diff options
Diffstat (limited to 'arch/arm/mach-pxa')
153 files changed, 20048 insertions, 3689 deletions
diff --git a/arch/arm/mach-pxa/Kconfig b/arch/arm/mach-pxa/Kconfig index 5da7a682049..f27f6b3d6e6 100644 --- a/arch/arm/mach-pxa/Kconfig +++ b/arch/arm/mach-pxa/Kconfig @@ -16,31 +16,45 @@ config CPU_PXA310 config CPU_PXA320 bool "PXA320 (codename Monahans-P)" +config CPU_PXA930 + bool "PXA930 (codename Tavor-P)" + endmenu endif -choice - prompt "Select target board" - config ARCH_GUMSTIX bool "Gumstix XScale boards" help Say Y here if you intend to run this kernel on a Gumstix Full Function Minature Computer. +config MACH_GUMSTIX_F + bool "Basix, Connex, ws-200ax, ws-400ax systems" + depends on ARCH_GUMSTIX + select PXA25x + config ARCH_LUBBOCK bool "Intel DBPXA250 Development Platform" select PXA25x select SA1111 + select PXA_HAVE_BOARD_IRQS config MACH_LOGICPD_PXA270 bool "LogicPD PXA270 Card Engine Development Platform" select PXA27x + select HAVE_PWM + select PXA_HAVE_BOARD_IRQS config MACH_MAINSTONE bool "Intel HCDDBBVA0 Development Platform" select PXA27x + select HAVE_PWM + select PXA_HAVE_BOARD_IRQS + +config MACH_MP900C + bool "Nec Mobilepro 900/c" + select PXA25x config ARCH_PXA_IDP bool "Accelent Xscale IDP" @@ -57,9 +71,71 @@ config PXA_SHARPSL SL-C3000 (Spitz), SL-C3100 (Borzoi) or SL-C6000x (Tosa) handheld computer. +config MACH_POODLE + bool "Enable Sharp SL-5600 (Poodle) Support" + depends on PXA_SHARPSL + select PXA25x + select SHARP_LOCOMO + select PXA_SSP + +config MACH_CORGI + bool "Enable Sharp SL-C700 (Corgi) Support" + depends on PXA_SHARPSL + select PXA25x + select PXA_SHARP_C7xx + +config MACH_SHEPHERD + bool "Enable Sharp SL-C750 (Shepherd) Support" + depends on PXA_SHARPSL + select PXA25x + select PXA_SHARP_C7xx + +config MACH_HUSKY + bool "Enable Sharp SL-C760 (Husky) Support" + depends on PXA_SHARPSL + select PXA25x + select PXA_SHARP_C7xx + +config MACH_AKITA + bool "Enable Sharp SL-1000 (Akita) Support" + depends on PXA_SHARPSL + select PXA27x + select PXA_SHARP_Cxx00 + select MACH_SPITZ + select I2C + select I2C_PXA + +config MACH_SPITZ + bool "Enable Sharp Zaurus SL-3000 (Spitz) Support" + depends on PXA_SHARPSL + select PXA27x + select PXA_SHARP_Cxx00 + +config MACH_BORZOI + bool "Enable Sharp Zaurus SL-3100 (Borzoi) Support" + depends on PXA_SHARPSL + select PXA27x + select PXA_SHARP_Cxx00 + +config MACH_TOSA + bool "Enable Sharp SL-6000x (Tosa) Support" + depends on PXA_SHARPSL + select PXA25x + select PXA_HAVE_BOARD_IRQS + +config ARCH_VIPER + bool "Arcom/Eurotech VIPER SBC" + select PXA25x + select ISA + select I2C_GPIO + select HAVE_PWM + select PXA_HAVE_BOARD_IRQS + select PXA_HAVE_ISA_IRQS + config ARCH_PXA_ESERIES bool "PXA based Toshiba e-series PDAs" select PXA25x + select PXA_HAVE_BOARD_IRQS config MACH_E330 bool "Toshiba e330" @@ -69,10 +145,19 @@ config MACH_E330 Say Y here if you intend to run this kernel on a Toshiba e330 family PDA. +config MACH_E350 + bool "Toshiba e350" + default y + depends on ARCH_PXA_ESERIES + help + Say Y here if you intend to run this kernel on a Toshiba + e350 family PDA. + config MACH_E740 bool "Toshiba e740" default y depends on ARCH_PXA_ESERIES + select FB_W100 help Say Y here if you intend to run this kernel on a Toshiba e740 family PDA. @@ -81,6 +166,7 @@ config MACH_E750 bool "Toshiba e750" default y depends on ARCH_PXA_ESERIES + select FB_W100 help Say Y here if you intend to run this kernel on a Toshiba e750 family PDA. @@ -97,14 +183,47 @@ config MACH_E800 bool "Toshiba e800" default y depends on ARCH_PXA_ESERIES + select FB_W100 help Say Y here if you intend to run this kernel on a Toshiba e800 family PDA. +config TRIZEPS_PXA + bool "PXA based Keith und Koep Trizeps DIMM-Modules" + config MACH_TRIZEPS4 bool "Keith und Koep Trizeps4 DIMM-Module" + depends on TRIZEPS_PXA + select TRIZEPS_PCMCIA select PXA27x +config MACH_TRIZEPS4WL + bool "Keith und Koep Trizeps4-WL DIMM-Module" + depends on TRIZEPS_PXA + select TRIZEPS_PCMCIA + select PXA27x + select PXA_SSP + +choice + prompt "Select base board for Trizeps module" + depends on TRIZEPS_PXA + +config MACH_TRIZEPS_CONXS + bool "ConXS Eval Board" + +config MACH_TRIZEPS_UCONXS + bool "uConXS Eval Board" + +config MACH_TRIZEPS_ANY + bool "another Board" + +endchoice + +config TRIZEPS_PCMCIA + bool + help + Enable PCMCIA support for Trizeps modules + config MACH_EM_X270 bool "CompuLab EM-x270 platform" select PXA27x @@ -114,132 +233,150 @@ config MACH_COLIBRI select PXA27x config MACH_ZYLONITE - bool "PXA3xx Development Platform" + bool "PXA3xx Development Platform (aka Zylonite)" select PXA3xx + select PXA_SSP + select HAVE_PWM config MACH_LITTLETON bool "PXA3xx Form Factor Platform (aka Littleton)" select PXA3xx select PXA_SSP +config MACH_TAVOREVB + bool "PXA930 Evaluation Board (aka TavorEVB)" + select PXA3xx + select PXA930 + +config MACH_SAAR + bool "PXA930 Handheld Platform (aka SAAR)" + select PXA3xx + select PXA930 + config MACH_ARMCORE - bool "CompuLab CM-X270 modules" + bool "CompuLab CM-X255/CM-X270 modules" select PXA27x select IWMMXT + select ZONE_DMA if PCI + select PXA25x + select PXA_SSP + +config MACH_CM_X300 + bool "CompuLab CM-X300 modules" + select PXA3xx + select CPU_PXA300 config MACH_MAGICIAN bool "Enable HTC Magician Support" - depends on ARCH_PXA select PXA27x select IWMMXT + select PXA_HAVE_BOARD_IRQS + +config MACH_MIOA701 + bool "Mitac Mio A701 Support" + select PXA27x + select IWMMXT + select LEDS_GPIO + select HAVE_PWM + select GPIO_SYSFS + help + Say