg = OMAP_CM_REGADDR(PLL_MOD, CM_IDLEST2), + .idlest_bit = OMAP3430ES2_ST_PERIPH2_CLK_SHIFT, + .max_multiplier = OMAP3_MAX_DPLL_MULT, + .max_divider = OMAP3_MAX_DPLL_DIV, + .rate_tolerance = DEFAULT_DPLL_RATE_TOLERANCE }; static struct clk dpll5_ck = { .name = "dpll5_ck", .parent = &sys_ck, .dpll_data = &dpll5_dd, - .flags = CLOCK_IN_OMAP3430ES2 | RATE_PROPAGATES | - ALWAYS_ENABLED, + .flags = CLOCK_IN_OMAP3430ES2 | RATE_PROPAGATES, + .enable = &omap3_noncore_dpll_enable, + .disable = &omap3_noncore_dpll_disable, + .round_rate = &omap2_dpll_round_rate, .recalc = &omap3_dpll_recalc, }; @@ -1365,7 +1434,8 @@ static const struct clksel mcbsp_15_clksel[] = { }; static struct clk mcbsp5_fck = { - .name = "mcbsp5_fck", + .name = "mcbsp_fck", + .id = 5, .init = &omap2_init_clksel_parent, .enable_reg = OMAP_CM_REGADDR(CORE_MOD, CM_FCLKEN1), .enable_bit = OMAP3430_EN_MCBSP5_SHIFT, @@ -1377,7 +1447,8 @@ static struct clk mcbsp5_fck = { }; static struct clk mcbsp1_fck = { - .name = "mcbsp1_fck", + .name = "mcbsp_fck", + .id = 1, .init = &omap2_init_clksel_parent, .enable_reg = OMAP_CM_REGADDR(CORE_MOD, CM_FCLKEN1), .enable_bit = OMAP3430_EN_MCBSP1_SHIFT, @@ -1789,7 +1860,8 @@ static struct clk gpt10_ick = { }; static struct clk mcbsp5_ick = { - .name = "mcbsp5_ick", + .name = "mcbsp_ick", + .id = 5, .parent = &core_l4_ick, .enable_reg = OMAP_CM_REGADDR(CORE_MOD, CM_ICLKEN1), .enable_bit = OMAP3430_EN_MCBSP5_SHIFT, @@ -1798,7 +1870,8 @@ static struct clk mcbsp5_ick = { }; static struct clk mcbsp1_ick = { - .name = "mcbsp1_ick", + .name = "mcbsp_ick", + .id = 1, .parent = &core_l4_ick, .enable_reg = OMAP_CM_REGADDR(CORE_MOD, CM_ICLKEN1), .enable_bit = OMAP3430_EN_MCBSP1_SHIFT, @@ -1935,7 +2008,7 @@ static struct clk dss1_alwon_fck = { .enable_reg = OMAP_CM_REGADDR(OMAP3430_DSS_MOD, CM_FCLKEN), .enable_bit = OMAP3430_EN_DSS1_SHIFT, .clksel_reg = OMAP_CM_REGADDR(PLL_MOD, CM_IDLEST), - .clksel_mask = OMAP3430_ST_PERIPH_CLK, + .clksel_mask = OMAP3430_ST_PERIPH_CLK_MASK, .clksel = dss1_alwon_fck_clksel, .flags = CLOCK_IN_OMAP343X, .recalc = &omap2_clksel_recalc, @@ -1991,7 +2064,7 @@ static struct clk cam_mclk = { .parent = &dpll4_m5x2_ck, .init = &omap2_init_clksel_parent, .clksel_reg = OMAP_CM_REGADDR(PLL_MOD, CM_IDLEST), - .clksel_mask = OMAP3430_ST_PERIPH_CLK, + .clksel_mask = OMAP3430_ST_PERIPH_CLK_MASK, .clksel = cam_mclk_clksel, .enable_reg = OMAP_CM_REGADDR(OMAP3430_CAM_MOD, CM_FCLKEN), .enable_bit = OMAP3430_EN_CAM_SHIFT, @@ -2541,7 +2614,8 @@ static struct clk gpt2_ick = { }; static struct clk mcbsp2_ick = { - .name = "mcbsp2_ick", + .name = "mcbsp_ick", + .id = 2, .parent = &per_l4_ick, .enable_reg = OMAP_CM_REGADDR(OMAP3430_PER_MOD, CM_ICLKEN), .enable_bit = OMAP3430_EN_MCBSP2_SHIFT, @@ -2550,7 +2624,8 @@ static struct clk mcbsp2_ick = { }; static struct clk mcbsp3_ick = { - .name = "mcbsp3_ick", + .name = "mcbsp_ick", + .id = 3, .parent = &per_l4_ick, .enable_reg = OMAP_CM_REGADDR(OMAP3430_PER_MOD, CM_ICLKEN), .enable_bit = OMAP3430_EN_MCBSP3_SHIFT, @@ -2559,7 +2634,8 @@ static struct clk mcbsp3_ick = { }; static struct clk mcbsp4_ick = { - .name = "mcbsp4_ick", + .name = "mcbsp_ick", + .id = 4, .parent = &per_l4_ick, .enable_reg = OMAP_CM_REGADDR(OMAP3430_PER_MOD, CM_ICLKEN), .enable_bit = OMAP3430_EN_MCBSP4_SHIFT, @@ -2574,7 +2650,8 @@ static const struct clksel mcbsp_234_clksel[] = { }; static struct clk mcbsp2_fck = { - .name = "mcbsp2_fck", + .name = "mcbsp_fck", + .id = 2, .init = &omap2_init_clksel_parent, .enable_reg = OMAP_CM_REGADDR(OMAP3430_PER_MOD, CM_FCLKEN), .enable_bit = OMAP3430_EN_MCBSP2_SHIFT, @@ -2586,7 +2663,8 @@ static struct clk mcbsp2_fck = { }; static struct clk mcbsp3_fck = { - .name = "mcbsp3_fck", + .name = "mcbsp_fck", + .id = 3, .init = &omap2_init_clksel_parent, .enable_reg = OMAP_CM_REGADDR(OMAP3430_PER_MOD, CM_FCLKEN), .enable_bit = OMAP3430_EN_MCBSP3_SHIFT, @@ -2598,7 +2676,8 @@ static struct clk mcbsp3_fck = { }; static struct clk mcbsp4_fck = { - .name = "mcbsp4_fck", + .name = "mcbsp_fck", + .id = 4, .init = &omap2_init_clksel_parent, .enable_reg = OMAP_CM_REGADDR(OMAP3430_PER_MOD, CM_FCLKEN), .enable_bit = OMAP3430_EN_MCBSP4_SHIFT, diff --git a/arch/arm/mach-omap2/cm-regbits-34xx.h b/arch/arm/mach-omap2/cm-regbits-34xx.h index 3c38395f644..ee4c0ca1a70 100644 --- a/arch/arm/mach-omap2/cm-regbits-34xx.h +++ b/arch/arm/mach-omap2/cm-regbits-34xx.h @@ -72,7 +72,8 @@ #define OMAP3430_ST_IVA2 (1 << 0) /* CM_IDLEST_PLL_IVA2 */ -#define OMAP3430_ST_IVA2_CLK (1 << 0) +#define OMAP3430_ST_IVA2_CLK_SHIFT 0 +#define OMAP3430_ST_IVA2_CLK_MASK (1 << 0) /* CM_AUTOIDLE_PLL_IVA2 */ #define OMAP3430_AUTO_IVA2_DPLL_SHIFT 0 @@ -115,10 +116,7 @@ #define OMAP3430_ST_MPU (1 << 0) /* CM_IDLEST_PLL_MPU */ -#define OMAP3430_ST_MPU_CLK (1 << 0) -#define OMAP3430_ST_IVA2_CLK_MASK (1 << 0) - -/* CM_IDLEST_PLL_MPU */ +#define OMAP3430_ST_MPU_CLK_SHIFT 0 #define OMAP3430_ST_MPU_CLK_MASK (1 << 0) /* CM_AUTOIDLE_PLL_MPU */ @@ -408,8 +406,10 @@ #define OMAP3430_ST_12M_CLK (1 << 4) #define OMAP3430_ST_48M_CLK (1 << 3) #define OMAP3430_ST_96M_CLK (1 << 2) -#define OMAP3430_ST_PERIPH_CLK (1 << 1) -#define OMAP3430_ST_CORE_CLK (1 << 0) +#define OMAP3430_ST_PERIPH_CLK_SHIFT 1 +#define OMAP3430_ST_PERIPH_CLK_MASK (1 << 1) +#define OMAP3430_ST_CORE_CLK_SHIFT 0 +#define OMAP3430_ST_CORE_CLK_MASK (1 << 0) /* CM_IDLEST2_CKGEN */ #define OMAP3430ES2_ST_120M_CLK_SHIFT 1 @@ -423,6 +423,10 @@ #define OMAP3430_AUTO_CORE_DPLL_SHIFT 0 #define OMAP3430_AUTO_CORE_DPLL_MASK (0x7 << 0) +/* CM_AUTOIDLE2_PLL */ +#define OMAP3430ES2_AUTO_PERIPH2_DPLL_SHIFT 0 +#define OMAP3430ES2_AUTO_PERIPH2_DPLL_MASK (0x7 << 0) + /* CM_CLKSEL1_PLL */ /* Note that OMAP3430_CORE_DPLL_CLKOUT_DIV_MASK was (0x3 << 27) on 3430ES1 */ #define OMAP3430_CORE_DPLL_CLKOUT_DIV_SHIFT 27 diff --git a/arch/arm/mach-omap2/cm.h b/arch/arm/mach-omap2/cm.h index 8489f3029fe..87a44c715aa 100644 --- a/arch/arm/mach-omap2/cm.h +++ b/arch/arm/mach-omap2/cm.h @@ -81,6 +81,7 @@ #define OMAP3430ES2_CM_FCLKEN3 0x0008 #define OMAP3430_CM_IDLEST_PLL CM_IDLEST2 #define OMAP3430_CM_AUTOIDLE_PLL CM_AUTOIDLE2 +#define OMAP3430ES2_CM_AUTOIDLE2_PLL CM_AUTOIDLE2 #define OMAP3430_CM_CLKSEL1 CM_CLKSEL #define OMAP3430_CM_CLKSEL1_PLL CM_CLKSEL #define OMAP3430_CM_CLKSEL2_PLL CM_CLKSEL2 @@ -96,15 +97,21 @@ /* Clock management domain register get/set */ #ifndef __ASSEMBLER__ -static inline void cm_write_mod_reg(u32 val, s16 module, s16 idx) + +extern u32 cm_read_mod_reg(s16 module, u16 idx); +extern void cm_write_mod_reg(u32 val, s16 module, u16 idx); +extern u32 cm_rmw_mod_reg_bits(u32 mask, u32 bits, s16 module, s16 idx); + +static inline u32 cm_set_mod_reg_bits(u32 bits, s16 module, s16 idx) { - __raw_writel(val, OMAP_CM_REGADDR(module, idx)); + return cm_rmw_mod_reg_bits(bits, bits, module, idx); } -static inline u32 cm_read_mod_reg(s16 module, s16 idx) +static inline u32 cm_clear_mod_reg_bits(u32 bits, s16 module, s16 idx) { - return __raw_readl(OMAP_CM_REGADDR(module, idx)); + return cm_rmw_mod_reg_bits(bits, 0x0, module, idx); } + #endif /* CM register bits shared between 24XX and 3430 */ diff --git a/arch/arm/mach-omap2/control.c b/arch/arm/mach-omap2/control.c index a5d86a49c21..51f70300996 100644 --- a/arch/arm/mach-omap2/control.c +++ b/arch/arm/mach-omap2/control.c @@ -13,22 +13,21 @@ #undef DEBUG #include <linux/kernel.h> +#include <linux/io.h> -#include <asm/io.h> - +#include <asm/arch/common.h> #include <asm/arch/control.h> -static u32 omap2_ctrl_base; +static void __iomem *omap2_ctrl_base; -#define OMAP_CTRL_REGADDR(reg) (void __iomem *)IO_ADDRESS(omap2_ctrl_base \ - + (reg)) +#define OMAP_CTRL_REGADDR(reg) (omap2_ctrl_base + (reg)) -void omap_ctrl_base_set(u32 base) +void __init omap2_set_globals_control(struct omap_globals *omap2_globals) { - omap2_ctrl_base = base; + omap2_ctrl_base = omap2_globals->ctrl; } -u32 omap_ctrl_base_get(void) +void __iomem *omap_ctrl_base_get(void) { return omap2_ctrl_base; } @@ -50,25 +49,16 @@ u32 omap_ctrl_readl(u16 offset) void omap_ctrl_writeb(u8 val, u16 offset) { - pr_debug("omap_ctrl_writeb: writing 0x%0x to 0x%0x\n", val, - (u32)OMAP_CTRL_REGADDR(offset)); - __raw_writeb(val, OMAP_CTRL_REGADDR(offset)); } void omap_ctrl_writew(u16 val, u16 offset) { - pr_debug("omap_ctrl_writew: writing 0x%0x to 0x%0x\n", val, - (u32)OMAP_CTRL_REGADDR(offset)); - __raw_writew(val, OMAP_CTRL_REGADDR(offset)); } void omap_ctrl_writel(u32 val, u16 offset) { - pr_debug("omap_ctrl_writel: writing 0x%0x to 0x%0x\n", val, - (u32)OMAP_CTRL_REGADDR(offset)); - __raw_writel(val, OMAP_CTRL_REGADDR(offset)); } diff --git a/arch/arm/mach-omap2/id.c b/arch/arm/mach-omap2/id.c index 4dfd878d796..dff4b16cead 100644 --- a/arch/arm/mach-omap2/id.c +++ b/arch/arm/mach-omap2/id.c @@ -17,16 +17,23 @@ #include <asm/io.h> -#if defined(CONFIG_ARCH_OMAP2420) -#define OMAP24XX_TAP_BASE io_p2v(0x48014000) -#endif +#include <asm/arch/control.h> +#include <asm/arch/cpu.h> -#if defined(CONFIG_ARCH_OMAP2430) -#define OMAP24XX_TAP_BASE io_p2v(0x4900A000) +#if defined(CONFIG_ARCH_OMAP2420) +#define TAP_BASE io_p2v(0x48014000) +#elif defined(CONFIG_ARCH_OMAP2430) +#define TAP_BASE io_p2v(0x4900A000) +#elif defined(CONFIG_ARCH_OMAP34XX) +#define TAP_BASE io_p2v(0x4830A000) #endif #define OMAP_TAP_IDCODE 0x0204 +#if defined(CONFIG_ARCH_OMAP34XX) +#define OMAP_TAP_PROD_ID 0x0210 +#else #define OMAP_TAP_PROD_ID 0x0208 +#endif #define OMAP_TAP_DIE_ID_0 0x0218 #define OMAP_TAP_DIE_ID_1 0x021C @@ -56,9 +63,134 @@ static struct omap_id omap_ids[] __initdata = { { .hawkeye = 0xb68a, .dev = 0x0, .type = 0x24300000 }, }; +static struct omap_chip_id omap_chip; + +/** + * omap_chip_is - test whether currently running OMAP matches a chip type + * @oc: omap_chip_t to test against + * + * Test whether the currently-running OMAP chip matches the supplied + * chip type 'oc'. Returns 1 upon a match; 0 upon failure. + */ +int omap_chip_is(struct omap_chip_id oci) +{ + return (oci.oc & omap_chip.oc) ? 1 : 0; +} +EXPORT_SYMBOL(omap_chip_is); + static u32 __init read_tap_reg(int reg) { - return __raw_readl(OMAP24XX_TAP_BASE + reg); + unsigned int regval = 0; + u32 cpuid; + + /* Reading the IDCODE register on 3430 ES1 results in a + * data abort as the register is not exposed on the OCP + * Hence reading the Cortex Rev + */ + cpuid = read_cpuid(CPUID_ID); + + /* If the processor type is Cortex-A8 and the revision is 0x0 + * it means its Cortex r0p0 which is 3430 ES1 + */ + if ((((cpuid >> 4) & 0xFFF) == 0xC08) && ((cpuid & 0xF) == 0x0)) { + switch (reg) { + case OMAP_TAP_IDCODE : regval = 0x0B7AE02F; break; + /* Making DevType as 0xF in ES1 to differ from ES2 */ + case OMAP_TAP_PROD_ID : regval = 0x000F00F0; break; + case OMAP_TAP_DIE_ID_0: regval = 0x01000000; break; + case OMAP_TAP_DIE_ID_1: regval = 0x1012d687; break; + case OMAP_TAP_DIE_ID_2: regval = 0x00000000; break; + case OMAP_TAP_DIE_ID_3: regval = 0x2d2c0000; break; + } + } else + regval = __raw_readl(TAP_BASE + reg); + + return regval; + +} + +/* + * _set_system_rev - set the system_rev global based on current OMAP chip type + * + * Set the system_rev global. This is primarily used by the cpu_is_omapxxxx() + * macros. + */ +static void __init _set_system_rev(u32 type, u8 rev) +{ + u32 i, ctrl_status; + + /* + * system_rev encoding is as follows + * system_rev & 0xff000000 -> Omap Class (24xx/34xx) + * system_rev & 0xfff00000 -> Omap Sub Class (242x/343x) + * system_rev & 0xffff0000 -> Omap type (2420/2422/2423/2430/3430) + * system_rev & 0x0000f000 -> Silicon revision (ES1, ES2 ) + * system_rev & 0x00000700 -> Device Type ( EMU/HS/GP/BAD ) + * system_rev & 0x000000c0 -> IDCODE revision[6:7] + * system_rev & 0x0000003f -> sys_boot[0:5] + */ + /* Embedding the ES revision info in type field */ + system_rev = type; + /* Also add IDCODE revision info only two lower bits */ + system_rev |= ((rev & 0x3) << 6); + + /* Add in the device type and sys_boot fields (see above) */ + if (cpu_is_omap24xx()) { + i = OMAP24XX_CONTROL_STATUS; + } else if (cpu_is_omap343x()) { + i = OMAP343X_CONTROL_STATUS; + } else { + printk(KERN_ERR "id: unknown CPU type\n"); + BUG(); + } + ctrl_status = omap_ctrl_readl(i); + system_rev |= (ctrl_status & (OMAP2_SYSBOOT_5_MASK | + OMAP2_SYSBOOT_4_MASK | + OMAP2_SYSBOOT_3_MASK | + OMAP2_SYSBOOT_2_MASK | + OMAP2_SYSBOOT_1_MASK | + OMAP2_SYSBOOT_0_MASK)); + system_rev |= (ctrl_status & OMAP2_DEVICETYPE_MASK); +} + + +/* + * _set_omap_chip - set the omap_chip global based on OMAP chip type + * + * Build the omap_chip bits. This variable is used by powerdomain and + * clockdomain code to indicate whether structures are applicable for + * the current OMAP chip type by ANDing it against a 'platform' bitfield + * in the structure. + */ +static void __init _set_omap_chip(void) +{ + if (cpu_is_omap343x()) { + + omap_chip.oc = CHIP_IS_OMAP3430; + if (is_sil_rev_equal_to(OMAP3430_REV_ES1_0)) + omap_chip.oc |= CHIP_IS_OMAP3430ES1; + else if (is_sil_rev_greater_than(OMAP3430_REV_ES1_0)) + omap_chip.oc |= CHIP_IS_OMAP3430ES2; + + } else if (cpu_is_omap243x()) { + + /* Currently only supports 2430ES2.1 and 2430-all */ + omap_chip.oc |= CHIP_IS_OMAP2430; + + } else if (cpu_is_omap242x()) { + + /* Currently only supports 2420ES2.1.1 and 2420-all */ + omap_chip.oc |= CHIP_IS_OMAP2420; + + } else { + + /* Current CPU not supported by this code. */ + printk(KERN_WARNING "OMAP chip type code does not yet support " + "this CPU type.\n"); + WARN_ON(1); + + } + } void __init omap2_check_revision(void) @@ -76,21 +208,31 @@ void __init omap2_check_revision(void) rev = (idcode >> 28) & 0x0f; dev_type = (prod_id >> 16) & 0x0f; -#ifdef DEBUG - printk(KERN_DEBUG "OMAP_TAP_IDCODE 0x%08x REV %i HAWKEYE 0x%04x MANF %03x\n", - idcode, rev, hawkeye, (idcode >> 1) & 0x7ff); - printk(KERN_DEBUG "OMAP_TAP_DIE_ID_0: 0x%08x\n", - read_tap_reg(OMAP_TAP_DIE_ID_0)); - printk(KERN_DEBUG "OMAP_TAP_DIE_ID_1: 0x%08x DEV_REV: %i\n", - read_tap_reg(OMAP_TAP_DIE_ID_1), - (read_tap_reg(OMAP_TAP_DIE_ID_1) >> 28) & 0xf); - printk(KERN_DEBUG "OMAP_TAP_DIE_ID_2: 0x%08x\n", - read_tap_reg(OMAP_TAP_DIE_ID_2)); - printk(KERN_DEBUG "OMAP_TAP_DIE_ID_3: 0x%08x\n", - read_tap_reg(OMAP_TAP_DIE_ID_3)); - printk(KERN_DEBUG "OMAP_TAP_PROD_ID_0: 0x%08x DEV_TYPE: %i\n", - prod_id, dev_type); -#endif + pr_debug("OMAP_TAP_IDCODE 0x%08x REV %i HAWKEYE 0x%04x MANF %03x\n", + idcode, rev, hawkeye, (idcode >> 1) & 0x7ff); + pr_debug("OMAP_TAP_DIE_ID_0: 0x%08x\n", + read_tap_reg(OMAP_TAP_DIE_ID_0)); + pr_debug("OMAP_TAP_DIE_ID_1: 0x%08x DEV_REV: %i\n", + read_tap_reg(OMAP_TAP_DIE_ID_1), + (read_tap_reg(OMAP_TAP_DIE_ID_1) >> 28) & 0xf); + pr_debug("OMAP_TAP_DIE_ID_2: 0x%08x\n", + read_tap_reg(OMAP_TAP_DIE_ID_2)); + pr_debug("OMAP_TAP_DIE_ID_3: 0x%08x\n", + read_tap_reg(OMAP_TAP_DIE_ID_3)); + pr_debug("OMAP_TAP_PROD_ID_0: 0x%08x DEV_TYPE: %i\n", + prod_id, dev_type); + + /* + * Detection for 34xx ES2.0 and above can be done with just + * hawkeye and rev. See TRM 1.5.2 Device Identification. + * Note that rev cannot be used directly as ES1.0 uses value 0. + */ + if (hawkeye == 0xb7ae) { + system_rev = 0x34300000 | ((1 + rev) << 12); + pr_info("OMAP%04x ES2.%i\n", system_rev >> 16, rev); + _set_omap_chip(); + return; + } /* Check hawkeye ids */ for (i = 0; i < ARRAY_SIZE(omap_ids); i++) { @@ -114,16 +256,15 @@ void __init omap2_check_revision(void) omap_ids[i].type >> 16); j = i; } - system_rev = omap_ids[j].type; - system_rev |= rev << 8; + _set_system_rev(omap_ids[j].type, rev); - /* Add the cpu class info (24xx) */ - system_rev |= 0x24; + _set_omap_chip(); pr_info("OMAP%04x", system_rev >> 16); if ((system_rev >> 8) & 0x0f) - printk("%x", (system_rev >> 8) & 0x0f); - printk("\n"); + pr_info("ES%x", (system_rev >> 12) & 0xf); + pr_info("\n"); + } diff --git a/arch/arm/mach-omap2/mcbsp.c b/arch/arm/mach-omap2/mcbsp.c new file mode 100644 index 00000000000..17cf199d113 --- /dev/null +++ b/arch/arm/mach-omap2/mcbsp.c @@ -0,0 +1,208 @@ +/* + * linux/arch/arm/mach-omap2/mcbsp.c + * + * Copyright (C) 2008 Instituto Nokia de Tecnologia + * Contact: Eduardo Valentin <eduardo.valentin@indt.org.br> + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + * + * Multichannel mode not supported. + */ +#include <linux/module.h> +#include <linux/init.h> +#include <linux/clk.h> +#include <linux/err.h> +#include <linux/io.h> +#include <linux/platform_device.h> + +#include <asm/arch/dma.h> +#include <asm/arch/mux.h> +#include <asm/arch/cpu.h> +#include <asm/arch/mcbsp.h> + +struct mcbsp_internal_clk { + struct clk clk; + struct clk **childs; + int n_childs; +}; + +#if defined(CONFIG_ARCH_OMAP24XX) || defined(CONFIG_ARCH_OMAP34XX) +static void omap_mcbsp_clk_init(struct mcbsp_internal_clk *mclk) +{ + const char *clk_names[] = { "mcbsp_ick", "mcbsp_fck" }; + int i; + + mclk->n_childs = ARRAY_SIZE(clk_names); + mclk->childs = kzalloc(mclk->n_childs * sizeof(struct clk *), + GFP_KERNEL); + + for (i = 0; i < mclk->n_childs; i++) { + /* We fake a platform device to get correct device id */ + struct platform_device pdev; + + pdev.dev.bus = &platform_bus_type; + pdev.id = mclk->clk.id; + mclk->childs[i] = clk_get(&pdev.dev, clk_names[i]); + if (IS_ERR(mclk->childs[i])) + printk(KERN_ERR "Could not get clock %s (%d).\n", + clk_names[i], mclk->clk.id); + } +} + +static int omap_mcbsp_clk_enable(struct clk *clk) +{ + struct mcbsp_internal_clk *mclk = container_of(clk, + struct mcbsp_internal_clk, clk); + int i; + + for (i = 0; i < mclk->n_childs; i++) + clk_enable(mclk->childs[i]); + return 0; +} + +static void omap_mcbsp_clk_disable(struct clk *clk) +{ + struct mcbsp_internal_clk *mclk = container_of(clk, + struct mcbsp_internal_clk, clk); + int i; + + for (i = 0; i < mclk->n_childs; i++) + clk_disable(mclk->childs[i]); +} + +static struct mcbsp_internal_clk omap_mcbsp_clks[] = { + { + .clk = { + .name = "mcbsp_clk", + .id = 1, + .enable = omap_mcbsp_clk_enable, + .disable = omap_mcbsp_clk_disable, + }, + }, + { + .clk = { + .name = "mcbsp_clk", + .id = 2, + .enable = omap_mcbsp_clk_enable, + .disable = omap_mcbsp_clk_disable, + }, + }, +}; + +#define omap_mcbsp_clks_size ARRAY_SIZE(omap_mcbsp_clks) +#else +#define omap_mcbsp_clks_size 0 +static struct mcbsp_internal_clk __initdata *omap_mcbsp_clks; +static inline void omap_mcbsp_clk_init(struct clk *clk) +{ } +#endif + +static void omap2_mcbsp2_mux_setup(void) +{ + omap_cfg_reg(Y15_24XX_MCBSP2_CLKX); + omap_cfg_reg(R14_24XX_MCBSP2_FSX); + omap_cfg_reg(W15_24XX_MCBSP2_DR); + omap_cfg_reg(V15_24XX_MCBSP2_DX); + omap_cfg_reg(V14_24XX_GPIO117); + /* + * TODO: Need to add MUX settings for OMAP 2430 SDP + */ +} + +static void omap2_mcbsp_request(unsigned int id) +{ + if (cpu_is_omap2420() && (id == OMAP_MCBSP2)) + omap2_mcbsp2_mux_setup(); +} + +static int omap2_mcbsp_check(unsigned int id) +{ + if (id > OMAP_MAX_MCBSP_COUNT - 1) { + printk(KERN_ERR "OMAP-McBSP: McBSP%d doesn't exist\n", id + 1); + return -ENODEV; + } + return 0; +} + +static struct omap_mcbsp_ops omap2_mcbsp_ops = { + .request = omap2_mcbsp_request, + .check = omap2_mcbsp_check, +}; + +#ifdef CONFIG_ARCH_OMAP24XX +static struct omap_mcbsp_platform_data omap24xx_mcbsp_pdata[] = { + { + .virt_base = IO_ADDRESS(OMAP24XX_MCBSP1_BASE), + .dma_rx_sync = OMAP24XX_DMA_MCBSP1_RX, + .dma_tx_sync = OMAP24XX_DMA_MCBSP1_TX, + .rx_irq = INT_24XX_MCBSP1_IRQ_RX, + .tx_irq = INT_24XX_MCBSP1_IRQ_TX, + .ops = &omap2_mcbsp_ops, + .clk_name = "mcbsp_clk", + }, + { + .virt_base = IO_ADDRESS(OMAP24XX_MCBSP2_BASE), + .dma_rx_sync = OMAP24XX_DMA_MCBSP2_RX, + .dma_tx_sync = OMAP24XX_DMA_MCBSP2_TX, + .rx_irq = INT_24XX_MCBSP2_IRQ_RX, + .tx_irq = INT_24XX_MCBSP2_IRQ_TX, + .ops = &omap2_mcbsp_ops, + .clk_name = "mcbsp_clk", + }, +}; +#define OMAP24XX_MCBSP_PDATA_SZ ARRAY_SIZE(omap24xx_mcbsp_pdata) +#else +#define omap24xx_mcbsp_pdata NULL +#define OMAP24XX_MCBSP_PDATA_SZ 0 +#endif + +#ifdef CONFIG_ARCH_OMAP34XX +static struct omap_mcbsp_platform_data omap34xx_mcbsp_pdata[] = { + { + .virt_base = IO_ADDRESS(OMAP34XX_MCBSP1_BASE), + .dma_rx_sync = OMAP24XX_DMA_MCBSP1_RX, + .dma_tx_sync = OMAP24XX_DMA_MCBSP1_TX, + .rx_irq = INT_24XX_MCBSP1_IRQ_RX, + .tx_irq = INT_24XX_MCBSP1_IRQ_TX, + .ops = &omap2_mcbsp_ops, + .clk_name = "mcbsp_clk", + }, + { + .virt_base = IO_ADDRESS(OMAP34XX_MCBSP2_BASE), + .dma_rx_sync = OMAP24XX_DMA_MCBSP2_RX, + .dma_tx_sync = OMAP24XX_DMA_MCBSP2_TX, + .rx_irq = INT_24XX_MCBSP2_IRQ_RX, + .tx_irq = INT_24XX_MCBSP2_IRQ_TX, + .ops = &omap2_mcbsp_ops, + .clk_name = "mcbsp_clk", + }, +}; +#define OMAP34XX_MCBSP_PDATA_SZ ARRAY_SIZE(omap34xx_mcbsp_pdata) +#else +#define omap34xx_mcbsp_pdata NULL +#define OMAP34XX_MCBSP_PDATA_SZ 0 +#endif + +int __init omap2_mcbsp_init(void) +{ + int i; + + for (i = 0; i < omap_mcbsp_clks_size; i++) { + /* Once we call clk_get inside init, we do not register it */ + omap_mcbsp_clk_init(&omap_mcbsp_clks[i]); + clk_register(&omap_mcbsp_clks[i].clk); + } + + if (cpu_is_omap24xx()) + omap_mcbsp_register_board_cfg(omap24xx_mcbsp_pdata, + OMAP24XX_MCBSP_PDATA_SZ); + + if (cpu_is_omap34xx()) + omap_mcbsp_register_board_cfg(omap34xx_mcbsp_pdata, + OMAP34XX_MCBSP_PDATA_SZ); + + return omap_mcbsp_init(); +} +arch_initcall(omap2_mcbsp_init); diff --git a/arch/arm/mach-omap2/memory.c b/arch/arm/mach-omap2/memory.c index 12479081881..73cadb2c75c 100644 --- a/arch/arm/mach-omap2/memory.c +++ b/arch/arm/mach-omap2/memory.c @@ -24,6 +24,7 @@ #include <asm/io.h> +#include <asm/arch/common.h> #include <asm/arch/clock.h> #include <asm/arch/sram.h> @@ -32,8 +33,8 @@ #include "memory.h" #include "sdrc.h" -unsigned long omap2_sdrc_base; -unsigned long omap2_sms_base; +void __iomem *omap2_sdrc_base; +void __iomem *omap2_sms_base; static struct memory_timings mem_timings; static u32 curr_perf_level = CORE_CLK_SRC_DPLL_X2; @@ -154,6 +155,12 @@ void omap2_init_memory_params(u32 force_lock_to_unlock_mode) mem_timings.slow_dll_ctrl |= ((1 << 1) | (3 << 8)); } +void __init omap2_set_globals_memory(struct omap_globals *omap2_globals) +{ + omap2_sdrc_base = omap2_globals->sdrc; + omap2_sms_base = omap2_globals->sms; +} + /* turn on smart idle modes for SDRAM scheduler and controller */ void __init omap2_init_memory(void) { diff --git a/arch/arm/mach-omap2/mux.c b/arch/arm/mach-omap2/mux.c index 930770012a7..8f98b20f30a 100644 --- a/arch/arm/mach-omap2/mux.c +++ b/arch/arm/mach-omap2/mux.c @@ -236,7 +236,7 @@ void __init_or_module omap2_cfg_debug(const struct pin_config *cfg, u8 reg) warn = (orig != reg); if (debug || warn) printk(KERN_WARNING - "MUX: setup %s (0x%08x): 0x%02x -> 0x%02x\n", + "MUX: setup %s (0x%p): 0x%04x -> 0x%04x\n", cfg->name, omap_ctrl_base_get() + cfg->mux_reg, orig, reg); } diff --git a/arch/arm/mach-omap2/pm.c b/arch/arm/mach-omap2/pm.c index aad781dcf1b..d6c9de82ca0 100644 --- a/arch/arm/mach-omap2/pm.c +++ b/arch/arm/mach-omap2/pm.c @@ -57,13 +57,6 @@ void omap2_pm_idle(void) return; } - /* - * Since an interrupt may set up a timer, we don't want to - * reprogram the hardware timer with interrupts enabled. - * Re-enable interrupts only after returning from idle. - */ - timer_dyn_reprogram(); - omap2_sram_idle(); local_fiq_enable(); local_irq_enable(); diff --git a/arch/arm/mach-omap2/prcm-common.h b/arch/arm/mach-omap2/prcm-common.h index cacb34086e3..54c32f48213 100644 --- a/arch/arm/mach-omap2/prcm-common.h +++ b/arch/arm/mach-omap2/prcm-common.h @@ -32,6 +32,7 @@ /* Chip-specific module offsets */ +#define OMAP24XX_GR_MOD OCP_MOD #define OMAP24XX_DSP_MOD 0x800 #define OMAP2430_MDM_MOD 0xc00 diff --git a/arch/arm/mach-omap2/prcm.c b/arch/arm/mach-omap2/prcm.c index b12f423b859..fd92a80f38f 100644 --- a/arch/arm/mach-omap2/prcm.c +++ b/arch/arm/mach-omap2/prcm.c @@ -16,16 +16,21 @@ #include <linux/module.h> #include <linux/init.h> #include <linux/clk.h> +#include <linux/io.h> -#include <asm/io.h> +#include <asm/arch/common.h> +#include <asm/arch/prcm.h> +#include "clock.h" #include "prm.h" #include "prm-regbits-24xx.h" -extern void omap2_clk_prepare_for_reboot(void); +static void __iomem *prm_base; +static void __iomem *cm_base; u32 omap_prcm_get_reset_sources(void) { + /* XXX This presumably needs modification for 34XX */ return prm_read_mod_reg(WKUP_MOD, RM_RSTST) & 0x7f; } EXPORT_SYMBOL(omap_prcm_get_reset_sources); @@ -33,11 +38,90 @@ EXPORT_SYMBOL(omap_prcm_get_reset_sources); /* Resets clock rates and reboots the system. Only called from system.h */ void omap_prcm_arch_reset(char mode) { - u32 wkup; + s16 prcm_offs; omap2_clk_prepare_for_reboot(); - if (cpu_is_omap24xx()) { - wkup = prm_read_mod_reg(WKUP_MOD, RM_RSTCTRL) | OMAP_RST_DPLL3; - prm_write_mod_reg(wkup, WKUP_MOD, RM_RSTCTRL); - } + if (cpu_is_omap24xx()) + prcm_offs = WKUP_MOD; + else if (cpu_is_omap34xx()) + prcm_offs = OMAP3430_GR_MOD; + else + WARN_ON(1); + + prm_set_mod_reg_bits(OMAP_RST_DPLL3, prcm_offs, RM_RSTCTRL); +} + +static inline u32 __omap_prcm_read(void __iomem *base, s16 module, u16 reg) +{ + BUG_ON(!base); + return __raw_readl(base + module + reg); +} + +static inline void __omap_prcm_write(u32 value, void __iomem *base, + s16 module, u16 reg) +{ + BUG_ON(!base); + __raw_writel(value, base + module + reg); +} + +/* Read a register in a PRM module */ +u32 prm_read_mod_reg(s16 module, u16 idx) +{ + return __omap_prcm_read(prm_base, module, idx); +} +EXPORT_SYMBOL(prm_read_mod_reg); + +/* Write into a register in a PRM module */ +void prm_write_mod_reg(u32 val, s16 module, u16 idx) +{ + __omap_prcm_write(val, prm_base, module, idx); +} +EXPORT_SYMBOL(prm_write_mod_reg); + +/* Read-modify-write a register in a PRM module. Caller must lock */ +u32 prm_rmw_mod_reg_bits(u32 mask, u32 bits, s16 module, s16 idx) +{ + u32 v; + + v = prm_read_mod_reg(module, idx); + v &= ~mask; + v |= bits; + prm_write_mod_reg(v, module, idx); + + return v; +} +EXPORT_SYMBOL(prm_rmw_mod_reg_bits); + +/* Read a register in a CM module */ +u32 cm_read_mod_reg(s16 module, u16 idx) +{ + return __omap_prcm_read(cm_base, module, idx); +} +EXPORT_SYMBOL(cm_read_mod_reg); + +/* Write into a register in a CM module */ +void cm_write_mod_reg(u32 val, s16 module, u16 idx) +{ + __omap_prcm_write(val, cm_base, module, idx); +} +EXPORT_SYMBOL(cm_write_mod_reg); + +/* Read-modify-write a register in a CM module. Caller must lock */ +u32 cm_rmw_mod_reg_bits(u32 mask, u32 bits, s16 module, s16 idx) +{ + u32 v; + + v = cm_read_mod_reg(module, idx); + v &= ~mask; + v |= bits; + cm_write_mod_reg(v, module, idx); + + return v; +} +EXPORT_SYMBOL(cm_rmw_mod_reg_bits); + +void __init omap2_set_globals_prcm(struct omap_globals *omap2_globals) +{ + prm_base = omap2_globals->prm; + cm_base = omap2_globals->cm; } diff --git a/arch/arm/mach-omap2/prm.h b/arch/arm/mach-omap2/prm.h index 618f8111658..bbf41fc8e9a 100644 --- a/arch/arm/mach-omap2/prm.h +++ b/arch/arm/mach-omap2/prm.h @@ -38,13 +38,29 @@ * */ +/* Global 24xx registers in GR_MOD (Same as OCP_MOD for 24xx) */ +#define OMAP24XX_PRCM_VOLTCTRL_OFFSET 0x0050 +#define OMAP24XX_PRCM_CLKCFG_CTRL_OFFSET 0x0080 + +/* 242x GR_MOD registers, use these only for assembly code */ +#define OMAP242X_PRCM_VOLTCTRL OMAP2420_PRM_REGADDR(OMAP24XX_GR_MOD, \ + OMAP24XX_PRCM_VOLTCTRL_OFFSET) +#define OMAP242X_PRCM_CLKCFG_CTRL OMAP2420_PRM_REGADDR(OMAP24XX_GR_MOD, \ + OMAP24XX_PRCM_CLKCFG_CTRL_OFFSET) + +/* 243x GR_MOD registers, use these only for assembly code */ +#define OMAP243X_PRCM_VOLTCTRL OMAP2430_PRM_REGADDR(OMAP24XX_GR_MOD, \ + OMAP24XX_PRCM_VOLTCTRL_OFFSET) +#define OMAP243X_PRCM_CLKCFG_CTRL OMAP2430_PRM_REGADDR(OMAP24XX_GR_MOD, \ + OMAP24XX_PRCM_CLKCFG_CTRL_OFFSET) + +/* These will disappear */ #define OMAP24XX_PRCM_REVISION OMAP_PRM_REGADDR(OCP_MOD, 0x0000) #define OMAP24XX_PRCM_SYSCONFIG OMAP_PRM_REGADDR(OCP_MOD, 0x0010) #define OMAP24XX_PRCM_IRQSTATUS_MPU OMAP_PRM_REGADDR(OCP_MOD, 0x0018) #define OMAP24XX_PRCM_IRQENABLE_MPU OMAP_PRM_REGADDR(OCP_MOD, 0x001c) -#define OMAP24XX_PRCM_VOLTCTRL OMAP_PRM_REGADDR(OCP_MOD, 0x0050) #define OMAP24XX_PRCM_VOLTST OMAP_PRM_REGADDR(OCP_MOD, 0x0054) #define OMAP24XX_PRCM_CLKSRC_CTRL OMAP_PRM_REGADDR(OCP_MOD, 0x0060) #define OMAP24XX_PRCM_CLKOUT_CTRL OMAP_PRM_REGADDR(OCP_MOD, 0x0070) @@ -150,15 +166,19 @@ #ifndef __ASSEMBLER__ /* Power/reset management domain register get/set */ +extern u32 prm_read_mod_reg(s16 module, u16 idx); +extern void prm_write_mod_reg(u32 val, s16 module, u16 idx); +extern u32 prm_rmw_mod_reg_bits(u32 mask, u32 bits, s16 module, s16 idx); -static inline void prm_write_mod_reg(u32 val, s16 module, s16 idx) +/* Read-modify-write bits in a PRM register (by domain) */ +static inline u32 prm_set_mod_reg_bits(u32 bits, s16 module, s16 idx) { - __raw_writel(val, OMAP_PRM_REGADDR(module, idx)); + return prm_rmw_mod_reg_bits(bits, bits, module, idx); } -static inline u32 prm_read_mod_reg(s16 module, s16 idx) +static inline u32 prm_clear_mod_reg_bits(u32 bits, s16 module, s16 idx) { - return __raw_readl(OMAP_PRM_REGADDR(module, idx)); + return prm_rmw_mod_reg_bits(bits, 0x0, module, idx); } #endif diff --git a/arch/arm/mach-omap2/sdrc.h b/arch/arm/mach-omap2/sdrc.h index d7f23bc9550..1b1fe4f6e03 100644 --- a/arch/arm/mach-omap2/sdrc.h +++ b/arch/arm/mach-omap2/sdrc.h @@ -18,13 +18,11 @@ #include <asm/arch/sdrc.h> #ifndef __ASSEMBLER__ -extern unsigned long omap2_sdrc_base; -extern unsigned long omap2_sms_base; +extern void __iomem *omap2_sdrc_base; +extern void __iomem *omap2_sms_base; -#define OMAP_SDRC_REGADDR(reg) \ - (void __iomem *)IO_ADDRESS(omap2_sdrc_base + (reg)) -#define OMAP_SMS_REGADDR(reg) \ - (void __iomem *)IO_ADDRESS(omap2_sms_base + (reg)) +#define OMAP_SDRC_REGADDR(reg) (omap2_sdrc_base + (reg)) +#define OMAP_SMS_REGADDR(reg) (omap2_sms_base + (reg)) /* SDRC global register get/set */ diff --git a/arch/arm/mach-omap2/sram-fn.S b/arch/arm/mach-omap2/sram242x.S index 4a9e4914071..4c274510f3e 100644 --- a/arch/arm/mach-omap2/sram-fn.S +++ b/arch/arm/mach-omap2/sram242x.S @@ -1,5 +1,5 @@ /* - * linux/arch/arm/mach-omap2/sram-fn.S + * linux/arch/arm/mach-omap2/sram242x.S * * Omap2 specific functions that need to be run in internal SRAM * @@ -27,22 +27,20 @@ #include <asm/arch/io.h> #include <asm/hardware.h> -#include "sdrc.h" #include "prm.h" #include "cm.h" - -#define TIMER_32KSYNCT_CR_V IO_ADDRESS(OMAP2420_32KSYNCT_BASE + 0x010) +#include "sdrc.h" .text -ENTRY(sram_ddr_init) +ENTRY(omap242x_sram_ddr_init) stmfd sp!, {r0 - r12, lr} @ save registers on stack mov r12, r2 @ capture CS1 vs CS0 mov r8, r3 @ capture force parameter /* frequency shift down */ - ldr r2, cm_clksel2_pll @ get address of dpllout reg + ldr r2, omap242x_sdi_cm_clksel2_pll @ get address of dpllout reg mov r3, #0x1 @ value for 1x operation str r3, [r2] @ go to L1-freq operation @@ -51,7 +49,7 @@ ENTRY(sram_ddr_init) bl voltage_shift @ go drop voltage /* dll lock mode */ - ldr r11, sdrc_dlla_ctrl @ addr of dlla ctrl + ldr r11, omap242x_sdi_sdrc_dlla_ctrl @ addr of dlla ctrl ldr r10, [r11] @ get current val cmp r12, #0x1 @ cs1 base (2422 es2.05/1) addeq r11, r11, #0x8 @ if cs1 base, move to DLLB @@ -102,7 +100,7 @@ i_dll_delay: * wait for it to finish, use 32k sync counter, 1tick=31uS. */ voltage_shift: - ldr r4, prcm_voltctrl @ get addr of volt ctrl. + ldr r4, omap242x_sdi_prcm_voltctrl @ get addr of volt ctrl. ldr r5, [r4] @ get value. ldr r6, prcm_mask_val @ get value of mask and r5, r5, r6 @ apply mask to clear bits @@ -112,7 +110,7 @@ voltage_shift: orr r5, r5, r3 @ build value for force str r5, [r4] @ Force transition to L1 - ldr r3, timer_32ksynct_cr @ get addr of counter + ldr r3, omap242x_sdi_timer_32ksynct_cr @ get addr of counter ldr r5, [r3] @ get value add r5, r5, #0x3 @ give it at most 93uS volt_delay: @@ -121,32 +119,31 @@ volt_delay: bhi volt_delay @ not yet->branch mov pc, lr @ back to caller. -/* relative load constants */ -cm_clksel2_pll: +omap242x_sdi_cm_clksel2_pll: .word OMAP2420_CM_REGADDR(PLL_MOD, CM_CLKSEL2) -sdrc_dlla_ctrl: +omap242x_sdi_sdrc_dlla_ctrl: .word OMAP242X_SDRC_REGADDR(SDRC_DLLA_CTRL) -prcm_voltctrl: - .word OMAP2420_PRM_REGADDR(OCP_MOD, 0x50) +omap242x_sdi_prcm_voltctrl: + .word OMAP242X_PRCM_VOLTCTRL prcm_mask_val: .word 0xFFFF3FFC -timer_32ksynct_cr: - .word TIMER_32KSYNCT_CR_V -ENTRY(sram_ddr_init_sz) - .word . - sram_ddr_init +omap242x_sdi_timer_32ksynct_cr: + .word IO_ADDRESS(OMAP2_32KSYNCT_BASE + 0x010) +ENTRY(omap242x_sram_ddr_init_sz) + .word . - omap242x_sram_ddr_init /* * Reprograms memory timings. * r0 = [PRCM_FULL | PRCM_HALF] r1 = SDRC_DLLA_CTRL value r2 = [DDR | SDR] * PRCM_FULL = 2, PRCM_HALF = 1, DDR = 1, SDR = 0 */ -ENTRY(sram_reprogram_sdrc) +ENTRY(omap242x_sram_reprogram_sdrc) stmfd sp!, {r0 - r10, lr} @ save registers on stack mov r3, #0x0 @ clear for mrc call mcr p15, 0, r3, c7, c10, 4 @ memory barrier, finish ARM SDR/DDR nop nop - ldr r6, ddr_sdrc_rfr_ctrl @ get addr of refresh reg + ldr r6, omap242x_srs_sdrc_rfr_ctrl @ get addr of refresh reg ldr r5, [r6] @ get value mov r5, r5, lsr #8 @ isolate rfr field and drop burst @@ -160,7 +157,7 @@ ENTRY(sram_reprogram_sdrc) movne r5, r5, lsl #1 @ mult by 2 if to full mov r5, r5, lsl #8 @ put rfr field back into place add r5, r5, #0x1 @ turn on burst of 1 - ldr r4, ddr_cm_clksel2_pll @ get address of out reg + ldr r4, omap242x_srs_cm_clksel2_pll @ get address of out reg ldr r3, [r4] @ get curr value orr r3, r3, #0x3 bic r3, r3, #0x3 @ clear lower bits @@ -181,7 +178,7 @@ ENTRY(sram_reprogram_sdrc) bne freq_out @ leave if SDR, no DLL function /* With DDR, we need to take care of the DLL for the frequency change */ - ldr r2, ddr_sdrc_dlla_ctrl @ addr of dlla ctrl + ldr r2, omap242x_srs_sdrc_dlla_ctrl @ addr of dlla ctrl str r1, [r2] @ write out new SDRC_DLLA_CTRL add r2, r2, #0x8 @ addr to SDRC_DLLB_CTRL str r1, [r2] @ commit to SDRC_DLLB_CTRL @@ -197,7 +194,7 @@ freq_out: * wait for it to finish, use 32k sync counter, 1tick=31uS. */ voltage_shift_c: - ldr r10, ddr_prcm_voltctrl @ get addr of volt ctrl + ldr r10, omap242x_srs_prcm_voltctrl @ get addr of volt ctrl ldr r8, [r10] @ get value ldr r7, ddr_prcm_mask_val @ get value of mask and r8, r8, r7 @ apply mask to clear bits @@ -207,7 +204,7 @@ voltage_shift_c: orr r8, r8, r7 @ build value for force str r8, [r10] @ Force transition to L1 - ldr r10, ddr_timer_32ksynct @ get addr of counter + ldr r10, omap242x_srs_timer_32ksynct @ get addr of counter ldr r8, [r10] @ get value add r8, r8, #0x2 @ give it at most 62uS (min 31+) volt_delay_c: @@ -216,39 +213,39 @@ volt_delay_c: bhi volt_delay_c @ not yet->branch mov pc, lr @ back to caller -ddr_cm_clksel2_pll: +omap242x_srs_cm_clksel2_pll: .word OMAP2420_CM_REGADDR(PLL_MOD, CM_CLKSEL2) -ddr_sdrc_dlla_ctrl: +omap242x_srs_sdrc_dlla_ctrl: .word OMAP242X_SDRC_REGADDR(SDRC_DLLA_CTRL) -ddr_sdrc_rfr_ctrl: +omap242x_srs_sdrc_rfr_ctrl: .word OMAP242X_SDRC_REGADDR(SDRC_RFR_CTRL_0) -ddr_prcm_voltctrl: - .word OMAP2420_PRM_REGADDR(OCP_MOD, 0x50) +omap242x_srs_prcm_voltctrl: + .word OMAP242X_PRCM_VOLTCTRL ddr_prcm_mask_val: .word 0xFFFF3FFC -ddr_timer_32ksynct: - .word TIMER_32KSYNCT_CR_V +omap242x_srs_timer_32ksynct: + .word IO_ADDRESS(OMAP2_32KSYNCT_BASE + 0x010) -ENTRY(sram_reprogram_sdrc_sz) - .word . - sram_reprogram_sdrc +ENTRY(omap242x_sram_reprogram_sdrc_sz) + .word . - omap242x_sram_reprogram_sdrc /* * Set dividers and pll. Also recalculate DLL value for DDR and unlock mode. */ -ENTRY(sram_set_prcm) +ENTRY(omap242x_sram_set_prcm) stmfd sp!, {r0-r12, lr} @ regs to stack adr r4, pbegin @ addr of preload start adr r8, pend @ addr of preload end mcrr p15, 1, r8, r4, c12 @ preload into icache pbegin: /* move into fast relock bypass */ - ldr r8, pll_ctl @ get addr + ldr r8, omap242x_ssp_pll_ctl @ get addr ldr r5, [r8] @ get val mvn r6, #0x3 @ clear mask and r5, r5, r6 @ clear field orr r7, r5, #0x2 @ fast relock val str r7, [r8] @ go to fast relock - ldr r4, pll_stat @ addr of stat + ldr r4, omap242x_ssp_pll_stat @ addr of stat block: /* wait for bypass */ ldr r8, [r4] @ stat value @@ -257,10 +254,10 @@ block: bne block @ loop if not /* set new dpll dividers _after_ in bypass */ - ldr r4, pll_div @ get addr + ldr r4, omap242x_ssp_pll_div @ get addr str r0, [r4] @ set dpll ctrl val - ldr r4, set_config @ get addr + ldr r4, omap242x_ssp_set_config @ get addr mov r8, #1 @ valid cfg msk str r8, [r4] @ make dividers take @@ -274,8 +271,8 @@ wait_a_bit: beq pend @ jump over dpll relock /* relock DPLL with new vals */ - ldr r5, pll_stat @ get addr - ldr r4, pll_ctl @ get addr + ldr r5, omap242x_ssp_pll_stat @ get addr + ldr r4, omap242x_ssp_pll_ctl @ get addr orr r8, r7, #0x3 @ val for lock dpll str r8, [r4] @ set val mov r0, #1000 @ dead spin a bit @@ -289,9 +286,9 @@ wait_lock: bne wait_lock @ wait if not pend: /* update memory timings & briefly lock dll */ - ldr r4, sdrc_rfr @ get addr + ldr r4, omap242x_ssp_sdrc_rfr @ get addr str r1, [r4] @ update refresh timing - ldr r11, dlla_ctrl @ get addr of DLLA ctrl + ldr r11, omap242x_ssp_dlla_ctrl @ get addr of DLLA ctrl ldr r10, [r11] @ get current val mvn r9, #0x4 @ mask to get clear bit2 and r10, r10, r9 @ clear bit2 for lock mode @@ -307,18 +304,18 @@ wait_dll_lock: nop ldmfd sp!, {r0-r12, pc} @ restore regs and return -set_config: - .word OMAP2420_PRM_REGADDR(OCP_MOD, 0x80) -pll_ctl: - .word OMAP2420_CM_REGADDR(PLL_MOD, CM_FCLKEN1) -pll_stat: - .word OMAP2420_CM_REGADDR(PLL_MOD, CM_IDLEST1) -pll_div: - .word OMAP2420_CM_REGADDR(PLL_MOD, CM_CLKSEL) -sdrc_rfr: +omap242x_ssp_set_config: + .word OMAP242X_PRCM_CLKCFG_CTRL +omap242x_ssp_pll_ctl: + .word OMAP2420_CM_REGADDR(PLL_MOD, CM_CLKEN) +omap242x_ssp_pll_stat: + .word OMAP2420_CM_REGADDR(PLL_MOD, CM_IDLEST) +omap242x_ssp_pll_div: + .word OMAP2420_CM_REGADDR(PLL_MOD, CM_CLKSEL1) +omap242x_ssp_sdrc_rfr: .word OMAP242X_SDRC_REGADDR(SDRC_RFR_CTRL_0) -dlla_ctrl: +omap242x_ssp_dlla_ctrl: .word OMAP242X_SDRC_REGADDR(SDRC_DLLA_CTRL) -ENTRY(sram_set_prcm_sz) - .word . - sram_set_prcm +ENTRY(omap242x_sram_set_prcm_sz) + .word . - omap242x_sram_set_prcm diff --git a/arch/arm/mach-omap2/sram243x.S b/arch/arm/mach-omap2/sram243x.S new file mode 100644 index 00000000000..a3fa48dc08c --- /dev/null +++ b/arch/arm/mach-omap2/sram243x.S @@ -0,0 +1,321 @@ +/* + * linux/arch/arm/mach-omap2/sram243x.S + * + * Omap2 specific functions that need to be run in internal SRAM + * + * (C) Copyright 2004 + * Texas Instruments, <www.ti.com> + * Richard Woodruff <r-woodruff2@ti.com> + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR /PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ +#include <linux/linkage.h> +#include <asm/assembler.h> +#include <asm/arch/io.h> +#include <asm/hardware.h> + +#include "prm.h" +#include "cm.h" +#include "sdrc.h" + + .text + +ENTRY(omap243x_sram_ddr_init) + stmfd sp!, {r0 - r12, lr} @ save registers on stack + + mov r12, r2 @ capture CS1 vs CS0 + mov r8, r3 @ capture force parameter + + /* frequency shift down */ + ldr r2, omap243x_sdi_cm_clksel2_pll @ get address of dpllout reg + mov r3, #0x1 @ value for 1x operation + str r3, [r2] @ go to L1-freq operation + + /* voltage shift down */ + mov r9, #0x1 @ set up for L1 voltage call + bl voltage_shift @ go drop voltage + + /* dll lock mode */ + ldr r11, omap243x_sdi_sdrc_dlla_ctrl @ addr of dlla ctrl + ldr r10, [r11] @ get current val + cmp r12, #0x1 @ cs1 base (2422 es2.05/1) + addeq r11, r11, #0x8 @ if cs1 base, move to DLLB + mvn r9, #0x4 @ mask to get clear bit2 + and r10, r10, r9 @ clear bit2 for lock mode. + orr r10, r10, #0x8 @ make sure DLL on (es2 bit pos) + orr r10, r10, #0x2 @ 90 degree phase for all below 133Mhz + str r10, [r11] @ commit to DLLA_CTRL + bl i_dll_wait @ wait for dll to lock + + /* get dll value */ + add r11, r11, #0x4 @ get addr of status reg + ldr r10, [r11] @ get locked value + + /* voltage shift up */ + mov r9, #0x0 @ shift back to L0-voltage + bl voltage_shift @ go raise voltage + + /* frequency shift up */ + mov r3, #0x2 @ value for 2x operation + str r3, [r2] @ go to L0-freq operation + + /* reset entry mode for dllctrl */ + sub r11, r11, #0x4 @ move from status to ctrl + cmp r12, #0x1 @ normalize if cs1 based + subeq r11, r11, #0x8 @ possibly back to DLLA + cmp r8, #0x1 @ if forced unlock exit + orreq r1, r1, #0x4 @ make sure exit with unlocked value + str r1, [r11] @ restore DLLA_CTRL high value + add r11, r11, #0x8 @ move to DLLB_CTRL addr + str r1, [r11] @ set value DLLB_CTRL + bl i_dll_wait @ wait for possible lock + + /* set up for return, DDR should be good */ + str r10, [r0] @ write dll_status and return counter + ldmfd sp!, {r0 - r12, pc} @ restore regs and return + + /* ensure the DLL has relocked */ +i_dll_wait: + mov r4, #0x800 @ delay DLL relock, min 0x400 L3 clocks +i_dll_delay: + subs r4, r4, #0x1 + bne i_dll_delay + mov pc, lr + + /* + * shift up or down voltage, use R9 as input to tell level. + * wait for it to finish, use 32k sync counter, 1tick=31uS. + */ +voltage_shift: + ldr r4, omap243x_sdi_prcm_voltctrl @ get addr of volt ctrl. + ldr r5, [r4] @ get value. + ldr r6, prcm_mask_val @ get value of mask + and r5, r5, r6 @ apply mask to clear bits + orr r5, r5, r9 @ bulld value for L0/L1-volt operation. + str r5, [r4] @ set up for change. + mov r3, #0x4000 @ get val for force + orr r5, r5, r3 @ build value for force + str r5, [r4] @ Force transition to L1 + + ldr r3, omap243x_sdi_timer_32ksynct_cr @ get addr of counter + ldr r5, [r3] @ get value + add r5, r5, #0x3 @ give it at most 93uS +volt_delay: + ldr r7, [r3] @ get timer value + cmp r5, r7 @ time up? + bhi volt_delay @ not yet->branch + mov pc, lr @ back to caller. + +omap243x_sdi_cm_clksel2_pll: + .word OMAP2430_CM_REGADDR(PLL_MOD, CM_CLKSEL2) +omap243x_sdi_sdrc_dlla_ctrl: + .word OMAP243X_SDRC_REGADDR(SDRC_DLLA_CTRL) +omap243x_sdi_prcm_voltctrl: + .word OMAP243X_PRCM_VOLTCTRL +prcm_mask_val: + .word 0xFFFF3FFC +omap243x_sdi_timer_32ksynct_cr: + .word IO_ADDRESS(OMAP2_32KSYNCT_BASE + 0x010) +ENTRY(omap243x_sram_ddr_init_sz) + .word . - omap243x_sram_ddr_init + +/* + * Reprograms memory timings. + * r0 = [PRCM_FULL | PRCM_HALF] r1 = SDRC_DLLA_CTRL value r2 = [DDR | SDR] + * PRCM_FULL = 2, PRCM_HALF = 1, DDR = 1, SDR = 0 + */ +ENTRY(omap243x_sram_reprogram_sdrc) + stmfd sp!, {r0 - r10, lr} @ save registers on stack + mov r3, #0x0 @ clear for mrc call + mcr p15, 0, r3, c7, c10, 4 @ memory barrier, finish ARM SDR/DDR + nop + nop + ldr r6, omap243x_srs_sdrc_rfr_ctrl @ get addr of refresh reg + ldr r5, [r6] @ get value + mov r5, r5, lsr #8 @ isolate rfr field and drop burst + + cmp r0, #0x1 @ going to half speed? + movne r9, #0x0 @ if up set flag up for pre up, hi volt + + blne voltage_shift_c @ adjust voltage + + cmp r0, #0x1 @ going to half speed (post branch link) + moveq r5, r5, lsr #1 @ divide by 2 if to half + movne r5, r5, lsl #1 @ mult by 2 if to full + mov r5, r5, lsl #8 @ put rfr field back into place + add r5, r5, #0x1 @ turn on burst of 1 + ldr r4, omap243x_srs_cm_clksel2_pll @ get address of out reg + ldr r3, [r4] @ get curr value + orr r3, r3, #0x3 + bic r3, r3, #0x3 @ clear lower bits + orr r3, r3, r0 @ new state value + str r3, [r4] @ set new state (pll/x, x=1 or 2) + nop + nop + + moveq r9, #0x1 @ if speed down, post down, drop volt + bleq voltage_shift_c + + mcr p15, 0, r3, c7, c10, 4 @ memory barrier + str r5, [r6] @ set new RFR_1 value + add r6, r6, #0x30 @ get RFR_2 addr + str r5, [r6] @ set RFR_2 + nop + cmp r2, #0x1 @ (SDR or DDR) do we need to adjust DLL + bne freq_out @ leave if SDR, no DLL function + + /* With DDR, we need to take care of the DLL for the frequency change */ + ldr r2, omap243x_srs_sdrc_dlla_ctrl @ addr of dlla ctrl + str r1, [r2] @ write out new SDRC_DLLA_CTRL + add r2, r2, #0x8 @ addr to SDRC_DLLB_CTRL + str r1, [r2] @ commit to SDRC_DLLB_CTRL + mov r1, #0x2000 @ wait DLL relock, min 0x400 L3 clocks +dll_wait: + subs r1, r1, #0x1 + bne dll_wait +freq_out: + ldmfd sp!, {r0 - r10, pc} @ restore regs and return + + /* + * shift up or down voltage, use R9 as input to tell level. + * wait for it to finish, use 32k sync counter, 1tick=31uS. + */ +voltage_shift_c: + ldr r10, omap243x_srs_prcm_voltctrl @ get addr of volt ctrl + ldr r8, [r10] @ get value + ldr r7, ddr_prcm_mask_val @ get value of mask + and r8, r8, r7 @ apply mask to clear bits + orr r8, r8, r9 @ bulld value for L0/L1-volt operation. + str r8, [r10] @ set up for change. + mov r7, #0x4000 @ get val for force + orr r8, r8, r7 @ build value for force + str r8, [r10] @ Force transition to L1 + + ldr r10, omap243x_srs_timer_32ksynct @ get addr of counter + ldr r8, [r10] @ get value + add r8, r8, #0x2 @ give it at most 62uS (min 31+) +volt_delay_c: + ldr r7, [r10] @ get timer value + cmp r8, r7 @ time up? + bhi volt_delay_c @ not yet->branch + mov pc, lr @ back to caller + +omap243x_srs_cm_clksel2_pll: + .word OMAP2430_CM_REGADDR(PLL_MOD, CM_CLKSEL2) +omap243x_srs_sdrc_dlla_ctrl: + .word OMAP243X_SDRC_REGADDR(SDRC_DLLA_CTRL) +omap243x_srs_sdrc_rfr_ctrl: + .word OMAP243X_SDRC_REGADDR(SDRC_RFR_CTRL_0) +omap243x_srs_prcm_voltctrl: + .word OMAP243X_PRCM_VOLTCTRL +ddr_prcm_mask_val: + .word 0xFFFF3FFC +omap243x_srs_timer_32ksynct: + .word IO_ADDRESS(OMAP2_32KSYNCT_BASE + 0x010) + +ENTRY(omap243x_sram_reprogram_sdrc_sz) + .word . - omap243x_sram_reprogram_sdrc + +/* + * Set dividers and pll. Also recalculate DLL value for DDR and unlock mode. + */ +ENTRY(omap243x_sram_set_prcm) + stmfd sp!, {r0-r12, lr} @ regs to stack + adr r4, pbegin @ addr of preload start + adr r8, pend @ addr of preload end + mcrr p15, 1, r8, r4, c12 @ preload into icache +pbegin: + /* move into fast relock bypass */ + ldr r8, omap243x_ssp_pll_ctl @ get addr + ldr r5, [r8] @ get val + mvn r6, #0x3 @ clear mask + and r5, r5, r6 @ clear field + orr r7, r5, #0x2 @ fast relock val + str r7, [r8] @ go to fast relock + ldr r4, omap243x_ssp_pll_stat @ addr of stat +block: + /* wait for bypass */ + ldr r8, [r4] @ stat value + and r8, r8, #0x3 @ mask for stat + cmp r8, #0x1 @ there yet + bne block @ loop if not + + /* set new dpll dividers _after_ in bypass */ + ldr r4, omap243x_ssp_pll_div @ get addr + str r0, [r4] @ set dpll ctrl val + + ldr r4, omap243x_ssp_set_config @ get addr + mov r8, #1 @ valid cfg msk + str r8, [r4] @ make dividers take + + mov r4, #100 @ dead spin a bit +wait_a_bit: + subs r4, r4, #1 @ dec loop + bne wait_a_bit @ delay done? + + /* check if staying in bypass */ + cmp r2, #0x1 @ stay in bypass? + beq pend @ jump over dpll relock + + /* relock DPLL with new vals */ + ldr r5, omap243x_ssp_pll_stat @ get addr + ldr r4, omap243x_ssp_pll_ctl @ get addr + orr r8, r7, #0x3 @ val for lock dpll + str r8, [r4] @ set val + mov r0, #1000 @ dead spin a bit +wait_more: + subs r0, r0, #1 @ dec loop + bne wait_more @ delay done? +wait_lock: + ldr r8, [r5] @ get lock val + and r8, r8, #3 @ isolate field + cmp r8, #2 @ locked? + bne wait_lock @ wait if not +pend: + /* update memory timings & briefly lock dll */ + ldr r4, omap243x_ssp_sdrc_rfr @ get addr + str r1, [r4] @ update refresh timing + ldr r11, omap243x_ssp_dlla_ctrl @ get addr of DLLA ctrl + ldr r10, [r11] @ get current val + mvn r9, #0x4 @ mask to get clear bit2 + and r10, r10, r9 @ clear bit2 for lock mode + orr r10, r10, #0x8 @ make sure DLL on (es2 bit pos) + str r10, [r11] @ commit to DLLA_CTRL + add r11, r11, #0x8 @ move to dllb + str r10, [r11] @ hit DLLB also + + mov r4, #0x800 @ relock time (min 0x400 L3 clocks) +wait_dll_lock: + subs r4, r4, #0x1 + bne wait_dll_lock + nop + ldmfd sp!, {r0-r12, pc} @ restore regs and return + +omap243x_ssp_set_config: + .word OMAP243X_PRCM_CLKCFG_CTRL +omap243x_ssp_pll_ctl: + .word OMAP2430_CM_REGADDR(PLL_MOD, CM_CLKEN) +omap243x_ssp_pll_stat: + .word OMAP2430_CM_REGADDR(PLL_MOD, CM_IDLEST) +omap243x_ssp_pll_div: + .word OMAP2430_CM_REGADDR(PLL_MOD, CM_CLKSEL1) +omap243x_ssp_sdrc_rfr: + .word OMAP243X_SDRC_REGADDR(SDRC_RFR_CTRL_0) +omap243x_ssp_dlla_ctrl: + .word OMAP243X_SDRC_REGADDR(SDRC_DLLA_CTRL) + +ENTRY(omap243x_sram_set_prcm_sz) + .word . - omap243x_sram_set_prcm diff --git a/arch/arm/mach-omap2/timer-gp.c b/arch/arm/mach-omap2/timer-gp.c index 78d05f203ff..557603f9931 100644 --- a/arch/arm/mach-omap2/timer-gp.c +++ b/arch/arm/mach-omap2/timer-gp.c @@ -59,8 +59,7 @@ static struct irqaction omap2_gp_timer_irq = { static int omap2_gp_timer_set_next_event(unsigned long cycles, struct clock_event_device *evt) { - omap_dm_timer_set_load(gptimer, 0, 0xffffffff - cycles); - omap_dm_timer_start(gptimer); + omap_dm_timer_set_load_start(gptimer, 0, 0xffffffff - cycles); return 0; } @@ -77,8 +76,7 @@ static void omap2_gp_timer_set_mode(enum clock_event_mode mode, period = clk_get_rate(omap_dm_timer_get_fclk(gptimer)) / HZ; period -= 1; - omap_dm_timer_set_load(gptimer, 1, 0xffffffff - period); - omap_dm_timer_start(gptimer); + omap_dm_timer_set_load_start(gptimer, 1, 0xffffffff - period); break; case CLOCK_EVT_MODE_ONESHOT: break; @@ -172,8 +170,7 @@ static void __init omap2_gp_clocksource_init(void) tick_rate = clk_get_rate(omap_dm_timer_get_fclk(gpt)); tick_period = (tick_rate / HZ) - 1; - omap_dm_timer_set_load(gpt, 1, 0); - omap_dm_timer_start(gpt); + omap_dm_timer_set_load_start(gpt, 1, 0); clocksource_gpt.mult = clocksource_khz2mult(tick_rate/1000, clocksource_gpt.shift); diff --git a/arch/arm/mach-orion5x/Kconfig b/arch/arm/mach-orion5x/Kconfig index 93debf33615..ddcd41b15d1 100644 --- a/arch/arm/mach-orion5x/Kconfig +++ b/arch/arm/mach-orion5x/Kconfig @@ -44,6 +44,54 @@ config MACH_LINKSTATION_PRO Buffalo Linkstation Pro/Live platform. Both v1 and v2 devices are supported. +config MACH_TS409 + bool "QNAP TS-409" + help + Say 'Y' here if you want your kernel to support the + QNAP TS-409 platform. + +config MACH_WRT350N_V2 + bool "Linksys WRT350N v2" + help + Say 'Y' here if you want your kernel to support the + Linksys WRT350N v2 platform. + +config MACH_TS78XX + bool "Technologic Systems TS-78xx" + help + Say 'Y' here if you want your kernel to support the + Technologic Systems TS-78xx platform. + +config MACH_MV2120 + bool "HP Media Vault mv2120" + help + Say 'Y' here if you want your kernel to support the + HP Media Vault mv2120 or mv5100. + +config MACH_MSS2 + bool "Maxtor Shared Storage II" + help + Say 'Y' here if you want your kernel to support the + Maxtor Shared Storage II platform. + +config MACH_WNR854T + bool "Netgear WNR854T" + help + Say 'Y' here if you want your kernel to support the + Netgear WNR854T platform. + +config MACH_RD88F5181L_GE + bool "Marvell Orion-VoIP GE Reference Design" + help + Say 'Y' here if you want your kernel to support the + Marvell Orion-VoIP GE (88F5181L) RD. + +config MACH_RD88F5181L_FXO + bool "Marvell Orion-VoIP FXO Reference Design" + help + Say 'Y' here if you want your kernel to support the + Marvell Orion-VoIP FXO (88F5181L) RD. + endmenu endif diff --git a/arch/arm/mach-orion5x/Makefile b/arch/arm/mach-orion5x/Makefile index 9301bf55910..fcc48a8864f 100644 --- a/arch/arm/mach-orion5x/Makefile +++ b/arch/arm/mach-orion5x/Makefile @@ -1,7 +1,15 @@ -obj-y += common.o addr-map.o pci.o gpio.o irq.o +obj-y += common.o addr-map.o pci.o gpio.o irq.o mpp.o obj-$(CONFIG_MACH_DB88F5281) += db88f5281-setup.o obj-$(CONFIG_MACH_RD88F5182) += rd88f5182-setup.o obj-$(CONFIG_MACH_KUROBOX_PRO) += kurobox_pro-setup.o obj-$(CONFIG_MACH_LINKSTATION_PRO) += kurobox_pro-setup.o obj-$(CONFIG_MACH_DNS323) += dns323-setup.o -obj-$(CONFIG_MACH_TS209) += ts209-setup.o +obj-$(CONFIG_MACH_TS209) += ts209-setup.o tsx09-common.o +obj-$(CONFIG_MACH_TS409) += ts409-setup.o tsx09-common.o +obj-$(CONFIG_MACH_WRT350N_V2) += wrt350n-v2-setup.o +obj-$(CONFIG_MACH_TS78XX) += ts78xx-setup.o +obj-$(CONFIG_MACH_MV2120) += mv2120-setup.o +obj-$(CONFIG_MACH_MSS2) += mss2-setup.o +obj-$(CONFIG_MACH_WNR854T) += wnr854t-setup.o +obj-$(CONFIG_MACH_RD88F5181L_GE) += rd88f5181l-ge-setup.o +obj-$(CONFIG_MACH_RD88F5181L_FXO) += rd88f5181l-fxo-setup.o diff --git a/arch/arm/mach-orion5x/addr-map.c b/arch/arm/mach-orion5x/addr-map.c index e63fb05dc89..6f0dbda6c44 100644 --- a/arch/arm/mach-orion5x/addr-map.c +++ b/arch/arm/mach-orion5x/addr-map.c @@ -70,6 +70,7 @@ struct mbus_dram_target_info orion5x_mbus_dram_info; +static int __initdata win_alloc_count; static int __init orion5x_cpu_win_can_remap(int win) { @@ -87,16 +88,22 @@ static int __init orion5x_cpu_win_can_remap(int win) static void __init setup_cpu_win(int win, u32 base, u32 size, u8 target, u8 attr, int remap) { - orion5x_write(CPU_WIN_BASE(win), base & 0xffff0000); - orion5x_write(CPU_WIN_CTRL(win), - ((size - 1) & 0xffff0000) | (attr << 8) | (target << 4) | 1); + if (win >= 8) { + printk(KERN_ERR "setup_cpu_win: trying to allocate " + "window %d\n", win); + return; + } + + writel(base & 0xffff0000, CPU_WIN_BASE(win)); + writel(((size - 1) & 0xffff0000) | (attr << 8) | (target << 4) | 1, + CPU_WIN_CTRL(win)); if (orion5x_cpu_win_can_remap(win)) { if (remap < 0) remap = base; - orion5x_write(CPU_WIN_REMAP_LO(win), remap & 0xffff0000); - orion5x_write(CPU_WIN_REMAP_HI(win), 0); + writel(remap & 0xffff0000, CPU_WIN_REMAP_LO(win)); + writel(0, CPU_WIN_REMAP_HI(win)); } } @@ -109,11 +116,11 @@ void __init orion5x_setup_cpu_mbus_bridge(void) * First, disable and clear windows. */ for (i = 0; i < 8; i++) { - orion5x_write(CPU_WIN_BASE(i), 0); - orion5x_write(CPU_WIN_CTRL(i), 0); + writel(0, CPU_WIN_BASE(i)); + writel(0, CPU_WIN_CTRL(i)); if (orion5x_cpu_win_can_remap(i)) { - orion5x_write(CPU_WIN_REMAP_LO(i), 0); - orion5x_write(CPU_WIN_REMAP_HI(i), 0); + writel(0, CPU_WIN_REMAP_LO(i)); + writel(0, CPU_WIN_REMAP_HI(i)); } } @@ -128,6 +135,7 @@ void __init orion5x_setup_cpu_mbus_bridge(void) TARGET_PCIE, ATTR_PCIE_MEM, -1); setup_cpu_win(3, ORION5X_PCI_MEM_PHYS_BASE, ORION5X_PCI_MEM_SIZE, TARGET_PCI, ATTR_PCI_MEM, -1); + win_alloc_count = 4; /* * Setup MBUS dram target info. @@ -147,8 +155,8 @@ void __init orion5x_setup_cpu_mbus_bridge(void) w = &orion5x_mbus_dram_info.cs[cs++]; w->cs_index = i; w->mbus_attr = 0xf & ~(1 << i); - w->base = base & 0xff000000; - w->size = (size | 0x00ffffff) + 1; + w->base = base & 0xffff0000; + w->size = (size | 0x0000ffff) + 1; } } orion5x_mbus_dram_info.num_cs = cs; @@ -156,25 +164,30 @@ void __init orion5x_setup_cpu_mbus_bridge(void) void __init orion5x_setup_dev_boot_win(u32 base, u32 size) { - setup_cpu_win(4, base, size, TARGET_DEV_BUS, ATTR_DEV_BOOT, -1); + setup_cpu_win(win_alloc_count++, base, size, + TARGET_DEV_BUS, ATTR_DEV_BOOT, -1); } void __init orion5x_setup_dev0_win(u32 base, u32 size) { - setup_cpu_win(5, base, size, TARGET_DEV_BUS, ATTR_DEV_CS0, -1); + setup_cpu_win(win_alloc_count++, base, size, + TARGET_DEV_BUS, ATTR_DEV_CS0, -1); } void __init orion5x_setup_dev1_win(u32 base, u32 size) { - setup_cpu_win(6, base, size, TARGET_DEV_BUS, ATTR_DEV_CS1, -1); + setup_cpu_win(win_alloc_count++, base, size, + TARGET_DEV_BUS, ATTR_DEV_CS1, -1); } void __init orion5x_setup_dev2_win(u32 base, u32 size) { - setup_cpu_win(7, base, size, TARGET_DEV_BUS, ATTR_DEV_CS2, -1); + setup_cpu_win(win_alloc_count++, base, size, + TARGET_DEV_BUS, ATTR_DEV_CS2, -1); } void __init orion5x_setup_pcie_wa_win(u32 base, u32 size) { - setup_cpu_win(7, base, size, TARGET_PCIE, ATTR_PCIE_WA, -1); + setup_cpu_win(win_alloc_count++, base, size, + TARGET_PCIE, ATTR_PCIE_WA, -1); } diff --git a/arch/arm/mach-orion5x/common.c b/arch/arm/mach-orion5x/common.c index 4f13fd037f0..faf4e321191 100644 --- a/arch/arm/mach-orion5x/common.c +++ b/arch/arm/mach-orion5x/common.c @@ -39,25 +39,22 @@ static struct map_desc orion5x_io_desc[] __initdata = { .virtual = ORION5X_REGS_VIRT_BASE, .pfn = __phys_to_pfn(ORION5X_REGS_PHYS_BASE), .length = ORION5X_REGS_SIZE, - .type = MT_DEVICE - }, - { + .type = MT_DEVICE, + }, { .virtual = ORION5X_PCIE_IO_VIRT_BASE, .pfn = __phys_to_pfn(ORION5X_PCIE_IO_PHYS_BASE), .length = ORION5X_PCIE_IO_SIZE, - .type = MT_DEVICE - }, - { + .type = MT_DEVICE, + }, { .virtual = ORION5X_PCI_IO_VIRT_BASE, .pfn = __phys_to_pfn(ORION5X_PCI_IO_PHYS_BASE), .length = ORION5X_PCI_IO_SIZE, - .type = MT_DEVICE - }, - { + .type = MT_DEVICE, + }, { .virtual = ORION5X_PCIE_WA_VIRT_BASE, .pfn = __phys_to_pfn(ORION5X_PCIE_WA_PHYS_BASE), .length = ORION5X_PCIE_WA_SIZE, - .type = MT_DEVICE + .type = MT_DEVICE, }, }; @@ -66,101 +63,32 @@ void __init orion5x_map_io(void) iotable_init(orion5x_io_desc, ARRAY_SIZE(orion5x_io_desc)); } + /***************************************************************************** - * UART + * EHCI ****************************************************************************/ - -static struct resource orion5x_uart_resources[] = { - { - .start = UART0_PHYS_BASE, - .end = UART0_PHYS_BASE + 0xff, - .flags = IORESOURCE_MEM, - }, - { - .start = IRQ_ORION5X_UART0, - .end = IRQ_ORION5X_UART0, - .flags = IORESOURCE_IRQ, - }, - { - .start = UART1_PHYS_BASE, - .end = UART1_PHYS_BASE + 0xff, - .flags = IORESOURCE_MEM, - }, - { - .start = IRQ_ORION5X_UART1, - .end = IRQ_ORION5X_UART1, - .flags = IORESOURCE_IRQ, - }, -}; - -static struct plat_serial8250_port orion5x_uart_data[] = { - { - .mapbase = UART0_PHYS_BASE, - .membase = (char *)UART0_VIRT_BASE, - .irq = IRQ_ORION5X_UART0, - .flags = UPF_SKIP_TEST | UPF_BOOT_AUTOCONF, - .iotype = UPIO_MEM, - .regshift = 2, - .uartclk = ORION5X_TCLK, - }, - { - .mapbase = UART1_PHYS_BASE, - .membase = (char *)UART1_VIRT_BASE, - .irq = IRQ_ORION5X_UART1, - .flags = UPF_SKIP_TEST | UPF_BOOT_AUTOCONF, - .iotype = UPIO_MEM, - .regshift = 2, - .uartclk = ORION5X_TCLK, - }, - { }, +static struct orion_ehci_data orion5x_ehci_data = { + .dram = &orion5x_mbus_dram_info, }; -static struct platform_device orion5x_uart = { - .name = "serial8250", - .id = PLAT8250_DEV_PLATFORM, - .dev = { - .platform_data = orion5x_uart_data, - }, - .resource = orion5x_uart_resources, - .num_resources = ARRAY_SIZE(orion5x_uart_resources), -}; +static u64 ehci_dmamask = 0xffffffffUL; -/******************************************************************************* - * USB Controller - 2 interfaces - ******************************************************************************/ +/***************************************************************************** + * EHCI0 + ****************************************************************************/ static struct resource orion5x_ehci0_resources[] = { { .start = ORION5X_USB0_PHYS_BASE, .end = ORION5X_USB0_PHYS_BASE + SZ_4K - 1, .flags = IORESOURCE_MEM, - }, - { + }, { .start = IRQ_ORION5X_USB0_CTRL, .end = IRQ_ORION5X_USB0_CTRL, .flags = IORESOURCE_IRQ, }, }; -static struct resource orion5x_ehci1_resources[] = { - { - .start = ORION5X_USB1_PHYS_BASE, - .end = ORION5X_USB1_PHYS_BASE + SZ_4K - 1, - .flags = IORESOURCE_MEM, - }, - { - .start = IRQ_ORION5X_USB1_CTRL, - .end = IRQ_ORION5X_USB1_CTRL, - .flags = IORESOURCE_IRQ, - }, -}; - -static struct orion_ehci_data orion5x_ehci_data = { - .dram = &orion5x_mbus_dram_info, -}; - -static u64 ehci_dmamask = 0xffffffffUL; - static struct platform_device orion5x_ehci0 = { .name = "orion-ehci", .id = 0, @@ -173,6 +101,27 @@ static struct platform_device orion5x_ehci0 = { .num_resources = ARRAY_SIZE(orion5x_ehci0_resources), }; +void __init orion5x_ehci0_init(void) +{ + platform_device_register(&orion5x_ehci0); +} + + +/***************************************************************************** + * EHCI1 + ****************************************************************************/ +static struct resource orion5x_ehci1_resources[] = { + { + .start = ORION5X_USB1_PHYS_BASE, + .end = ORION5X_USB1_PHYS_BASE + SZ_4K - 1, + .flags = IORESOURCE_MEM, + }, { + .start = IRQ_ORION5X_USB1_CTRL, + .end = IRQ_ORION5X_USB1_CTRL, + .flags = IORESOURCE_IRQ, + }, +}; + static struct platform_device orion5x_ehci1 = { .name = "orion-ehci", .id = 1, @@ -185,11 +134,15 @@ static struct platform_device orion5x_ehci1 = { .num_resources = ARRAY_SIZE(orion5x_ehci1_resources), }; +void __init orion5x_ehci1_init(void) +{ + platform_device_register(&orion5x_ehci1); +} + + /***************************************************************************** - * Gigabit Ethernet port - * (The Orion and Discovery (MV643xx) families use the same Ethernet driver) + * GigE ****************************************************************************/ - struct mv643xx_eth_shared_platform_data orion5x_eth_shared_data = { .dram = &orion5x_mbus_dram_info, .t_clk = ORION5X_TCLK, @@ -219,7 +172,7 @@ static struct resource orion5x_eth_resources[] = { .start = IRQ_ORION5X_ETH_SUM, .end = IRQ_ORION5X_ETH_SUM, .flags = IORESOURCE_IRQ, - } + }, }; static struct platform_device orion5x_eth = { @@ -238,11 +191,10 @@ void __init orion5x_eth_init(struct mv643xx_eth_platform_data *eth_data) platform_device_register(&orion5x_eth); } + /***************************************************************************** - * I2C controller - * (The Orion and Discovery (MV643xx) families share the same I2C controller) + * I2C ****************************************************************************/ - static struct mv64xxx_i2c_pdata orion5x_i2c_pdata = { .freq_m = 8, /* assumes 166 MHz TCLK */ .freq_n = 3, @@ -251,16 +203,15 @@ static struct mv64xxx_i2c_pdata orion5x_i2c_pdata = { static struct resource orion5x_i2c_resources[] = { { - .name = "i2c base", - .start = I2C_PHYS_BASE, - .end = I2C_PHYS_BASE + 0x20 -1, - .flags = IORESOURCE_MEM, - }, - { - .name = "i2c irq", - .start = IRQ_ORION5X_I2C, - .end = IRQ_ORION5X_I2C, - .flags = IORESOURCE_IRQ, + .name = "i2c base", + .start = I2C_PHYS_BASE, + .end = I2C_PHYS_BASE + 0x1f, + .flags = IORESOURCE_MEM, + }, { + .name = "i2c irq", + .start = IRQ_ORION5X_I2C, + .end = IRQ_ORION5X_I2C, + .flags = IORESOURCE_IRQ, }, }; @@ -270,36 +221,41 @@ static struct platform_device orion5x_i2c = { .num_resources = ARRAY_SIZE(orion5x_i2c_resources), .resource = orion5x_i2c_resources, .dev = { - .platform_data = &orion5x_i2c_pdata, + .platform_data = &orion5x_i2c_pdata, }, }; +void __init orion5x_i2c_init(void) +{ + platform_device_register(&orion5x_i2c); +} + + /***************************************************************************** - * Sata port + * SATA ****************************************************************************/ static struct resource orion5x_sata_resources[] = { - { - .name = "sata base", - .start = ORION5X_SATA_PHYS_BASE, - .end = ORION5X_SATA_PHYS_BASE + 0x5000 - 1, - .flags = IORESOURCE_MEM, - }, { - .name = "sata irq", - .start = IRQ_ORION5X_SATA, - .end = IRQ_ORION5X_SATA, - .flags = IORESOURCE_IRQ, - }, + .name = "sata base", + .start = ORION5X_SATA_PHYS_BASE, + .end = ORION5X_SATA_PHYS_BASE + 0x5000 - 1, + .flags = IORESOURCE_MEM, + }, { + .name = "sata irq", + .start = IRQ_ORION5X_SATA, + .end = IRQ_ORION5X_SATA, + .flags = IORESOURCE_IRQ, + }, }; static struct platform_device orion5x_sata = { - .name = "sata_mv", - .id = 0, + .name = "sata_mv", + .id = 0, .dev = { .coherent_dma_mask = 0xffffffff, }, - .num_resources = ARRAY_SIZE(orion5x_sata_resources), - .resource = orion5x_sata_resources, + .num_resources = ARRAY_SIZE(orion5x_sata_resources), + .resource = orion5x_sata_resources, }; void __init orion5x_sata_init(struct mv_sata_platform_data *sata_data) @@ -309,23 +265,111 @@ void __init orion5x_sata_init(struct mv_sata_platform_data *sata_data) platform_device_register(&orion5x_sata); } + /***************************************************************************** - * Time handling + * UART0 + ****************************************************************************/ +static struct plat_serial8250_port orion5x_uart0_data[] = { + { + .mapbase = UART0_PHYS_BASE, + .membase = (char *)UART0_VIRT_BASE, + .irq = IRQ_ORION5X_UART0, + .flags = UPF_SKIP_TEST | UPF_BOOT_AUTOCONF, + .iotype = UPIO_MEM, + .regshift = 2, + .uartclk = ORION5X_TCLK, + }, { + }, +}; + +static struct resource orion5x_uart0_resources[] = { + { + .start = UART0_PHYS_BASE, + .end = UART0_PHYS_BASE + 0xff, + .flags = IORESOURCE_MEM, + }, { + .start = IRQ_ORION5X_UART0, + .end = IRQ_ORION5X_UART0, + .flags = IORESOURCE_IRQ, + }, +}; + +static struct platform_device orion5x_uart0 = { + .name = "serial8250", + .id = PLAT8250_DEV_PLATFORM, + .dev = { + .platform_data = orion5x_uart0_data, + }, + .resource = orion5x_uart0_resources, + .num_resources = ARRAY_SIZE(orion5x_uart0_resources), +}; + +void __init orion5x_uart0_init(void) +{ + platform_device_register(&orion5x_uart0); +} + + +/***************************************************************************** + * UART1 ****************************************************************************/ +static struct plat_serial8250_port orion5x_uart1_data[] = { + { + .mapbase = UART1_PHYS_BASE, + .membase = (char *)UART1_VIRT_BASE, + .irq = IRQ_ORION5X_UART1, + .flags = UPF_SKIP_TEST | UPF_BOOT_AUTOCONF, + .iotype = UPIO_MEM, + .regshift = 2, + .uartclk = ORION5X_TCLK, + }, { + }, +}; + +static struct resource orion5x_uart1_resources[] = { + { + .start = UART1_PHYS_BASE, + .end = UART1_PHYS_BASE + 0xff, + .flags = IORESOURCE_MEM, + }, { + .start = IRQ_ORION5X_UART1, + .end = IRQ_ORION5X_UART1, + .flags = IORESOURCE_IRQ, + }, +}; + +static struct platform_device orion5x_uart1 = { + .name = "serial8250", + .id = PLAT8250_DEV_PLATFORM1, + .dev = { + .platform_data = orion5x_uart1_data, + }, + .resource = orion5x_uart1_resources, + .num_resources = ARRAY_SIZE(orion5x_uart1_resources), +}; + +void __init orion5x_uart1_init(void) +{ + platform_device_register(&orion5x_uart1); +} + +/***************************************************************************** + * Time handling + ****************************************************************************/ static void orion5x_timer_init(void) { orion_time_init(IRQ_ORION5X_BRIDGE, ORION5X_TCLK); } struct sys_timer orion5x_timer = { - .init = orion5x_timer_init, + .init = orion5x_timer_init, }; + /***************************************************************************** * General ****************************************************************************/ - /* * Identify device ID and rev from PCIe configuration header space '0'. */ @@ -350,8 +394,10 @@ static void __init orion5x_id(u32 *dev, u32 *rev, char **dev_name) } else if (*dev == MV88F5181_DEV_ID) { if (*rev == MV88F5181_REV_B1) { *dev_name = "MV88F5181-Rev-B1"; + } else if (*rev == MV88F5181L_REV_A1) { + *dev_name = "MV88F5181L-Rev-A1"; } else { - *dev_name = "MV88F5181-Rev-Unsupported"; + *dev_name = "MV88F5181(L)-Rev-Unsupported"; } } else { *dev_name = "Device-Unknown"; @@ -370,15 +416,6 @@ void __init orion5x_init(void) * Setup Orion address map */ orion5x_setup_cpu_mbus_bridge(); - - /* - * Register devices. - */ - platform_device_register(&orion5x_uart); - platform_device_register(&orion5x_ehci0); - if (dev == MV88F5182_DEV_ID) - platform_device_register(&orion5x_ehci1); - platform_device_register(&orion5x_i2c); } /* diff --git a/arch/arm/mach-orion5x/common.h b/arch/arm/mach-orion5x/common.h index bd0f05de6e1..f72cf0e7754 100644 --- a/arch/arm/mach-orion5x/common.h +++ b/arch/arm/mach-orion5x/common.h @@ -1,10 +1,12 @@ #ifndef __ARCH_ORION5X_COMMON_H #define __ARCH_ORION5X_COMMON_H +struct mv643xx_eth_platform_data; +struct mv_sata_platform_data; + /* * Basic Orion init functions used early by machine-setup. */ - void orion5x_map_io(void); void orion5x_init_irq(void); void orion5x_init(void); @@ -23,15 +25,22 @@ void orion5x_setup_dev1_win(u32 base, u32 size); void orion5x_setup_dev2_win(u32 base, u32 size); void orion5x_setup_pcie_wa_win(u32 base, u32 size); +void orion5x_ehci0_init(void); +void orion5x_ehci1_init(void); +void orion5x_eth_init(struct mv643xx_eth_platform_data *eth_data); +void orion5x_i2c_init(void); +void orion5x_sata_init(struct mv_sata_platform_data *sata_data); +void orion5x_uart0_init(void); +void orion5x_uart1_init(void); + /* - * Shared code used internally by other Orion core functions. - * (/mach-orion/pci.c) + * PCIe/PCI functions. */ - -struct pci_sys_data; struct pci_bus; +struct pci_sys_data; void orion5x_pcie_id(u32 *dev, u32 *rev); +void orion5x_pci_set_cardbus_mode(void); int orion5x_pci_sys_setup(int nr, struct pci_sys_data *sys); struct pci_bus *orion5x_pci_sys_scan_bus(int nr, struct pci_sys_data *sys); int orion5x_pci_map_irq(struct pci_dev *dev, u8 slot, u8 pin); @@ -40,26 +49,9 @@ int orion5x_pci_map_irq(struct pci_dev *dev, u8 slot, u8 pin); * Valid GPIO pins according to MPP setup, used by machine-setup. * (/mach-orion/gpio.c). */ - -void orion5x_gpio_set_valid_pins(u32 pins); +void orion5x_gpio_set_valid(unsigned pin, int valid); void gpio_display(void); /* debug */ -/* - * Pull in Orion Ethernet platform_data, used by machine-setup - */ - -struct mv643xx_eth_platform_data; - -void orion5x_eth_init(struct mv643xx_eth_platform_data *eth_data); - -/* - * Orion Sata platform_data, used by machine-setup - */ - -struct mv_sata_platform_data; - -void orion5x_sata_init(struct mv_sata_platform_data *sata_data); - struct machine_desc; struct meminfo; struct tag; diff --git a/arch/arm/mach-orion5x/db88f5281-setup.c b/arch/arm/mach-orion5x/db88f5281-setup.c index 44c64342dac..88405e74e5e 100644 --- a/arch/arm/mach-orion5x/db88f5281-setup.c +++ b/arch/arm/mach-orion5x/db88f5281-setup.c @@ -27,6 +27,7 @@ #include <asm/arch/orion5x.h> #include <asm/plat-orion/orion_nand.h> #include "common.h" +#include "mpp.h" /***************************************************************************** * DB-88F5281 on board devices @@ -86,7 +87,7 @@ static struct platform_device db88f5281_boot_flash = { .name = "physmap-flash", .id = 0, .dev = { - .platform_data = &db88f5281_boot_flash_data, + .platform_data = &db88f5281_boot_flash_data, }, .num_resources = 1, .resource = &db88f5281_boot_flash_resource, @@ -110,7 +111,7 @@ static struct platform_device db88f5281_nor_flash = { .name = "physmap-flash", .id = 1, .dev = { - .platform_data = &db88f5281_nor_flash_data, + .platform_data = &db88f5281_nor_flash_data, }, .num_resources = 1, .resource = &db88f5281_nor_flash_resource, @@ -125,18 +126,15 @@ static struct mtd_partition db88f5281_nand_parts[] = { .name = "kernel", .offset = 0, .size = SZ_2M, - }, - { + }, { .name = "root", .offset = SZ_2M, .size = (SZ_16M - SZ_2M), - }, - { + }, { .name = "user", .offset = SZ_16M, .size = SZ_8M, - }, - { + }, { .name = "recovery", .offset = (SZ_16M + SZ_8M), .size = SZ_8M, @@ -288,7 +286,6 @@ subsys_initcall(db88f5281_pci_init); ****************************************************************************/ static struct mv643xx_eth_platform_data db88f5281_eth_data = { .phy_addr = 8, - .force_phy_addr = 1, }; /***************************************************************************** @@ -301,11 +298,28 @@ static struct i2c_board_info __initdata db88f5281_i2c_rtc = { /***************************************************************************** * General Setup ****************************************************************************/ - -static struct platform_device *db88f5281_devs[] __initdata = { - &db88f5281_boot_flash, - &db88f5281_nor_flash, - &db88f5281_nand_flash, +static struct orion5x_mpp_mode db88f5281_mpp_modes[] __initdata = { + { 0, MPP_GPIO }, /* USB Over Current */ + { 1, MPP_GPIO }, /* USB Vbat input */ + { 2, MPP_PCI_ARB }, /* PCI_REQn[2] */ + { 3, MPP_PCI_ARB }, /* PCI_GNTn[2] */ + { 4, MPP_PCI_ARB }, /* PCI_REQn[3] */ + { 5, MPP_PCI_ARB }, /* PCI_GNTn[3] */ + { 6, MPP_GPIO }, /* JP0, CON17.2 */ + { 7, MPP_GPIO }, /* JP1, CON17.1 */ + { 8, MPP_GPIO }, /* JP2, CON11.2 */ + { 9, MPP_GPIO }, /* JP3, CON11.3 */ + { 10, MPP_GPIO }, /* RTC int */ + { 11, MPP_GPIO }, /* Baud Rate Generator */ + { 12, MPP_GPIO }, /* PCI int 1 */ + { 13, MPP_GPIO }, /* PCI int 2 */ + { 14, MPP_NAND }, /* NAND_REn[2] */ + { 15, MPP_NAND }, /* NAND_WEn[2] */ + { 16, MPP_UART }, /* UART1_RX */ + { 17, MPP_UART }, /* UART1_TX */ + { 18, MPP_UART }, /* UART1_CTSn */ + { 19, MPP_UART }, /* UART1_RTSn */ + { -1 }, }; static void __init db88f5281_init(void) @@ -315,39 +329,31 @@ static void __init db88f5281_init(void) */ orion5x_init(); + orion5x_mpp_conf(db88f5281_mpp_modes); + writel(0, MPP_DEV_CTRL); /* DEV_D[31:16] */ + /* - * Setup the CPU address decode windows for our on-board devices + * Configure peripherals. */ + orion5x_ehci0_init(); + orion5x_eth_init(&db88f5281_eth_data); + orion5x_i2c_init(); + orion5x_uart0_init(); + orion5x_uart1_init(); + orion5x_setup_dev_boot_win(DB88F5281_NOR_BOOT_BASE, DB88F5281_NOR_BOOT_SIZE); + platform_device_register(&db88f5281_boot_flash); + orion5x_setup_dev0_win(DB88F5281_7SEG_BASE, DB88F5281_7SEG_SIZE); - orion5x_setup_dev1_win(DB88F5281_NOR_BASE, DB88F5281_NOR_SIZE); - orion5x_setup_dev2_win(DB88F5281_NAND_BASE, DB88F5281_NAND_SIZE); - /* - * Setup Multiplexing Pins: - * MPP0: GPIO (USB Over Current) MPP1: GPIO (USB Vbat input) - * MPP2: PCI_REQn[2] MPP3: PCI_GNTn[2] - * MPP4: PCI_REQn[3] MPP5: PCI_GNTn[3] - * MPP6: GPIO (JP0, CON17.2) MPP7: GPIO (JP1, CON17.1) - * MPP8: GPIO (JP2, CON11.2) MPP9: GPIO (JP3, CON11.3) - * MPP10: GPIO (RTC int) MPP11: GPIO (Baud Rate Generator) - * MPP12: GPIO (PCI int 1) MPP13: GPIO (PCI int 2) - * MPP14: NAND_REn[2] MPP15: NAND_WEn[2] - * MPP16: UART1_RX MPP17: UART1_TX - * MPP18: UART1_CTS MPP19: UART1_RTS - * MPP-DEV: DEV_D[16:31] - */ - orion5x_write(MPP_0_7_CTRL, 0x00222203); - orion5x_write(MPP_8_15_CTRL, 0x44000000); - orion5x_write(MPP_16_19_CTRL, 0); - orion5x_write(MPP_DEV_CTRL, 0); + orion5x_setup_dev1_win(DB88F5281_NOR_BASE, DB88F5281_NOR_SIZE); + platform_device_register(&db88f5281_nor_flash); - orion5x_gpio_set_valid_pins(0x00003fc3); + orion5x_setup_dev2_win(DB88F5281_NAND_BASE, DB88F5281_NAND_SIZE); + platform_device_register(&db88f5281_nand_flash); - platform_add_devices(db88f5281_devs, ARRAY_SIZE(db88f5281_devs)); i2c_register_board_info(0, &db88f5281_i2c_rtc, 1); - orion5x_eth_init(&db88f5281_eth_data); } MACHINE_START(DB88F5281, "Marvell Orion-2 Development Board") diff --git a/arch/arm/mach-orion5x/dns323-setup.c b/arch/arm/mach-orion5x/dns323-setup.c index 27ce967ab9e..3791ca6f001 100644 --- a/arch/arm/mach-orion5x/dns323-setup.c +++ b/arch/arm/mach-orion5x/dns323-setup.c @@ -27,6 +27,7 @@ #include <asm/mach/pci.h> #include <asm/arch/orion5x.h> #include "common.h" +#include "mpp.h" #define DNS323_GPIO_LED_RIGHT_AMBER 1 #define DNS323_GPIO_LED_LEFT_AMBER 2 @@ -52,8 +53,6 @@ static int __init dns323_pci_map_irq(struct pci_dev *dev, u8 slot, u8 pin) if (irq != -1) return irq; - pr_err("%s: requested mapping for unknown device\n", __func__); - return -1; } @@ -81,7 +80,6 @@ subsys_initcall(dns323_pci_init); static struct mv643xx_eth_platform_data dns323_eth_data = { .phy_addr = 8, - .force_phy_addr = 1, }; /**************************************************************************** @@ -119,7 +117,7 @@ static struct mtd_partition dns323_partitions[] = { .name = "u-boot", .size = 0x00030000, .offset = 0x007d0000, - } + }, }; static struct physmap_flash_data dns323_nor_flash_data = { @@ -137,7 +135,9 @@ static struct resource dns323_nor_flash_resource = { static struct platform_device dns323_nor_flash = { .name = "physmap-flash", .id = 0, - .dev = { .platform_data = &dns323_nor_flash_data, }, + .dev = { + .platform_data = &dns323_nor_flash_data, + }, .resource = &dns323_nor_flash_resource, .num_resources = 1, }; @@ -170,7 +170,9 @@ static struct gpio_led_platform_data dns323_led_data = { static struct platform_device dns323_gpio_leds = { .name = "leds-gpio", .id = -1, - .dev = { .platform_data = &dns323_led_data, }, + .dev = { + .platform_data = &dns323_led_data, + }, }; /**************************************************************************** @@ -183,35 +185,53 @@ static struct gpio_keys_button dns323_buttons[] = { .gpio = DNS323_GPIO_KEY_RESET, .desc = "Reset Button", .active_low = 1, - }, - { + }, { .code = KEY_POWER, .gpio = DNS323_GPIO_KEY_POWER, .desc = "Power Button", .active_low = 1, - } + }, }; static struct gpio_keys_platform_data dns323_button_data = { .buttons = dns323_buttons, - .nbuttons = ARRAY_SIZE(dns323_buttons), + .nbuttons = ARRAY_SIZE(dns323_buttons), }; static struct platform_device dns323_button_device = { .name = "gpio-keys", .id = -1, .num_resources = 0, - .dev = { .platform_data = &dns323_button_data, }, + .dev = { + .platform_data = &dns323_button_data, + }, }; /**************************************************************************** * General Setup */ - -static struct platform_device *dns323_plat_devices[] __initdata = { - &dns323_nor_flash, - &dns323_gpio_leds, - &dns323_button_device, +static struct orion5x_mpp_mode dns323_mpp_modes[] __initdata = { + { 0, MPP_PCIE_RST_OUTn }, + { 1, MPP_GPIO }, /* right amber LED (sata ch0) */ + { 2, MPP_GPIO }, /* left amber LED (sata ch1) */ + { 3, MPP_UNUSED }, + { 4, MPP_GPIO }, /* power button LED */ + { 5, MPP_GPIO }, /* power button LED */ + { 6, MPP_GPIO }, /* GMT G751-2f overtemp */ + { 7, MPP_GPIO }, /* M41T80 nIRQ/OUT/SQW */ + { 8, MPP_GPIO }, /* triggers power off */ + { 9, MPP_GPIO }, /* power button switch */ + { 10, MPP_GPIO }, /* reset button switch */ + { 11, MPP_UNUSED }, + { 12, MPP_UNUSED }, + { 13, MPP_UNUSED }, + { 14, MPP_UNUSED }, + { 15, MPP_UNUSED }, + { 16, MPP_UNUSED }, + { 17, MPP_UNUSED }, + { 18, MPP_UNUSED }, + { 19, MPP_UNUSED }, + { -1 }, }; /* @@ -225,17 +245,15 @@ static struct platform_device *dns323_plat_devices[] __initdata = { static struct i2c_board_info __initdata dns323_i2c_devices[] = { { I2C_BOARD_INFO("g760a", 0x3e), - }, #if 0 /* this entry requires the new-style driver model lm75 driver, * for the meantime "insmod lm75.ko force_lm75=0,0x48" is needed */ - { + }, { I2C_BOARD_INFO("g751", 0x48), - }, #endif - { + }, { I2C_BOARD_INFO("m41t80", 0x68), - } + }, }; /* DNS-323 specific power off method */ @@ -250,62 +268,35 @@ static void __init dns323_init(void) /* Setup basic Orion functions. Need to be called early. */ orion5x_init(); + orion5x_mpp_conf(dns323_mpp_modes); + writel(0, MPP_DEV_CTRL); /* DEV_D[31:16] */ + + /* + * Configure peripherals. + */ + orion5x_ehci0_init(); + orion5x_eth_init(&dns323_eth_data); + orion5x_i2c_init(); + orion5x_uart0_init(); + /* setup flash mapping * CS3 holds a 8 MB Spansion S29GL064M90TFIR4 */ orion5x_setup_dev_boot_win(DNS323_NOR_BOOT_BASE, DNS323_NOR_BOOT_SIZE); + platform_device_register(&dns323_nor_flash); - /* DNS-323 has a Marvell 88X7042 SATA controller attached via PCIe - * - * Open a special address decode windows for the PCIe WA. - */ - orion5x_setup_pcie_wa_win(ORION5X_PCIE_WA_PHYS_BASE, - ORION5X_PCIE_WA_SIZE); - - /* set MPP to 0 as D-Link's 2.6.12.6 kernel did */ - orion5x_write(MPP_0_7_CTRL, 0); - orion5x_write(MPP_8_15_CTRL, 0); - orion5x_write(MPP_16_19_CTRL, 0); - orion5x_write(MPP_DEV_CTRL, 0); - - /* Define used GPIO pins - - GPIO Map: - - | 0 | | PEX_RST_OUT (not controlled by GPIO) - | 1 | Out | right amber LED (= sata ch0 LED) (low-active) - | 2 | Out | left amber LED (= sata ch1 LED) (low-active) - | 3 | Out | //unknown// - | 4 | Out | power button LED (low-active, together with pin #5) - | 5 | Out | power button LED (low-active, together with pin #4) - | 6 | In | GMT G751-2f overtemp. shutdown signal (low-active) - | 7 | In | M41T80 nIRQ/OUT/SQW signal - | 8 | Out | triggers power off (high-active) - | 9 | In | power button switch (low-active) - | 10 | In | reset button switch (low-active) - | 11 | Out | //unknown// - | 12 | Out | //unknown// - | 13 | Out | //unknown// - | 14 | Out | //unknown// - | 15 | Out | //unknown// - */ - orion5x_gpio_set_valid_pins(0x07f6); - - /* register dns323 specific power-off method */ - if ((gpio_request(DNS323_GPIO_POWER_OFF, "POWEROFF") != 0) - || (gpio_direction_output(DNS323_GPIO_POWER_OFF, 0) != 0)) - pr_err("DNS323: failed to setup power-off GPIO\n"); - - pm_power_off = dns323_power_off; + platform_device_register(&dns323_gpio_leds); - /* register flash and other platform devices */ - platform_add_devices(dns323_plat_devices, - ARRAY_SIZE(dns323_plat_devices)); + platform_device_register(&dns323_button_device); i2c_register_board_info(0, dns323_i2c_devices, ARRAY_SIZE(dns323_i2c_devices)); - orion5x_eth_init(&dns323_eth_data); + /* register dns323 specific power-off method */ + if (gpio_request(DNS323_GPIO_POWER_OFF, "POWEROFF") != 0 || + gpio_direction_output(DNS323_GPIO_POWER_OFF, 0) != 0) + pr_err("DNS323: failed to setup power-off GPIO\n"); + pm_power_off = dns323_power_off; } /* Warning: D-Link uses a wrong mach-type (=526) in their bootloader */ diff --git a/arch/arm/mach-orion5x/gpio.c b/arch/arm/mach-orion5x/gpio.c index 8108c316c42..d09797990f4 100644 --- a/arch/arm/mach-orion5x/gpio.c +++ b/arch/arm/mach-orion5x/gpio.c @@ -24,9 +24,12 @@ static DEFINE_SPINLOCK(gpio_lock); static unsigned long gpio_valid[BITS_TO_LONGS(GPIO_MAX)]; static const char *gpio_label[GPIO_MAX]; /* non null for allocated GPIOs */ -void __init orion5x_gpio_set_valid_pins(u32 pins) +void __init orion5x_gpio_set_valid(unsigned pin, int valid) { - gpio_valid[0] = pins; + if (valid) + __set_bit(pin, gpio_valid); + else + __clear_bit(pin, gpio_valid); } /* @@ -93,10 +96,10 @@ int gpio_get_value(unsigned pin) { int val, mask = 1 << pin; - if (orion5x_read(GPIO_IO_CONF) & mask) - val = orion5x_read(GPIO_DATA_IN) ^ orion5x_read(GPIO_IN_POL); + if (readl(GPIO_IO_CONF) & mask) + val = readl(GPIO_DATA_IN) ^ readl(GPIO_IN_POL); else - val = orion5x_read(GPIO_OUT); + val = readl(GPIO_OUT); return val & mask; } @@ -188,39 +191,39 @@ void gpio_display(void) printk("GPIO, free\n"); } else { printk("GPIO, used by %s, ", gpio_label[i]); - if (orion5x_read(GPIO_IO_CONF) & (1 << i)) { + if (readl(GPIO_IO_CONF) & (1 << i)) { printk("input, active %s, level %s, edge %s\n", - ((orion5x_read(GPIO_IN_POL) >> i) & 1) ? "low" : "high", - ((orion5x_read(GPIO_LEVEL_MASK) >> i) & 1) ? "enabled" : "masked", - ((orion5x_read(GPIO_EDGE_MASK) >> i) & 1) ? "enabled" : "masked"); + ((readl(GPIO_IN_POL) >> i) & 1) ? "low" : "high", + ((readl(GPIO_LEVEL_MASK) >> i) & 1) ? "enabled" : "masked", + ((readl(GPIO_EDGE_MASK) >> i) & 1) ? "enabled" : "masked"); } else { - printk("output, val=%d\n", (orion5x_read(GPIO_OUT) >> i) & 1); + printk("output, val=%d\n", (readl(GPIO_OUT) >> i) & 1); } } } printk(KERN_DEBUG "MPP_0_7_CTRL (0x%08x) = 0x%08x\n", - MPP_0_7_CTRL, orion5x_read(MPP_0_7_CTRL)); + MPP_0_7_CTRL, readl(MPP_0_7_CTRL)); printk(KERN_DEBUG "MPP_8_15_CTRL (0x%08x) = 0x%08x\n", - MPP_8_15_CTRL, orion5x_read(MPP_8_15_CTRL)); + MPP_8_15_CTRL, readl(MPP_8_15_CTRL)); printk(KERN_DEBUG "MPP_16_19_CTRL (0x%08x) = 0x%08x\n", - MPP_16_19_CTRL, orion5x_read(MPP_16_19_CTRL)); + MPP_16_19_CTRL, readl(MPP_16_19_CTRL)); printk(KERN_DEBUG "MPP_DEV_CTRL (0x%08x) = 0x%08x\n", - MPP_DEV_CTRL, orion5x_read(MPP_DEV_CTRL)); + MPP_DEV_CTRL, readl(MPP_DEV_CTRL)); printk(KERN_DEBUG "GPIO_OUT (0x%08x) = 0x%08x\n", - GPIO_OUT, orion5x_read(GPIO_OUT)); + GPIO_OUT, readl(GPIO_OUT)); printk(KERN_DEBUG "GPIO_IO_CONF (0x%08x) = 0x%08x\n", - GPIO_IO_CONF, orion5x_read(GPIO_IO_CONF)); + GPIO_IO_CONF, readl(GPIO_IO_CONF)); printk(KERN_DEBUG "GPIO_BLINK_EN (0x%08x) = 0x%08x\n", - GPIO_BLINK_EN, orion5x_read(GPIO_BLINK_EN)); + GPIO_BLINK_EN, readl(GPIO_BLINK_EN)); printk(KERN_DEBUG "GPIO_IN_POL (0x%08x) = 0x%08x\n", - GPIO_IN_POL, orion5x_read(GPIO_IN_POL)); + GPIO_IN_POL, readl(GPIO_IN_POL)); printk(KERN_DEBUG "GPIO_DATA_IN (0x%08x) = 0x%08x\n", - GPIO_DATA_IN, orion5x_read(GPIO_DATA_IN)); + GPIO_DATA_IN, readl(GPIO_DATA_IN)); printk(KERN_DEBUG "GPIO_LEVEL_MASK (0x%08x) = 0x%08x\n", - GPIO_LEVEL_MASK, orion5x_read(GPIO_LEVEL_MASK)); + GPIO_LEVEL_MASK, readl(GPIO_LEVEL_MASK)); printk(KERN_DEBUG "GPIO_EDGE_CAUSE (0x%08x) = 0x%08x\n", - GPIO_EDGE_CAUSE, orion5x_read(GPIO_EDGE_CAUSE)); + GPIO_EDGE_CAUSE, readl(GPIO_EDGE_CAUSE)); printk(KERN_DEBUG "GPIO_EDGE_MASK (0x%08x) = 0x%08x\n", - GPIO_EDGE_MASK, orion5x_read(GPIO_EDGE_MASK)); + GPIO_EDGE_MASK, readl(GPIO_EDGE_MASK)); } diff --git a/arch/arm/mach-orion5x/irq.c b/arch/arm/mach-orion5x/irq.c index dd21f38c5d3..e2a0084ab4a 100644 --- a/arch/arm/mach-orion5x/irq.c +++ b/arch/arm/mach-orion5x/irq.c @@ -82,7 +82,7 @@ static int orion5x_gpio_set_irq_type(u32 irq, u32 type) int pin = irq_to_gpio(irq); struct irq_desc *desc; - if ((orion5x_read(GPIO_IO_CONF) & (1 << pin)) == 0) { + if ((readl(GPIO_IO_CONF) & (1 << pin)) == 0) { printk(KERN_ERR "orion5x_gpio_set_irq_type failed " "(irq %d, pin %d).\n", irq, pin); return -EINVAL; @@ -117,7 +117,7 @@ static int orion5x_gpio_set_irq_type(u32 irq, u32 type) /* * set initial polarity based on current input level */ - if ((orion5x_read(GPIO_IN_POL) ^ orion5x_read(GPIO_DATA_IN)) + if ((readl(GPIO_IN_POL) ^ readl(GPIO_DATA_IN)) & (1 << pin)) orion5x_setbits(GPIO_IN_POL, (1 << pin)); /* falling */ else @@ -149,8 +149,8 @@ static void orion5x_gpio_irq_handler(unsigned int irq, struct irq_desc *desc) BUG_ON(irq < IRQ_ORION5X_GPIO_0_7 || irq > IRQ_ORION5X_GPIO_24_31); offs = (irq - IRQ_ORION5X_GPIO_0_7) * 8; - cause = (orion5x_read(GPIO_DATA_IN) & orion5x_read(GPIO_LEVEL_MASK)) | - (orion5x_read(GPIO_EDGE_CAUSE) & orion5x_read(GPIO_EDGE_MASK)); + cause = (readl(GPIO_DATA_IN) & readl(GPIO_LEVEL_MASK)) | + (readl(GPIO_EDGE_CAUSE) & readl(GPIO_EDGE_MASK)); for (pin = offs; pin < offs + 8; pin++) { if (cause & (1 << pin)) { @@ -158,9 +158,9 @@ static void orion5x_gpio_irq_handler(unsigned int irq, struct irq_desc *desc) desc = irq_desc + irq; if ((desc->status & IRQ_TYPE_SENSE_MASK) == IRQT_BOTHEDGE) { /* Swap polarity (race with GPIO line) */ - u32 polarity = orion5x_read(GPIO_IN_POL); + u32 polarity = readl(GPIO_IN_POL); polarity ^= 1 << pin; - orion5x_write(GPIO_IN_POL, polarity); + writel(polarity, GPIO_IN_POL); } desc_handle_irq(irq, desc); } @@ -175,9 +175,9 @@ static void __init orion5x_init_gpio_irq(void) /* * Mask and clear GPIO IRQ interrupts */ - orion5x_write(GPIO_LEVEL_MASK, 0x0); - orion5x_write(GPIO_EDGE_MASK, 0x0); - orion5x_write(GPIO_EDGE_CAUSE, 0x0); + writel(0x0, GPIO_LEVEL_MASK); + writel(0x0, GPIO_EDGE_MASK); + writel(0x0, GPIO_EDGE_CAUSE); /* * Register chained level handlers for GPIO IRQs by default. diff --git a/arch/arm/mach-orion5x/kurobox_pro-setup.c b/arch/arm/mach-orion5x/kurobox_pro-setup.c index f5074b877b7..84feac4a1fe 100644 --- a/arch/arm/mach-orion5x/kurobox_pro-setup.c +++ b/arch/arm/mach-orion5x/kurobox_pro-setup.c @@ -13,10 +13,12 @@ #include <linux/platform_device.h> #include <linux/pci.h> #include <linux/irq.h> +#include <linux/delay.h> #include <linux/mtd/physmap.h> #include <linux/mtd/nand.h> #include <linux/mv643xx_eth.h> #include <linux/i2c.h> +#include <linux/serial_reg.h> #include <linux/ata_platform.h> #include <asm/mach-types.h> #include <asm/gpio.h> @@ -25,6 +27,7 @@ #include <asm/arch/orion5x.h> #include <asm/plat-orion/orion_nand.h> #include "common.h" +#include "mpp.h" /***************************************************************************** * KUROBOX-PRO Info @@ -53,13 +56,11 @@ static struct mtd_partition kurobox_pro_nand_parts[] = { .name = "uImage", .offset = 0, .size = SZ_4M, - }, - { + }, { .name = "rootfs", .offset = SZ_4M, .size = SZ_64M, - }, - { + }, { .name = "extra", .offset = SZ_4M + SZ_64M, .size = SZ_256M - (SZ_4M + SZ_64M), @@ -132,8 +133,6 @@ static int __init kurobox_pro_pci_map_irq(struct pci_dev *dev, u8 slot, u8 pin) /* * PCI isn't used on the Kuro */ - printk(KERN_ERR "kurobox_pro_pci_map_irq failed, unknown bus\n"); - return -1; } @@ -161,7 +160,6 @@ subsys_initcall(kurobox_pro_pci_init); static struct mv643xx_eth_platform_data kurobox_pro_eth_data = { .phy_addr = 8, - .force_phy_addr = 1, }; /***************************************************************************** @@ -175,12 +173,169 @@ static struct i2c_board_info __initdata kurobox_pro_i2c_rtc = { * SATA ****************************************************************************/ static struct mv_sata_platform_data kurobox_pro_sata_data = { - .n_ports = 2, + .n_ports = 2, }; /***************************************************************************** + * Kurobox Pro specific power off method via UART1-attached microcontroller + ****************************************************************************/ + +#define UART1_REG(x) (UART1_VIRT_BASE + ((UART_##x) << 2)) + +static int kurobox_pro_miconread(unsigned char *buf, int count) +{ + int i; + int timeout; + + for (i = 0; i < count; i++) { + timeout = 10; + + while (!(readl(UART1_REG(LSR)) & UART_LSR_DR)) { + if (--timeout == 0) + break; + udelay(1000); + } + + if (timeout == 0) + break; + buf[i] = readl(UART1_REG(RX)); + } + + /* return read bytes */ + return i; +} + +static int kurobox_pro_miconwrite(const unsigned char *buf, int count) +{ + int i = 0; + + while (count--) { + while (!(readl(UART1_REG(LSR)) & UART_LSR_THRE)) + barrier(); + writel(buf[i++], UART1_REG(TX)); + } + + return 0; +} + +static int kurobox_pro_miconsend(const unsigned char *data, int count) +{ + int i; + unsigned char checksum = 0; + unsigned char recv_buf[40]; + unsigned char send_buf[40]; + unsigned char correct_ack[3]; + int retry = 2; + + /* Generate checksum */ + for (i = 0; i < count; i++) + checksum -= data[i]; + + do { + /* Send data */ + kurobox_pro_miconwrite(data, count); + + /* send checksum */ + kurobox_pro_miconwrite(&checksum, 1); + + if (kurobox_pro_miconread(recv_buf, sizeof(recv_buf)) <= 3) { + printk(KERN_ERR ">%s: receive failed.\n", __func__); + + /* send preamble to clear the receive buffer */ + memset(&send_buf, 0xff, sizeof(send_buf)); + kurobox_pro_miconwrite(send_buf, sizeof(send_buf)); + + /* make dummy reads */ + mdelay(100); + kurobox_pro_miconread(recv_buf, sizeof(recv_buf)); + } else { + /* Generate expected ack */ + correct_ack[0] = 0x01; + correct_ack[1] = data[1]; + correct_ack[2] = 0x00; + + /* checksum Check */ + if ((recv_buf[0] + recv_buf[1] + recv_buf[2] + + recv_buf[3]) & 0xFF) { + printk(KERN_ERR ">%s: Checksum Error : " + "Received data[%02x, %02x, %02x, %02x]" + "\n", __func__, recv_buf[0], + recv_buf[1], recv_buf[2], recv_buf[3]); + } else { + /* Check Received Data */ + if (correct_ack[0] == recv_buf[0] && + correct_ack[1] == recv_buf[1] && + correct_ack[2] == recv_buf[2]) { + /* Interval for next command */ + mdelay(10); + + /* Receive ACK */ + return 0; + } + } + /* Received NAK or illegal Data */ + printk(KERN_ERR ">%s: Error : NAK or Illegal Data " + "Received\n", __func__); + } + } while (retry--); + + /* Interval for next command */ + mdelay(10); + + return -1; +} + +static void kurobox_pro_power_off(void) +{ + const unsigned char watchdogkill[] = {0x01, 0x35, 0x00}; + const unsigned char shutdownwait[] = {0x00, 0x0c}; + const unsigned char poweroff[] = {0x00, 0x06}; + /* 38400 baud divisor */ + const unsigned divisor = ((ORION5X_TCLK + (8 * 38400)) / (16 * 38400)); + + pr_info("%s: triggering power-off...\n", __func__); + + /* hijack uart1 and reset into sane state (38400,8n1,even parity) */ + writel(0x83, UART1_REG(LCR)); + writel(divisor & 0xff, UART1_REG(DLL)); + writel((divisor >> 8) & 0xff, UART1_REG(DLM)); + writel(0x1b, UART1_REG(LCR)); + writel(0x00, UART1_REG(IER)); + writel(0x07, UART1_REG(FCR)); + writel(0x00, UART1_REG(MCR)); + + /* Send the commands to shutdown the Kurobox Pro */ + kurobox_pro_miconsend(watchdogkill, sizeof(watchdogkill)) ; + kurobox_pro_miconsend(shutdownwait, sizeof(shutdownwait)) ; + kurobox_pro_miconsend(poweroff, sizeof(poweroff)); +} + +/***************************************************************************** * General Setup ****************************************************************************/ +static struct orion5x_mpp_mode kurobox_pro_mpp_modes[] __initdata = { + { 0, MPP_UNUSED }, + { 1, MPP_UNUSED }, + { 2, MPP_GPIO }, /* GPIO Micon */ + { 3, MPP_GPIO }, /* GPIO Rtc */ + { 4, MPP_UNUSED }, + { 5, MPP_UNUSED }, + { 6, MPP_NAND }, /* NAND Flash REn */ + { 7, MPP_NAND }, /* NAND Flash WEn */ + { 8, MPP_UNUSED }, + { 9, MPP_UNUSED }, + { 10, MPP_UNUSED }, + { 11, MPP_UNUSED }, + { 12, MPP_SATA_LED }, /* SATA 0 presence */ + { 13, MPP_SATA_LED }, /* SATA 1 presence */ + { 14, MPP_SATA_LED }, /* SATA 0 active */ + { 15, MPP_SATA_LED }, /* SATA 1 active */ + { 16, MPP_UART }, /* UART1 RXD */ + { 17, MPP_UART }, /* UART1 TXD */ + { 18, MPP_UART }, /* UART1 CTSn */ + { 19, MPP_UART }, /* UART1 RTSn */ + { -1 }, +}; static void __init kurobox_pro_init(void) { @@ -189,46 +344,33 @@ static void __init kurobox_pro_init(void) */ orion5x_init(); - /* - * Setup the CPU address decode windows for our devices - */ - orion5x_setup_dev_boot_win(KUROBOX_PRO_NOR_BOOT_BASE, - KUROBOX_PRO_NOR_BOOT_SIZE); - orion5x_setup_dev0_win(KUROBOX_PRO_NAND_BASE, KUROBOX_PRO_NAND_SIZE); + orion5x_mpp_conf(kurobox_pro_mpp_modes); /* - * Open a special address decode windows for the PCIe WA. + * Configure peripherals. */ - orion5x_setup_pcie_wa_win(ORION5X_PCIE_WA_PHYS_BASE, - ORION5X_PCIE_WA_SIZE); - - /* - * Setup Multiplexing Pins -- - * MPP[0-1] Not used - * MPP[2] GPIO Micon - * MPP[3] GPIO RTC - * MPP[4-5] Not used - * MPP[6] Nand Flash REn - * MPP[7] Nand Flash WEn - * MPP[8-11] Not used - * MPP[12] SATA 0 presence Indication - * MPP[13] SATA 1 presence Indication - * MPP[14] SATA 0 active Indication - * MPP[15] SATA 1 active indication - * MPP[16-19] Not used - */ - orion5x_write(MPP_0_7_CTRL, 0x44220003); - orion5x_write(MPP_8_15_CTRL, 0x55550000); - orion5x_write(MPP_16_19_CTRL, 0x0); - - orion5x_gpio_set_valid_pins(0x0000000c); + orion5x_ehci0_init(); + orion5x_ehci1_init(); + orion5x_eth_init(&kurobox_pro_eth_data); + orion5x_i2c_init(); + orion5x_sata_init(&kurobox_pro_sata_data); + orion5x_uart0_init(); + orion5x_uart1_init(); + orion5x_setup_dev_boot_win(KUROBOX_PRO_NOR_BOOT_BASE, + KUROBOX_PRO_NOR_BOOT_SIZE); platform_device_register(&kurobox_pro_nor_flash); - if (machine_is_kurobox_pro()) + + if (machine_is_kurobox_pro()) { + orion5x_setup_dev0_win(KUROBOX_PRO_NAND_BASE, + KUROBOX_PRO_NAND_SIZE); platform_device_register(&kurobox_pro_nand_flash); + } + i2c_register_board_info(0, &kurobox_pro_i2c_rtc, 1); - orion5x_eth_init(&kurobox_pro_eth_data); - orion5x_sata_init(&kurobox_pro_sata_data); + + /* register Kurobox Pro specific power-off method */ + pm_power_off = kurobox_pro_power_off; } #ifdef CONFIG_MACH_KUROBOX_PRO diff --git a/arch/arm/mach-orion5x/mpp.c b/arch/arm/mach-orion5x/mpp.c new file mode 100644 index 00000000000..a48cadb0159 --- /dev/null +++ b/arch/arm/mach-orion5x/mpp.c @@ -0,0 +1,163 @@ +/* + * arch/arm/mach-orion5x/mpp.c + * + * MPP functions for Marvell Orion 5x SoCs + * + * This file is licensed under the terms of the GNU General Public + * License version 2. This program is licensed "as is" without any + * warranty of any kind, whether express or implied. + */ + +#include <linux/kernel.h> +#include <linux/init.h> +#include <linux/mbus.h> +#include <asm/hardware.h> +#include <asm/io.h> +#include "common.h" +#include "mpp.h" + +static int is_5181l(void) +{ + u32 dev; + u32 rev; + + orion5x_pcie_id(&dev, &rev); + + return !!(dev == MV88F5181_DEV_ID && rev >= MV88F5181L_REV_A0); +} + +static int is_5182(void) +{ + u32 dev; + u32 rev; + + orion5x_pcie_id(&dev, &rev); + + return !!(dev == MV88F5182_DEV_ID); +} + +static int is_5281(void) +{ + u32 dev; + u32 rev; + + orion5x_pcie_id(&dev, &rev); + + return !!(dev == MV88F5281_DEV_ID); +} + +static int __init determine_type_encoding(int mpp, enum orion5x_mpp_type type) +{ + switch (type) { + case MPP_UNUSED: + case MPP_GPIO: + if (mpp == 0) + return 3; + if (mpp >= 1 && mpp <= 15) + return 0; + if (mpp >= 16 && mpp <= 19) { + if (is_5182()) + return 5; + if (type == MPP_UNUSED) + return 0; + } + return -1; + + case MPP_PCIE_RST_OUTn: + if (mpp == 0) + return 0; + return -1; + + case MPP_PCI_ARB: + if (mpp >= 0 && mpp <= 7) + return 2; + return -1; + + case MPP_PCI_PMEn: + if (mpp == 2) + return 3; + return -1; + + case MPP_GIGE: + if (mpp >= 8 && mpp <= 19) + return 1; + return -1; + + case MPP_NAND: + if (is_5182() || is_5281()) { + if (mpp >= 4 && mpp <= 7) + return 4; + if (mpp >= 12 && mpp <= 17) + return 4; + } + return -1; + + case MPP_PCI_CLK: + if (is_5181l() && mpp >= 6 && mpp <= 7) + return 5; + return -1; + + case MPP_SATA_LED: + if (is_5182()) { + if (mpp >= 4 && mpp <= 7) + return 5; + if (mpp >= 12 && mpp <= 15) + return 5; + } + return -1; + + case MPP_UART: + if (mpp >= 16 && mpp <= 19) + return 0; + return -1; + } + + printk(KERN_INFO "unknown MPP type %d\n", type); + + return -1; +} + +void __init orion5x_mpp_conf(struct orion5x_mpp_mode *mode) +{ + u32 mpp_0_7_ctrl = readl(MPP_0_7_CTRL); + u32 mpp_8_15_ctrl = readl(MPP_8_15_CTRL); + u32 mpp_16_19_ctrl = readl(MPP_16_19_CTRL); + + while (mode->mpp >= 0) { + u32 *reg; + int num_type; + int shift; + + if (mode->mpp >= 0 && mode->mpp <= 7) + reg = &mpp_0_7_ctrl; + else if (mode->mpp >= 8 && mode->mpp <= 15) + reg = &mpp_8_15_ctrl; + else if (mode->mpp >= 16 && mode->mpp <= 19) + reg = &mpp_16_19_ctrl; + else { + printk(KERN_ERR "orion5x_mpp_conf: invalid MPP " + "(%d)\n", mode->mpp); + continue; + } + + num_type = determine_type_encoding(mode->mpp, mode->type); + if (num_type < 0) { + printk(KERN_ERR "orion5x_mpp_conf: invalid MPP " + "combination (%d, %d)\n", mode->mpp, + mode->type); + continue; + } + + shift = (mode->mpp & 7) << 2; + *reg &= ~(0xf << shift); + *reg |= (num_type & 0xf) << shift; + + orion5x_gpio_set_valid(mode->mpp, !!