aboutsummaryrefslogtreecommitdiff
diff options
context:
space:
mode:
-rw-r--r--arch/mips/au1000/pb1100/board_setup.c93
1 files changed, 48 insertions, 45 deletions
diff --git a/arch/mips/au1000/pb1100/board_setup.c b/arch/mips/au1000/pb1100/board_setup.c
index 2d1533f116c..6bc1f8e1b60 100644
--- a/arch/mips/au1000/pb1100/board_setup.c
+++ b/arch/mips/au1000/pb1100/board_setup.c
@@ -47,8 +47,7 @@ void board_reset (void)
void __init board_setup(void)
{
- u32 pin_func;
- u32 sys_freqctrl, sys_clksrc;
+ volatile void __iomem * base = (volatile void __iomem *) 0xac000000UL;
// set AUX clock to 12MHz * 8 = 96 MHz
au_writel(8, SYS_AUXPLL);
@@ -56,58 +55,62 @@ void __init board_setup(void)
udelay(100);
#ifdef CONFIG_USB_OHCI
- // configure pins GPIO[14:9] as GPIO
- pin_func = au_readl(SYS_PINFUNC) & (u32)(~0x80);
-
- /* zero and disable FREQ2 */
- sys_freqctrl = au_readl(SYS_FREQCTRL0);
- sys_freqctrl &= ~0xFFF00000;
- au_writel(sys_freqctrl, SYS_FREQCTRL0);
-
- /* zero and disable USBH/USBD/IrDA clock */
- sys_clksrc = au_readl(SYS_CLKSRC);
- sys_clksrc &= ~0x0000001F;
- au_writel(sys_clksrc, SYS_CLKSRC);
-
- sys_freqctrl = au_readl(SYS_FREQCTRL0);
- sys_freqctrl &= ~0xFFF00000;
-
- sys_clksrc = au_readl(SYS_CLKSRC);
- sys_clksrc &= ~0x0000001F;
-
- // FREQ2 = aux/2 = 48 MHz
- sys_freqctrl |= ((0<<22) | (1<<21) | (1<<20));
- au_writel(sys_freqctrl, SYS_FREQCTRL0);
-
- /*
- * Route 48MHz FREQ2 into USBH/USBD/IrDA
- */
- sys_clksrc |= ((4<<2) | (0<<1) | 0 );
- au_writel(sys_clksrc, SYS_CLKSRC);
-
- /* setup the static bus controller */
- au_writel(0x00000002, MEM_STCFG3); /* type = PCMCIA */
- au_writel(0x280E3D07, MEM_STTIME3); /* 250ns cycle time */
- au_writel(0x10000000, MEM_STADDR3); /* any PCMCIA select */
-
- // get USB Functionality pin state (device vs host drive pins)
- pin_func = au_readl(SYS_PINFUNC) & (u32)(~0x8000);
- // 2nd USB port is USB host
- pin_func |= 0x8000;
- au_writel(pin_func, SYS_PINFUNC);
+ {
+ u32 pin_func, sys_freqctrl, sys_clksrc;
+
+ // configure pins GPIO[14:9] as GPIO
+ pin_func = au_readl(SYS_PINFUNC) & (u32)(~0x80);
+
+ /* zero and disable FREQ2 */
+ sys_freqctrl = au_readl(SYS_FREQCTRL0);
+ sys_freqctrl &= ~0xFFF00000;
+ au_writel(sys_freqctrl, SYS_FREQCTRL0);
+
+ /* zero and disable USBH/USBD/IrDA clock */
+ sys_clksrc = au_readl(SYS_CLKSRC);
+ sys_clksrc &= ~0x0000001F;
+ au_writel(sys_clksrc, SYS_CLKSRC);
+
+ sys_freqctrl = au_readl(SYS_FREQCTRL0);
+ sys_freqctrl &= ~0xFFF00000;
+
+ sys_clksrc = au_readl(SYS_CLKSRC);
+ sys_clksrc &= ~0x0000001F;
+
+ // FREQ2 = aux/2 = 48 MHz
+ sys_freqctrl |= ((0<<22) | (1<<21) | (1<<20));
+ au_writel(sys_freqctrl, SYS_FREQCTRL0);
+
+ /*
+ * Route 48MHz FREQ2 into USBH/USBD/IrDA
+ */
+ sys_clksrc |= ((4<<2) | (0<<1) | 0 );
+ au_writel(sys_clksrc, SYS_CLKSRC);
+
+ /* setup the static bus controller */
+ au_writel(0x00000002, MEM_STCFG3); /* type = PCMCIA */
+ au_writel(0x280E3D07, MEM_STTIME3); /* 250ns cycle time */
+ au_writel(0x10000000, MEM_STADDR3); /* any PCMCIA select */
+
+ // get USB Functionality pin state (device vs host drive pins)
+ pin_func = au_readl(SYS_PINFUNC) & (u32)(~0x8000);
+ // 2nd USB port is USB host
+ pin_func |= 0x8000;
+ au_writel(pin_func, SYS_PINFUNC);
+ }
#endif // defined (CONFIG_USB_OHCI)
/* Enable sys bus clock divider when IDLE state or no bus activity. */
au_writel(au_readl(SYS_POWERCTRL) | (0x3 << 5), SYS_POWERCTRL);
// Enable the RTC if not already enabled
- if (!(readb(0xac000028) & 0x20)) {
- writeb(readb(0xac000028) | 0x20, 0xac000028);
+ if (!(readb(base + 0x28) & 0x20)) {
+ writeb(readb(base + 0x28) | 0x20, base + 0x28);
au_sync();
}
// Put the clock in BCD mode
- if (readb(0xac00002C) & 0x4) { /* reg B */
- writeb(readb(0xac00002c) & ~0x4, 0xac00002c);
+ if (readb(base + 0x2C) & 0x4) { /* reg B */
+ writeb(readb(base + 0x2c) & ~0x4, base + 0x2c);
au_sync();
}
}