Y here if you intend to run this kernel on a + MIO A701. Currently there is only basic support + for this PDA. config MACH_PCM027 bool "Phytec phyCORE-PXA270 CPU module (PCM-027)" select PXA27x select IWMMXT + select PXA_SSP + select PXA_HAVE_BOARD_IRQS -endchoice +config ARCH_PXA_PALM + bool "PXA based Palm PDAs" + select HAVE_PWM -choice - prompt "Used baseboard" - depends on MACH_PCM027 +config MACH_PALMTX + bool "Palm T|X" + default y + depends on ARCH_PXA_PALM + select PXA27x + select IWMMXT + help + Say Y here if you intend to run this kernel on a Palm T|X + handheld computer. + +config MACH_PALMZ72 + bool "Palm Zire 72" + default y + depends on ARCH_PXA_PALM + select PXA27x + select IWMMXT + help + Say Y here if you intend to run this kernel on Palm Zire 72 + handheld computer. config MACH_PCM990_BASEBOARD bool "PHYTEC PCM-990 development board" - -endchoice - -if PXA_SHARPSL + select HAVE_PWM + depends on MACH_PCM027 choice - prompt "Select target Sharp Zaurus device range" + prompt "display on pcm990" + depends on MACH_PCM990_BASEBOARD -config PXA_SHARPSL_25x - bool "Sharp PXA25x models (SL-5600, SL-C7xx and SL-C6000x)" - select PXA25x +config PCM990_DISPLAY_SHARP + bool "sharp lq084v1dg21 stn display" -config PXA_SHARPSL_27x - bool "Sharp PXA270 models (SL-Cxx00)" - select PXA27x +config PCM990_DISPLAY_NEC + bool "nec nl6448bc20_18d tft display" -endchoice - -endif - -if ARCH_GUMSTIX - -choice - prompt "Select target Gumstix board" - -config MACH_GUMSTIX_F - bool "Basix, Connex, ws-200ax, ws-400ax systems" - select PXA25x +config PCM990_DISPLAY_NONE + bool "no display" endchoice -endif +config MACH_AM200EPD + depends on MACH_GUMSTIX_F + bool "Enable AM200EPD board support" +config PXA_EZX + bool "Motorola EZX Platform" + select PXA27x + select IWMMXT + select HAVE_PWM -if MACH_TRIZEPS4 +config MACH_EZX_A780 + bool "Motorola EZX A780" + default y + depends on PXA_EZX -choice - prompt "Select base board for Trizeps 4 module" +config MACH_EZX_E680 + bool "Motorola EZX E680" + default y + depends on PXA_EZX -config MACH_TRIZEPS4_CONXS - bool "ConXS Eval Board" +config MACH_EZX_A1200 + bool "Motorola EZX A1200" + default y + depends on PXA_EZX -config MACH_TRIZEPS4_ANY - bool "another Board" +config MACH_EZX_A910 + bool "Motorola EZX A910" + default y + depends on PXA_EZX -endchoice +config MACH_EZX_E6 + bool "Motorola EZX E6" + default y + depends on PXA_EZX -endif +config MACH_EZX_E2 + bool "Motorola EZX E2" + default y + depends on PXA_EZX endmenu -config MACH_POODLE - bool "Enable Sharp SL-5600 (Poodle) Support" - depends on PXA_SHARPSL_25x - select SHARP_LOCOMO - select PXA_SSP - -config MACH_CORGI - bool "Enable Sharp SL-C700 (Corgi) Support" - depends on PXA_SHARPSL_25x - select PXA_SHARP_C7xx - -config MACH_SHEPHERD - bool "Enable Sharp SL-C750 (Shepherd) Support" - depends on PXA_SHARPSL_25x - select PXA_SHARP_C7xx - -config MACH_HUSKY - bool "Enable Sharp SL-C760 (Husky) Support" - depends on PXA_SHARPSL_25x - select PXA_SHARP_C7xx - -config MACH_AKITA - bool "Enable Sharp SL-1000 (Akita) Support" - depends on PXA_SHARPSL_27x - select PXA_SHARP_Cxx00 - select MACH_SPITZ - select I2C - select I2C_PXA - -config MACH_SPITZ - bool "Enable Sharp Zaurus SL-3000 (Spitz) Support" - depends on PXA_SHARPSL_27x - select PXA_SHARP_Cxx00 - -config MACH_BORZOI - bool "Enable Sharp Zaurus SL-3100 (Borzoi) Support" - depends on PXA_SHARPSL_27x - select PXA_SHARP_Cxx00 - -config MACH_TOSA - bool "Enable Sharp SL-6000x (Tosa) Support" - depends on PXA_SHARPSL_25x - config PXA25x bool help @@ -273,4 +410,25 @@ config PXA_SSP tristate help Enable support for PXA2xx SSP ports + +config PXA_PWM + tristate + default BACKLIGHT_PWM + help + Enable support for PXA2xx/PXA3xx PWM controllers + +config TOSA_BT + tristate "Control the state of built-in bluetooth chip on Sharp SL-6000" + depends on MACH_TOSA + select RFKILL + help + This is a simple driver that is able to control + the state of built in bluetooth chip on tosa. + +config PXA_HAVE_BOARD_IRQS + bool + +config PXA_HAVE_ISA_IRQS + bool + endif diff --git a/arch/arm/mach-pxa/Makefile b/arch/arm/mach-pxa/Makefile index 0e6d05bb81a..d31c9979cfa 100644 --- a/arch/arm/mach-pxa/Makefile +++ b/arch/arm/mach-pxa/Makefile @@ -4,38 +4,56 @@ # Common support (must be linked before board specific support) obj-y += clock.o devices.o generic.o irq.o dma.o \ - time.o gpio.o + time.o gpio.o reset.o obj-$(CONFIG_PM) += pm.o sleep.o standby.o -obj-$(CONFIG_CPU_FREQ) += cpu-pxa.o + +ifeq ($(CONFIG_CPU_FREQ),y) +obj-$(CONFIG_PXA25x) += cpufreq-pxa2xx.o +obj-$(CONFIG_PXA27x) += cpufreq-pxa2xx.o +obj-$(CONFIG_PXA3xx) += cpufreq-pxa3xx.o +endif # Generic drivers that other drivers may depend upon obj-$(CONFIG_PXA_SSP) += ssp.o +obj-$(CONFIG_PXA_PWM) += pwm.o # SoC-specific code -obj-$(CONFIG_PXA25x) += mfp-pxa2xx.o pxa25x.o -obj-$(CONFIG_PXA27x) += mfp-pxa2xx.o pxa27x.o +obj-$(CONFIG_PXA25x) += mfp-pxa2xx.o pxa2xx.o pxa25x.o +obj-$(CONFIG_PXA27x) += mfp-pxa2xx.o pxa2xx.o pxa27x.o obj-$(CONFIG_PXA3xx) += mfp-pxa3xx.o pxa3xx.o smemc.o obj-$(CONFIG_CPU_PXA300) += pxa300.o obj-$(CONFIG_CPU_PXA320) += pxa320.o +obj-$(CONFIG_CPU_PXA930) += pxa930.o # Specific board support obj-$(CONFIG_ARCH_GUMSTIX) += gumstix.o +obj-$(CONFIG_MACH_AM200EPD) += am200epd.o obj-$(CONFIG_ARCH_LUBBOCK) += lubbock.o obj-$(CONFIG_MACH_LOGICPD_PXA270) += lpd270.o obj-$(CONFIG_MACH_MAINSTONE) += mainstone.o +obj-$(CONFIG_MACH_MP900C) += mp900.o obj-$(CONFIG_ARCH_PXA_IDP) += idp.o obj-$(CONFIG_MACH_TRIZEPS4) += trizeps4.o