diff options
Diffstat (limited to 'Documentation')
36 files changed, 1139 insertions, 369 deletions
diff --git a/Documentation/cciss.txt b/Documentation/cciss.txt index 68a711fb82c..15378422fc4 100644 --- a/Documentation/cciss.txt +++ b/Documentation/cciss.txt @@ -133,3 +133,32 @@ hardware and it is important to prevent the kernel from attempting to directly access these devices too, as if the array controller were merely a SCSI controller in the same way that we are allowing it to access SCSI tape drives. +SCSI error handling for tape drives and medium changers +------------------------------------------------------- + +The linux SCSI mid layer provides an error handling protocol which +kicks into gear whenever a SCSI command fails to complete within a +certain amount of time (which can vary depending on the command). +The cciss driver participates in this protocol to some extent. The +normal protocol is a four step process. First the device is told +to abort the command. If that doesn't work, the device is reset. +If that doesn't work, the SCSI bus is reset. If that doesn't work +the host bus adapter is reset. Because the cciss driver is a block +driver as well as a SCSI driver and only the tape drives and medium +changers are presented to the SCSI mid layer, and unlike more +straightforward SCSI drivers, disk i/o continues through the block +side during the SCSI error recovery process, the cciss driver only +implements the first two of these actions, aborting the command, and +resetting the device. Additionally, most tape drives will not oblige +in aborting commands, and sometimes it appears they will not even +obey a reset coommand, though in most circumstances they will. In +the case that the command cannot be aborted and the device cannot be +reset, the device will be set offline. + +In the event the error handling code is triggered and a tape drive is +successfully reset or the tardy command is successfully aborted, the +tape drive may still not allow i/o to continue until some command +is issued which positions the tape to a known position. Typically you +must rewind the tape (by issuing "mt -f /dev/st0 rewind" for example) +before i/o can proceed again to a tape drive which was reset. + diff --git a/Documentation/dvb/bt8xx.txt b/Documentation/dvb/bt8xx.txt index cb63b7a93c8..df6c05453cb 100644 --- a/Documentation/dvb/bt8xx.txt +++ b/Documentation/dvb/bt8xx.txt @@ -1,5 +1,5 @@ -How to get the Nebula, PCTV and Twinhan DST cards working -========================================================= +How to get the Nebula, PCTV, FusionHDTV Lite and Twinhan DST cards working +========================================================================== This class of cards has a bt878a as the PCI interface, and require the bttv driver. @@ -26,27 +26,31 @@ Furthermore you need to enable In general you need to load the bttv driver, which will handle the gpio and i2c communication for us, plus the common dvb-bt8xx device driver. -The frontends for Nebula (nxt6000), Pinnacle PCTV (cx24110) and -TwinHan (dst) are loaded automatically by the dvb-bt8xx device driver. +The frontends for Nebula (nxt6000), Pinnacle PCTV (cx24110), TwinHan (dst), +FusionHDTV DVB-T Lite (mt352) and FusionHDTV5 Lite (lgdt330x) are loaded +automatically by the dvb-bt8xx device driver. -3a) Nebula / Pinnacle PCTV --------------------------- +3a) Nebula / Pinnacle PCTV / FusionHDTV Lite +--------------------------------------------- $ modprobe bttv (normally bttv is being loaded automatically by kmod) - $ modprobe dvb-bt8xx (or just place dvb-bt8xx in /etc/modules for automatic loading) + $ modprobe dvb-bt8xx + +(or just place dvb-bt8xx in /etc/modules for automatic loading) 3b) TwinHan and Clones -------------------------- - $ modprobe bttv i2c_hw=1 card=0x71 + $ modprobe bttv card=0x71 $ modprobe dvb-bt8xx $ modprobe dst The value 0x71 will override the PCI type detection for dvb-bt8xx, -which is necessary for TwinHan cards. +which is necessary for TwinHan cards. Omission of this parameter might result +in a system lockup. -If you're having an older card (blue color circuit) and card=0x71 locks +If you're having an older card (blue color PCB) and card=0x71 locks up your machine, try using 0x68, too. If that does not work, ask on the mailing list. @@ -64,11 +68,47 @@ verbose=0 means complete disabling of messages dst_addons takes values 0 and 0x20. A value of 0 means it is a FTA card. 0x20 means it has a Conditional Access slot. -The autodected values are determined bythe cards 'response -string' which you can see in your logs e.g. +The autodetected values are determined by the cards 'response string' +which you can see in your logs e.g. dst_get_device_id: Recognise [DSTMCI] +If you need to sent in bug reports on the dst, please do send in a complete +log with the verbose=4 module parameter. For general usage, the default setting +of verbose=1 is ideal. + + +4) Multiple cards +-------------------------- + +If you happen to be running multiple cards, it would be advisable to load +the bttv module with the card id. This would help to solve any module loading +problems that you might face. + +For example, if you have a Twinhan and Clones card along with a FusionHDTV5 Lite + + $ modprobe bttv card=0x71 card=0x87 + +Here the order of the card id is important and should be the same as that of the +physical order of the cards. Here card=0x71 represents the Twinhan and clones +and card=0x87 represents Fusion HDTV5 Lite. These arguments can also be +specified in decimal, rather than hex: + + $ modprobe bttv card=113 card=135 + +Some examples of card-id's + +Pinnacle Sat 0x5e (94) +Nebula Digi TV 0x68 (104) +PC HDTV 0x70 (112) +Twinhan 0x71 (113) +FusionHDTV DVB-T Lite 0x80 (128) +FusionHDTV5 Lite 0x87 (135) + +For a full list of card-id's, see the V4L Documentation within the kernel +source: linux/Documentation/video4linux/CARDLIST.bttv + +If you have problems with this please do ask on the mailing list. -- Authors: Richard Walker, Jamie Honan, Michael Hunold, Manu Abraham diff --git a/Documentation/dvb/cards.txt b/Documentation/dvb/cards.txt index efdc4ee9d40..19329cf7b09 100644 --- a/Documentation/dvb/cards.txt +++ b/Documentation/dvb/cards.txt @@ -41,6 +41,12 @@ o Frontends drivers: - dib3000mb : DiBcom 3000-MB demodulator DVB-S/C/T: - dst : TwinHan DST Frontend + ATSC: + - nxt200x : Nxtwave NXT2002 & NXT2004 + - or51211 : or51211 based (pcHDTV HD2000 card) + - or51132 : or51132 based (pcHDTV HD3000 card) + - bcm3510 : Broadcom BCM3510 + - lgdt330x : LG Electronics DT3302 & DT3303 o Cards based on the Phillips saa7146 multimedia PCI bridge chip: @@ -62,6 +68,10 @@ o Cards based on the Conexant Bt8xx PCI bridge: - Nebula Electronics DigiTV - TwinHan DST - Avermedia DVB-T + - ChainTech digitop DST-1000 DVB-S + - pcHDTV HD-2000 TV + - DViCO FusionHDTV DVB-T Lite + - DViCO FusionHDTV5 Lite o Technotrend / Hauppauge DVB USB devices: - Nova USB @@ -83,3 +93,30 @@ o DiBcom DVB-T USB based devices: - DiBcom USB2.0 DVB-T reference device (non-public) o Experimental support for the analog module of the Siemens DVB-C PCI card + +o Cards based on the Conexant cx2388x PCI bridge: + - ADS Tech Instant TV DVB-T PCI + - ATI HDTV Wonder + - digitalnow DNTV Live! DVB-T + - DViCO FusionHDTV DVB-T1 + - DViCO FusionHDTV DVB-T Plus + - DViCO FusionHDTV3 Gold-Q + - DViCO FusionHDTV3 Gold-T + - DViCO FusionHDTV5 Gold + - Hauppauge Nova-T DVB-T + - KWorld/VStream XPert DVB-T + - pcHDTV HD3000 HDTV + - TerraTec Cinergy 1400 DVB-T + - WinFast DTV1000-T + +o Cards based on the Phillips saa7134 PCI bridge: + - Medion 7134 + - Pinnacle PCTV 300i DVB-T + PAL + - LifeView FlyDVB-T DUO + - Typhoon DVB-T Duo Digital/Analog Cardbus + - Philips TOUGH DVB-T reference design + - Philips EUROPA V3 reference design + - Compro Videomate DVB-T300 + - Compro Videomate DVB-T200 + - AVerMedia AVerTVHD MCE A180 + diff --git a/Documentation/dvb/contributors.txt b/Documentation/dvb/contributors.txt index c9d5ce37070..2cbd2d0f6fd 100644 --- a/Documentation/dvb/contributors.txt +++ b/Documentation/dvb/contributors.txt @@ -75,5 +75,22 @@ Ernst Peinlich <e.peinlich@inode.at> Peter Beutner <p.beutner@gmx.net> for the IR code for the ttusb-dec driver +Wilson Michaels <wilsonmichaels@earthlink.net> + for the lgdt330x frontend driver, and various bugfixes + +Michael Krufky <mkrufky@m1k.net> + for maintaining v4l/dvb inter-tree dependencies + +Taylor Jacob <rtjacob@earthlink.net> + for the nxt2002 frontend driver + +Jean-Francois Thibert <jeanfrancois@sagetv.com> + for the nxt2004 frontend driver + +Kirk Lapray <kirk.lapray@gmail.com> + for the or51211 and or51132 frontend drivers, and + for merging the nxt2002 and nxt2004 modules into a + single nxt200x frontend driver. + (If you think you should be in this list, but you are not, drop a line to the DVB mailing list) diff --git a/Documentation/dvb/get_dvb_firmware b/Documentation/dvb/get_dvb_firmware index a750f0101d9..be6eb4c7599 100644 --- a/Documentation/dvb/get_dvb_firmware +++ b/Documentation/dvb/get_dvb_firmware @@ -22,7 +22,7 @@ use File::Temp qw/ tempdir /; use IO::Handle; @components = ( "sp8870", "sp887x", "tda10045", "tda10046", "av7110", "dec2000t", - "dec2540t", "dec3000s", "vp7041", "dibusb", "nxt2002", + "dec2540t", "dec3000s", "vp7041", "dibusb", "nxt2002", "nxt2004", "or51211", "or51132_qam", "or51132_vsb"); # Check args @@ -252,6 +252,23 @@ sub nxt2002 { $outfile; } +sub nxt2004 { + my $sourcefile = "AVerTVHD_MCE_A180_Drv_v1.2.2.16.zip"; + my $url = "http://www.aver.com/support/Drivers/$sourcefile"; + my $hash = "111cb885b1e009188346d72acfed024c"; + my $outfile = "dvb-fe-nxt2004.fw"; + my $tmpdir = tempdir(DIR => "/tmp", CLEANUP => 1); + + checkstandard(); + + wgetfile($sourcefile, $url); + unzip($sourcefile, $tmpdir); + verify("$tmpdir/3xHybrid.sys", $hash); + extract("$tmpdir/3xHybrid.sys", 465304, 9584, $outfile); + + $outfile; +} + sub or51211 { my $fwfile = "dvb-fe-or51211.fw"; my $url = "http://linuxtv.org/downloads/firmware/$fwfile"; diff --git a/Documentation/early-userspace/README b/Documentation/early-userspace/README index 270a88e22fb..cddbac456c2 100644 --- a/Documentation/early-userspace/README +++ b/Documentation/early-userspace/README @@ -28,7 +28,7 @@ the image from specifications. CPIO ARCHIVE method You can create a cpio archive that contains the early userspace image. -Youre cpio archive should be specified in CONFIG_INITRAMFS_SOURCE and it +Your cpio archive should be specified in CONFIG_INITRAMFS_SOURCE and it will be used directly. Only a single cpio file may be specified in CONFIG_INITRAMFS_SOURCE