(mode->type == MPP_GPIO)); + + mode++; + } + + writel(mpp_0_7_ctrl, MPP_0_7_CTRL); + writel(mpp_8_15_ctrl, MPP_8_15_CTRL); + writel(mpp_16_19_ctrl, MPP_16_19_CTRL); +} diff --git a/arch/arm/mach-orion5x/mpp.h b/arch/arm/mach-orion5x/mpp.h new file mode 100644 index 00000000000..290e610dc01 --- /dev/null +++ b/arch/arm/mach-orion5x/mpp.h @@ -0,0 +1,74 @@ +#ifndef __ARCH_ORION5X_MPP_H +#define __ARCH_ORION5X_MPP_H + +enum orion5x_mpp_type { + /* + * This MPP is unused. + */ + MPP_UNUSED, + + /* + * This MPP pin is used as a generic GPIO pin. Valid for + * MPPs 0-15 and device bus data pins 16-31. On 5182, also + * valid for MPPs 16-19. + */ + MPP_GPIO, + + /* + * This MPP is used as PCIe_RST_OUTn pin. Valid for + * MPP 0 only. + */ + MPP_PCIE_RST_OUTn, + + /* + * This MPP is used as PCI arbiter pin (REQn/GNTn). + * Valid for MPPs 0-7 only. + */ + MPP_PCI_ARB, + + /* + * This MPP is used as PCI_PMEn pin. Valid for MPP 2 only. + */ + MPP_PCI_PMEn, + + /* + * This MPP is used as GigE half-duplex (COL, CRS) or GMII + * (RXERR, CRS, TXERR, TXD[7:4], RXD[7:4]) pin. Valid for + * MPPs 8-19 only. + */ + MPP_GIGE, + + /* + * This MPP is used as NAND REn/WEn pin. Valid for MPPs + * 4-7 and 12-17 only, and only on the 5181l/5182/5281. + */ + MPP_NAND, + + /* + * This MPP is used as a PCI clock output pin. Valid for + * MPPs 6-7 only, and only on the 5181l. + */ + MPP_PCI_CLK, + + /* + * This MPP is used as a SATA presence/activity LED. + * Valid for MPPs 4-7 and 12-15 only, and only on the 5182. + */ + MPP_SATA_LED, + + /* + * This MPP is used as UART1 RXD/TXD/CTSn/RTSn pin. + * Valid for MPPs 16-19 only. + */ + MPP_UART, +}; + +struct orion5x_mpp_mode { + int mpp; + enum orion5x_mpp_type type; +}; + +void orion5x_mpp_conf(struct orion5x_mpp_mode *mode); + + +#endif diff --git a/arch/arm/mach-orion5x/mss2-setup.c b/arch/arm/mach-orion5x/mss2-setup.c new file mode 100644 index 00000000000..7ce9e407d9d --- /dev/null +++ b/arch/arm/mach-orion5x/mss2-setup.c @@ -0,0 +1,270 @@ +/* + * Maxtor Shared Storage II Board Setup + * + * Maintainer: Sylver Bruneau <sylver.bruneau@googlemail.com> + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License + * as published by the Free Software Foundation; either version + * 2 of the License, or (at your option) any later version. + */ + +#include <linux/kernel.h> +#include <linux/init.h> +#include <linux/platform_device.h> +#include <linux/pci.h> +#include <linux/irq.h> +#include <linux/mtd/physmap.h> +#include <linux/mv643xx_eth.h> +#include <linux/leds.h> +#include <linux/gpio_keys.h> +#include <linux/input.h> +#include <linux/i2c.h> +#include <linux/ata_platform.h> +#include <linux/gpio.h> +#include <asm/mach-types.h> +#include <asm/mach/arch.h> +#include <asm/mach/pci.h> +#include <asm/arch/orion5x.h> +#include "common.h" +#include "mpp.h" + +#define MSS2_NOR_BOOT_BASE 0xff800000 +#define MSS2_NOR_BOOT_SIZE SZ_256K + +/***************************************************************************** + * Maxtor Shared Storage II Info + ****************************************************************************/ + +/* + * Maxtor Shared Storage II hardware : + * - Marvell 88F5182-A2 C500 + * - Marvell 88E1111 Gigabit Ethernet PHY + * - RTC M41T81 (@0x68) on I2C bus + * - 256KB NOR flash + * - 64MB of RAM + */ + +/***************************************************************************** + * 256KB NOR Flash on BOOT Device + ****************************************************************************/ + +static struct physmap_flash_data mss2_nor_flash_data = { + .width = 1, +}; + +static struct resource mss2_nor_flash_resource = { + .flags = IORESOURCE_MEM, + .start = MSS2_NOR_BOOT_BASE, + .end = MSS2_NOR_BOOT_BASE + MSS2_NOR_BOOT_SIZE - 1, +}; + +static struct platform_device mss2_nor_flash = { + .name = "physmap-flash", + .id = 0, + .dev = { + .platform_data = &mss2_nor_flash_data, + }, + .resource = &mss2_nor_flash_resource, + .num_resources = 1, +}; + +/**************************************************************************** + * PCI setup + ****************************************************************************/ +static int __init mss2_pci_map_irq(struct pci_dev *dev, u8 slot, u8 pin) +{ + int irq; + + /* + * Check for devices with hard-wired IRQs. + */ + irq = orion5x_pci_map_irq(dev, slot, pin); + if (irq != -1) + return irq; + + return -1; +} + +static struct hw_pci mss2_pci __initdata = { + .nr_controllers = 2, + .swizzle = pci_std_swizzle, + .setup = orion5x_pci_sys_setup, + .scan = orion5x_pci_sys_scan_bus, + .map_irq = mss2_pci_map_irq, +}; + +static int __init mss2_pci_init(void) +{ + if (machine_is_mss2()) + pci_common_init(&mss2_pci); + + return 0; +} +subsys_initcall(mss2_pci_init); + + +/***************************************************************************** + * Ethernet + ****************************************************************************/ + +static struct mv643xx_eth_platform_data mss2_eth_data = { + .phy_addr = 8, +}; + +/***************************************************************************** + * SATA + ****************************************************************************/ + +static struct mv_sata_platform_data mss2_sata_data = { + .n_ports = 2, +}; + +/***************************************************************************** + * GPIO buttons + ****************************************************************************/ + +#define MSS2_GPIO_KEY_RESET 12 +#define MSS2_GPIO_KEY_POWER 11 + +static struct gpio_keys_button mss2_buttons[] = { + { + .code = KEY_POWER, + .gpio = MSS2_GPIO_KEY_POWER, + .desc = "Power", + .active_low = 1, + }, { + .code = KEY_RESTART, + .gpio = MSS2_GPIO_KEY_RESET, + .desc = "Reset", + .active_low = 1, + }, +}; + +static struct gpio_keys_platform_data mss2_button_data = { + .buttons = mss2_buttons, + .nbuttons = ARRAY_SIZE(mss2_buttons), +}; + +static struct platform_device mss2_button_device = { + .name = "gpio-keys", + .id = -1, + .dev = { + .platform_data = &mss2_button_data, + }, +}; + +/***************************************************************************** + * RTC m41t81 on I2C bus + ****************************************************************************/ + +#define MSS2_GPIO_RTC_IRQ 3 + +static struct i2c_board_info __initdata mss2_i2c_rtc = { + I2C_BOARD_INFO("m41t81", 0x68), +}; + +/***************************************************************************** + * MSS2 power off method + ****************************************************************************/ +/* + * On the Maxtor Shared Storage II, the shutdown process is the following : + * - Userland modifies U-boot env to tell U-boot to go idle at next boot + * - The board reboots + * - U-boot starts and go into an idle mode until the user press "power" + */ +static void mss2_power_off(void) +{ + u32 reg; + + /* + * Enable and issue soft reset + */ + reg = readl(CPU_RESET_MASK); + reg |= 1 << 2; + writel(reg, CPU_RESET_MASK); + + reg = readl(CPU_SOFT_RESET); + reg |= 1; + writel(reg, CPU_SOFT_RESET); +} + +/**************************************************************************** + * General Setup + ****************************************************************************/ +static struct orion5x_mpp_mode mss2_mpp_modes[] __initdata = { + { 0, MPP_GPIO }, /* Power LED */ + { 1, MPP_GPIO }, /* Error LED */ + { 2, MPP_UNUSED }, + { 3, MPP_GPIO }, /* RTC interrupt */ + { 4, MPP_GPIO }, /* HDD ind. (Single/Dual)*/ + { 5, MPP_GPIO }, /* HD0 5V control */ + { 6, MPP_GPIO }, /* HD0 12V control */ + { 7, MPP_GPIO }, /* HD1 5V control */ + { 8, MPP_GPIO }, /* HD1 12V control */ + { 9, MPP_UNUSED }, + { 10, MPP_GPIO }, /* Fan control */ + { 11, MPP_GPIO }, /* Power button */ + { 12, MPP_GPIO }, /* Reset button */ + { 13, MPP_UNUSED }, + { 14, MPP_SATA_LED }, /* SATA 0 active */ + { 15, MPP_SATA_LED }, /* SATA 1 active */ + { 16, MPP_UNUSED }, + { 17, MPP_UNUSED }, + { 18, MPP_UNUSED }, + { 19, MPP_UNUSED }, + { -1 }, +}; + +static void __init mss2_init(void) +{ + /* Setup basic Orion functions. Need to be called early. */ + orion5x_init(); + + orion5x_mpp_conf(mss2_mpp_modes); + + /* + * MPP[20] Unused + * MPP[21] PCI clock + * MPP[22] USB 0 over current + * MPP[23] USB 1 over current + */ + + /* + * Configure peripherals. + */ + orion5x_ehci0_init(); + orion5x_ehci1_init(); + orion5x_eth_init(&mss2_eth_data); + orion5x_i2c_init(); + orion5x_sata_init(&mss2_sata_data); + orion5x_uart0_init(); + + orion5x_setup_dev_boot_win(MSS2_NOR_BOOT_BASE, MSS2_NOR_BOOT_SIZE); + platform_device_register(&mss2_nor_flash); + + platform_device_register(&mss2_button_device); + + if (gpio_request(MSS2_GPIO_RTC_IRQ, "rtc") == 0) { + if (gpio_direction_input(MSS2_GPIO_RTC_IRQ) == 0) + mss2_i2c_rtc.irq = gpio_to_irq(MSS2_GPIO_RTC_IRQ); + else + gpio_free(MSS2_GPIO_RTC_IRQ); + } + i2c_register_board_info(0, &mss2_i2c_rtc, 1); + + /* register mss2 specific power-off method */ + pm_power_off = mss2_power_off; +} + +MACHINE_START(MSS2, "Maxtor Shared Storage II") + /* Maintainer: Sylver Bruneau <sylver.bruneau@googlemail.com> */ + .phys_io = ORION5X_REGS_PHYS_BASE, + .io_pg_offst = ((ORION5X_REGS_VIRT_BASE) >> 18) & 0xFFFC, + .boot_params = 0x00000100, + .init_machine = mss2_init, + .map_io = orion5x_map_io, + .init_irq = orion5x_init_irq, + .timer = &orion5x_timer, + .fixup = tag_fixup_mem32 +MACHINE_END diff --git a/arch/arm/mach-orion5x/mv2120-setup.c b/arch/arm/mach-orion5x/mv2120-setup.c new file mode 100644 index 00000000000..55f3b0fdef8 --- /dev/null +++ b/arch/arm/mach-orion5x/mv2120-setup.c @@ -0,0 +1,239 @@ +/* + * Copyright (C) 2007 Herbert Valerio Riedel <hvr@gnu.org> + * Copyright (C) 2008 Martin Michlmayr <tbm@cyrius.com> + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU Lesser General Public License as + * published by the Free Software Foundation; either version 2 of the + * License, or (at your option) any later version. + */ + +#include <linux/kernel.h> +#include <linux/init.h> +#include <linux/platform_device.h> +#include <linux/irq.h> +#include <linux/mtd/physmap.h> +#include <linux/mv643xx_eth.h> +#include <linux/leds.h> +#include <linux/gpio_keys.h> +#include <linux/input.h> +#include <linux/i2c.h> +#include <linux/ata_platform.h> +#include <asm/mach-types.h> +#include <asm/gpio.h> +#include <asm/mach/arch.h> +#include <asm/arch/orion5x.h> +#include "common.h" +#include "mpp.h" + +#define MV2120_NOR_BOOT_BASE 0xf4000000 +#define MV2120_NOR_BOOT_SIZE SZ_512K + +#define MV2120_GPIO_RTC_IRQ 3 +#define MV2120_GPIO_KEY_RESET 17 +#define MV2120_GPIO_KEY_POWER 18 +#define MV2120_GPIO_POWER_OFF 19 + + +/***************************************************************************** + * Ethernet + ****************************************************************************/ +static struct mv643xx_eth_platform_data mv2120_eth_data = { + .phy_addr = 8, +}; + +static struct mv_sata_platform_data mv2120_sata_data = { + .n_ports = 2, +}; + +static struct mtd_partition mv2120_partitions[] = { + { + .name = "firmware", + .size = 0x00080000, + .offset = 0, + }, +}; + +static struct physmap_flash_data mv2120_nor_flash_data = { + .width = 1, + .parts = mv2120_partitions, + .nr_parts = ARRAY_SIZE(mv2120_partitions) +}; + +static struct resource mv2120_nor_flash_resource = { + .flags = IORESOURCE_MEM, + .start = MV2120_NOR_BOOT_BASE, + .end = MV2120_NOR_BOOT_BASE + MV2120_NOR_BOOT_SIZE - 1, +}; + +static struct platform_device mv2120_nor_flash = { + .name = "physmap-flash", + .id = 0, + .dev = { + .platform_data = &mv2120_nor_flash_data, + }, + .resource = &mv2120_nor_flash_resource, + .num_resources = 1, +}; + +static struct gpio_keys_button mv2120_buttons[] = { + { + .code = KEY_RESTART, + .gpio = MV2120_GPIO_KEY_RESET, + .desc = "reset", + .active_low = 1, + }, { + .code = KEY_POWER, + .gpio = MV2120_GPIO_KEY_POWER, + .desc = "power", + .active_low = 1, + }, +}; + +static struct gpio_keys_platform_data mv2120_button_data = { + .buttons = mv2120_buttons, + .nbuttons = ARRAY_SIZE(mv2120_buttons), +}; + +static struct platform_device mv2120_button_device = { + .name = "gpio-keys", + .id = -1, + .num_resources = 0, + .dev = { + .platform_data = &mv2120_button_data, + }, +}; + + +/**************************************************************************** + * General Setup + ****************************************************************************/ +static struct orion5x_mpp_mode mv2120_mpp_modes[] __initdata = { + { 0, MPP_GPIO }, /* Sys status LED */ + { 1, MPP_GPIO }, /* Sys error LED */ + { 2, MPP_GPIO }, /* OverTemp interrupt */ + { 3, MPP_GPIO }, /* RTC interrupt */ + { 4, MPP_GPIO }, /* V_LED 5V */ + { 5, MPP_GPIO }, /* V_LED 3.3V */ + { 6, MPP_UNUSED }, + { 7, MPP_UNUSED }, + { 8, MPP_GPIO }, /* SATA 0 fail LED */ + { 9, MPP_GPIO }, /* SATA 1 fail LED */ + { 10, MPP_UNUSED }, + { 11, MPP_UNUSED }, + { 12, MPP_SATA_LED }, /* SATA 0 presence */ + { 13, MPP_SATA_LED }, /* SATA 1 presence */ + { 14, MPP_SATA_LED }, /* SATA 0 active */ + { 15, MPP_SATA_LED }, /* SATA 1 active */ + { 16, MPP_UNUSED }, + { 17, MPP_GPIO }, /* Reset button */ + { 18, MPP_GPIO }, /* Power button */ + { 19, MPP_GPIO }, /* Power off */ + { -1 }, +}; + +static struct i2c_board_info __initdata mv2120_i2c_rtc = { + I2C_BOARD_INFO("pcf8563", 0x51), + .irq = 0, +}; + +static struct gpio_led mv2120_led_pins[] = { + { + .name = "mv2120:blue:health", + .gpio = 0, + }, + { + .name = "mv2120:red:health", + .gpio = 1, + }, + { + .name = "mv2120:led:bright", + .gpio = 4, + .default_trigger = "default-on", + }, + { + .name = "mv2120:led:dimmed", + .gpio = 5, + }, + { + .name = "mv2120:red:sata0", + .gpio = 8, + .active_low = 1, + }, + { + .name = "mv2120:red:sata1", + .gpio = 9, + .active_low = 1, + }, + +}; + +static struct gpio_led_platform_data mv2120_led_data = { + .leds = mv2120_led_pins, + .num_leds = ARRAY_SIZE(mv2120_led_pins), +}; + +static struct platform_device mv2120_leds = { + .name = "leds-gpio", + .id = -1, + .dev = { + .platform_data = &mv2120_led_data, + } +}; + +static void mv2120_power_off(void) +{ + pr_info("%s: triggering power-off...\n", __func__); + gpio_set_value(MV2120_GPIO_POWER_OFF, 0); +} + +static void __init mv2120_init(void) +{ + /* Setup basic Orion functions. Need to be called early. */ + orion5x_init(); + + orion5x_mpp_conf(mv2120_mpp_modes); + + /* + * Configure peripherals. + */ + orion5x_ehci0_init(); + orion5x_ehci1_init(); + orion5x_eth_init(&mv2120_eth_data); + orion5x_i2c_init(); + orion5x_sata_init(&mv2120_sata_data); + orion5x_uart0_init(); + + orion5x_setup_dev_boot_win(MV2120_NOR_BOOT_BASE, MV2120_NOR_BOOT_SIZE); + platform_device_register(&mv2120_nor_flash); + + platform_device_register(&mv2120_button_device); + + if (gpio_request(MV2120_GPIO_RTC_IRQ, "rtc") == 0) { + if (gpio_direction_input(MV2120_GPIO_RTC_IRQ) == 0) + mv2120_i2c_rtc.irq = gpio_to_irq(MV2120_GPIO_RTC_IRQ); + else + gpio_free(MV2120_GPIO_RTC_IRQ); + } + i2c_register_board_info(0, &mv2120_i2c_rtc, 1); + platform_device_register(&mv2120_leds); + + /* register mv2120 specific power-off method */ + if (gpio_request(MV2120_GPIO_POWER_OFF, "POWEROFF") != 0 || + gpio_direction_output(MV2120_GPIO_POWER_OFF, 1) != 0) + pr_err("mv2120: failed to setup power-off GPIO\n"); + pm_power_off = mv2120_power_off; +} + +/* Warning: HP uses a wrong mach-type (=526) in their bootloader */ +MACHINE_START(MV2120, "HP Media Vault mv2120") + /* Maintainer: Martin Michlmayr <tbm@cyrius.com> */ + .phys_io = ORION5X_REGS_PHYS_BASE, + .io_pg_offst = ((ORION5X_REGS_VIRT_BASE) >> 18) & 0xFFFC, + .boot_params = 0x00000100, + .init_machine = mv2120_init, + .map_io = orion5x_map_io, + .init_irq = orion5x_init_irq, + .timer = &orion5x_timer, + .fixup = tag_fixup_mem32 +MACHINE_END diff --git a/arch/arm/mach-orion5x/pci.c b/arch/arm/mach-orion5x/pci.c index 9d5d39fa19c..256a4f68093 100644 --- a/arch/arm/mach-orion5x/pci.c +++ b/arch/arm/mach-orion5x/pci.c @@ -152,6 +152,8 @@ static int __init pcie_setup(struct pci_sys_data *sys) if (dev == MV88F5181_DEV_ID || dev == MV88F5182_DEV_ID) { printk(KERN_NOTICE "Applying Orion-1/Orion-NAS PCIe config " "read transaction workaround\n"); + orion5x_setup_pcie_wa_win(ORION5X_PCIE_WA_PHYS_BASE, + ORION5X_PCIE_WA_SIZE); pcie_ops.read = pcie_rd_conf_wa; } @@ -240,13 +242,13 @@ static int __init pcie_setup(struct pci_sys_data *sys) * PCI Address Decode Windows registers */ #define PCI_BAR_SIZE_DDR_CS(n) (((n) == 0) ? ORION5X_PCI_REG(0xc08) : \ - ((n) == 1) ? ORION5X_PCI_REG(0xd08) : \ - ((n) == 2) ? ORION5X_PCI_REG(0xc0c) : \ - ((n) == 3) ? ORION5X_PCI_REG(0xd0c) : 0) -#define PCI_BAR_REMAP_DDR_CS(n) (((n) ==0) ? ORION5X_PCI_REG(0xc48) : \ - ((n) == 1) ? ORION5X_PCI_REG(0xd48) : \ - ((n) == 2) ? ORION5X_PCI_REG(0xc4c) : \ - ((n) == 3) ? ORION5X_PCI_REG(0xd4c) : 0) + ((n) == 1) ? ORION5X_PCI_REG(0xd08) : \ + ((n) == 2) ? ORION5X_PCI_REG(0xc0c) : \ + ((n) == 3) ? ORION5X_PCI_REG(0xd0c) : 0) +#define PCI_BAR_REMAP_DDR_CS(n) (((n) == 0) ? ORION5X_PCI_REG(0xc48) : \ + ((n) == 1) ? ORION5X_PCI_REG(0xd48) : \ + ((n) == 2) ? ORION5X_PCI_REG(0xc4c) : \ + ((n) == 3) ? ORION5X_PCI_REG(0xd4c) : 0) #define PCI_BAR_ENABLE ORION5X_PCI_REG(0xc3c) #define PCI_ADDR_DECODE_CTRL ORION5X_PCI_REG(0xd3c) @@ -264,9 +266,11 @@ static int __init pcie_setup(struct pci_sys_data *sys) */ static DEFINE_SPINLOCK(orion5x_pci_lock); +static int orion5x_pci_cardbus_mode; + static int orion5x_pci_local_bus_nr(void) { - u32 conf = orion5x_read(PCI_P2P_CONF); + u32 conf = readl(PCI_P2P_CONF); return((conf & PCI_P2P_BUS_MASK) >> PCI_P2P_BUS_OFFS); } @@ -276,11 +280,11 @@ static int orion5x_pci_hw_rd_conf(int bus, int dev, u32 func, unsigned long flags; spin_lock_irqsave(&orion5x_pci_lock, flags); - orion5x_write(PCI_CONF_ADDR, PCI_CONF_BUS(bus) | - PCI_CONF_DEV(dev) | PCI_CONF_REG(where) | - PCI_CONF_FUNC(func) | PCI_CONF_ADDR_EN); + writel(PCI_CONF_BUS(bus) | + PCI_CONF_DEV(dev) | PCI_CONF_REG(where) | + PCI_CONF_FUNC(func) | PCI_CONF_ADDR_EN, PCI_CONF_ADDR); - *val = orion5x_read(PCI_CONF_DATA); + *val = readl(PCI_CONF_DATA); if (size == 1) *val = (*val >> (8*(where & 0x3))) & 0xff; @@ -300,9 +304,9 @@ static int orion5x_pci_hw_wr_conf(int bus, int dev, u32 func, spin_lock_irqsave(&orion5x_pci_lock, flags); - orion5x_write(PCI_CONF_ADDR, PCI_CONF_BUS(bus) | - PCI_CONF_DEV(dev) | PCI_CONF_REG(where) | - PCI_CONF_FUNC(func) | PCI_CONF_ADDR_EN); + writel(PCI_CONF_BUS(bus) | + PCI_CONF_DEV(dev) | PCI_CONF_REG(where) | + PCI_CONF_FUNC(func) | PCI_CONF_ADDR_EN, PCI_CONF_ADDR); if (size == 4) { __raw_writel(val, PCI_CONF_DATA); @@ -319,14 +323,30 @@ static int orion5x_pci_hw_wr_conf(int bus, int dev, u32 func, return ret; } +static int orion5x_pci_valid_config(int bus, u32 devfn) +{ + if (bus == orion5x_pci_local_bus_nr()) { + /* + * Don't go out for local device + */ + if (PCI_SLOT(devfn) == 0 && PCI_FUNC(devfn) != 0) + return 0; + + /* + * When the PCI signals are directly connected to a + * Cardbus slot, ignore all but device IDs 0 and 1. + */ + if (orion5x_pci_cardbus_mode && PCI_SLOT(devfn) > 1) + return 0; + } + + return 1; +} + static int orion5x_pci_rd_conf(struct pci_bus *bus, u32 devfn, int where, int size, u32 *val) { - /* - * Don't go out for local device - */ - if (bus->number == orion5x_pci_local_bus_nr() && - PCI_SLOT(devfn) == 0 && PCI_FUNC(devfn) != 0) { + if (!orion5x_pci_valid_config(bus->number, devfn)) { *val = 0xffffffff; return PCIBIOS_DEVICE_NOT_FOUND; } @@ -338,8 +358,7 @@ static int orion5x_pci_rd_conf(struct pci_bus *bus, u32 devfn, static int orion5x_pci_wr_conf(struct pci_bus *bus, u32 devfn, int where, int size, u32 val) { - if (bus->number == orion5x_pci_local_bus_nr() && - PCI_SLOT(devfn) == 0 && PCI_FUNC(devfn) != 0) + if (!orion5x_pci_valid_config(bus->number, devfn)) return PCIBIOS_DEVICE_NOT_FOUND; return orion5x_pci_hw_wr_conf(bus->number, PCI_SLOT(devfn), @@ -353,9 +372,9 @@ static struct pci_ops pci_ops = { static void __init orion5x_pci_set_bus_nr(int nr) { - u32 p2p = orion5x_read(PCI_P2P_CONF); + u32 p2p = readl(PCI_P2P_CONF); - if (orion5x_read(PCI_MODE) & PCI_MODE_PCIX) { + if (readl(PCI_MODE) & PCI_MODE_PCIX) { /* * PCI-X mode */ @@ -372,7 +391,7 @@ static void __init orion5x_pci_set_bus_nr(int nr) */ p2p &= ~PCI_P2P_BUS_MASK; p2p |= (nr << PCI_P2P_BUS_OFFS); - orion5x_write(PCI_P2P_CONF, p2p); + writel(p2p, PCI_P2P_CONF); } } @@ -399,7 +418,7 @@ static void __init orion5x_setup_pci_wins(struct mbus_dram_target_info *dram) * First, disable windows. */ win_enable = 0xffffffff; - orion5x_write(PCI_BAR_ENABLE, win_enable); + writel(win_enable, PCI_BAR_ENABLE); /* * Setup windows for DDR banks. @@ -425,10 +444,10 @@ static void __init orion5x_setup_pci_wins(struct mbus_dram_target_info *dram) */ reg = PCI_CONF_REG_BAR_HI_CS(cs->cs_index); orion5x_pci_hw_wr_conf(bus, 0, func, reg, 4, 0); - orion5x_write(PCI_BAR_SIZE_DDR_CS(cs->cs_index), - (cs->size - 1) & 0xfffff000); - orion5x_write(PCI_BAR_REMAP_DDR_CS(cs->cs_index), - cs->base & 0xfffff000); + writel((cs->size - 1) & 0xfffff000, + PCI_BAR_SIZE_DDR_CS(cs->cs_index)); + writel(cs->base & 0xfffff000, + PCI_BAR_REMAP_DDR_CS(cs->cs_index)); /* * Enable decode window for this chip select. @@ -439,7 +458,7 @@ static void __init orion5x_setup_pci_wins(struct mbus_dram_target_info *dram) /* * Re-enable decode windows. */ - orion5x_write(PCI_BAR_ENABLE, win_enable); + writel(win_enable, PCI_BAR_ENABLE); /* * Disable automatic update of address remaping when writing to BARs. @@ -522,6 +541,11 @@ static void __devinit rc_pci_fixup(struct pci_dev *dev) } DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_MARVELL, PCI_ANY_ID, rc_pci_fixup); +void __init orion5x_pci_set_cardbus_mode(void) +{ + orion5x_pci_cardbus_mode = 1; +} + int __init orion5x_pci_sys_setup(int nr, struct pci_sys_data *sys) { int ret = 0; diff --git a/arch/arm/mach-orion5x/rd88f5181l-fxo-setup.c b/arch/arm/mach-orion5x/rd88f5181l-fxo-setup.c new file mode 100644 index 00000000000..d50e3650a09 --- /dev/null +++ b/arch/arm/mach-orion5x/rd88f5181l-fxo-setup.c @@ -0,0 +1,161 @@ +/* + * arch/arm/mach-orion5x/rd88f5181l-fxo-setup.c + * + * Marvell Orion-VoIP FXO Reference Design Setup + * + * This file is licensed under the terms of the GNU General Public + * License version 2. This program is licensed "as is" without any + * warranty of any kind, whether express or implied. + */ + +#include <linux/kernel.h> +#include <linux/init.h> +#include <linux/platform_device.h> +#include <linux/pci.h> +#include <linux/irq.h> +#include <linux/mtd/physmap.h> +#include <linux/mv643xx_eth.h> +#include <asm/mach-types.h> +#include <asm/gpio.h> +#include <asm/leds.h> +#include <asm/mach/arch.h> +#include <asm/mach/pci.h> +#include <asm/arch/orion5x.h> +#include "common.h" +#include "mpp.h" + +/***************************************************************************** + * RD-88F5181L FXO Info + ****************************************************************************/ +/* + * 8M NOR flash Device bus boot chip select + */ +#define RD88F5181L_FXO_NOR_BOOT_BASE 0xff800000 +#define RD88F5181L_FXO_NOR_BOOT_SIZE SZ_8M + + +/***************************************************************************** + * 8M NOR Flash on Device bus Boot chip select + ****************************************************************************/ +static struct physmap_flash_data rd88f5181l_fxo_nor_boot_flash_data = { + .width = 1, +}; + +static struct resource rd88f5181l_fxo_nor_boot_flash_resource = { + .flags = IORESOURCE_MEM, + .start = RD88F5181L_FXO_NOR_BOOT_BASE, + .end = RD88F5181L_FXO_NOR_BOOT_BASE + + RD88F5181L_FXO_NOR_BOOT_SIZE - 1, +}; + +static struct platform_device rd88f5181l_fxo_nor_boot_flash = { + .name = "physmap-flash", + .id = 0, + .dev = { + .platform_data = &rd88f5181l_fxo_nor_boot_flash_data, + }, + .num_resources = 1, + .resource = &rd88f5181l_fxo_nor_boot_flash_resource, +}; + + +/***************************************************************************** + * General Setup + ****************************************************************************/ +static struct orion5x_mpp_mode rd88f5181l_fxo_mpp_modes[] __initdata = { + { 0, MPP_GPIO }, /* LED1 CardBus LED (front panel) */ + { 1, MPP_GPIO }, /* PCI_intA */ + { 2, MPP_GPIO }, /* Hard Reset / Factory Init*/ + { 3, MPP_GPIO }, /* FXS or DAA select */ + { 4, MPP_GPIO }, /* LED6 - phone LED (front panel) */ + { 5, MPP_GPIO }, /* LED5 - phone LED (front panel) */ + { 6, MPP_PCI_CLK }, /* CPU PCI refclk */ + { 7, MPP_PCI_CLK }, /* PCI/PCIe refclk */ + { 8, MPP_GPIO }, /* CardBus reset */ + { 9, MPP_GPIO }, /* GE_RXERR */ + { 10, MPP_GPIO }, /* LED2 MiniPCI LED (front panel) */ + { 11, MPP_GPIO }, /* Lifeline control */ + { 12, MPP_GIGE }, /* GE_TXD[4] */ + { 13, MPP_GIGE }, /* GE_TXD[5] */ + { 14, MPP_GIGE }, /* GE_TXD[6] */ + { 15, MPP_GIGE }, /* GE_TXD[7] */ + { 16, MPP_GIGE }, /* GE_RXD[4] */ + { 17, MPP_GIGE }, /* GE_RXD[5] */ + { 18, MPP_GIGE }, /* GE_RXD[6] */ + { 19, MPP_GIGE }, /* GE_RXD[7] */ + { -1 }, +}; + +static struct mv643xx_eth_platform_data rd88f5181l_fxo_eth_data = { + .phy_addr = -1, +}; + +static void __init rd88f5181l_fxo_init(void) +{ + /* + * Setup basic Orion functions. Need to be called early. + */ + orion5x_init(); + + orion5x_mpp_conf(rd88f5181l_fxo_mpp_modes); + + /* + * Configure peripherals. + */ + orion5x_ehci0_init(); + orion5x_eth_init(&rd88f5181l_fxo_eth_data); + orion5x_uart0_init(); + + orion5x_setup_dev_boot_win(RD88F5181L_FXO_NOR_BOOT_BASE, + RD88F5181L_FXO_NOR_BOOT_SIZE); + platform_device_register(&rd88f5181l_fxo_nor_boot_flash); +} + +static int __init +rd88f5181l_fxo_pci_map_irq(struct pci_dev *dev, u8 slot, u8 pin) +{ + int irq; + + /* + * Check for devices with hard-wired IRQs. + */ + irq = orion5x_pci_map_irq(dev, slot, pin); + if (irq != -1) + return irq; + + /* + * Mini-PCI / Cardbus slot. + */ + return gpio_to_irq(1); +} + +static struct hw_pci rd88f5181l_fxo_pci __initdata = { + .nr_controllers = 2, + .swizzle = pci_std_swizzle, + .setup = orion5x_pci_sys_setup, + .scan = orion5x_pci_sys_scan_bus, + .map_irq = rd88f5181l_fxo_pci_map_irq, +}; + +static int __init rd88f5181l_fxo_pci_init(void) +{ + if (machine_is_rd88f5181l_fxo()) { + orion5x_pci_set_cardbus_mode(); + pci_common_init(&rd88f5181l_fxo_pci); + } + + return 0; +} +subsys_initcall(rd88f5181l_fxo_pci_init); + +MACHINE_START(RD88F5181L_FXO, "Marvell Orion-VoIP FXO Reference Design") + /* Maintainer: Nicolas Pitre <nico@marvell.com> */ + .phys_io = ORION5X_REGS_PHYS_BASE, + .io_pg_offst = ((ORION5X_REGS_VIRT_BASE) >> 18) & 0xFFFC, + .boot_params = 0x00000100, + .init_machine = rd88f5181l_fxo_init, + .map_io = orion5x_map_io, + .init_irq = orion5x_init_irq, + .timer = &orion5x_timer, + .fixup = tag_fixup_mem32, +MACHINE_END diff --git a/arch/arm/mach-orion5x/rd88f5181l-ge-setup.c b/arch/arm/mach-orion5x/rd88f5181l-ge-setup.c new file mode 100644 index 00000000000..b56447d32e1 --- /dev/null +++ b/arch/arm/mach-orion5x/rd88f5181l-ge-setup.c @@ -0,0 +1,172 @@ +/* + * arch/arm/mach-orion5x/rd88f5181l-ge-setup.c + * + * Marvell Orion-VoIP GE Reference Design Setup + * + * This file is licensed under the terms of the GNU General Public + * License version 2. This program is licensed "as is" without any + * warranty of any kind, whether express or implied. + */ + +#include <linux/kernel.h> +#include <linux/init.h> +#include <linux/platform_device.h> +#include <linux/pci.h> +#include <linux/irq.h> +#include <linux/mtd/physmap.h> +#include <linux/mv643xx_eth.h> +#include <linux/i2c.h> +#include <asm/mach-types.h> +#include <asm/gpio.h> +#include <asm/leds.h> +#include <asm/mach/arch.h> +#include <asm/mach/pci.h> +#include <asm/arch/orion5x.h> +#include "common.h" +#include "mpp.h" + +/***************************************************************************** + * RD-88F5181L GE Info + ****************************************************************************/ +/* + * 16M NOR flash Device bus boot chip select + */ +#define RD88F5181L_GE_NOR_BOOT_BASE 0xff000000 +#define RD88F5181L_GE_NOR_BOOT_SIZE SZ_16M + + +/***************************************************************************** + * 16M NOR Flash on Device bus Boot chip select + ****************************************************************************/ +static struct physmap_flash_data rd88f5181l_ge_nor_boot_flash_data = { + .width = 1, +}; + +static struct resource rd88f5181l_ge_nor_boot_flash_resource = { + .flags = IORESOURCE_MEM, + .start = RD88F5181L_GE_NOR_BOOT_BASE, + .end = RD88F5181L_GE_NOR_BOOT_BASE + + RD88F5181L_GE_NOR_BOOT_SIZE - 1, +}; + +static struct platform_device rd88f5181l_ge_nor_boot_flash = { + .name = "physmap-flash", + .id = 0, + .dev = { + .platform_data = &rd88f5181l_ge_nor_boot_flash_data, + }, + .num_resources = 1, + .resource = &rd88f5181l_ge_nor_boot_flash_resource, +}; + + +/***************************************************************************** + * General Setup + ****************************************************************************/ +static struct orion5x_mpp_mode rd88f5181l_ge_mpp_modes[] __initdata = { + { 0, MPP_GPIO }, /* LED1 */ + { 1, MPP_GPIO }, /* LED5 */ + { 2, MPP_GPIO }, /* LED4 */ + { 3, MPP_GPIO }, /* LED3 */ + { 4, MPP_GPIO }, /* PCI_intA */ + { 5, MPP_GPIO }, /* RTC interrupt */ + { 6, MPP_PCI_CLK }, /* CPU PCI refclk */ + { 7, MPP_PCI_CLK }, /* PCI/PCIe refclk */ + { 8, MPP_GPIO }, /* 88e6131 interrupt */ + { 9, MPP_GPIO }, /* GE_RXERR */ + { 10, MPP_GPIO }, /* PCI_intB */ + { 11, MPP_GPIO }, /* LED2 */ + { 12, MPP_GIGE }, /* GE_TXD[4] */ + { 13, MPP_GIGE }, /* GE_TXD[5] */ + { 14, MPP_GIGE }, /* GE_TXD[6] */ + { 15, MPP_GIGE }, /* GE_TXD[7] */ + { 16, MPP_GIGE }, /* GE_RXD[4] */ + { 17, MPP_GIGE }, /* GE_RXD[5] */ + { 18, MPP_GIGE }, /* GE_RXD[6] */ + { 19, MPP_GIGE }, /* GE_RXD[7] */ + { -1 }, +}; + +static struct mv643xx_eth_platform_data rd88f5181l_ge_eth_data = { + .phy_addr = -1, +}; + +static struct i2c_board_info __initdata rd88f5181l_ge_i2c_rtc = { + I2C_BOARD_INFO("ds1338", 0x68), +}; + +static void __init rd88f5181l_ge_init(void) +{ + /* + * Setup basic Orion functions. Need to be called early. + */ + orion5x_init(); + + orion5x_mpp_conf(rd88f5181l_ge_mpp_modes); + + /* + * Configure peripherals. + */ + orion5x_ehci0_init(); + orion5x_eth_init(&rd88f5181l_ge_eth_data); + orion5x_i2c_init(); + orion5x_uart0_init(); + + orion5x_setup_dev_boot_win(RD88F5181L_GE_NOR_BOOT_BASE, + RD88F5181L_GE_NOR_BOOT_SIZE); + platform_device_register(&rd88f5181l_ge_nor_boot_flash); + + i2c_register_board_info(0, &rd88f5181l_ge_i2c_rtc, 1); +} + +static int __init +rd88f5181l_ge_pci_map_irq(struct pci_dev *dev, u8 slot, u8 pin) +{ + int irq; + + /* + * Check for devices with hard-wired IRQs. + */ + irq = orion5x_pci_map_irq(dev, slot, pin); + if (irq != -1) + return irq; + + /* + * Cardbus slot. + */ + if (pin == 1) + return gpio_to_irq(4); + else + return gpio_to_irq(10); +} + +static struct hw_pci rd88f5181l_ge_pci __initdata = { + .nr_controllers = 2, + .swizzle = pci_std_swizzle, + .setup = orion5x_pci_sys_setup, + .scan = orion5x_pci_sys_scan_bus, + .map_irq = rd88f5181l_ge_pci_map_irq, +}; + +static int __init rd88f5181l_ge_pci_init(void) +{ + if (machine_is_rd88f5181l_ge()) { + orion5x_pci_set_cardbus_mode(); + pci_common_init(&rd88f5181l_ge_pci); + } + + return 0; +} +subsys_initcall(rd88f5181l_ge_pci_init); + +MACHINE_START(RD88F5181L_GE, "Marvell Orion-VoIP GE Reference Design") + /* Maintainer: Lennert Buytenhek <buytenh@marvell.com> */ + .phys_io = ORION5X_REGS_PHYS_BASE, + .io_pg_offst = ((ORION5X_REGS_VIRT_BASE) >> 18) & 0xFFFC, + .boot_params = 0x00000100, + .init_machine = rd88f5181l_ge_init, + .map_io = orion5x_map_io, + .init_irq = orion5x_init_irq, + .timer = &orion5x_timer, + .fixup = tag_fixup_mem32, +MACHINE_END diff --git a/arch/arm/mach-orion5x/rd88f5182-setup.c b/arch/arm/mach-orion5x/rd88f5182-setup.c index 81abc1003aa..10ae6286426 100644 --- a/arch/arm/mach-orion5x/rd88f5182-setup.c +++ b/arch/arm/mach-orion5x/rd88f5182-setup.c @@ -26,6 +26,7 @@ #include <asm/mach/pci.h> #include <asm/arch/orion5x.h> #include "common.h" +#include "mpp.h" /***************************************************************************** * RD-88F5182 Info @@ -125,6 +126,7 @@ static int __init rd88f5182_dbgled_init(void) leds_event = rd88f5182_dbgled_event; } + return 0; } @@ -220,7 +222,6 @@ subsys_initcall(rd88f5182_pci_init); static struct mv643xx_eth_platform_data rd88f5182_eth_data = { .phy_addr = 8, - .force_phy_addr = 1, }; /***************************************************************************** @@ -234,15 +235,34 @@ static struct i2c_board_info __initdata rd88f5182_i2c_rtc = { * Sata ****************************************************************************/ static struct mv_sata_platform_data rd88f5182_sata_data = { - .n_ports = 2, + .n_ports = 2, }; /***************************************************************************** * General Setup ****************************************************************************/ - -static struct platform_device *rd88f5182_devices[] __initdata = { - &rd88f5182_nor_flash, +static struct orion5x_mpp_mode rd88f5182_mpp_modes[] __initdata = { + { 0, MPP_GPIO }, /* Debug Led */ + { 1, MPP_GPIO }, /* Reset Switch */ + { 2, MPP_UNUSED }, + { 3, MPP_GPIO }, /* RTC Int */ + { 4, MPP_GPIO }, + { 5, MPP_GPIO }, + { 6, MPP_GPIO }, /* PCI_intA */ + { 7, MPP_GPIO }, /* PCI_intB */ + { 8, MPP_UNUSED }, + { 9, MPP_UNUSED }, + { 10, MPP_UNUSED }, + { 11, MPP_UNUSED }, + { 12, MPP_SATA_LED }, /* SATA 0 presence */ + { 13, MPP_SATA_LED }, /* SATA 1 presence */ + { 14, MPP_SATA_LED }, /* SATA 0 active */ + { 15, MPP_SATA_LED }, /* SATA 1 active */ + { 16, MPP_UNUSED }, + { 17, MPP_UNUSED }, + { 18, MPP_UNUSED }, + { 19, MPP_UNUSED }, + { -1 }, }; static void __init rd88f5182_init(void) @@ -252,35 +272,9 @@ static void __init rd88f5182_init(void) */ orion5x_init(); - /* - * Setup the CPU address decode windows for our devices - */ - orion5x_setup_dev_boot_win(RD88F5182_NOR_BOOT_BASE, - RD88F5182_NOR_BOOT_SIZE); - orion5x_setup_dev1_win(RD88F5182_NOR_BASE, RD88F5182_NOR_SIZE); - - /* - * Open a special address decode windows for the PCIe WA. - */ - orion5x_setup_pcie_wa_win(ORION5X_PCIE_WA_PHYS_BASE, - ORION5X_PCIE_WA_SIZE); + orion5x_mpp_conf(rd88f5182_mpp_modes); /* - * Setup Multiplexing Pins -- - * MPP[0] Debug Led (GPIO - Out) - * MPP[1] Debug Led (GPIO - Out) - * MPP[2] N/A - * MPP[3] RTC_Int (GPIO - In) - * MPP[4] GPIO - * MPP[5] GPIO - * MPP[6] PCI_intA (GPIO - In) - * MPP[7] PCI_intB (GPIO - In) - * MPP[8-11] N/A - * MPP[12] SATA 0 presence Indication - * MPP[13] SATA 1 presence Indication - * MPP[14] SATA 0 active Indication - * MPP[15] SATA 1 active indication - * MPP[16-19] Not used * MPP[20] PCI Clock to MV88F5182 * MPP[21] PCI Clock to mini PCI CON11 * MPP[22] USB 0 over current indication @@ -289,16 +283,23 @@ static void __init rd88f5182_init(void) * MPP[25] USB 0 over current enable */ - orion5x_write(MPP_0_7_CTRL, 0x00000003); - orion5x_write(MPP_8_15_CTRL, 0x55550000); - orion5x_write(MPP_16_19_CTRL, 0x5555); + /* + * Configure peripherals. + */ + orion5x_ehci0_init(); + orion5x_ehci1_init(); + orion5x_eth_init(&rd88f5182_eth_data); + orion5x_i2c_init(); + orion5x_sata_init(&rd88f5182_sata_data); + orion5x_uart0_init(); - orion5x_gpio_set_valid_pins(0x000000fb); + orion5x_setup_dev_boot_win(RD88F5182_NOR_BOOT_BASE, + RD88F5182_NOR_BOOT_SIZE); + + orion5x_setup_dev1_win(RD88F5182_NOR_BASE, RD88F5182_NOR_SIZE); + platform_device_register(&rd88f5182_nor_flash); - platform_add_devices(rd88f5182_devices, ARRAY_SIZE(rd88f5182_devices)); i2c_register_board_info(0, &rd88f5182_i2c_rtc, 1); - orion5x_eth_init(&rd88f5182_eth_data); - orion5x_sata_init(&rd88f5182_sata_data); } MACHINE_START(RD88F5182, "Marvell Orion-NAS Reference Design") diff --git a/arch/arm/mach-orion5x/ts209-setup.c b/arch/arm/mach-orion5x/ts209-setup.c index 9afb41ee6e0..a9cef9703d5 100644 --- a/arch/arm/mach-orion5x/ts209-setup.c +++ b/arch/arm/mach-orion5x/ts209-setup.c @@ -28,6 +28,8 @@ #include <asm/mach/pci.h> #include <asm/arch/orion5x.h> #include "common.h" +#include "mpp.h" +#include "tsx09-common.h" #define QNAP_TS209_NOR_BOOT_BASE 0xf4000000 #define QNAP_TS209_NOR_BOOT_SIZE SZ_8M @@ -47,52 +49,54 @@ ***************************************************************************/ static struct mtd_partition qnap_ts209_partitions[] = { { - .name = "U-Boot", - .size = 0x00080000, - .offset = 0x00780000, - .mask_flags = MTD_WRITEABLE, + .name = "U-Boot", + .size = 0x00080000, + .offset = 0x00780000, + .mask_flags = MTD_WRITEABLE, }, { - .name = "Kernel", - .size = 0x00200000, - .offset = 0, + .name = "Kernel", + .size = 0x00200000, + .offset = 0, }, { - .name = "RootFS1", - .size = 0x00400000, - .offset = 0x00200000, + .name = "RootFS1", + .size = 0x00400000, + .offset = 0x00200000, }, { - .name = "RootFS2", - .size = 0x00100000, - .offset = 0x00600000, + .name = "RootFS2", + .size = 0x00100000, + .offset = 0x00600000, }, { - .name = "U-Boot Config", - .size = 0x00020000, - .offset = 0x00760000, + .name = "U-Boot Config", + .size = 0x00020000, + .offset = 0x00760000, }, { - .name = "NAS Config", - .size = 0x00060000, - .offset = 0x00700000, - .mask_flags = MTD_WRITEABLE, - } + .name = "NAS Config", + .size = 0x00060000, + .offset = 0x00700000, + .mask_flags = MTD_WRITEABLE, + }, }; static struct physmap_flash_data qnap_ts209_nor_flash_data = { - .width = 1, - .parts = qnap_ts209_partitions, - .nr_parts = ARRAY_SIZE(qnap_ts209_partitions) + .width = 1, + .parts = qnap_ts209_partitions, + .nr_parts = ARRAY_SIZE(qnap_ts209_partitions) }; static struct resource qnap_ts209_nor_flash_resource = { - .flags = IORESOURCE_MEM, - .start = QNAP_TS209_NOR_BOOT_BASE, - .end = QNAP_TS209_NOR_BOOT_BASE + QNAP_TS209_NOR_BOOT_SIZE - 1, + .flags = IORESOURCE_MEM, + .start = QNAP_TS209_NOR_BOOT_BASE, + .end = QNAP_TS209_NOR_BOOT_BASE + QNAP_TS209_NOR_BOOT_SIZE - 1, }; static struct platform_device qnap_ts209_nor_flash = { - .name = "physmap-flash", - .id = 0, - .dev = { .platform_data = &qnap_ts209_nor_flash_data, }, - .resource = &qnap_ts209_nor_flash_resource, - .num_resources = 1, + .name = "physmap-flash", + .id = 0, + .dev = { + .platform_data = &qnap_ts209_nor_flash_data, + }, + .resource = &qnap_ts209_nor_flash_resource, + .num_resources = 1, }; /***************************************************************************** @@ -164,12 +168,12 @@ static int __init qnap_ts209_pci_map_irq(struct pci_dev *dev, u8 slot, u8 pin) } static struct hw_pci qnap_ts209_pci __initdata = { - .nr_controllers = 2, - .preinit = qnap_ts209_pci_preinit, - .swizzle = pci_std_swizzle, - .setup = orion5x_pci_sys_setup, - .scan = orion5x_pci_sys_scan_bus, - .map_irq = qnap_ts209_pci_map_irq, + .nr_controllers = 2, + .preinit = qnap_ts209_pci_preinit, + .swizzle = pci_std_swizzle, + .setup = orion5x_pci_sys_setup, + .scan = orion5x_pci_sys_scan_bus, + .map_irq = qnap_ts209_pci_map_irq, }; static int __init qnap_ts209_pci_init(void) @@ -183,96 +187,6 @@ static int __init qnap_ts209_pci_init(void) subsys_initcall(qnap_ts209_pci_init); /***************************************************************************** - * Ethernet - ****************************************************************************/ - -static struct mv643xx_eth_platform_data qnap_ts209_eth_data = { - .phy_addr = 8, - .force_phy_addr = 1, -}; - -static int __init parse_hex_nibble(char n) -{ - if (n >= '0' && n <= '9') - return n - '0'; - - if (n >= 'A' && n <= 'F') - return n - 'A' + 10; - - if (n >= 'a' && n <= 'f') - return n - 'a' + 10; - - return -1; -} - -static int __init parse_hex_byte(const char *b) -{ - int hi; - int lo; - - hi = parse_hex_nibble(b[0]); - lo = parse_hex_nibble(b[1]); - - if (hi < 0 || lo < 0) - return -1; - - return (hi << 4) | lo; -} - -static int __init check_mac_addr(const char *addr_str) -{ - u_int8_t addr[6]; - int i; - - for (i = 0; i < 6; i++) { - int byte; - - /* - * Enforce "xx:xx:xx:xx:xx:xx\n" format. - */ - if (addr_str[(i * 3) + 2] != ((i < 5) ? ':' : '\n')) - return -1; - - byte = parse_hex_byte(addr_str + (i * 3)); - if (byte < 0) - return -1; - addr[i] = byte; - } - - printk(KERN_INFO "ts209: found ethernet mac address "); - for (i = 0; i < 6; i++) - printk("%.2x%s", addr[i], (i < 5) ? ":" : ".\n"); - - memcpy(qnap_ts209_eth_data.mac_addr, addr, 6); - - return 0; -} - -/* - * The 'NAS Config' flash partition has an ext2 filesystem which - * contains a file that has the ethernet MAC address in plain text - * (format "xx:xx:xx:xx:xx:xx\n".) - */ -static void __init ts209_find_mac_addr(void) -{ - unsigned long addr; - - for (addr = 0x00700000; addr < 0x00760000; addr += 1024) { - char *nor_page; - int ret = 0; - - nor_page = ioremap(QNAP_TS209_NOR_BOOT_BASE + addr, 1024); - if (nor_page != NULL) { - ret = check_mac_addr(nor_page); - iounmap(nor_page); - } - - if (ret == 0) - break; - } -} - -/***************************************************************************** * RTC S35390A on I2C bus ****************************************************************************/ @@ -280,7 +194,7 @@ static void __init ts209_find_mac_addr(void) static struct i2c_board_info __initdata qnap_ts209_i2c_rtc = { I2C_BOARD_INFO("s35390a", 0x30), - .irq = 0, + .irq = 0, }; /**************************************************************************** @@ -297,70 +211,63 @@ static struct gpio_keys_button qnap_ts209_buttons[] = { .gpio = QNAP_TS209_GPIO_KEY_MEDIA, .desc = "USB Copy Button", .active_low = 1, - }, - { + }, { .code = KEY_POWER, .gpio = QNAP_TS209_GPIO_KEY_RESET, .desc = "Reset Button", .active_low = 1, - } + }, }; static struct gpio_keys_platform_data qnap_ts209_button_data = { .buttons = qnap_ts209_buttons, - .nbuttons = ARRAY_SIZE(qnap_ts209_buttons), + .nbuttons = ARRAY_SIZE(qnap_ts209_buttons), }; static struct platform_device qnap_ts209_button_device = { .name = "gpio-keys", .id = -1, .num_resources = 0, - .dev = { .platform_data = &qnap_ts209_button_data, }, + .dev = { + .platform_data = &qnap_ts209_button_data, + }, }; /***************************************************************************** * SATA ****************************************************************************/ static struct mv_sata_platform_data qnap_ts209_sata_data = { - .n_ports = 2, + .n_ports = 2, }; /***************************************************************************** * General Setup ****************************************************************************/ - -static struct platform_device *qnap_ts209_devices[] __initdata = { - &qnap_ts209_nor_flash, - &qnap_ts209_button_device, +static struct orion5x_mpp_mode ts209_mpp_modes[] __initdata = { + { 0, MPP_UNUSED }, + { 1, MPP_GPIO }, /* USB copy button */ + { 2, MPP_GPIO }, /* Load defaults button */ + { 3, MPP_GPIO }, /* GPIO RTC */ + { 4, MPP_UNUSED }, + { 5, MPP_UNUSED }, + { 6, MPP_GPIO }, /* PCI Int A */ + { 7, MPP_GPIO }, /* PCI Int B */ + { 8, MPP_UNUSED }, + { 9, MPP_UNUSED }, + { 10, MPP_UNUSED }, + { 11, MPP_UNUSED }, + { 12, MPP_SATA_LED }, /* SATA 0 presence */ + { 13, MPP_SATA_LED }, /* SATA 1 presence */ + { 14, MPP_SATA_LED }, /* SATA 0 active */ + { 15, MPP_SATA_LED }, /* SATA 1 active */ + { 16, MPP_UART }, /* UART1 RXD */ + { 17, MPP_UART }, /* UART1 TXD */ + { 18, MPP_GPIO }, /* SW_RST */ + { 19, MPP_UNUSED }, + { -1 }, }; -/* - * QNAP TS-[12]09 specific power off method via UART1-attached PIC - */ - -#define UART1_REG(x) (UART1_VIRT_BASE + ((UART_##x) << 2)) - -static void qnap_ts209_power_off(void) -{ - /* 19200 baud divisor */ - const unsigned divisor = ((ORION5X_TCLK + (8 * 19200)) / (16 * 19200)); - - pr_info("%s: triggering power-off...\n", __func__); - - /* hijack uart1 and reset into sane state (19200,8n1) */ - orion5x_write(UART1_REG(LCR), 0x83); - orion5x_write(UART1_REG(DLL), divisor & 0xff); - orion5x_write(UART1_REG(DLM), (divisor >> 8) & 0xff); - orion5x_write(UART1_REG(LCR), 0x03); - orion5x_write(UART1_REG(IER), 0x00); - orion5x_write(UART1_REG(FCR), 0x00); - orion5x_write(UART1_REG(MCR), 0x00); - - /* send the power-off command 'A' to PIC */ - orion5x_write(UART1_REG(TX), 'A'); -} - static void __init qnap_ts209_init(void) { /* @@ -368,51 +275,33 @@ static void __init qnap_ts209_init(void) */ orion5x_init(); - /* - * Setup flash mapping - */ - orion5x_setup_dev_boot_win(QNAP_TS209_NOR_BOOT_BASE, - QNAP_TS209_NOR_BOOT_SIZE); - - /* - * Open a special address decode windows for the PCIe WA. - */ - orion5x_setup_pcie_wa_win(ORION5X_PCIE_WA_PHYS_BASE, - ORION5X_PCIE_WA_SIZE); + orion5x_mpp_conf(ts209_mpp_modes); /* - * Setup Multiplexing Pins -- - * MPP[0] Reserved - * MPP[1] USB copy button (0 active) - * MPP[2] Load defaults button (0 active) - * MPP[3] GPIO RTC - * MPP[4-5] Reserved - * MPP[6] PCI Int A - * MPP[7] PCI Int B - * MPP[8-11] Reserved - * MPP[12] SATA 0 presence - * MPP[13] SATA 1 presence - * MPP[14] SATA 0 active - * MPP[15] SATA 1 active - * MPP[16] UART1 RXD - * MPP[17] UART1 TXD - * MPP[18] SW_RST (0 active) - * MPP[19] Reserved * MPP[20] PCI clock 0 * MPP[21] PCI clock 1 * MPP[22] USB 0 over current * MPP[23-25] Reserved */ - orion5x_write(MPP_0_7_CTRL, 0x3); - orion5x_write(MPP_8_15_CTRL, 0x55550000); - orion5x_write(MPP_16_19_CTRL, 0x5500); - orion5x_gpio_set_valid_pins(0x3cc0fff); - /* register ts209 specific power-off method */ - pm_power_off = qnap_ts209_power_off; + /* + * Configure peripherals. + */ + orion5x_ehci0_init(); + orion5x_ehci1_init(); + qnap_tsx09_find_mac_addr(QNAP_TS209_NOR_BOOT_BASE + + qnap_ts209_partitions[5].offset, + qnap_ts209_partitions[5].size); + orion5x_eth_init(&qnap_tsx09_eth_data); + orion5x_i2c_init(); + orion5x_sata_init(&qnap_ts209_sata_data); + orion5x_uart0_init(); + + orion5x_setup_dev_boot_win(QNAP_TS209_NOR_BOOT_BASE, + QNAP_TS209_NOR_BOOT_SIZE); + platform_device_register(&qnap_ts209_nor_flash); - platform_add_devices(qnap_ts209_devices, - ARRAY_SIZE(qnap_ts209_devices)); + platform_device_register(&qnap_ts209_button_device); /* Get RTC IRQ and register the chip */ if (gpio_request(TS209_RTC_GPIO, "rtc") == 0) { @@ -425,14 +314,12 @@ static void __init qnap_ts209_init(void) pr_warning("qnap_ts209_init: failed to get RTC IRQ\n"); i2c_register_board_info(0, &qnap_ts209_i2c_rtc, 1); - ts209_find_mac_addr(); - orion5x_eth_init(&qnap_ts209_eth_data); - - orion5x_sata_init(&qnap_ts209_sata_data); + /* register tsx09 specific power-off method */ + pm_power_off = qnap_tsx09_power_off; } MACHINE_START(TS209, "QNAP TS-109/TS-209") - /* Maintainer: Byron Bradley <byron.bbradley@gmail.com> */ + /* Maintainer: Byron Bradley <byron.bbradley@gmail.com> */ .phys_io = ORION5X_REGS_PHYS_BASE, .io_pg_offst = ((ORION5X_REGS_VIRT_BASE) >> 18) & 0xFFFC, .boot_params = 0x00000100, diff --git a/arch/arm/mach-orion5x/ts409-setup.c b/arch/arm/mach-orion5x/ts409-setup.c new file mode 100644 index 00000000000..32f0ff073b7 --- /dev/null +++ b/arch/arm/mach-orion5x/ts409-setup.c @@ -0,0 +1,273 @@ +/* + * QNAP TS-409 Board Setup + * + * Maintainer: Sylver Bruneau <sylver.bruneau@gmail.com> + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License + * as published by the Free Software Foundation; either version + * 2 of the License, or (at your option) any later version. + */ + +#include <linux/kernel.h> +#include <linux/init.h> +#include <linux/platform_device.h> +#include <linux/pci.h> +#include <linux/irq.h> +#include <linux/mtd/physmap.h> +#include <linux/mv643xx_eth.h> +#include <linux/gpio_keys.h> +#include <linux/input.h> +#include <linux/i2c.h> +#include <linux/serial_reg.h> +#include <asm/mach-types.h> +#include <asm/gpio.h> +#include <asm/mach/arch.h> +#include <asm/mach/pci.h> +#include <asm/arch/orion5x.h> +#include "common.h" +#include "mpp.h" +#include "tsx09-common.h" + +/***************************************************************************** + * QNAP TS-409 Info + ****************************************************************************/ + +/* + * QNAP TS-409 hardware : + * - Marvell 88F5281-D0 + * - Marvell 88SX7042 SATA controller (PCIe) + * - Marvell 88E1118 Gigabit Ethernet PHY + * - RTC S35390A (@0x30) on I2C bus + * - 8MB NOR flash + * - 256MB of DDR-2 RAM + */ + +/* + * 8MB NOR flash Device bus boot chip select + */ + +#define QNAP_TS409_NOR_BOOT_BASE 0xff800000 +#define QNAP_TS409_NOR_BOOT_SIZE SZ_8M + +/**************************************************************************** + * 8MiB NOR flash. The struct mtd_partition is not in the same order as the + * partitions on the device because we want to keep compatability with + * existing QNAP firmware. + * + * Layout as used by QNAP: + * [2] 0x00000000-0x00200000 : "Kernel" + * [3] 0x00200000-0x00600000 : "RootFS1" + * [4] 0x00600000-0x00700000 : "RootFS2" + * [6] 0x00700000-0x00760000 : "NAS Config" (read-only) + * [5] 0x00760000-0x00780000 : "U-Boot Config" + * [1] 0x00780000-0x00800000 : "U-Boot" (read-only) + ***************************************************************************/ +static struct mtd_partition qnap_ts409_partitions[] = { + { + .name = "U-Boot", + .size = 0x00080000, + .offset = 0x00780000, + .mask_flags = MTD_WRITEABLE, + }, { + .name = "Kernel", + .size = 0x00200000, + .offset = 0, + }, { + .name = "RootFS1", + .size = 0x00400000, + .offset = 0x00200000, + }, { + .name = "RootFS2", + .size = 0x00100000, + .offset = 0x00600000, + }, { + .name = "U-Boot Config", + .size = 0x00020000, + .offset = 0x00760000, + }, { + .name = "NAS Config", + .size = 0x00060000, + .offset = 0x00700000, + .mask_flags = MTD_WRITEABLE, + }, +}; + +static struct physmap_flash_data qnap_ts409_nor_flash_data = { + .width = 1, + .parts = qnap_ts409_partitions, + .nr_parts = ARRAY_SIZE(qnap_ts409_partitions) +}; + +static struct resource qnap_ts409_nor_flash_resource = { + .flags = IORESOURCE_MEM, + .start = QNAP_TS409_NOR_BOOT_BASE, + .end = QNAP_TS409_NOR_BOOT_BASE + QNAP_TS409_NOR_BOOT_SIZE - 1, +}; + +static struct platform_device qnap_ts409_nor_flash = { + .name = "physmap-flash", + .id = 0, + .dev = { .platform_data = &qnap_ts409_nor_flash_data, }, + .num_resources = 1, + .resource = &qnap_ts409_nor_flash_resource, +}; + +/***************************************************************************** + * PCI + ****************************************************************************/ + +static int __init qnap_ts409_pci_map_irq(struct pci_dev *dev, u8 slot, u8 pin) +{ + int irq; + + /* + * Check for devices with hard-wired IRQs. + */ + irq = orion5x_pci_map_irq(dev, slot, pin); + if (irq != -1) + return irq; + + /* + * PCI isn't used on the TS-409 + */ + return -1; +} + +static struct hw_pci qnap_ts409_pci __initdata = { + .nr_controllers = 2, + .swizzle = pci_std_swizzle, + .setup = orion5x_pci_sys_setup, + .scan = orion5x_pci_sys_scan_bus, + .map_irq = qnap_ts409_pci_map_irq, +}; + +static int __init qnap_ts409_pci_init(void) +{ + if (machine_is_ts409()) + pci_common_init(&qnap_ts409_pci); + + return 0; +} + +subsys_initcall(qnap_ts409_pci_init); + +/***************************************************************************** + * RTC S35390A on I2C bus + ****************************************************************************/ + +#define TS409_RTC_GPIO 10 + +static struct i2c_board_info __initdata qnap_ts409_i2c_rtc = { + I2C_BOARD_INFO("s35390a", 0x30), +}; + +/**************************************************************************** + * GPIO Attached Keys + * Power button is attached to the PIC microcontroller + ****************************************************************************/ + +#define QNAP_TS409_GPIO_KEY_MEDIA 15 + +static struct gpio_keys_button qnap_ts409_buttons[] = { + { + .code = KEY_RESTART, + .gpio = QNAP_TS409_GPIO_KEY_MEDIA, + .desc = "USB Copy Button", + .active_low = 1, + }, +}; + +static struct gpio_keys_platform_data qnap_ts409_button_data = { + .buttons = qnap_ts409_buttons, + .nbuttons = ARRAY_SIZE(qnap_ts409_buttons), +}; + +static struct platform_device qnap_ts409_button_device = { + .name = "gpio-keys", + .id = -1, + .num_resources = 0, + .dev = { + .platform_data = &qnap_ts409_button_data, + }, +}; + +/***************************************************************************** + * General Setup + ****************************************************************************/ +static struct orion5x_mpp_mode ts409_mpp_modes[] __initdata = { + { 0, MPP_UNUSED }, + { 1, MPP_UNUSED }, + { 2, MPP_UNUSED }, + { 3, MPP_UNUSED }, + { 4, MPP_GPIO }, /* HDD 1 status */ + { 5, MPP_GPIO }, /* HDD 2 status */ + { 6, MPP_GPIO }, /* HDD 3 status */ + { 7, MPP_GPIO }, /* HDD 4 status */ + { 8, MPP_UNUSED }, + { 9, MPP_UNUSED }, + { 10, MPP_GPIO }, /* RTC int */ + { 11, MPP_UNUSED }, + { 12, MPP_UNUSED }, + { 13, MPP_UNUSED }, + { 14, MPP_GPIO }, /* SW_RST */ + { 15, MPP_GPIO }, /* USB copy button */ + { 16, MPP_UART }, /* UART1 RXD */ + { 17, MPP_UART }, /* UART1 TXD */ + { 18, MPP_UNUSED }, + { 19, MPP_UNUSED }, + { -1 }, +}; + +static void __init qnap_ts409_init(void) +{ + /* + * Setup basic Orion functions. Need to be called early. + */ + orion5x_init(); + + orion5x_mpp_conf(ts409_mpp_modes); + + /* + * Configure peripherals. + */ + orion5x_ehci0_init(); + qnap_tsx09_find_mac_addr(QNAP_TS409_NOR_BOOT_BASE + + qnap_ts409_partitions[5].offset, + qnap_ts409_partitions[5].size); + orion5x_eth_init(&qnap_tsx09_eth_data); + orion5x_i2c_init(); + orion5x_uart0_init(); + + orion5x_setup_dev_boot_win(QNAP_TS409_NOR_BOOT_BASE, + QNAP_TS409_NOR_BOOT_SIZE); + platform_device_register(&qnap_ts409_nor_flash); + + platform_device_register(&qnap_ts409_button_device); + + /* Get RTC IRQ and register the chip */ + if (gpio_request(TS409_RTC_GPIO, "rtc") == 0) { + if (gpio_direction_input(TS409_RTC_GPIO) == 0) + qnap_ts409_i2c_rtc.irq = gpio_to_irq(TS409_RTC_GPIO); + else + gpio_free(TS409_RTC_GPIO); + } + if (qnap_ts409_i2c_rtc.irq == 0) + pr_warning("qnap_ts409_init: failed to get RTC IRQ\n"); + i2c_register_board_info(0, &qnap_ts409_i2c_rtc, 1); + + /* register tsx09 specific power-off method */ + pm_power_off = qnap_tsx09_power_off; +} + +MACHINE_START(TS409, "QNAP TS-409") + /* Maintainer: Sylver Bruneau <sylver.bruneau@gmail.com> */ + .phys_io = ORION5X_REGS_PHYS_BASE, + .io_pg_offst = ((ORION5X_REGS_VIRT_BASE) >> 18) & 0xFFFC, + .boot_params = 0x00000100, + .init_machine = qnap_ts409_init, + .map_io = orion5x_map_io, + .init_irq = orion5x_init_irq, + .timer = &orion5x_timer, + .fixup = tag_fixup_mem32, +MACHINE_END diff --git a/arch/arm/mach-orion5x/ts78xx-setup.c b/arch/arm/mach-orion5x/ts78xx-setup.c new file mode 100644 index 00000000000..77e9f351f07 --- /dev/null +++ b/arch/arm/mach-orion5x/ts78xx-setup.c @@ -0,0 +1,277 @@ +/* + * arch/arm/mach-orion5x/ts78xx-setup.c + * + * Maintainer: Alexander Clouter <alex@digriz.org.uk> + * + * This file is licensed under the terms of the GNU General Public + * License version 2. This program is licensed "as is" without any + * warranty of any kind, whether express or implied. + */ + +#include <linux/kernel.h> +#include <linux/init.h> +#include <linux/platform_device.h> +#include <linux/mtd/physmap.h> +#include <linux/mv643xx_eth.h> +#include <linux/ata_platform.h> +#include <linux/m48t86.h> +#include <asm/mach-types.h> +#include <asm/mach/arch.h> +#include <asm/mach/map.h> +#include <asm/arch/orion5x.h> +#include "common.h" +#include "mpp.h" + +/***************************************************************************** + * TS-78xx Info + ****************************************************************************/ + +/* + * FPGA - lives where the PCI bus would be at ORION5X_PCI_MEM_PHYS_BASE + */ +#define TS78XX_FPGA_REGS_PHYS_BASE 0xe8000000 +#define TS78XX_FPGA_REGS_VIRT_BASE 0xff900000 +#define TS78XX_FPGA_REGS_SIZE SZ_1M + +#define TS78XX_FPGA_REGS_SYSCON_ID (TS78XX_FPGA_REGS_VIRT_BASE | 0x000) +#define TS78XX_FPGA_REGS_SYSCON_LCDI (TS78XX_FPGA_REGS_VIRT_BASE | 0x004) +#define TS78XX_FPGA_REGS_SYSCON_LCDO (TS78XX_FPGA_REGS_VIRT_BASE | 0x008) + +#define TS78XX_FPGA_REGS_RTC_CTRL (TS78XX_FPGA_REGS_VIRT_BASE | 0x808) +#define TS78XX_FPGA_REGS_RTC_DATA (TS78XX_FPGA_REGS_VIRT_BASE | 0x80c) + +/* + * 512kB NOR flash Device + */ +#define TS78XX_NOR_BOOT_BASE 0xff800000 +#define TS78XX_NOR_BOOT_SIZE SZ_512K + +/***************************************************************************** + * I/O Address Mapping + ****************************************************************************/ +static struct map_desc ts78xx_io_desc[] __initdata = { + { + .virtual = TS78XX_FPGA_REGS_VIRT_BASE, + .pfn = __phys_to_pfn(TS78XX_FPGA_REGS_PHYS_BASE), + .length = TS78XX_FPGA_REGS_SIZE, + .type = MT_DEVICE, + }, +}; + +void __init ts78xx_map_io(void) +{ + orion5x_map_io(); + iotable_init(ts78xx_io_desc, ARRAY_SIZE(ts78xx_io_desc)); +} + +/***************************************************************************** + * 512kB NOR Boot Flash - the chip is a M25P40 + ****************************************************************************/ +static struct mtd_partition ts78xx_nor_boot_flash_resources[] = { + { + .name = "ts-bootrom", + .offset = 0, + /* only the first 256kB is used */ + .size = SZ_256K, + .mask_flags = MTD_WRITEABLE, + }, +}; + +static struct physmap_flash_data ts78xx_nor_boot_flash_data = { + .width = 1, + .parts = ts78xx_nor_boot_flash_resources, + .nr_parts = ARRAY_SIZE(ts78xx_nor_boot_flash_resources), +}; + +static struct resource ts78xx_nor_boot_flash_resource = { + .flags = IORESOURCE_MEM, + .start = TS78XX_NOR_BOOT_BASE, + .end = TS78XX_NOR_BOOT_BASE + TS78XX_NOR_BOOT_SIZE - 1, +}; + +static struct platform_device ts78xx_nor_boot_flash = { + .name = "physmap-flash", + .id = -1, + .dev = { + .platform_data = &ts78xx_nor_boot_flash_data, + }, + .num_resources = 1, + .resource = &ts78xx_nor_boot_flash_resource, +}; + +/***************************************************************************** + * Ethernet + ****************************************************************************/ +static struct mv643xx_eth_platform_data ts78xx_eth_data = { + .phy_addr = 0, + .force_phy_addr = 1, +}; + +/***************************************************************************** + * RTC M48T86 - nicked^Wborrowed from arch/arm/mach-ep93xx/ts72xx.c + ****************************************************************************/ +#ifdef CONFIG_RTC_DRV_M48T86 +static unsigned char ts78xx_rtc_readbyte(unsigned long addr) +{ + writeb(addr, TS78XX_FPGA_REGS_RTC_CTRL); + return readb(TS78XX_FPGA_REGS_RTC_DATA); +} + +static void ts78xx_rtc_writebyte(unsigned char value, unsigned long addr) +{ + writeb(addr, TS78XX_FPGA_REGS_RTC_CTRL); + writeb(value, TS78XX_FPGA_REGS_RTC_DATA); +} + +static struct m48t86_ops ts78xx_rtc_ops = { + .readbyte = ts78xx_rtc_readbyte, + .writebyte = ts78xx_rtc_writebyte, +}; + +static struct platform_device ts78xx_rtc_device = { + .name = "rtc-m48t86", + .id = -1, + .dev = { + .platform_data = &ts78xx_rtc_ops, + }, + .num_resources = 0, +}; + +/* + * TS uses some of the user storage space on the RTC chip so see if it is + * present; as it's an optional feature at purchase time and not all boards + * will have it present + * + * I've used the method TS use in their rtc7800.c example for the detection + * + * TODO: track down a guinea pig without an RTC to see if we can work out a + * better RTC detection routine + */ +static int __init ts78xx_rtc_init(void) +{ + unsigned char tmp_rtc0, tmp_rtc1; + + tmp_rtc0 = ts78xx_rtc_readbyte(126); + tmp_rtc1 = ts78xx_rtc_readbyte(127); + + ts78xx_rtc_writebyte(0x00, 126); + ts78xx_rtc_writebyte(0x55, 127); + if (ts78xx_rtc_readbyte(127) == 0x55) { + ts78xx_rtc_writebyte(0xaa, 127); + if (ts78xx_rtc_readbyte(127) == 0xaa + && ts78xx_rtc_readbyte(126) == 0x00) { + ts78xx_rtc_writebyte(tmp_rtc0, 126); + ts78xx_rtc_writebyte(tmp_rtc1, 127); + platform_device_register(&ts78xx_rtc_device); + return 1; + } + } + + return 0; +}; +#else +static int __init ts78xx_rtc_init(void) +{ + return 0; +} +#endif + +/***************************************************************************** + * SATA + ****************************************************************************/ +static struct mv_sata_platform_data ts78xx_sata_data = { + .n_ports = 2, +}; + +/***************************************************************************** + * print some information regarding the board + ****************************************************************************/ +static void __init ts78xx_print_board_id(void) +{ + unsigned int board_info; + + board_info = readl(TS78XX_FPGA_REGS_SYSCON_ID); + printk(KERN_INFO "TS-78xx Info: FPGA rev=%.2x, Board Magic=%.6x, ", + board_info & 0xff, + (board_info >> 8) & 0xffffff); + board_info = readl(TS78XX_FPGA_REGS_SYSCON_LCDI); + printk("JP1=%d, JP2=%d\n", + (board_info >> 30) & 0x1, + (board_info >> 31) & 0x1); +}; + +/***************************************************************************** + * General Setup + ****************************************************************************/ +static struct orion5x_mpp_mode ts78xx_mpp_modes[] __initdata = { + { 0, MPP_UNUSED }, + { 1, MPP_GPIO }, /* JTAG Clock */ + { 2, MPP_GPIO }, /* JTAG Data In */ + { 3, MPP_GPIO }, /* Lat ECP2 256 FPGA - PB2B */ + { 4, MPP_GPIO }, /* JTAG Data Out */ + { 5, MPP_GPIO }, /* JTAG TMS */ + { 6, MPP_GPIO }, /* Lat ECP2 256 FPGA - PB31A_CLK4+ */ + { 7, MPP_GPIO }, /* Lat ECP2 256 FPGA - PB22B */ + { 8, MPP_UNUSED }, + { 9, MPP_UNUSED }, + { 10, MPP_UNUSED }, + { 11, MPP_UNUSED }, + { 12, MPP_UNUSED }, + { 13, MPP_UNUSED }, + { 14, MPP_UNUSED }, + { 15, MPP_UNUSED }, + { 16, MPP_UART }, + { 17, MPP_UART }, + { 18, MPP_UART }, + { 19, MPP_UART }, + { -1 }, +}; + +static void __init ts78xx_init(void) +{ + /* + * Setup basic Orion functions. Need to be called early. + */ + orion5x_init(); + + ts78xx_print_board_id(); + + orion5x_mpp_conf(ts78xx_mpp_modes); + + /* + * MPP[20] PCI Clock Out 1 + * MPP[21] PCI Clock Out 0 + * MPP[22] Unused + * MPP[23] Unused + * MPP[24] Unused + * MPP[25] Unused + */ + + /* + * Configure peripherals. + */ + orion5x_ehci0_init(); + orion5x_ehci1_init(); + orion5x_eth_init(&ts78xx_eth_data); + orion5x_sata_init(&ts78xx_sata_data); + orion5x_uart0_init(); + orion5x_uart1_init(); + + orion5x_setup_dev_boot_win(TS78XX_NOR_BOOT_BASE, + TS78XX_NOR_BOOT_SIZE); + platform_device_register(&ts78xx_nor_boot_flash); + + if (!ts78xx_rtc_init()) + printk(KERN_INFO "TS-78xx RTC not detected or enabled\n"); +} + +MACHINE_START(TS78XX, "Technologic Systems TS-78xx SBC") + /* Maintainer: Alexander Clouter <alex@digriz.org.uk> */ + .phys_io = ORION5X_REGS_PHYS_BASE, + .io_pg_offst = ((ORION5X_REGS_VIRT_BASE) >> 18) & 0xFFFC, + .boot_params = 0x00000100, + .init_machine = ts78xx_init, + .map_io = ts78xx_map_io, + .init_irq = orion5x_init_irq, + .timer = &orion5x_timer, +MACHINE_END diff --git a/arch/arm/mach-orion5x/tsx09-common.c b/arch/arm/mach-orion5x/tsx09-common.c new file mode 100644 index 00000000000..83feac3147a --- /dev/null +++ b/arch/arm/mach-orion5x/tsx09-common.c @@ -0,0 +1,133 @@ +/* + * QNAP TS-x09 Boards common functions + * + * Maintainers: Lennert Buytenhek <buytenh@marvell.com> + * Byron Bradley <byron.bbradley@gmail.com> + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License + * as published by the Free Software Foundation; either version + * 2 of the License, or (at your option) any later version. + */ + +#include <linux/kernel.h> +#include <linux/pci.h> +#include <linux/mv643xx_eth.h> +#include <linux/timex.h> +#include <linux/serial_reg.h> +#include "tsx09-common.h" + +/***************************************************************************** + * QNAP TS-x09 specific power off method via UART1-attached PIC + ****************************************************************************/ + +#define UART1_REG(x) (UART1_VIRT_BASE + ((UART_##x) << 2)) + +void qnap_tsx09_power_off(void) +{ + /* 19200 baud divisor */ + const unsigned divisor = ((ORION5X_TCLK + (8 * 19200)) / (16 * 19200)); + + pr_info("%s: triggering power-off...\n", __func__); + + /* hijack uart1 and reset into sane state (19200,8n1) */ + writel(0x83, UART1_REG(LCR)); + writel(divisor & 0xff, UART1_REG(DLL)); + writel((divisor >> 8) & 0xff, UART1_REG(DLM)); + writel(0x03, UART1_REG(LCR)); + writel(0x00, UART1_REG(IER)); + writel(0x00, UART1_REG(FCR)); + writel(0x00, UART1_REG(MCR)); + + /* send the power-off command 'A' to PIC */ + writel('A', UART1_REG(TX)); +} + +/***************************************************************************** + * Ethernet + ****************************************************************************/ + +struct mv643xx_eth_platform_data qnap_tsx09_eth_data = { + .phy_addr = 8, +}; + +static int __init qnap_tsx09_parse_hex_nibble(char n) +{ + if (n >= '0' && n <= '9') + return n - '0'; + + if (n >= 'A' && n <= 'F') + return n - 'A' + 10; + + if (n >= 'a' && n <= 'f') + return n - 'a' + 10; + + return -1; +} + +static int __init qnap_tsx09_parse_hex_byte(const char *b) +{ + int hi; + int lo; + + hi = qnap_tsx09_parse_hex_nibble(b[0]); + lo = qnap_tsx09_parse_hex_nibble(b[1]); + + if (hi < 0 || lo < 0) + return -1; + + return (hi << 4) | lo; +} + +static int __init qnap_tsx09_check_mac_addr(const char *addr_str) +{ + u_int8_t addr[6]; + int i; + + for (i = 0; i < 6; i++) { + int byte; + + /* + * Enforce "xx:xx:xx:xx:xx:xx\n" format. + */ + if (addr_str[(i * 3) + 2] != ((i < 5) ? ':' : '\n')) + return -1; + + byte = qnap_tsx09_parse_hex_byte(addr_str + (i * 3)); + if (byte < 0) + return -1; + addr[i] = byte; + } + + printk(KERN_INFO "tsx09: found ethernet mac address "); + for (i = 0; i < 6; i++) + printk("%.2x%s", addr[i], (i < 5) ? ":" : ".\n"); + + memcpy(qnap_tsx09_eth_data.mac_addr, addr, 6); + + return 0; +} + +/* + * The 'NAS Config' flash partition has an ext2 filesystem which + * contains a file that has the ethernet MAC address in plain text + * (format "xx:xx:xx:xx:xx:xx\n"). + */ +void __init qnap_tsx09_find_mac_addr(u32 mem_base, u32 size) +{ + unsigned long addr; + + for (addr = mem_base; addr < (mem_base + size); addr += 1024) { + char *nor_page; + int ret = 0; + + nor_page = ioremap(addr, 1024); + if (nor_page != NULL) { + ret = qnap_tsx09_check_mac_addr(nor_page); + iounmap(nor_page); + } + + if (ret == 0) + break; + } +} diff --git a/arch/arm/mach-orion5x/tsx09-common.h b/arch/arm/mach-orion5x/tsx09-common.h new file mode 100644 index 00000000000..0984264616f --- /dev/null +++ b/arch/arm/mach-orion5x/tsx09-common.h @@ -0,0 +1,20 @@ +#ifndef __ARCH_ORION5X_TSX09_COMMON_H +#define __ARCH_ORION5X_TSX09_COMMON_H + +/* + * QNAP TS-x09 Boards power-off function + */ +extern void qnap_tsx09_power_off(void); + +/* + * QNAP TS-x09 Boards function to find Ethernet MAC address in flash memory + */ +extern void __init qnap_tsx09_find_mac_addr(u32 mem_base, u32 size); + +/* + * QNAP TS-x09 Boards ethernet declaration + */ +extern struct mv643xx_eth_platform_data qnap_tsx09_eth_data; + + +#endif diff --git a/arch/arm/mach-orion5x/wnr854t-setup.c b/arch/arm/mach-orion5x/wnr854t-setup.c new file mode 100644 index 00000000000..1af093ff8cf --- /dev/null +++ b/arch/arm/mach-orion5x/wnr854t-setup.c @@ -0,0 +1,164 @@ +/* + * arch/arm/mach-orion5x/wnr854t-setup.c + * + * This file is licensed under the terms of the GNU General Public + * License version 2. This program is licensed "as is" without any + * warranty of any kind, whether express or implied. + */ + +#include <linux/kernel.h> +#include <linux/init.h> +#include <linux/platform_device.h> +#include <linux/pci.h> +#include <linux/irq.h> +#include <linux/delay.h> +#include <linux/mtd/physmap.h> +#include <linux/mv643xx_eth.h> +#include <asm/mach-types.h> +#include <asm/gpio.h> +#include <asm/mach/arch.h> +#include <asm/mach/pci.h> +#include <asm/arch/orion5x.h> +#include "common.h" +#include "mpp.h" + +static struct orion5x_mpp_mode wnr854t_mpp_modes[] __initdata = { + { 0, MPP_GPIO }, /* Power LED green (0=on) */ + { 1, MPP_GPIO }, /* Reset Button (0=off) */ + { 2, MPP_GPIO }, /* Power LED blink (0=off) */ + { 3, MPP_GPIO }, /* WAN Status LED amber (0=off) */ + { 4, MPP_GPIO }, /* PCI int */ + { 5, MPP_GPIO }, /* ??? */ + { 6, MPP_GPIO }, /* ??? */ + { 7, MPP_GPIO }, /* ??? */ + { 8, MPP_UNUSED }, /* ??? */ + { 9, MPP_GIGE }, /* GE_RXERR */ + { 10, MPP_UNUSED }, /* ??? */ + { 11, MPP_UNUSED }, /* ??? */ + { 12, MPP_GIGE }, /* GE_TXD[4] */ + { 13, MPP_GIGE }, /* GE_TXD[5] */ + { 14, MPP_GIGE }, /* GE_TXD[6] */ + { 15, MPP_GIGE }, /* GE_TXD[7] */ + { 16, MPP_GIGE }, /* GE_RXD[4] */ + { 17, MPP_GIGE }, /* GE_RXD[5] */ + { 18, MPP_GIGE }, /* GE_RXD[6] */ + { 19, MPP_GIGE }, /* GE_RXD[7] */ + { -1 }, +}; + +/* + * 8M NOR flash Device bus boot chip select + */ +#define WNR854T_NOR_BOOT_BASE 0xf4000000 +#define WNR854T_NOR_BOOT_SIZE SZ_8M + +static struct mtd_partition wnr854t_nor_flash_partitions[] = { + { + .name = "kernel", + .offset = 0x00000000, + .size = 0x00100000, + }, { + .name = "rootfs", + .offset = 0x00100000, + .size = 0x00660000, + }, { + .name = "uboot", + .offset = 0x00760000, + .size = 0x00040000, + }, +}; + +static struct physmap_flash_data wnr854t_nor_flash_data = { + .width = 2, + .parts = wnr854t_nor_flash_partitions, + .nr_parts = ARRAY_SIZE(wnr854t_nor_flash_partitions), +}; + +static struct resource wnr854t_nor_flash_resource = { + .flags = IORESOURCE_MEM, + .start = WNR854T_NOR_BOOT_BASE, + .end = WNR854T_NOR_BOOT_BASE + WNR854T_NOR_BOOT_SIZE - 1, +}; + +static struct platform_device wnr854t_nor_flash = { + .name = "physmap-flash", + .id = 0, + .dev = { + .platform_data = &wnr854t_nor_flash_data, + }, + .num_resources = 1, + .resource = &wnr854t_nor_flash_resource, +}; + +static struct mv643xx_eth_platform_data wnr854t_eth_data = { + .phy_addr = -1, +}; + +static void __init wnr854t_init(void) +{ + /* + * Setup basic Orion functions. Need to be called early. + */ + orion5x_init(); + + orion5x_mpp_conf(wnr854t_mpp_modes); + + /* + * Configure peripherals. + */ + orion5x_eth_init(&wnr854t_eth_data); + orion5x_uart0_init(); + + orion5x_setup_dev_boot_win(WNR854T_NOR_BOOT_BASE, + WNR854T_NOR_BOOT_SIZE); + platform_device_register(&wnr854t_nor_flash); +} + +static int __init wnr854t_pci_map_irq(struct pci_dev *dev, u8 slot, u8 pin) +{ + int irq; + + /* + * Check for devices with hard-wired IRQs. + */ + irq = orion5x_pci_map_irq(dev, slot, pin); + if (irq != -1) + return irq; + + /* + * Mini-PCI slot. + */ + if (slot == 7) + return gpio_to_irq(4); + + return -1; +} + +static struct hw_pci wnr854t_pci __initdata = { + .nr_controllers = 2, + .swizzle = pci_std_swizzle, + .setup = orion5x_pci_sys_setup, + .scan = orion5x_pci_sys_scan_bus, + .map_irq = wnr854t_pci_map_irq, +}; + +static int __init wnr854t_pci_init(void) +{ + if (machine_is_wnr854t()) + pci_common_init(&wnr854t_pci); + + return 0; +} +subsys_initcall(wnr854t_pci_init); + +MACHINE_START(WNR854T, "Netgear WNR854T") + /* Maintainer: Imre Kaloz <kaloz@openwrt.org> */ + .phys_io = ORION5X_REGS_PHYS_BASE, + .io_pg_offst = ((ORION5X_REGS_VIRT_BASE) >> 18) & 0xFFFC, + .boot_params = 0x00000100, + .init_machine = wnr854t_init, + .map_io = orion5x_map_io, + .init_irq = orion5x_init_irq, + .timer = &orion5x_timer, + .fixup = tag_fixup_mem32, +MACHINE_END diff --git a/arch/arm/mach-orion5x/wrt350n-v2-setup.c b/arch/arm/mach-orion5x/wrt350n-v2-setup.c new file mode 100644 index 00000000000..aeab55c6a82 --- /dev/null +++ b/arch/arm/mach-orion5x/wrt350n-v2-setup.c @@ -0,0 +1,173 @@ +/* + * arch/arm/mach-orion5x/wrt350n-v2-setup.c + * + * This file is licensed under the terms of the GNU General Public + * License version 2. This program is licensed "as is" without any + * warranty of any kind, whether express or implied. + */ + +#include <linux/kernel.h> +#include <linux/init.h> +#include <linux/platform_device.h> +#include <linux/pci.h> +#include <linux/irq.h> +#include <linux/delay.h> +#include <linux/mtd/physmap.h> +#include <linux/mv643xx_eth.h> +#include <asm/mach-types.h> +#include <asm/gpio.h> +#include <asm/mach/arch.h> +#include <asm/mach/pci.h> +#include <asm/arch/orion5x.h> +#include "common.h" +#include "mpp.h" + +static struct orion5x_mpp_mode wrt350n_v2_mpp_modes[] __initdata = { + { 0, MPP_GPIO }, /* Power LED green (0=on) */ + { 1, MPP_GPIO }, /* Security LED (0=on) */ + { 2, MPP_GPIO }, /* Internal Button (0=on) */ + { 3, MPP_GPIO }, /* Reset Button (0=on) */ + { 4, MPP_GPIO }, /* PCI int */ + { 5, MPP_GPIO }, /* Power LED orange (0=on) */ + { 6, MPP_GPIO }, /* USB LED (0=on) */ + { 7, MPP_GPIO }, /* Wireless LED (0=on) */ + { 8, MPP_UNUSED }, /* ??? */ + { 9, MPP_GIGE }, /* GE_RXERR */ + { 10, MPP_UNUSED }, /* ??? */ + { 11, MPP_UNUSED }, /* ??? */ + { 12, MPP_GIGE }, /* GE_TXD[4] */ + { 13, MPP_GIGE }, /* GE_TXD[5] */ + { 14, MPP_GIGE }, /* GE_TXD[6] */ + { 15, MPP_GIGE }, /* GE_TXD[7] */ + { 16, MPP_GIGE }, /* GE_RXD[4] */ + { 17, MPP_GIGE }, /* GE_RXD[5] */ + { 18, MPP_GIGE }, /* GE_RXD[6] */ + { 19, MPP_GIGE }, /* GE_RXD[7] */ + { -1 }, +}; + +/* + * 8M NOR flash Device bus boot chip select + */ +#define WRT350N_V2_NOR_BOOT_BASE 0xf4000000 +#define WRT350N_V2_NOR_BOOT_SIZE SZ_8M + +static struct mtd_partition wrt350n_v2_nor_flash_partitions[] = { + { + .name = "kernel", + .offset = 0x00000000, + .size = 0x00760000, + }, { + .name = "rootfs", + .offset = 0x001a0000, + .size = 0x005c0000, + }, { + .name = "lang", + .offset = 0x00760000, + .size = 0x00040000, + }, { + .name = "nvram", + .offset = 0x007a0000, + .size = 0x00020000, + }, { + .name = "u-boot", + .offset = 0x007c0000, + .size = 0x00040000, + }, +}; + +static struct physmap_flash_data wrt350n_v2_nor_flash_data = { + .width = 1, + .parts = wrt350n_v2_nor_flash_partitions, + .nr_parts = ARRAY_SIZE(wrt350n_v2_nor_flash_partitions), +}; + +static struct resource wrt350n_v2_nor_flash_resource = { + .flags = IORESOURCE_MEM, + .start = WRT350N_V2_NOR_BOOT_BASE, + .end = WRT350N_V2_NOR_BOOT_BASE + WRT350N_V2_NOR_BOOT_SIZE - 1, +}; + +static struct platform_device wrt350n_v2_nor_flash = { + .name = "physmap-flash", + .id = 0, + .dev = { + .platform_data = &wrt350n_v2_nor_flash_data, + }, + .num_resources = 1, + .resource = &wrt350n_v2_nor_flash_resource, +}; + +static struct mv643xx_eth_platform_data wrt350n_v2_eth_data = { + .phy_addr = -1, +}; + +static void __init wrt350n_v2_init(void) +{ + /* + * Setup basic Orion functions. Need to be called early. + */ + orion5x_init(); + + orion5x_mpp_conf(wrt350n_v2_mpp_modes); + + /* + * Configure peripherals. + */ + orion5x_ehci0_init(); + orion5x_eth_init(&wrt350n_v2_eth_data); + orion5x_uart0_init(); + + orion5x_setup_dev_boot_win(WRT350N_V2_NOR_BOOT_BASE, + WRT350N_V2_NOR_BOOT_SIZE); + platform_device_register(&wrt350n_v2_nor_flash); +} + +static int __init wrt350n_v2_pci_map_irq(struct pci_dev *dev, u8 slot, u8 pin) +{ + int irq; + + /* + * Check for devices with hard-wired IRQs. + */ + irq = orion5x_pci_map_irq(dev, slot, pin); + if (irq != -1) + return irq; + + /* + * Mini-PCI slot. + */ + if (slot == 7) + return gpio_to_irq(4); + + return -1; +} + +static struct hw_pci wrt350n_v2_pci __initdata = { + .nr_controllers = 2, + .swizzle = pci_std_swizzle, + .setup = orion5x_pci_sys_setup, + .scan = orion5x_pci_sys_scan_bus, + .map_irq = wrt350n_v2_pci_map_irq, +}; + +static int __init wrt350n_v2_pci_init(void) +{ + if (machine_is_wrt350n_v2()) + pci_common_init(&wrt350n_v2_pci); + + return 0; +} +subsys_initcall(wrt350n_v2_pci_init); + +MACHINE_START(WRT350N_V2, "Linksys WRT350N v2") + /* Maintainer: Lennert Buytenhek <buytenh@marvell.com> */ + .phys_io = ORION5X_REGS_PHYS_BASE, + .io_pg_offst = ((ORION5X_REGS_VIRT_BASE) >> 18) & 0xFFFC, + .boot_params = 0x00000100, + .init_machine = wrt350n_v2_init, + .map_io = orion5x_map_io, + .init_irq = orion5x_init_irq, + .timer = &orion5x_timer, + .fixup = tag_fixup_mem32, +MACHINE_END diff --git a/arch/arm/mach-s3c2410/Kconfig b/arch/arm/mach-s3c2410/Kconfig index cd3dc0834b3..99fdc736698 100644 --- a/arch/arm/mach-s3c2410/Kconfig +++ b/arch/arm/mach-s3c2410/Kconfig @@ -37,6 +37,17 @@ config S3C2410_CLOCK help Clock code for the S3C2410, and similar processors +config SIMTEC_NOR + bool + help + Internal node to specify machine has simtec NOR mapping + +config MACH_BAST_IDE + bool + select HAVE_PATA_PLATFORM + help + Internal node for machines with an BAST style IDE + interface menu "S3C2410 Machines" @@ -61,15 +72,18 @@ config PM_H1940 Internal node for H1940 and related PM config MACH_N30 - bool "Acer N30" + bool "Acer N30 family" select CPU_S3C2410 help - Say Y here if you are using the Acer N30 + Say Y here if you want suppt for the Acer N30, Acer N35, + Navman PiN570, Yakumo AlphaX or Airis NC05 PDAs. config ARCH_BAST bool "Simtec Electronics BAST (EB2410ITX)" select CPU_S3C2410 select PM_SIMTEC if PM + select SIMTEC_NOR + select MACH_BAST_IDE select ISA help Say Y here if you are using the Simtec Electronics EB2410ITX @@ -107,6 +121,8 @@ config MACH_TCT_HAMMER config MACH_VR1000 bool "Thorcom VR1000" select PM_SIMTEC if PM + select SIMTEC_NOR + select MACH_BAST_IDE select CPU_S3C2410 help Say Y here if you are using the Thorcom VR1000 board. @@ -118,4 +134,3 @@ config MACH_QT2410 Say Y here if you are using the Armzone QT2410 endmenu - diff --git a/arch/arm/mach-s3c2410/Makefile b/arch/arm/mach-s3c2410/Makefile index cabc13ce09e..00f31f8c4e7 100644 --- a/arch/arm/mach-s3c2410/Makefile +++ b/arch/arm/mach-s3c2410/Makefile @@ -30,3 +30,11 @@ obj-$(CONFIG_BAST_PC104_IRQ) += bast-irq.o obj-$(CONFIG_MACH_TCT_HAMMER) += mach-tct_hammer.o obj-$(CONFIG_MACH_VR1000) += mach-vr1000.o usb-simtec.o obj-$(CONFIG_MACH_QT2410) += mach-qt2410.o + +# Common bits of machine support + +obj-$(CONFIG_SIMTEC_NOR) += nor-simtec.o + +# machine additions + +obj-$(CONFIG_MACH_BAST_IDE) += bast-ide.o diff --git a/arch/arm/mach-s3c2410/bast-ide.c b/arch/arm/mach-s3c2410/bast-ide.c new file mode 100644 index 00000000000..df95fe37cdc --- /dev/null +++ b/arch/arm/mach-s3c2410/bast-ide.c @@ -0,0 +1,112 @@ +/* linux/arch/arm/mach-s3c2410/bast-ide.c + * + * Copyright 2007 Simtec Electronics + * http://www.simtec.co.uk/products/EB2410ITX/ + * http://armlinux.simtec.co.uk/ + * Ben Dooks <ben@simtec.co.uk> + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. +*/ + +#include <linux/kernel.h> +#include <linux/types.h> +#include <linux/init.h> +#include <linux/interrupt.h> + +#include <linux/platform_device.h> +#include <linux/ata_platform.h> + +#include <asm/mach-types.h> + +#include <asm/mach/arch.h> +#include <asm/mach/map.h> +#include <asm/mach/irq.h> + +#include <asm/arch/map.h> +#include <asm/arch/bast-map.h> +#include <asm/arch/bast-irq.h> + +/* IDE ports */ + +static struct pata_platform_info bast_ide_platdata = { + .ioport_shift = 5, +}; + +#define IDE_CS S3C2410_CS5 + +static struct resource bast_ide0_resource[] = { + [0] = { + .start = IDE_CS + BAST_PA_IDEPRI, + .end = IDE_CS + BAST_PA_IDEPRI + (8 * 0x20) - 1, + .flags = IORESOURCE_MEM, + }, + [1] = { + .start = IDE_CS + BAST_PA_IDEPRIAUX + (6 * 0x20) , + .end = IDE_CS + BAST_PA_IDEPRIAUX + (7 * 0x20) - 1, + .flags = IORESOURCE_MEM, + }, + [2] = { + .start = IRQ_IDE0, + .end = IRQ_IDE0, + .flags = IORESOURCE_IRQ, + }, +}; + +static struct platform_device bast_device_ide0 = { + .name = "pata_platform", + .id = 0, + .num_resources = ARRAY_SIZE(bast_ide0_resource), + .resource = bast_ide0_resource, + .dev = { + .platform_data = &bast_ide_platdata, + .coherent_dma_mask = ~0, + } + +}; + +static struct resource bast_ide1_resource[] = { + [0] = { + .start = IDE_CS + BAST_PA_IDESEC, + .end = IDE_CS + BAST_PA_IDESEC + (8 * 0x20) - 1, + .flags = IORESOURCE_MEM, + }, + [1] = { + .start = IDE_CS + BAST_PA_IDESECAUX + (6 * 0x20), + .end = IDE_CS + BAST_PA_IDESECAUX + (7 * 0x20) - 1, + .flags = IORESOURCE_MEM, + }, + [2] = { + .start = IRQ_IDE1, + .end = IRQ_IDE1, + .flags = IORESOURCE_IRQ, + }, +}; + +static struct platform_device bast_device_ide1 = { + .name = "pata_platform", + .id = 1, + .num_resources = ARRAY_SIZE(bast_ide1_resource), + .resource = bast_ide1_resource, + .dev = { + .platform_data = &bast_ide_platdata, + .coherent_dma_mask = ~0, + } +}; + +static struct platform_device *bast_ide_devices[] __initdata = { + &bast_device_ide0, + &bast_device_ide1, +}; + +static __init int bast_ide_init(void) +{ + if (machine_is_bast() || machine_is_vr1000()) + return platform_add_devices(bast_ide_devices, + ARRAY_SIZE(bast_ide_devices)); + + return 0; +} + +fs_initcall(bast_ide_init); diff --git a/arch/arm/mach-s3c2410/mach-bast.c b/arch/arm/mach-s3c2410/mach-bast.c index 27f63d5d3a7..965f2712970 100644 --- a/arch/arm/mach-s3c2410/mach-bast.c +++ b/arch/arm/mach-s3c2410/mach-bast.c @@ -1,6 +1,6 @@ /* linux/arch/arm/mach-s3c2410/mach-bast.c * - * Copyright (c) 2003-2005 Simtec Electronics + * Copyright (c) 2003-2005,2008 Simtec Electronics * Ben Dooks <ben@simtec.co.uk> * * http://www.simtec.co.uk/products/EB2410ITX/ @@ -20,6 +20,8 @@ #include <linux/serial_core.h> #include <linux/platform_device.h> #include <linux/dm9000.h> +#include <linux/ata_platform.h> +#include <linux/i2c.h> #include <net/ax88796.h> @@ -56,7 +58,9 @@ #include <asm/plat-s3c24xx/clock.h> #include <asm/plat-s3c24xx/devs.h> #include <asm/plat-s3c24xx/cpu.h> + #include "usb-simtec.h" +#include "nor-simtec.h" #define COPYRIGHT ", (c) 2004-2005 Simtec Electronics" @@ -134,37 +138,21 @@ static struct map_desc bast_iodesc[] __initdata = { { VA_C2(BAST_VA_ISAIO), PA_CS2(BAST_PA_ISAIO), SZ_16M, MT_DEVICE }, { VA_C2(BAST_VA_ISAMEM), PA_CS2(BAST_PA_ISAMEM), SZ_16M, MT_DEVICE }, { VA_C2(BAST_VA_SUPERIO), PA_CS2(BAST_PA_SUPERIO), SZ_1M, MT_DEVICE }, - { VA_C2(BAST_VA_IDEPRI), PA_CS3(BAST_PA_IDEPRI), SZ_1M, MT_DEVICE }, - { VA_C2(BAST_VA_IDESEC), PA_CS3(BAST_PA_IDESEC), SZ_1M, MT_DEVICE }, - { VA_C2(BAST_VA_IDEPRIAUX), PA_CS3(BAST_PA_IDEPRIAUX), SZ_1M, MT_DEVICE }, - { VA_C2(BAST_VA_IDESECAUX), PA_CS3(BAST_PA_IDESECAUX), SZ_1M, MT_DEVICE }, /* slow, word */ { VA_C3(BAST_VA_ISAIO), PA_CS3(BAST_PA_ISAIO), SZ_16M, MT_DEVICE }, { VA_C3(BAST_VA_ISAMEM), PA_CS3(BAST_PA_ISAMEM), SZ_16M, MT_DEVICE }, { VA_C3(BAST_VA_SUPERIO), PA_CS3(BAST_PA_SUPERIO), SZ_1M, MT_DEVICE }, - { VA_C3(BAST_VA_IDEPRI), PA_CS3(BAST_PA_IDEPRI), SZ_1M, MT_DEVICE }, - { VA_C3(BAST_VA_IDESEC), PA_CS3(BAST_PA_IDESEC), SZ_1M, MT_DEVICE }, - { VA_C3(BAST_VA_IDEPRIAUX), PA_CS3(BAST_PA_IDEPRIAUX), SZ_1M, MT_DEVICE }, - { VA_C3(BAST_VA_IDESECAUX), PA_CS3(BAST_PA_IDESECAUX), SZ_1M, MT_DEVICE }, /* fast, byte */ { VA_C4(BAST_VA_ISAIO), PA_CS4(BAST_PA_ISAIO), SZ_16M, MT_DEVICE }, { VA_C4(BAST_VA_ISAMEM), PA_CS4(BAST_PA_ISAMEM), SZ_16M, MT_DEVICE }, { VA_C4(BAST_VA_SUPERIO), PA_CS4(BAST_PA_SUPERIO), SZ_1M, MT_DEVICE }, - { VA_C4(BAST_VA_IDEPRI), PA_CS5(BAST_PA_IDEPRI), SZ_1M, MT_DEVICE }, - { VA_C4(BAST_VA_IDESEC), PA_CS5(BAST_PA_IDESEC), SZ_1M, MT_DEVICE }, - { VA_C4(BAST_VA_IDEPRIAUX), PA_CS5(BAST_PA_IDEPRIAUX), SZ_1M, MT_DEVICE }, - { VA_C4(BAST_VA_IDESECAUX), PA_CS5(BAST_PA_IDESECAUX), SZ_1M, MT_DEVICE }, /* fast, word */ { VA_C5(BAST_VA_ISAIO), PA_CS5(BAST_PA_ISAIO), SZ_16M, MT_DEVICE }, { VA_C5(BAST_VA_ISAMEM), PA_CS5(BAST_PA_ISAMEM), SZ_16M, MT_DEVICE }, { VA_C5(BAST_VA_SUPERIO), PA_CS5(BAST_PA_SUPERIO), SZ_1M, MT_DEVICE }, - { VA_C5(BAST_VA_IDEPRI), PA_CS5(BAST_PA_IDEPRI), SZ_1M, MT_DEVICE }, - { VA_C5(BAST_VA_IDESEC), PA_CS5(BAST_PA_IDESEC), SZ_1M, MT_DEVICE }, - { VA_C5(BAST_VA_IDEPRIAUX), PA_CS5(BAST_PA_IDEPRIAUX), SZ_1M, MT_DEVICE }, - { VA_C5(BAST_VA_IDESECAUX), PA_CS5(BAST_PA_IDESECAUX), SZ_1M, MT_DEVICE }, }; #define UCON S3C2410_UCON_DEFAULT | S3C2410_UCON_UCLK @@ -218,23 +206,6 @@ static struct s3c2410_uartcfg bast_uartcfgs[] __initdata = { } }; -/* NOR Flash on BAST board */ - -static struct resource bast_nor_resource[] = { - [0] = { - .start = S3C2410_CS1 + 0x4000000, - .end = S3C2410_CS1 + 0x4000000 + (32*1024*1024) - 1, - .flags = IORESOURCE_MEM, - } -}; - -static struct platform_device bast_device_nor = { - .name = "bast-nor", - .id = -1, - .num_resources = ARRAY_SIZE(bast_nor_resource), - .resource = bast_nor_resource, -}; - /* NAND Flash on BAST board */ #ifdef CONFIG_PM @@ -374,7 +345,7 @@ static struct resource bast_dm9k_resource[] = { [2] = { .start = IRQ_DM9000, .end = IRQ_DM9000, - .flags = IORESOURCE_IRQ | IRQF_TRIGGER_HIGH, + .flags = IORESOURCE_IRQ | IORESOURCE_IRQ_HIGHLEVEL, } }; @@ -564,6 +535,18 @@ static struct s3c2410fb_mach_info __initdata bast_fb_info = { .default_display = 1, }; +/* I2C devices fitted. */ + +static struct i2c_board_info bast_i2c_devs[] __initdata = { + { + I2C_BOARD_INFO("tlv320aic23", 0x1a), + }, { + I2C_BOARD_INFO("simtec-pmu", 0x6b), + }, { + I2C_BOARD_INFO("ch7013", 0x75), + }, +}; + /* Standard BAST devices */ static struct platform_device *bast_devices[] __initdata = { @@ -573,7 +556,6 @@ static struct platform_device *bast_devices[] __initdata = { &s3c_device_i2c, &s3c_device_rtc, &s3c_device_nand, - &bast_device_nor, &bast_device_dm9k, &bast_device_asix, &bast_device_axpp, @@ -622,6 +604,11 @@ static void __init bast_init(void) s3c24xx_fb_set_platdata(&bast_fb_info); platform_add_devices(bast_devices, ARRAY_SIZE(bast_devices)); + + i2c_register_board_info(0, bast_i2c_devs, + ARRAY_SIZE(bast_i2c_devs)); + + nor_simtec_init(); } MACHINE_START(BAST, "Simtec-BAST") diff --git a/arch/arm/mach-s3c2410/mach-n30.c b/arch/arm/mach-s3c2410/mach-n30.c index 621f548da61..43c2e915c5b 100644 --- a/arch/arm/mach-s3c2410/mach-n30.c +++ b/arch/arm/mach-s3c2410/mach-n30.c @@ -1,9 +1,10 @@ -/* linux/arch/arm/mach-s3c2410/mach-n30.c +/* Machine specific code for the Acer n30, Acer N35, Navman PiN 570, + * Yakumo AlphaX and Airis NC05 PDAs. * * Copyright (c) 2003-2005 Simtec Electronics * Ben Dooks <ben@simtec.co.uk> * - * Copyright (c) 2005 Christer Weinigel <christer@weinigel.se> + * Copyright (c) 2005-2008 Christer Weinigel <christer@weinigel.se> * * There is a wiki with more information about the n30 port at * http://handhelds.org/moin/moin.cgi/AcerN30Documentation . @@ -11,36 +12,42 @@ * This program is free software; you can redistribute it and/or modify * it under the terms of the GNU General Public License version 2 as * published by the Free Software Foundation. -*/ + */ #include <linux/kernel.h> #include <linux/types.h> -#include <linux/interrupt.h> -#include <linux/list.h> -#include <linux/timer.h> -#include <linux/init.h> + #include <linux/delay.h> -#include <linux/serial_core.h> +#include <linux/gpio_keys.h> +#include <linux/init.h> +#include <linux/input.h> +#include <linux/interrupt.h> #include <linux/platform_device.h> -#include <linux/kthread.h> - -#include <asm/mach/arch.h> -#include <asm/mach/map.h> -#include <asm/mach/irq.h> +#include <linux/serial_core.h> +#include <linux/timer.h> #include <asm/hardware.h> #include <asm/io.h> #include <asm/irq.h> #include <asm/mach-types.h> -#include <asm/plat-s3c/regs-serial.h> +#include <asm/arch/fb.h> +#include <asm/arch/leds-gpio.h> #include <asm/arch/regs-gpio.h> +#include <asm/arch/regs-lcd.h> + +#include <asm/mach/arch.h> +#include <asm/mach/irq.h> +#include <asm/mach/map.h> + #include <asm/plat-s3c/iic.h> +#include <asm/plat-s3c/regs-serial.h> -#include <asm/plat-s3c24xx/s3c2410.h> #include <asm/plat-s3c24xx/clock.h> -#include <asm/plat-s3c24xx/devs.h> #include <asm/plat-s3c24xx/cpu.h> +#include <asm/plat-s3c24xx/devs.h> +#include <asm/plat-s3c24xx/s3c2410.h> +#include <asm/plat-s3c24xx/udc.h> static struct map_desc n30_iodesc[] __initdata = { /* nothing here yet */ @@ -64,7 +71,8 @@ static struct s3c2410_uartcfg n30_uartcfgs[] = { .ulcon = 0x43, .ufcon = 0x51, }, - /* The BlueTooth controller is connected to port 2 */ + /* On the N30 the bluetooth controller is connected here. + * On the N35 and variants the GPS receiver is connected here. */ [2] = { .hwport = 2, .flags = 0, @@ -74,13 +82,260 @@ static struct s3c2410_uartcfg n30_uartcfgs[] = { }, }; +static void n30_udc_pullup(enum s3c2410_udc_cmd_e cmd) +{ + switch (cmd) { + case S3C2410_UDC_P_ENABLE : + s3c2410_gpio_setpin(S3C2410_GPB3, 1); + break; + case S3C2410_UDC_P_DISABLE : + s3c2410_gpio_setpin(S3C2410_GPB3, 0); + break; + case S3C2410_UDC_P_RESET : + break; + default: + break; + } +} + +static struct s3c2410_udc_mach_info n30_udc_cfg __initdata = { + .udc_command = n30_udc_pullup, + .vbus_pin = S3C2410_GPG1, + .vbus_pin_inverted = 0, +}; + +static struct gpio_keys_button n30_buttons[] = { + { + .gpio = S3C2410_GPF0, + .code = KEY_POWER, + .desc = "Power", + .active_low = 0, + }, + { + .gpio = S3C2410_GPG9, + .code = KEY_UP, + .desc = "Thumbwheel Up", + .active_low = 0, + }, + { + .gpio = S3C2410_GPG8, + .code = KEY_DOWN, + .desc = "Thumbwheel Down", + .active_low = 0, + }, + { + .gpio = S3C2410_GPG7, + .code = KEY_ENTER, + .desc = "Thumbwheel Press", + .active_low = 0, + }, + { + .gpio = S3C2410_GPF7, + .code = KEY_HOMEPAGE, + .desc = "Home", + .active_low = 0, + }, + { + .gpio = S3C2410_GPF6, + .code = KEY_CALENDAR, + .desc = "Calendar", + .active_low = 0, + }, + { + .gpio = S3C2410_GPF5, + .code = KEY_ADDRESSBOOK, + .desc = "Contacts", + .active_low = 0, + }, + { + .gpio = S3C2410_GPF4, + .code = KEY_MAIL, + .desc = "Mail", + .active_low = 0, + }, +}; + +static struct gpio_keys_platform_data n30_button_data = { + .buttons = n30_buttons, + .nbuttons = ARRAY_SIZE(n30_buttons), +}; + +static struct platform_device n30_button_device = { + .name = "gpio-keys", + .id = -1, + .dev = { + .platform_data = &n30_button_data, + } +}; + +static struct gpio_keys_button n35_buttons[] = { + { + .gpio = S3C2410_GPF0, + .code = KEY_POWER, + .desc = "Power", + .active_low = 0, + }, + { + .gpio = S3C2410_GPG9, + .code = KEY_UP, + .desc = "Joystick Up", + .active_low = 0, + }, + { + .gpio = S3C2410_GPG8, + .code = KEY_DOWN, + .desc = "Joystick Down", + .active_low = 0, + }, + { + .gpio = S3C2410_GPG6, + .code = KEY_DOWN, + .desc = "Joystick Left", + .active_low = 0, + }, + { + .gpio = S3C2410_GPG5, + .code = KEY_DOWN, + .desc = "Joystick Right", + .active_low = 0, + }, + { + .gpio = S3C2410_GPG7, + .code = KEY_ENTER, + .desc = "Joystick Press", + .active_low = 0, + }, + { + .gpio = S3C2410_GPF7, + .code = KEY_HOMEPAGE, + .desc = "Home", + .active_low = 0, + }, + { + .gpio = S3C2410_GPF6, + .code = KEY_CALENDAR, + .desc = "Calendar", + .active_low = 0, + }, + { + .gpio = S3C2410_GPF5, + .code = KEY_ADDRESSBOOK, + .desc = "Contacts", + .active_low = 0, + }, + { + .gpio = S3C2410_GPF4, + .code = KEY_MAIL, + .desc = "Mail", + .active_low = 0, + }, + { + .gpio = S3C2410_GPF3, + .code = SW_RADIO, + .desc = "GPS Antenna", + .active_low = 0, + }, + { + .gpio = S3C2410_GPG2, + .code = SW_HEADPHONE_INSERT, + .desc = "Headphone", + .active_low = 0, + }, +}; + +static struct gpio_keys_platform_data n35_button_data = { + .buttons = n35_buttons, + .nbuttons = ARRAY_SIZE(n35_buttons), +}; + +static struct platform_device n35_button_device = { + .name = "gpio-keys", + .id = -1, + .num_resources = 0, + .dev = { + .platform_data = &n35_button_data, + } +}; + +/* This is the bluetooth LED on the device. */ +static struct s3c24xx_led_platdata n30_blue_led_pdata = { + .name = "blue_led", + .gpio = S3C2410_GPG6, + .def_trigger = "", +}; + +/* This LED is driven by the battery microcontroller, and is blinking + * red, blinking green or solid green when the battery is low, + * charging or full respectively. By driving GPD9 low, it's possible + * to force the LED to blink red, so call that warning LED. */ +static struct s3c24xx_led_platdata n30_warning_led_pdata = { + .name = "warning_led", + .flags = S3C24XX_LEDF_ACTLOW, + .gpio = S3C2410_GPD9, + .def_trigger = "", +}; + +static struct platform_device n30_blue_led = { + .name = "s3c24xx_led", + .id = 1, + .dev = { + .platform_data = &n30_blue_led_pdata, + }, +}; + +static struct platform_device n30_warning_led = { + .name = "s3c24xx_led", + .id = 2, + .dev = { + .platform_data = &n30_warning_led_pdata, + }, +}; + +static struct s3c2410fb_display n30_display __initdata = { + .type = S3C2410_LCDCON1_TFT, + .width = 240, + .height = 320, + .pixclock = 170000, + + .xres = 240, + .yres = 320, + .bpp = 16, + .left_margin = 3, + .right_margin = 40, + .hsync_len = 40, + .upper_margin = 2, + .lower_margin = 3, + .vsync_len = 2, + + .lcdcon5 = S3C2410_LCDCON5_INVVLINE | S3C2410_LCDCON5_INVVFRAME, +}; + +static struct s3c2410fb_mach_info n30_fb_info __initdata = { + .displays = &n30_display, + .num_displays = 1, + .default_display = 0, + .lpcsel = 0x06, +}; + static struct platform_device *n30_devices[] __initdata = { + &s3c_device_lcd, + &s3c_device_wdt, + &s3c_device_i2c, + &s3c_device_iis, &s3c_device_usb, + &s3c_device_usbgadget, + &n30_button_device, + &n30_blue_led, + &n30_warning_led, +}; + +static struct platform_device *n35_devices[] __initdata = { &s3c_device_lcd, &s3c_device_wdt, &s3c_device_i2c, &s3c_device_iis, &s3c_device_usbgadget, + &n35_button_device, }; static struct s3c2410_platform_i2c n30_i2ccfg = { @@ -90,9 +345,148 @@ static struct s3c2410_platform_i2c n30_i2ccfg = { .max_freq = 10*1000, }; +/* Lots of hardcoded stuff, but it sets up the hardware in a useful + * state so that we can boot Linux directly from flash. */ +static void __init n30_hwinit(void) +{ + /* GPA0-11 special functions -- unknown what they do + * GPA12 N30 special function -- unknown what it does + * N35/PiN output -- unknown what it does + * + * A12 is nGCS1 on the N30 and an output on the N35/PiN. I + * don't think it does anything useful on the N30, so I ought + * to make it an output there too since it always driven to 0 + * as far as I can tell. */ + if (machine_is_n30()) + __raw_writel(0x007fffff, S3C2410_GPACON); + if (machine_is_n35()) + __raw_writel(0x007fefff, S3C2410_GPACON); + __raw_writel(0x00000000, S3C2410_GPADAT); + + /* GPB0 TOUT0 backlight level + * GPB1 output 1=backlight on + * GPB2 output IrDA enable 0=transceiver enabled, 1=disabled + * GPB3 output USB D+ pull up 0=disabled, 1=enabled + * GPB4 N30 output -- unknown function + * N30/PiN GPS control 0=GPS enabled, 1=GPS disabled + * GPB5 output -- unknown function + * GPB6 input -- unknown function + * GPB7 output -- unknown function + * GPB8 output -- probably LCD driver enable + * GPB9 output -- probably LCD VSYNC driver enable + * GPB10 output -- probably LCD HSYNC driver enable + */ + __raw_writel(0x00154556, S3C2410_GPBCON); + __raw_writel(0x00000750, S3C2410_GPBDAT); + __raw_writel(0x00000073, S3C2410_GPBUP); + + /* GPC0 input RS232 DCD/DSR/RI + * GPC1 LCD + * GPC2 output RS232 DTR? + * GPC3 input RS232 DCD/DSR/RI + * GPC4 LCD + * GPC5 output 0=NAND write enabled, 1=NAND write protect + * GPC6 input -- unknown function + * GPC7 input charger status 0=charger connected + * this input can be triggered by power on the USB device + * port too, but will go back to disconnected soon after. + * GPC8 N30/N35 output -- unknown function, always driven to 1 + * PiN input -- unknown function, always read as 1 + * Make it an input with a pull up for all models. + * GPC9-15 LCD + */ + __raw_writel(0xaaa80618, S3C2410_GPCCON); + __raw_writel(0x0000014c, S3C2410_GPCDAT); + __raw_writel(0x0000fef2, S3C2410_GPCUP); + + /* GPD0 input -- unknown function + * GPD1-D7 LCD + * GPD8 N30 output -- unknown function + * N35/PiN output 1=GPS LED on + * GPD9 output 0=power led blinks red, 1=normal power led function + * GPD10 output -- unknown function + * GPD11-15 LCD drivers + */ + __raw_writel(0xaa95aaa4, S3C2410_GPDCON); + __raw_writel(0x00000601, S3C2410_GPDDAT); + __raw_writel(0x0000fbfe, S3C2410_GPDUP); + + /* GPE0-4 I2S audio bus + * GPE5-10 SD/MMC bus + * E11-13 outputs -- unknown function, probably power management + * E14-15 I2C bus connected to the battery controller + */ + __raw_writel(0xa56aaaaa, S3C2410_GPECON); + __raw_writel(0x0000efc5, S3C2410_GPEDAT); + __raw_writel(0x0000f81f, S3C2410_GPEUP); + + /* GPF0 input 0=power button pressed + * GPF1 input SD/MMC switch 0=card present + * GPF2 N30 1=reset button pressed (inverted compared to the rest) + * N35/PiN 0=reset button pressed + * GPF3 N30/PiN input -- unknown function + * N35 input GPS antenna position, 0=antenna closed, 1=open + * GPF4 input 0=button 4 pressed + * GPF5 input 0=button 3 pressed + * GPF6 input 0=button 2 pressed + * GPF7 input 0=button 1 pressed + */ + __raw_writel(0x0000aaaa, S3C2410_GPFCON); + __raw_writel(0x00000000, S3C2410_GPFDAT); + __raw_writel(0x000000ff, S3C2410_GPFUP); + + /* GPG0 input RS232 DCD/DSR/RI + * GPG1 input 1=USB gadget port has power from a host + * GPG2 N30 input -- unknown function + * N35/PiN input 0=headphones plugged in, 1=not plugged in + * GPG3 N30 output -- unknown function + * N35/PiN input with unknown function + * GPG4 N30 output 0=MMC enabled, 1=MMC disabled + * GPG5 N30 output 0=BlueTooth chip disabled, 1=enabled + * N35/PiN input joystick right + * GPG6 N30 output 0=blue led on, 1=off + * N35/PiN input joystick left + * GPG7 input 0=thumbwheel pressed + * GPG8 input 0=thumbwheel down + * GPG9 input 0=thumbwheel up + * GPG10 input SD/MMC write protect switch + * GPG11 N30 input -- unknown function + * N35 output 0=GPS antenna powered, 1=not powered + * PiN output -- unknown function + * GPG12-15 touch screen functions + * + * The pullups differ between the models, so enable all + * pullups that are enabled on any of the models. + */ + if (machine_is_n30()) + __raw_writel(0xff0a956a, S3C2410_GPGCON); + if (machine_is_n35()) + __raw_writel(0xff4aa92a, S3C2410_GPGCON); + __raw_writel(0x0000e800, S3C2410_GPGDAT); + __raw_writel(0x0000f86f, S3C2410_GPGUP); + + /* GPH0/1/2/3 RS232 serial port + * GPH4/5 IrDA serial port + * GPH6/7 N30 BlueTooth serial port + * N35/PiN GPS receiver + * GPH8 input -- unknown function + * GPH9 CLKOUT0 HCLK -- unknown use + * GPH10 CLKOUT1 FCLK -- unknown use + * + * The pull ups for H6/H7 are enabled on N30 but not on the + * N35/PiN. I suppose is useful for a budget model of the N30 + * with no bluetooh. It doesn't hurt to have the pull ups + * enabled on the N35, so leave them enabled for all models. + */ + __raw_writel(0x0028aaaa, S3C2410_GPHCON); + __raw_writel(0x000005ef, S3C2410_GPHDAT); + __raw_writel(0x0000063f, S3C2410_GPHUP); +} + static void __init n30_map_io(void) { s3c24xx_init_io(n30_iodesc, ARRAY_SIZE(n30_iodesc)); + n30_hwinit(); s3c24xx_init_clocks(0); s3c24xx_init_uarts(n30_uartcfgs, ARRAY_SIZE(n30_uartcfgs)); } @@ -106,7 +500,9 @@ static void __init n30_init_irq(void) static void __init n30_init(void) { + s3c24xx_fb_set_platdata(&n30_fb_info); s3c_device_i2c.dev.platform_data = &n30_i2ccfg; + s3c24xx_udc_set_platdata(&n30_udc_cfg); /* Turn off suspend on both USB ports, and switch the * selectable USB port to USB device mode. */ @@ -115,7 +511,32 @@ static void __init n30_init(void) S3C2410_MISCCR_USBSUSPND0 | S3C2410_MISCCR_USBSUSPND1, 0x0); - platform_add_devices(n30_devices, ARRAY_SIZE(n30_devices)); + if (machine_is_n30()) { + /* Turn off suspend on both USB ports, and switch the + * selectable USB port to USB device mode. */ + s3c2410_modify_misccr(S3C2410_MISCCR_USBHOST | + S3C2410_MISCCR_USBSUSPND0 | + S3C2410_MISCCR_USBSUSPND1, 0x0); + + platform_add_devices(n30_devices, ARRAY_SIZE(n30_devices)); + } + + if (machine_is_n35()) { + /* Turn off suspend and switch the selectable USB port + * to USB device mode. Turn on suspend for the host + * port since it is not connected on the N35. + * + * Actually, the host port is available at some pads + * on the back of the device, so it would actually be + * possible to add a USB device inside the N35 if you + * are willing to do some hardware modifications. */ + s3c2410_modify_misccr(S3C2410_MISCCR_USBHOST | + S3C2410_MISCCR_USBSUSPND0 | + S3C2410_MISCCR_USBSUSPND1, + S3C2410_MISCCR_USBSUSPND1); + + platform_add_devices(n35_devices, ARRAY_SIZE(n35_devices)); + } } MACHINE_START(N30, "Acer-N30") @@ -131,9 +552,14 @@ MACHINE_START(N30, "Acer-N30") .map_io = n30_map_io, MACHINE_END -/* - Local variables: - compile-command: "make ARCH=arm CROSS_COMPILE=/usr/local/arm/3.3.2/bin/arm-linux- -k -C ../../.." - c-basic-offset: 8 - End: -*/ +MACHINE_START(N35, "Acer-N35") + /* Maintainer: Christer Weinigel <christer@weinigel.se> + */ + .phys_io = S3C2410_PA_UART, + .io_pg_offst = (((u32)S3C24XX_VA_UART) >> 18) & 0xfffc, + .boot_params = S3C2410_SDRAM_PA + 0x100, + .timer = &s3c24xx_timer, + .init_machine = n30_init, + .init_irq = n30_init_irq, + .map_io = n30_map_io, +MACHINE_END diff --git a/arch/arm/mach-s3c2410/mach-vr1000.c b/arch/arm/mach-s3c2410/mach-vr1000.c index 4c4b5c4207c..9a0965ac5e1 100644 --- a/arch/arm/mach-s3c2410/mach-vr1000.c +++ b/arch/arm/mach-s3c2410/mach-vr1000.c @@ -1,6 +1,6 @@ /* linux/arch/arm/mach-s3c2410/mach-vr1000.c * - * Copyright (c) 2003-2005 Simtec Electronics + * Copyright (c) 2003-2005,2008 Simtec Electronics * Ben Dooks <ben@simtec.co.uk> * * Machine support for Thorcom VR1000 board. Designed for Thorcom by @@ -19,6 +19,7 @@ #include <linux/timer.h> #include <linux/init.h> #include <linux/dm9000.h> +#include <linux/i2c.h> #include <linux/serial.h> #include <linux/tty.h> @@ -46,7 +47,9 @@ #include <asm/plat-s3c24xx/clock.h> #include <asm/plat-s3c24xx/devs.h> #include <asm/plat-s3c24xx/cpu.h> + #include "usb-simtec.h" +#include "nor-simtec.h" /* macros for virtual address mods for the io space entries */ #define VA_C5(item) ((unsigned long)(item) + BAST_VAM_CS5) @@ -97,34 +100,6 @@ static struct map_desc vr1000_iodesc[] __initdata = { .length = SZ_1M, .type = MT_DEVICE, }, - - /* peripheral space... one for each of fast/slow/byte/16bit */ - /* note, ide is only decoded in word space, even though some registers - * are only 8bit */ - - /* slow, byte */ - { VA_C2(VR1000_VA_IDEPRI), PA_CS3(VR1000_PA_IDEPRI), SZ_1M, MT_DEVICE }, - { VA_C2(VR1000_VA_IDESEC), PA_CS3(VR1000_PA_IDESEC), SZ_1M, MT_DEVICE }, - { VA_C2(VR1000_VA_IDEPRIAUX), PA_CS3(VR1000_PA_IDEPRIAUX), SZ_1M, MT_DEVICE }, - { VA_C2(VR1000_VA_IDESECAUX), PA_CS3(VR1000_PA_IDESECAUX), SZ_1M, MT_DEVICE }, - - /* slow, word */ - { VA_C3(VR1000_VA_IDEPRI), PA_CS3(VR1000_PA_IDEPRI), SZ_1M, MT_DEVICE }, - { VA_C3(VR1000_VA_IDESEC), PA_CS3(VR1000_PA_IDESEC), SZ_1M, MT_DEVICE }, - { VA_C3(VR1000_VA_IDEPRIAUX), PA_CS3(VR1000_PA_IDEPRIAUX), SZ_1M, MT_DEVICE }, - { VA_C3(VR1000_VA_IDESECAUX), PA_CS3(VR1000_PA_IDESECAUX), SZ_1M, MT_DEVICE }, - - /* fast, byte */ - { VA_C4(VR1000_VA_IDEPRI), PA_CS5(VR1000_PA_IDEPRI), SZ_1M, MT_DEVICE }, - { VA_C4(VR1000_VA_IDESEC), PA_CS5(VR1000_PA_IDESEC), SZ_1M, MT_DEVICE }, - { VA_C4(VR1000_VA_IDEPRIAUX), PA_CS5(VR1000_PA_IDEPRIAUX), SZ_1M, MT_DEVICE }, - { VA_C4(VR1000_VA_IDESECAUX), PA_CS5(VR1000_PA_IDESECAUX), SZ_1M, MT_DEVICE }, - - /* fast, word */ - { VA_C5(VR1000_VA_IDEPRI), PA_CS5(VR1000_PA_IDEPRI), SZ_1M, MT_DEVICE }, - { VA_C5(VR1000_VA_IDESEC), PA_CS5(VR1000_PA_IDESEC), SZ_1M, MT_DEVICE }, - { VA_C5(VR1000_VA_IDEPRIAUX), PA_CS5(VR1000_PA_IDEPRIAUX), SZ_1M, MT_DEVICE }, - { VA_C5(VR1000_VA_IDESECAUX), PA_CS5(VR1000_PA_IDESECAUX), SZ_1M, MT_DEVICE }, }; #define UCON S3C2410_UCON_DEFAULT | S3C2410_UCON_UCLK @@ -230,23 +205,6 @@ static struct platform_device serial_device = { }, }; -/* MTD NOR Flash */ - -static struct resource vr1000_nor_resource[] = { - [0] = { - .start = S3C2410_CS1 + 0x4000000, - .end = S3C2410_CS1 + 0x4000000 + SZ_16M - 1, - .flags = IORESOURCE_MEM, - } -}; - -static struct platform_device vr1000_nor = { - .name = "bast-nor", - .id = -1, - .num_resources = ARRAY_SIZE(vr1000_nor_resource), - .resource = vr1000_nor_resource, -}; - /* DM9000 ethernet devices */ static struct resource vr1000_dm9k0_resource[] = { @@ -263,7 +221,7 @@ static struct resource vr1000_dm9k0_resource[] = { [2] = { .start = IRQ_VR1000_DM9000A, .end = IRQ_VR1000_DM9000A, - .flags = IORESOURCE_IRQ | IRQF_TRIGGER_HIGH, + .flags = IORESOURCE_IRQ | IORESOURCE_IRQ_HIGHLEVEL, } }; @@ -282,7 +240,7 @@ static struct resource vr1000_dm9k1_resource[] = { [2] = { .start = IRQ_VR1000_DM9000N, .end = IRQ_VR1000_DM9000N, - .flags = IORESOURCE_IRQ | IRQF_TRIGGER_HIGH, + .flags = IORESOURCE_IRQ | IORESOURCE_IRQ_HIGHLEVEL, } }; @@ -358,6 +316,18 @@ static struct platform_device vr1000_led3 = { }, }; +/* I2C devices. */ + +static struct i2c_board_info vr1000_i2c_devs[] __initdata = { + { + I2C_BOARD_INFO("tlv320aic23", 0x1a), + }, { + I2C_BOARD_INFO("tmp101", 0x48), + }, { + I2C_BOARD_INFO("m41st87", 0x68), + }, +}; + /* devices for this board */ static struct platform_device *vr1000_devices[] __initdata = { @@ -367,7 +337,6 @@ static struct platform_device *vr1000_devices[] __initdata = { &s3c_device_i2c, &s3c_device_adc, &serial_device, - &vr1000_nor, &vr1000_dm9k0, &vr1000_dm9k1, &vr1000_led1, @@ -416,6 +385,11 @@ static void __init vr1000_map_io(void) static void __init vr1000_init(void) { platform_add_devices(vr1000_devices, ARRAY_SIZE(vr1000_devices)); + + i2c_register_board_info(0, vr1000_i2c_devs, + ARRAY_SIZE(vr1000_i2c_devs)); + + nor_simtec_init(); } MACHINE_START(VR1000, "Thorcom-VR1000") diff --git a/arch/arm/mach-s3c2410/nor-simtec.c b/arch/arm/mach-s3c2410/nor-simtec.c new file mode 100644 index 00000000000..f44e21b9c3b --- /dev/null +++ b/arch/arm/mach-s3c2410/nor-simtec.c @@ -0,0 +1,86 @@ +/* linux/arch/arm/mach-s3c2410/nor-simtec.c + * + * Copyright (c) 2008 Simtec Electronics + * http://armlinux.simtec.co.uk/ + * Ben Dooks <ben@simtec.co.uk> + * + * Simtec NOR mapping + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. +*/ + +#include <linux/module.h> +#include <linux/types.h> +#include <linux/init.h> +#include <linux/kernel.h> +#include <linux/platform_device.h> + +#include <linux/mtd/mtd.h> +#include <linux/mtd/map.h> +#include <linux/mtd/physmap.h> +#include <linux/mtd/partitions.h> + +#include <asm/mach/arch.h> +#include <asm/mach/map.h> +#include <asm/mach/irq.h> + +#include <asm/arch/map.h> +#include <asm/arch/bast-map.h> +#include <asm/arch/bast-cpld.h> + + +static void simtec_nor_vpp(struct map_info *map, int vpp) +{ + unsigned int val; + unsigned long flags; + + local_irq_save(flags); + val = __raw_readb(BAST_VA_CTRL3); + + printk(KERN_DEBUG "%s(%d)\n", __func__, vpp); + + if (vpp) + val |= BAST_CPLD_CTRL3_ROMWEN; + else + val &= ~BAST_CPLD_CTRL3_ROMWEN; + + __raw_writeb(val, BAST_VA_CTRL3); + local_irq_restore(flags); +} + +struct physmap_flash_data simtec_nor_pdata = { + .width = 2, + .set_vpp = simtec_nor_vpp, + .nr_parts = 0, +}; + +static struct resource simtec_nor_resource[] = { + [0] = { + .start = S3C2410_CS1 + 0x4000000, + .end = S3C2410_CS1 + 0x4000000 + SZ_8M - 1, + .flags = IORESOURCE_MEM, + } +}; + +static struct platform_device simtec_device_nor = { + .name = "physmap-flash", + .id = -1, + .num_resources = ARRAY_SIZE(simtec_nor_resource), + .resource = simtec_nor_resource, + .dev = { + .platform_data = &simtec_nor_pdata, + }, +}; + +void __init nor_simtec_init(void) +{ + int ret; + + ret = platform_device_register(&simtec_device_nor); + if (ret < 0) + printk(KERN_ERR "failed to register physmap-flash device\n"); + else + simtec_nor_vpp(NULL, 1); +} diff --git a/arch/arm/mach-s3c2410/nor-simtec.h b/arch/arm/mach-s3c2410/nor-simtec.h new file mode 100644 index 00000000000..f619c1e0d0c --- /dev/null +++ b/arch/arm/mach-s3c2410/nor-simtec.h @@ -0,0 +1,14 @@ +/* linux/arch/arm/mach-s3c2410/nor-simtec.h + * + * Copyright (c) 2008 Simtec Electronics + * http://armlinux.simtec.co.uk/ + * Ben Dooks <ben@simtec.co.uk> + * + * Simtec NOR mapping + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. +*/ + +extern void nor_simtec_init(void); diff --git a/arch/arm/mach-s3c2412/Kconfig b/arch/arm/mach-s3c2412/Kconfig index 0b43431d4b7..c59a9d2ee9a 100644 --- a/arch/arm/mach-s3c2412/Kconfig +++ b/arch/arm/mach-s3c2412/Kconfig @@ -34,6 +34,16 @@ config S3C2412_PM menu "S3C2412 Machines" +config MACH_JIVE + bool "Logitech Jive" + select CPU_S3C2412 + help + Say Y here if you are using the Logitech Jive. + +config MACH_JIVE_SHOW_BOOTLOADER + bool "Allow access to bootloader partitions in MTD" + depends on MACH_JIVE && EXPERIMENTAL + config MACH_SMDK2413 bool "SMDK2413" select CPU_S3C2412 diff --git a/arch/arm/mach-s3c2412/Makefile b/arch/arm/mach-s3c2412/Makefile index 267f3348301..20918d5dc6a 100644 --- a/arch/arm/mach-s3c2412/Makefile +++ b/arch/arm/mach-s3c2412/Makefile @@ -18,5 +18,6 @@ obj-$(CONFIG_S3C2412_PM) += pm.o sleep.o # Machine support +obj-$(CONFIG_MACH_JIVE) += mach-jive.o obj-$(CONFIG_MACH_SMDK2413) += mach-smdk2413.o obj-$(CONFIG_MACH_VSTMS) += mach-vstms.o diff --git a/arch/arm/mach-s3c2412/clock.c b/arch/arm/mach-s3c2412/clock.c index 2697a65ba72..1157b5a1626 100644 --- a/arch/arm/mach-s3c2412/clock.c +++ b/arch/arm/mach-s3c2412/clock.c @@ -631,6 +631,17 @@ static struct clk_init clks_src[] __initdata = { .bit = S3C2412_CLKSRC_USBCLK_HCLK, .src_0 = &clk_usysclk, .src_1 = &clk_h, + /* here we assume OM[4] select xtal */ + }, { + .clk = &clk_erefclk, + .bit = S3C2412_CLKSRC_EREFCLK_EXTCLK, + .src_0 = &clk_xtal, + .src_1 = &clk_ext, + }, { + .clk = &clk_urefclk, + .bit = S3C2412_CLKSRC_UREFCLK_EXTCLK, + .src_0 = &clk_xtal, + .src_1 = &clk_ext, }, }; @@ -666,8 +677,6 @@ static void __init s3c2412_clk_initparents(void) static struct clk *clks[] __initdata = { &clk_ext, &clk_usb_bus, - &clk_erefclk, - &clk_urefclk, &clk_mrefclk, &clk_armclk, }; diff --git a/arch/arm/mach-s3c2412/mach-jive.c b/arch/arm/mach-s3c2412/mach-jive.c new file mode 100644 index 00000000000..7f592471348 --- /dev/null +++ b/arch/arm/mach-s3c2412/mach-jive.c @@ -0,0 +1,687 @@ +/* linux/arch/arm/mach-s3c2410/mach-jive.c + * + * Copyright 2007 Simtec Electronics + * Ben Dooks <ben@simtec.co.uk> + * + * http://armlinux.simtec.co.uk/ + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. +*/ + +#include <linux/kernel.h> +#include <linux/types.h> +#include <linux/interrupt.h> +#include <linux/list.h> +#include <linux/timer.h> +#include <linux/init.h> +#include <linux/sysdev.h> +#include <linux/delay.h> +#include <linux/serial_core.h> +#include <linux/platform_device.h> +#include <linux/i2c.h> + +#include <video/ili9320.h> + +#include <linux/spi/spi.h> + +#include <linux/mtd/mtd.h> +#include <linux/mtd/partitions.h> + +#include <asm/mach/arch.h> +#include <asm/mach/map.h> +#include <asm/mach/irq.h> + +#include <asm/plat-s3c/regs-serial.h> +#include <asm/plat-s3c/nand.h> +#include <asm/plat-s3c/iic.h> + +#include <asm/arch/regs-power.h> +#include <asm/arch/regs-gpio.h> +#include <asm/arch/regs-mem.h> +#include <asm/arch/regs-lcd.h> +#include <asm/arch/spi-gpio.h> +#include <asm/arch/fb.h> + +#include <asm/mach-types.h> + +#include <linux/mtd/mtd.h> +#include <linux/mtd/nand.h> +#include <linux/mtd/nand_ecc.h> +#include <linux/mtd/partitions.h> + +#include <asm/plat-s3c24xx/clock.h> +#include <asm/plat-s3c24xx/devs.h> +#include <asm/plat-s3c24xx/cpu.h> +#include <asm/plat-s3c24xx/pm.h> +#include <asm/plat-s3c24xx/udc.h> + +static struct map_desc jive_iodesc[] __initdata = { +}; + +#define UCON S3C2410_UCON_DEFAULT +#define ULCON S3C2410_LCON_CS8 | S3C2410_LCON_PNONE +#define UFCON S3C2410_UFCON_RXTRIG8 | S3C2410_UFCON_FIFOMODE + +static struct s3c2410_uartcfg jive_uartcfgs[] = { + [0] = { + .hwport = 0, + .flags = 0, + .ucon = UCON, + .ulcon = ULCON, + .ufcon = UFCON, + }, + [1] = { + .hwport = 1, + .flags = 0, + .ucon = UCON, + .ulcon = ULCON, + .ufcon = UFCON, + }, + [2] = { + .hwport = 2, + .flags = 0, + .ucon = UCON, + .ulcon = ULCON, + .ufcon = UFCON, + } +}; + +/* Jive flash assignment + * + * 0x00000000-0x00028000 : uboot + * 0x00028000-0x0002c000 : uboot env + * 0x0002c000-0x00030000 : spare + * 0x00030000-0x00200000 : zimage A + * 0x00200000-0x01600000 : cramfs A + * 0x01600000-0x017d0000 : zimage B + * 0x017d0000-0x02bd0000 : cramfs B + * 0x02bd0000-0x03fd0000 : yaffs + */ +static struct mtd_partition jive_imageA_nand_part[] = { + +#ifdef CONFIG_MACH_JIVE_SHOW_BOOTLOADER + /* Don't allow access to the bootloader from linux */ + { + .name = "uboot", + .offset = 0, + .size = (160 * SZ_1K), + .mask_flags = MTD_WRITEABLE, /* force read-only */ + }, + + /* spare */ + { + .name = "spare", + .offset = (176 * SZ_1K), + .size = (16 * SZ_1K), + }, +#endif + + /* booted images */ + { + .name = "kernel (ro)", + .offset = (192 * SZ_1K), + .size = (SZ_2M) - (192 * SZ_1K), + .mask_flags = MTD_WRITEABLE, /* force read-only */ + }, { + .name = "root (ro)", + .offset = (SZ_2M), + .size = (20 * SZ_1M), + .mask_flags = MTD_WRITEABLE, /* force read-only */ + }, + + /* yaffs */ + { + .name = "yaffs", + .offset = (44 * SZ_1M), + .size = (20 * SZ_1M), + }, + + /* bootloader environment */ + { + .name = "env", + .offset = (160 * SZ_1K), + .size = (16 * SZ_1K), + }, + + /* upgrade images */ + { + .name = "zimage", + .offset = (22 * SZ_1M), + .size = (2 * SZ_1M) - (192 * SZ_1K), + }, { + .name = "cramfs", + .offset = (24 * SZ_1M) - (192*SZ_1K), + .size = (20 * SZ_1M), + }, +}; + +static struct mtd_partition jive_imageB_nand_part[] = { + +#ifdef CONFIG_MACH_JIVE_SHOW_BOOTLOADER + /* Don't allow access to the bootloader from linux */ + { + .name = "uboot", + .offset = 0, + .size = (160 * SZ_1K), + .mask_flags = MTD_WRITEABLE, /* force read-only */ + }, + + /* spare */ + { + .name = "spare", + .offset = (176 * SZ_1K), + .size = (16 * SZ_1K), + }, +#endif + + /* booted images */ + { + .name = "kernel (ro)", + .offset = (22 * SZ_1M), + .size = (2 * SZ_1M) - (192 * SZ_1K), + .mask_flags = MTD_WRITEABLE, /* force read-only */ + }, + { + .name = "root (ro)", + .offset = (24 * SZ_1M) - (192 * SZ_1K), + .size = (20 * SZ_1M), + .mask_flags = MTD_WRITEABLE, /* force read-only */ + }, + + /* yaffs */ + { + .name = "yaffs", + .offset = (44 * SZ_1M), + .size = (20 * SZ_1M), + }, + + /* bootloader environment */ + { + .name = "env", + .offset = (160 * SZ_1K), + .size = (16 * SZ_1K), + }, + + /* upgrade images */ + { + .name = "zimage", + .offset = (192 * SZ_1K), + .size = (2 * SZ_1M) - (192 * SZ_1K), + }, { + .name = "cramfs", + .offset = (2 * SZ_1M), + .size = (20 * SZ_1M), + }, +}; + +static struct s3c2410_nand_set jive_nand_sets[] = { + [0] = { + .name = "flash", + .nr_chips = 1, + .nr_partitions = ARRAY_SIZE(jive_imageA_nand_part), + .partitions = jive_imageA_nand_part, + }, +}; + +static struct s3c2410_platform_nand jive_nand_info = { + /* set taken from osiris nand timings, possibly still conservative */ + .tacls = 30, + .twrph0 = 55, + .twrph1 = 40, + .sets = jive_nand_sets, + .nr_sets = ARRAY_SIZE(jive_nand_sets), +}; + +static int __init jive_mtdset(char *options) +{ + struct s3c2410_nand_set *nand = &jive_nand_sets[0]; + unsigned long set; + + if (options == NULL || options[0] == '\0') + return 0; + + if (strict_strtoul(options, 10, &set)) { + printk(KERN_ERR "failed to parse mtdset=%s\n", options); + return 0; + } + + switch (set) { + case 1: + nand->nr_partitions = ARRAY_SIZE(jive_imageB_nand_part); + nand->partitions = jive_imageB_nand_part; + case 0: + /* this is already setup in the nand info */ + break; + default: + printk(KERN_ERR "Unknown mtd set %ld specified," + "using default.", set); + } + + return 0; +} + +/* parse the mtdset= option given to the kernel command line */ +__setup("mtdset=", jive_mtdset); + +/* LCD timing and setup */ + +#define LCD_XRES (240) +#define LCD_YRES (320) +#define LCD_LEFT_MARGIN (12) +#define LCD_RIGHT_MARGIN (12) +#define LCD_LOWER_MARGIN (12) +#define LCD_UPPER_MARGIN (12) +#define LCD_VSYNC (2) +#define LCD_HSYNC (2) + +#define LCD_REFRESH (60) + +#define LCD_HTOT (LCD_HSYNC + LCD_LEFT_MARGIN + LCD_XRES + LCD_RIGHT_MARGIN) +#define LCD_VTOT (LCD_VSYNC + LCD_LOWER_MARGIN + LCD_YRES + LCD_UPPER_MARGIN) + +struct s3c2410fb_display jive_vgg2432a4_display[] = { + [0] = { + .width = LCD_XRES, + .height = LCD_YRES, + .xres = LCD_XRES, + .yres = LCD_YRES, + .left_margin = LCD_LEFT_MARGIN, + .right_margin = LCD_RIGHT_MARGIN, + .upper_margin = LCD_UPPER_MARGIN, + .lower_margin = LCD_LOWER_MARGIN, + .hsync_len = LCD_HSYNC, + .vsync_len = LCD_VSYNC, + + .pixclock = (1000000000000LL / + (LCD_REFRESH * LCD_HTOT * LCD_VTOT)), + + .bpp = 16, + .type = (S3C2410_LCDCON1_TFT16BPP | + S3C2410_LCDCON1_TFT), + + .lcdcon5 = (S3C2410_LCDCON5_FRM565 | + S3C2410_LCDCON5_INVVLINE | + S3C2410_LCDCON5_INVVFRAME | + S3C2410_LCDCON5_INVVDEN | + S3C2410_LCDCON5_PWREN), + }, +}; + +/* todo - put into gpio header */ + +#define S3C2410_GPCCON_MASK(x) (3 << ((x) * 2)) +#define S3C2410_GPDCON_MASK(x) (3 << ((x) * 2)) + +struct s3c2410fb_mach_info jive_lcd_config = { + .displays = jive_vgg2432a4_display, + .num_displays = ARRAY_SIZE(jive_vgg2432a4_display), + .default_display = 0, + + /* Enable VD[2..7], VD[10..15], VD[18..23] and VCLK, syncs, VDEN + * and disable the pull down resistors on pins we are using for LCD + * data. */ + + .gpcup = (0xf << 1) | (0x3f << 10), + + .gpccon = (S3C2410_GPC1_VCLK | S3C2410_GPC2_VLINE | + S3C2410_GPC3_VFRAME | S3C2410_GPC4_VM | + S3C2410_GPC10_VD2 | S3C2410_GPC11_VD3 | + S3C2410_GPC12_VD4 | S3C2410_GPC13_VD5 | + S3C2410_GPC14_VD6 | S3C2410_GPC15_VD7), + + .gpccon_mask = (S3C2410_GPCCON_MASK(1) | S3C2410_GPCCON_MASK(2) | + S3C2410_GPCCON_MASK(3) | S3C2410_GPCCON_MASK(4) | + S3C2410_GPCCON_MASK(10) | S3C2410_GPCCON_MASK(11) | + S3C2410_GPCCON_MASK(12) | S3C2410_GPCCON_MASK(13) | + S3C2410_GPCCON_MASK(14) | S3C2410_GPCCON_MASK(15)), + + .gpdup = (0x3f << 2) | (0x3f << 10), + + .gpdcon = (S3C2410_GPD2_VD10 | S3C2410_GPD3_VD11 | + S3C2410_GPD4_VD12 | S3C2410_GPD5_VD13 | + S3C2410_GPD6_VD14 | S3C2410_GPD7_VD15 | + S3C2410_GPD10_VD18 | S3C2410_GPD11_VD19 | + S3C2410_GPD12_VD20 | S3C2410_GPD13_VD21 | + S3C2410_GPD14_VD22 | S3C2410_GPD15_VD23), + + .gpdcon_mask = (S3C2410_GPDCON_MASK(2) | S3C2410_GPDCON_MASK(3) | + S3C2410_GPDCON_MASK(4) | S3C2410_GPDCON_MASK(5) | + S3C2410_GPDCON_MASK(6) | S3C2410_GPDCON_MASK(7) | + S3C2410_GPDCON_MASK(10) | S3C2410_GPDCON_MASK(11)| + S3C2410_GPDCON_MASK(12) | S3C2410_GPDCON_MASK(13)| + S3C2410_GPDCON_MASK(14) | S3C2410_GPDCON_MASK(15)), +}; + +/* ILI9320 support. */ + +static void jive_lcm_reset(unsigned int set) +{ + printk(KERN_DEBUG "%s(%d)\n", __func__, set); + + s3c2410_gpio_setpin(S3C2410_GPG13, set); + s3c2410_gpio_cfgpin(S3C2410_GPG13, S3C2410_GPIO_OUTPUT); +} + +#undef LCD_UPPER_MARGIN +#define LCD_UPPER_MARGIN 2 + +static struct ili9320_platdata jive_lcm_config = { + .hsize = LCD_XRES, + .vsize = LCD_YRES, + + .reset = jive_lcm_reset, + .suspend = ILI9320_SUSPEND_DEEP, + + .entry_mode = ILI9320_ENTRYMODE_ID(3) | ILI9320_ENTRYMODE_BGR, + .display2 = (ILI9320_DISPLAY2_FP(LCD_UPPER_MARGIN) | + ILI9320_DISPLAY2_BP(LCD_LOWER_MARGIN)), + .display3 = 0x0, + .display4 = 0x0, + .rgb_if1 = (ILI9320_RGBIF1_RIM_RGB18 | + ILI9320_RGBIF1_RM | ILI9320_RGBIF1_CLK_RGBIF), + .rgb_if2 = ILI9320_RGBIF2_DPL, + .interface2 = 0x0, + .interface3 = 0x3, + .interface4 = (ILI9320_INTERFACE4_RTNE(16) | + ILI9320_INTERFACE4_DIVE(1)), + .interface5 = 0x0, + .interface6 = 0x0, +}; + +/* LCD SPI support */ + +static void jive_lcd_spi_chipselect(struct s3c2410_spigpio_info *spi, int cs) +{ + s3c2410_gpio_setpin(S3C2410_GPB7, cs ? 0 : 1); +} + +static struct s3c2410_spigpio_info jive_lcd_spi = { + .bus_num = 0, + .pin_clk = S3C2410_GPG8, + .pin_mosi = S3C2410_GPB8, + .chip_select = jive_lcd_spi_chipselect, +}; + +static struct platform_device jive_device_lcdspi = { + .name = "s3c24xx-spi-gpio", + .id = 1, + .num_resources = 0, + .dev.platform_data = &jive_lcd_spi, +}; + +/* WM8750 audio code SPI definition */ + +static void jive_wm8750_chipselect(struct s3c2410_spigpio_info *spi, int cs) +{ + s3c2410_gpio_setpin(S3C2410_GPH10, cs ? 0 : 1); +} + +static struct s3c2410_spigpio_info jive_wm8750_spi = { + .bus_num = 2, + .pin_clk = S3C2410_GPB4, + .pin_mosi = S3C2410_GPB9, + .chip_select = jive_wm8750_chipselect, +}; + +static struct platform_device jive_device_wm8750 = { + .name = "s3c24xx-spi-gpio", + .id = 2, + .num_resources = 0, + .dev.platform_data = &jive_wm8750_spi, +}; + +/* JIVE SPI devices. */ + +static struct spi_board_info __initdata jive_spi_devs[] = { + [0] = { + .modalias = "VGG2432A4", + .bus_num = 1, + .chip_select = 0, + .mode = SPI_MODE_3, /* CPOL=1, CPHA=1 */ + .max_speed_hz = 100000, + .platform_data = &jive_lcm_config, + }, { + .modalias = "WM8750", + .bus_num = 2, + .chip_select = 0, + .mode = SPI_MODE_0, /* CPOL=0, CPHA=0 */ + .max_speed_hz = 100000, + }, +}; + +/* I2C bus and device configuration. */ + +static struct s3c2410_platform_i2c jive_i2c_cfg = { + .max_freq = 80 * 1000, + .bus_freq = 50 * 1000, + .flags = S3C_IICFLG_FILTER, + .sda_delay = 2, +}; + +static struct i2c_board_info jive_i2c_devs[] = { + [0] = { + I2C_BOARD_INFO("lis302dl", 0x1c), + .irq = IRQ_EINT14, + }, +}; + +/* The platform devices being used. */ + +static struct platform_device *jive_devices[] __initdata = { + &s3c_device_usb, + &s3c_device_rtc, + &s3c_device_wdt, + &s3c_device_i2c, + &s3c_device_lcd, + &jive_device_lcdspi, + &jive_device_wm8750, + &s3c_device_nand, + &s3c_device_usbgadget, +}; + +static struct s3c2410_udc_mach_info jive_udc_cfg __initdata = { + .vbus_pin = S3C2410_GPG1, /* detect is on GPG1 */ +}; + +/* Jive power management device */ + +#ifdef CONFIG_PM +static int jive_pm_suspend(struct sys_device *sd, pm_message_t state) +{ + /* Write the magic value u-boot uses to check for resume into + * the INFORM0 register, and ensure INFORM1 is set to the + * correct address to resume from. */ + + __raw_writel(0x2BED, S3C2412_INFORM0); + __raw_writel(virt_to_phys(s3c2410_cpu_resume), S3C2412_INFORM1); + + return 0; +} + +static int jive_pm_resume(struct sys_device *sd) +{ + __raw_writel(0x0, S3C2412_INFORM0); + return 0; +} + +#else +#define jive_pm_suspend NULL +#define jive_pm_resume NULL +#endif + +static struct sysdev_class jive_pm_sysclass = { + .name = "jive-pm", + .suspend = jive_pm_suspend, + .resume = jive_pm_resume, +}; + +static struct sys_device jive_pm_sysdev = { + .cls = &jive_pm_sysclass, +}; + +static void __init jive_map_io(void) +{ + s3c24xx_init_io(jive_iodesc, ARRAY_SIZE(jive_iodesc)); + s3c24xx_init_clocks(12000000); + s3c24xx_init_uarts(jive_uartcfgs, ARRAY_SIZE(jive_uartcfgs)); +} + +static void jive_power_off(void) +{ + printk(KERN_INFO "powering system down...\n"); + + s3c2410_gpio_setpin(S3C2410_GPC5, 1); + s3c2410_gpio_cfgpin(S3C2410_GPC5, S3C2410_GPIO_OUTPUT); +} + +static void __init jive_machine_init(void) +{ + /* register system devices for managing low level suspend */ + + sysdev_class_register(&jive_pm_sysclass); + sysdev_register(&jive_pm_sysdev); + + /* write our sleep configurations for the IO. Pull down all unused + * IO, ensure that we have turned off all peripherals we do not + * need, and configure the ones we do need. */ + + /* Port B sleep */ + + __raw_writel(S3C2412_SLPCON_IN(0) | + S3C2412_SLPCON_PULL(1) | + S3C2412_SLPCON_HIGH(2) | + S3C2412_SLPCON_PULL(3) | + S3C2412_SLPCON_PULL(4) | + S3C2412_SLPCON_PULL(5) | + S3C2412_SLPCON_PULL(6) | + S3C2412_SLPCON_HIGH(7) | + S3C2412_SLPCON_PULL(8) | + S3C2412_SLPCON_PULL(9) | + S3C2412_SLPCON_PULL(10), S3C2412_GPBSLPCON); + + /* Port C sleep */ + + __raw_writel(S3C2412_SLPCON_PULL(0) | + S3C2412_SLPCON_PULL(1) | + S3C2412_SLPCON_PULL(2) | + S3C2412_SLPCON_PULL(3) | + S3C2412_SLPCON_PULL(4) | + S3C2412_SLPCON_PULL(5) | + S3C2412_SLPCON_LOW(6) | + S3C2412_SLPCON_PULL(6) | + S3C2412_SLPCON_PULL(7) | + S3C2412_SLPCON_PULL(8) | + S3C2412_SLPCON_PULL(9) | + S3C2412_SLPCON_PULL(10) | + S3C2412_SLPCON_PULL(11) | + S3C2412_SLPCON_PULL(12) | + S3C2412_SLPCON_PULL(13) | + S3C2412_SLPCON_PULL(14) | + S3C2412_SLPCON_PULL(15), S3C2412_GPCSLPCON); + + /* Port D sleep */ + + __raw_writel(S3C2412_SLPCON_ALL_PULL, S3C2412_GPDSLPCON); + + /* Port F sleep */ + + __raw_writel(S3C2412_SLPCON_LOW(0) | + S3C2412_SLPCON_LOW(1) | + S3C2412_SLPCON_LOW(2) | + S3C2412_SLPCON_EINT(3) | + S3C2412_SLPCON_EINT(4) | + S3C2412_SLPCON_EINT(5) | + S3C2412_SLPCON_EINT(6) | + S3C2412_SLPCON_EINT(7), S3C2412_GPFSLPCON); + + /* Port G sleep */ + + __raw_writel(S3C2412_SLPCON_IN(0) | + S3C2412_SLPCON_IN(1) | + S3C2412_SLPCON_IN(2) | + S3C2412_SLPCON_IN(3) | + S3C2412_SLPCON_IN(4) | + S3C2412_SLPCON_IN(5) | + S3C2412_SLPCON_IN(6) | + S3C2412_SLPCON_IN(7) | + S3C2412_SLPCON_PULL(8) | + S3C2412_SLPCON_PULL(9) | + S3C2412_SLPCON_IN(10) | + S3C2412_SLPCON_PULL(11) | + S3C2412_SLPCON_PULL(12) | + S3C2412_SLPCON_PULL(13) | + S3C2412_SLPCON_IN(14) | + S3C2412_SLPCON_PULL(15), S3C2412_GPGSLPCON); + + /* Port H sleep */ + + __raw_writel(S3C2412_SLPCON_PULL(0) | + S3C2412_SLPCON_PULL(1) | + S3C2412_SLPCON_PULL(2) | + S3C2412_SLPCON_PULL(3) | + S3C2412_SLPCON_PULL(4) | + S3C2412_SLPCON_PULL(5) | + S3C2412_SLPCON_PULL(6) | + S3C2412_SLPCON_IN(7) | + S3C2412_SLPCON_IN(8) | + S3C2412_SLPCON_PULL(9) | + S3C2412_SLPCON_IN(10), S3C2412_GPHSLPCON); + + /* initialise the power management now we've setup everything. */ + + s3c2410_pm_init(); + + s3c_device_nand.dev.platform_data = &jive_nand_info; + + /* initialise the spi */ + + s3c2410_gpio_setpin(S3C2410_GPG13, 0); + s3c2410_gpio_cfgpin(S3C2410_GPG13, S3C2410_GPIO_OUTPUT); + + s3c2410_gpio_setpin(S3C2410_GPB7, 1); + s3c2410_gpio_cfgpin(S3C2410_GPB7, S3C2410_GPIO_OUTPUT); + + s3c2410_gpio_setpin(S3C2410_GPB6, 0); + s3c2410_gpio_cfgpin(S3C2410_GPB6, S3C2410_GPIO_OUTPUT); + + s3c2410_gpio_setpin(S3C2410_GPG8, 1); + s3c2410_gpio_cfgpin(S3C2410_GPG8, S3C2410_GPIO_OUTPUT); + + /* initialise the WM8750 spi */ + + s3c2410_gpio_setpin(S3C2410_GPH10, 1); + s3c2410_gpio_cfgpin(S3C2410_GPH10, S3C2410_GPIO_OUTPUT); + + /* Turn off suspend on both USB ports, and switch the + * selectable USB port to USB device mode. */ + + s3c2410_modify_misccr(S3C2410_MISCCR_USBHOST | + S3C2410_MISCCR_USBSUSPND0 | + S3C2410_MISCCR_USBSUSPND1, 0x0); + + s3c24xx_udc_set_platdata(&jive_udc_cfg); + s3c24xx_fb_set_platdata(&jive_lcd_config); + + spi_register_board_info(jive_spi_devs, ARRAY_SIZE(jive_spi_devs)); + + s3c_device_i2c.dev.platform_data = &jive_i2c_cfg; + i2c_register_board_info(0, jive_i2c_devs, ARRAY_SIZE(jive_i2c_devs)); + + pm_power_off = jive_power_off; + + platform_add_devices(jive_devices, ARRAY_SIZE(jive_devices)); +} + +MACHINE_START(JIVE, "JIVE") + /* Maintainer: Ben Dooks <ben@fluff.org> */ + .phys_io = S3C2410_PA_UART, + .io_pg_offst = (((u32)S3C24XX_VA_UART) >> 18) & 0xfffc, + .boot_params = S3C2410_SDRAM_PA + 0x100, + + .init_irq = s3c24xx_init_irq, + .map_io = jive_map_io, + .init_machine = jive_machine_init, + .timer = &s3c24xx_timer, +MACHINE_END diff --git a/arch/arm/mach-s3c2440/Kconfig b/arch/arm/mach-s3c2440/Kconfig index f1915bd61d1..25de042ab99 100644 --- a/arch/arm/mach-s3c2440/Kconfig +++ b/arch/arm/mach-s3c2440/Kconfig @@ -29,6 +29,7 @@ config MACH_ANUBIS bool "Simtec Electronics ANUBIS" select CPU_S3C2440 select PM_SIMTEC if PM + select HAVE_PATA_PLATFORM help Say Y here if you are using the Simtec Electronics ANUBIS development system @@ -67,6 +68,11 @@ config SMDK2440_CPU2440 default y if ARCH_S3C2440 select CPU_S3C2440 +config MACH_AT2440EVB + bool "Avantech AT2440EVB development board" + select CPU_S3C2440 + help + Say Y here if you are using the AT2440EVB development board endmenu diff --git a/arch/arm/mach-s3c2440/Makefile b/arch/arm/mach-s3c2440/Makefile index c81ed6248dc..0b4440e79b9 100644 --- a/arch/arm/mach-s3c2440/Makefile +++ b/arch/arm/mach-s3c2440/Makefile @@ -21,3 +21,4 @@ obj-$(CONFIG_MACH_OSIRIS) += mach-osiris.o obj-$(CONFIG_MACH_RX3715) += mach-rx3715.o obj-$(CONFIG_ARCH_S3C2440) += mach-smdk2440.o obj-$(CONFIG_MACH_NEXCODER_2440) += mach-nexcoder.o +obj-$(CONFIG_MACH_AT2440EVB) += mach-at2440evb.o diff --git a/arch/arm/mach-s3c2440/mach-anubis.c b/arch/arm/mach-s3c2440/mach-anubis.c index 47258915a2f..09af8b23500 100644 --- a/arch/arm/mach-s3c2440/mach-anubis.c +++ b/arch/arm/mach-s3c2440/mach-anubis.c @@ -1,6 +1,6 @@ /* linux/arch/arm/mach-s3c2440/mach-anubis.c * - * Copyright (c) 2003-2005 Simtec Electronics + * Copyright (c) 2003-2005,2008 Simtec Electronics * http://armlinux.simtec.co.uk/ * Ben Dooks <ben@simtec.co.uk> * @@ -17,6 +17,8 @@ #include <linux/init.h> #include <linux/serial_core.h> #include <linux/platform_device.h> +#include <linux/ata_platform.h> +#include <linux/i2c.h> #include <linux/sm501.h> #include <linux/sm501-regs.h> @@ -241,14 +243,18 @@ static struct s3c2410_platform_nand anubis_nand_info = { /* IDE channels */ +struct pata_platform_info anubis_ide_platdata = { + .ioport_shift = 5, +}; + static struct resource anubis_ide0_resource[] = { { .start = S3C2410_CS3, .end = S3C2410_CS3 + (8*32) - 1, .flags = IORESOURCE_MEM, }, { - .start = S3C2410_CS3 + (1<<26), - .end = S3C2410_CS3 + (1<<26) + (8*32) - 1, + .start = S3C2410_CS3 + (1<<26) + (6*32), + .end = S3C2410_CS3 + (1<<26) + (7*32) - 1, .flags = IORESOURCE_MEM, }, { .start = IRQ_IDE0, @@ -258,10 +264,14 @@ static struct resource anubis_ide0_resource[] = { }; static struct platform_device anubis_device_ide0 = { - .name = "simtec-ide", + .name = "pata_platform", .id = 0, .num_resources = ARRAY_SIZE(anubis_ide0_resource), .resource = anubis_ide0_resource, + .dev = { + .platform_data = &anubis_ide_platdata, + .coherent_dma_mask = ~0, + }, }; static struct resource anubis_ide1_resource[] = { @@ -270,8 +280,8 @@ static struct resource anubis_ide1_resource[] = { .end = S3C2410_CS4 + (8*32) - 1, .flags = IORESOURCE_MEM, }, { - .start = S3C2410_CS4 + (1<<26), - .end = S3C2410_CS4 + (1<<26) + (8*32) - 1, + .start = S3C2410_CS4 + (1<<26) + (6*32), + .end = S3C2410_CS4 + (1<<26) + (7*32) - 1, .flags = IORESOURCE_MEM, }, { .start = IRQ_IDE0, @@ -280,12 +290,15 @@ static struct resource anubis_ide1_resource[] = { }, }; - static struct platform_device anubis_device_ide1 = { - .name = "simtec-ide", + .name = "pata_platform", .id = 1, .num_resources = ARRAY_SIZE(anubis_ide1_resource), .resource = anubis_ide1_resource, + .dev = { + .platform_data = &anubis_ide_platdata, + .coherent_dma_mask = ~0, + }, }; /* Asix AX88796 10/100 ethernet controller */ @@ -409,6 +422,15 @@ static struct clk *anubis_clocks[] = { &s3c24xx_uclk, }; +/* I2C devices. */ + +static struct i2c_board_info anubis_i2c_devs[] __initdata = { + { + I2C_BOARD_INFO("tps65011", 0x48), + .irq = IRQ_EINT20, + } +}; + static void __init anubis_map_io(void) { /* initialise the clocks */ @@ -448,6 +470,9 @@ static void __init anubis_map_io(void) static void __init anubis_init(void) { platform_add_devices(anubis_devices, ARRAY_SIZE(anubis_devices)); + + i2c_register_board_info(0, anubis_i2c_devs, + ARRAY_SIZE(anubis_i2c_devs)); } diff --git a/arch/arm/mach-s3c2440/mach-at2440evb.c b/arch/arm/mach-s3c2440/mach-at2440evb.c new file mode 100644 index 00000000000..f5e3c7f2763 --- /dev/null +++ b/arch/arm/mach-s3c2440/mach-at2440evb.c @@ -0,0 +1,198 @@ +/* linux/arch/arm/mach-s3c2440/mach-at2440evb.c + * + * Copyright (c) 2008 Ramax Lo <ramaxlo@gmail.com> + * Based on mach-anubis.c by Ben Dooks <ben@simtec.co.uk> + * and modifications by SBZ <sbz@spgui.org> and + * Weibing <http://weibing.blogbus.com> + * + * For product information, visit http://www.arm9e.com/ + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. +*/ + +#include <linux/kernel.h> +#include <linux/types.h> +#include <linux/interrupt.h> +#include <linux/list.h> +#include <linux/timer.h> +#include <linux/init.h> +#include <linux/io.h> +#include <linux/serial_core.h> +#include <linux/dm9000.h> +#include <linux/platform_device.h> + +#include <asm/mach/arch.h> +#include <asm/mach/map.h> +#include <asm/mach/irq.h> + +#include <asm/hardware.h> +#include <asm/irq.h> +#include <asm/mach-types.h> + +#include <asm/plat-s3c/regs-serial.h> +#include <asm/arch/regs-gpio.h> +#include <asm/arch/regs-mem.h> +#include <asm/arch/regs-lcd.h> +#include <asm/plat-s3c/nand.h> + +#include <linux/mtd/mtd.h> +#include <linux/mtd/nand.h> +#include <linux/mtd/nand_ecc.h> +#include <linux/mtd/partitions.h> + +#include <asm/plat-s3c24xx/clock.h> +#include <asm/plat-s3c24xx/devs.h> +#include <asm/plat-s3c24xx/cpu.h> + +static struct map_desc at2440evb_iodesc[] __initdata = { + /* Nothing here */ +}; + +#define UCON S3C2410_UCON_DEFAULT +#define ULCON (S3C2410_LCON_CS8 | S3C2410_LCON_PNONE) +#define UFCON (S3C2410_UFCON_RXTRIG8 | S3C2410_UFCON_FIFOMODE) + +static struct s3c24xx_uart_clksrc at2440evb_serial_clocks[] = { + [0] = { + .name = "uclk", + .divisor = 1, + .min_baud = 0, + .max_baud = 0, + }, + [1] = { + .name = "pclk", + .divisor = 1, + .min_baud = 0, + .max_baud = 0, + } +}; + + +static struct s3c2410_uartcfg at2440evb_uartcfgs[] __initdata = { + [0] = { + .hwport = 0, + .flags = 0, + .ucon = UCON, + .ulcon = ULCON, + .ufcon = UFCON, + .clocks = at2440evb_serial_clocks, + .clocks_size = ARRAY_SIZE(at2440evb_serial_clocks), + }, + [1] = { + .hwport = 1, + .flags = 0, + .ucon = UCON, + .ulcon = ULCON, + .ufcon = UFCON, + .clocks = at2440evb_serial_clocks, + .clocks_size = ARRAY_SIZE(at2440evb_serial_clocks), + }, +}; + +/* NAND Flash on AT2440EVB board */ + +static struct mtd_partition at2440evb_default_nand_part[] = { + [0] = { + .name = "Boot Agent", + .size = SZ_256K, + .offset = 0, + }, + [1] = { + .name = "Kernel", + .size = SZ_2M, + .offset = SZ_256K, + }, + [2] = { + .name = "Root", + .offset = SZ_256K + SZ_2M, + .size = MTDPART_SIZ_FULL, + }, +}; + +static struct s3c2410_nand_set at2440evb_nand_sets[] = { + [0] = { + .name = "nand", + .nr_chips = 1, + .nr_partitions = ARRAY_SIZE(at2440evb_default_nand_part), + .partitions = at2440evb_default_nand_part, + }, +}; + +static struct s3c2410_platform_nand at2440evb_nand_info = { + .tacls = 25, + .twrph0 = 55, + .twrph1 = 40, + .nr_sets = ARRAY_SIZE(at2440evb_nand_sets), + .sets = at2440evb_nand_sets, +}; + +/* DM9000AEP 10/100 ethernet controller */ + +static struct resource at2440evb_dm9k_resource[] = { + [0] = { + .start = S3C2410_CS3, + .end = S3C2410_CS3 + 3, + .flags = IORESOURCE_MEM + }, + [1] = { + .start = S3C2410_CS3 + 4, + .end = S3C2410_CS3 + 7, + .flags = IORESOURCE_MEM + }, + [2] = { + .start = IRQ_EINT7, + .end = IRQ_EINT7, + .flags = IORESOURCE_IRQ | IORESOURCE_IRQ_HIGHEDGE, + } +}; + +static struct dm9000_plat_data at2440evb_dm9k_pdata = { + .flags = (DM9000_PLATF_16BITONLY | DM9000_PLATF_NO_EEPROM), +}; + +static struct platform_device at2440evb_device_eth = { + .name = "dm9000", + .id = -1, + .num_resources = ARRAY_SIZE(at2440evb_dm9k_resource), + .resource = at2440evb_dm9k_resource, + .dev = { + .platform_data = &at2440evb_dm9k_pdata, + }, +}; + +static struct platform_device *at2440evb_devices[] __initdata = { + &s3c_device_usb, + &s3c_device_wdt, + &s3c_device_adc, + &s3c_device_i2c, + &s3c_device_rtc, + &s3c_device_nand, + &at2440evb_device_eth, +}; + +static void __init at2440evb_map_io(void) +{ + s3c_device_nand.dev.platform_data = &at2440evb_nand_info; + + s3c24xx_init_io(at2440evb_iodesc, ARRAY_SIZE(at2440evb_iodesc)); + s3c24xx_init_clocks(16934400); + s3c24xx_init_uarts(at2440evb_uartcfgs, ARRAY_SIZE(at2440evb_uartcfgs)); +} + +static void __init at2440evb_init(void) +{ + platform_add_devices(at2440evb_devices, ARRAY_SIZE(at2440evb_devices)); +} + + +MACHINE_START(AT2440EVB, "AT2440EVB") + .phys_io = S3C2410_PA_UART, + .io_pg_offst = (((u32)S3C24XX_VA_UART) >> 18) & 0xfffc, + .boot_params = S3C2410_SDRAM_PA + 0x100, + .map_io = at2440evb_map_io, + .init_machine = at2440evb_init, + .init_irq = s3c24xx_init_irq, + .timer = &s3c24xx_timer, +MACHINE_END diff --git a/arch/arm/mach-s3c2440/mach-osiris.c b/arch/arm/mach-s3c2440/mach-osiris.c index 8a8acdbd072..af996b0e91e 100644 --- a/arch/arm/mach-s3c2440/mach-osiris.c +++ b/arch/arm/mach-s3c2440/mach-osiris.c @@ -1,6 +1,6 @@ /* linux/arch/arm/mach-s3c2440/mach-osiris.c * - * Copyright (c) 2005 Simtec Electronics + * Copyright (c) 2005,2008 Simtec Electronics * http://armlinux.simtec.co.uk/ * Ben Dooks <ben@simtec.co.uk> * @@ -19,6 +19,7 @@ #include <linux/sysdev.h> #include <linux/serial_core.h> #include <linux/clk.h> +#include <linux/i2c.h> #include <asm/mach/arch.h> #include <asm/mach/map.h> @@ -322,6 +323,15 @@ static struct sys_device osiris_pm_sysdev = { .cls = &osiris_pm_sysclass, }; +/* I2C devices fitted. */ + +static struct i2c_board_info osiris_i2c_devs[] __initdata = { + { + I2C_BOARD_INFO("tps65011", 0x48), + .irq = IRQ_EINT20, + }, +}; + /* Standard Osiris devices */ static struct platform_device *osiris_devices[] __initdata = { @@ -388,6 +398,9 @@ static void __init osiris_init(void) sysdev_class_register(&osiris_pm_sysclass); sysdev_register(&osiris_pm_sysdev); + i2c_register_board_info(0, osiris_i2c_devs, + ARRAY_SIZE(osiris_i2c_devs)); + platform_add_devices(osiris_devices, ARRAY_SIZE(osiris_devices)); }; diff --git a/arch/arm/mach-s3c2443/clock.c b/arch/arm/mach-s3c2443/clock.c index b42f956738d..17f064fabda 100644 --- a/arch/arm/mach-s3c2443/clock.c +++ b/arch/arm/mach-s3c2443/clock.c @@ -81,7 +81,7 @@ static int s3c2443_clkcon_enable_p(struct clk *clk, int enable) else clkcon &= ~clocks; - __raw_writel(clkcon, S3C2443_HCLKCON); + __raw_writel(clkcon, S3C2443_PCLKCON); return 0; } @@ -221,7 +221,6 @@ static struct clk clk_mdivclk = { .get_rate = s3c2443_getrate_mdivclk, }; - static int s3c2443_setparent_msysclk(struct clk *clk, struct clk *parent) { unsigned long clksrc = __raw_readl(S3C2443_CLKSRC); @@ -249,6 +248,46 @@ static struct clk clk_msysclk = { .set_parent = s3c2443_setparent_msysclk, }; +/* armdiv + * + * this clock is sourced from msysclk and can have a number of + * divider values applied to it to then be fed into armclk. +*/ + +static struct clk clk_armdiv = { + .name = "armdiv", + .id = -1, + .parent = &clk_msysclk, +}; + +/* armclk + * + * this is the clock fed into the ARM core itself, either from + * armdiv or from hclk. + */ + +static int s3c2443_setparent_armclk(struct clk *clk, struct clk *parent) +{ + unsigned long clkdiv0; + + clkdiv0 = __raw_readl(S3C2443_CLKDIV0); + + if (parent == &clk_armdiv) + clkdiv0 &= ~S3C2443_CLKDIV0_DVS; + else if (parent == &clk_h) + clkdiv0 |= S3C2443_CLKDIV0_DVS; + else + return -EINVAL; + + __raw_writel(clkdiv0, S3C2443_CLKDIV0); + return 0; +} + +static struct clk clk_arm = { + .name = "armclk", + .id = -1, + .set_parent = s3c2443_setparent_armclk, +}; /* esysclk * @@ -639,6 +678,29 @@ static struct clk clk_display = { .round_rate = s3c2443_roundrate_clksrc256, }; +/* prediv + * + * this divides the msysclk down to pass to h/p/etc. + */ + +static unsigned long s3c2443_prediv_getrate(struct clk *clk) +{ + unsigned long rate = clk_get_rate(clk->parent); + unsigned long clkdiv0 = __raw_readl(S3C2443_CLKDIV0); + + clkdiv0 &= S3C2443_CLKDIV0_PREDIV_MASK; + clkdiv0 >>= S3C2443_CLKDIV0_PREDIV_SHIFT; + + return rate / (clkdiv0 + 1); +} + +static struct clk clk_prediv = { + .name = "prediv", + .id = -1, + .parent = &clk_msysclk, + .get_rate = s3c2443_prediv_getrate, +}; + /* standard clock definitions */ static struct clk init_clocks_disable[] = { @@ -887,6 +949,15 @@ static void __init s3c2443_clk_initparents(void) } clk_init_set_parent(&clk_msysclk, parent); + + /* arm */ + + if (__raw_readl(S3C2443_CLKDIV0) & S3C2443_CLKDIV0_DVS) + parent = &clk_h; + else + parent = &clk_armdiv; + + clk_init_set_parent(&clk_arm, parent); } /* armdiv divisor table */ @@ -909,10 +980,9 @@ static inline unsigned int s3c2443_fclk_div(unsigned long clkcon0) return armdiv[clkcon0 >> S3C2443_CLKDIV0_ARMDIV_SHIFT]; } -static inline unsigned long s3c2443_get_prediv(unsigned long clkcon0) +static inline unsigned long s3c2443_get_hdiv(unsigned long clkcon0) { - clkcon0 &= S3C2443_CLKDIV0_PREDIV_MASK; - clkcon0 >>= S3C2443_CLKDIV0_PREDIV_SHIFT; + clkcon0 &= S3C2443_CLKDIV0_HCLKDIV_MASK; return clkcon0 + 1; } @@ -936,6 +1006,9 @@ static struct clk *clks[] __initdata = { &clk_hsspi, &clk_hsmmc_div, &clk_hsmmc, + &clk_armdiv, + &clk_arm, + &clk_prediv, }; void __init s3c2443_init_clocks(int xtal) @@ -951,10 +1024,16 @@ void __init s3c2443_init_clocks(int xtal) int ret; int ptr; + /* s3c2443 parents h and p clocks from prediv */ + clk_h.parent = &clk_prediv; + clk_p.parent = &clk_prediv; + pll = s3c2443_get_mpll(mpllcon, xtal); + clk_msysclk.rate = pll; fclk = pll / s3c2443_fclk_div(clkdiv0); - hclk = fclk / s3c2443_get_prediv(clkdiv0); + hclk = s3c2443_prediv_getrate(&clk_prediv); + hclk = hclk / s3c2443_get_hdiv(clkdiv0); hclk = hclk / ((clkdiv0 & S3C2443_CLKDIV0_HALF_HCLK) ? 2 : 1); pclk = hclk / ((clkdiv0 & S3C2443_CLKDIV0_HALF_PCLK) ? 2 : 1); diff --git a/arch/arm/mm/Kconfig b/arch/arm/mm/Kconfig index 68ea247bdd8..3a6c8ec34cd 100644 --- a/arch/arm/mm/Kconfig +++ b/arch/arm/mm/Kconfig @@ -180,8 +180,21 @@ config CPU_ARM925T # ARM926T config CPU_ARM926T bool "Support ARM926T processor" - depends on ARCH_INTEGRATOR || ARCH_VERSATILE_PB || MACH_VERSATILE_AB || ARCH_OMAP730 || ARCH_OMAP16XX || MACH_REALVIEW_EB || ARCH_PNX4008 || ARCH_NETX || CPU_S3C2412 || ARCH_AT91SAM9260 || ARCH_AT91SAM9261 || ARCH_AT91SAM9263 || ARCH_AT91SAM9RL || ARCH_AT91CAP9 || ARCH_NS9XXX || ARCH_DAVINCI || ARCH_MX2 - default y if ARCH_VERSATILE_PB || MACH_VERSATILE_AB || ARCH_OMAP730 || ARCH_OMAP16XX || ARCH_PNX4008 || ARCH_NETX || CPU_S3C2412 || ARCH_AT91SAM9260 || ARCH_AT91SAM9261 || ARCH_AT91SAM9263 || ARCH_AT91SAM9RL || ARCH_AT91CAP9 || ARCH_NS9XXX || ARCH_DAVINCI || ARCH_MX2 + depends on ARCH_INTEGRATOR || ARCH_VERSATILE_PB || \ + MACH_VERSATILE_AB || ARCH_OMAP730 || \ + ARCH_OMAP16XX || MACH_REALVIEW_EB || \ + ARCH_PNX4008 || ARCH_NETX || CPU_S3C2412 || \ + ARCH_AT91SAM9260 || ARCH_AT91SAM9261 || \ + ARCH_AT91SAM9263 || ARCH_AT91SAM9RL || \ + ARCH_AT91SAM9G20 || ARCH_AT91CAP9 || \ + ARCH_NS9XXX || ARCH_DAVINCI + default y if ARCH_VERSATILE_PB || MACH_VERSATILE_AB || \ + ARCH_OMAP730 || ARCH_OMAP16XX || \ + ARCH_PNX4008 || ARCH_NETX || CPU_S3C2412 || \ + ARCH_AT91SAM9260 || ARCH_AT91SAM9261 || \ + ARCH_AT91SAM9263 || ARCH_AT91SAM9RL || \ + ARCH_AT91SAM9G20 || ARCH_AT91CAP9 || \ + ARCH_NS9XXX || ARCH_DAVINCI || ARCH_MX2 select CPU_32v5 select CPU_ABRT_EV5TJ select CPU_PABRT_NOIFAR @@ -365,7 +378,7 @@ config CPU_XSC3 # Feroceon config CPU_FEROCEON bool - depends on ARCH_ORION5X + depends on ARCH_ORION5X || ARCH_LOKI || ARCH_KIRKWOOD || ARCH_MV78XX0 default y select CPU_32v5 select CPU_ABRT_EV5T @@ -373,7 +386,7 @@ config CPU_FEROCEON select CPU_CACHE_VIVT select CPU_CP15_MMU select CPU_COPY_FEROCEON if MMU - select CPU_TLB_V4WBI if MMU + select CPU_TLB_FEROCEON if MMU config CPU_FEROCEON_OLD_ID bool "Accept early Feroceon cores with an ARM926 ID" @@ -551,6 +564,11 @@ config CPU_TLB_V4WBI ARM Architecture Version 4 TLB with writeback cache and invalidate instruction cache entry. +config CPU_TLB_FEROCEON + bool + help + Feroceon TLB (v4wbi with non-outer-cachable page table walks). + config CPU_TLB_V6 bool @@ -709,6 +727,14 @@ config OUTER_CACHE bool default n +config CACHE_FEROCEON_L2 + bool "Enable the Feroceon L2 cache controller" + depends on ARCH_KIRKWOOD || ARCH_MV78XX0 + default y + select OUTER_CACHE + help + This option enables the Feroceon L2 cache controller. + config CACHE_L2X0 bool "Enable the L2x0 outer cache controller" depends on REALVIEW_EB_ARM11MP || MACH_REALVIEW_PB11MP || MACH_REALVIEW_PB1176 diff --git a/arch/arm/mm/Makefile b/arch/arm/mm/Makefile index 32b2d2d213a..f64b92557b1 100644 --- a/arch/arm/mm/Makefile +++ b/arch/arm/mm/Makefile @@ -46,6 +46,7 @@ obj-$(CONFIG_CPU_TLB_V3) += tlb-v3.o obj-$(CONFIG_CPU_TLB_V4WT) += tlb-v4.o obj-$(CONFIG_CPU_TLB_V4WB) += tlb-v4wb.o obj-$(CONFIG_CPU_TLB_V4WBI) += tlb-v4wbi.o +obj-$(CONFIG_CPU_TLB_FEROCEON) += tlb-v4wbi.o # reuse v4wbi TLB functions obj-$(CONFIG_CPU_TLB_V6) += tlb-v6.o obj-$(CONFIG_CPU_TLB_V7) += tlb-v7.o @@ -73,4 +74,5 @@ obj-$(CONFIG_CPU_FEROCEON) += proc-feroceon.o obj-$(CONFIG_CPU_V6) += proc-v6.o obj-$(CONFIG_CPU_V7) += proc-v7.o +obj-$(CONFIG_CACHE_FEROCEON_L2) += cache-feroceon-l2.o obj-$(CONFIG_CACHE_L2X0) += cache-l2x0.o diff --git a/arch/arm/mm/cache-feroceon-l2.c b/arch/arm/mm/cache-feroceon-l2.c new file mode 100644 index 00000000000..20eec4ba173 --- /dev/null +++ b/arch/arm/mm/cache-feroceon-l2.c @@ -0,0 +1,318 @@ +/* + * arch/arm/mm/cache-feroceon-l2.c - Feroceon L2 cache controller support + * + * Copyright (C) 2008 Marvell Semiconductor + * + * This file is licensed under the terms of the GNU General Public + * License version 2. This program is licensed "as is" without any + * warranty of any kind, whether express or implied. + * + * References: + * - Unified Layer 2 Cache for Feroceon CPU Cores, + * Document ID MV-S104858-00, Rev. A, October 23 2007. + */ + +#include <linux/init.h> +#include <asm/cacheflush.h> +#include <asm/plat-orion/cache-feroceon-l2.h> + + +/* + * Low-level cache maintenance operations. + * + * As well as the regular 'clean/invalidate/flush L2 cache line by + * MVA' instructions, the Feroceon L2 cache controller also features + * 'clean/invalidate L2 range by MVA' operations. + * + * Cache range operations are initiated by writing the start and + * end addresses to successive cp15 registers, and process every + * cache line whose first byte address lies in the inclusive range + * [start:end]. + * + * The cache range operations stall the CPU pipeline until completion. + * + * The range operations require two successive cp15 writes, in + * between which we don't want to be preempted. + */ +static inline void l2_clean_pa(unsigned long addr) +{ + __asm__("mcr p15, 1, %0, c15, c9, 3" : : "r" (addr)); +} + +static inline void l2_clean_mva_range(unsigned long start, unsigned long end) +{ + unsigned long flags; + + /* + * Make sure 'start' and 'end' reference the same page, as + * L2 is PIPT and range operations only do a TLB lookup on + * the start address. + */ + BUG_ON((start ^ end) & ~(PAGE_SIZE - 1)); + + raw_local_irq_save(flags); + __asm__("mcr p15, 1, %0, c15, c9, 4" : : "r" (start)); + __asm__("mcr p15, 1, %0, c15, c9, 5" : : "r" (end)); + raw_local_irq_restore(flags); +} + +static inline void l2_clean_pa_range(unsigned long start, unsigned long end) +{ + l2_clean_mva_range(__phys_to_virt(start), __phys_to_virt(end)); +} + +static inline void l2_clean_inv_pa(unsigned long addr) +{ + __asm__("mcr p15, 1, %0, c15, c10, 3" : : "r" (addr)); +} + +static inline void l2_inv_pa(unsigned long addr) +{ + __asm__("mcr p15, 1, %0, c15, c11, 3" : : "r" (addr)); +} + +static inline void l2_inv_mva_range(unsigned long start, unsigned long end) +{ + unsigned long flags; + + /* + * Make sure 'start' and 'end' reference the same page, as + * L2 is PIPT and range operations only do a TLB lookup on + * the start address. + */ + BUG_ON((start ^ end) & ~(PAGE_SIZE - 1)); + + raw_local_irq_save(flags); + __asm__("mcr p15, 1, %0, c15, c11, 4" : : "r" (start)); + __asm__("mcr p15, 1, %0, c15, c11, 5" : : "r" (end)); + raw_local_irq_restore(flags); +} + +static inline void l2_inv_pa_range(unsigned long start, unsigned long end) +{ + l2_inv_mva_range(__phys_to_virt(start), __phys_to_virt(end)); +} + + +/* + * Linux primitives. + * + * Note that the end addresses passed to Linux primitives are + * noninclusive, while the hardware cache range operations use + * inclusive start and end addresses. + */ +#define CACHE_LINE_SIZE 32 +#define MAX_RANGE_SIZE 1024 + +static int l2_wt_override; + +static unsigned long calc_range_end(unsigned long start, unsigned long end) +{ + unsigned long range_end; + + BUG_ON(start & (CACHE_LINE_SIZE - 1)); + BUG_ON(end & (CACHE_LINE_SIZE - 1)); + + /* + * Try to process all cache lines between 'start' and 'end'. + */ + range_end = end; + + /* + * Limit the number of cache lines processed at once, + * since cache range operations stall the CPU pipeline + * until completion. + */ + if (range_end > start + MAX_RANGE_SIZE) + range_end = start + MAX_RANGE_SIZE; + + /* + * Cache range operations can't straddle a page boundary. + */ + if (range_end > (start | (PAGE_SIZE - 1)) + 1) + range_end = (start | (PAGE_SIZE - 1)) + 1; + + return range_end; +} + +static void feroceon_l2_inv_range(unsigned long start, unsigned long end) +{ + /* + * Clean and invalidate partial first cache line. + */ + if (start & (CACHE_LINE_SIZE - 1)) { + l2_clean_inv_pa(start & ~(CACHE_LINE_SIZE - 1)); + start = (start | (CACHE_LINE_SIZE - 1)) + 1; + } + + /* + * Clean and invalidate partial last cache line. + */ + if (end & (CACHE_LINE_SIZE - 1)) { + l2_clean_inv_pa(end & ~(CACHE_LINE_SIZE - 1)); + end &= ~(CACHE_LINE_SIZE - 1); + } + + /* + * Invalidate all full cache lines between 'start' and 'end'. + */ + while (start != end) { + unsigned long range_end = calc_range_end(start, end); + l2_inv_pa_range(start, range_end - CACHE_LINE_SIZE); + start = range_end; + } + + dsb(); +} + +static void feroceon_l2_clean_range(unsigned long start, unsigned long end) +{ + /* + * If L2 is forced to WT, the L2 will always be clean and we + * don't need to do anything here. + */ + if (!l2_wt_override) { + start &= ~(CACHE_LINE_SIZE - 1); + end = (end + CACHE_LINE_SIZE - 1) & ~(CACHE_LINE_SIZE - 1); + while (start != end) { + unsigned long range_end = calc_range_end(start, end); + l2_clean_pa_range(start, range_end - CACHE_LINE_SIZE); + start = range_end; + } + } + + dsb(); +} + +static void feroceon_l2_flush_range(unsigned long start, unsigned long end) +{ + start &= ~(CACHE_LINE_SIZE - 1); + end = (end + CACHE_LINE_SIZE - 1) & ~(CACHE_LINE_SIZE - 1); + while (start != end) { + unsigned long range_end = calc_range_end(start, end); + if (!l2_wt_override) + l2_clean_pa_range(start, range_end - CACHE_LINE_SIZE); + l2_inv_pa_range(start, range_end - CACHE_LINE_SIZE); + start = range_end; + } + + dsb(); +} + + +/* + * Routines to disable and re-enable the D-cache and I-cache at run + * time. These are necessary because the L2 cache can only be enabled + * or disabled while the L1 Dcache and Icache are both disabled. + */ +static void __init invalidate_and_disable_dcache(void) +{ + u32 cr; + + cr = get_cr(); + if (cr & CR_C) { + unsigned long flags; + + raw_local_irq_save(flags); + flush_cache_all(); + set_cr(cr & ~CR_C); + raw_local_irq_restore(flags); + } +} + +static void __init enable_dcache(void) +{ + u32 cr; + + cr = get_cr(); + if (!(cr & CR_C)) + set_cr(cr | CR_C); +} + +static void __init __invalidate_icache(void) +{ + int dummy; + + __asm__ __volatile__("mcr p15, 0, %0, c7, c5, 0\n" : "=r" (dummy)); +} + +static void __init invalidate_and_disable_icache(void) +{ + u32 cr; + + cr = get_cr(); + if (cr & CR_I) { + set_cr(cr & ~CR_I); + __invalidate_icache(); + } +} + +static void __init enable_icache(void) +{ + u32 cr; + + cr = get_cr(); + if (!(cr & CR_I)) + set_cr(cr | CR_I); +} + +static inline u32 read_extra_features(void) +{ + u32 u; + + __asm__("mrc p15, 1, %0, c15, c1, 0" : "=r" (u)); + + return u; +} + +static inline void write_extra_features(u32 u) +{ + __asm__("mcr p15, 1, %0, c15, c1, 0" : : "r" (u)); +} + +static void __init disable_l2_prefetch(void) +{ + u32 u; + + /* + * Read the CPU Extra Features register and verify that the + * Disable L2 Prefetch bit is set. + */ + u = read_extra_features(); + if (!(u & 0x01000000)) { + printk(KERN_INFO "Feroceon L2: Disabling L2 prefetch.\n"); + write_extra_features(u | 0x01000000); + } +} + +static void __init enable_l2(void) +{ + u32 u; + + u = read_extra_features(); + if (!(u & 0x00400000)) { + printk(KERN_INFO "Feroceon L2: Enabling L2\n"); + + invalidate_and_disable_dcache(); + invalidate_and_disable_icache(); + write_extra_features(u | 0x00400000); + enable_icache(); + enable_dcache(); + } +} + +void __init feroceon_l2_init(int __l2_wt_override) +{ + l2_wt_override = __l2_wt_override; + + disable_l2_prefetch(); + + outer_cache.inv_range = feroceon_l2_inv_range; + outer_cache.clean_range = feroceon_l2_clean_range; + outer_cache.flush_range = feroceon_l2_flush_range; + + enable_l2(); + + printk(KERN_INFO "Feroceon L2: Cache support initialised%s.\n", + l2_wt_override ? ", in WT override mode" : ""); +} diff --git a/arch/arm/mm/fault-armv.c b/arch/arm/mm/fault-armv.c index 44558d5f931..fbfa2605844 100644 --- a/arch/arm/mm/fault-armv.c +++ b/arch/arm/mm/fault-armv.c @@ -144,13 +144,17 @@ void update_mmu_cache(struct vm_area_struct *vma, unsigned long addr, pte_t pte) page = pfn_to_page(pfn); mapping = page_mapping(page); if (mapping) { +#ifndef CONFIG_SMP int dirty = test_and_clear_bit(PG_dcache_dirty, &page->flags); if (dirty) __flush_dcache_page(mapping, page); +#endif if (cache_is_vivt()) make_coherent(mapping, vma, addr, pfn); + else if (vma->vm_flags & VM_EXEC) + __flush_icache_all(); } } diff --git a/arch/arm/mm/flush.c b/arch/arm/mm/flush.c index 9df507d36e0..029ee65fda2 100644 --- a/arch/arm/mm/flush.c +++ b/arch/arm/mm/flush.c @@ -199,6 +199,8 @@ void flush_dcache_page(struct page *page) __flush_dcache_page(mapping, page); if (mapping && cache_is_vivt()) __flush_dcache_aliases(mapping, page); + else if (mapping) + __flush_icache_all(); } } EXPORT_SYMBOL(flush_dcache_page); diff --git a/arch/arm/mm/proc-feroceon.S b/arch/arm/mm/proc-feroceon.S index a02c1712b52..f2e5884c513 100644 --- a/arch/arm/mm/proc-feroceon.S +++ b/arch/arm/mm/proc-feroceon.S @@ -44,11 +44,31 @@ */ #define CACHE_DLINESIZE 32 + .bss + .align 3 +__cache_params_loc: + .space 8 + .text +__cache_params: + .word __cache_params_loc + /* * cpu_feroceon_proc_init() */ ENTRY(cpu_feroceon_proc_init) + mrc p15, 0, r0, c0, c0, 1 @ read cache type register + ldr r1, __cache_params + mov r2, #(16 << 5) + tst r0, #(1 << 16) @ get way + mov r0, r0, lsr #18 @ get cache size order + movne r3, #((4 - 1) << 30) @ 4-way + and r0, r0, #0xf + moveq r3, #0 @ 1-way + mov r2, r2, lsl r0 @ actual cache size + movne r2, r2, lsr #2 @ turned into # of sets + sub r2, r2, #(1 << 5) + stmia r1, {r2, r3} mov pc, lr /* @@ -59,6 +79,13 @@ ENTRY(cpu_feroceon_proc_fin) mov ip, #PSR_F_BIT | PSR_I_BIT | SVC_MODE msr cpsr_c, ip bl feroceon_flush_kern_cache_all + +#if defined(CONFIG_CACHE_FEROCEON_L2) && !defined(CONFIG_L2_CACHE_WRITETHROUGH) + mov r0, #0 + mcr p15, 1, r0, c15, c9, 0 @ clean L2 + mcr p15, 0, r0, c7, c10, 4 @ drain WB +#endif + mrc p15, 0, r0, c1, c0, 0 @ ctrl register bic r0, r0, #0x1000 @ ...i............ bic r0, r0, #0x000e @ ............wca. @@ -117,11 +144,19 @@ ENTRY(feroceon_flush_user_cache_all) */ ENTRY(feroceon_flush_kern_cache_all) mov r2, #VM_EXEC - mov ip, #0 + __flush_whole_cache: -1: mrc p15, 0, r15, c7, c14, 3 @ test,clean,invalidate - bne 1b + ldr r1, __cache_params + ldmia r1, {r1, r3} +1: orr ip, r1, r3 +2: mcr p15, 0, ip, c7, c14, 2 @ clean + invalidate D set/way + subs ip, ip, #(1 << 30) @ next way + bcs 2b + subs r1, r1, #(1 << 5) @ next set + bcs 1b + tst r2, #VM_EXEC + mov ip, #0 mcrne p15, 0, ip, c7, c5, 0 @ invalidate I cache mcrne p15, 0, ip, c7, c10, 4 @ drain WB mov pc, lr @@ -138,7 +173,6 @@ __flush_whole_cache: */ .align 5 ENTRY(feroceon_flush_user_cache_range) - mov ip, #0 sub r3, r1, r0 @ calculate total size cmp r3, #CACHE_DLIMIT bgt __flush_whole_cache @@ -152,6 +186,7 @@ ENTRY(feroceon_flush_user_cache_range) cmp r0, r1 blo 1b tst r2, #VM_EXEC + mov ip, #0 mcrne p15, 0, ip, c7, c10, 4 @ drain WB mov pc, lr @@ -209,6 +244,20 @@ ENTRY(feroceon_flush_kern_dcache_page) mcr p15, 0, r0, c7, c10, 4 @ drain WB mov pc, lr + .align 5 +ENTRY(feroceon_range_flush_kern_dcache_page) + mrs r2, cpsr + add r1, r0, #PAGE_SZ - CACHE_DLINESIZE @ top addr is inclusive + orr r3, r2, #PSR_I_BIT + msr cpsr_c, r3 @ disable interrupts + mcr p15, 5, r0, c15, c15, 0 @ D clean/inv range start + mcr p15, 5, r1, c15, c15, 1 @ D clean/inv range top + msr cpsr_c, r2 @ restore interrupts + mov r0, #0 + mcr p15, 0, r0, c7, c5, 0 @ invalidate I cache + mcr p15, 0, r0, c7, c10, 4 @ drain WB + mov pc, lr + /* * dma_inv_range(start, end) * @@ -225,10 +274,10 @@ ENTRY(feroceon_flush_kern_dcache_page) .align 5 ENTRY(feroceon_dma_inv_range) tst r0, #CACHE_DLINESIZE - 1 + bic r0, r0, #CACHE_DLINESIZE - 1 mcrne p15, 0, r0, c7, c10, 1 @ clean D entry tst r1, #CACHE_DLINESIZE - 1 mcrne p15, 0, r1, c7, c10, 1 @ clean D entry - bic r0, r0, #CACHE_DLINESIZE - 1 1: mcr p15, 0, r0, c7, c6, 1 @ invalidate D entry add r0, r0, #CACHE_DLINESIZE cmp r0, r1 @@ -236,6 +285,22 @@ ENTRY(feroceon_dma_inv_range) mcr p15, 0, r0, c7, c10, 4 @ drain WB mov pc, lr + .align 5 +ENTRY(feroceon_range_dma_inv_range) + mrs r2, cpsr + tst r0, #CACHE_DLINESIZE - 1 + mcrne p15, 0, r0, c7, c10, 1 @ clean D entry + tst r1, #CACHE_DLINESIZE - 1 + mcrne p15, 0, r1, c7, c10, 1 @ clean D entry + cmp r1, r0 + subne r1, r1, #1 @ top address is inclusive + orr r3, r2, #PSR_I_BIT + msr cpsr_c, r3 @ disable interrupts + mcr p15, 5, r0, c15, c14, 0 @ D inv range start + mcr p15, 5, r1, c15, c14, 1 @ D inv range top + msr cpsr_c, r2 @ restore interrupts + mov pc, lr + /* * dma_clean_range(start, end) * @@ -256,6 +321,19 @@ ENTRY(feroceon_dma_clean_range) mcr p15, 0, r0, c7, c10, 4 @ drain WB mov pc, lr + .align 5 +ENTRY(feroceon_range_dma_clean_range) + mrs r2, cpsr + cmp r1, r0 + subne r1, r1, #1 @ top address is inclusive + orr r3, r2, #PSR_I_BIT + msr cpsr_c, r3 @ disable interrupts + mcr p15, 5, r0, c15, c13, 0 @ D clean range start + mcr p15, 5, r1, c15, c13, 1 @ D clean range top + msr cpsr_c, r2 @ restore interrupts + mcr p15, 0, r0, c7, c10, 4 @ drain WB + mov pc, lr + /* * dma_flush_range(start, end) * @@ -274,6 +352,19 @@ ENTRY(feroceon_dma_flush_range) mcr p15, 0, r0, c7, c10, 4 @ drain WB mov pc, lr + .align 5 +ENTRY(feroceon_range_dma_flush_range) + mrs r2, cpsr + cmp r1, r0 + subne r1, r1, #1 @ top address is inclusive + orr r3, r2, #PSR_I_BIT + msr cpsr_c, r3 @ disable interrupts + mcr p15, 5, r0, c15, c15, 0 @ D clean/inv range start + mcr p15, 5, r1, c15, c15, 1 @ D clean/inv range top + msr cpsr_c, r2 @ restore interrupts + mcr p15, 0, r0, c7, c10, 4 @ drain WB + mov pc, lr + ENTRY(feroceon_cache_fns) .long feroceon_flush_kern_cache_all .long feroceon_flush_user_cache_all @@ -285,12 +376,33 @@ ENTRY(feroceon_cache_fns) .long feroceon_dma_clean_range .long feroceon_dma_flush_range +ENTRY(feroceon_range_cache_fns) + .long feroceon_flush_kern_cache_all + .long feroceon_flush_user_cache_all + .long feroceon_flush_user_cache_range + .long feroceon_coherent_kern_range + .long feroceon_coherent_user_range + .long feroceon_range_flush_kern_dcache_page + .long feroceon_range_dma_inv_range + .long feroceon_range_dma_clean_range + .long feroceon_range_dma_flush_range + .align 5 ENTRY(cpu_feroceon_dcache_clean_area) +#if defined(CONFIG_CACHE_FEROCEON_L2) && !defined(CONFIG_L2_CACHE_WRITETHROUGH) + mov r2, r0 + mov r3, r1 +#endif 1: mcr p15, 0, r0, c7, c10, 1 @ clean D entry add r0, r0, #CACHE_DLINESIZE subs r1, r1, #CACHE_DLINESIZE bhi 1b +#if defined(CONFIG_CACHE_FEROCEON_L2) && !defined(CONFIG_L2_CACHE_WRITETHROUGH) +1: mcr p15, 1, r2, c15, c9, 1 @ clean L2 entry + add r2, r2, #CACHE_DLINESIZE + subs r3, r3, #CACHE_DLINESIZE + bhi 1b +#endif mcr p15, 0, r0, c7, c10, 4 @ drain WB mov pc, lr @@ -306,16 +418,25 @@ ENTRY(cpu_feroceon_dcache_clean_area) .align 5 ENTRY(cpu_feroceon_switch_mm) #ifdef CONFIG_MMU - mov ip, #0 -@ && 'Clean & Invalidate whole DCache' -1: mrc p15, 0, r15, c7, c14, 3 @ test,clean,invalidate - bne 1b - mcr p15, 0, ip, c7, c5, 0 @ invalidate I cache - mcr p15, 0, ip, c7, c10, 4 @ drain WB + /* + * Note: we wish to call __flush_whole_cache but we need to preserve + * lr to do so. The only way without touching main memory is to + * use r2 which is normally used to test the VM_EXEC flag, and + * compensate locally for the skipped ops if it is not set. + */ + mov r2, lr @ abuse r2 to preserve lr + bl __flush_whole_cache + @ if r2 contains the VM_EXEC bit then the next 2 ops are done already + tst r2, #VM_EXEC + mcreq p15, 0, ip, c7, c5, 0 @ invalidate I cache + mcreq p15, 0, ip, c7, c10, 4 @ drain WB + mcr p15, 0, r0, c2, c0, 0 @ load page table pointer mcr p15, 0, ip, c8, c7, 0 @ invalidate I & D TLBs -#endif + mov pc, r2 +#else mov pc, lr +#endif /* * cpu_feroceon_set_pte_ext(ptep, pte, ext) @@ -345,6 +466,9 @@ ENTRY(cpu_feroceon_set_pte_ext) str r2, [r0] @ hardware version mov r0, r0 mcr p15, 0, r0, c7, c10, 1 @ clean D entry +#if defined(CONFIG_CACHE_FEROCEON_L2) && !defined(CONFIG_L2_CACHE_WRITETHROUGH) + mcr p15, 1, r0, c15, c9, 1 @ clean L2 entry +#endif mcr p15, 0, r0, c7, c10, 4 @ drain WB #endif mov pc, lr @@ -369,14 +493,15 @@ __feroceon_setup: .size __feroceon_setup, . - __feroceon_setup /* - * R - * .RVI ZFRS BLDP WCAM - * .011 0001 ..11 0101 + * B + * R P + * .RVI UFRS BLDP WCAM + * .011 .001 ..11 0101 * */ .type feroceon_crval, #object feroceon_crval: - crval clear=0x00007f3f, mmuset=0x00003135, ucset=0x00001134 + crval clear=0x0000773f, mmuset=0x00003135, ucset=0x00001134 __INITDATA @@ -414,6 +539,21 @@ cpu_feroceon_name: .asciz "Feroceon" .size cpu_feroceon_name, . - cpu_feroceon_name + .type cpu_88fr531_name, #object +cpu_88fr531_name: + .asciz "Feroceon 88FR531-vd" + .size cpu_88fr531_name, . - cpu_88fr531_name + + .type cpu_88fr571_name, #object +cpu_88fr571_name: + .asciz "Feroceon 88FR571-vd" + .size cpu_88fr571_name, . - cpu_88fr571_name + + .type cpu_88fr131_name, #object +cpu_88fr131_name: + .asciz "Feroceon 88FR131" + .size cpu_88fr131_name, . - cpu_88fr131_name + .align .section ".proc.info.init", #alloc, #execinstr @@ -421,15 +561,15 @@ cpu_feroceon_name: #ifdef CONFIG_CPU_FEROCEON_OLD_ID .type __feroceon_old_id_proc_info,#object __feroceon_old_id_proc_info: - .long 0x41069260 - .long 0xfffffff0 - .long PMD_TYPE_SECT | \ + .long 0x41009260 + .long 0xff00fff0 + .long PMD_TYPE_SECT | \ PMD_SECT_BUFFERABLE | \ PMD_SECT_CACHEABLE | \ PMD_BIT4 | \ PMD_SECT_AP_WRITE | \ PMD_SECT_AP_READ - .long PMD_TYPE_SECT | \ + .long PMD_TYPE_SECT | \ PMD_BIT4 | \ PMD_SECT_AP_WRITE | \ PMD_SECT_AP_READ @@ -445,17 +585,17 @@ __feroceon_old_id_proc_info: .size __feroceon_old_id_proc_info, . - __feroceon_old_id_proc_info #endif - .type __feroceon_proc_info,#object -__feroceon_proc_info: + .type __88fr531_proc_info,#object +__88fr531_proc_info: .long 0x56055310 .long 0xfffffff0 - .long PMD_TYPE_SECT | \ + .long PMD_TYPE_SECT | \ PMD_SECT_BUFFERABLE | \ PMD_SECT_CACHEABLE | \ PMD_BIT4 | \ PMD_SECT_AP_WRITE | \ PMD_SECT_AP_READ - .long PMD_TYPE_SECT | \ + .long PMD_TYPE_SECT | \ PMD_BIT4 | \ PMD_SECT_AP_WRITE | \ PMD_SECT_AP_READ @@ -463,9 +603,59 @@ __feroceon_proc_info: .long cpu_arch_name .long cpu_elf_name .long HWCAP_SWP|HWCAP_HALF|HWCAP_THUMB|HWCAP_FAST_MULT|HWCAP_EDSP - .long cpu_feroceon_name + .long cpu_88fr531_name .long feroceon_processor_functions .long v4wbi_tlb_fns .long feroceon_user_fns .long feroceon_cache_fns - .size __feroceon_proc_info, . - __feroceon_proc_info + .size __88fr531_proc_info, . - __88fr531_proc_info + + .type __88fr571_proc_info,#object +__88fr571_proc_info: + .long 0x56155710 + .long 0xfffffff0 + .long PMD_TYPE_SECT | \ + PMD_SECT_BUFFERABLE | \ + PMD_SECT_CACHEABLE | \ + PMD_BIT4 | \ + PMD_SECT_AP_WRITE | \ + PMD_SECT_AP_READ + .long PMD_TYPE_SECT | \ + PMD_BIT4 | \ + PMD_SECT_AP_WRITE | \ + PMD_SECT_AP_READ + b __feroceon_setup + .long cpu_arch_name + .long cpu_elf_name + .long HWCAP_SWP|HWCAP_HALF|HWCAP_THUMB|HWCAP_FAST_MULT|HWCAP_EDSP + .long cpu_88fr571_name + .long feroceon_processor_functions + .long v4wbi_tlb_fns + .long feroceon_user_fns + .long feroceon_range_cache_fns + .size __88fr571_proc_info, . - __88fr571_proc_info + + .type __88fr131_proc_info,#object +__88fr131_proc_info: + .long 0x56251310 + .long 0xfffffff0 + .long PMD_TYPE_SECT | \ + PMD_SECT_BUFFERABLE | \ + PMD_SECT_CACHEABLE | \ + PMD_BIT4 | \ + PMD_SECT_AP_WRITE | \ + PMD_SECT_AP_READ + .long PMD_TYPE_SECT | \ + PMD_BIT4 | \ + PMD_SECT_AP_WRITE | \ + PMD_SECT_AP_READ + b __feroceon_setup + .long cpu_arch_name + .long cpu_elf_name + .long HWCAP_SWP|HWCAP_HALF|HWCAP_THUMB|HWCAP_FAST_MULT|HWCAP_EDSP + .long cpu_88fr131_name + .long feroceon_processor_functions + .long v4wbi_tlb_fns + .long feroceon_user_fns + .long feroceon_range_cache_fns + .size __88fr131_proc_info, . - __88fr131_proc_info diff --git a/arch/arm/plat-iop/gpio.c b/arch/arm/plat-iop/gpio.c index eda43608341..640e498c12e 100644 --- a/arch/arm/plat-iop/gpio.c +++ b/arch/arm/plat-iop/gpio.c @@ -11,6 +11,10 @@ */ #include <linux/device.h> +#include <linux/init.h> +#include <linux/types.h> +#include <linux/errno.h> +#include <linux/gpio.h> #include <asm/hardware/iop3xx.h> void gpio_line_config(int line, int direction) @@ -46,3 +50,42 @@ void gpio_line_set(int line, int value) local_irq_restore(flags); } EXPORT_SYMBOL(gpio_line_set); + +static int iop3xx_gpio_direction_input(struct gpio_chip *chip, unsigned gpio) +{ + gpio_line_config(gpio, GPIO_IN); + return 0; +} + +static int iop3xx_gpio_direction_output(struct gpio_chip *chip, unsigned gpio, int level) +{ + gpio_line_set(gpio, level); + gpio_line_config(gpio, GPIO_OUT); + return 0; +} + +static int iop3xx_gpio_get_value(struct gpio_chip *chip, unsigned gpio) +{ + return gpio_line_get(gpio); +} + +static void iop3xx_gpio_set_value(struct gpio_chip *chip, unsigned gpio, int value) +{ + gpio_line_set(gpio, value); +} + +static struct gpio_chip iop3xx_chip = { + .label = "iop3xx", + .direction_input = iop3xx_gpio_direction_input, + .get = iop3xx_gpio_get_value, + .direction_output = iop3xx_gpio_direction_output, + .set = iop3xx_gpio_set_value, + .base = 0, + .ngpio = IOP3XX_N_GPIOS, +}; + +static int __init iop3xx_gpio_setup(void) +{ + return gpiochip_add(&iop3xx_chip); +} +arch_initcall(iop3xx_gpio_setup); diff --git a/arch/arm/plat-omap/Makefile b/arch/arm/plat-omap/Makefile index bc639a30d6d..2c4051cc79a 100644 --- a/arch/arm/plat-omap/Makefile +++ b/arch/arm/plat-omap/Makefile @@ -3,7 +3,7 @@ # # Common support -obj-y := common.o sram.o sram-fn.o clock.o devices.o dma.o mux.o gpio.o \ +obj-y := common.o sram.o clock.o devices.o dma.o mux.o gpio.o \ usb.o fb.o obj-m := obj-n := diff --git a/arch/arm/plat-omap/clock.c b/arch/arm/plat-omap/clock.c index 2db5580048d..c2e741de020 100644 --- a/arch/arm/plat-omap/clock.c +++ b/arch/arm/plat-omap/clock.c @@ -1,7 +1,7 @@ /* * linux/arch/arm/plat-omap/clock.c * - * Copyright (C) 2004 - 2005 Nokia corporation + * Copyright (C) 2004 - 2008 Nokia corporation * Written by Tuukka Tikkanen <tuukka.tikkanen@elektrobit.com> * * Modified for omap shared clock framework by Tony Lindgren <tony@atomide.com> @@ -22,6 +22,7 @@ #include <linux/mutex.h> #include <linux/platform_device.h> #include <linux/cpufreq.h> +#include <linux/debugfs.h> #include <asm/io.h> @@ -33,41 +34,6 @@ static DEFINE_SPINLOCK(clockfw_lock); static struct clk_functions *arch_clock; -#ifdef CONFIG_PM_DEBUG - -static void print_parents(struct clk *clk) -{ - struct clk *p; - int printed = 0; - - list_for_each_entry(p, &clocks, node) { - if (p->parent == clk && p->usecount) { - if (!clk->usecount && !printed) { - printk("MISMATCH: %s\n", clk->name); - printed = 1; - } - printk("\t%-15s\n", p->name); - } - } -} - -void clk_print_usecounts(void) -{ - unsigned long flags; - struct clk *p; - - spin_lock_irqsave(&clockfw_lock, flags); - list_for_each_entry(p, &clocks, node) { - if (p->usecount) - printk("%-15s: %d\n", p->name, p->usecount); - print_parents(p); - - } - spin_unlock_irqrestore(&clockfw_lock, flags); -} - -#endif - /*------------------------------------------------------------------------- * Standard clock functions defined in include/linux/clk.h *-------------------------------------------------------------------------*/ @@ -446,3 +412,93 @@ int __init clk_init(struct clk_functions * custom_clocks) return 0; } +#if defined(CONFIG_PM_DEBUG) && defined(CONFIG_DEBUG_FS) +/* + * debugfs support to trace clock tree hierarchy and attributes + */ +static struct dentry *clk_debugfs_root; + +static int clk_debugfs_register_one(struct clk *c) +{ + int err; + struct dentry *d, *child; + struct clk *pa = c->parent; + char s[255]; + char *p = s; + + p += sprintf(p, "%s", c->name); + if (c->id != 0) + sprintf(p, ":%d", c->id); + d = debugfs_create_dir(s, pa ? pa->dent : clk_debugfs_root); + if (IS_ERR(d)) + return PTR_ERR(d); + c->dent = d; + + d = debugfs_create_u8("usecount", S_IRUGO, c->dent, (u8 *)&c->usecount); + if (IS_ERR(d)) { + err = PTR_ERR(d); + goto err_out; + } + d = debugfs_create_u32("rate", S_IRUGO, c->dent, (u32 *)&c->rate); + if (IS_ERR(d)) { + err = PTR_ERR(d); + goto err_out; + } + d = debugfs_create_x32("flags", S_IRUGO, c->dent, (u32 *)&c->flags); + if (IS_ERR(d)) { + err = PTR_ERR(d); + goto err_out; + } + return 0; + +err_out: + d = c->dent; + list_for_each_entry(child, &d->d_subdirs, d_u.d_child) + debugfs_remove(child); + debugfs_remove(c->dent); + return err; +} + +static int clk_debugfs_register(struct clk *c) +{ + int err; + struct clk *pa = c->parent; + + if (pa && !pa->dent) { + err = clk_debugfs_register(pa); + if (err) + return err; + } + + if (!c->dent) { + err = clk_debugfs_register_one(c); + if (err) + return err; + } + return 0; +} + +static int __init clk_debugfs_init(void) +{ + struct clk *c; + struct dentry *d; + int err; + + d = debugfs_create_dir("clock", NULL); + if (IS_ERR(d)) + return PTR_ERR(d); + clk_debugfs_root = d; + + list_for_each_entry(c, &clocks, node) { + err = clk_debugfs_register(c); + if (err) + goto err_out; + } + return 0; +err_out: + debugfs_remove(clk_debugfs_root); /* REVISIT: Cleanup correctly */ + return err; +} +late_initcall(clk_debugfs_init); + +#endif /* defined(CONFIG_PM_DEBUG) && defined(CONFIG_DEBUG_FS) */ diff --git a/arch/arm/plat-omap/common.c b/arch/arm/plat-omap/common.c index bd1cef2c3c1..8d04929a3c7 100644 --- a/arch/arm/plat-omap/common.c +++ b/arch/arm/plat-omap/common.c @@ -26,6 +26,7 @@ #include <asm/io.h> #include <asm/setup.h> +#include <asm/arch/common.h> #include <asm/arch/board.h> #include <asm/arch/control.h> #include <asm/arch/mux.h> @@ -241,30 +242,70 @@ arch_initcall(omap_init_clocksource_32k); /* Global address base setup code */ +#if defined(CONFIG_ARCH_OMAP2) || defined(CONFIG_ARCH_OMAP3) + +static struct omap_globals *omap2_globals; + +static void __init __omap2_set_globals(void) +{ + omap2_set_globals_memory(omap2_globals); + omap2_set_globals_control(omap2_globals); + omap2_set_globals_prcm(omap2_globals); +} + +#endif + #if defined(CONFIG_ARCH_OMAP2420) + +static struct omap_globals omap242x_globals = { + .tap = (__force void __iomem *)OMAP2_IO_ADDRESS(0x48014000), + .sdrc = (__force void __iomem *)OMAP2_IO_ADDRESS(OMAP2420_SDRC_BASE), + .sms = (__force void __iomem *)OMAP2_IO_ADDRESS(OMAP2420_SMS_BASE), + .ctrl = (__force void __iomem *)OMAP2_IO_ADDRESS(OMAP2420_CTRL_BASE), + .prm = (__force void __iomem *)OMAP2_IO_ADDRESS(OMAP2420_PRM_BASE), + .cm = (__force void __iomem *)OMAP2_IO_ADDRESS(OMAP2420_CM_BASE), +}; + void __init omap2_set_globals_242x(void) { - omap2_sdrc_base = OMAP2420_SDRC_BASE; - omap2_sms_base = OMAP2420_SMS_BASE; - omap_ctrl_base_set(OMAP2420_CTRL_BASE); + omap2_globals = &omap242x_globals; + __omap2_set_globals(); } #endif #if defined(CONFIG_ARCH_OMAP2430) + +static struct omap_globals omap243x_globals = { + .tap = (__force void __iomem *)OMAP2_IO_ADDRESS(0x4900a000), + .sdrc = (__force void __iomem *)OMAP2_IO_ADDRESS(OMAP243X_SDRC_BASE), + .sms = (__force void __iomem *)OMAP2_IO_ADDRESS(OMAP243X_SMS_BASE), + .ctrl = (__force void __iomem *)OMAP2_IO_ADDRESS(OMAP243X_CTRL_BASE), + .prm = (__force void __iomem *)OMAP2_IO_ADDRESS(OMAP2430_PRM_BASE), + .cm = (__force void __iomem *)OMAP2_IO_ADDRESS(OMAP2430_CM_BASE), +}; + void __init omap2_set_globals_243x(void) { - omap2_sdrc_base = OMAP243X_SDRC_BASE; - omap2_sms_base = OMAP243X_SMS_BASE; - omap_ctrl_base_set(OMAP243X_CTRL_BASE); + omap2_globals = &omap243x_globals; + __omap2_set_globals(); } #endif #if defined(CONFIG_ARCH_OMAP3430) + +static struct omap_globals omap343x_globals = { + .tap = (__force void __iomem *)OMAP2_IO_ADDRESS(0x4830A000), + .sdrc = (__force void __iomem *)OMAP2_IO_ADDRESS(OMAP343X_SDRC_BASE), + .sms = (__force void __iomem *)OMAP2_IO_ADDRESS(OMAP343X_SMS_BASE), + .ctrl = (__force void __iomem *)OMAP2_IO_ADDRESS(OMAP343X_CTRL_BASE), + .prm = (__force void __iomem *)OMAP2_IO_ADDRESS(OMAP3430_PRM_BASE), + .cm = (__force void __iomem *)OMAP2_IO_ADDRESS(OMAP3430_CM_BASE), +}; + void __init omap2_set_globals_343x(void) { - omap2_sdrc_base = OMAP343X_SDRC_BASE; - omap2_sms_base = OMAP343X_SMS_BASE; - omap_ctrl_base_set(OMAP343X_CTRL_BASE); + omap2_globals = &omap343x_globals; + __omap2_set_globals(); } #endif diff --git a/arch/arm/plat-omap/devices.c b/arch/arm/plat-omap/devices.c index 4a53f9ba6c4..81002b722da 100644 --- a/arch/arm/plat-omap/devices.c +++ b/arch/arm/plat-omap/devices.c @@ -24,6 +24,7 @@ #include <asm/arch/mux.h> #include <asm/arch/gpio.h> #include <asm/arch/menelaus.h> +#include <asm/arch/mcbsp.h> #if defined(CONFIG_OMAP_DSP) || defined(CONFIG_OMAP_DSP_MODULE) @@ -145,6 +146,53 @@ static inline void omap_init_kp(void) {} #endif /*-------------------------------------------------------------------------*/ +#if defined(CONFIG_OMAP_MCBSP) || defined(CONFIG_OMAP_MCBSP_MODULE) + +static struct platform_device **omap_mcbsp_devices; + +void omap_mcbsp_register_board_cfg(struct omap_mcbsp_platform_data *config, + int size) +{ + int i; + + if (size > OMAP_MAX_MCBSP_COUNT) { + printk(KERN_WARNING "Registered too many McBSPs platform_data." + " Using maximum (%d) available.\n", + OMAP_MAX_MCBSP_COUNT); + size = OMAP_MAX_MCBSP_COUNT; + } + + omap_mcbsp_devices = kzalloc(size * sizeof(struct platform_device *), + GFP_KERNEL); + if (!omap_mcbsp_devices) { + printk(KERN_ERR "Could not register McBSP devices\n"); + return; + } + + for (i = 0; i < size; i++) { + struct platform_device *new_mcbsp; + int ret; + + new_mcbsp = platform_device_alloc("omap-mcbsp", i + 1); + if (!new_mcbsp) + continue; + new_mcbsp->dev.platform_data = &config[i]; + ret = platform_device_add(new_mcbsp); + if (ret) { + platform_device_put(new_mcbsp); + continue; + } + omap_mcbsp_devices[i] = new_mcbsp; + } +} + +#else +void omap_mcbsp_register_board_cfg(struct omap_mcbsp_platform_data *config, + int size) +{ } +#endif + +/*-------------------------------------------------------------------------*/ #if defined(CONFIG_MMC_OMAP) || defined(CONFIG_MMC_OMAP_MODULE) diff --git a/arch/arm/plat-omap/dma.c b/arch/arm/plat-omap/dma.c index 39c637b0ffe..fac8e994f58 100644 --- a/arch/arm/plat-omap/dma.c +++ b/arch/arm/plat-omap/dma.c @@ -1,7 +1,7 @@ /* * linux/arch/arm/plat-omap/dma.c * - * Copyright (C) 2003 Nokia Corporation + * Copyright (C) 2003 - 2008 Nokia Corporation * Author: Juha Yrjölä <juha.yrjola@nokia.com> * DMA channel linking for 1610 by Samuel Ortiz <samuel.ortiz@nokia.com> * Graphics DMA and LCD DMA graphics tranformations @@ -25,11 +25,11 @@ #include <linux/errno.h> #include <linux/interrupt.h> #include <linux/irq.h> +#include <linux/io.h> #include <asm/system.h> #include <asm/hardware.h> #include <asm/dma.h> -#include <asm/io.h> #include <asm/arch/tc.h> @@ -43,13 +43,13 @@ enum { DMA_CH_ALLOC_DONE, DMA_CH_PARAMS_SET_DONE, DMA_CH_STARTED, enum { DMA_CHAIN_STARTED, DMA_CHAIN_NOTSTARTED }; #endif -#define OMAP_DMA_ACTIVE 0x01 -#define OMAP_DMA_CCR_EN (1 << 7) +#define OMAP_DMA_ACTIVE 0x01 +#define OMAP_DMA_CCR_EN (1 << 7) #define OMAP2_DMA_CSR_CLEAR_MASK 0xffe -#define OMAP_FUNC_MUX_ARM_BASE (0xfffe1000 + 0xec) +#define OMAP_FUNC_MUX_ARM_BASE (0xfffe1000 + 0xec) -static int enable_1510_mode = 0; +static int enable_1510_mode; struct omap_dma_lch { int next_lch; @@ -57,7 +57,7 @@ struct omap_dma_lch { u16 saved_csr; u16 enabled_irqs; const char *dev_name; - void (* callback)(int lch, u16 ch_status, void *data); + void (*callback)(int lch, u16 ch_status, void *data); void *data; #ifndef CONFIG_ARCH_OMAP1 @@ -72,7 +72,6 @@ struct omap_dma_lch { long flags; }; -#ifndef CONFIG_ARCH_OMAP1 struct dma_link_info { int *linked_dmach_q; int no_of_lchs_linked; @@ -86,7 +85,9 @@ struct dma_link_info { }; -static struct dma_link_info dma_linked_lch[OMAP_LOGICAL_DMA_CH_COUNT]; +static struct dma_link_info *dma_linked_lch; + +#ifndef CONFIG_ARCH_OMAP1 /* Chain handling macros */ #define OMAP_DMA_CHAIN_QINIT(chain_id) \ @@ -119,12 +120,15 @@ static struct dma_link_info dma_linked_lch[OMAP_LOGICAL_DMA_CH_COUNT]; dma_linked_lch[chain_id].q_count++; \ } while (0) #endif + +static int dma_lch_count; static int dma_chan_count; static spinlock_t dma_chan_lock; -static struct omap_dma_lch dma_chan[OMAP_LOGICAL_DMA_CH_COUNT]; +static struct omap_dma_lch *dma_chan; +static void __iomem *omap_dma_base; -static const u8 omap1_dma_irq[OMAP_LOGICAL_DMA_CH_COUNT] = { +static const u8 omap1_dma_irq[OMAP1_LOGICAL_DMA_CH_COUNT] = { INT_DMA_CH0_6, INT_DMA_CH1_7, INT_DMA_CH2_8, INT_DMA_CH3, INT_DMA_CH4, INT_DMA_CH5, INT_1610_DMA_CH6, INT_1610_DMA_CH7, INT_1610_DMA_CH8, INT_1610_DMA_CH9, INT_1610_DMA_CH10, @@ -139,6 +143,24 @@ static inline void omap_enable_channel_irq(int lch); #define REVISIT_24XX() printk(KERN_ERR "FIXME: no %s on 24xx\n", \ __func__); +#define dma_read(reg) \ +({ \ + u32 __val; \ + if (cpu_class_is_omap1()) \ + __val = __raw_readw(omap_dma_base + OMAP1_DMA_##reg); \ + else \ + __val = __raw_readl(omap_dma_base + OMAP_DMA4_##reg); \ + __val; \ +}) + +#define dma_write(val, reg) \ +({ \ + if (cpu_class_is_omap1()) \ + __raw_writew((u16)(val), omap_dma_base + OMAP1_DMA_##reg); \ + else \ + __raw_writel((val), omap_dma_base + OMAP_DMA4_##reg); \ +}) + #ifdef CONFIG_ARCH_OMAP15XX /* Returns 1 if the DMA module is in OMAP1510-compatible mode, 0 otherwise */ int omap_dma_in_1510_mode(void) @@ -173,13 +195,14 @@ static inline void set_gdma_dev(int req, int dev) #define set_gdma_dev(req, dev) do {} while (0) #endif +/* Omap1 only */ static void clear_lch_regs(int lch) { int i; - u32 lch_base = OMAP_DMA_BASE + lch * 0x40; + void __iomem *lch_base = omap_dma_base + OMAP1_DMA_CH_BASE(lch); for (i = 0; i < 0x2c; i += 2) - omap_writew(0, lch_base + i); + __raw_writew(0, lch_base + i); } void omap_set_dma_priority(int lch, int dst_port, int priority) @@ -212,33 +235,49 @@ void omap_set_dma_priority(int lch, int dst_port, int priority) } if (cpu_class_is_omap2()) { + u32 ccr; + + ccr = dma_read(CCR(lch)); if (priority) - OMAP_DMA_CCR_REG(lch) |= (1 << 6); + ccr |= (1 << 6); else - OMAP_DMA_CCR_REG(lch) &= ~(1 << 6); + ccr &= ~(1 << 6); + dma_write(ccr, CCR(lch)); } } +EXPORT_SYMBOL(omap_set_dma_priority); void omap_set_dma_transfer_params(int lch, int data_type, int elem_count, int frame_count, int sync_mode, int dma_trigger, int src_or_dst_synch) { - OMAP_DMA_CSDP_REG(lch) &= ~0x03; - OMAP_DMA_CSDP_REG(lch) |= data_type; + u32 l; + + l = dma_read(CSDP(lch)); + l &= ~0x03; + l |= data_type; + dma_write(l, CSDP(lch)); if (cpu_class_is_omap1()) { - OMAP_DMA_CCR_REG(lch) &= ~(1 << 5); + u16 ccr; + + ccr = dma_read(CCR(lch)); + ccr &= ~(1 << 5); if (sync_mode == OMAP_DMA_SYNC_FRAME) - OMAP_DMA_CCR_REG(lch) |= 1 << 5; + ccr |= 1 << 5; + dma_write(ccr, CCR(lch)); - OMAP1_DMA_CCR2_REG(lch) &= ~(1 << 2); + ccr = dma_read(CCR2(lch)); + ccr &= ~(1 << 2); if (sync_mode == OMAP_DMA_SYNC_BLOCK) - OMAP1_DMA_CCR2_REG(lch) |= 1 << 2; + ccr |= 1 << 2; + dma_write(ccr, CCR2(lch)); } if (cpu_class_is_omap2() && dma_trigger) { - u32 val = OMAP_DMA_CCR_REG(lch); + u32 val; + val = dma_read(CCR(lch)); val &= ~(3 << 19); if (dma_trigger > 63) val |= 1 << 20; @@ -263,12 +302,13 @@ void omap_set_dma_transfer_params(int lch, int data_type, int elem_count, else val &= ~(1 << 24); /* dest synch */ - OMAP_DMA_CCR_REG(lch) = val; + dma_write(val, CCR(lch)); } - OMAP_DMA_CEN_REG(lch) = elem_count; - OMAP_DMA_CFN_REG(lch) = frame_count; + dma_write(elem_count, CEN(lch)); + dma_write(frame_count, CFN(lch)); } +EXPORT_SYMBOL(omap_set_dma_transfer_params); void omap_set_dma_color_mode(int lch, enum omap_dma_color_mode mode, u32 color) { @@ -281,7 +321,9 @@ void omap_set_dma_color_mode(int lch, enum omap_dma_color_mode mode, u32 color) return; } - w = OMAP1_DMA_CCR2_REG(lch) & ~0x03; + w = dma_read(CCR2(lch)); + w &= ~0x03; + switch (mode) { case OMAP_DMA_CONSTANT_FILL: w |= 0x01; @@ -294,52 +336,81 @@ void omap_set_dma_color_mode(int lch, enum omap_dma_color_mode mode, u32 color) default: BUG(); } - OMAP1_DMA_CCR2_REG(lch) = w; + dma_write(w, CCR2(lch)); - w = OMAP1_DMA_LCH_CTRL_REG(lch) & ~0x0f; + w = dma_read(LCH_CTRL(lch)); + w &= ~0x0f; /* Default is channel type 2D */ if (mode) { - OMAP1_DMA_COLOR_L_REG(lch) = (u16)color; - OMAP1_DMA_COLOR_U_REG(lch) = (u16)(color >> 16); + dma_write((u16)color, COLOR_L(lch)); + dma_write((u16)(color >> 16), COLOR_U(lch)); w |= 1; /* Channel type G */ } - OMAP1_DMA_LCH_CTRL_REG(lch) = w; + dma_write(w, LCH_CTRL(lch)); } +EXPORT_SYMBOL(omap_set_dma_color_mode); void omap_set_dma_write_mode(int lch, enum omap_dma_write_mode mode) { if (cpu_class_is_omap2()) { - OMAP_DMA_CSDP_REG(lch) &= ~(0x3 << 16); - OMAP_DMA_CSDP_REG(lch) |= (mode << 16); + u32 csdp; + + csdp = dma_read(CSDP(lch)); + csdp &= ~(0x3 << 16); + csdp |= (mode << 16); + dma_write(csdp, CSDP(lch)); + } +} +EXPORT_SYMBOL(omap_set_dma_write_mode); + +void omap_set_dma_channel_mode(int lch, enum omap_dma_channel_mode mode) +{ + if (cpu_class_is_omap1() && !cpu_is_omap15xx()) { + u32 l; + + l = dma_read(LCH_CTRL(lch)); + l &= ~0x7; + l |= mode; + dma_write(l, LCH_CTRL(lch)); } } +EXPORT_SYMBOL(omap_set_dma_channel_mode); /* Note that src_port is only for omap1 */ void omap_set_dma_src_params(int lch, int src_port, int src_amode, unsigned long src_start, int src_ei, int src_fi) { + u32 l; + if (cpu_class_is_omap1()) { - OMAP_DMA_CSDP_REG(lch) &= ~(0x1f << 2); - OMAP_DMA_CSDP_REG(lch) |= src_port << 2; + u16 w; + + w = dma_read(CSDP(lch)); + w &= ~(0x1f << 2); + w |= src_port << 2; + dma_write(w, CSDP(lch)); } - OMAP_DMA_CCR_REG(lch) &= ~(0x03 << 12); - OMAP_DMA_CCR_REG(lch) |= src_amode << 12; + l = dma_read(CCR(lch)); + l &= ~(0x03 << 12); + l |= src_amode << 12; + dma_write(l, CCR(lch)); if (cpu_class_is_omap1()) { - OMAP1_DMA_CSSA_U_REG(lch) = src_start >> 16; - OMAP1_DMA_CSSA_L_REG(lch) = src_start; + dma_write(src_start >> 16, CSSA_U(lch)); + dma_write((u16)src_start, CSSA_L(lch)); } if (cpu_class_is_omap2()) - OMAP2_DMA_CSSA_REG(lch) = src_start; + dma_write(src_start, CSSA(lch)); - OMAP_DMA_CSEI_REG(lch) = src_ei; - OMAP_DMA_CSFI_REG(lch) = src_fi; + dma_write(src_ei, CSEI(lch)); + dma_write(src_fi, CSFI(lch)); } +EXPORT_SYMBOL(omap_set_dma_src_params); -void omap_set_dma_params(int lch, struct omap_dma_channel_params * params) +void omap_set_dma_params(int lch, struct omap_dma_channel_params *params) { omap_set_dma_transfer_params(lch, params->data_type, params->elem_count, params->frame_count, @@ -356,28 +427,37 @@ void omap_set_dma_params(int lch, struct omap_dma_channel_params * params) omap_dma_set_prio_lch(lch, params->read_prio, params->write_prio); } +EXPORT_SYMBOL(omap_set_dma_params); void omap_set_dma_src_index(int lch, int eidx, int fidx) { - if (cpu_class_is_omap2()) { - REVISIT_24XX(); + if (cpu_class_is_omap2()) return; - } - OMAP_DMA_CSEI_REG(lch) = eidx; - OMAP_DMA_CSFI_REG(lch) = fidx; + + dma_write(eidx, CSEI(lch)); + dma_write(fidx, CSFI(lch)); } +EXPORT_SYMBOL(omap_set_dma_src_index); void omap_set_dma_src_data_pack(int lch, int enable) { - OMAP_DMA_CSDP_REG(lch) &= ~(1 << 6); + u32 l; + + l = dma_read(CSDP(lch)); + l &= ~(1 << 6); if (enable) - OMAP_DMA_CSDP_REG(lch) |= (1 << 6); + l |= (1 << 6); + dma_write(l, CSDP(lch)); } +EXPORT_SYMBOL(omap_set_dma_src_data_pack); void omap_set_dma_src_burst_mode(int lch, enum omap_dma_burst_mode burst_mode) { unsigned int burst = 0; - OMAP_DMA_CSDP_REG(lch) &= ~(0x03 << 7); + u32 l; + + l = dma_read(CSDP(lch)); + l &= ~(0x03 << 7); switch (burst_mode) { case OMAP_DMA_DATA_BURST_DIS: @@ -408,55 +488,73 @@ void omap_set_dma_src_burst_mode(int lch, enum omap_dma_burst_mode burst_mode) default: BUG(); } - OMAP_DMA_CSDP_REG(lch) |= (burst << 7); + + l |= (burst << 7); + dma_write(l, CSDP(lch)); } +EXPORT_SYMBOL(omap_set_dma_src_burst_mode); /* Note that dest_port is only for OMAP1 */ void omap_set_dma_dest_params(int lch, int dest_port, int dest_amode, unsigned long dest_start, int dst_ei, int dst_fi) { + u32 l; + if (cpu_class_is_omap1()) { - OMAP_DMA_CSDP_REG(lch) &= ~(0x1f << 9); - OMAP_DMA_CSDP_REG(lch) |= dest_port << 9; + l = dma_read(CSDP(lch)); + l &= ~(0x1f << 9); + l |= dest_port << 9; + dma_write(l, CSDP(lch)); } - OMAP_DMA_CCR_REG(lch) &= ~(0x03 << 14); - OMAP_DMA_CCR_REG(lch) |= dest_amode << 14; + l = dma_read(CCR(lch)); + l &= ~(0x03 << 14); + l |= dest_amode << 14; + dma_write(l, CCR(lch)); if (cpu_class_is_omap1()) { - OMAP1_DMA_CDSA_U_REG(lch) = dest_start >> 16; - OMAP1_DMA_CDSA_L_REG(lch) = dest_start; + dma_write(dest_start >> 16, CDSA_U(lch)); + dma_write(dest_start, CDSA_L(lch)); } if (cpu_class_is_omap2()) - OMAP2_DMA_CDSA_REG(lch) = dest_start; + dma_write(dest_start, CDSA(lch)); - OMAP_DMA_CDEI_REG(lch) = dst_ei; - OMAP_DMA_CDFI_REG(lch) = dst_fi; + dma_write(dst_ei, CDEI(lch)); + dma_write(dst_fi, CDFI(lch)); } +EXPORT_SYMBOL(omap_set_dma_dest_params); void omap_set_dma_dest_index(int lch, int eidx, int fidx) { - if (cpu_class_is_omap2()) { - REVISIT_24XX(); + if (cpu_class_is_omap2()) return; - } - OMAP_DMA_CDEI_REG(lch) = eidx; - OMAP_DMA_CDFI_REG(lch) = fidx; + + dma_write(eidx, CDEI(lch)); + dma_write(fidx, CDFI(lch)); } +EXPORT_SYMBOL(omap_set_dma_dest_index); void omap_set_dma_dest_data_pack(int lch, int enable) { - OMAP_DMA_CSDP_REG(lch) &= ~(1 << 13); + u32 l; + + l = dma_read(CSDP(lch)); + l &= ~(1 << 13); if (enable) - OMAP_DMA_CSDP_REG(lch) |= 1 << 13; + l |= 1 << 13; + dma_write(l, CSDP(lch)); } +EXPORT_SYMBOL(omap_set_dma_dest_data_pack); void omap_set_dma_dest_burst_mode(int lch, enum omap_dma_burst_mode burst_mode) { unsigned int burst = 0; - OMAP_DMA_CSDP_REG(lch) &= ~(0x03 << 14); + u32 l; + + l = dma_read(CSDP(lch)); + l &= ~(0x03 << 14); switch (burst_mode) { case OMAP_DMA_DATA_BURST_DIS: @@ -486,8 +584,10 @@ void omap_set_dma_dest_burst_mode(int lch, enum omap_dma_burst_mode burst_mode) BUG(); return; } - OMAP_DMA_CSDP_REG(lch) |= (burst << 14); + l |= (burst << 14); + dma_write(l, CSDP(lch)); } +EXPORT_SYMBOL(omap_set_dma_dest_burst_mode); static inline void omap_enable_channel_irq(int lch) { @@ -495,62 +595,74 @@ static inline void omap_enable_channel_irq(int lch) /* Clear CSR */ if (cpu_class_is_omap1()) - status = OMAP_DMA_CSR_REG(lch); + status = dma_read(CSR(lch)); else if (cpu_class_is_omap2()) - OMAP_DMA_CSR_REG(lch) = OMAP2_DMA_CSR_CLEAR_MASK; + dma_write(OMAP2_DMA_CSR_CLEAR_MASK, CSR(lch)); /* Enable some nice interrupts. */ - OMAP_DMA_CICR_REG(lch) = dma_chan[lch].enabled_irqs; + dma_write(dma_chan[lch].enabled_irqs, CICR(lch)); } static void omap_disable_channel_irq(int lch) { if (cpu_class_is_omap2()) - OMAP_DMA_CICR_REG(lch) = 0; + dma_write(0, CICR(lch)); } void omap_enable_dma_irq(int lch, u16 bits) { dma_chan[lch].enabled_irqs |= bits; } +EXPORT_SYMBOL(omap_enable_dma_irq); void omap_disable_dma_irq(int lch, u16 bits) { dma_chan[lch].enabled_irqs &= ~bits; } +EXPORT_SYMBOL(omap_disable_dma_irq); static inline void enable_lnk(int lch) { + u32 l; + + l = dma_read(CLNK_CTRL(lch)); + if (cpu_class_is_omap1()) - OMAP_DMA_CLNK_CTRL_REG(lch) &= ~(1 << 14); + l &= ~(1 << 14); /* Set the ENABLE_LNK bits */ if (dma_chan[lch].next_lch != -1) - OMAP_DMA_CLNK_CTRL_REG(lch) = - dma_chan[lch].next_lch | (1 << 15); + l = dma_chan[lch].next_lch | (1 << 15); #ifndef CONFIG_ARCH_OMAP1 - if (dma_chan[lch].next_linked_ch != -1) - OMAP_DMA_CLNK_CTRL_REG(lch) = - dma_chan[lch].next_linked_ch | (1 << 15); + if (cpu_class_is_omap2()) + if (dma_chan[lch].next_linked_ch != -1) + l = dma_chan[lch].next_linked_ch | (1 << 15); #endif + + dma_write(l, CLNK_CTRL(lch)); } static inline void disable_lnk(int lch) { + u32 l; + + l = dma_read(CLNK_CTRL(lch)); + /* Disable interrupts */ if (cpu_class_is_omap1()) { - OMAP_DMA_CICR_REG(lch) = 0; + dma_write(0, CICR(lch)); /* Set the STOP_LNK bit */ - OMAP_DMA_CLNK_CTRL_REG(lch) |= 1 << 14; + l |= 1 << 14; } if (cpu_class_is_omap2()) { omap_disable_channel_irq(lch); /* Clear the ENABLE_LNK bit */ - OMAP_DMA_CLNK_CTRL_REG(lch) &= ~(1 << 15); + l &= ~(1 << 15); } + dma_write(l, CLNK_CTRL(lch)); dma_chan[lch].flags &= ~OMAP_DMA_ACTIVE; } @@ -561,13 +673,13 @@ static inline void omap2_enable_irq_lch(int lch) if (!cpu_class_is_omap2()) return; - val = omap_readl(OMAP_DMA4_IRQENABLE_L0); + val = dma_read(IRQENABLE_L0); val |= 1 << lch; - omap_writel(val, OMAP_DMA4_IRQENABLE_L0); + dma_write(val, IRQENABLE_L0); } int omap_request_dma(int dev_id, const char *dev_name, - void (* callback)(int lch, u16 ch_status, void *data), + void (*callback)(int lch, u16 ch_status, void *data), void *data, int *dma_ch_out) { int ch, free_ch = -1; @@ -600,10 +712,14 @@ int omap_request_dma(int dev_id, const char *dev_name, chan->dev_name = dev_name; chan->callback = callback; chan->data = data; + #ifndef CONFIG_ARCH_OMAP1 - chan->chain_id = -1; - chan->next_linked_ch = -1; + if (cpu_class_is_omap2()) { + chan->chain_id = -1; + chan->next_linked_ch = -1; + } #endif + chan->enabled_irqs = OMAP_DMA_DROP_IRQ | OMAP_DMA_BLOCK_IRQ; if (cpu_class_is_omap1()) @@ -618,26 +734,28 @@ int omap_request_dma(int dev_id, const char *dev_name, set_gdma_dev(free_ch + 1, dev_id); dev_id = free_ch + 1; } - /* Disable the 1510 compatibility mode and set the sync device - * id. */ - OMAP_DMA_CCR_REG(free_ch) = dev_id | (1 << 10); + /* + * Disable the 1510 compatibility mode and set the sync device + * id. + */ + dma_write(dev_id | (1 << 10), CCR(free_ch)); } else if (cpu_is_omap730() || cpu_is_omap15xx()) { - OMAP_DMA_CCR_REG(free_ch) = dev_id; + dma_write(dev_id, CCR(free_ch)); } if (cpu_class_is_omap2()) { omap2_enable_irq_lch(free_ch); - omap_enable_channel_irq(free_ch); /* Clear the CSR register and IRQ status register */ - OMAP_DMA_CSR_REG(free_ch) = OMAP2_DMA_CSR_CLEAR_MASK; - omap_writel(1 << free_ch, OMAP_DMA4_IRQSTATUS_L0); + dma_write(OMAP2_DMA_CSR_CLEAR_MASK, CSR(free_ch)); + dma_write(1 << free_ch, IRQSTATUS_L0); } *dma_ch_out = free_ch; return 0; } +EXPORT_SYMBOL(omap_request_dma); void omap_free_dma(int lch) { @@ -645,11 +763,12 @@ void omap_free_dma(int lch) spin_lock_irqsave(&dma_chan_lock, flags); if (dma_chan[lch].dev_id == -1) { - printk("omap_dma: trying to free nonallocated DMA channel %d\n", + pr_err("omap_dma: trying to free unallocated DMA channel %d\n", lch); spin_unlock_irqrestore(&dma_chan_lock, flags); return; } + dma_chan[lch].dev_id = -1; dma_chan[lch].next_lch = -1; dma_chan[lch].callback = NULL; @@ -657,30 +776,31 @@ void omap_free_dma(int lch) if (cpu_class_is_omap1()) { /* Disable all DMA interrupts for the channel. */ - OMAP_DMA_CICR_REG(lch) = 0; + dma_write(0, CICR(lch)); /* Make sure the DMA transfer is stopped. */ - OMAP_DMA_CCR_REG(lch) = 0; + dma_write(0, CCR(lch)); } if (cpu_class_is_omap2()) { u32 val; /* Disable interrupts */ - val = omap_readl(OMAP_DMA4_IRQENABLE_L0); + val = dma_read(IRQENABLE_L0); val &= ~(1 << lch); - omap_writel(val, OMAP_DMA4_IRQENABLE_L0); + dma_write(val, IRQENABLE_L0); /* Clear the CSR register and IRQ status register */ - OMAP_DMA_CSR_REG(lch) = OMAP2_DMA_CSR_CLEAR_MASK; - omap_writel(1 << lch, OMAP_DMA4_IRQSTATUS_L0); + dma_write(OMAP2_DMA_CSR_CLEAR_MASK, CSR(lch)); + dma_write(1 << lch, IRQSTATUS_L0); /* Disable all DMA interrupts for the channel. */ - OMAP_DMA_CICR_REG(lch) = 0; + dma_write(0, CICR(lch)); /* Make sure the DMA transfer is stopped. */ - OMAP_DMA_CCR_REG(lch) = 0; + dma_write(0, CCR(lch)); omap_clear_dma(lch); } } +EXPORT_SYMBOL(omap_free_dma); /** * @brief omap_dma_set_global_params : Set global priority settings for dma @@ -708,7 +828,7 @@ omap_dma_set_global_params(int arb_rate, int max_fifo_depth, int tparams) reg = (arb_rate & 0xff) << 16; reg |= (0xff & max_fifo_depth); - omap_writel(reg, OMAP_DMA4_GCR_REG); + dma_write(reg, GCR); } EXPORT_SYMBOL(omap_dma_set_global_params); @@ -725,20 +845,21 @@ int omap_dma_set_prio_lch(int lch, unsigned char read_prio, unsigned char write_prio) { - u32 w; + u32 l; - if (unlikely((lch < 0 || lch >= OMAP_LOGICAL_DMA_CH_COUNT))) { + if (unlikely((lch < 0 || lch >= dma_lch_count))) { printk(KERN_ERR "Invalid channel id\n"); return -EINVAL; } - w = OMAP_DMA_CCR_REG(lch); - w &= ~((1 << 6) | (1 << 26)); + l = dma_read(CCR(lch)); + l &= ~((1 << 6) | (1 << 26)); if (cpu_is_omap2430() || cpu_is_omap34xx()) - w |= ((read_prio & 0x1) << 6) | ((write_prio & 0x1) << 26); + l |= ((read_prio & 0x1) << 6) | ((write_prio & 0x1) << 26); else - w |= ((read_prio & 0x1) << 6); + l |= ((read_prio & 0x1) << 6); + + dma_write(l, CCR(lch)); - OMAP_DMA_CCR_REG(lch) = w; return 0; } EXPORT_SYMBOL(omap_dma_set_prio_lch); @@ -754,28 +875,34 @@ void omap_clear_dma(int lch) local_irq_save(flags); if (cpu_class_is_omap1()) { - int status; - OMAP_DMA_CCR_REG(lch) &= ~OMAP_DMA_CCR_EN; + u32 l; + + l = dma_read(CCR(lch)); + l &= ~OMAP_DMA_CCR_EN; + dma_write(l, CCR(lch)); /* Clear pending interrupts */ - status = OMAP_DMA_CSR_REG(lch); + l = dma_read(CSR(lch)); } if (cpu_class_is_omap2()) { int i; - u32 lch_base = OMAP_DMA4_BASE + lch * 0x60 + 0x80; + void __iomem *lch_base = omap_dma_base + OMAP_DMA4_CH_BASE(lch); for (i = 0; i < 0x44; i += 4) - omap_writel(0, lch_base + i); + __raw_writel(0, lch_base + i); } local_irq_restore(flags); } +EXPORT_SYMBOL(omap_clear_dma); void omap_start_dma(int lch) { + u32 l; + if (!omap_dma_in_1510_mode() && dma_chan[lch].next_lch != -1) { int next_lch, cur_lch; - char