diff options
| -rw-r--r-- | drivers/net/e1000e/82571.c | 2 | ||||
| -rw-r--r-- | drivers/net/e1000e/ich8lan.c | 5 | ||||
| -rw-r--r-- | drivers/net/e1000e/lib.c | 5 | ||||
| -rw-r--r-- | drivers/net/e1000e/phy.c | 14 |
4 files changed, 11 insertions, 15 deletions
diff --git a/drivers/net/e1000e/82571.c b/drivers/net/e1000e/82571.c index 227f3d03ba2..f6f3a2289e0 100644 --- a/drivers/net/e1000e/82571.c +++ b/drivers/net/e1000e/82571.c @@ -1551,7 +1551,7 @@ bool e1000e_get_laa_state_82571(struct e1000_hw *hw) * @hw: pointer to the HW structure * @state: enable/disable locally administered address * - * Enable/Disable the current locally administers address state. + * Enable/Disable the current locally administered address state. **/ void e1000e_set_laa_state_82571(struct e1000_hw *hw, bool state) { diff --git a/drivers/net/e1000e/ich8lan.c b/drivers/net/e1000e/ich8lan.c index fbbc6ddfde8..1ce2bf97fa3 100644 --- a/drivers/net/e1000e/ich8lan.c +++ b/drivers/net/e1000e/ich8lan.c @@ -1747,7 +1747,7 @@ static s32 e1000_flash_cycle_init_ich8lan(struct e1000_hw *hw) if (hsfsts.hsf_status.flcinprog == 0) { /* * There is no cycle running at present, - * so we can start a cycle + * so we can start a cycle. * Begin by setting Flash Cycle Done. */ hsfsts.hsf_status.flcdone = 1; @@ -1755,7 +1755,7 @@ static s32 e1000_flash_cycle_init_ich8lan(struct e1000_hw *hw) ret_val = 0; } else { /* - * otherwise poll for sometime so the current + * Otherwise poll for sometime so the current * cycle has a chance to end before giving up. */ for (i = 0; i < ICH_FLASH_READ_COMMAND_TIMEOUT; i++) { @@ -2645,7 +2645,6 @@ static s32 e1000_reset_hw_ich8lan(struct e1000_hw *hw) ctrl |= E1000_CTRL_PHY_RST; } ret_val = e1000_acquire_swflag_ich8lan(hw); - /* Whether or not the swflag was acquired, we need to reset the part */ e_dbg("Issuing a global reset to ich8lan\n"); ew32(CTRL, (ctrl | E1000_CTRL_RST)); msleep(20); diff --git a/drivers/net/e1000e/lib.c b/drivers/net/e1000e/lib.c index e3976ea668d..a86c17548c1 100644 --- a/drivers/net/e1000e/lib.c +++ b/drivers/net/e1000e/lib.c @@ -1086,7 +1086,6 @@ s32 e1000e_config_fc_after_link_up(struct e1000_hw *hw) * 1 | 1 | 0 | 0 | e1000_fc_none * 1 | 1 | 0 | 1 | e1000_fc_rx_pause * - * * Are both PAUSE bits set to 1? If so, this implies * Symmetric Flow Control is enabled at both ends. The * ASM_DIR bits are irrelevant per the spec. @@ -1124,7 +1123,6 @@ s32 e1000e_config_fc_after_link_up(struct e1000_hw *hw) * PAUSE | ASM_DIR | PAUSE | ASM_DIR | Result *-------|---------|-------|---------|-------------------- * 0 | 1 | 1 | 1 | e1000_fc_tx_pause - * */ else if (!(mii_nway_adv_reg & NWAY_AR_PAUSE) && (mii_nway_adv_reg & NWAY_AR_ASM_DIR) && @@ -1140,7 +1138,6 @@ s32 e1000e_config_fc_after_link_up(struct e1000_hw *hw) * PAUSE | ASM_DIR | PAUSE | ASM_DIR | Result *-------|---------|-------|---------|-------------------- * 1 | 1 | 0 | 1 | e1000_fc_rx_pause - * */ else if ((mii_nway_adv_reg & NWAY_AR_PAUSE) && (mii_nway_adv_reg & NWAY_AR_ASM_DIR) && @@ -2363,7 +2360,7 @@ static s32 e1000_mng_write_cmd_header(struct e1000_hw *hw, } /** - * e1000_mng_host_if_write - Writes to the manageability host interface + * e1000_mng_host_if_write - Write to the manageability host interface * @hw: pointer to the HW structure * @buffer: pointer to the host interface buffer * @length: size of the buffer diff --git a/drivers/net/e1000e/phy.c b/drivers/net/e1000e/phy.c index 140b23b320f..1bc09b240e6 100644 --- a/drivers/net/e1000e/phy.c +++ b/drivers/net/e1000e/phy.c @@ -153,10 +153,10 @@ s32 e1000e_get_phy_id(struct e1000_hw *hw) goto out; /* - * If the PHY ID is still unknown, we may have an 82577i - * without link. We will try again after setting Slow - * MDIC mode. No harm in trying again in this case since - * the PHY ID is unknown at this point anyway + * If the PHY ID is still unknown, we may have an 82577 + * without link. We will try again after setting Slow MDIC + * mode. No harm in trying again in this case since the PHY + * ID is unknown at this point anyway. */ ret_val = phy->ops.acquire(hw); if (ret_val) @@ -1744,7 +1744,7 @@ out: * The automatic gain control (agc) normalizes the amplitude of the * received signal, adjusting for the attenuation produced by the * cable. By reading the AGC registers, which represent the - * combination of course and fine gain value, the value can be put + * combination of coarse and fine gain value, the value can be put * into a lookup table to obtain the approximate cable length * for each channel. **/ @@ -1769,7 +1769,7 @@ s32 e1000e_get_cable_length_igp_2(struct e1000_hw *hw) /* * Getting bits 15:9, which represent the combination of - * course and fine gain values. The result is a number + * coarse and fine gain values. The result is a number * that can be put into the lookup table to obtain the * approximate cable length. */ @@ -2511,7 +2511,7 @@ static s32 e1000_access_phy_wakeup_reg_bm(struct e1000_hw *hw, u32 offset, ret_val = e1000e_read_phy_reg_mdic(hw, BM_WUC_DATA_OPCODE, data); } else { - /* Read the page 800 value using opcode 0x12 */ + /* Write the page 800 value using opcode 0x12 */ ret_val = e1000e_write_phy_reg_mdic(hw, BM_WUC_DATA_OPCODE, *data); } |