and directory and file names are not allowed in combination with a cpio archive. diff --git a/Documentation/fb/fbcon.txt b/Documentation/fb/fbcon.txt new file mode 100644 index 00000000000..08dce0f631b --- /dev/null +++ b/Documentation/fb/fbcon.txt @@ -0,0 +1,152 @@ +The Framebuffer Console +======================= + + The framebuffer console (fbcon), as its name implies, is a text +console running on top of the framebuffer device. It has the functionality of +any standard text console driver, such as the VGA console, with the added +features that can be attributed to the graphical nature of the framebuffer. + + In the x86 architecture, the framebuffer console is optional, and +some even treat it as a toy. For other architectures, it is the only available +display device, text or graphical. + + What are the features of fbcon? The framebuffer console supports +high resolutions, varying font types, display rotation, primitive multihead, +etc. Theoretically, multi-colored fonts, blending, aliasing, and any feature +made available by the underlying graphics card are also possible. + +A. Configuration + + The framebuffer console can be enabled by using your favorite kernel +configuration tool. It is under Device Drivers->Graphics Support->Support for +framebuffer devices->Framebuffer Console Support. Select 'y' to compile +support statically, or 'm' for module support. The module will be fbcon. + + In order for fbcon to activate, at least one framebuffer driver is +required, so choose from any of the numerous drivers available. For x86 +systems, they almost universally have VGA cards, so vga16fb and vesafb will +always be available. However, using a chipset-specific driver will give you +more speed and features, such as the ability to change the video mode +dynamically. + + To display the penguin logo, choose any logo available in Logo +Configuration->Boot up logo. + + Also, you will need to select at least one compiled-in fonts, but if +you don't do anything, the kernel configuration tool will select one for you, +usually an 8x16 font. + +GOTCHA: A common bug report is enabling the framebuffer without enabling the +framebuffer console. Depending on the driver, you may get a blanked or +garbled display, but the system still boots to completion. If you are +fortunate to have a driver that does not alter the graphics chip, then you +will still get a VGA console. + +B. Loading + +Possible scenarios: + +1. Driver and fbcon are compiled statically + + Usually, fbcon will automatically take over your console. The notable + exception is vesafb. It needs to be explicitly activated with the + vga= boot option parameter. + +2. Driver is compiled statically, fbcon is compiled as a module + + Depending on the driver, you either get a standard console, or a + garbled display, as mentioned above. To get a framebuffer console, + do a 'modprobe fbcon'. + +3. Driver is compiled as a module, fbcon is compiled statically + + You get your standard console. Once the driver is loaded with + 'modprobe xxxfb', fbcon automatically takes over the console with + the possible exception of using the fbcon=map:n option. See below. + +4. Driver and fbcon are compiled as a module. + + You can load them in any order. Once both are loaded, fbcon will take + over the console. + +C. Boot options + + The framebuffer console has several, largely unknown, boot options + that can change its behavior. + +1. fbcon=font:<name> + + Select the initial font to use. The value 'name' can be any of the + compiled-in fonts: VGA8x16, 7x14, 10x18, VGA8x8, MINI4x6, RomanLarge, + SUN8x16, SUN12x22, ProFont6x11, Acorn8x8, PEARL8x8. + + Note, not all drivers can handle font with widths not divisible by 8, + such as vga16fb. + +2. fbcon=scrollback:<value>[k] + + The scrollback buffer is memory that is used to preserve display + contents that has already scrolled past your view. This is accessed + by using the Shift-PageUp key combination. The value 'value' is any + integer. It defaults to 32KB. The 'k' suffix is optional, and will + multiply the 'value' by 1024. + +3. fbcon=map:<0123> + + This is an interesting option. It tells which driver gets mapped to + which console. The value '0123' is a sequence that gets repeated until + the total length is 64 which is the number of consoles available. In + the above example, it is expanded to 012301230123... and the mapping + will be: + + tty | 1 2 3 4 5 6 7 8 9 ... + fb | 0 1 2 3 0 1 2 3 0 ... + + ('cat /proc/fb' should tell you what the fb numbers are) + + One side effect that may be useful is using a map value that exceeds + the number of loaded fb drivers. For example, if only one driver is + available, fb0, adding fbcon=map:1 tells fbcon not to take over the + console. + + Later on, when you want to map the console the to the framebuffer + device, you can use the con2fbmap utility. + +4. fbcon=vc:<n1>-<n2> + + This option tells fbcon to take over only a range of consoles as + specified by the values 'n1' and 'n2'. The rest of the consoles + outside the given range will still be controlled by the standard + console driver. + + NOTE: For x86 machines, the standard console is the VGA console which + is typically located on the same video card. Thus, the consoles that + are controlled by the VGA console will be garbled. + +4. fbcon=rotate:<n> + + This option changes the orientation angle of the console display. The + value 'n' accepts the following: + + 0 - normal orientation (0 degree) + 1 - clockwise orientation (90 degrees) + 2 - upside down orientation (180 degrees) + 3 - counterclockwise orientation (270 degrees) + + The angle can be changed anytime afterwards by 'echoing' the same + numbers to any one of the 2 attributes found in + /sys/class/graphics/fb{x} + + con_rotate - rotate the display of the active console + con_rotate_all - rotate the display of all consoles + + Console rotation will only become available if Console Rotation + Support is compiled in your kernel. + + NOTE: This is purely console rotation. Any other applications that + use the framebuffer will remain at their 'normal'orientation. + Actually, the underlying fb driver is totally ignorant of console + rotation. + +--- +Antonino Daplas <adaplas@pol.net> diff --git a/Documentation/feature-removal-schedule.txt b/Documentation/feature-removal-schedule.txt index decdf9917e0..429db4bf98e 100644 --- a/Documentation/feature-removal-schedule.txt +++ b/Documentation/feature-removal-schedule.txt @@ -25,6 +25,13 @@ Who: Adrian Bunk <bunk@stusta.de> --------------------------- +What: drivers depending on OBSOLETE_OSS_DRIVER +When: January 2006 +Why: OSS drivers with ALSA replacements +Who: Adrian Bunk <bunk@stusta.de> + +--------------------------- + What: RCU API moves to EXPORT_SYMBOL_GPL When: April 2006 Files: include/linux/rcupdate.h, kernel/rcupdate.c @@ -60,6 +67,21 @@ Who: Jody McIntyre <scjody@steamballoon.com> --------------------------- +What: Video4Linux API 1 ioctls and video_decoder.h from Video devices. +When: July 2006 +Why: V4L1 AP1 was replaced by V4L2 API. during migration from 2.4 to 2.6 + series. The old API have lots of drawbacks and don't provide enough + means to work with all video and audio standards. The newer API is + already available on the main drivers and should be used instead. + Newer drivers should use v4l_compat_translate_ioctl function to handle + old calls, replacing to newer ones. + Decoder iocts are using internally to allow video drivers to + communicate with video decoders. This should also be improved to allow + V4L2 calls being translated into compatible internal ioctls. +Who: Mauro Carvalho Chehab <mchehab@brturbo.com.br> + +--------------------------- + What: i2c sysfs name change: in1_ref, vid deprecated in favour of cpu0_vid When: November 2005 Files: drivers/i2c/chips/adm1025.c, drivers/i2c/chips/adm1026.c @@ -111,3 +133,10 @@ Why: This interface has been obsoleted by the new layer3-independent to link against API-compatible library on top of libnfnetlink_queue instead of the current 'libipq'. Who: Harald Welte <laforge@netfilter.org> + +--------------------------- + +What: EXPORT_SYMBOL(lookup_hash) +When: January 2006 +Why: Too low-level interface. Use lookup_one_len or lookup_create instead. +Who: Christoph Hellwig <hch@lst.de> diff --git a/Documentation/filesystems/ext2.txt b/Documentation/filesystems/ext2.txt index d16334ec48b..a8edb376b04 100644 --- a/Documentation/filesystems/ext2.txt +++ b/Documentation/filesystems/ext2.txt @@ -17,8 +17,6 @@ set using tune2fs(8). Kernel-determined defaults are indicated by (*). bsddf (*) Makes `df' act like BSD. minixdf Makes `df' act like Minix. -check Check block and inode bitmaps at mount time - (requires CONFIG_EXT2_CHECK). check=none, nocheck (*) Don't do extra checking of bitmaps on mount (check=normal and check=strict options removed) diff --git a/Documentation/i2c/busses/i2c-viapro b/Documentation/i2c/busses/i2c-viapro index 9363b8bd610..16775663b9f 100644 --- a/Documentation/i2c/busses/i2c-viapro +++ b/Documentation/i2c/busses/i2c-viapro @@ -7,12 +7,10 @@ Supported adapters: * VIA Technologies, Inc. VT82C686A/B Datasheet: Sometimes available at the VIA website - * VIA Technologies, Inc. VT8231, VT8233, VT8233A, VT8235, VT8237 - Datasheet: available on request from Via + * VIA Technologies, Inc. VT8231, VT8233, VT8233A, VT8235, VT8237R + Datasheet: available on request from VIA Authors: - Frodo Looijaard <frodol@dds.nl>, - Philip Edelbrock <phil@netroedge.com>, Kyösti Mälkki <kmalkki@cc.hut.fi>, Mark D. Studebaker <mdsxyz123@yahoo.com>, Jean Delvare <khali@linux-fr.org> diff --git a/Documentation/i2c/writing-clients b/Documentation/i2c/writing-clients index cff7b652588..d19993cc060 100644 --- a/Documentation/i2c/writing-clients +++ b/Documentation/i2c/writing-clients @@ -412,7 +412,7 @@ For now, you can ignore the `flags' parameter. It is there for future use. release_region(address,FOO_EXTENT); /* SENSORS ONLY END */ ERROR1: - kfree(new_client); + kfree(data); ERROR0: return err; } @@ -443,7 +443,7 @@ much simpler than the attachment code, fortunately! release_region(client->addr,LM78_EXTENT); /* HYBRID SENSORS CHIP ONLY END */ - kfree(data); + kfree(i2c_get_clientdata(client)); return 0; } diff --git a/Documentation/md.txt b/Documentation/md.txt index e2b536992a2..23e6cce40f9 100644 --- a/Documentation/md.txt +++ b/Documentation/md.txt @@ -116,3 +116,122 @@ and it's role in the array. Once started with RUN_ARRAY, uninitialized spares can be added with HOT_ADD_DISK. + + + +MD devices in sysfs +------------------- +md devices appear