aboutsummaryrefslogtreecommitdiff
path: root/Documentation/networking
diff options
context:
space:
mode:
Diffstat (limited to 'Documentation/networking')
-rw-r--r--Documentation/networking/00-INDEX3
-rw-r--r--Documentation/networking/sk98lin.txt568
2 files changed, 0 insertions, 571 deletions
diff --git a/Documentation/networking/00-INDEX b/Documentation/networking/00-INDEX
index 153d84d281e..d63f480afb7 100644
--- a/Documentation/networking/00-INDEX
+++ b/Documentation/networking/00-INDEX
@@ -96,9 +96,6 @@ routing.txt
- the new routing mechanism
shaper.txt
- info on the module that can shape/limit transmitted traffic.
-sk98lin.txt
- - Marvell Yukon Chipset / SysKonnect SK-98xx compliant Gigabit
- Ethernet Adapter family driver info
skfp.txt
- SysKonnect FDDI (SK-5xxx, Compaq Netelligent) driver info.
smc9.txt
diff --git a/Documentation/networking/sk98lin.txt b/Documentation/networking/sk98lin.txt
deleted file mode 100644
index 8590a954df1..00000000000
--- a/Documentation/networking/sk98lin.txt
+++ /dev/null
@@ -1,568 +0,0 @@
-(C)Copyright 1999-2004 Marvell(R).
-All rights reserved
-===========================================================================
-
-sk98lin.txt created 13-Feb-2004
-
-Readme File for sk98lin v6.23
-Marvell Yukon/SysKonnect SK-98xx Gigabit Ethernet Adapter family driver for LINUX
-
-This file contains
- 1 Overview
- 2 Required Files
- 3 Installation
- 3.1 Driver Installation
- 3.2 Inclusion of adapter at system start
- 4 Driver Parameters
- 4.1 Per-Port Parameters
- 4.2 Adapter Parameters
- 5 Large Frame Support
- 6 VLAN and Link Aggregation Support (IEEE 802.1, 802.1q, 802.3ad)
- 7 Troubleshooting
-
-===========================================================================
-
-
-1 Overview
-===========
-
-The sk98lin driver supports the Marvell Yukon and SysKonnect
-SK-98xx/SK-95xx compliant Gigabit Ethernet Adapter on Linux. It has
-been tested with Linux on Intel/x86 machines.
-***
-
-
-2 Required Files
-=================
-
-The linux kernel source.
-No additional files required.
-***
-
-
-3 Installation
-===============
-
-It is recommended to download the latest version of the driver from the
-SysKonnect web site www.syskonnect.com. If you have downloaded the latest
-driver, the Linux kernel has to be patched before the driver can be
-installed. For details on how to patch a Linux kernel, refer to the
-patch.txt file.
-
-3.1 Driver Installation
-------------------------
-
-The following steps describe the actions that are required to install
-the driver and to start it manually. These steps should be carried
-out for the initial driver setup. Once confirmed to be ok, they can
-be included in the system start.
-
-NOTE 1: To perform the following tasks you need 'root' access.
-
-NOTE 2: In case of problems, please read the section "Troubleshooting"
- below.
-
-The driver can either be integrated into the kernel or it can be compiled
-as a module. Select the appropriate option during the kernel
-configuration.
-
-Compile/use the driver as a module
-----------------------------------
-To compile the driver, go to the directory /usr/src/linux and
-execute the command "make menuconfig" or "make xconfig" and proceed as
-follows:
-
-To integrate the driver permanently into the kernel, proceed as follows:
-
-1. Select the menu "Network device support" and then "Ethernet(1000Mbit)"
-2. Mark "Marvell Yukon Chipset / SysKonnect SK-98xx family support"
- with (*)
-3. Build a new kernel when the configuration of the above options is
- finished.
-4. Install the new kernel.
-5. Reboot your system.
-
-To use the driver as a module, proceed as follows:
-
-1. Enable 'loadable module support' in the kernel.
-2. For automatic driver start, enable the 'Kernel module loader'.
-3. Select the menu "Network device support" and then "Ethernet(1000Mbit)"
-4. Mark "Marvell Yukon Chipset / SysKonnect SK-98xx family support"
- with (M)
-5. Execute the command "make modules".
-6. Execute the command "make modules_install".
- The appropriate modules will be installed.
-7. Reboot your system.
