1 files changed, 83 insertions, 17 deletions

diff --git a/arch/arm/mach-pxa/gumstix.c b/arch/arm/mach-pxa/gumstix.c
index c0092472fa5..d8962a0fb98 100644
--- a/arch/arm/mach-pxa/gumstix.c
+++ b/arch/arm/mach-pxa/gumstix.c
@@ -20,8 +20,12 @@
 #include <linux/init.h>
 #include <linux/platform_device.h>
 #include <linux/interrupt.h>
+#include <linux/delay.h>
 #include <linux/mtd/mtd.h>
 #include <linux/mtd/partitions.h>
+#include <linux/gpio.h>
+#include <linux/err.h>
+#include <linux/clk.h>
 
 #include <asm/setup.h>
 #include <asm/memory.h>
@@ -40,7 +44,7 @@
 
 #include <mach/pxa-regs.h>
 #include <mach/pxa2xx-regs.h>
-#include <mach/pxa2xx-gpio.h>
+#include <mach/mfp-pxa25x.h>
 
 #include "generic.h"
 
@@ -85,21 +89,8 @@ static struct platform_device *devices[] __initdata = {
 };
 
 #ifdef CONFIG_MMC_PXA
-static struct pxamci_platform_data gumstix_mci_platform_data;
-
-static int gumstix_mci_init(struct device *dev, irq_handler_t detect_int,
-				void *data)
-{
-	pxa_gpio_mode(GPIO6_MMCCLK_MD);
-	pxa_gpio_mode(GPIO53_MMCCLK_MD);
-	pxa_gpio_mode(GPIO8_MMCCS0_MD);
-
-	return 0;
-}
-
 static struct pxamci_platform_data gumstix_mci_platform_data = {
 	.ocr_mask	= MMC_VDD_32_33|MMC_VDD_33_34,
-	.init		= gumstix_mci_init,
 };
 
 static void __init gumstix_mmc_init(void)
@@ -109,11 +100,11 @@ static void __init gumstix_mmc_init(void)
 #else
 static void __init gumstix_mmc_init(void)
 {
-	printk(KERN_INFO "Gumstix mmc disabled\n");
+	pr_debug("Gumstix mmc disabled\n");
 }
 #endif
 
-#ifdef CONFIG_USB_GADGET_PXA2XX
+#ifdef CONFIG_USB_GADGET_PXA25X
 static struct pxa2xx_udc_mach_info gumstix_udc_info __initdata = {
 	.gpio_vbus		= GPIO_GUMSTIX_USB_GPIOn,
 	.gpio_pullup		= GPIO_GUMSTIX_USB_GPIOx,
@@ -126,12 +117,87 @@ static void __init gumstix_udc_init(void)
 #else
 static void gumstix_udc_init(void)
 {
-	printk(KERN_INFO "Gumstix udc is disabled\n");
+	pr_debug("Gumstix udc is disabled\n");
 }
 #endif
 
+#ifdef CONFIG_BT
+/* Normally, the bootloader would have enabled this 32kHz clock but many
+** boards still have u-boot 1.1.4 so we check if it has been turned on and
+** if not, we turn it on with a warning message. */
+static void gumstix_setup_bt_clock(void)
+{
+	int timeout = 500;
+
+	if (!(OSCC & OSCC_OOK))
+		pr_warning("32kHz clock was not on. Bootloader may need to "
+				"be updated\n");
+	else
+		return;
+
+	OSCC |= OSCC_OON;
+	do {
+		if (OSCC & OSCC_OOK)
+			break;
+		udelay(1);
+	} while (--timeout);
+	if (!timeout)
+		pr_err("Failed to start 32kHz clock\n");
+}
+
+static void __init gumstix_bluetooth_init(void)
+{
+	int err;
+
+	gumstix_setup_bt_clock();
+
+	err = gpio_request(GPIO_GUMSTIX_BTRESET, "BTRST");
+	if (err) {
+		pr_err("gumstix: failed request gpio for bluetooth reset\n");
+		return;
+	}
+
+	err = gpio_direction_output(GPIO_GUMSTIX_BTRESET, 1);
+	if (err) {
+		pr_err("gumstix: can't reset bluetooth\n");
+		return;
+	}
+	gpio_set_value(GPIO_GUMSTIX_BTRESET, 0);
+	udelay(100);
+	gpio_set_value(GPIO_GUMSTIX_BTRESET, 1);
+}
+#else
+static void gumstix_bluetooth_init(void)
+{
+	pr_debug("Gumstix Bluetooth is disabled\n");
+}
+#endif
+
+static unsigned long gumstix_pin_config[] __initdata = {
+	GPIO12_32KHz,
+	/* BTUART */
+	GPIO42_HWUART_RXD,
+	GPIO43_HWUART_TXD,
+	GPIO44_HWUART_CTS,
+	GPIO45_HWUART_RTS,
+	/* MMC */
+	GPIO6_MMC_CLK,
+	GPIO53_MMC_CLK,
+	GPIO8_MMC_CS0,
+	/* these are used by AM200EPD */
+	GPIO51_GPIO,
+	GPIO49_GPIO,
+	GPIO48_GPIO,
+	GPIO32_GPIO,
+	GPIO17_GPIO,
+	GPIO16_GPIO,
+};
+
 static void __init gumstix_init(void)
 {
+	pxa2xx_mfp_config(ARRAY_AND_SIZE(gumstix_pin_config));
+
+	gumstix_bluetooth_init();
 	gumstix_udc_init();
 	gumstix_mmc_init();
 	(void) platform_add_devices(devices, ARRAY_SIZE(devices));