in sysfs (/sys) as regular block devices, +e.g. + /sys/block/md0 + +Each 'md' device will contain a subdirectory called 'md' which +contains further md-specific information about the device. + +All md devices contain: + level + a text file indicating the 'raid level'. This may be a standard + numerical level prefixed by "RAID-" - e.g. "RAID-5", or some + other name such as "linear" or "multipath". + If no raid level has been set yet (array is still being + assembled), this file will be empty. + + raid_disks + a text file with a simple number indicating the number of devices + in a fully functional array. If this is not yet known, the file + will be empty. If an array is being resized (not currently + possible) this will contain the larger of the old and new sizes. + +As component devices are added to an md array, they appear in the 'md' +directory as new directories named + dev-XXX +where XXX is a name that the kernel knows for the device, e.g. hdb1. +Each directory contains: + + block + a symlink to the block device in /sys/block, e.g. + /sys/block/md0/md/dev-hdb1/block -> ../../../../block/hdb/hdb1 + + super + A file containing an image of the superblock read from, or + written to, that device. + + state + A file recording the current state of the device in the array + which can be a comma separated list of + faulty - device has been kicked from active use due to + a detected fault + in_sync - device is a fully in-sync member of the array + spare - device is working, but not a full member. + This includes spares that are in the process + of being recoverred to + This list make grow in future. + + +An active md device will also contain and entry for each active device +in the array. These are named + + rdNN + +where 'NN' is the possition in the array, starting from 0. +So for a 3 drive array there will be rd0, rd1, rd2. +These are symbolic links to the appropriate 'dev-XXX' entry. +Thus, for example, + cat /sys/block/md*/md/rd*/state +will show 'in_sync' on every line. + + + +Active md devices for levels that support data redundancy (1,4,5,6) +also have + + sync_action + a text file that can be used to monitor and control the rebuild + process. It contains one word which can be one of: + resync - redundancy is being recalculated after unclean + shutdown or creation + recover - a hot spare is being built to replace a + failed/missing device + idle - nothing is happening + check - A full check of redundancy was requested and is + happening. This reads all block and checks + them. A repair may also happen for some raid + levels. + repair - A full check and repair is happening. This is + similar to 'resync', but was requested by the + user, and the write-intent bitmap is NOT used to + optimise the process. + + This file is writable, and each of the strings that could be + read are meaningful for writing. + + 'idle' will stop an active resync/recovery etc. There is no + guarantee that another resync/recovery may not be automatically + started again, though some event will be needed to trigger + this. + 'resync' or 'recovery' can be used to restart the + corresponding operation if it was stopped with 'idle'. + 'check' and 'repair' will start the appropriate process + providing the current state is 'idle'. + + mismatch_count + When performing 'check' and 'repair', and possibly when + performing 'resync', md will count the number of errors that are + found. The count in 'mismatch_cnt' is the number of sectors + that were re-written, or (for 'check') would have been + re-written. As most raid levels work in units of pages rather + than sectors, this my be larger than the number of actual errors + by a factor of the number of sectors in a page. + +Each active md device may also have attributes specific to the +personality module that manages it. +These are specific to the implementation of the module and could +change substantially if the implementation changes. + +These currently include + + stripe_cache_size (currently raid5 only) + number of entries in the stripe cache. This is writable, but + there are upper and lower limits (32768, 16). Default is 128. + strip_cache_active (currently raid5 only) + number of active entries in the stripe cache diff --git a/Documentation/networking/README.ipw2100 b/Documentation/networking/README.ipw2100 index 2046948b020..3ab40379d1c 100644 --- a/Documentation/networking/README.ipw2100 +++ b/Documentation/networking/README.ipw2100 @@ -1,27 +1,82 @@ -=========================== -Intel(R) PRO/Wireless 2100 Network Connection Driver for Linux +Intel(R) PRO/Wireless 2100 Driver for Linux in support of: + +Intel(R) PRO/Wireless 2100 Network Connection + +Copyright (C) 2003-2005, Intel Corporation + README.ipw2100 -March 14, 2005 +Version: 1.1.3 +Date : October 17, 2005 -=========================== Index ---------------------------- -0. Introduction -1. Release 1.1.0 Current Features -2. Command Line Parameters -3. Sysfs Helper Files -4. Radio Kill Switch -5. Dynamic Firmware -6. Power Management -7. Support -8. License - - -=========================== -0. Introduction ------------- ----- ----- ---- --- -- - +----------------------------------------------- +0. IMPORTANT INFORMATION BEFORE USING THIS DRIVER +1. Introduction +2. Release 1.1.3 Current Features +3. Command Line Parameters +4. Sysfs Helper Files +5. Radio Kill Switch +6. Dynamic Firmware +7. Power Management +8. Support +9. License + + +0. IMPORTANT INFORMATION BEFORE USING THIS DRIVER +----------------------------------------------- + +Important Notice FOR ALL USERS OR DISTRIBUTORS!!!! + +Intel wireless LAN adapters are engineered, manufactured, tested, and +quality checked to ensure that they meet all necessary local and +governmental regulatory agency requirements for the regions that they +are designated and/or marked to ship into. Since wireless LANs are +generally unlicensed devices that share spectrum with radars, +satellites, and other licensed and unlicensed devices, it is sometimes +necessary to dynamically detect, avoid, and limit usage to avoid +interference with these devices. In many instances Intel is required to +provide test data to prove regional and local compliance to regional and +governmental regulations before certification or approval to use the +product is granted. Intel's wireless LAN's EEPROM, firmware, and +software driver are designed to carefully control parameters that affect +radio operation and to ensure electromagnetic compliance (EMC). These +parameters include, without limitation, RF power, spectrum usage, +channel scanning, and human exposure. + +For these reasons Intel cannot permit any manipulation by third parties +of the software provided in binary format with the wireless WLAN +adapters (e.g., the EEPROM and firmware). Furthermore, if you use any +patches, utilities, or code with the Intel wireless LAN adapters that +have been manipulated by an unauthorized party (i.e., patches, +utilities, or code (including open source code modifications) which have +not been validated by Intel), (i) you will be solely responsible for +ensuring the regulatory compliance of the products, (ii) Intel will bear +no liability, under any theory of liability for any issues associated +with the modified products, including without limitation, claims under +the warranty and/or issues arising from regulatory non-compliance, and +(iii) Intel will not provide or be required to assist in providing +support to any third parties for such modified products. + +Note: Many regulatory agencies consider Wireless LAN adapters to be +modules, and accordingly, condition system-level regulatory approval +upon receipt and review of test data documenting that the antennas and +system configuration do not cause the EMC and radio operation to be +non-compliant. + +The drivers available for download from SourceForge are provided as a +part of a development project. Conformance to local regulatory +requirements is the responsibility of the individual developer. As +such, if you are interested in deploying or shipping a driver as part of +solution intended to be used for purposes other than development, please +obtain a tested driver from Intel Customer Support at: + +http://support.intel.com/support/notebook/sb/CS-006408.htm + + +1. Introduction +----------------------------------------------- This document provides a brief overview of the features supported by the IPW2100 driver project. The main project website, where the latest @@ -34,9 +89,8 @@ potential fixes and patches, as well as links to the development mailing list for the driver project. -=========================== -1. Release 1.1.0 Current Supported Features ---------------------------- +2. Release 1.1.3 Current Supported Features +----------------------------------------------- - Managed (BSS) and Ad-Hoc (IBSS) - WEP (shared key and open) - Wireless Tools support @@ -51,9 +105,8 @@ on the amount of validation and interoperability testing that has been performed on a given feature. -=========================== -2. Command Line Parameters ---------------------------- +3. Command Line Parameters +----------------------------------------------- If the driver is built as a module, the following optional parameters are used by entering them on the command line with the modprobe command using this @@ -75,9 +128,9 @@ associate boolean associate=0 /* Do NOT auto associate */ disable boolean disable=1 /* Do not power the HW */ -=========================== -3. Sysfs Helper Files +4. Sysfs Helper Files --------------------------- +----------------------------------------------- There are several ways to control the behavior of the driver. Many of the general capabilities are exposed through the Wireless Tools (iwconfig). There @@ -120,9 +173,8 @@ For the device level files, see /sys/bus/pci/drivers/ipw2100: based RF kill from ON -> OFF -> ON, the radio will NOT come back on -=========================== -4. Radio Kill Switch ---------------------------- +5. Radio Kill Switch +----------------------------------------------- Most laptops provide the ability for the user to physically disable the radio. Some vendors have implemented this as a physical switch that requires no software to turn the radio off and on. On other laptops, however, the switch @@ -134,9 +186,8 @@ See the Sysfs helper file 'rf_kill' for determining the state of the RF switch on your system. -=========================== -5. Dynamic Firmware ---------------------------- +6. Dynamic Firmware +----------------------------------------------- As the firmware is licensed under a restricted