-
-
-Load the module manually
-------------------------
-To load the module manually, proceed as follows:
-
-1. Enter "modprobe sk98lin".
-2. If a Marvell Yukon or SysKonnect SK-98xx adapter is installed in
- your computer and you have a /proc file system, execute the command:
- "ls /proc/net/sk98lin/"
- This should produce an output containing a line with the following
- format:
- eth0 eth1 ...
- which indicates that your adapter has been found and initialized.
-
- NOTE 1: If you have more than one Marvell Yukon or SysKonnect SK-98xx
- adapter installed, the adapters will be listed as 'eth0',
- 'eth1', 'eth2', etc.
- For each adapter, repeat steps 3 and 4 below.
-
- NOTE 2: If you have other Ethernet adapters installed, your Marvell
- Yukon or SysKonnect SK-98xx adapter will be mapped to the
- next available number, e.g. 'eth1'. The mapping is executed
- automatically.
- The module installation message (displayed either in a system
- log file or on the console) prints a line for each adapter
- found containing the corresponding 'ethX'.
-
-3. Select an IP address and assign it to the respective adapter by
- entering:
- ifconfig eth0 <ip-address>
- With this command, the adapter is connected to the Ethernet.
-
- SK-98xx Gigabit Ethernet Server Adapters: The yellow LED on the adapter
- is now active, the link status LED of the primary port is active and
- the link status LED of the secondary port (on dual port adapters) is
- blinking (if the ports are connected to a switch or hub).
- SK-98xx V2.0 Gigabit Ethernet Adapters: The link status LED is active.
- In addition, you will receive a status message on the console stating
- "ethX: network connection up using port Y" and showing the selected
- connection parameters (x stands for the ethernet device number
- (0,1,2, etc), y stands for the port name (A or B)).
-
- NOTE: If you are in doubt about IP addresses, ask your network
- administrator for assistance.
-
-4. Your adapter should now be fully operational.
- Use 'ping <otherstation>' to verify the connection to other computers
- on your network.
-5. To check the adapter configuration view /proc/net/sk98lin/[devicename].
- For example by executing:
- "cat /proc/net/sk98lin/eth0"
-
-Unload the module
------------------
-To stop and unload the driver modules, proceed as follows:
-
-1. Execute the command "ifconfig eth0 down".
-2. Execute the command "rmmod sk98lin".
-
-3.2 Inclusion of adapter at system start
------------------------------------------
-
-Since a large number of different Linux distributions are
-available, we are unable to describe a general installation procedure
-for the driver module.
-Because the driver is now integrated in the kernel, installation should
-be easy, using the standard mechanism of your distribution.
-Refer to the distribution's manual for installation of ethernet adapters.
-
-***
-
-4 Driver Parameters
-====================
-
-Parameters can be set at the command line after the module has been
-loaded with the command 'modprobe'.
-In some distributions, the configuration tools are able to pass parameters
-to the driver module.
-
-If you use the kernel module loader, you can set driver parameters
-in the file /etc/modprobe.conf (or /etc/modules.conf in 2.4 or earlier).
-To set the driver parameters in this file, proceed as follows:
-
-1. Insert a line of the form :
- options sk98lin ...
- For "...", the same syntax is required as described for the command
- line parameters of modprobe below.
-2. To activate the new parameters, either reboot your computer
- or
- unload and reload the driver.
- The syntax of the driver parameters is:
-
- modprobe sk98lin parameter=value1[,value2[,value3...]]
-
- where value1 refers to the first adapter, value2 to the second etc.
-
-NOTE: All parameters are case sensitive. Write them exactly as shown
- below.
-
-Example:
-Suppose you have two adapters. You want to set auto-negotiation
-on the first adapter to ON and on the second adapter to OFF.
-You also want to set DuplexCapabilities on the first adapter
-to FULL, and on the second adapter to HALF.
-Then, you must enter:
-
- modprobe sk98lin AutoNeg_A=On,Off DupCap_A=Full,Half
-
-NOTE: The number of adapters that can be configured this way is
- limited in the driver (file skge.c, constant SK_MAX_CARD_PARAM).
- The current limit is 16. If you happen to install
- more adapters, adjust this and recompile.
-
-
-4.1 Per-Port Parameters
-------------------------
-
-These settings are available for each port on the adapter.
-In the following description, '?' stands for the port for
-which you set the parameter (A or B).