obj-$(CONFIG_MACH_COLIBRI) += colibri.o -obj-$(CONFIG_PXA_SHARP_C7xx) += corgi.o corgi_ssp.o corgi_lcd.o sharpsl_pm.o corgi_pm.o -obj-$(CONFIG_PXA_SHARP_Cxx00) += spitz.o corgi_ssp.o corgi_lcd.o sharpsl_pm.o spitz_pm.o -obj-$(CONFIG_MACH_AKITA) += akita-ioexp.o -obj-$(CONFIG_MACH_POODLE) += poodle.o corgi_ssp.o +obj-$(CONFIG_PXA_SHARP_C7xx) += corgi.o sharpsl_pm.o corgi_pm.o +obj-$(CONFIG_PXA_SHARP_Cxx00) += spitz.o sharpsl_pm.o spitz_pm.o +obj-$(CONFIG_MACH_POODLE) += poodle.o obj-$(CONFIG_MACH_PCM027) += pcm027.o obj-$(CONFIG_MACH_PCM990_BASEBOARD) += pcm990-baseboard.o obj-$(CONFIG_MACH_TOSA) += tosa.o obj-$(CONFIG_MACH_EM_X270) += em-x270.o obj-$(CONFIG_MACH_MAGICIAN) += magician.o +obj-$(CONFIG_MACH_MIOA701) += mioa701.o mioa701_bootresume.o obj-$(CONFIG_ARCH_PXA_ESERIES) += eseries.o +obj-$(CONFIG_MACH_E330) += e330.o +obj-$(CONFIG_MACH_E350) += e350.o +obj-$(CONFIG_MACH_E740) += e740.o +obj-$(CONFIG_MACH_E750) += e750.o +obj-$(CONFIG_MACH_E400) += e400.o +obj-$(CONFIG_MACH_E800) += e800.o +obj-$(CONFIG_MACH_PALMTX) += palmtx.o +obj-$(CONFIG_MACH_PALMZ72) += palmz72.o +obj-$(CONFIG_ARCH_VIPER) += viper.o ifeq ($(CONFIG_MACH_ZYLONITE),y) obj-y += zylonite.o @@ -43,18 +61,23 @@ ifeq ($(CONFIG_MACH_ZYLONITE),y) obj-$(CONFIG_CPU_PXA320) += zylonite_pxa320.o endif obj-$(CONFIG_MACH_LITTLETON) += littleton.o +obj-$(CONFIG_MACH_TAVOREVB) += tavorevb.o +obj-$(CONFIG_MACH_SAAR) += saar.o -obj-$(CONFIG_MACH_ARMCORE) += cm-x270.o +obj-$(CONFIG_MACH_ARMCORE) += cm-x2xx.o cm-x255.o cm-x270.o +obj-$(CONFIG_MACH_CM_X300) += cm-x300.o +obj-$(CONFIG_PXA_EZX) += ezx.o # Support for blinky lights led-y := leds.o led-$(CONFIG_ARCH_LUBBOCK) += leds-lubbock.o led-$(CONFIG_MACH_MAINSTONE) += leds-mainstone.o led-$(CONFIG_ARCH_PXA_IDP) += leds-idp.o -led-$(CONFIG_MACH_TRIZEPS4) += leds-trizeps4.o obj-$(CONFIG_LEDS) += $(led-y) ifeq ($(CONFIG_PCI),y) -obj-$(CONFIG_MACH_ARMCORE) += cm-x270-pci.o +obj-$(CONFIG_MACH_ARMCORE) += cm-x2xx-pci.o endif + +obj-$(CONFIG_TOSA_BT) += tosa-bt.o diff --git a/arch/arm/mach-pxa/akita-ioexp.c b/arch/arm/mach-pxa/akita-ioexp.c deleted file mode 100644 index 254892ac30c..00000000000 --- a/arch/arm/mach-pxa/akita-ioexp.c +++ /dev/null @@ -1,222 +0,0 @@ -/* - * Support for the Extra GPIOs on the Sharp SL-C1000 (Akita) - * (uses a Maxim MAX7310 8 Port IO Expander) - * - * Copyright 2005 Openedhand Ltd. - * - * Author: Richard Purdie <richard@openedhand.com> - * - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License version 2 as - * published by the Free Software Foundation. - * - */ - -#include <linux/kernel.h> -#include <linux/init.h> -#include <linux/platform_device.h> -#include <linux/module.h> -#include <linux/i2c.h> -#include <linux/slab.h> -#include <linux/workqueue.h> -#include <asm/arch/akita.h> - -/* MAX7310 Regiser Map */ -#define MAX7310_INPUT 0x00 -#define MAX7310_OUTPUT 0x01 -#define MAX7310_POLINV 0x02 -#define MAX7310_IODIR 0x03 /* 1 = Input, 0 = Output */ -#define MAX7310_TIMEOUT 0x04 - -/* Addresses to scan */ -static const unsigned short normal_i2c[] = { 0x18, I2C_CLIENT_END }; - -/* I2C Magic */ -I2C_CLIENT_INSMOD; - -static int max7310_write(struct i2c_client *client, int address, int data); -static struct i2c_client max7310_template; -static void akita_ioexp_work(struct work_struct *private_); - -static struct device *akita_ioexp_device; -static unsigned char ioexp_output_value = AKITA_IOEXP_IO_OUT; -DECLARE_WORK(akita_ioexp, akita_ioexp_work); - - -/* - * MAX7310 Access - */ -static int max7310_config(struct device *dev, int iomode, int polarity) -{ - int ret; - struct i2c_client *client = to_i2c_client(dev); - - ret = max7310_write(client, MAX7310_POLINV, polarity); - if (ret < 0) - return ret; - ret = max7310_write(client, MAX7310_IODIR, iomode); - return ret; -} - -static int max7310_set_ouputs(struct device *dev, int outputs) -{ - struct i2c_client *client = to_i2c_client(dev); - - return max7310_write(client, MAX7310_OUTPUT, outputs); -} - -/* - * I2C Functions - */ -static int max7310_write(struct i2c_client *client, int address, int value) -{ - u8 data[2]; - - data[0] = address & 0xff; - data[1] = value & 0xff; - - if (i2c_master_send(client, data, 2) == 2) - return 0; - return -1; -} - -static int max7310_detect(struct i2c_adapter *adapter, int address, int kind) -{ - struct i2c_client *new_client; - int err; - - if (!(new_client = kmalloc(sizeof(struct i2c_client), GFP_KERNEL))) - return -ENOMEM; - - max7310_template.adapter = adapter; - max7310_template.addr = address; - - memcpy(new_client, &max7310_template, sizeof(struct i2c_client)); - - if ((err = i2c_attach_client(new_client))) { - kfree(new_client); - return err; - } - - max7310_config(&new_client->dev, AKITA_IOEXP_IO_DIR, 0); - akita_ioexp_device = &new_client->dev; - schedule_work(&akita_ioexp); - - return 0; -} - -static int max7310_attach_adapter(struct i2c_adapter *adapter) -{ - return i2c_probe(adapter, &addr_data, max7310_detect); -} - -static int max7310_detach_client(struct i2c_client *client) -{ - int err; - - akita_ioexp_device = NULL; - - if ((err = i2c_detach_client(client))) - return err; - - kfree(client); - return 0; -} - -static struct i2c_driver max7310_i2c_driver = { - .driver = { - .name = "akita-max7310", - }, - .id = I2C_DRIVERID_AKITAIOEXP, - .attach_adapter = max7310_attach_adapter, - .detach_client = max7310_detach_client, -}; - -static struct i2c_client max7310_template = { - name: "akita-max7310", - driver: &max7310_i2c_driver, -}; - -void akita_set_ioexp(struct device *dev, unsigned