diff options
| -rw-r--r-- | drivers/ata/pata_hpt3x3.c | 51 |
1 files changed, 45 insertions, 6 deletions
diff --git a/drivers/ata/pata_hpt3x3.c b/drivers/ata/pata_hpt3x3.c index f11a320337c..1c9016edf87 100644 --- a/drivers/ata/pata_hpt3x3.c +++ b/drivers/ata/pata_hpt3x3.c @@ -23,7 +23,7 @@ #include <linux/libata.h> #define DRV_NAME "pata_hpt3x3" -#define DRV_VERSION "0.5.3" +#define DRV_VERSION "0.6.1" /** * hpt3x3_set_piomode - PIO setup @@ -80,14 +80,48 @@ static void hpt3x3_set_dmamode(struct ata_port *ap, struct ata_device *adev) r2 &= ~(0x11 << dn); /* Clear MWDMA and UDMA bits */ if (adev->dma_mode >= XFER_UDMA_0) - r2 |= (0x10 << dn); /* Ultra mode */ + r2 |= (0x01 << dn); /* Ultra mode */ else - r2 |= (0x01 << dn); /* MWDMA */ + r2 |= (0x10 << dn); /* MWDMA */ pci_write_config_dword(pdev, 0x44, r1); pci_write_config_dword(pdev, 0x48, r2); } -#endif /* CONFIG_PATA_HPT3X3_DMA */ + +/** + * hpt3x3_freeze - DMA workaround + * @ap: port to freeze + * + * When freezing an HPT3x3 we must stop any pending DMA before + * writing to the control register or the chip will hang + */ + +static int hpt3x3_freeze(struct ata_port *ap) +{ + void __iomem *mmio = ap->ioaddr.bmdma_addr; + + iowrite8(ioread8(mmio + ATA_DMA_CMD) & ~ ATA_DMA_START, + mmio + ATA_DMA_CMD); + ata_sff_dma_pause(ap); + ata_sff_freeze(ap); +} + +/** + * hpt3x3_bmdma_setup - DMA workaround + * @qc: Queued command + * + * When issuing BMDMA we must clean up the error/active bits in + * software on this device + */ + +static void hpt3x3_bmdma_setup(struct ata_queued_cmd *qc) +{ + struct ata_port *ap = qc->ap; + u8 r = ioread8(ap->ioaddr.bmdma_addr + ATA_DMA_STATUS); + r |= ATA_DMA_INTR | ATA_DMA_ERR; + iowrite8(r, ap->ioaddr.bmdma_addr + ATA_DMA_STATUS); + return ata_bmdma_setup(qc); +} /** * hpt3x3_atapi_dma - ATAPI DMA check @@ -101,18 +135,23 @@ static int hpt3x3_atapi_dma(struct ata_queued_cmd *qc) return 1; } +#endif /* CONFIG_PATA_HPT3X3_DMA */ + static struct scsi_host_template hpt3x3_sht = { ATA_BMDMA_SHT(DRV_NAME), }; static struct ata_port_operations hpt3x3_port_ops = { .inherits = &ata_bmdma_port_ops, - .check_atapi_dma= hpt3x3_atapi_dma, .cable_detect = ata_cable_40wire, .set_piomode = hpt3x3_set_piomode, #if defined(CONFIG_PATA_HPT3X3_DMA) .set_dmamode = hpt3x3_set_dmamode, + .bmdma_setup = hpt3x3_bmdma_setup, + .check_atapi_dma= hpt3x3_atapi_dma, + .freeze = hpt3x3_freeze, #endif + }; /** @@ -257,4 +296,4 @@ MODULE_DEVICE_TABLE(pci, hpt3x3); MODULE_VERSION(DRV_VERSION); module_init(hpt3x3_init); -module_exit(hpt3x3_exit); +module_exit(hpt3x3_exit);
\ No newline at end of file |