diff options
Diffstat (limited to 'Documentation/video4linux/cx2341x/fw-decoder-api.txt')
| -rw-r--r-- | Documentation/video4linux/cx2341x/fw-decoder-api.txt | 58 |
1 files changed, 18 insertions, 40 deletions
diff --git a/Documentation/video4linux/cx2341x/fw-decoder-api.txt b/Documentation/video4linux/cx2341x/fw-decoder-api.txt index 78bf5f21e51..8c317b7a4fc 100644 --- a/Documentation/video4linux/cx2341x/fw-decoder-api.txt +++ b/Documentation/video4linux/cx2341x/fw-decoder-api.txt @@ -21,7 +21,7 @@ Param[0] 0 based frame number in GOP to begin playback from. Param[1] Specifies the number of muted audio frames to play before normal - audio resumes. + audio resumes. (This is not implemented in the firmware, leave at 0) ------------------------------------------------------------------------------- @@ -32,6 +32,10 @@ Description playback stops at specified PTS. Param[0] Display 0=last frame, 1=black + Note: this takes effect immediately, so if you want to wait for a PTS, + then use '0', otherwise the screen goes to black at once. + You can call this later (even if there is no playback) with a 1 value + to set the screen to black. Param[1] PTS low Param[2] @@ -60,8 +64,12 @@ Param[0] 31 Speed: '0' slow '1' fast + Note: n is limited to 2. Anything higher does not result in + faster playback. Instead the host should start dropping frames. Param[1] Direction: 0=forward, 1=reverse + Note: to make reverse playback work you have to write full GOPs in + reverse order. Param[2] Picture mask: 1=I frames @@ -69,13 +77,16 @@ Param[2] 7=I, P, B frames Param[3] B frames per GOP (for reverse play only) + Note: for reverse playback the Picture Mask should be set to I or I, P. + Adding B frames to the mask will result in corrupt video. This field + has to be set to the correct value in order to keep the timing correct. Param[4] Mute audio: 0=disable, 1=enable Param[5] Display 0=frame, 1=field Param[6] Specifies the number of muted audio frames to play before normal audio - resumes. + resumes. (Not implemented in the firmware, leave at 0) ------------------------------------------------------------------------------- @@ -212,6 +223,7 @@ Description Select audio mode Param[0] Dual mono mode action + 0=Stereo, 1=Left, 2=Right, 3=Mono, 4=Swap, -1=Unchanged Param[1] Stereo mode action: 0=Stereo, 1=Left, 2=Right, 3=Mono, 4=Swap, -1=Unchanged @@ -224,7 +236,10 @@ Description Setup firmware to notify the host about a particular event. Counterpart to API 0xD5 Param[0] - Event: 0=Audio mode change between stereo and dual channel + Event: 0=Audio mode change between mono, (joint) stereo and dual channel. + Event: 3=Decoder started + Event: 4=Unknown: goes off 10-15 times per second while decoding. + Event: 5=Some sync event: goes off once per frame. Param[1] Notification 0=disabled, 1=enabled Param[2] @@ -273,43 +288,6 @@ Param[3] ------------------------------------------------------------------------------- -Name CX2341X_DEC_SET_AUDIO_OUTPUT -Enum 27/0x1B -Description - Select audio output format -Param[0] - Bitmask: - 0:1 Data size: - '00' 16 bit - '01' 20 bit - '10' 24 bit - 2:7 Unused - 8:9 Mode: - '00' 2 channels - '01' 4 channels - '10' 6 channels - '11' 6 channels with one line data mode - (for left justified MSB first mode, 20 bit only) - 10:11 Unused - 12:13 Channel format: - '00' right justified MSB first mode - '01' left justified MSB first mode - '10' I2S mode - 14:15 Unused - 16:21 Right justify bit count - 22:31 Unused - -------------------------------------------------------------------------------- - -Name CX2341X_DEC_SET_AV_DELAY -Enum 28/0x1C -Description - Set audio/video delay in 90Khz ticks -Param[0] - 0=A/V in sync, negative=audio lags, positive=video lags - -------------------------------------------------------------------------------- - Name CX2341X_DEC_SET_PREBUFFERING Enum 30/0x1E Description |