-
-Speed
------
-Parameter: Speed_?
-Values: 10, 100, 1000, Auto
-Default: Auto
-
-This parameter is used to set the speed capabilities. It is only valid
-for the SK-98xx V2.0 copper adapters.
-Usually, the speed is negotiated between the two ports during link
-establishment. If this fails, a port can be forced to a specific setting
-with this parameter.
-
-Auto-Negotiation
-----------------
-Parameter: AutoNeg_?
-Values: On, Off, Sense
-Default: On
-
-The "Sense"-mode automatically detects whether the link partner supports
-auto-negotiation or not.
-
-Duplex Capabilities
--------------------
-Parameter: DupCap_?
-Values: Half, Full, Both
-Default: Both
-
-This parameters is only relevant if auto-negotiation for this port is
-not set to "Sense". If auto-negotiation is set to "On", all three values
-are possible. If it is set to "Off", only "Full" and "Half" are allowed.
-This parameter is useful if your link partner does not support all
-possible combinations.
-
-Flow Control
-------------
-Parameter: FlowCtrl_?
-Values: Sym, SymOrRem, LocSend, None
-Default: SymOrRem
-
-This parameter can be used to set the flow control capabilities the
-port reports during auto-negotiation. It can be set for each port
-individually.
-Possible modes:
- -- Sym = Symmetric: both link partners are allowed to send
- PAUSE frames
- -- SymOrRem = SymmetricOrRemote: both or only remote partner
- are allowed to send PAUSE frames
- -- LocSend = LocalSend: only local link partner is allowed
- to send PAUSE frames
- -- None = no link partner is allowed to send PAUSE frames
-
-NOTE: This parameter is ignored if auto-negotiation is set to "Off".
-
-Role in Master-Slave-Negotiation (1000Base-T only)
---------------------------------------------------
-Parameter: Role_?
-Values: Auto, Master, Slave
-Default: Auto
-
-This parameter is only valid for the SK-9821 and SK-9822 adapters.
-For two 1000Base-T ports to communicate, one must take the role of the
-master (providing timing information), while the other must be the
-slave. Usually, this is negotiated between the two ports during link
-establishment. If this fails, a port can be forced to a specific setting
-with this parameter.
-
-
-4.2 Adapter Parameters
------------------------
-
-Connection Type (SK-98xx V2.0 copper adapters only)
----------------
-Parameter: ConType
-Values: Auto, 100FD, 100HD, 10FD, 10HD
-Default: Auto
-
-The parameter 'ConType' is a combination of all five per-port parameters
-within one single parameter. This simplifies the configuration of both ports
-of an adapter card! The different values of this variable reflect the most
-meaningful combinations of port parameters.
-
-The following table shows the values of 'ConType' and the corresponding
-combinations of the per-port parameters:
-
- ConType | DupCap AutoNeg FlowCtrl Role Speed
- ----------+------------------------------------------------------
- Auto | Both On SymOrRem Auto Auto
- 100FD | Full Off None Auto (ignored) 100
- 100HD | Half Off None Auto (ignored) 100
- 10FD | Full Off None Auto (ignored) 10
- 10HD | Half Off None Auto (ignored) 10
-
-Stating any other port parameter together with this 'ConType' variable
-will result in a merged configuration of those settings. This due to
-the fact, that the per-port parameters (e.g. Speed_? ) have a higher
-priority than the combined variable 'ConType'.
-
-NOTE: This parameter is always used on both ports of the adapter card.
-
-Interrupt Moderation
---------------------
-Parameter: Moderation
-Values: None, Static, Dynamic
-Default: None
-
-Interrupt moderation is employed to limit the maximum number of interrupts
-the driver has to serve. That is, one or more interrupts (which indicate any
-transmit or receive packet to be processed) are queued until the driver
-processes them. When queued interrupts are to be served, is determined by the
-'IntsPerSec' parameter, which is explained later below.
-
-Possible modes:
-
- -- None - No interrupt moderation is applied on the adapter card.
- Therefore, each transmit or receive interrupt is served immediately
- as soon as it appears on the interrupt line of the adapter card.
-
- -- Static - Interrupt moderation is applied on the adapter card.
- All transmit and receive interrupts are queued until a complete
- moderation interval ends. If such a moderation interval ends, all
- queued interrupts are processed in one big bunch without any delay.