dma_chan_link_map[OMAP_LOGICAL_DMA_CH_COUNT]; + char dma_chan_link_map[OMAP_DMA4_LOGICAL_DMA_CH_COUNT]; dma_chan_link_map[lch] = 1; /* Set the link register of the first channel */ @@ -799,27 +926,34 @@ void omap_start_dma(int lch) } while (next_lch != -1); } else if (cpu_class_is_omap2()) { /* Errata: Need to write lch even if not using chaining */ - OMAP_DMA_CLNK_CTRL_REG(lch) = lch; + dma_write(lch, CLNK_CTRL(lch)); } omap_enable_channel_irq(lch); - /* Errata: On ES2.0 BUFFERING disable must be set. - * This will always fail on ES1.0 */ - if (cpu_is_omap24xx()) { - OMAP_DMA_CCR_REG(lch) |= OMAP_DMA_CCR_EN; - } + l = dma_read(CCR(lch)); + + /* + * Errata: On ES2.0 BUFFERING disable must be set. + * This will always fail on ES1.0 + */ + if (cpu_is_omap24xx()) + l |= OMAP_DMA_CCR_EN; - OMAP_DMA_CCR_REG(lch) |= OMAP_DMA_CCR_EN; + l |= OMAP_DMA_CCR_EN; + dma_write(l, CCR(lch)); dma_chan[lch].flags |= OMAP_DMA_ACTIVE; } +EXPORT_SYMBOL(omap_start_dma); void omap_stop_dma(int lch) { + u32 l; + if (!omap_dma_in_1510_mode() && dma_chan[lch].next_lch != -1) { int next_lch, cur_lch = lch; - char dma_chan_link_map[OMAP_LOGICAL_DMA_CH_COUNT]; + char dma_chan_link_map[OMAP_DMA4_LOGICAL_DMA_CH_COUNT]; memset(dma_chan_link_map, 0, sizeof(dma_chan_link_map)); do { @@ -840,18 +974,22 @@ void omap_stop_dma(int lch) /* Disable all interrupts on the channel */ if (cpu_class_is_omap1()) - OMAP_DMA_CICR_REG(lch) = 0; + dma_write(0, CICR(lch)); + + l = dma_read(CCR(lch)); + l &= ~OMAP_DMA_CCR_EN; + dma_write(l, CCR(lch)); - OMAP_DMA_CCR_REG(lch) &= ~OMAP_DMA_CCR_EN; dma_chan[lch].flags &= ~OMAP_DMA_ACTIVE; } +EXPORT_SYMBOL(omap_stop_dma); /* * Allows changing the DMA callback function or data. This may be needed if * the driver shares a single DMA channel for multiple dma triggers. */ int omap_set_dma_callback(int lch, - void (* callback)(int lch, u16 ch_status, void *data), + void (*callback)(int lch, u16 ch_status, void *data), void *data) { unsigned long flags; @@ -871,6 +1009,7 @@ int omap_set_dma_callback(int lch, return 0; } +EXPORT_SYMBOL(omap_set_dma_callback); /* * Returns current physical source address for the given DMA channel. @@ -884,15 +1023,24 @@ dma_addr_t omap_get_dma_src_pos(int lch) { dma_addr_t offset = 0; - if (cpu_class_is_omap1()) - offset = (dma_addr_t) (OMAP1_DMA_CSSA_L_REG(lch) | - (OMAP1_DMA_CSSA_U_REG(lch) << 16)); + if (cpu_is_omap15xx()) + offset = dma_read(CPC(lch)); + else + offset = dma_read(CSAC(lch)); - if (cpu_class_is_omap2()) - offset = OMAP_DMA_CSAC_REG(lch); + /* + * omap 3.2/3.3 erratum: sometimes 0 is returned if CSAC/CDAC is + * read before the DMA controller finished disabling the channel. + */ + if (!cpu_is_omap15xx() && offset == 0) + offset = dma_read(CSAC(lch)); + + if (cpu_class_is_omap1()) + offset |= (dma_read(CSSA_U(lch)) << 16); return offset; } +EXPORT_SYMBOL(omap_get_dma_src_pos); /* * Returns current physical destination address for the given DMA channel. @@ -906,25 +1054,30 @@ dma_addr_t omap_get_dma_dst_pos(int lch) { dma_addr_t offset = 0; - if (cpu_class_is_omap1()) - offset = (dma_addr_t) (OMAP1_DMA_CDSA_L_REG(lch) | - (OMAP1_DMA_CDSA_U_REG(lch) << 16)); + if (cpu_is_omap15xx()) + offset = dma_read(CPC(lch)); + else + offset = dma_read(CDAC(lch)); - if (cpu_class_is_omap2()) - offset = OMAP_DMA_CDAC_REG(lch); + /* + * omap 3.2/3.3 erratum: sometimes 0 is returned if CSAC/CDAC is + * read before the DMA controller finished disabling the channel. + */ + if (!cpu_is_omap15xx() && offset == 0) + offset = dma_read(CDAC(lch)); + + if (cpu_class_is_omap1()) + offset |= (dma_read(CDSA_U(lch)) << 16); return offset; } +EXPORT_SYMBOL(omap_get_dma_dst_pos); -/* - * Returns current source transfer counting for the given DMA channel. - * Can be used to monitor the progress of a transfer inside a block. - * It must be called with disabled interrupts. - */ -int omap_get_dma_src_addr_counter(int lch) +int omap_get_dma_active_status(int lch) { - return (dma_addr_t) OMAP_DMA_CSAC_REG(lch); + return (dma_read(CCR(lch)) & OMAP_DMA_CCR_EN) != 0; } +EXPORT_SYMBOL(omap_get_dma_active_status); int omap_dma_running(void) { @@ -936,7 +1089,7 @@ int omap_dma_running(void) return 1; for (lch = 0; lch < dma_chan_count; lch++) - if (OMAP_DMA_CCR_REG(lch) & OMAP_DMA_CCR_EN) + if (dma_read(CCR(lch)) & OMAP_DMA_CCR_EN) return 1; return 0; @@ -947,7 +1100,7 @@ int omap_dma_running(void) * For this DMA link to start, you still need to start (see omap_start_dma) * the first one. That will fire up the entire queue. */ -void omap_dma_link_lch (int lch_head, int lch_queue) +void omap_dma_link_lch(int lch_head, int lch_queue) { if (omap_dma_in_1510_mode()) { printk(KERN_ERR "DMA linking is not supported in 1510 mode\n"); @@ -964,11 +1117,12 @@ void omap_dma_link_lch (int lch_head, int lch_queue) dma_chan[lch_head].next_lch = lch_queue; } +EXPORT_SYMBOL(omap_dma_link_lch); /* * Once the DMA queue is stopped, we can destroy it. */ -void omap_dma_unlink_lch (int lch_head, int lch_queue) +void omap_dma_unlink_lch(int lch_head, int lch_queue) { if (omap_dma_in_1510_mode()) { printk(KERN_ERR "DMA linking is not supported in 1510 mode\n"); @@ -983,7 +1137,6 @@ void omap_dma_unlink_lch (int lch_head, int lch_queue) dump_stack(); } - if ((dma_chan[lch_head].flags & OMAP_DMA_ACTIVE) || (dma_chan[lch_head].flags & OMAP_DMA_ACTIVE)) { printk(KERN_ERR "omap_dma: You need to stop the DMA channels " @@ -993,12 +1146,15 @@ void omap_dma_unlink_lch (int lch_head, int lch_queue) dma_chan[lch_head].next_lch = -1; } +EXPORT_SYMBOL(omap_dma_unlink_lch); + +/*----------------------------------------------------------------------------*/ #ifndef CONFIG_ARCH_OMAP1 /* Create chain of DMA channesls */ static void create_dma_lch_chain(int lch_head, int lch_queue) { - u32 w; + u32 l; /* Check if this is the first link in chain */ if (dma_chan[lch_head].next_linked_ch == -1) { @@ -1018,15 +1174,15 @@ static void create_dma_lch_chain(int lch_head, int lch_queue) lch_queue; } - w = OMAP_DMA_CLNK_CTRL_REG(lch_head); - w &= ~(0x1f); - w |= lch_queue; - OMAP_DMA_CLNK_CTRL_REG(lch_head) = w; + l = dma_read(CLNK_CTRL(lch_head)); + l &= ~(0x1f); + l |= lch_queue; + dma_write(l, CLNK_CTRL(lch_head)); - w = OMAP_DMA_CLNK_CTRL_REG(lch_queue); - w &= ~(0x1f); - w |= (dma_chan[lch_queue].next_linked_ch); - OMAP_DMA_CLNK_CTRL_REG(lch_queue) = w; + l = dma_read(CLNK_CTRL(lch_queue)); + l &= ~(0x1f); + l |= (dma_chan[lch_queue].next_linked_ch); + dma_write(l, CLNK_CTRL(lch_queue)); } /** @@ -1061,7 +1217,7 @@ int omap_request_dma_chain(int dev_id, const char *dev_name, } if (unlikely((no_of_chans < 1 - || no_of_chans > OMAP_LOGICAL_DMA_CH_COUNT))) { + || no_of_chans > dma_lch_count))) { printk(KERN_ERR "Invalid Number of channels requested\n"); return -EINVAL; } @@ -1116,6 +1272,7 @@ int omap_request_dma_chain(int dev_id, const char *dev_name, for (i = 0; i < (no_of_chans - 1); i++) create_dma_lch_chain(channels[i], channels[i + 1]); } + return 0; } EXPORT_SYMBOL(omap_request_dma_chain); @@ -1138,7 +1295,7 @@ int omap_modify_dma_chain_params(int chain_id, /* Check for input params */ if (unlikely((chain_id < 0 - || chain_id >= OMAP_LOGICAL_DMA_CH_COUNT))) { + || chain_id >= dma_lch_count))) { printk(KERN_ERR "Invalid chain id\n"); return -EINVAL; } @@ -1158,6 +1315,7 @@ int omap_modify_dma_chain_params(int chain_id, */ omap_set_dma_params(channels[i], ¶ms); } + return 0; } EXPORT_SYMBOL(omap_modify_dma_chain_params); @@ -1176,7 +1334,7 @@ int omap_free_dma_chain(int chain_id) u32 i; /* Check for input params */ - if (unlikely((chain_id < 0 || chain_id >= OMAP_LOGICAL_DMA_CH_COUNT))) { + if (unlikely((chain_id < 0 || chain_id >= dma_lch_count))) { printk(KERN_ERR "Invalid chain id\n"); return -EINVAL; } @@ -1201,6 +1359,7 @@ int omap_free_dma_chain(int chain_id) dma_linked_lch[chain_id].linked_dmach_q = NULL; dma_linked_lch[chain_id].chain_mode = -1; dma_linked_lch[chain_id].chain_state = -1; + return (0); } EXPORT_SYMBOL(omap_free_dma_chain); @@ -1216,7 +1375,7 @@ EXPORT_SYMBOL(omap_free_dma_chain); int omap_dma_chain_status(int chain_id) { /* Check for input params */ - if (unlikely((chain_id < 0 || chain_id >= OMAP_LOGICAL_DMA_CH_COUNT))) { + if (unlikely((chain_id < 0 || chain_id >= dma_lch_count))) { printk(KERN_ERR "Invalid chain id\n"); return -EINVAL; } @@ -1231,6 +1390,7 @@ int omap_dma_chain_status(int chain_id) if (OMAP_DMA_CHAIN_QEMPTY(chain_id)) return OMAP_DMA_CHAIN_INACTIVE; + return OMAP_DMA_CHAIN_ACTIVE; } EXPORT_SYMBOL(omap_dma_chain_status); @@ -1253,11 +1413,13 @@ int omap_dma_chain_a_transfer(int chain_id, int src_start, int dest_start, int elem_count, int frame_count, void *callbk_data) { int *channels; - u32 w, lch; + u32 l, lch; int start_dma = 0; - /* if buffer size is less than 1 then there is - * no use of starting the chain */ + /* + * if buffer size is less than 1 then there is + * no use of starting the chain + */ if (elem_count < 1) { printk(KERN_ERR "Invalid buffer size\n"); return -EINVAL; @@ -1265,7 +1427,7 @@ int omap_dma_chain_a_transfer(int chain_id, int src_start, int dest_start, /* Check for input params */ if (unlikely((chain_id < 0 - || chain_id >= OMAP_LOGICAL_DMA_CH_COUNT))) { + || chain_id >= dma_lch_count))) { printk(KERN_ERR "Invalid chain id\n"); return -EINVAL; } @@ -1294,20 +1456,24 @@ int omap_dma_chain_a_transfer(int chain_id, int src_start, int dest_start, /* Set the params to the free channel */ if (src_start != 0) - OMAP2_DMA_CSSA_REG(lch) = src_start; + dma_write(src_start, CSSA(lch)); if (dest_start != 0) - OMAP2_DMA_CDSA_REG(lch) = dest_start; + dma_write(dest_start, CDSA(lch)); /* Write the buffer size */ - OMAP_DMA_CEN_REG(lch) = elem_count; - OMAP_DMA_CFN_REG(lch) = frame_count; + dma_write(elem_count, CEN(lch)); + dma_write(frame_count, CFN(lch)); - /* If the chain is dynamically linked, - * then we may have to start the chain if its not active */ + /* + * If the chain is dynamically linked, + * then we may have to start the chain if its not active + */ if (dma_linked_lch[chain_id].chain_mode == OMAP_DMA_DYNAMIC_CHAIN) { - /* In Dynamic chain, if the chain is not started, - * queue the channel */ + /* + * In Dynamic chain, if the chain is not started, + * queue the channel + */ if (dma_linked_lch[chain_id].chain_state == DMA_CHAIN_NOTSTARTED) { /* Enable the link in previous channel */ @@ -1317,8 +1483,10 @@ int omap_dma_chain_a_transfer(int chain_id, int src_start, int dest_start, dma_chan[lch].state = DMA_CH_QUEUED; } - /* Chain is already started, make sure its active, - * if not then start the chain */ + /* + * Chain is already started, make sure its active, + * if not then start the chain + */ else { start_dma = 1; @@ -1327,8 +1495,8 @@ int omap_dma_chain_a_transfer(int chain_id, int src_start, int dest_start, enable_lnk(dma_chan[lch].prev_linked_ch); dma_chan[lch].state = DMA_CH_QUEUED; start_dma = 0; - if (0 == ((1 << 7) & (OMAP_DMA_CCR_REG - (dma_chan[lch].prev_linked_ch)))) { + if (0 == ((1 << 7) & dma_read( + CCR(dma_chan[lch].prev_linked_ch)))) { disable_lnk(dma_chan[lch]. prev_linked_ch); pr_debug("\n prev ch is stopped\n"); @@ -1344,27 +1512,28 @@ int omap_dma_chain_a_transfer(int chain_id, int src_start, int dest_start, } omap_enable_channel_irq(lch); - w = OMAP_DMA_CCR_REG(lch); + l = dma_read(CCR(lch)); - if ((0 == (w & (1 << 24)))) - w &= ~(1 << 25); + if ((0 == (l & (1 << 24)))) + l &= ~(1 << 25); else - w |= (1 << 25); + l |= (1 << 25); if (start_dma == 1) { - if (0 == (w & (1 << 7))) { - w |= (1 << 7); + if (0 == (l & (1 << 7))) { + l |= (1 << 7); dma_chan[lch].state = DMA_CH_STARTED; pr_debug("starting %d\n", lch); - OMAP_DMA_CCR_REG(lch) = w; + dma_write(l, CCR(lch)); } else start_dma = 0; } else { - if (0 == (w & (1 << 7))) - OMAP_DMA_CCR_REG(lch) = w; + if (0 == (l & (1 << 7))) + dma_write(l, CCR(lch)); } dma_chan[lch].flags |= OMAP_DMA_ACTIVE; } } + return 0; } EXPORT_SYMBOL(omap_dma_chain_a_transfer); @@ -1380,9 +1549,9 @@ EXPORT_SYMBOL(omap_dma_chain_a_transfer); int omap_start_dma_chain_transfers(int chain_id) { int *channels; - u32 w, i; + u32 l, i; - if (unlikely((chain_id < 0 || chain_id >= OMAP_LOGICAL_DMA_CH_COUNT))) { + if (unlikely((chain_id < 0 || chain_id >= dma_lch_count))) { printk(KERN_ERR "Invalid chain id\n"); return -EINVAL; } @@ -1404,18 +1573,19 @@ int omap_start_dma_chain_transfers(int chain_id) omap_enable_channel_irq(channels[0]); } - w = OMAP_DMA_CCR_REG(channels[0]); - w |= (1 << 7); + l = dma_read(CCR(channels[0])); + l |= (1 << 7); dma_linked_lch[chain_id].chain_state = DMA_CHAIN_STARTED; dma_chan[channels[0]].state = DMA_CH_STARTED; - if ((0 == (w & (1 << 24)))) - w &= ~(1 << 25); + if ((0 == (l & (1 << 24)))) + l &= ~(1 << 25); else - w |= (1 << 25); - OMAP_DMA_CCR_REG(channels[0]) = w; + l |= (1 << 25); + dma_write(l, CCR(channels[0])); dma_chan[channels[0]].flags |= OMAP_DMA_ACTIVE; + return 0; } EXPORT_SYMBOL(omap_start_dma_chain_transfers); @@ -1431,11 +1601,11 @@ EXPORT_SYMBOL(omap_start_dma_chain_transfers); int omap_stop_dma_chain_transfers(int chain_id) { int *channels; - u32 w, i; + u32 l, i; u32 sys_cf; /* Check for input params */ - if (unlikely((chain_id < 0 || chain_id >= OMAP_LOGICAL_DMA_CH_COUNT))) { + if (unlikely((chain_id < 0 || chain_id >= dma_lch_count))) { printk(KERN_ERR "Invalid chain id\n"); return -EINVAL; } @@ -1447,21 +1617,22 @@ int omap_stop_dma_chain_transfers(int chain_id) } channels = dma_linked_lch[chain_id].linked_dmach_q; - /* DMA Errata: + /* + * DMA Errata: * Special programming model needed to disable DMA before end of block */ - sys_cf = omap_readl(OMAP_DMA4_OCP_SYSCONFIG); - w = sys_cf; + sys_cf = dma_read(OCP_SYSCONFIG); + l = sys_cf; /* Middle mode reg set no Standby */ - w &= ~((1 << 12)|(1 << 13)); - omap_writel(w, OMAP_DMA4_OCP_SYSCONFIG); + l &= ~((1 << 12)|(1 << 13)); + dma_write(l, OCP_SYSCONFIG); for (i = 0; i < dma_linked_lch[chain_id].no_of_lchs_linked; i++) { /* Stop the Channel transmission */ - w = OMAP_DMA_CCR_REG(channels[i]); - w &= ~(1 << 7); - OMAP_DMA_CCR_REG(channels[i]) = w; + l = dma_read(CCR(channels[i])); + l &= ~(1 << 7); + dma_write(l, CCR(channels[i])); /* Disable the link in all the channels */ disable_lnk(channels[i]); @@ -1474,7 +1645,8 @@ int omap_stop_dma_chain_transfers(int chain_id) OMAP_DMA_CHAIN_QINIT(chain_id); /* Errata - put in the old value */ - omap_writel(sys_cf, OMAP_DMA4_OCP_SYSCONFIG); + dma_write(sys_cf, OCP_SYSCONFIG); + return 0; } EXPORT_SYMBOL(omap_stop_dma_chain_transfers); @@ -1497,7 +1669,7 @@ int omap_get_dma_chain_index(int chain_id, int *ei, int *fi) int *channels; /* Check for input params */ - if (unlikely((chain_id < 0 || chain_id >= OMAP_LOGICAL_DMA_CH_COUNT))) { + if (unlikely((chain_id < 0 || chain_id >= dma_lch_count))) { printk(KERN_ERR "Invalid chain id\n"); return -EINVAL; } @@ -1515,8 +1687,8 @@ int omap_get_dma_chain_index(int chain_id, int *ei, int *fi) /* Get the current channel */ lch = channels[dma_linked_lch[chain_id].q_head]; - *ei = OMAP2_DMA_CCEN_REG(lch); - *fi = OMAP2_DMA_CCFN_REG(lch); + *ei = dma_read(CCEN(lch)); + *fi = dma_read(CCFN(lch)); return 0; } @@ -1537,7 +1709,7 @@ int omap_get_dma_chain_dst_pos(int chain_id) int *channels; /* Check for input params */ - if (unlikely((chain_id < 0 || chain_id >= OMAP_LOGICAL_DMA_CH_COUNT))) { + if (unlikely((chain_id < 0 || chain_id >= dma_lch_count))) { printk(KERN_ERR "Invalid chain id\n"); return -EINVAL; } @@ -1553,7 +1725,7 @@ int omap_get_dma_chain_dst_pos(int chain_id) /* Get the current channel */ lch = channels[dma_linked_lch[chain_id].q_head]; - return (OMAP_DMA_CDAC_REG(lch)); + return dma_read(CDAC(lch)); } EXPORT_SYMBOL(omap_get_dma_chain_dst_pos); @@ -1571,7 +1743,7 @@ int omap_get_dma_chain_src_pos(int chain_id) int *channels; /* Check for input params */ - if (unlikely((chain_id < 0 || chain_id >= OMAP_LOGICAL_DMA_CH_COUNT))) { + if (unlikely((chain_id < 0 || chain_id >= dma_lch_count))) { printk(KERN_ERR "Invalid chain id\n"); return -EINVAL; } @@ -1587,10 +1759,10 @@ int omap_get_dma_chain_src_pos(int chain_id) /* Get the current channel */ lch = channels[dma_linked_lch[chain_id].q_head]; - return (OMAP_DMA_CSAC_REG(lch)); + return dma_read(CSAC(lch)); } EXPORT_SYMBOL(omap_get_dma_chain_src_pos); -#endif +#endif /* ifndef CONFIG_ARCH_OMAP1 */ /*----------------------------------------------------------------------------*/ @@ -1598,13 +1770,13 @@ EXPORT_SYMBOL(omap_get_dma_chain_src_pos); static int omap1_dma_handle_ch(int ch) { - u16 csr; + u32 csr; if (enable_1510_mode && ch >= 6) { csr = dma_chan[ch].saved_csr; dma_chan[ch].saved_csr = 0; } else - csr = OMAP_DMA_CSR_REG(ch); + csr = dma_read(CSR(ch)); if (enable_1510_mode && ch <= 2 && (csr >> 7) != 0) { dma_chan[ch + 6].saved_csr = csr >> 7; csr &= 0x7f; @@ -1626,6 +1798,7 @@ static int omap1_dma_handle_ch(int ch) dma_chan[ch].flags &= ~OMAP_DMA_ACTIVE; if (likely(dma_chan[ch].callback != NULL)) dma_chan[ch].callback(ch, csr, dma_chan[ch].data); + return 1; } @@ -1656,12 +1829,13 @@ static irqreturn_t omap1_dma_irq_handler(int irq, void *dev_id) static int omap2_dma_handle_ch(int ch) { - u32 status = OMAP_DMA_CSR_REG(ch); + u32 status = dma_read(CSR(ch)); if (!status) { if (printk_ratelimit()) - printk(KERN_WARNING "Spurious DMA IRQ for lch %d\n", ch); - omap_writel(1 << ch, OMAP_DMA4_IRQSTATUS_L0); + printk(KERN_WARNING "Spurious DMA IRQ for lch %d\n", + ch); + dma_write(1 << ch, IRQSTATUS_L0); return 0; } if (unlikely(dma_chan[ch].dev_id == -1)) { @@ -1684,14 +1858,14 @@ static int omap2_dma_handle_ch(int ch) printk(KERN_INFO "DMA misaligned error with device %d\n", dma_chan[ch].dev_id); - OMAP_DMA_CSR_REG(ch) = OMAP2_DMA_CSR_CLEAR_MASK; - omap_writel(1 << ch, OMAP_DMA4_IRQSTATUS_L0); + dma_write(OMAP2_DMA_CSR_CLEAR_MASK, CSR(ch)); + dma_write(1 << ch, IRQSTATUS_L0); /* If the ch is not chained then chain_id will be -1 */ if (dma_chan[ch].chain_id != -1) { int chain_id = dma_chan[ch].chain_id; dma_chan[ch].state = DMA_CH_NOTSTARTED; - if (OMAP_DMA_CLNK_CTRL_REG(ch) & (1 << 15)) + if (dma_read(CLNK_CTRL(ch)) & (1 << 15)) dma_chan[dma_chan[ch].next_linked_ch].state = DMA_CH_STARTED; if (dma_linked_lch[chain_id].chain_mode == @@ -1701,13 +1875,13 @@ static int omap2_dma_handle_ch(int ch) if (!OMAP_DMA_CHAIN_QEMPTY(chain_id)) OMAP_DMA_CHAIN_INCQHEAD(chain_id); - status = OMAP_DMA_CSR_REG(ch); + status = dma_read(CSR(ch)); } if (likely(dma_chan[ch].callback != NULL)) dma_chan[ch].callback(ch, status, dma_chan[ch].data); - OMAP_DMA_CSR_REG(ch) = status; + dma_write(status, CSR(ch)); return 0; } @@ -1718,13 +1892,13 @@ static irqreturn_t omap2_dma_irq_handler(int irq, void *dev_id) u32 val; int i; - val = omap_readl(OMAP_DMA4_IRQSTATUS_L0); + val = dma_read(IRQSTATUS_L0); if (val == 0) { if (printk_ratelimit()) printk(KERN_WARNING "Spurious DMA IRQ\n"); return IRQ_HANDLED; } - for (i = 0; i < OMAP_LOGICAL_DMA_CH_COUNT && val != 0; i++) { + for (i = 0; i < dma_lch_count && val != 0; i++) { if (val & 1) omap2_dma_handle_ch(i); val >>= 1; @@ -1748,7 +1922,7 @@ static struct irqaction omap24xx_dma_irq; static struct lcd_dma_info { spinlock_t lock; int reserved; - void (* callback)(u16 status, void *data); + void (*callback)(u16 status, void *data); void *cb_data; int active; @@ -1770,6 +1944,7 @@ void omap_set_lcd_dma_b1(unsigned long addr, u16 fb_xres, u16 fb_yres, lcd_dma.xres = fb_xres; lcd_dma.yres = fb_yres; } +EXPORT_SYMBOL(omap_set_lcd_dma_b1); void omap_set_lcd_dma_src_port(int port) { @@ -1780,12 +1955,13 @@ void omap_set_lcd_dma_ext_controller(int external) { lcd_dma.ext_ctrl = external; } +EXPORT_SYMBOL(omap_set_lcd_dma_ext_controller); void omap_set_lcd_dma_single_transfer(int single) { lcd_dma.single_transfer = single; } - +EXPORT_SYMBOL(omap_set_lcd_dma_single_transfer); void omap_set_lcd_dma_b1_rotation(int rotate) { @@ -1796,6 +1972,7 @@ void omap_set_lcd_dma_b1_rotation(int rotate) } lcd_dma.rotate = rotate; } +EXPORT_SYMBOL(omap_set_lcd_dma_b1_rotation); void omap_set_lcd_dma_b1_mirror(int mirror) { @@ -1805,6 +1982,7 @@ void omap_set_lcd_dma_b1_mirror(int mirror) } lcd_dma.mirror = mirror; } +EXPORT_SYMBOL(omap_set_lcd_dma_b1_mirror); void omap_set_lcd_dma_b1_vxres(unsigned long vxres) { @@ -1815,6 +1993,7 @@ void omap_set_lcd_dma_b1_vxres(unsigned long vxres) } lcd_dma.vxres = vxres; } +EXPORT_SYMBOL(omap_set_lcd_dma_b1_vxres); void omap_set_lcd_dma_b1_scale(unsigned int xscale, unsigned int yscale) { @@ -1825,6 +2004,7 @@ void omap_set_lcd_dma_b1_scale(unsigned int xscale, unsigned int yscale) lcd_dma.xscale = xscale; lcd_dma.yscale = yscale; } +EXPORT_SYMBOL(omap_set_lcd_dma_b1_scale); static void set_b1_regs(void) { @@ -1855,8 +2035,11 @@ static void set_b1_regs(void) xscale = lcd_dma.xscale ? lcd_dma.xscale : 1; yscale = lcd_dma.yscale ? lcd_dma.yscale : 1; BUG_ON(vxres < lcd_dma.xres); -#define PIXADDR(x,y) (lcd_dma.addr + ((y) * vxres * yscale + (x) * xscale) * es) + +#define PIXADDR(x, y) (lcd_dma.addr + \ + ((y) * vxres * yscale + (x) * xscale) * es) #define PIXSTEP(sx, sy, dx, dy) (PIXADDR(dx, dy) - PIXADDR(sx, sy) - es + 1) + switch (lcd_dma.rotate) { case 0: if (!lcd_dma.mirror) { @@ -1865,8 +2048,8 @@ static void set_b1_regs(void) /* 1510 DMA requires the bottom address to be 2 more * than the actual last memory access location. */ if (omap_dma_in_1510_mode() && - lcd_dma.data_type == OMAP_DMA_DATA_TYPE_S32) - bottom += 2; + lcd_dma.data_type == OMAP_DMA_DATA_TYPE_S32) + bottom += 2; ei = PIXSTEP(0, 0, 1, 0); fi = PIXSTEP(lcd_dma.xres - 1, 0, 0, 1); } else { @@ -1993,7 +2176,7 @@ static irqreturn_t lcd_dma_irq_handler(int irq, void *dev_id) return IRQ_HANDLED; } -int omap_request_lcd_dma(void (* callback)(u16 status, void *data), +int omap_request_lcd_dma(void (*callback)(u16 status, void *data), void *data) { spin_lock_irq(&lcd_dma.lock); @@ -2019,6 +2202,7 @@ int omap_request_lcd_dma(void (* callback)(u16 status, void *data), return 0; } +EXPORT_SYMBOL(omap_request_lcd_dma); void omap_free_lcd_dma(void) { @@ -2035,12 +2219,14 @@ void omap_free_lcd_dma(void) lcd_dma.reserved = 0; spin_unlock(&lcd_dma.lock); } +EXPORT_SYMBOL(omap_free_lcd_dma); void omap_enable_lcd_dma(void) { u16 w; - /* Set the Enable bit only if an external controller is + /* + * Set the Enable bit only if an external controller is * connected. Otherwise the OMAP internal controller will * start the transfer when it gets enabled. */ @@ -2057,6 +2243,7 @@ void omap_enable_lcd_dma(void) w |= 1 << 7; omap_writew(w, OMAP1610_DMA_LCD_CCR); } +EXPORT_SYMBOL(omap_enable_lcd_dma); void omap_setup_lcd_dma(void) { @@ -2072,16 +2259,18 @@ void omap_setup_lcd_dma(void) u16 w; w = omap_readw(OMAP1610_DMA_LCD_CCR); - /* If DMA was already active set the end_prog bit to have + /* + * If DMA was already active set the end_prog bit to have * the programmed register set loaded into the active * register set. */ w |= 1 << 11; /* End_prog */ if (!lcd_dma.single_transfer) - w |= (3 << 8); /* Auto_init, repeat */ + w |= (3 << 8); /* Auto_init, repeat */ omap_writew(w, OMAP1610_DMA_LCD_CCR); } } +EXPORT_SYMBOL(omap_setup_lcd_dma); void omap_stop_lcd_dma(void) { @@ -2099,6 +2288,7 @@ void omap_stop_lcd_dma(void) w &= ~(1 << 8); omap_writew(w, OMAP1610_DMA_LCD_CTRL); } +EXPORT_SYMBOL(omap_stop_lcd_dma); /*----------------------------------------------------------------------------*/ @@ -2106,27 +2296,55 @@ static int __init omap_init_dma(void) { int ch, r; + if (cpu_class_is_omap1()) { + omap_dma_base = (void __iomem *)IO_ADDRESS(OMAP1_DMA_BASE); + dma_lch_count = OMAP1_LOGICAL_DMA_CH_COUNT; + } else if (cpu_is_omap24xx()) { + omap_dma_base = (void __iomem *)IO_ADDRESS(OMAP24XX_DMA4_BASE); + dma_lch_count = OMAP_DMA4_LOGICAL_DMA_CH_COUNT; + } else if (cpu_is_omap34xx()) { + omap_dma_base = (void __iomem *)IO_ADDRESS(OMAP34XX_DMA4_BASE); + dma_lch_count = OMAP_DMA4_LOGICAL_DMA_CH_COUNT; + } else { + pr_err("DMA init failed for unsupported omap\n"); + return -ENODEV; + } + + dma_chan = kzalloc(sizeof(struct omap_dma_lch) * dma_lch_count, + GFP_KERNEL); + if (!dma_chan) + return -ENOMEM; + + if (cpu_class_is_omap2()) { + dma_linked_lch = kzalloc(sizeof(struct dma_link_info) * + dma_lch_count, GFP_KERNEL); + if (!dma_linked_lch) { + kfree(dma_chan); + return -ENOMEM; + } + } + if (cpu_is_omap15xx()) { printk(KERN_INFO "DMA support for OMAP15xx initialized\n"); dma_chan_count = 9; enable_1510_mode = 1; } else if (cpu_is_omap16xx() || cpu_is_omap730()) { printk(KERN_INFO "OMAP DMA hardware version %d\n", - omap_readw(OMAP_DMA_HW_ID)); + dma_read(HW_ID)); printk(KERN_INFO "DMA capabilities: %08x:%08x:%04x:%04x:%04x\n", - (omap_readw(OMAP_DMA_CAPS_0_U) << 16) | - omap_readw(OMAP_DMA_CAPS_0_L), - (omap_readw(OMAP_DMA_CAPS_1_U) << 16) | - omap_readw(OMAP_DMA_CAPS_1_L), - omap_readw(OMAP_DMA_CAPS_2), omap_readw(OMAP_DMA_CAPS_3), - omap_readw(OMAP_DMA_CAPS_4)); + (dma_read(CAPS_0_U) << 16) | + dma_read(CAPS_0_L), + (dma_read(CAPS_1_U) << 16) | + dma_read(CAPS_1_L), + dma_read(CAPS_2), dma_read(CAPS_3), + dma_read(CAPS_4)); if (!enable_1510_mode) { u16 w; /* Disable OMAP 3.0/3.1 compatibility mode. */ - w = omap_readw(OMAP_DMA_GSCR); + w = dma_read(GSCR); w |= 1 << 3; - omap_writew(w, OMAP_DMA_GSCR); + dma_write(w, GSCR); dma_chan_count = 16; } else dma_chan_count = 9; @@ -2139,19 +2357,17 @@ static int __init omap_init_dma(void) omap_writew(w, OMAP1610_DMA_LCD_CTRL); } } else if (cpu_class_is_omap2()) { - u8 revision = omap_readb(OMAP_DMA4_REVISION); + u8 revision = dma_read(REVISION) & 0xff; printk(KERN_INFO "OMAP DMA hardware revision %d.%d\n", revision >> 4, revision & 0xf); - dma_chan_count = OMAP_LOGICAL_DMA_CH_COUNT; + dma_chan_count = OMAP_DMA4_LOGICAL_DMA_CH_COUNT; } else { dma_chan_count = 0; return 0; } - memset(&lcd_dma, 0, sizeof(lcd_dma)); spin_lock_init(&lcd_dma.lock); spin_lock_init(&dma_chan_lock); - memset(&dma_chan, 0, sizeof(dma_chan)); for (ch = 0; ch < dma_chan_count; ch++) { omap_clear_dma(ch); @@ -2162,8 +2378,10 @@ static int __init omap_init_dma(void) continue; if (cpu_class_is_omap1()) { - /* request_irq() doesn't like dev_id (ie. ch) being - * zero, so we have to kludge around this. */ + /* + * request_irq() doesn't like dev_id (ie. ch) being + * zero, so we have to kludge around this. + */ r = request_irq(omap1_dma_irq[ch], omap1_dma_irq_handler, 0, "DMA", (void *) (ch + 1)); @@ -2208,48 +2426,4 @@ static int __init omap_init_dma(void) arch_initcall(omap_init_dma); -EXPORT_SYMBOL(omap_get_dma_src_pos); -EXPORT_SYMBOL(omap_get_dma_dst_pos); -EXPORT_SYMBOL(omap_get_dma_src_addr_counter); -EXPORT_SYMBOL(omap_clear_dma); -EXPORT_SYMBOL(omap_set_dma_priority); -EXPORT_SYMBOL(omap_request_dma); -EXPORT_SYMBOL(omap_free_dma); -EXPORT_SYMBOL(omap_start_dma); -EXPORT_SYMBOL(omap_stop_dma); -EXPORT_SYMBOL(omap_set_dma_callback); -EXPORT_SYMBOL(omap_enable_dma_irq); -EXPORT_SYMBOL(omap_disable_dma_irq); - -EXPORT_SYMBOL(omap_set_dma_transfer_params); -EXPORT_SYMBOL(omap_set_dma_color_mode); -EXPORT_SYMBOL(omap_set_dma_write_mode); - -EXPORT_SYMBOL(omap_set_dma_src_params); -EXPORT_SYMBOL(omap_set_dma_src_index); -EXPORT_SYMBOL(omap_set_dma_src_data_pack); -EXPORT_SYMBOL(omap_set_dma_src_burst_mode); - -EXPORT_SYMBOL(omap_set_dma_dest_params); -EXPORT_SYMBOL(omap_set_dma_dest_index); -EXPORT_SYMBOL(omap_set_dma_dest_data_pack); -EXPORT_SYMBOL(omap_set_dma_dest_burst_mode); - -EXPORT_SYMBOL(omap_set_dma_params); - -EXPORT_SYMBOL(omap_dma_link_lch); -EXPORT_SYMBOL(omap_dma_unlink_lch); - -EXPORT_SYMBOL(omap_request_lcd_dma); -EXPORT_SYMBOL(omap_free_lcd_dma); -EXPORT_SYMBOL(omap_enable_lcd_dma); -EXPORT_SYMBOL(omap_setup_lcd_dma); -EXPORT_SYMBOL(omap_stop_lcd_dma); -EXPORT_SYMBOL(omap_set_lcd_dma_b1); -EXPORT_SYMBOL(omap_set_lcd_dma_single_transfer); -EXPORT_SYMBOL(omap_set_lcd_dma_ext_controller); -EXPORT_SYMBOL(omap_set_lcd_dma_b1_rotation); -EXPORT_SYMBOL(omap_set_lcd_dma_b1_vxres); -EXPORT_SYMBOL(omap_set_lcd_dma_b1_scale); -EXPORT_SYMBOL(omap_set_lcd_dma_b1_mirror); diff --git a/arch/arm/plat-omap/dmtimer.c b/arch/arm/plat-omap/dmtimer.c index 302ad8dff2c..f22506af0e6 100644 --- a/arch/arm/plat-omap/dmtimer.c +++ b/arch/arm/plat-omap/dmtimer.c @@ -38,34 +38,113 @@ #include <asm/arch/irqs.h> /* register offsets */ -#define OMAP_TIMER_ID_REG 0x00 -#define OMAP_TIMER_OCP_CFG_REG 0x10 -#define OMAP_TIMER_SYS_STAT_REG 0x14 -#define OMAP_TIMER_STAT_REG 0x18 -#define OMAP_TIMER_INT_EN_REG 0x1c -#define OMAP_TIMER_WAKEUP_EN_REG 0x20 -#define OMAP_TIMER_CTRL_REG 0x24 -#define OMAP_TIMER_COUNTER_REG 0x28 -#define OMAP_TIMER_LOAD_REG 0x2c -#define OMAP_TIMER_TRIGGER_REG 0x30 -#define OMAP_TIMER_WRITE_PEND_REG 0x34 -#define OMAP_TIMER_MATCH_REG 0x38 -#define OMAP_TIMER_CAPTURE_REG 0x3c -#define OMAP_TIMER_IF_CTRL_REG 0x40 - -/* timer control reg bits */ -#define OMAP_TIMER_CTRL_GPOCFG (1 << 14) -#define OMAP_TIMER_CTRL_CAPTMODE (1 << 13) -#define OMAP_TIMER_CTRL_PT (1 << 12) -#define OMAP_TIMER_CTRL_TCM_LOWTOHIGH (0x1 << 8) -#define OMAP_TIMER_CTRL_TCM_HIGHTOLOW (0x2 << 8) -#define OMAP_TIMER_CTRL_TCM_BOTHEDGES (0x3 << 8) -#define OMAP_TIMER_CTRL_SCPWM (1 << 7) -#define OMAP_TIMER_CTRL_CE (1 << 6) /* compare enable */ -#define OMAP_TIMER_CTRL_PRE (1 << 5) /* prescaler enable */ -#define OMAP_TIMER_CTRL_PTV_SHIFT 2 /* how much to shift the prescaler value */ -#define OMAP_TIMER_CTRL_AR (1 << 1) /* auto-reload enable */ -#define OMAP_TIMER_CTRL_ST (1 << 0) /* start timer */ +#define _OMAP_TIMER_ID_OFFSET 0x00 +#define _OMAP_TIMER_OCP_CFG_OFFSET 0x10 +#define _OMAP_TIMER_SYS_STAT_OFFSET 0x14 +#define _OMAP_TIMER_STAT_OFFSET 0x18 +#define _OMAP_TIMER_INT_EN_OFFSET 0x1c +#define _OMAP_TIMER_WAKEUP_EN_OFFSET 0x20 +#define _OMAP_TIMER_CTRL_OFFSET 0x24 +#define OMAP_TIMER_CTRL_GPOCFG (1 << 14) +#define OMAP_TIMER_CTRL_CAPTMODE (1 << 13) +#define OMAP_TIMER_CTRL_PT (1 << 12) +#define OMAP_TIMER_CTRL_TCM_LOWTOHIGH (0x1 << 8) +#define OMAP_TIMER_CTRL_TCM_HIGHTOLOW (0x2 << 8) +#define OMAP_TIMER_CTRL_TCM_BOTHEDGES (0x3 << 8) +#define OMAP_TIMER_CTRL_SCPWM (1 << 7) +#define OMAP_TIMER_CTRL_CE (1 << 6) /* compare enable */ +#define OMAP_TIMER_CTRL_PRE (1 << 5) /* prescaler enable */ +#define OMAP_TIMER_CTRL_PTV_SHIFT 2 /* prescaler value shift */ +#define OMAP_TIMER_CTRL_POSTED (1 << 2) +#define OMAP_TIMER_CTRL_AR (1 << 1) /* auto-reload enable */ +#define OMAP_TIMER_CTRL_ST (1 << 0) /* start timer */ +#define _OMAP_TIMER_COUNTER_OFFSET 0x28 +#define _OMAP_TIMER_LOAD_OFFSET 0x2c +#define _OMAP_TIMER_TRIGGER_OFFSET 0x30 +#define _OMAP_TIMER_WRITE_PEND_OFFSET 0x34 +#define WP_NONE 0 /* no write pending bit */ +#define WP_TCLR (1 << 0) +#define WP_TCRR (1 << 1) +#define WP_TLDR (1 << 2) +#define WP_TTGR (1 << 3) +#define WP_TMAR (1 << 4) +#define WP_TPIR (1 << 5) +#define WP_TNIR (1 << 6) +#define WP_TCVR (1 << 7) +#define WP_TOCR (1 << 8) +#define WP_TOWR (1 << 9) +#define _OMAP_TIMER_MATCH_OFFSET 0x38 +#define _OMAP_TIMER_CAPTURE_OFFSET 0x3c +#define _OMAP_TIMER_IF_CTRL_OFFSET 0x40 +#define _OMAP_TIMER_CAPTURE2_OFFSET 0x44 /* TCAR2, 34xx only */ +#define _OMAP_TIMER_TICK_POS_OFFSET 0x48 /* TPIR, 34xx only */ +#define _OMAP_TIMER_TICK_NEG_OFFSET 0x4c /* TNIR, 34xx only */ +#define _OMAP_TIMER_TICK_COUNT_OFFSET 0x50 /* TCVR, 34xx only */ +#define _OMAP_TIMER_TICK_INT_MASK_SET_OFFSET 0x54 /* TOCR, 34xx only */ +#define _OMAP_TIMER_TICK_INT_MASK_COUNT_OFFSET 0x58 /* TOWR, 34xx only */ + +/* register offsets with the write pending bit encoded */ +#define WPSHIFT 16 + +#define OMAP_TIMER_ID_REG (_OMAP_TIMER_ID_OFFSET \ + | (WP_NONE << WPSHIFT)) + +#define OMAP_TIMER_OCP_CFG_REG (_OMAP_TIMER_OCP_CFG_OFFSET \ + | (WP_NONE << WPSHIFT)) + +#define OMAP_TIMER_SYS_STAT_REG (_OMAP_TIMER_SYS_STAT_OFFSET \ + | (WP_NONE << WPSHIFT)) + +#define OMAP_TIMER_STAT_REG (_OMAP_TIMER_STAT_OFFSET \ + | (WP_NONE << WPSHIFT)) + +#define OMAP_TIMER_INT_EN_REG (_OMAP_TIMER_INT_EN_OFFSET \ + | (WP_NONE << WPSHIFT)) + +#define OMAP_TIMER_WAKEUP_EN_REG (_OMAP_TIMER_WAKEUP_EN_OFFSET \ + | (WP_NONE << WPSHIFT)) + +#define OMAP_TIMER_CTRL_REG (_OMAP_TIMER_CTRL_OFFSET \ + | (WP_TCLR << WPSHIFT)) + +#define OMAP_TIMER_COUNTER_REG (_OMAP_TIMER_COUNTER_OFFSET \ + | (WP_TCRR << WPSHIFT)) + +#define OMAP_TIMER_LOAD_REG (_OMAP_TIMER_LOAD_OFFSET \ + | (WP_TLDR << WPSHIFT)) + +#define OMAP_TIMER_TRIGGER_REG (_OMAP_TIMER_TRIGGER_OFFSET \ + | (WP_TTGR << WPSHIFT)) + +#define OMAP_TIMER_WRITE_PEND_REG (_OMAP_TIMER_WRITE_PEND_OFFSET \ + | (WP_NONE << WPSHIFT)) + +#define OMAP_TIMER_MATCH_REG (_OMAP_TIMER_MATCH_OFFSET \ + | (WP_TMAR << WPSHIFT)) + +#define OMAP_TIMER_CAPTURE_REG (_OMAP_TIMER_CAPTURE_OFFSET \ + | (WP_NONE << WPSHIFT)) + +#define OMAP_TIMER_IF_CTRL_REG (_OMAP_TIMER_IF_CTRL_OFFSET \ + | (WP_NONE << WPSHIFT)) + +#define OMAP_TIMER_CAPTURE2_REG (_OMAP_TIMER_CAPTURE2_OFFSET \ + | (WP_NONE << WPSHIFT)) + +#define OMAP_TIMER_TICK_POS_REG (_OMAP_TIMER_TICK_POS_OFFSET \ + | (WP_TPIR << WPSHIFT)) + +#define OMAP_TIMER_TICK_NEG_REG (_OMAP_TIMER_TICK_NEG_OFFSET \ + | (WP_TNIR << WPSHIFT)) + +#define OMAP_TIMER_TICK_COUNT_REG (_OMAP_TIMER_TICK_COUNT_OFFSET \ + | (WP_TCVR << WPSHIFT)) + +#define OMAP_TIMER_TICK_INT_MASK_SET_REG \ + (_OMAP_TIMER_TICK_INT_MASK_SET_OFFSET | (WP_TOCR << WPSHIFT)) + +#define OMAP_TIMER_TICK_INT_MASK_COUNT_REG \ + (_OMAP_TIMER_TICK_INT_MASK_COUNT_OFFSET | (WP_TOWR << WPSHIFT)) struct omap_dm_timer { unsigned long phys_base; @@ -76,6 +155,7 @@ struct omap_dm_timer { void __iomem *io_base; unsigned reserved:1; unsigned enabled:1; + unsigned posted:1; }; #ifdef CONFIG_ARCH_OMAP1 @@ -181,16 +261,34 @@ static struct clk **dm_source_clocks; static spinlock_t dm_timer_lock; -static inline u32 omap_dm_timer_read_reg(struct omap_dm_timer *timer, int reg) +/* + * Reads timer registers in posted and non-posted mode. The posted mode bit + * is encoded in reg. Note that in posted mode write pending bit must be + * checked. Otherwise a read of a non completed write will produce an error. + */ +static inline u32 omap_dm_timer_read_reg(struct omap_dm_timer *timer, u32 reg) { - return readl(timer->io_base + reg); + if (timer->posted) + while (readl(timer->io_base + (OMAP_TIMER_WRITE_PEND_REG & 0xff)) + & (reg >> WPSHIFT)) + cpu_relax(); + return readl(timer->io_base + (reg & 0xff)); } -static void omap_dm_timer_write_reg(struct omap_dm_timer *timer, int reg, u32 value) +/* + * Writes timer registers in posted and non-posted mode. The posted mode bit + * is encoded in reg. Note that in posted mode the write pending bit must be + * checked. Otherwise a write on a register which has a pending write will be + * lost. + */ +static void omap_dm_timer_write_reg(struct omap_dm_timer *timer, u32 reg, + u32 value) { - writel(value, timer->io_base + reg); - while (omap_dm_timer_read_reg(timer, OMAP_TIMER_WRITE_PEND_REG)) - ; + if (timer->posted) + while (readl(timer->io_base + (OMAP_TIMER_WRITE_PEND_REG & 0xff)) + & (reg >> WPSHIFT)) + cpu_relax(); + writel(value, timer->io_base + (reg & 0xff)); } static void omap_dm_timer_wait_for_reset(struct omap_dm_timer *timer) @@ -217,17 +315,23 @@ static void omap_dm_timer_reset(struct omap_dm_timer *timer) } omap_dm_timer_set_source(timer, OMAP_TIMER_SRC_32_KHZ); - /* Set to smart-idle mode */ l = omap_dm_timer_read_reg(timer, OMAP_TIMER_OCP_CFG_REG); - l |= 0x02 << 3; - - if (cpu_class_is_omap2() && timer == &dm_timers[0]) { - /* Enable wake-up only for GPT1 on OMAP2 CPUs*/ + l |= 0x02 << 3; /* Set to smart-idle mode */ + l |= 0x2 << 8; /* Set clock activity to perserve f-clock on idle */ + + /* + * Enable wake-up only for GPT1 on OMAP2 CPUs. + * FIXME: All timers should have wake-up enabled and clear + * PRCM status. + */ + if (cpu_class_is_omap2() && (timer == &dm_timers[0])) l |= 1 << 2; - /* Non-posted mode */ - omap_dm_timer_write_reg(timer, OMAP_TIMER_IF_CTRL_REG, 0); - } omap_dm_timer_write_reg(timer, OMAP_TIMER_OCP_CFG_REG, l); + + /* Match hardware reset default of posted mode */ + omap_dm_timer_write_reg(timer, OMAP_TIMER_IF_CTRL_REG, + OMAP_TIMER_CTRL_POSTED); + timer->posted = 1; } static void omap_dm_timer_prepare(struct omap_dm_timer *timer) @@ -434,9 +538,32 @@ void omap_dm_timer_set_load(struct omap_dm_timer *timer, int autoreload, l &= ~OMAP_TIMER_CTRL_AR; omap_dm_timer_write_reg(timer, OMAP_TIMER_CTRL_REG, l); omap_dm_timer_write_reg(timer, OMAP_TIMER_LOAD_REG, load); + + /* REVISIT: hw feature, ttgr overtaking tldr? */ + while (readl(timer->io_base + (OMAP_TIMER_WRITE_PEND_REG & 0xff))) + cpu_relax(); + omap_dm_timer_write_reg(timer, OMAP_TIMER_TRIGGER_REG, 0); } +/* Optimized set_load which removes costly spin wait in timer_start */ +void omap_dm_timer_set_load_start(struct omap_dm_timer *timer, int autoreload, + unsigned int load) +{ + u32 l; + + l = omap_dm_timer_read_reg(timer, OMAP_TIMER_CTRL_REG); + if (autoreload) + l |= OMAP_TIMER_CTRL_AR; + else + l &= ~OMAP_TIMER_CTRL_AR; + l |= OMAP_TIMER_CTRL_ST; + + omap_dm_timer_write_reg(timer, OMAP_TIMER_COUNTER_REG, load); + omap_dm_timer_write_reg(timer, OMAP_TIMER_LOAD_REG, load); + omap_dm_timer_write_reg(timer, OMAP_TIMER_CTRL_REG, l); +} + void omap_dm_timer_set_match(struct omap_dm_timer *timer, int enable, unsigned int match) { @@ -451,7 +578,6 @@ void omap_dm_timer_set_match(struct omap_dm_timer *timer, int enable, omap_dm_timer_write_reg(timer, OMAP_TIMER_MATCH_REG, match); } - void omap_dm_timer_set_pwm(struct omap_dm_timer *timer, int def_on, int toggle, int trigger) { diff --git a/arch/arm/plat-omap/mcbsp.c b/arch/arm/plat-omap/mcbsp.c index 9cf83c4da9f..c7f74064696 100644 --- a/arch/arm/plat-omap/mcbsp.c +++ b/arch/arm/plat-omap/mcbsp.c @@ -15,95 +15,66 @@ #include <linux/module.h> #include <linux/init.h> #include <linux/device.h> +#include <linux/platform_device.h> #include <linux/wait.h> #include <linux/completion.h> #include <linux/interrupt.h> #include <linux/err.h> #include <linux/clk.h> #include <linux/delay.h> - -#include <asm/io.h> -#include <asm/irq.h> +#include <linux/io.h> #include <asm/arch/dma.h> -#include <asm/arch/mux.h> -#include <asm/arch/irqs.h> -#include <asm/arch/dsp_common.h> #include <asm/arch/mcbsp.h> -#ifdef CONFIG_MCBSP_DEBUG -#define DBG(x...) printk(x) -#else -#define DBG(x...) do { } while (0) -#endif - -struct omap_mcbsp { - u32 io_base; - u8 id; - u8 free; - omap_mcbsp_word_length rx_word_length; - omap_mcbsp_word_length tx_word_length; - - omap_mcbsp_io_type_t io_type; /* IRQ or poll */ - /* IRQ based TX/RX */ - int rx_irq; - int tx_irq; - - /* DMA stuff */ - u8 dma_rx_sync; - short dma_rx_lch; - u8 dma_tx_sync; - short dma_tx_lch; - - /* Completion queues */ - struct completion tx_irq_completion; - struct completion rx_irq_completion; - struct completion tx_dma_completion; - struct completion rx_dma_completion; - - spinlock_t lock; -}; - static struct omap_mcbsp mcbsp[OMAP_MAX_MCBSP_COUNT]; -#ifdef CONFIG_ARCH_OMAP1 -static struct clk *mcbsp_dsp_ck = 0; -static struct clk *mcbsp_api_ck = 0; -static struct clk *mcbsp_dspxor_ck = 0; -#endif -#ifdef CONFIG_ARCH_OMAP2 -static struct clk *mcbsp1_ick = 0; -static struct clk *mcbsp1_fck = 0; -static struct clk *mcbsp2_ick = 0; -static struct clk *mcbsp2_fck = 0; -#endif + +#define omap_mcbsp_check_valid_id(id) (mcbsp[id].pdata && \ + mcbsp[id].pdata->ops && \ + mcbsp[id].pdata->ops->check && \ + (mcbsp[id].pdata->ops->check(id) == 0)) static void omap_mcbsp_dump_reg(u8 id) { - DBG("**** MCBSP%d regs ****\n", mcbsp[id].id); - DBG("DRR2: 0x%04x\n", OMAP_MCBSP_READ(mcbsp[id].io_base, DRR2)); - DBG("DRR1: 0x%04x\n", OMAP_MCBSP_READ(mcbsp[id].io_base, DRR1)); - DBG("DXR2: 0x%04x\n", OMAP_MCBSP_READ(mcbsp[id].io_base, DXR2)); - DBG("DXR1: 0x%04x\n", OMAP_MCBSP_READ(mcbsp[id].io_base, DXR1)); - DBG("SPCR2: 0x%04x\n", OMAP_MCBSP_READ(mcbsp[id].io_base, SPCR2)); - DBG("SPCR1: 0x%04x\n", OMAP_MCBSP_READ(mcbsp[id].io_base, SPCR1)); - DBG("RCR2: 0x%04x\n", OMAP_MCBSP_READ(mcbsp[id].io_base, RCR2)); - DBG("RCR1: 0x%04x\n", OMAP_MCBSP_READ(mcbsp[id].io_base, RCR1)); - DBG("XCR2: 0x%04x\n", OMAP_MCBSP_READ(mcbsp[id].io_base, XCR2)); - DBG("XCR1: 0x%04x\n", OMAP_MCBSP_READ(mcbsp[id].io_base, XCR1)); - DBG("SRGR2: 0x%04x\n", OMAP_MCBSP_READ(mcbsp[id].io_base, SRGR2)); - DBG("SRGR1: 0x%04x\n", OMAP_MCBSP_READ(mcbsp[id].io_base, SRGR1)); - DBG("PCR0: 0x%04x\n", OMAP_MCBSP_READ(mcbsp[id].io_base, PCR0)); - DBG("***********************\n"); + dev_dbg(mcbsp[id].dev, "**** McBSP%d regs ****\n", mcbsp[id].id); + dev_dbg(mcbsp[id].dev, "DRR2: 0x%04x\n", + OMAP_MCBSP_READ(mcbsp[id].io_base, DRR2)); + dev_dbg(mcbsp[id].dev, "DRR1: 0x%04x\n", + OMAP_MCBSP_READ(mcbsp[id].io_base, DRR1)); + dev_dbg(mcbsp[id].dev, "DXR2: 0x%04x\n", + OMAP_MCBSP_READ(mcbsp[id].io_base, DXR2)); + dev_dbg(mcbsp[id].dev, "DXR1: 0x%04x\n", + OMAP_MCBSP_READ(mcbsp[id].io_base, DXR1)); + dev_dbg(mcbsp[id].dev, "SPCR2: 0x%04x\n", + OMAP_MCBSP_READ(mcbsp[id].io_base, SPCR2)); + dev_dbg(mcbsp[id].dev, "SPCR1: 0x%04x\n", + OMAP_MCBSP_READ(mcbsp[id].io_base, SPCR1)); + dev_dbg(mcbsp[id].dev, "RCR2: 0x%04x\n", + OMAP_MCBSP_READ(mcbsp[id].io_base, RCR2)); + dev_dbg(mcbsp[id].dev, "RCR1: 0x%04x\n", + OMAP_MCBSP_READ(mcbsp[id].io_base, RCR1)); + dev_dbg(mcbsp[id].dev, "XCR2: 0x%04x\n", + OMAP_MCBSP_READ(mcbsp[id].io_base, XCR2)); + dev_dbg(mcbsp[id].dev, "XCR1: 0x%04x\n", + OMAP_MCBSP_READ(mcbsp[id].io_base, XCR1)); + dev_dbg(mcbsp[id].dev, "SRGR2: 0x%04x\n", + OMAP_MCBSP_READ(mcbsp[id].io_base, SRGR2)); + dev_dbg(mcbsp[id].dev, "SRGR1: 0x%04x\n", + OMAP_MCBSP_READ(mcbsp[id].io_base, SRGR1)); + dev_dbg(mcbsp[id].dev, "PCR0: 0x%04x\n", + OMAP_MCBSP_READ(mcbsp[id].io_base, PCR0)); + dev_dbg(mcbsp[id].dev, "***********************\n"); } static irqreturn_t omap_mcbsp_tx_irq_handler(int irq, void *dev_id) { struct omap_mcbsp *mcbsp_tx = dev_id; - DBG("TX IRQ callback : 0x%x\n", - OMAP_MCBSP_READ(mcbsp_tx->io_base, SPCR2)); + dev_dbg(mcbsp_tx->dev, "TX IRQ callback : 0x%x\n", + OMAP_MCBSP_READ(mcbsp_tx->io_base, SPCR2)); complete(&mcbsp_tx->tx_irq_completion); + return IRQ_HANDLED; } @@ -111,10 +82,11 @@ static irqreturn_t omap_mcbsp_rx_irq_handler(int irq, void *dev_id) { struct omap_mcbsp *mcbsp_rx = dev_id; - DBG("RX IRQ callback : 0x%x\n", - OMAP_MCBSP_READ(mcbsp_rx->io_base, SPCR2)); + dev_dbg(mcbsp_rx->dev, "RX IRQ callback : 0x%x\n", + OMAP_MCBSP_READ(mcbsp_rx->io_base, SPCR2)); complete(&mcbsp_rx->rx_irq_completion); + return IRQ_HANDLED; } @@ -122,8 +94,8 @@ static void omap_mcbsp_tx_dma_callback(int lch, u16 ch_status, void *data) { struct omap_mcbsp *mcbsp_dma_tx = data; - DBG("TX DMA callback : 0x%x\n", - OMAP_MCBSP_READ(mcbsp_dma_tx->io_base, SPCR2)); + dev_dbg(mcbsp_dma_tx->dev, "TX DMA callback : 0x%x\n", + OMAP_MCBSP_READ(mcbsp_dma_tx->io_base, SPCR2)); /* We can free the channels */ omap_free_dma(mcbsp_dma_tx->dma_tx_lch); @@ -136,8 +108,8 @@ static void omap_mcbsp_rx_dma_callback(int lch, u16 ch_status, void *data) { struct omap_mcbsp *mcbsp_dma_rx = data; - DBG("RX DMA callback : 0x%x\n", - OMAP_MCBSP_READ(mcbsp_dma_rx->io_base, SPCR2)); + dev_dbg(mcbsp_dma_rx->dev, "RX DMA callback : 0x%x\n", + OMAP_MCBSP_READ(mcbsp_dma_rx->io_base, SPCR2)); /* We can free the channels */ omap_free_dma(mcbsp_dma_rx->dma_rx_lch); @@ -146,19 +118,24 @@ static void omap_mcbsp_rx_dma_callback(int lch, u16 ch_status, void *data) complete(&mcbsp_dma_rx->rx_dma_completion); } - /* * omap_mcbsp_config simply write a config to the * appropriate McBSP. * You either call this function or set the McBSP registers * by yourself before calling omap_mcbsp_start(). */ - -void omap_mcbsp_config(unsigned int id, const struct omap_mcbsp_reg_cfg * config) +void omap_mcbsp_config(unsigned int id, const struct omap_mcbsp_reg_cfg *config) { - u32 io_base = mcbsp[id].io_base; + u32 io_base; + + if (!omap_mcbsp_check_valid_id(id)) { + printk(KERN_ERR "%s: Invalid id (%d)\n", __func__, id + 1); + return; + } - DBG("OMAP-McBSP: McBSP%d io_base: 0x%8x\n", id+1, io_base); + io_base = mcbsp[id].io_base; + dev_dbg(mcbsp[id].dev, "Configuring McBSP%d io_base: 0x%8x\n", + mcbsp[id].id, io_base); /* We write the given config */ OMAP_MCBSP_WRITE(io_base, SPCR2, config->spcr2); @@ -173,83 +150,7 @@ void omap_mcbsp_config(unsigned int id, const struct omap_mcbsp_reg_cfg * config OMAP_MCBSP_WRITE(io_base, MCR1, config->mcr1); OMAP_MCBSP_WRITE(io_base, PCR0, config->pcr0); } - - - -static int omap_mcbsp_check(unsigned int id) -{ - if (cpu_is_omap730()) { - if (id > OMAP_MAX_MCBSP_COUNT - 1) { - printk(KERN_ERR "OMAP-McBSP: McBSP%d doesn't exist\n", id + 1); - return -1; - } - return 0; - } - - if (cpu_is_omap15xx() || cpu_is_omap16xx() || cpu_is_omap24xx()) { - if (id > OMAP_MAX_MCBSP_COUNT) { - printk(KERN_ERR "OMAP-McBSP: McBSP%d doesn't exist\n", id + 1); - return -1; - } - return 0; - } - - return -1; -} - -#ifdef CONFIG_ARCH_OMAP1 -static void omap_mcbsp_dsp_request(void) -{ - if (cpu_is_omap15xx() || cpu_is_omap16xx()) { - int ret; - - ret = omap_dsp_request_mem(); - if (ret < 0) { - printk(KERN_ERR "Could not get dsp memory: %i\n", ret); - return; - } - - clk_enable(mcbsp_dsp_ck); - clk_enable(mcbsp_api_ck); - - /* enable 12MHz clock to mcbsp 1 & 3 */ - clk_enable(mcbsp_dspxor_ck); - - /* - * DSP external peripheral reset - * FIXME: This should be moved to dsp code - */ - __raw_writew(__raw_readw(DSP_RSTCT2) | 1 | 1 << 1, - DSP_RSTCT2); - } -} - -static void omap_mcbsp_dsp_free(void) -{ - if (cpu_is_omap15xx() || cpu_is_omap16xx()) { - omap_dsp_release_mem(); - clk_disable(mcbsp_dspxor_ck); - clk_disable(mcbsp_dsp_ck); - clk_disable(mcbsp_api_ck); - } -} -#endif - -#ifdef CONFIG_ARCH_OMAP2 -static void omap2_mcbsp2_mux_setup(void) -{ - if (cpu_is_omap2420()) { - omap_cfg_reg(Y15_24XX_MCBSP2_CLKX); - omap_cfg_reg(R14_24XX_MCBSP2_FSX); - omap_cfg_reg(W15_24XX_MCBSP2_DR); - omap_cfg_reg(V15_24XX_MCBSP2_DX); - omap_cfg_reg(V14_24XX_GPIO117); - } - /* - * Need to add MUX settings for OMAP 2430 SDP - */ -} -#endif +EXPORT_SYMBOL(omap_mcbsp_config); /* * We can choose between IRQ based or polled IO. @@ -257,13 +158,16 @@ static void omap2_mcbsp2_mux_setup(void) */ int omap_mcbsp_set_io_type(unsigned int id, omap_mcbsp_io_type_t io_type) { - if (omap_mcbsp_check(id) < 0) - return -EINVAL; + if (!omap_mcbsp_check_valid_id(id)) { + printk(KERN_ERR "%s: Invalid id (%d)\n", __func__, id + 1); + return -ENODEV; + } spin_lock(&mcbsp[id].lock); if (!mcbsp[id].free) { - printk (KERN_ERR "OMAP-McBSP: McBSP%d is currently in use\n", id + 1); + dev_err(mcbsp[id].dev, "McBSP%d is currently in use\n", + mcbsp[id].id); spin_unlock(&mcbsp[id].lock); return -EINVAL; } @@ -274,38 +178,26 @@ int omap_mcbsp_set_io_type(unsigned int id, omap_mcbsp_io_type_t io_type) return 0; } +EXPORT_SYMBOL(omap_mcbsp_set_io_type); int omap_mcbsp_request(unsigned int id) { int err; - if (omap_mcbsp_check(id) < 0) - return -EINVAL; - -#ifdef CONFIG_ARCH_OMAP1 - /* - * On 1510, 1610 and 1710, McBSP1 and McBSP3 - * are DSP public peripherals. - */ - if (id == OMAP_MCBSP1 || id == OMAP_MCBSP3) - omap_mcbsp_dsp_request(); -#endif - -#ifdef CONFIG_ARCH_OMAP2 - if (cpu_is_omap24xx()) { - if (id == OMAP_MCBSP1) { - clk_enable(mcbsp1_ick); - clk_enable(mcbsp1_fck); - } else { - clk_enable(mcbsp2_ick); - clk_enable(mcbsp2_fck); - } + if (!omap_mcbsp_check_valid_id(id)) { + printk(KERN_ERR "%s: Invalid id (%d)\n", __func__, id + 1); + return -ENODEV; } -#endif + + if (mcbsp[id].pdata->ops->request) + mcbsp[id].pdata->ops->request(id); + + clk_enable(mcbsp[id].clk); spin_lock(&mcbsp[id].lock); if (!mcbsp[id].free) { - printk (KERN_ERR "OMAP-McBSP: McBSP%d is currently in use\n", id + 1); + dev_err(mcbsp[id].dev, "McBSP%d is currently in use\n", + mcbsp[id].id); spin_unlock(&mcbsp[id].lock); return -1; } @@ -315,24 +207,23 @@ int omap_mcbsp_request(unsigned int id) if (mcbsp[id].io_type == OMAP_MCBSP_IRQ_IO) { /* We need to get IRQs here */ - err = request_irq(mcbsp[id].tx_irq, omap_mcbsp_tx_irq_handler, 0, - "McBSP", - (void *) (&mcbsp[id])); + err = request_irq(mcbsp[id].tx_irq, omap_mcbsp_tx_irq_handler, + 0, "McBSP", (void *) (&mcbsp[id])); if (err != 0) { - printk(KERN_ERR "OMAP-McBSP: Unable to request TX IRQ %d for McBSP%d\n", - mcbsp[id].tx_irq, mcbsp[id].id); + dev_err(mcbsp[id].dev, "Unable to request TX IRQ %d " + "for McBSP%d\n", mcbsp[id].tx_irq, + mcbsp[id].id); return err; } init_completion(&(mcbsp[id].tx_irq_completion)); - - err = request_irq(mcbsp[id].rx_irq, omap_mcbsp_rx_irq_handler, 0, - "McBSP", - (void *) (&mcbsp[id])); + err = request_irq(mcbsp[id].rx_irq, omap_mcbsp_rx_irq_handler, + 0, "McBSP", (void *) (&mcbsp[id])); if (err != 0) { - printk(KERN_ERR "OMAP-McBSP: Unable to request RX IRQ %d for McBSP%d\n", - mcbsp[id].rx_irq, mcbsp[id].id); + dev_err(mcbsp[id].dev, "Unable to request RX IRQ %d " + "for McBSP%d\n", mcbsp[id].rx_irq, + mcbsp[id].id); free_irq(mcbsp[id].tx_irq, (void *) (&mcbsp[id])); return err; } @@ -341,36 +232,25 @@ int omap_mcbsp_request(unsigned int id) } return 0; - } +EXPORT_SYMBOL(omap_mcbsp_request); void omap_mcbsp_free(unsigned int id) { - if (omap_mcbsp_check(id) < 0) + if (!omap_mcbsp_check_valid_id(id)) { + printk(KERN_ERR "%s: Invalid id (%d)\n", __func__, id + 1); return; - -#ifdef CONFIG_ARCH_OMAP1 - if (cpu_class_is_omap1()) { - if (id == OMAP_MCBSP1 || id == OMAP_MCBSP3) - omap_mcbsp_dsp_free(); } -#endif - -#ifdef CONFIG_ARCH_OMAP2 - if (cpu_is_omap24xx()) { - if (id == OMAP_MCBSP1) { - clk_disable(mcbsp1_ick); - clk_disable(mcbsp1_fck); - } else { - clk_disable(mcbsp2_ick); - clk_disable(mcbsp2_fck); - } - } -#endif + + if (mcbsp[id].pdata->ops->free) + mcbsp[id].pdata->ops->free(id); + + clk_disable(mcbsp[id].clk); spin_lock(&mcbsp[id].lock); if (mcbsp[id].free) { - printk (KERN_ERR "OMAP-McBSP: McBSP%d was not reserved\n", id + 1); + dev_err(mcbsp[id].dev, "McBSP%d was not reserved\n", + mcbsp[id].id); spin_unlock(&mcbsp[id].lock); return; } @@ -384,6 +264,7 @@ void omap_mcbsp_free(unsigned int id) free_irq(mcbsp[id].tx_irq, (void *) (&mcbsp[id])); } } +EXPORT_SYMBOL(omap_mcbsp_free); /* * Here we start the McBSP, by enabling the sample @@ -395,13 +276,15 @@ void omap_mcbsp_start(unsigned int id) u32 io_base; u16 w; - if (omap_mcbsp_check(id) < 0) + if (!omap_mcbsp_check_valid_id(id)) { + printk(KERN_ERR "%s: Invalid id (%d)\n", __func__, id + 1); return; + } io_base = mcbsp[id].io_base; - mcbsp[id].rx_word_length = ((OMAP_MCBSP_READ(io_base, RCR1) >> 5) & 0x7); - mcbsp[id].tx_word_length = ((OMAP_MCBSP_READ(io_base, XCR1) >> 5) & 0x7); + mcbsp[id].rx_word_length = (OMAP_MCBSP_READ(io_base, RCR1) >> 5) & 0x7; + mcbsp[id].tx_word_length = (OMAP_MCBSP_READ(io_base, XCR1) >> 5) & 0x7; /* Start the sample generator */ w = OMAP_MCBSP_READ(io_base, SPCR2); @@ -422,20 +305,22 @@ void omap_mcbsp_start(unsigned int id) /* Dump McBSP Regs */ omap_mcbsp_dump_reg(id); - } +EXPORT_SYMBOL(omap_mcbsp_start); void omap_mcbsp_stop(unsigned int id) { u32 io_base; u16 w; - if (omap_mcbsp_check(id) < 0) + if (!omap_mcbsp_check_valid_id(id)) { + printk(KERN_ERR "%s: Invalid id (%d)\n", __func__, id + 1); return; + } io_base = mcbsp[id].io_base; - /* Reset transmitter */ + /* Reset transmitter */ w = OMAP_MCBSP_READ(io_base, SPCR2); OMAP_MCBSP_WRITE(io_base, SPCR2, w & ~(1)); @@ -447,12 +332,19 @@ void omap_mcbsp_stop(unsigned int id) w = OMAP_MCBSP_READ(io_base, SPCR2); OMAP_MCBSP_WRITE(io_base, SPCR2, w & ~(1 << 6)); } - +EXPORT_SYMBOL(omap_mcbsp_stop); /* polled mcbsp i/o operations */ int omap_mcbsp_pollwrite(unsigned int id, u16 buf) { - u32 base = mcbsp[id].io_base; + u32 base; + + if (!omap_mcbsp_check_valid_id(id)) { + printk(KERN_ERR "%s: Invalid id (%d)\n", __func__, id + 1); + return -ENODEV; + } + + base = mcbsp[id].io_base; writew(buf, base + OMAP_MCBSP_REG_DXR1); /* if frame sync error - clear the error */ if (readw(base + OMAP_MCBSP_REG_SPCR2) & XSYNC_ERR) { @@ -474,18 +366,27 @@ int omap_mcbsp_pollwrite(unsigned int id, u16 buf) (XRST), base + OMAP_MCBSP_REG_SPCR2); udelay(10); - printk(KERN_ERR - " Could not write to McBSP Register\n"); + dev_err(mcbsp[id].dev, "Could not write to" + " McBSP%d Register\n", mcbsp[id].id); return -2; } } } + return 0; } +EXPORT_SYMBOL(omap_mcbsp_pollwrite); -int omap_mcbsp_pollread(unsigned int id, u16 * buf) +int omap_mcbsp_pollread(unsigned int id, u16 *buf) { - u32 base = mcbsp[id].io_base; + u32 base; + + if (!omap_mcbsp_check_valid_id(id)) { + printk(KERN_ERR "%s: Invalid id (%d)\n", __func__, id + 1); + return -ENODEV; + } + + base = mcbsp[id].io_base; /* if frame sync error - clear the error */ if (readw(base + OMAP_MCBSP_REG_SPCR1) & RSYNC_ERR) { /* clear error */ @@ -506,15 +407,17 @@ int omap_mcbsp_pollread(unsigned int id, u16 * buf) (RRST), base + OMAP_MCBSP_REG_SPCR1); udelay(10); - printk(KERN_ERR - " Could not read from McBSP Register\n"); + dev_err(mcbsp[id].dev, "Could not read from" + " McBSP%d Register\n", mcbsp[id].id); return -2; } } } *buf = readw(base + OMAP_MCBSP_REG_DRR1); + return 0; } +EXPORT_SYMBOL(omap_mcbsp_pollread); /* * IRQ based word transmission. @@ -522,12 +425,15 @@ int omap_mcbsp_pollread(unsigned int id, u16 * buf) void omap_mcbsp_xmit_word(unsigned int id, u32 word) { u32 io_base; - omap_mcbsp_word_length word_length = mcbsp[id].tx_word_length; + omap_mcbsp_word_length word_length; - if (omap_mcbsp_check(id) < 0) + if (!omap_mcbsp_check_valid_id(id)) { + printk(KERN_ERR "%s: Invalid id (%d)\n", __func__, id + 1); return; + } io_base = mcbsp[id].io_base; + word_length = mcbsp[id].tx_word_length; wait_for_completion(&(mcbsp[id].tx_irq_completion)); @@ -535,16 +441,20 @@ void omap_mcbsp_xmit_word(unsigned int id, u32 word) OMAP_MCBSP_WRITE(io_base, DXR2, word >> 16); OMAP_MCBSP_WRITE(io_base, DXR1, word & 0xffff); } +EXPORT_SYMBOL(omap_mcbsp_xmit_word); u32 omap_mcbsp_recv_word(unsigned int id) { u32 io_base; u16 word_lsb, word_msb = 0; - omap_mcbsp_word_length word_length = mcbsp[id].rx_word_length; + omap_mcbsp_word_length word_length; - if (omap_mcbsp_check(id) < 0) - return -EINVAL; + if (!omap_mcbsp_check_valid_id(id)) { + printk(KERN_ERR "%s: Invalid id (%d)\n", __func__, id + 1); + return -ENODEV; + } + word_length = mcbsp[id].rx_word_length; io_base = mcbsp[id].io_base; wait_for_completion(&(mcbsp[id].rx_irq_completion)); @@ -555,15 +465,24 @@ u32 omap_mcbsp_recv_word(unsigned int id) return (word_lsb | (word_msb << 16)); } - +EXPORT_SYMBOL(omap_mcbsp_recv_word); int omap_mcbsp_spi_master_xmit_word_poll(unsigned int id, u32 word) { - u32 io_base = mcbsp[id].io_base; - omap_mcbsp_word_length tx_word_length = mcbsp[id].tx_word_length; - omap_mcbsp_word_length rx_word_length = mcbsp[id].rx_word_length; + u32 io_base; + omap_mcbsp_word_length tx_word_length; + omap_mcbsp_word_length rx_word_length; u16 spcr2, spcr1, attempts = 0, word_lsb, word_msb = 0; + if (!omap_mcbsp_check_valid_id(id)) { + printk(KERN_ERR "%s: Invalid id (%d)\n", __func__, id + 1); + return -ENODEV; + } + + io_base = mcbsp[id].io_base; + tx_word_length = mcbsp[id].tx_word_length; + rx_word_length = mcbsp[id].rx_word_length; + if (tx_word_length != rx_word_length) return -EINVAL; @@ -577,7 +496,8 @@ int omap_mcbsp_spi_master_xmit_word_poll(unsigned int id, u32 word) udelay(10); OMAP_MCBSP_WRITE(io_base, SPCR2, spcr2 | XRST); udelay(10); - printk("McBSP transmitter not ready\n"); + dev_err(mcbsp[id].dev, "McBSP%d transmitter not " + "ready\n", mcbsp[id].id); return -EAGAIN; } } @@ -597,7 +517,8 @@ int omap_mcbsp_spi_master_xmit_word_poll(unsigned int id, u32 word) udelay(10); OMAP_MCBSP_WRITE(io_base, SPCR1, spcr1 | RRST); udelay(10); - printk("McBSP receiver not ready\n"); + dev_err(mcbsp[id].dev, "McBSP%d receiver not " + "ready\n", mcbsp[id].id); return -EAGAIN; } } @@ -609,14 +530,24 @@ int omap_mcbsp_spi_master_xmit_word_poll(unsigned int id, u32 word) return 0; } +EXPORT_SYMBOL(omap_mcbsp_spi_master_xmit_word_poll); -int omap_mcbsp_spi_master_recv_word_poll(unsigned int id, u32 * word) +int omap_mcbsp_spi_master_recv_word_poll(unsigned int id, u32 *word) { - u32 io_base = mcbsp[id].io_base, clock_word = 0; - omap_mcbsp_word_length tx_word_length = mcbsp[id].tx_word_length; - omap_mcbsp_word_length rx_word_length = mcbsp[id].rx_word_length; + u32 io_base, clock_word = 0; + omap_mcbsp_word_length tx_word_length; + omap_mcbsp_word_length rx_word_length; u16 spcr2, spcr1, attempts = 0, word_lsb, word_msb = 0; + if (!omap_mcbsp_check_valid_id(id)) { + printk(KERN_ERR "%s: Invalid id (%d)\n", __func__, id + 1); + return -ENODEV; + } + + io_base = mcbsp[id].io_base; + tx_word_length = mcbsp[id].tx_word_length; + rx_word_length = mcbsp[id].rx_word_length; + if (tx_word_length != rx_word_length) return -EINVAL; @@ -630,7 +561,8 @@ int omap_mcbsp_spi_master_recv_word_poll(unsigned int id, u32 * word) udelay(10); OMAP_MCBSP_WRITE(io_base, SPCR2, spcr2 | XRST); udelay(10); - printk("McBSP transmitter not ready\n"); + dev_err(mcbsp[id].dev, "McBSP%d transmitter not " + "ready\n", mcbsp[id].id); return -EAGAIN; } } @@ -650,7 +582,8 @@ int omap_mcbsp_spi_master_recv_word_poll(unsigned int id, u32 * word) udelay(10); OMAP_MCBSP_WRITE(io_base, SPCR1, spcr1 | RRST); udelay(10); - printk("McBSP receiver not ready\n"); + dev_err(mcbsp[id].dev, "McBSP%d receiver not " + "ready\n", mcbsp[id].id); return -EAGAIN; } } @@ -664,7 +597,7 @@ int omap_mcbsp_spi_master_recv_word_poll(unsigned int id, u32 * word) return 0; } - +EXPORT_SYMBOL(omap_mcbsp_spi_master_recv_word_poll); /* * Simple DMA based buffer rx/tx routines. @@ -673,25 +606,32 @@ int omap_mcbsp_spi_master_recv_word_poll(unsigned int id, u32 * word) * For anything fancier, you should use your own customized DMA * routines and callbacks. */ -int omap_mcbsp_xmit_buffer(unsigned int id, dma_addr_t buffer, unsigned int length) +int omap_mcbsp_xmit_buffer(unsigned int id, dma_addr_t buffer, + unsigned int length) { int dma_tx_ch; int src_port = 0; int dest_port = 0; int sync_dev = 0; - if (omap_mcbsp_check(id) < 0) - return -EINVAL; + if (!omap_mcbsp_check_valid_id(id)) { + printk(KERN_ERR "%s: Invalid id (%d)\n", __func__, id + 1); + return -ENODEV; + } - if (omap_request_dma(mcbsp[id].dma_tx_sync, "McBSP TX", omap_mcbsp_tx_dma_callback, - &mcbsp[id], - &dma_tx_ch)) { - printk("OMAP-McBSP: Unable to request DMA channel for McBSP%d TX. Trying IRQ based TX\n", id+1); + if (omap_request_dma(mcbsp[id].dma_tx_sync, "McBSP TX", + omap_mcbsp_tx_dma_callback, + &mcbsp[id], + &dma_tx_ch)) { + dev_err(mcbsp[id].dev, " Unable to request DMA channel for " + "McBSP%d TX. Trying IRQ based TX\n", + mcbsp[id].id); return -EAGAIN; } mcbsp[id].dma_tx_lch = dma_tx_ch; - DBG("TX DMA on channel %d\n", dma_tx_ch); + dev_err(mcbsp[id].dev, "McBSP%d TX DMA on channel %d\n", mcbsp[id].id, + dma_tx_ch); init_completion(&(mcbsp[id].tx_dma_completion)); @@ -699,7 +639,7 @@ int omap_mcbsp_xmit_buffer(unsigned int id, dma_addr_t buffer, unsigned int leng src_port = OMAP_DMA_PORT_TIPB; dest_port = OMAP_DMA_PORT_EMIFF; } - if (cpu_is_omap24xx()) + if (cpu_class_is_omap2()) sync_dev = mcbsp[id].dma_tx_sync; omap_set_dma_transfer_params(mcbsp[id].dma_tx_lch, @@ -722,29 +662,37 @@ int omap_mcbsp_xmit_buffer(unsigned int id, dma_addr_t buffer, unsigned int leng omap_start_dma(mcbsp[id].dma_tx_lch); wait_for_completion(&(mcbsp[id].tx_dma_completion)); + return 0; } +EXPORT_SYMBOL(omap_mcbsp_xmit_buffer); - -int omap_mcbsp_recv_buffer(unsigned int id, dma_addr_t buffer, unsigned int length) +int omap_mcbsp_recv_buffer(unsigned int id, dma_addr_t buffer, + unsigned int length) { int dma_rx_ch; int src_port = 0; int dest_port = 0; int sync_dev = 0; - if (omap_mcbsp_check(id) < 0) - return -EINVAL; + if (!omap_mcbsp_check_valid_id(id)) { + printk(KERN_ERR "%s: Invalid id (%d)\n", __func__, id + 1); + return -ENODEV; + } - if (omap_request_dma(mcbsp[id].dma_rx_sync, "McBSP RX", omap_mcbsp_rx_dma_callback, - &mcbsp[id], - &dma_rx_ch)) { - printk("Unable to request DMA channel for McBSP%d RX. Trying IRQ based RX\n", id+1); + if (omap_request_dma(mcbsp[id].dma_rx_sync, "McBSP RX", + omap_mcbsp_rx_dma_callback, + &mcbsp[id], + &dma_rx_ch)) { + dev_err(mcbsp[id].dev, "Unable to request DMA channel for " + "McBSP%d RX. Trying IRQ based RX\n", + mcbsp[id].id); return -EAGAIN; } mcbsp[id].dma_rx_lch = dma_rx_ch; - DBG("RX DMA on channel %d\n", dma_rx_ch); + dev_err(mcbsp[id].dev, "McBSP%d RX DMA on channel %d\n", mcbsp[id].id, + dma_rx_ch); init_completion(&(mcbsp[id].rx_dma_completion)); @@ -752,14 +700,14 @@ int omap_mcbsp_recv_buffer(unsigned int id, dma_addr_t buffer, unsigned int leng src_port = OMAP_DMA_PORT_TIPB; dest_port = OMAP_DMA_PORT_EMIFF; } - if (cpu_is_omap24xx()) + if (cpu_class_is_omap2()) sync_dev = mcbsp[id].dma_rx_sync; omap_set_dma_transfer_params(mcbsp[id].dma_rx_lch, - OMAP_DMA_DATA_TYPE_S16, - length >> 1, 1, - OMAP_DMA_SYNC_ELEMENT, - sync_dev, 0); + OMAP_DMA_DATA_TYPE_S16, + length >> 1, 1, + OMAP_DMA_SYNC_ELEMENT, + sync_dev, 0); omap_set_dma_src_params(mcbsp[id].dma_rx_lch, src_port, @@ -768,16 +716,17 @@ int omap_mcbsp_recv_buffer(unsigned int id, dma_addr_t buffer, unsigned int leng 0, 0); omap_set_dma_dest_params(mcbsp[id].dma_rx_lch, - dest_port, - OMAP_DMA_AMODE_POST_INC, - buffer, - 0, 0); + dest_port, + OMAP_DMA_AMODE_POST_INC, + buffer, + 0, 0); omap_start_dma(mcbsp[id].dma_rx_lch); wait_for_completion(&(mcbsp[id].rx_dma_completion)); + return 0; } - +EXPORT_SYMBOL(omap_mcbsp_recv_buffer); /* * SPI wrapper. @@ -785,12 +734,15 @@ int omap_mcbsp_recv_buffer(unsigned int id, dma_addr_t buffer, unsigned int leng * this wrapper just need an omap_mcbsp_spi_cfg structure as an input. * Once this is done, you can call omap_mcbsp_start(). */ -void omap_mcbsp_set_spi_mode(unsigned int id, const struct omap_mcbsp_spi_cfg * spi_cfg) +void omap_mcbsp_set_spi_mode(unsigned int id, + const struct omap_mcbsp_spi_cfg *spi_cfg) { struct omap_mcbsp_reg_cfg mcbsp_cfg; - if (omap_mcbsp_check(id) < 0) + if (!omap_mcbsp_check_valid_id(id)) { + printk(KERN_ERR "%s: Invalid id (%d)\n", __func__, id + 1); return; + } memset(&mcbsp_cfg, 0, sizeof(struct omap_mcbsp_reg_cfg)); @@ -798,7 +750,7 @@ void omap_mcbsp_set_spi_mode(unsigned int id, const struct omap_mcbsp_spi_cfg * mcbsp_cfg.rcr1 |= (RWDLEN1(spi_cfg->word_length) | RFRLEN1(0)); mcbsp_cfg.xcr1 |= (XWDLEN1(spi_cfg->word_length) | XFRLEN1(0)); - /* Clock stop mode */ + /* Clock stop mode */ if (spi_cfg->clk_stp_mode == OMAP_MCBSP_CLK_STP_MODE_NO_DELAY) mcbsp_cfg.spcr1 |= (1 << 12); else @@ -827,13 +779,12 @@ void omap_mcbsp_set_spi_mode(unsigned int id, const struct omap_mcbsp_spi_cfg * if (spi_cfg->spi_mode == OMAP_MCBSP_SPI_MASTER) { mcbsp_cfg.pcr0 |= CLKXM; - mcbsp_cfg.srgr1 |= CLKGDV(spi_cfg->clk_div -1); + mcbsp_cfg.srgr1 |= CLKGDV(spi_cfg->clk_div - 1); mcbsp_cfg.pcr0 |= FSXM; mcbsp_cfg.srgr2 &= ~FSGM; mcbsp_cfg.xcr2 |= XDATDLY(1); mcbsp_cfg.rcr2 |= RDATDLY(1); - } - else { + } else { mcbsp_cfg.pcr0 &= ~CLKXM; mcbsp_cfg.srgr1 |= CLKGDV(1); mcbsp_cfg.pcr0 &= ~FSXM; @@ -846,199 +797,99 @@ void omap_mcbsp_set_spi_mode(unsigned int id, const struct omap_mcbsp_spi_cfg * omap_mcbsp_config(id, &mcbsp_cfg); } - +EXPORT_SYMBOL(omap_mcbsp_set_spi_mode); /* * McBSP1 and McBSP3 are directly mapped on 1610 and 1510. * 730 has only 2 McBSP, and both of them are MPU peripherals. */ -struct omap_mcbsp_info { - u32 virt_base; - u8 dma_rx_sync, dma_tx_sync; - u16 rx_irq, tx_irq; -}; +static int __init omap_mcbsp_probe(struct platform_device *pdev) +{ + struct omap_mcbsp_platform_data *pdata = pdev->dev.platform_data; + int id = pdev->id - 1; + int ret = 0; -#ifdef CONFIG_ARCH_OMAP730 -static const struct omap_mcbsp_info mcbsp_730[] = { - [0] = { .virt_base = io_p2v(OMAP730_MCBSP1_BASE), - .dma_rx_sync = OMAP_DMA_MCBSP1_RX, - .dma_tx_sync = OMAP_DMA_MCBSP1_TX, - .rx_irq = INT_730_McBSP1RX, - .tx_irq = INT_730_McBSP1TX }, - [1] = { .virt_base = io_p2v(OMAP730_MCBSP2_BASE), - .dma_rx_sync = OMAP_DMA_MCBSP3_RX, - .dma_tx_sync = OMAP_DMA_MCBSP3_TX, - .rx_irq = INT_730_McBSP2RX, - .tx_irq = INT_730_McBSP2TX }, -}; -#endif - -#ifdef CONFIG_ARCH_OMAP15XX -static const struct omap_mcbsp_info mcbsp_1510[] = { - [0] = { .virt_base = OMAP1510_MCBSP1_BASE, - .dma_rx_sync = OMAP_DMA_MCBSP1_RX, - .dma_tx_sync = OMAP_DMA_MCBSP1_TX, - .rx_irq = INT_McBSP1RX, - .tx_irq = INT_McBSP1TX }, - [1] = { .virt_base = io_p2v(OMAP1510_MCBSP2_BASE), - .dma_rx_sync = OMAP_DMA_MCBSP2_RX, - .dma_tx_sync = OMAP_DMA_MCBSP2_TX, - .rx_irq = INT_1510_SPI_RX, - .tx_irq = INT_1510_SPI_TX }, - [2] = { .virt_base = OMAP1510_MCBSP3_BASE, - .dma_rx_sync = OMAP_DMA_MCBSP3_RX, - .dma_tx_sync = OMAP_DMA_MCBSP3_TX, - .rx_irq = INT_McBSP3RX, - .tx_irq = INT_McBSP3TX }, -}; -#endif - -#if defined(CONFIG_ARCH_OMAP16XX) -static const struct omap_mcbsp_info mcbsp_1610[] = { - [0] = { .virt_base = OMAP1610_MCBSP1_BASE, - .dma_rx_sync = OMAP_DMA_MCBSP1_RX, - .dma_tx_sync = OMAP_DMA_MCBSP1_TX, - .rx_irq = INT_McBSP1RX, - .tx_irq = INT_McBSP1TX }, - [1] = { .virt_base = io_p2v(OMAP1610_MCBSP2_BASE), - .dma_rx_sync = OMAP_DMA_MCBSP2_RX, - .dma_tx_sync = OMAP_DMA_MCBSP2_TX, - .rx_irq = INT_1610_McBSP2_RX, - .tx_irq = INT_1610_McBSP2_TX }, - [2] = { .virt_base = OMAP1610_MCBSP3_BASE, - .dma_rx_sync = OMAP_DMA_MCBSP3_RX, - .dma_tx_sync = OMAP_DMA_MCBSP3_TX, - .rx_irq = INT_McBSP3RX, - .tx_irq = INT_McBSP3TX }, -}; -#endif - -#if defined(CONFIG_ARCH_OMAP24XX) -static const struct omap_mcbsp_info mcbsp_24xx[] = { - [0] = { .virt_base = IO_ADDRESS(OMAP24XX_MCBSP1_BASE), - .dma_rx_sync = OMAP24XX_DMA_MCBSP1_RX, - .dma_tx_sync = OMAP24XX_DMA_MCBSP1_TX, - .rx_irq = INT_24XX_MCBSP1_IRQ_RX, - .tx_irq = INT_24XX_MCBSP1_IRQ_TX, - }, - [1] = { .virt_base = IO_ADDRESS(OMAP24XX_MCBSP2_BASE), - .dma_rx_sync = OMAP24XX_DMA_MCBSP2_RX, - .dma_tx_sync = OMAP24XX_DMA_MCBSP2_TX, - .rx_irq = INT_24XX_MCBSP2_IRQ_RX, - .tx_irq = INT_24XX_MCBSP2_IRQ_TX, - }, -}; -#endif + if (!pdata) { + dev_err(&pdev->dev, "McBSP device initialized without" + "platform data\n"); + ret = -EINVAL; + goto exit; + } + + dev_dbg(&pdev->dev, "Initializing OMAP McBSP (%d).\n", pdev->id); + + if (id >= OMAP_MAX_MCBSP_COUNT) { + dev_err(&pdev->dev, "Invalid McBSP device id (%d)\n", id); + ret = -EINVAL; + goto exit; + } + + spin_lock_init(&mcbsp[id].lock); + mcbsp[id].id = id + 1; + mcbsp[id].free = 1; + mcbsp[id].dma_tx_lch = -1; + mcbsp[id].dma_rx_lch = -1; + + mcbsp[id].io_base = pdata->virt_base; + /* Default I/O is IRQ based */ + mcbsp[id].io_type = OMAP_MCBSP_IRQ_IO; + mcbsp[id].tx_irq = pdata->tx_irq; + mcbsp[id].rx_irq = pdata->rx_irq; + mcbsp[id].dma_rx_sync = pdata->dma_rx_sync; + mcbsp[id].dma_tx_sync = pdata->dma_tx_sync; + + if (pdata->clk_name) + mcbsp[id].clk = clk_get(&pdev->dev, pdata->clk_name); + if (IS_ERR(mcbsp[id].clk)) { + mcbsp[id].free = 0; + dev_err(&pdev->dev, + "Invalid clock configuration for McBSP%d.\n", + mcbsp[id].id); + ret = -EINVAL; + goto exit; + } + + mcbsp[id].pdata = pdata; + mcbsp[id].dev = &pdev->dev; + platform_set_drvdata(pdev, &mcbsp[id]); + +exit: + return ret; +} -static int __init omap_mcbsp_init(void) +static int omap_mcbsp_remove(struct platform_device *pdev) { - int mcbsp_count = 0, i; - static const struct omap_mcbsp_info *mcbsp_info; + struct omap_mcbsp *mcbsp = platform_get_drvdata(pdev); - printk("Initializing OMAP McBSP system\n"); + platform_set_drvdata(pdev, NULL); + if (mcbsp) { -#ifdef CONFIG_ARCH_OMAP1 - mcbsp_dsp_ck = clk_get(0, "dsp_ck"); - if (IS_ERR(mcbsp_dsp_ck)) { - printk(KERN_ERR "mcbsp: could not acquire dsp_ck handle.\n"); - return PTR_ERR(mcbsp_dsp_ck); - } - mcbsp_api_ck = clk_get(0, "api_ck"); - if (IS_ERR(mcbsp_api_ck)) { - printk(KERN_ERR "mcbsp: could not acquire api_ck handle.\n"); - return PTR_ERR(mcbsp_api_ck); - } - mcbsp_dspxor_ck = clk_get(0, "dspxor_ck"); - if (IS_ERR(mcbsp_dspxor_ck)) { - printk(KERN_ERR "mcbsp: could not acquire dspxor_ck handle.\n"); - return PTR_ERR(mcbsp_dspxor_ck); - } -#endif -#ifdef CONFIG_ARCH_OMAP2 - mcbsp1_ick = clk_get(0, "mcbsp1_ick"); - if (IS_ERR(mcbsp1_ick)) { - printk(KERN_ERR "mcbsp: could not acquire mcbsp1_ick handle.\n"); - return PTR_ERR(mcbsp1_ick); - } - mcbsp1_fck = clk_get(0, "mcbsp1_fck"); - if (IS_ERR(mcbsp1_fck)) { - printk(KERN_ERR "mcbsp: could not acquire mcbsp1_fck handle.\n"); - return PTR_ERR(mcbsp1_fck); - } - mcbsp2_ick = clk_get(0, "mcbsp2_ick"); - if (IS_ERR(mcbsp2_ick)) { - printk(KERN_ERR "mcbsp: could not acquire mcbsp2_ick handle.\n"); - return PTR_ERR(mcbsp2_ick); - } - mcbsp2_fck = clk_get(0, "mcbsp2_fck"); - if (IS_ERR(mcbsp2_fck)) { - printk(KERN_ERR "mcbsp: could not acquire mcbsp2_fck handle.\n"); - return PTR_ERR(mcbsp2_fck); - } -#endif + if (mcbsp->pdata && mcbsp->pdata->ops && + mcbsp->pdata->ops->free) + mcbsp->pdata->ops->free(mcbsp->id); -#ifdef CONFIG_ARCH_OMAP730 - if (cpu_is_omap730()) { - mcbsp_info = mcbsp_730; - mcbsp_count = ARRAY_SIZE(mcbsp_730); - } -#endif -#ifdef CONFIG_ARCH_OMAP15XX - if (cpu_is_omap15xx()) { - mcbsp_info = mcbsp_1510; - mcbsp_count = ARRAY_SIZE(mcbsp_1510); - } -#endif -#if defined(CONFIG_ARCH_OMAP16XX) - if (cpu_is_omap16xx()) { - mcbsp_info = mcbsp_1610; - mcbsp_count = ARRAY_SIZE(mcbsp_1610); - } -#endif -#if defined(CONFIG_ARCH_OMAP24XX) - if (cpu_is_omap24xx()) { - mcbsp_info = mcbsp_24xx; - mcbsp_count = ARRAY_SIZE(mcbsp_24xx); - omap2_mcbsp2_mux_setup(); - } -#endif - for (i = 0; i < OMAP_MAX_MCBSP_COUNT ; i++) { - if (i >= mcbsp_count) { - mcbsp[i].io_base = 0; - mcbsp[i].free = 0; - continue; - } - mcbsp[i].id = i + 1; - mcbsp[i].free = 1; - mcbsp[i].dma_tx_lch = -1; - mcbsp[i].dma_rx_lch = -1; - - mcbsp[i].io_base = mcbsp_info[i].virt_base; - mcbsp[i].io_type = OMAP_MCBSP_IRQ_IO; /* Default I/O is IRQ based */ - mcbsp[i].tx_irq = mcbsp_info[i].tx_irq; - mcbsp[i].rx_irq = mcbsp_info[i].rx_irq; - mcbsp[i].dma_rx_sync = mcbsp_info[i].dma_rx_sync; - mcbsp[i].dma_tx_sync = mcbsp_info[i].dma_tx_sync; - spin_lock_init(&mcbsp[i].lock); + clk_disable(mcbsp->clk); + clk_put(mcbsp->clk); + + mcbsp->clk = NULL; + mcbsp->free = 0; + mcbsp->dev = NULL; } return 0; } -arch_initcall(omap_mcbsp_init); +static struct platform_driver omap_mcbsp_driver = { + .probe = omap_mcbsp_probe, + .remove = omap_mcbsp_remove, + .driver = { + .name = "omap-mcbsp", + }, +}; + +int __init omap_mcbsp_init(void) +{ + /* Register the McBSP driver */ + return platform_driver_register(&omap_mcbsp_driver); +} -EXPORT_SYMBOL(omap_mcbsp_config); -EXPORT_SYMBOL(omap_mcbsp_request); -EXPORT_SYMBOL(omap_mcbsp_set_io_type); -EXPORT_SYMBOL(omap_mcbsp_free); -EXPORT_SYMBOL(omap_mcbsp_start); -EXPORT_SYMBOL(omap_mcbsp_stop); -EXPORT_SYMBOL(omap_mcbsp_pollread); -EXPORT_SYMBOL(omap_mcbsp_pollwrite); -EXPORT_SYMBOL(omap_mcbsp_xmit_word); -EXPORT_SYMBOL(omap_mcbsp_recv_word); -EXPORT_SYMBOL(omap_mcbsp_xmit_buffer); -EXPORT_SYMBOL(omap_mcbsp_recv_buffer); -EXPORT_SYMBOL(omap_mcbsp_spi_master_xmit_word_poll); -EXPORT_SYMBOL(omap_mcbsp_spi_master_recv_word_poll); -EXPORT_SYMBOL(omap_mcbsp_set_spi_mode); diff --git a/arch/arm/plat-omap/sram.c b/arch/arm/plat-omap/sram.c index 1f23f0459e5..554ee58e129 100644 --- a/arch/arm/plat-omap/sram.c +++ b/arch/arm/plat-omap/sram.c @@ -10,6 +10,7 @@ * it under the terms of the GNU General Public License version 2 as * published by the Free Software Foundation. */ +#undef DEBUG #include <linux/module.h> #include <linux/kernel.h> @@ -24,25 +25,43 @@ #include <asm/arch/sram.h> #include <asm/arch/board.h> +#include <asm/arch/control.h> + +#if defined(CONFIG_ARCH_OMAP2) || defined(CONFIG_ARCH_OMAP3) +# include "../mach-omap2/prm.h" +# include "../mach-omap2/cm.h" +# include "../mach-omap2/sdrc.h" +#endif + #define OMAP1_SRAM_PA 0x20000000 -#define OMAP1_SRAM_VA 0xd0000000 +#define OMAP1_SRAM_VA VMALLOC_END #define OMAP2_SRAM_PA 0x40200000 #define OMAP2_SRAM_PUB_PA 0x4020f800 -#define OMAP2_SRAM_VA 0xd0000000 -#define OMAP2_SRAM_PUB_VA 0xd0000800 - -#if defined(CONFIG_ARCH_OMAP24XX) +#define OMAP2_SRAM_VA VMALLOC_END +#define OMAP2_SRAM_PUB_VA (VMALLOC_END + 0x800) +#define OMAP3_SRAM_PA 0x40200000 +#define OMAP3_SRAM_VA 0xd7000000 +#define OMAP3_SRAM_PUB_PA 0x40208000 +#define OMAP3_SRAM_PUB_VA 0xd7008000 + +#if defined(CONFIG_ARCH_OMAP24XX) || defined(CONFIG_ARCH_OMAP34XX) #define SRAM_BOOTLOADER_SZ 0x00 #else #define SRAM_BOOTLOADER_SZ 0x80 #endif -#define VA_REQINFOPERM0 IO_ADDRESS(0x68005048) -#define VA_READPERM0 IO_ADDRESS(0x68005050) -#define VA_WRITEPERM0 IO_ADDRESS(0x68005058) -#define VA_CONTROL_STAT IO_ADDRESS(0x480002F8) +#define OMAP24XX_VA_REQINFOPERM0 IO_ADDRESS(0x68005048) +#define OMAP24XX_VA_READPERM0 IO_ADDRESS(0x68005050) +#define OMAP24XX_VA_WRITEPERM0 IO_ADDRESS(0x68005058) + +#define OMAP34XX_VA_REQINFOPERM0 IO_ADDRESS(0x68012848) +#define OMAP34XX_VA_READPERM0 IO_ADDRESS(0x68012850) +#define OMAP34XX_VA_WRITEPERM0 IO_ADDRESS(0x68012858) +#define OMAP34XX_VA_ADDR_MATCH2 IO_ADDRESS(0x68012880) +#define OMAP34XX_VA_SMS_RG_ATT0 IO_ADDRESS(0x6C000048) +#define OMAP34XX_VA_CONTROL_STAT IO_ADDRESS(0x480022F0) + #define GP_DEVICE 0x300 -#define TYPE_MASK 0x700 #define ROUND_DOWN(value,boundary) ((value) & (~((boundary)-1))) @@ -68,14 +87,21 @@ static int is_sram_locked(void) int type = 0; if (cpu_is_omap242x()) - type = __raw_readl(VA_CONTROL_STAT) & TYPE_MASK; + type = system_rev & OMAP2_DEVICETYPE_MASK; if (type == GP_DEVICE) { /* RAMFW: R/W access to all initiators for all qualifier sets */ if (cpu_is_omap242x()) { - __raw_writel(0xFF, VA_REQINFOPERM0); /* all q-vects */ - __raw_writel(0xCFDE, VA_READPERM0); /* all i-read */ - __raw_writel(0xCFDE, VA_WRITEPERM0); /* all i-write */ + __raw_writel(0xFF, OMAP24XX_VA_REQINFOPERM0); /* all q-vects */ + __raw_writel(0xCFDE, OMAP24XX_VA_READPERM0); /* all i-read */ + __raw_writel(0xCFDE, OMAP24XX_VA_WRITEPERM0); /* all i-write */ + } + if (cpu_is_omap34xx()) { + __raw_writel(0xFFFF, OMAP34XX_VA_REQINFOPERM0); /* all q-vects */ + __raw_writel(0xFFFF, OMAP34XX_VA_READPERM0); /* all i-read */ + __raw_writel(0xFFFF, OMAP34XX_VA_WRITEPERM0); /* all i-write */ + __raw_writel(0x0, OMAP34XX_VA_ADDR_MATCH2); + __raw_writel(0xFFFFFFFF, OMAP34XX_VA_SMS_RG_ATT0); } return 0; } else @@ -92,18 +118,30 @@ void __init omap_detect_sram(void) { unsigned long reserved; - if (cpu_is_omap24xx()) { + if (cpu_class_is_omap2()) { if (is_sram_locked()) { - omap_sram_base = OMAP2_SRAM_PUB_VA; - omap_sram_start = OMAP2_SRAM_PUB_PA; - omap_sram_size = 0x800; /* 2K */ + if (cpu_is_omap34xx()) { + omap_sram_base = OMAP3_SRAM_PUB_VA; + omap_sram_start = OMAP3_SRAM_PUB_PA; + omap_sram_size = 0x8000; /* 32K */ + } else { + omap_sram_base = OMAP2_SRAM_PUB_VA; + omap_sram_start = OMAP2_SRAM_PUB_PA; + omap_sram_size = 0x800; /* 2K */ + } } else { - omap_sram_base = OMAP2_SRAM_VA; - omap_sram_start = OMAP2_SRAM_PA; - if (cpu_is_omap242x()) - omap_sram_size = 0xa0000; /* 640K */ - else if (cpu_is_omap243x()) + if (cpu_is_omap34xx()) { + omap_sram_base = OMAP3_SRAM_VA; + omap_sram_start = OMAP3_SRAM_PA; omap_sram_size = 0x10000; /* 64K */ + } else { + omap_sram_base = OMAP2_SRAM_VA; + omap_sram_start = OMAP2_SRAM_PA; + if (cpu_is_omap242x()) + omap_sram_size = 0xa0000; /* 640K */ + else if (cpu_is_omap243x()) + omap_sram_size = 0x10000; /* 64K */ + } } } else { omap_sram_base = OMAP1_SRAM_VA; @@ -157,6 +195,13 @@ void __init omap_map_sram(void) omap_sram_io_desc[0].pfn = __phys_to_pfn(base); } + if (cpu_is_omap34xx()) { + omap_sram_io_desc[0].virtual = OMAP3_SRAM_VA; + base = OMAP3_SRAM_PA; + base = ROUND_DOWN(base, PAGE_SIZE); + omap_sram_io_desc[0].pfn = __phys_to_pfn(base); + } + omap_sram_io_desc[0].length = 1024 * 1024; /* Use section desc */ iotable_init(omap_sram_io_desc, ARRAY_SIZE(omap_sram_io_desc)); @@ -191,6 +236,7 @@ void * omap_sram_push(void * start, unsigned long size) omap_sram_ceil -= size; omap_sram_ceil = ROUND_DOWN(omap_sram_ceil, sizeof(void *)); memcpy((void *)omap_sram_ceil, start, size); + flush_icache_range((unsigned long)start, (unsigned long)(start + size)); return (void *)omap_sram_ceil; } @@ -214,8 +260,9 @@ void omap_sram_reprogram_clock(u32 dpllctl, u32 ckctl) int __init omap1_sram_init(void) { - _omap_sram_reprogram_clock = omap_sram_push(sram_reprogram_clock, - sram_reprogram_clock_sz); + _omap_sram_reprogram_clock = + omap_sram_push(omap1_sram_reprogram_clock, + omap1_sram_reprogram_clock_sz); return 0; } @@ -224,7 +271,7 @@ int __init omap1_sram_init(void) #define omap1_sram_init() do {} while (0) #endif -#ifdef CONFIG_ARCH_OMAP2 +#if defined(CONFIG_ARCH_OMAP2) || defined(CONFIG_ARCH_OMAP3) static void (*_omap2_sram_ddr_init)(u32 *slow_dll_ctrl, u32 fast_dll_ctrl, u32 base_cs, u32 force_unlock); @@ -259,19 +306,109 @@ u32 omap2_set_prcm(u32 dpll_ctrl_val, u32 sdrc_rfr_val, int bypass) return _omap2_set_prcm(dpll_ctrl_val, sdrc_rfr_val, bypass); } +#endif + +#ifdef CONFIG_ARCH_OMAP2420 +int __init omap242x_sram_init(void) +{ + _omap2_sram_ddr_init = omap_sram_push(omap242x_sram_ddr_init, + omap242x_sram_ddr_init_sz); + + _omap2_sram_reprogram_sdrc = omap_sram_push(omap242x_sram_reprogram_sdrc, + omap242x_sram_reprogram_sdrc_sz); + + _omap2_set_prcm = omap_sram_push(omap242x_sram_set_prcm, + omap242x_sram_set_prcm_sz); + + return 0; +} +#else +static inline int omap242x_sram_init(void) +{ + return 0; +} +#endif + +#ifdef CONFIG_ARCH_OMAP2430 +int __init omap243x_sram_init(void) +{ + _omap2_sram_ddr_init = omap_sram_push(omap243x_sram_ddr_init, + omap243x_sram_ddr_init_sz); + + _omap2_sram_reprogram_sdrc = omap_sram_push(omap243x_sram_reprogram_sdrc, + omap243x_sram_reprogram_sdrc_sz); + + _omap2_set_prcm = omap_sram_push(omap243x_sram_set_prcm, + omap243x_sram_set_prcm_sz); + + return 0; +} +#else +static inline int omap243x_sram_init(void) +{ + return 0; +} +#endif + +#ifdef CONFIG_ARCH_OMAP3 + +static u32 (*_omap2_sram_reprogram_gpmc)(u32 perf_level); +u32 omap2_sram_reprogram_gpmc(u32 perf_level) +{ + if (!_omap2_sram_reprogram_gpmc) + omap_sram_error(); + + return _omap2_sram_reprogram_gpmc(perf_level); +} + +static u32 (*_omap2_sram_configure_core_dpll)(u32 m, u32 n, + u32 freqsel, u32 m2); +u32 omap2_sram_configure_core_dpll(u32 m, u32 n, u32 freqsel, u32 m2) +{ + if (!_omap2_sram_configure_core_dpll) + omap_sram_error(); + + return _omap2_sram_configure_core_dpll(m, n, freqsel, m2); +} -int __init omap2_sram_init(void) +/* REVISIT: Should this be same as omap34xx_sram_init() after off-idle? */ +void restore_sram_functions(void) { - _omap2_sram_ddr_init = omap_sram_push(sram_ddr_init, sram_ddr_init_sz); + omap_sram_ceil = omap_sram_base + omap_sram_size; - _omap2_sram_reprogram_sdrc = omap_sram_push(sram_reprogram_sdrc, - sram_reprogram_sdrc_sz); - _omap2_set_prcm = omap_sram_push(sram_set_prcm, sram_set_prcm_sz); + _omap2_sram_reprogram_gpmc = omap_sram_push(omap34xx_sram_reprogram_gpmc, + omap34xx_sram_reprogram_gpmc_sz); + + _omap2_sram_configure_core_dpll = + omap_sram_push(omap34xx_sram_configure_core_dpll, + omap34xx_sram_configure_core_dpll_sz); +} + +int __init omap34xx_sram_init(void) +{ + _omap2_sram_ddr_init = omap_sram_push(omap34xx_sram_ddr_init, + omap34xx_sram_ddr_init_sz); + + _omap2_sram_reprogram_sdrc = omap_sram_push(omap34xx_sram_reprogram_sdrc, + omap34xx_sram_reprogram_sdrc_sz); + + _omap2_set_prcm = omap_sram_push(omap34xx_sram_set_prcm, + omap34xx_sram_set_prcm_sz); + + _omap2_sram_reprogram_gpmc = omap_sram_push(omap34xx_sram_reprogram_gpmc, + omap34xx_sram_reprogram_gpmc_sz); + + _omap2_sram_configure_core_dpll = + omap_sram_push(omap34xx_sram_configure_core_dpll, + omap34xx_sram_configure_core_dpll_sz); return 0; } #else -#define omap2_sram_init() do {} while (0) +static inline int omap34xx_sram_init(void) +{ + return 0; +} #endif int __init omap_sram_init(void) @@ -279,10 +416,14 @@ int __init omap_sram_init(void) omap_detect_sram(); omap_map_sram(); - if (!cpu_is_omap24xx()) + if (!(cpu_class_is_omap2())) omap1_sram_init(); - else - omap2_sram_init(); + else if (cpu_is_omap242x()) + omap242x_sram_init(); + else if (cpu_is_omap2430()) + omap243x_sram_init(); + else if (cpu_is_omap34xx()) + omap34xx_sram_init(); return 0; } diff --git a/arch/arm/plat-omap/usb.c b/arch/arm/plat-omap/usb.c index a619475c4b7..2699c16d4da 100644 --- a/arch/arm/plat-omap/usb.c +++ b/arch/arm/plat-omap/usb.c @@ -1,4 +1,4 @@ -/* + /* * arch/arm/plat-omap/usb.c -- platform level USB initialization * * Copyright (C) 2004 Texas Instruments, Inc. @@ -156,8 +156,12 @@ static u32 __init omap_usb0_init(unsigned nwires, unsigned is_device) if (nwires == 0) { if (cpu_class_is_omap1() && !cpu_is_omap15xx()) { + u32 l; + /* pulldown D+/D- */ - USB_TRANSCEIVER_CTRL_REG &= ~(3 << 1); + l = omap_readl(USB_TRANSCEIVER_CTRL); + l &= ~(3 << 1); + omap_writel(l, USB_TRANSCEIVER_CTRL); } return 0; } @@ -171,6 +175,8 @@ static u32 __init omap_usb0_init(unsigned nwires, unsigned is_device) /* internal transceiver (unavailable on 17xx, 24xx) */ if (!cpu_class_is_omap2() && nwires == 2) { + u32 l; + // omap_cfg_reg(P9_USB_DP); // omap_cfg_reg(R8_USB_DM); @@ -185,9 +191,11 @@ static u32 __init omap_usb0_init(unsigned nwires, unsigned is_device) * - OTG support on this port not yet written */ - USB_TRANSCEIVER_CTRL_REG &= ~(7 << 4); + l = omap_readl(USB_TRANSCEIVER_CTRL); + l &= ~(7 << 4); if (!is_device) - USB_TRANSCEIVER_CTRL_REG |= (3 << 1); + l |= (3 << 1); + omap_writel(l, USB_TRANSCEIVER_CTRL); return 3 << 16; } @@ -217,8 +225,13 @@ static u32 __init omap_usb0_init(unsigned nwires, unsigned is_device) * with VBUS switching and overcurrent detection. */ - if (cpu_class_is_omap1() && nwires != 6) - USB_TRANSCEIVER_CTRL_REG &= ~CONF_USB2_UNI_R; + if (cpu_class_is_omap1() && nwires != 6) { + u32 l; + + l = omap_readl(USB_TRANSCEIVER_CTRL); + l &= ~CONF_USB2_UNI_R; + omap_writel(l, USB_TRANSCEIVER_CTRL); + } switch (nwires) { case 3: @@ -238,9 +251,13 @@ static u32 __init omap_usb0_init(unsigned nwires, unsigned is_device) omap_cfg_reg(K20_24XX_USB0_VM); omap2_usb_devconf_set(0, USB_UNIDIR); } else { + u32 l; + omap_cfg_reg(AA9_USB0_VP); omap_cfg_reg(R9_USB0_VM); - USB_TRANSCEIVER_CTRL_REG |= CONF_USB2_UNI_R; + l = omap_readl(USB_TRANSCEIVER_CTRL); + l |= CONF_USB2_UNI_R; + omap_writel(l, USB_TRANSCEIVER_CTRL); } break; default: @@ -254,8 +271,13 @@ static u32 __init omap_usb1_init(unsigned nwires) { u32 syscon1 = 0; - if (cpu_class_is_omap1() && !cpu_is_omap15xx() && nwires != 6) - USB_TRANSCEIVER_CTRL_REG &= ~CONF_USB1_UNI_R; + if (cpu_class_is_omap1() && !cpu_is_omap15xx() && nwires != 6) { + u32 l; + + l = omap_readl(USB_TRANSCEIVER_CTRL); + l &= ~CONF_USB1_UNI_R; + omap_writel(l, USB_TRANSCEIVER_CTRL); + } if (cpu_is_omap24xx()) omap2_usb_devconf_clear(1, USB_BIDIR_TLL); @@ -316,8 +338,13 @@ static u32 __init omap_usb1_init(unsigned nwires) syscon1 = 3; omap_cfg_reg(USB1_VP); omap_cfg_reg(USB1_VM); - if (!cpu_is_omap15xx()) - USB_TRANSCEIVER_CTRL_REG |= CONF_USB1_UNI_R; + if (!cpu_is_omap15xx()) { + u32 l; + + l = omap_readl(USB_TRANSCEIVER_CTRL); + l |= CONF_USB1_UNI_R; + omap_writel(l, USB_TRANSCEIVER_CTRL); + } break; default: bad: @@ -340,8 +367,13 @@ static u32 __init omap_usb2_init(unsigned nwires, unsigned alt_pingroup) if (alt_pingroup || nwires == 0) return 0; - if (cpu_class_is_omap1() && !cpu_is_omap15xx() && nwires != 6) - USB_TRANSCEIVER_CTRL_REG &= ~CONF_USB2_UNI_R; + if (cpu_class_is_omap1() && !cpu_is_omap15xx() && nwires != 6) { + u32 l; + + l = omap_readl(USB_TRANSCEIVER_CTRL); + l &= ~CONF_USB2_UNI_R; + omap_writel(l, USB_TRANSCEIVER_CTRL); + } /* external transceiver */ if (cpu_is_omap15xx()) { @@ -410,9 +442,13 @@ static u32 __init omap_usb2_init(unsigned nwires, unsigned alt_pingroup) omap_cfg_reg(USB2_VP); omap_cfg_reg(USB2_VM); } else { + u32 l; + omap_cfg_reg(AA9_USB2_VP); omap_cfg_reg(R9_USB2_VM); - USB_TRANSCEIVER_CTRL_REG |= CONF_USB2_UNI_R; + l = omap_readl(USB_TRANSCEIVER_CTRL); + l |= CONF_USB2_UNI_R; + omap_writel(l, USB_TRANSCEIVER_CTRL); } break; default: @@ -531,10 +567,6 @@ static struct platform_device otg_device = { /*-------------------------------------------------------------------------*/ -#define ULPD_CLOCK_CTRL_REG __REG16(ULPD_CLOCK_CTRL) -#define ULPD_SOFT_REQ_REG __REG16(ULPD_SOFT_REQ) - - // FIXME correct answer depends on hmc_mode, // as does (on omap1) any nonzero value for config->otg port number #ifdef CONFIG_USB_GADGET_OMAP @@ -550,17 +582,17 @@ static struct platform_device otg_device = { void __init omap_otg_init(struct omap_usb_config *config) { - u32 syscon = OTG_SYSCON_1_REG & 0xffff; + u32 syscon; int status; int alt_pingroup = 0; /* NOTE: no bus or clock setup (yet?) */ - syscon = OTG_SYSCON_1_REG & 0xffff; + syscon = omap_readl(OTG_SYSCON_1) & 0xffff; if (!(syscon & OTG_RESET_DONE)) pr_debug("USB resets not complete?\n"); - // OTG_IRQ_EN_REG = 0; + //omap_writew(0, OTG_IRQ_EN); /* pin muxing and transceiver pinouts */ if (config->pins[0] > 2) /* alt pingroup 2 */ @@ -568,8 +600,8 @@ omap_otg_init(struct omap_usb_config *config) syscon |= omap_usb0_init(config->pins[0], is_usb0_device(config)); syscon |= omap_usb1_init(config->pins[1]); syscon |= omap_usb2_init(config->pins[2], alt_pingroup); - pr_debug("OTG_SYSCON_1_REG = %08x\n", syscon); - OTG_SYSCON_1_REG = syscon; + pr_debug("OTG_SYSCON_1 = %08x\n", omap_readl(OTG_SYSCON_1)); + omap_writel(syscon, OTG_SYSCON_1); syscon = config->hmc_mode; syscon |= USBX_SYNCHRO | (4 << 16) /* B_ASE0_BRST */; @@ -578,9 +610,10 @@ omap_otg_init(struct omap_usb_config *config) syscon |= OTG_EN; #endif if (cpu_class_is_omap1()) - pr_debug("USB_TRANSCEIVER_CTRL_REG = %03x\n", USB_TRANSCEIVER_CTRL_REG); - pr_debug("OTG_SYSCON_2_REG = %08x\n", syscon); - OTG_SYSCON_2_REG = syscon; + pr_debug("USB_TRANSCEIVER_CTRL = %03x\n", + omap_readl(USB_TRANSCEIVER_CTRL)); + pr_debug("OTG_SYSCON_2 = %08x\n", omap_readl(OTG_SYSCON_2)); + omap_writel(syscon, OTG_SYSCON_2); printk("USB: hmc %d", config->hmc_mode); if (!alt_pingroup) @@ -597,12 +630,19 @@ omap_otg_init(struct omap_usb_config *config) printk("\n"); if (cpu_class_is_omap1()) { + u16 w; + /* leave USB clocks/controllers off until needed */ - ULPD_SOFT_REQ_REG &= ~SOFT_USB_CLK_REQ; - ULPD_CLOCK_CTRL_REG &= ~USB_MCLK_EN; - ULPD_CLOCK_CTRL_REG |= DIS_USB_PVCI_CLK; + w = omap_readw(ULPD_SOFT_REQ); + w &= ~SOFT_USB_CLK_REQ; + omap_writew(w, ULPD_SOFT_REQ); + + w = omap_readw(ULPD_CLOCK_CTRL); + w &= ~USB_MCLK_EN; + w |= DIS_USB_PVCI_CLK; + omap_writew(w, ULPD_CLOCK_CTRL); } - syscon = OTG_SYSCON_1_REG; + syscon = omap_readl(OTG_SYSCON_1); syscon |= HST_IDLE_EN|DEV_IDLE_EN|OTG_IDLE_EN; #ifdef CONFIG_USB_GADGET_OMAP @@ -639,8 +679,8 @@ omap_otg_init(struct omap_usb_config *config) pr_debug("can't register OTG device, %d\n", status); } #endif - pr_debug("OTG_SYSCON_1_REG = %08x\n", syscon); - OTG_SYSCON_1_REG = syscon; + pr_debug("OTG_SYSCON_1 = %08x\n", omap_readl(OTG_SYSCON_1)); + omap_writel(syscon, OTG_SYSCON_1); status = 0; } @@ -653,18 +693,19 @@ static inline void omap_otg_init(struct omap_usb_config *config) {} #ifdef CONFIG_ARCH_OMAP15XX -#define ULPD_DPLL_CTRL_REG __REG16(ULPD_DPLL_CTRL) +/* ULPD_DPLL_CTRL */ #define DPLL_IOB (1 << 13) #define DPLL_PLL_ENABLE (1 << 4) #define DPLL_LOCK (1 << 0) -#define ULPD_APLL_CTRL_REG __REG16(ULPD_APLL_CTRL) +/* ULPD_APLL_CTRL */ #define APLL_NDPLL_SWITCH (1 << 0) static void __init omap_1510_usb_init(struct omap_usb_config *config) { unsigned int val; + u16 w; omap_usb0_init(config->pins[0], is_usb0_device(config)); omap_usb1_init(config->pins[1]); @@ -685,12 +726,22 @@ static void __init omap_1510_usb_init(struct omap_usb_config *config) printk("\n"); /* use DPLL for 48 MHz function clock */ - pr_debug("APLL %04x DPLL %04x REQ %04x\n", ULPD_APLL_CTRL_REG, - ULPD_DPLL_CTRL_REG, ULPD_SOFT_REQ_REG); - ULPD_APLL_CTRL_REG &= ~APLL_NDPLL_SWITCH; - ULPD_DPLL_CTRL_REG |= DPLL_IOB | DPLL_PLL_ENABLE; - ULPD_SOFT_REQ_REG |= SOFT_UDC_REQ | SOFT_DPLL_REQ; - while (!(ULPD_DPLL_CTRL_REG & DPLL_LOCK)) + pr_debug("APLL %04x DPLL %04x REQ %04x\n", omap_readw(ULPD_APLL_CTRL), + omap_readw(ULPD_DPLL_CTRL), omap_readw(ULPD_SOFT_REQ)); + + w = omap_readw(ULPD_APLL_CTRL); + w &= ~APLL_NDPLL_SWITCH; + omap_writew(w, ULPD_APLL_CTRL); + + w = omap_readw(ULPD_DPLL_CTRL); + w |= DPLL_IOB | DPLL_PLL_ENABLE; + omap_writew(w, ULPD_DPLL_CTRL); + + w = omap_readw(ULPD_SOFT_REQ); + w |= SOFT_UDC_REQ | SOFT_DPLL_REQ; + omap_writew(w, ULPD_SOFT_REQ); + + while (!(omap_readw(ULPD_DPLL_CTRL) & DPLL_LOCK)) cpu_relax(); #ifdef CONFIG_USB_GADGET_OMAP diff --git a/arch/arm/plat-orion/irq.c b/arch/arm/plat-orion/irq.c index c5b669d234b..fe66a183516 100644 --- a/arch/arm/plat-orion/irq.c +++ b/arch/arm/plat-orion/irq.c @@ -36,8 +36,8 @@ static void orion_irq_unmask(u32 irq) static struct irq_chip orion_irq_chip = { .name = "orion_irq", - .ack = orion_irq_mask, .mask = orion_irq_mask, + .mask_ack = orion_irq_mask, .unmask = orion_irq_unmask, }; @@ -59,6 +59,7 @@ void __init orion_irq_init(unsigned int irq_start, void __iomem *maskaddr) set_irq_chip(irq, &orion_irq_chip); set_irq_chip_data(irq, maskaddr); set_irq_handler(irq, handle_level_irq); + irq_desc[irq].status |= IRQ_LEVEL; set_irq_flags(irq, IRQF_VALID); } } diff --git a/arch/arm/plat-orion/pcie.c b/arch/arm/plat-orion/pcie.c index abfda53f180..ca32c60e14d 100644 --- a/arch/arm/plat-orion/pcie.c +++ b/arch/arm/plat-orion/pcie.c @@ -39,6 +39,7 @@ #define PCIE_CONF_DATA_OFF 0x18fc #define PCIE_MASK_OFF 0x1910 #define PCIE_CTRL_OFF 0x1a00 +#define PCIE_CTRL_X1_MODE 0x0001 #define PCIE_STAT_OFF 0x1a04 #define PCIE_STAT_DEV_OFFS 20 #define PCIE_STAT_DEV_MASK 0x1f @@ -62,6 +63,11 @@ int orion_pcie_link_up(void __iomem *base) return !(readl(base + PCIE_STAT_OFF) & PCIE_STAT_LINK_DOWN); } +int __init orion_pcie_x4_mode(void __iomem *base) +{ + return !