use license, it can not be included within the kernel sources. To enable the IPW2100 you will need a firmware image to load into the wireless NIC's processors. @@ -146,9 +197,8 @@ You can obtain these images from <http://ipw2100.sf.net/firmware.php>. See INSTALL for instructions on installing the firmware. -=========================== -6. Power Management ---------------------------- +7. Power Management +----------------------------------------------- The IPW2100 supports the configuration of the Power Save Protocol through a private wireless extension interface. The IPW2100 supports the following different modes: @@ -200,9 +250,8 @@ xxxx/yyyy will be replaced with 'off' -- the level reported will be the active level if `iwconfig eth1 power on` is invoked. -=========================== -7. Support ---------------------------- +8. Support +----------------------------------------------- For general development information and support, go to: @@ -218,9 +267,8 @@ For installation support on the ipw2100 1.1.0 driver on Linux kernels http://supportmail.intel.com -=========================== -8. License ---------------------------- +9. License +----------------------------------------------- Copyright(c) 2003 - 2005 Intel Corporation. All rights reserved. diff --git a/Documentation/networking/README.ipw2200 b/Documentation/networking/README.ipw2200 index 6916080c5f0..c6492d3839f 100644 --- a/Documentation/networking/README.ipw2200 +++ b/Documentation/networking/README.ipw2200 @@ -1,33 +1,89 @@ Intel(R) PRO/Wireless 2915ABG Driver for Linux in support of: -Intel(R) PRO/Wireless 2200BG Network Connection -Intel(R) PRO/Wireless 2915ABG Network Connection +Intel(R) PRO/Wireless 2200BG Network Connection +Intel(R) PRO/Wireless 2915ABG Network Connection -Note: The Intel(R) PRO/Wireless 2915ABG Driver for Linux and Intel(R) -PRO/Wireless 2200BG Driver for Linux is a unified driver that works on -both hardware adapters listed above. In this document the Intel(R) -PRO/Wireless 2915ABG Driver for Linux will be used to reference the +Note: The Intel(R) PRO/Wireless 2915ABG Driver for Linux and Intel(R) +PRO/Wireless 2200BG Driver for Linux is a unified driver that works on +both hardware adapters listed above. In this document the Intel(R) +PRO/Wireless 2915ABG Driver for Linux will be used to reference the unified driver. Copyright (C) 2004-2005, Intel Corporation README.ipw2200 -Version: 1.0.0 -Date : January 31, 2005 +Version: 1.0.8 +Date : October 20, 2005 Index ----------------------------------------------- +0. IMPORTANT INFORMATION BEFORE USING THIS DRIVER 1. Introduction 1.1. Overview of features 1.2. Module parameters 1.3. Wireless Extension Private Methods 1.4. Sysfs Helper Files -2. About the Version Numbers -3. Support -4. License +2. Ad-Hoc Networking +3. Interacting with Wireless Tools +3.1. iwconfig mode +4. About the Version Numbers +5. Firmware installation +6. Support +7. License + + +0. IMPORTANT INFORMATION BEFORE USING THIS DRIVER +----------------------------------------------- + +Important Notice FOR ALL USERS OR DISTRIBUTORS!!!! + +Intel wireless LAN adapters are engineered, manufactured, tested, and +quality checked to ensure that they meet all necessary local and +governmental regulatory agency requirements for the regions that they +are designated and/or marked to ship into. Since wireless LANs are +generally unlicensed devices that share spectrum with radars, +satellites, and other licensed and unlicensed devices, it is sometimes +necessary to dynamically detect, avoid, and limit usage to avoid +interference with these devices. In many instances Intel is required to +provide test data to prove regional and local compliance to regional and +governmental regulations before certification or approval to use the +product is granted. Intel's wireless LAN's EEPROM, firmware, and +software driver are designed to carefully control parameters that affect +radio operation and to ensure electromagnetic compliance (EMC). These +parameters include, without limitation, RF power, spectrum usage, +channel scanning, and human exposure. + +For these reasons Intel cannot permit any manipulation by third parties +of the software provided in binary format with the wireless WLAN +adapters (e.g., the EEPROM and firmware). Furthermore, if you use any +patches, utilities, or code with the Intel wireless LAN adapters that +have been manipulated by an unauthorized party (i.e., patches, +utilities, or code (including open source code modifications) which have +not been validated by Intel), (i) you will be solely responsible for +ensuring the regulatory compliance of the products, (ii) Intel will bear +no liability, under any theory of liability for any issues associated +with the modified products, including without limitation, claims under +the warranty and/or issues arising from regulatory non-compliance, and +(iii) Intel will not provide or be required to assist in providing +support to any third parties for such modified products. + +Note: Many regulatory agencies consider Wireless LAN adapters to be +modules, and accordingly, condition system-level regulatory approval +upon receipt and review of test data documenting that the antennas and +system configuration do not cause the EMC and radio operation to be +non-compliant. + +The drivers available for download from SourceForge are provided as a +part of a development project. Conformance to local regulatory +requirements is the responsibility of the individual developer. As +such, if you are interested in deploying or shipping a driver as part of +solution intended to be used for purposes other than development, please +obtain a tested driver from Intel Customer Support at: + +http://support.intel.com/support/notebook/sb/CS-006408.htm 1. Introduction @@ -45,7 +101,7 @@ file. 1.1. Overview of Features ----------------------------------------------- -The current release (1.0.0) supports the following features: +The current release (1.0.8) supports the following features: + BSS mode (Infrastructure, Managed) + IBSS mode (Ad-Hoc) @@ -56,17 +112,27 @@ The current release (1.0.0) supports the following features: + Full A rate support (2915 only) + Transmit power control + S state support (ACPI suspend/resume) + +The following features are currently enabled, but not officially +supported: + ++ WPA + long/short preamble support ++ Monitor mode (aka RFMon) + +The distinction between officially supported and enabled is a reflection +on the amount of validation and interoperability testing that has been +performed on a given feature. 1.2. Command Line Parameters ----------------------------------------------- -Like many modules used in the Linux kernel, the Intel(R) PRO/Wireless -2915ABG Driver for Linux allows certain configuration options to be -provided as module parameters. The most common way to specify a module -parameter is via the command line. +Like many modules used in the Linux kernel, the Intel(R) PRO/Wireless +2915ABG Driver for Linux allows configuration options to be provided +as module parameters. The most common way to specify a module parameter +is via the command line. The general form is: @@ -96,14 +162,18 @@ Where the supported parameter are: debug If using a debug build, this is used to control the amount of debug - info is logged. See the 'dval' and 'load' script for more info on - how to use this (the dval and load scripts are provided as part + info is logged. See the 'dvals' and 'load' script for more info on + how to use this (the dvals and load scripts are provided as part of the ipw2200 development snapshot releases available from the SourceForge project at http://ipw2200.sf.net) + + led + Can be used to turn on experimental LED code. + 0 = Off, 1 = On. Default is 0. mode Can be used to set the default mode of the adapter. - 0 = Managed, 1 = Ad-Hoc + 0 = Managed, 1 = Ad-Hoc, 2 = Monitor 1.3. Wireless Extension Private Methods @@ -164,8 +234,8 @@ The supported private methods are: ----------------------------------------------- The Linux kernel provides a pseudo file system that can be used to -access various components of the operating system. The Intel(R) -PRO/Wireless 2915ABG Driver for Linux exposes several configuration +access various components of the operating system. The Intel(R) +PRO/Wireless 2915ABG Driver for Linux exposes several configuration parameters through this mechanism. An entry in the sysfs can support reading and/or writing. You can @@ -184,13 +254,13 @@ You can set the debug level via: Where $VALUE would be a number in the case of this sysfs entry. The input to sysfs files does not have to be a number. For example, the -firmware loader used by hotplug utilizes sysfs entries for transferring +firmware loader used by hotplug utilizes sysfs entries for transfering the firmware image from user space into the driver. The Intel(R) PRO/Wireless 2915ABG Driver for Linux exposes sysfs entries -at two levels -- driver level, which apply to all instances of the -driver (in the event that there are more than one device installed) and -device level, which applies only to the single specific instance. +at two levels -- driver level, which apply to all instances of the driver +(in the event that there are more than one device installed) and device +level, which applies only to the single specific instance. 