diff options
Diffstat (limited to 'Documentation/kernel-parameters.txt')
| -rw-r--r-- | Documentation/kernel-parameters.txt | 121 |
1 files changed, 96 insertions, 25 deletions
diff --git a/Documentation/kernel-parameters.txt b/Documentation/kernel-parameters.txt index ad2b3078e59..54ebf100e4e 100644 --- a/Documentation/kernel-parameters.txt +++ b/Documentation/kernel-parameters.txt @@ -48,6 +48,7 @@ parameter is applicable: EFI EFI Partitioning (GPT) is enabled EIDE EIDE/ATAPI support is enabled. FB The frame buffer device is enabled. + GCOV GCOV profiling is enabled. HW Appropriate hardware is enabled. IA-64 IA-64 architecture is enabled. IMA Integrity measurement architecture is enabled. @@ -56,7 +57,6 @@ parameter is applicable: ISAPNP ISA PnP code is enabled. ISDN Appropriate ISDN support is enabled. JOY Appropriate joystick support is enabled. - KMEMTRACE kmemtrace is enabled. LIBATA Libata driver is enabled LP Printer support is enabled. LOOP Loopback device support is enabled. @@ -329,11 +329,6 @@ and is between 256 and 4096 characters. It is defined in the file flushed before they will be reused, which is a lot of faster - amd_iommu_size= [HW,X86-64] - Define the size of the aperture for the AMD IOMMU - driver. Possible values are: - '32M', '64M' (default), '128M', '256M', '512M', '1G' - amijoy.map= [HW,JOY] Amiga joystick support Map of devices attached to JOY0DAT and JOY1DAT Format: <a>,<b> @@ -497,6 +492,13 @@ and is between 256 and 4096 characters. It is defined in the file Also note the kernel might malfunction if you disable some critical bits. + cmo_free_hint= [PPC] Format: { yes | no } + Specify whether pages are marked as being inactive + when they are freed. This is used in CMO environments + to determine OS memory pressure for page stealing by + a hypervisor. + Default: yes + code_bytes [X86] How many bytes of object code to print in an oops report. Range: 0 - 8192 @@ -545,6 +547,10 @@ and is between 256 and 4096 characters. It is defined in the file console=brl,ttyS0 For now, only VisioBraille is supported. + consoleblank= [KNL] The console blank (screen saver) timeout in + seconds. Defaults to 10*60 = 10mins. A value of 0 + disables the blank timer. + coredump_filter= [KNL] Change the default value for /proc/<pid>/coredump_filter. @@ -646,6 +652,13 @@ and is between 256 and 4096 characters. It is defined in the file DMA-API debugging code disables itself because the architectural default is too low. + dma_debug_driver=<driver_name> + With this option the DMA-API debugging driver + filter feature can be enabled at boot time. Just + pass the driver to filter for as the parameter. + The filter can be disabled or changed to another + driver later using sysfs. + dscc4.setup= [NET] dtc3181e= [HW,SCSI] @@ -752,12 +765,25 @@ and is between 256 and 4096 characters. It is defined in the file ia64_pal_cache_flush instead of SAL_CACHE_FLUSH. ftrace=[tracer] - [ftrace] will set and start the specified tracer + [FTRACE] will set and start the specified tracer as early as possible in order to facilitate early boot debugging. ftrace_dump_on_oops - [ftrace] will dump the trace buffers on oops. + [FTRACE] will dump the trace buffers on oops. + + ftrace_filter=[function-list] + [FTRACE] Limit the functions traced by the function + tracer at boot up. function-list is a comma separated + list of functions. This list can be changed at run + time by the set_ftrace_filter file in the debugfs + tracing directory. + + ftrace_notrace=[function-list] + [FTRACE] Do not trace the functions specified in + function-list. This list can be changed at run time + by the set_ftrace_notrace file in the debugfs + tracing directory. gamecon.map[2|3]= [HW,JOY] Multisystem joystick and NES/SNES/PSX pad @@ -771,6 +797,12 @@ and is between 256 and 4096 characters. It is defined in the file Format: off | on default: on + gcov_persist= [GCOV] When non-zero (default), profiling data for + kernel modules is saved and remains accessible via + debugfs, even when the module is unloaded/reloaded. + When zero, profiling data is discarded and associated + debugfs files are removed at module unload time. + gdth= [HW,SCSI] See header of drivers/scsi/gdth.c. @@ -873,11 +905,8 @@ and is between 256 and 4096 characters. It is defined in the file ide-core.nodma= [HW] (E)IDE subsystem Format: =0.0 to prevent dma on hda, =0.1 hdb =1.0 hdc - .vlb_clock .pci_clock .noflush .noprobe .nowerr .cdrom - .chs .ignore_cable are additional options - See Documentation/ide/ide.txt. - - idebus= [HW] (E)IDE subsystem - VLB/PCI bus speed + .vlb_clock .pci_clock .noflush .nohpa .noprobe .nowerr + .cdrom .chs .ignore_cable are additional options See Documentation/ide/ide.txt. ide-pci-generic.all-generic-ide [HW] (E)IDE subsystem @@ -914,6 +943,12 @@ and is between 256 and 4096 characters. It is defined in the file Formt: { "sha1" | "md5" } default: "sha1" + ima_tcb [IMA] + Load a policy which meets the needs of the Trusted + Computing Base. This means IMA will measure all + programs exec'd, files mmap'd for exec, and all files + opened for read by uid=0. + in2000= [HW,SCSI] See header of drivers/scsi/in2000.c. @@ -1054,24 +1089,19 @@ and is between 256 and 4096 characters. It is defined in the file use the HighMem zone if it exists, and the Normal zone if it does not. - kmemtrace.enable= [KNL,KMEMTRACE] Format: { yes | no } - Controls whether kmemtrace is enabled - at boot-time. - - kmemtrace.subbufs=n [KNL,KMEMTRACE] Overrides the number of - subbufs kmemtrace's relay channel has. Set this - higher than default (KMEMTRACE_N_SUBBUFS in code) if - you experience buffer overruns. - kgdboc= [HW] kgdb over consoles. Requires a tty driver that supports console polling. - (only serial suported for now) + (only serial supported for now) Format: <serial_device>[,baud] kmac= [MIPS] korina ethernet MAC address. Configure the RouterBoard 532 series on-chip Ethernet adapter MAC address. + kmemleak= [KNL] Boot-time kmemleak enable/disable + Valid arguments: on, off + Default: on + kstack=N [X86] Print N words from the kernel stack in oops dumps. @@ -1339,6 +1369,27 @@ and is between 256 and 4096 characters. It is defined in the file min_addr=nn[KMG] [KNL,BOOT,ia64] All physical memory below this physical address is ignored. + mini2440= [ARM,HW,KNL] + Format:[0..2][b][c][t] + Default: "0tb" + MINI2440 configuration specification: + 0 - The attached screen is the 3.5" TFT + 1 - The attached screen is the 7" TFT + 2 - The VGA Shield is attached (1024x768) + Leaving out the screen size parameter will not load + the TFT driver, and the framebuffer will be left + unconfigured. + b - Enable backlight. The TFT backlight pin will be + linked to the kernel VESA blanking code and a GPIO + LED. This parameter is not necessary when using the + VGA shield. + c - Enable the s3c camera interface. + t - Reserved for enabling touchscreen support. The + touchscreen support is not enabled in the mainstream + kernel as of 2.6.30, a preliminary port can be found + in the "bleeding edge" mini2440 support kernel at + http://repo.or.cz/w/linux-2.6/mini2440.git + mminit_loglevel= [KNL] When CONFIG_DEBUG_MEMORY_INIT is set, this parameter allows control of the logging verbosity for @@ -1400,7 +1451,7 @@ and is between 256 and 4096 characters. It is defined in the file ('y', default) or cooked coordinates ('n') mtrr_chunk_size=nn[KMG] [X86] - used for mtrr cleanup. It is largest continous chunk + used for mtrr cleanup. It is largest continuous chunk that could hold holes aka. UC entries. mtrr_gran_size=nn[KMG] [X86] @@ -1585,6 +1636,9 @@ and is between 256 and 4096 characters. It is defined in the file noinitrd [RAM] Tells the kernel not to load any configured initial RAM disk. + nointremap [X86-64, Intel-IOMMU] Do not enable interrupt + remapping. + nointroute [IA-64] nojitter [IA64] Disables jitter checking for ITC timers. @@ -1670,6 +1724,14 @@ and is between 256 and 4096 characters. It is defined in the file oprofile.timer= [HW] Use timer interrupt instead of performance counters + oprofile.cpu_type= Force an oprofile cpu type + This might be useful if you have an older oprofile + userland or if you want common events. + Format: { archperfmon } + archperfmon: [X86] Force use of architectural + perfmon on Intel CPUs instead of the + CPU specific event set. + osst= [HW,SCSI] SCSI Tape Driver Format: <buffer_size>,<write_threshold> See also Documentation/scsi/st.txt. @@ -1745,6 +1807,9 @@ and is between 256 and 4096 characters. It is defined in the file root domains (aka PCI segments, in ACPI-speak). nommconf [X86] Disable use of MMCONFIG for PCI Configuration + check_enable_amd_mmconf [X86] check for and enable + properly configured MMIO access to PCI + config space on AMD family 10h CPU nomsi [MSI] If the PCI_MSI kernel config parameter is enabled, this kernel boot option can be used to disable the use of MSI interrupts system-wide. @@ -1797,7 +1862,7 @@ and is between 256 and 4096 characters. It is defined in the file IRQ routing is enabled. noacpi [X86] Do not use ACPI for IRQ routing or for PCI scanning. - use_crs [X86] Use _CRS for PCI resource + nocrs [X86] Don't use _CRS for PCI resource allocation. routeirq Do IRQ routing for all PCI devices. This is normally done in pci_enable_device(), @@ -1834,6 +1899,12 @@ and is between 256 and 4096 characters. It is defined in the file PAGE_SIZE is used as alignment. PCI-PCI bridge can be specified, if resource windows need to be expanded. + ecrc= Enable/disable PCIe ECRC (transaction layer + end-to-end CRC checking). + bios: Use BIOS/firmware settings. This is the + the default. + off: Turn ECRC off + on: Turn ECRC on. pcie_aspm= [PCIE] Forcibly enable or disable PCIe Active State Power Management. |