char bit) -{ - ioexp_output_value |= bit; - - if (akita_ioexp_device) - schedule_work(&akita_ioexp); - return; -} - -void akita_reset_ioexp(struct device *dev, unsigned char bit) -{ - ioexp_output_value &= ~bit; - - if (akita_ioexp_device) - schedule_work(&akita_ioexp); - return; -} - -EXPORT_SYMBOL(akita_set_ioexp); -EXPORT_SYMBOL(akita_reset_ioexp); - -static void akita_ioexp_work(struct work_struct *private_) -{ - if (akita_ioexp_device) - max7310_set_ouputs(akita_ioexp_device, ioexp_output_value); -} - - -#ifdef CONFIG_PM -static int akita_ioexp_suspend(struct platform_device *pdev, pm_message_t state) -{ - flush_scheduled_work(); - return 0; -} - -static int akita_ioexp_resume(struct platform_device *pdev) -{ - schedule_work(&akita_ioexp); - return 0; -} -#else -#define akita_ioexp_suspend NULL -#define akita_ioexp_resume NULL -#endif - -static int __init akita_ioexp_probe(struct platform_device *pdev) -{ - return i2c_add_driver(&max7310_i2c_driver); -} - -static int akita_ioexp_remove(struct platform_device *pdev) -{ - i2c_del_driver(&max7310_i2c_driver); - return 0; -} - -static struct platform_driver akita_ioexp_driver = { - .probe = akita_ioexp_probe, - .remove = akita_ioexp_remove, - .suspend = akita_ioexp_suspend, - .resume = akita_ioexp_resume, - .driver = { - .name = "akita-ioexp", - }, -}; - -static int __init akita_ioexp_init(void) -{ - return platform_driver_register(&akita_ioexp_driver); -} - -static void __exit akita_ioexp_exit(void) -{ - platform_driver_unregister(&akita_ioexp_driver); -} - -MODULE_AUTHOR("Richard Purdie <rpurdie@openedhand.com>"); -MODULE_DESCRIPTION("Akita IO-Expander driver"); -MODULE_LICENSE("GPL"); - -fs_initcall(akita_ioexp_init); -module_exit(akita_ioexp_exit); - diff --git a/arch/arm/mach-pxa/am200epd.c b/arch/arm/mach-pxa/am200epd.c new file mode 100644 index 00000000000..b965085a37b --- /dev/null +++ b/arch/arm/mach-pxa/am200epd.c @@ -0,0 +1,374 @@ +/* + * am200epd.c -- Platform device for AM200 EPD kit + * + * Copyright (C) 2008, Jaya Kumar + * + * This file is subject to the terms and conditions of the GNU General Public + * License. See the file COPYING in the main directory of this archive for + * more details. + * + * Layout is based on skeletonfb.c by James Simmons and Geert Uytterhoeven. + * + * This work was made possible by help and equipment support from E-Ink + * Corporation. http://support.eink.com/community + * + * This driver is written to be used with the Metronome display controller. + * on the AM200 EPD prototype kit/development kit with an E-Ink 800x600 + * Vizplex EPD on a Gumstix board using the Lyre interface board. + * + */ + +#include <linux/module.h> +#include <linux/kernel.h> +#include <linux/errno.h> +#include <linux/string.h> +#include <linux/delay.h> +#include <linux/interrupt.h> +#include <linux/fb.h> +#include <linux/init.h> +#include <linux/platform_device.h> +#include <linux/irq.h> +#include <linux/gpio.h> + +#include <mach/pxafb.h> + +#include <video/metronomefb.h> + +static unsigned int panel_type = 6; +static struct platform_device *am200_device; +static struct metronome_board am200_board; + +static struct pxafb_mode_info am200_fb_mode_9inch7 = { + .pixclock = 40000, + .xres = 1200, + .yres = 842, + .bpp = 16, + .hsync_len = 2, + .left_margin = 2, + .right_margin = 2, + .vsync_len = 1, + .upper_margin = 2, + .lower_margin = 25, + .sync = FB_SYNC_HOR_HIGH_ACT | FB_SYNC_VERT_HIGH_ACT, +}; + +static struct pxafb_mode_info am200_fb_mode_8inch = { + .pixclock = 40000, + .xres = 1088, + .yres = 791, + .bpp = 16, + .hsync_len = 28, + .left_margin = 8, + .right_margin = 30, + .vsync_len = 8, + .upper_margin = 10, + .lower_margin = 8, + .sync = FB_SYNC_HOR_HIGH_ACT | FB_SYNC_VERT_HIGH_ACT, +}; + +static struct pxafb_mode_info am200_fb_mode_6inch = { + .pixclock = 40189, + .xres = 832, + .yres = 622, + .bpp = 16, + .hsync_len = 28, + .left_margin = 34, + .right_margin = 34, + .vsync_len = 25, + .upper_margin = 0, + .lower_margin = 2, + .sync = FB_SYNC_HOR_HIGH_ACT | FB_SYNC_VERT_HIGH_ACT, +}; + +static struct pxafb_mach_info am200_fb_info = { + .modes = &am200_fb_mode_6inch, + .num_modes = 1, + .lcd_conn = LCD_TYPE_COLOR_TFT | LCD_PCLK_EDGE_FALL | + LCD_AC_BIAS_FREQ(24), +}; + +/* register offsets for gpio control */ +#define LED_GPIO_PIN 51 +#define STDBY_GPIO_PIN 48 +#define RST_GPIO_PIN 49 +#define RDY_GPIO_PIN 32 +#define ERR_GPIO_PIN 17 +#define PCBPWR_GPIO_PIN 16 +static int gpios[] = { LED_GPIO_PIN , STDBY_GPIO_PIN , RST_GPIO_PIN, + RDY_GPIO_PIN, ERR_GPIO_PIN, PCBPWR_GPIO_PIN }; +static char *gpio_names[] = { "LED" , "STDBY" , "RST", "RDY", "ERR", "PCBPWR" }; + +static int am200_init_gpio_regs(struct metronomefb_par *par) +{ + int i; + int err; + + for (i = 0; i < ARRAY_SIZE(gpios); i++) { + err = gpio_request(gpios[i], gpio_names[i]); + if (err) { + dev_err(&am200_device->dev, "failed requesting " + "gpio %s, err=%d\n", gpio_names[i], err); + goto err_req_gpio; + } + } + + gpio_direction_output(LED_GPIO_PIN, 0); + gpio_direction_output(STDBY_GPIO_PIN, 0); + gpio_direction_output(RST_GPIO_PIN, 0); + + gpio_direction_input(RDY_GPIO_PIN); + gpio_direction_input(ERR_GPIO_PIN); + + gpio_direction_output(PCBPWR_GPIO_PIN, 0); + + return 0; + +err_req_gpio: + while (i > 0) + gpio_free(gpios[i--]); + + return err; +} + +static void am200_cleanup(struct metronomefb_par *par) +{ + int i; + + free_irq(IRQ_GPIO(RDY_GPIO_PIN), par); + + for (i = 0; i < ARRAY_SIZE(gpios); i++) + gpio_free(gpios[i]); +} + +static int am200_share_video_mem(struct