1.4.1 Driver Level Sysfs Helper Files @@ -203,6 +273,7 @@ For the driver level files, look in /sys/bus/pci/drivers/ipw2200/ This controls the same global as the 'debug' module parameter + 1.4.2 Device Level Sysfs Helper Files ----------------------------------------------- @@ -213,7 +284,7 @@ For the device level files, look in For example: /sys/bus/pci/drivers/ipw2200/0000:02:01.0 -For the device level files, see /sys/bus/pci/[drivers/ipw2200: +For the device level files, see /sys/bus/pci/drivers/ipw2200: rf_kill read - @@ -231,8 +302,59 @@ For the device level files, see /sys/bus/pci/[drivers/ipw2200: ucode read-only access to the ucode version number + led + read - + 0 = LED code disabled + 1 = LED code enabled + write - + 0 = Disable LED code + 1 = Enable LED code + + NOTE: The LED code has been reported to hang some systems when + running ifconfig and is therefore disabled by default. + + +2. Ad-Hoc Networking +----------------------------------------------- + +When using a device in an Ad-Hoc network, it is useful to understand the +sequence and requirements for the driver to be able to create, join, or +merge networks. + +The following attempts to provide enough information so that you can +have a consistent experience while using the driver as a member of an +Ad-Hoc network. + +2.1. Joining an Ad-Hoc Network +----------------------------------------------- + +The easiest way to get onto an Ad-Hoc network is to join one that +already exists. -2. About the Version Numbers +2.2. Creating an Ad-Hoc Network +----------------------------------------------- + +An Ad-Hoc networks is created using the syntax of the Wireless tool. + +For Example: +iwconfig eth1 mode ad-hoc essid testing channel 2 + +2.3. Merging Ad-Hoc Networks +----------------------------------------------- + + +3. Interaction with Wireless Tools +----------------------------------------------- + +3.1 iwconfig mode +----------------------------------------------- + +When configuring the mode of the adapter, all run-time configured parameters +are reset to the value used when the module was loaded. This includes +channels, rates, ESSID, etc. + + +4. About the Version Numbers ----------------------------------------------- Due to the nature of open source development projects, there are @@ -259,12 +381,23 @@ available as quickly as possible, unknown anomalies should be expected. The major version number will be incremented when significant changes are made to the driver. Currently, there are no major changes planned. +5. Firmware installation +---------------------------------------------- + +The driver requires a firmware image, download it and extract the +files under /lib/firmware (or wherever your hotplug's firmware.agent +will look for firmware files) + +The firmware can be downloaded from the following URL: -3. Support + http://ipw2200.sf.net/ + + +6. Support ----------------------------------------------- -For installation support of the 1.0.0 version, you can contact -http://supportmail.intel.com, or you can use the open source project +For direct support of the 1.0.0 version, you can contact +http://supportmail.intel.com, or you can use the open source project support. For general information and support, go to: @@ -272,7 +405,7 @@ For general information and support, go to: http://ipw2200.sf.net/ -4. License +7. License ----------------------------------------------- Copyright(c) 2003 - 2005 Intel Corporation. All rights reserved. @@ -297,4 +430,3 @@ For general information and support, go to: James P. Ketrenos <ipw2100-admin@linux.intel.com> Intel Corporation, 5200 N.E. Elam Young Parkway, Hillsboro, OR 97124-6497 - diff --git a/Documentation/networking/dccp.txt b/Documentation/networking/dccp.txt new file mode 100644 index 00000000000..c45daabd3bf --- /dev/null +++ b/Documentation/networking/dccp.txt @@ -0,0 +1,56 @@ +DCCP protocol +============ + +Last updated: 10 November 2005 + +Contents +======== + +- Introduction +- Missing features +- Socket options +- Notes + +Introduction +============ + +Datagram Congestion Control Protocol (DCCP) is an unreliable, connection +based protocol designed to solve issues present in UDP and TCP particularly +for real time and multimedia traffic. + +It has a base protocol and pluggable congestion control IDs (CCIDs). + +It is at draft RFC status and the homepage for DCCP as a protocol is at: + http://www.icir.org/kohler/dcp/ + +Missing features +================ + +The DCCP implementation does not currently have all the features that are in +the draft RFC. + +In particular the following are missing: +- CCID2 support +- feature negotiation + +When testing against other implementations it appears that elapsed time +options are not coded compliant to the specification. + +Socket options +============== + +DCCP_SOCKOPT_PACKET_SIZE is used for CCID3 to set default packet size for +calculations. + +DCCP_SOCKOPT_SERVICE sets the service. This is compulsory as per the +specification. If you don't set it you will get EPROTO. + +Notes +===== + +SELinux does not yet have support for DCCP. You will need to turn it off or +else you will get EACCES. + +DCCP does not travel through NAT successfully at present. This is because +the checksum covers the psuedo-header as per TCP and UDP. It should be +relatively trivial to add Linux NAT support for DCCP. diff --git a/Documentation/networking/ip-sysctl.txt b/Documentation/networking/ip-sysctl.txt index 65895bb5141..ebc09a159f6 100644 --- a/Documentation/networking/ip-sysctl.txt +++ b/Documentation/networking/ip-sysctl.txt @@ -78,6 +78,11 @@ inet_peer_gc_maxtime - INTEGER TCP variables: +tcp_abc - INTEGER + Controls Appropriate Byte Count defined in RFC3465. If set to + 0 then does congestion avoid once per ack. 1 is conservative + value, and 2 is more agressive. + tcp_syn_retries - INTEGER Number of times initial SYNs for an active TCP connection attempt will be retransmitted. Should not be higher than 255. Default value diff --git a/Documentation/s390/Debugging390.txt b/Documentation/s390/Debugging390.txt index adbfe620c06..844c03fe792 100644 --- a/Documentation/s390/Debugging390.txt +++ b/Documentation/s390/Debugging390.txt @@ -871,7 +871,7 @@ by playing with the --adjust-vma parameter to objdump. -extern inline void spin_lock(spinlock_t *lp) +static inline void spin_lock(spinlock_t *lp) { a0: 18 34 lr %r3,%r4 a2: a7 3a 03 bc ahi %r3,956 diff --git a/Documentation/sched-arch.txt b/Documentation/sched-arch.txt new file mode 100644 index 00000000000..941615a9769 --- /dev/null +++ b/Documentation/sched-arch.txt @@ -0,0 +1,89 @@ + CPU Scheduler implementation hints for architecture specific code + + Nick Piggin, 2005 + +Context switch +============== +1. Runqueue locking +By default, the switch_to arch function is called with the runqueue +locked. This is usually not a problem unless switch_to may need to +take the runqueue lock. This is usually due to a wake up operation in +the context switch. See include/asm-ia64/system.h for an example. + +To request the scheduler call switch_to with the runqueue unlocked, +you must `#define __ARCH_WANT_UNLOCKED_CTXSW` in a header file +(typically the one where switch_to is defined). + +Unlocked context switches introduce only a very minor performance +penalty to the core scheduler implementation in the CONFIG_SMP case. + +2. Interrupt status +By default, the switch_to arch function is called with interrupts +disabled. Interrupts may be enabled over the call if it is likely to +introduce a significant interrupt latency by adding the line +`#define __ARCH_WANT_INTERRUPTS_ON_CTXSW` in the same place as for +unlocked context switches. This define also implies +`__ARCH_WANT_UNLOCKED_CTXSW`. See include/asm-arm/system.h for an +example. + + +CPU idle +======== +Your cpu_idle routines need to obey the following rules: + +1. Preempt should now disabled over idle routines. Should only + be enabled to call schedule() then disabled again. + +2. need_resched/TIF_NEED_RESCHED is only ever set, and will never + be cleared until the running task has called schedule(). Idle + threads need only ever query need_resched, and may never set or + clear it. + +3. When cpu_idle finds (need_resched() == 'true'), it should call + schedule(). It should not call schedule() otherwise. + +4. The only time interrupts need to be disabled when checking + need_resched is if we are about to sleep the processor until + the next interrupt (this doesn't provide any protection of + need_resched, it prevents losing an interrupt). + + 4a. Common problem with this type of sleep appears to be: + local_irq_disable(); + if (!need_resched()) { + local_irq_enable(); + *** resched interrupt arrives here *** + __asm__("sleep until next interrupt"); + } + +5. TIF_POLLING_NRFLAG can be set by idle routines that do not + need an interrupt to wake them up when need_resched goes high. + In other words, they must be periodically polling need_resched, + although it may be reasonable to do some background work or enter + a low CPU priority. + + 5a. If TIF_POLLING_NRFLAG is set, and we do decide to enter + an interrupt sleep, it needs to be cleared then a memory + barrier issued (followed by a test of need_resched with + interrupts disabled, as explained in 3). + +arch/i386/kernel/process.c has examples of both polling and +sleeping idle functions. + + +Possible arch/ problems +======================= + +Possible arch problems I found (and either tried to fix or didn't): + +h8300 - Is such sleeping racy vs interrupts? (See #4a). + The H8/300 manual I found indicates yes, however disabling IRQs + over the sleep mean only NMIs can wake it up, so can't fix easily + without doing spin waiting. + +ia64 - is safe_halt call racy vs interrupts? (does it sleep?) (See #4a) + +sh64 - Is sleeping racy vs interrupts? (See #4a) + +sparc - IRQs on at this point(?), change local_irq_save to _disable. + - TODO: needs secondary CPUs to disable preempt (See #1) + diff --git a/Documentation/scsi/00-INDEX b/Documentation/scsi/00-INDEX index fef92ebf266..e7da8c3a255 100644 --- a/Documentation/scsi/00-INDEX +++ b/Documentation/scsi/00-INDEX @@ -52,8 +52,6 @@ ppa.txt - info on driver for IOmega zip drive qlogicfas.txt - info on driver for QLogic FASxxx based adapters -qlogicisp.txt - - info on driver for QLogic ISP 1020 based adapters scsi-generic.txt - info on the sg driver for generic (non-disk/CD/tape) SCSI devices. scsi.txt diff --git a/Documentation/scsi/qlogicfas.txt b/Documentation/scsi/qlogicfas.txt index 398f9916807..c211d827fef 100644 --- a/Documentation/scsi/qlogicfas.txt +++ b/Documentation/scsi/qlogicfas.txt @@ -11,8 +11,7 @@ Qlogic boards: * IQ-PCI-10 * IQ-PCI-D -is provided by the qlogicisp.c driver. Check README.qlogicisp for -details. +is provided by the qla1280 driver. Nor does it support the PCI-Basic, which is supported by the 'am53c974' driver. diff --git a/Documentation/scsi/qlogicisp.txt b/Documentation/scsi/qlogicisp.txt deleted file mode 100644 index 6920f6c76a9..00000000000 --- a/Documentation/scsi/qlogicisp.txt +++ /dev/null @@ -1,30 +0,0 @@ -Notes for the QLogic ISP1020 PCI SCSI Driver: - -This driver works well in practice, but does not support disconnect/ -reconnect, which makes using it with tape drives impractical. - -It should work for most host adaptors with the ISP1020 chip. The -QLogic Corporation produces several PCI SCSI adapters which should -work: - - * IQ-PCI - * IQ-PCI-10 - * IQ-PCI-D - -This driver may work with boards containing the ISP1020A or ISP1040A -chips, but that has not been tested. - -This driver will NOT work with: - - * ISA or VL Bus Qlogic cards (they use the 'qlogicfas' driver) - * PCI-basic (it uses the 'am53c974' driver) - -Much thanks to QLogic's tech support for providing the latest ISP1020 -firmware, and for taking the time to review my code. - -Erik Moe -ehm@cris.com - -Revised: -Michael A. Griffith -grif@cs.ucr.edu diff --git a/Documentation/scsi/scsi_eh.txt b/Documentation/scsi/scsi_eh.txt index 534a50922a7..331afd791cb 100644 --- a/Documentation/scsi/scsi_eh.txt +++ b/Documentation/scsi/scsi_eh.txt @@ -83,11 +83,11 @@ with the command. The timeout handler is scsi_times_out(). When a timeout occurs, this function - 1. invokes optional hostt->eh_timedout() callback. Return value can + 1. invokes optional hostt->eh_timed_out() callback. Return value can be one of - EH_HANDLED - This indicates that eh_timedout() dealt with the timeout. The + This indicates that eh_timed_out() dealt with the timeout. The scmd is passed to __scsi_done() and thus linked into per-cpu scsi_done_q. Normal command completion described in [1-2-1] follows. @@ -105,7 +105,7 @@ function command will time out again. - EH_NOT_HANDLED - This is the same as when eh_timedout() callback doesn't exist. + This is the same as when eh_timed_out() callback doesn't exist. Step #2 is taken. 