aboutsummaryrefslogtreecommitdiff
path: root/Documentation/networking/slicecom.txt
diff options
context:
space:
mode:
Diffstat (limited to 'Documentation/networking/slicecom.txt')
-rw-r--r--Documentation/networking/slicecom.txt369
1 files changed, 0 insertions, 369 deletions
diff --git a/Documentation/networking/slicecom.txt b/Documentation/networking/slicecom.txt
deleted file mode 100644
index c82c0cf981b..00000000000
--- a/Documentation/networking/slicecom.txt
+++ /dev/null
@@ -1,369 +0,0 @@
-
-SliceCOM adapter user's documentation - for the 0.51 driver version
-
-Written by Bartók István <bartoki@itc.hu>
-
-English translation: Lakatos György <gyuri@itc.hu>
-Mon Dec 11 15:28:42 CET 2000
-
-Last modified: Wed Aug 29 17:25:37 CEST 2001
-
------------------------------------------------------------------
-
-Usage:
-
-Compiling the kernel:
-
-Code maturity level options
- [*] Prompt for development and/or incomplete code/drivers
-
-Network device support
- Wan interfaces
- <M> MultiGate (COMX) synchronous
- <M> Support for MUNICH based boards: SliceCOM, PCICOM (NEW)
- <M> Support for HDLC and syncPPP...
-
-
-Loading the modules:
-
-modprobe comx
-
-modprobe comx-proto-ppp # module for Cisco-HDLC and SyncPPP protocols
-
-modprobe comx-hw-munich # the module logs information by the kernel
- # about the detected boards
-
-
-Configuring the board:
-
-# This interface will use the Cisco-HDLC line protocol,
-# the timeslices assigned are 1,2 (128 KiBit line speed)
-# (the first data timeslice in the G.703 frame is no. 1)
-#
-mkdir /proc/comx/comx0.1/
-echo slicecom >/proc/comx/comx0.1/boardtype
-echo hdlc >/proc/comx/comx0.1/protocol
-echo 1 2 >/proc/comx/comx0.1/timeslots
-
-
-# This interface uses SyncPPP line protocol, the assigned
-# is no. 3 (64 KiBit line speed)
-#
-mkdir /proc/comx/comx0.2/
-echo slicecom >/proc/comx/comx0.2/boardtype
-echo ppp >/proc/comx/comx0.2/protocol
-echo 3 >/proc/comx/comx0.2/timeslots
-
-...
-
-ifconfig comx0.1 up
-ifconfig comx0.2 up
-
------------------------------------------------------------------
-
-The COMX interfaces use a 10 packet transmit queue by default, however WAN
-networks sometimes use bigger values (20 to 100), to utilize the line better
-by large traffic (though the line delay increases because of more packets
-join the queue).
-
-# ifconfig comx0 txqueuelen 50
-
-This option is only supported by the ifconfig command of the later
-distributions, which came with 2.2 kernels, such as RedHat 6.1 or Debian 2.2.
-
-You can download a newer netbase packet from
-http://www.debian.org/~rcw/2.2/netbase/ for Debian 2.1, which has a new
-ifconfig. You can get further information about using 2.2 kernel with
-Debian 2.1 from http://www.debian.org/releases/stable/running-kernel-2.2
-
------------------------------------------------------------------
-
-The SliceCom LEDs:
-
-red - on, if the interface is unconfigured, or it gets Remote Alarm-s
-green - on, if the board finds frame-sync in the received signal
-
-A bit more detailed:
-
-red: green: meaning:
-
-- - no frame-sync, no signal received, or signal SNAFU.
-- on "Everything is OK"
-on on Reception is ok, but the remote end sends Remote Alarm
-on - The interface is unconfigured
-
------------------------------------------------------------------
-
-A more detailed description of the hardware setting options:
-
-The general and the protocol layer options described in the 'comx.txt' file
-apply to the SliceCom as well, I only summarize the SliceCom hardware specific
-settings below.
-
-The '/proc/comx' configuring interface:
-
-An interface directory should be created for every timeslot group with
-'mkdir', e,g: 'comx0', 'comx1' etc. The timeslots can be assigned here to the
-specific interface. The Cisco-like naming convention (serial3:1 - first
-timeslot group of the 3rd. board) can't be used here, because these mean IP
-aliasing in Linux.
-
-You can give any meaningful name to keep the configuration clear;
-e.g: 'comx0.1', 'comx0.2', 'comx1.1', comx1.2', if you have two boards
-with two interfaces each.
-
-Settings, which apply to the board:
-
-Neither 'io' nor 'irq' settings required, the driver uses the resources
-given by the PCI BIOS.