(readl(base + PCIE_CTRL_OFF) & PCIE_CTRL_X1_MODE); +} + int orion_pcie_get_local_bus_nr(void __iomem *base) { u32 stat = readl(base + PCIE_STAT_OFF); diff --git a/arch/arm/plat-orion/time.c b/arch/arm/plat-orion/time.c index 28b5285446e..93c4ef9f006 100644 --- a/arch/arm/plat-orion/time.c +++ b/arch/arm/plat-orion/time.c @@ -74,7 +74,7 @@ orion_clkevt_next_event(unsigned long delta, struct clock_event_device *dev) /* * Clear and enable clockevent timer interrupt. */ - writel(~BRIDGE_INT_TIMER1, BRIDGE_CAUSE); + writel(BRIDGE_INT_TIMER1_CLR, BRIDGE_CAUSE); u = readl(BRIDGE_MASK); u |= BRIDGE_INT_TIMER1; @@ -138,7 +138,7 @@ orion_clkevt_mode(enum clock_event_mode mode, struct clock_event_device *dev) /* * ACK pending timer interrupt. */ - writel(~BRIDGE_INT_TIMER1, BRIDGE_CAUSE); + writel(BRIDGE_INT_TIMER1_CLR, BRIDGE_CAUSE); } local_irq_restore(flags); @@ -159,7 +159,7 @@ static irqreturn_t orion_timer_interrupt(int irq, void *dev_id) /* * ACK timer interrupt and call event handler. */ - writel(~BRIDGE_INT_TIMER1, BRIDGE_CAUSE); + writel(BRIDGE_INT_TIMER1_CLR, BRIDGE_CAUSE); orion_clkevt.event_handler(&orion_clkevt); return IRQ_HANDLED; diff --git a/arch/arm/plat-s3c24xx/Kconfig b/arch/arm/plat-s3c24xx/Kconfig index b66fb3c4e22..5e28c217b8c 100644 --- a/arch/arm/plat-s3c24xx/Kconfig +++ b/arch/arm/plat-s3c24xx/Kconfig @@ -9,6 +9,7 @@ config PLAT_S3C24XX depends on ARCH_S3C2410 default y if ARCH_S3C2410 select NO_IOPORT + select HAVE_GPIO_LIB help Base platform code for any Samsung S3C24XX device @@ -20,6 +21,13 @@ config CPU_S3C244X help Support for S3C2440 and S3C2442 Samsung Mobile CPU based systems. +config S3C24XX_PWM + bool "PWM device support" + select HAVE_PWM + help + Support for exporting the PWM timer blocks via the pwm device + system. + config PM_SIMTEC bool help diff --git a/arch/arm/plat-s3c24xx/Makefile b/arch/arm/plat-s3c24xx/Makefile index 131d20237dd..d82767b2b83 100644 --- a/arch/arm/plat-s3c24xx/Makefile +++ b/arch/arm/plat-s3c24xx/Makefile @@ -16,8 +16,10 @@ obj-y += cpu.o obj-y += irq.o obj-y += devs.o obj-y += gpio.o +obj-y += gpiolib.o obj-y += time.o obj-y += clock.o +obj-y += pwm-clock.o # Architecture dependant builds @@ -27,5 +29,6 @@ obj-$(CONFIG_CPU_S3C244X) += s3c244x-clock.o obj-$(CONFIG_PM_SIMTEC) += pm-simtec.o obj-$(CONFIG_PM) += pm.o obj-$(CONFIG_PM) += sleep.o +obj-$(CONFIG_HAVE_PWM) += pwm.o obj-$(CONFIG_S3C2410_DMA) += dma.o obj-$(CONFIG_MACH_SMDK) += common-smdk.o diff --git a/arch/arm/plat-s3c24xx/devs.c b/arch/arm/plat-s3c24xx/devs.c index e546e933b3f..eea3b32ff79 100644 --- a/arch/arm/plat-s3c24xx/devs.c +++ b/arch/arm/plat-s3c24xx/devs.c @@ -495,106 +495,6 @@ struct platform_device s3c_device_spi1 = { EXPORT_SYMBOL(s3c_device_spi1); -/* pwm timer blocks */ - -static struct resource s3c_timer0_resource[] = { - [0] = { - .start = S3C24XX_PA_TIMER + 0x0C, - .end = S3C24XX_PA_TIMER + 0x0C + 0xB, - .flags = IORESOURCE_MEM, - }, - [1] = { - .start = IRQ_TIMER0, - .end = IRQ_TIMER0, - .flags = IORESOURCE_IRQ, - } - -}; - -struct platform_device s3c_device_timer0 = { - .name = "s3c2410-timer", - .id = 0, - .num_resources = ARRAY_SIZE(s3c_timer0_resource), - .resource = s3c_timer0_resource, -}; - -EXPORT_SYMBOL(s3c_device_timer0); - -/* timer 1 */ - -static struct resource s3c_timer1_resource[] = { - [0] = { - .start = S3C24XX_PA_TIMER + 0x18, - .end = S3C24XX_PA_TIMER + 0x23, - .flags = IORESOURCE_MEM, - }, - [1] = { - .start = IRQ_TIMER1, - .end = IRQ_TIMER1, - .flags = IORESOURCE_IRQ, - } - -}; - -struct platform_device s3c_device_timer1 = { - .name = "s3c2410-timer", - .id = 1, - .num_resources = ARRAY_SIZE(s3c_timer1_resource), - .resource = s3c_timer1_resource, -}; - -EXPORT_SYMBOL(s3c_device_timer1); - -/* timer 2 */ - -static struct resource s3c_timer2_resource[] = { - [0] = { - .start = S3C24XX_PA_TIMER + 0x24, - .end = S3C24XX_PA_TIMER + 0x2F, - .flags = IORESOURCE_MEM, - }, - [1] = { - .start = IRQ_TIMER2, - .end = IRQ_TIMER2, - .flags = IORESOURCE_IRQ, - } - -}; - -struct platform_device s3c_device_timer2 = { - .name = "s3c2410-timer", - .id = 2, - .num_resources = ARRAY_SIZE(s3c_timer2_resource), - .resource = s3c_timer2_resource, -}; - -EXPORT_SYMBOL(s3c_device_timer2); - -/* timer 3 */ - -static struct resource s3c_timer3_resource[] = { - [0] = { - .start = S3C24XX_PA_TIMER + 0x30, - .end = S3C24XX_PA_TIMER + 0x3B, - .flags = IORESOURCE_MEM, - }, - [1] = { - .start = IRQ_TIMER3, - .end = IRQ_TIMER3, - .flags = IORESOURCE_IRQ, - } - -}; - -struct platform_device s3c_device_timer3 = { - .name = "s3c2410-timer", - .id = 3, - .num_resources = ARRAY_SIZE(s3c_timer3_resource), - .resource = s3c_timer3_resource, -}; - -EXPORT_SYMBOL(s3c_device_timer3); - #ifdef CONFIG_CPU_S3C2440 /* Camif Controller */ diff --git a/arch/arm/plat-s3c24xx/gpiolib.c b/arch/arm/plat-s3c24xx/gpiolib.c new file mode 100644 index 00000000000..825d8d0c5ca --- /dev/null +++ b/arch/arm/plat-s3c24xx/gpiolib.c @@ -0,0 +1,259 @@ +/* linux/arch/arm/plat-s3c24xx/gpiolib.c + * + * Copyright (c) 2008 Simtec Electronics + * http://armlinux.simtec.co.uk/ + * Ben Dooks <ben@simtec.co.uk> + * + * S3C24XX GPIOlib support + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License. +*/ + +#include <linux/kernel.h> +#include <linux/init.h> +#include <linux/module.h> +#include <linux/interrupt.h> +#include <linux/ioport.h> +#include <linux/io.h> +#include <linux/gpio.h> + +#include <asm/hardware.h> +#include <asm/irq.h> + +#include <asm/arch/regs-gpio.h> + +struct s3c24xx_gpio_chip { + struct gpio_chip chip; + void __iomem *base; +}; + +static inline struct s3c24xx_gpio_chip *to_s3c_chip(struct gpio_chip *gpc) +{ + return container_of(gpc, struct s3c24xx_gpio_chip, chip); +} + +/* these routines are exported for use by other parts of the platform + * and system support, but are not intended to be used directly by the + * drivers themsevles. + */ + +int s3c24xx_gpiolib_input(struct gpio_chip *chip, unsigned offset) +{ + struct s3c24xx_gpio_chip *ourchip = to_s3c_chip(chip); + void __iomem *base = ourchip->base; + unsigned long flags; + unsigned long con; + + local_irq_save(flags); + + con = __raw_readl(base + 0x00); + con &= ~(3 << (offset * 2)); + con |= (S3C2410_GPIO_OUTPUT & 0xf) << (offset * 2); + + __raw_writel(con, base + 0x00); + + local_irq_restore(flags); + return 0; +} + +int s3c24xx_gpiolib_output(struct gpio_chip *chip, + unsigned offset, int value) +{ + struct s3c24xx_gpio_chip *ourchip = to_s3c_chip(chip); + void __iomem *base = ourchip->base; + unsigned long flags; + unsigned long dat; + unsigned long con; + + local_irq_save(flags); + + dat = __raw_readl(base + 0x04); + dat &= ~(1 << offset); + if (value) + dat |= 1 << offset; + __raw_writel(dat, base + 0x04); + + con = __raw_readl(base + 0x00); + con &= ~(3 << (offset * 2)); + con |= (S3C2410_GPIO_OUTPUT & 0xf) << (offset * 2); + + __raw_writel(con, base + 0x00); + __raw_writel(dat, base + 0x04); + + local_irq_restore(flags); + return 0; +} + +void s3c24xx_gpiolib_set(struct gpio_chip *chip, unsigned offset, int value) +{ + struct s3c24xx_gpio_chip *ourchip = to_s3c_chip(chip); + void __iomem *base = ourchip->base; + unsigned long flags; + unsigned long dat; + + local_irq_save(flags); + + dat = __raw_readl(base + 0x04); + dat &= ~(1 << offset); + if (value) + dat |= 1 << offset; + __raw_writel(dat, base + 0x04); + + local_irq_restore(flags); +} + +int s3c24xx_gpiolib_get(struct gpio_chip *chip, unsigned offset) +{ + struct s3c24xx_gpio_chip *ourchip = to_s3c_chip(chip); + unsigned long val; + + val = __raw_readl(ourchip->base + 0x04); + val >>= offset; + val &= 1; + + return val; +} + +static int s3c24xx_gpiolib_banka_input(struct gpio_chip *chip, unsigned offset) +{ + return -EINVAL; +} + +static int s3c24xx_gpiolib_banka_output(struct gpio_chip *chip, + unsigned offset, int value) +{ + struct s3c24xx_gpio_chip *ourchip = to_s3c_chip(chip); + void __iomem *base = ourchip->base; + unsigned long flags; + unsigned long dat; + unsigned long con; + + local_irq_save(flags); + + con = __raw_readl(base + 0x00); + dat = __raw_readl(base + 0x04); + + dat &= ~(1 << offset); + if (value) + dat |= 1 << offset; + + __raw_writel(dat, base + 0x04); + + con &= ~(1 << offset); + + __raw_writel(con, base + 0x00); + __raw_writel(dat, base + 0x04); + + local_irq_restore(flags); + return 0; +} + + +struct s3c24xx_gpio_chip gpios[] = { + [0] = { + .base = S3C24XX_GPIO_BASE(S3C2410_GPA0), + .chip = { + .base = S3C2410_GPA0, + .owner = THIS_MODULE, + .label = "GPIOA", + .ngpio = 24, + .direction_input = s3c24xx_gpiolib_banka_input, + .direction_output = s3c24xx_gpiolib_banka_output, + .set = s3c24xx_gpiolib_set, + .get = s3c24xx_gpiolib_get, + }, + }, + [1] = { + .base = S3C24XX_GPIO_BASE(S3C2410_GPB0), + .chip = { + .base = S3C2410_GPB0, + .owner = THIS_MODULE, + .label = "GPIOB", + .ngpio = 16, + .direction_input = s3c24xx_gpiolib_input, + .direction_output = s3c24xx_gpiolib_output, + .set = s3c24xx_gpiolib_set, + .get = s3c24xx_gpiolib_get, + }, + }, + [2] = { + .base = S3C24XX_GPIO_BASE(S3C2410_GPC0), + .chip = { + .base = S3C2410_GPC0, + .owner = THIS_MODULE, + .label = "GPIOC", + .ngpio = 16, + .direction_input = s3c24xx_gpiolib_input, + .direction_output = s3c24xx_gpiolib_output, + .set = s3c24xx_gpiolib_set, + .get = s3c24xx_gpiolib_get, + }, + }, + [3] = { + .base = S3C24XX_GPIO_BASE(S3C2410_GPD0), + .chip = { + .base = S3C2410_GPD0, + .owner = THIS_MODULE, + .label = "GPIOD", + .ngpio = 16, + .direction_input = s3c24xx_gpiolib_input, + .direction_output = s3c24xx_gpiolib_output, + .set = s3c24xx_gpiolib_set, + .get = s3c24xx_gpiolib_get, + }, + }, + [4] = { + .base = S3C24XX_GPIO_BASE(S3C2410_GPE0), + .chip = { + .base = S3C2410_GPE0, + .label = "GPIOE", + .owner = THIS_MODULE, + .ngpio = 16, + .direction_input = s3c24xx_gpiolib_input, + .direction_output = s3c24xx_gpiolib_output, + .set = s3c24xx_gpiolib_set, + .get = s3c24xx_gpiolib_get, + }, + }, + [5] = { + .base = S3C24XX_GPIO_BASE(S3C2410_GPF0), + .chip = { + .base = S3C2410_GPF0, + .owner = THIS_MODULE, + .label = "GPIOF", + .ngpio = 8, + .direction_input = s3c24xx_gpiolib_input, + .direction_output = s3c24xx_gpiolib_output, + .set = s3c24xx_gpiolib_set, + .get = s3c24xx_gpiolib_get, + }, + }, + [6] = { + .base = S3C24XX_GPIO_BASE(S3C2410_GPG0), + .chip = { + .base = S3C2410_GPG0, + .owner = THIS_MODULE, + .label = "GPIOG", + .ngpio = 10, + .direction_input = s3c24xx_gpiolib_input, + .direction_output = s3c24xx_gpiolib_output, + .set = s3c24xx_gpiolib_set, + .get = s3c24xx_gpiolib_get, + }, + }, +}; + +static __init int s3c24xx_gpiolib_init(void) +{ + struct s3c24xx_gpio_chip *chip = gpios; + int gpn; + + for (gpn = 0; gpn < ARRAY_SIZE(gpios); gpn++, chip++) + gpiochip_add(&chip->chip); + + return 0; +} + +arch_initcall(s3c24xx_gpiolib_init); diff --git a/arch/arm/plat-s3c24xx/pwm-clock.c b/arch/arm/plat-s3c24xx/pwm-clock.c new file mode 100644 index 00000000000..2cda3e3c678 --- /dev/null +++ b/arch/arm/plat-s3c24xx/pwm-clock.c @@ -0,0 +1,437 @@ +/* linux/arch/arm/plat-s3c24xx/pwm-clock.c + * + * Copyright (c) 2007 Simtec Electronics + * Copyright (c) 2007, 2008 Ben Dooks + * Ben Dooks <ben-linux@fluff.org> + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License. +*/ + +#include <linux/init.h> +#include <linux/module.h> +#include <linux/kernel.h> +#include <linux/list.h> +#include <linux/errno.h> +#include <linux/clk.h> +#include <linux/err.h> +#include <linux/io.h> + +#include <asm/hardware.h> +#include <asm/irq.h> + +#include <asm/arch/regs-clock.h> +#include <asm/arch/regs-gpio.h> + +#include <asm/plat-s3c24xx/clock.h> +#include <asm/plat-s3c24xx/cpu.h> + +#include <asm/plat-s3c/regs-timer.h> + +/* Each of the timers 0 through 5 go through the following + * clock tree, with the inputs depending on the timers. + * + * pclk ---- [ prescaler 0 ] -+---> timer 0 + * +---> timer 1 + * + * pclk ---- [ prescaler 1 ] -+---> timer 2 + * +---> timer 3 + * \---> timer 4 + * + * Which are fed into the timers as so: + * + * prescaled 0 ---- [ div 2,4,8,16 ] ---\ + * [mux] -> timer 0 + * tclk 0 ------------------------------/ + * + * prescaled 0 ---- [ div 2,4,8,16 ] ---\ + * [mux] -> timer 1 + * tclk 0 ------------------------------/ + * + * + * prescaled 1 ---- [ div 2,4,8,16 ] ---\ + * [mux] -> timer 2 + * tclk 1 ------------------------------/ + * + * prescaled 1 ---- [ div 2,4,8,16 ] ---\ + * [mux] -> timer 3 + * tclk 1 ------------------------------/ + * + * prescaled 1 ---- [ div 2,4,8, 16 ] --\ + * [mux] -> timer 4 + * tclk 1 ------------------------------/ + * + * Since the mux and the divider are tied together in the + * same register space, it is impossible to set the parent + * and the rate at the same time. To avoid this, we add an + * intermediate 'prescaled-and-divided' clock to select + * as the parent for the timer input clock called tdiv. + * + * prescaled clk --> pwm-tdiv ---\ + * [ mux ] --> timer X + * tclk -------------------------/ +*/ + +static unsigned long clk_pwm_scaler_getrate(struct clk *clk) +{ + unsigned long tcfg0 = __raw_readl(S3C2410_TCFG0); + + if (clk->id == 1) { + tcfg0 &= S3C2410_TCFG_PRESCALER1_MASK; + tcfg0 >>= S3C2410_TCFG_PRESCALER1_SHIFT; + } else { + tcfg0 &= S3C2410_TCFG_PRESCALER0_MASK; + } + + return clk_get_rate(clk->parent) / (tcfg0 + 1); +} + +/* TODO - add set rate calls. */ + +struct clk clk_timer_scaler[] = { + [0] = { + .name = "pwm-scaler0", + .id = -1, + .get_rate = clk_pwm_scaler_getrate, + }, + [1] = { + .name = "pwm-scaler1", + .id = -1, + .get_rate = clk_pwm_scaler_getrate, + }, +}; + +struct clk clk_timer_tclk[] = { + [0] = { + .name = "pwm-tclk0", + .id = -1, + }, + [1] = { + .name = "pwm-tclk1", + .id = -1, + }, +}; + +struct pwm_tdiv_clk { + struct clk clk; + unsigned int divisor; +}; + +static inline struct pwm_tdiv_clk *to_tdiv(struct clk *clk) +{ + return container_of(clk, struct pwm_tdiv_clk, clk); +} + +static inline unsigned long tcfg_to_divisor(unsigned long tcfg1) +{ + return 1 << (1 + tcfg1); +} + +static unsigned long clk_pwm_tdiv_get_rate(struct clk *clk) +{ + unsigned long tcfg1 = __raw_readl(S3C2410_TCFG1); + unsigned int divisor; + + tcfg1 >>= S3C2410_TCFG1_SHIFT(clk->id); + tcfg1 &= S3C2410_TCFG1_MUX_MASK; + + if (tcfg1 == S3C2410_TCFG1_MUX_TCLK) + divisor = to_tdiv(clk)->divisor; + else + divisor = tcfg_to_divisor(tcfg1); + + return clk_get_rate(clk->parent) / divisor; +} + +static unsigned long clk_pwm_tdiv_round_rate(struct clk *clk, + unsigned long rate) +{ + unsigned long parent_rate; + unsigned long divisor; + + parent_rate = clk_get_rate(clk->parent); + divisor = parent_rate / rate; + + if (divisor <= 2) + divisor = 2; + else if (divisor <= 4) + divisor = 4; + else if (divisor <= 8) + divisor = 8; + else + divisor = 16; + + return parent_rate / divisor; +} + +static unsigned long clk_pwm_tdiv_bits(struct pwm_tdiv_clk *divclk) +{ + unsigned long bits; + + switch (divclk->divisor) { + case 2: + bits = S3C2410_TCFG1_MUX_DIV2; + break; + case 4: + bits = S3C2410_TCFG1_MUX_DIV4; + break; + case 8: + bits = S3C2410_TCFG1_MUX_DIV8; + break; + case 16: + default: + bits = S3C2410_TCFG1_MUX_DIV16; + break; + } + + return bits; +} + +static void clk_pwm_tdiv_update(struct pwm_tdiv_clk *divclk) +{ + unsigned long tcfg1 = __raw_readl(S3C2410_TCFG1); + unsigned long bits = clk_pwm_tdiv_bits(divclk); + unsigned long flags; + unsigned long shift = S3C2410_TCFG1_SHIFT(divclk->clk.id); + + local_irq_save(flags); + + tcfg1 = __raw_readl(S3C2410_TCFG1); + tcfg1 &= ~(S3C2410_TCFG1_MUX_MASK << shift); + tcfg1 |= bits << shift; + __raw_writel(tcfg1, S3C2410_TCFG1); + + local_irq_restore(flags); +} + +static int clk_pwm_tdiv_set_rate(struct clk *clk, unsigned long rate) +{ + struct pwm_tdiv_clk *divclk = to_tdiv(clk); + unsigned long tcfg1 = __raw_readl(S3C2410_TCFG1); + unsigned long parent_rate = clk_get_rate(clk->parent); + unsigned long divisor; + + tcfg1 >>= S3C2410_TCFG1_SHIFT(clk->id); + tcfg1 &= S3C2410_TCFG1_MUX_MASK; + + rate = clk_round_rate(clk, rate); + divisor = parent_rate / rate; + + if (divisor > 16) + return -EINVAL; + + divclk->divisor = divisor; + + /* Update the current MUX settings if we are currently + * selected as the clock source for this clock. */ + + if (tcfg1 != S3C2410_TCFG1_MUX_TCLK) + clk_pwm_tdiv_update(divclk); + + return 0; +} + +struct pwm_tdiv_clk clk_timer_tdiv[] = { + [0] = { + .clk = { + .name = "pwm-tdiv", + .parent = &clk_timer_scaler[0], + .get_rate = clk_pwm_tdiv_get_rate, + .set_rate = clk_pwm_tdiv_set_rate, + .round_rate = clk_pwm_tdiv_round_rate, + }, + }, + [1] = { + .clk = { + .name = "pwm-tdiv", + .parent = &clk_timer_scaler[0], + .get_rate = clk_pwm_tdiv_get_rate, + .set_rate = clk_pwm_tdiv_set_rate, + .round_rate = clk_pwm_tdiv_round_rate, + } + }, + [2] = { + .clk = { + .name = "pwm-tdiv", + .parent = &clk_timer_scaler[1], + .get_rate = clk_pwm_tdiv_get_rate, + .set_rate = clk_pwm_tdiv_set_rate, + .round_rate = clk_pwm_tdiv_round_rate, + }, + }, + [3] = { + .clk = { + .name = "pwm-tdiv", + .parent = &clk_timer_scaler[1], + .get_rate = clk_pwm_tdiv_get_rate, + .set_rate = clk_pwm_tdiv_set_rate, + .round_rate = clk_pwm_tdiv_round_rate, + }, + }, + [4] = { + .clk = { + .name = "pwm-tdiv", + .parent = &clk_timer_scaler[1], + .get_rate = clk_pwm_tdiv_get_rate, + .set_rate = clk_pwm_tdiv_set_rate, + .round_rate = clk_pwm_tdiv_round_rate, + }, + }, +}; + +static int __init clk_pwm_tdiv_register(unsigned int id) +{ + struct pwm_tdiv_clk *divclk = &clk_timer_tdiv[id]; + unsigned long tcfg1 = __raw_readl(S3C2410_TCFG1); + + tcfg1 >>= S3C2410_TCFG1_SHIFT(id); + tcfg1 &= S3C2410_TCFG1_MUX_MASK; + + divclk->clk.id = id; + divclk->divisor = tcfg_to_divisor(tcfg1); + + return s3c24xx_register_clock(&divclk->clk); +} + +static inline struct clk *s3c24xx_pwmclk_tclk(unsigned int id) +{ + return (id >= 2) ? &clk_timer_tclk[1] : &clk_timer_tclk[0]; +} + +static inline struct clk *s3c24xx_pwmclk_tdiv(unsigned int id) +{ + return &clk_timer_tdiv[id].clk; +} + +static int clk_pwm_tin_set_parent(struct clk *clk, struct clk *parent) +{ + unsigned int id = clk->id; + unsigned long tcfg1; + unsigned long flags; + unsigned long bits; + unsigned long shift = S3C2410_TCFG1_SHIFT(id); + + if (parent == s3c24xx_pwmclk_tclk(id)) + bits = S3C2410_TCFG1_MUX_TCLK << shift; + else if (parent == s3c24xx_pwmclk_tdiv(id)) + bits = clk_pwm_tdiv_bits(to_tdiv(clk)) << shift; + else + return -EINVAL; + + clk->parent = parent; + + local_irq_save(flags); + + tcfg1 = __raw_readl(S3C2410_TCFG1); + tcfg1 &= ~(S3C2410_TCFG1_MUX_MASK << shift); + __raw_writel(tcfg1 | bits, S3C2410_TCFG1); + + local_irq_restore(flags); + + return 0; +} + +static struct clk clk_tin[] = { + [0] = { + .name = "pwm-tin", + .id = 0, + .set_parent = clk_pwm_tin_set_parent, + }, + [1] = { + .name = "pwm-tin", + .id = 1, + .set_parent = clk_pwm_tin_set_parent, + }, + [2] = { + .name = "pwm-tin", + .id = 2, + .set_parent = clk_pwm_tin_set_parent, + }, + [3] = { + .name = "pwm-tin", + .id = 3, + .set_parent = clk_pwm_tin_set_parent, + }, + [4] = { + .name = "pwm-tin", + .id = 4, + .set_parent = clk_pwm_tin_set_parent, + }, +}; + +static __init int clk_pwm_tin_register(struct clk *pwm) +{ + unsigned long tcfg1 = __raw_readl(S3C2410_TCFG1); + unsigned int id = pwm->id; + + struct clk *parent; + int ret; + + ret = s3c24xx_register_clock(pwm); + if (ret < 0) + return ret; + + tcfg1 >>= S3C2410_TCFG1_SHIFT(id); + tcfg1 &= S3C2410_TCFG1_MUX_MASK; + + if (tcfg1 == S3C2410_TCFG1_MUX_TCLK) + parent = s3c24xx_pwmclk_tclk(id); + else + parent = s3c24xx_pwmclk_tdiv(id); + + return clk_set_parent(pwm, parent); +} + +static __init int s3c24xx_pwmclk_init(void) +{ + struct clk *clk_timers; + unsigned int clk; + int ret; + + clk_timers = clk_get(NULL, "timers"); + if (IS_ERR(clk_timers)) { + printk(KERN_ERR "%s: no parent clock\n", __func__); + return -EINVAL; + } + + for (clk = 0; clk < ARRAY_SIZE(clk_timer_scaler); clk++) { + clk_timer_scaler[clk].parent = clk_timers; + ret = s3c24xx_register_clock(&clk_timer_scaler[clk]); + if (ret < 0) { + printk(KERN_ERR "error adding pwm scaler%d clock\n", clk); + goto err; + } + } + + for (clk = 0; clk < ARRAY_SIZE(clk_timer_tclk); clk++) { + ret = s3c24xx_register_clock(&clk_timer_tclk[clk]); + if (ret < 0) { + printk(KERN_ERR "error adding pww tclk%d\n", clk); + goto err; + } + } + + for (clk = 0; clk < ARRAY_SIZE(clk_timer_tdiv); clk++) { + ret = clk_pwm_tdiv_register(clk); + if (ret < 0) { + printk(KERN_ERR "error adding pwm%d tdiv clock\n", clk); + goto err; + } + } + + for (clk = 0; clk < ARRAY_SIZE(clk_tin); clk++) { + ret = clk_pwm_tin_register(&clk_tin[clk]); + if (ret < 0) { + printk(KERN_ERR "error adding pwm%d tin clock\n", clk); + goto err; + } + } + + return 0; + + err: + return ret; +} + +arch_initcall(s3c24xx_pwmclk_init); diff --git a/arch/arm/plat-s3c24xx/pwm.c b/arch/arm/plat-s3c24xx/pwm.c new file mode 100644 index 00000000000..18c4bdc49a0 --- /dev/null +++ b/arch/arm/plat-s3c24xx/pwm.c @@ -0,0 +1,402 @@ +/* arch/arm/plat-s3c24xx/pwm.c + * + * Copyright (c) 2007 Ben Dooks + * Copyright (c) 2008 Simtec Electronics + * Ben Dooks <ben@simtec.co.uk>, <ben-linux@fluff.org> + * + * S3C24XX PWM device core + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License. +*/ + +#include <linux/module.h> +#include <linux/kernel.h> +#include <linux/platform_device.h> +#include <linux/err.h> +#include <linux/clk.h> +#include <linux/io.h> +#include <linux/pwm.h> + +#include <asm/plat-s3c/regs-timer.h> + +struct pwm_device { + struct list_head list; + struct platform_device *pdev; + + struct clk *clk_div; + struct clk *clk; + const char *label; + + unsigned int period_ns; + unsigned int duty_ns; + + unsigned char tcon_base; + unsigned char running; + unsigned char use_count; + unsigned char pwm_id; +}; + +#define pwm_dbg(_pwm, msg...) dev_info(&(_pwm)->pdev->dev, msg) + +static struct clk *clk_scaler[2]; + +/* Standard setup for a timer block. */ + +#define TIMER_RESOURCE_SIZE (1) + +#define TIMER_RESOURCE(_tmr, _irq) \ + (struct resource [TIMER_RESOURCE_SIZE]) { \ + [0] = { \ + .start = _irq, \ + .end = _irq, \ + .flags = IORESOURCE_IRQ \ + } \ + } + +#define DEFINE_TIMER(_tmr_no, _irq) \ + .name = "s3c24xx-pwm", \ + .id = _tmr_no, \ + .num_resources = TIMER_RESOURCE_SIZE, \ + .resource = TIMER_RESOURCE(_tmr_no, _irq), \ + +/* since we already have an static mapping for the timer, we do not + * bother setting any IO resource for the base. + */ + +struct platform_device s3c_device_timer[] = { + [0] = { DEFINE_TIMER(0, IRQ_TIMER0) }, + [1] = { DEFINE_TIMER(1, IRQ_TIMER1) }, + [2] = { DEFINE_TIMER(2, IRQ_TIMER2) }, + [3] = { DEFINE_TIMER(3, IRQ_TIMER3) }, + [4] = { DEFINE_TIMER(4, IRQ_TIMER4) }, +}; + +static inline int pwm_is_tdiv(struct pwm_device *pwm) +{ + return clk_get_parent(pwm->clk) == pwm->clk_div; +} + +static DEFINE_MUTEX(pwm_lock); +static LIST_HEAD(pwm_list); + +struct pwm_device *pwm_request(int pwm_id, const char *label) +{ + struct pwm_device *pwm; + int found = 0; + + mutex_lock(&pwm_lock); + + list_for_each_entry(pwm, &pwm_list, list) { + if (pwm->pwm_id == pwm_id) { + found = 1; + break; + } + } + + if (found) { + if (pwm->use_count == 0) { + pwm->use_count = 1; + pwm->label = label; + } else + pwm = ERR_PTR(-EBUSY); + } else + pwm = ERR_PTR(-ENOENT); + + mutex_unlock(&pwm_lock); + return pwm; +} + +EXPORT_SYMBOL(pwm_request); + + +void pwm_free(struct pwm_device *pwm) +{ + mutex_lock(&pwm_lock); + + if (pwm->use_count) { + pwm->use_count--; + pwm->label = NULL; + } else + printk(KERN_ERR "PWM%d device already freed\n", pwm->pwm_id); + + mutex_unlock(&pwm_lock); +} + +EXPORT_SYMBOL(pwm_free); + +#define pwm_tcon_start(pwm) (1 << (pwm->tcon_base + 0)) +#define pwm_tcon_invert(pwm) (1 << (pwm->tcon_base + 2)) +#define pwm_tcon_autoreload(pwm) (1 << (pwm->tcon_base + 3)) +#define pwm_tcon_manulupdate(pwm) (1 << (pwm->tcon_base + 1)) + +int pwm_enable(struct pwm_device *pwm) +{ + unsigned long flags; + unsigned long tcon; + + local_irq_save(flags); + + tcon = __raw_readl(S3C2410_TCON); + tcon |= pwm_tcon_start(pwm); + __raw_writel(tcon, S3C2410_TCON); + + local_irq_restore(flags); + + pwm->running = 1; + return 0; +} + +EXPORT_SYMBOL(pwm_enable); + +void pwm_disable(struct pwm_device *pwm) +{ + unsigned long flags; + unsigned long tcon; + + local_irq_save(flags); + + tcon = __raw_readl(S3C2410_TCON); + tcon &= ~pwm_tcon_start(pwm); + __raw_writel(tcon, S3C2410_TCON); + + local_irq_restore(flags); + + pwm->running = 0; +} + +EXPORT_SYMBOL(pwm_disable); + +unsigned long pwm_calc_tin(struct pwm_device *pwm, unsigned long freq) +{ + unsigned long tin_parent_rate; + unsigned int div; + + tin_parent_rate = clk_get_rate(clk_get_parent(pwm->clk_div)); + pwm_dbg(pwm, "tin parent at %lu\n", tin_parent_rate); + + for (div = 2; div <= 16; div *= 2) { + if ((tin_parent_rate / (div << 16)) < freq) + return tin_parent_rate / div; + } + + return tin_parent_rate / 16; +} + +#define NS_IN_HZ (1000000000UL) + +int pwm_config(struct pwm_device *pwm, int duty_ns, int period_ns) +{ + unsigned long tin_rate; + unsigned long tin_ns; + unsigned long period; + unsigned long flags; + unsigned long tcon; + unsigned long tcnt; + long tcmp; + + /* We currently avoid using 64bit arithmetic by using the + * fact that anything faster than 1Hz is easily representable + * by 32bits. */ + + if (period_ns > NS_IN_HZ || duty_ns > NS_IN_HZ) + return -ERANGE; + + if (duty_ns > period_ns) + return -EINVAL; + + if (period_ns == pwm->period_ns && + duty_ns == pwm->duty_ns) + return 0; + + /* The TCMP and TCNT can be read without a lock, they're not + * shared between the timers. */ + + tcmp = __raw_readl(S3C2410_TCMPB(pwm->pwm_id)); + tcnt = __raw_readl(S3C2410_TCNTB(pwm->pwm_id)); + + period = NS_IN_HZ / period_ns; + + pwm_dbg(pwm, "duty_ns=%d, period_ns=%d (%lu)\n", + duty_ns, period_ns, period); + + /* Check to see if we are changing the clock rate of the PWM */ + + if (pwm->period_ns != period_ns) { + if (pwm_is_tdiv(pwm)) { + tin_rate = pwm_calc_tin(pwm, period); + clk_set_rate(pwm->clk_div, tin_rate); + } else + tin_rate = clk_get_rate(pwm->clk); + + pwm->period_ns = period_ns; + + pwm_dbg(pwm, "tin_rate=%lu\n", tin_rate); + + tin_ns = NS_IN_HZ / tin_rate; + tcnt = period_ns / tin_ns; + } else + tin_ns = NS_IN_HZ / clk_get_rate(pwm->clk); + + /* Note, counters count down */ + + tcmp = duty_ns / tin_ns; + tcmp = tcnt - tcmp; + + pwm_dbg(pwm, "tin_ns=%lu, tcmp=%ld/%lu\n", tin_ns, tcmp, tcnt); + + if (tcmp < 0) + tcmp = 0; + + /* Update the PWM register block. */ + + local_irq_save(flags); + + __raw_writel(tcmp, S3C2410_TCMPB(pwm->pwm_id)); + __raw_writel(tcnt, S3C2410_TCNTB(pwm->pwm_id)); + + tcon = __raw_readl(S3C2410_TCON); + tcon |= pwm_tcon_manulupdate(pwm); + tcon |= pwm_tcon_autoreload(pwm); + __raw_writel(tcon, S3C2410_TCON); + + tcon &= ~pwm_tcon_manulupdate(pwm); + __raw_writel(tcon, S3C2410_TCON); + + local_irq_restore(flags); + + return 0; +} + +EXPORT_SYMBOL(pwm_config); + +static int pwm_register(struct pwm_device *pwm) +{ + pwm->duty_ns = -1; + pwm->period_ns = -1; + + mutex_lock(&pwm_lock); + list_add_tail(&pwm->list, &pwm_list); + mutex_unlock(&pwm_lock); + + return 0; +} + +static int s3c_pwm_probe(struct platform_device *pdev) +{ + struct device *dev = &pdev->dev; + struct pwm_device *pwm; + unsigned long flags; + unsigned long tcon; + unsigned int id = pdev->id; + int ret; + + if (id == 4) { + dev_err(dev, "TIMER4 is currently not supported\n"); + return -ENXIO; + } + + pwm = kzalloc(sizeof(struct pwm_device), GFP_KERNEL); + if (pwm == NULL) { + dev_err(dev, "failed to allocate pwm_device\n"); + return -ENOMEM; + } + + pwm->pdev = pdev; + pwm->pwm_id = id; + + /* calculate base of control bits in TCON */ + pwm->tcon_base = id == 0 ? 0 : (id * 4) + 4; + + pwm->clk = clk_get(dev, "pwm-tin"); + if (IS_ERR(pwm->clk)) { + dev_err(dev, "failed to get pwm tin clk\n"); + ret = PTR_ERR(pwm->clk); + goto err_alloc; + } + + pwm->clk_div = clk_get(dev, "pwm-tdiv"); + if (IS_ERR(pwm->clk_div)) { + dev_err(dev, "failed to get pwm tdiv clk\n"); + ret = PTR_ERR(pwm->clk_div); + goto err_clk_tin; + } + + local_irq_save(flags); + + tcon = __raw_readl(S3C2410_TCON); + tcon |= pwm_tcon_invert(pwm); + __raw_writel(tcon, S3C2410_TCON); + + local_irq_restore(flags); + + + ret = pwm_register(pwm); + if (ret) { + dev_err(dev, "failed to register pwm\n"); + goto err_clk_tdiv; + } + + pwm_dbg(pwm, "config bits %02x\n", + (__raw_readl(S3C2410_TCON) >> pwm->tcon_base) & 0x0f); + + dev_info(dev, "tin at %lu, tdiv at %lu, tin=%sclk, base %d\n", + clk_get_rate(pwm->clk), + clk_get_rate(pwm->clk_div), + pwm_is_tdiv(pwm) ? "div" : "ext", pwm->tcon_base); + + platform_set_drvdata(pdev, pwm); + return 0; + + err_clk_tdiv: + clk_put(pwm->clk_div); + + err_clk_tin: + clk_put(pwm->clk); + + err_alloc: + kfree(pwm); + return ret; +} + +static int s3c_pwm_remove(struct platform_device *pdev) +{ + struct pwm_device *pwm = platform_get_drvdata(pdev); + + clk_put(pwm->clk_div); + clk_put(pwm->clk); + kfree(pwm); + + return 0; +} + +static struct platform_driver s3c_pwm_driver = { + .driver = { + .name = "s3c24xx-pwm", + .owner = THIS_MODULE, + }, + .probe = s3c_pwm_probe, + .remove = __devexit_p(s3c_pwm_remove), +}; + +static int __init pwm_init(void) +{ + int ret; + + clk_scaler[0] = clk_get(NULL, "pwm-scaler0"); + clk_scaler[1] = clk_get(NULL, "pwm-scaler1"); + + if (IS_ERR(clk_scaler[0]) || IS_ERR(clk_scaler[1])) { + printk(KERN_ERR "%s: failed to get scaler clocks\n", __func__); + return -EINVAL; + } + + ret = platform_driver_register(&s3c_pwm_driver); + if (ret) + printk(KERN_ERR "%s: failed to add pwm driver\n", __func__); + + return ret; +} + +arch_initcall(pwm_init); diff --git a/arch/arm/tools/mach-types b/arch/arm/tools/mach-types index 207a8b5a0c4..0be5630ff56 100644 --- a/arch/arm/tools/mach-types +++ b/arch/arm/tools/mach-types @@ -12,7 +12,7 @@ # # http://www.arm.linux.org.uk/developer/machines/?action=new # -# Last update: Sat Apr 19 11:23:38 2008 +# Last update: Mon Jul 7 16:25:39 2008 # # machine_is_xxx CONFIG_xxxx MACH_TYPE_xxx number # @@ -560,7 +560,6 @@ husky MACH_HUSKY HUSKY 543 boxer MACH_BOXER BOXER 544 shepherd MACH_SHEPHERD SHEPHERD 545 aml42800aa MACH_AML42800AA AML42800AA 546 -ml674001 MACH_MACH_TYPE_ML674001 MACH_TYPE_ML674001 547 lpc2294 MACH_LPC2294 LPC2294 548 switchgrass MACH_SWITCHGRASS SWITCHGRASS 549 ens_cmu MACH_ENS_CMU ENS_CMU 550 @@ -748,7 +747,6 @@ anubis MACH_ANUBIS ANUBIS 734 ite8152 MACH_ITE8152 ITE8152 735 lpc3xxx MACH_LPC3XXX LPC3XXX 736 puppeteer MACH_PUPPETEER PUPPETEER 737 -vt001 MACH_MACH_VADATECH MACH_VADATECH 738 e570 MACH_E570 E570 739 x50 MACH_X50 X50 740 recon MACH_RECON RECON 741 @@ -839,7 +837,7 @@ ccxp270 MACH_CCXP CCXP 825 omap_gsample MACH_OMAP_GSAMPLE OMAP_GSAMPLE 826 realview_eb MACH_REALVIEW_EB REALVIEW_EB 827 samoa MACH_SAMOA SAMOA 828 -t3xscale MACH_T3XSCALE T3XSCALE 829 +palmt3 MACH_PALMT3 PALMT3 829 i878 MACH_I878 I878 830 borzoi MACH_BORZOI BORZOI 831 gecko MACH_GECKO GECKO 832 @@ -895,7 +893,7 @@ mio8390 MACH_MIO8390 MIO8390 881 omi_board MACH_OMI_BOARD OMI_BOARD 882 mx21civ MACH_MX21CIV MX21CIV 883 mahi_cdac MACH_MAHI_CDAC MAHI_CDAC 884 -xscale_palmtx MACH_XSCALE_PALMTX XSCALE_PALMTX 885 +palmtx MACH_PALMTX PALMTX 885 s3c2413 MACH_S3C2413 S3C2413 887 samsys_ep0 MACH_SAMSYS_EP0 SAMSYS_EP0 888 wg302v1 MACH_WG302V1 WG302V1 889 @@ -918,7 +916,7 @@ nxdb500 MACH_NXDB500 NXDB500 905 apf9328 MACH_APF9328 APF9328 906 omap_wipoq MACH_OMAP_WIPOQ OMAP_WIPOQ 907 omap_twip MACH_OMAP_TWIP OMAP_TWIP 908 -xscale_treo650 MACH_XSCALE_PALMTREO650 XSCALE_PALMTREO650 909 +palmtreo650 MACH_PALMTREO650 PALMTREO650 909 acumen MACH_ACUMEN ACUMEN 910 xp100 MACH_XP100 XP100 911 fs2410 MACH_FS2410 FS2410 912 @@ -926,8 +924,8 @@ pxa270_cerf MACH_PXA270_CERF PXA270_CERF 913 sq2ftlpalm MACH_SQ2FTLPALM SQ2FTLPALM 914 bsemserver MACH_BSEMSERVER BSEMSERVER 915 netclient MACH_NETCLIENT NETCLIENT 916 -xscale_palmtt5 MACH_XSCALE_PALMTT5 XSCALE_PALMTT5 917 -xscale_palmtc MACH_OMAP_PALMTC OMAP_PALMTC 918 +palmt5 MACH_PALMT5 PALMT5 917 +palmtc MACH_PALMTC PALMTC 918 omap_apollon MACH_OMAP_APOLLON OMAP_APOLLON 919 mxc30030evb MACH_MXC30030EVB MXC30030EVB 920 rea_2d MACH_REA_2D REA_2D 921 @@ -1220,7 +1218,6 @@ empca400 MACH_EMPCA400 EMPCA400 1211 em7210 MACH_EM7210 EM7210 1212 htchermes MACH_HTCHERMES HTCHERMES 1213 eti_c1 MACH_ETI_C1 ETI_C1 1214 -mach_dep2410 MACH_MACH_DEP2410 MACH_DEP2410 1215 ac100 MACH_AC100 AC100 1216 sneetch MACH_SNEETCH SNEETCH 1217 studentmate MACH_STUDENTMATE STUDENTMATE 1218 @@ -1421,10 +1418,10 @@ looxc550 MACH_LOOXC550 LOOXC550 1417 cnty_titan MACH_CNTY_TITAN CNTY_TITAN 1418 app3xx MACH_APP3XX APP3XX 1419 sideoatsgrama MACH_SIDEOATSGRAMA SIDEOATSGRAMA 1420 -xscale_palmt700p MACH_XSCALE_PALMT700P XSCALE_PALMT700P 1421 -xscale_palmt700w MACH_XSCALE_PALMT700W XSCALE_PALMT700W 1422 -xscale_palmt750 MACH_XSCALE_PALMT750 XSCALE_PALMT750 1423 -xscale_palmt755p MACH_XSCALE_PALMT755P XSCALE_PALMT755P 1424 +palmtreo700p MACH_PALMTREO700P PALMTREO700P 1421 +palmtreo700w MACH_PALMTREO700W PALMTREO700W 1422 +palmtreo750 MACH_PALMTREO750 PALMTREO750 1423 +palmtreo755p MACH_PALMTREO755P PALMTREO755P 1424 ezreganut9200 MACH_EZREGANUT9200 EZREGANUT9200 1425 sarge MACH_SARGE SARGE 1426 a696 MACH_A696 A696 1427 @@ -1463,7 +1460,7 @@ artemis MACH_ARTEMIS ARTEMIS 1462 htctitan MACH_HTCTITAN HTCTITAN 1463 qranium MACH_QRANIUM QRANIUM 1464 adx_wsc2 MACH_ADX_WSC2 ADX_WSC2 1465 -adx_medcom MACH_ADX_MEDINET ADX_MEDINET 1466 +adx_medcom MACH_ADX_MEDCOM ADX_MEDCOM 1466 bboard MACH_BBOARD BBOARD 1467 cambria MACH_CAMBRIA CAMBRIA 1468 mt7xxx MACH_MT7XXX MT7XXX 1469 @@ -1519,7 +1516,7 @@ wp188 MACH_WP188 WP188 1518 corsica MACH_CORSICA CORSICA 1519 bigeye MACH_BIGEYE BIGEYE 1520 tll5000 MACH_TLL5000 TLL5000 1522 -hni270 MACH_HNI_X270 HNI_X270 1523 +bebot MACH_BEBOT BEBOT 1523 qong MACH_QONG QONG 1524 tcompact MACH_TCOMPACT TCOMPACT 1525 puma5 MACH_PUMA5 PUMA5 1526 @@ -1636,7 +1633,6 @@ awlug4lcu MACH_AWLUG4LCU AWLUG4LCU 1637 palermoc MACH_PALERMOC PALERMOC 1638 omap_ldp MACH_OMAP_LDP OMAP_LDP 1639 ip500 MACH_IP500 IP500 1640 -mx35ads MACH_MACH_MX35ADS MACH_MX35ADS 1641 ase2 MACH_ASE2 ASE2 1642 mx35evb MACH_MX35EVB MX35EVB 1643 aml_m8050 MACH_AML_M8050 AML_M8050 1644 @@ -1647,7 +1643,7 @@ badger MACH_BADGER BADGER 1648 trizeps4wl MACH_TRIZEPS4WL TRIZEPS4WL 1649 trizeps5 MACH_TRIZEPS5 TRIZEPS5 1650 marlin MACH_MARLIN MARLIN 1651 -ts7800 MACH_TS7800 TS7800 1652 +ts78xx MACH_TS78XX TS78XX 1652 hpipaq214 MACH_HPIPAQ214 HPIPAQ214 1653 at572d940dcm MACH_AT572D940DCM AT572D940DCM 1654 ne1board MACH_NE1BOARD NE1BOARD 1655 @@ -1720,3 +1716,99 @@ htc_kaiser MACH_HTC_KAISER HTC_KAISER 1724 lg_ks20 MACH_LG_KS20 LG_KS20 1725 hhgps MACH_HHGPS HHGPS 1726 nokia_n810_wimax MACH_NOKIA_N810_WIMAX NOKIA_N810_WIMAX 1727 +insight MACH_INSIGHT INSIGHT 1728 +sapphire MACH_SAPPHIRE SAPPHIRE 1729 +csb637xo MACH_CSB637XO CSB637XO 1730 +evisiong MACH_EVISIONG EVISIONG 1731 +stmp37xx MACH_STMP37XX STMP37XX 1732 +stmp378x MACH_STMP38XX STMP38XX 1733 +tnt MACH_TNT TNT 1734 +tbxt MACH_TBXT TBXT 1735 +playmate MACH_PLAYMATE PLAYMATE 1736 +pns10 MACH_PNS10 PNS10 1737 +eznavi MACH_EZNAVI EZNAVI 1738 +ps4000 MACH_PS4000 PS4000 1739 +ezx_a780 MACH_EZX_A780 EZX_A780 1740 +ezx_e680 MACH_EZX_E680 EZX_E680 1741 +ezx_a1200 MACH_EZX_A1200 EZX_A1200 1742 +ezx_e6 MACH_EZX_E6 EZX_E6 1743 +ezx_e2 MACH_EZX_E2 EZX_E2 1744 +ezx_a910 MACH_EZX_A910 EZX_A910 1745 +cwmx31 MACH_CWMX31 CWMX31 1746 +sl2312 MACH_SL2312 SL2312 1747 +blenny MACH_BLENNY BLENNY 1748 +ds107 MACH_DS107 DS107 1749 +dsx07 MACH_DSX07 DSX07 1750 +picocom1 MACH_PICOCOM1 PICOCOM1 1751 +lynx_wolverine MACH_LYNX_WOLVERINE LYNX_WOLVERINE 1752 +ubisys_p9_sc19 MACH_UBISYS_P9_SC19 UBISYS_P9_SC19 1753 +kratos_low MACH_KRATOS_LOW KRATOS_LOW 1754 +m700 MACH_M700 M700 1755 +edmini_v2 MACH_EDMINI_V2 EDMINI_V2 1756 +zipit2 MACH_ZIPIT2 ZIPIT2 1757 +hslfemtocell MACH_HSLFEMTOCELL HSLFEMTOCELL 1758 +daintree_at91 MACH_DAINTREE_AT91 DAINTREE_AT91 1759 +sg560usb MACH_SG560USB SG560USB 1760 +omap3_pandora MACH_OMAP3_PANDORA OMAP3_PANDORA 1761 +usr8200 MACH_USR8200 USR8200 1762 +s1s65k MACH_S1S65K S1S65K 1763 +s2s65a MACH_S2S65A S2S65A 1764 +icore MACH_ICORE ICORE 1765 +mss2 MACH_MSS2 MSS2 1766 +belmont MACH_BELMONT BELMONT 1767 +asusp525 MACH_ASUSP525 ASUSP525 1768 +lb88rc8480 MACH_LB88RC8480 LB88RC8480 1769 +hipxa MACH_HIPXA HIPXA 1770 +mx25_3ds MACH_MX25_3DS MX25_3DS 1771 +m800 MACH_M800 M800 1772 +omap3530_lv_som MACH_OMAP3530_LV_SOM OMAP3530_LV_SOM 1773 +prima_evb MACH_PRIMA_EVB PRIMA_EVB 1774 +mx31bt1 MACH_MX31BT1 MX31BT1 1775 +atlas4_evb MACH_ATLAS4_EVB ATLAS4_EVB 1776 +mx31cicada MACH_MX31CICADA MX31CICADA 1777 +mi424wr MACH_MI424WR MI424WR 1778 +axs_ultrax MACH_AXS_ULTRAX AXS_ULTRAX 1779 +at572d940deb MACH_AT572D940DEB AT572D940DEB 1780 +davinci_da8xx_evm MACH_DAVINCI_DA8XX_EVM DAVINCI_DA8XX_EVM 1781 +ep9302 MACH_EP9302 EP9302 1782 +at572d940hfeb MACH_AT572D940HFEB AT572D940HFEB 1783 +cybook3 MACH_CYBOOK3 CYBOOK3 1784 +wdg002 MACH_WDG002 WDG002 1785 +sg560adsl MACH_SG560ADSL SG560ADSL 1786 +nextio_n2800_ica MACH_NEXTIO_N2800_ICA NEXTIO_N2800_ICA 1787 +marvell_newdb MACH_MARVELL_NEWDB MARVELL_NEWDB 1789 +vandihud MACH_VANDIHUD VANDIHUD 1790 +magx_e8 MACH_MAGX_E8 MAGX_E8 1791 +magx_z6 MACH_MAGX_Z6 MAGX_Z6 1792 +magx_v8 MACH_MAGX_V8 MAGX_V8 1793 +magx_u9 MACH_MAGX_U9 MAGX_U9 1794 +toughcf08 MACH_TOUGHCF08 TOUGHCF08 1795 +zw4400 MACH_ZW4400 ZW4400 1796 +marat91 MACH_MARAT91 MARAT91 1797 +overo MACH_OVERO OVERO 1798 +at2440evb MACH_AT2440EVB AT2440EVB 1799 +neocore926 MACH_NEOCORE926 NEOCORE926 1800 +wnr854t MACH_WNR854T WNR854T 1801 +imx27 MACH_IMX27 IMX27 1802 +moose_db MACH_MOOSE_DB MOOSE_DB 1803 +fab4 MACH_FAB4 FAB4 1804 +htcdiamond MACH_HTCDIAMOND HTCDIAMOND 1805 +fiona MACH_FIONA FIONA 1806 +mxc30030_x MACH_MXC30030_X MXC30030_X 1807 +bmp1000 MACH_BMP1000 BMP1000 1808 +logi9200 MACH_LOGI9200 LOGI9200 1809 +tqma31 MACH_TQMA31 TQMA31 1810 +ccw9p9215js MACH_CCW9P9215JS CCW9P9215JS 1811 +rd88f5181l_ge MACH_RD88F5181L_GE RD88F5181L_GE 1812 +sifmain MACH_SIFMAIN SIFMAIN 1813 +sam9_l9261 MACH_SAM9_L9261 SAM9_L9261 1814 +cc9m2443js MACH_CC9M2443JS CC9M2443JS 1815 +xaria300 MACH_XARIA300 XARIA300 1816 +it9200 MACH_IT9200 IT9200 1817 +rd88f5181l_fxo MACH_RD88F5181L_FXO RD88F5181L_FXO 1818 +kriss_sensor MACH_KRISS_SENSOR KRISS_SENSOR 1819 +pilz_pmi5 MACH_PILZ_PMI5 PILZ_PMI5 1820 +jade MACH_JADE JADE 1821 +ks8695_softplc MACH_KS8695_SOFTPLC KS8695_SOFTPLC 1822 +gprisc4 MACH_GPRISC4 GPRISC4 1823 +stamp9260 MACH_STAMP9260 STAMP9260 1824 diff --git a/arch/sh/configs/landisk_defconfig b/arch/sh/configs/landisk_defconfig index f52db125432..38f934ab50c 100644 --- a/arch/sh/configs/landisk_defconfig +++ b/arch/sh/configs/landisk_defconfig @@ -226,7 +226,6 @@ CONFIG_CPU_HAS_PTEA=y # CONFIG_SH_TMU=y CONFIG_SH_TIMER_IRQ=16 -# CONFIG_NO_IDLE_HZ is not set CONFIG_SH_PCLK_FREQ=33333333 # diff --git a/arch/sh/configs/lboxre2_defconfig b/arch/sh/configs/lboxre2_defconfig index 9fa66d92a4e..b68b6cdbb78 100644 --- a/arch/sh/configs/lboxre2_defconfig +++ b/arch/sh/configs/lboxre2_defconfig @@ -231,7 +231,6 @@ CONFIG_CPU_HAS_PTEA=y # CONFIG_SH_TMU=y CONFIG_SH_TIMER_IRQ=16 -# CONFIG_NO_IDLE_HZ is not set CONFIG_SH_PCLK_FREQ=40000000 # diff --git a/arch/sh/configs/se7705_defconfig b/arch/sh/configs/se7705_defconfig index 84717d85486..490dcbc2ce3 100644 --- a/arch/sh/configs/se7705_defconfig +++ b/arch/sh/configs/se7705_defconfig @@ -239,7 +239,6 @@ CONFIG_CPU_HAS_SR_RB=y # CONFIG_SH_TMU=y CONFIG_SH_TIMER_IRQ=16 -# CONFIG_NO_IDLE_HZ is not set CONFIG_SH_PCLK_FREQ=33333333 # diff --git a/arch/sh/configs/se7712_defconfig b/arch/sh/configs/se7712_defconfig index 240a1cef69a..2dd83af988f 100644 --- a/arch/sh/configs/se7712_defconfig +++ b/arch/sh/configs/se7712_defconfig @@ -236,7 +236,6 @@ CONFIG_CPU_HAS_SR_RB=y # CONFIG_SH_TMU=y CONFIG_SH_TIMER_IRQ=16 -# CONFIG_NO_IDLE_HZ is not set CONFIG_SH_PCLK_FREQ=66666666 # diff --git a/arch/sh/configs/se7750_defconfig b/arch/sh/configs/se7750_defconfig index c60b6fd4fc4..167786f9a9b 100644 --- a/arch/sh/configs/se7750_defconfig +++ b/arch/sh/configs/se7750_defconfig @@ -235,7 +235,6 @@ CONFIG_CPU_HAS_PTEA=y # CONFIG_SH_TMU=y CONFIG_SH_TIMER_IRQ=16 -# CONFIG_NO_IDLE_HZ is not set CONFIG_SH_PCLK_FREQ=33333333 # diff --git a/drivers/acorn/char/Makefile b/drivers/acorn/char/Makefile deleted file mode 100644 index d006c9f168d..00000000000 --- a/drivers/acorn/char/Makefile +++ /dev/null @@ -1,5 +0,0 @@ -# -# Makefile for the acorn character device drivers. -# - -obj-$(CONFIG_L7200_KEYB) += defkeymap-l7200.o keyb_l7200.o diff --git a/drivers/acorn/char/defkeymap-l7200.c b/drivers/acorn/char/defkeymap-l7200.c deleted file mode 100644 index 93d80a1c36f..00000000000 --- a/drivers/acorn/char/defkeymap-l7200.c +++ /dev/null @@ -1,386 +0,0 @@ -/* - * linux/drivers/acorn/char/defkeymap-l7200.c - * - * Default keyboard maps for LinkUp Systems L7200 board - * - * Copyright (C) 2000 Steve Hill (sjhill@cotw.com) - * - * Changelog: - * 08-04-2000 SJH Created file - */ - -#include <linux/types.h> -#include <linux/keyboard.h> -#include <linux/kd.h> - -/* Normal (maps 1:1 with no processing) */ -#define KTn 0xF0 -/* Function keys */ -#define KTf 0xF1 -/* Special (Performs special house-keeping funcs) */ -#define KTs 0xF2 -#define KIGNORE K(KTs, 0) /* Ignore */ -#define KENTER K(KTs, 1) /* Enter */ -#define KREGS K(KTs, 2) /* Regs */ -#define KMEM K(KTs, 3) /* Mem */ -#define KSTAT K(KTs, 4) /* State */ -#define KINTR K(KTs, 5) /* Intr */ -#define Ksl 6 /* Last console */ -#define KCAPSLK K(KTs, 7) /* Caps lock */ -#define KNUMLK K(KTs, 8) /* Num-lock */ -#define KSCRLLK K(KTs, 9) /* Scroll-lock */ -#define KSCRLFOR K(KTs,10) /* Scroll forward */ -#define KSCRLBAK K(KTs,11) /* Scroll back */ -#define KREBOOT K(KTs,12) /* Reboot */ -#define KCAPSON K(KTs,13) /* Caps on */ -#define KCOMPOSE K(KTs,14) /* Compose */ -#define KSAK K(KTs,15) /* SAK */ -#define CONS_DEC K(KTs,16) /* Dec console */ -#define CONS_INC K(KTs,17) /* Incr console */ -#define KFLOPPY K(KTs,18) /* Floppy */ -/* Key pad (0-9 = digits, 10=+, 11=-, 12=*, 13=/, 14=enter, 16=., 17=# */ -#define KTp 0xF3 -#define KPAD_0 K(KTp, 0 ) -#define KPAD_1 K(KTp, 1 ) -#define KPAD_2 K(KTp, 2 ) -#define KPAD_3 K(KTp, 3 ) -#define KPAD_4 K(KTp, 4 ) -#define KPAD_5 K(KTp, 5 ) -#define KPAD_6 K(KTp, 6 ) -#define KPAD_7 K(KTp, 7 ) -#define KPAD_8 K(KTp, 8 ) -#define KPAD_9 K(KTp, 9 ) -#define KPAD_PL K(KTp,10 ) -#define KPAD_MI K(KTp,11 ) -#define KPAD_ML K(KTp,12 ) -#define KPAD_DV K(KTp,13 ) -#define KPAD_EN K(KTp,14 ) -#define KPAD_DT K(KTp,16 ) -#define KPAD_HS K(KTp,20 ) -/* Console switching */ -#define KCn 0xF5 -/* Cursor */ -#define KTc 0xF6 -#define Kcd 0 /* Cursor down */ -#define Kcl 1 /* Cursor left */ -#define Kcr 2 /* Cursor right */ -#define Kcu 3 /* Cursor up */ -/* Shift/alt modifiers etc */ -#define KMd 0xF7 -#define KSHIFT K(KMd, 0 ) -#define KALTGR K(KMd, 1 ) -#define KCTRL K(KMd, 2 ) -#define KALT K(KMd, 3 ) -/* Meta */ -#define KMt 0xF8 -#define KAs 0xF9 -#define KPADA_0 K(KAs, 0 ) -#define KPADA_1 K(KAs, 1 ) -#define KPADA_2 K(KAs, 2 ) -#define KPADA_3 K(KAs, 3 ) -#define KPADA_4 K(KAs, 4 ) -#define KPADA_5 K(KAs, 5 ) -#define KPADA_6 K(KAs, 6 ) -#define KPADA_7 K(KAs, 7 ) -#define KPADA_8 K(KAs, 8 ) -#define KPADA_9 K(KAs, 9 ) -#define KPADB_0 K(KAs,10 ) -#define KPADB_1 K(KAs,11 ) -#define KPADB_2 K(KAs,12 ) -#define KPADB_3 K(KAs,13 ) -#define KPADB_4 K(KAs,14 ) -#define KPADB_5 K(KAs,15 ) -#define KPADB_6 K(KAs,16 ) -#define KPADB_7 K(KAs,17 ) -#define KPADB_8 K(KAs,18 ) -#define KPADB_9 K(KAs,19 ) -/* Locking keys */ -#define KLk 0xFA -/* Letters */ -#define KTl 0xFB - -/* - * Here is the layout of the keys for the Fujitsu QWERTY - * style keyboard: - * - * static char Fujitsu_Key_Table[] = - * { - * KALT, '`' , KNUL, KCTL, KFUN, KESC, '1' , '2' , - * '9' , '0' , '-' , '=' , KNUL, KBSP, KNUL, KNUL, - * KNUL, KBSL, KSHF, KNUL, KNUL, KDEL, KNUL, 't' , - * 'y' , 'u' , 'i' , KRET, KSHF, KPGD, KNUL, KNUL, - * KNUL, KTAB, KNUL, KNUL, KNUL, 'q' , 'w' , 'e' , - * 'r' , 'o' , 'p' , '[' , KNUL, ']' , KNUL, KNUL, - * KNUL, 'z' , KNUL, KNUL, KNUL, KSHL, KNUL, KNUL, - * 'k' , 'l' , ';' , KSQT, KNUL, KPGU, KNUL, KNUL, - * KNUL, 'a' , KNUL, KNUL, KNUL, 's' , 'd' , 'f' , - * 'g' , 'h' , 'j' , '/' , KNUL, KHME, KNUL, KNUL, - * KNUL, 'x' , KNUL, KNUL, KNUL, 'c' , 'v' , 'b' , - * 'n' , 'm' , ',' , '.' , KNUL, ' ' , KNUL, KNUL, - * KNUL, KNUL, KNUL, KNUL, KNUL, '3' , '4' , '5' , - * '6' , '7' , '8' , KNUL, KPRG, KNUL, KEND, KNUL, - * }; - */ - -u_short plain_map[NR_KEYS]= -{ - 0xf703, 0xf060, 0xf200, 0xf702, 0xf200, 0xf01b, 0xf031, 0xf032, - 0xf039, 0xf030, 0xf02d, 0xf03d, 0xf200, 0xf07f, 0xf200, 0xf200, - 0xf200, 0xf05c, 0xf700, 0xf200, 0xf200, 0xf116, 0xf000, 0xfb74, - 0xfb79, 0xfb75, 0xfb69, 0xf201, 0xf700, 0xf600, 0xf200, 0xf200, - 0xf200, 0xf009, 0xf200, 0xf200, 0xf200, 0xfb71, 0xfb77, 0xfb65, - 0xfb72, 0xfb6f, 0xfb70, 0xf05b, 0xf200, 0xf05d, 0xf200, 0xf200, - 0xf200, 0xfb7a, 0xf200, 0xf200, 0xf200, 0xf207, 0xf200, 0xf200, - 0xfb6b, 0xfb6c, 0xf03b, 0xf027, 0xf200, 0xf603, 0xf200, 0xf200, - 0xf200, 0xfb61, 0xf200, 0xf200, 0xf200, 0xfb73, 0xfb64, 0xfb66, - 0xfb67, 0xfb68, 0xfb6a, 0xf02f, 0xf200, 0xf601, 0xf200, 0xf200, - 0xf200, 0xfb78, 0xf200, 0xf200, 0xf200, 0xfb63, 0xfb76, 0xfb62, - 0xfb6e, 0xfb6d, 0xf02c, 0xf02e, 0xf200, 0xf020, 0xf200, 0xf200, - 0xf200, 0xf200, 0xf200, 0xf200, 0xf200, 0xf033, 0xf034, 0xf035, - 0xf036, 0xf037, 0xf038, 0xf200, 0xf200, 0xf200, 0xf602, 0xf200, - 0xf200, 0xf200, 0xf200, 0xf200, 0xf200, 0xf200, 0xf200, 0xf200, - 0xf200, 0xf200, 0xf200, 0xf200, 0xf200, 0xf200, 0xf200, 0xf200, -}; - -u_short shift_map[NR_KEYS]= -{ - 0xf703, 0xf07e, 0xf200, 0xf702, 0xf200, 0xf01b, 0xf021, 0xf040, - 0xf028, 0xf029, 0xf05f, 0xf02b, 0xf200, 0xf07f, 0xf200, 0xf200, - 0xf200, 0xf07c, 0xf700, 0xf200, 0xf200, 0xf116, 0xf000, 0xfb54, - 0xfb59, 0xfb55, 0xfb49, 0xf201, 0xf700, 0xf600, 0xf200, 0xf200, - 0xf200, 0xf009, 0xf200, 0xf200, 0xf200, 0xfb51, 0xfb57, 0xfb45, - 0xfb52, 0xfb4f, 0xfb50, 0xf07b, 0xf200, 0xf07d, 0xf200, 0xf200, - 0xf200, 0xfb5a, 0xf200, 0xf200, 0xf200, 0xf207, 0xf200, 0xf200, - 0xfb4b, 0xfb4c, 0xf03a, 0xf022, 0xf200, 0xf603, 0xf200, 0xf200, - 0xf200, 0xfb41, 0xf200, 0xf200, 0xf200, 0xfb53, 0xfb44, 0xfb46, - 0xfb47, 0xfb48, 0xfb4a, 0xf03f, 0xf200, 0xf601, 0xf200, 0xf200, - 0xf200, 0xfb58, 0xf200, 0xf200, 0xf200, 0xfb43, 0xfb56, 0xfb42, - 0xfb4e, 0xfb4d, 0xf03c, 0xf03e, 0xf200, 0xf020, 0xf200, 0xf200, - 0xf200, 0xf200, 0xf200, 0xf200, 0xf200, 0xf023, 0xf024, 0xf025, - 0xf05e, 0xf026, 0xf02a, 0xf200, 0xf200, 0xf200, 0xf602, 0xf200, - 0xf200, 0xf200, 0xf200, 0xf200, 0xf200, 0xf200, 0xf200, 0xf200, - 0xf200, 0xf200, 0xf200, 0xf200, 0xf200, 0xf200, 0xf200, 0xf200, -}; - -u_short altgr_map[NR_KEYS]= -{ - KIGNORE ,K(KCn,12 ),K(KCn,13 ),K(KCn,14 ),K(KCn,15 ),K(KCn,16 ),K(KCn,17 ),K(KCn, 18), - K(KCn, 19),K(KCn,20 ),K(KCn,21 ),K(KCn,22 ),K(KCn,23 ),KIGNORE ,KREGS ,KINTR , - KIGNORE ,KIGNORE ,K(KTn,'@'),KIGNORE ,K(KTn,'$'),KIGNORE ,KIGNORE ,K(KTn,'{'), - K(KTn,'['),K(KTn,']'),K(KTn,'}'),K(KTn,'\\'),KIGNORE ,KIGNORE ,KIGNORE ,K(KTf,21 ), - K(KTf,20 ),K(KTf,24 ),KNUMLK ,KPAD_DV ,KPAD_ML ,KPAD_HS ,KIGNORE ,K(KTl,'q'), - K(KTl,'w'),K(KTl,'e'),K(KTl,'r'),K(KTl,'t' ),K(KTl,'y'),K(KTl,'u'),K(KTl,'i' ),K(KTl,'o'), - K(KTl,'p'),KIGNORE ,K(KTn,'~'),KIGNORE ,K(KTf,22 ),K(KTf,23 ),K(KTf,25 ),KPADB_7 , - KPADB_8 ,KPADB_9 ,KPAD_MI ,KCTRL ,K(KAs,20 ),K(KTl,'s'),K(KAs,23 ),K(KAs,25 ), - K(KTl,'g'),K(KTl,'h'),K(KTl,'j'),K(KTl,'k' ),K(KTl,'l'),KIGNORE ,KIGNORE ,KENTER , - KPADB_4 ,KPADB_5 ,KPADB_6 ,KPAD_PL ,KSHIFT ,KIGNORE ,K(KTl,'z' ),K(KTl,'x'), - K(KAs,22 ),K(KTl,'v'),K(KTl,21 ),K(KTl,'n' ),K(KTl,'m'),KIGNORE ,KIGNORE ,KIGNORE , - KSHIFT ,K(KTc,Kcu),KPADB_1 ,KPADB_2 ,KPADB_3 ,KCAPSLK ,KALT ,KIGNORE , - KALTGR ,KCTRL ,K(KTc,Kcl),K(KTc,Kcd ),K(KTc,Kcr),KPADB_0 ,KPAD_DT ,KPAD_EN , - KIGNORE ,KIGNORE ,KIGNORE ,KIGNORE ,KIGNORE ,KIGNORE ,KIGNORE ,KIGNORE , - KIGNORE ,KIGNORE ,KIGNORE ,KIGNORE ,KIGNORE ,KIGNORE ,KIGNORE ,KIGNORE , - KIGNORE ,KIGNORE ,KIGNORE ,KIGNORE ,KIGNORE ,KIGNORE ,KIGNORE ,KIGNORE , -}; - -u_short ctrl_map[NR_KEYS]= -{ - 0xf703, 0xf200, 0xf200, 0xf702, 0xf200, 0xf200, 0xf001, 0xf002, - 0xf009, 0xf000, 0xf031, 0xf200, 0xf200, 0xf07f, 0xf200, 0xf200, - 0xf200, 0xf01c, 0xf700, 0xf200, 0xf200, 0xf116, 0xf000, 0xf020, - 0xf019, 0xf015, 0xf009, 0xf201, 0xf700, 0xf600, 0xf200, 0xf200, - 0xf200, 0xf009, 0xf200, 0xf200, 0xf200, 0xf011, 0xf017, 0xf005, - 0xf012, 0xf00f, 0xf010, 0xf01b, 0xf200, 0xf01d, 0xf200, 0xf200, - 0xf200, 0xf01a, 0xf200, 0xf200, 0xf200, 0xf207, 0xf200, 0xf200, - 0xf00b, 0xf00c, 0xf200, 0xf007, 0xf200, 0xf603, 0xf200, 0xf200, - 0xf200, 0xf001, 0xf200, 0xf200, 0xf200, 0xf001, 0xf013, 0xf006, - 0xf007, 0xf008, 0xf00a, 0xf07f, 0xf200, 0xf601, 0xf200, 0xf200, - 0xf200, 0xf018, 0xf200, 0xf200, 0xf200, 0xf003, 0xf016, 0xf002, - 0xf00e, 0xf00d, 0xf200, 0xf200, 0xf200, 0xf000, 0xf200, 0xf200, - 0xf200, 0xf200, 0xf200, 0xf200, 0xf200, 0xf01b, 0xf01c, 0xf01d, - 0xf036, 0xf037, 0xf038, 0xf200, 0xf200, 0xf200, 0xf602, 0xf200, - 0xf200, 0xf200, 0xf200, 0xf200, 0xf200, 0xf200, 0xf200, 0xf200, - 0xf200, 0xf200, 0xf200, 0xf200, 0xf200, 0xf200, 0xf602, 0xf200, -}; - -u_short shift_ctrl_map[NR_KEYS]= -{ - KIGNORE ,KIGNORE ,KIGNORE ,KIGNORE ,KIGNORE ,KIGNORE ,KIGNORE ,KIGNORE , - KIGNORE ,KIGNORE ,KIGNORE ,KIGNORE ,KIGNORE ,KIGNORE ,KFLOPPY ,KINTR , - KIGNORE ,KIGNORE ,K(KTn, 0 ),KIGNORE ,KIGNORE ,KIGNORE ,KIGNORE ,KIGNORE , - KIGNORE ,KIGNORE ,KIGNORE ,K(KTn,31 ),KIGNORE ,KIGNORE ,KIGNORE ,K(KTf,21 ), - K(KTf,20 ),K(KTf,24 ),KNUMLK ,KPAD_DV ,KPAD_ML ,KPAD_HS ,KIGNORE ,K(KTn,17 ), - K(KTn,23 ),K(KTn, 5 ),K(KTn,18 ),K(KTn,20 ),K(KTn,25 ),K(KTn,21 ),K(KTn, 9 ),K(KTn,15 ), - K(KTn,16 ),KIGNORE ,KIGNORE ,KIGNORE ,K(KTf,22 ),K(KTf,23 ),K(KTf,25 ),KPAD_7 , - KPAD_8 ,KPAD_9 ,KPAD_MI ,KCTRL ,K(KTn, 1 ),K(KTn,19 ),K(KTn, 4 ),K(KTn, 6 ), - K(KTn, 7 ),K(KTn, 8 ),K(KTn,10 ),K(KTn,11 ),K(KTn,12 ),KIGNORE ,K(KTn, 7 ),KENTER , - KPAD_4 ,KPAD_5 ,KPAD_6 ,KPAD_PL ,KSHIFT ,KIGNORE ,K(KTn,26 ),K(KTn,24 ), - K(KTn, 3 ),K(KTn,22 ),K(KTn, 2 ),K(KTn,14 ),K(KTn,13 ),KIGNORE ,KIGNORE ,KIGNORE , - KSHIFT ,K(KTc,Kcu),KPAD_1 ,KPAD_2 ,KPAD_3 ,KCAPSLK ,KALT ,K(KTn, 0 ), - KALTGR ,KCTRL ,K(KTc,Kcl),K(KTc,Kcd ),K(KTc,Kcr),KPAD_0 ,KPAD_DT ,KPAD_EN , - KIGNORE ,KIGNORE ,KIGNORE ,KIGNORE ,KIGNORE ,KIGNORE ,KIGNORE ,KIGNORE , - KIGNORE ,KIGNORE ,KIGNORE ,KIGNORE ,KIGNORE ,KIGNORE ,KIGNORE ,KIGNORE , - KIGNORE ,KIGNORE ,KIGNORE ,KIGNORE ,KIGNORE ,KIGNORE ,KIGNORE ,KIGNORE , -}; - -u_short alt_map[NR_KEYS]= -{ - K(KMt,27 ),K(KCn, 0 ),K(KCn, 1 ),K(KCn, 2 ),K(KCn, 3 ),K(KCn, 4 ),K(KCn, 5 ),K(KCn, 6 ), - K(KCn, 7 ),K(KCn, 8 ),K(KCn, 9 ),K(KCn,10 ),K(KCn,11 ),KIGNORE ,KSCRLLK ,KINTR , - K(KMt,'`'),K(KMt,'1'),K(KMt,'2'),K(KMt,'3' ),K(KMt,'4'),K(KMt,'5'),K(KMt,'6' ),K(KMt,'7'), - K(KMt,'8'),K(KMt,'9'),K(KMt,'0'),K(KMt,'-' ),K(KMt,'='),K(KMt,'£'),K(KMt,127 ),K(KTf,21 ), - K(KTf,20 ),K(KTf,24 ),KNUMLK ,KPAD_DV ,KPAD_ML ,KPAD_HS ,K(KMt, 9 ),K(KMt,'q'), - K(KMt,'w'),K(KMt,'e'),K(KMt,'r'),K(KMt,'t' ),K(KMt,'y'),K(KMt,'u'),K(KMt,'i' ),K(KMt,'o'), - K(KMt,'p'),K(KMt,'['),K(KMt,']'),K(KMt,'\\'),K(KTf,22 ),K(KTf,23 ),K(KTf,25 ),KPADA_7 , - KPADA_8 ,KPADA_9 ,KPAD_MI ,KCTRL ,K(KMt,'a'),K(KMt,'s'),K(KMt,'d' ),K(KMt,'f'), - K(KMt,'g'),K(KMt,'h'),K(KMt,'j'),K(KMt,'k' ),K(KMt,'l'),K(KMt,';'),K(KMt,'\''),K(KMt,13 ), - KPADA_4 ,KPADA_5 ,KPADA_6 ,KPAD_PL ,KSHIFT ,KIGNORE ,K(KMt,'z' ),K(KMt,'x'), - K(KMt,'c'),K(KMt,'v'),K(KMt,'b'),K(KMt,'n' ),K(KMt,'m'),K(KMt,','),K(KMt,'.' ),KIGNORE , - KSHIFT ,K(KTc,Kcu),KPADA_1 ,KPADA_2 ,KPADA_3 ,KCAPSLK ,KALT ,K(KMt,' '), - KALTGR ,KCTRL ,CONS_DEC ,K(KTc,Kcd ),CONS_INC ,KPADA_0 ,KPAD_DT ,KPAD_EN , - KIGNORE ,KIGNORE ,KIGNORE ,KIGNORE ,KIGNORE ,KIGNORE ,KIGNORE ,KIGNORE , - KIGNORE ,KIGNORE ,KIGNORE ,KIGNORE ,KIGNORE ,KIGNORE ,KIGNORE ,KIGNORE , - KIGNORE ,KIGNORE ,KIGNORE ,KIGNORE ,KIGNORE ,KIGNORE ,KIGNORE ,KIGNORE , -}; - -u_short ctrl_alt_map[NR_KEYS]= -{ - KIGNORE ,K(KCn, 0 ),K(KCn, 1 ),K(KCn, 2 ),K(KCn, 3 ),K(KCn, 4 ),K(KCn, 5 ),K(KCn, 6 ), - K(KCn, 7 ),K(KCn, 8 ),K(KCn, 9 ),K(KCn,10 ),K(KCn,11 ),KIGNORE ,KIGNORE ,KINTR , - KIGNORE ,KIGNORE ,KIGNORE ,KIGNORE ,KIGNORE ,KIGNORE ,KIGNORE ,KIGNORE , - KIGNORE ,KIGNORE ,KIGNORE ,KIGNORE ,KIGNORE ,KIGNORE ,KIGNORE ,K(KTf,21 ), - K(KTf,20 ),K(KTf,24 ),KNUMLK ,KPAD_DV ,KPAD_ML ,KPAD_HS ,KIGNORE ,K(KMt,17 ), - K(KMt,23 ),K(KMt, 5 ),K(KMt,18 ),K(KMt,20 ),K(KMt,25 ),K(KMt,21 ),K(KMt, 9 ),K(KMt,15 ), - K(KMt,16 ),KIGNORE ,KIGNORE ,KIGNORE ,KREBOOT ,K(KTf,23 ),K(KTf,25 ),KPAD_7 , - KPAD_8 ,KPAD_9 ,KPAD_MI ,KCTRL ,K(KMt, 1 ),K(KMt,19 ),K(KMt, 4 ),K(KMt, 6 ), - K(KMt, 7 ),K(KMt, 8 ),K(KMt,10 ),K(KMt,11 ),K(KMt,12 ),KIGNORE ,KIGNORE ,KENTER , - KPAD_4 ,KPAD_5 ,KPAD_6 ,KPAD_PL ,KSHIFT ,KIGNORE ,K(KMt,26 ),K(KMt,24 ), - K(KMt, 3 ),K(KMt,22 ),K(KMt, 2 ),K(KMt,14 ),K(KMt,13 ),KIGNORE ,KIGNORE ,KIGNORE , - KSHIFT ,K(KTc,Kcu),KPAD_1 ,KPAD_2 ,KPAD_3 ,KCAPSLK ,KALT ,KIGNORE , - KALTGR ,KCTRL ,K(KTc,Kcl),K(KTc,Kcd ),K(KTc,Kcr),KPAD_0 ,KREBOOT ,KPAD_EN , - KIGNORE ,KIGNORE ,KIGNORE ,KIGNORE ,KIGNORE ,KIGNORE ,KIGNORE ,KIGNORE , - KIGNORE ,KIGNORE ,KIGNORE ,KIGNORE ,KIGNORE ,KIGNORE ,KIGNORE ,KIGNORE , - KIGNORE ,KIGNORE ,KIGNORE ,KIGNORE ,KIGNORE ,KIGNORE ,KIGNORE ,KIGNORE , -}; - -ushort *key_maps[MAX_NR_KEYMAPS] = { - plain_map, shift_map, altgr_map, 0, - ctrl_map, shift_ctrl_map, 0, 0, - alt_map, 0, 0, 0, - ctrl_alt_map, 0 -}; - -unsigned int keymap_count = 7; - -/* - * Philosophy: most people do not define more strings, but they who do - * often want quite a lot of string space. So, we statically allocate - * the default and allocate dynamically in chunks of 512 bytes. - */ - -char func_buf[] = { - '\033', '[', '[', 'A', 0, - '\033', '[', '[', 'B', 0, - '\033', '[', '[', 'C', 0, - '\033', '[', '[', 'D', 0, - '\033', '[', '[', 'E', 0, - '\033', '[', '1', '7', '~', 0, - '\033', '[', '1', '8', '~', 0, - '\033', '[', '1', '9', '~', 0, - '\033', '[', '2', '0', '~', 0, - '\033', '[', '2', '1', '~', 0, - '\033', '[', '2', '3', '~', 0, - '\033', '[', '2', '4', '~', 0, - '\033', '[', '2', '5', '~', 0, - '\033', '[', '2', '6', '~', 0, - '\033', '[', '2', '8', '~', 0, - '\033', '[', '2', '9', '~', 0, - '\033', '[', '3', '1', '~', 0, - '\033', '[', '3', '2', '~', 0, - '\033', '[', '3', '3', '~', 0, - '\033', '[', '3', '4', '~', 0, - '\033', '[', '1', '~', 0, - '\033', '[', '2', '~', 0, - '\033', '[', '3', '~', 0, - '\033', '[', '4', '~', 0, - '\033', '[', '5', '~', 0, - '\033', '[', '6', '~', 0, - '\033', '[', 'M', 0, - '\033', '[', 'P', 0, -}; - -char *funcbufptr = func_buf; -int funcbufsize = sizeof(func_buf); -int funcbufleft = 0; /* space left */ - -char *func_table[MAX_NR_FUNC] = { - func_buf + 0, - func_buf + 5, - func_buf + 10, - func_buf + 15, - func_buf + 20, - func_buf + 25, - func_buf + 31, - func_buf + 37, - func_buf + 43, - func_buf + 49, - func_buf + 55, - func_buf + 61, - func_buf + 67, - func_buf + 73, - func_buf + 79, - func_buf + 85, - func_buf + 91, - func_buf + 97, - func_buf + 103, - func_buf + 109, - func_buf + 115, - func_buf + 120, - func_buf + 125, - func_buf + 130, - func_buf + 135, - func_buf + 140, - func_buf + 145, - 0, - 0, - func_buf + 149, - 0, -}; - -struct kbdiacruc accent_table[MAX_DIACR] = { - {'`', 'A', 0300}, {'`', 'a', 0340}, - {'\'', 'A', 0301}, {'\'', 'a', 0341}, - {'^', 'A', 0302}, {'^', 'a', 0342}, - {'~', 'A', 0303}, {'~', 'a', 0343}, - {'"', 'A', 0304}, {'"', 'a', 0344}, - {'O', 'A', 0305}, {'o', 'a', 0345}, - {'0', 'A', 0305}, {'0', 'a', 0345}, - {'A', 'A', 0305}, {'a', 'a', 0345}, - {'A', 'E', 0306}, {'a', 'e', 0346}, - {',', 'C', 0307}, {',', 'c', 0347}, - {'`', 'E', 0310}, {'`', 'e', 0350}, - {'\'', 'E', 0311}, {'\'', 'e', 0351}, - {'^', 'E', 0312}, {'^', 'e', 0352}, - {'"', 'E', 0313}, {'"', 'e', 0353}, - {'`', 'I', 0314}, {'`', 'i', 0354}, - {'\'', 'I', 0315}, {'\'', 'i', 0355}, - {'^', 'I', 0316}, {'^', 'i', 0356}, - {'"', 'I', 0317}, {'"', 'i', 0357}, - {'-', 'D', 0320}, {'-', 'd', 0360}, - {'~', 'N', 0321}, {'~', 'n', 0361}, - {'`', 'O', 0322}, {'`', 'o', 0362}, - {'\'', 'O', 0323}, {'\'', 'o', 0363}, - {'^', 'O', 0324}, {'^', 'o', 0364}, - {'~', 'O', 0325}, {'~', 'o', 0365}, - {'"', 'O', 0326}, {'"', 'o', 0366}, - {'/', 'O', 0330}, {'/', 'o', 0370}, - {'`', 'U', 0331}, {'`', 'u', 0371}, - {'\'', 'U', 0332}, {'\'', 'u', 0372}, - {'^', 'U', 0333}, {'^', 'u', 0373}, - {'"', 'U', 0334}, {'"', 'u', 0374}, - {'\'', 'Y', 0335}, {'\'', 'y', 0375}, - {'T', 'H', 0336}, {'t', 'h', 0376}, - {'s', 's', 0337}, {'"', 'y', 0377}, - {'s', 'z', 0337}, {'i', 'j', 0377}, -}; - -unsigned int accent_table_size = 68; diff --git a/drivers/i2c/chips/isp1301_omap.c b/drivers/i2c/chips/isp1301_omap.c index b1b45dddb17..03a33f1b9cd 100644 --- a/drivers/i2c/chips/isp1301_omap.c +++ b/drivers/i2c/chips/isp1301_omap.c @@ -72,7 +72,7 @@ struct isp1301 { }; -/* bits in OTG_CTRL_REG */ +/* bits in OTG_CTRL */ #define OTG_XCEIV_OUTPUTS \ (OTG_ASESSVLD|OTG_BSESSEND|OTG_BSESSVLD|OTG_VBUSVLD|OTG_ID) @@ -186,8 +186,8 @@ isp1301_clear_bits(struct isp1301 *isp, u8 reg, u8 bits) /* operational registers */ #define ISP1301_MODE_CONTROL_1 0x04 /* u8 read, set, +1 clear */ -# define MC1_SPEED_REG (1 << 0) -# define MC1_SUSPEND_REG (1 << 1) +# define MC1_SPEED (1 << 0) +# define MC1_SUSPEND (1 << 1) # define MC1_DAT_SE0 (1 << 2) # define MC1_TRANSPARENT (1 << 3) # define MC1_BDIS_ACON_EN (1 << 4) @@ -274,7 +274,7 @@ static void power_down(struct isp1301 *isp) isp->otg.state = OTG_STATE_UNDEFINED; // isp1301_set_bits(isp, ISP1301_MODE_CONTROL_2, MC2_GLOBAL_PWR_DN); - isp1301_set_bits(isp, ISP1301_MODE_CONTROL_1, MC1_SUSPEND_REG); + isp1301_set_bits(isp, ISP1301_MODE_CONTROL_1, MC1_SUSPEND); isp1301_clear_bits(isp, ISP1301_OTG_CONTROL_1, OTG1_ID_PULLDOWN); isp1301_clear_bits(isp, ISP1301_MODE_CONTROL_1, MC1_DAT_SE0); @@ -283,7 +283,7 @@ static void power_down(struct isp1301 *isp) static void power_up(struct isp1301 *isp) { // isp1301_clear_bits(isp, ISP1301_MODE_CONTROL_2, MC2_GLOBAL_PWR_DN); - isp1301_clear_bits(isp, ISP1301_MODE_CONTROL_1, MC1_SUSPEND_REG); + isp1301_clear_bits(isp, ISP1301_MODE_CONTROL_1, MC1_SUSPEND); /* do this only when cpu is driving transceiver, * so host won't see a low speed device... @@ -360,6 +360,8 @@ isp1301_defer_work(struct isp1301 *isp, int work) /* called from irq handlers */ static void a_idle(struct isp1301 *isp, const char *tag) { + u32 l; + if (isp->otg.state == OTG_STATE_A_IDLE) return; @@ -373,13 +375,17 @@ static void a_idle(struct isp1301 *isp, const char *tag) gadget_suspend(isp); } isp->otg.state = OTG_STATE_A_IDLE; - isp->last_otg_ctrl = OTG_CTRL_REG = OTG_CTRL_REG & OTG_XCEIV_OUTPUTS; + l = omap_readl(OTG_CTRL) & OTG_XCEIV_OUTPUTS; + omap_writel(l, OTG_CTRL); + isp->last_otg_ctrl = l; pr_debug(" --> %s/%s\n", state_name(isp), tag); } /* called from irq handlers */ static void b_idle(struct isp1301 *isp, const char *tag) { + u32 l; + if (isp->otg.state == OTG_STATE_B_IDLE) return; @@ -393,7 +399,9 @@ static void b_idle(struct isp1301 *isp, const char *tag) gadget_suspend(isp); } isp->otg.state = OTG_STATE_B_IDLE; - isp->last_otg_ctrl = OTG_CTRL_REG = OTG_CTRL_REG & OTG_XCEIV_OUTPUTS; + l = omap_readl(OTG_CTRL) & OTG_XCEIV_OUTPUTS; + omap_writel(l, OTG_CTRL); + isp->last_otg_ctrl = l; pr_debug(" --> %s/%s\n", state_name(isp), tag); } @@ -406,7 +414,7 @@ dump_regs(struct isp1301 *isp, const char *label) u8 src = isp1301_get_u8(isp, ISP1301_INTERRUPT_SOURCE); pr_debug("otg: %06x, %s %s, otg/%02x stat/%02x.%02x\n", - OTG_CTRL_REG, label, state_name(isp), + omap_readl(OTG_CTRL), label, state_name(isp), ctrl, status, src); /* mode control and irq enables don't change much */ #endif @@ -429,7 +437,7 @@ dump_regs(struct isp1301 *isp, const char *label) static void check_state(struct isp1301 *isp, const char *tag) { enum usb_otg_state state = OTG_STATE_UNDEFINED; - u8 fsm = OTG_TEST_REG & 0x0ff; + u8 fsm = omap_readw(OTG_TEST) & 0x0ff; unsigned extra = 0; switch (fsm) { @@ -494,7 +502,8 @@ static void check_state(struct isp1301 *isp, const char *tag) if (isp->otg.state == state && !extra) return; pr_debug("otg: %s FSM %s/%02x, %s, %06x\n", tag, - state_string(state), fsm, state_name(isp), OTG_CTRL_REG); + state_string(state), fsm, state_name(isp), + omap_readl(OTG_CTRL)); } #else @@ -508,10 +517,11 @@ static void update_otg1(struct isp1301 *isp, u8 int_src) { u32 otg_ctrl; - otg_ctrl = OTG_CTRL_REG - & OTG_CTRL_MASK - & ~OTG_XCEIV_INPUTS - & ~(OTG_ID|OTG_ASESSVLD|OTG_VBUSVLD); + otg_ctrl = omap_readl(OTG_CTRL) & OTG_CTRL_MASK; + otg_ctrl &= ~OTG_XCEIV_INPUTS; + otg_ctrl &= ~(OTG_ID|OTG_ASESSVLD|OTG_VBUSVLD); + + if (int_src & INTR_SESS_VLD) otg_ctrl |= OTG_ASESSVLD; else if (isp->otg.state == OTG_STATE_A_WAIT_VFALL) { @@ -534,7 +544,7 @@ static void update_otg1(struct isp1301 *isp, u8 int_src) return; } } - OTG_CTRL_REG = otg_ctrl; + omap_writel(otg_ctrl, OTG_CTRL); } /* outputs from ISP1301_OTG_STATUS */ @@ -542,15 +552,14 @@ static void update_otg2(struct isp1301 *isp, u8 otg_status) { u32 otg_ctrl; - otg_ctrl = OTG_CTRL_REG - & OTG_CTRL_MASK - & ~OTG_XCEIV_INPUTS - & ~(OTG_BSESSVLD|OTG_BSESSEND); + otg_ctrl = omap_readl(OTG_CTRL) & OTG_CTRL_MASK; + otg_ctrl &= ~OTG_XCEIV_INPUTS; + otg_ctrl &= ~(OTG_BSESSVLD | OTG_BSESSEND); if (otg_status & OTG_B_SESS_VLD) otg_ctrl |= OTG_BSESSVLD; else if (otg_status & OTG_B_SESS_END) otg_ctrl |= OTG_BSESSEND; - OTG_CTRL_REG = otg_ctrl; + omap_writel(otg_ctrl, OTG_CTRL); } /* inputs going to ISP1301 */ @@ -559,7 +568,7 @@ static void otg_update_isp(struct isp1301 *isp) u32 otg_ctrl, otg_change; u8 set = OTG1_DM_PULLDOWN, clr = OTG1_DM_PULLUP; - otg_ctrl = OTG_CTRL_REG; + otg_ctrl = omap_readl(OTG_CTRL); otg_change = otg_ctrl ^ isp->last_otg_ctrl; isp->last_otg_ctrl = otg_ctrl; otg_ctrl = otg_ctrl & OTG_XCEIV_INPUTS; @@ -639,6 +648,8 @@ pulldown: /* HNP switch to host or peripheral; and SRP */ if (otg_change & OTG_PULLUP) { + u32 l; + switch (isp->otg.state) { case OTG_STATE_B_IDLE: if (clr & OTG1_DP_PULLUP) @@ -655,7 +666,9 @@ pulldown: default: break; } - OTG_CTRL_REG |= OTG_PULLUP; + l = omap_readl(OTG_CTRL); + l |= OTG_PULLUP; + omap_writel(l, OTG_CTRL); } check_state(isp, __func__); @@ -664,20 +677,20 @@ pulldown: static irqreturn_t omap_otg_irq(int irq, void *_isp) { - u16 otg_irq = OTG_IRQ_SRC_REG; + u16 otg_irq = omap_readw(OTG_IRQ_SRC); u32 otg_ctrl; int ret = IRQ_NONE; struct isp1301 *isp = _isp; /* update ISP1301 transciever from OTG controller */ if (otg_irq & OPRT_CHG) { - OTG_IRQ_SRC_REG = OPRT_CHG; + omap_writew(OPRT_CHG, OTG_IRQ_SRC); isp1301_defer_work(isp, WORK_UPDATE_ISP); ret = IRQ_HANDLED; /* SRP to become b_peripheral failed */ } else if (otg_irq & B_SRP_TMROUT) { - pr_debug("otg: B_SRP_TIMEOUT, %06x\n", OTG_CTRL_REG); + pr_debug("otg: B_SRP_TIMEOUT, %06x\n", omap_readl(OTG_CTRL)); notresponding(isp); /* gadget drivers that care should monitor all kinds of @@ -687,31 +700,31 @@ static irqreturn_t omap_otg_irq(int irq, void *_isp) if (isp->otg.state == OTG_STATE_B_SRP_INIT) b_idle(isp, "srp_timeout"); - OTG_IRQ_SRC_REG = B_SRP_TMROUT; + omap_writew(B_SRP_TMROUT, OTG_IRQ_SRC); ret = IRQ_HANDLED; /* HNP to become b_host failed */ } else if (otg_irq & B_HNP_FAIL) { pr_debug("otg: %s B_HNP_FAIL, %06x\n", - state_name(isp), OTG_CTRL_REG); + state_name(isp), omap_readl(OTG_CTRL)); notresponding(isp); - otg_ctrl = OTG_CTRL_REG; + otg_ctrl = omap_readl(OTG_CTRL); otg_ctrl |= OTG_BUSDROP; otg_ctrl &= OTG_CTRL_MASK & ~OTG_XCEIV_INPUTS; - OTG_CTRL_REG = otg_ctrl; + omap_writel(otg_ctrl, OTG_CTRL); /* subset of b_peripheral()... */ isp->otg.state = OTG_STATE_B_PERIPHERAL; pr_debug(" --> b_peripheral\n"); - OTG_IRQ_SRC_REG = B_HNP_FAIL; + omap_writew(B_HNP_FAIL, OTG_IRQ_SRC); ret = IRQ_HANDLED; /* detect SRP from B-device ... */ } else if (otg_irq & A_SRP_DETECT) { pr_debug("otg: %s SRP_DETECT, %06x\n", - state_name(isp), OTG_CTRL_REG); + state_name(isp), omap_readl(OTG_CTRL)); isp1301_defer_work(isp, WORK_UPDATE_OTG); switch (isp->otg.state) { @@ -719,49 +732,49 @@ static irqreturn_t omap_otg_irq(int irq, void *_isp) if (!isp->otg.host) break; isp1301_defer_work(isp, WORK_HOST_RESUME); - otg_ctrl = OTG_CTRL_REG; + otg_ctrl = omap_readl(OTG_CTRL); otg_ctrl |= OTG_A_BUSREQ; otg_ctrl &= ~(OTG_BUSDROP|OTG_B_BUSREQ) & ~OTG_XCEIV_INPUTS & OTG_CTRL_MASK; - OTG_CTRL_REG = otg_ctrl; + omap_writel(otg_ctrl, OTG_CTRL); break; default: break; } - OTG_IRQ_SRC_REG = A_SRP_DETECT; + omap_writew(A_SRP_DETECT, OTG_IRQ_SRC); ret = IRQ_HANDLED; /* timer expired: T(a_wait_bcon) and maybe T(a_wait_vrise) * we don't track them separately */ } else if (otg_irq & A_REQ_TMROUT) { - otg_ctrl = OTG_CTRL_REG; + otg_ctrl = omap_readl(OTG_CTRL); pr_info("otg: BCON_TMOUT from %s, %06x\n", state_name(isp), otg_ctrl); notresponding(isp); otg_ctrl |= OTG_BUSDROP; otg_ctrl &= ~OTG_A_BUSREQ & OTG_CTRL_MASK & ~OTG_XCEIV_INPUTS; - OTG_CTRL_REG = otg_ctrl; + omap_writel(otg_ctrl, OTG_CTRL); isp->otg.state = OTG_STATE_A_WAIT_VFALL; - OTG_IRQ_SRC_REG = A_REQ_TMROUT; + omap_writew(A_REQ_TMROUT, OTG_IRQ_SRC); ret = IRQ_HANDLED; /* A-supplied voltage fell too low; overcurrent */ } else if (otg_irq & A_VBUS_ERR) { - otg_ctrl = OTG_CTRL_REG; + otg_ctrl = omap_readl(OTG_CTRL); printk(KERN_ERR "otg: %s, VBUS_ERR %04x ctrl %06x\n", state_name(isp), otg_irq, otg_ctrl); otg_ctrl |= OTG_BUSDROP; otg_ctrl &= ~OTG_A_BUSREQ & OTG_CTRL_MASK & ~OTG_XCEIV_INPUTS; - OTG_CTRL_REG = otg_ctrl; + omap_writel(otg_ctrl, OTG_CTRL); isp->otg.state = OTG_STATE_A_VBUS_ERR; - OTG_IRQ_SRC_REG = A_VBUS_ERR; + omap_writew(A_VBUS_ERR, OTG_IRQ_SRC); ret = IRQ_HANDLED; /* switch driver; the transciever code activates it, @@ -770,7 +783,7 @@ static irqreturn_t omap_otg_irq(int irq, void *_isp) } else if (otg_irq & DRIVER_SWITCH) { int kick = 0; - otg_ctrl = OTG_CTRL_REG; + otg_ctrl = omap_readl(OTG_CTRL); printk(KERN_NOTICE "otg: %s, SWITCH to %s, ctrl %06x\n", state_name(isp), (otg_ctrl & OTG_DRIVER_SEL) @@ -793,7 +806,7 @@ static irqreturn_t omap_otg_irq(int irq, void *_isp) } else { if (!(otg_ctrl & OTG_ID)) { otg_ctrl &= OTG_CTRL_MASK & ~OTG_XCEIV_INPUTS; - OTG_CTRL_REG = otg_ctrl | OTG_A_BUSREQ; + omap_writel(otg_ctrl | OTG_A_BUSREQ, OTG_CTRL); } if (isp->otg.host) { @@ -818,7 +831,7 @@ static irqreturn_t omap_otg_irq(int irq, void *_isp) } } - OTG_IRQ_SRC_REG = DRIVER_SWITCH; + omap_writew(DRIVER_SWITCH, OTG_IRQ_SRC); ret = IRQ_HANDLED; if (kick) @@ -834,12 +847,15 @@ static struct platform_device *otg_dev; static int otg_init(struct isp1301 *isp) { + u32 l; + if (!otg_dev) return -ENODEV; dump_regs(isp, __func__); /* some of these values are board-specific... */ - OTG_SYSCON_2_REG |= OTG_EN + l = omap_readl(OTG_SYSCON_2); + l |= OTG_EN /* for B-device: */ | SRP_GPDATA /* 9msec Bdev D+ pulse */ | SRP_GPDVBUS /* discharge after VBUS pulse */ @@ -849,18 +865,22 @@ static int otg_init(struct isp1301 *isp) | SRP_DPW /* detect 167+ns SRP pulses */ | SRP_DATA | SRP_VBUS /* accept both kinds of SRP pulse */ ; + omap_writel(l, OTG_SYSCON_2); update_otg1(isp, isp1301_get_u8(isp, ISP1301_INTERRUPT_SOURCE)); update_otg2(isp, isp1301_get_u8(isp, ISP1301_OTG_STATUS)); check_state(isp, __func__); pr_debug("otg: %s, %s %06x\n", - state_name(isp), __func__, OTG_CTRL_REG); + state_name(isp), __func__, omap_readl(OTG_CTRL)); - OTG_IRQ_EN_REG = DRIVER_SWITCH | OPRT_CHG + omap_writew(DRIVER_SWITCH | OPRT_CHG | B_SRP_TMROUT | B_HNP_FAIL - | A_VBUS_ERR | A_SRP_DETECT | A_REQ_TMROUT; - OTG_SYSCON_2_REG |= OTG_EN; + | A_VBUS_ERR | A_SRP_DETECT | A_REQ_TMROUT, OTG_IRQ_EN); + + l = omap_readl(OTG_SYSCON_2); + l |= OTG_EN; + omap_writel(l, OTG_SYSCON_2); return 0; } @@ -927,7 +947,11 @@ static void otg_unbind(struct isp1301 *isp) static void b_peripheral(struct isp1301 *isp) { - OTG_CTRL_REG = OTG_CTRL_REG & OTG_XCEIV_OUTPUTS; + u32 l; + + l = omap_readl(OTG_CTRL) & OTG_XCEIV_OUTPUTS; + omap_writel(l, OTG_CTRL); + usb_gadget_vbus_connect(isp->otg.gadget); #ifdef CONFIG_USB_OTG @@ -999,6 +1023,8 @@ static void isp_update_otg(struct isp1301 *isp, u8 stat) isp_bstat = 0; } } else { + u32 l; + /* if user unplugged mini-A end of cable, * don't bypass A_WAIT_VFALL. */ @@ -1019,8 +1045,9 @@ static void isp_update_otg(struct isp1301 *isp, u8 stat) isp1301_clear_bits(isp, ISP1301_MODE_CONTROL_1, MC1_BDIS_ACON_EN); isp->otg.state = OTG_STATE_B_IDLE; - OTG_CTRL_REG &= OTG_CTRL_REG & OTG_CTRL_MASK - & ~OTG_CTRL_BITS; + l = omap_readl(OTG_CTRL) & OTG_CTRL_MASK; + l &= ~OTG_CTRL_BITS; + omap_writel(l, OTG_CTRL); break; case OTG_STATE_B_IDLE: break; @@ -1046,7 +1073,8 @@ static void isp_update_otg(struct isp1301 *isp, u8 stat) /* FALLTHROUGH */ case OTG_STATE_B_SRP_INIT: b_idle(isp, __func__); - OTG_CTRL_REG &= OTG_CTRL_REG & OTG_XCEIV_OUTPUTS; + l = omap_readl(OTG_CTRL) & OTG_XCEIV_OUTPUTS; + omap_writel(l, OTG_CTRL); /* FALLTHROUGH */ case OTG_STATE_B_IDLE: if (isp->otg.gadget && (isp_bstat & OTG_B_SESS_VLD)) { @@ -1130,11 +1158,11 @@ isp1301_work(struct work_struct *work) case OTG_STATE_A_WAIT_VRISE: isp->otg.state = OTG_STATE_A_HOST; pr_debug(" --> a_host\n"); - otg_ctrl = OTG_CTRL_REG; + otg_ctrl = omap_readl(OTG_CTRL); otg_ctrl |= OTG_A_BUSREQ; otg_ctrl &= ~(OTG_BUSDROP|OTG_B_BUSREQ) & OTG_CTRL_MASK; - OTG_CTRL_REG = otg_ctrl; + omap_writel(otg_ctrl, OTG_CTRL); break; case OTG_STATE_B_WAIT_ACON: isp->otg.state = OTG_STATE_B_HOST; @@ -1274,7 +1302,7 @@ isp1301_set_host(struct otg_transceiver *otg, struct usb_bus *host) return -ENODEV; if (!host) { - OTG_IRQ_EN_REG = 0; + omap_writew(0, OTG_IRQ_EN); power_down(isp); isp->otg.host = 0; return 0; @@ -1325,12 +1353,13 @@ static int isp1301_set_peripheral(struct otg_transceiver *otg, struct usb_gadget *gadget) { struct isp1301 *isp = container_of(otg, struct isp1301, otg); + u32 l; if (!otg || isp != the_transceiver) return -ENODEV; if (!gadget) { - OTG_IRQ_EN_REG = 0; + omap_writew(0, OTG_IRQ_EN); if (!isp->otg.default_a) enable_vbus_draw(isp, 0); usb_gadget_vbus_disconnect(isp->otg.gadget); @@ -1351,9 +1380,11 @@ isp1301_set_peripheral(struct otg_transceiver *otg, struct usb_gadget *gadget) isp->otg.gadget = gadget; // FIXME update its refcount - OTG_CTRL_REG = (OTG_CTRL_REG & OTG_CTRL_MASK - & ~(OTG_XCEIV_OUTPUTS|OTG_CTRL_BITS)) - | OTG_ID; + l = omap_readl(OTG_CTRL) & OTG_CTRL_MASK; + l &= ~(OTG_XCEIV_OUTPUTS|OTG_CTRL_BITS); + l |= OTG_ID; + omap_writel(l, OTG_CTRL); + power_up(isp); isp->otg.state = OTG_STATE_B_IDLE; @@ -1405,16 +1436,17 @@ isp1301_start_srp(struct otg_transceiver *dev) || isp->otg.state != OTG_STATE_B_IDLE) return -ENODEV; - otg_ctrl = OTG_CTRL_REG; + otg_ctrl = omap_readl(OTG_CTRL); if (!(otg_ctrl & OTG_BSESSEND)) return -EINVAL; otg_ctrl |= OTG_B_BUSREQ; otg_ctrl &= ~OTG_A_BUSREQ & OTG_CTRL_MASK; - OTG_CTRL_REG = otg_ctrl; + omap_writel(otg_ctrl, OTG_CTRL); isp->otg.state = OTG_STATE_B_SRP_INIT; - pr_debug("otg: SRP, %s ... %06x\n", state_name(isp), OTG_CTRL_REG); + pr_debug("otg: SRP, %s ... %06x\n", state_name(isp), + omap_readl(OTG_CTRL)); #ifdef CONFIG_USB_OTG check_state(isp, __func__); #endif @@ -1426,6 +1458,7 @@ isp1301_start_hnp(struct otg_transceiver *dev) { #ifdef CONFIG_USB_OTG struct isp1301 *isp = container_of(dev, struct isp1301, otg); + u32 l; if (!dev || isp != the_transceiver) return -ENODEV; @@ -1452,7 +1485,9 @@ isp1301_start_hnp(struct otg_transceiver *dev) #endif /* caller must suspend then clear A_BUSREQ */ usb_gadget_vbus_connect(isp->otg.gadget); - OTG_CTRL_REG |= OTG_A_SETB_HNPEN; + l = omap_readl(OTG_CTRL); + l |= OTG_A_SETB_HNPEN; + omap_writel(l, OTG_CTRL); break; case OTG_STATE_A_PERIPHERAL: @@ -1462,7 +1497,7 @@ isp1301_start_hnp(struct otg_transceiver *dev) return -EILSEQ; } pr_debug("otg: HNP %s, %06x ...\n", - state_name(isp), OTG_CTRL_REG); + state_name(isp), omap_readl(OTG_CTRL)); check_state(isp, __func__); return 0; #else diff --git a/drivers/mmc/host/imxmmc.c b/drivers/mmc/host/imxmmc.c index ef2f6fc8654..eed211b2ac7 100644 --- a/drivers/mmc/host/imxmmc.c +++ b/drivers/mmc/host/imxmmc.c @@ -1027,8 +1027,8 @@ static int imxmci_probe(struct platform_device *pdev) host->imask = IMXMCI_INT_MASK_DEFAULT; MMC_INT_MASK = host->imask; - - if(imx_dma_request_by_prio(&host->dma, DRIVER_NAME, DMA_PRIO_LOW)<0){ + host->dma = imx_dma_request_by_prio(DRIVER_NAME, DMA_PRIO_LOW); + if(host->dma < 0) { dev_err(mmc_dev(host->mmc), "imx_dma_request_by_prio failed\n"); ret = -EBUSY; goto out; diff --git a/drivers/mtd/maps/omap_nor.c b/drivers/mtd/maps/omap_nor.c index c12d8056beb..68eec6c6c51 100644 --- a/drivers/mtd/maps/omap_nor.c +++ b/drivers/mtd/maps/omap_nor.c @@ -60,13 +60,22 @@ struct omapflash_info { static void omap_set_vpp(struct map_info *map, int enable) { static int count; - - if (enable) { - if (count++ == 0) - OMAP_EMIFS_CONFIG_REG |= OMAP_EMIFS_CONFIG_WP; - } else { - if (count && (--count == 0)) - OMAP_EMIFS_CONFIG_REG &= ~OMAP_EMIFS_CONFIG_WP; + u32 l; + + if (cpu_class_is_omap1()) { + if (enable) { + if (count++ == 0) { + l = omap_readl(EMIFS_CONFIG); + l |= OMAP_EMIFS_CONFIG_WP; + omap_writel(l, EMIFS_CONFIG); + } + } else { + if (count && (--count == 0)) { + l = omap_readl(EMIFS_CONFIG); + l &= ~OMAP_EMIFS_CONFIG_WP; + omap_writel(l, EMIFS_CONFIG); + } + } } } diff --git a/drivers/mtd/nand/orion_nand.c b/drivers/mtd/nand/orion_nand.c index 59e05a1c50c..ee2ac3948cd 100644 --- a/drivers/mtd/nand/orion_nand.c +++ b/drivers/mtd/nand/orion_nand.c @@ -85,6 +85,9 @@ static int __init orion_nand_probe(struct platform_device *pdev) nc->cmd_ctrl = orion_nand_cmd_ctrl; nc->ecc.mode = NAND_ECC_SOFT; + if (board->chip_delay) + nc->chip_delay = board->chip_delay; + if (board->width == 16) nc->options |= NAND_BUSWIDTH_16; diff --git a/drivers/net/Kconfig b/drivers/net/Kconfig index f4182cfffe9..45a41b597da 100644 --- a/drivers/net/Kconfig +++ b/drivers/net/Kconfig @@ -217,7 +217,7 @@ config MII config MACB tristate "Atmel MACB support" - depends on AVR32 || ARCH_AT91SAM9260 || ARCH_AT91SAM9263 || ARCH_AT91CAP9 + depends on AVR32 || ARCH_AT91SAM9260 || ARCH_AT91SAM9263 || ARCH_AT91SAM9G20 || ARCH_AT91CAP9 select PHYLIB help The Atmel MACB ethernet interface is found on many AT32 and AT91 diff --git a/drivers/net/arm/etherh.c b/drivers/net/arm/etherh.c index 00081d2b9cd..e9d15eccad0 100644 --- a/drivers/net/arm/etherh.c +++ b/drivers/net/arm/etherh.c @@ -647,7 +647,7 @@ etherh_probe(struct expansion_card *ec, const struct ecard_id *id) struct ei_device *ei_local; struct net_device *dev; struct etherh_priv *eh; - int i, ret; + int ret; DECLARE_MAC_BUF(mac); etherh_banner(); diff --git a/drivers/pcmcia/omap_cf.c b/drivers/pcmcia/omap_cf.c index 46314b42076..569b746b573 100644 --- a/drivers/pcmcia/omap_cf.c +++ b/drivers/pcmcia/omap_cf.c @@ -38,19 +38,19 @@ #define CF_BASE 0xfffe2800 /* status; read after IRQ */ -#define CF_STATUS_REG __REG16(CF_BASE + 0x00) +#define CF_STATUS (CF_BASE + 0x00) # define CF_STATUS_BAD_READ (1 << 2) # define CF_STATUS_BAD_WRITE (1 << 1) # define CF_STATUS_CARD_DETECT (1 << 0) /* which chipselect (CS0..CS3) is used for CF (active low) */ -#define CF_CFG_REG __REG16(CF_BASE + 0x02) +#define CF_CFG (CF_BASE + 0x02) /* card reset */ -#define CF_CONTROL_REG __REG16(CF_BASE + 0x04) +#define CF_CONTROL (CF_BASE + 0x04) # define CF_CONTROL_RESET (1 << 0) -#define omap_cf_present() (!(CF_STATUS_REG & CF_STATUS_CARD_DETECT)) +#define omap_cf_present() (!(omap_readw(CF_STATUS) & CF_STATUS_CARD_DETECT)) /*--------------------------------------------------------------------------*/ @@ -139,11 +139,11 @@ omap_cf_set_socket(struct pcmcia_socket *sock, struct socket_state_t *s) return -EINVAL; } - control = CF_CONTROL_REG; + control = omap_readw(CF_CONTROL); if (s->flags & SS_RESET) - CF_CONTROL_REG = CF_CONTROL_RESET; + omap_writew(CF_CONTROL_RESET, CF_CONTROL); else - CF_CONTROL_REG = 0; + omap_writew(0, CF_CONTROL); pr_debug("%s: Vcc %d, io_irq %d, flags %04x csc %04x\n", driver_name, s->Vcc, s->io_irq, s->flags, s->csc_mask); @@ -270,7 +270,7 @@ static int __init omap_cf_probe(struct platform_device *pdev) omap_cfg_reg(V10_1610_CF_IREQ); omap_cfg_reg(W10_1610_CF_RESET); - CF_CFG_REG = ~(1 << seg); + omap_writew(~(1 << seg), CF_CFG); pr_info("%s: cs%d on irq %d\n", driver_name, seg, irq); @@ -279,14 +279,15 @@ static int __init omap_cf_probe(struct platform_device *pdev) * CF/PCMCIA variants... */ pr_debug("%s: cs%d, previous ccs %08x acs %08x\n", driver_name, - seg, EMIFS_CCS(seg), EMIFS_ACS(seg)); - EMIFS_CCS(seg) = 0x0004a1b3; /* synch mode 4 etc */ - EMIFS_ACS(seg) = 0x00000000; /* OE hold/setup */ + seg, omap_readl(EMIFS_CCS(seg)), omap_readl(EMIFS_ACS(seg))); + omap_writel(0x0004a1b3, EMIFS_CCS(seg)); /* synch mode 4 etc */ + omap_writel(0x00000000, EMIFS_ACS(seg)); /* OE hold/setup */ /* CF uses armxor_ck, which is "always" available */ pr_debug("%s: sts %04x cfg %04x control %04x %s\n", driver_name, - CF_STATUS_REG, CF_CFG_REG, CF_CONTROL_REG, + omap_readw(CF_STATUS), omap_readw(CF_CFG), + omap_readw(CF_CONTROL), omap_cf_present() ? "present" : "(not present)"); cf->socket.owner = THIS_MODULE; diff --git a/drivers/rtc/Kconfig b/drivers/rtc/Kconfig index 4949dc4859b..fc85bf2e4a9 100644 --- a/drivers/rtc/Kconfig +++ b/drivers/rtc/Kconfig @@ -469,6 +469,16 @@ config RTC_DRV_VR41XX To compile this driver as a module, choose M here: the module will be called rtc-vr41xx. +config RTC_DRV_PL030 + tristate "ARM AMBA PL030 RTC" + depends on ARM_AMBA + help + If you say Y here you will get access to ARM AMBA + PrimeCell PL030 RTC found on certain ARM SOCs. + + To compile this driver as a module, choose M here: the + module will be called rtc-pl030. + config RTC_DRV_PL031 tristate "ARM AMBA PL031 RTC" depends on ARM_AMBA @@ -495,12 +505,13 @@ config RTC_DRV_AT91RM9200 this is powered by the backup power supply. config RTC_DRV_AT91SAM9 - tristate "AT91SAM9x" + tristate "AT91SAM9x/AT91CAP9" depends on ARCH_AT91 && !(ARCH_AT91RM9200 || ARCH_AT91X40) help - RTC driver for the Atmel AT91SAM9x internal RTT (Real Time Timer). - These timers are powered by the backup power supply (such as a - small coin cell battery), but do not need to be used as RTCs. + RTC driver for the Atmel AT91SAM9x and AT91CAP9 internal RTT + (Real Time Timer). These timers are powered by the backup power + supply (such as a small coin cell battery), but do not need to + be used as RTCs. (On AT91SAM9rl chips you probably want to use the dedicated RTC module and leave the RTT available for other uses.) diff --git a/drivers/rtc/Makefile b/drivers/rtc/Makefile index b6e14d51670..b5d9d67df88 100644 --- a/drivers/rtc/Makefile +++ b/drivers/rtc/Makefile @@ -41,6 +41,7 @@ obj-$(CONFIG_RTC_DRV_MAX6902) += rtc-max6902.o obj-$(CONFIG_RTC_DRV_OMAP) += rtc-omap.o obj-$(CONFIG_RTC_DRV_PCF8563) += rtc-pcf8563.o obj-$(CONFIG_RTC_DRV_PCF8583) += rtc-pcf8583.o +obj-$(CONFIG_RTC_DRV_PL030) += rtc-pl030.o obj-$(CONFIG_RTC_DRV_PL031) += rtc-pl031.o obj-$(CONFIG_RTC_DRV_PPC) += rtc-ppc.o obj-$(CONFIG_RTC_DRV_R9701) += rtc-r9701.o diff --git a/drivers/rtc/rtc-at91rm9200.c b/drivers/rtc/rtc-at91rm9200.c index 39e64ab1ecb..9c3db934cc2 100644 --- a/drivers/rtc/rtc-at91rm9200.c +++ b/drivers/rtc/rtc-at91rm9200.c @@ -29,10 +29,6 @@ #include <linux/completion.h> #include <asm/uaccess.h> -#include <asm/rtc.h> - -#include <asm/mach/time.h> - #include <asm/arch/at91_rtc.h> diff --git a/drivers/rtc/rtc-at91sam9.c b/drivers/rtc/rtc-at91sam9.c index 38d8742a4bd..f0246ef413a 100644 --- a/drivers/rtc/rtc-at91sam9.c +++ b/drivers/rtc/rtc-at91sam9.c @@ -19,7 +19,6 @@ #include <linux/interrupt.h> #include <linux/ioctl.h> -#include <asm/mach/time.h> #include <asm/arch/board.h> #include <asm/arch/at91_rtt.h> diff --git a/drivers/rtc/rtc-omap.c b/drivers/rtc/rtc-omap.c index 58f81c77494..eb23d8423f4 100644 --- a/drivers/rtc/rtc-omap.c +++ b/drivers/rtc/rtc-omap.c @@ -22,7 +22,6 @@ #include <linux/platform_device.h> #include <asm/io.h> -#include <asm/mach/time.h> /* The OMAP1 RTC is a year/month/day/hours/minutes/seconds BCD clock diff --git a/drivers/rtc/rtc-pl030.c b/drivers/rtc/rtc-pl030.c new file mode 100644 index 00000000000..8448eeb9d67 --- /dev/null +++ b/drivers/rtc/rtc-pl030.c @@ -0,0 +1,217 @@ +/* + * linux/drivers/rtc/rtc-pl030.c + * + * Copyright (C) 2000-2001 Deep Blue Solutions Ltd. + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ +#include <linux/module.h> +#include <linux/rtc.h> +#include <linux/init.h> +#include <linux/interrupt.h> +#include <linux/amba/bus.h> +#include <linux/io.h> + +#define RTC_DR (0) +#define RTC_MR (4) +#define RTC_STAT (8) +#define RTC_EOI (8) +#define RTC_LR (12) +#define RTC_CR (16) +#define RTC_CR_MIE (1 << 0) + +struct pl030_rtc { + struct rtc_device *rtc; + void __iomem *base; +}; + +static irqreturn_t pl030_interrupt(int irq, void *dev_id) +{ + struct pl030_rtc *rtc = dev_id; + writel(0, rtc->base + RTC_EOI); + return IRQ_HANDLED; +} + +static int pl030_open(struct device *dev) +{ + return 0; +} + +static void pl030_release(struct device *dev) +{ +} + +static int pl030_ioctl(struct device *dev, unsigned int cmd, unsigned long arg) +{ + return -ENOIOCTLCMD; +} + +static int pl030_read_alarm(struct device *dev, struct rtc_wkalrm *alrm) +{ + struct pl030_rtc *rtc = dev_get_drvdata(dev); + + rtc_time_to_tm(readl(rtc->base + RTC_MR), &alrm->time); + return 0; +} + +static int pl030_set_alarm(struct device *dev, struct rtc_wkalrm *alrm) +{ + struct pl030_rtc *rtc = dev_get_drvdata(dev); + unsigned long time; + int ret; + + /* + * At the moment, we can only deal with non-wildcarded alarm times. + */ + ret = rtc_valid_tm(&alrm->time); + if (ret == 0) + ret = rtc_tm_to_time(&alrm->time, &time); + if (ret == 0) + writel(time, rtc->base + RTC_MR); + return ret; +} + +static int pl030_read_time(struct device *dev, struct rtc_time *tm) +{ + struct pl030_rtc *rtc = dev_get_drvdata(dev); + + rtc_time_to_tm(readl(rtc->base + RTC_DR), tm); + + return 0; +} + +/* + * Set the RTC time. Unfortunately, we can't accurately set + * the point at which the counter updates. + * + * Also, since RTC_LR is transferred to RTC_CR on next rising + * edge of the 1Hz clock, we must write the time one second + * in advance. + */ +static int pl030_set_time(struct device *dev, struct rtc_time *tm) +{ + struct pl030_rtc *rtc = dev_get_drvdata(dev); + unsigned long time; + int ret; + + ret = rtc_tm_to_time(tm, &time); + if (ret == 0) + writel(time + 1, rtc->base + RTC_LR); + + return ret; +} + +static const struct rtc_class_ops pl030_ops = { + .open = pl030_open, + .release = pl030_release, + .ioctl = pl030_ioctl, + .read_time = pl030_read_time, + .set_time = pl030_set_time, + .read_alarm = pl030_read_alarm, + .set_alarm = pl030_set_alarm, +}; + +static int pl030_probe(struct amba_device *dev, void *id) +{ + struct pl030_rtc *rtc; + int ret; + + ret = amba_request_regions(dev, NULL); + if (ret) + goto err_req; + + rtc = kmalloc(sizeof(*rtc), GFP_KERNEL); + if (!rtc) { + ret = -ENOMEM; + goto err_rtc; + } + + rtc->base = ioremap(dev->res.start, SZ_4K); + if (!rtc->base) { + ret = -ENOMEM; + goto err_map; + } + + __raw_writel(0, rtc->base + RTC_CR); + __raw_writel(0, rtc->base + RTC_EOI); + + amba_set_drvdata(dev, rtc); + + ret = request_irq(dev->irq[0], pl030_interrupt, IRQF_DISABLED, + "rtc-pl030", rtc); + if (ret) + goto err_irq; + + rtc->rtc = rtc_device_register("pl030", &dev->dev, &pl030_ops, + THIS_MODULE); + if (IS_ERR(rtc->rtc)) { + ret = PTR_ERR(rtc->rtc); + goto err_reg; + } + + return 0; + + err_reg: + free_irq(dev->irq[0], rtc); + err_irq: + iounmap(rtc->base); + err_map: + kfree(rtc); + err_rtc: + amba_release_regions(dev); + err_req: + return ret; +} + +static int pl030_remove(struct amba_device *dev) +{ + struct pl030_rtc *rtc = amba_get_drvdata(dev); + + amba_set_drvdata(dev, NULL); + + writel(0, rtc->base + RTC_CR); + + free_irq(dev->irq[0], rtc); + rtc_device_unregister(rtc->rtc); + iounmap(rtc->base); + kfree(rtc); + amba_release_regions(dev); + + return 0; +} + +static struct amba_id pl030_ids[] = { + { + .id = 0x00041030, + .mask = 0x000fffff, + }, + { 0, 0 }, +}; + +static struct amba_driver pl030_driver = { + .drv = { + .name = "rtc-pl030", + }, + .probe = pl030_probe, + .remove = pl030_remove, + .id_table = pl030_ids, +}; + +static int __init pl030_init(void) +{ + return amba_driver_register(&pl030_driver); +} + +static void __exit pl030_exit(void) +{ + amba_driver_unregister(&pl030_driver); +} + +module_init(pl030_init); +module_exit(pl030_exit); + +MODULE_AUTHOR("Russell King <rmk@arm.linux.org.uk>"); +MODULE_DESCRIPTION("ARM AMBA PL030 RTC Driver"); +MODULE_LICENSE("GPL"); diff --git a/drivers/rtc/rtc-pl031.c b/drivers/rtc/rtc-pl031.c index 2fd49edcc71..08b4610ec5a 100644 --- a/drivers/rtc/rtc-pl031.c +++ b/drivers/rtc/rtc-pl031.c @@ -12,23 +12,12 @@ * as published by the Free Software Foundation; either version * 2 of the License, or (at your option) any later version. */ - -#include <linux/platform_device.h> #include <linux/module.h> #include <linux/rtc.h> #include <linux/init.h> -#include <linux/fs.h> #include <linux/interrupt.h> -#include <linux/string.h> -#include <linux/pm.h> -#include <linux/bitops.h> - #include <linux/amba/bus.h> - -#include <asm/io.h> -#include <asm/hardware.h> -#include <asm/irq.h> -#include <asm/rtc.h> +#include <linux/io.h> /* * Register definitions @@ -142,13 +131,12 @@ static int pl031_remove(struct amba_device *adev) { struct pl031_local *ldata = dev_get_drvdata(&adev->dev); - if (ldata) { - dev_set_drvdata(&adev->dev, NULL); - free_irq(adev->irq[0], ldata->rtc); - rtc_device_unregister(ldata->rtc); - iounmap(ldata->base); - kfree(ldata); - } + amba_set_drvdata(adev, NULL); + free_irq(adev->irq[0], ldata->rtc); + rtc_device_unregister(ldata->rtc); + iounmap(ldata->base); + kfree(ldata); + amba_release_regions(adev); return 0; } @@ -158,13 +146,15 @@ static int pl031_probe(struct amba_device *adev, void *id) int ret; struct pl031_local *ldata; + ret = amba_request_regions(adev, NULL); + if (ret) + goto err_req; ldata = kmalloc(sizeof(struct pl031_local), GFP_KERNEL); if (!ldata) { ret = -ENOMEM; goto out; } - dev_set_drvdata(&adev->dev, ldata); ldata->base = ioremap(adev->res.start, adev->res.end - adev->res.start + 1); @@ -173,6 +163,8 @@ static int pl031_probe(struct amba_device *adev, void *id) goto out_no_remap; } + amba_set_drvdata(adev, ldata); + if (request_irq(adev->irq[0], pl031_interrupt, IRQF_DISABLED, "rtc-pl031", ldata->rtc)) { ret = -EIO; @@ -192,10 +184,12 @@ out_no_rtc: free_irq(adev->irq[0], ldata->rtc); out_no_irq: iounmap(ldata->base); + amba_set_drvdata(adev, NULL); out_no_remap: - dev_set_drvdata(&adev->dev, NULL); kfree(ldata); out: + amba_release_regions(adev); +err_req: return ret; } diff --git a/drivers/rtc/rtc-s3c.c b/drivers/rtc/rtc-s3c.c index f26e0cad8f1..fed86e507fd 100644 --- a/drivers/rtc/rtc-s3c.c +++ b/drivers/rtc/rtc-s3c.c @@ -26,10 +26,6 @@ #include <asm/uaccess.h> #include <asm/io.h> #include <asm/irq.h> -#include <asm/rtc.h> - -#include <asm/mach/time.h> - #include <asm/plat-s3c/regs-rtc.h> /* I have yet to find an S3C implementation with more than one diff --git a/drivers/rtc/rtc-sa1100.c b/drivers/rtc/rtc-sa1100.c index 67421b0d3a7..f47294c6014 100644 --- a/drivers/rtc/rtc-sa1100.c +++ b/drivers/rtc/rtc-sa1100.c @@ -33,7 +33,6 @@ #include <asm/hardware.h> #include <asm/irq.h> -#include <asm/rtc.h> #ifdef CONFIG_ARCH_PXA #include <asm/arch/pxa-regs.h> @@ -47,6 +46,42 @@ static unsigned long rtc_freq = 1024; static struct rtc_time rtc_alarm; static DEFINE_SPINLOCK(sa1100_rtc_lock); +static inline int rtc_periodic_alarm(struct rtc_time *tm) +{ + return (tm->tm_year == -1) || + ((unsigned)tm->tm_mon >= 12) || + ((unsigned)(tm->tm_mday - 1) >= 31) || + ((unsigned)tm->tm_hour > 23) || + ((unsigned)tm->tm_min > 59) || + ((unsigned)tm->tm_sec > 59); +} + +/* + * Calculate the next alarm time given the requested alarm time mask + * and the current time. + */ +static void rtc_next_alarm_time(struct rtc_time *next, struct rtc_time *now, struct rtc_time *alrm) +{ + unsigned long next_time; + unsigned long now_time; + + next->tm_year = now->tm_year; + next->tm_mon = now->tm_mon; + next->tm_mday = now->tm_mday; + next->tm_hour = alrm->tm_hour; + next->tm_min = alrm->tm_min; + next->tm_sec = alrm->tm_sec; + + rtc_tm_to_time(now, &now_time); + rtc_tm_to_time(next, &next_time); + + if (next_time < now_time) { + /* Advance one day */ + next_time += 60 * 60 * 24; + rtc_time_to_tm(next_time, next); + } +} + static int rtc_update_alarm(struct rtc_time *alrm) { struct rtc_time alarm_tm, now_tm; diff --git a/drivers/scsi/arm/Kconfig b/drivers/scsi/arm/Kconfig index 7236143941f..a8587f1f5e7 100644 --- a/drivers/scsi/arm/Kconfig +++ b/drivers/scsi/arm/Kconfig @@ -3,7 +3,7 @@ # config SCSI_ACORNSCSI_3 tristate "Acorn SCSI card (aka30) support" - depends on ARCH_ACORN && SCSI && BROKEN + depends on ARCH_ACORN && SCSI select SCSI_SPI_ATTRS help This enables support for the Acorn SCSI card (aka30). If you have an diff --git a/drivers/scsi/arm/acornscsi-io.S b/drivers/scsi/arm/acornscsi-io.S index 93467e6ac92..5cebe310526 100644 --- a/drivers/scsi/arm/acornscsi-io.S +++ b/drivers/scsi/arm/acornscsi-io.S @@ -10,17 +10,10 @@ #include <asm/assembler.h> #include <asm/hardware.h> -#if (IO_BASE == (PCIO_BASE & 0xff000000)) -#define ADDR(off,reg) \ - tst off, $0x80000000 ;\ - mov reg, $IO_BASE ;\ - orreq reg, reg, $(PCIO_BASE & 0x00ff0000) -#else -#define ADDR(off,reg) \ - tst off, $0x80000000 ;\ - movne reg, $IO_BASE ;\ - moveq reg, $(PCIO_BASE & 0xff000000) ;\ - orreq reg, reg, $(PCIO_BASE & 0x00ff0000) +#if defined(__APCS_32__) +#define LOADREGS(t,r,l...) ldm##t r, l +#elif defined(__APCS_26__) +#define LOADREGS(t,r,l...) ldm##t r, l##^ #endif @ Purpose: transfer a block of data from the acorn scsi card to memory diff --git a/drivers/scsi/arm/acornscsi.c b/drivers/scsi/arm/acornscsi.c index 8e53f02cc31..918ccf81875 100644 --- a/drivers/scsi/arm/acornscsi.c +++ b/drivers/scsi/arm/acornscsi.c @@ -123,12 +123,6 @@ #define DBG(cmd,xxx...) xxx #endif -#ifndef STRINGIFY -#define STRINGIFY(x) #x -#endif -#define STRx(x) STRINGIFY(x) -#define NO_WRITE_STR STRx(NO_WRITE) - #include <linux/module.h> #include <linux/kernel.h> #include <linux/string.h> @@ -141,9 +135,10 @@ #include <linux/interrupt.h> #include <linux/init.h> #include <linux/bitops.h> +#include <linux/stringify.h> +#include <linux/io.h> #include <asm/system.h> -#include <asm/io.h> #include <asm/ecard.h> #include "../scsi.h" @@ -203,44 +198,46 @@ static void acornscsi_abortcmd(AS_Host *host, unsigned char tag); * Miscellaneous */ -static inline void -sbic_arm_write(unsigned int io_port, int reg, int value) +/* Offsets from MEMC base */ +#define SBIC_REGIDX 0x2000 +#define SBIC_REGVAL 0x2004 +#define DMAC_OFFSET 0x3000 + +/* Offsets from FAST IOC base */ +#define INT_REG 0x2000 +#define PAGE_REG 0x3000 + +static inline void sbic_arm_write(AS_Host *host, unsigned int reg, unsigned int value) { - __raw_writeb(reg, io_port); - __raw_writeb(value, io_port + 4); + writeb(reg, host->base + SBIC_REGIDX); + writeb(value, host->base + SBIC_REGVAL); } -#define sbic_arm_writenext(io,val) \ - __raw_writeb((val), (io) + 4) - -static inline -int sbic_arm_read(unsigned int io_port, int reg) +static inline int sbic_arm_read(AS_Host *host, unsigned int reg) { if(reg == SBIC_ASR) - return __raw_readl(io_port) & 255; - __raw_writeb(reg, io_port); - return __raw_readl(io_port + 4) & 255; + return readl(host->base + SBIC_REGIDX) & 255; + writeb(reg, host->base + SBIC_REGIDX); + return readl(host->base + SBIC_REGVAL) & 255; } -#define sbic_arm_readnext(io) \ - __raw_readb((io) + 4) +#define sbic_arm_writenext(host, val) writeb((val), (host)->base + SBIC_REGVAL) +#define sbic_arm_readnext(host) readb((host)->base + SBIC_REGVAL) #ifdef USE_DMAC -#define dmac_read(io_port,reg) \ - inb((io_port) + (reg)) +#define dmac_read(host,reg) \ + readb((host)->base + DMAC_OFFSET + ((reg) << 2)) -#define dmac_write(io_port,reg,value) \ - ({ outb((value), (io_port) + (reg)); }) +#define dmac_write(host,reg,value) \ + ({ writeb((value), (host)->base + DMAC_OFFSET + ((reg) << 2)); }) -#define dmac_clearintr(io_port) \ - ({ outb(0, (io_port)); }) +#define dmac_clearintr(host) writeb(0, (host)->fast + INT_REG) -static inline -unsigned int dmac_address(unsigned int io_port) +static inline unsigned int dmac_address(AS_Host *host) { - return dmac_read(io_port, DMAC_TXADRHI) << 16 | - dmac_read(io_port, DMAC_TXADRMD) << 8 | - dmac_read(io_port, DMAC_TXADRLO); + return dmac_read(host, DMAC_TXADRHI) << 16 | + dmac_read(host, DMAC_TXADRMD) << 8 | + dmac_read(host, DMAC_TXADRLO); } static @@ -248,15 +245,15 @@ void acornscsi_dumpdma(AS_Host *host, char *where) { unsigned int mode, addr, len; - mode = dmac_read(host->dma.io_port, DMAC_MODECON); - addr = dmac_address(host->dma.io_port); - len = dmac_read(host->dma.io_port, DMAC_TXCNTHI) << 8 | - dmac_read(host->dma.io_port, DMAC_TXCNTLO); + mode = dmac_read(host, DMAC_MODECON); + addr = dmac_address(host); + len = dmac_read(host, DMAC_TXCNTHI) << 8 | + dmac_read(host, DMAC_TXCNTLO); printk("scsi%d: %s: DMAC %02x @%06x+%04x msk %02x, ", host->host->host_no, where, mode, addr, (len + 1) & 0xffff, - dmac_read(host->dma.io_port, DMAC_MASKREG)); + dmac_read(host, DMAC_MASKREG)); printk("DMA @%06x, ", host->dma.start_addr); printk("BH @%p +%04x, ", host->scsi.SCp.ptr, @@ -272,9 +269,9 @@ unsigned long acornscsi_sbic_xfcount(AS_Host *host) { unsigned long length; - length = sbic_arm_read(host->scsi.io_port, SBIC_TRANSCNTH) << 16; - length |= sbic_arm_readnext(host->scsi.io_port) << 8; - length |= sbic_arm_readnext(host->scsi.io_port); + length = sbic_arm_read(host, SBIC_TRANSCNTH) << 16; + length |= sbic_arm_readnext(host) << 8; + length |= sbic_arm_readnext(host); return length; } @@ -285,7 +282,7 @@ acornscsi_sbic_wait(AS_Host *host, int stat_mask, int stat, int timeout, char *m int asr; do { - asr = sbic_arm_read(host->scsi.io_port, SBIC_ASR); + asr = sbic_arm_read(host, SBIC_ASR); if ((asr & stat_mask) == stat) return 0; @@ -304,7 +301,7 @@ int acornscsi_sbic_issuecmd(AS_Host *host, int command) if (acornscsi_sbic_wait(host, ASR_CIP, 0, 1000, "issuing command")) return -1; - sbic_arm_write(host->scsi.io_port, SBIC_CMND, command); + sbic_arm_write(host, SBIC_CMND, command); return 0; } @@ -331,20 +328,20 @@ void acornscsi_resetcard(AS_Host *host) /* assert reset line */ host->card.page_reg = 0x80; - outb(host->card.page_reg, host->card.io_page); + writeb(host->card.page_reg, host->fast + PAGE_REG); /* wait 3 cs. SCSI standard says 25ms. */ acornscsi_csdelay(3); host->card.page_reg = 0; - outb(host->card.page_reg, host->card.io_page); + writeb(host->card.page_reg, host->fast + PAGE_REG); /* * Should get a reset from the card */ timeout = 1000; do { - if (inb(host->card.io_intr) & 8) + if (readb(host->fast + INT_REG) & 8) break; udelay(1); } while (--timeout); @@ -353,19 +350,19 @@ void acornscsi_resetcard(AS_Host *host) printk("scsi%d: timeout while resetting card\n", host->host->host_no); - sbic_arm_read(host->scsi.io_port, SBIC_ASR); - sbic_arm_read(host->scsi.io_port, SBIC_SSR); + sbic_arm_read(host, SBIC_ASR); + sbic_arm_read(host, SBIC_SSR); /* setup sbic - WD33C93A */ - sbic_arm_write(host->scsi.io_port, SBIC_OWNID, OWNID_EAF | host->host->this_id); - sbic_arm_write(host->scsi.io_port, SBIC_CMND, CMND_RESET); + sbic_arm_write(host, SBIC_OWNID, OWNID_EAF | host->host->this_id); + sbic_arm_write(host, SBIC_CMND, CMND_RESET); /* * Command should cause a reset interrupt */ timeout = 1000; do { - if (inb(host->card.io_intr) & 8) + if (readb(host->fast + INT_REG) & 8) break; udelay(1); } while (--timeout); @@ -374,26 +371,26 @@ void acornscsi_resetcard(AS_Host *host) printk("scsi%d: timeout while resetting card\n", host->host->host_no); - sbic_arm_read(host->scsi.io_port, SBIC_ASR); - if (sbic_arm_read(host->scsi.io_port, SBIC_SSR) != 0x01) + sbic_arm_read(host, SBIC_ASR); + if (sbic_arm_read(host, SBIC_SSR) != 0x01) printk(KERN_CRIT "scsi%d: WD33C93A didn't give enhanced reset interrupt\n", host->host->host_no); - sbic_arm_write(host->scsi.io_port, SBIC_CTRL, INIT_SBICDMA | CTRL_IDI); - sbic_arm_write(host->scsi.io_port, SBIC_TIMEOUT, TIMEOUT_TIME); - sbic_arm_write(host->scsi.io_port, SBIC_SYNCHTRANSFER, SYNCHTRANSFER_2DBA); - sbic_arm_write(host->scsi.io_port, SBIC_SOURCEID, SOURCEID_ER | SOURCEID_DSP); + sbic_arm_write(host, SBIC_CTRL, INIT_SBICDMA | CTRL_IDI); + sbic_arm_write(host, SBIC_TIMEOUT, TIMEOUT_TIME); + sbic_arm_write(host, SBIC_SYNCHTRANSFER, SYNCHTRANSFER_2DBA); + sbic_arm_write(host, SBIC_SOURCEID, SOURCEID_ER | SOURCEID_DSP); host->card.page_reg = 0x40; - outb(host->card.page_reg, host->card.io_page); + writeb(host->card.page_reg, host->fast + PAGE_REG); /* setup dmac - uPC71071 */ - dmac_write(host->dma.io_port, DMAC_INIT, 0); + dmac_write(host, DMAC_INIT, 0); #ifdef USE_DMAC - dmac_write(host->dma.io_port, DMAC_INIT, INIT_8BIT); - dmac_write(host->dma.io_port, DMAC_CHANNEL, CHANNEL_0); - dmac_write(host->dma.io_port, DMAC_DEVCON0, INIT_DEVCON0); - dmac_write(host->dma.io_port, DMAC_DEVCON1, INIT_DEVCON1); + dmac_write(host, DMAC_INIT, INIT_8BIT); + dmac_write(host, DMAC_CHANNEL, CHANNEL_0); + dmac_write(host, DMAC_DEVCON0, INIT_DEVCON0); + dmac_write(host, DMAC_DEVCON1, INIT_DEVCON1); #endif host->SCpnt = NULL; @@ -741,9 +738,9 @@ intr_ret_t acornscsi_kick(AS_Host *host) * If we have an interrupt pending, then we may have been reselected. * In this case, we don't want to write to the registers */ - if (!(sbic_arm_read(host->scsi.io_port, SBIC_ASR) & (ASR_INT|ASR_BSY|ASR_CIP))) { - sbic_arm_write(host->scsi.io_port, SBIC_DESTID, SCpnt->device->id); - sbic_arm_write(host->scsi.io_port, SBIC_CMND, CMND_SELWITHATN); + if (!(sbic_arm_read(host, SBIC_ASR) & (ASR_INT|ASR_BSY|ASR_CIP))) { + sbic_arm_write(host, SBIC_DESTID, SCpnt->device->id); + sbic_arm_write(host, SBIC_CMND, CMND_SELWITHATN); } /* @@ -807,7 +804,7 @@ static void acornscsi_done(AS_Host *host, struct scsi_cmnd **SCpntp, struct scsi_cmnd *SCpnt = *SCpntp; /* clean up */ - sbic_arm_write(host->scsi.io_port, SBIC_SOURCEID, SOURCEID_ER | SOURCEID_DSP); + sbic_arm_write(host, SBIC_SOURCEID, SOURCEID_ER | SOURCEID_DSP); host->stats.fins += 1; @@ -918,13 +915,13 @@ static void acornscsi_data_read(AS_Host *host, char *ptr, unsigned int start_addr, unsigned int length) { - extern void __acornscsi_in(int port, char *buf, int len); + extern void __acornscsi_in(void __iomem *, char *buf, int len); unsigned int page, offset, len = length; page = (start_addr >> 12); offset = start_addr & ((1 << 12) - 1); - outb((page & 0x3f) | host->card.page_reg, host->card.io_page); + writeb((page & 0x3f) | host->card.page_reg, host->fast + PAGE_REG); while (len > 0) { unsigned int this_len; @@ -934,7 +931,7 @@ void acornscsi_data_read(AS_Host *host, char *ptr, else this_len = len; - __acornscsi_in(host->card.io_ram + (offset << 1), ptr, this_len); + __acornscsi_in(host->base + (offset << 1), ptr, this_len); offset += this_len; ptr += this_len; @@ -943,10 +940,10 @@ void acornscsi_data_read(AS_Host *host, char *ptr, if (offset == (1 << 12)) { offset = 0; page ++; - outb((page & 0x3f) | host->card.page_reg, host->card.io_page); + writeb((page & 0x3f) | host->card.page_reg, host->fast + PAGE_REG); } } - outb(host->card.page_reg, host->card.io_page); + writeb(host->card.page_reg, host->fast + PAGE_REG); } /* @@ -963,13 +960,13 @@ static void acornscsi_data_write(AS_Host *host, char *ptr, unsigned int start_addr, unsigned int length) { - extern void __acornscsi_out(int port, char *buf, int len); + extern void __acornscsi_out(void __iomem *, char *buf, int len); unsigned int page, offset, len = length; page = (start_addr >> 12); offset = start_addr & ((1 << 12) - 1); - outb((page & 0x3f) | host->card.page_reg, host->card.io_page); + writeb((page & 0x3f) | host->card.page_reg, host->fast + PAGE_REG); while (len > 0) { unsigned int this_len; @@ -979,7 +976,7 @@ void acornscsi_data_write(AS_Host *host, char *ptr, else this_len = len; - __acornscsi_out(host->card.io_ram + (offset << 1), ptr, this_len); + __acornscsi_out(host->base + (offset << 1), ptr, this_len); offset += this_len; ptr += this_len; @@ -988,10 +985,10 @@ void acornscsi_data_write(AS_Host *host, char *ptr, if (offset == (1 << 12)) { offset = 0; page ++; - outb((page & 0x3f) | host->card.page_reg, host->card.io_page); + writeb((page & 0x3f) | host->card.page_reg, host->fast + PAGE_REG); } } - outb(host->card.page_reg, host->card.io_page); + writeb(host->card.page_reg, host->fast + PAGE_REG); } /* ========================================================================================= @@ -1008,8 +1005,8 @@ void acornscsi_data_write(AS_Host *host, char *ptr, static inline void acornscsi_dma_stop(AS_Host *host) { - dmac_write(host->dma.io_port, DMAC_MASKREG, MASK_ON); - dmac_clearintr(host->dma.io_intr_clear); + dmac_write(host, DMAC_MASKREG, MASK_ON); + dmac_clearintr(host); #if (DEBUG & DEBUG_DMA) DBG(host->SCpnt, acornscsi_dumpdma(host, "stop")); @@ -1031,7 +1028,7 @@ void acornscsi_dma_setup(AS_Host *host, dmadir_t direction) host->dma.direction = direction; - dmac_write(host->dma.io_port, DMAC_MASKREG, MASK_ON); + dmac_write(host, DMAC_MASKREG, MASK_ON); if (direction == DMA_OUT) { #if (DEBUG & DEBUG_NO_WRITE) @@ -1062,13 +1059,13 @@ void acornscsi_dma_setup(AS_Host *host, dmadir_t direction) length); length -= 1; - dmac_write(host->dma.io_port, DMAC_TXCNTLO, length); - dmac_write(host->dma.io_port, DMAC_TXCNTHI, length >> 8); - dmac_write(host->dma.io_port, DMAC_TXADRLO, address); - dmac_write(host->dma.io_port, DMAC_TXADRMD, address >> 8); - dmac_write(host->dma.io_port, DMAC_TXADRHI, 0); - dmac_write(host->dma.io_port, DMAC_MODECON, mode); - dmac_write(host->dma.io_port, DMAC_MASKREG, MASK_OFF); + dmac_write(host, DMAC_TXCNTLO, length); + dmac_write(host, DMAC_TXCNTHI, length >> 8); + dmac_write(host, DMAC_TXADRLO, address); + dmac_write(host, DMAC_TXADRMD, address >> 8); + dmac_write(host, DMAC_TXADRHI, 0); + dmac_write(host, DMAC_MODECON, mode); + dmac_write(host, DMAC_MASKREG, MASK_OFF); #if (DEBUG & DEBUG_DMA) DBG(host->SCpnt, acornscsi_dumpdma(host, "strt")); @@ -1088,8 +1085,8 @@ void acornscsi_dma_setup(AS_Host *host, dmadir_t direction) static void acornscsi_dma_cleanup(AS_Host *host) { - dmac_write(host->dma.io_port, DMAC_MASKREG, MASK_ON); - dmac_clearintr(host->dma.io_intr_clear); + dmac_write(host, DMAC_MASKREG, MASK_ON); + dmac_clearintr(host); /* * Check for a pending transfer @@ -1116,7 +1113,7 @@ void acornscsi_dma_cleanup(AS_Host *host) /* * Calculate number of bytes transferred from DMA. */ - transferred = dmac_address(host->dma.io_port) - host->dma.start_addr; + transferred = dmac_address(host) - host->dma.start_addr; host->dma.transferred += transferred; if (host->dma.direction == DMA_IN) @@ -1152,13 +1149,13 @@ void acornscsi_dma_intr(AS_Host *host) DBG(host->SCpnt, acornscsi_dumpdma(host, "inti")); #endif - dmac_write(host->dma.io_port, DMAC_MASKREG, MASK_ON); - dmac_clearintr(host->dma.io_intr_clear); + dmac_write(host, DMAC_MASKREG, MASK_ON); + dmac_clearintr(host); /* * Calculate amount transferred via DMA */ - transferred = dmac_address(host->dma.io_port) - host->dma.start_addr; + transferred = dmac_address(host) - host->dma.start_addr; host->dma.transferred += transferred; /* @@ -1190,12 +1187,12 @@ void acornscsi_dma_intr(AS_Host *host) length); length -= 1; - dmac_write(host->dma.io_port, DMAC_TXCNTLO, length); - dmac_write(host->dma.io_port, DMAC_TXCNTHI, length >> 8); - dmac_write(host->dma.io_port, DMAC_TXADRLO, address); - dmac_write(host->dma.io_port, DMAC_TXADRMD, address >> 8); - dmac_write(host->dma.io_port, DMAC_TXADRHI, 0); - dmac_write(host->dma.io_port, DMAC_MASKREG, MASK_OFF); + dmac_write(host, DMAC_TXCNTLO, length); + dmac_write(host, DMAC_TXCNTHI, length >> 8); + dmac_write(host, DMAC_TXADRLO, address); + dmac_write(host, DMAC_TXADRMD, address >> 8); + dmac_write(host, DMAC_TXADRHI, 0); + dmac_write(host, DMAC_MASKREG, MASK_OFF); #if (DEBUG & DEBUG_DMA) DBG(host->SCpnt, acornscsi_dumpdma(host, "into")); @@ -1209,15 +1206,15 @@ void acornscsi_dma_intr(AS_Host *host) * attention condition. We continue giving one byte until * the device recognises the attention. */ - if (dmac_read(host->dma.io_port, DMAC_STATUS) & STATUS_RQ0) { + if (dmac_read(host, DMAC_STATUS) & STATUS_RQ0) { acornscsi_abortcmd(host, host->SCpnt->tag); - dmac_write(host->dma.io_port, DMAC_TXCNTLO, 0); - dmac_write(host->dma.io_port, DMAC_TXCNTHI, 0); - dmac_write(host->dma.io_port, DMAC_TXADRLO, 0); - dmac_write(host->dma.io_port, DMAC_TXADRMD, 0); - dmac_write(host->dma.io_port, DMAC_TXADRHI, 0); - dmac_write(host->dma.io_port, DMAC_MASKREG, MASK_OFF); + dmac_write(host, DMAC_TXCNTLO, 0); + dmac_write(host, DMAC_TXCNTHI, 0); + dmac_write(host, DMAC_TXADRLO, 0); + dmac_write(host, DMAC_TXADRMD, 0); + dmac_write(host, DMAC_TXADRHI, 0); + dmac_write(host, DMAC_MASKREG, MASK_OFF); } #endif } @@ -1271,9 +1268,9 @@ void acornscsi_dma_adjust(AS_Host *host) host->dma.xfer_setup = 0; else { transferred += host->dma.start_addr; - dmac_write(host->dma.io_port, DMAC_TXADRLO, transferred); - dmac_write(host->dma.io_port, DMAC_TXADRMD, transferred >> 8); - dmac_write(host->dma.io_port, DMAC_TXADRHI, transferred >> 16); + dmac_write(host, DMAC_TXADRLO, transferred); + dmac_write(host, DMAC_TXADRMD, transferred >> 8); + dmac_write(host, DMAC_TXADRHI, transferred >> 16); #if (DEBUG & (DEBUG_DMA|DEBUG_WRITE)) DBG(host->SCpnt, acornscsi_dumpdma(host, "adjo")); #endif @@ -1292,12 +1289,12 @@ acornscsi_write_pio(AS_Host *host, char *bytes, int *ptr, int len, unsigned int int my_ptr = *ptr; while (my_ptr < len) { - asr = sbic_arm_read(host->scsi.io_port, SBIC_ASR); + asr = sbic_arm_read(host, SBIC_ASR); if (asr & ASR_DBR) { timeout = max_timeout; - sbic_arm_write(host->scsi.io_port, SBIC_DATA, bytes[my_ptr++]); + sbic_arm_write(host, SBIC_DATA, bytes[my_ptr++]); } else if (asr & ASR_INT) break; else if (--timeout == 0) @@ -1320,9 +1317,9 @@ acornscsi_sendcommand(AS_Host *host) { struct scsi_cmnd *SCpnt = host->SCpnt; - sbic_arm_write(host->scsi.io_port, SBIC_TRANSCNTH, 0); - sbic_arm_writenext(host->scsi.io_port, 0); - sbic_arm_writenext(host->scsi.io_port, SCpnt->cmd_len - host->scsi.SCp.sent_command); + sbic_arm_write(host, SBIC_TRANSCNTH, 0); + sbic_arm_writenext(host, 0); + sbic_arm_writenext(host, SCpnt->cmd_len - host->scsi.SCp.sent_command); acornscsi_sbic_issuecmd(host, CMND_XFERINFO); @@ -1351,7 +1348,7 @@ void acornscsi_sendmessage(AS_Host *host) acornscsi_sbic_wait(host, ASR_DBR, ASR_DBR, 1000, "sending message 1"); - sbic_arm_write(host->scsi.io_port, SBIC_DATA, NOP); + sbic_arm_write(host, SBIC_DATA, NOP); host->scsi.last_message = NOP; #if (DEBUG & DEBUG_MESSAGES) @@ -1365,7 +1362,7 @@ void acornscsi_sendmessage(AS_Host *host) acornscsi_sbic_wait(host, ASR_DBR, ASR_DBR, 1000, "sending message 2"); - sbic_arm_write(host->scsi.io_port, SBIC_DATA, msg->msg[0]); + sbic_arm_write(host, SBIC_DATA, msg->msg[0]); host->scsi.last_message = msg->msg[0]; #if (DEBUG & DEBUG_MESSAGES) @@ -1382,9 +1379,9 @@ void acornscsi_sendmessage(AS_Host *host) * initiator. This provides an interlock so that the * initiator can determine which message byte is rejected. */ - sbic_arm_write(host->scsi.io_port, SBIC_TRANSCNTH, 0); - sbic_arm_writenext(host->scsi.io_port, 0); - sbic_arm_writenext(host->scsi.io_port, message_length); + sbic_arm_write(host, SBIC_TRANSCNTH, 0); + sbic_arm_writenext(host, 0); + sbic_arm_writenext(host, message_length); acornscsi_sbic_issuecmd(host, CMND_XFERINFO); msgnr = 0; @@ -1421,7 +1418,7 @@ void acornscsi_readstatusbyte(AS_Host *host) { acornscsi_sbic_issuecmd(host, CMND_XFERINFO|CMND_SBT); acornscsi_sbic_wait(host, ASR_DBR, ASR_DBR, 1000, "reading status byte"); - host->scsi.SCp.Status = sbic_arm_read(host->scsi.io_port, SBIC_DATA); + host->scsi.SCp.Status = sbic_arm_read(host, SBIC_DATA); } /* @@ -1438,12 +1435,12 @@ unsigned char acornscsi_readmessagebyte(AS_Host *host) acornscsi_sbic_wait(host, ASR_DBR, ASR_DBR, 1000, "for message byte"); - message = sbic_arm_read(host->scsi.io_port, SBIC_DATA); + message = sbic_arm_read(host, SBIC_DATA); /* wait for MSGIN-XFER-PAUSED */ acornscsi_sbic_wait(host, ASR_INT, ASR_INT, 1000, "for interrupt after message byte"); - sbic_arm_read(host->scsi.io_port, SBIC_SSR); + sbic_arm_read(host, SBIC_SSR); return message; } @@ -1480,7 +1477,7 @@ void acornscsi_message(AS_Host *host) /* wait for next msg-in */ acornscsi_sbic_wait(host, ASR_INT, ASR_INT, 1000, "for interrupt after negate ack"); - sbic_arm_read(host->scsi.io_port, SBIC_SSR); + sbic_arm_read(host, SBIC_SSR); } } while (msgidx < msglen); @@ -1602,7 +1599,7 @@ void acornscsi_message(AS_Host *host) host->host->host_no, acornscsi_target(host)); host->device[host->SCpnt->device->id].sync_xfer = SYNCHTRANSFER_2DBA; host->device[host->SCpnt->device->id].sync_state = SYNC_ASYNCHRONOUS; - sbic_arm_write(host->scsi.io_port, SBIC_SYNCHTRANSFER, host->device[host->SCpnt->device->id].sync_xfer); + sbic_arm_write(host, SBIC_SYNCHTRANSFER, host->device[host->SCpnt->device->id].sync_xfer); break; default: @@ -1652,7 +1649,7 @@ void acornscsi_message(AS_Host *host) host->device[host->SCpnt->device->id].sync_xfer = calc_sync_xfer(period * 4, length); } - sbic_arm_write(host->scsi.io_port, SBIC_SYNCHTRANSFER, host->device[host->SCpnt->device->id].sync_xfer); + sbic_arm_write(host, SBIC_SYNCHTRANSFER, host->device[host->SCpnt->device->id].sync_xfer); break; #else /* We do not accept synchronous transfers. Respond with a @@ -1792,10 +1789,10 @@ int acornscsi_starttransfer(AS_Host *host) residual = scsi_bufflen(host->SCpnt) - host->scsi.SCp.scsi_xferred; - sbic_arm_write(host->scsi.io_port, SBIC_SYNCHTRANSFER, host->device[host->SCpnt->device->id].sync_xfer); - sbic_arm_writenext(host->scsi.io_port, residual >> 16); - sbic_arm_writenext(host->scsi.io_port, residual >> 8); - sbic_arm_writenext(host->scsi.io_port, residual); + sbic_arm_write(host, SBIC_SYNCHTRANSFER, host->device[host->SCpnt->device->id].sync_xfer); + sbic_arm_writenext(host, residual >> 16); + sbic_arm_writenext(host, residual >> 8); + sbic_arm_writenext(host, residual); acornscsi_sbic_issuecmd(host, CMND_XFERINFO); return 1; } @@ -1816,7 +1813,7 @@ int acornscsi_reconnect(AS_Host *host) { unsigned int target, lun, ok = 0; - target = sbic_arm_read(host->scsi.io_port, SBIC_SOURCEID); + target = sbic_arm_read(host, SBIC_SOURCEID); if (!