- The term 'static' reflects the fact, that interrupt moderation is
- always enabled, regardless how much network load is currently
- passing via a particular interface. In addition, the duration of
- the moderation interval has a fixed length that never changes while
- the driver is operational.
-
- -- Dynamic - Interrupt moderation might be applied on the adapter card,
- depending on the load of the system. If the driver detects that the
- system load is too high, the driver tries to shield the system against
- too much network load by enabling interrupt moderation. If - at a later
- time - the CPU utilization decreases again (or if the network load is
- negligible) the interrupt moderation will automatically be disabled.
-
-Interrupt moderation should be used when the driver has to handle one or more
-interfaces with a high network load, which - as a consequence - leads also to a
-high CPU utilization. When moderation is applied in such high network load
-situations, CPU load might be reduced by 20-30%.
-
-NOTE: The drawback of using interrupt moderation is an increase of the round-
-trip-time (RTT), due to the queueing and serving of interrupts at dedicated
-moderation times.
-
-Interrupts per second
----------------------
-Parameter: IntsPerSec
-Values: 30...40000 (interrupts per second)
-Default: 2000
-
-This parameter is only used if either static or dynamic interrupt moderation
-is used on a network adapter card. Using this parameter if no moderation is
-applied will lead to no action performed.
-
-This parameter determines the length of any interrupt moderation interval.
-Assuming that static interrupt moderation is to be used, an 'IntsPerSec'
-parameter value of 2000 will lead to an interrupt moderation interval of
-500 microseconds.
-
-NOTE: The duration of the moderation interval is to be chosen with care.
-At first glance, selecting a very long duration (e.g. only 100 interrupts per
-second) seems to be meaningful, but the increase of packet-processing delay
-is tremendous. On the other hand, selecting a very short moderation time might
-compensate the use of any moderation being applied.
-
-
-Preferred Port
---------------
-Parameter: PrefPort
-Values: A, B
-Default: A
-
-This is used to force the preferred port to A or B (on dual-port network
-adapters). The preferred port is the one that is used if both are detected
-as fully functional.
-
-RLMT Mode (Redundant Link Management Technology)
-------------------------------------------------
-Parameter: RlmtMode
-Values: CheckLinkState,CheckLocalPort, CheckSeg, DualNet
-Default: CheckLinkState
-
-RLMT monitors the status of the port. If the link of the active port
-fails, RLMT switches immediately to the standby link. The virtual link is
-maintained as long as at least one 'physical' link is up.
-
-Possible modes:
-
- -- CheckLinkState - Check link state only: RLMT uses the link state
- reported by the adapter hardware for each individual port to
- determine whether a port can be used for all network traffic or
- not.
-
- -- CheckLocalPort - In this mode, RLMT monitors the network path
- between the two ports of an adapter by regularly exchanging packets
- between them. This mode requires a network configuration in which
- the two ports are able to "see" each other (i.e. there must not be
- any router between the ports).
-
- -- CheckSeg - Check local port and segmentation: This mode supports the
- same functions as the CheckLocalPort mode and additionally checks
- network segmentation between the ports. Therefore, this mode is only
- to be used if Gigabit Ethernet switches are installed on the network
- that have been configured to use the Spanning Tree protocol.
-
- -- DualNet - In this mode, ports A and B are used as separate devices.
- If you have a dual port adapter, port A will be configured as eth0
- and port B as eth1. Both ports can be used independently with
- distinct IP addresses. The preferred port setting is not used.
- RLMT is turned off.
-
-NOTE: RLMT modes CLP and CLPSS are designed to operate in configurations
- where a network path between the ports on one adapter exists.
- Moreover, they are not designed to work where adapters are connected
- back-to-back.
-***
-
-
-5 Large Frame Support
-======================
-
-The driver supports large frames (also called jumbo frames). Using large
-frames can result in an improved throughput if transferring large amounts
-of data.
-To enable large frames, set the MTU (maximum transfer unit) of the
-interface to the desired value (up to 9000), execute the following
-command:
- ifconfig eth0 mtu 9000
-This will only work if you have two adapters connected back-to-back
-or if you use a switch that supports large frames. When using a switch,
-it should be configured to allow large frames and auto-negotiation should
-be set to OFF. The setting must be configured on all adapters that can be
-reached by the large frames. If one adapter is not set to receive large
-frames, it will simply drop them.