-
-comx0/boardnum - board number of the SliceCom in the PC (using the 'natural'
- PCI order) as listed in '/proc/pci' or the output of the
- 'lspci' command, generally the slots nearer to the motherboard
- PCI driver chips have the lower numbers.
-
- Default: 0 (the counting starts with 0)
-
-Though the options below are to be set on a single interface, they apply to the
-whole board. The restriction, to use them on 'UP' interfaces, is because the
-command sequence below could lead to unpredictable results.
-
- # echo 0 >boardnum
- # echo internal >clock_source
- # echo 1 >boardnum
-
-The sequence would set the clock source of board 0.
-
-These settings will persist after all the interfaces are cleared, but are
-cleared when the driver module is unloaded and loaded again.
-
-comx0/clock_source - source of the transmit clock
- Usage:
-
- # echo line >/proc/comx/comx0/clock_source
- # echo internal >/proc/comx/comx0/clock_source
-
- line - The Tx clock is being decoded if the input data stream,
- if no clock seen on the input, then the board will use it's
- own clock generator.
-
- internal - The Tx clock is supplied by the builtin clock generator.
-
- Default: line
-
- Normally, the telecommunication company's end device (the HDSL
- modem) provides the Tx clock, that's why 'line' is the default.
-
-comx0/framing - Switching CRC4 off/on
-
- CRC4: 16 PCM frames (The 32 64Kibit channels are multiplexed into a
- PCM frame, nothing to do with HDLC frames) are divided into 2x8
- groups, each group has a 4 bit CRC.
-
- # echo crc4 >/proc/comx/comx0/framing
- # echo no-crc4 >/proc/comx/comx0/framing
-
- Default is 'crc4', the Hungarian MATAV lines behave like this.
- The traffic generally passes if this setting on both ends don't match.
-
-comx0/linecode - Setting the line coding
-
- # echo hdb3 >/proc/comx/comx0/linecode
- # echo ami >/proc/comx/comx0/linecode
-
- Default a 'hdb3', MATAV lines use this.
-
- (AMI coding is rarely used with E1 lines). Frame sync may occur, if
- this setting doesn't match the other end's, but CRC4 and data errors
- will come, which will result in CRC errors on HDLC/SyncPPP level.
-
-comx0/reg - direct access to the board's MUNICH (reg) and FALC (lbireg)
-comx0/lbireg circuit's registers
-
- # echo >reg 0x04 0x0 - write 0 to register 4
- # echo >reg 0x104 - write the contents of register 4 with
- printk() to syslog
-
-WARNING! These are only for development purposes, messing with this will
- result much trouble!
-
-comx0/loopback - Places a loop to the board's G.703 signals
-
- # echo none >/proc/comx/comx0/loopback
- # echo local >/proc/comx/comx0/loopback
- # echo remote >/proc/comx/comx0/loopback
-
- none - normal operation, no loop
- local - the board receives it's own output
- remote - the board sends the received data to the remote side
-
- Default: none
-
------------------------------------------------------------------
-
-Interface (channel group in Cisco terms) settings:
-
-comx0/timeslots - which timeslots belong to the given interface
-
- Setting:
-
- # echo '1 5 2 6 7 8' >/proc/comx/comx0/timeslots
-
- # cat /proc/comx/comx0/timeslots
- 1 2 5 6 7 8
- #
-
- Finding a timeslot:
-
- # grep ' 4' /proc/comx/comx*/timeslots
- /proc/comx/comx0/timeslots:1 3 4 5 6
- #
-
- The timeslots can be in any order, '1 2 3' is the same as '1 3 2'.
-
- The interface has to be DOWN during the setting ('ifconfig comx0
- down'), but the other interfaces could operate normally.
-
- The driver checks if the assigned timeslots are vacant, if not, then
- the setting won't be applied.
-
- The timeslot values are treated as decimal numbers, not to misunderstand
- values of 08, 09 form.
-
------------------------------------------------------------------
-
-Checking the interface and board status:
-
-- Lines beginning with ' ' (space) belong to the original output, the lines
-which begin with '//' are the comments.
-
- papaya:~$ cat /proc/comx/comx1/status
- Interface administrative status is UP, modem status is UP, protocol is UP
- Modem status changes: 0, Transmitter status is IDLE, tbusy: 0
- Interface load (input): 978376 / 947808 / 951024 bits/s (5s/5m/15m)
- (output): 978376 / 947848 / 951024 bits/s (5s/5m/15m)
- Debug flags: none
- RX errors: len: 22, overrun: 1, crc: 0, aborts: 0
- buffer overrun: 0, pbuffer overrun: 0
- TX errors: underrun: 0
- Line keepalive (value: 10) status UP [0]
-
-// The hardware specific part starts here:
- Controller status:
- No alarms
-
-// Alarm:
-//
-// No alarms - Everything OK
-//
-// LOS - Loss Of Signal - No signal sensed on the input
-// AIS - Alarm Indication Signal - The remote side sends '11111111'-s,
-// it tells, that there's an error condition, or it's not
-// initialised.