(target & 8)) printk(KERN_ERR "scsi%d: invalid source id after reselection " @@ -1832,7 +1829,7 @@ int acornscsi_reconnect(AS_Host *host) host->SCpnt = NULL; } - lun = sbic_arm_read(host->scsi.io_port, SBIC_DATA) & 7; + lun = sbic_arm_read(host, SBIC_DATA) & 7; host->scsi.reconnected.target = target; host->scsi.reconnected.lun = lun; @@ -1952,7 +1949,7 @@ static void acornscsi_abortcmd(AS_Host *host, unsigned char tag) { host->scsi.phase = PHASE_ABORTED; - sbic_arm_write(host->scsi.io_port, SBIC_CMND, CMND_ASSERTATN); + sbic_arm_write(host, SBIC_CMND, CMND_ASSERTATN); msgqueue_flush(&host->scsi.msgs); #ifdef CONFIG_SCSI_ACORNSCSI_TAGGED_QUEUE @@ -1979,11 +1976,11 @@ intr_ret_t acornscsi_sbicintr(AS_Host *host, int in_irq) { unsigned int asr, ssr; - asr = sbic_arm_read(host->scsi.io_port, SBIC_ASR); + asr = sbic_arm_read(host, SBIC_ASR); if (!(asr & ASR_INT)) return INTR_IDLE; - ssr = sbic_arm_read(host->scsi.io_port, SBIC_SSR); + ssr = sbic_arm_read(host, SBIC_SSR); #if (DEBUG & DEBUG_PHASES) print_sbic_status(asr, ssr, host->scsi.phase); @@ -1999,15 +1996,15 @@ intr_ret_t acornscsi_sbicintr(AS_Host *host, int in_irq) printk(KERN_ERR "scsi%d: reset in standard mode but wanted advanced mode.\n", host->host->host_no); /* setup sbic - WD33C93A */ - sbic_arm_write(host->scsi.io_port, SBIC_OWNID, OWNID_EAF | host->host->this_id); - sbic_arm_write(host->scsi.io_port, SBIC_CMND, CMND_RESET); + sbic_arm_write(host, SBIC_OWNID, OWNID_EAF | host->host->this_id); + sbic_arm_write(host, SBIC_CMND, CMND_RESET); return INTR_IDLE; case 0x01: /* reset state - advanced */ - sbic_arm_write(host->scsi.io_port, SBIC_CTRL, INIT_SBICDMA | CTRL_IDI); - sbic_arm_write(host->scsi.io_port, SBIC_TIMEOUT, TIMEOUT_TIME); - sbic_arm_write(host->scsi.io_port, SBIC_SYNCHTRANSFER, SYNCHTRANSFER_2DBA); - sbic_arm_write(host->scsi.io_port, SBIC_SOURCEID, SOURCEID_ER | SOURCEID_DSP); + sbic_arm_write(host, SBIC_CTRL, INIT_SBICDMA | CTRL_IDI); + sbic_arm_write(host, SBIC_TIMEOUT, TIMEOUT_TIME); + sbic_arm_write(host, SBIC_SYNCHTRANSFER, SYNCHTRANSFER_2DBA); + sbic_arm_write(host, SBIC_SOURCEID, SOURCEID_ER | SOURCEID_DSP); msgqueue_flush(&host->scsi.msgs); return INTR_IDLE; @@ -2025,10 +2022,10 @@ intr_ret_t acornscsi_sbicintr(AS_Host *host, int in_irq) msgqueue_flush(&host->scsi.msgs); host->dma.transferred = host->scsi.SCp.scsi_xferred; /* 33C93 gives next interrupt indicating bus phase */ - asr = sbic_arm_read(host->scsi.io_port, SBIC_ASR); + asr = sbic_arm_read(host, SBIC_ASR); if (!(asr & ASR_INT)) break; - ssr = sbic_arm_read(host->scsi.io_port, SBIC_SSR); + ssr = sbic_arm_read(host, SBIC_SSR); ADD_STATUS(8, ssr, host->scsi.phase, 1); ADD_STATUS(host->SCpnt->device->id, ssr, host->scsi.phase, 1); goto connected; @@ -2476,11 +2473,11 @@ acornscsi_intr(int irq, void *dev_id) do { ret = INTR_IDLE; - iostatus = inb(host->card.io_intr); + iostatus = readb(host->fast + INT_REG); if (iostatus & 2) { acornscsi_dma_intr(host); - iostatus = inb(host->card.io_intr); + iostatus = readb(host->fast + INT_REG); } if (iostatus & 8) @@ -2655,7 +2652,7 @@ static enum res_abort acornscsi_do_abort(AS_Host *host, struct scsi_cmnd *SCpnt) * busylun bit. */ case PHASE_CONNECTED: - sbic_arm_write(host->scsi.io_port, SBIC_CMND, CMND_DISCONNECT); + sbic_arm_write(host, SBIC_CMND, CMND_DISCONNECT); host->SCpnt = NULL; res = res_success_clear; break; @@ -2699,8 +2696,8 @@ int acornscsi_abort(struct scsi_cmnd *SCpnt) #if (DEBUG & DEBUG_ABORT) { int asr, ssr; - asr = sbic_arm_read(host->scsi.io_port, SBIC_ASR); - ssr = sbic_arm_read(host->scsi.io_port, SBIC_SSR); + asr = sbic_arm_read(host, SBIC_ASR); + ssr = sbic_arm_read(host, SBIC_SSR); printk(KERN_WARNING "acornscsi_abort: "); print_sbic_status(asr, ssr, host->scsi.phase); @@ -2731,9 +2728,7 @@ int acornscsi_abort(struct scsi_cmnd *SCpnt) //#if (DEBUG & DEBUG_ABORT) printk("success\n"); //#endif - SCpnt->result = DID_ABORT << 16; - SCpnt->scsi_done(SCpnt); - result = SCSI_ABORT_SUCCESS; + result = SUCCESS; break; /* @@ -2745,7 +2740,7 @@ int acornscsi_abort(struct scsi_cmnd *SCpnt) //#if (DEBUG & DEBUG_ABORT) printk("snooze\n"); //#endif - result = SCSI_ABORT_SNOOZE; + result = FAILED; break; /* @@ -2755,11 +2750,7 @@ int acornscsi_abort(struct scsi_cmnd *SCpnt) default: case res_not_running: acornscsi_dumplog(host, SCpnt->device->id); -#if (DEBUG & DEBUG_ABORT) - result = SCSI_ABORT_SNOOZE; -#else - result = SCSI_ABORT_NOT_RUNNING; -#endif + result = FAILED; //#if (DEBUG & DEBUG_ABORT) printk("not running\n"); //#endif @@ -2770,13 +2761,12 @@ int acornscsi_abort(struct scsi_cmnd *SCpnt) } /* - * Prototype: int acornscsi_reset(struct scsi_cmnd *SCpnt, unsigned int reset_flags) + * Prototype: int acornscsi_reset(struct scsi_cmnd *SCpnt) * Purpose : reset a command on this host/reset this host * Params : SCpnt - command causing reset - * result - what type of reset to perform * Returns : one of SCSI_RESET_ macros */ -int acornscsi_reset(struct scsi_cmnd *SCpnt, unsigned int reset_flags) +int acornscsi_bus_reset(struct scsi_cmnd *SCpnt) { AS_Host *host = (AS_Host *)SCpnt->device->host->hostdata; struct scsi_cmnd *SCptr; @@ -2787,8 +2777,8 @@ int acornscsi_reset(struct scsi_cmnd *SCpnt, unsigned int reset_flags) { int asr, ssr; - asr = sbic_arm_read(host->scsi.io_port, SBIC_ASR); - ssr = sbic_arm_read(host->scsi.io_port, SBIC_SSR); + asr = sbic_arm_read(host, SBIC_ASR); + ssr = sbic_arm_read(host, SBIC_SSR); printk(KERN_WARNING "acornscsi_reset: "); print_sbic_status(asr, ssr, host->scsi.phase); @@ -2798,28 +2788,16 @@ int acornscsi_reset(struct scsi_cmnd *SCpnt, unsigned int reset_flags) acornscsi_dma_stop(host); - SCptr = host->SCpnt; - /* * do hard reset. This resets all devices on this host, and so we * must set the reset status on all commands. */ acornscsi_resetcard(host); - /* - * report reset on commands current connected/disconnected - */ - acornscsi_reportstatus(&host->SCpnt, &SCptr, DID_RESET); - while ((SCptr = queue_remove(&host->queues.disconnected)) != NULL) - acornscsi_reportstatus(&SCptr, &SCpnt, DID_RESET); - - if (SCpnt) { - SCpnt->result = DID_RESET << 16; - SCpnt->scsi_done(SCpnt); - } + ; - return SCSI_RESET_BUS_RESET | SCSI_RESET_HOST_RESET | SCSI_RESET_SUCCESS; + return SUCCESS; } /*============================================================================================== @@ -2850,7 +2828,7 @@ char *acornscsi_info(struct Scsi_Host *host) " LINK" #endif #if (DEBUG & DEBUG_NO_WRITE) - " NOWRITE ("NO_WRITE_STR")" + " NOWRITE (" __stringify(NO_WRITE) ")" #endif , host->hostt->name, host->io_port, host->irq, VER_MAJOR, VER_MINOR, VER_PATCH); @@ -2881,15 +2859,15 @@ int acornscsi_proc_info(struct Scsi_Host *instance, char *buffer, char **start, " LINK" #endif #if (DEBUG & DEBUG_NO_WRITE) - " NOWRITE ("NO_WRITE_STR")" + " NOWRITE (" __stringify(NO_WRITE) ")" #endif "\n\n", VER_MAJOR, VER_MINOR, VER_PATCH); - p += sprintf(p, "SBIC: WD33C93A Address: %08X IRQ : %d\n", - host->scsi.io_port, host->scsi.irq); + p += sprintf(p, "SBIC: WD33C93A Address: %p IRQ : %d\n", + host->base + SBIC_REGIDX, host->scsi.irq); #ifdef USE_DMAC - p += sprintf(p, "DMAC: uPC71071 Address: %08X IRQ : %d\n\n", - host->dma.io_port, host->scsi.irq); + p += sprintf(p, "DMAC: uPC71071 Address: %p IRQ : %d\n\n", + host->base + DMAC_OFFSET, host->scsi.irq); #endif p += sprintf(p, "Statistics:\n" @@ -2976,9 +2954,8 @@ static struct scsi_host_template acornscsi_template = { .name = "AcornSCSI", .info = acornscsi_info, .queuecommand = acornscsi_queuecmd, -#warning fixme - .abort = acornscsi_abort, - .reset = acornscsi_reset, + .eh_abort_handler = acornscsi_abort, + .eh_bus_reset_handler = acornscsi_bus_reset, .can_queue = 16, .this_id = 7, .sg_tablesize = SG_ALL, @@ -2992,48 +2969,37 @@ acornscsi_probe(struct expansion_card *ec, const struct ecard_id *id) { struct Scsi_Host *host; AS_Host *ashost; - int ret = -ENOMEM; + int ret; - host = scsi_host_alloc(&acornscsi_template, sizeof(AS_Host)); - if (!host) + ret = ecard_request_resources(ec); + if (ret) goto out; + host = scsi_host_alloc(&acornscsi_template, sizeof(AS_Host)); + if (!host) { + ret = -ENOMEM; + goto out_release; + } + ashost = (AS_Host *)host->hostdata; - host->io_port = ecard_address(ec, ECARD_MEMC, 0); - host->irq = ec->irq; + ashost->base = ecardm_iomap(ec, ECARD_RES_MEMC, 0, 0); + ashost->fast = ecardm_iomap(ec, ECARD_RES_IOCFAST, 0, 0); + if (!ashost->base || !ashost->fast) + goto out_put; - ashost->host = host; - ashost->scsi.io_port = ioaddr(host->io_port + 0x800); - ashost->scsi.irq = host->irq; - ashost->card.io_intr = POD_SPACE(host->io_port) + 0x800; - ashost->card.io_page = POD_SPACE(host->io_port) + 0xc00; - ashost->card.io_ram = ioaddr(host->io_port); - ashost->dma.io_port = host->io_port + 0xc00; - ashost->dma.io_intr_clear = POD_SPACE(host->io_port) + 0x800; + host->irq = ec->irq; + ashost->host = host; + ashost->scsi.irq = host->irq; - ec->irqaddr = (char *)ioaddr(ashost->card.io_intr); + ec->irqaddr = ashost->fast + INT_REG; ec->irqmask = 0x0a; - ret = -EBUSY; - if (!request_region(host->io_port + 0x800, 2, "acornscsi(sbic)")) - goto err_1; - if (!request_region(ashost->card.io_intr, 1, "acornscsi(intr)")) - goto err_2; - if (!request_region(ashost->card.io_page, 1, "acornscsi(page)")) - goto err_3; -#ifdef USE_DMAC - if (!request_region(ashost->dma.io_port, 256, "acornscsi(dmac)")) - goto err_4; -#endif - if (!request_region(host->io_port, 2048, "acornscsi(ram)")) - goto err_5; - ret = request_irq(host->irq, acornscsi_intr, IRQF_DISABLED, "acornscsi", ashost); if (ret) { printk(KERN_CRIT "scsi%d: IRQ%d not free: %d\n", host->host_no, ashost->scsi.irq, ret); - goto err_6; + goto out_put; } memset(&ashost->stats, 0, sizeof (ashost->stats)); @@ -3045,27 +3011,22 @@ acornscsi_probe(struct expansion_card *ec, const struct ecard_id *id) ret = scsi_add_host(host, &ec->dev); if (ret) - goto err_7; + goto out_irq; scsi_scan_host(host); goto out; - err_7: + out_irq: free_irq(host->irq, ashost); - err_6: - release_region(host->io_port, 2048); - err_5: -#ifdef USE_DMAC - release_region(ashost->dma.io_port, 256); -#endif - err_4: - release_region(ashost->card.io_page, 1); - err_3: - release_region(ashost->card.io_intr, 1); - err_2: - release_region(host->io_port + 0x800, 2); - err_1: + msgqueue_free(&ashost->scsi.msgs); + queue_free(&ashost->queues.disconnected); + queue_free(&ashost->queues.issue); + out_put: + ecardm_iounmap(ec, ashost->fast); + ecardm_iounmap(ec, ashost->base); scsi_host_put(host); + out_release: + ecard_release_resources(ec); out: return ret; } @@ -3081,20 +3042,17 @@ static void __devexit acornscsi_remove(struct expansion_card *ec) /* * Put card into RESET state */ - outb(0x80, ashost->card.io_page); + writeb(0x80, ashost->fast + PAGE_REG); free_irq(host->irq, ashost); - release_region(host->io_port + 0x800, 2); - release_region(ashost->card.io_intr, 1); - release_region(ashost->card.io_page, 1); - release_region(ashost->dma.io_port, 256); - release_region(host->io_port, 2048); - msgqueue_free(&ashost->scsi.msgs); queue_free(&ashost->queues.disconnected); queue_free(&ashost->queues.issue); + ecardm_iounmap(ec, ashost->fast); + ecardm_iounmap(ec, ashost->base); scsi_host_put(host); + ecard_release_resources(ec); } static const struct ecard_id acornscsi_cids[] = { diff --git a/drivers/scsi/arm/acornscsi.h b/drivers/scsi/arm/acornscsi.h index d11424b89f4..8d2172a0b35 100644 --- a/drivers/scsi/arm/acornscsi.h +++ b/drivers/scsi/arm/acornscsi.h @@ -179,7 +179,6 @@ /* miscellaneous internal variables */ -#define POD_SPACE(x) ((x) + 0xd0000) #define MASK_ON (MASKREG_M3|MASKREG_M2|MASKREG_M1|MASKREG_M0) #define MASK_OFF (MASKREG_M3|MASKREG_M2|MASKREG_M1) @@ -279,10 +278,11 @@ typedef struct acornscsi_hostdata { struct Scsi_Host *host; /* host */ struct scsi_cmnd *SCpnt; /* currently processing command */ struct scsi_cmnd *origSCpnt; /* original connecting command */ + void __iomem *base; /* memc base address */ + void __iomem *fast; /* fast ioc base address */ /* driver information */ struct { - unsigned int io_port; /* base address of WD33C93 */ unsigned int irq; /* interrupt */ phase_t phase; /* current phase */ @@ -329,8 +329,6 @@ typedef struct acornscsi_hostdata { /* DMA info */ struct { - unsigned int io_port; /* base address of DMA controller */ - unsigned int io_intr_clear; /* address of DMA interrupt clear */ unsigned int free_addr; /* next free address */ unsigned int start_addr; /* start address of current transfer */ dmadir_t direction; /* dma direction */ @@ -345,9 +343,6 @@ typedef struct acornscsi_hostdata { /* card info */ struct { - unsigned int io_intr; /* base address of interrupt id reg */ - unsigned int io_page; /* base address of page reg */ - unsigned int io_ram; /* base address of RAM access */ unsigned char page_reg; /* current setting of page reg */ } card; diff --git a/drivers/serial/Kconfig b/drivers/serial/Kconfig index 0843c540068..18ca9075e13 100644 --- a/drivers/serial/Kconfig +++ b/drivers/serial/Kconfig @@ -448,22 +448,27 @@ config SERIAL_CLPS711X_CONSOLE your boot loader (lilo or loadlin) about how to pass options to the kernel at boot time.) -config SERIAL_S3C2410 - tristate "Samsung S3C2410/S3C2440/S3C2442/S3C2412 Serial port support" - depends on ARM && ARCH_S3C2410 - select SERIAL_CORE +config SERIAL_SAMSUNG + tristate "Samsung SoC serial support" + depends on ARM && PLAT_S3C24XX help Support for the on-chip UARTs on the Samsung S3C24XX series CPUs, providing /dev/ttySAC0, 1 and 2 (note, some machines may not provide all of these ports, depending on how the serial port pins are configured. - Currently this driver supports the UARTS on the S3C2410, S3C2440, - S3C2442, S3C2412 and S3C2413 CPUs. +config SERIAL_SAMSUNG_DEBUG + bool "Samsung SoC serial debug" + depends on SERIAL_SAMSUNG + help + Add support for debugging the serial driver. Since this is + generally being used as a console, we use our own output + routines that go via the low-level debug printascii() + function. -config SERIAL_S3C2410_CONSOLE - bool "Support for console on S3C2410 serial port" - depends on SERIAL_S3C2410=y +config SERIAL_SAMSUNG_CONSOLE + bool "Support for console on Samsung SoC serial port" + depends on SERIAL_SAMSUNG=y select SERIAL_CORE_CONSOLE help Allow selection of the S3C24XX on-board serial ports for use as @@ -476,6 +481,37 @@ config SERIAL_S3C2410_CONSOLE your boot loader about how to pass options to the kernel at boot time.) +config SERIAL_S3C2400 + tristate "Samsung S3C2410 Serial port support" + depends on ARM && SERIAL_SAMSUNG && CPU_S3C2400 + default y if CPU_S3C2400 + help + Serial port support for the Samsung S3C2400 SoC + +config SERIAL_S3C2410 + tristate "Samsung S3C2410 Serial port support" + depends on SERIAL_SAMSUNG && CPU_S3C2410 + default y if CPU_S3C2410 + help + Serial port support for the Samsung S3C2410 SoC + +config SERIAL_S3C2412 + tristate "Samsung S3C2412/S3C2413 Serial port support" + depends on SERIAL_SAMSUNG && CPU_S3C2412 + default y if CPU_S3C2412 + help + Serial port support for the Samsung S3C2412 and S3C2413 SoC + +config SERIAL_S3C2440 + tristate "Samsung S3C2440/S3C2442 Serial port support" + depends on SERIAL_SAMSUNG && (CPU_S3C2440 || CPU_S3C2442) + default y if CPU_S3C2440 + default y if CPU_S3C2442 + help + Serial port support for the Samsung S3C2440 and S3C2442 SoC + + + config SERIAL_DZ bool "DECstation DZ serial driver" depends on MACH_DECSTATION && 32BIT diff --git a/drivers/serial/Makefile b/drivers/serial/Makefile index 0d9c09b1e83..7d85c1fbe7e 100644 --- a/drivers/serial/Makefile +++ b/drivers/serial/Makefile @@ -28,7 +28,11 @@ obj-$(CONFIG_SERIAL_PNX8XXX) += pnx8xxx_uart.o obj-$(CONFIG_SERIAL_SA1100) += sa1100.o obj-$(CONFIG_SERIAL_BFIN) += bfin_5xx.o obj-$(CONFIG_SERIAL_BFIN_SPORT) += bfin_sport_uart.o +obj-$(CONFIG_SERIAL_SAMSUNG) += samsung.o +obj-$(CONFIG_SERIAL_S3C2400) += s3c2400.o obj-$(CONFIG_SERIAL_S3C2410) += s3c2410.o +obj-$(CONFIG_SERIAL_S3C2412) += s3c2412.o +obj-$(CONFIG_SERIAL_S3C2440) += s3c2440.o obj-$(CONFIG_SERIAL_SUNCORE) += suncore.o obj-$(CONFIG_SERIAL_SUNHV) += sunhv.o obj-$(CONFIG_SERIAL_SUNZILOG) += sunzilog.o diff --git a/drivers/serial/s3c2400.c b/drivers/serial/s3c2400.c new file mode 100644 index 00000000000..a1102053e55 --- /dev/null +++ b/drivers/serial/s3c2400.c @@ -0,0 +1,106 @@ +/* linux/drivers/serial/s3c240.c + * + * Driver for Samsung SoC onboard UARTs. + * + * Ben Dooks, Copyright (c) 2003-2005 Simtec Electronics + * http://armlinux.simtec.co.uk/ + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. +*/ + +#include <linux/module.h> +#include <linux/ioport.h> +#include <linux/io.h> +#include <linux/platform_device.h> + +#include <asm/irq.h> + +#include <asm/hardware.h> + +#include <asm/plat-s3c/regs-serial.h> +#include <asm/arch/regs-gpio.h> + +#include "samsung.h" + +static int s3c2400_serial_getsource(struct uart_port *port, + struct s3c24xx_uart_clksrc *clk) +{ + clk->divisor = 1; + clk->name = "pclk"; + + return 0; +} + +static int s3c2400_serial_setsource(struct uart_port *port, + struct s3c24xx_uart_clksrc *clk) +{ + return 0; +} + +static int s3c2400_serial_resetport(struct uart_port *port, + struct s3c2410_uartcfg *cfg) +{ + dbg("s3c2400_serial_resetport: port=%p (%08lx), cfg=%p\n", + port, port->mapbase, cfg); + + wr_regl(port, S3C2410_UCON, cfg->ucon); + wr_regl(port, S3C2410_ULCON, cfg->ulcon); + + /* reset both fifos */ + + wr_regl(port, S3C2410_UFCON, cfg->ufcon | S3C2410_UFCON_RESETBOTH); + wr_regl(port, S3C2410_UFCON, cfg->ufcon); + + return 0; +} + +static struct s3c24xx_uart_info s3c2400_uart_inf = { + .name = "Samsung S3C2400 UART", + .type = PORT_S3C2400, + .fifosize = 16, + .rx_fifomask = S3C2410_UFSTAT_RXMASK, + .rx_fifoshift = S3C2410_UFSTAT_RXSHIFT, + .rx_fifofull = S3C2410_UFSTAT_RXFULL, + .tx_fifofull = S3C2410_UFSTAT_TXFULL, + .tx_fifomask = S3C2410_UFSTAT_TXMASK, + .tx_fifoshift = S3C2410_UFSTAT_TXSHIFT, + .get_clksrc = s3c2400_serial_getsource, + .set_clksrc = s3c2400_serial_setsource, + .reset_port = s3c2400_serial_resetport, +}; + +static int s3c2400_serial_probe(struct platform_device *dev) +{ + return s3c24xx_serial_probe(dev, &s3c2400_uart_inf); +} + +static struct platform_driver s3c2400_serial_drv = { + .probe = s3c2400_serial_probe, + .remove = s3c24xx_serial_remove, + .driver = { + .name = "s3c2400-uart", + .owner = THIS_MODULE, + }, +}; + +s3c24xx_console_init(&s3c2400_serial_drv, &s3c2400_uart_inf); + +static inline int s3c2400_serial_init(void) +{ + return s3c24xx_serial_init(&s3c2400_serial_drv, &s3c2400_uart_inf); +} + +static inline void s3c2400_serial_exit(void) +{ + platform_driver_unregister(&s3c2400_serial_drv); +} + +module_init(s3c2400_serial_init); +module_exit(s3c2400_serial_exit); + +MODULE_LICENSE("GPL v2"); +MODULE_AUTHOR("Ben Dooks <ben@simtec.co.uk>"); +MODULE_DESCRIPTION("Samsung S3C2400 SoC Serial port driver"); +MODULE_ALIAS("platform:s3c2400-uart"); diff --git a/drivers/serial/s3c2410.c b/drivers/serial/s3c2410.c index 2b6a013639e..c5f03f41686 100644 --- a/drivers/serial/s3c2410.c +++ b/drivers/serial/s3c2410.c @@ -1,1270 +1,30 @@ -/* - * linux/drivers/serial/s3c2410.c +/* linux/drivers/serial/s3c2410.c * - * Driver for onboard UARTs on the Samsung S3C24XX + * Driver for Samsung S3C2410 SoC onboard UARTs. * - * Based on drivers/char/serial.c and drivers/char/21285.c + * Ben Dooks, Copyright (c) 2003-2005,2008 Simtec Electronics + * http://armlinux.simtec.co.uk/ * - * Ben Dooks, (c) 2003-2005 Simtec Electronics - * http://www.simtec.co.uk/products/SWLINUX/ - * - * Changelog: - * - * 22-Jul-2004 BJD Finished off device rewrite - * - * 21-Jul-2004 BJD Thanks to <herbet@13thfloor.at> for pointing out - * problems with baud rate and loss of IR settings. Update - * to add configuration via platform_device structure - * - * 28-Sep-2004 BJD Re-write for the following items - * - S3C2410 and S3C2440 serial support - * - Power Management support - * - Fix console via IrDA devices - * - SysReq (Herbert Pötzl) - * - Break character handling (Herbert Pötzl) - * - spin-lock initialisation (Dimitry Andric) - * - added clock control - * - updated init code to use platform_device info - * - * 06-Mar-2005 BJD Add s3c2440 fclk clock source - * - * 09-Mar-2005 BJD Add s3c2400 support - * - * 10-Mar-2005 LCVR Changed S3C2410_VA_UART to S3C24XX_VA_UART -*/ - -/* Note on 2440 fclk clock source handling - * - * Whilst it is possible to use the fclk as clock source, the method - * of properly switching too/from this is currently un-implemented, so - * whichever way is configured at startup is the one that will be used. -*/ - -/* Hote on 2410 error handling - * - * The s3c2410 manual has a love/hate affair with the contents of the - * UERSTAT register in the UART blocks, and keeps marking some of the - * error bits as reserved. Having checked with the s3c2410x01, - * it copes with BREAKs properly, so I am happy to ignore the RESERVED - * feature from the latter versions of the manual. - * - * If it becomes aparrent that latter versions of the 2410 remove these - * bits, then action will have to be taken to differentiate the versions - * and change the policy on BREAK - * - * BJD, 04-Nov-2004 + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. */ - -#if defined(CONFIG_SERIAL_S3C2410_CONSOLE) && defined(CONFIG_MAGIC_SYSRQ) -#define SUPPORT_SYSRQ -#endif - #include <linux/module.h> #include <linux/ioport.h> +#include <linux/io.h> #include <linux/platform_device.h> #include <linux/init.h> -#include <linux/sysrq.h> -#include <linux/console.h> -#include <linux/tty.h> -#include <linux/tty_flip.h> #include <linux/serial_core.h> #include <linux/serial.h> -#include <linux/delay.h> -#include <linux/clk.h> -#include <asm/io.h> #include <asm/irq.h> - #include <asm/hardware.h> #include <asm/plat-s3c/regs-serial.h> #include <asm/arch/regs-gpio.h> -/* structures */ - -struct s3c24xx_uart_info { - char *name; - unsigned int type; - unsigned int fifosize; - unsigned long rx_fifomask; - unsigned long rx_fifoshift; - unsigned long rx_fifofull; - unsigned long tx_fifomask; - unsigned long tx_fifoshift; - unsigned long tx_fifofull; - - /* clock source control */ - - int (*get_clksrc)(struct uart_port *, struct s3c24xx_uart_clksrc *clk); - int (*set_clksrc)(struct uart_port *, struct s3c24xx_uart_clksrc *clk); - - /* uart controls */ - int (*reset_port)(struct uart_port *, struct s3c2410_uartcfg *); -}; - -struct s3c24xx_uart_port { - unsigned char rx_claimed; - unsigned char tx_claimed; - - struct s3c24xx_uart_info *info; - struct s3c24xx_uart_clksrc *clksrc; - struct clk *clk; - struct clk *baudclk; - struct uart_port port; -}; - - -/* configuration defines */ - -#if 0 -#if 1 -/* send debug to the low-level output routines */ - -extern void printascii(const char *); - -static void -s3c24xx_serial_dbg(const char *fmt, ...) -{ - va_list va; - char buff[256]; - - va_start(va, fmt); - vsprintf(buff, fmt, va); - va_end(va); - - printascii(buff); -} - -#define dbg(x...) s3c24xx_serial_dbg(x) - -#else -#define dbg(x...) printk(KERN_DEBUG "s3c24xx: "); -#endif -#else /* no debug */ -#define dbg(x...) do {} while(0) -#endif - -/* UART name and device definitions */ - -#define S3C24XX_SERIAL_NAME "ttySAC" -#define S3C24XX_SERIAL_MAJOR 204 -#define S3C24XX_SERIAL_MINOR 64 - - -/* conversion functions */ - -#define s3c24xx_dev_to_port(__dev) (struct uart_port *)dev_get_drvdata(__dev) -#define s3c24xx_dev_to_cfg(__dev) (struct s3c2410_uartcfg *)((__dev)->platform_data) - -/* we can support 3 uarts, but not always use them */ - -#ifdef CONFIG_CPU_S3C2400 -#define NR_PORTS (2) -#else -#define NR_PORTS (3) -#endif - -/* port irq numbers */ - -#define TX_IRQ(port) ((port)->irq + 1) -#define RX_IRQ(port) ((port)->irq) - -/* register access controls */ - -#define portaddr(port, reg) ((port)->membase + (reg)) - -#define rd_regb(port, reg) (__raw_readb(portaddr(port, reg))) -#define rd_regl(port, reg) (__raw_readl(portaddr(port, reg))) - -#define wr_regb(port, reg, val) \ - do { __raw_writeb(val, portaddr(port, reg)); } while(0) - -#define wr_regl(port, reg, val) \ - do { __raw_writel(val, portaddr(port, reg)); } while(0) - -/* macros to change one thing to another */ - -#define tx_enabled(port) ((port)->unused[0]) -#define rx_enabled(port) ((port)->unused[1]) - -/* flag to ignore all characters comming in */ -#define RXSTAT_DUMMY_READ (0x10000000) - -static inline struct s3c24xx_uart_port *to_ourport(struct uart_port *port) -{ - return container_of(port, struct s3c24xx_uart_port, port); -} - -/* translate a port to the device name */ - -static inline const char *s3c24xx_serial_portname(struct uart_port *port) -{ - return to_platform_device(port->dev)->name; -} - -static int s3c24xx_serial_txempty_nofifo(struct uart_port *port) -{ - return (rd_regl(port, S3C2410_UTRSTAT) & S3C2410_UTRSTAT_TXE); -} - -static void s3c24xx_serial_rx_enable(struct uart_port *port) -{ - unsigned long flags; - unsigned int ucon, ufcon; - int count = 10000; - - spin_lock_irqsave(&port->lock, flags); - - while (--count && !s3c24xx_serial_txempty_nofifo(port)) - udelay(100); - - ufcon = rd_regl(port, S3C2410_UFCON); - ufcon |= S3C2410_UFCON_RESETRX; - wr_regl(port, S3C2410_UFCON, ufcon); - - ucon = rd_regl(port, S3C2410_UCON); - ucon |= S3C2410_UCON_RXIRQMODE; - wr_regl(port, S3C2410_UCON, ucon); - - rx_enabled(port) = 1; - spin_unlock_irqrestore(&port->lock, flags); -} - -static void s3c24xx_serial_rx_disable(struct uart_port *port) -{ - unsigned long flags; - unsigned int ucon; - - spin_lock_irqsave(&port->lock, flags); - - ucon = rd_regl(port, S3C2410_UCON); - ucon &= ~S3C2410_UCON_RXIRQMODE; - wr_regl(port, S3C2410_UCON, ucon); - - rx_enabled(port) = 0; - spin_unlock_irqrestore(&port->lock, flags); -} - -static void s3c24xx_serial_stop_tx(struct uart_port *port) -{ - if (tx_enabled(port)) { - disable_irq(TX_IRQ(port)); - tx_enabled(port) = 0; - if (port->flags & UPF_CONS_FLOW) - s3c24xx_serial_rx_enable(port); - } -} - -static void s3c24xx_serial_start_tx(struct uart_port *port) -{ - if (!tx_enabled(port)) { - if (port->flags & UPF_CONS_FLOW) - s3c24xx_serial_rx_disable(port); - - enable_irq(TX_IRQ(port)); - tx_enabled(port) = 1; - } -} - - -static void s3c24xx_serial_stop_rx(struct uart_port *port) -{ - if (rx_enabled(port)) { - dbg("s3c24xx_serial_stop_rx: port=%p\n", port); - disable_irq(RX_IRQ(port)); - rx_enabled(port) = 0; - } -} - -static void s3c24xx_serial_enable_ms(struct uart_port *port) -{ -} - -static inline struct s3c24xx_uart_info *s3c24xx_port_to_info(struct uart_port *port) -{ - return to_ourport(port)->info; -} - -static inline struct s3c2410_uartcfg *s3c24xx_port_to_cfg(struct uart_port *port) -{ - if (port->dev == NULL) - return NULL; - - return (struct s3c2410_uartcfg *)port->dev->platform_data; -} - -static int s3c24xx_serial_rx_fifocnt(struct s3c24xx_uart_port *ourport, - unsigned long ufstat) -{ - struct s3c24xx_uart_info *info = ourport->info; - - if (ufstat & info->rx_fifofull) - return info->fifosize; - - return (ufstat & info->rx_fifomask) >> info->rx_fifoshift; -} - - -/* ? - where has parity gone?? */ -#define S3C2410_UERSTAT_PARITY (0x1000) - -static irqreturn_t -s3c24xx_serial_rx_chars(int irq, void *dev_id) -{ - struct s3c24xx_uart_port *ourport = dev_id; - struct uart_port *port = &ourport->port; - struct tty_struct *tty = port->info->tty; - unsigned int ufcon, ch, flag, ufstat, uerstat; - int max_count = 64; - - while (max_count-- > 0) { - ufcon = rd_regl(port, S3C2410_UFCON); - ufstat = rd_regl(port, S3C2410_UFSTAT); - - if (s3c24xx_serial_rx_fifocnt(ourport, ufstat) == 0) - break; - - uerstat = rd_regl(port, S3C2410_UERSTAT); - ch = rd_regb(port, S3C2410_URXH); - - if (port->flags & UPF_CONS_FLOW) { - int txe = s3c24xx_serial_txempty_nofifo(port); - - if (rx_enabled(port)) { - if (!txe) { - rx_enabled(port) = 0; - continue; - } - } else { - if (txe) { - ufcon |= S3C2410_UFCON_RESETRX; - wr_regl(port, S3C2410_UFCON, ufcon); - rx_enabled(port) = 1; - goto out; - } - continue; - } - } - - /* insert the character into the buffer */ - - flag = TTY_NORMAL; - port->icount.rx++; - - if (unlikely(uerstat & S3C2410_UERSTAT_ANY)) { - dbg("rxerr: port ch=0x%02x, rxs=0x%08x\n", - ch, uerstat); - - /* check for break */ - if (uerstat & S3C2410_UERSTAT_BREAK) { - dbg("break!\n"); - port->icount.brk++; - if (uart_handle_break(port)) - goto ignore_char; - } - - if (uerstat & S3C2410_UERSTAT_FRAME) - port->icount.frame++; - if (uerstat & S3C2410_UERSTAT_OVERRUN) - port->icount.overrun++; - - uerstat &= port->read_status_mask; - - if (uerstat & S3C2410_UERSTAT_BREAK) - flag = TTY_BREAK; - else if (uerstat & S3C2410_UERSTAT_PARITY) - flag = TTY_PARITY; - else if (uerstat & ( S3C2410_UERSTAT_FRAME | S3C2410_UERSTAT_OVERRUN)) - flag = TTY_FRAME; - } - - if (uart_handle_sysrq_char(port, ch)) - goto ignore_char; - - uart_insert_char(port, uerstat, S3C2410_UERSTAT_OVERRUN, ch, flag); - - ignore_char: - continue; - } - tty_flip_buffer_push(tty); - - out: - return IRQ_HANDLED; -} - -static irqreturn_t s3c24xx_serial_tx_chars(int irq, void *id) -{ - struct s3c24xx_uart_port *ourport = id; - struct uart_port *port = &ourport->port; - struct circ_buf *xmit = &port->info->xmit; - int count = 256; - - if (port->x_char) { - wr_regb(port, S3C2410_UTXH, port->x_char); - port->icount.tx++; - port->x_char = 0; - goto out; - } - - /* if there isnt anything more to transmit, or the uart is now - * stopped, disable the uart and exit - */ - - if (uart_circ_empty(xmit) || uart_tx_stopped(port)) { - s3c24xx_serial_stop_tx(port); - goto out; - } - - /* try and drain the buffer... */ - - while (!uart_circ_empty(xmit) && count-- > 0) { - if (rd_regl(port, S3C2410_UFSTAT) & ourport->info->tx_fifofull) - break; - - wr_regb(port, S3C2410_UTXH, xmit->buf[xmit->tail]); - xmit->tail = (xmit->tail + 1) & (UART_XMIT_SIZE - 1); - port->icount.tx++; - } - - if (uart_circ_chars_pending(xmit) < WAKEUP_CHARS) - uart_write_wakeup(port); - - if (uart_circ_empty(xmit)) - s3c24xx_serial_stop_tx(port); - - out: - return IRQ_HANDLED; -} - -static unsigned int s3c24xx_serial_tx_empty(struct uart_port *port) -{ - struct s3c24xx_uart_info *info = s3c24xx_port_to_info(port); - unsigned long ufstat = rd_regl(port, S3C2410_UFSTAT); - unsigned long ufcon = rd_regl(port, S3C2410_UFCON); - - if (ufcon & S3C2410_UFCON_FIFOMODE) { - if ((ufstat & info->tx_fifomask) != 0 || - (ufstat & info->tx_fifofull)) - return 0; - - return 1; - } - - return s3c24xx_serial_txempty_nofifo(port); -} - -/* no modem control lines */ -static unsigned int s3c24xx_serial_get_mctrl(struct uart_port *port) -{ - unsigned int umstat = rd_regb(port,S3C2410_UMSTAT); - - if (umstat & S3C2410_UMSTAT_CTS) - return TIOCM_CAR | TIOCM_DSR | TIOCM_CTS; - else - return TIOCM_CAR | TIOCM_DSR; -} - -static void s3c24xx_serial_set_mctrl(struct uart_port *port, unsigned int mctrl) -{ - /* todo - possibly remove AFC and do manual CTS */ -} - -static void s3c24xx_serial_break_ctl(struct uart_port *port, int break_state) -{ - unsigned long flags; - unsigned int ucon; - - spin_lock_irqsave(&port->lock, flags); - - ucon = rd_regl(port, S3C2410_UCON); - - if (break_state) - ucon |= S3C2410_UCON_SBREAK; - else - ucon &= ~S3C2410_UCON_SBREAK; - - wr_regl(port, S3C2410_UCON, ucon); - - spin_unlock_irqrestore(&port->lock, flags); -} - -static void s3c24xx_serial_shutdown(struct uart_port *port) -{ - struct s3c24xx_uart_port *ourport = to_ourport(port); - - if (ourport->tx_claimed) { - free_irq(TX_IRQ(port), ourport); - tx_enabled(port) = 0; - ourport->tx_claimed = 0; - } - - if (ourport->rx_claimed) { - free_irq(RX_IRQ(port), ourport); - ourport->rx_claimed = 0; - rx_enabled(port) = 0; - } -} - - -static int s3c24xx_serial_startup(struct uart_port *port) -{ - struct s3c24xx_uart_port *ourport = to_ourport(port); - int ret; - - dbg("s3c24xx_serial_startup: port=%p (%08lx,%p)\n", - port->mapbase, port->membase); - - rx_enabled(port) = 1; - - ret = request_irq(RX_IRQ(port), - s3c24xx_serial_rx_chars, 0, - s3c24xx_serial_portname(port), ourport); - - if (ret != 0) { - printk(KERN_ERR "cannot get irq %d\n", RX_IRQ(port)); - return ret; - } - - ourport->rx_claimed = 1; - - dbg("requesting tx irq...\n"); - - tx_enabled(port) = 1; - - ret = request_irq(TX_IRQ(port), - s3c24xx_serial_tx_chars, 0, - s3c24xx_serial_portname(port), ourport); - - if (ret) { - printk(KERN_ERR "cannot get irq %d\n", TX_IRQ(port)); - goto err; - } - - ourport->tx_claimed = 1; - - dbg("s3c24xx_serial_startup ok\n"); - - /* the port reset code should have done the correct - * register setup for the port controls */ - - return ret; - - err: - s3c24xx_serial_shutdown(port); - return ret; -} - -/* power power management control */ - -static void s3c24xx_serial_pm(struct uart_port *port, unsigned int level, - unsigned int old) -{ - struct s3c24xx_uart_port *ourport = to_ourport(port); - - switch (level) { - case 3: - if (!IS_ERR(ourport->baudclk) && ourport->baudclk != NULL) - clk_disable(ourport->baudclk); - - clk_disable(ourport->clk); - break; - - case 0: - clk_enable(ourport->clk); - - if (!IS_ERR(ourport->baudclk) && ourport->baudclk != NULL) - clk_enable(ourport->baudclk); - - break; - default: - printk(KERN_ERR "s3c24xx_serial: unknown pm %d\n", level); - } -} - -/* baud rate calculation - * - * The UARTs on the S3C2410/S3C2440 can take their clocks from a number - * of different sources, including the peripheral clock ("pclk") and an - * external clock ("uclk"). The S3C2440 also adds the core clock ("fclk") - * with a programmable extra divisor. - * - * The following code goes through the clock sources, and calculates the - * baud clocks (and the resultant actual baud rates) and then tries to - * pick the closest one and select that. - * -*/ - - -#define MAX_CLKS (8) - -static struct s3c24xx_uart_clksrc tmp_clksrc = { - .name = "pclk", - .min_baud = 0, - .max_baud = 0, - .divisor = 1, -}; - -static inline int -s3c24xx_serial_getsource(struct uart_port *port, struct s3c24xx_uart_clksrc *c) -{ - struct s3c24xx_uart_info *info = s3c24xx_port_to_info(port); - - return (info->get_clksrc)(port, c); -} - -static inline int -s3c24xx_serial_setsource(struct uart_port *port, struct s3c24xx_uart_clksrc *c) -{ - struct s3c24xx_uart_info *info = s3c24xx_port_to_info(port); - - return (info->set_clksrc)(port, c); -} - -struct baud_calc { - struct s3c24xx_uart_clksrc *clksrc; - unsigned int calc; - unsigned int quot; - struct clk *src; -}; - -static int s3c24xx_serial_calcbaud(struct baud_calc *calc, - struct uart_port *port, - struct s3c24xx_uart_clksrc *clksrc, - unsigned int baud) -{ - unsigned long rate; - - calc->src = clk_get(port->dev, clksrc->name); - if (calc->src == NULL || IS_ERR(calc->src)) - return 0; - - rate = clk_get_rate(calc->src); - rate /= clksrc->divisor; - - calc->clksrc = clksrc; - calc->quot = (rate + (8 * baud)) / (16 * baud); - calc->calc = (rate / (calc->quot * 16)); - - calc->quot--; - return 1; -} - -static unsigned int s3c24xx_serial_getclk(struct uart_port *port, - struct s3c24xx_uart_clksrc **clksrc, - struct clk **clk, - unsigned int baud) -{ - struct s3c2410_uartcfg *cfg = s3c24xx_port_to_cfg(port); - struct s3c24xx_uart_clksrc *clkp; - struct baud_calc res[MAX_CLKS]; - struct baud_calc *resptr, *best, *sptr; - int i; - - clkp = cfg->clocks; - best = NULL; - - if (cfg->clocks_size < 2) { - if (cfg->clocks_size == 0) - clkp = &tmp_clksrc; - - /* check to see if we're sourcing fclk, and if so we're - * going to have to update the clock source - */ - - if (strcmp(clkp->name, "fclk") == 0) { - struct s3c24xx_uart_clksrc src; - - s3c24xx_serial_getsource(port, &src); - - /* check that the port already using fclk, and if - * not, then re-select fclk - */ - - if (strcmp(src.name, clkp->name) == 0) { - s3c24xx_serial_setsource(port, clkp); - s3c24xx_serial_getsource(port, &src); - } - - clkp->divisor = src.divisor; - } - - s3c24xx_serial_calcbaud(res, port, clkp, baud); - best = res; - resptr = best + 1; - } else { - resptr = res; - - for (i = 0; i < cfg->clocks_size; i++, clkp++) { - if (s3c24xx_serial_calcbaud(resptr, port, clkp, baud)) - resptr++; - } - } - - /* ok, we now need to select the best clock we found */ - - if (!best) { - unsigned int deviation = (1<<30)|((1<<30)-1); - int calc_deviation; - - for (sptr = res; sptr < resptr; sptr++) { - printk(KERN_DEBUG - "found clk %p (%s) quot %d, calc %d\n", - sptr->clksrc, sptr->clksrc->name, - sptr->quot, sptr->calc); - - calc_deviation = baud - sptr->calc; - if (calc_deviation < 0) - calc_deviation = -calc_deviation; - - if (calc_deviation < deviation) { - best = sptr; - deviation = calc_deviation; - } - } - - printk(KERN_DEBUG "best %p (deviation %d)\n", best, deviation); - } - - printk(KERN_DEBUG "selected clock %p (%s) quot %d, calc %d\n", - best->clksrc, best->clksrc->name, best->quot, best->calc); - - /* store results to pass back */ - - *clksrc = best->clksrc; - *clk = best->src; - - return best->quot; -} - -static void s3c24xx_serial_set_termios(struct uart_port *port, - struct ktermios *termios, - struct ktermios *old) -{ - struct s3c2410_uartcfg *cfg = s3c24xx_port_to_cfg(port); - struct s3c24xx_uart_port *ourport = to_ourport(port); - struct s3c24xx_uart_clksrc *clksrc = NULL; - struct clk *clk = NULL; - unsigned long flags; - unsigned int baud, quot; - unsigned int ulcon; - unsigned int umcon; - - /* - * We don't support modem control lines. - */ - termios->c_cflag &= ~(HUPCL | CMSPAR); - termios->c_cflag |= CLOCAL; - - /* - * Ask the core to calculate the divisor for us. - */ - - baud = uart_get_baud_rate(port, termios, old, 0, 115200*8); - - if (baud == 38400 && (port->flags & UPF_SPD_MASK) == UPF_SPD_CUST) - quot = port->custom_divisor; - else - quot = s3c24xx_serial_getclk(port, &clksrc, &clk, baud); - - /* check to see if we need to change clock source */ - - if (ourport->clksrc != clksrc || ourport->baudclk != clk) { - s3c24xx_serial_setsource(port, clksrc); - - if (ourport->baudclk != NULL && !IS_ERR(ourport->baudclk)) { - clk_disable(ourport->baudclk); - ourport->baudclk = NULL; - } - - clk_enable(clk); - - ourport->clksrc = clksrc; - ourport->baudclk = clk; - } - - switch (termios->c_cflag & CSIZE) { - case CS5: - dbg("config: 5bits/char\n"); - ulcon = S3C2410_LCON_CS5; - break; - case CS6: - dbg("config: 6bits/char\n"); - ulcon = S3C2410_LCON_CS6; - break; - case CS7: - dbg("config: 7bits/char\n"); - ulcon = S3C2410_LCON_CS7; - break; - case CS8: - default: - dbg("config: 8bits/char\n"); - ulcon = S3C2410_LCON_CS8; - break; - } - - /* preserve original lcon IR settings */ - ulcon |= (cfg->ulcon & S3C2410_LCON_IRM); - - if (termios->c_cflag & CSTOPB) - ulcon |= S3C2410_LCON_STOPB; - - umcon = (termios->c_cflag & CRTSCTS) ? S3C2410_UMCOM_AFC : 0; - - if (termios->c_cflag & PARENB) { - if (termios->c_cflag & PARODD) - ulcon |= S3C2410_LCON_PODD; - else - ulcon |= S3C2410_LCON_PEVEN; - } else { - ulcon |= S3C2410_LCON_PNONE; - } - - spin_lock_irqsave(&port->lock, flags); - - dbg("setting ulcon to %08x, brddiv to %d\n", ulcon, quot); - - wr_regl(port, S3C2410_ULCON, ulcon); - wr_regl(port, S3C2410_UBRDIV, quot); - wr_regl(port, S3C2410_UMCON, umcon); - - dbg("uart: ulcon = 0x%08x, ucon = 0x%08x, ufcon = 0x%08x\n", - rd_regl(port, S3C2410_ULCON), - rd_regl(port, S3C2410_UCON), - rd_regl(port, S3C2410_UFCON)); - - /* - * Update the per-port timeout. - */ - uart_update_timeout(port, termios->c_cflag, baud); - - /* - * Which character status flags are we interested in? - */ - port->read_status_mask = S3C2410_UERSTAT_OVERRUN; - if (termios->c_iflag & INPCK) - port->read_status_mask |= S3C2410_UERSTAT_FRAME | S3C2410_UERSTAT_PARITY; - - /* - * Which character status flags should we ignore? - */ - port->ignore_status_mask = 0; - if (termios->c_iflag & IGNPAR) - port->ignore_status_mask |= S3C2410_UERSTAT_OVERRUN; - if (termios->c_iflag & IGNBRK && termios->c_iflag & IGNPAR) - port->ignore_status_mask |= S3C2410_UERSTAT_FRAME; - - /* - * Ignore all characters if CREAD is not set. - */ - if ((termios->c_cflag & CREAD) == 0) - port->ignore_status_mask |= RXSTAT_DUMMY_READ; - - spin_unlock_irqrestore(&port->lock, flags); -} - -static const char *s3c24xx_serial_type(struct uart_port *port) -{ - switch (port->type) { - case PORT_S3C2410: - return "S3C2410"; - case PORT_S3C2440: - return "S3C2440"; - case PORT_S3C2412: - return "S3C2412"; - default: - return NULL; - } -} - -#define MAP_SIZE (0x100) - -static void s3c24xx_serial_release_port(struct uart_port *port) -{ - release_mem_region(port->mapbase, MAP_SIZE); -} - -static int s3c24xx_serial_request_port(struct uart_port *port) -{ - const char *name = s3c24xx_serial_portname(port); - return request_mem_region(port->mapbase, MAP_SIZE, name) ? 0 : -EBUSY; -} - -static void s3c24xx_serial_config_port(struct uart_port *port, int flags) -{ - struct s3c24xx_uart_info *info = s3c24xx_port_to_info(port); - - if (flags & UART_CONFIG_TYPE && - s3c24xx_serial_request_port(port) == 0) - port->type = info->type; -} - -/* - * verify the new serial_struct (for TIOCSSERIAL). - */ -static int -s3c24xx_serial_verify_port(struct uart_port *port, struct serial_struct *ser) -{ - struct s3c24xx_uart_info *info = s3c24xx_port_to_info(port); - - if (ser->type != PORT_UNKNOWN && ser->type != info->type) - return -EINVAL; - - return 0; -} - - -#ifdef CONFIG_SERIAL_S3C2410_CONSOLE - -static struct console s3c24xx_serial_console; - -#define S3C24XX_SERIAL_CONSOLE &s3c24xx_serial_console -#else -#define S3C24XX_SERIAL_CONSOLE NULL -#endif - -static struct uart_ops s3c24xx_serial_ops = { - .pm = s3c24xx_serial_pm, - .tx_empty = s3c24xx_serial_tx_empty, - .get_mctrl = s3c24xx_serial_get_mctrl, - .set_mctrl = s3c24xx_serial_set_mctrl, - .stop_tx = s3c24xx_serial_stop_tx, - .start_tx = s3c24xx_serial_start_tx, - .stop_rx = s3c24xx_serial_stop_rx, - .enable_ms = s3c24xx_serial_enable_ms, - .break_ctl = s3c24xx_serial_break_ctl, - .startup = s3c24xx_serial_startup, - .shutdown = s3c24xx_serial_shutdown, - .set_termios = s3c24xx_serial_set_termios, - .type = s3c24xx_serial_type, - .release_port = s3c24xx_serial_release_port, - .request_port = s3c24xx_serial_request_port, - .config_port = s3c24xx_serial_config_port, - .verify_port = s3c24xx_serial_verify_port, -}; - - -static struct uart_driver s3c24xx_uart_drv = { - .owner = THIS_MODULE, - .dev_name = "s3c2410_serial", - .nr = 3, - .cons = S3C24XX_SERIAL_CONSOLE, - .driver_name = S3C24XX_SERIAL_NAME, - .major = S3C24XX_SERIAL_MAJOR, - .minor = S3C24XX_SERIAL_MINOR, -}; - -static struct s3c24xx_uart_port s3c24xx_serial_ports[NR_PORTS] = { - [0] = { - .port = { - .lock = __SPIN_LOCK_UNLOCKED(s3c24xx_serial_ports[0].port.lock), - .iotype = UPIO_MEM, - .irq = IRQ_S3CUART_RX0, - .uartclk = 0, - .fifosize = 16, - .ops = &s3c24xx_serial_ops, - .flags = UPF_BOOT_AUTOCONF, - .line = 0, - } - }, - [1] = { - .port = { - .lock = __SPIN_LOCK_UNLOCKED(s3c24xx_serial_ports[1].port.lock), - .iotype = UPIO_MEM, - .irq = IRQ_S3CUART_RX1, - .uartclk = 0, - .fifosize = 16, - .ops = &s3c24xx_serial_ops, - .flags = UPF_BOOT_AUTOCONF, - .line = 1, - } - }, -#if NR_PORTS > 2 - - [2] = { - .port = { - .lock = __SPIN_LOCK_UNLOCKED(s3c24xx_serial_ports[2].port.lock), - .iotype = UPIO_MEM, - .irq = IRQ_S3CUART_RX2, - .uartclk = 0, - .fifosize = 16, - .ops = &s3c24xx_serial_ops, - .flags = UPF_BOOT_AUTOCONF, - .line = 2, - } - } -#endif -}; - -/* s3c24xx_serial_resetport - * - * wrapper to call the specific reset for this port (reset the fifos - * and the settings) -*/ - -static inline int s3c24xx_serial_resetport(struct uart_port * port, - struct s3c2410_uartcfg *cfg) -{ - struct s3c24xx_uart_info *info = s3c24xx_port_to_info(port); - - return (info->reset_port)(port, cfg); -} - -/* s3c24xx_serial_init_port - * - * initialise a single serial port from the platform device given - */ - -static int s3c24xx_serial_init_port(struct s3c24xx_uart_port *ourport, - struct s3c24xx_uart_info *info, - struct platform_device *platdev) -{ - struct uart_port *port = &ourport->port; - struct s3c2410_uartcfg *cfg; - struct resource *res; - int ret; - - dbg("s3c24xx_serial_init_port: port=%p, platdev=%p\n", port, platdev); - - if (platdev == NULL) - return -ENODEV; - - cfg = s3c24xx_dev_to_cfg(&platdev->dev); - - if (port->mapbase != 0) - return 0; - - if (cfg->hwport > 3) - return -EINVAL; - - /* setup info for port */ - port->dev = &platdev->dev; - ourport->info = info; - - /* copy the info in from provided structure */ - ourport->port.fifosize = info->fifosize; - - dbg("s3c24xx_serial_init_port: %p (hw %d)...\n", port, cfg->hwport); - - port->uartclk = 1; - - if (cfg->uart_flags & UPF_CONS_FLOW) { - dbg("s3c24xx_serial_init_port: enabling flow control\n"); - port->flags |= UPF_CONS_FLOW; - } - - /* sort our the physical and virtual addresses for each UART */ - - res = platform_get_resource(platdev, IORESOURCE_MEM, 0); - if (res == NULL) { - printk(KERN_ERR "failed to find memory resource for uart\n"); - return -EINVAL; - } - - dbg("resource %p (%lx..%lx)\n", res, res->start, res->end); - - port->mapbase = res->start; - port->membase = S3C24XX_VA_UART + (res->start - S3C24XX_PA_UART); - ret = platform_get_irq(platdev, 0); - if (ret < 0) - port->irq = 0; - else - port->irq = ret; - - ourport->clk = clk_get(&platdev->dev, "uart"); - - dbg("port: map=%08x, mem=%08x, irq=%d, clock=%ld\n", - port->mapbase, port->membase, port->irq, port->uartclk); - - /* reset the fifos (and setup the uart) */ - s3c24xx_serial_resetport(port, cfg); - return 0; -} - -/* Device driver serial port probe */ - -static int probe_index = 0; - -static int s3c24xx_serial_probe(struct platform_device *dev, - struct s3c24xx_uart_info *info) -{ - struct s3c24xx_uart_port *ourport; - int ret; - - dbg("s3c24xx_serial_probe(%p, %p) %d\n", dev, info, probe_index); - - ourport = &s3c24xx_serial_ports[probe_index]; - probe_index++; - - dbg("%s: initialising port %p...\n", __func__, ourport); - - ret = s3c24xx_serial_init_port(ourport, info, dev); - if (ret < 0) - goto probe_err; - - dbg("%s: adding port\n", __func__); - uart_add_one_port(&s3c24xx_uart_drv, &ourport->port); - platform_set_drvdata(dev, &ourport->port); - - return 0; - - probe_err: - return ret; -} - -static int s3c24xx_serial_remove(struct platform_device *dev) -{ - struct uart_port *port = s3c24xx_dev_to_port(&dev->dev); - - if (port) - uart_remove_one_port(&s3c24xx_uart_drv, port); - - return 0; -} - -/* UART power management code */ - -#ifdef CONFIG_PM - -static int s3c24xx_serial_suspend(struct platform_device *dev, pm_message_t state) -{ - struct uart_port *port = s3c24xx_dev_to_port(&dev->dev); - - if (port) - uart_suspend_port(&s3c24xx_uart_drv, port); - - return 0; -} - -static int s3c24xx_serial_resume(struct platform_device *dev) -{ - struct uart_port *port = s3c24xx_dev_to_port(&dev->dev); - struct s3c24xx_uart_port *ourport = to_ourport(port); - - if (port) { - clk_enable(ourport->clk); - s3c24xx_serial_resetport(port, s3c24xx_port_to_cfg(port)); - clk_disable(ourport->clk); - - uart_resume_port(&s3c24xx_uart_drv, port); - } - - return 0; -} - -#else -#define s3c24xx_serial_suspend NULL -#define s3c24xx_serial_resume NULL -#endif - -static int s3c24xx_serial_init(struct platform_driver *drv, - struct s3c24xx_uart_info *info) -{ - dbg("s3c24xx_serial_init(%p,%p)\n", drv, info); - return platform_driver_register(drv); -} - - -/* now comes the code to initialise either the s3c2410 or s3c2440 serial - * port information -*/ - -/* cpu specific variations on the serial port support */ - -#ifdef CONFIG_CPU_S3C2400 - -static int s3c2400_serial_getsource(struct uart_port *port, - struct s3c24xx_uart_clksrc *clk) -{ - clk->divisor = 1; - clk->name = "pclk"; - - return 0; -} - -static int s3c2400_serial_setsource(struct uart_port *port, - struct s3c24xx_uart_clksrc *clk) -{ - return 0; -} - -static int s3c2400_serial_resetport(struct uart_port *port, - struct s3c2410_uartcfg *cfg) -{ - dbg("s3c2400_serial_resetport: port=%p (%08lx), cfg=%p\n", - port, port->mapbase, cfg); - - wr_regl(port, S3C2410_UCON, cfg->ucon); - wr_regl(port, S3C2410_ULCON, cfg->ulcon); - - /* reset both fifos */ - - wr_regl(port, S3C2410_UFCON, cfg->ufcon | S3C2410_UFCON_RESETBOTH); - wr_regl(port, S3C2410_UFCON, cfg->ufcon); - - return 0; -} - -static struct s3c24xx_uart_info s3c2400_uart_inf = { - .name = "Samsung S3C2400 UART", - .type = PORT_S3C2400, - .fifosize = 16, - .rx_fifomask = S3C2410_UFSTAT_RXMASK, - .rx_fifoshift = S3C2410_UFSTAT_RXSHIFT, - .rx_fifofull = S3C2410_UFSTAT_RXFULL, - .tx_fifofull = S3C2410_UFSTAT_TXFULL, - .tx_fifomask = S3C2410_UFSTAT_TXMASK, - .tx_fifoshift = S3C2410_UFSTAT_TXSHIFT, - .get_clksrc = s3c2400_serial_getsource, - .set_clksrc = s3c2400_serial_setsource, - .reset_port = s3c2400_serial_resetport, -}; - -static int s3c2400_serial_probe(struct platform_device *dev) -{ - return s3c24xx_serial_probe(dev, &s3c2400_uart_inf); -} - -static struct platform_driver s3c2400_serial_drv = { - .probe = s3c2400_serial_probe, - .remove = s3c24xx_serial_remove, - .suspend = s3c24xx_serial_suspend, - .resume = s3c24xx_serial_resume, - .driver = { - .name = "s3c2400-uart", - .owner = THIS_MODULE, - }, -}; - -static inline int s3c2400_serial_init(void) -{ - return s3c24xx_serial_init(&s3c2400_serial_drv, &s3c2400_uart_inf); -} - -static inline void s3c2400_serial_exit(void) -{ - platform_driver_unregister(&s3c2400_serial_drv); -} - -#define s3c2400_uart_inf_at &s3c2400_uart_inf -#else - -static inline int s3c2400_serial_init(void) -{ - return 0; -} - -static inline void s3c2400_serial_exit(void) -{ -} - -#define s3c2400_uart_inf_at NULL - -#endif /* CONFIG_CPU_S3C2400 */ - -/* S3C2410 support */ - -#ifdef CONFIG_CPU_S3C2410 +#include "samsung.h" static int s3c2410_serial_setsource(struct uart_port *port, struct s3c24xx_uart_clksrc *clk) @@ -1323,8 +83,6 @@ static struct s3c24xx_uart_info s3c2410_uart_inf = { .reset_port = s3c2410_serial_resetport, }; -/* device management */ - static int s3c2410_serial_probe(struct platform_device *dev) { return s3c24xx_serial_probe(dev, &s3c2410_uart_inf); @@ -1333,612 +91,28 @@ static int s3c2410_serial_probe(struct platform_device *dev) static struct platform_driver s3c2410_serial_drv = { .probe = s3c2410_serial_probe, .remove = s3c24xx_serial_remove, - .suspend = s3c24xx_serial_suspend, - .resume = s3c24xx_serial_resume, .driver = { .name = "s3c2410-uart", .owner = THIS_MODULE, }, }; -static inline int s3c2410_serial_init(void) +s3c24xx_console_init(&s3c2410_serial_drv, &s3c2410_uart_inf); + +static int __init s3c2410_serial_init(void) { return s3c24xx_serial_init(&s3c2410_serial_drv, &s3c2410_uart_inf); } -static inline void s3c2410_serial_exit(void) +static void __exit s3c2410_serial_exit(void) { platform_driver_unregister(&s3c2410_serial_drv); } -#define s3c2410_uart_inf_at &s3c2410_uart_inf -#else - -static inline int s3c2410_serial_init(void) -{ - return 0; -} - -static inline void s3c2410_serial_exit(void) -{ -} - -#define s3c2410_uart_inf_at NULL - -#endif /* CONFIG_CPU_S3C2410 */ - -#if defined(CONFIG_CPU_S3C2440) || defined(CONFIG_CPU_S3C2442) - -static int s3c2440_serial_setsource(struct uart_port *port, - struct s3c24xx_uart_clksrc *clk) -{ - unsigned long ucon = rd_regl(port, S3C2410_UCON); - - // todo - proper fclk<>nonfclk switch // - - ucon &= ~S3C2440_UCON_CLKMASK; - - if (strcmp(clk->name, "uclk") == 0) - ucon |= S3C2440_UCON_UCLK; - else if (strcmp(clk->name, "pclk") == 0) - ucon |= S3C2440_UCON_PCLK; - else if (strcmp(clk->name, "fclk") == 0) - ucon |= S3C2440_UCON_FCLK; - else { - printk(KERN_ERR "unknown clock source %s\n", clk->name); - return -EINVAL; - } - - wr_regl(port, S3C2410_UCON, ucon); - return 0; -} - - -static int s3c2440_serial_getsource(struct uart_port *port, - struct s3c24xx_uart_clksrc *clk) -{ - unsigned long ucon = rd_regl(port, S3C2410_UCON); - unsigned long ucon0, ucon1, ucon2; - - switch (ucon & S3C2440_UCON_CLKMASK) { - case S3C2440_UCON_UCLK: - clk->divisor = 1; - clk->name = "uclk"; - break; - - case S3C2440_UCON_PCLK: - case S3C2440_UCON_PCLK2: - clk->divisor = 1; - clk->name = "pclk"; - break; - - case S3C2440_UCON_FCLK: - /* the fun of calculating the uart divisors on - * the s3c2440 */ - - ucon0 = __raw_readl(S3C24XX_VA_UART0 + S3C2410_UCON); - ucon1 = __raw_readl(S3C24XX_VA_UART1 + S3C2410_UCON); - ucon2 = __raw_readl(S3C24XX_VA_UART2 + S3C2410_UCON); - - printk("ucons: %08lx, %08lx, %08lx\n", ucon0, ucon1, ucon2); - - ucon0 &= S3C2440_UCON0_DIVMASK; - ucon1 &= S3C2440_UCON1_DIVMASK; - ucon2 &= S3C2440_UCON2_DIVMASK; - - if (ucon0 != 0) { - clk->divisor = ucon0 >> S3C2440_UCON_DIVSHIFT; - clk->divisor += 6; - } else if (ucon1 != 0) { - clk->divisor = ucon1 >> S3C2440_UCON_DIVSHIFT; - clk->divisor += 21; - } else if (ucon2 != 0) { - clk->divisor = ucon2 >> S3C2440_UCON_DIVSHIFT; - clk->divisor += 36; - } else { - /* manual calims 44, seems to be 9 */ - clk->divisor = 9; - } - - clk->name = "fclk"; - break; - } - - return 0; -} - -static int s3c2440_serial_resetport(struct uart_port *port, - struct s3c2410_uartcfg *cfg) -{ - unsigned long ucon = rd_regl(port, S3C2410_UCON); - - dbg("s3c2440_serial_resetport: port=%p (%08lx), cfg=%p\n", - port, port->mapbase, cfg); - - /* ensure we don't change the clock settings... */ - - ucon &= (S3C2440_UCON0_DIVMASK | (3<<10)); - - wr_regl(port, S3C2410_UCON, ucon | cfg->ucon); - wr_regl(port, S3C2410_ULCON, cfg->ulcon); - - /* reset both fifos */ - - wr_regl(port, S3C2410_UFCON, cfg->ufcon | S3C2410_UFCON_RESETBOTH); - wr_regl(port, S3C2410_UFCON, cfg->ufcon); - - return 0; -} - -static struct s3c24xx_uart_info s3c2440_uart_inf = { - .name = "Samsung S3C2440 UART", - .type = PORT_S3C2440, - .fifosize = 64, - .rx_fifomask = S3C2440_UFSTAT_RXMASK, - .rx_fifoshift = S3C2440_UFSTAT_RXSHIFT, - .rx_fifofull = S3C2440_UFSTAT_RXFULL, - .tx_fifofull = S3C2440_UFSTAT_TXFULL, - .tx_fifomask = S3C2440_UFSTAT_TXMASK, - .tx_fifoshift = S3C2440_UFSTAT_TXSHIFT, - .get_clksrc = s3c2440_serial_getsource, - .set_clksrc = s3c2440_serial_setsource, - .reset_port = s3c2440_serial_resetport, -}; - -/* device management */ - -static int s3c2440_serial_probe(struct platform_device *dev) -{ - dbg("s3c2440_serial_probe: dev=%p\n", dev); - return s3c24xx_serial_probe(dev, &s3c2440_uart_inf); -} - -static struct platform_driver s3c2440_serial_drv = { - .probe = s3c2440_serial_probe, - .remove = s3c24xx_serial_remove, - .suspend = s3c24xx_serial_suspend, - .resume = s3c24xx_serial_resume, - .driver = { - .name = "s3c2440-uart", - .owner = THIS_MODULE, - }, -}; - - -static inline int s3c2440_serial_init(void) -{ - return s3c24xx_serial_init(&s3c2440_serial_drv, &s3c2440_uart_inf); -} - -static inline void s3c2440_serial_exit(void) -{ - platform_driver_unregister(&s3c2440_serial_drv); -} - -#define s3c2440_uart_inf_at &s3c2440_uart_inf -#else - -static inline int s3c2440_serial_init(void) -{ - return 0; -} - -static inline void s3c2440_serial_exit(void) -{ -} - -#define s3c2440_uart_inf_at NULL -#endif /* CONFIG_CPU_S3C2440 */ - -#if defined(CONFIG_CPU_S3C2412) - -static int s3c2412_serial_setsource(struct uart_port *port, - struct s3c24xx_uart_clksrc *clk) -{ - unsigned long ucon = rd_regl(port, S3C2410_UCON); - - ucon &= ~S3C2412_UCON_CLKMASK; - - if (strcmp(clk->name, "uclk") == 0) - ucon |= S3C2440_UCON_UCLK; - else if (strcmp(clk->name, "pclk") == 0) - ucon |= S3C2440_UCON_PCLK; - else if (strcmp(clk->name, "usysclk") == 0) - ucon |= S3C2412_UCON_USYSCLK; - else { - printk(KERN_ERR "unknown clock source %s\n", clk->name); - return -EINVAL; - } - - wr_regl(port, S3C2410_UCON, ucon); - return 0; -} - - -static int s3c2412_serial_getsource(struct uart_port *port, - struct s3c24xx_uart_clksrc *clk) -{ - unsigned long ucon = rd_regl(port, S3C2410_UCON); - - switch (ucon & S3C2412_UCON_CLKMASK) { - case S3C2412_UCON_UCLK: - clk->divisor = 1; - clk->name = "uclk"; - break; - - case S3C2412_UCON_PCLK: - case S3C2412_UCON_PCLK2: - clk->divisor = 1; - clk->name = "pclk"; - break; - - case S3C2412_UCON_USYSCLK: - clk->divisor = 1; - clk->name = "usysclk"; - break; - } - - return 0; -} - -static int s3c2412_serial_resetport(struct uart_port *port, - struct s3c2410_uartcfg *cfg) -{ - unsigned long ucon = rd_regl(port, S3C2410_UCON); - - dbg("%s: port=%p (%08lx), cfg=%p\n", - __func__, port, port->mapbase, cfg); - - /* ensure we don't change the clock settings... */ - - ucon &= S3C2412_UCON_CLKMASK; - - wr_regl(port, S3C2410_UCON, ucon | cfg->ucon); - wr_regl(port, S3C2410_ULCON, cfg->ulcon); - - /* reset both fifos */ - - wr_regl(port, S3C2410_UFCON, cfg->ufcon | S3C2410_UFCON_RESETBOTH); - wr_regl(port, S3C2410_UFCON, cfg->ufcon); - - return 0; -} - -static struct s3c24xx_uart_info s3c2412_uart_inf = { - .name = "Samsung S3C2412 UART", - .type = PORT_S3C2412, - .fifosize = 64, - .rx_fifomask = S3C2440_UFSTAT_RXMASK, - .rx_fifoshift = S3C2440_UFSTAT_RXSHIFT, - .rx_fifofull = S3C2440_UFSTAT_RXFULL, - .tx_fifofull = S3C2440_UFSTAT_TXFULL, - .tx_fifomask = S3C2440_UFSTAT_TXMASK, - .tx_fifoshift = S3C2440_UFSTAT_TXSHIFT, - .get_clksrc = s3c2412_serial_getsource, - .set_clksrc = s3c2412_serial_setsource, - .reset_port = s3c2412_serial_resetport, -}; - -/* device management */ - -static int s3c2412_serial_probe(struct platform_device *dev) -{ - dbg("s3c2440_serial_probe: dev=%p\n", dev); - return s3c24xx_serial_probe(dev, &s3c2412_uart_inf); -} - -static struct platform_driver s3c2412_serial_drv = { - .probe = s3c2412_serial_probe, - .remove = s3c24xx_serial_remove, - .suspend = s3c24xx_serial_suspend, - .resume = s3c24xx_serial_resume, - .driver = { - .name = "s3c2412-uart", - .owner = THIS_MODULE, - }, -}; - - -static inline int s3c2412_serial_init(void) -{ - return s3c24xx_serial_init(&s3c2412_serial_drv, &s3c2412_uart_inf); -} - -static inline void s3c2412_serial_exit(void) -{ - platform_driver_unregister(&s3c2412_serial_drv); -} - -#define s3c2412_uart_inf_at &s3c2412_uart_inf -#else - -static inline int s3c2412_serial_init(void) -{ - return 0; -} - -static inline void s3c2412_serial_exit(void) -{ -} - -#define s3c2412_uart_inf_at NULL -#endif /* CONFIG_CPU_S3C2440 */ - - -/* module initialisation code */ - -static int __init s3c24xx_serial_modinit(void) -{ - int ret; - - ret = uart_register_driver(&s3c24xx_uart_drv); - if (ret < 0) { - printk(KERN_ERR "failed to register UART driver\n"); - return -1; - } - - s3c2400_serial_init(); - s3c2410_serial_init(); - s3c2412_serial_init(); - s3c2440_serial_init(); - - return 0; -} - -static void __exit s3c24xx_serial_modexit(void) -{ - s3c2400_serial_exit(); - s3c2410_serial_exit(); - s3c2412_serial_exit(); - s3c2440_serial_exit(); - - uart_unregister_driver(&s3c24xx_uart_drv); -} - - -module_init(s3c24xx_serial_modinit); -module_exit(s3c24xx_serial_modexit); - -/* Console code */ - -#ifdef CONFIG_SERIAL_S3C2410_CONSOLE - -static struct uart_port *cons_uart; - -static int -s3c24xx_serial_console_txrdy(struct uart_port *port, unsigned int ufcon) -{ - struct s3c24xx_uart_info *info = s3c24xx_port_to_info(port); - unsigned long ufstat, utrstat; - - if (ufcon & S3C2410_UFCON_FIFOMODE) { - /* fifo mode - check ammount of data in fifo registers... */ - - ufstat = rd_regl(port, S3C2410_UFSTAT); - return (ufstat & info->tx_fifofull) ? 0 : 1; - } - - /* in non-fifo mode, we go and use the tx buffer empty */ - - utrstat = rd_regl(port, S3C2410_UTRSTAT); - return (utrstat & S3C2410_UTRSTAT_TXE) ? 1 : 0; -} - -static void -s3c24xx_serial_console_putchar(struct uart_port *port, int ch) -{ - unsigned int ufcon = rd_regl(cons_uart, S3C2410_UFCON); - while (!s3c24xx_serial_console_txrdy(port, ufcon)) - barrier(); - wr_regb(cons_uart, S3C2410_UTXH, ch); -} - -static void -s3c24xx_serial_console_write(struct console *co, const char *s, - unsigned int count) -{ - uart_console_write(cons_uart, s, count, s3c24xx_serial_console_putchar); -} - -static void __init -s3c24xx_serial_get_options(struct uart_port *port, int *baud, - int *parity, int *bits) -{ - struct s3c24xx_uart_clksrc clksrc; - struct clk *clk; - unsigned int ulcon; - unsigned int ucon; - unsigned int ubrdiv; - unsigned long rate; - - ulcon = rd_regl(port, S3C2410_ULCON); - ucon = rd_regl(port, S3C2410_UCON); - ubrdiv = rd_regl(port, S3C2410_UBRDIV); - - dbg("s3c24xx_serial_get_options: port=%p\n" - "registers: ulcon=%08x, ucon=%08x, ubdriv=%08x\n", - port, ulcon, ucon, ubrdiv); - - if ((ucon & 0xf) != 0) { - /* consider the serial port configured if the tx/rx mode set */ - - switch (ulcon & S3C2410_LCON_CSMASK) { - case S3C2410_LCON_CS5: - *bits = 5; - break; - case S3C2410_LCON_CS6: - *bits = 6; - break; - case S3C2410_LCON_CS7: - *bits = 7; - break; - default: - case S3C2410_LCON_CS8: - *bits = 8; - break; - } - - switch (ulcon & S3C2410_LCON_PMASK) { - case S3C2410_LCON_PEVEN: - *parity = 'e'; - break; - - case S3C2410_LCON_PODD: - *parity = 'o'; - break; - - case S3C2410_LCON_PNONE: - default: - *parity = 'n'; - } - - /* now calculate the baud rate */ - - s3c24xx_serial_getsource(port, &clksrc); - - clk = clk_get(port->dev, clksrc.name); - if (!IS_ERR(clk) && clk != NULL) - rate = clk_get_rate(clk) / clksrc.divisor; - else - rate = 1; - - - *baud = rate / ( 16 * (ubrdiv + 1)); - dbg("calculated baud %d\n", *baud); - } - -} - -/* s3c24xx_serial_init_ports - * - * initialise the serial ports from the machine provided initialisation - * data. -*/ - -static int s3c24xx_serial_init_ports(struct s3c24xx_uart_info *info) -{ - struct s3c24xx_uart_port *ptr = s3c24xx_serial_ports; - struct platform_device **platdev_ptr; - int i; - - dbg("s3c24xx_serial_init_ports: initialising ports...\n"); - - platdev_ptr = s3c24xx_uart_devs; - - for (i = 0; i < NR_PORTS; i++, ptr++, platdev_ptr++) { - s3c24xx_serial_init_port(ptr, info, *platdev_ptr); - } - - return 0; -} - -static int __init -s3c24xx_serial_console_setup(struct console *co, char *options) -{ - struct uart_port *port; - int baud = 9600; - int bits = 8; - int parity = 'n'; - int flow = 'n'; - - dbg("s3c24xx_serial_console_setup: co=%p (%d), %s\n", - co, co->index, options); - - /* is this a valid port */ - - if (co->index == -1 || co->index >= NR_PORTS) - co->index = 0; - - port = &s3c24xx_serial_ports[co->index].port; - - /* is the port configured? */ - - if (port->mapbase == 0x0) { - co->index = 0; - port = &s3c24xx_serial_ports[co->index].port; - } - - cons_uart = port; - - dbg("s3c24xx_serial_console_setup: port=%p (%d)\n", port, co->index); - - /* - * Check whether an invalid uart number has been specified, and - * if so, search for the first available port that does have - * console support. - */ - if (options) - uart_parse_options(options, &baud, &parity, &bits, &flow); - else - s3c24xx_serial_get_options(port, &baud, &parity, &bits); - - dbg("s3c24xx_serial_console_setup: baud %d\n", baud); - - return uart_set_options(port, co, baud, parity, bits, flow); -} - -/* s3c24xx_serial_initconsole - * - * initialise the console from one of the uart drivers -*/ - -static struct console s3c24xx_serial_console = -{ - .name = S3C24XX_SERIAL_NAME, - .device = uart_console_device, - .flags = CON_PRINTBUFFER, - .index = -1, - .write = s3c24xx_serial_console_write, - .setup = s3c24xx_serial_console_setup -}; - -static int s3c24xx_serial_initconsole(void) -{ - struct s3c24xx_uart_info *info; - struct platform_device *dev = s3c24xx_uart_devs[0]; - - dbg("s3c24xx_serial_initconsole\n"); - - /* select driver based on the cpu */ - - if (dev == NULL) { - printk(KERN_ERR "s3c24xx: no devices for console init\n"); - return 0; - } - - if (strcmp(dev->name, "s3c2400-uart") == 0) { - info = s3c2400_uart_inf_at; - } else if (strcmp(dev->name, "s3c2410-uart") == 0) { - info = s3c2410_uart_inf_at; - } else if (strcmp(dev->name, "s3c2440-uart") == 0) { - info = s3c2440_uart_inf_at; - } else if (strcmp(dev->name, "s3c2412-uart") == 0) { - info = s3c2412_uart_inf_at; - } else { - printk(KERN_ERR "s3c24xx: no driver for %s\n", dev->name); - return 0; - } - - if (info == NULL) { - printk(KERN_ERR "s3c24xx: no driver for console\n"); - return 0; - } - - s3c24xx_serial_console.data = &s3c24xx_uart_drv; - s3c24xx_serial_init_ports(info); - - register_console(&s3c24xx_serial_console); - return 0; -} - -console_initcall(s3c24xx_serial_initconsole); - -#endif /* CONFIG_SERIAL_S3C2410_CONSOLE */ +module_init(s3c2410_serial_init); +module_exit(s3c2410_serial_exit); -MODULE_LICENSE("GPL"); +MODULE_LICENSE("GPL v2"); MODULE_AUTHOR("Ben Dooks <ben@simtec.co.uk>"); -MODULE_DESCRIPTION("Samsung S3C2410/S3C2440/S3C2412 Serial port driver"); -MODULE_ALIAS("platform:s3c2400-uart"); +MODULE_DESCRIPTION("Samsung S3C2410 SoC Serial port driver"); MODULE_ALIAS("platform:s3c2410-uart"); -MODULE_ALIAS("platform:s3c2412-uart"); -MODULE_ALIAS("platform:s3c2440-uart"); diff --git a/drivers/serial/s3c2412.c b/drivers/serial/s3c2412.c new file mode 100644 index 00000000000..ce0c220e3e9 --- /dev/null +++ b/drivers/serial/s3c2412.c @@ -0,0 +1,151 @@ +/* linux/drivers/serial/s3c2412.c + * + * Driver for Samsung S3C2412 and S3C2413 SoC onboard UARTs. + * + * Ben Dooks, Copyright (c) 2003-2005,2008 Simtec Electronics + * http://armlinux.simtec.co.uk/ + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. +*/ + +#include <linux/module.h> +#include <linux/ioport.h> +#include <linux/io.h> +#include <linux/platform_device.h> +#include <linux/init.h> +#include <linux/serial_core.h> +#include <linux/serial.h> + +#include <asm/irq.h> +#include <asm/hardware.h> + +#include <asm/plat-s3c/regs-serial.h> +#include <asm/arch/regs-gpio.h> + +#include "samsung.h" + +static int s3c2412_serial_setsource(struct uart_port *port, + struct s3c24xx_uart_clksrc *clk) +{ + unsigned long ucon = rd_regl(port, S3C2410_UCON); + + ucon &= ~S3C2412_UCON_CLKMASK; + + if (strcmp(clk->name, "uclk") == 0) + ucon |= S3C2440_UCON_UCLK; + else if (strcmp(clk->name, "pclk") == 0) + ucon |= S3C2440_UCON_PCLK; + else if (strcmp(clk->name, "usysclk") == 0) + ucon |= S3C2412_UCON_USYSCLK; + else { + printk(KERN_ERR "unknown clock source %s\n", clk->name); + return -EINVAL; + } + + wr_regl(port, S3C2410_UCON, ucon); + return 0; +} + + +static int s3c2412_serial_getsource(struct uart_port *port, + struct s3c24xx_uart_clksrc *clk) +{ + unsigned long ucon = rd_regl(port, S3C2410_UCON); + + switch (ucon & S3C2412_UCON_CLKMASK) { + case S3C2412_UCON_UCLK: + clk->divisor = 1; + clk->name = "uclk"; + break; + + case S3C2412_UCON_PCLK: + case S3C2412_UCON_PCLK2: + clk->divisor = 1; + clk->name = "pclk"; + break; + + case S3C2412_UCON_USYSCLK: + clk->divisor = 1; + clk->name = "usysclk"; + break; + } + + return 0; +} + +static int s3c2412_serial_resetport(struct uart_port *port, + struct s3c2410_uartcfg *cfg) +{ + unsigned long ucon = rd_regl(port, S3C2410_UCON); + + dbg("%s: port=%p (%08lx), cfg=%p\n", + __func__, port, port->mapbase, cfg); + + /* ensure we don't change the clock settings... */ + + ucon &= S3C2412_UCON_CLKMASK; + + wr_regl(port, S3C2410_UCON, ucon | cfg->ucon); + wr_regl(port, S3C2410_ULCON, cfg->ulcon); + + /* reset both fifos */ + + wr_regl(port, S3C2410_UFCON, cfg->ufcon | S3C2410_UFCON_RESETBOTH); + wr_regl(port, S3C2410_UFCON, cfg->ufcon); + + return 0; +} + +static struct s3c24xx_uart_info s3c2412_uart_inf = { + .name = "Samsung S3C2412 UART", + .type = PORT_S3C2412, + .fifosize = 64, + .rx_fifomask = S3C2440_UFSTAT_RXMASK, + .rx_fifoshift = S3C2440_UFSTAT_RXSHIFT, + .rx_fifofull = S3C2440_UFSTAT_RXFULL, + .tx_fifofull = S3C2440_UFSTAT_TXFULL, + .tx_fifomask = S3C2440_UFSTAT_TXMASK, + .tx_fifoshift = S3C2440_UFSTAT_TXSHIFT, + .get_clksrc = s3c2412_serial_getsource, + .set_clksrc = s3c2412_serial_setsource, + .reset_port = s3c2412_serial_resetport, +}; + +/* device management */ + +static int s3c2412_serial_probe(struct platform_device *dev) +{ + dbg("s3c2440_serial_probe: dev=%p\n", dev); + return s3c24xx_serial_probe(dev, &s3c2412_uart_inf); +} + +static struct platform_driver s3c2412_serial_drv = { + .probe = s3c2412_serial_probe, + .remove = s3c24xx_serial_remove, + .driver = { + .name = "s3c2412-uart", + .owner = THIS_MODULE, + }, +}; + +s3c24xx_console_init(&s3c2412_serial_drv, &s3c2412_uart_inf); + +static inline int s3c2412_serial_init(void) +{ + return s3c24xx_serial_init(&s3c2412_serial_drv, &s3c2412_uart_inf); +} + +static inline void s3c2412_serial_exit(void) +{ + platform_driver_unregister(&s3c2412_serial_drv); +} + +module_init(s3c2412_serial_init); +module_exit(s3c2412_serial_exit); + +MODULE_DESCRIPTION("Samsung S3C2412,S3C2413 SoC Serial port driver"); +MODULE_AUTHOR("Ben Dooks <ben@simtec.co.uk>"); +MODULE_LICENSE("GPL v2"); +MODULE_ALIAS("platform:s3c2412-uart"); diff --git a/drivers/serial/s3c2440.c b/drivers/serial/s3c2440.c new file mode 100644 index 00000000000..38f954bd39c --- /dev/null +++ b/drivers/serial/s3c2440.c @@ -0,0 +1,181 @@ +/* linux/drivers/serial/s3c2440.c + * + * Driver for Samsung S3C2440 and S3C2442 SoC onboard UARTs. + * + * Ben Dooks, Copyright (c) 2003-2005,2008 Simtec Electronics + * http://armlinux.simtec.co.uk/ + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. +*/ + +#include <linux/module.h> +#include <linux/ioport.h> +#include <linux/io.h> +#include <linux/platform_device.h> +#include <linux/init.h> +#include <linux/serial_core.h> +#include <linux/serial.h> + +#include <asm/irq.h> +#include <asm/hardware.h> + +#include <asm/plat-s3c/regs-serial.h> +#include <asm/arch/regs-gpio.h> + +#include "samsung.h" + + +static int s3c2440_serial_setsource(struct uart_port *port, + struct s3c24xx_uart_clksrc *clk) +{ + unsigned long ucon = rd_regl(port, S3C2410_UCON); + + /* todo - proper fclk<>nonfclk switch. */ + + ucon &= ~S3C2440_UCON_CLKMASK; + + if (strcmp(clk->name, "uclk") == 0) + ucon |= S3C2440_UCON_UCLK; + else if (strcmp(clk->name, "pclk") == 0) + ucon |= S3C2440_UCON_PCLK; + else if (strcmp(clk->name, "fclk") == 0) + ucon |= S3C2440_UCON_FCLK; + else { + printk(KERN_ERR "unknown clock source %s\n", clk->name); + return -EINVAL; + } + + wr_regl(port, S3C2410_UCON, ucon); + return 0; +} + + +static int s3c2440_serial_getsource(struct uart_port *port, + struct s3c24xx_uart_clksrc *clk) +{ + unsigned long ucon = rd_regl(port, S3C2410_UCON); + unsigned long ucon0, ucon1, ucon2; + + switch (ucon & S3C2440_UCON_CLKMASK) { + case S3C2440_UCON_UCLK: + clk->divisor = 1; + clk->name = "uclk"; + break; + + case S3C2440_UCON_PCLK: + case S3C2440_UCON_PCLK2: + clk->divisor = 1; + clk->name = "pclk"; + break; + + case S3C2440_UCON_FCLK: + /* the fun of calculating the uart divisors on + * the s3c2440 */ + + ucon0 = __raw_readl(S3C24XX_VA_UART0 + S3C2410_UCON); + ucon1 = __raw_readl(S3C24XX_VA_UART1 + S3C2410_UCON); + ucon2 = __raw_readl(S3C24XX_VA_UART2 + S3C2410_UCON); + + printk("ucons: %08lx, %08lx, %08lx\n", ucon0, ucon1, ucon2); + + ucon0 &= S3C2440_UCON0_DIVMASK; + ucon1 &= S3C2440_UCON1_DIVMASK; + ucon2 &= S3C2440_UCON2_DIVMASK; + + if (ucon0 != 0) { + clk->divisor = ucon0 >> S3C2440_UCON_DIVSHIFT; + clk->divisor += 6; + } else if (ucon1 != 0) { + clk->divisor = ucon1 >> S3C2440_UCON_DIVSHIFT; + clk->divisor += 21; + } else if (ucon2 != 0) { + clk->divisor = ucon2 >> S3C2440_UCON_DIVSHIFT; + clk->divisor += 36; + } else { + /* manual calims 44, seems to be 9 */ + clk->divisor = 9; + } + + clk->name = "fclk"; + break; + } + + return 0; +} + +static int s3c2440_serial_resetport(struct uart_port *port, + struct s3c2410_uartcfg *cfg) +{ + unsigned long ucon = rd_regl(port, S3C2410_UCON); + + dbg("s3c2440_serial_resetport: port=%p (%08lx), cfg=%p\n", + port, port->mapbase, cfg); + + /* ensure we don't change the clock settings... */ + + ucon &= (S3C2440_UCON0_DIVMASK | (3<<10)); + + wr_regl(port, S3C2410_UCON, ucon | cfg->ucon); + wr_regl(port, S3C2410_ULCON, cfg->ulcon); + + /* reset both fifos */ + + wr_regl(port, S3C2410_UFCON, cfg->ufcon | S3C2410_UFCON_RESETBOTH); + wr_regl(port, S3C2410_UFCON, cfg->ufcon); + + return 0; +} + +static struct s3c24xx_uart_info s3c2440_uart_inf = { + .name = "Samsung S3C2440 UART", + .type = PORT_S3C2440, + .fifosize = 64, + .rx_fifomask = S3C2440_UFSTAT_RXMASK, + .rx_fifoshift = S3C2440_UFSTAT_RXSHIFT, + .rx_fifofull = S3C2440_UFSTAT_RXFULL, + .tx_fifofull = S3C2440_UFSTAT_TXFULL, + .tx_fifomask = S3C2440_UFSTAT_TXMASK, + .tx_fifoshift = S3C2440_UFSTAT_TXSHIFT, + .get_clksrc = s3c2440_serial_getsource, + .set_clksrc = s3c2440_serial_setsource, + .reset_port = s3c2440_serial_resetport, +}; + +/* device management */ + +static int s3c2440_serial_probe(struct platform_device *dev) +{ + dbg("s3c2440_serial_probe: dev=%p\n", dev); + return s3c24xx_serial_probe(dev, &s3c2440_uart_inf); +} + +static struct platform_driver s3c2440_serial_drv = { + .probe = s3c2440_serial_probe, + .remove = s3c24xx_serial_remove, + .driver = { + .name = "s3c2440-uart", + .owner = THIS_MODULE, + }, +}; + +s3c24xx_console_init(&s3c2440_serial_drv, &s3c2440_uart_inf); + +static int __init s3c2440_serial_init(void) +{ + return s3c24xx_serial_init(&s3c2440_serial_drv, &s3c2440_uart_inf); +} + +static void __exit s3c2440_serial_exit(void) +{ + platform_driver_unregister(&s3c2440_serial_drv); +} + +module_init(s3c2440_serial_init); +module_exit(s3c2440_serial_exit); + +MODULE_DESCRIPTION("Samsung S3C2440,S3C2442 SoC Serial port driver"); +MODULE_AUTHOR("Ben Dooks <ben@simtec.co.uk>"); +MODULE_LICENSE("GPLi v2"); +MODULE_ALIAS("platform:s3c2440-uart"); diff --git a/drivers/serial/samsung.c b/drivers/serial/samsung.c new file mode 100644 index 00000000000..4a3ecaa629e --- /dev/null +++ b/drivers/serial/samsung.c @@ -0,0 +1,1317 @@ +/* linux/drivers/serial/samsuing.c + * + * Driver core for Samsung SoC onboard UARTs. + * + * Ben Dooks, Copyright (c) 2003-2005,2008 Simtec Electronics + * http://armlinux.simtec.co.uk/ + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. +*/ + +/* Hote on 2410 error handling + * + * The s3c2410 manual has a love/hate affair with the contents of the + * UERSTAT register in the UART blocks, and keeps marking some of the + * error bits as reserved. Having checked with the s3c2410x01, + * it copes with BREAKs properly, so I am happy to ignore the RESERVED + * feature from the latter versions of the manual. + * + * If it becomes aparrent that latter versions of the 2410 remove these + * bits, then action will have to be taken to differentiate the versions + * and change the policy on BREAK + * + * BJD, 04-Nov-2004 +*/ + +#if defined(CONFIG_SERIAL_SAMSUNG_CONSOLE) && defined(CONFIG_MAGIC_SYSRQ) +#define SUPPORT_SYSRQ +#endif + +#include <linux/module.h> +#include <linux/ioport.h> +#include <linux/io.h> +#include <linux/platform_device.h> +#include <linux/init.h> +#include <linux/sysrq.h> +#include <linux/console.h> +#include <linux/tty.h> +#include <linux/tty_flip.h> +#include <linux/serial_core.h> +#include <linux/serial.h> +#include <linux/delay.h> +#include <linux/clk.h> + +#include <asm/irq.h> + +#include <asm/hardware.h> + +#include <asm/plat-s3c/regs-serial.h> +#include <asm/arch/regs-gpio.h> + +#include "samsung.h" + +/* UART name and device definitions */ + +#define S3C24XX_SERIAL_NAME "ttySAC" +#define S3C24XX_SERIAL_MAJOR 204 +#define S3C24XX_SERIAL_MINOR 64 + +/* we can support 3 uarts, but not always use them */ + +#ifdef CONFIG_CPU_S3C2400 +#define NR_PORTS (2) +#else +#define NR_PORTS (3) +#endif + +/* port irq numbers */ + +#define TX_IRQ(port) ((port)->irq + 1) +#define RX_IRQ(port) ((port)->irq) + +/* macros to change one thing to another */ + +#define tx_enabled(port) ((port)->unused[0]) +#define rx_enabled(port) ((port)->unused[1]) + +/* flag to ignore all characters comming in */ +#define RXSTAT_DUMMY_READ (0x10000000) + +static inline struct s3c24xx_uart_port *to_ourport(struct uart_port *port) +{ + return container_of(port, struct s3c24xx_uart_port, port); +} + +/* translate a port to the device name */ + +static inline const char *s3c24xx_serial_portname(struct uart_port *port) +{ + return to_platform_device(port->dev)->name; +} + +static int s3c24xx_serial_txempty_nofifo(struct uart_port *port) +{ + return (rd_regl(port, S3C2410_UTRSTAT) & S3C2410_UTRSTAT_TXE); +} + +static void s3c24xx_serial_rx_enable(struct uart_port *port) +{ + unsigned long flags; + unsigned int ucon, ufcon; + int count = 10000; + + spin_lock_irqsave(&port->lock, flags); + + while (--count && !s3c24xx_serial_txempty_nofifo(port)) + udelay(100); + + ufcon = rd_regl(port, S3C2410_UFCON); + ufcon |= S3C2410_UFCON_RESETRX; + wr_regl(port, S3C2410_UFCON, ufcon); + + ucon = rd_regl(port, S3C2410_UCON); + ucon |= S3C2410_UCON_RXIRQMODE; + wr_regl(port, S3C2410_UCON, ucon); + + rx_enabled(port) = 1; + spin_unlock_irqrestore(&port->lock, flags); +} + +static void s3c24xx_serial_rx_disable(struct uart_port *port) +{ + unsigned long flags; + unsigned int ucon; + + spin_lock_irqsave(&port->lock, flags); + + ucon = rd_regl(port, S3C2410_UCON); + ucon &= ~S3C2410_UCON_RXIRQMODE; + wr_regl(port, S3C2410_UCON, ucon); + + rx_enabled(port) = 0; + spin_unlock_irqrestore(&port->lock, flags); +} + +static void s3c24xx_serial_stop_tx(struct uart_port *port) +{ + if (tx_enabled(port)) { + disable_irq(TX_IRQ(port)); + tx_enabled(port) = 0; + if (port->flags & UPF_CONS_FLOW) + s3c24xx_serial_rx_enable(port); + } +} + +static void s3c24xx_serial_start_tx(struct uart_port *port) +{ + if (!tx_enabled(port)) { + if (port->flags & UPF_CONS_FLOW) + s3c24xx_serial_rx_disable(port); + + enable_irq(TX_IRQ(port)); + tx_enabled(port) = 1; + } +} + + +static void s3c24xx_serial_stop_rx(struct uart_port *port) +{ + if (rx_enabled(port)) { + dbg("s3c24xx_serial_stop_rx: port=%p\n", port); + disable_irq(RX_IRQ(port)); + rx_enabled(port) = 0; + } +} + +static void s3c24xx_serial_enable_ms(struct uart_port *port) +{ +} + +static inline struct s3c24xx_uart_info *s3c24xx_port_to_info(struct uart_port *port) +{ + return to_ourport(port)->info; +} + +static inline struct s3c2410_uartcfg *s3c24xx_port_to_cfg(struct uart_port *port) +{ + if (port->dev == NULL) + return NULL; + + return (struct s3c2410_uartcfg *)port->dev->platform_data; +} + +static int s3c24xx_serial_rx_fifocnt(struct s3c24xx_uart_port *ourport, + unsigned long ufstat) +{ + struct s3c24xx_uart_info *info = ourport->info; + + if (ufstat & info->rx_fifofull) + return info->fifosize; + + return (ufstat & info->rx_fifomask) >> info->rx_fifoshift; +} + + +/* ? - where has parity gone?? */ +#define S3C2410_UERSTAT_PARITY (0x1000) + +static irqreturn_t +s3c24xx_serial_rx_chars(int irq, void *dev_id) +{ + struct s3c24xx_uart_port *ourport = dev_id; + struct uart_port *port = &ourport->port; + struct tty_struct *tty = port->info->tty; + unsigned int ufcon, ch, flag, ufstat, uerstat; + int max_count = 64; + + while (max_count-- > 0) { + ufcon = rd_regl(port, S3C2410_UFCON); + ufstat = rd_regl(port, S3C2410_UFSTAT); + + if (s3c24xx_serial_rx_fifocnt(ourport, ufstat) == 0) + break; + + uerstat = rd_regl(port, S3C2410_UERSTAT); + ch = rd_regb(port, S3C2410_URXH); + + if (port->flags & UPF_CONS_FLOW) { + int txe = s3c24xx_serial_txempty_nofifo(port); + + if (rx_enabled(port)) { + if (!txe) { + rx_enabled(port) = 0; + continue; + } + } else { + if (txe) { + ufcon |= S3C2410_UFCON_RESETRX; + wr_regl(port, S3C2410_UFCON, ufcon); + rx_enabled(port) = 1; + goto out; + } + continue; + } + } + + /* insert the character into the buffer */ + + flag = TTY_NORMAL; + port->icount.rx++; + + if (unlikely(uerstat & S3C2410_UERSTAT_ANY)) { + dbg("rxerr: port ch=0x%02x, rxs=0x%08x\n", + ch, uerstat); + + /* check for break */ + if (uerstat & S3C2410_UERSTAT_BREAK) { + dbg("break!\n"); + port->icount.brk++; + if (uart_handle_break(port)) + goto ignore_char; + } + + if (uerstat & S3C2410_UERSTAT_FRAME) + port->icount.frame++; + if (uerstat & S3C2410_UERSTAT_OVERRUN) + port->icount.overrun++; + + uerstat &= port->read_status_mask; + + if (uerstat & S3C2410_UERSTAT_BREAK) + flag = TTY_BREAK; + else if (uerstat & S3C2410_UERSTAT_PARITY) + flag = TTY_PARITY; + else if (uerstat & (S3C2410_UERSTAT_FRAME | + S3C2410_UERSTAT_OVERRUN)) + flag = TTY_FRAME; + } + + if (uart_handle_sysrq_char(port, ch)) + goto ignore_char; + + uart_insert_char(port, uerstat, S3C2410_UERSTAT_OVERRUN, + ch, flag); + + ignore_char: + continue; + } + tty_flip_buffer_push(tty); + + out: + return IRQ_HANDLED; +} + +static irqreturn_t s3c24xx_serial_tx_chars(int irq, void *id) +{ + struct s3c24xx_uart_port *ourport = id; + struct uart_port *port = &ourport->port; + struct circ_buf *xmit = &port->info->xmit; + int count = 256; + + if (port->x_char) { + wr_regb(port, S3C2410_UTXH, port->x_char); + port->icount.tx++; + port->x_char = 0; + goto out; + } + + /* if there isnt anything more to transmit, or the uart is now + * stopped, disable the uart and exit + */ + + if (uart_circ_empty(xmit) || uart_tx_stopped(port)) { + s3c24xx_serial_stop_tx(port); + goto out; + } + + /* try and drain the buffer... */ + + while (!uart_circ_empty(xmit) && count-- > 0) { + if (rd_regl(port, S3C2410_UFSTAT) & ourport->info->tx_fifofull) + break; + + wr_regb(port, S3C2410_UTXH, xmit->buf[xmit->tail]); + xmit->tail = (xmit->tail + 1) & (UART_XMIT_SIZE - 1); + port->icount.tx++; + } + + if (uart_circ_chars_pending(xmit) < WAKEUP_CHARS) + uart_write_wakeup(port); + + if (uart_circ_empty(xmit)) + s3c24xx_serial_stop_tx(port); + + out: + return IRQ_HANDLED; +} + +static unsigned int s3c24xx_serial_tx_empty(struct uart_port *port) +{ + struct s3c24xx_uart_info *info = s3c24xx_port_to_info(port); + unsigned long ufstat = rd_regl(port, S3C2410_UFSTAT); + unsigned long ufcon = rd_regl(port, S3C2410_UFCON); + + if (ufcon & S3C2410_UFCON_FIFOMODE) { + if ((ufstat & info->tx_fifomask) != 0 || + (ufstat & info->tx_fifofull)) + return 0; + + return 1; + } + + return s3c24xx_serial_txempty_nofifo(port); +} + +/* no modem control lines */ +static unsigned int s3c24xx_serial_get_mctrl(struct uart_port *port) +{ + unsigned int umstat = rd_regb(port, S3C2410_UMSTAT); + + if (umstat & S3C2410_UMSTAT_CTS) + return TIOCM_CAR | TIOCM_DSR | TIOCM_CTS; + else + return TIOCM_CAR | TIOCM_DSR; +} + +static void s3c24xx_serial_set_mctrl(struct uart_port *port, unsigned int mctrl) +{ + /* todo - possibly remove AFC and do manual CTS */ +} + +static void s3c24xx_serial_break_ctl(struct uart_port *port, int break_state) +{ + unsigned long flags; + unsigned int ucon; + + spin_lock_irqsave(&port->lock, flags); + + ucon = rd_regl(port, S3C2410_UCON); + + if (break_state) + ucon |= S3C2410_UCON_SBREAK; + else + ucon &= ~S3C2410_UCON_SBREAK; + + wr_regl(port, S3C2410_UCON, ucon); + + spin_unlock_irqrestore(&port->lock, flags); +} + +static void s3c24xx_serial_shutdown(struct uart_port *port) +{ + struct s3c24xx_uart_port *ourport = to_ourport(port); + + if (ourport->tx_claimed) { + free_irq(TX_IRQ(port), ourport); + tx_enabled(port) = 0; + ourport->tx_claimed = 0; + } + + if (ourport->rx_claimed) { + free_irq(RX_IRQ(port), ourport); + ourport->rx_claimed = 0; + rx_enabled(port) = 0; + } +} + + +static int s3c24xx_serial_startup(struct uart_port *port) +{ + struct s3c24xx_uart_port *ourport = to_ourport(port); + int ret; + + dbg("s3c24xx_serial_startup: port=%p (%08lx,%p)\n", + port->mapbase, port->membase); + + rx_enabled(port) = 1; + + ret = request_irq(RX_IRQ(port), + s3c24xx_serial_rx_chars, 0, + s3c24xx_serial_portname(port), ourport); + + if (ret != 0) { + printk(KERN_ERR "cannot get irq %d\n", RX_IRQ(port)); + return ret; + } + + ourport->rx_claimed = 1; + + dbg("requesting tx irq...\n"); + + tx_enabled(port) = 1; + + ret = request_irq(TX_IRQ(port), + s3c24xx_serial_tx_chars, 0, + s3c24xx_serial_portname(port), ourport); + + if (ret) { + printk(KERN_ERR "cannot get irq %d\n", TX_IRQ(port)); + goto err; + } + + ourport->tx_claimed = 1; + + dbg("s3c24xx_serial_startup ok\n"); + + /* the port reset code should have done the correct + * register setup for the port controls */ + + return ret; + + err: + s3c24xx_serial_shutdown(port); + return ret; +} + +/* power power management control */ + +static void s3c24xx_serial_pm(struct uart_port *port, unsigned int level, + unsigned int old) +{ + struct s3c24xx_uart_port *ourport = to_ourport(port); + + switch (level) { + case 3: + if (!IS_ERR(ourport->baudclk) && ourport->baudclk != NULL) + clk_disable(ourport->baudclk); + + clk_disable(ourport->clk); + break; + + case 0: + clk_enable(ourport->clk); + + if (!IS_ERR(ourport->baudclk) && ourport->baudclk != NULL) + clk_enable(ourport->baudclk); + + break; + default: + printk(KERN_ERR "s3c24xx_serial: unknown pm %d\n", level); + } +} + +/* baud rate calculation + * + * The UARTs on the S3C2410/S3C2440 can take their clocks from a number + * of different sources, including the peripheral clock ("pclk") and an + * external clock ("uclk"). The S3C2440 also adds the core clock ("fclk") + * with a programmable extra divisor. + * + * The following code goes through the clock sources, and calculates the + * baud clocks (and the resultant actual baud rates) and then tries to + * pick the closest one and select that. + * +*/ + + +#define MAX_CLKS (8) + +static struct s3c24xx_uart_clksrc tmp_clksrc = { + .name = "pclk", + .min_baud = 0, + .max_baud = 0, + .divisor = 1, +}; + +static inline int +s3c24xx_serial_getsource(struct uart_port *port, struct s3c24xx_uart_clksrc *c) +{ + struct s3c24xx_uart_info *info = s3c24xx_port_to_info(port); + + return (info->get_clksrc)(port, c); +} + +static inline int +s3c24xx_serial_setsource(struct uart_port *port, struct s3c24xx_uart_clksrc *c) +{ + struct s3c24xx_uart_info *info = s3c24xx_port_to_info(port); + + return (info->set_clksrc)(port, c); +} + +struct baud_calc { + struct s3c24xx_uart_clksrc *clksrc; + unsigned int calc; + unsigned int quot; + struct clk *src; +}; + +static int s3c24xx_serial_calcbaud(struct baud_calc *calc, + struct uart_port *port, + struct s3c24xx_uart_clksrc *clksrc, + unsigned int baud) +{ + unsigned long rate; + + calc->src = clk_get(port->dev, clksrc->name); + if (calc->src == NULL || IS_ERR(calc->src)) + return 0; + + rate = clk_get_rate(calc->src); + rate /= clksrc->divisor; + + calc->clksrc = clksrc; + calc->quot = (rate + (8 * baud)) / (16 * baud); + calc->calc = (rate / (calc->quot * 16)); + + calc->quot--; + return 1; +} + +static unsigned int s3c24xx_serial_getclk(struct uart_port *port, + struct s3c24xx_uart_clksrc **clksrc, + struct clk **clk, + unsigned int baud) +{ + struct s3c2410_uartcfg *cfg = s3c24xx_port_to_cfg(port); + struct s3c24xx_uart_clksrc *clkp; + struct baud_calc res[MAX_CLKS]; + struct baud_calc *resptr, *best, *sptr; + int i; + + clkp = cfg->clocks; + best = NULL; + + if (cfg->clocks_size < 2) { + if (cfg->clocks_size == 0) + clkp = &tmp_clksrc; + + /* check to see if we're sourcing fclk, and if so we're + * going to have to update the clock source + */ + + if (strcmp(clkp->name, "fclk") == 0) { + struct s3c24xx_uart_clksrc src; + + s3c24xx_serial_getsource(port, &src); + + /* check that the port already using fclk, and if + * not, then re-select fclk + */ + + if (strcmp(src.name, clkp->name) == 0) { + s3c24xx_serial_setsource(port, clkp); + s3c24xx_serial_getsource(port, &src); + } + + clkp->divisor = src.divisor; + } + + s3c24xx_serial_calcbaud(res, port, clkp, baud); + best = res; + resptr = best + 1; + } else { + resptr = res; + + for (i = 0; i < cfg->clocks_size; i++, clkp++) { + if (s3c24xx_serial_calcbaud(resptr, port, clkp, baud)) + resptr++; + } + } + + /* ok, we now need to select the best clock we found */ + + if (!best) { + unsigned int deviation = (1<<30)|((1<<30)-1); + int calc_deviation; + + for (sptr = res; sptr < resptr; sptr++) { + calc_deviation = baud - sptr->calc; + if (calc_deviation < 0) + calc_deviation = -calc_deviation; + + if (calc_deviation < deviation) { + best = sptr; + deviation = calc_deviation; + } + } + } + + /* store results to pass back */ + + *clksrc = best->clksrc; + *clk = best->src; + + return best->quot; +} + +static void s3c24xx_serial_set_termios(struct uart_port *port, + struct ktermios *termios, + struct ktermios *old) +{ + struct s3c2410_uartcfg *cfg = s3c24xx_port_to_cfg(port); + struct s3c24xx_uart_port *ourport = to_ourport(port); + struct s3c24xx_uart_clksrc *clksrc = NULL; + struct clk *clk = NULL; + unsigned long flags; + unsigned int baud, quot; + unsigned int ulcon; + unsigned int umcon; + + /* + * We don't support modem control lines. + */ + termios->c_cflag &= ~(HUPCL | CMSPAR); + termios->c_cflag |= CLOCAL; + + /* + * Ask the core to calculate the divisor for us. + */ + + baud = uart_get_baud_rate(port, termios, old, 0, 115200*8); + + if (baud == 38400 && (port->flags & UPF_SPD_MASK) == UPF_SPD_CUST) + quot = port->custom_divisor; + else + quot = s3c24xx_serial_getclk(port, &clksrc, &clk, baud); + + /* check to see if we need to change clock source */ + + if (ourport->clksrc != clksrc || ourport->baudclk != clk) { + s3c24xx_serial_setsource(port, clksrc); + + if (ourport->baudclk != NULL && !IS_ERR(ourport->baudclk)) { + clk_disable(ourport->baudclk); + ourport->baudclk = NULL; + } + + clk_enable(clk); + + ourport->clksrc = clksrc; + ourport->baudclk = clk; + } + + switch (termios->c_cflag & CSIZE) { + case CS5: + dbg("config: 5bits/char\n"); + ulcon = S3C2410_LCON_CS5; + break; + case CS6: + dbg("config: 6bits/char\n"); + ulcon = S3C2410_LCON_CS6; + break; + case CS7: + dbg("config: 7bits/char\n"); + ulcon = S3C2410_LCON_CS7; + break; + case CS8: + default: + dbg("config: 8bits/char\n"); + ulcon = S3C2410_LCON_CS8; + break; + } + + /* preserve original lcon IR settings */ + ulcon |= (cfg->ulcon & S3C2410_LCON_IRM); + + if (termios->c_cflag & CSTOPB) + ulcon |= S3C2410_LCON_STOPB; + + umcon = (termios->c_cflag & CRTSCTS) ? S3C2410_UMCOM_AFC : 0; + + if (termios->c_cflag & PARENB) { + if (termios->c_cflag & PARODD) + ulcon |= S3C2410_LCON_PODD; + else + ulcon |= S3C2410_LCON_PEVEN; + } else { + ulcon |= S3C2410_LCON_PNONE; + } + + spin_lock_irqsave(&port->lock, flags); + + dbg("setting ulcon to %08x, brddiv to %d\n", ulcon, quot); + + wr_regl(port, S3C2410_ULCON, ulcon); + wr_regl(port, S3C2410_UBRDIV, quot); + wr_regl(port, S3C2410_UMCON, umcon); + + dbg("uart: ulcon = 0x%08x, ucon = 0x%08x, ufcon = 0x%08x\n", + rd_regl(port, S3C2410_ULCON), + rd_regl(port, S3C2410_UCON), + rd_regl(port, S3C2410_UFCON)); + + /* + * Update the per-port timeout. + */ + uart_update_timeout(port, termios->c_cflag, baud); + + /* + * Which character status flags are we interested in? + */ + port->read_status_mask = S3C2410_UERSTAT_OVERRUN; + if (termios->c_iflag & INPCK) + port->read_status_mask |= S3C2410_UERSTAT_FRAME | S3C2410_UERSTAT_PARITY; + + /* + * Which character status flags should we ignore? + */ + port->ignore_status_mask = 0; + if (termios->c_iflag & IGNPAR) + port->ignore_status_mask |= S3C2410_UERSTAT_OVERRUN; + if (termios->c_iflag & IGNBRK && termios->c_iflag & IGNPAR) + port->ignore_status_mask |= S3C2410_UERSTAT_FRAME; + + /* + * Ignore all characters if CREAD is not set. + */ + if ((termios->c_cflag & CREAD) == 0) + port->ignore_status_mask |= RXSTAT_DUMMY_READ; + + spin_unlock_irqrestore(&port->lock, flags); +} + +static const char *s3c24xx_serial_type(struct uart_port *port) +{ + switch (port->type) { + case PORT_S3C2410: + return "S3C2410"; + case PORT_S3C2440: + return "S3C2440"; + case PORT_S3C2412: + return "S3C2412"; + default: + return NULL; + } +} + +#define MAP_SIZE (0x100) + +static void s3c24xx_serial_release_port(struct uart_port *port) +{ + release_mem_region(port->mapbase, MAP_SIZE); +} + +static int s3c24xx_serial_request_port(struct uart_port *port) +{ + const char *name = s3c24xx_serial_portname(port); + return request_mem_region(port->mapbase, MAP_SIZE, name) ? 