2. scsi_eh_scmd_add(scmd, SCSI_EH_CANCEL_CMD) is invoked for the @@ -142,7 +142,7 @@ are linked on shost->eh_cmd_q. Note that this does not mean lower layers are quiescent. If a LLDD completed a scmd with error status, the LLDD and lower layers are assumed to forget about the scmd at that point. However, if a scmd -has timed out, unless hostt->eh_timedout() made lower layers forget +has timed out, unless hostt->eh_timed_out() made lower layers forget about the scmd, which currently no LLDD does, the command is still active as long as lower layers are concerned and completion could occur at any time. Of course, all such completions are ignored as the diff --git a/Documentation/scsi/scsi_mid_low_api.txt b/Documentation/scsi/scsi_mid_low_api.txt index 44df89c9c04..66565d42288 100644 --- a/Documentation/scsi/scsi_mid_low_api.txt +++ b/Documentation/scsi/scsi_mid_low_api.txt @@ -346,7 +346,7 @@ Next, there is a movement to "outlaw" typedefs introducing synonyms for struct tags. Both can be still found in the SCSI subsystem, but the typedefs have been moved to a single file, scsi_typedefs.h to make their future removal easier, for example: -"typedef struct scsi_host_template Scsi_Host_Template;" +"typedef struct scsi_cmnd Scsi_Cmnd;" Also, most C99 enhancements are encouraged to the extent they are supported by the relevant gcc compilers. So C99 style structure and array @@ -718,7 +718,7 @@ void scsi_report_bus_reset(struct Scsi_Host * shost, int channel) * * Defined in: drivers/scsi/scsi.c . **/ -int scsi_track_queue_full(Scsi_Device *sdev, int depth) +int scsi_track_queue_full(struct scsi_device *sdev, int depth) /** diff --git a/Documentation/video4linux/API.html b/Documentation/video4linux/API.html index 441407b12a9..afbe9ae7ee9 100644 --- a/Documentation/video4linux/API.html +++ b/Documentation/video4linux/API.html @@ -8,7 +8,7 @@ V4L original API</a> </td><td> Obsoleted by V4L2 API </td></tr><tr><td> -<A HREF=http://www.linuxtv.org/downloads/video4linux/API/V4L2_API.html> +<A HREF=http://www.linuxtv.org/downloads/video4linux/API/V4L2_API> V4L2 API</a> </td><td> Should be used for new projects diff --git a/Documentation/video4linux/CARDLIST.bttv b/Documentation/video4linux/CARDLIST.bttv index ec785f9f15a..2404099996a 100644 --- a/Documentation/video4linux/CARDLIST.bttv +++ b/Documentation/video4linux/CARDLIST.bttv @@ -1,137 +1,142 @@ -card=0 - *** UNKNOWN/GENERIC *** -card=1 - MIRO PCTV -card=2 - Hauppauge (bt848) -card=3 - STB, Gateway P/N 6000699 (bt848) -card=4 - Intel Create and Share PCI/ Smart Video Recorder III -card=5 - Diamond DTV2000 -card=6 - AVerMedia TVPhone -card=7 - MATRIX-Vision MV-Delta -card=8 - Lifeview FlyVideo II (Bt848) LR26 / MAXI TV Video PCI2 LR26 -card=9 - IMS/IXmicro TurboTV -card=10 - Hauppauge (bt878) -card=11 - MIRO PCTV pro -card=12 - ADS Technologies Channel Surfer TV (bt848) -card=13 - AVerMedia TVCapture 98 -card=14 - Aimslab Video Highway Xtreme (VHX) -card=15 - Zoltrix TV-Max -card=16 - Prolink Pixelview PlayTV (bt878) -card=17 - Leadtek WinView 601 -card=18 - AVEC Intercapture -card=19 - Lifeview FlyVideo II EZ /FlyKit LR38 Bt848 (capture only) -card=20 - CEI Raffles Card -card=21 - Lifeview FlyVideo 98/ Lucky Star Image World ConferenceTV LR50 -card=22 - Askey CPH050/ Phoebe Tv Master + FM -card=23 - Modular Technology MM201/MM202/MM205/MM210/MM215 PCTV, bt878 -card=24 - Askey CPH05X/06X (bt878) [many vendors] -card=25 - Terratec TerraTV+ Version 1.0 (Bt848)/ Terra TValue Version 1.0/ Vobis TV-Boostar -card=26 - Hauppauge WinCam newer (bt878) -card=27 - Lifeview FlyVideo 98/ MAXI TV Video PCI2 LR50 -card=28 - Terratec TerraTV+ Version 1.1 (bt878) -card=29 - Imagenation PXC200 -card=30 - Lifeview FlyVideo 98 LR50 -card=31 - Formac iProTV, Formac ProTV I (bt848) -card=32 - Intel Create and Share PCI/ Smart Video Recorder III -card=33 - Terratec TerraTValue Version Bt878 -card=34 - Leadtek WinFast 2000/ WinFast 2000 XP -card=35 - Lifeview FlyVideo 98 LR50 / Chronos Video Shuttle II -card=36 - Lifeview FlyVideo 98FM LR50 / Typhoon TView TV/FM Tuner -card=37 - Prolink PixelView PlayTV pro -card=38 - Askey CPH06X TView99 -card=39 - Pinnacle PCTV Studio/Rave -card=40 - STB TV PCI FM, Gateway P/N 6000704 (bt878), 3Dfx VoodooTV 100 -card=41 - AVerMedia TVPhone 98 -card=42 - ProVideo PV951 -card=43 - Little OnAir TV -card=44 - Sigma TVII-FM -card=45 - MATRIX-Vision MV-Delta 2 -card=46 - Zoltrix Genie TV/FM -card=47 - Terratec TV/Radio+ -card=48 - Askey CPH03x/ Dynalink Magic TView -card=49 - IODATA GV-BCTV3/PCI -card=50 - Prolink PV-BT878P+4E / PixelView PlayTV PAK / Lenco MXTV-9578 CP -card=51 - Eagle Wireless Capricorn2 (bt878A) -card=52 - Pinnacle PCTV Studio Pro -card=53 - Typhoon TView RDS + FM Stereo / KNC1 TV Station RDS -card=54 - Lifeview FlyVideo 2000 /FlyVideo A2/ Lifetec LT 9415 TV [LR90] -card=55 - Askey CPH031/ BESTBUY Easy TV -card=56 - Lifeview FlyVideo 98FM LR50 -card=57 - GrandTec 'Grand Video Capture' (Bt848) -card=58 - Askey CPH060/ Phoebe TV Master Only (No FM) -card=59 - Askey CPH03x TV Capturer -card=60 - Modular Technology MM100PCTV -card=61 - AG Electronics GMV1 -card=62 - Askey CPH061/ BESTBUY Easy TV (bt878) -card=63 - ATI TV-Wonder -card=64 - ATI TV-Wonder VE -card=65 - Lifeview FlyVideo 2000S LR90 -card=66 - Terratec TValueRadio -card=67 - IODATA GV-BCTV4/PCI -card=68 - 3Dfx VoodooTV FM (Euro), VoodooTV 200 (USA) -card=69 - Active Imaging AIMMS -card=70 - Prolink Pixelview PV-BT878P+ (Rev.4C,8E) -card=71 - Lifeview FlyVideo 98EZ (capture only) LR51 -card=72 - Prolink Pixelview PV-BT878P+9B (PlayTV Pro rev.9B FM+NICAM) -card=73 - Sensoray 311 -card=74 - RemoteVision MX (RV605) -card=75 - Powercolor MTV878/ MTV878R/ MTV878F -card=76 - Canopus WinDVR PCI (COMPAQ Presario 3524JP, 5112JP) -card=77 - GrandTec Multi Capture Card (Bt878) -card=78 - Jetway TV/Capture JW-TV878-FBK, Kworld KW-TV878RF -card=79 - DSP Design TCVIDEO -card=80 - Hauppauge WinTV PVR -card=81 - IODATA GV-BCTV5/PCI -card=82 - Osprey 100/150 (878) -card=83 - Osprey 100/150 (848) -card=84 - Osprey 101 (848) -card=85 - Osprey 101/151 -card=86 - Osprey 101/151 w/ svid -card=87 - Osprey 200/201/250/251 -card=88 - Osprey 200/250 -card=89 - Osprey 210/220 -card=90 - Osprey 500 -card=91 - Osprey 540 -card=92 - Osprey 2000 -card=93 - IDS Eagle -card=94 - Pinnacle PCTV Sat -card=95 - Formac ProTV II (bt878) -card=96 - MachTV -card=97 - Euresys Picolo -card=98 - ProVideo PV150 -card=99 - AD-TVK503 -card=100 - Hercules Smart TV Stereo -card=101 - Pace TV & Radio Card -card=102 - IVC-200 -card=103 - Grand X-Guard / Trust 814PCI -card=104 - Nebula Electronics DigiTV -card=105 - ProVideo PV143 -card=106 - PHYTEC VD-009-X1 MiniDIN (bt878) -card=107 - PHYTEC VD-009-X1 Combi (bt878) -card=108 - PHYTEC VD-009 MiniDIN (bt878) -card=109 - PHYTEC VD-009 Combi (bt878) -card=110 - IVC-100 -card=111 - IVC-120G -card=112 - pcHDTV HD-2000 TV -card=113 - Twinhan DST + clones -card=114 - Winfast VC100 -card=115 - Teppro TEV-560/InterVision IV-560 -card=116 - SIMUS GVC1100 -card=117 - NGS NGSTV+ -card=118 - LMLBT4 -card=119 - Tekram M205 PRO -card=120 - Conceptronic CONTVFMi -card=121 - Euresys Picolo Tetra -card=122 - Spirit TV Tuner -card=123 - AVerMedia AVerTV DVB-T 771 -card=124 - AverMedia AverTV DVB-T 761 -card=125 - MATRIX Vision Sigma-SQ -card=126 - MATRIX Vision Sigma-SLC -card=127 - APAC Viewcomp 878(AMAX) -card=128 - DViCO FusionHDTV DVB-T Lite -card=129 - V-Gear MyVCD -card=130 - Super TV Tuner -card=131 - Tibet Systems 'Progress DVR' CS16 -card=132 - Kodicom 4400R (master) -card=133 - Kodicom 4400R (slave) -card=134 - Adlink RTV24 -card=135 - DViCO FusionHDTV 5 Lite -card=136 - Acorp Y878F + 0 -> *** UNKNOWN/GENERIC *** + 1 -> MIRO PCTV + 2 -> Hauppauge (bt848) + 3 -> STB, Gateway P/N 6000699 (bt848) + 4 -> Intel Create and Share PCI/ Smart Video Recorder III + 5 -> Diamond DTV2000 + 6 -> AVerMedia TVPhone + 7 -> MATRIX-Vision MV-Delta + 8 -> Lifeview FlyVideo II (Bt848) LR26 / MAXI TV Video PCI2 LR26 + 9 -> IMS/IXmicro TurboTV + 10 -> Hauppauge (bt878) [0070:13eb,0070:3900,2636:10b4] + 11 -> MIRO PCTV pro + 12 -> ADS Technologies Channel Surfer TV (bt848) + 13 -> AVerMedia TVCapture 98 [1461:0002,1461:0004,1461:0300] + 14 -> Aimslab Video Highway Xtreme (VHX) + 15 -> Zoltrix TV-Max [a1a0:a0fc] + 16 -> Prolink Pixelview PlayTV (bt878) + 17 -> Leadtek WinView 601 + 18 -> AVEC Intercapture + 19 -> Lifeview FlyVideo II EZ /FlyKit LR38 Bt848 (capture only) + 20 -> CEI Raffles Card + 21 -> Lifeview FlyVideo 98/ Lucky Star Image World ConferenceTV LR50 + 22 -> Askey CPH050/ Phoebe Tv Master + FM [14ff:3002] + 23 -> Modular Technology MM201/MM202/MM205/MM210/MM215 PCTV, bt878 [14c7:0101] + 24 -> Askey CPH05X/06X (bt878) [many vendors] [144f:3002,144f:3005,144f:5000,14ff:3000] + 25 -> Terratec TerraTV+ Version 1.0 (Bt848)/ Terra TValue Version 1.0/ Vobis TV-Boostar + 26 -> Hauppauge WinCam newer (bt878) + 27 -> Lifeview FlyVideo 98/ MAXI TV Video PCI2 LR50 + 28 -> Terratec TerraTV+ Version 1.1 (bt878) [153b:1127,1852:1852] + 29 -> Imagenation PXC200 [1295:200a] + 30 -> Lifeview FlyVideo 98 LR50 [1f7f:1850] + 31 -> Formac iProTV, Formac ProTV I (bt848) + 32 -> Intel Create and Share PCI/ Smart Video Recorder III + 33 -> Terratec TerraTValue Version Bt878 [153b:1117,153b:1118,153b:1119,153b:111a,153b:1134,153b:5018] + 34 -> Leadtek WinFast 2000/ WinFast 2000 XP [107d:6606,107d:6609,6606:217d,f6ff:fff6] + 35 -> Lifeview FlyVideo 98 LR50 / Chronos Video Shuttle II [1851:1850,1851:a050] + 36 -> Lifeview FlyVideo 98FM LR50 / Typhoon TView TV/FM Tuner [1852:1852] + 37 -> Prolink