-// AUXP - Auxiliary Pattern Indication - 01010101.. received.
-// LFA - Loss of Frame Alignment - no frame sync received.
-// RRA - Receive Remote Alarm - the remote end's OK, but signals error cond.
-// LMFA - Loss of CRC4 Multiframe Alignment - no CRC4 multiframe sync.
-// NMF - No Multiframe alignment Found after 400 msec - no such alarm using
-// no-crc4 or crc4 framing, see below.
-//
-// Other possible error messages:
-//
-// Transmit Line Short - the board felt, that it's output is short-circuited,
-// so it switched the transmission off. (The board can't definitely tell,
-// that it's output is short-circuited.)
-
-// Chained list of the received packets, for debug purposes:
-
- Rx ring:
- rafutott: 0
- lastcheck: 50845731, jiffies: 51314281
- base: 017b1858
- rx_desc_ptr: 0
- rx_desc_ptr: 017b1858
- hw_curr_ptr: 017b1858
- 06040000 017b1868 017b1898 c016ff00
- 06040000 017b1878 017b1e9c c016ff00
- 46040000 017b1888 017b24a0 c016ff00
- 06040000 017b1858 017b2aa4 c016ff00
-
-// All the interfaces using the board: comx1, using the 1,2,...16 timeslots,
-// comx2, using timeslot 17, etc.
-
- Interfaces using this board: (channel-group, interface, timeslots)
- 0 comx1: 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16
- 1 comx2: 17
- 2 comx3: 18
- 3 comx4: 19
- 4 comx5: 20
- 5 comx6: 21
- 6 comx7: 22
- 7 comx8: 23
- 8 comx9: 24
- 9 comx10: 25
- 10 comx11: 26
- 11 comx12: 27
- 12 comx13: 28
- 13 comx14: 29
- 14 comx15: 30
- 15 comx16: 31
-
-// The number of events handled by the driver during an interrupt cycle:
-
- Interrupt work histogram:
- hist[ 0]: 0 hist[ 1]: 2 hist[ 2]: 18574 hist[ 3]: 79
- hist[ 4]: 14 hist[ 5]: 1 hist[ 6]: 0 hist[ 7]: 1
- hist[ 8]: 0 hist[ 9]: 7
-
-// The number of packets to send in the Tx ring, when a new one arrived:
-
- Tx ring histogram:
- hist[ 0]: 2329 hist[ 1]: 0 hist[ 2]: 0 hist[ 3]: 0
-
-// The error counters of the E1 interface, according to the RFC2495,
-// (similar to the Cisco "show controllers e1" command's output:
-// http://www.cisco.com/univercd/cc/td/doc/product/software/ios11/rbook/rinterfc.htm#xtocid25669126)
-
-Data in current interval (91 seconds elapsed):
- 9516 Line Code Violations, 65 Path Code Violations, 2 E-Bit Errors
- 0 Slip Secs, 2 Fr Loss Secs, 2 Line Err Secs, 0 Degraded Mins
- 0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 11 Unavail Secs
-Data in Interval 1 (15 minutes):
- 0 Line Code Violations, 0 Path Code Violations, 0 E-Bit Errors
- 0 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins
- 0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 0 Unavail Secs
-Data in last 4 intervals (1 hour):
- 0 Line Code Violations, 0 Path Code Violations, 0 E-Bit Errors
- 0 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins
- 0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 0 Unavail Secs
-Data in last 96 intervals (24 hours):
- 0 Line Code Violations, 0 Path Code Violations, 0 E-Bit Errors
- 0 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins
- 0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 0 Unavail Secs
-
------------------------------------------------------------------
-
-Some unique options, (may get into the driver later):
-Treat them very carefully, these can cause much trouble!
-
- modified CRC-4, for improved interworking of CRC-4 and non-CRC-4
- devices: (see page 107 and g706 Annex B)
- lbireg[ 0x1b ] |= 0x08
- lbireg[ 0x1c ] |= 0xc0
-
- - The NMF - 'No Multiframe alignment Found after 400 msec' alarm
- comes into account.
-
- FALC - the line driver chip.
- local loop - I hear my transmission back.
- remote loop - I echo the remote transmission back.
-
- Something useful for finding errors:
-
- - local loop for timeslot 1 in the FALC chip:
-
- # echo >lbireg 0x1d 0x21
-
- - Switching the loop off:
-
- # echo >lbireg 0x1d 0x00