0 : -EBUSY; +} + +static void s3c24xx_serial_config_port(struct uart_port *port, int flags) +{ + struct s3c24xx_uart_info *info = s3c24xx_port_to_info(port); + + if (flags & UART_CONFIG_TYPE && + s3c24xx_serial_request_port(port) == 0) + port->type = info->type; +} + +/* + * verify the new serial_struct (for TIOCSSERIAL). + */ +static int +s3c24xx_serial_verify_port(struct uart_port *port, struct serial_struct *ser) +{ + struct s3c24xx_uart_info *info = s3c24xx_port_to_info(port); + + if (ser->type != PORT_UNKNOWN && ser->type != info->type) + return -EINVAL; + + return 0; +} + + +#ifdef CONFIG_SERIAL_SAMSUNG_CONSOLE + +static struct console s3c24xx_serial_console; + +#define S3C24XX_SERIAL_CONSOLE &s3c24xx_serial_console +#else +#define S3C24XX_SERIAL_CONSOLE NULL +#endif + +static struct uart_ops s3c24xx_serial_ops = { + .pm = s3c24xx_serial_pm, + .tx_empty = s3c24xx_serial_tx_empty, + .get_mctrl = s3c24xx_serial_get_mctrl, + .set_mctrl = s3c24xx_serial_set_mctrl, + .stop_tx = s3c24xx_serial_stop_tx, + .start_tx = s3c24xx_serial_start_tx, + .stop_rx = s3c24xx_serial_stop_rx, + .enable_ms = s3c24xx_serial_enable_ms, + .break_ctl = s3c24xx_serial_break_ctl, + .startup = s3c24xx_serial_startup, + .shutdown = s3c24xx_serial_shutdown, + .set_termios = s3c24xx_serial_set_termios, + .type = s3c24xx_serial_type, + .release_port = s3c24xx_serial_release_port, + .request_port = s3c24xx_serial_request_port, + .config_port = s3c24xx_serial_config_port, + .verify_port = s3c24xx_serial_verify_port, +}; + + +static struct uart_driver s3c24xx_uart_drv = { + .owner = THIS_MODULE, + .dev_name = "s3c2410_serial", + .nr = 3, + .cons = S3C24XX_SERIAL_CONSOLE, + .driver_name = S3C24XX_SERIAL_NAME, + .major = S3C24XX_SERIAL_MAJOR, + .minor = S3C24XX_SERIAL_MINOR, +}; + +static struct s3c24xx_uart_port s3c24xx_serial_ports[NR_PORTS] = { + [0] = { + .port = { + .lock = __SPIN_LOCK_UNLOCKED(s3c24xx_serial_ports[0].port.lock), + .iotype = UPIO_MEM, + .irq = IRQ_S3CUART_RX0, + .uartclk = 0, + .fifosize = 16, + .ops = &s3c24xx_serial_ops, + .flags = UPF_BOOT_AUTOCONF, + .line = 0, + } + }, + [1] = { + .port = { + .lock = __SPIN_LOCK_UNLOCKED(s3c24xx_serial_ports[1].port.lock), + .iotype = UPIO_MEM, + .irq = IRQ_S3CUART_RX1, + .uartclk = 0, + .fifosize = 16, + .ops = &s3c24xx_serial_ops, + .flags = UPF_BOOT_AUTOCONF, + .line = 1, + } + }, +#if NR_PORTS > 2 + + [2] = { + .port = { + .lock = __SPIN_LOCK_UNLOCKED(s3c24xx_serial_ports[2].port.lock), + .iotype = UPIO_MEM, + .irq = IRQ_S3CUART_RX2, + .uartclk = 0, + .fifosize = 16, + .ops = &s3c24xx_serial_ops, + .flags = UPF_BOOT_AUTOCONF, + .line = 2, + } + } +#endif +}; + +/* s3c24xx_serial_resetport + * + * wrapper to call the specific reset for this port (reset the fifos + * and the settings) +*/ + +static inline int s3c24xx_serial_resetport(struct uart_port *port, + struct s3c2410_uartcfg *cfg) +{ + struct s3c24xx_uart_info *info = s3c24xx_port_to_info(port); + + return (info->reset_port)(port, cfg); +} + +/* s3c24xx_serial_init_port + * + * initialise a single serial port from the platform device given + */ + +static int s3c24xx_serial_init_port(struct s3c24xx_uart_port *ourport, + struct s3c24xx_uart_info *info, + struct platform_device *platdev) +{ + struct uart_port *port = &ourport->port; + struct s3c2410_uartcfg *cfg; + struct resource *res; + int ret; + + dbg("s3c24xx_serial_init_port: port=%p, platdev=%p\n", port, platdev); + + if (platdev == NULL) + return -ENODEV; + + cfg = s3c24xx_dev_to_cfg(&platdev->dev); + + if (port->mapbase != 0) + return 0; + + if (cfg->hwport > 3) + return -EINVAL; + + /* setup info for port */ + port->dev = &platdev->dev; + ourport->info = info; + + /* copy the info in from provided structure */ + ourport->port.fifosize = info->fifosize; + + dbg("s3c24xx_serial_init_port: %p (hw %d)...\n", port, cfg->hwport); + + port->uartclk = 1; + + if (cfg->uart_flags & UPF_CONS_FLOW) { + dbg("s3c24xx_serial_init_port: enabling flow control\n"); + port->flags |= UPF_CONS_FLOW; + } + + /* sort our the physical and virtual addresses for each UART */ + + res = platform_get_resource(platdev, IORESOURCE_MEM, 0); + if (res == NULL) { + printk(KERN_ERR "failed to find memory resource for uart\n"); + return -EINVAL; + } + + dbg("resource %p (%lx..%lx)\n", res, res->start, res->end); + + port->mapbase = res->start; + port->membase = S3C24XX_VA_UART + (res->start - S3C24XX_PA_UART); + ret = platform_get_irq(platdev, 0); + if (ret < 0) + port->irq = 0; + else + port->irq = ret; + + ourport->clk = clk_get(&platdev->dev, "uart"); + + dbg("port: map=%08x, mem=%08x, irq=%d, clock=%ld\n", + port->mapbase, port->membase, port->irq, port->uartclk); + + /* reset the fifos (and setup the uart) */ + s3c24xx_serial_resetport(port, cfg); + return 0; +} + +static ssize_t s3c24xx_serial_show_clksrc(struct device *dev, + struct device_attribute *attr, + char *buf) +{ + struct uart_port *port = s3c24xx_dev_to_port(dev); + struct s3c24xx_uart_port *ourport = to_ourport(port); + + return snprintf(buf, PAGE_SIZE, "* %s\n", ourport->clksrc->name); +} + +static DEVICE_ATTR(clock_source, S_IRUGO, s3c24xx_serial_show_clksrc, NULL); + +/* Device driver serial port probe */ + +static int probe_index; + +int s3c24xx_serial_probe(struct platform_device *dev, + struct s3c24xx_uart_info *info) +{ + struct s3c24xx_uart_port *ourport; + int ret; + + dbg("s3c24xx_serial_probe(%p, %p) %d\n", dev, info, probe_index); + + ourport = &s3c24xx_serial_ports[probe_index]; + probe_index++; + + dbg("%s: initialising port %p...\n", __func__, ourport); + + ret = s3c24xx_serial_init_port(ourport, info, dev); + if (ret < 0) + goto probe_err; + + dbg("%s: adding port\n", __func__); + uart_add_one_port(&s3c24xx_uart_drv, &ourport->port); + platform_set_drvdata(dev, &ourport->port); + + ret = device_create_file(&dev->dev, &dev_attr_clock_source); + if (ret < 0) + printk(KERN_ERR "%s: failed to add clksrc attr.\n", __func__); + + return 0; + + probe_err: + return ret; +} + +EXPORT_SYMBOL_GPL(s3c24xx_serial_probe); + +int s3c24xx_serial_remove(struct platform_device *dev) +{ + struct uart_port *port = s3c24xx_dev_to_port(&dev->dev); + + if (port) { + device_remove_file(&dev->dev, &dev_attr_clock_source); + uart_remove_one_port(&s3c24xx_uart_drv, port); + } + + return 0; +} + +EXPORT_SYMBOL_GPL(s3c24xx_serial_remove); + +/* UART power management code */ + +#ifdef CONFIG_PM + +static int s3c24xx_serial_suspend(struct platform_device *dev, pm_message_t state) +{ + struct uart_port *port = s3c24xx_dev_to_port(&dev->dev); + + if (port) + uart_suspend_port(&s3c24xx_uart_drv, port); + + return 0; +} + +static int s3c24xx_serial_resume(struct platform_device *dev) +{ + struct uart_port *port = s3c24xx_dev_to_port(&dev->dev); + struct s3c24xx_uart_port *ourport = to_ourport(port); + + if (port) { + clk_enable(ourport->clk); + s3c24xx_serial_resetport(port, s3c24xx_port_to_cfg(port)); + clk_disable(ourport->clk); + + uart_resume_port(&s3c24xx_uart_drv, port); + } + + return 0; +} +#endif + +int s3c24xx_serial_init(struct platform_driver *drv, + struct s3c24xx_uart_info *info) +{ + dbg("s3c24xx_serial_init(%p,%p)\n", drv, info); + +#ifdef CONFIG_PM + drv->suspend = s3c24xx_serial_suspend; + drv->resume = s3c24xx_serial_resume; +#endif + + return platform_driver_register(drv); +} + +EXPORT_SYMBOL_GPL(s3c24xx_serial_init); + +/* module initialisation code */ + +static int __init s3c24xx_serial_modinit(void) +{ + int ret; + + ret = uart_register_driver(&s3c24xx_uart_drv); + if (ret < 0) { + printk(KERN_ERR "failed to register UART driver\n"); + return -1; + } + + return 0; +} + +static void __exit s3c24xx_serial_modexit(void) +{ + uart_unregister_driver(&s3c24xx_uart_drv); +} + +module_init(s3c24xx_serial_modinit); +module_exit(s3c24xx_serial_modexit); + +/* Console code */ + +#ifdef CONFIG_SERIAL_SAMSUNG_CONSOLE + +static struct uart_port *cons_uart; + +static int +s3c24xx_serial_console_txrdy(struct uart_port *port, unsigned int ufcon) +{ + struct s3c24xx_uart_info *info = s3c24xx_port_to_info(port); + unsigned long ufstat, utrstat; + + if (ufcon & S3C2410_UFCON_FIFOMODE) { + /* fifo mode - check ammount of data in fifo registers... */ + + ufstat = rd_regl(port, S3C2410_UFSTAT); + return (ufstat & info->tx_fifofull) ? 0 : 1; + } + + /* in non-fifo mode, we go and use the tx buffer empty */ + + utrstat = rd_regl(port, S3C2410_UTRSTAT); + return (utrstat & S3C2410_UTRSTAT_TXE) ? 1 : 0; +} + +static void +s3c24xx_serial_console_putchar(struct uart_port *port, int ch) +{ + unsigned int ufcon = rd_regl(cons_uart, S3C2410_UFCON); + while (!s3c24xx_serial_console_txrdy(port, ufcon)) + barrier(); + wr_regb(cons_uart, S3C2410_UTXH, ch); +} + +static void +s3c24xx_serial_console_write(struct console *co, const char *s, + unsigned int count) +{ + uart_console_write(cons_uart, s, count, s3c24xx_serial_console_putchar); +} + +static void __init +s3c24xx_serial_get_options(struct uart_port *port, int *baud, + int *parity, int *bits) +{ + struct s3c24xx_uart_clksrc clksrc; + struct clk *clk; + unsigned int ulcon; + unsigned int ucon; + unsigned int ubrdiv; + unsigned long rate; + + ulcon = rd_regl(port, S3C2410_ULCON); + ucon = rd_regl(port, S3C2410_UCON); + ubrdiv = rd_regl(port, S3C2410_UBRDIV); + + dbg("s3c24xx_serial_get_options: port=%p\n" + "registers: ulcon=%08x, ucon=%08x, ubdriv=%08x\n", + port, ulcon, ucon, ubrdiv); + + if ((ucon & 0xf) != 0) { + /* consider the serial port configured if the tx/rx mode set */ + + switch (ulcon & S3C2410_LCON_CSMASK) { + case S3C2410_LCON_CS5: + *bits = 5; + break; + case S3C2410_LCON_CS6: + *bits = 6; + break; + case S3C2410_LCON_CS7: + *bits = 7; + break; + default: + case S3C2410_LCON_CS8: + *bits = 8; + break; + } + + switch (ulcon & S3C2410_LCON_PMASK) { + case S3C2410_LCON_PEVEN: + *parity = 'e'; + break; + + case S3C2410_LCON_PODD: + *parity = 'o'; + break; + + case S3C2410_LCON_PNONE: + default: + *parity = 'n'; + } + + /* now calculate the baud rate */ + + s3c24xx_serial_getsource(port, &clksrc); + + clk = clk_get(port->dev, clksrc.name); + if (!IS_ERR(clk) && clk != NULL) + rate = clk_get_rate(clk) / clksrc.divisor; + else + rate = 1; + + + *baud = rate / (16 * (ubrdiv + 1)); + dbg("calculated baud %d\n", *baud); + } + +} + +/* s3c24xx_serial_init_ports + * + * initialise the serial ports from the machine provided initialisation + * data. +*/ + +static int s3c24xx_serial_init_ports(struct s3c24xx_uart_info *info) +{ + struct s3c24xx_uart_port *ptr = s3c24xx_serial_ports; + struct platform_device **platdev_ptr; + int i; + + dbg("s3c24xx_serial_init_ports: initialising ports...\n"); + + platdev_ptr = s3c24xx_uart_devs; + + for (i = 0; i < NR_PORTS; i++, ptr++, platdev_ptr++) { + s3c24xx_serial_init_port(ptr, info, *platdev_ptr); + } + + return 0; +} + +static int __init +s3c24xx_serial_console_setup(struct console *co, char *options) +{ + struct uart_port *port; + int baud = 9600; + int bits = 8; + int parity = 'n'; + int flow = 'n'; + + dbg("s3c24xx_serial_console_setup: co=%p (%d), %s\n", + co, co->index, options); + + /* is this a valid port */ + + if (co->index == -1 || co->index >= NR_PORTS) + co->index = 0; + + port = &s3c24xx_serial_ports[co->index].port; + + /* is the port configured? */ + + if (port->mapbase == 0x0) { + co->index = 0; + port = &s3c24xx_serial_ports[co->index].port; + } + + cons_uart = port; + + dbg("s3c24xx_serial_console_setup: port=%p (%d)\n", port, co->index); + + /* + * Check whether an invalid uart number has been specified, and + * if so, search for the first available port that does have + * console support. + */ + if (options) + uart_parse_options(options, &baud, &parity, &bits, &flow); + else + s3c24xx_serial_get_options(port, &baud, &parity, &bits); + + dbg("s3c24xx_serial_console_setup: baud %d\n", baud); + + return uart_set_options(port, co, baud, parity, bits, flow); +} + +/* s3c24xx_serial_initconsole + * + * initialise the console from one of the uart drivers +*/ + +static struct console s3c24xx_serial_console = { + .name = S3C24XX_SERIAL_NAME, + .device = uart_console_device, + .flags = CON_PRINTBUFFER, + .index = -1, + .write = s3c24xx_serial_console_write, + .setup = s3c24xx_serial_console_setup +}; + +int s3c24xx_serial_initconsole(struct platform_driver *drv, + struct s3c24xx_uart_info *info) + +{ + struct platform_device *dev = s3c24xx_uart_devs[0]; + + dbg("s3c24xx_serial_initconsole\n"); + + /* select driver based on the cpu */ + + if (dev == NULL) { + printk(KERN_ERR "s3c24xx: no devices for console init\n"); + return 0; + } + + if (strcmp(dev->name, drv->driver.name) != 0) + return 0; + + s3c24xx_serial_console.data = &s3c24xx_uart_drv; + s3c24xx_serial_init_ports(info); + + register_console(&s3c24xx_serial_console); + return 0; +} + +#endif /* CONFIG_SERIAL_SAMSUNG_CONSOLE */ + +MODULE_DESCRIPTION("Samsung SoC Serial port driver"); +MODULE_AUTHOR("Ben Dooks <ben@simtec.co.uk>"); +MODULE_LICENSE("GPL v2"); diff --git a/drivers/serial/samsung.h b/drivers/serial/samsung.h new file mode 100644 index 00000000000..5c92ebbe7d9 --- /dev/null +++ b/drivers/serial/samsung.h @@ -0,0 +1,102 @@ +/* linux/drivers/serial/samsung.h + * + * Driver for Samsung SoC onboard UARTs. + * + * Ben Dooks, Copyright (c) 2003-2005,2008 Simtec Electronics + * http://armlinux.simtec.co.uk/ + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. +*/ + +struct s3c24xx_uart_info { + char *name; + unsigned int type; + unsigned int fifosize; + unsigned long rx_fifomask; + unsigned long rx_fifoshift; + unsigned long rx_fifofull; + unsigned long tx_fifomask; + unsigned long tx_fifoshift; + unsigned long tx_fifofull; + + /* clock source control */ + + int (*get_clksrc)(struct uart_port *, struct s3c24xx_uart_clksrc *clk); + int (*set_clksrc)(struct uart_port *, struct s3c24xx_uart_clksrc *clk); + + /* uart controls */ + int (*reset_port)(struct uart_port *, struct s3c2410_uartcfg *); +}; + +struct s3c24xx_uart_port { + unsigned char rx_claimed; + unsigned char tx_claimed; + + struct s3c24xx_uart_info *info; + struct s3c24xx_uart_clksrc *clksrc; + struct clk *clk; + struct clk *baudclk; + struct uart_port port; +}; + +/* conversion functions */ + +#define s3c24xx_dev_to_port(__dev) (struct uart_port *)dev_get_drvdata(__dev) +#define s3c24xx_dev_to_cfg(__dev) (struct s3c2410_uartcfg *)((__dev)->platform_data) + +/* register access controls */ + +#define portaddr(port, reg) ((port)->membase + (reg)) + +#define rd_regb(port, reg) (__raw_readb(portaddr(port, reg))) +#define rd_regl(port, reg) (__raw_readl(portaddr(port, reg))) + +#define wr_regb(port, reg, val) __raw_writeb(val, portaddr(port, reg)) +#define wr_regl(port, reg, val) __raw_writel(val, portaddr(port, reg)) + +extern int s3c24xx_serial_probe(struct platform_device *dev, + struct s3c24xx_uart_info *uart); + +extern int s3c24xx_serial_remove(struct platform_device *dev); + +extern int s3c24xx_serial_initconsole(struct platform_driver *drv, + struct s3c24xx_uart_info *uart); + +extern int s3c24xx_serial_init(struct platform_driver *drv, + struct s3c24xx_uart_info *info); + +#ifdef CONFIG_SERIAL_SAMSUNG_CONSOLE + +#define s3c24xx_console_init(__drv, __inf) \ +static int __init s3c_serial_console_init(void) \ +{ \ + return s3c24xx_serial_initconsole(__drv, __inf); \ +} \ + \ +console_initcall(s3c_serial_console_init) + +#else +#define s3c24xx_console_init(drv, inf) extern void no_console(void) +#endif + +#ifdef CONFIG_SERIAL_SAMSUNG_DEBUG + +extern void printascii(const char *); + +static void dbg(const char *fmt, ...) +{ + va_list va; + char buff[256]; + + va_start(va, fmt); + vsprintf(buff, fmt, va); + va_end(va); + + printascii(buff); +} + +#else +#define dbg(x...) do { } while (0) +#endif diff --git a/drivers/spi/spi_imx.c b/drivers/spi/spi_imx.c index bd0729b6b6e..54ac7bea5f8 100644 --- a/drivers/spi/spi_imx.c +++ b/drivers/spi/spi_imx.c @@ -1538,24 +1538,24 @@ static int __init spi_imx_probe(struct platform_device *pdev) drv_data->rx_channel = -1; if (platform_info->enable_dma) { /* Get rx DMA channel */ - status = imx_dma_request_by_prio(&drv_data->rx_channel, - "spi_imx_rx", DMA_PRIO_HIGH); - if (status < 0) { + drv_data->rx_channel = imx_dma_request_by_prio("spi_imx_rx", + DMA_PRIO_HIGH); + if (drv_data->rx_channel < 0) { dev_err(dev, "probe - problem (%d) requesting rx channel\n", - status); + drv_data->rx_channel); goto err_no_rxdma; } else imx_dma_setup_handlers(drv_data->rx_channel, NULL, dma_err_handler, drv_data); /* Get tx DMA channel */ - status = imx_dma_request_by_prio(&drv_data->tx_channel, - "spi_imx_tx", DMA_PRIO_MEDIUM); - if (status < 0) { + drv_data->tx_channel = imx_dma_request_by_prio("spi_imx_tx", + DMA_PRIO_MEDIUM); + if (drv_data->tx_channel < 0) { dev_err(dev, "probe - problem (%d) requesting tx channel\n", - status); + drv_data->tx_channel); imx_dma_free(drv_data->rx_channel); goto err_no_txdma; } else diff --git a/drivers/usb/gadget/Kconfig b/drivers/usb/gadget/Kconfig index 6e784d2db42..3565d435282 100644 --- a/drivers/usb/gadget/Kconfig +++ b/drivers/usb/gadget/Kconfig @@ -118,10 +118,10 @@ config USB_AMD5536UDC config USB_GADGET_ATMEL_USBA boolean "Atmel USBA" select USB_GADGET_DUALSPEED - depends on AVR32 || ARCH_AT91CAP9 + depends on AVR32 || ARCH_AT91CAP9 || ARCH_AT91SAM9RL help USBA is the integrated high-speed USB Device controller on - the AT32AP700x and AT91CAP9 processors from Atmel. + the AT32AP700x, some AT91SAM9 and AT91CAP9 processors from Atmel. config USB_ATMEL_USBA tristate diff --git a/drivers/usb/gadget/at91_udc.c b/drivers/usb/gadget/at91_udc.c index 274c60a970c..b6b2a0a5ba3 100644 --- a/drivers/usb/gadget/at91_udc.c +++ b/drivers/usb/gadget/at91_udc.c @@ -888,7 +888,7 @@ static void pullup(struct at91_udc *udc, int is_on) at91_udp_write(udc, AT91_UDP_TXVC, 0); if (cpu_is_at91rm9200()) gpio_set_value(udc->board.pullup_pin, active); - else if (cpu_is_at91sam9260() || cpu_is_at91sam9263()) { + else if (cpu_is_at91sam9260() || cpu_is_at91sam9263() || cpu_is_at91sam9g20()) { u32 txvc = at91_udp_read(udc, AT91_UDP_TXVC); txvc |= AT91_UDP_TXVC_PUON; @@ -906,7 +906,7 @@ static void pullup(struct at91_udc *udc, int is_on) at91_udp_write(udc, AT91_UDP_TXVC, AT91_UDP_TXVC_TXVDIS); if (cpu_is_at91rm9200()) gpio_set_value(udc->board.pullup_pin, !active); - else if (cpu_is_at91sam9260() || cpu_is_at91sam9263()) { + else if (cpu_is_at91sam9260() || cpu_is_at91sam9263() || cpu_is_at91sam9g20()) { u32 txvc = at91_udp_read(udc, AT91_UDP_TXVC); txvc &= ~AT91_UDP_TXVC_PUON; diff --git a/drivers/usb/gadget/omap_udc.c b/drivers/usb/gadget/omap_udc.c index 881d74c3d96..03a7f49d207 100644 --- a/drivers/usb/gadget/omap_udc.c +++ b/drivers/usb/gadget/omap_udc.c @@ -135,13 +135,17 @@ static void use_ep(struct omap_ep *ep, u16 select) if (ep->bEndpointAddress & USB_DIR_IN) num |= UDC_EP_DIR; - UDC_EP_NUM_REG = num | select; + omap_writew(num | select, UDC_EP_NUM); /* when select, MUST deselect later !! */ } static inline void deselect_ep(void) { - UDC_EP_NUM_REG &= ~UDC_EP_SEL; + u16 w; + + w = omap_readw(UDC_EP_NUM); + w &= ~UDC_EP_SEL; + omap_writew(w, UDC_EP_NUM); /* 6 wait states before TX will happen */ } @@ -216,7 +220,7 @@ static int omap_ep_enable(struct usb_ep *_ep, ep->has_dma = 0; ep->lch = -1; use_ep(ep, UDC_EP_SEL); - UDC_CTRL_REG = udc->clr_halt; + omap_writew(udc->clr_halt, UDC_CTRL); ep->ackwait = 0; deselect_ep(); @@ -232,7 +236,7 @@ static int omap_ep_enable(struct usb_ep *_ep, if (desc->bmAttributes != USB_ENDPOINT_XFER_ISOC && !ep->has_dma && !(ep->bEndpointAddress & USB_DIR_IN)) { - UDC_CTRL_REG = UDC_SET_FIFO_EN; + omap_writew(UDC_SET_FIFO_EN, UDC_CTRL); ep->ackwait = 1 + ep->double_buf; } @@ -259,7 +263,7 @@ static int omap_ep_disable(struct usb_ep *_ep) nuke (ep, -ESHUTDOWN); ep->ep.maxpacket = ep->maxpacket; ep->has_dma = 0; - UDC_CTRL_REG = UDC_SET_HALT; + omap_writew(UDC_SET_HALT, UDC_CTRL); list_del_init(&ep->iso); del_timer(&ep->timer); @@ -360,13 +364,13 @@ write_packet(u8 *buf, struct omap_req *req, unsigned max) if (likely((((int)buf) & 1) == 0)) { wp = (u16 *)buf; while (max >= 2) { - UDC_DATA_REG = *wp++; + omap_writew(*wp++, UDC_DATA); max -= 2; } buf = (u8 *)wp; } while (max--) - *(volatile u8 *)&UDC_DATA_REG = *buf++; + omap_writeb(*buf++, UDC_DATA); return len; } @@ -385,13 +389,13 @@ static int write_fifo(struct omap_ep *ep, struct omap_req *req) prefetch(buf); /* PIO-IN isn't double buffered except for iso */ - ep_stat = UDC_STAT_FLG_REG; + ep_stat = omap_readw(UDC_STAT_FLG); if (ep_stat & UDC_FIFO_UNWRITABLE) return 0; count = ep->ep.maxpacket; count = write_packet(buf, req, count); - UDC_CTRL_REG = UDC_SET_FIFO_EN; + omap_writew(UDC_SET_FIFO_EN, UDC_CTRL); ep->ackwait = 1; /* last packet is often short (sometimes a zlp) */ @@ -425,13 +429,13 @@ read_packet(u8 *buf, struct omap_req *req, unsigned avail) if (likely((((int)buf) & 1) == 0)) { wp = (u16 *)buf; while (avail >= 2) { - *wp++ = UDC_DATA_REG; + *wp++ = omap_readw(UDC_DATA); avail -= 2; } buf = (u8 *)wp; } while (avail--) - *buf++ = *(volatile u8 *)&UDC_DATA_REG; + *buf++ = omap_readb(UDC_DATA); return len; } @@ -446,7 +450,7 @@ static int read_fifo(struct omap_ep *ep, struct omap_req *req) prefetchw(buf); for (;;) { - u16 ep_stat = UDC_STAT_FLG_REG; + u16 ep_stat = omap_readw(UDC_STAT_FLG); is_last = 0; if (ep_stat & FIFO_EMPTY) { @@ -460,7 +464,7 @@ static int read_fifo(struct omap_ep *ep, struct omap_req *req) if (ep_stat & UDC_FIFO_FULL) avail = ep->ep.maxpacket; else { - avail = UDC_RXFSTAT_REG; + avail = omap_readw(UDC_RXFSTAT); ep->fnf = ep->double_buf; } count = read_packet(buf, req, avail); @@ -473,7 +477,7 @@ static int read_fifo(struct omap_ep *ep, struct omap_req *req) req->req.status = -EOVERFLOW; avail -= count; while (avail--) - (void) *(volatile u8 *)&UDC_DATA_REG; + omap_readw(UDC_DATA); } } else if (req->req.length == req->req.actual) is_last = 1; @@ -491,32 +495,6 @@ static int read_fifo(struct omap_ep *ep, struct omap_req *req) /*-------------------------------------------------------------------------*/ -static inline dma_addr_t dma_csac(unsigned lch) -{ - dma_addr_t csac; - - /* omap 3.2/3.3 erratum: sometimes 0 is returned if CSAC/CDAC is - * read before the DMA controller finished disabling the channel. - */ - csac = OMAP_DMA_CSAC_REG(lch); - if (csac == 0) - csac = OMAP_DMA_CSAC_REG(lch); - return csac; -} - -static inline dma_addr_t dma_cdac(unsigned lch) -{ - dma_addr_t cdac; - - /* omap 3.2/3.3 erratum: sometimes 0 is returned if CSAC/CDAC is - * read before the DMA controller finished disabling the channel. - */ - cdac = OMAP_DMA_CDAC_REG(lch); - if (cdac == 0) - cdac = OMAP_DMA_CDAC_REG(lch); - return cdac; -} - static u16 dma_src_len(struct omap_ep *ep, dma_addr_t start) { dma_addr_t end; @@ -527,7 +505,7 @@ static u16 dma_src_len(struct omap_ep *ep, dma_addr_t start) if (cpu_is_omap15xx()) return 0; - end = dma_csac(ep->lch); + end = omap_get_dma_src_pos(ep->lch); if (end == ep->dma_counter) return 0; @@ -537,15 +515,11 @@ static u16 dma_src_len(struct omap_ep *ep, dma_addr_t start) return end - start; } -#define DMA_DEST_LAST(x) (cpu_is_omap15xx() \ - ? OMAP_DMA_CSAC_REG(x) /* really: CPC */ \ - : dma_cdac(x)) - static u16 dma_dest_len(struct omap_ep *ep, dma_addr_t start) { dma_addr_t end; - end = DMA_DEST_LAST(ep->lch); + end = omap_get_dma_dst_pos(ep->lch); if (end == ep->dma_counter) return 0; @@ -565,7 +539,7 @@ static u16 dma_dest_len(struct omap_ep *ep, dma_addr_t start) static void next_in_dma(struct omap_ep *ep, struct omap_req *req) { - u16 txdma_ctrl; + u16 txdma_ctrl, w; unsigned length = req->req.length - req->req.actual; const int sync_mode = cpu_is_omap15xx() ? OMAP_DMA_SYNC_FRAME @@ -596,14 +570,18 @@ static void next_in_dma(struct omap_ep *ep, struct omap_req *req) 0, 0); omap_start_dma(ep->lch); - ep->dma_counter = dma_csac(ep->lch); - UDC_DMA_IRQ_EN_REG |= UDC_TX_DONE_IE(ep->dma_channel); - UDC_TXDMA_REG(ep->dma_channel) = UDC_TXN_START | txdma_ctrl; + ep->dma_counter = omap_get_dma_src_pos(ep->lch); + w = omap_readw(UDC_DMA_IRQ_EN); + w |= UDC_TX_DONE_IE(ep->dma_channel); + omap_writew(w, UDC_DMA_IRQ_EN); + omap_writew(UDC_TXN_START | txdma_ctrl, UDC_TXDMA(ep->dma_channel)); req->dma_bytes = length; } static void finish_in_dma(struct omap_ep *ep, struct omap_req *req, int status) { + u16 w; + if (status == 0) { req->req.actual += req->dma_bytes; @@ -620,7 +598,9 @@ static void finish_in_dma(struct omap_ep *ep, struct omap_req *req, int status) /* tx completion */ omap_stop_dma(ep->lch); - UDC_DMA_IRQ_EN_REG &= ~UDC_TX_DONE_IE(ep->dma_channel); + w = omap_readw(UDC_DMA_IRQ_EN); + w &= ~UDC_TX_DONE_IE(ep->dma_channel); + omap_writew(w, UDC_DMA_IRQ_EN); done(ep, req, status); } @@ -628,6 +608,7 @@ static void next_out_dma(struct omap_ep *ep, struct omap_req *req) { unsigned packets = req->req.length - req->req.actual; int dma_trigger = 0; + u16 w; if (cpu_is_omap24xx()) dma_trigger = OMAP24XX_DMA(USB_W2FC_RX0, ep->dma_channel); @@ -654,12 +635,14 @@ static void next_out_dma(struct omap_ep *ep, struct omap_req *req) omap_set_dma_dest_params(ep->lch, OMAP_DMA_PORT_EMIFF, OMAP_DMA_AMODE_POST_INC, req->req.dma + req->req.actual, 0, 0); - ep->dma_counter = DMA_DEST_LAST(ep->lch); + ep->dma_counter = omap_get_dma_dst_pos(ep->lch); - UDC_RXDMA_REG(ep->dma_channel) = UDC_RXN_STOP | (packets - 1); - UDC_DMA_IRQ_EN_REG |= UDC_RX_EOT_IE(ep->dma_channel); - UDC_EP_NUM_REG = (ep->bEndpointAddress & 0xf); - UDC_CTRL_REG = UDC_SET_FIFO_EN; + omap_writew(UDC_RXN_STOP | (packets - 1), UDC_RXDMA(ep->dma_channel)); + w = omap_readw(UDC_DMA_IRQ_EN); + w |= UDC_RX_EOT_IE(ep->dma_channel); + omap_writew(w, UDC_DMA_IRQ_EN); + omap_writew(ep->bEndpointAddress & 0xf, UDC_EP_NUM); + omap_writew(UDC_SET_FIFO_EN, UDC_CTRL); omap_start_dma(ep->lch); } @@ -667,7 +650,7 @@ static void next_out_dma(struct omap_ep *ep, struct omap_req *req) static void finish_out_dma(struct omap_ep *ep, struct omap_req *req, int status, int one) { - u16 count; + u16 count, w; if (status == 0) ep->dma_counter = (u16) (req->req.dma + req->req.actual); @@ -686,13 +669,15 @@ finish_out_dma(struct omap_ep *ep, struct omap_req *req, int status, int one) return; /* rx completion */ - UDC_DMA_IRQ_EN_REG &= ~UDC_RX_EOT_IE(ep->dma_channel); + w = omap_readw(UDC_DMA_IRQ_EN); + w &= ~UDC_RX_EOT_IE(ep->dma_channel); + omap_writew(w, UDC_DMA_IRQ_EN); done(ep, req, status); } static void dma_irq(struct omap_udc *udc, u16 irq_src) { - u16 dman_stat = UDC_DMAN_STAT_REG; + u16 dman_stat = omap_readw(UDC_DMAN_STAT); struct omap_ep *ep; struct omap_req *req; @@ -706,7 +691,7 @@ static void dma_irq(struct omap_udc *udc, u16 irq_src) struct omap_req, queue); finish_in_dma(ep, req, 0); } - UDC_IRQ_SRC_REG = UDC_TXN_DONE; + omap_writew(UDC_TXN_DONE, UDC_IRQ_SRC); if (!list_empty (&ep->queue)) { req = container_of(ep->queue.next, @@ -725,7 +710,7 @@ static void dma_irq(struct omap_udc *udc, u16 irq_src) struct omap_req, queue); finish_out_dma(ep, req, 0, dman_stat & UDC_DMA_RX_SB); } - UDC_IRQ_SRC_REG = UDC_RXN_EOT; + omap_writew(UDC_RXN_EOT, UDC_IRQ_SRC); if (!list_empty (&ep->queue)) { req = container_of(ep->queue.next, @@ -739,7 +724,7 @@ static void dma_irq(struct omap_udc *udc, u16 irq_src) ep->irqs++; /* omap15xx does this unasked... */ VDBG("%s, RX_CNT irq?\n", ep->ep.name); - UDC_IRQ_SRC_REG = UDC_RXN_CNT; + omap_writew(UDC_RXN_CNT, UDC_IRQ_SRC); } } @@ -762,9 +747,9 @@ static void dma_channel_claim(struct omap_ep *ep, unsigned channel) is_in = ep->bEndpointAddress & USB_DIR_IN; if (is_in) - reg = UDC_TXDMA_CFG_REG; + reg = omap_readw(UDC_TXDMA_CFG); else - reg = UDC_RXDMA_CFG_REG; + reg = omap_readw(UDC_RXDMA_CFG); reg |= UDC_DMA_REQ; /* "pulse" activated */ ep->dma_channel = 0; @@ -792,7 +777,7 @@ static void dma_channel_claim(struct omap_ep *ep, unsigned channel) status = omap_request_dma(dma_channel, ep->ep.name, dma_error, ep, &ep->lch); if (status == 0) { - UDC_TXDMA_CFG_REG = reg; + omap_writew(reg, UDC_TXDMA_CFG); /* EMIFF or SDRC */ omap_set_dma_src_burst_mode(ep->lch, OMAP_DMA_DATA_BURST_4); @@ -801,7 +786,7 @@ static void dma_channel_claim(struct omap_ep *ep, unsigned channel) omap_set_dma_dest_params(ep->lch, OMAP_DMA_PORT_TIPB, OMAP_DMA_AMODE_CONSTANT, - (unsigned long) io_v2p((u32)&UDC_DATA_DMA_REG), + (unsigned long) io_v2p(UDC_DATA_DMA), 0, 0); } } else { @@ -813,12 +798,12 @@ static void dma_channel_claim(struct omap_ep *ep, unsigned channel) status = omap_request_dma(dma_channel, ep->ep.name, dma_error, ep, &ep->lch); if (status == 0) { - UDC_RXDMA_CFG_REG = reg; + omap_writew(reg, UDC_RXDMA_CFG); /* TIPB */ omap_set_dma_src_params(ep->lch, OMAP_DMA_PORT_TIPB, OMAP_DMA_AMODE_CONSTANT, - (unsigned long) io_v2p((u32)&UDC_DATA_DMA_REG), + (unsigned long) io_v2p(UDC_DATA_DMA), 0, 0); /* EMIFF or SDRC */ omap_set_dma_dest_burst_mode(ep->lch, @@ -834,7 +819,7 @@ static void dma_channel_claim(struct omap_ep *ep, unsigned channel) /* channel type P: hw synch (fifo) */ if (cpu_class_is_omap1() && !cpu_is_omap15xx()) - OMAP1_DMA_LCH_CTRL_REG(ep->lch) = 2; + omap_set_dma_channel_mode(ep->lch, OMAP_DMA_LCH_P); } just_restart: @@ -860,7 +845,7 @@ just_restart: (is_in ? write_fifo : read_fifo)(ep, req); deselect_ep(); if (!is_in) { - UDC_CTRL_REG = UDC_SET_FIFO_EN; + omap_writew(UDC_SET_FIFO_EN, UDC_CTRL); ep->ackwait = 1 + ep->double_buf; } /* IN: 6 wait states before it'll tx */ @@ -881,7 +866,7 @@ static void dma_channel_release(struct omap_ep *ep) else req = NULL; - active = ((1 << 7) & OMAP_DMA_CCR_REG(ep->lch)) != 0; + active = omap_get_dma_active_status(ep->lch); DBG("%s release %s %cxdma%d %p\n", ep->ep.name, active ? "active" : "idle", @@ -894,23 +879,25 @@ static void dma_channel_release(struct omap_ep *ep) /* wait till current packet DMA finishes, and fifo empties */ if (ep->bEndpointAddress & USB_DIR_IN) { - UDC_TXDMA_CFG_REG = (UDC_TXDMA_CFG_REG & ~mask) | UDC_DMA_REQ; + omap_writew((omap_readw(UDC_TXDMA_CFG) & ~mask) | UDC_DMA_REQ, + UDC_TXDMA_CFG); if (req) { finish_in_dma(ep, req, -ECONNRESET); /* clear FIFO; hosts probably won't empty it */ use_ep(ep, UDC_EP_SEL); - UDC_CTRL_REG = UDC_CLR_EP; + omap_writew(UDC_CLR_EP, UDC_CTRL); deselect_ep(); } - while (UDC_TXDMA_CFG_REG & mask) + while (omap_readw(UDC_TXDMA_CFG) & mask) udelay(10); } else { - UDC_RXDMA_CFG_REG = (UDC_RXDMA_CFG_REG & ~mask) | UDC_DMA_REQ; + omap_writew((omap_readw(UDC_RXDMA_CFG) & ~mask) | UDC_DMA_REQ, + UDC_RXDMA_CFG); /* dma empties the fifo */ - while (UDC_RXDMA_CFG_REG & mask) + while (omap_readw(UDC_RXDMA_CFG) & mask) udelay(10); if (req) finish_out_dma(ep, req, -ECONNRESET, 0); @@ -997,9 +984,13 @@ omap_ep_queue(struct usb_ep *_ep, struct usb_request *_req, gfp_t gfp_flags) req->req.actual = 0; /* maybe kickstart non-iso i/o queues */ - if (is_iso) - UDC_IRQ_EN_REG |= UDC_SOF_IE; - else if (list_empty(&ep->queue) && !ep->stopped && !ep->ackwait) { + if (is_iso) { + u16 w; + + w = omap_readw(UDC_IRQ_EN); + w |= UDC_SOF_IE; + omap_writew(w, UDC_IRQ_EN); + } else if (list_empty(&ep->queue) && !ep->stopped && !ep->ackwait) { int is_in; if (ep->bEndpointAddress == 0) { @@ -1017,23 +1008,23 @@ omap_ep_queue(struct usb_ep *_ep, struct usb_request *_req, gfp_t gfp_flags) * requests to non-control endpoints */ if (udc->ep0_set_config) { - u16 irq_en = UDC_IRQ_EN_REG; + u16 irq_en = omap_readw(UDC_IRQ_EN); irq_en |= UDC_DS_CHG_IE | UDC_EP0_IE; if (!udc->ep0_reset_config) irq_en |= UDC_EPN_RX_IE | UDC_EPN_TX_IE; - UDC_IRQ_EN_REG = irq_en; + omap_writew(irq_en, UDC_IRQ_EN); } /* STATUS for zero length DATA stages is * always an IN ... even for IN transfers, * a weird case which seem to stall OMAP. */ - UDC_EP_NUM_REG = (UDC_EP_SEL|UDC_EP_DIR); - UDC_CTRL_REG = UDC_CLR_EP; - UDC_CTRL_REG = UDC_SET_FIFO_EN; - UDC_EP_NUM_REG = UDC_EP_DIR; + omap_writew(UDC_EP_SEL | UDC_EP_DIR, UDC_EP_NUM); + omap_writew(UDC_CLR_EP, UDC_CTRL); + omap_writew(UDC_SET_FIFO_EN, UDC_CTRL); + omap_writew(UDC_EP_DIR, UDC_EP_NUM); /* cleanup */ udc->ep0_pending = 0; @@ -1042,11 +1033,11 @@ omap_ep_queue(struct usb_ep *_ep, struct usb_request *_req, gfp_t gfp_flags) /* non-empty DATA stage */ } else if (is_in) { - UDC_EP_NUM_REG = UDC_EP_SEL|UDC_EP_DIR; + omap_writew(UDC_EP_SEL | UDC_EP_DIR, UDC_EP_NUM); } else { if (udc->ep0_setup) goto irq_wait; - UDC_EP_NUM_REG = UDC_EP_SEL; + omap_writew(UDC_EP_SEL, UDC_EP_NUM); } } else { is_in = ep->bEndpointAddress & USB_DIR_IN; @@ -1062,7 +1053,7 @@ omap_ep_queue(struct usb_ep *_ep, struct usb_request *_req, gfp_t gfp_flags) req = NULL; deselect_ep(); if (!is_in) { - UDC_CTRL_REG = UDC_SET_FIFO_EN; + omap_writew(UDC_SET_FIFO_EN, UDC_CTRL); ep->ackwait = 1 + ep->double_buf; } /* IN: 6 wait states before it'll tx */ @@ -1130,9 +1121,9 @@ static int omap_ep_set_halt(struct usb_ep *_ep, int value) else if (value) { if (ep->udc->ep0_set_config) { WARN("error changing config?\n"); - UDC_SYSCON2_REG = UDC_CLR_CFG; + omap_writew(UDC_CLR_CFG, UDC_SYSCON2); } - UDC_SYSCON2_REG = UDC_STALL_CMD; + omap_writew(UDC_STALL_CMD, UDC_SYSCON2); ep->udc->ep0_pending = 0; status = 0; } else /* NOP */ @@ -1159,8 +1150,8 @@ static int omap_ep_set_halt(struct usb_ep *_ep, int value) channel = 0; use_ep(ep, UDC_EP_SEL); - if (UDC_STAT_FLG_REG & UDC_NON_ISO_FIFO_EMPTY) { - UDC_CTRL_REG = UDC_SET_HALT; + if (omap_readw(UDC_STAT_FLG) & UDC_NON_ISO_FIFO_EMPTY) { + omap_writew(UDC_SET_HALT, UDC_CTRL); status = 0; } else status = -EAGAIN; @@ -1170,10 +1161,10 @@ static int omap_ep_set_halt(struct usb_ep *_ep, int value) dma_channel_claim(ep, channel); } else { use_ep(ep, 0); - UDC_CTRL_REG = ep->udc->clr_halt; + omap_writew(ep->udc->clr_halt, UDC_CTRL); ep->ackwait = 0; if (!(ep->bEndpointAddress & USB_DIR_IN)) { - UDC_CTRL_REG = UDC_SET_FIFO_EN; + omap_writew(UDC_SET_FIFO_EN, UDC_CTRL); ep->ackwait = 1 + ep->double_buf; } } @@ -1205,7 +1196,7 @@ static struct usb_ep_ops omap_ep_ops = { static int omap_get_frame(struct usb_gadget *gadget) { - u16 sof = UDC_SOF_REG; + u16 sof = omap_readw(UDC_SOF); return (sof & UDC_TS_OK) ? (sof & UDC_TS) : -EL2NSYNC; } @@ -1224,7 +1215,7 @@ static int omap_wakeup(struct usb_gadget *gadget) */ if (udc->devstat & (UDC_B_HNP_ENABLE|UDC_R_WK_OK)) { DBG("remote wakeup...\n"); - UDC_SYSCON2_REG = UDC_RMT_WKP; + omap_writew(UDC_RMT_WKP, UDC_SYSCON2); retval = 0; } @@ -1247,12 +1238,12 @@ omap_set_selfpowered(struct usb_gadget *gadget, int is_selfpowered) udc = container_of(gadget, struct omap_udc, gadget); spin_lock_irqsave(&udc->lock, flags); - syscon1 = UDC_SYSCON1_REG; + syscon1 = omap_readw(UDC_SYSCON1); if (is_selfpowered) syscon1 |= UDC_SELF_PWR; else syscon1 &= ~UDC_SELF_PWR; - UDC_SYSCON1_REG = syscon1; + omap_writew(syscon1, UDC_SYSCON1); spin_unlock_irqrestore(&udc->lock, flags); return 0; @@ -1265,18 +1256,36 @@ static int can_pullup(struct omap_udc *udc) static void pullup_enable(struct omap_udc *udc) { - UDC_SYSCON1_REG |= UDC_PULLUP_EN; - if (!gadget_is_otg(&udc->gadget) && !cpu_is_omap15xx()) - OTG_CTRL_REG |= OTG_BSESSVLD; - UDC_IRQ_EN_REG = UDC_DS_CHG_IE; + u16 w; + + w = omap_readw(UDC_SYSCON1); + w |= UDC_PULLUP_EN; + omap_writew(w, UDC_SYSCON1); + if (!gadget_is_otg(&udc->gadget) && !cpu_is_omap15xx()) { + u32 l; + + l = omap_readl(OTG_CTRL); + l |= OTG_BSESSVLD; + omap_writel(l, OTG_CTRL); + } + omap_writew(UDC_DS_CHG_IE, UDC_IRQ_EN); } static void pullup_disable(struct omap_udc *udc) { - if (!gadget_is_otg(&udc->gadget) && !cpu_is_omap15xx()) - OTG_CTRL_REG &= ~OTG_BSESSVLD; - UDC_IRQ_EN_REG = UDC_DS_CHG_IE; - UDC_SYSCON1_REG &= ~UDC_PULLUP_EN; + u16 w; + + if (!gadget_is_otg(&udc->gadget) && !cpu_is_omap15xx()) { + u32 l; + + l = omap_readl(OTG_CTRL); + l &= ~OTG_BSESSVLD; + omap_writel(l, OTG_CTRL); + } + omap_writew(UDC_DS_CHG_IE, UDC_IRQ_EN); + w = omap_readw(UDC_SYSCON1); + w &= ~UDC_PULLUP_EN; + omap_writew(w, UDC_SYSCON1); } static struct omap_udc *udc; @@ -1304,6 +1313,7 @@ static int omap_vbus_session(struct usb_gadget *gadget, int is_active) { struct omap_udc *udc; unsigned long flags; + u32 l; udc = container_of(gadget, struct omap_udc, gadget); spin_lock_irqsave(&udc->lock, flags); @@ -1311,10 +1321,12 @@ static int omap_vbus_session(struct usb_gadget *gadget, int is_active) udc->vbus_active = (is_active != 0); if (cpu_is_omap15xx()) { /* "software" detect, ignored if !VBUS_MODE_1510 */ + l = omap_readl(FUNC_MUX_CTRL_0); if (is_active) - FUNC_MUX_CTRL_0_REG |= VBUS_CTRL_1510; + l |= VBUS_CTRL_1510; else - FUNC_MUX_CTRL_0_REG &= ~VBUS_CTRL_1510; + l &= ~VBUS_CTRL_1510; + omap_writel(l, FUNC_MUX_CTRL_0); } if (udc->dc_clk != NULL && is_active) { if (!udc->clk_requested) { @@ -1384,9 +1396,9 @@ static void nuke(struct omap_ep *ep, int status) dma_channel_release(ep); use_ep(ep, 0); - UDC_CTRL_REG = UDC_CLR_EP; + omap_writew(UDC_CLR_EP, UDC_CTRL); if (ep->bEndpointAddress && ep->bmAttributes != USB_ENDPOINT_XFER_ISOC) - UDC_CTRL_REG = UDC_SET_HALT; + omap_writew(UDC_SET_HALT, UDC_CTRL); while (!list_empty(&ep->queue)) { req = list_entry(ep->queue.next, struct omap_req, queue); @@ -1414,8 +1426,8 @@ static void update_otg(struct omap_udc *udc) if (!gadget_is_otg(&udc->gadget)) return; - if (OTG_CTRL_REG & OTG_ID) - devstat = UDC_DEVSTAT_REG; + if (omap_readl(OTG_CTRL) & OTG_ID) + devstat = omap_readw(UDC_DEVSTAT); else devstat = 0; @@ -1426,9 +1438,14 @@ static void update_otg(struct omap_udc *udc) /* Enable HNP early, avoiding races on suspend irq path. * ASSUMES OTG state machine B_BUS_REQ input is true. */ - if (udc->gadget.b_hnp_enable) - OTG_CTRL_REG = (OTG_CTRL_REG | OTG_B_HNPEN | OTG_B_BUSREQ) - & ~OTG_PULLUP; + if (udc->gadget.b_hnp_enable) { + u32 l; + + l = omap_readl(OTG_CTRL); + l |= OTG_B_HNPEN | OTG_B_BUSREQ; + l &= ~OTG_PULLUP; + omap_writel(l, OTG_CTRL); + } } static void ep0_irq(struct omap_udc *udc, u16 irq_src) @@ -1446,7 +1463,7 @@ static void ep0_irq(struct omap_udc *udc, u16 irq_src) nuke(ep0, 0); if (ack) { - UDC_IRQ_SRC_REG = ack; + omap_writew(ack, UDC_IRQ_SRC); irq_src = UDC_SETUP; } } @@ -1466,9 +1483,9 @@ static void ep0_irq(struct omap_udc *udc, u16 irq_src) if (irq_src & UDC_EP0_TX) { int stat; - UDC_IRQ_SRC_REG = UDC_EP0_TX; - UDC_EP_NUM_REG = UDC_EP_SEL|UDC_EP_DIR; - stat = UDC_STAT_FLG_REG; + omap_writew(UDC_EP0_TX, UDC_IRQ_SRC); + omap_writew(UDC_EP_SEL|UDC_EP_DIR, UDC_EP_NUM); + stat = omap_readw(UDC_STAT_FLG); if (stat & UDC_ACK) { if (udc->ep0_in) { /* write next IN packet from response, @@ -1476,26 +1493,26 @@ static void ep0_irq(struct omap_udc *udc, u16 irq_src) */ if (req) stat = write_fifo(ep0, req); - UDC_EP_NUM_REG = UDC_EP_DIR; + omap_writew(UDC_EP_DIR, UDC_EP_NUM); if (!req && udc->ep0_pending) { - UDC_EP_NUM_REG = UDC_EP_SEL; - UDC_CTRL_REG = UDC_CLR_EP; - UDC_CTRL_REG = UDC_SET_FIFO_EN; - UDC_EP_NUM_REG = 0; + omap_writew(UDC_EP_SEL, UDC_EP_NUM); + omap_writew(UDC_CLR_EP, UDC_CTRL); + omap_writew(UDC_SET_FIFO_EN, UDC_CTRL); + omap_writew(0, UDC_EP_NUM); udc->ep0_pending = 0; } /* else: 6 wait states before it'll tx */ } else { /* ack status stage of OUT transfer */ - UDC_EP_NUM_REG = UDC_EP_DIR; + omap_writew(UDC_EP_DIR, UDC_EP_NUM); if (req) done(ep0, req, 0); } req = NULL; } else if (stat & UDC_STALL) { - UDC_CTRL_REG = UDC_CLR_HALT; - UDC_EP_NUM_REG = UDC_EP_DIR; + omap_writew(UDC_CLR_HALT, UDC_CTRL); + omap_writew(UDC_EP_DIR, UDC_EP_NUM); } else { - UDC_EP_NUM_REG = UDC_EP_DIR; + omap_writew(UDC_EP_DIR, UDC_EP_NUM); } } @@ -1503,9 +1520,9 @@ static void ep0_irq(struct omap_udc *udc, u16 irq_src) if (irq_src & UDC_EP0_RX) { int stat; - UDC_IRQ_SRC_REG = UDC_EP0_RX; - UDC_EP_NUM_REG = UDC_EP_SEL; - stat = UDC_STAT_FLG_REG; + omap_writew(UDC_EP0_RX, UDC_IRQ_SRC); + omap_writew(UDC_EP_SEL, UDC_EP_NUM); + stat = omap_readw(UDC_STAT_FLG); if (stat & UDC_ACK) { if (!udc->ep0_in) { stat = 0; @@ -1513,34 +1530,35 @@ static void ep0_irq(struct omap_udc *udc, u16 irq_src) * reactiviting the fifo; stall on errors. */ if (!req || (stat = read_fifo(ep0, req)) < 0) { - UDC_SYSCON2_REG = UDC_STALL_CMD; + omap_writew(UDC_STALL_CMD, UDC_SYSCON2); udc->ep0_pending = 0; stat = 0; } else if (stat == 0) - UDC_CTRL_REG = UDC_SET_FIFO_EN; - UDC_EP_NUM_REG = 0; + omap_writew(UDC_SET_FIFO_EN, UDC_CTRL); + omap_writew(0, UDC_EP_NUM); /* activate status stage */ if (stat == 1) { done(ep0, req, 0); /* that may have STALLed ep0... */ - UDC_EP_NUM_REG = UDC_EP_SEL|UDC_EP_DIR; - UDC_CTRL_REG = UDC_CLR_EP; - UDC_CTRL_REG = UDC_SET_FIFO_EN; - UDC_EP_NUM_REG = UDC_EP_DIR; + omap_writew(UDC_EP_SEL | UDC_EP_DIR, + UDC_EP_NUM); + omap_writew(UDC_CLR_EP, UDC_CTRL); + omap_writew(UDC_SET_FIFO_EN, UDC_CTRL); + omap_writew(UDC_EP_DIR, UDC_EP_NUM); udc->ep0_pending = 0; } } else { /* ack status stage of IN transfer */ - UDC_EP_NUM_REG = 0; + omap_writew(0, UDC_EP_NUM); if (req) done(ep0, req, 0); } } else if (stat & UDC_STALL) { - UDC_CTRL_REG = UDC_CLR_HALT; - UDC_EP_NUM_REG = 0; + omap_writew(UDC_CLR_HALT, UDC_CTRL); + omap_writew(0, UDC_EP_NUM); } else { - UDC_EP_NUM_REG = 0; + omap_writew(0, UDC_EP_NUM); } } @@ -1555,14 +1573,14 @@ static void ep0_irq(struct omap_udc *udc, u16 irq_src) /* read the (latest) SETUP message */ do { - UDC_EP_NUM_REG = UDC_SETUP_SEL; + omap_writew(UDC_SETUP_SEL, UDC_EP_NUM); /* two bytes at a time */ - u.word[0] = UDC_DATA_REG; - u.word[1] = UDC_DATA_REG; - u.word[2] = UDC_DATA_REG; - u.word[3] = UDC_DATA_REG; - UDC_EP_NUM_REG = 0; - } while (UDC_IRQ_SRC_REG & UDC_SETUP); + u.word[0] = omap_readw(UDC_DATA); + u.word[1] = omap_readw(UDC_DATA); + u.word[2] = omap_readw(UDC_DATA); + u.word[3] = omap_readw(UDC_DATA); + omap_writew(0, UDC_EP_NUM); + } while (omap_readw(UDC_IRQ_SRC) & UDC_SETUP); #define w_value le16_to_cpu(u.r.wValue) #define w_index le16_to_cpu(u.r.wIndex) @@ -1593,9 +1611,9 @@ static void ep0_irq(struct omap_udc *udc, u16 irq_src) * later if it fails the request. */ if (udc->ep0_reset_config) - UDC_SYSCON2_REG = UDC_CLR_CFG; + omap_writew(UDC_CLR_CFG, UDC_SYSCON2); else - UDC_SYSCON2_REG = UDC_DEV_CFG; + omap_writew(UDC_DEV_CFG, UDC_SYSCON2); update_otg(udc); goto delegate; case USB_REQ_CLEAR_FEATURE: @@ -1613,10 +1631,10 @@ static void ep0_irq(struct omap_udc *udc, u16 irq_src) || !ep->desc) goto do_stall; use_ep(ep, 0); - UDC_CTRL_REG = udc->clr_halt; + omap_writew(udc->clr_halt, UDC_CTRL); ep->ackwait = 0; if (!(ep->bEndpointAddress & USB_DIR_IN)) { - UDC_CTRL_REG = UDC_SET_FIFO_EN; + omap_writew(UDC_SET_FIFO_EN, UDC_CTRL); ep->ackwait = 1 + ep->double_buf; } /* NOTE: assumes the host behaves sanely, @@ -1649,15 +1667,15 @@ static void ep0_irq(struct omap_udc *udc, u16 irq_src) } use_ep(ep, 0); /* can't halt if fifo isn't empty... */ - UDC_CTRL_REG = UDC_CLR_EP; - UDC_CTRL_REG = UDC_SET_HALT; + omap_writew(UDC_CLR_EP, UDC_CTRL); + omap_writew(UDC_SET_HALT, UDC_CTRL); VDBG("%s halted by host\n", ep->name); ep0out_status_stage: status = 0; - UDC_EP_NUM_REG = UDC_EP_SEL|UDC_EP_DIR; - UDC_CTRL_REG = UDC_CLR_EP; - UDC_CTRL_REG = UDC_SET_FIFO_EN; - UDC_EP_NUM_REG = UDC_EP_DIR; + omap_writew(UDC_EP_SEL|UDC_EP_DIR, UDC_EP_NUM); + omap_writew(UDC_CLR_EP, UDC_CTRL); + omap_writew(UDC_SET_FIFO_EN, UDC_CTRL); + omap_writew(UDC_EP_DIR, UDC_EP_NUM); udc->ep0_pending = 0; break; case USB_REQ_GET_STATUS: @@ -1694,10 +1712,10 @@ intf_status: zero_status: /* return two zero bytes */ - UDC_EP_NUM_REG = UDC_EP_SEL|UDC_EP_DIR; - UDC_DATA_REG = 0; - UDC_CTRL_REG = UDC_SET_FIFO_EN; - UDC_EP_NUM_REG = UDC_EP_DIR; + omap_writew(UDC_EP_SEL|UDC_EP_DIR, UDC_EP_NUM); + omap_writew(0, UDC_DATA); + omap_writew(UDC_SET_FIFO_EN, UDC_CTRL); + omap_writew(UDC_EP_DIR, UDC_EP_NUM); status = 0; VDBG("GET_STATUS, interface %d\n", w_index); /* next, status stage */ @@ -1706,8 +1724,8 @@ zero_status: delegate: /* activate the ep0out fifo right away */ if (!udc->ep0_in && w_length) { - UDC_EP_NUM_REG = 0; - UDC_CTRL_REG = UDC_SET_FIFO_EN; + omap_writew(0, UDC_EP_NUM); + omap_writew(UDC_SET_FIFO_EN, UDC_CTRL); } /* gadget drivers see class/vendor specific requests, @@ -1748,9 +1766,9 @@ do_stall: if (udc->ep0_reset_config) WARN("error resetting config?\n"); else - UDC_SYSCON2_REG = UDC_CLR_CFG; + omap_writew(UDC_CLR_CFG, UDC_SYSCON2); } - UDC_SYSCON2_REG = UDC_STALL_CMD; + omap_writew(UDC_STALL_CMD, UDC_SYSCON2); udc->ep0_pending = 0; } } @@ -1764,7 +1782,7 @@ static void devstate_irq(struct omap_udc *udc, u16 irq_src) { u16 devstat, change; - devstat = UDC_DEVSTAT_REG; + devstat = omap_readw(UDC_DEVSTAT); change = devstat ^ udc->devstat; udc->devstat = devstat; @@ -1804,7 +1822,8 @@ static void devstate_irq(struct omap_udc *udc, u16 irq_src) INFO("USB reset done, gadget %s\n", udc->driver->driver.name); /* ep0 traffic is legal from now on */ - UDC_IRQ_EN_REG = UDC_DS_CHG_IE | UDC_EP0_IE; + omap_writew(UDC_DS_CHG_IE | UDC_EP0_IE, + UDC_IRQ_EN); } change &= ~UDC_USB_RESET; } @@ -1848,7 +1867,7 @@ static void devstate_irq(struct omap_udc *udc, u16 irq_src) VDBG("devstat %03x, ignore change %03x\n", devstat, change); - UDC_IRQ_SRC_REG = UDC_DS_CHG; + omap_writew(UDC_DS_CHG, UDC_IRQ_SRC); } static irqreturn_t omap_udc_irq(int irq, void *_udc) @@ -1859,7 +1878,7 @@ static irqreturn_t omap_udc_irq(int irq, void *_udc) unsigned long flags; spin_lock_irqsave(&udc->lock, flags); - irq_src = UDC_IRQ_SRC_REG; + irq_src = omap_readw(UDC_IRQ_SRC); /* Device state change (usb ch9 stuff) */ if (irq_src & UDC_DS_CHG) { @@ -1882,7 +1901,7 @@ static irqreturn_t omap_udc_irq(int irq, void *_udc) irq_src &= ~(UDC_TXN_DONE|UDC_RXN_CNT|UDC_RXN_EOT); } - irq_src &= ~(UDC_SOF|UDC_EPN_TX|UDC_EPN_RX); + irq_src &= ~(UDC_IRQ_SOF | UDC_EPN_TX|UDC_EPN_RX); if (irq_src) DBG("udc_irq, unhandled %03x\n", irq_src); spin_unlock_irqrestore(&udc->lock, flags); @@ -1903,7 +1922,7 @@ static void pio_out_timer(unsigned long _ep) spin_lock_irqsave(&ep->udc->lock, flags); if (!list_empty(&ep->queue) && ep->ackwait) { use_ep(ep, UDC_EP_SEL); - stat_flg = UDC_STAT_FLG_REG; + stat_flg = omap_readw(UDC_STAT_FLG); if ((stat_flg & UDC_ACK) && (!(stat_flg & UDC_FIFO_EN) || (ep->double_buf && HALF_FULL(stat_flg)))) { @@ -1913,8 +1932,8 @@ static void pio_out_timer(unsigned long _ep) req = container_of(ep->queue.next, struct omap_req, queue); (void) read_fifo(ep, req); - UDC_EP_NUM_REG = ep->bEndpointAddress; - UDC_CTRL_REG = UDC_SET_FIFO_EN; + omap_writew(ep->bEndpointAddress, UDC_EP_NUM); + omap_writew(UDC_SET_FIFO_EN, UDC_CTRL); ep->ackwait = 1 + ep->double_buf; } else deselect_ep(); @@ -1934,20 +1953,20 @@ static irqreturn_t omap_udc_pio_irq(int irq, void *_dev) unsigned long flags; spin_lock_irqsave(&udc->lock, flags); - epn_stat = UDC_EPN_STAT_REG; - irq_src = UDC_IRQ_SRC_REG; + epn_stat = omap_readw(UDC_EPN_STAT); + irq_src = omap_readw(UDC_IRQ_SRC); /* handle OUT first, to avoid some wasteful NAKs */ if (irq_src & UDC_EPN_RX) { epnum = (epn_stat >> 8) & 0x0f; - UDC_IRQ_SRC_REG = UDC_EPN_RX; + omap_writew(UDC_EPN_RX, UDC_IRQ_SRC); status = IRQ_HANDLED; ep = &udc->ep[epnum]; ep->irqs++; - UDC_EP_NUM_REG = epnum | UDC_EP_SEL; + omap_writew(epnum | UDC_EP_SEL, UDC_EP_NUM); ep->fnf = 0; - if ((UDC_STAT_FLG_REG & UDC_ACK)) { + if (omap_readw(UDC_STAT_FLG) & UDC_ACK) { ep->ackwait--; if (!list_empty(&ep->queue)) { int stat; @@ -1959,15 +1978,15 @@ static irqreturn_t omap_udc_pio_irq(int irq, void *_dev) } } /* min 6 clock delay before clearing EP_SEL ... */ - epn_stat = UDC_EPN_STAT_REG; - epn_stat = UDC_EPN_STAT_REG; - UDC_EP_NUM_REG = epnum; + epn_stat = omap_readw(UDC_EPN_STAT); + epn_stat = omap_readw(UDC_EPN_STAT); + omap_writew(epnum, UDC_EP_NUM); /* enabling fifo _after_ clearing ACK, contrary to docs, * reduces lossage; timer still needed though (sigh). */ if (ep->fnf) { - UDC_CTRL_REG = UDC_SET_FIFO_EN; + omap_writew(UDC_SET_FIFO_EN, UDC_CTRL); ep->ackwait = 1 + ep->double_buf; } mod_timer(&ep->timer, PIO_OUT_TIMEOUT); @@ -1976,13 +1995,13 @@ static irqreturn_t omap_udc_pio_irq(int irq, void *_dev) /* then IN transfers */ else if (irq_src & UDC_EPN_TX) { epnum = epn_stat & 0x0f; - UDC_IRQ_SRC_REG = UDC_EPN_TX; + omap_writew(UDC_EPN_TX, UDC_IRQ_SRC); status = IRQ_HANDLED; ep = &udc->ep[16 + epnum]; ep->irqs++; - UDC_EP_NUM_REG = epnum | UDC_EP_DIR | UDC_EP_SEL; - if ((UDC_STAT_FLG_REG & UDC_ACK)) { + omap_writew(epnum | UDC_EP_DIR | UDC_EP_SEL, UDC_EP_NUM); + if (omap_readw(UDC_STAT_FLG) & UDC_ACK) { ep->ackwait = 0; if (!list_empty(&ep->queue)) { req = container_of(ep->queue.next, @@ -1991,9 +2010,9 @@ static irqreturn_t omap_udc_pio_irq(int irq, void *_dev) } } /* min 6 clock delay before clearing EP_SEL ... */ - epn_stat = UDC_EPN_STAT_REG; - epn_stat = UDC_EPN_STAT_REG; - UDC_EP_NUM_REG = epnum | UDC_EP_DIR; + epn_stat = omap_readw(UDC_EPN_STAT); + epn_stat = omap_readw(UDC_EPN_STAT); + omap_writew(epnum | UDC_EP_DIR, UDC_EP_NUM); /* then 6 clocks before it'd tx */ } @@ -2021,7 +2040,7 @@ static irqreturn_t omap_udc_iso_irq(int irq, void *_dev) req = list_entry(ep->queue.next, struct omap_req, queue); use_ep(ep, UDC_EP_SEL); - stat = UDC_STAT_FLG_REG; + stat = omap_readw(UDC_STAT_FLG); /* NOTE: like the other controller drivers, this isn't * currently reporting lost or damaged frames. @@ -2053,9 +2072,14 @@ static irqreturn_t omap_udc_iso_irq(int irq, void *_dev) if (!list_empty(&ep->queue)) pending = 1; } - if (!pending) - UDC_IRQ_EN_REG &= ~UDC_SOF_IE; - UDC_IRQ_SRC_REG = UDC_SOF; + if (!pending) { + u16 w; + + w = omap_readw(UDC_IRQ_EN); + w &= ~UDC_SOF_IE; + omap_writew(w, UDC_IRQ_EN); + } + omap_writew(UDC_IRQ_SOF, UDC_IRQ_SRC); spin_unlock_irqrestore(&udc->lock, flags); return IRQ_HANDLED; @@ -2104,7 +2128,7 @@ int usb_gadget_register_driver (struct usb_gadget_driver *driver) if (ep->bmAttributes == USB_ENDPOINT_XFER_ISOC) continue; use_ep(ep, 0); - UDC_CTRL_REG = UDC_SET_HALT; + omap_writew(UDC_SET_HALT, UDC_CTRL); } udc->ep0_pending = 0; udc->ep[0].irqs = 0; @@ -2128,7 +2152,7 @@ int usb_gadget_register_driver (struct usb_gadget_driver *driver) } DBG("bound to driver %s\n", driver->driver.name); - UDC_IRQ_SRC_REG = UDC_IRQ_SRC_MASK; + omap_writew(UDC_IRQ_SRC_MASK, UDC_IRQ_SRC); /* connect to bus through transceiver */ if (udc->transceiver) { @@ -2225,7 +2249,7 @@ static void proc_ep_show(struct seq_file *s, struct omap_ep *ep) else buf[0] = 0; - stat_flg = UDC_STAT_FLG_REG; + stat_flg = omap_readw(UDC_STAT_FLG); seq_printf(s, "\n%s %s%s%sirqs %ld stat %04x " EIGHTBITS FOURBITS "%s\n", ep->name, buf, @@ -2292,11 +2316,11 @@ static int proc_otg_show(struct seq_file *s) trans = CONTROL_DEVCONF_REG; } else { ctrl_name = "tranceiver_ctrl"; - trans = USB_TRANSCEIVER_CTRL_REG; + trans = omap_readw(USB_TRANSCEIVER_CTRL); } seq_printf(s, "\nOTG rev %d.%d, %s %05x\n", tmp >> 4, tmp & 0xf, ctrl_name, trans); - tmp = OTG_SYSCON_1_REG; + tmp = omap_readw(OTG_SYSCON_1); seq_printf(s, "otg_syscon1 %08x usb2 %s, usb1 %s, usb0 %s," FOURBITS "\n", tmp, trx_mode(USB2_TRX_MODE(tmp), trans & CONF_USB2_UNI_R), @@ -2308,7 +2332,7 @@ static int proc_otg_show(struct seq_file *s) (tmp & HST_IDLE_EN) ? " !host" : "", (tmp & DEV_IDLE_EN) ? " !dev" : "", (tmp & OTG_RESET_DONE) ? " reset_done" : " reset_active"); - tmp = OTG_SYSCON_2_REG; + tmp = omap_readl(OTG_SYSCON_2); seq_printf(s, "otg_syscon2 %08x%s" EIGHTBITS " b_ase_brst=%d hmc=%d\n", tmp, (tmp & OTG_EN) ? " otg_en" : "", @@ -2323,7 +2347,7 @@ static int proc_otg_show(struct seq_file *s) (tmp & HMC_TLLATTACH) ? " tllattach" : "", B_ASE_BRST(tmp), OTG_HMC(tmp)); - tmp = OTG_CTRL_REG; + tmp = omap_readl(OTG_CTRL); seq_printf(s, "otg_ctrl %06x" EIGHTBITS EIGHTBITS "%s\n", tmp, (tmp & OTG_ASESSVLD) ? " asess" : "", (tmp & OTG_BSESSEND) ? " bsess_end" : "", @@ -2343,13 +2367,13 @@ static int proc_otg_show(struct seq_file *s) (tmp & OTG_PU_VBUS) ? " pu_vb" : "", (tmp & OTG_PU_ID) ? " pu_id" : "" ); - tmp = OTG_IRQ_EN_REG; + tmp = omap_readw(OTG_IRQ_EN); seq_printf(s, "otg_irq_en %04x" "\n", tmp); - tmp = OTG_IRQ_SRC_REG; + tmp = omap_readw(OTG_IRQ_SRC); seq_printf(s, "otg_irq_src %04x" "\n", tmp); - tmp = OTG_OUTCTRL_REG; + tmp = omap_readw(OTG_OUTCTRL); seq_printf(s, "otg_outctrl %04x" "\n", tmp); - tmp = OTG_TEST_REG; + tmp = omap_readw(OTG_TEST); seq_printf(s, "otg_test %04x" "\n", tmp); return 0; } @@ -2370,7 +2394,7 @@ static int proc_udc_show(struct seq_file *s, void *_) driver_desc, use_dma ? " (dma)" : ""); - tmp = UDC_REV_REG & 0xff; + tmp = omap_readw(UDC_REV) & 0xff; seq_printf(s, "UDC rev %d.%d, fifo mode %d, gadget %s\n" "hmc %d, transceiver %s\n", @@ -2384,16 +2408,16 @@ static int proc_udc_show(struct seq_file *s, void *_) ? "external" : "(none)")); if (cpu_class_is_omap1()) { seq_printf(s, "ULPD control %04x req %04x status %04x\n", - __REG16(ULPD_CLOCK_CTRL), - __REG16(ULPD_SOFT_REQ), - __REG16(ULPD_STATUS_REQ)); + omap_readw(ULPD_CLOCK_CTRL), + omap_readw(ULPD_SOFT_REQ), + omap_readw(ULPD_STATUS_REQ)); } /* OTG controller registers */ if (!cpu_is_omap15xx()) proc_otg_show(s); - tmp = UDC_SYSCON1_REG; + tmp = omap_readw(UDC_SYSCON1); seq_printf(s, "\nsyscon1 %04x" EIGHTBITS "\n", tmp, (tmp & UDC_CFG_LOCK) ? " cfg_lock" : "", (tmp & UDC_DATA_ENDIAN) ? " data_endian" : "", @@ -2412,7 +2436,7 @@ static int proc_udc_show(struct seq_file *s, void *_) return 0; } - tmp = UDC_DEVSTAT_REG; + tmp = omap_readw(UDC_DEVSTAT); seq_printf(s, "devstat %04x" EIGHTBITS "%s%s\n", tmp, (tmp & UDC_B_HNP_ENABLE) ? " b_hnp" : "", (tmp & UDC_A_HNP_SUPPORT) ? " a_hnp" : "", @@ -2424,20 +2448,20 @@ static int proc_udc_show(struct seq_file *s, void *_) (tmp & UDC_ADD) ? " ADD" : "", (tmp & UDC_DEF) ? " DEF" : "", (tmp & UDC_ATT) ? " ATT" : ""); - seq_printf(s, "sof %04x\n", UDC_SOF_REG); - tmp = UDC_IRQ_EN_REG; + seq_printf(s, "sof %04x\n", omap_readw(UDC_SOF)); + tmp = omap_readw(UDC_IRQ_EN); seq_printf(s, "irq_en %04x" FOURBITS "%s\n", tmp, (tmp & UDC_SOF_IE) ? " sof" : "", (tmp & UDC_EPN_RX_IE) ? " epn_rx" : "", (tmp & UDC_EPN_TX_IE) ? " epn_tx" : "", (tmp & UDC_DS_CHG_IE) ? " ds_chg" : "", (tmp & UDC_EP0_IE) ? " ep0" : ""); - tmp = UDC_IRQ_SRC_REG; + tmp = omap_readw(UDC_IRQ_SRC); seq_printf(s, "irq_src %04x" EIGHTBITS "%s%s\n", tmp, (tmp & UDC_TXN_DONE) ? " txn_done" : "", (tmp & UDC_RXN_CNT) ? " rxn_cnt" : "", (tmp & UDC_RXN_EOT) ? " rxn_eot" : "", - (tmp & UDC_SOF) ? " sof" : "", + (tmp & UDC_IRQ_SOF) ? " sof" : "", (tmp & UDC_EPN_RX) ? " epn_rx" : "", (tmp & UDC_EPN_TX) ? " epn_tx" : "", (tmp & UDC_DS_CHG) ? " ds_chg" : "", @@ -2447,7 +2471,7 @@ static int proc_udc_show(struct seq_file *s, void *_) if (use_dma) { unsigned i; - tmp = UDC_DMA_IRQ_EN_REG; + tmp = omap_readw(UDC_DMA_IRQ_EN); seq_printf(s, "dma_irq_en %04x%s" EIGHTBITS "\n", tmp, (tmp & UDC_TX_DONE_IE(3)) ? " tx2_done" : "", (tmp & UDC_RX_CNT_IE(3)) ? " rx2_cnt" : "", @@ -2461,29 +2485,29 @@ static int proc_udc_show(struct seq_file *s, void *_) (tmp & UDC_RX_CNT_IE(1)) ? " rx0_cnt" : "", (tmp & UDC_RX_EOT_IE(1)) ? " rx0_eot" : ""); - tmp = UDC_RXDMA_CFG_REG; + tmp = omap_readw(UDC_RXDMA_CFG); seq_printf(s, "rxdma_cfg %04x\n", tmp); if (tmp) { for (i = 0; i < 3; i++) { if ((tmp & (0x0f << (i * 4))) == 0) continue; seq_printf(s, "rxdma[%d] %04x\n", i, - UDC_RXDMA_REG(i + 1)); + omap_readw(UDC_RXDMA(i + 1))); } } - tmp = UDC_TXDMA_CFG_REG; + tmp = omap_readw(UDC_TXDMA_CFG); seq_printf(s, "txdma_cfg %04x\n", tmp); if (tmp) { for (i = 0; i < 3; i++) { if (!(tmp & (0x0f << (i * 4)))) continue; seq_printf(s, "txdma[%d] %04x\n", i, - UDC_TXDMA_REG(i + 1)); + omap_readw(UDC_TXDMA(i + 1))); } } } - tmp = UDC_DEVSTAT_REG; + tmp = omap_readw(UDC_DEVSTAT); if (tmp & UDC_ATT) { proc_ep_show(s, &udc->ep[0]); if (tmp & UDC_ADD) { @@ -2535,7 +2559,7 @@ static inline void remove_proc_file(void) {} * buffer space among the endpoints we'll be operating. * * NOTE: as of OMAP 1710 ES2.0, writing a new endpoint config when - * UDC_SYSCON_1_REG.CFG_LOCK is set can now work. We won't use that + * UDC_SYSCON_1.CFG_LOCK is set can now work. We won't use that * capability yet though. */ static unsigned __init @@ -2597,9 +2621,9 @@ omap_ep_setup(char *name, u8 addr, u8 type, name, addr, epn_rxtx, maxp, dbuf ? "x2" : "", buf); if (addr & USB_DIR_IN) - UDC_EP_TX_REG(addr & 0xf) = epn_rxtx; + omap_writew(epn_rxtx, UDC_EP_TX(addr & 0xf)); else - UDC_EP_RX_REG(addr) = epn_rxtx; + omap_writew(epn_rxtx, UDC_EP_RX(addr)); /* next endpoint's buffer starts after this one's */ buf += maxp; @@ -2638,15 +2662,15 @@ omap_udc_setup(struct platform_device *odev, struct otg_transceiver *xceiv) unsigned tmp, buf; /* abolish any previous hardware state */ - UDC_SYSCON1_REG = 0; - UDC_IRQ_EN_REG = 0; - UDC_IRQ_SRC_REG = UDC_IRQ_SRC_MASK; - UDC_DMA_IRQ_EN_REG = 0; - UDC_RXDMA_CFG_REG = 0; - UDC_TXDMA_CFG_REG = 0; + omap_writew(0, UDC_SYSCON1); + omap_writew(0, UDC_IRQ_EN); + omap_writew(UDC_IRQ_SRC_MASK, UDC_IRQ_SRC); + omap_writew(0, UDC_DMA_IRQ_EN); + omap_writew(0, UDC_RXDMA_CFG); + omap_writew(0, UDC_TXDMA_CFG); /* UDC_PULLUP_EN gates the chip clock */ - // OTG_SYSCON_1_REG |= DEV_IDLE_EN; + // OTG_SYSCON_1 |= DEV_IDLE_EN; udc = kzalloc(sizeof(*udc), GFP_KERNEL); if (!udc) @@ -2677,8 +2701,8 @@ omap_udc_setup(struct platform_device *odev, struct otg_transceiver *xceiv) /* initially disable all non-ep0 endpoints */ for (tmp = 1; tmp < 15; tmp++) { - UDC_EP_RX_REG(tmp) = 0; - UDC_EP_TX_REG(tmp) = 0; + omap_writew(0, UDC_EP_RX(tmp)); + omap_writew(0, UDC_EP_TX(tmp)); } #define OMAP_BULK_EP(name,addr) \ @@ -2763,7 +2787,7 @@ omap_udc_setup(struct platform_device *odev, struct otg_transceiver *xceiv) ERR("unsupported fifo_mode #%d\n", fifo_mode); return -ENODEV; } - UDC_SYSCON1_REG = UDC_CFG_LOCK|UDC_SELF_PWR; + omap_writew(UDC_CFG_LOCK|UDC_SELF_PWR, UDC_SYSCON1); INFO("fifo mode %d, %d bytes not used\n", fifo_mode, 2048 - buf); return 0; } @@ -2807,7 +2831,7 @@ static int __init omap_udc_probe(struct platform_device *pdev) } INFO("OMAP UDC rev %d.%d%s\n", - UDC_REV_REG >> 4, UDC_REV_REG & 0xf, + omap_readw(UDC_REV) >> 4, omap_readw(UDC_REV) & 0xf, config->otg ? ", Mini-AB" : ""); /* use the mode given to us by board init code */ @@ -2822,12 +2846,12 @@ static int __init omap_udc_probe(struct platform_device *pdev) * know when to turn PULLUP_EN on/off; and that * means we always "need" the 48MHz clock. */ - u32 tmp = FUNC_MUX_CTRL_0_REG; - - FUNC_MUX_CTRL_0_REG &= ~VBUS_CTRL_1510; + u32 tmp = omap_readl(FUNC_MUX_CTRL_0); + tmp &= ~VBUS_CTRL_1510; + omap_writel(tmp, FUNC_MUX_CTRL_0); tmp |= VBUS_MODE_1510; tmp &= ~VBUS_CTRL_1510; - FUNC_MUX_CTRL_0_REG = tmp; + omap_writel(tmp, FUNC_MUX_CTRL_0); } } else { /* The transceiver may package some GPIO logic or handle @@ -2907,7 +2931,7 @@ known: #endif /* starting with omap1710 es2.0, clear toggle is a separate bit */ - if (UDC_REV_REG >= 0x61) + if (omap_readw(UDC_REV) >= 0x61) udc->clr_halt = UDC_RESET_EP | UDC_CLRDATA_TOGGLE; else udc->clr_halt = UDC_RESET_EP; @@ -3005,7 +3029,7 @@ static int __exit omap_udc_remove(struct platform_device *pdev) put_device(udc->transceiver->dev); udc->transceiver = NULL; } - UDC_SYSCON1_REG = 0; + omap_writew(0, UDC_SYSCON1); remove_proc_file(); @@ -3036,7 +3060,7 @@ static int __exit omap_udc_remove(struct platform_device *pdev) * * REVISIT we should probably reject suspend requests when there's a host * session active, rather than disconnecting, at least on boards that can - * report VBUS irqs (UDC_DEVSTAT_REG.UDC_ATT). And in any case, we need to + * report VBUS irqs (UDC_DEVSTAT.UDC_ATT). And in any case, we need to * make host resumes and VBUS detection trigger OMAP wakeup events; that * may involve talking to an external transceiver (e.g. isp1301). */ @@ -3045,7 +3069,7 @@ static int omap_udc_suspend(struct platform_device *dev, pm_message_t message) { u32 devstat; - devstat = UDC_DEVSTAT_REG; + devstat = omap_readw(UDC_DEVSTAT); /* we're requesting 48 MHz clock if the pullup is enabled * (== we're attached to the host) and we're not suspended, diff --git a/drivers/usb/gadget/omap_udc.h b/drivers/usb/gadget/omap_udc.h index c6b9cbc7230..8522bbb1227 100644 --- a/drivers/usb/gadget/omap_udc.h +++ b/drivers/usb/gadget/omap_udc.h @@ -8,23 +8,22 @@ /* * USB device/endpoint management registers */ -#define UDC_REG(offset) __REG16(UDC_BASE + (offset)) -#define UDC_REV_REG UDC_REG(0x0) /* Revision */ -#define UDC_EP_NUM_REG UDC_REG(0x4) /* Which endpoint */ +#define UDC_REV (UDC_BASE + 0x0) /* Revision */ +#define UDC_EP_NUM (UDC_BASE + 0x4) /* Which endpoint */ # define UDC_SETUP_SEL (1 << 6) # define UDC_EP_SEL (1 << 5) # define UDC_EP_DIR (1 << 4) /* low 4 bits for endpoint number */ -#define UDC_DATA_REG UDC_REG(0x08) /* Endpoint FIFO */ -#define UDC_CTRL_REG UDC_REG(0x0C) /* Endpoint control */ +#define UDC_DATA (UDC_BASE + 0x08) /* Endpoint FIFO */ +#define UDC_CTRL (UDC_BASE + 0x0C) /* Endpoint control */ # define UDC_CLR_HALT (1 << 7) # define UDC_SET_HALT (1 << 6) # define UDC_CLRDATA_TOGGLE (1 << 3) # define UDC_SET_FIFO_EN (1 << 2) # define UDC_CLR_EP (1 << 1) # define UDC_RESET_EP (1 << 0) -#define UDC_STAT_FLG_REG UDC_REG(0x10) /* Endpoint status */ +#define UDC_STAT_FLG (UDC_BASE + 0x10) /* Endpoint status */ # define UDC_NO_RXPACKET (1 << 15) # define UDC_MISS_IN (1 << 14) # define UDC_DATA_FLUSH (1 << 13) @@ -38,8 +37,8 @@ # define UDC_FIFO_EN (1 << 2) # define UDC_NON_ISO_FIFO_EMPTY (1 << 1) # define UDC_NON_ISO_FIFO_FULL (1 << 0) -#define UDC_RXFSTAT_REG UDC_REG(0x14) /* OUT bytecount */ -#define UDC_SYSCON1_REG UDC_REG(0x18) /* System config 1 */ +#define UDC_RXFSTAT (UDC_BASE + 0x14) /* OUT bytecount */ +#define UDC_SYSCON1 (UDC_BASE + 0x18) /* System config 1 */ # define UDC_CFG_LOCK (1 << 8) # define UDC_DATA_ENDIAN (1 << 7) # define UDC_DMA_ENDIAN (1 << 6) @@ -48,12 +47,12 @@ # define UDC_SELF_PWR (1 << 2) # define UDC_SOFF_DIS (1 << 1) # define UDC_PULLUP_EN (1 << 0) -#define UDC_SYSCON2_REG UDC_REG(0x1C) /* System config 2 */ +#define UDC_SYSCON2 (UDC_BASE + 0x1C) /* System config 2 */ # define UDC_RMT_WKP (1 << 6) # define UDC_STALL_CMD (1 << 5) # define UDC_DEV_CFG (1 << 3) # define UDC_CLR_CFG (1 << 2) -#define UDC_DEVSTAT_REG UDC_REG(0x20) /* Device status */ +#define UDC_DEVSTAT (UDC_BASE + 0x20) /* Device status */ # define UDC_B_HNP_ENABLE (1 << 9) # define UDC_A_HNP_SUPPORT (1 << 8) # define UDC_A_ALT_HNP_SUPPORT (1 << 7) @@ -64,26 +63,26 @@ # define UDC_ADD (1 << 2) # define UDC_DEF (1 << 1) # define UDC_ATT (1 << 0) -#define UDC_SOF_REG UDC_REG(0x24) /* Start of frame */ +#define UDC_SOF (UDC_BASE + 0x24) /* Start of frame */ # define UDC_FT_LOCK (1 << 12) # define UDC_TS_OK (1 << 11) # define UDC_TS 0x03ff -#define UDC_IRQ_EN_REG UDC_REG(0x28) /* Interrupt enable */ +#define UDC_IRQ_EN (UDC_BASE + 0x28) /* Interrupt enable */ # define UDC_SOF_IE (1 << 7) # define UDC_EPN_RX_IE (1 << 5) # define UDC_EPN_TX_IE (1 << 4) # define UDC_DS_CHG_IE (1 << 3) # define UDC_EP0_IE (1 << 0) -#define UDC_DMA_IRQ_EN_REG UDC_REG(0x2C) /* DMA irq enable */ +#define UDC_DMA_IRQ_EN (UDC_BASE + 0x2C) /* DMA irq enable */ /* rx/tx dma channels numbered 1-3 not 0-2 */ # define UDC_TX_DONE_IE(n) (1 << (4 * (n) - 2)) # define UDC_RX_CNT_IE(n) (1 << (4 * (n) - 3)) # define UDC_RX_EOT_IE(n) (1 << (4 * (n) - 4)) -#define UDC_IRQ_SRC_REG UDC_REG(0x30) /* Interrupt source */ +#define UDC_IRQ_SRC (UDC_BASE + 0x30) /* Interrupt source */ # define UDC_TXN_DONE (1 << 10) # define UDC_RXN_CNT (1 << 9) # define UDC_RXN_EOT (1 << 8) -# define UDC_SOF (1 << 7) +# define UDC_IRQ_SOF (1 << 7) # define UDC_EPN_RX (1 << 5) # define UDC_EPN_TX (1 << 4) # define UDC_DS_CHG (1 << 3) @@ -91,41 +90,41 @@ # define UDC_EP0_RX (1 << 1) # define UDC_EP0_TX (1 << 0) # define UDC_IRQ_SRC_MASK 0x7bf -#define UDC_EPN_STAT_REG UDC_REG(0x34) /* EP irq status */ -#define UDC_DMAN_STAT_REG UDC_REG(0x38) /* DMA irq status */ +#define UDC_EPN_STAT (UDC_BASE + 0x34) /* EP irq status */ +#define UDC_DMAN_STAT (UDC_BASE + 0x38) /* DMA irq status */ # define UDC_DMA_RX_SB (1 << 12) # define UDC_DMA_RX_SRC(x) (((x)>>8) & 0xf) # define UDC_DMA_TX_SRC(x) (((x)>>0) & 0xf) /* DMA configuration registers: up to three channels in each direction. */ -#define UDC_RXDMA_CFG_REG UDC_REG(0x40) /* 3 eps for RX DMA */ +#define UDC_RXDMA_CFG (UDC_BASE + 0x40) /* 3 eps for RX DMA */ # define UDC_DMA_REQ (1 << 12) -#define UDC_TXDMA_CFG_REG UDC_REG(0x44) /* 3 eps for TX DMA */ -#define UDC_DATA_DMA_REG UDC_REG(0x48) /* rx/tx fifo addr */ +#define UDC_TXDMA_CFG (UDC_BASE + 0x44) /* 3 eps for TX DMA */ +#define UDC_DATA_DMA (UDC_BASE + 0x48) /* rx/tx fifo addr */ /* rx/tx dma control, numbering channels 1-3 not 0-2 */ -#define UDC_TXDMA_REG(chan) UDC_REG(0x50 - 4 + 4 * (chan)) +#define UDC_TXDMA(chan) (UDC_BASE + 0x50 - 4 + 4 * (chan)) # define UDC_TXN_EOT (1 << 15) /* bytes vs packets */ # define UDC_TXN_START (1 << 14) /* start transfer */ # define UDC_TXN_TSC 0x03ff /* units in xfer */ -#define UDC_RXDMA_REG(chan) UDC_REG(0x60 - 4 + 4 * (chan)) +#define UDC_RXDMA(chan) (UDC_BASE + 0x60 - 4 + 4 * (chan)) # define UDC_RXN_STOP (1 << 15) /* enable EOT irq */ # define UDC_RXN_TC 0x00ff /* packets in xfer */ /* * Endpoint configuration registers (used before CFG_LOCK is set) - * UDC_EP_TX_REG(0) is unused + * UDC_EP_TX(0) is unused */ -#define UDC_EP_RX_REG(endpoint) UDC_REG(0x80 + (endpoint)*4) +#define UDC_EP_RX(endpoint) (UDC_BASE + 0x80 + (endpoint)*4) # define UDC_EPN_RX_VALID (1 << 15) # define UDC_EPN_RX_DB (1 << 14) /* buffer size in bits 13, 12 */ # define UDC_EPN_RX_ISO (1 << 11) /* buffer pointer in low 11 bits */ -#define UDC_EP_TX_REG(endpoint) UDC_REG(0xc0 + (endpoint)*4) - /* same bitfields as in RX_REG */ +#define UDC_EP_TX(endpoint) (UDC_BASE + 0xc0 + (endpoint)*4) + /* same bitfields as in RX */ /*-------------------------------------------------------------------------*/ @@ -195,14 +194,14 @@ struct omap_udc { /*-------------------------------------------------------------------------*/ -#define MOD_CONF_CTRL_0_REG __REG32(MOD_CONF_CTRL_0) -#define VBUS_W2FC_1510 (1 << 17) /* 0 gpio0, 1 dvdd2 pin */ +/* MOD_CONF_CTRL_0 */ +#define VBUS_W2FC_1510 (1 << 17) /* 0 gpio0, 1 dvdd2 pin */ -#define FUNC_MUX_CTRL_0_REG __REG32(FUNC_MUX_CTRL_0) +/* FUNC_MUX_CTRL_0 */ #define VBUS_CTRL_1510 (1 << 19) /* 1 connected (software) */ #define VBUS_MODE_1510 (1 << 18) /* 0 hardware, 1 software */ -#define HMC_1510 ((MOD_CONF_CTRL_0_REG >> 1) & 0x3f) -#define HMC_1610 (OTG_SYSCON_2_REG & 0x3f) +#define HMC_1510 ((omap_readl(MOD_CONF_CTRL_0) >> 1) & 0x3f) +#define HMC_1610 (omap_readl(OTG_SYSCON_2) & 0x3f) #define HMC (cpu_is_omap15xx() ? HMC_1510 : HMC_1610) diff --git a/drivers/usb/host/ohci-omap.c b/drivers/usb/host/ohci-omap.c index 6859fb5f1d6..2b7c04079d5 100644 --- a/drivers/usb/host/ohci-omap.c +++ b/drivers/usb/host/ohci-omap.c @@ -169,13 +169,16 @@ static void start_hnp(struct ohci_hcd *ohci) { const unsigned port = ohci_to_hcd(ohci)->self.otg_port - 1; unsigned long flags; + u32 l; otg_start_hnp(ohci->transceiver); local_irq_save(flags); ohci->transceiver->state = OTG_STATE_A_SUSPEND; writel (RH_PS_PSS, &ohci->regs->roothub.portstatus [port]); - OTG_CTRL_REG &= ~OTG_A_BUSREQ; + l = omap_readl(OTG_CTRL); + l &= ~OTG_A_BUSREQ; + omap_writel(l, OTG_CTRL); local_irq_restore(flags); } diff --git a/include/asm-arm/arch-at91/at91_pmc.h b/include/asm-arm/arch-at91/at91_pmc.h index c2b13c28015..2001e81f226 100644 --- a/include/asm-arm/arch-at91/at91_pmc.h +++ b/include/asm-arm/arch-at91/at91_pmc.h @@ -39,10 +39,14 @@ #define AT91_PMC_PCSR (AT91_PMC + 0x18) /* Peripheral Clock Status Register */ #define AT91_CKGR_UCKR (AT91_PMC + 0x1C) /* UTMI Clock Register [SAM9RL, CAP9] */ +#define AT91_PMC_UPLLEN (1 << 16) /* UTMI PLL Enable */ +#define AT91_PMC_UPLLCOUNT (0xf << 20) /* UTMI PLL Start-up Time */ +#define AT91_PMC_BIASEN (1 << 24) /* UTMI BIAS Enable */ +#define AT91_PMC_BIASCOUNT (0xf << 28) /* UTMI PLL Start-up Time */ #define AT91_CKGR_MOR (AT91_PMC + 0x20) /* Main Oscillator Register [not on SAM9RL] */ #define AT91_PMC_MOSCEN (1 << 0) /* Main Oscillator Enable */ -#define AT91_PMC_OSCBYPASS (1 << 1) /* Oscillator Bypass [AT91SAM926x only] */ +#define AT91_PMC_OSCBYPASS (1 << 1) /* Oscillator Bypass [SAM9x, CAP9] */ #define AT91_PMC_OSCOUNT (0xff << 8) /* Main Oscillator Start-up Time */ #define AT91_CKGR_MCFR (AT91_PMC + 0x24) /* Main Clock Frequency Register */ @@ -97,6 +101,7 @@ #define AT91_PMC_LOCKA (1 << 1) /* PLLA Lock */ #define AT91_PMC_LOCKB (1 << 2) /* PLLB Lock */ #define AT91_PMC_MCKRDY (1 << 3) /* Master Clock */ +#define AT91_PMC_LOCKU (1 << 6) /* UPLL Lock [AT91CAP9 only] */ #define AT91_PMC_PCK0RDY (1 << 8) /* Programmable Clock 0 */ #define AT91_PMC_PCK1RDY (1 << 9) /* Programmable Clock 1 */ #define AT91_PMC_PCK2RDY (1 << 10) /* Programmable Clock 2 */ diff --git a/include/asm-arm/arch-at91/at91cap9.h b/include/asm-arm/arch-at91/at91cap9.h index bac83adb505..6f14d9053ac 100644 --- a/include/asm-arm/arch-at91/at91cap9.h +++ b/include/asm-arm/arch-at91/at91cap9.h @@ -118,7 +118,7 @@ #define AT91CAP9_ROM_SIZE (32 * SZ_1K) /* Internal ROM size (32Kb) */ #define AT91CAP9_LCDC_BASE 0x00500000 /* LCD Controller */ -#define AT91CAP9_UDPHS_BASE 0x00600000 /* USB High Speed Device Port */ +#define AT91CAP9_UDPHS_FIFO 0x00600000 /* USB High Speed Device Port */ #define AT91CAP9_UHP_BASE 0x00700000 /* USB Host controller */ #define CONFIG_DRAM_BASE AT91_CHIPSELECT_6 diff --git a/include/asm-arm/arch-at91/at91cap9_matrix.h b/include/asm-arm/arch-at91/at91cap9_matrix.h index a641686b6c3..ddbd4873c84 100644 --- a/include/asm-arm/arch-at91/at91cap9_matrix.h +++ b/include/asm-arm/arch-at91/at91cap9_matrix.h @@ -106,6 +106,11 @@ #define AT91_MPBS0_SFR (AT91_MATRIX + 0x114) /* MPBlock Slave 0 Special Function Register */ #define AT91_MPBS1_SFR (AT91_MATRIX + 0x11C) /* MPBlock Slave 1 Special Function Register */ +#define AT91_MATRIX_UDPHS (AT91_MATRIX + 0x118) /* USBHS Special Function Register [AT91CAP9 only] */ +#define AT91_MATRIX_SELECT_UDPHS (0 << 31) /* select High Speed UDP */ +#define AT91_MATRIX_SELECT_UDP (1 << 31) /* select standard UDP */ +#define AT91_MATRIX_UDPHS_BYPASS_LOCK (1 << 30) /* bypass lock bit */ + #define AT91_MATRIX_EBICSA (AT91_MATRIX + 0x120) /* EBI Chip Select Assignment Register */ #define AT91_MATRIX_EBI_CS1A (1 << 1) /* Chip Select 1 Assignment */ #define AT91_MATRIX_EBI_CS1A_SMC (0 << 1) diff --git a/include/asm-arm/arch-at91/at91sam9260.h b/include/asm-arm/arch-at91/at91sam9260.h index c8934fe34dc..889872a3f2a 100644 --- a/include/asm-arm/arch-at91/at91sam9260.h +++ b/include/asm-arm/arch-at91/at91sam9260.h @@ -6,6 +6,8 @@ * Common definitions. * Based on AT91SAM9260 datasheet revision A (Preliminary). * + * Includes also definitions for AT91SAM9XE and AT91SAM9G families + * * This program is free software; you can redistribute it and/or modify * it under the terms of the GNU General Public License as published by * the Free Software Foundation; either version 2 of the License, or @@ -123,5 +125,14 @@ #define AT91SAM9XE_FLASH_BASE 0x00200000 /* Internal FLASH base address */ #define AT91SAM9XE_SRAM_BASE 0x00300000 /* Internal SRAM base address */ +#define AT91SAM9G20_ROM_BASE 0x00100000 /* Internal ROM base address */ +#define AT91SAM9G20_ROM_SIZE SZ_32K /* Internal ROM size (32Kb) */ + +#define AT91SAM9G20_SRAM0_BASE 0x00200000 /* Internal SRAM 0 base address */ +#define AT91SAM9G20_SRAM0_SIZE SZ_16K /* Internal SRAM 0 size (16Kb) */ +#define AT91SAM9G20_SRAM1_BASE 0x00300000 /* Internal SRAM 1 base address */ +#define AT91SAM9G20_SRAM1_SIZE SZ_16K /* Internal SRAM 1 size (16Kb) */ + +#define AT91SAM9G20_UHP_BASE 0x00500000 /* USB Host controller */ #endif diff --git a/include/asm-arm/arch-at91/at91sam9rl.h b/include/asm-arm/arch-at91/at91sam9rl.h index 16d2832f6c0..622e56f81d4 100644 --- a/include/asm-arm/arch-at91/at91sam9rl.h +++ b/include/asm-arm/arch-at91/at91sam9rl.h @@ -110,6 +110,6 @@ #define AT91SAM9RL_ROM_SIZE (2 * SZ_16K) /* Internal ROM size (32Kb) */ #define AT91SAM9RL_LCDC_BASE 0x00500000 /* LCD Controller */ -#define AT91SAM9RL_UDPHS_BASE 0x00600000 /* USB Device HS controller */ +#define AT91SAM9RL_UDPHS_FIFO 0x00600000 /* USB Device HS controller */ #endif diff --git a/include/asm-arm/arch-at91/board.h b/include/asm-arm/arch-at91/board.h index dc189f01c5b..94de788da76 100644 --- a/include/asm-arm/arch-at91/board.h +++ b/include/asm-arm/arch-at91/board.h @@ -36,6 +36,7 @@ #include <linux/i2c.h> #include <linux/leds.h> #include <linux/spi/spi.h> +#include <linux/usb/atmel_usba_udc.h> /* USB Device */ struct at91_udc_data { @@ -45,6 +46,9 @@ struct at91_udc_data { }; extern void __init at91_add_device_udc(struct at91_udc_data *data); + /* USB High Speed Device */ +extern void __init at91_add_device_usba(struct usba_platform_data *data); + /* Compact Flash */ struct at91_cf_data { u8 irq_pin; /* I/O IRQ */ @@ -73,7 +77,7 @@ struct at91_eth_data { }; extern void __init at91_add_device_eth(struct at91_eth_data *data); -#if defined(CONFIG_ARCH_AT91SAM9260) || defined(CONFIG_ARCH_AT91SAM9263) || defined(CONFIG_ARCH_AT91CAP9) +#if defined(CONFIG_ARCH_AT91SAM9260) || defined(CONFIG_ARCH_AT91SAM9263) || defined(CONFIG_ARCH_AT91SAM9G20) || defined(CONFIG_ARCH_AT91CAP9) #define eth_platform_data at91_eth_data #endif diff --git a/include/asm-arm/arch-at91/cpu.h b/include/asm-arm/arch-at91/cpu.h index 7145166826a..52df794205c 100644 --- a/include/asm-arm/arch-at91/cpu.h +++ b/include/asm-arm/arch-at91/cpu.h @@ -21,6 +21,7 @@ #define ARCH_ID_AT91SAM9260 0x019803a0 #define ARCH_ID_AT91SAM9261 0x019703a0 #define ARCH_ID_AT91SAM9263 0x019607a0 +#define ARCH_ID_AT91SAM9G20 0x019905a0 #define ARCH_ID_AT91SAM9RL64 0x019b03a0 #define ARCH_ID_AT91CAP9 0x039A03A0 @@ -63,6 +64,12 @@ static inline unsigned long at91_arch_identify(void) #define cpu_is_at91sam9260() (0) #endif +#ifdef CONFIG_ARCH_AT91SAM9G20 +#define cpu_is_at91sam9g20() (at91_cpu_identify() == ARCH_ID_AT91SAM9G20) +#else +#define cpu_is_at91sam9g20() (0) +#endif + #ifdef CONFIG_ARCH_AT91SAM9261 #define cpu_is_at91sam9261() (at91_cpu_identify() == ARCH_ID_AT91SAM9261) #else diff --git a/include/asm-arm/arch-at91/hardware.h b/include/asm-arm/arch-at91/hardware.h index 2c826d8247a..016a3a3f663 100644 --- a/include/asm-arm/arch-at91/hardware.h +++ b/include/asm-arm/arch-at91/hardware.h @@ -18,7 +18,7 @@ #if defined(CONFIG_ARCH_AT91RM9200) #include <asm/arch/at91rm9200.h> -#elif defined(CONFIG_ARCH_AT91SAM9260) +#elif defined(CONFIG_ARCH_AT91SAM9260) || defined(CONFIG_ARCH_AT91SAM9G20) #include <asm/arch/at91sam9260.h> #elif defined(CONFIG_ARCH_AT91SAM9261) #include <asm/arch/at91sam9261.h> diff --git a/include/asm-arm/arch-at91/timex.h b/include/asm-arm/arch-at91/timex.h index f1933b0fa43..298d8313cda 100644 --- a/include/asm-arm/arch-at91/timex.h +++ b/include/asm-arm/arch-at91/timex.h @@ -27,14 +27,29 @@ #define CLOCK_TICK_RATE (AT91_SLOW_CLOCK) -#elif defined(CONFIG_ARCH_AT91SAM9260) || defined(CONFIG_ARCH_AT91SAM9261) +#elif defined(CONFIG_ARCH_AT91SAM9260) + +#if defined(CONFIG_MACH_USB_A9260) || defined(CONFIG_MACH_QIL_A9260) +#define AT91SAM9_MASTER_CLOCK 90000000 +#else +#define AT91SAM9_MASTER_CLOCK 99300000 +#endif + +#define CLOCK_TICK_RATE (AT91SAM9_MASTER_CLOCK/16) + +#elif defined(CONFIG_ARCH_AT91SAM9261) #define AT91SAM9_MASTER_CLOCK 99300000 #define CLOCK_TICK_RATE (AT91SAM9_MASTER_CLOCK/16) #elif defined(CONFIG_ARCH_AT91SAM9263) +#if defined(CONFIG_MACH_USB_A9263) +#define AT91SAM9_MASTER_CLOCK 90000000 +#else #define AT91SAM9_MASTER_CLOCK 99959500 +#endif + #define CLOCK_TICK_RATE (AT91SAM9_MASTER_CLOCK/16) #elif defined(CONFIG_ARCH_AT91SAM9RL) @@ -42,6 +57,11 @@ #define AT91SAM9_MASTER_CLOCK 100000000 #define CLOCK_TICK_RATE (AT91SAM9_MASTER_CLOCK/16) +#elif defined(CONFIG_ARCH_AT91SAM9G20) + +#define AT91SAM9_MASTER_CLOCK 132096000 +#define CLOCK_TICK_RATE (AT91SAM9_MASTER_CLOCK/16) + #elif defined(CONFIG_ARCH_AT91CAP9) #define AT91CAP9_MASTER_CLOCK 100000000 diff --git a/include/asm-arm/arch-ebsa285/hardware.h b/include/asm-arm/arch-ebsa285/hardware.h index daad8ee2d19..74610c2c63d 100644 --- a/include/asm-arm/arch-ebsa285/hardware.h +++ b/include/asm-arm/arch-ebsa285/hardware.h @@ -14,7 +14,6 @@ #include <asm/arch/memory.h> -#ifdef CONFIG_ARCH_FOOTBRIDGE /* Virtual Physical Size * 0xff800000 0x40000000 1MB X-Bus * 0xff000000 0x7c000000 1MB PCI I/O space @@ -50,31 +49,6 @@ #define PCIMEM_SIZE 0x01000000 #define PCIMEM_BASE 0xf0000000 -#elif defined(CONFIG_ARCH_CO285) -/* - * This is the COEBSA285 cut-down mapping - */ -#define PCIMEM_SIZE 0x80000000 -#define PCIMEM_BASE 0x80000000 - -#define WFLUSH_SIZE 0x01000000 -#define WFLUSH_BASE 0x7d000000 - -#define ARMCSR_SIZE 0x00100000 -#define ARMCSR_BASE 0x7cf00000 - -#define XBUS_SIZE 0x00020000 -#define XBUS_BASE 0x7cee0000 - -#define PCIO_SIZE 0x00010000 -#define PCIO_BASE 0x7ced0000 - -#else - -#error "Undefined footbridge architecture" - -#endif - #define XBUS_LEDS ((volatile unsigned char *)(XBUS_BASE + 0x12000)) #define XBUS_LED_AMBER (1 << 0) #define XBUS_LED_GREEN (1 << 1) diff --git a/include/asm-arm/arch-ebsa285/memory.h b/include/asm-arm/arch-ebsa285/memory.h index cbd7ae64bcc..9019a3bf5ab 100644 --- a/include/asm-arm/arch-ebsa285/memory.h +++ b/include/asm-arm/arch-ebsa285/memory.h @@ -42,8 +42,6 @@ extern unsigned long __bus_to_virt(unsigned long); #endif -#if defined(CONFIG_ARCH_FOOTBRIDGE) - /* Task size and page offset at 3GB */ #define TASK_SIZE UL(0xbf000000) #define PAGE_OFFSET UL(0xc0000000) @@ -53,23 +51,6 @@ extern unsigned long __bus_to_virt(unsigned long); */ #define FLUSH_BASE 0xf9000000 -#elif defined(CONFIG_ARCH_CO285) - -/* Task size and page offset at 1.5GB */ -#define TASK_SIZE UL(0x5f000000) -#define PAGE_OFFSET UL(0x60000000) - -/* - * Cache flushing area. - */ -#define FLUSH_BASE 0x7e000000 - -#else - -#error "Undefined footbridge architecture" - -#endif - /* * Physical DRAM offset. */ diff --git a/include/asm-arm/arch-ebsa285/vmalloc.h b/include/asm-arm/arch-ebsa285/vmalloc.h index 02598200997..e487d7e8c8a 100644 --- a/include/asm-arm/arch-ebsa285/vmalloc.h +++ b/include/asm-arm/arch-ebsa285/vmalloc.h @@ -7,8 +7,4 @@ */ -#ifdef CONFIG_ARCH_FOOTBRIDGE #define VMALLOC_END (PAGE_OFFSET + 0x30000000) -#else -#define VMALLOC_END (PAGE_OFFSET + 0x20000000) -#endif diff --git a/include/asm-arm/arch-imx/imx-dma.h b/include/asm-arm/arch-imx/imx-dma.h index 5b1066da4e1..44d89c35539 100644 --- a/include/asm-arm/arch-imx/imx-dma.h +++ b/include/asm-arm/arch-imx/imx-dma.h @@ -88,7 +88,7 @@ int imx_dma_request(imx_dmach_t dma_ch, const char *name); void imx_dma_free(imx_dmach_t dma_ch); -int imx_dma_request_by_prio(imx_dmach_t *pdma_ch, const char *name, imx_dma_prio prio); +imx_dmach_t imx_dma_request_by_prio(const char *name, imx_dma_prio prio); #endif /* _ASM_ARCH_IMX_DMA_H */ diff --git a/include/asm-arm/arch-iop13xx/dma.h b/include/asm-arm/arch-iop13xx/dma.h index 2e15da53ff7..d79846fbb39 100644 --- a/include/asm-arm/arch-iop13xx/dma.h +++ b/include/asm-arm/arch-iop13xx/dma.h @@ -1,3 +1,3 @@ #ifndef _IOP13XX_DMA_H -#define _IOP13XX_DMA_H_ +#define _IOP13XX_DMA_H #endif diff --git a/include/asm-arm/arch-iop32x/gpio.h b/include/asm-arm/arch-iop32x/gpio.h new file mode 100644 index 00000000000..708f4ec9db1 --- /dev/null +++ b/include/asm-arm/arch-iop32x/gpio.h @@ -0,0 +1,6 @@ +#ifndef __ASM_ARCH_IOP32X_GPIO_H +#define __ASM_ARCH_IOP32X_GPIO_H + +#include <asm/hardware/iop3xx-gpio.h> + +#endif diff --git a/include/asm-arm/arch-iop33x/gpio.h b/include/asm-arm/arch-iop33x/gpio.h new file mode 100644 index 00000000000..ddd55bba9bb --- /dev/null +++ b/include/asm-arm/arch-iop33x/gpio.h @@ -0,0 +1,6 @@ +#ifndef __ASM_ARCH_IOP33X_GPIO_H +#define __ASM_ARCH_IOP33X_GPIO_H + +#include <asm/hardware/iop3xx-gpio.h> + +#endif diff --git a/include/asm-arm/arch-ixp4xx/fsg.h b/include/asm-arm/arch-ixp4xx/fsg.h new file mode 100644 index 00000000000..c0100cc7981 --- /dev/null +++ b/include/asm-arm/arch-ixp4xx/fsg.h @@ -0,0 +1,50 @@ +/* + * include/asm-arm/arch-ixp4xx/fsg.h + * + * Freecom FSG-3 platform specific definitions + * + * Author: Rod Whitby <rod@whitby.id.au> + * Author: Tomasz Chmielewski <mangoo@wpkg.org> + * Maintainers: http://www.nslu2-linux.org + * + * Based on coyote.h by + * Copyright 2004 (c) MontaVista, Software, Inc. + * + * This file is licensed under the terms of the GNU General Public + * License version 2. This program is licensed "as is" without any + * warranty of any kind, whether express or implied. + */ + +#ifndef __ASM_ARCH_HARDWARE_H__ +#error "Do not include this directly, instead #include <asm/hardware.h>" +#endif + +#define FSG_SDA_PIN 12 +#define FSG_SCL_PIN 13 + +/* + * FSG PCI IRQs + */ +#define FSG_PCI_MAX_DEV 3 +#define FSG_PCI_IRQ_LINES 3 + + +/* PCI controller GPIO to IRQ pin mappings */ +#define FSG_PCI_INTA_PIN 6 +#define FSG_PCI_INTB_PIN 7 +#define FSG_PCI_INTC_PIN 5 + +/* Buttons */ + +#define FSG_SB_GPIO 4 /* sync button */ +#define FSG_RB_GPIO 9 /* reset button */ +#define FSG_UB_GPIO 10 /* usb button */ + +/* LEDs */ + +#define FSG_LED_WLAN_BIT 0 +#define FSG_LED_WAN_BIT 1 +#define FSG_LED_SATA_BIT 2 +#define FSG_LED_USB_BIT 4 +#define FSG_LED_RING_BIT 5 +#define FSG_LED_SYNC_BIT 7 diff --git a/include/asm-arm/arch-ixp4xx/hardware.h b/include/asm-arm/arch-ixp4xx/hardware.h index 73e8dc36f6a..fa723a62785 100644 --- a/include/asm-arm/arch-ixp4xx/hardware.h +++ b/include/asm-arm/arch-ixp4xx/hardware.h @@ -45,5 +45,6 @@ #include "nslu2.h" #include "nas100d.h" #include "dsmg600.h" +#include "fsg.h" #endif /* _ASM_ARCH_HARDWARE_H */ diff --git a/include/asm-arm/arch-ixp4xx/irqs.h b/include/asm-arm/arch-ixp4xx/irqs.h index 11801605047..674af4a8414 100644 --- a/include/asm-arm/arch-ixp4xx/irqs.h +++ b/include/asm-arm/arch-ixp4xx/irqs.h @@ -128,4 +128,11 @@ #define IRQ_DSMG600_PCI_INTE IRQ_IXP4XX_GPIO7 #define IRQ_DSMG600_PCI_INTF IRQ_IXP4XX_GPIO6 +/* + * Freecom FSG-3 Board IRQs + */ +#define IRQ_FSG_PCI_INTA IRQ_IXP4XX_GPIO6 +#define IRQ_FSG_PCI_INTB IRQ_IXP4XX_GPIO7 +#define IRQ_FSG_PCI_INTC IRQ_IXP4XX_GPIO5 + #endif diff --git a/include/asm-arm/arch-kirkwood/debug-macro.S b/include/asm-arm/arch-kirkwood/debug-macro.S new file mode 100644 index 00000000000..f55fb8ad9ee --- /dev/null +++ b/include/asm-arm/arch-kirkwood/debug-macro.S @@ -0,0 +1,20 @@ +/* + * include/asm-arm/arch-kirkwood/debug-macro.S + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. +*/ + +#include <asm/arch/kirkwood.h> + + .macro addruart,rx + mrc p15, 0, \rx, c1, c0 + tst \rx, #1 @ MMU enabled? + ldreq \rx, =KIRKWOOD_REGS_PHYS_BASE + ldrne \rx, =KIRKWOOD_REGS_VIRT_BASE + orr \rx, \rx, #0x00012000 + .endm + +#define UART_SHIFT 2 +#include <asm/hardware/debug-8250.S> diff --git a/include/asm-arm/arch-kirkwood/dma.h b/include/asm-arm/arch-kirkwood/dma.h new file mode 100644 index 00000000000..40a8c178f10 --- /dev/null +++ b/include/asm-arm/arch-kirkwood/dma.h @@ -0,0 +1 @@ +/* empty */ diff --git a/include/asm-arm/arch-kirkwood/entry-macro.S b/include/asm-arm/arch-kirkwood/entry-macro.S new file mode 100644 index 00000000000..fc6a43d9355 --- /dev/null +++ b/include/asm-arm/arch-kirkwood/entry-macro.S @@ -0,0 +1,40 @@ +/* + * include/asm-arm/arch-kirkwood/entry-macro.S + * + * Low-level IRQ helper macros for Marvell Kirkwood platforms + * + * This file is licensed under the terms of the GNU General Public + * License version 2. This program is licensed "as is" without any + * warranty of any kind, whether express or implied. + */ + +#include <asm/arch/kirkwood.h> + + .macro disable_fiq + .endm + + .macro arch_ret_to_user, tmp1, tmp2 + .endm + + .macro get_irqnr_preamble, base, tmp + ldr \base, =IRQ_VIRT_BASE + .endm + + .macro get_irqnr_and_base, irqnr, irqstat, base, tmp + @ check low interrupts + ldr \irqstat, [\base, #IRQ_CAUSE_LOW_OFF] + ldr \tmp, [\base, #IRQ_MASK_LOW_OFF] + mov \irqnr, #31 + ands \irqstat, \irqstat, \tmp + bne 1001f + + @ if no low interrupts set, check high interrupts + ldr \irqstat, [\base, #IRQ_CAUSE_HIGH_OFF] + ldr \tmp, [\base, #IRQ_MASK_HIGH_OFF] + mov \irqnr, #63 + ands \irqstat, \irqstat, \tmp + + @ find first active interrupt source +1001: clzne \irqstat, \irqstat + subne \irqnr, \irqnr, \irqstat + .endm diff --git a/include/asm-arm/arch-kirkwood/hardware.h b/include/asm-arm/arch-kirkwood/hardware.h new file mode 100644 index 00000000000..e695719771a --- /dev/null +++ b/include/asm-arm/arch-kirkwood/hardware.h @@ -0,0 +1,21 @@ +/* + * include/asm-arm/arch-kirkwood/hardware.h + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ + +#ifndef __ASM_ARCH_HARDWARE_H +#define __ASM_ARCH_HARDWARE_H + +#include "kirkwood.h" + +#define pcibios_assign_all_busses() 1 + +#define PCIBIOS_MIN_IO 0x00001000 +#define PCIBIOS_MIN_MEM 0x01000000 +#define PCIMEM_BASE KIRKWOOD_PCIE_MEM_PHYS_BASE /* mem base for VGA */ + + +#endif diff --git a/include/asm-arm/arch-kirkwood/io.h b/include/asm-arm/arch-kirkwood/io.h new file mode 100644 index 00000000000..0ef6e95f5d5 --- /dev/null +++ b/include/asm-arm/arch-kirkwood/io.h @@ -0,0 +1,26 @@ +/* + * include/asm-arm/arch-kirkwood/io.h + * + * This file is licensed under the terms of the GNU General Public + * License version 2. This program is licensed "as is" without any + * warranty of any kind, whether express or implied. + */ + +#ifndef __ASM_ARCH_IO_H +#define __ASM_ARCH_IO_H + +#include "kirkwood.h" + +#define IO_SPACE_LIMIT 0xffffffff + +static inline void __iomem *__io(unsigned long addr) +{ + return (void __iomem *)((addr - KIRKWOOD_PCIE_IO_PHYS_BASE) + + KIRKWOOD_PCIE_IO_VIRT_BASE); +} + +#define __io(a) __io(a) +#define __mem_pci(a) (a) + + +#endif diff --git a/include/asm-arm/arch-kirkwood/irqs.h b/include/asm-arm/arch-kirkwood/irqs.h new file mode 100644 index 00000000000..2e7b5da6335 --- /dev/null +++ b/include/asm-arm/arch-kirkwood/irqs.h @@ -0,0 +1,63 @@ +/* + * include/asm-arm/arch-kirkwood/irqs.h + * + * IRQ definitions for Marvell Kirkwood SoCs + * + * This file is licensed under the terms of the GNU General Public + * License version 2. This program is licensed "as is" without any + * warranty of any kind, whether express or implied. + */ + +#ifndef __ASM_ARCH_IRQS_H +#define __ASM_ARCH_IRQS_H + +#include "kirkwood.h" /* need GPIO_MAX */ + +/* + * Low Interrupt Controller + */ +#define IRQ_KIRKWOOD_HIGH_SUM 0 +#define IRQ_KIRKWOOD_BRIDGE 1 +#define IRQ_KIRKWOOD_HOST2CPU 2 +#define IRQ_KIRKWOOD_CPU2HOST 3 +#define IRQ_KIRKWOOD_XOR_00 5 +#define IRQ_KIRKWOOD_XOR_01 6 +#define IRQ_KIRKWOOD_XOR_10 7 +#define IRQ_KIRKWOOD_XOR_11 8 +#define IRQ_KIRKWOOD_PCIE 9 +#define IRQ_KIRKWOOD_GE00_SUM 11 +#define IRQ_KIRKWOOD_GE01_SUM 15 +#define IRQ_KIRKWOOD_USB 19 +#define IRQ_KIRKWOOD_SATA 21 +#define IRQ_KIRKWOOD_CRYPTO 22 +#define IRQ_KIRKWOOD_SPI 23 +#define IRQ_KIRKWOOD_I2S 24 +#define IRQ_KIRKWOOD_TS_0 26 +#define IRQ_KIRKWOOD_SDIO 28 +#define IRQ_KIRKWOOD_TWSI 29 +#define IRQ_KIRKWOOD_AVB 30 +#define IRQ_KIRKWOOD_TDMI 31 + +/* + * High Interrupt Controller + */ +#define IRQ_KIRKWOOD_UART_0 33 +#define IRQ_KIRKWOOD_UART_1 34 +#define IRQ_KIRKWOOD_GPIO_LOW_0_7 35 +#define IRQ_KIRKWOOD_GPIO_LOW_8_15 36 +#define IRQ_KIRKWOOD_GPIO_LOW_16_23 37 +#define IRQ_KIRKWOOD_GPIO_LOW_24_31 38 +#define IRQ_KIRKWOOD_GPIO_HIGH_0_7 39 +#define IRQ_KIRKWOOD_GPIO_HIGH_8_15 40 +#define IRQ_KIRKWOOD_GPIO_HIGH_16_23 41 + +/* + * KIRKWOOD General Purpose Pins + */ +#define IRQ_KIRKWOOD_GPIO_START 64 +#define NR_GPIO_IRQS GPIO_MAX + +#define NR_IRQS (IRQ_KIRKWOOD_GPIO_START + NR_GPIO_IRQS) + + +#endif diff --git a/include/asm-arm/arch-kirkwood/kirkwood.h b/include/asm-arm/arch-kirkwood/kirkwood.h new file mode 100644 index 00000000000..bb31b315c35 --- /dev/null +++ b/include/asm-arm/arch-kirkwood/kirkwood.h @@ -0,0 +1,100 @@ +/* + * include/asm-arm/arch-kirkwood/kirkwood.h + * + * Generic definitions for Marvell Kirkwood SoC flavors: + * 88F6180, 88F6192 and 88F6281. + * + * This file is licensed under the terms of the GNU General Public + * License version 2. This program is licensed "as is" without any + * warranty of any kind, whether express or implied. + */ + +#ifndef __ASM_ARCH_KIRKWOOD_H +#define __ASM_ARCH_KIRKWOOD_H + +/* + * Marvell Kirkwood address maps. + * + * phys + * e0000000 PCIe Memory space + * f1000000 on-chip peripheral registers + * f2000000 PCIe I/O space + * f3000000 NAND controller address window + * + * virt phys size + * fee00000 f1000000 1M on-chip peripheral registers + * fef00000 f2000000 1M PCIe I/O space + */ + +#define KIRKWOOD_NAND_MEM_PHYS_BASE 0xf3000000 +#define KIRKWOOD_NAND_MEM_SIZE SZ_64K /* 1K is sufficient, but 64K + * is the minimal window size + */ + +#define KIRKWOOD_PCIE_IO_PHYS_BASE 0xf2000000 +#define KIRKWOOD_PCIE_IO_VIRT_BASE 0xfef00000 +#define KIRKWOOD_PCIE_IO_BUS_BASE 0x00000000 +#define KIRKWOOD_PCIE_IO_SIZE SZ_1M + +#define KIRKWOOD_REGS_PHYS_BASE 0xf1000000 +#define KIRKWOOD_REGS_VIRT_BASE 0xfee00000 +#define KIRKWOOD_REGS_SIZE SZ_1M + +#define KIRKWOOD_PCIE_MEM_PHYS_BASE 0xe0000000 +#define KIRKWOOD_PCIE_MEM_SIZE SZ_128M + +/* + * MBUS bridge registers. + */ +#define BRIDGE_VIRT_BASE (KIRKWOOD_REGS_VIRT_BASE | 0x20000) +#define CPU_CONTROL (BRIDGE_VIRT_BASE | 0x0104) +#define CPU_RESET 0x00000002 +#define RSTOUTn_MASK (BRIDGE_VIRT_BASE | 0x0108) +#define SOFT_RESET_OUT_EN 0x00000004 +#define SYSTEM_SOFT_RESET (BRIDGE_VIRT_BASE | 0x010c) +#define SOFT_RESET 0x00000001 +#define BRIDGE_CAUSE (BRIDGE_VIRT_BASE | 0x0110) +#define BRIDGE_MASK (BRIDGE_VIRT_BASE | 0x0114) +#define BRIDGE_INT_TIMER0 0x0002 +#define BRIDGE_INT_TIMER1 0x0004 +#define BRIDGE_INT_TIMER1_CLR (~0x0004) +#define IRQ_VIRT_BASE (BRIDGE_VIRT_BASE | 0x0200) +#define IRQ_CAUSE_LOW_OFF 0x0000 +#define IRQ_MASK_LOW_OFF 0x0004 +#define IRQ_CAUSE_HIGH_OFF 0x0010 +#define IRQ_MASK_HIGH_OFF 0x0014 +#define TIMER_VIRT_BASE (BRIDGE_VIRT_BASE | 0x0300) +#define L2_CONFIG_REG (BRIDGE_VIRT_BASE | 0x0128) +#define L2_WRITETHROUGH 0x00000010 + +/* + * Register Map + */ +#define DDR_VIRT_BASE (KIRKWOOD_REGS_VIRT_BASE | 0x00000) +#define DDR_WINDOW_CPU_BASE (DDR_VIRT_BASE | 0x1500) + +#define DEV_BUS_PHYS_BASE (KIRKWOOD_REGS_PHYS_BASE | 0x10000) +#define DEV_BUS_VIRT_BASE (KIRKWOOD_REGS_VIRT_BASE | 0x10000) +#define SAMPLE_AT_RESET (DEV_BUS_VIRT_BASE | 0x0030) +#define DEVICE_ID (DEV_BUS_VIRT_BASE | 0x0034) +#define RTC_PHYS_BASE (DEV_BUS_PHYS_BASE | 0x0300) +#define SPI_PHYS_BASE (DEV_BUS_PHYS_BASE | 0x0600) +#define UART0_PHYS_BASE (DEV_BUS_PHYS_BASE | 0x2000) +#define UART0_VIRT_BASE (DEV_BUS_VIRT_BASE | 0x2000) +#define UART1_PHYS_BASE (DEV_BUS_PHYS_BASE | 0x2100) +#define UART1_VIRT_BASE (DEV_BUS_VIRT_BASE | 0x2100) + +#define PCIE_VIRT_BASE (KIRKWOOD_REGS_VIRT_BASE | 0x40000) + +#define USB_PHYS_BASE (KIRKWOOD_REGS_PHYS_BASE | 0x50000) + +#define GE00_PHYS_BASE (KIRKWOOD_REGS_PHYS_BASE | 0x70000) +#define GE01_PHYS_BASE (KIRKWOOD_REGS_PHYS_BASE | 0x74000) + +#define SATA_PHYS_BASE (KIRKWOOD_REGS_PHYS_BASE | 0x80000) + + +#define GPIO_MAX 50 + + +#endif diff --git a/include/asm-arm/arch-kirkwood/memory.h b/include/asm-arm/arch-kirkwood/memory.h new file mode 100644 index 00000000000..e5108f408ce --- /dev/null +++ b/include/asm-arm/arch-kirkwood/memory.h @@ -0,0 +1,14 @@ +/* + * include/asm-arm/arch-kirkwood/memory.h + */ + +#ifndef __ASM_ARCH_MEMORY_H +#define __ASM_ARCH_MEMORY_H + +#define PHYS_OFFSET UL(0x00000000) + +#define __virt_to_bus(x) __virt_to_phys(x) +#define __bus_to_virt(x) __phys_to_virt(x) + + +#endif diff --git a/include/asm-arm/arch-kirkwood/system.h b/include/asm-arm/arch-kirkwood/system.h new file mode 100644 index 00000000000..8dde7e37985 --- /dev/null +++ b/include/asm-arm/arch-kirkwood/system.h @@ -0,0 +1,37 @@ +/* + * include/asm-arm/arch-kirkwood/system.h + * + * This file is licensed under the terms of the GNU General Public + * License version 2. This program is licensed "as is" without any + * warranty of any kind, whether express or implied. + */ + +#ifndef __ASM_ARCH_SYSTEM_H +#define __ASM_ARCH_SYSTEM_H + +#include <asm/arch/hardware.h> +#include <asm/arch/kirkwood.h> + +static inline void arch_idle(void) +{ + cpu_do_idle(); +} + +static inline void arch_reset(char mode) +{ + /* + * Enable soft reset to assert RSTOUTn. + */ + writel(SOFT_RESET_OUT_EN, RSTOUTn_MASK); + + /* + * Assert soft reset. + */ + writel(SOFT_RESET, SYSTEM_SOFT_RESET); + + while (1) + ; +} + + +#endif diff --git a/include/asm-arm/arch-kirkwood/timex.h b/include/asm-arm/arch-kirkwood/timex.h new file mode 100644 index 00000000000..82122e134e3 --- /dev/null +++ b/include/asm-arm/arch-kirkwood/timex.h @@ -0,0 +1,11 @@ +/* + * include/asm-arm/arch-kirkwood/timex.h + * + * This file is licensed under the terms of the GNU General Public + * License version 2. This program is licensed "as is" without any + * warranty of any kind, whether express or implied. + */ + +#define CLOCK_TICK_RATE (100 * HZ) + +#define KIRKWOOD_TCLK 166666667 diff --git a/include/asm-arm/arch-kirkwood/uncompress.h b/include/asm-arm/arch-kirkwood/uncompress.h new file mode 100644 index 00000000000..a9062b6d768 --- /dev/null +++ b/include/asm-arm/arch-kirkwood/uncompress.h @@ -0,0 +1,47 @@ +/* + * include/asm-arm/arch-kirkwood/uncompress.h + * + * This file is licensed under the terms of the GNU General Public + * License version 2. This program is licensed "as is" without any + * warranty of any kind, whether express or implied. + */ + +#include <linux/serial_reg.h> +#include <asm/arch/kirkwood.h> + +#define SERIAL_BASE ((unsigned char *)UART0_PHYS_BASE) + +static void putc(const char c) +{ + unsigned char *base = SERIAL_BASE; + int i; + + for (i = 0; i < 0x1000; i++) { + if (base[UART_LSR << 2] & UART_LSR_THRE) + break; + barrier(); + } + + base[UART_TX << 2] = c; +} + +static void flush(void) +{ + unsigned char *base = SERIAL_BASE; + unsigned char mask; + int i; + + mask = UART_LSR_TEMT | UART_LSR_THRE; + + for (i = 0; i < 0x1000; i++) { + if ((base[UART_LSR << 2] & mask) == mask) + break; + barrier(); + } +} + +/* + * nothing to do + */ +#define arch_decomp_setup() +#define arch_decomp_wdog() diff --git a/include/asm-arm/arch-kirkwood/vmalloc.h b/include/asm-arm/arch-kirkwood/vmalloc.h new file mode 100644 index 00000000000..41852c6e77f --- /dev/null +++ b/include/asm-arm/arch-kirkwood/vmalloc.h @@ -0,0 +1,5 @@ +/* + * include/asm-arm/arch-kirkwood/vmalloc.h + */ + +#define VMALLOC_END 0xfe800000 diff --git a/include/asm-arm/arch-loki/debug-macro.S b/include/asm-arm/arch-loki/debug-macro.S new file mode 100644 index 00000000000..585502e9651 --- /dev/null +++ b/include/asm-arm/arch-loki/debug-macro.S @@ -0,0 +1,20 @@ +/* + * include/asm-arm/arch-loki/debug-macro.S + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. +*/ + +#include <asm/arch/loki.h> + + .macro addruart,rx + mrc p15, 0, \rx, c1, c0 + tst \rx, #1 @ MMU enabled? + ldreq \rx, =LOKI_REGS_PHYS_BASE + ldrne \rx, =LOKI_REGS_VIRT_BASE + orr \rx, \rx, #0x00012000 + .endm + +#define UART_SHIFT 2 +#include <asm/hardware/debug-8250.S> diff --git a/include/asm-arm/arch-loki/dma.h b/include/asm-arm/arch-loki/dma.h new file mode 100644 index 00000000000..40a8c178f10 --- /dev/null +++ b/include/asm-arm/arch-loki/dma.h @@ -0,0 +1 @@ +/* empty */ diff --git a/include/asm-arm/arch-loki/entry-macro.S b/include/asm-arm/arch-loki/entry-macro.S new file mode 100644 index 00000000000..693257cdbeb --- /dev/null +++ b/include/asm-arm/arch-loki/entry-macro.S @@ -0,0 +1,30 @@ +/* + * include/asm-arm/arch-loki/entry-macro.S + * + * Low-level IRQ helper macros for Marvell Loki (88RC8480) platforms + * + * This file is licensed under the terms of the GNU General Public + * License version 2. This program is licensed "as is" without any + * warranty of any kind, whether express or implied. + */ + +#include <asm/arch/loki.h> + + .macro disable_fiq + .endm + + .macro arch_ret_to_user, tmp1, tmp2 + .endm + + .macro get_irqnr_preamble, base, tmp + ldr \base, =IRQ_VIRT_BASE + .endm + + .macro get_irqnr_and_base, irqnr, irqstat, base, tmp + ldr \irqstat, [\base, #IRQ_CAUSE_OFF] + ldr \tmp, [\base, #IRQ_MASK_OFF] + mov \irqnr, #0 + ands \irqstat, \irqstat, \tmp + clzne \irqnr, \irqstat + rsbne \irqnr, \irqnr, #31 + .endm diff --git a/include/asm-arm/arch-loki/hardware.h b/include/asm-arm/arch-loki/hardware.h new file mode 100644 index 00000000000..f65b01c733b --- /dev/null +++ b/include/asm-arm/arch-loki/hardware.h @@ -0,0 +1,15 @@ +/* + * include/asm-arm/arch-loki/hardware.h + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ + +#ifndef __ASM_ARCH_HARDWARE_H +#define __ASM_ARCH_HARDWARE_H + +#include "loki.h" + + +#endif diff --git a/include/asm-arm/arch-loki/io.h b/include/asm-arm/arch-loki/io.h new file mode 100644 index 00000000000..e7418a915e7 --- /dev/null +++ b/include/asm-arm/arch-loki/io.h @@ -0,0 +1,26 @@ +/* + * include/asm-arm/arch-loki/io.h + * + * This file is licensed under the terms of the GNU General Public + * License version 2. This program is licensed "as is" without any + * warranty of any kind, whether express or implied. + */ + +#ifndef __ASM_ARCH_IO_H +#define __ASM_ARCH_IO_H + +#include "loki.h" + +#define IO_SPACE_LIMIT 0xffffffff + +static inline void __iomem *__io(unsigned long addr) +{ + return (void __iomem *)((addr - LOKI_PCIE0_IO_PHYS_BASE) + + LOKI_PCIE0_IO_VIRT_BASE); +} + +#define __io(a) __io(a) +#define __mem_pci(a) (a) + + +#endif diff --git a/include/asm-arm/arch-loki/irqs.h b/include/asm-arm/arch-loki/irqs.h new file mode 100644 index 00000000000..7e497143807 --- /dev/null +++ b/include/asm-arm/arch-loki/irqs.h @@ -0,0 +1,58 @@ +/* + * include/asm-arm/arch-loki/irqs.h + * + * IRQ definitions for Marvell Loki (88RC8480) SoCs + * + * This file is licensed under the terms of the GNU General Public + * License version 2. This program is licensed "as is" without any + * warranty of any kind, whether express or implied. + */ + +#ifndef __ASM_ARCH_IRQS_H +#define __ASM_ARCH_IRQS_H + +#include "loki.h" /* need GPIO_MAX */ + +/* + * Interrupt Controller + */ +#define IRQ_LOKI_PCIE_A_CPU_DRBL 0 +#define IRQ_LOKI_CPU_PCIE_A_DRBL 1 +#define IRQ_LOKI_PCIE_B_CPU_DRBL 2 +#define IRQ_LOKI_CPU_PCIE_B_DRBL 3 +#define IRQ_LOKI_COM_A_ERR 6 +#define IRQ_LOKI_COM_A_IN 7 +#define IRQ_LOKI_COM_A_OUT 8 +#define IRQ_LOKI_COM_B_ERR 9 +#define IRQ_LOKI_COM_B_IN 10 +#define IRQ_LOKI_COM_B_OUT 11 +#define IRQ_LOKI_DMA_A 12 +#define IRQ_LOKI_DMA_B 13 +#define IRQ_LOKI_SAS_A 14 +#define IRQ_LOKI_SAS_B 15 +#define IRQ_LOKI_DDR 16 +#define IRQ_LOKI_XOR 17 +#define IRQ_LOKI_BRIDGE 18 +#define IRQ_LOKI_PCIE_A_ERR 20 +#define IRQ_LOKI_PCIE_A_INT 21 +#define IRQ_LOKI_PCIE_B_ERR 22 +#define IRQ_LOKI_PCIE_B_INT 23 +#define IRQ_LOKI_GBE_A_INT 24 +#define IRQ_LOKI_GBE_B_INT 25 +#define IRQ_LOKI_DEV_ERR 26 +#define IRQ_LOKI_UART0 27 +#define IRQ_LOKI_UART1 28 +#define IRQ_LOKI_TWSI 29 +#define IRQ_LOKI_GPIO_23_0 30 +#define IRQ_LOKI_GPIO_25_24 31 + +/* + * Loki General Purpose Pins + */ +#define IRQ_LOKI_GPIO_START 32 +#define NR_GPIO_IRQS GPIO_MAX + +#define NR_IRQS (IRQ_LOKI_GPIO_START + NR_GPIO_IRQS) + + +#endif diff --git a/include/asm-arm/arch-loki/loki.h b/include/asm-arm/arch-loki/loki.h new file mode 100644 index 00000000000..5dd05ee0a4e --- /dev/null +++ b/include/asm-arm/arch-loki/loki.h @@ -0,0 +1,97 @@ +/* + * include/asm-arm/arch-loki/loki.h + * + * Generic definitions for Marvell Loki (88RC8480) SoC flavors + * + * This file is licensed under the terms of the GNU General Public + * License version 2. This program is licensed "as is" without any + * warranty of any kind, whether express or implied. + */ + +#ifndef __ASM_ARCH_LOKI_H +#define __ASM_ARCH_LOKI_H + +/* + * Marvell Loki (88RC8480) address maps. + * + * phys + * d0000000 on-chip peripheral registers + * e0000000 PCIe 0 Memory space + * e8000000 PCIe 1 Memory space + * f0000000 PCIe 0 I/O space + * f0100000 PCIe 1 I/O space + * + * virt phys size + * fed00000 d0000000 1M on-chip peripheral registers + * fee00000 f0000000 64K PCIe 0 I/O space + * fef00000 f0100000 64K PCIe 1 I/O space + */ + +#define LOKI_REGS_PHYS_BASE 0xd0000000 +#define LOKI_REGS_VIRT_BASE 0xfed00000 +#define LOKI_REGS_SIZE SZ_1M + +#define LOKI_PCIE0_IO_PHYS_BASE 0xf0000000 +#define LOKI_PCIE0_IO_VIRT_BASE 0xfee00000 +#define LOKI_PCIE0_IO_BUS_BASE 0x00000000 +#define LOKI_PCIE0_IO_SIZE SZ_64K + +#define LOKI_PCIE1_IO_PHYS_BASE 0xf0100000 +#define LOKI_PCIE1_IO_VIRT_BASE 0xfef00000 +#define LOKI_PCIE1_IO_BUS_BASE 0x00000000 +#define LOKI_PCIE1_IO_SIZE SZ_64K + +#define LOKI_PCIE0_MEM_PHYS_BASE 0xe0000000 +#define LOKI_PCIE0_MEM_SIZE SZ_128M + +#define LOKI_PCIE1_MEM_PHYS_BASE 0xe8000000 +#define LOKI_PCIE1_MEM_SIZE SZ_128M + +/* + * Register Map + */ +#define DEV_BUS_PHYS_BASE (LOKI_REGS_PHYS_BASE | 0x10000) +#define DEV_BUS_VIRT_BASE (LOKI_REGS_VIRT_BASE | 0x10000) +#define UART0_PHYS_BASE (DEV_BUS_PHYS_BASE | 0x2000) +#define UART0_VIRT_BASE (DEV_BUS_VIRT_BASE | 0x2000) +#define UART1_PHYS_BASE (DEV_BUS_PHYS_BASE | 0x2100) +#define UART1_VIRT_BASE (DEV_BUS_VIRT_BASE | 0x2100) + +#define BRIDGE_VIRT_BASE (LOKI_REGS_VIRT_BASE | 0x20000) +#define BRIDGE_REG(x) (BRIDGE_VIRT_BASE | (x)) +#define RSTOUTn_MASK (BRIDGE_VIRT_BASE | 0x0108) +#define SOFT_RESET_OUT_EN 0x00000004 +#define SYSTEM_SOFT_RESET (BRIDGE_VIRT_BASE | 0x010c) +#define SOFT_RESET 0x00000001 +#define BRIDGE_CAUSE (BRIDGE_VIRT_BASE | 0x0110) +#define BRIDGE_MASK (BRIDGE_VIRT_BASE | 0x0114) +#define BRIDGE_INT_TIMER0 0x0002 +#define BRIDGE_INT_TIMER1 0x0004 +#define BRIDGE_INT_TIMER1_CLR 0x0004 +#define IRQ_VIRT_BASE (BRIDGE_VIRT_BASE | 0x0200) +#define IRQ_CAUSE_OFF 0x0000 +#define IRQ_MASK_OFF 0x0004 +#define TIMER_VIRT_BASE (BRIDGE_VIRT_BASE | 0x0300) + +#define PCIE0_VIRT_BASE (LOKI_REGS_VIRT_BASE | 0x30000) + +#define PCIE1_VIRT_BASE (LOKI_REGS_VIRT_BASE | 0x40000) + +#define SAS0_PHYS_BASE (LOKI_REGS_PHYS_BASE | 0x80000) + +#define SAS1_PHYS_BASE (LOKI_REGS_PHYS_BASE | 0x90000) + +#define GE0_PHYS_BASE (LOKI_REGS_PHYS_BASE | 0xa0000) +#define GE0_VIRT_BASE (LOKI_REGS_VIRT_BASE | 0xa0000) + +#define GE1_PHYS_BASE (LOKI_REGS_PHYS_BASE | 0xb0000) +#define GE1_VIRT_BASE (LOKI_REGS_VIRT_BASE | 0xb0000) + +#define DDR_VIRT_BASE (LOKI_REGS_VIRT_BASE | 0xf0000) +#define DDR_REG(x) (DDR_VIRT_BASE | (x)) + + +#define GPIO_MAX 8 + + +#endif diff --git a/include/asm-arm/arch-loki/memory.h b/include/asm-arm/arch-loki/memory.h new file mode 100644 index 00000000000..835101e4987 --- /dev/null +++ b/include/asm-arm/arch-loki/memory.h @@ -0,0 +1,14 @@ +/* + * include/asm-arm/arch-loki/memory.h + */ + +#ifndef __ASM_ARCH_MEMORY_H +#define __ASM_ARCH_MEMORY_H + +#define PHYS_OFFSET UL(0x00000000) + +#define __virt_to_bus(x) __virt_to_phys(x) +#define __bus_to_virt(x) __phys_to_virt(x) + + +#endif diff --git a/include/asm-arm/arch-loki/system.h b/include/asm-arm/arch-loki/system.h new file mode 100644 index 00000000000..a3568ac8ec3 --- /dev/null +++ b/include/asm-arm/arch-loki/system.h @@ -0,0 +1,37 @@ +/* + * include/asm-arm/arch-loki/system.h + * + * This file is licensed under the terms of the GNU General Public + * License version 2. This program is licensed "as is" without any + * warranty of any kind, whether express or implied. + */ + +#ifndef __ASM_ARCH_SYSTEM_H +#define __ASM_ARCH_SYSTEM_H + +#include <asm/arch/hardware.h> +#include <asm/arch/loki.h> + +static inline void arch_idle(void) +{ + cpu_do_idle(); +} + +static inline void arch_reset(char mode) +{ + /* + * Enable soft reset to assert RSTOUTn. + */ + writel(SOFT_RESET_OUT_EN, RSTOUTn_MASK); + + /* + * Assert soft reset. + */ + writel(SOFT_RESET, SYSTEM_SOFT_RESET); + + while (1) + ; +} + + +#endif diff --git a/include/asm-arm/arch-loki/timex.h b/include/asm-arm/arch-loki/timex.h new file mode 100644 index 00000000000..940014f97ca --- /dev/null +++ b/include/asm-arm/arch-loki/timex.h @@ -0,0 +1,11 @@ +/* + * include/asm-arm/arch-loki/timex.h + * + * This file is licensed under the terms of the GNU General Public + * License version 2. This program is licensed "as is" without any + * warranty of any kind, whether express or implied. + */ + +#define CLOCK_TICK_RATE (100 * HZ) + +#define LOKI_TCLK 180000000 diff --git a/include/asm-arm/arch-loki/uncompress.h b/include/asm-arm/arch-loki/uncompress.h new file mode 100644 index 00000000000..89a0cf88d3a --- /dev/null +++ b/include/asm-arm/arch-loki/uncompress.h @@ -0,0 +1,47 @@ +/* + * include/asm-arm/arch-loki/uncompress.h + * + * This file is licensed under the terms of the GNU General Public + * License version 2. This program is licensed "as is" without any + * warranty of any kind, whether express or implied. + */ + +#include <linux/serial_reg.h> +#include <asm/arch/loki.h> + +#define SERIAL_BASE ((unsigned char *)UART0_PHYS_BASE) + +static void putc(const char c) +{ + unsigned char *base = SERIAL_BASE; + int i; + + for (i = 0; i < 0x1000; i++) { + if (base[UART_LSR << 2] & UART_LSR_THRE) + break; + barrier(); + } + + base[UART_TX << 2] = c; +} + +static void flush(void) +{ + unsigned char *base = SERIAL_BASE; + unsigned char mask; + int i; + + mask = UART_LSR_TEMT | UART_LSR_THRE; + + for (i = 0; i < 0x1000; i++) { + if ((base[UART_LSR << 2] & mask) == mask) + break; + barrier(); + } +} + +/* + * nothing to do + */ +#define arch_decomp_setup() +#define arch_decomp_wdog() diff --git a/include/asm-arm/arch-loki/vmalloc.h b/include/asm-arm/arch-loki/vmalloc.h new file mode 100644 index 00000000000..f5be0622049 --- /dev/null +++ b/include/asm-arm/arch-loki/vmalloc.h @@ -0,0 +1,5 @@ +/* + * include/asm-arm/arch-loki/vmalloc.h + */ + +#define VMALLOC_END 0xfe800000 diff --git a/include/asm-arm/arch-msm/irqs.h b/include/asm-arm/arch-msm/irqs.h index 565430cfaa7..e62a108b185 100644 --- a/include/asm-arm/arch-msm/irqs.h +++ b/include/asm-arm/arch-msm/irqs.h @@ -15,6 +15,7 @@ */ #ifndef __ASM_ARCH_MSM_IRQS_H +#define __ASM_ARCH_MSM_IRQS_H /* MSM ARM11 Interrupt Numbers */ /* See 80-VE113-1 A, pp219-221 */ diff --git a/include/asm-arm/arch-msm/timex.h b/include/asm-arm/arch-msm/timex.h index 154b23fb359..8724487ab4c 100644 --- a/include/asm-arm/arch-msm/timex.h +++ b/include/asm-arm/arch-msm/timex.h @@ -14,6 +14,7 @@ */ #ifndef __ASM_ARCH_MSM_TIMEX_H +#define __ASM_ARCH_MSM_TIMEX_H #define CLOCK_TICK_RATE 1000000 diff --git a/include/asm-arm/arch-mv78xx0/debug-macro.S b/include/asm-arm/arch-mv78xx0/debug-macro.S new file mode 100644 index 00000000000..d0595bd645e --- /dev/null +++ b/include/asm-arm/arch-mv78xx0/debug-macro.S @@ -0,0 +1,20 @@ +/* + * include/asm-arm/arch-mv78xx0/debug-macro.S + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. +*/ + +#include <asm/arch/mv78xx0.h> + + .macro addruart,rx + mrc p15, 0, \rx, c1, c0 + tst \rx, #1 @ MMU enabled? + ldreq \rx, =MV78XX0_REGS_PHYS_BASE + ldrne \rx, =MV78XX0_REGS_VIRT_BASE + orr \rx, \rx, #0x00012000 + .endm + +#define UART_SHIFT 2 +#include <asm/hardware/debug-8250.S> diff --git a/include/asm-arm/arch-mv78xx0/dma.h b/include/asm-arm/arch-mv78xx0/dma.h new file mode 100644 index 00000000000..40a8c178f10 --- /dev/null +++ b/include/asm-arm/arch-mv78xx0/dma.h @@ -0,0 +1 @@ +/* empty */ diff --git a/include/asm-arm/arch-mv78xx0/entry-macro.S b/include/asm-arm/arch-mv78xx0/entry-macro.S new file mode 100644 index 00000000000..e9a606b1266 --- /dev/null +++ b/include/asm-arm/arch-mv78xx0/entry-macro.S @@ -0,0 +1,39 @@ +/* + * include/asm-arm/arch-mv78xx0/entry-macro.S + * + * Low-level IRQ helper macros for Marvell MV78xx0 platforms + * + * This file is licensed under the terms of the GNU General Public + * License version 2. This program is licensed "as is" without any + * warranty of any kind, whether express or implied. + */ + +#include <asm/arch/mv78xx0.h> + + .macro disable_fiq + .endm + + .macro arch_ret_to_user, tmp1, tmp2 + .endm + + .macro get_irqnr_preamble, base, tmp + ldr \base, =IRQ_VIRT_BASE + .endm + + .macro get_irqnr_and_base, irqnr, irqstat, base, tmp + @ check low interrupts + ldr \irqstat, [\base, #IRQ_CAUSE_LOW_OFF] + ldr \tmp, [\base, #IRQ_MASK_LOW_OFF] + mov \irqnr, #31 + ands \irqstat, \irqstat, \tmp + + @ if no low interrupts set, check high interrupts + ldreq \irqstat, [\base, #IRQ_CAUSE_HIGH_OFF] + ldreq \tmp, [\base, #IRQ_MASK_HIGH_OFF] + moveq \irqnr, #63 + andeqs \irqstat, \irqstat, \tmp + + @ find first active interrupt source + clzne \irqstat, \irqstat + subne \irqnr, \irqnr, \irqstat + .endm diff --git a/include/asm-arm/arch-mv78xx0/hardware.h b/include/asm-arm/arch-mv78xx0/hardware.h new file mode 100644 index 00000000000..8e17926086c --- /dev/null +++ b/include/asm-arm/arch-mv78xx0/hardware.h @@ -0,0 +1,21 @@ +/* + * include/asm-arm/arch-mv78xx0/hardware.h + * + * This file is licensed under the terms of the GNU General Public + * License version 2. This program is licensed "as is" without any + * warranty of any kind, whether express or implied. + */ + +#ifndef __ASM_ARCH_HARDWARE_H +#define __ASM_ARCH_HARDWARE_H + +#include "mv78xx0.h" + +#define pcibios_assign_all_busses() 1 + +#define PCIBIOS_MIN_IO 0x00001000 +#define PCIBIOS_MIN_MEM 0x01000000 +#define PCIMEM_BASE MV78XX0_PCIE_MEM_PHYS_BASE /* mem base for VGA */ + + +#endif diff --git a/include/asm-arm/arch-mv78xx0/io.h b/include/asm-arm/arch-mv78xx0/io.h new file mode 100644 index 00000000000..415d4c98e3d --- /dev/null +++ b/include/asm-arm/arch-mv78xx0/io.h @@ -0,0 +1,26 @@ +/* + * include/asm-arm/arch-mv78xx0/io.h + * + * This file is licensed under the terms of the GNU General Public + * License version 2. This program is licensed "as is" without any + * warranty of any kind, whether express or implied. + */ + +#ifndef __ASM_ARCH_IO_H +#define __ASM_ARCH_IO_H + +#include "mv78xx0.h" + +#define IO_SPACE_LIMIT 0xffffffff + +static inline void __iomem *__io(unsigned long addr) +{ + return (void __iomem *)((addr - MV78XX0_PCIE_IO_PHYS_BASE(0)) + + MV78XX0_PCIE_IO_VIRT_BASE(0)); +} + +#define __io(a) __io(a) +#define __mem_pci(a) (a) + + +#endif diff --git a/include/asm-arm/arch-mv78xx0/irqs.h b/include/asm-arm/arch-mv78xx0/irqs.h new file mode 100644 index 00000000000..75930450cd6 --- /dev/null +++ b/include/asm-arm/arch-mv78xx0/irqs.h @@ -0,0 +1,91 @@ +/* + * include/asm-arm/arch-mv78xx0/irqs.h + * + * IRQ definitions for Marvell MV78xx0 SoCs + * + * This file is licensed under the terms of the GNU General Public + * License version 2. This program is licensed "as is" without any + * warranty of any kind, whether express or implied. + */ + +#ifndef __ASM_ARCH_IRQS_H +#define __ASM_ARCH_IRQS_H + +#include "mv78xx0.h" /* need GPIO_MAX */ + +/* + * MV78xx0 Low Interrupt Controller + */ +#define IRQ_MV78XX0_ERR 0 +#define IRQ_MV78XX0_SPI 1 +#define IRQ_MV78XX0_I2C_0 2 +#define IRQ_MV78XX0_I2C_1 3 +#define IRQ_MV78XX0_IDMA_0 4 +#define IRQ_MV78XX0_IDMA_1 5 +#define IRQ_MV78XX0_IDMA_2 6 +#define IRQ_MV78XX0_IDMA_3 7 +#define IRQ_MV78XX0_TIMER_0 8 +#define IRQ_MV78XX0_TIMER_1 9 +#define IRQ_MV78XX0_TIMER_2 10 +#define IRQ_MV78XX0_TIMER_3 11 +#define IRQ_MV78XX0_UART_0 12 +#define IRQ_MV78XX0_UART_1 13 +#define IRQ_MV78XX0_UART_2 14 +#define IRQ_MV78XX0_UART_3 15 +#define IRQ_MV78XX0_USB_0 16 +#define IRQ_MV78XX0_USB_1 17 +#define IRQ_MV78XX0_USB_2 18 +#define IRQ_MV78XX0_CRYPTO 19 +#define IRQ_MV78XX0_SDIO_0 20 +#define IRQ_MV78XX0_SDIO_1 21 +#define IRQ_MV78XX0_XOR_0 22 +#define IRQ_MV78XX0_XOR_1 23 +#define IRQ_MV78XX0_I2S_0 24 +#define IRQ_MV78XX0_I2S_1 25 +#define IRQ_MV78XX0_SATA 26 +#define IRQ_MV78XX0_TDMI 27 + +/* + * MV78xx0 High Interrupt Controller + */ +#define IRQ_MV78XX0_PCIE_00 32 +#define IRQ_MV78XX0_PCIE_01 33 +#define IRQ_MV78XX0_PCIE_02 34 +#define IRQ_MV78XX0_PCIE_03 35 +#define IRQ_MV78XX0_PCIE_10 36 +#define IRQ_MV78XX0_PCIE_11 37 +#define IRQ_MV78XX0_PCIE_12 38 +#define IRQ_MV78XX0_PCIE_13 39 +#define IRQ_MV78XX0_GE00_SUM 40 +#define IRQ_MV78XX0_GE00_RX 41 +#define IRQ_MV78XX0_GE00_TX 42 +#define IRQ_MV78XX0_GE00_MISC 43 +#define IRQ_MV78XX0_GE01_SUM 44 +#define IRQ_MV78XX0_GE01_RX 45 +#define IRQ_MV78XX0_GE01_TX 46 +#define IRQ_MV78XX0_GE01_MISC 47 +#define IRQ_MV78XX0_GE10_SUM 48 +#define IRQ_MV78XX0_GE10_RX 49 +#define IRQ_MV78XX0_GE10_TX 50 +#define IRQ_MV78XX0_GE10_MISC 51 +#define IRQ_MV78XX0_GE11_SUM 52 +#define IRQ_MV78XX0_GE11_RX 53 +#define IRQ_MV78XX0_GE11_TX 54 +#define IRQ_MV78XX0_GE11_MISC 55 +#define IRQ_MV78XX0_GPIO_0_7 56 +#define IRQ_MV78XX0_GPIO_8_15 57 +#define IRQ_MV78XX0_GPIO_16_23 58 +#define IRQ_MV78XX0_GPIO_24_31 59 +#define IRQ_MV78XX0_DB_IN 60 +#define IRQ_MV78XX0_DB_OUT 61 + +/* + * MV78XX0 General Purpose Pins + */ +#define IRQ_MV78XX0_GPIO_START 64 +#define NR_GPIO_IRQS GPIO_MAX + +#define NR_IRQS (IRQ_MV78XX0_GPIO_START + NR_GPIO_IRQS) + + +#endif diff --git a/include/asm-arm/arch-mv78xx0/memory.h b/include/asm-arm/arch-mv78xx0/memory.h new file mode 100644 index 00000000000..721a6b185b9 --- /dev/null +++ b/include/asm-arm/arch-mv78xx0/memory.h @@ -0,0 +1,14 @@ +/* + * include/asm-arm/arch-mv78xx0/memory.h + */ + +#ifndef __ASM_ARCH_MEMORY_H +#define __ASM_ARCH_MEMORY_H + +#define PHYS_OFFSET UL(0x00000000) + +#define __virt_to_bus(x) __virt_to_phys(x) +#define __bus_to_virt(x) __phys_to_virt(x) + + +#endif diff --git a/include/asm-arm/arch-mv78xx0/mv78xx0.h b/include/asm-arm/arch-mv78xx0/mv78xx0.h new file mode 100644 index 00000000000..9f5d83c73fa --- /dev/null +++ b/include/asm-arm/arch-mv78xx0/mv78xx0.h @@ -0,0 +1,126 @@ +/* + * include/asm-arm/arch-mv78xx0/mv78xx0.h + * + * Generic definitions for Marvell MV78xx0 SoC flavors: + * MV781x0 and MV782x0. + * + * This file is licensed under the terms of the GNU General Public + * License version 2. This program is licensed "as is" without any + * warranty of any kind, whether express or implied. + */ + +#ifndef __ASM_ARCH_MV78XX0_H +#define __ASM_ARCH_MV78XX0_H + +/* + * Marvell MV78xx0 address maps. + * + * phys + * c0000000 PCIe Memory space + * f0800000 PCIe #0 I/O space + * f0900000 PCIe #1 I/O space + * f0a00000 PCIe #2 I/O space + * f0b00000 PCIe #3 I/O space + * f0c00000 PCIe #4 I/O space + * f0d00000 PCIe #5 I/O space + * f0e00000 PCIe #6 I/O space + * f0f00000 PCIe #7 I/O space + * f1000000 on-chip peripheral registers + * + * virt phys size + * fe400000 f102x000 16K core-specific peripheral registers + * fe700000 f0800000 1M PCIe #0 I/O space + * fe800000 f0900000 1M PCIe #1 I/O space + * fe900000 f0a00000 1M PCIe #2 I/O space + * fea00000 f0b00000 1M PCIe #3 I/O space + * feb00000 f0c00000 1M PCIe #4 I/O space + * fec00000 f0d00000 1M PCIe #5 I/O space + * fed00000 f0e00000 1M PCIe #6 I/O space + * fee00000 f0f00000 1M PCIe #7 I/O space + * fef00000 f1000000 1M on-chip peripheral registers + */ +#define MV78XX0_CORE0_REGS_PHYS_BASE 0xf1020000 +#define MV78XX0_CORE1_REGS_PHYS_BASE 0xf1024000 +#define MV78XX0_CORE_REGS_VIRT_BASE 0xfe400000 +#define MV78XX0_CORE_REGS_SIZE SZ_16K + +#define MV78XX0_PCIE_IO_PHYS_BASE(i) (0xf0800000 + ((i) << 20)) +#define MV78XX0_PCIE_IO_VIRT_BASE(i) (0xfe700000 + ((i) << 20)) +#define MV78XX0_PCIE_IO_SIZE SZ_1M + +#define MV78XX0_REGS_PHYS_BASE 0xf1000000 +#define MV78XX0_REGS_VIRT_BASE 0xfef00000 +#define MV78XX0_REGS_SIZE SZ_1M + +#define MV78XX0_PCIE_MEM_PHYS_BASE 0xc0000000 +#define MV78XX0_PCIE_MEM_SIZE 0x30000000 + +/* + * Core-specific peripheral registers. + */ +#define BRIDGE_VIRT_BASE (MV78XX0_CORE_REGS_VIRT_BASE) +#define CPU_CONTROL (BRIDGE_VIRT_BASE | 0x0104) +#define L2_WRITETHROUGH 0x00020000 +#define RSTOUTn_MASK (BRIDGE_VIRT_BASE | 0x0108) +#define SOFT_RESET_OUT_EN 0x00000004 +#define SYSTEM_SOFT_RESET (BRIDGE_VIRT_BASE | 0x010c) +#define SOFT_RESET 0x00000001 +#define BRIDGE_CAUSE (BRIDGE_VIRT_BASE | 0x0110) +#define BRIDGE_MASK (BRIDGE_VIRT_BASE | 0x0114) +#define BRIDGE_INT_TIMER0 0x0002 +#define BRIDGE_INT_TIMER1 0x0004 +#define BRIDGE_INT_TIMER1_CLR (~0x0004) +#define IRQ_VIRT_BASE (BRIDGE_VIRT_BASE | 0x0200) +#define IRQ_CAUSE_LOW_OFF 0x0004 +#define IRQ_CAUSE_HIGH_OFF 0x0008 +#define IRQ_MASK_LOW_OFF 0x0010 +#define IRQ_MASK_HIGH_OFF 0x0014 +#define TIMER_VIRT_BASE (BRIDGE_VIRT_BASE | 0x0300) + +/* + * Register Map + */ +#define DDR_VIRT_BASE (MV78XX0_REGS_VIRT_BASE | 0x00000) +#define DDR_WINDOW_CPU0_BASE (DDR_VIRT_BASE | 0x1500) +#define DDR_WINDOW_CPU1_BASE (DDR_VIRT_BASE | 0x1700) + +#define DEV_BUS_PHYS_BASE (MV78XX0_REGS_PHYS_BASE | 0x10000) +#define DEV_BUS_VIRT_BASE (MV78XX0_REGS_VIRT_BASE | 0x10000) +#define SAMPLE_AT_RESET_LOW (DEV_BUS_VIRT_BASE | 0x0030) +#define SAMPLE_AT_RESET_HIGH (DEV_BUS_VIRT_BASE | 0x0034) +#define UART0_PHYS_BASE (DEV_BUS_PHYS_BASE | 0x2000) +#define UART0_VIRT_BASE (DEV_BUS_VIRT_BASE | 0x2000) +#define UART1_PHYS_BASE (DEV_BUS_PHYS_BASE | 0x2100) +#define UART1_VIRT_BASE (DEV_BUS_VIRT_BASE | 0x2100) +#define UART2_PHYS_BASE (DEV_BUS_PHYS_BASE | 0x2200) +#define UART2_VIRT_BASE (DEV_BUS_VIRT_BASE | 0x2200) +#define UART3_PHYS_BASE (DEV_BUS_PHYS_BASE | 0x2300) +#define UART3_VIRT_BASE (DEV_BUS_VIRT_BASE | 0x2300) + +#define GE10_PHYS_BASE (MV78XX0_REGS_PHYS_BASE | 0x30000) +#define GE11_PHYS_BASE (MV78XX0_REGS_PHYS_BASE | 0x34000) + +#define PCIE00_VIRT_BASE (MV78XX0_REGS_VIRT_BASE | 0x40000) +#define PCIE01_VIRT_BASE (MV78XX0_REGS_VIRT_BASE | 0x44000) +#define PCIE02_VIRT_BASE (MV78XX0_REGS_VIRT_BASE | 0x48000) +#define PCIE03_VIRT_BASE (MV78XX0_REGS_VIRT_BASE | 0x4c000) + +#define USB0_PHYS_BASE (MV78XX0_REGS_PHYS_BASE | 0x50000) +#define USB1_PHYS_BASE (MV78XX0_REGS_PHYS_BASE | 0x51000) +#define USB2_PHYS_BASE (MV78XX0_REGS_PHYS_BASE | 0x52000) + +#define GE00_PHYS_BASE (MV78XX0_REGS_PHYS_BASE | 0x70000) +#define GE01_PHYS_BASE (MV78XX0_REGS_PHYS_BASE | 0x74000) + +#define PCIE10_VIRT_BASE (MV78XX0_REGS_VIRT_BASE | 0x80000) +#define PCIE11_VIRT_BASE (MV78XX0_REGS_VIRT_BASE | 0x84000) +#define PCIE12_VIRT_BASE (MV78XX0_REGS_VIRT_BASE | 0x88000) +#define PCIE13_VIRT_BASE (MV78XX0_REGS_VIRT_BASE | 0x8c000) + +#define SATA_PHYS_BASE (MV78XX0_REGS_PHYS_BASE | 0xa0000) + + +#define GPIO_MAX 32 + + +#endif diff --git a/include/asm-arm/arch-mv78xx0/system.h b/include/asm-arm/arch-mv78xx0/system.h new file mode 100644 index 00000000000..7eb47d376db --- /dev/null +++ b/include/asm-arm/arch-mv78xx0/system.h @@ -0,0 +1,37 @@ +/* + * include/asm-arm/arch-mv78xx0/system.h + * + * This file is licensed under the terms of the GNU General Public + * License version 2. This program is licensed "as is" without any + * warranty of any kind, whether express or implied. + */ + +#ifndef __ASM_ARCH_SYSTEM_H +#define __ASM_ARCH_SYSTEM_H + +#include <asm/arch/hardware.h> +#include <asm/arch/mv78xx0.h> + +static inline void arch_idle(void) +{ + cpu_do_idle(); +} + +static inline void arch_reset(char mode) +{ + /* + * Enable soft reset to assert RSTOUTn. + */ + writel(SOFT_RESET_OUT_EN, RSTOUTn_MASK); + + /* + * Assert soft reset. + */ + writel(SOFT_RESET, SYSTEM_SOFT_RESET); + + while (1) + ; +} + + +#endif diff --git a/include/asm-arm/arch-mv78xx0/timex.h b/include/asm-arm/arch-mv78xx0/timex.h new file mode 100644 index 00000000000..a854b1ccbd0 --- /dev/null +++ b/include/asm-arm/arch-mv78xx0/timex.h @@ -0,0 +1,9 @@ +/* + * include/asm-arm/arch-mv78xx0/timex.h + * + * This file is licensed under the terms of the GNU General Public + * License version 2. This program is licensed "as is" without any + * warranty of any kind, whether express or implied. + */ + +#define CLOCK_TICK_RATE (100 * HZ) diff --git a/include/asm-arm/arch-mv78xx0/uncompress.h b/include/asm-arm/arch-mv78xx0/uncompress.h new file mode 100644 index 00000000000..3bfe0a293ef --- /dev/null +++ b/include/asm-arm/arch-mv78xx0/uncompress.h @@ -0,0 +1,47 @@ +/* + * include/asm-arm/arch-mv78xx0/uncompress.h + * + * This file is licensed under the terms of the GNU General Public + * License version 2. This program is licensed "as is" without any + * warranty of any kind, whether express or implied. + */ + +#include <linux/serial_reg.h> +#include <asm/arch/mv78xx0.h> + +#define SERIAL_BASE ((unsigned char *)UART0_PHYS_BASE) + +static void putc(const char c) +{ + unsigned char *base = SERIAL_BASE; + int i; + + for (i = 0; i < 0x1000; i++) { + if (base[UART_LSR << 2] & UART_LSR_THRE) + break; + barrier(); + } + + base[UART_TX << 2] = c; +} + +static void flush(void) +{ + unsigned char *base = SERIAL_BASE; + unsigned char mask; + int i; + + mask = UART_LSR_TEMT | UART_LSR_THRE; + + for (i = 0; i < 0x1000; i++) { + if ((base[UART_LSR << 2] & mask) == mask) + break; + barrier(); + } +} + +/* + * nothing to do + */ +#define arch_decomp_setup() +#define arch_decomp_wdog() diff --git a/include/asm-arm/arch-mv78xx0/vmalloc.h b/include/asm-arm/arch-mv78xx0/vmalloc.h new file mode 100644 index 00000000000..f2c51219757 --- /dev/null +++ b/include/asm-arm/arch-mv78xx0/vmalloc.h @@ -0,0 +1,5 @@ +/* + * include/asm-arm/arch-mv78xx0/vmalloc.h + */ + +#define VMALLOC_END 0xfe000000 diff --git a/include/asm-arm/arch-ns9xxx/hardware.h b/include/asm-arm/arch-ns9xxx/hardware.h index 0b7b34603f1..0dca11ce21f 100644 --- a/include/asm-arm/arch-ns9xxx/hardware.h +++ b/include/asm-arm/arch-ns9xxx/hardware.h @@ -66,13 +66,13 @@ __REGGET(var, reg ## _ ## field) / __REGSHIFT(reg ## _ ## field) # define REGGETIM_IDX(var, reg, field, idx) \ - __REGGET(var, reg ## _ ## field((idx))) / \ + __REGGET(var, reg ## _ ## field((idx))) / \ __REGSHIFT(reg ## _ ## field((idx))) #else # define __REG(x) io_p2v(x) -# define __REG2(x, y) io_p2v((x) + (y)) +# define __REG2(x, y) io_p2v((x) + 4 * (y)) #endif diff --git a/include/asm-arm/arch-omap/board-2430sdp.h b/include/asm-arm/arch-omap/board-2430sdp.h index e9c65ce3cb1..c7db9004ec3 100644 --- a/include/asm-arm/arch-omap/board-2430sdp.h +++ b/include/asm-arm/arch-omap/board-2430sdp.h @@ -36,9 +36,4 @@ #define TWL4030_IRQNUM INT_24XX_SYS_NIRQ -/* TWL4030 Primary Interrupt Handler (PIH) interrupts */ -#define IH_TWL4030_BASE IH_BOARD_BASE -#define IH_TWL4030_END (IH_TWL4030_BASE+8) -#define NR_IRQS (IH_TWL4030_END) - #endif /* __ASM_ARCH_OMAP_2430SDP_H */ diff --git a/include/asm-arm/arch-omap/board-h3.h b/include/asm-arm/arch-omap/board-h3.h index 0f6404435ea..c5d0f32a40a 100644 --- a/include/asm-arm/arch-omap/board-h3.h +++ b/include/asm-arm/arch-omap/board-h3.h @@ -30,12 +30,6 @@ /* In OMAP1710 H3 the Ethernet is directly connected to CS1 */ #define OMAP1710_ETHR_START 0x04000300 -#define MAXIRQNUM (IH_BOARD_BASE) -#define MAXFIQNUM MAXIRQNUM -#define MAXSWINUM MAXIRQNUM - -#define NR_IRQS (MAXIRQNUM + 1) - extern void h3_mmc_init(void); extern void h3_mmc_slot_cover_handler(void *arg, int state); diff --git a/include/asm-arm/arch-omap/board-innovator.h b/include/asm-arm/arch-omap/board-innovator.h index 56d2c98e143..9ca03dec9d3 100644 --- a/include/asm-arm/arch-omap/board-innovator.h +++ b/include/asm-arm/arch-omap/board-innovator.h @@ -36,9 +36,6 @@ #define OMAP1510P1_EMIFS_PRI_VALUE 0x00 #define OMAP1510P1_EMIFF_PRI_VALUE 0x00 -#define NR_FPGA_IRQS 24 -#define NR_IRQS (IH_BOARD_BASE + NR_FPGA_IRQS) - #ifndef __ASSEMBLY__ void fpga_write(unsigned char val, int reg); unsigned char fpga_read(int reg); diff --git a/include/asm-arm/arch-omap/board-perseus2.h b/include/asm-arm/arch-omap/board-perseus2.h index eb74420cb43..d7429cb0f72 100644 --- a/include/asm-arm/arch-omap/board-perseus2.h +++ b/include/asm-arm/arch-omap/board-perseus2.h @@ -36,10 +36,4 @@ #define OMAP_SDRAM_DEVICE D256M_1X16_4B #endif -#define MAXIRQNUM IH_BOARD_BASE -#define MAXFIQNUM MAXIRQNUM -#define MAXSWINUM MAXIRQNUM - -#define NR_IRQS (MAXIRQNUM + 1) - #endif diff --git a/include/asm-arm/arch-omap/clock.h b/include/asm-arm/arch-omap/clock.h index 12a5e4de951..4c7b3514f71 100644 --- a/include/asm-arm/arch-omap/clock.h +++ b/include/asm-arm/arch-omap/clock.h @@ -33,12 +33,24 @@ struct dpll_data { void __iomem *mult_div1_reg; u32 mult_mask; u32 div1_mask; + u16 last_rounded_m; + u8 last_rounded_n; + unsigned long last_rounded_rate; + unsigned int rate_tolerance; + u16 max_multiplier; + u8 max_divider; + u32 max_tolerance; # if defined(CONFIG_ARCH_OMAP3) + u8 modes; void __iomem *control_reg; u32 enable_mask; u8 auto_recal_bit; u8 recal_en_bit; u8 recal_st_bit; + void __iomem *autoidle_reg; + u32 autoidle_mask; + void __iomem *idlest_reg; + u8 idlest_bit; # endif }; @@ -66,11 +78,14 @@ struct clk { void __iomem *clksel_reg; u32 clksel_mask; const struct clksel *clksel; - const struct dpll_data *dpll_data; + struct dpll_data *dpll_data; #else __u8 rate_offset; __u8 src_offset; #endif +#if defined(CONFIG_PM_DEBUG) && defined(CONFIG_DEBUG_FS) + struct dentry *dent; /* For visible tree hierarchy */ +#endif }; struct cpufreq_frequency_table; diff --git a/include/asm-arm/arch-omap/common.h b/include/asm-arm/arch-omap/common.h index 36a3b62d4d8..8ac03071f60 100644 --- a/include/asm-arm/arch-omap/common.h +++ b/include/asm-arm/arch-omap/common.h @@ -47,8 +47,23 @@ static inline int omap_register_i2c_bus(int bus_id, u32 clkrate, } #endif +/* IO bases for various OMAP processors */ +struct omap_globals { + void __iomem *tap; /* Control module ID code */ + void __iomem *sdrc; /* SDRAM Controller */ + void __iomem *sms; /* SDRAM Memory Scheduler */ + void __iomem *ctrl; /* System Control Module */ + void __iomem *prm; /* Power and Reset Management */ + void __iomem *cm; /* Clock Management */ +}; + void omap2_set_globals_242x(void); void omap2_set_globals_243x(void); void omap2_set_globals_343x(void); +/* These get called from omap2_set_globals_xxxx(), do not call these */ +void omap2_set_globals_memory(struct omap_globals *); +void omap2_set_globals_control(struct omap_globals *); +void omap2_set_globals_prcm(struct omap_globals *); + #endif /* __ARCH_ARM_MACH_OMAP_COMMON_H */ diff --git a/include/asm-arm/arch-omap/control.h b/include/asm-arm/arch-omap/control.h index 59c0686f8be..987553e3eeb 100644 --- a/include/asm-arm/arch-omap/control.h +++ b/include/asm-arm/arch-omap/control.h @@ -167,8 +167,7 @@ #ifndef __ASSEMBLY__ #if defined(CONFIG_ARCH_OMAP2) || defined(CONFIG_ARCH_OMAP3) -extern void omap_ctrl_base_set(u32 base); -extern u32 omap_ctrl_base_get(void); +extern void __iomem *omap_ctrl_base_get(void); extern u8 omap_ctrl_readb(u16 offset); extern u16 omap_ctrl_readw(u16 offset); extern u32 omap_ctrl_readl(u16 offset); @@ -176,7 +175,6 @@ extern void omap_ctrl_writeb(u8 val, u16 offset); extern void omap_ctrl_writew(u16 val, u16 offset); extern void omap_ctrl_writel(u32 val, u16 offset); #else -#define omap_ctrl_base_set(x) WARN_ON(1) #define omap_ctrl_base_get() 0 #define omap_ctrl_readb(x) 0 #define omap_ctrl_readw(x) 0 diff --git a/include/asm-arm/arch-omap/cpu.h b/include/asm-arm/arch-omap/cpu.h index e8a4cf52778..52db09f8328 100644 --- a/include/asm-arm/arch-omap/cpu.h +++ b/include/asm-arm/arch-omap/cpu.h @@ -3,7 +3,7 @@ * * OMAP cpu type detection * - * Copyright (C) 2004 Nokia Corporation + * Copyright (C) 2004, 2008 Nokia Corporation * * Written by Tony Lindgren <tony.lindgren@nokia.com> * @@ -26,6 +26,12 @@ #ifndef __ASM_ARCH_OMAP_CPU_H #define __ASM_ARCH_OMAP_CPU_H +struct omap_chip_id { + u8 oc; +}; + +#define OMAP_CHIP_INIT(x) { .oc = x } + extern unsigned int system_rev; #define omap2_cpu_rev() ((system_rev >> 12) & 0x0f) @@ -345,6 +351,33 @@ IS_OMAP_TYPE(3430, 0x3430) #define OMAP2430_REV_ES1_0 0x24300000 #define OMAP3430_REV_ES1_0 0x34300000 #define OMAP3430_REV_ES2_0 0x34301000 +#define OMAP3430_REV_ES2_1 0x34302000 +#define OMAP3430_REV_ES2_2 0x34303000 + +/* + * omap_chip bits + * + * CHIP_IS_OMAP{2420,2430,3430} indicate that a particular structure is + * valid on all chips of that type. CHIP_IS_OMAP3430ES{1,2} indicates + * something that is only valid on that particular ES revision. + * + * These bits may be ORed together to indicate structures that are + * available on multiple chip types. + * + * To test whether a particular structure matches the current OMAP chip type, + * use omap_chip_is(). + * + */ +#define CHIP_IS_OMAP2420 (1 << 0) +#define CHIP_IS_OMAP2430 (1 << 1) +#define CHIP_IS_OMAP3430 (1 << 2) +#define CHIP_IS_OMAP3430ES1 (1 << 3) +#define CHIP_IS_OMAP3430ES2 (1 << 4) + +#define CHIP_IS_OMAP24XX (CHIP_IS_OMAP2420 | CHIP_IS_OMAP2430) + +int omap_chip_is(struct omap_chip_id oci); + /* * Macro to detect device type i.e. EMU/HS/TST/GP/BAD @@ -362,6 +395,8 @@ IS_OMAP_TYPE(3430, 0x3430) #define is_device_type_gp() (get_device_type() == DEVICE_TYPE_GP) #define is_device_type_bad() (get_device_type() == DEVICE_TYPE_BAD) -#endif +void omap2_check_revision(void); + +#endif /* defined(CONFIG_ARCH_OMAP2) || defined(CONFIG_ARCH_OMAP3) */ #endif diff --git a/include/asm-arm/arch-omap/dma.h b/include/asm-arm/arch-omap/dma.h index 24acf090030..f4dcb958786 100644 --- a/include/asm-arm/arch-omap/dma.h +++ b/include/asm-arm/arch-omap/dma.h @@ -22,108 +22,128 @@ #define __ASM_ARCH_DMA_H /* Hardware registers for omap1 */ -#define OMAP_DMA_BASE (0xfffed800) -#define OMAP_DMA_GCR (OMAP_DMA_BASE + 0x400) -#define OMAP_DMA_GSCR (OMAP_DMA_BASE + 0x404) -#define OMAP_DMA_GRST (OMAP_DMA_BASE + 0x408) -#define OMAP_DMA_HW_ID (OMAP_DMA_BASE + 0x442) -#define OMAP_DMA_PCH2_ID (OMAP_DMA_BASE + 0x444) -#define OMAP_DMA_PCH0_ID (OMAP_DMA_BASE + 0x446) -#define OMAP_DMA_PCH1_ID (OMAP_DMA_BASE + 0x448) -#define OMAP_DMA_PCHG_ID (OMAP_DMA_BASE + 0x44a) -#define OMAP_DMA_PCHD_ID (OMAP_DMA_BASE + 0x44c) -#define OMAP_DMA_CAPS_0_U (OMAP_DMA_BASE + 0x44e) -#define OMAP_DMA_CAPS_0_L (OMAP_DMA_BASE + 0x450) -#define OMAP_DMA_CAPS_1_U (OMAP_DMA_BASE + 0x452) -#define OMAP_DMA_CAPS_1_L (OMAP_DMA_BASE + 0x454) -#define OMAP_DMA_CAPS_2 (OMAP_DMA_BASE + 0x456) -#define OMAP_DMA_CAPS_3 (OMAP_DMA_BASE + 0x458) -#define OMAP_DMA_CAPS_4 (OMAP_DMA_BASE + 0x45a) -#define OMAP_DMA_PCH2_SR (OMAP_DMA_BASE + 0x460) -#define OMAP_DMA_PCH0_SR (OMAP_DMA_BASE + 0x480) -#define OMAP_DMA_PCH1_SR (OMAP_DMA_BASE + 0x482) -#define OMAP_DMA_PCHD_SR (OMAP_DMA_BASE + 0x4c0) - -/* Hardware registers for omap2 */ -#if defined(CONFIG_ARCH_OMAP3) -#define OMAP_DMA4_BASE (L4_34XX_BASE + 0x56000) -#else /* CONFIG_ARCH_OMAP2 */ -#define OMAP_DMA4_BASE (L4_24XX_BASE + 0x56000) -#endif - -#define OMAP_DMA4_REVISION (OMAP_DMA4_BASE + 0x00) -#define OMAP_DMA4_GCR_REG (OMAP_DMA4_BASE + 0x78) -#define OMAP_DMA4_IRQSTATUS_L0 (OMAP_DMA4_BASE + 0x08) -#define OMAP_DMA4_IRQSTATUS_L1 (OMAP_DMA4_BASE + 0x0c) -#define OMAP_DMA4_IRQSTATUS_L2 (OMAP_DMA4_BASE + 0x10) -#define OMAP_DMA4_IRQSTATUS_L3 (OMAP_DMA4_BASE + 0x14) -#define OMAP_DMA4_IRQENABLE_L0 (OMAP_DMA4_BASE + 0x18) -#define OMAP_DMA4_IRQENABLE_L1 (OMAP_DMA4_BASE + 0x1c) -#define OMAP_DMA4_IRQENABLE_L2 (OMAP_DMA4_BASE + 0x20) -#define OMAP_DMA4_IRQENABLE_L3 (OMAP_DMA4_BASE + 0x24) -#define OMAP_DMA4_SYSSTATUS (OMAP_DMA4_BASE + 0x28) -#define OMAP_DMA4_OCP_SYSCONFIG (OMAP_DMA4_BASE + 0x2c) -#define OMAP_DMA4_CAPS_0 (OMAP_DMA4_BASE + 0x64) -#define OMAP_DMA4_CAPS_2 (OMAP_DMA4_BASE + 0x6c) -#define OMAP_DMA4_CAPS_3 (OMAP_DMA4_BASE + 0x70) -#define OMAP_DMA4_CAPS_4 (OMAP_DMA4_BASE + 0x74) - -#ifdef CONFIG_ARCH_OMAP1 - -#define OMAP_LOGICAL_DMA_CH_COUNT 17 +#define OMAP1_DMA_BASE (0xfffed800) + +#define OMAP1_DMA_GCR 0x400 +#define OMAP1_DMA_GSCR 0x404 +#define OMAP1_DMA_GRST 0x408 +#define OMAP1_DMA_HW_ID 0x442 +#define OMAP1_DMA_PCH2_ID 0x444 +#define OMAP1_DMA_PCH0_ID 0x446 +#define OMAP1_DMA_PCH1_ID 0x448 +#define OMAP1_DMA_PCHG_ID 0x44a +#define OMAP1_DMA_PCHD_ID 0x44c +#define OMAP1_DMA_CAPS_0_U 0x44e +#define OMAP1_DMA_CAPS_0_L 0x450 +#define OMAP1_DMA_CAPS_1_U 0x452 +#define OMAP1_DMA_CAPS_1_L 0x454 +#define OMAP1_DMA_CAPS_2 0x456 +#define OMAP1_DMA_CAPS_3 0x458 +#define OMAP1_DMA_CAPS_4 0x45a +#define OMAP1_DMA_PCH2_SR 0x460 +#define OMAP1_DMA_PCH0_SR 0x480 +#define OMAP1_DMA_PCH1_SR 0x482 +#define OMAP1_DMA_PCHD_SR 0x4c0 + +/* Hardware registers for omap2 and omap3 */ +#define OMAP24XX_DMA4_BASE (L4_24XX_BASE + 0x56000) +#define OMAP34XX_DMA4_BASE (L4_34XX_BASE + 0x56000) + +#define OMAP_DMA4_REVISION 0x00 +#define OMAP_DMA4_GCR 0x78 +#define OMAP_DMA4_IRQSTATUS_L0 0x08 +#define OMAP_DMA4_IRQSTATUS_L1 0x0c +#define OMAP_DMA4_IRQSTATUS_L2 0x10 +#define OMAP_DMA4_IRQSTATUS_L3 0x14 +#define OMAP_DMA4_IRQENABLE_L0 0x18 +#define OMAP_DMA4_IRQENABLE_L1 0x1c +#define OMAP_DMA4_IRQENABLE_L2 0x20 +#define OMAP_DMA4_IRQENABLE_L3 0x24 +#define OMAP_DMA4_SYSSTATUS 0x28 +#define OMAP_DMA4_OCP_SYSCONFIG 0x2c +#define OMAP_DMA4_CAPS_0 0x64 +#define OMAP_DMA4_CAPS_2 0x6c +#define OMAP_DMA4_CAPS_3 0x70 +#define OMAP_DMA4_CAPS_4 0x74 + +#define OMAP1_LOGICAL_DMA_CH_COUNT 17 +#define OMAP_DMA4_LOGICAL_DMA_CH_COUNT 32 /* REVISIT: Is this 32 + 2? */ /* Common channel specific registers for omap1 */ -#define OMAP_DMA_CSDP_REG(n) __REG16(OMAP_DMA_BASE + 0x40 * (n) + 0x00) -#define OMAP_DMA_CCR_REG(n) __REG16(OMAP_DMA_BASE + 0x40 * (n) + 0x02) -#define OMAP_DMA_CICR_REG(n) __REG16(OMAP_DMA_BASE + 0x40 * (n) + 0x04) -#define OMAP_DMA_CSR_REG(n) __REG16(OMAP_DMA_BASE + 0x40 * (n) + 0x06) -#define OMAP_DMA_CEN_REG(n) __REG16(OMAP_DMA_BASE + 0x40 * (n) + 0x10) -#define OMAP_DMA_CFN_REG(n) __REG16(OMAP_DMA_BASE + 0x40 * (n) + 0x12) -#define OMAP_DMA_CSFI_REG(n) __REG16(OMAP_DMA_BASE + 0x40 * (n) + 0x14) -#define OMAP_DMA_CSEI_REG(n) __REG16(OMAP_DMA_BASE + 0x40 * (n) + 0x16) -#define OMAP_DMA_CSAC_REG(n) __REG16(OMAP_DMA_BASE + 0x40 * (n) + 0x18) -#define OMAP_DMA_CDAC_REG(n) __REG16(OMAP_DMA_BASE + 0x40 * (n) + 0x1a) -#define OMAP_DMA_CDEI_REG(n) __REG16(OMAP_DMA_BASE + 0x40 * (n) + 0x1c) -#define OMAP_DMA_CDFI_REG(n) __REG16(OMAP_DMA_BASE + 0x40 * (n) + 0x1e) -#define OMAP_DMA_CLNK_CTRL_REG(n) __REG16(OMAP_DMA_BASE + 0x40 * (n) + 0x28) - -#else - -#define OMAP_LOGICAL_DMA_CH_COUNT 32 /* REVISIT: Is this 32 + 2? */ +#define OMAP1_DMA_CH_BASE(n) (0x40 * (n) + 0x00) +#define OMAP1_DMA_CSDP(n) (0x40 * (n) + 0x00) +#define OMAP1_DMA_CCR(n) (0x40 * (n) + 0x02) +#define OMAP1_DMA_CICR(n) (0x40 * (n) + 0x04) +#define OMAP1_DMA_CSR(n) (0x40 * (n) + 0x06) +#define OMAP1_DMA_CEN(n) (0x40 * (n) + 0x10) +#define OMAP1_DMA_CFN(n) (0x40 * (n) + 0x12) +#define OMAP1_DMA_CSFI(n) (0x40 * (n) + 0x14) +#define OMAP1_DMA_CSEI(n) (0x40 * (n) + 0x16) +#define OMAP1_DMA_CPC(n) (0x40 * (n) + 0x18) /* 15xx only */ +#define OMAP1_DMA_CSAC(n) (0x40 * (n) + 0x18) +#define OMAP1_DMA_CDAC(n) (0x40 * (n) + 0x1a) +#define OMAP1_DMA_CDEI(n) (0x40 * (n) + 0x1c) +#define OMAP1_DMA_CDFI(n) (0x40 * (n) + 0x1e) +#define OMAP1_DMA_CLNK_CTRL(n) (0x40 * (n) + 0x28) /* Common channel specific registers for omap2 */ -#define OMAP_DMA_CCR_REG(n) __REG32(OMAP_DMA4_BASE + 0x60 * (n) + 0x80) -#define OMAP_DMA_CLNK_CTRL_REG(n) __REG32(OMAP_DMA4_BASE + 0x60 * (n) + 0x84) -#define OMAP_DMA_CICR_REG(n) __REG32(OMAP_DMA4_BASE + 0x60 * (n) + 0x88) -#define OMAP_DMA_CSR_REG(n) __REG32(OMAP_DMA4_BASE + 0x60 * (n) + 0x8c) -#define OMAP_DMA_CSDP_REG(n) __REG32(OMAP_DMA4_BASE + 0x60 * (n) + 0x90) -#define OMAP_DMA_CEN_REG(n) __REG32(OMAP_DMA4_BASE + 0x60 * (n) + 0x94) -#define OMAP_DMA_CFN_REG(n) __REG32(OMAP_DMA4_BASE + 0x60 * (n) + 0x98) -#define OMAP_DMA_CSEI_REG(n) __REG32(OMAP_DMA4_BASE + 0x60 * (n) + 0xa4) -#define OMAP_DMA_CSFI_REG(n) __REG32(OMAP_DMA4_BASE + 0x60 * (n) + 0xa8) -#define OMAP_DMA_CDEI_REG(n) __REG32(OMAP_DMA4_BASE + 0x60 * (n) + 0xac) -#define OMAP_DMA_CDFI_REG(n) __REG32(OMAP_DMA4_BASE + 0x60 * (n) + 0xb0) -#define OMAP_DMA_CSAC_REG(n) __REG32(OMAP_DMA4_BASE + 0x60 * (n) + 0xb4) -#define OMAP_DMA_CDAC_REG(n) __REG32(OMAP_DMA4_BASE + 0x60 * (n) + 0xb8) - -#endif +#define OMAP_DMA4_CH_BASE(n) (0x60 * (n) + 0x80) +#define OMAP_DMA4_CCR(n) (0x60 * (n) + 0x80) +#define OMAP_DMA4_CLNK_CTRL(n) (0x60 * (n) + 0x84) +#define OMAP_DMA4_CICR(n) (0x60 * (n) + 0x88) +#define OMAP_DMA4_CSR(n) (0x60 * (n) + 0x8c) +#define OMAP_DMA4_CSDP(n) (0x60 * (n) + 0x90) +#define OMAP_DMA4_CEN(n) (0x60 * (n) + 0x94) +#define OMAP_DMA4_CFN(n) (0x60 * (n) + 0x98) +#define OMAP_DMA4_CSEI(n) (0x60 * (n) + 0xa4) +#define OMAP_DMA4_CSFI(n) (0x60 * (n) + 0xa8) +#define OMAP_DMA4_CDEI(n) (0x60 * (n) + 0xac) +#define OMAP_DMA4_CDFI(n) (0x60 * (n) + 0xb0) +#define OMAP_DMA4_CSAC(n) (0x60 * (n) + 0xb4) +#define OMAP_DMA4_CDAC(n) (0x60 * (n) + 0xb8) /* Channel specific registers only on omap1 */ -#define OMAP1_DMA_CSSA_L_REG(n) __REG16(OMAP_DMA_BASE + 0x40 * (n) + 0x08) -#define OMAP1_DMA_CSSA_U_REG(n) __REG16(OMAP_DMA_BASE + 0x40 * (n) + 0x0a) -#define OMAP1_DMA_CDSA_L_REG(n) __REG16(OMAP_DMA_BASE + 0x40 * (n) + 0x0c) -#define OMAP1_DMA_CDSA_U_REG(n) __REG16(OMAP_DMA_BASE + 0x40 * (n) + 0x0e) -#define OMAP1_DMA_COLOR_L_REG(n) __REG16(OMAP_DMA_BASE + 0x40 * (n) + 0x20) -#define OMAP1_DMA_CCR2_REG(n) __REG16(OMAP_DMA_BASE + 0x40 * (n) + 0x24) -#define OMAP1_DMA_COLOR_U_REG(n) __REG16(OMAP_DMA_BASE + 0x40 * (n) + 0x22) -#define OMAP1_DMA_LCH_CTRL_REG(n) __REG16(OMAP_DMA_BASE + 0x40 * (n) + 0x2a) +#define OMAP1_DMA_CSSA_L(n) (0x40 * (n) + 0x08) +#define OMAP1_DMA_CSSA_U(n) (0x40 * (n) + 0x0a) +#define OMAP1_DMA_CDSA_L(n) (0x40 * (n) + 0x0c) +#define OMAP1_DMA_CDSA_U(n) (0x40 * (n) + 0x0e) +#define OMAP1_DMA_COLOR_L(n) (0x40 * (n) + 0x20) +#define OMAP1_DMA_COLOR_U(n) (0x40 * (n) + 0x22) +#define OMAP1_DMA_CCR2(n) (0x40 * (n) + 0x24) +#define OMAP1_DMA_LCH_CTRL(n) (0x40 * (n) + 0x2a) /* not on 15xx */ +#define OMAP1_DMA_CCEN(n) 0 +#define OMAP1_DMA_CCFN(n) 0 /* Channel specific registers only on omap2 */ -#define OMAP2_DMA_CSSA_REG(n) __REG32(OMAP_DMA4_BASE + 0x60 * (n) + 0x9c) -#define OMAP2_DMA_CDSA_REG(n) __REG32(OMAP_DMA4_BASE + 0x60 * (n) + 0xa0) -#define OMAP2_DMA_CCEN_REG(n) __REG32(OMAP_DMA4_BASE + 0x60 * (n) + 0xbc) -#define OMAP2_DMA_CCFN_REG(n) __REG32(OMAP_DMA4_BASE + 0x60 * (n) + 0xc0) -#define OMAP2_DMA_COLOR_REG(n) __REG32(OMAP_DMA4_BASE + 0x60 * (n) + 0xc4) +#define OMAP_DMA4_CSSA(n) (0x60 * (n) + 0x9c) +#define OMAP_DMA4_CDSA(n) (0x60 * (n) + 0xa0) +#define OMAP_DMA4_CCEN(n) (0x60 * (n) + 0xbc) +#define OMAP_DMA4_CCFN(n) (0x60 * (n) + 0xc0) +#define OMAP_DMA4_COLOR(n) (0x60 * (n) + 0xc4) + +/* Dummy defines to keep multi-omap compiles happy */ +#define OMAP1_DMA_REVISION 0 +#define OMAP1_DMA_IRQSTATUS_L0 0 +#define OMAP1_DMA_IRQENABLE_L0 0 +#define OMAP1_DMA_OCP_SYSCONFIG 0 +#define OMAP_DMA4_HW_ID 0 +#define OMAP_DMA4_CAPS_0_L 0 +#define OMAP_DMA4_CAPS_0_U 0 +#define OMAP_DMA4_CAPS_1_L 0 +#define OMAP_DMA4_CAPS_1_U 0 +#define OMAP_DMA4_GSCR 0 +#define OMAP_DMA4_CPC(n) 0 + +#define OMAP_DMA4_LCH_CTRL(n) 0 +#define OMAP_DMA4_COLOR_L(n) 0 +#define OMAP_DMA4_COLOR_U(n) 0 +#define OMAP_DMA4_CCR2(n) 0 +#define OMAP1_DMA_CSSA(n) 0 +#define OMAP1_DMA_CDSA(n) 0 +#define OMAP_DMA4_CSSA_L(n) 0 +#define OMAP_DMA4_CSSA_U(n) 0 +#define OMAP_DMA4_CDSA_L(n) 0 +#define OMAP_DMA4_CDSA_U(n) 0 /*----------------------------------------------------------------------------*/ @@ -196,63 +216,98 @@ #define OMAP24XX_DMA_GPMC 4 /* S_DMA_3 */ #define OMAP24XX_DMA_GFX 5 /* S_DMA_4 */ #define OMAP24XX_DMA_DSS 6 /* S_DMA_5 */ -#define OMAP24XX_DMA_VLYNQ_TX 7 /* S_DMA_6 */ +#define OMAP242X_DMA_VLYNQ_TX 7 /* S_DMA_6 */ +#define OMAP24XX_DMA_EXT_DMAREQ2 7 /* S_DMA_6 */ #define OMAP24XX_DMA_CWT 8 /* S_DMA_7 */ #define OMAP24XX_DMA_AES_TX 9 /* S_DMA_8 */ #define OMAP24XX_DMA_AES_RX 10 /* S_DMA_9 */ #define OMAP24XX_DMA_DES_TX 11 /* S_DMA_10 */ #define OMAP24XX_DMA_DES_RX 12 /* S_DMA_11 */ #define OMAP24XX_DMA_SHA1MD5_RX 13 /* S_DMA_12 */ -#define OMAP24XX_DMA_EXT_DMAREQ2 14 /* S_DMA_13 */ -#define OMAP24XX_DMA_EXT_DMAREQ3 15 /* S_DMA_14 */ -#define OMAP24XX_DMA_EXT_DMAREQ4 16 /* S_DMA_15 */ -#define OMAP24XX_DMA_EAC_AC_RD 17 /* S_DMA_16 */ -#define OMAP24XX_DMA_EAC_AC_WR 18 /* S_DMA_17 */ -#define OMAP24XX_DMA_EAC_MD_UL_RD 19 /* S_DMA_18 */ -#define OMAP24XX_DMA_EAC_MD_UL_WR 20 /* S_DMA_19 */ -#define OMAP24XX_DMA_EAC_MD_DL_RD 21 /* S_DMA_20 */ -#define OMAP24XX_DMA_EAC_MD_DL_WR 22 /* S_DMA_21 */ -#define OMAP24XX_DMA_EAC_BT_UL_RD 23 /* S_DMA_22 */ -#define OMAP24XX_DMA_EAC_BT_UL_WR 24 /* S_DMA_23 */ -#define OMAP24XX_DMA_EAC_BT_DL_RD 25 /* S_DMA_24 */ -#define OMAP24XX_DMA_EAC_BT_DL_WR 26 /* S_DMA_25 */ +#define OMAP34XX_DMA_SHA2MD5_RX 13 /* S_DMA_12 */ +#define OMAP242X_DMA_EXT_DMAREQ2 14 /* S_DMA_13 */ +#define OMAP242X_DMA_EXT_DMAREQ3 15 /* S_DMA_14 */ +#define OMAP242X_DMA_EXT_DMAREQ4 16 /* S_DMA_15 */ +#define OMAP242X_DMA_EAC_AC_RD 17 /* S_DMA_16 */ +#define OMAP242X_DMA_EAC_AC_WR 18 /* S_DMA_17 */ +#define OMAP242X_DMA_EAC_MD_UL_RD 19 /* S_DMA_18 */ +#define OMAP242X_DMA_EAC_MD_UL_WR 20 /* S_DMA_19 */ +#define OMAP242X_DMA_EAC_MD_DL_RD 21 /* S_DMA_20 */ +#define OMAP242X_DMA_EAC_MD_DL_WR 22 /* S_DMA_21 */ +#define OMAP242X_DMA_EAC_BT_UL_RD 23 /* S_DMA_22 */ +#define OMAP242X_DMA_EAC_BT_UL_WR 24 /* S_DMA_23 */ +#define OMAP242X_DMA_EAC_BT_DL_RD 25 /* S_DMA_24 */ +#define OMAP242X_DMA_EAC_BT_DL_WR 26 /* S_DMA_25 */ +#define OMAP243X_DMA_EXT_DMAREQ3 14 /* S_DMA_13 */ +#define OMAP24XX_DMA_SPI3_TX0 15 /* S_DMA_14 */ +#define OMAP24XX_DMA_SPI3_RX0 16 /* S_DMA_15 */ +#define OMAP24XX_DMA_MCBSP3_TX 17 /* S_DMA_16 */ +#define OMAP24XX_DMA_MCBSP3_RX 18 /* S_DMA_17 */ +#define OMAP24XX_DMA_MCBSP4_TX 19 /* S_DMA_18 */ +#define OMAP24XX_DMA_MCBSP4_RX 20 /* S_DMA_19 */ +#define OMAP24XX_DMA_MCBSP5_TX 21 /* S_DMA_20 */ +#define OMAP24XX_DMA_MCBSP5_RX 22 /* S_DMA_21 */ +#define OMAP24XX_DMA_SPI3_TX1 23 /* S_DMA_22 */ +#define OMAP24XX_DMA_SPI3_RX1 24 /* S_DMA_23 */ +#define OMAP243X_DMA_EXT_DMAREQ4 25 /* S_DMA_24 */ +#define OMAP243X_DMA_EXT_DMAREQ5 26 /* S_DMA_25 */ +#define OMAP34XX_DMA_I2C3_TX 25 /* S_DMA_24 */ +#define OMAP34XX_DMA_I2C3_RX 26 /* S_DMA_25 */ #define OMAP24XX_DMA_I2C1_TX 27 /* S_DMA_26 */ #define OMAP24XX_DMA_I2C1_RX 28 /* S_DMA_27 */ #define OMAP24XX_DMA_I2C2_TX 29 /* S_DMA_28 */ #define OMAP24XX_DMA_I2C2_RX 30 /* S_DMA_29 */ -#define OMAP24XX_DMA_MCBSP1_TX 31 /* SDMA_30 */ -#define OMAP24XX_DMA_MCBSP1_RX 32 /* SDMA_31 */ -#define OMAP24XX_DMA_MCBSP2_TX 33 /* SDMA_32 */ -#define OMAP24XX_DMA_MCBSP2_RX 34 /* SDMA_33 */ -#define OMAP24XX_DMA_SPI1_TX0 35 /* SDMA_34 */ -#define OMAP24XX_DMA_SPI1_RX0 36 /* SDMA_35 */ -#define OMAP24XX_DMA_SPI1_TX1 37 /* SDMA_36 */ -#define OMAP24XX_DMA_SPI1_RX1 38 /* SDMA_37 */ -#define OMAP24XX_DMA_SPI1_TX2 39 /* SDMA_38 */ -#define OMAP24XX_DMA_SPI1_RX2 40 /* SDMA_39 */ -#define OMAP24XX_DMA_SPI1_TX3 41 /* SDMA_40 */ -#define OMAP24XX_DMA_SPI1_RX3 42 /* SDMA_41 */ -#define OMAP24XX_DMA_SPI2_TX0 43 /* SDMA_42 */ -#define OMAP24XX_DMA_SPI2_RX0 44 /* SDMA_43 */ -#define OMAP24XX_DMA_SPI2_TX1 45 /* SDMA_44 */ -#define OMAP24XX_DMA_SPI2_RX1 46 /* SDMA_45 */ - -#define OMAP24XX_DMA_UART1_TX 49 /* SDMA_48 */ -#define OMAP24XX_DMA_UART1_RX 50 /* SDMA_49 */ -#define OMAP24XX_DMA_UART2_TX 51 /* SDMA_50 */ -#define OMAP24XX_DMA_UART2_RX 52 /* SDMA_51 */ -#define OMAP24XX_DMA_UART3_TX 53 /* SDMA_52 */ -#define OMAP24XX_DMA_UART3_RX 54 /* SDMA_53 */ -#define OMAP24XX_DMA_USB_W2FC_TX0 55 /* SDMA_54 */ -#define OMAP24XX_DMA_USB_W2FC_RX0 56 /* SDMA_55 */ -#define OMAP24XX_DMA_USB_W2FC_TX1 57 /* SDMA_56 */ -#define OMAP24XX_DMA_USB_W2FC_RX1 58 /* SDMA_57 */ -#define OMAP24XX_DMA_USB_W2FC_TX2 59 /* SDMA_58 */ -#define OMAP24XX_DMA_USB_W2FC_RX2 60 /* SDMA_59 */ -#define OMAP24XX_DMA_MMC1_TX 61 /* SDMA_60 */ -#define OMAP24XX_DMA_MMC1_RX 62 /* SDMA_61 */ -#define OMAP24XX_DMA_MS 63 /* SDMA_62 */ -#define OMAP24XX_DMA_EXT_DMAREQ5 64 /* S_DMA_63 */ +#define OMAP24XX_DMA_MCBSP1_TX 31 /* S_DMA_30 */ +#define OMAP24XX_DMA_MCBSP1_RX 32 /* S_DMA_31 */ +#define OMAP24XX_DMA_MCBSP2_TX 33 /* S_DMA_32 */ +#define OMAP24XX_DMA_MCBSP2_RX 34 /* S_DMA_33 */ +#define OMAP24XX_DMA_SPI1_TX0 35 /* S_DMA_34 */ +#define OMAP24XX_DMA_SPI1_RX0 36 /* S_DMA_35 */ +#define OMAP24XX_DMA_SPI1_TX1 37 /* S_DMA_36 */ +#define OMAP24XX_DMA_SPI1_RX1 38 /* S_DMA_37 */ +#define OMAP24XX_DMA_SPI1_TX2 39 /* S_DMA_38 */ +#define OMAP24XX_DMA_SPI1_RX2 40 /* S_DMA_39 */ +#define OMAP24XX_DMA_SPI1_TX3 41 /* S_DMA_40 */ +#define OMAP24XX_DMA_SPI1_RX3 42 /* S_DMA_41 */ +#define OMAP24XX_DMA_SPI2_TX0 43 /* S_DMA_42 */ +#define OMAP24XX_DMA_SPI2_RX0 44 /* S_DMA_43 */ +#define OMAP24XX_DMA_SPI2_TX1 45 /* S_DMA_44 */ +#define OMAP24XX_DMA_SPI2_RX1 46 /* S_DMA_45 */ +#define OMAP24XX_DMA_MMC2_TX 47 /* S_DMA_46 */ +#define OMAP24XX_DMA_MMC2_RX 48 /* S_DMA_47 */ +#define OMAP24XX_DMA_UART1_TX 49 /* S_DMA_48 */ +#define OMAP24XX_DMA_UART1_RX 50 /* S_DMA_49 */ +#define OMAP24XX_DMA_UART2_TX 51 /* S_DMA_50 */ +#define OMAP24XX_DMA_UART2_RX 52 /* S_DMA_51 */ +#define OMAP24XX_DMA_UART3_TX 53 /* S_DMA_52 */ +#define OMAP24XX_DMA_UART3_RX 54 /* S_DMA_53 */ +#define OMAP24XX_DMA_USB_W2FC_TX0 55 /* S_DMA_54 */ +#define OMAP24XX_DMA_USB_W2FC_RX0 56 /* S_DMA_55 */ +#define OMAP24XX_DMA_USB_W2FC_TX1 57 /* S_DMA_56 */ +#define OMAP24XX_DMA_USB_W2FC_RX1 58 /* S_DMA_57 */ +#define OMAP24XX_DMA_USB_W2FC_TX2 59 /* S_DMA_58 */ +#define OMAP24XX_DMA_USB_W2FC_RX2 60 /* S_DMA_59 */ +#define OMAP24XX_DMA_MMC1_TX 61 /* S_DMA_60 */ +#define OMAP24XX_DMA_MMC1_RX 62 /* S_DMA_61 */ +#define OMAP24XX_DMA_MS 63 /* S_DMA_62 */ +#define OMAP242X_DMA_EXT_DMAREQ5 64 /* S_DMA_63 */ +#define OMAP243X_DMA_EXT_DMAREQ6 64 /* S_DMA_63 */ +#define OMAP34XX_DMA_EXT_DMAREQ3 64 /* S_DMA_63 */ +#define OMAP34XX_DMA_AES2_TX 65 /* S_DMA_64 */ +#define OMAP34XX_DMA_AES2_RX 66 /* S_DMA_65 */ +#define OMAP34XX_DMA_DES2_TX 67 /* S_DMA_66 */ +#define OMAP34XX_DMA_DES2_RX 68 /* S_DMA_67 */ +#define OMAP34XX_DMA_SHA1MD5_RX 69 /* S_DMA_68 */ +#define OMAP34XX_DMA_SPI4_TX0 70 /* S_DMA_69 */ +#define OMAP34XX_DMA_SPI4_RX0 71 /* S_DMA_70 */ +#define OMAP34XX_DSS_DMA0 72 /* S_DMA_71 */ +#define OMAP34XX_DSS_DMA1 73 /* S_DMA_72 */ +#define OMAP34XX_DSS_DMA2 74 /* S_DMA_73 */ +#define OMAP34XX_DSS_DMA3 75 /* S_DMA_74 */ +#define OMAP34XX_DMA_MMC3_TX 77 /* S_DMA_76 */ +#define OMAP34XX_DMA_MMC3_RX 78 /* S_DMA_77 */ +#define OMAP34XX_DMA_USIM_TX 79 /* S_DMA_78 */ +#define OMAP34XX_DMA_USIM_RX 80 /* S_DMA_79 */ /*----------------------------------------------------------------------------*/ @@ -358,6 +413,11 @@ enum omap_dma_burst_mode { OMAP_DMA_DATA_BURST_16, }; +enum end_type { + OMAP_DMA_LITTLE_ENDIAN = 0, + OMAP_DMA_BIG_ENDIAN +}; + enum omap_dma_color_mode { OMAP_DMA_COLOR_DIS = 0, OMAP_DMA_CONSTANT_FILL, @@ -370,24 +430,34 @@ enum omap_dma_write_mode { OMAP_DMA_WRITE_LAST_NON_POSTED }; +enum omap_dma_channel_mode { + OMAP_DMA_LCH_2D = 0, + OMAP_DMA_LCH_G, + OMAP_DMA_LCH_P, + OMAP_DMA_LCH_PD +}; + struct omap_dma_channel_params { int data_type; /* data type 8,16,32 */ int elem_count; /* number of elements in a frame */ int frame_count; /* number of frames in a element */ int src_port; /* Only on OMAP1 REVISIT: Is this needed? */ - int src_amode; /* constant , post increment, indexed , double indexed */ + int src_amode; /* constant, post increment, indexed, + double indexed */ unsigned long src_start; /* source address : physical */ int src_ei; /* source element index */ int src_fi; /* source frame index */ int dst_port; /* Only on OMAP1 REVISIT: Is this needed? */ - int dst_amode; /* constant , post increment, indexed , double indexed */ + int dst_amode; /* constant, post increment, indexed, + double indexed */ unsigned long dst_start; /* source address : physical */ int dst_ei; /* source element index */ int dst_fi; /* source frame index */ - int trigger; /* trigger attached if the channel is synchronized */ + int trigger; /* trigger attached if the channel is + synchronized */ int sync_mode; /* sycn on element, frame , block or packet */ int src_or_dst_synch; /* source synch(1) or destination synch(0) */ @@ -404,8 +474,8 @@ struct omap_dma_channel_params { extern void omap_set_dma_priority(int lch, int dst_port, int priority); extern int omap_request_dma(int dev_id, const char *dev_name, - void (* callback)(int lch, u16 ch_status, void *data), - void *data, int *dma_ch); + void (*callback)(int lch, u16 ch_status, void *data), + void *data, int *dma_ch); extern void omap_enable_dma_irq(int ch, u16 irq_bits); extern void omap_disable_dma_irq(int ch, u16 irq_bits); extern void omap_free_dma(int ch); @@ -418,6 +488,7 @@ extern void omap_set_dma_transfer_params(int lch, int data_type, extern void omap_set_dma_color_mode(int lch, enum omap_dma_color_mode mode, u32 color); extern void omap_set_dma_write_mode(int lch, enum omap_dma_write_mode mode); +extern void omap_set_dma_channel_mode(int lch, enum omap_dma_channel_mode mode); extern void omap_set_dma_src_params(int lch, int src_port, int src_amode, unsigned long src_start, @@ -436,23 +507,26 @@ extern void omap_set_dma_dest_burst_mode(int lch, enum omap_dma_burst_mode burst_mode); extern void omap_set_dma_params(int lch, - struct omap_dma_channel_params * params); + struct omap_dma_channel_params *params); -extern void omap_dma_link_lch (int lch_head, int lch_queue); -extern void omap_dma_unlink_lch (int lch_head, int lch_queue); +extern void omap_dma_link_lch(int lch_head, int lch_queue); +extern void omap_dma_unlink_lch(int lch_head, int lch_queue); extern int omap_set_dma_callback(int lch, - void (* callback)(int lch, u16 ch_status, void *data), + void (*callback)(int lch, u16 ch_status, void *data), void *data); extern dma_addr_t omap_get_dma_src_pos(int lch); extern dma_addr_t omap_get_dma_dst_pos(int lch); -extern int omap_get_dma_src_addr_counter(int lch); extern void omap_clear_dma(int lch); +extern int omap_get_dma_active_status(int lch); extern int omap_dma_running(void); extern void omap_dma_set_global_params(int arb_rate, int max_fifo_depth, int tparams); extern int omap_dma_set_prio_lch(int lch, unsigned char read_prio, unsigned char write_prio); +extern void omap_set_dma_dst_endian_type(int lch, enum end_type etype); +extern void omap_set_dma_src_endian_type(int lch, enum end_type etype); +extern int omap_get_dma_index(int lch, int *ei, int *fi); /* Chaining APIs */ #ifndef CONFIG_ARCH_OMAP1 @@ -478,7 +552,7 @@ extern int omap_dma_chain_status(int chain_id); #endif /* LCD DMA functions */ -extern int omap_request_lcd_dma(void (* callback)(u16 status, void *data), +extern int omap_request_lcd_dma(void (*callback)(u16 status, void *data), void *data); extern void omap_free_lcd_dma(void); extern void omap_setup_lcd_dma(void); diff --git a/include/asm-arm/arch-omap/dmtimer.h b/include/asm-arm/arch-omap/dmtimer.h index fefb276ed40..02b29e8437a 100644 --- a/include/asm-arm/arch-omap/dmtimer.h +++ b/include/asm-arm/arch-omap/dmtimer.h @@ -66,6 +66,7 @@ void omap_dm_timer_stop(struct omap_dm_timer *timer); void omap_dm_timer_set_source(struct omap_dm_timer *timer, int source); void omap_dm_timer_set_load(struct omap_dm_timer *timer, int autoreload, unsigned int value); +void omap_dm_timer_set_load_start(struct omap_dm_timer *timer, int autoreload, unsigned int value); void omap_dm_timer_set_match(struct omap_dm_timer *timer, int enable, unsigned int match); void omap_dm_timer_set_pwm(struct omap_dm_timer *timer, int def_on, int toggle, int trigger); void omap_dm_timer_set_prescaler(struct omap_dm_timer *timer, int prescaler); diff --git a/include/asm-arm/arch-omap/fpga.h b/include/asm-arm/arch-omap/fpga.h index 6a883e0bdbb..f420881d2a3 100644 --- a/include/asm-arm/arch-omap/fpga.h +++ b/include/asm-arm/arch-omap/fpga.h @@ -169,30 +169,29 @@ struct h2p2_dbg_fpga { #define OMAP1510_INT_FPGA (IH_GPIO_BASE + 13) /* IRQ Numbers for interrupts muxed through the FPGA */ -#define OMAP1510_IH_FPGA_BASE IH_BOARD_BASE -#define OMAP1510_INT_FPGA_ATN (OMAP1510_IH_FPGA_BASE + 0) -#define OMAP1510_INT_FPGA_ACK (OMAP1510_IH_FPGA_BASE + 1) -#define OMAP1510_INT_FPGA2 (OMAP1510_IH_FPGA_BASE + 2) -#define OMAP1510_INT_FPGA3 (OMAP1510_IH_FPGA_BASE + 3) -#define OMAP1510_INT_FPGA4 (OMAP1510_IH_FPGA_BASE + 4) -#define OMAP1510_INT_FPGA5 (OMAP1510_IH_FPGA_BASE + 5) -#define OMAP1510_INT_FPGA6 (OMAP1510_IH_FPGA_BASE + 6) -#define OMAP1510_INT_FPGA7 (OMAP1510_IH_FPGA_BASE + 7) -#define OMAP1510_INT_FPGA8 (OMAP1510_IH_FPGA_BASE + 8) -#define OMAP1510_INT_FPGA9 (OMAP1510_IH_FPGA_BASE + 9) -#define OMAP1510_INT_FPGA10 (OMAP1510_IH_FPGA_BASE + 10) -#define OMAP1510_INT_FPGA11 (OMAP1510_IH_FPGA_BASE + 11) -#define OMAP1510_INT_FPGA12 (OMAP1510_IH_FPGA_BASE + 12) -#define OMAP1510_INT_ETHER (OMAP1510_IH_FPGA_BASE + 13) -#define OMAP1510_INT_FPGAUART1 (OMAP1510_IH_FPGA_BASE + 14) -#define OMAP1510_INT_FPGAUART2 (OMAP1510_IH_FPGA_BASE + 15) -#define OMAP1510_INT_FPGA_TS (OMAP1510_IH_FPGA_BASE + 16) -#define OMAP1510_INT_FPGA17 (OMAP1510_IH_FPGA_BASE + 17) -#define OMAP1510_INT_FPGA_CAM (OMAP1510_IH_FPGA_BASE + 18) -#define OMAP1510_INT_FPGA_RTC_A (OMAP1510_IH_FPGA_BASE + 19) -#define OMAP1510_INT_FPGA_RTC_B (OMAP1510_IH_FPGA_BASE + 20) -#define OMAP1510_INT_FPGA_CD (OMAP1510_IH_FPGA_BASE + 21) -#define OMAP1510_INT_FPGA22 (OMAP1510_IH_FPGA_BASE + 22) -#define OMAP1510_INT_FPGA23 (OMAP1510_IH_FPGA_BASE + 23) +#define OMAP1510_INT_FPGA_ATN (OMAP_FPGA_IRQ_BASE + 0) +#define OMAP1510_INT_FPGA_ACK (OMAP_FPGA_IRQ_BASE + 1) +#define OMAP1510_INT_FPGA2 (OMAP_FPGA_IRQ_BASE + 2) +#define OMAP1510_INT_FPGA3 (OMAP_FPGA_IRQ_BASE + 3) +#define OMAP1510_INT_FPGA4 (OMAP_FPGA_IRQ_BASE + 4) +#define OMAP1510_INT_FPGA5 (OMAP_FPGA_IRQ_BASE + 5) +#define OMAP1510_INT_FPGA6 (OMAP_FPGA_IRQ_BASE + 6) +#define OMAP1510_INT_FPGA7 (OMAP_FPGA_IRQ_BASE + 7) +#define OMAP1510_INT_FPGA8 (OMAP_FPGA_IRQ_BASE + 8) +#define OMAP1510_INT_FPGA9 (OMAP_FPGA_IRQ_BASE + 9) +#define OMAP1510_INT_FPGA10 (OMAP_FPGA_IRQ_BASE + 10) +#define OMAP1510_INT_FPGA11 (OMAP_FPGA_IRQ_BASE + 11) +#define OMAP1510_INT_FPGA12 (OMAP_FPGA_IRQ_BASE + 12) +#define OMAP1510_INT_ETHER (OMAP_FPGA_IRQ_BASE + 13) +#define OMAP1510_INT_FPGAUART1 (OMAP_FPGA_IRQ_BASE + 14) +#define OMAP1510_INT_FPGAUART2 (OMAP_FPGA_IRQ_BASE + 15) +#define OMAP1510_INT_FPGA_TS (OMAP_FPGA_IRQ_BASE + 16) +#define OMAP1510_INT_FPGA17 (OMAP_FPGA_IRQ_BASE + 17) +#define OMAP1510_INT_FPGA_CAM (OMAP_FPGA_IRQ_BASE + 18) +#define OMAP1510_INT_FPGA_RTC_A (OMAP_FPGA_IRQ_BASE + 19) +#define OMAP1510_INT_FPGA_RTC_B (OMAP_FPGA_IRQ_BASE + 20) +#define OMAP1510_INT_FPGA_CD (OMAP_FPGA_IRQ_BASE + 21) +#define OMAP1510_INT_FPGA22 (OMAP_FPGA_IRQ_BASE + 22) +#define OMAP1510_INT_FPGA23 (OMAP_FPGA_IRQ_BASE + 23) #endif diff --git a/include/asm-arm/arch-omap/hardware.h b/include/asm-arm/arch-omap/hardware.h index 91d85b3417b..45fdfccbd5d 100644 --- a/include/asm-arm/arch-omap/hardware.h +++ b/include/asm-arm/arch-omap/hardware.h @@ -284,6 +284,7 @@ #include "omap1510.h" #include "omap24xx.h" #include "omap16xx.h" +#include "omap34xx.h" #ifndef __ASSEMBLER__ diff --git a/include/asm-arm/arch-omap/io.h b/include/asm-arm/arch-omap/io.h index 160578e1f55..0b13557fd30 100644 --- a/include/asm-arm/arch-omap/io.h +++ b/include/asm-arm/arch-omap/io.h @@ -60,6 +60,7 @@ #define IO_SIZE 0x40000 #define IO_VIRT (IO_PHYS - IO_OFFSET) #define IO_ADDRESS(pa) ((pa) - IO_OFFSET) +#define OMAP1_IO_ADDRESS(pa) ((pa) - IO_OFFSET) #define io_p2v(pa) ((pa) - IO_OFFSET) #define io_v2p(va) ((va) + IO_OFFSET) @@ -91,6 +92,7 @@ #define IO_OFFSET 0x90000000 #define IO_ADDRESS(pa) ((pa) + IO_OFFSET) /* Works for L3 and L4 */ +#define OMAP2_IO_ADDRESS(pa) ((pa) + IO_OFFSET) /* Works for L3 and L4 */ #define io_p2v(pa) ((pa) + IO_OFFSET) /* Works for L3 and L4 */ #define io_v2p(va) ((va) - IO_OFFSET) /* Works for L3 and L4 */ @@ -148,6 +150,7 @@ #define IO_OFFSET 0x90000000 #define IO_ADDRESS(pa) ((pa) + IO_OFFSET)/* Works for L3 and L4 */ +#define OMAP2_IO_ADDRESS(pa) ((pa) + IO_OFFSET)/* Works for L3 and L4 */ #define io_p2v(pa) ((pa) + IO_OFFSET)/* Works for L3 and L4 */ #define io_v2p(va) ((va) - IO_OFFSET)/* Works for L3 and L4 */ @@ -183,35 +186,12 @@ #define omap_writew(v,a) (*(volatile unsigned short *)IO_ADDRESS(a) = (v)) #define omap_writel(v,a) (*(volatile unsigned int *)IO_ADDRESS(a) = (v)) -/* 16 bit uses LDRH/STRH, base +/- offset_8 */ -typedef struct { volatile u16 offset[256]; } __regbase16; -#define __REGV16(vaddr) ((__regbase16 *)((vaddr)&~0xff)) \ - ->offset[((vaddr)&0xff)>>1] -#define __REG16(paddr) __REGV16(io_p2v(paddr)) - -/* 8/32 bit uses LDR/STR, base +/- offset_12 */ -typedef struct { volatile u8 offset[4096]; } __regbase8; -#define __REGV8(vaddr) ((__regbase8 *)((vaddr)&~4095)) \ - ->offset[((vaddr)&4095)>>0] -#define __REG8(paddr) __REGV8(io_p2v(paddr)) - -typedef struct { volatile u32 offset[4096]; } __regbase32; -#define __REGV32(vaddr) ((__regbase32 *)((vaddr)&~4095)) \ - ->offset[((vaddr)&4095)>>2] -#define __REG32(paddr) __REGV32(io_p2v(paddr)) - extern void omap1_map_common_io(void); extern void omap1_init_common_hw(void); extern void omap2_map_common_io(void); extern void omap2_init_common_hw(void); -#else - -#define __REG8(paddr) io_p2v(paddr) -#define __REG16(paddr) io_p2v(paddr) -#define __REG32(paddr) io_p2v(paddr) - #endif #endif diff --git a/include/asm-arm/arch-omap/irqs.h b/include/asm-arm/arch-omap/irqs.h index 87973654e62..7464c694859 100644 --- a/include/asm-arm/arch-omap/irqs.h +++ b/include/asm-arm/arch-omap/irqs.h @@ -285,7 +285,41 @@ #define OMAP_MAX_GPIO_LINES 192 #define IH_GPIO_BASE (128 + IH2_BASE) #define IH_MPUIO_BASE (OMAP_MAX_GPIO_LINES + IH_GPIO_BASE) -#define IH_BOARD_BASE (16 + IH_MPUIO_BASE) +#define OMAP_IRQ_END (IH_MPUIO_BASE + 16) + +/* External FPGA handles interrupts on Innovator boards */ +#define OMAP_FPGA_IRQ_BASE (OMAP_IRQ_END) +#ifdef CONFIG_MACH_OMAP_INNOVATOR +#define OMAP_FPGA_NR_IRQS 24 +#else +#define OMAP_FPGA_NR_IRQS 0 +#endif +#define OMAP_FPGA_IRQ_END (OMAP_FPGA_IRQ_BASE + OMAP_FPGA_NR_IRQS) + +/* External TWL4030 can handle interrupts on 2430 and 34xx boards */ +#define TWL4030_IRQ_BASE (OMAP_FPGA_IRQ_END) +#ifdef CONFIG_TWL4030_CORE +#define TWL4030_BASE_NR_IRQS 8 +#define TWL4030_PWR_NR_IRQS 8 +#else +#define TWL4030_BASE_NR_IRQS 0 +#define TWL4030_PWR_NR_IRQS 0 +#endif +#define TWL4030_IRQ_END (TWL4030_IRQ_BASE + TWL4030_BASE_NR_IRQS) +#define TWL4030_PWR_IRQ_BASE TWL4030_IRQ_END +#define TWL4030_PWR_IRQ_END (TWL4030_PWR_IRQ_BASE + TWL4030_PWR_NR_IRQS) + +/* External TWL4030 gpio interrupts are optional */ +#define TWL4030_GPIO_IRQ_BASE TWL4030_PWR_IRQ_END +#ifdef CONFIG_TWL4030_GPIO +#define TWL4030_GPIO_NR_IRQS 18 +#else +#define TWL4030_GPIO_NR_IRQS 0 +#endif +#define TWL4030_GPIO_IRQ_END (TWL4030_GPIO_IRQ_BASE + TWL4030_GPIO_NR_IRQS) + +/* Total number of interrupts depends on the enabled blocks above */ +#define NR_IRQS TWL4030_GPIO_IRQ_END #define OMAP_IRQ_BIT(irq) (1 << ((irq) % 32)) @@ -293,14 +327,6 @@ extern void omap_init_irq(void); #endif -/* - * The definition of NR_IRQS is in board-specific header file, which is - * included via hardware.h - */ #include <asm/hardware.h> -#ifndef NR_IRQS -#define NR_IRQS IH_BOARD_BASE -#endif - #endif diff --git a/include/asm-arm/arch-omap/mcbsp.h b/include/asm-arm/arch-omap/mcbsp.h index c7a0cc1c4e9..26c78f67dc8 100644 --- a/include/asm-arm/arch-omap/mcbsp.h +++ b/include/asm-arm/arch-omap/mcbsp.h @@ -24,7 +24,11 @@ #ifndef __ASM_ARCH_OMAP_MCBSP_H #define __ASM_ARCH_OMAP_MCBSP_H +#include <linux/completion.h> +#include <linux/spinlock.h> + #include <asm/hardware.h> +#include <asm/arch/clock.h> #define OMAP730_MCBSP1_BASE 0xfffb1000 #define OMAP730_MCBSP2_BASE 0xfffb1800 @@ -40,6 +44,9 @@ #define OMAP24XX_MCBSP1_BASE 0x48074000 #define OMAP24XX_MCBSP2_BASE 0x48076000 +#define OMAP34XX_MCBSP1_BASE 0x48074000 +#define OMAP34XX_MCBSP2_BASE 0x49022000 + #if defined(CONFIG_ARCH_OMAP15XX) || defined(CONFIG_ARCH_OMAP16XX) || defined(CONFIG_ARCH_OMAP730) #define OMAP_MCBSP_REG_DRR2 0x00 @@ -74,7 +81,8 @@ #define OMAP_MCBSP_REG_XCERG 0x3A #define OMAP_MCBSP_REG_XCERH 0x3C -#define OMAP_MAX_MCBSP_COUNT 3 +#define OMAP_MAX_MCBSP_COUNT 3 +#define MAX_MCBSP_CLOCKS 3 #define AUDIO_MCBSP_DATAWRITE (OMAP1510_MCBSP1_BASE + OMAP_MCBSP_REG_DXR1) #define AUDIO_MCBSP_DATAREAD (OMAP1510_MCBSP1_BASE + OMAP_MCBSP_REG_DRR1) @@ -117,7 +125,8 @@ #define OMAP_MCBSP_REG_XCERG 0x74 #define OMAP_MCBSP_REG_XCERH 0x78 -#define OMAP_MAX_MCBSP_COUNT 2 +#define OMAP_MAX_MCBSP_COUNT 2 +#define MAX_MCBSP_CLOCKS 2 #define AUDIO_MCBSP_DATAWRITE (OMAP24XX_MCBSP2_BASE + OMAP_MCBSP_REG_DXR1) #define AUDIO_MCBSP_DATAREAD (OMAP24XX_MCBSP2_BASE + OMAP_MCBSP_REG_DRR1) @@ -298,6 +307,55 @@ struct omap_mcbsp_spi_cfg { omap_mcbsp_word_length word_length; }; +/* Platform specific configuration */ +struct omap_mcbsp_ops { + void (*request)(unsigned int); + void (*free)(unsigned int); + int (*check)(unsigned int); +}; + +struct omap_mcbsp_platform_data { + u32 virt_base; + u8 dma_rx_sync, dma_tx_sync; + u16 rx_irq, tx_irq; + struct omap_mcbsp_ops *ops; + char const *clk_name; +}; + +struct omap_mcbsp { + struct device *dev; + u32 io_base; + u8 id; + u8 free; + omap_mcbsp_word_length rx_word_length; + omap_mcbsp_word_length tx_word_length; + + omap_mcbsp_io_type_t io_type; /* IRQ or poll */ + /* IRQ based TX/RX */ + int rx_irq; + int tx_irq; + + /* DMA stuff */ + u8 dma_rx_sync; + short dma_rx_lch; + u8 dma_tx_sync; + short dma_tx_lch; + + /* Completion queues */ + struct completion tx_irq_completion; + struct completion rx_irq_completion; + struct completion tx_dma_completion; + struct completion rx_dma_completion; + + /* Protect the field .free, while checking if the mcbsp is in use */ + spinlock_t lock; + struct omap_mcbsp_platform_data *pdata; + struct clk *clk; +}; + +int omap_mcbsp_init(void); +void omap_mcbsp_register_board_cfg(struct omap_mcbsp_platform_data *config, + int size); void omap_mcbsp_config(unsigned int id, const struct omap_mcbsp_reg_cfg * config); int omap_mcbsp_request(unsigned int id); void omap_mcbsp_free(unsigned int id); diff --git a/include/asm-arm/arch-omap/omap34xx.h b/include/asm-arm/arch-omap/omap34xx.h new file mode 100644 index 00000000000..aa30c6d10ab --- /dev/null +++ b/include/asm-arm/arch-omap/omap34xx.h @@ -0,0 +1,72 @@ +/* + * include/asm-arm/arch-omap/omap34xx.h + * + * This file contains the processor specific definitions of the TI OMAP34XX. + * + * Copyright (C) 2007 Texas Instruments. + * Copyright (C) 2007 Nokia Corporation. + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA + */ + +#ifndef __ASM_ARCH_OMAP34XX_H +#define __ASM_ARCH_OMAP34XX_H + +/* + * Please place only base defines here and put the rest in device + * specific headers. + */ + +#define L4_34XX_BASE 0x48000000 +#define L4_WK_34XX_BASE 0x48300000 +#define L4_WK_OMAP_BASE L4_WK_34XX_BASE +#define L4_PER_34XX_BASE 0x49000000 +#define L4_PER_OMAP_BASE L4_PER_34XX_BASE +#define L4_EMU_34XX_BASE 0x54000000 +#define L4_EMU_BASE L4_EMU_34XX_BASE +#define L3_34XX_BASE 0x68000000 +#define L3_OMAP_BASE L3_34XX_BASE + +#define OMAP3430_32KSYNCT_BASE 0x48320000 +#define OMAP3430_CM_BASE 0x48004800 +#define OMAP3430_PRM_BASE 0x48306800 +#define OMAP343X_SMS_BASE 0x6C000000 +#define OMAP343X_SDRC_BASE 0x6D000000 +#define OMAP34XX_GPMC_BASE 0x6E000000 +#define OMAP343X_SCM_BASE 0x48002000 +#define OMAP343X_CTRL_BASE OMAP343X_SCM_BASE + +#define OMAP34XX_IC_BASE 0x48200000 +#define OMAP34XX_IVA_INTC_BASE 0x40000000 +#define OMAP34XX_HSUSB_OTG_BASE (L4_34XX_BASE + 0xAB000) +#define OMAP34XX_HSUSB_HOST_BASE (L4_34XX_BASE + 0x64000) +#define OMAP34XX_USBTLL_BASE (L4_34XX_BASE + 0x62000) + + +#if defined(CONFIG_ARCH_OMAP3430) + +#define OMAP2_32KSYNCT_BASE OMAP3430_32KSYNCT_BASE +#define OMAP2_CM_BASE OMAP3430_CM_BASE +#define OMAP2_PRM_BASE OMAP3430_PRM_BASE +#define OMAP2_VA_IC_BASE IO_ADDRESS(OMAP34XX_IC_BASE) + +#endif + +#define OMAP34XX_DSP_BASE 0x58000000 +#define OMAP34XX_DSP_MEM_BASE (OMAP34XX_DSP_BASE + 0x0) +#define OMAP34XX_DSP_IPI_BASE (OMAP34XX_DSP_BASE + 0x1000000) +#define OMAP34XX_DSP_MMU_BASE (OMAP34XX_DSP_BASE + 0x2000000) +#endif /* __ASM_ARCH_OMAP34XX_H */ + diff --git a/include/asm-arm/arch-omap/sram.h b/include/asm-arm/arch-omap/sram.h index bb9bb3fd532..be59f4a9828 100644 --- a/include/asm-arm/arch-omap/sram.h +++ b/include/asm-arm/arch-omap/sram.h @@ -11,6 +11,7 @@ #ifndef __ARCH_ARM_OMAP_SRAM_H #define __ARCH_ARM_OMAP_SRAM_H +extern int __init omap_sram_init(void); extern void * omap_sram_push(void * start, unsigned long size); extern void omap_sram_reprogram_clock(u32 dpllctl, u32 ckctl); @@ -21,17 +22,35 @@ extern void omap2_sram_reprogram_sdrc(u32 perf_level, u32 dll_val, extern u32 omap2_set_prcm(u32 dpll_ctrl_val, u32 sdrc_rfr_val, int bypass); /* Do not use these */ -extern void sram_reprogram_clock(u32 ckctl, u32 dpllctl); -extern unsigned long sram_reprogram_clock_sz; +extern void omap1_sram_reprogram_clock(u32 ckctl, u32 dpllctl); +extern unsigned long omap1_sram_reprogram_clock_sz; -extern void sram_ddr_init(u32 *slow_dll_ctrl, u32 fast_dll_ctrl, - u32 base_cs, u32 force_unlock); -extern unsigned long sram_ddr_init_sz; +extern void omap24xx_sram_reprogram_clock(u32 ckctl, u32 dpllctl); +extern unsigned long omap24xx_sram_reprogram_clock_sz; -extern u32 sram_set_prcm(u32 dpll_ctrl_val, u32 sdrc_rfr_val, int bypass); -extern unsigned long sram_set_prcm_sz; +extern void omap242x_sram_ddr_init(u32 *slow_dll_ctrl, u32 fast_dll_ctrl, + u32 base_cs, u32 force_unlock); +extern unsigned long omap242x_sram_ddr_init_sz; -extern void sram_reprogram_sdrc(u32 perf_level, u32 dll_val, u32 mem_type); -extern unsigned long sram_reprogram_sdrc_sz; +extern u32 omap242x_sram_set_prcm(u32 dpll_ctrl_val, u32 sdrc_rfr_val, + int bypass); +extern unsigned long omap242x_sram_set_prcm_sz; + +extern void omap242x_sram_reprogram_sdrc(u32 perf_level, u32 dll_val, + u32 mem_type); +extern unsigned long omap242x_sram_reprogram_sdrc_sz; + + +extern void omap243x_sram_ddr_init(u32 *slow_dll_ctrl, u32 fast_dll_ctrl, + u32 base_cs, u32 force_unlock); +extern unsigned long omap243x_sram_ddr_init_sz; + +extern u32 omap243x_sram_set_prcm(u32 dpll_ctrl_val, u32 sdrc_rfr_val, + int bypass); +extern unsigned long omap243x_sram_set_prcm_sz; + +extern void omap243x_sram_reprogram_sdrc(u32 perf_level, u32 dll_val, + u32 mem_type); +extern unsigned long omap243x_sram_reprogram_sdrc_sz; #endif diff --git a/include/asm-arm/arch-omap/tc.h b/include/asm-arm/arch-omap/tc.h index 8ded218cbea..65a9c82d3bf 100644 --- a/include/asm-arm/arch-omap/tc.h +++ b/include/asm-arm/arch-omap/tc.h @@ -75,16 +75,14 @@ #ifndef __ASSEMBLER__ /* EMIF Slow Interface Configuration Register */ -#define OMAP_EMIFS_CONFIG_REG __REG32(EMIFS_CONFIG) - #define OMAP_EMIFS_CONFIG_FR (1 << 4) #define OMAP_EMIFS_CONFIG_PDE (1 << 3) #define OMAP_EMIFS_CONFIG_PWD_EN (1 << 2) #define OMAP_EMIFS_CONFIG_BM (1 << 1) #define OMAP_EMIFS_CONFIG_WP (1 << 0) -#define EMIFS_CCS(n) __REG32(EMIFS_CS0_CONFIG + (4 * (n))) -#define EMIFS_ACS(n) __REG32(EMIFS_ACS0 + (4 * (n))) +#define EMIFS_CCS(n) (EMIFS_CS0_CONFIG + (4 * (n))) +#define EMIFS_ACS(n) (EMIFS_ACS0 + (4 * (n))) /* Almost all documentation for chip and board memory maps assumes * BM is clear. Most devel boards have a switch to control booting @@ -93,13 +91,13 @@ */ static inline u32 omap_cs0_phys(void) { - return (OMAP_EMIFS_CONFIG_REG & OMAP_EMIFS_CONFIG_BM) + return (omap_readl(EMIFS_CONFIG) & OMAP_EMIFS_CONFIG_BM) ? OMAP_CS3_PHYS : 0; } static inline u32 omap_cs3_phys(void) { - return (OMAP_EMIFS_CONFIG_REG & OMAP_EMIFS_CONFIG_BM) + return (omap_readl(EMIFS_CONFIG) & OMAP_EMIFS_CONFIG_BM) ? 0 : OMAP_CS3_PHYS; } diff --git a/include/asm-arm/arch-omap/usb.h b/include/asm-arm/arch-omap/usb.h index 2147d18aaea..ddf1861e6df 100644 --- a/include/asm-arm/arch-omap/usb.h +++ b/include/asm-arm/arch-omap/usb.h @@ -34,11 +34,8 @@ /* * OTG and transceiver registers, for OMAPs starting with ARM926 */ -#define OTG_REG32(offset) __REG32(OTG_BASE + (offset)) -#define OTG_REG16(offset) __REG16(OTG_BASE + (offset)) - -#define OTG_REV_REG OTG_REG32(0x00) -#define OTG_SYSCON_1_REG OTG_REG32(0x04) +#define OTG_REV (OTG_BASE + 0x00) +#define OTG_SYSCON_1 (OTG_BASE + 0x04) # define USB2_TRX_MODE(w) (((w)>>24)&0x07) # define USB1_TRX_MODE(w) (((w)>>20)&0x07) # define USB0_TRX_MODE(w) (((w)>>16)&0x07) @@ -47,7 +44,7 @@ # define DEV_IDLE_EN (1 << 13) # define OTG_RESET_DONE (1 << 2) # define OTG_SOFT_RESET (1 << 1) -#define OTG_SYSCON_2_REG OTG_REG32(0x08) +#define OTG_SYSCON_2 (OTG_BASE + 0x08) # define OTG_EN (1 << 31) # define USBX_SYNCHRO (1 << 30) # define OTG_MST16 (1 << 29) @@ -65,7 +62,7 @@ # define HMC_TLLSPEED (1 << 7) # define HMC_TLLATTACH (1 << 6) # define OTG_HMC(w) (((w)>>0)&0x3f) -#define OTG_CTRL_REG OTG_REG32(0x0c) +#define OTG_CTRL (OTG_BASE + 0x0c) # define OTG_USB2_EN (1 << 29) # define OTG_USB2_DP (1 << 28) # define OTG_USB2_DM (1 << 27) @@ -92,7 +89,7 @@ # define OTG_PD_VBUS (1 << 2) # define OTG_PU_VBUS (1 << 1) # define OTG_PU_ID (1 << 0) -#define OTG_IRQ_EN_REG OTG_REG16(0x10) +#define OTG_IRQ_EN (OTG_BASE + 0x10) /* 16-bit */ # define DRIVER_SWITCH (1 << 15) # define A_VBUS_ERR (1 << 13) # define A_REQ_TMROUT (1 << 12) @@ -102,9 +99,9 @@ # define B_SRP_DONE (1 << 8) # define B_SRP_STARTED (1 << 7) # define OPRT_CHG (1 << 0) -#define OTG_IRQ_SRC_REG OTG_REG16(0x14) +#define OTG_IRQ_SRC (OTG_BASE + 0x14) /* 16-bit */ // same bits as in IRQ_EN -#define OTG_OUTCTRL_REG OTG_REG16(0x18) +#define OTG_OUTCTRL (OTG_BASE + 0x18) /* 16-bit */ # define OTGVPD (1 << 14) # define OTGVPU (1 << 13) # define OTGPUID (1 << 12) @@ -117,13 +114,13 @@ # define USB0VDR (1 << 2) # define USB0PDEN (1 << 1) # define USB0PUEN (1 << 0) -#define OTG_TEST_REG OTG_REG16(0x20) -#define OTG_VENDOR_CODE_REG OTG_REG32(0xfc) +#define OTG_TEST (OTG_BASE + 0x20) /* 16-bit */ +#define OTG_VENDOR_CODE (OTG_BASE + 0xfc) /* 16-bit */ /*-------------------------------------------------------------------------*/ /* OMAP1 */ -#define USB_TRANSCEIVER_CTRL_REG __REG32(0xfffe1000 + 0x0064) +#define USB_TRANSCEIVER_CTRL (0xfffe1000 + 0x0064) # define CONF_USB2_UNI_R (1 << 8) # define CONF_USB1_UNI_R (1 << 7) # define CONF_USB_PORT0_R(x) (((x)>>4)&0x7) diff --git a/include/asm-arm/arch-orion5x/io.h b/include/asm-arm/arch-orion5x/io.h index 50f8c880220..59f1bc96a23 100644 --- a/include/asm-arm/arch-orion5x/io.h +++ b/include/asm-arm/arch-orion5x/io.h @@ -14,7 +14,6 @@ #include "orion5x.h" #define IO_SPACE_LIMIT 0xffffffff -#define IO_SPACE_REMAP ORION5X_PCI_SYS_IO_BASE static inline void __iomem * __arch_ioremap(unsigned long paddr, size_t size, unsigned int mtype) @@ -53,15 +52,12 @@ static inline void __iomem *__io(unsigned long addr) /***************************************************************************** * Helpers to access Orion registers ****************************************************************************/ -#define orion5x_read(r) __raw_readl(r) -#define orion5x_write(r, val) __raw_writel(val, r) - /* * These are not preempt-safe. Locks, if needed, must be taken * care of by the caller. */ -#define orion5x_setbits(r, mask) orion5x_write((r), orion5x_read(r) | (mask)) -#define orion5x_clrbits(r, mask) orion5x_write((r), orion5x_read(r) & ~(mask)) +#define orion5x_setbits(r, mask) writel(readl(r) | (mask), (r)) +#define orion5x_clrbits(r, mask) writel(readl(r) & ~(mask), (r)) #endif diff --git a/include/asm-arm/arch-orion5x/orion5x.h b/include/asm-arm/arch-orion5x/orion5x.h index 206ddd71e19..10257f5c5e9 100644 --- a/include/asm-arm/arch-orion5x/orion5x.h +++ b/include/asm-arm/arch-orion5x/orion5x.h @@ -2,7 +2,7 @@ * include/asm-arm/arch-orion5x/orion5x.h * * Generic definitions of Orion SoC flavors: - * Orion-1, Orion-NAS, Orion-VoIP, and Orion-2. + * Orion-1, Orion-VoIP, Orion-NAS, and Orion-2. * * Maintainer: Tzachi Perelstein <tzachi@marvell.com> * @@ -63,9 +63,11 @@ /******************************************************************************* * Supported Devices & Revisions ******************************************************************************/ -/* Orion-1 (88F5181) */ +/* Orion-1 (88F5181) and Orion-VoIP (88F5181L) */ #define MV88F5181_DEV_ID 0x5181 #define MV88F5181_REV_B1 3 +#define MV88F5181L_REV_A0 8 +#define MV88F5181L_REV_A1 9 /* Orion-NAS (88F5182) */ #define MV88F5182_DEV_ID 0x5182 #define MV88F5182_REV_A2 2 @@ -152,6 +154,7 @@ #define BRIDGE_MASK ORION5X_BRIDGE_REG(0x114) #define BRIDGE_INT_TIMER0 0x0002 #define BRIDGE_INT_TIMER1 0x0004 +#define BRIDGE_INT_TIMER1_CLR (~0x0004) #define MAIN_IRQ_CAUSE ORION5X_BRIDGE_REG(0x200) #define MAIN_IRQ_MASK ORION5X_BRIDGE_REG(0x204) diff --git a/include/asm-arm/arch-orion5x/uncompress.h b/include/asm-arm/arch-orion5x/uncompress.h index 5c13d4fafb4..7548cedf2d7 100644 --- a/include/asm-arm/arch-orion5x/uncompress.h +++ b/include/asm-arm/arch-orion5x/uncompress.h @@ -8,23 +8,38 @@ * warranty of any kind, whether express or implied. */ +#include <linux/serial_reg.h> #include <asm/arch/orion5x.h> -#define MV_UART_THR ((volatile unsigned char *)(UART0_PHYS_BASE + 0x0)) -#define MV_UART_LSR ((volatile unsigned char *)(UART0_PHYS_BASE + 0x14)) - -#define LSR_THRE 0x20 +#define SERIAL_BASE ((unsigned char *)UART0_PHYS_BASE) static void putc(const char c) { - int j = 0x1000; - while (--j && !(*MV_UART_LSR & LSR_THRE)) + unsigned char *base = SERIAL_BASE; + int i; + + for (i = 0; i < 0x1000; i++) { + if (base[UART_LSR << 2] & UART_LSR_THRE) + break; barrier(); - *MV_UART_THR = c; + } + + base[UART_TX << 2] = c; } static void flush(void) { + unsigned char *base = SERIAL_BASE; + unsigned char mask; + int i; + + mask = UART_LSR_TEMT | UART_LSR_THRE; + + for (i = 0; i < 0x1000; i++) { + if ((base[UART_LSR << 2] & mask) == mask) + break; + barrier(); + } } /* diff --git a/include/asm-arm/arch-rpc/io.h b/include/asm-arm/arch-rpc/io.h index b4da08d7a33..6bd2295c0e0 100644 --- a/include/asm-arm/arch-rpc/io.h +++ b/include/asm-arm/arch-rpc/io.h @@ -126,7 +126,7 @@ static inline unsigned sz __in##fnsuffix (unsigned int port) \ return (unsigned sz)value; \ } -static inline void __iomem *__ioaddr(unsigned int port) +static inline void __iomem *__deprecated __ioaddr(unsigned int port) { void __iomem *ret; if (__PORT_PCIO(port)) @@ -232,8 +232,7 @@ DECLARE_IO(int,l,"") result; \ }) -#define __ioaddrc(port) \ - ((__PORT_PCIO(port) ? PCIO_BASE : IO_BASE) + ((port) << 2)) +#define __ioaddrc(port) __ioaddr(port) #define inb(p) (__builtin_constant_p((p)) ? __inbc(p) : __inb(p)) #define inw(p) (__builtin_constant_p((p)) ? __inwc(p) : __inw(p)) diff --git a/include/asm-arm/arch-s3c2410/gpio.h b/include/asm-arm/arch-s3c2410/gpio.h index 7583895fd33..18e10d2c35e 100644 --- a/include/asm-arm/arch-s3c2410/gpio.h +++ b/include/asm-arm/arch-s3c2410/gpio.h @@ -1,68 +1,18 @@ -/* - * linux/include/asm-arm/arch-s3c2410/gpio.h +/* linux/include/asm-arm/arch-s3c2410/gpio.h * - * S3C2410 GPIO wrappers for arch-neutral GPIO calls + * Copyright (c) 2008 Simtec Electronics + * http://armlinux.simtec.co.uk/ + * Ben Dooks <ben@simtec.co.uk> * - * Written by Philipp Zabel <philipp.zabel@gmail.com> + * S3C2410 - GPIO lib support * * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License as published by - * the Free Software Foundation; either version 2 of the License, or - * (at your option) any later version. - * - * This program is distributed in the hope that it will be useful, - * but WITHOUT ANY WARRANTY; without even the implied warranty of - * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the - * GNU General Public License for more details. - * - * You should have received a copy of the GNU General Public License - * along with this program; if not, write to the Free Software - * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA - * - */ - -#ifndef __ASM_ARCH_S3C2410_GPIO_H -#define __ASM_ARCH_S3C2410_GPIO_H - -#include <asm/irq.h> -#include <asm/hardware.h> -#include <asm/arch/regs-gpio.h> - -static inline int gpio_request(unsigned gpio, const char *label) -{ - return 0; -} - -static inline void gpio_free(unsigned gpio) -{ - return; -} - -static inline int gpio_direction_input(unsigned gpio) -{ - s3c2410_gpio_cfgpin(gpio, S3C2410_GPIO_INPUT); - return 0; -} - -static inline int gpio_direction_output(unsigned gpio, int value) -{ - s3c2410_gpio_cfgpin(gpio, S3C2410_GPIO_OUTPUT); - /* REVISIT can we write the value first, to avoid glitching? */ - s3c2410_gpio_setpin(gpio, value); - return 0; -} - -#define gpio_get_value(gpio) s3c2410_gpio_getpin(gpio) -#define gpio_set_value(gpio,value) s3c2410_gpio_setpin(gpio, value) - -#include <asm-generic/gpio.h> /* cansleep wrappers */ - -#ifdef CONFIG_CPU_S3C2400 -#define gpio_to_irq(gpio) s3c2400_gpio_getirq(gpio) -#else -#define gpio_to_irq(gpio) s3c2410_gpio_getirq(gpio) -#endif + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. +*/ -/* FIXME implement irq_to_gpio() */ +#define gpio_get_value __gpio_get_value +#define gpio_set_value __gpio_set_value +#define gpio_cansleep __gpio_cansleep -#endif +#include <asm-generic/gpio.h> diff --git a/include/asm-arm/arch-s3c2410/regs-clock.h b/include/asm-arm/arch-s3c2410/regs-clock.h index ecae9e7f5e4..37661358b42 100644 --- a/include/asm-arm/arch-s3c2410/regs-clock.h +++ b/include/asm-arm/arch-s3c2410/regs-clock.h @@ -189,6 +189,8 @@ s3c2410_get_pll(unsigned int pllval, unsigned int baseclk) #define S3C2412_CLKSRC_I2SCLK_MPLL (1<<9) #define S3C2412_CLKSRC_USBCLK_HCLK (1<<10) #define S3C2412_CLKSRC_CAMCLK_HCLK (1<<11) +#define S3C2412_CLKSRC_UREFCLK_EXTCLK (1<<12) +#define S3C2412_CLKSRC_EREFCLK_EXTCLK (1<<14) #endif /* CONFIG_CPU_S3C2412 | CONFIG_CPU_S3C2413 */ diff --git a/include/asm-arm/assembler.h b/include/asm-arm/assembler.h index fce83282082..911393b2c6f 100644 --- a/include/asm-arm/assembler.h +++ b/include/asm-arm/assembler.h @@ -56,6 +56,21 @@ #endif /* + * This can be used to enable code to cacheline align the destination + * pointer when bulk writing to memory. Experiments on StrongARM and + * XScale didn't show this a worthwhile thing to do when the cache is not + * set to write-allocate (this would need further testing on XScale when WA + * is used). + * + * On Feroceon there is much to gain however, regardless of cache mode. + */ +#ifdef CONFIG_CPU_FEROCEON +#define CALGN(code...) code +#else +#define CALGN(code...) +#endif + +/* * Enable and disable interrupts */ #if __LINUX_ARM_ARCH__ >= 6 diff --git a/include/asm-arm/cacheflush.h b/include/asm-arm/cacheflush.h index 759a97b56ee..70b0fe724b6 100644 --- a/include/asm-arm/cacheflush.h +++ b/include/asm-arm/cacheflush.h @@ -95,11 +95,7 @@ #endif #if defined(CONFIG_CPU_FEROCEON) -# ifdef _CACHE -# define MULTI_CACHE 1 -# else -# define _CACHE feroceon -# endif +# define MULTI_CACHE 1 #endif #if defined(CONFIG_CPU_V6) @@ -410,6 +406,13 @@ extern void flush_dcache_page(struct page *); extern void __flush_dcache_page(struct address_space *mapping, struct page *page); +static inline void __flush_icache_all(void) +{ + asm("mcr p15, 0, %0, c7, c5, 0 @ invalidate I-cache\n" + : + : "r" (0)); +} + #define ARCH_HAS_FLUSH_ANON_PAGE static inline void flush_anon_page(struct vm_area_struct *vma, struct page *page, unsigned long vmaddr) diff --git a/include/asm-arm/dyntick.h b/include/asm-arm/dyntick.h deleted file mode 100644 index 19fab2d2b76..00000000000 --- a/include/asm-arm/dyntick.h +++ /dev/null @@ -1,6 +0,0 @@ -#ifndef _ASMARM_DYNTICK_H -#define _ASMARM_DYNTICK_H - -#include <asm/mach/time.h> - -#endif /* _ASMARM_DYNTICK_H */ diff --git a/include/asm-arm/ecard.h b/include/asm-arm/ecard.h index 684fe064523..5e22881a630 100644 --- a/include/asm-arm/ecard.h +++ b/include/asm-arm/ecard.h @@ -85,19 +85,6 @@ #define MAX_ECARDS 9 -typedef enum { /* Cards address space */ - ECARD_IOC, - ECARD_MEMC, - ECARD_EASI -} card_type_t; - -typedef enum { /* Speed for ECARD_IOC space */ - ECARD_SLOW = 0, - ECARD_MEDIUM = 1, - ECARD_FAST = 2, - ECARD_SYNC = 3 -} card_speed_t; - struct ecard_id { /* Card ID structure */ unsigned short manufacturer; unsigned short product; @@ -190,16 +177,6 @@ struct in_chunk_dir { }; /* - * ecard_claim: claim an expansion card entry - */ -#define ecard_claim(ec) ((ec)->claimed = 1) - -/* - * ecard_release: release an expansion card entry - */ -#define ecard_release(ec) ((ec)->claimed = 0) - -/* * Read a chunk from an expansion card * cd : where to put read data * ec : expansion card info struct @@ -209,18 +186,6 @@ struct in_chunk_dir { extern int ecard_readchunk (struct in_chunk_dir *cd, struct expansion_card *ec, int id, int num); /* - * Obtain the address of a card. This returns the "old style" address - * and should no longer be used. - */ -static inline unsigned int __deprecated -ecard_address(struct expansion_card *ec, card_type_t type, card_speed_t speed) -{ - extern unsigned int __ecard_address(struct expansion_card *, - card_type_t, card_speed_t); - return __ecard_address(ec, type, speed); -} - -/* * Request and release ecard resources */ extern int ecard_request_resources(struct expansion_card *ec); diff --git a/include/asm-arm/hardware/iop3xx-gpio.h b/include/asm-arm/hardware/iop3xx-gpio.h new file mode 100644 index 00000000000..0c9331f9ac2 --- /dev/null +++ b/include/asm-arm/hardware/iop3xx-gpio.h @@ -0,0 +1,73 @@ +/* + * linux/include/asm-arm/hardware/iop3xx-gpio.h + * + * IOP3xx GPIO wrappers + * + * Copyright (c) 2008 Arnaud Patard <arnaud.patard@rtp-net.org> + * Based on IXP4XX gpio.h file + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA + * + */ + +#ifndef __ASM_ARM_HARDWARE_IOP3XX_GPIO_H +#define __ASM_ARM_HARDWARE_IOP3XX_GPIO_H + +#include <asm/hardware.h> +#include <asm-generic/gpio.h> + +#define IOP3XX_N_GPIOS 8 + +static inline int gpio_get_value(unsigned gpio) +{ + if (gpio > IOP3XX_N_GPIOS) + return __gpio_get_value(gpio); + + return gpio_line_get(gpio); +} + +static inline void gpio_set_value(unsigned gpio, int value) +{ + if (gpio > IOP3XX_N_GPIOS) { + __gpio_set_value(gpio, value); + return; + } + gpio_line_set(gpio, value); +} + +static inline int gpio_cansleep(unsigned gpio) +{ + if (gpio < IOP3XX_N_GPIOS) + return 0; + else + return __gpio_cansleep(gpio); +} + +/* + * The GPIOs are not generating any interrupt + * Note : manuals are not clear about this + */ +static inline int gpio_to_irq(int gpio) +{ + return -EINVAL; +} + +static inline int irq_to_gpio(int gpio) +{ + return -EINVAL; +} + +#endif + diff --git a/include/asm-arm/hw_irq.h b/include/asm-arm/hw_irq.h index 98d594a973d..f1a08a50060 100644 --- a/include/asm-arm/hw_irq.h +++ b/include/asm-arm/hw_irq.h @@ -6,15 +6,4 @@ #include <asm/mach/irq.h> -#if defined(CONFIG_NO_IDLE_HZ) -# include <asm/dyntick.h> -# define handle_dynamic_tick(action) \ - if (!(action->flags & IRQF_TIMER) && system_timer->dyn_tick) { \ - write_seqlock(&xtime_lock); \ - if (system_timer->dyn_tick->state & DYN_TICK_ENABLED) \ - system_timer->dyn_tick->handler(irq, NULL); \ - write_sequnlock(&xtime_lock); \ - } -#endif - #endif diff --git a/include/asm-arm/kexec.h b/include/asm-arm/kexec.h index 47fe34d692d..c8986bb99ed 100644 --- a/include/asm-arm/kexec.h +++ b/include/asm-arm/kexec.h @@ -14,8 +14,6 @@ #define KEXEC_ARCH KEXEC_ARCH_ARM -#define KEXEC_BOOT_PARAMS_SIZE 1536 - #define KEXEC_ARM_ATAGS_OFFSET 0x1000 #define KEXEC_ARM_ZIMAGE_OFFSET 0x8000 diff --git a/include/asm-arm/mach/time.h b/include/asm-arm/mach/time.h index 5dc357013b7..2fd36ea0130 100644 --- a/include/asm-arm/mach/time.h +++ b/include/asm-arm/mach/time.h @@ -41,30 +41,8 @@ struct sys_timer { #ifndef CONFIG_GENERIC_TIME unsigned long (*offset)(void); #endif - -#ifdef CONFIG_NO_IDLE_HZ - struct dyn_tick_timer *dyn_tick; -#endif -}; - -#ifdef CONFIG_NO_IDLE_HZ - -#define DYN_TICK_ENABLED (1 << 1) - -struct dyn_tick_timer { - spinlock_t lock; - unsigned int state; /* Current state */ - int (*enable)(void); /* Enables dynamic tick */ - int (*disable)(void); /* Disables dynamic tick */ - void (*reprogram)(unsigned long); /* Reprograms the timer */ - int (*handler)(int, void *); }; -void timer_dyn_reprogram(void); -#else -#define timer_dyn_reprogram() do { } while (0) -#endif - extern struct sys_timer *system_timer; extern void timer_tick(void); diff --git a/include/asm-arm/mmu_context.h b/include/asm-arm/mmu_context.h index 6913d02ca5d..91b9dfdfed5 100644 --- a/include/asm-arm/mmu_context.h +++ b/include/asm-arm/mmu_context.h @@ -97,6 +97,11 @@ switch_mm(struct mm_struct *prev, struct mm_struct *next, #ifdef CONFIG_MMU unsigned int cpu = smp_processor_id(); +#ifdef CONFIG_SMP + /* check for possible thread migration */ + if (!cpus_empty(next->cpu_vm_mask) && !cpu_isset(cpu, next->cpu_vm_mask)) + __flush_icache_all(); +#endif if (!cpu_test_and_set(cpu, next->cpu_vm_mask) || prev != next) { check_context(next); cpu_switch_mm(next->pgd, next); diff --git a/include/asm-arm/plat-orion/cache-feroceon-l2.h b/include/asm-arm/plat-orion/cache-feroceon-l2.h new file mode 100644 index 00000000000..ba4e016d3ec --- /dev/null +++ b/include/asm-arm/plat-orion/cache-feroceon-l2.h @@ -0,0 +1,11 @@ +/* + * include/asm-arm/plat-orion/cache-feroceon-l2.h + * + * Copyright (C) 2008 Marvell Semiconductor + * + * This file is licensed under the terms of the GNU General Public + * License version 2. This program is licensed "as is" without any + * warranty of any kind, whether express or implied. + */ + +extern void __init feroceon_l2_init(int l2_wt_override); diff --git a/include/asm-arm/plat-orion/orion_nand.h b/include/asm-arm/plat-orion/orion_nand.h index ffd3852a0dd..ad4ce94c199 100644 --- a/include/asm-arm/plat-orion/orion_nand.h +++ b/include/asm-arm/plat-orion/orion_nand.h @@ -18,6 +18,7 @@ struct orion_nand_data { u8 ale; /* address line number connected to ALE */ u8 cle; /* address line number connected to CLE */ u8 width; /* buswidth */ + u8 chip_delay; }; diff --git a/include/asm-arm/plat-orion/pcie.h b/include/asm-arm/plat-orion/pcie.h index 6434ac685d2..e61b7bd97af 100644 --- a/include/asm-arm/plat-orion/pcie.h +++ b/include/asm-arm/plat-orion/pcie.h @@ -14,6 +14,7 @@ u32 orion_pcie_dev_id(void __iomem *base); u32 orion_pcie_rev(void __iomem *base); int orion_pcie_link_up(void __iomem *base); +int orion_pcie_x4_mode(void __iomem *base); int orion_pcie_get_local_bus_nr(void __iomem *base); void orion_pcie_set_local_bus_nr(void __iomem *base, int nr); void orion_pcie_setup(void __iomem *base, diff --git a/include/asm-arm/plat-s3c/regs-timer.h b/include/asm-arm/plat-s3c/regs-timer.h index 8b0d594397b..b5bc692f348 100644 --- a/include/asm-arm/plat-s3c/regs-timer.h +++ b/include/asm-arm/plat-s3c/regs-timer.h @@ -65,6 +65,15 @@ #define S3C2410_TCFG1_MUX0_TCLK0 (4<<0) #define S3C2410_TCFG1_MUX0_MASK (15<<0) +#define S3C2410_TCFG1_MUX_DIV2 (0<<0) +#define S3C2410_TCFG1_MUX_DIV4 (1<<0) +#define S3C2410_TCFG1_MUX_DIV8 (2<<0) +#define S3C2410_TCFG1_MUX_DIV16 (3<<0) +#define S3C2410_TCFG1_MUX_TCLK (4<<0) +#define S3C2410_TCFG1_MUX_MASK (15<<0) + +#define S3C2410_TCFG1_SHIFT(x) ((x) * 4) + /* for each timer, we have an count buffer, an compare buffer and * an observation buffer */ diff --git a/include/asm-arm/plat-s3c24xx/devs.h b/include/asm-arm/plat-s3c24xx/devs.h index f9d6f0317bc..badaac9d64a 100644 --- a/include/asm-arm/plat-s3c24xx/devs.h +++ b/include/asm-arm/plat-s3c24xx/devs.h @@ -21,6 +21,8 @@ extern struct s3c24xx_uart_resources s3c2410_uart_resources[]; extern struct platform_device *s3c24xx_uart_devs[]; extern struct platform_device *s3c24xx_uart_src[]; +extern struct platform_device s3c_device_timer[]; + extern struct platform_device s3c_device_usb; extern struct platform_device s3c_device_lcd; extern struct platform_device s3c_device_wdt; @@ -36,11 +38,6 @@ extern struct platform_device s3c_device_spi1; extern struct platform_device s3c_device_nand; -extern struct platform_device s3c_device_timer0; -extern struct platform_device s3c_device_timer1; -extern struct platform_device s3c_device_timer2; -extern struct platform_device s3c_device_timer3; - extern struct platform_device s3c_device_usbgadget; /* s3c2440 specific devices */ diff --git a/include/asm-arm/rtc.h b/include/asm-arm/rtc.h deleted file mode 100644 index 1a5c9232a91..00000000000 --- a/include/asm-arm/rtc.h +++ /dev/null @@ -1,43 +0,0 @@ -/* - * linux/include/asm-arm/rtc.h - * - * Copyright (C) 2003 Deep Blue Solutions Ltd. - * - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License version 2 as - * published by the Free Software Foundation. - */ -#ifndef ASMARM_RTC_H -#define ASMARM_RTC_H - -struct module; - -struct rtc_ops { - struct module *owner; - int (*open)(void); - void (*release)(void); - int (*ioctl)(unsigned int, unsigned long); - - int (*read_time)(struct rtc_time *); - int (*set_time)(struct rtc_time *); - int (*read_alarm)(struct rtc_wkalrm *); - int (*set_alarm)(struct rtc_wkalrm *); - int (*proc)(char *buf); -}; - -void rtc_next_alarm_time(struct rtc_time *, struct rtc_time *, struct rtc_time *); -void rtc_update(unsigned long, unsigned long); -int register_rtc(struct rtc_ops *); -void unregister_rtc(struct rtc_ops *); - -static inline int rtc_periodic_alarm(struct rtc_time *tm) -{ - return (tm->tm_year == -1) || - ((unsigned)tm->tm_mon >= 12) || - ((unsigned)(tm->tm_mday - 1) >= 31) || - ((unsigned)tm->tm_hour > 23) || - ((unsigned)tm->tm_min > 59) || - ((unsigned)tm->tm_sec > 59); -} - -#endif diff --git a/include/asm-arm/tlbflush.h b/include/asm-arm/tlbflush.h index 8c6bc1bb9d1..909656c747e 100644 --- a/include/asm-arm/tlbflush.h +++ b/include/asm-arm/tlbflush.h @@ -39,6 +39,7 @@ #define TLB_V6_D_ASID (1 << 17) #define TLB_V6_I_ASID (1 << 18) +#define TLB_L2CLEAN_FR (1 << 29) /* Feroceon */ #define TLB_DCLEAN (1 << 30) #define TLB_WB (1 << 31) @@ -51,6 +52,7 @@ * v4 - ARMv4 without write buffer * v4wb - ARMv4 with write buffer without I TLB flush entry instruction * v4wbi - ARMv4 with write buffer with I TLB flush entry instruction + * fr - Feroceon (v4wbi with non-outer-cacheable page table walks) * v6wbi - ARMv6 with write buffer with I TLB flush entry instruction */ #undef _TLB @@ -103,6 +105,23 @@ # define v4wbi_always_flags (-1UL) #endif +#define fr_tlb_flags (TLB_WB | TLB_DCLEAN | TLB_L2CLEAN_FR | \ + TLB_V4_I_FULL | TLB_V4_D_FULL | \ + TLB_V4_I_PAGE | TLB_V4_D_PAGE) + +#ifdef CONFIG_CPU_TLB_FEROCEON +# define fr_possible_flags fr_tlb_flags +# define fr_always_flags fr_tlb_flags +# ifdef _TLB +# define MULTI_TLB 1 +# else +# define _TLB v4wbi +# endif +#else +# define fr_possible_flags 0 +# define fr_always_flags (-1UL) +#endif + #define v4wb_tlb_flags (TLB_WB | TLB_DCLEAN | \ TLB_V4_I_FULL | TLB_V4_D_FULL | \ TLB_V4_D_PAGE) @@ -245,12 +264,14 @@ extern struct cpu_tlb_fns cpu_tlb; #define possible_tlb_flags (v3_possible_flags | \ v4_possible_flags | \ v4wbi_possible_flags | \ + fr_possible_flags | \ v4wb_possible_flags | \ v6wbi_possible_flags) #define always_tlb_flags (v3_always_flags & \ v4_always_flags & \ v4wbi_always_flags & \ + fr_always_flags & \ v4wb_always_flags & \ v6wbi_always_flags) @@ -417,6 +438,11 @@ static inline void flush_pmd_entry(pmd_t *pmd) if (tlb_flag(TLB_DCLEAN)) asm("mcr p15, 0, %0, c7, c10, 1 @ flush_pmd" : : "r" (pmd) : "cc"); + + if (tlb_flag(TLB_L2CLEAN_FR)) + asm("mcr p15, 1, %0, c15, c9, 1 @ L2 flush_pmd" + : : "r" (pmd) : "cc"); + if (tlb_flag(TLB_WB)) dsb(); } @@ -428,6 +454,10 @@ static inline void clean_pmd_entry(pmd_t *pmd) if (tlb_flag(TLB_DCLEAN)) asm("mcr p15, 0, %0, c7, c10, 1 @ flush_pmd" : : "r" (pmd) : "cc"); + + if (tlb_flag(TLB_L2CLEAN_FR)) + asm("mcr p15, 1, %0, c15, c9, 1 @ L2 flush_pmd" + : : "r" (pmd) : "cc"); } #undef tlb_flag diff --git a/kernel/hrtimer.c b/kernel/hrtimer.c index ab80515008f..3c00794bc88 100644 --- a/kernel/hrtimer.c +++ b/kernel/hrtimer.c @@ -1086,7 +1086,7 @@ ktime_t hrtimer_get_remaining(const struct hrtimer *timer) } EXPORT_SYMBOL_GPL(hrtimer_get_remaining); -#if defined(CONFIG_NO_IDLE_HZ) || defined(CONFIG_NO_HZ) +#ifdef CONFIG_NO_HZ /** * hrtimer_get_next_event - get the time until next expiry event * diff --git a/kernel/sysctl.c b/kernel/sysctl.c index 29116652dca..f6d2e57b99a 100644 --- a/kernel/sysctl.c +++ b/kernel/sysctl.c @@ -132,8 +132,6 @@ extern int sysctl_userprocess_debug; extern int spin_retry; #endif -extern int sysctl_hz_timer; - #ifdef CONFIG_BSD_PROCESS_ACCT extern int acct_parm[]; #endif @@ -563,16 +561,6 @@ static struct ctl_table kern_table[] = { .proc_handler = &proc_dointvec, }, #endif -#ifdef CONFIG_NO_IDLE_HZ - { - .ctl_name = KERN_HZ_TIMER, - .procname = "hz_timer", - .data = &sysctl_hz_timer, - .maxlen = sizeof(int), - .mode = 0644, - .proc_handler = &proc_dointvec, - }, -#endif { .ctl_name = KERN_S390_USER_DEBUG_LOGGING, .procname = "userprocess_debug", diff --git a/kernel/timer.c b/kernel/timer.c index ceacc662657..ef3fa6906e8 100644 --- a/kernel/timer.c +++ b/kernel/timer.c @@ -812,7 +812,7 @@ static inline void __run_timers(struct tvec_base *base) spin_unlock_irq(&base->lock); } -#if defined(CONFIG_NO_IDLE_HZ) || defined(CONFIG_NO_HZ) +#ifdef CONFIG_NO_HZ /* * Find out when the next timer event is due to happen. This * is used on S/390 to stop all activity when a cpus is idle. @@ -947,14 +947,6 @@ unsigned long get_next_timer_interrupt(unsigned long now) return cmp_next_hrtimer_event(now, expires); } - -#ifdef CONFIG_NO_IDLE_HZ -unsigned long next_timer_interrupt(void) -{ - return get_next_timer_interrupt(jiffies); -} -#endif - #endif #ifndef CONFIG_VIRT_CPU_ACCOUNTING diff --git a/sound/soc/at91/at91-ssc.c b/sound/soc/at91/at91-ssc.c index bc35d00a38f..1a426095014 100644 --- a/sound/soc/at91/at91-ssc.c +++ b/sound/soc/at91/at91-ssc.c @@ -41,7 +41,7 @@ #define DBG(x...) #endif -#if defined(CONFIG_ARCH_AT91SAM9260) +#if defined(CONFIG_ARCH_AT91SAM9260) || defined(CONFIG_ARCH_AT91SAM9G20) #define NUM_SSC_DEVICES 1 #else #define NUM_SSC_DEVICES 3 |