-
-You can switch back to the standard ethernet frame size by executing the
-following command:
- ifconfig eth0 mtu 1500
-
-To permanently configure this setting, add a script with the 'ifconfig'
-line to the system startup sequence (named something like "S99sk98lin"
-in /etc/rc.d/rc2.d).
-***
-
-
-6 VLAN and Link Aggregation Support (IEEE 802.1, 802.1q, 802.3ad)
-==================================================================
-
-The Marvell Yukon/SysKonnect Linux drivers are able to support VLAN and
-Link Aggregation according to IEEE standards 802.1, 802.1q, and 802.3ad.
-These features are only available after installation of open source
-modules available on the Internet:
-For VLAN go to: http://www.candelatech.com/~greear/vlan.html
-For Link Aggregation go to: http://www.st.rim.or.jp/~yumo
-
-NOTE: SysKonnect GmbH does not offer any support for these open source
- modules and does not take the responsibility for any kind of
- failures or problems arising in connection with these modules.
-
-NOTE: Configuring Link Aggregation on a SysKonnect dual link adapter may
- cause problems when unloading the driver.
-
-
-7 Troubleshooting
-==================
-
-If any problems occur during the installation process, check the
-following list:
-
-
-Problem: The SK-98xx adapter cannot be found by the driver.
-Solution: In /proc/pci search for the following entry:
- 'Ethernet controller: SysKonnect SK-98xx ...'
- If this entry exists, the SK-98xx or SK-98xx V2.0 adapter has
- been found by the system and should be operational.
- If this entry does not exist or if the file '/proc/pci' is not
- found, there may be a hardware problem or the PCI support may
- not be enabled in your kernel.
- The adapter can be checked using the diagnostics program which
- is available on the SysKonnect web site:
- www.syskonnect.com
-
- Some COMPAQ machines have problems dealing with PCI under Linux.
- This problem is described in the 'PCI howto' document
- (included in some distributions or available from the
- web, e.g. at 'www.linux.org').
-
-
-Problem: Programs such as 'ifconfig' or 'route' cannot be found or the
- error message 'Operation not permitted' is displayed.
-Reason: You are not logged in as user 'root'.
-Solution: Logout and login as 'root' or change to 'root' via 'su'.
-
-
-Problem: Upon use of the command 'ping <address>' the message
- "ping: sendto: Network is unreachable" is displayed.
-Reason: Your route is not set correctly.
-Solution: If you are using RedHat, you probably forgot to set up the
- route in the 'network configuration'.
- Check the existing routes with the 'route' command and check
- if an entry for 'eth0' exists, and if so, if it is set correctly.
-
-
-Problem: The driver can be started, the adapter is connected to the
- network, but you cannot receive or transmit any packets;
- e.g. 'ping' does not work.
-Reason: There is an incorrect route in your routing table.
-Solution: Check the routing table with the command 'route' and read the
- manual help pages dealing with routes (enter 'man route').
-
-NOTE: Although the 2.2.x kernel versions generate the routing entry
- automatically, problems of this kind may occur here as well. We've
- come across a situation in which the driver started correctly at
- system start, but after the driver has been removed and reloaded,
- the route of the adapter's network pointed to the 'dummy0'device
- and had to be corrected manually.
-
-
-Problem: Your computer should act as a router between multiple
- IP subnetworks (using multiple adapters), but computers in
- other subnetworks cannot be reached.
-Reason: Either the router's kernel is not configured for IP forwarding
- or the routing table and gateway configuration of at least one
- computer is not working.
-
-Problem: Upon driver start, the following error message is displayed:
- "eth0: -- ERROR --
- Class: internal Software error
- Nr: 0xcc
- Msg: SkGeInitPort() cannot init running ports"
-Reason: You are using a driver compiled for single processor machines
- on a multiprocessor machine with SMP (Symmetric MultiProcessor)
- kernel.
-Solution: Configure your kernel appropriately and recompile the kernel or
- the modules.
-
-
-
-If your problem is not listed here, please contact SysKonnect's technical
-support for help (linux@syskonnect.de).
-When contacting our technical support, please ensure that the following
-information is available:
-- System Manufacturer and HW Informations (CPU, Memory... )
-- PCI-Boards in your system
-- Distribution
-- Kernel version
-- Driver version
-***
-
-
-
-***End of Readme File***