diff options
| -rw-r--r-- | arch/mips/Kconfig | 3 | ||||
| -rw-r--r-- | drivers/serial/8250.c | 92 | ||||
| -rw-r--r-- | drivers/serial/Kconfig | 9 | ||||
| -rw-r--r-- | include/linux/serial_core.h | 4 |
4 files changed, 95 insertions, 13 deletions
diff --git a/arch/mips/Kconfig b/arch/mips/Kconfig index 130d825e543..7441a2cf523 100644 --- a/arch/mips/Kconfig +++ b/arch/mips/Kconfig @@ -1042,6 +1042,9 @@ config SOC_AU1X00 select SYS_SUPPORTS_APM_EMULATION select SYS_SUPPORTS_KGDB +config SERIAL_RM9000 + bool + config PNX8550 bool select SOC_PNX8550 diff --git a/drivers/serial/8250.c b/drivers/serial/8250.c index 194362d9f5a..c9832d963f1 100644 --- a/drivers/serial/8250.c +++ b/drivers/serial/8250.c @@ -251,9 +251,16 @@ static const struct serial8250_config uart_config[] = { .fcr = UART_FCR_ENABLE_FIFO | UART_FCR_R_TRIG_10, .flags = UART_CAP_FIFO | UART_CAP_UUE, }, + [PORT_RM9000] = { + .name = "RM9000", + .fifo_size = 16, + .tx_loadsz = 16, + .fcr = UART_FCR_ENABLE_FIFO | UART_FCR_R_TRIG_10, + .flags = UART_CAP_FIFO, + }, }; -#ifdef CONFIG_SERIAL_8250_AU1X00 +#if defined (CONFIG_SERIAL_8250_AU1X00) /* Au1x00 UART hardware has a weird register layout */ static const u8 au_io_in_map[] = { @@ -289,6 +296,44 @@ static inline int map_8250_out_reg(struct uart_8250_port *up, int offset) return au_io_out_map[offset]; } +#elif defined (CONFIG_SERIAL_8250_RM9K) + +static const u8 + regmap_in[8] = { + [UART_RX] = 0x00, + [UART_IER] = 0x0c, + [UART_IIR] = 0x14, + [UART_LCR] = 0x1c, + [UART_MCR] = 0x20, + [UART_LSR] = 0x24, + [UART_MSR] = 0x28, + [UART_SCR] = 0x2c + }, + regmap_out[8] = { + [UART_TX] = 0x04, + [UART_IER] = 0x0c, + [UART_FCR] = 0x18, + [UART_LCR] = 0x1c, + [UART_MCR] = 0x20, + [UART_LSR] = 0x24, + [UART_MSR] = 0x28, + [UART_SCR] = 0x2c + }; + +static inline int map_8250_in_reg(struct uart_8250_port *up, int offset) +{ + if (up->port.iotype != UPIO_RM9000) + return offset; + return regmap_in[offset]; +} + +static inline int map_8250_out_reg(struct uart_8250_port *up, int offset) +{ + if (up->port.iotype != UPIO_RM9000) + return offset; + return regmap_out[offset]; +} + #else /* sane hardware needs no mapping */ @@ -311,6 +356,7 @@ static unsigned int serial_in(struct uart_8250_port *up, int offset) case UPIO_DWAPB: return readb(up->port.membase + offset); + case UPIO_RM9000: case UPIO_MEM32: return readl(up->port.membase + offset); @@ -348,6 +394,7 @@ serial_out(struct uart_8250_port *up, int offset, int value) writeb(value, up->port.membase + offset); break; + case UPIO_RM9000: case UPIO_MEM32: writel(value, up->port.membase + offset); break; @@ -419,7 +466,7 @@ static inline void _serial_dl_write(struct uart_8250_port *up, int value) serial_outp(up, UART_DLM, value >> 8 & 0xff); } -#ifdef CONFIG_SERIAL_8250_AU1X00 +#if defined (CONFIG_SERIAL_8250_AU1X00) /* Au1x00 haven't got a standard divisor latch */ static int serial_dl_read(struct uart_8250_port *up) { @@ -436,6 +483,24 @@ static void serial_dl_write(struct uart_8250_port *up, int value) else _serial_dl_write(up, value); } +#elif defined (CONFIG_SERIAL_8250_RM9K) +static int serial_dl_read(struct uart_8250_port *up) +{ + return (up->port.iotype == UPIO_RM9000) ? + (((__raw_readl(up->port.membase + 0x10) << 8) | + (__raw_readl(up->port.membase + 0x08) & 0xff)) & 0xffff) : + _serial_dl_read(up); +} + +static void serial_dl_write(struct uart_8250_port *up, int value) +{ + if (up->port.iotype == UPIO_RM9000) { + __raw_writel(value, up->port.membase + 0x08); + __raw_writel(value >> 8, up->port.membase + 0x10); + } else { + _serial_dl_write(up, value); + } +} #else #define serial_dl_read(up) _serial_dl_read(up) #define serial_dl_write(up, value) _serial_dl_write(up, value) @@ -637,7 +702,7 @@ static unsigned int autoconfig_read_divisor_id(struct uart_8250_port *p) * its clones. (We treat the broken original StarTech 16650 V1 as a * 16550, and why not? Startech doesn't seem to even acknowledge its * existence.) - * + * * What evil have men's minds wrought... */ static void autoconfig_has_efr(struct uart_8250_port *up) @@ -690,7 +755,7 @@ static void autoconfig_has_efr(struct uart_8250_port *up) up->bugs |= UART_BUG_QUOT; return; } - + /* * We check for a XR16C850 by setting DLL and DLM to 0, and then * reading back DLL and DLM. The chip type depends on the DLM @@ -833,7 +898,7 @@ static void autoconfig_16550a(struct uart_8250_port *up) status1 &= ~0xB0; /* Disable LOCK, mask out PRESL[01] */ status1 |= 0x10; /* 1.625 divisor for baud_base --> 921600 */ serial_outp(up, 0x04, status1); - + serial_dl_write(up, quot); serial_outp(up, UART_LCR, 0); @@ -938,7 +1003,7 @@ static void autoconfig(struct uart_8250_port *up, unsigned int probeflags) /* * Do a simple existence test first; if we fail this, * there's no point trying anything else. - * + * * 0x80 is used as a nonsense port to prevent against * false positives due to ISA bus float. The * assumption is that 0x80 is a non-existent port; @@ -977,7 +1042,7 @@ static void autoconfig(struct uart_8250_port *up, unsigned int probeflags) save_mcr = serial_in(up, UART_MCR); save_lcr = serial_in(up, UART_LCR); - /* + /* * Check to see if a UART is really there. Certain broken * internal modems based on the Rockwell chipset fail this * test, because they apparently don't implement the loopback @@ -1084,7 +1149,7 @@ static void autoconfig(struct uart_8250_port *up, unsigned int probeflags) else serial_outp(up, UART_IER, 0); - out: + out: spin_unlock_irqrestore(&up->port.lock, flags); // restore_flags(flags); DEBUG_AUTOCONF("type=%s\n", uart_config[up->port.type].name); @@ -1110,7 +1175,7 @@ static void autoconfig_irq(struct uart_8250_port *up) save_mcr = serial_inp(up, UART_MCR); save_ier = serial_inp(up, UART_IER); serial_outp(up, UART_MCR, UART_MCR_OUT1 | UART_MCR_OUT2); - + irqs = probe_irq_on(); serial_outp(up, UART_MCR, 0); udelay (10); @@ -1175,8 +1240,11 @@ static void serial8250_start_tx(struct uart_port *port) if (up->bugs & UART_BUG_TXEN) { unsigned char lsr, iir; lsr = serial_in(up, UART_LSR); - iir = serial_in(up, UART_IIR); - if (lsr & UART_LSR_TEMT && iir & UART_IIR_NO_INT) + iir = serial_in(up, UART_IIR) & 0x0f; + if ((up->port.type == PORT_RM9000) ? + (lsr & UART_LSR_THRE && + (iir == UART_IIR_NO_INT || iir == UART_IIR_THRI)) : + (lsr & UART_LSR_TEMT && iir & UART_IIR_NO_INT)) transmit_chars(up); } } @@ -1957,7 +2025,7 @@ serial8250_set_termios(struct uart_port *port, struct ktermios *termios, /* * Ask the core to calculate the divisor for us. */ - baud = uart_get_baud_rate(port, termios, old, 0, port->uartclk/16); + baud = uart_get_baud_rate(port, termios, old, 0, port->uartclk/16); quot = serial8250_get_divisor(port, baud); /* diff --git a/drivers/serial/Kconfig b/drivers/serial/Kconfig index ad9f321968e..e9d927e3b8e 100644 --- a/drivers/serial/Kconfig +++ b/drivers/serial/Kconfig @@ -254,6 +254,15 @@ config SERIAL_8250_AU1X00 to this option. The driver can handle 1 or 2 serial ports. If unsure, say N. +config SERIAL_8250_RM9K + bool "Support for MIPS RM9xxx integrated serial port" + depends on SERIAL_8250 != n && SERIAL_RM9000 + select SERIAL_8250_SHARE_IRQ + help + Selecting this option will add support for the integrated serial + port hardware found on MIPS RM9122 and similar processors. + If unsure, say N. + comment "Non-8250 serial port support" config SERIAL_AMBA_PL010 diff --git a/include/linux/serial_core.h b/include/linux/serial_core.h index 8b5592e6aca..d242c731491 100644 --- a/include/linux/serial_core.h +++ b/include/linux/serial_core.h @@ -39,7 +39,8 @@ #define PORT_RSA 13 #define PORT_NS16550A 14 #define PORT_XSCALE 15 -#define PORT_MAX_8250 15 /* max port ID */ +#define PORT_RM9000 16 /* PMC-Sierra RM9xxx internal UART */ +#define PORT_MAX_8250 16 /* max port ID */ /* * ARM specific type numbers. These are not currently guaranteed @@ -231,6 +232,7 @@ struct uart_port { #define UPIO_AU (4) /* Au1x00 type IO */ #define UPIO_TSI (5) /* Tsi108/109 type IO */ #define UPIO_DWAPB (6) /* DesignWare APB UART */ +#define UPIO_RM9000 (7) /* RM9000 type IO */ unsigned int read_status_mask; /* driver specific */ unsigned int ignore_status_mask; /* driver specific */ |