PixelView PlayTV pro + 38 -> Askey CPH06X TView99 [144f:3000,144f:a005,a04f:a0fc] + 39 -> Pinnacle PCTV Studio/Rave [11bd:0012,bd11:1200,bd11:ff00,11bd:ff12] + 40 -> STB TV PCI FM, Gateway P/N 6000704 (bt878), 3Dfx VoodooTV 100 [10b4:2636,10b4:2645,121a:3060] + 41 -> AVerMedia TVPhone 98 [1461:0001,1461:0003] + 42 -> ProVideo PV951 [aa0c:146c] + 43 -> Little OnAir TV + 44 -> Sigma TVII-FM + 45 -> MATRIX-Vision MV-Delta 2 + 46 -> Zoltrix Genie TV/FM [15b0:4000,15b0:400a,15b0:400d,15b0:4010,15b0:4016] + 47 -> Terratec TV/Radio+ [153b:1123] + 48 -> Askey CPH03x/ Dynalink Magic TView + 49 -> IODATA GV-BCTV3/PCI [10fc:4020] + 50 -> Prolink PV-BT878P+4E / PixelView PlayTV PAK / Lenco MXTV-9578 CP + 51 -> Eagle Wireless Capricorn2 (bt878A) + 52 -> Pinnacle PCTV Studio Pro + 53 -> Typhoon TView RDS + FM Stereo / KNC1 TV Station RDS + 54 -> Lifeview FlyVideo 2000 /FlyVideo A2/ Lifetec LT 9415 TV [LR90] + 55 -> Askey CPH031/ BESTBUY Easy TV + 56 -> Lifeview FlyVideo 98FM LR50 [a051:41a0] + 57 -> GrandTec 'Grand Video Capture' (Bt848) [4344:4142] + 58 -> Askey CPH060/ Phoebe TV Master Only (No FM) + 59 -> Askey CPH03x TV Capturer + 60 -> Modular Technology MM100PCTV + 61 -> AG Electronics GMV1 [15cb:0101] + 62 -> Askey CPH061/ BESTBUY Easy TV (bt878) + 63 -> ATI TV-Wonder [1002:0001] + 64 -> ATI TV-Wonder VE [1002:0003] + 65 -> Lifeview FlyVideo 2000S LR90 + 66 -> Terratec TValueRadio [153b:1135,153b:ff3b] + 67 -> IODATA GV-BCTV4/PCI [10fc:4050] + 68 -> 3Dfx VoodooTV FM (Euro), VoodooTV 200 (USA) [121a:3000,10b4:2637] + 69 -> Active Imaging AIMMS + 70 -> Prolink Pixelview PV-BT878P+ (Rev.4C,8E) + 71 -> Lifeview FlyVideo 98EZ (capture only) LR51 [1851:1851] + 72 -> Prolink Pixelview PV-BT878P+9B (PlayTV Pro rev.9B FM+NICAM) [1554:4011] + 73 -> Sensoray 311 [6000:0311] + 74 -> RemoteVision MX (RV605) + 75 -> Powercolor MTV878/ MTV878R/ MTV878F + 76 -> Canopus WinDVR PCI (COMPAQ Presario 3524JP, 5112JP) [0e11:0079] + 77 -> GrandTec Multi Capture Card (Bt878) + 78 -> Jetway TV/Capture JW-TV878-FBK, Kworld KW-TV878RF [0a01:17de] + 79 -> DSP Design TCVIDEO + 80 -> Hauppauge WinTV PVR [0070:4500] + 81 -> IODATA GV-BCTV5/PCI [10fc:4070,10fc:d018] + 82 -> Osprey 100/150 (878) [0070:ff00] + 83 -> Osprey 100/150 (848) + 84 -> Osprey 101 (848) + 85 -> Osprey 101/151 + 86 -> Osprey 101/151 w/ svid + 87 -> Osprey 200/201/250/251 + 88 -> Osprey 200/250 [0070:ff01] + 89 -> Osprey 210/220 + 90 -> Osprey 500 [0070:ff02] + 91 -> Osprey 540 [0070:ff04] + 92 -> Osprey 2000 [0070:ff03] + 93 -> IDS Eagle + 94 -> Pinnacle PCTV Sat [11bd:001c] + 95 -> Formac ProTV II (bt878) + 96 -> MachTV + 97 -> Euresys Picolo + 98 -> ProVideo PV150 [aa00:1460,aa01:1461,aa02:1462,aa03:1463,aa04:1464,aa05:1465,aa06:1466,aa07:1467] + 99 -> AD-TVK503 +100 -> Hercules Smart TV Stereo +101 -> Pace TV & Radio Card +102 -> IVC-200 [0000:a155,0001:a155,0002:a155,0003:a155,0100:a155,0101:a155,0102:a155,0103:a155] +103 -> Grand X-Guard / Trust 814PCI [0304:0102] +104 -> Nebula Electronics DigiTV [0071:0101] +105 -> ProVideo PV143 [aa00:1430,aa00:1431,aa00:1432,aa00:1433,aa03:1433] +106 -> PHYTEC VD-009-X1 MiniDIN (bt878) +107 -> PHYTEC VD-009-X1 Combi (bt878) +108 -> PHYTEC VD-009 MiniDIN (bt878) +109 -> PHYTEC VD-009 Combi (bt878) +110 -> IVC-100 [ff00:a132] +111 -> IVC-120G [ff00:a182,ff01:a182,ff02:a182,ff03:a182,ff04:a182,ff05:a182,ff06:a182,ff07:a182,ff08:a182,ff09:a182,ff0a:a182,ff0b:a182,ff0c:a182,ff0d:a182,ff0e:a182,ff0f:a182] +112 -> pcHDTV HD-2000 TV [7063:2000] +113 -> Twinhan DST + clones [11bd:0026,1822:0001,270f:fc00] +114 -> Winfast VC100 [107d:6607] +115 -> Teppro TEV-560/InterVision IV-560 +116 -> SIMUS GVC1100 [aa6a:82b2] +117 -> NGS NGSTV+ +118 -> LMLBT4 +119 -> Tekram M205 PRO +120 -> Conceptronic CONTVFMi +121 -> Euresys Picolo Tetra [1805:0105,1805:0106,1805:0107,1805:0108] +122 -> Spirit TV Tuner +123 -> AVerMedia AVerTV DVB-T 771 [1461:0771] +124 -> AverMedia AverTV DVB-T 761 [1461:0761] +125 -> MATRIX Vision Sigma-SQ +126 -> MATRIX Vision Sigma-SLC +127 -> APAC Viewcomp 878(AMAX) +128 -> DViCO FusionHDTV DVB-T Lite [18ac:db10] +129 -> V-Gear MyVCD +130 -> Super TV Tuner +131 -> Tibet Systems 'Progress DVR' CS16 +132 -> Kodicom 4400R (master) +133 -> Kodicom 4400R (slave) +134 -> Adlink RTV24 +135 -> DViCO FusionHDTV 5 Lite [18ac:d500] +136 -> Acorp Y878F [9511:1540] +137 -> Conceptronic CTVFMi v2 +138 -> Prolink Pixelview PV-BT878P+ (Rev.2E) +139 -> Prolink PixelView PlayTV MPEG2 PV-M4900 +140 -> Osprey 440 [0070:ff07] +141 -> Asound Skyeye PCTV diff --git a/Documentation/video4linux/CARDLIST.cx88 b/Documentation/video4linux/CARDLIST.cx88 index 03deb0726aa..a1017d1a85d 100644 --- a/Documentation/video4linux/CARDLIST.cx88 +++ b/Documentation/video4linux/CARDLIST.cx88 @@ -1,32 +1,37 @@ -card=0 - UNKNOWN/GENERIC -card=1 - Hauppauge WinTV 34xxx models -card=2 - GDI Black Gold -card=3 - PixelView -card=4 - ATI TV Wonder Pro -card=5 - Leadtek Winfast 2000XP Expert -card=6 - AverTV Studio 303 (M126) -card=7 - MSI TV-@nywhere Master -card=8 - Leadtek Winfast DV2000 -card=9 - Leadtek PVR 2000 -card=10 - IODATA GV-VCP3/PCI -card=11 - Prolink PlayTV PVR -card=12 - ASUS PVR-416 -card=13 - MSI TV-@nywhere -card=14 - KWorld/VStream XPert DVB-T -card=15 - DViCO FusionHDTV DVB-T1 -card=16 - KWorld LTV883RF -card=17 - DViCO FusionHDTV 3 Gold-Q -card=18 - Hauppauge Nova-T DVB-T -card=19 - Conexant DVB-T reference design -card=20 - Provideo PV259 -card=21 - DViCO FusionHDTV DVB-T Plus -card=22 - digitalnow DNTV Live! DVB-T -card=23 - pcHDTV HD3000 HDTV -card=24 - Hauppauge WinTV 28xxx (Roslyn) models -card=25 - Digital-Logic MICROSPACE Entertainment Center (MEC) -card=26 - IODATA GV/BCTV7E -card=27 - PixelView PlayTV Ultra Pro (Stereo) -card=28 - DViCO FusionHDTV 3 Gold-T -card=29 - ADS Tech Instant TV DVB-T PCI -card=30 - TerraTec Cinergy 1400 DVB-T -card=31 - DViCO FusionHDTV 5 Gold + 0 -> UNKNOWN/GENERIC + 1 -> Hauppauge WinTV 34xxx models [0070:3400,0070:3401] + 2 -> GDI Black Gold [14c7:0106,14c7:0107] + 3 -> PixelView [1554:4811] + 4 -> ATI TV Wonder Pro [1002:00f8] + 5 -> Leadtek Winfast 2000XP Expert [107d:6611,107d:6613] + 6 -> AverTV Studio 303 (M126) [1461:000b] + 7 -> MSI TV-@nywhere Master [1462:8606] + 8 -> Leadtek Winfast DV2000 [107d:6620] + 9 -> Leadtek PVR 2000 [107d:663b,107d:663C] + 10 -> IODATA GV-VCP3/PCI [10fc:d003] + 11 -> Prolink PlayTV PVR + 12 -> ASUS PVR-416 [1043:4823] + 13 -> MSI TV-@nywhere + 14 -> KWorld/VStream XPert DVB-T [17de:08a6] + 15 -> DViCO FusionHDTV DVB-T1 [18ac:db00] + 16 -> KWorld LTV883RF + 17 -> DViCO FusionHDTV 3 Gold-Q [18ac:d810] + 18 -> Hauppauge Nova-T DVB-T [0070:9002] + 19 -> Conexant DVB-T reference design [14f1:0187] + 20 -> Provideo PV259 [1540:2580] + 21 -> DViCO FusionHDTV DVB-T Plus [18ac:db10] + 22 -> pcHDTV HD3000 HDTV [7063:3000] + 23 -> digitalnow DNTV Live! DVB-T [17de:a8a6] + 24 -> Hauppauge WinTV 28xxx (Roslyn) models [0070:2801] + 25 -> Digital-Logic MICROSPACE Entertainment Center (MEC) [14f1:0342] + 26 -> IODATA GV/BCTV7E [10fc:d035] + 27 -> PixelView PlayTV Ultra Pro (Stereo) + 28 -> DViCO FusionHDTV 3 Gold-T [18ac:d820] + 29 -> ADS Tech Instant TV DVB-T PCI [1421:0334] + 30 -> TerraTec Cinergy 1400 DVB-T [153b:1166] + 31 -> DViCO FusionHDTV 5 Gold [18ac:d500] + 32 -> AverMedia UltraTV Media Center PCI 550 [1461:8011] + 33 -> Kworld V-Stream Xpert DVD + 34 -> ATI HDTV Wonder [1002:a101] + 35 -> WinFast DTV1000-T [107d:665f] + 36 -> AVerTV 303 (M126) [1461:000a] diff --git a/Documentation/video4linux/CARDLIST.em28xx b/Documentation/video4linux/CARDLIST.em28xx new file mode 100644 index 00000000000..a0c7cad2097 --- /dev/null +++ b/Documentation/video4linux/CARDLIST.em28xx @@ -0,0 +1,10 @@ + 0 -> Unknown EM2800 video grabber (em2800) [eb1a:2800] + 1 -> Unknown EM2820/2840 video grabber (em2820/em2840) + 2 -> Terratec Cinergy 250 USB (em2820/em2840) [0ccd:0036] + 3 -> Pinnacle PCTV USB 2 (em2820/em2840) [2304:0208] + 4 -> Hauppauge WinTV USB 2 (em2820/em2840) [2040:4200] + 5 -> MSI VOX USB 2.0 (em2820/em2840) [eb1a:2820] + 6 -> Terratec Cinergy 200 USB (em2800) + 7 -> Leadtek Winfast USB II (em2800) + 8 -> Kworld USB2800 (em2800) + 9 -> Pinnacle Dazzle DVC 90 (em2820/em2840) [2304:0207] diff --git a/Documentation/video4linux/CARDLIST.saa7134 b/Documentation/video4linux/CARDLIST.saa7134 index dc57225f39b..57c9d631db5 100644 --- a/Documentation/video4linux/CARDLIST.saa7134 +++ b/Documentation/video4linux/CARDLIST.saa7134 @@ -6,10 +6,10 @@ 5 -> SKNet Monster TV [1131:4e85] 6 -> Tevion MD 9717 7 -> KNC One TV-Station RDS / Typhoon TV Tuner RDS [1131:fe01,1894:fe01] - 8 -> Terratec Cinergy 400 TV [153B:1142] + 8 -> Terratec Cinergy 400 TV [153b:1142] 9 -> Medion 5044 10 -> Kworld/KuroutoShikou SAA7130-TVPCI - 11 -> Terratec Cinergy 600 TV [153B:1143] + 11 -> Terratec Cinergy 600 TV [153b:1143] 12 -> Medion 7134 [16be:0003] 13 -> Typhoon TV+Radio 90031 14 -> ELSA EX-VISION 300TV [1048:226b] @@ -36,8 +36,8 @@ 35 -> AverMedia AverTV Studio 305 [1461:2115] 36 -> UPMOST PURPLE TV [12ab:0800] 37 -> Items MuchTV Plus / IT-005 - 38 -> Terratec Cinergy 200 TV [153B:1152] - 39 -> LifeView FlyTV Platinum Mini [5168:0212] + 38 -> Terratec Cinergy 200 TV [153b:1152] + 39 -> LifeView FlyTV Platinum Mini [5168:0212,4e42:0212] 40 -> Compro VideoMate TV PVR/FM [185b:c100] 41 -> Compro VideoMate TV Gold+ [185b:c100] 42 -> Sabrent SBT-TVFM (saa7130) @@ -46,7 +46,7 @@ 45 -> Avermedia AVerTV Studio 307 [1461:9715] 46 -> AVerMedia Cardbus TV/Radio (E500) [1461:d6ee] 47 -> Terratec Cinergy 400 mobile [153b:1162] - 48 -> Terratec Cinergy 600 TV MK3 [153B:1158] + 48 -> Terratec Cinergy 600 TV MK3 [153b:1158] 49 -> Compro VideoMate Gold+ Pal [185b:c200] 50 -> Pinnacle PCTV 300i DVB-T + PAL [11bd:002d] 51 -> ProVideo PV952 [1540:9524] @@ -56,12 +56,27 @@ 55 -> LifeView FlyDVB-T DUO [5168:0502,5168:0306] 56 -> Avermedia AVerTV 307 [1461:a70a] 57 -> Avermedia AVerTV GO 007 FM [1461:f31f] - 58 -> ADS Tech Instant TV (saa7135) [1421:0350,1421:0370] + 58 -> ADS Tech Instant TV (saa7135) [1421:0350,1421:0370,1421:1370] 59 -> Kworld/Tevion V-Stream Xpert TV PVR7134 60 -> Typhoon DVB-T Duo Digital/Analog Cardbus [4e42:0502] 61 -> Philips TOUGH DVB-T reference design [1131:2004] 62 -> Compro VideoMate TV Gold+II 63 -> Kworld Xpert TV PVR7134 - 64 -> FlyTV mini Asus Digimatrix [1043:0210,1043:0210] + 64 -> FlyTV mini Asus Digimatrix [1043:0210] 65 -> V-Stream Studio TV Terminator 66 -> Yuan TUN-900 (saa7135) + 67 -> Beholder BeholdTV 409 FM [0000:4091] + 68 -> GoTView 7135 PCI [5456:7135] + 69 -> Philips EUROPA V3 reference design [1131:2004] + 70 -> Compro Videomate DVB-T300 [185b:c900] + 71 -> Compro Videomate