aboutsummaryrefslogtreecommitdiff
diff options
context:
space:
mode:
-rw-r--r--include/linux/usb_gadget.h62
1 files changed, 31 insertions, 31 deletions
diff --git a/include/linux/usb_gadget.h b/include/linux/usb_gadget.h
index 4f59b2aa8a9..ec9732e7fea 100644
--- a/include/linux/usb_gadget.h
+++ b/include/linux/usb_gadget.h
@@ -22,10 +22,10 @@ struct usb_ep;
/**
* struct usb_request - describes one i/o request
* @buf: Buffer used for data. Always provide this; some controllers
- * only use PIO, or don't use DMA for some endpoints.
+ * only use PIO, or don't use DMA for some endpoints.
* @dma: DMA address corresponding to 'buf'. If you don't set this
- * field, and the usb controller needs one, it is responsible
- * for mapping and unmapping the buffer.
+ * field, and the usb controller needs one, it is responsible
+ * for mapping and unmapping the buffer.
* @length: Length of that data
* @no_interrupt: If true, hints that no completion irq is needed.
* Helpful sometimes with deep request queues that are handled
@@ -45,16 +45,16 @@ struct usb_ep;
* @context: For use by the completion callback
* @list: For use by the gadget driver.
* @status: Reports completion code, zero or a negative errno.
- * Normally, faults block the transfer queue from advancing until
- * the completion callback returns.
- * Code "-ESHUTDOWN" indicates completion caused by device disconnect,
- * or when the driver disabled the endpoint.
+ * Normally, faults block the transfer queue from advancing until
+ * the completion callback returns.
+ * Code "-ESHUTDOWN" indicates completion caused by device disconnect,
+ * or when the driver disabled the endpoint.
* @actual: Reports bytes transferred to/from the buffer. For reads (OUT
- * transfers) this may be less than the requested length. If the
- * short_not_ok flag is set, short reads are treated as errors
- * even when status otherwise indicates successful completion.
- * Note that for writes (IN transfers) some data bytes may still
- * reside in a device-side FIFO when the request is reported as
+ * transfers) this may be less than the requested length. If the
+ * short_not_ok flag is set, short reads are treated as errors
+ * even when status otherwise indicates successful completion.
+ * Note that for writes (IN transfers) some data bytes may still
+ * reside in a device-side FIFO when the request is reported as
* complete.
*
* These are allocated/freed through the endpoint they're used with. The
@@ -128,7 +128,7 @@ struct usb_ep_ops {
* value can sometimes be reduced (hardware allowing), according to
* the endpoint descriptor used to configure the endpoint.
* @driver_data:for use by the gadget driver. all other fields are
- * read-only to gadget drivers.
+ * read-only to gadget drivers.
*
* the bus controller driver lists all the general purpose endpoints in
* gadget->ep_list. the control endpoint (gadget->ep0) is not in that list,
@@ -148,10 +148,10 @@ struct usb_ep {
/**
* usb_ep_enable - configure endpoint, making it usable
* @ep:the endpoint being configured. may not be the endpoint named "ep0".
- * drivers discover endpoints through the ep_list of a usb_gadget.
+ * drivers discover endpoints through the ep_list of a usb_gadget.
* @desc:descriptor for desired behavior. caller guarantees this pointer
- * remains valid until the endpoint is disabled; the data byte order
- * is little-endian (usb-standard).
+ * remains valid until the endpoint is disabled; the data byte order
+ * is little-endian (usb-standard).
*
* when configurations are set, or when interface settings change, the driver
* will enable or disable the relevant endpoints. while it is enabled, an
@@ -232,7 +232,7 @@ usb_ep_free_request (struct usb_ep *ep, struct usb_request *req)
* @ep:the endpoint associated with the request
* @req:the request being submitted
* @gfp_flags: GFP_* flags to use in case the lower level driver couldn't
- * pre-allocate all necessary memory with the request.
+ * pre-allocate all necessary memory with the request.
*
* This tells the device controller to perform the specified request through
* that endpoint (reading or writing a buffer). When the request completes,
@@ -415,7 +415,7 @@ struct usb_gadget_ops {
* struct usb_gadget - represents a usb slave device
* @ops: Function pointers used to access hardware-specific operations.
* @ep0: Endpoint zero, used when reading or writing responses to
- * driver setup() requests
+ * driver setup() requests
* @ep_list: List of other endpoints supported by the device.
* @speed: Speed of current connection to USB host.
* @is_dualspeed: True if the controller supports both high and full speed
@@ -432,7 +432,7 @@ struct usb_gadget_ops {
* @b_hnp_enable: OTG device feature flag, indicating that the A-Host
* enabled HNP support.
* @name: Identifies the controller hardware type. Used in diagnostics
- * and sometimes configuration.
+ * and sometimes configuration.
* @dev: Driver model state for this abstract device.
*
* Gadgets have a mostly-portable "gadget driver" implementing device
@@ -655,23 +655,23 @@ usb_gadget_disconnect (struct usb_gadget *gadget)
* @function: String describing the gadget's function
* @speed: Highest speed the driver handles.
* @bind: Invoked when the driver is bound to a gadget, usually
- * after registering the driver.
- * At that point, ep0 is fully initialized, and ep_list holds
- * the currently-available endpoints.
- * Called in a context that permits sleeping.
+ * after registering the driver.
+ * At that point, ep0 is fully initialized, and ep_list holds
+ * the currently-available endpoints.
+ * Called in a context that permits sleeping.
* @setup: Invoked for ep0 control requests that aren't handled by
- * the hardware level driver. Most calls must be handled by
- * the gadget driver, including descriptor and configuration
- * management. The 16 bit members of the setup data are in
- * USB byte order. Called in_interrupt; this may not sleep. Driver
+ * the hardware level driver. Most calls must be handled by
+ * the gadget driver, including descriptor and configuration
+ * management. The 16 bit members of the setup data are in
+ * USB byte order. Called in_interrupt; this may not sleep. Driver
* queues a response to ep0, or returns negative to stall.
* @disconnect: Invoked after all transfers have been stopped,
- * when the host is disconnected. May be called in_interrupt; this
- * may not sleep. Some devices can't detect disconnect, so this might
+ * when the host is disconnected. May be called in_interrupt; this
+ * may not sleep. Some devices can't detect disconnect, so this might
* not be called except as part of controller shutdown.
* @unbind: Invoked when the driver is unbound from a gadget,
- * usually from rmmod (after a disconnect is reported).
- * Called in a context that permits sleeping.
+ * usually from rmmod (after a disconnect is reported).
+ * Called in a context that permits sleeping.
* @suspend: Invoked on USB suspend. May be called in_interrupt.
* @resume: Invoked on USB resume. May be called in_interrupt.
* @driver: Driver model state for this driver.