DVB-T200 [185b:c901] + 72 -> RTD Embedded Technologies VFG7350 [1435:7350] + 73 -> RTD Embedded Technologies VFG7330 [1435:7330] + 74 -> LifeView FlyTV Platinum Mini2 [14c0:1212] + 75 -> AVerMedia AVerTVHD MCE A180 [1461:1044] + 76 -> SKNet MonsterTV Mobile [1131:4ee9] + 77 -> Pinnacle PCTV 110i (saa7133) [11bd:002e] + 78 -> ASUSTeK P7131 Dual [1043:4862] + 79 -> Sedna/MuchTV PC TV Cardbus TV/Radio (ITO25 Rev:2B) + 80 -> ASUS Digimatrix TV [1043:0210] + 81 -> Philips Tiger reference design [1131:2018] diff --git a/Documentation/video4linux/CARDLIST.tuner b/Documentation/video4linux/CARDLIST.tuner index f5876be658a..ec840ca6f45 100644 --- a/Documentation/video4linux/CARDLIST.tuner +++ b/Documentation/video4linux/CARDLIST.tuner @@ -53,7 +53,7 @@ tuner=51 - Philips PAL/SECAM_D (FM 1256 I-H3) tuner=52 - Thomson DDT 7610 (ATSC/NTSC) tuner=53 - Philips FQ1286 tuner=54 - tda8290+75 -tuner=55 - LG PAL (TAPE series) +tuner=55 - TCL 2002MB tuner=56 - Philips PAL/SECAM multi (FQ1216AME MK4) tuner=57 - Philips FQ1236A MK4 tuner=58 - Ymec TVision TVF-8531MF/8831MF/8731MF @@ -65,3 +65,5 @@ tuner=63 - Philips FMD1216ME MK3 Hybrid Tuner tuner=64 - LG TDVS-H062F/TUA6034 tuner=65 - Ymec TVF66T5-B/DFF tuner=66 - LG NTSC (TALN mini series) +tuner=67 - Philips TD1316 Hybrid Tuner +tuner=68 - Philips TUV1236D ATSC/NTSC dual in diff --git a/Documentation/video4linux/README.cx88 b/Documentation/video4linux/README.cx88 index 897ab834839..06a33a4f52f 100644 --- a/Documentation/video4linux/README.cx88 +++ b/Documentation/video4linux/README.cx88 @@ -17,9 +17,9 @@ audio - The chip specs for the on-chip TV sound decoder are next to useless :-/ - Neverless the builtin TV sound decoder starts working now, - at least for PAL-BG. Other TV norms need other code ... - FOR ANY REPORTS ON THIS PLEASE MENTION THE TV NORM YOU ARE - USING. + at least for PAL-BG. Other TV norms need other code ... + FOR ANY REPORTS ON THIS PLEASE MENTION THE TV NORM YOU ARE + USING. - Most tuner chips do provide mono sound, which may or may not be useable depending on the board design. With the Hauppauge cards it works, so there is mono sound available as fallback. @@ -65,5 +65,5 @@ Have fun, Gerd --- +-- Gerd Knorr <kraxel@bytesex.org> [SuSE Labs] diff --git a/Documentation/video4linux/README.saa7134 b/Documentation/video4linux/README.saa7134 index 1f788e498ef..b911f087187 100644 --- a/Documentation/video4linux/README.saa7134 +++ b/Documentation/video4linux/README.saa7134 @@ -78,5 +78,5 @@ Have fun, Gerd --- +-- Gerd Knorr <kraxel@bytesex.org> [SuSE Labs] diff --git a/Documentation/video4linux/bttv/Cards b/Documentation/video4linux/bttv/Cards index 8f1941ede4d..d3389655ad9 100644 --- a/Documentation/video4linux/bttv/Cards +++ b/Documentation/video4linux/bttv/Cards @@ -149,11 +149,11 @@ Lifeview Flyvideo Series: 2) There is a print on the PCB: LR25 = Flyvideo (Zoran ZR36120, SAA7110A) LR26 Rev.N = Flyvideo II (Bt848) - Rev.O = Flyvideo II (Bt878) + Rev.O = Flyvideo II (Bt878) LR37 Rev.C = Flyvideo EZ (Capture only, ZR36120 + SAA7110) LR38 Rev.A1= Flyvideo II EZ (Bt848 capture only) LR50 Rev.Q = Flyvideo 98 (w/eeprom and PCI subsystem ID) - Rev.W = Flyvideo 98 (no eeprom) + Rev.W = Flyvideo 98 (no eeprom) LR51 Rev.E = Flyvideo 98 EZ (capture only) LR90 = Flyvideo 2000 (Bt878) Flyvideo 2000S (Bt878) w/Stereo TV (Package incl. LR91 daughterboard) @@ -163,7 +163,7 @@ Lifeview Flyvideo Series: LR136 = Flyvideo 2100/3100 (Low profile, SAA7130/SAA7134) LR137 = Flyvideo DV2000/DV3000 (SAA7130/SAA7134 + IEEE1394) LR138 Rev.C= Flyvideo 2000 (SAA7130) - or Flyvideo 3000 (SAA7134) w/Stereo TV + or Flyvideo 3000 (SAA7134) w/Stereo TV These exist in variations w/FM and w/Remote sometimes denoted by suffixes "FM" and "R". 3) You have a laptop (miniPCI card): @@ -197,7 +197,7 @@ Typhoon TV card series: 50680 "TV Tuner Pal BG" (blue package)= Pixelview PV-BT878P+ (Rev 9B) 50681 "TV Tuner PCI Pal I" (variant of 50680) 50682 "TView TV/FM Tuner Pal BG" = Flyvideo 98FM (LR50 Rev.Q) - Note: The package has a picture of CPH05x (which would be a real TView) + Note: The package has a picture of CPH05x (which would be a real TView) 50683 "TV Tuner PCI SECAM" (variant of 50680) 50684 "TV Tuner Pal BG" = Pixelview 878TV(Rev.3D) 50686 "TV Tuner" = KNC1 TV Station @@ -418,9 +418,9 @@ Lifetec/Medion/Tevion/Aldi -------------------------- LT9306/MD9306 = CPH061 LT9415/MD9415 = LR90 Rev.F or Rev.G - MD9592 = Avermedia TVphone98 (PCI_ID=1461:0003), PCB-Rev=M168II-B (w/TDA9873H) - MD9717 = KNC One (Rev D4, saa7134, FM1216 MK2 tuner) - MD5044 = KNC One (Rev D4, saa7134, FM1216ME MK3 tuner) + MD9592 = Avermedia TVphone98 (PCI_ID=1461:0003), PCB-Rev=M168II-B (w/TDA9873H) + MD9717 = KNC One (Rev D4, saa7134, FM1216 MK2 tuner) + MD5044 = KNC One (Rev D4, saa7134, FM1216ME MK3 tuner) Modular Technologies (www.modulartech.com) UK --------------------------------------------- @@ -453,10 +453,10 @@ Technisat Discos ADR PC-Karte ISA (no TV!) Discos ADR PC-Karte PCI (probably no TV?) Techni-PC-Sat (Sat. analog) - Rev 1.2 (zr36120, vpx3220, stv0030, saa5246, BSJE3-494A) + Rev 1.2 (zr36120, vpx3220, stv0030, saa5246, BSJE3-494A) Mediafocus I (zr36120/zr36125, drp3510, Sat. analog + ADR Radio) Mediafocus II (saa7146, Sat. analog) - SatADR Rev 2.1 (saa7146a, saa7113h, stv0056a, msp3400c, drp3510a, BSKE3-307A) + SatADR Rev 2.1 (saa7146a, saa7113h, stv0056a, msp3400c, drp3510a, BSKE3-307A) SkyStar 1 DVB (AV7110) = Technotrend Premium SkyStar 2 DVB (B2C2) (=Sky2PC) diff --git a/Documentation/video4linux/bttv/README b/Documentation/video4linux/bttv/README index a72f4c94fb0..7ca2154c2bf 100644 --- a/Documentation/video4linux/bttv/README +++ b/Documentation/video4linux/bttv/README @@ -42,9 +42,9 @@ bttv uses the PCI Subsystem ID to autodetect the card type. lspci lists the Subsystem ID in the second line, looks like this: 00:0a.0 Multimedia video controller: Brooktree Corporation Bt878 (rev 02) - Subsystem: Hauppauge computer works Inc. WinTV/GO - Flags: bus master, medium devsel, latency 32, IRQ 5 - Memory at e2000000 (32-bit, prefetchable) [size=4K] + Subsystem: Hauppauge computer works Inc. WinTV/GO + Flags: bus master, medium devsel, latency 32, IRQ 5 + Memory at e2000000 (32-bit, prefetchable) [size=4K] only bt878-based cards can have a subsystem ID (which does not mean that every card really has one). bt848 cards can't have a Subsystem diff --git a/Documentation/video4linux/bttv/Sound-FAQ b/Documentation/video4linux/bttv/Sound-FAQ index b8c9c2605ce..1e6328f9108 100644 --- a/Documentation/video4linux/bttv/Sound-FAQ +++ b/Documentation/video4linux/bttv/Sound-FAQ @@ -61,8 +61,8 @@ line for your board. The important fields are these two: struct tvcard { [ ... ] - u32 gpiomask; - u32 audiomux[6]; /* Tuner, Radio, external, internal, mute, stereo */ + u32 gpiomask; + u32 audiomux[6]; /* Tuner, Radio, external, internal, mute, stereo */ }; gpiomask specifies which pins are used to control the audio mux chip. @@ -126,11 +126,11 @@ muxsel - video mux, input->registervalue mapping pll - same as pll= insmod option tuner_type - same as tuner= insmod option *_modulename - hint whenever some card needs this or that audio - module loaded to work properly. + module loaded to work properly. has_radio - whenever this TV card has a radio tuner. no_msp34xx - "1" disables loading of msp3400.o module -no_tda9875 - "1" disables loading of tda9875.o module -needs_tvaudio - set to "1" to load tvaudio.o module +no_tda9875 - "1" disables loading of tda9875.o module +needs_tvaudio - set to "1" to load tvaudio.o module If some config item is specified both from the tvcards array and as insmod option, the insmod option takes precedence. @@ -144,5 +144,5 @@ Good luck, PS: If you have a new working entry, mail it to me. --- +-- Gerd Knorr <kraxel@bytesex.org> diff --git a/Documentation/video4linux/bttv/Tuners b/Documentation/video4linux/bttv/Tuners index d18fbc70c0e..0a371d34954 100644 --- a/Documentation/video4linux/bttv/Tuners +++ b/Documentation/video4linux/bttv/Tuners @@ -21,7 +21,7 @@ SAMSUNG Tuner identification: (e.g. TCPM9091PD27) J= NTSC-Japan L= Secam LL M= BG+I+DK - N= NTSC + N= NTSC Q= BG+I+DK+LL [89]: ? [125]: @@ -96,7 +96,7 @@ LG Innotek Tuner: TADC-H002F: NTSC (L,175/410?; 2-B, C-W+11, W+12-69) TADC-M201D: PAL D/K+B/G+I (L,143/425) (sound control at I2C address 0xc8) TADC-T003F: NTSC Taiwan (L,175/410?; 2-B, C-W+11, W+12-69) - Suffix: + Suffix: P= Standard phono female socket D= IEC female socket F= F-connector diff --git a/Documentation/video4linux/lifeview.txt b/Documentation/video4linux/lifeview.txt index b07ea79c2b7..05f9eb57aac 100644 --- a/Documentation/video4linux/lifeview.txt +++ b/Documentation/video4linux/lifeview.txt @@ -10,33 +10,33 @@ bt878: ------------------------------------------------------------------------------ saa7134: - /* LifeView FlyTV Platinum FM (LR214WF) */ - /* "Peter Missel <peter.missel@onlinehome.de> */ - .name = "LifeView FlyTV Platinum FM", - /* GP27 MDT2005 PB4 pin 10 */ - /* GP26 MDT2005 PB3 pin 9 */ - /* GP25 MDT2005 PB2 pin 8 */ - /* GP23 MDT2005 PB1 pin 7 */ - /* GP22 MDT2005 PB0 pin 6 */ - /* GP21 MDT2005 PB5 pin 11 */ - /* GP20 MDT2005 PB6 pin 12 */ - /* GP19 MDT2005 PB7 pin 13 */ - /* nc MDT2005 PA3 pin 2 */ - /* Remote MDT2005 PA2 pin 1 */ - /* GP18 MDT2005 PA1 pin 18 */ - /* nc MDT2005 PA0 pin 17 strap low */ + /* LifeView FlyTV Platinum FM (LR214WF) */ + /* "Peter Missel <peter.missel@onlinehome.de> */ + .name = "LifeView FlyTV Platinum FM", + /* GP27 MDT2005 PB4 pin 10 */ + /* GP26 MDT2005 PB3 pin 9 */ + /* GP25 MDT2005 PB2 pin 8 */ + /* GP23 MDT2005 PB1 pin 7 */ + /* GP22 MDT2005 PB0 pin 6 */ + /* GP21 MDT2005 PB5 pin 11 */ + /* GP20 MDT2005 PB6 pin 12 */ + /* GP19 MDT2005 PB7 pin 13 */ + /* nc MDT2005 PA3 pin 2 */ + /* Remote MDT2005 PA2 pin 1 */ + /* GP18 MDT2005 PA1 pin 18 */ + /* nc MDT2005 PA0 pin 17 strap low */ - /* GP17 Strap "GP7"=High */ - /* GP16 Strap "GP6"=High - 0=Radio 1=TV - Drives SA630D ENCH1 and HEF4052 A1 pins - to do FM radio through SIF input */ - /* GP15 nc */ - /* GP14 nc */ - /* GP13 nc */ - /* GP12 Strap "GP5" = High */ - /* GP11 Strap "GP4" = High */ - /* GP10 Strap "GP3" = High */ - /* GP09 Strap "GP2" = Low */ - /* GP08 Strap "GP1" = Low */ - /* GP07.00 nc */ + /* GP17 Strap "GP7"=High */ + /* GP16 Strap "GP6"=High + 0=Radio 1=TV + Drives SA630D ENCH1 and HEF4052 A1 pins + to do FM radio through SIF input */ + /* GP15 nc */ + /* GP14 nc */ + /* GP13 nc */ + /* GP12 Strap "GP5" = High */ + /* GP11 Strap "GP4" = High */ + /* GP10 Strap "GP3" = High */ + /* GP09 Strap "GP2" = Low */ + /* GP08 Strap "GP1" = Low */ + /* GP07.00 nc */ |