fb_info *info) +{ + /* rough check if this is our desired fb and not something else */ + if ((info->var.xres != am200_fb_info.modes->xres) + || (info->var.yres != am200_fb_info.modes->yres)) + return 0; + + /* we've now been notified that we have our new fb */ + am200_board.metromem = info->screen_base; + am200_board.host_fbinfo = info; + + /* try to refcount host drv since we are the consumer after this */ + if (!try_module_get(info->fbops->owner)) + return -ENODEV; + + return 0; +} + +static int am200_unshare_video_mem(struct fb_info *info) +{ + dev_dbg(&am200_device->dev, "ENTER %s\n", __func__); + + if (info != am200_board.host_fbinfo) + return 0; + + module_put(am200_board.host_fbinfo->fbops->owner); + return 0; +} + +static int am200_fb_notifier_callback(struct notifier_block *self, + unsigned long event, void *data) +{ + struct fb_event *evdata = data; + struct fb_info *info = evdata->info; + + dev_dbg(&am200_device->dev, "ENTER %s\n", __func__); + + if (event == FB_EVENT_FB_REGISTERED) + return am200_share_video_mem(info); + else if (event == FB_EVENT_FB_UNREGISTERED) + return am200_unshare_video_mem(info); + + return 0; +} + +static struct notifier_block am200_fb_notif = { + .notifier_call = am200_fb_notifier_callback, +}; + +/* this gets called as part of our init. these steps must be done now so + * that we can use set_pxa_fb_info */ +static void __init am200_presetup_fb(void) +{ + int fw; + int fh; + int padding_size; + int totalsize; + + switch (panel_type) { + case 6: + am200_fb_info.modes = &am200_fb_mode_6inch; + break; + case 8: + am200_fb_info.modes = &am200_fb_mode_8inch; + break; + case 97: + am200_fb_info.modes = &am200_fb_mode_9inch7; + break; + default: + dev_err(&am200_device->dev, "invalid panel_type selection," + " setting to 6\n"); + am200_fb_info.modes = &am200_fb_mode_6inch; + break; + } + + /* the frame buffer is divided as follows: + command | CRC | padding + 16kb waveform data | CRC | padding + image data | CRC + */ + + fw = am200_fb_info.modes->xres; + fh = am200_fb_info.modes->yres; + + /* waveform must be 16k + 2 for checksum */ + am200_board.wfm_size = roundup(16*1024 + 2, fw); + + padding_size = PAGE_SIZE + (4 * fw); + + /* total is 1 cmd , 1 wfm, padding and image */ + totalsize = fw + am200_board.wfm_size + padding_size + (fw*fh); + + /* save this off because we're manipulating fw after this and + * we'll need it when we're ready to setup the framebuffer */ + am200_board.fw = fw; + am200_board.fh = fh; + + /* the reason we do this adjustment is because we want to acquire + * more framebuffer memory without imposing custom awareness on the + * underlying pxafb driver */ + am200_fb_info.modes->yres = DIV_ROUND_UP(totalsize, fw); + + /* we divide since we told the LCD controller we're 16bpp */ + am200_fb_info.modes->xres /= 2; + + set_pxa_fb_info(&am200_fb_info); + +} + +/* this gets called by metronomefb as part of its init, in our case, we + * have already completed initial framebuffer init in presetup_fb so we + * can just setup the fb access pointers */ +static int am200_setup_fb(struct metronomefb_par *par) +{ + int fw; + int fh; + + fw = am200_board.fw; + fh = am200_board.fh; + + /* metromem was set up by the notifier in share_video_mem so now + * we can use its value to calculate the other entries */ + par->metromem_cmd = (struct metromem_cmd *) am200_board.metromem; + par->metromem_wfm = am200_board.metromem + fw; + par->metromem_img = par->metromem_wfm + am200_board.wfm_size; + par->metromem_img_csum = (u16 *) (par->metromem_img + (fw * fh)); + par->metromem_dma = am200_board.host_fbinfo->fix.smem_start; + + return 0; +} + +static int am200_get_panel_type(void) +{ + return panel_type; +} + +static irqreturn_t am200_handle_irq(int irq, void *dev_id) +{ + struct metronomefb_par *par = dev_id; + + wake_up_interruptible(&par->waitq); + return IRQ_HANDLED; +} + +static int am200_setup_irq(struct fb_info *info) +{ + int ret; + + ret = request_irq(IRQ_GPIO(RDY_GPIO_PIN), am200_handle_irq, + IRQF_DISABLED|IRQF_TRIGGER_FALLING, + "AM200", info->par); + if (ret) + dev_err(&am200_device->dev, "request_irq failed: %d\n", ret); + + return ret; +} + +static void am200_set_rst(struct metronomefb_par *par, int state) +{ + gpio_set_value(RST_GPIO_PIN, state); +} + +static void am200_set_stdby(struct metronomefb_par *par, int state) +{ + gpio_set_value(STDBY_GPIO_PIN, state); +} + +static int am200_wait_event(struct metronomefb_par *par) +{ + return wait_event_timeout(par->waitq, gpio_get_value(RDY_GPIO_PIN), HZ); +} + +static int am200_wait_event_intr(struct metronomefb_par *par) +{ + return wait_event_interruptible_timeout(par->waitq, + gpio_get_value(RDY_GPIO_PIN), HZ); +} + +static struct metronome_board am200_board = { + .owner = THIS_MODULE, + .setup_irq = am200_setup_irq, + .setup_io = am200_init_gpio_regs, + .setup_fb = am200_setup_fb, + .set_rst = am200_set_rst, + .set_stdby = am200_set_stdby, + .met_wait_event = am200_wait_event, + .met_wait_event_intr = am200_wait_event_intr, + .get_panel_type = am200_get_panel_type, + .cleanup = am200_cleanup, +}; + +static int __init am200_init(void) +{ + int ret; + + /* before anything else, we request notification for any fb + * creation events */ + fb_register_client(&am200_fb_notif); + + /* request our platform independent driver */ + request_module("metronomefb"); + + am200_device = platform_device_alloc("metronomefb", -1); + if (!am200_device) + return -ENOMEM; + + /* the am200_board that will be seen by metronomefb is a copy */ + platform_device_add_data(am200_device, &am200_board, + sizeof(am200_board)); + + /* this _add binds metronomefb to am200. metronomefb refcounts am200 */ + ret = platform_device_add(am200_device); + + if (ret) { + platform_device_put(am200_device); + fb_unregister_client(&am200_fb_notif); + return ret; + } + + am200_presetup_fb(); + + return 0; +} + +module_param(panel_type, uint, 0); +MODULE_PARM_DESC(panel_type, "Select the panel type: 6, 8, 97"); + +module_init(am200_init); + +MODULE_DESCRIPTION("board driver for am200 metronome epd kit"); +MODULE_AUTHOR("Jaya Kumar"); +MODULE_LICENSE("GPL"); diff --git a/arch/arm/mach-pxa/clock.c b/arch/arm/mach-pxa/clock.c index e97dc59813c..ca8e2053815 100644 --- a/arch/arm/mach-pxa/clock.c +++ b/arch/arm/mach-pxa/clock.c @@ -12,9 +12,9 @@ #include <linux/platform_device.h> #include <linux/delay.h> -#include <asm/arch/pxa-regs.h> -#include <asm/arch/pxa2xx-gpio.h> -#include <asm/hardware.h> +#include <mach/pxa2xx-regs.h> +#include <mach/pxa2xx-gpio.h> +#include <mach/hardware.h> #include "devices.h" #include "generic.h" @@ -47,6 +47,9 @@ struct clk *clk_get(struct device *dev, const char *id) clk = p; mutex_unlock(&clocks_mutex); + if (!IS_ERR(clk) && clk->ops == NULL) + clk = clk->other; + return clk; } EXPORT_SYMBOL(clk_get); @@ -98,21 +101,6 @@ unsigned long clk_get_rate(struct clk *clk) EXPORT_SYMBOL(clk_get_rate); -static void clk_gpio27_enable(struct clk *clk) -{ - pxa_gpio_mode(GPIO11_3_6MHz_MD); -} - -static void clk_gpio27_disable(struct clk *clk) -{ -} - -static const struct clkops clk_gpio27_ops = { - .enable = clk_gpio27_enable, - .disable = clk_gpio27_disable, -}; - - void clk_cken_enable(struct clk *clk) { CKEN |= 1 << clk->cken; @@ -128,14 +116,6 @@ const struct clkops clk_cken_ops = { .disable = clk_cken_disable, }; -static struct clk common_clks[] = { - { - .name = "GPIO27_CLK", - .ops = &clk_gpio27_ops, - .rate = 3686400, - }, -}; - void clks_register(struct clk *clks, size_t num) { int i; @@ -146,9 +126,27 @@ void clks_register(struct clk *clks, size_t num) mutex_unlock(&clocks_mutex); } -static int __init clk_init(void) +int clk_add_alias(char *alias, struct device *alias_dev, char *id, + struct device *dev) { - clks_register(common_clks, ARRAY_SIZE(common_clks)); + struct clk *r = clk_lookup(dev, id); + struct clk *new; + + if (!r) + return -ENODEV; + + new = kzalloc(sizeof(struct clk), GFP_KERNEL); + + if (!new) + return -ENOMEM; + + new->name = alias; + new->dev = alias_dev; + new->other = r; + + mutex_lock(&clocks_mutex); + list_add(&new->node, &clocks); + mutex_unlock(&clocks_mutex); + return 0; } -arch_initcall(clk_init); diff --git a/arch/arm/mach-pxa/clock.h b/arch/arm/mach-pxa/clock.h index bc6b77e1592..73be795fe3b 100644 --- a/arch/arm/mach-pxa/clock.h +++ b/arch/arm/mach-pxa/clock.h @@ -1,3 +1,5 @@ +#include <linux/list.h> + struct clk; struct clkops { @@ -15,6 +17,7 @@ struct clk { unsigned int cken; unsigned int delay; unsigned int enabled; + struct clk *other; }; #define INIT_CKEN(_name, _cken, _rate, _delay, _dev) \ @@ -35,9 +38,56 @@ struct clk { .cken = CKEN_##_cken, \ } +/* + * This is a placeholder to alias one clock device+name pair + * to another struct clk. + */ +#define INIT_CKOTHER(_name, _other, _dev) \ + { \ + .name = _name, \ + .dev = _dev, \ + .other = _other, \ + } + +#define INIT_CLK(_name, _ops, _rate, _delay, _dev) \ + { \ + .name = _name, \ + .dev = _dev, \ + .ops = _ops, \ + .rate = _rate, \ + .delay = _delay, \ + } + extern const struct clkops clk_cken_ops; void clk_cken_enable(struct clk *clk); void clk_cken_disable(struct clk *clk); +#ifdef CONFIG_PXA3xx +#define PXA3xx_CKEN(_name, _cken, _rate, _delay, _dev) \ + { \ + .name = _name, \ + .dev = _dev, \ + .ops = &clk_pxa3xx_cken_ops, \ + .rate = _rate, \ + .cken = CKEN_##_cken, \ + .delay = _delay, \ + } + +#define PXA3xx_CK(_name, _cken, _ops, _dev) \ + { \ + .name = _name, \ + .dev = _dev, \ + .ops = _ops, \ + .cken = CKEN_##_cken, \ + } + +extern const struct clkops clk_pxa3xx_cken_ops; +extern void clk_pxa3xx_cken_enable(struct clk *); +extern void clk_pxa3xx_cken_disable(struct clk *); +#endif + void clks_register(struct clk *clks, size_t num); +int clk_add_alias(char *alias, struct device *alias_dev, char *id, + struct device *dev); + diff --git a/arch/arm/mach-pxa/cm-x255.c b/arch/arm/mach-pxa/cm-x255.c new file mode 100644 index 00000000000..83a4cdf0817 --- /dev/null +++ b/arch/arm/mach-pxa/cm-x255.c @@ -0,0 +1,258 @@ +/* + * linux/arch/arm/mach-pxa/cm-x255.c + * + * Copyright (C) 2007, 2008 CompuLab, Ltd. + * Mike Rapoport <mike@compulab.co.il> + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ + +#include <linux/platform_device.h> +#include <linux/irq.h> +#include <linux/gpio.h> +#include <linux/mtd/partitions.h> +#include <linux/mtd/physmap.h> +#include <linux/mtd/nand-gpio.h> + +#include <linux/spi/spi.h> + +#include <asm/mach/arch.h> +#include <asm/mach-types.h> +#include <asm/mach/map.h> + +#include <mach/pxa2xx-regs.h> +#include <mach/mfp-pxa25x.h> +#include <mach/pxa2xx_spi.h> +#include <mach/bitfield.h> + +#include "generic.h" + +#define GPIO_NAND_CS (5) +#define GPIO_NAND_ALE (4) +#define GPIO_NAND_CLE (3) +#define GPIO_NAND_RB (10) + +static unsigned long cmx255_pin_config[] = { + /* AC'97 */ + GPIO28_AC97_BITCLK, + GPIO29_AC97_SDATA_IN_0, + GPIO30_AC97_SDATA_OUT, + GPIO31_AC97_SYNC, + + /* BTUART */ + GPIO42_BTUART_RXD, + GPIO43_BTUART_TXD, + GPIO44_BTUART_CTS, + GPIO45_BTUART_RTS, + + /* STUART */ + GPIO46_STUART_RXD, + GPIO47_STUART_TXD, + + /* LCD */ + GPIO58_LCD_LDD_0, + GPIO59_LCD_LDD_1, + GPIO60_LCD_LDD_2, + GPIO61_LCD_LDD_3, + GPIO62_LCD_LDD_4, + GPIO63_LCD_LDD_5, + GPIO64_LCD_LDD_6, + GPIO65_LCD_LDD_7, + GPIO66_LCD_LDD_8, + GPIO67_LCD_LDD_9, + GPIO68_LCD_LDD_10, + GPIO69_LCD_LDD_11, + GPIO70_LCD_LDD_12, + GPIO71_LCD_LDD_13, + GPIO72_LCD_LDD_14, + GPIO73_LCD_LDD_15, + GPIO74_LCD_FCLK, + GPIO75_LCD_LCLK, + GPIO76_LCD_PCLK, + GPIO77_LCD_BIAS, + + /* SSP1 */ + GPIO23_SSP1_SCLK, + GPIO24_SSP1_SFRM, + GPIO25_SSP1_TXD, + GPIO26_SSP1_RXD, + + /* SSP2 */ + GPIO81_SSP2_CLK_OUT, + GPIO82_SSP2_FRM_OUT, + GPIO83_SSP2_TXD, + GPIO84_SSP2_RXD, + + /* PC Card */ + GPIO48_nPOE, + GPIO49_nPWE, + GPIO50_nPIOR, + GPIO51_nPIOW, + GPIO52_nPCE_1, + GPIO53_nPCE_2, + GPIO54_nPSKTSEL, + GPIO55_nPREG, + GPIO56_nPWAIT, + GPIO57_nIOIS16, + + /* SDRAM and local bus */ + GPIO15_nCS_1, + GPIO78_nCS_2, + GPIO79_nCS_3, + GPIO80_nCS_4, + GPIO33_nCS_5, + GPIO18_RDY, + + /* GPIO */ + GPIO0_GPIO | WAKEUP_ON_EDGE_BOTH, + GPIO9_GPIO, /* PC card reset */ + + /* NAND controls */ + GPIO5_GPIO | MFP_LPM_DRIVE_HIGH, /* NAND CE# */ + GPIO4_GPIO | MFP_LPM_DRIVE_LOW, /* NAND ALE */ + GPIO3_GPIO | MFP_LPM_DRIVE_LOW, /* NAND CLE */ + GPIO10_GPIO, /* NAND Ready/Busy */ + + /* interrupts */ + GPIO22_GPIO, /* DM9000 interrupt */ +}; + +#if defined(CONFIG_SPI_PXA2XX) +static struct pxa2xx_spi_master pxa_ssp_master_info = { + .num_chipselect = 1, +}; + +static struct spi_board_info spi_board_info[] __initdata = { + [0] = { + .modalias = "rtc-max6902", + .max_speed_hz = 1000000, + .bus_num = 1, + .chip_select = 0, + }, +}; + +static void __init cmx255_init_rtc(void) +{ + pxa2xx_set_spi_info(1, &pxa_ssp_master_info); + spi_register_board_info(ARRAY_AND_SIZE(spi_board_info)); +} +#else +static inline void cmx255_init_rtc(void) {} +#endif + +#if defined(CONFIG_MTD_PHYSMAP) || defined(CONFIG_MTD_PHYSMAP_MODULE) +static struct mtd_partition cmx255_nor_partitions[] = { + { + .name = "ARMmon", + .size = 0x00030000, + .offset = 0, + .mask_flags = MTD_WRITEABLE /* force read-only */ + } , { + .name = "ARMmon setup block", + .size = 0x00010000, + .offset = MTDPART_OFS_APPEND, + .mask_flags = MTD_WRITEABLE /* force read-only */ + } , { + .name = "kernel", + .size = 0x00160000, + .offset = MTDPART_OFS_APPEND, + } , { + .name = "ramdisk", + .size = MTDPART_SIZ_FULL, + .offset = MTDPART_OFS_APPEND + } +}; + +static struct physmap_flash_data cmx255_nor_flash_data[] = { + { + .width = 2, /* bankwidth in bytes */ + .parts = cmx255_nor_partitions, + .nr_parts = ARRAY_SIZE(cmx255_nor_partitions) + } +}; + +static struct resource cmx255_nor_resource = { + .start = PXA_CS0_PHYS, + .end = PXA_CS0_PHYS + SZ_8M - 1, + .flags = IORESOURCE_MEM, +}; + +static struct platform_device cmx255_nor = { + .name = "physmap-flash", + .id = -1, + .dev = { + .platform_data = cmx255_nor_flash_data, + }, + .resource = &cmx255_nor_resource, + .num_resources = 1, +}; + +static void __init cmx255_init_nor(void) +{ + platform_device_register(&cmx255_nor); +} +#else +static inline void cmx255_init_nor(void) {} +#endif + +#if defined(CONFIG_MTD_NAND_GPIO) || defined(CONFIG_MTD_NAND_GPIO_MODULE) +static struct resource cmx255_nand_resource[] = { + [0] = { + .start = PXA_CS1_PHYS, + .end = PXA_CS1_PHYS + 11, + .flags = IORESOURCE_MEM, + }, + [1] = { + .start = PXA_CS5_PHYS, + .end = PXA_CS5_PHYS + 3, + .flags = IORESOURCE_MEM, + }, +}; + +static struct mtd_partition cmx255_nand_parts[] = { + [0] = { + .name = "cmx255-nand", + .size = MTDPART_SIZ_FULL, + .offset = 0, + }, +}; + +static struct gpio_nand_platdata cmx255_nand_platdata = { + .gpio_nce = GPIO_NAND_CS, + .gpio_cle = GPIO_NAND_CLE, + .gpio_ale = GPIO_NAND_ALE, + .gpio_rdy = GPIO_NAND_RB, + .gpio_nwp = -1, + .parts = cmx255_nand_parts, + .num_parts = ARRAY_SIZE(cmx255_nand_parts), + .chip_delay = 25, +}; + +static struct platform_device cmx255_nand = { + .name = "gpio-nand", + .num_resources = ARRAY_SIZE(cmx255_nand_resource), + .resource = cmx255_nand_resource, + .id = -1, + .dev = { + .platform_data = &cmx255_nand_platdata, + } +}; + +static void __init cmx255_init_nand(void) +{ + platform_device_register(&cmx255_nand); +} +#else +static inline void cmx255_init_nand(void) {} +#endif + +void __init cmx255_init(void) +{ + pxa2xx_mfp_config(ARRAY_AND_SIZE(cmx255_pin_config)); + + cmx255_init_rtc(); + cmx255_init_nor(); + cmx255_init_nand(); +} diff --git a/arch/arm/mach-pxa/cm-x270-pci.h b/arch/arm/mach-pxa/cm-x270-pci.h deleted file mode 100644 index ffe37b66f9a..00000000000 --- a/arch/arm/mach-pxa/cm-x270-pci.h +++ /dev/null @@ -1,13 +0,0 @@ -extern void __cmx270_pci_init_irq(void); -extern void __cmx270_pci_suspend(void); -extern void __cmx270_pci_resume(void); - -#ifdef CONFIG_PCI -#define cmx270_pci_init_irq __cmx270_pci_init_irq -#define cmx270_pci_suspend __cmx270_pci_suspend -#define cmx270_pci_resume __cmx270_pci_resume -#else -#define cmx270_pci_init_irq() do {} while (0) -#define cmx270_pci_suspend() do {} while (0) -#define cmx270_pci_resume() do {} while (0) -#endif diff --git a/arch/arm/mach-pxa/cm-x270.c b/arch/arm/mach-pxa/cm-x270.c index f5851d1adc2..a82dad1a8cc 100644 --- a/arch/arm/mach-pxa/cm-x270.c +++ b/arch/arm/mach-pxa/cm-x270.c @@ -1,7 +1,7 @@ /* * linux/arch/arm/mach-pxa/cm-x270.c * - * Copyright (C) 2007 CompuLab, Ltd. + * Copyright (C) 2007, 2008 CompuLab, Ltd. * Mike Rapoport <mike@compulab.co.il> * * This program is free software; you can redistribute it and/or modify @@ -9,91 +9,132 @@ * published by the Free Software Foundation. */ -#include <linux/types.h> -#include <linux/pm.h> -#include <linux/fb.h> #include <linux/platform_device.h> -#include <linux/irq.h> #include <linux/sysdev.h> -#include <linux/io.h> -#include <linux/delay.h> +#include <linux/irq.h> +#include <linux/gpio.h> -#include <linux/dm9000.h> #include <linux/rtc-v3020.h> -#include <linux/serial_8250.h> - #include <video/mbxfb.h> -#include <asm/mach/arch.h> -#include <asm/mach-types.h> -#include <asm/mach/map.h> - -#include <asm/arch/pxa-regs.h> -#include <asm/arch/pxa2xx-regs.h> -#include <asm/arch/pxa2xx-gpio.h> -#include <asm/arch/pxafb.h> -#include <asm/arch/ohci.h> -#include <asm/arch/mmc.h> -#include <asm/arch/bitfield.h> -#include <asm/arch/cm-x270.h> - -#include <asm/hardware/it8152.h> +#include <mach/mfp-pxa27x.h> +#include <mach/ohci.h> +#include <mach/mmc.h> #include "generic.h" -#include "cm-x270-pci.h" +/* physical address if local-bus attached devices */ #define RTC_PHYS_BASE (PXA_CS1_PHYS + (5 << 22)) -#define DM9000_PHYS_BASE (PXA_CS1_PHYS + (6 << 22)) - -static struct resource cmx270_dm9k_resource[] = { - [0] = { - .start = DM9000_PHYS_BASE, - .end = DM9000_PHYS_BASE + 4, - .flags = IORESOURCE_MEM, - }, - [1] = { - .start = DM9000_PHYS_BASE + 8, - .end = DM9000_PHYS_BASE + 8 + 500, - .flags = IORESOURCE_MEM, - }, - [2] = { - .start = CMX270_ETHIRQ, - .end = CMX270_ETHIRQ, - .flags = IORESOURCE_IRQ | IORESOURCE_IRQ_HIGHEDGE, - } -}; -/* for the moment we limit ourselves to 32bit IO until some - * better IO routines can be written and tested - */ -static struct dm9000_plat_data cmx270_dm9k_platdata = { - .flags = DM9000_PLATF_32BITONLY, +/* GPIO IRQ usage */ +#define GPIO83_MMC_IRQ (83) + +#define CMX270_MMC_IRQ IRQ_GPIO(GPIO83_MMC_IRQ) + +/* MMC power enable */ +#define GPIO105_MMC_POWER (105) + +static unsigned long cmx270_pin_config[] = { + /* AC'97 */ + GPIO28_AC97_BITCLK, + GPIO29_AC97_SDATA_IN_0, + GPIO30_AC97_SDATA_OUT, + GPIO31_AC97_SYNC, + GPIO98_AC97_SYSCLK, + GPIO113_AC97_nRESET, + + /* BTUART */ + GPIO42_BTUART_RXD, + GPIO43_BTUART_TXD, + GPIO44_BTUART_CTS, + GPIO45_BTUART_RTS, + + /* STUART */ + GPIO46_STUART_RXD, + GPIO47_STUART_TXD, + + /* MCI controller */ + GPIO32_MMC_CLK, + GPIO112_MMC_CMD, + GPIO92_MMC_DAT_0, + GPIO109_MMC_DAT_1, + GPIO110_MMC_DAT_2, + GPIO111_MMC_DAT_3, + + /* LCD */ + GPIO58_LCD_LDD_0, + GPIO59_LCD_LDD_1, + GPIO60_LCD_LDD_2, + GPIO61_LCD_LDD_3, + GPIO62_LCD_LDD_4, + GPIO63_LCD_LDD_5, + GPIO64_LCD_LDD_6, + GPIO65_LCD_LDD_7, + GPIO66_LCD_LDD_8, + GPIO67_LCD_LDD_9, + GPIO68_LCD_LDD_10, + GPIO69_LCD_LDD_11, + GPIO70_LCD_LDD_12, + GPIO71_LCD_LDD_13, + GPIO72_LCD_LDD_14, + GPIO73_LCD_LDD_15, + GPIO74_LCD_FCLK, + GPIO75_LCD_LCLK, + GPIO76_LCD_PCLK, + GPIO77_LCD_BIAS, + + /* I2C */ + GPIO117_I2C_SCL, + GPIO118_I2C_SDA, + + /* SSP1 */ + GPIO23_SSP1_SCLK, + GPIO24_SSP1_SFRM, + GPIO25_SSP1_TXD, + GPIO26_SSP1_RXD, + + /* SSP2 */ + GPIO19_SSP2_SCLK, + GPIO14_SSP2_SFRM, + GPIO87_SSP2_TXD, + GPIO88_SSP2_RXD, + + /* PC Card */ + GPIO48_nPOE, + GPIO49_nPWE, + GPIO50_nPIOR, + GPIO51_nPIOW, + GPIO85_nPCE_1, + GPIO54_nPCE_2, + GPIO55_nPREG, + GPIO56_nPWAIT, + GPIO57_nIOIS16, + + /* SDRAM and local bus */ + GPIO15_nCS_1, + GPIO78_nCS_2, + GPIO79_nCS_3, + GPIO80_nCS_4, + GPIO33_nCS_5, + GPIO49_nPWE, + GPIO18_RDY, + + /* GPIO */ + GPIO0_GPIO | WAKEUP_ON_EDGE_BOTH, + GPIO105_GPIO | MFP_LPM_DRIVE_HIGH, /* MMC/SD power */ + GPIO53_GPIO, /* PC card reset */ + + /* NAND controls */ + GPIO11_GPIO | MFP_LPM_DRIVE_HIGH, /* NAND CE# */ + GPIO89_GPIO, /* NAND Ready/Busy */ + + /* interrupts */ + GPIO10_GPIO, /* DM9000 interrupt */ + GPIO83_GPIO, /* MMC card detect */ }; -/* Ethernet device */ -static struct platform_device cmx270_device_dm9k = { - .name = "dm9000", - .id = 0, - .num_resources = ARRAY_SIZE(cmx270_dm9k_resource), - .resource = cmx270_dm9k_resource, - .dev = { - .platform_data = &cmx270_dm9k_platdata, - } -}; - -/* audio device */ -static struct platform_device cmx270_audio_device = { - .name = "pxa2xx-ac97", - .id = -1, -}; - -/* touchscreen controller */ -static struct platform_device cmx270_ts_device = { - .name = "ucb1400_ts", - .id = -1, -}; - -/* RTC */ +/* V3020 RTC */ +#if defined(CONFIG_RTC_DRV_V3020) || defined(CONFIG_RTC_DRV_V3020_MODULE) static struct resource cmx270_v3020_resource[] = { [0] = { .start = RTC_PHYS_BASE, @@ -116,28 +157,29 @@ static struct platform_device cmx270_rtc_device = { } }; -/* - * CM-X270 LEDs - */ -static struct platform_device cmx270_led_device = { - .name = "cm-x270-led", - .id = -1, -}; +static void __init cmx270_init_rtc(void) +{ + platform_device_register(&cmx270_rtc_device); +} +#else +static inline void cmx2xx_init_rtc(void) {} +#endif /* 2700G graphics */ +#if defined(CONFIG_FB_MBX) || defined(CONFIG_FB_MBX_MODULE) static u64 fb_dma_mask = ~(u64)0; static struct resource cmx270_2700G_resource[] = { /* frame buffer memory including ODFB and External SDRAM */ [0] = { - .start = MARATHON_PHYS, - .end = MARATHON_PHYS + 0x02000000, + .start = PXA_CS2_PHYS, + .end = PXA_CS2_PHYS + 0x01ffffff, .flags = IORESOURCE_MEM, }, /* Marathon registers */ [1] = { - .start = MARATHON_PHYS + 0x03fe0000, - .end = MARATHON_PHYS + 0x03ffffff, + .start = PXA_CS2_PHYS + 0x03fe0000, + .end = PXA_CS2_PHYS + 0x03ffffff, .flags = IORESOURCE_MEM, }, }; @@ -205,297 +247,52 @@ static struct platform_device cmx270_2700G = { .id = -1, }; -static u64 ata_dma_mask = ~(u64)0; - -static struct platform_device cmx270_ata = { - .name = "pata_cm_x270", - .id = -1, - .dev = { - .dma_mask = &ata_dma_mask, - .coherent_dma_mask = 0xffffffff, - }, -}; - -/* platform devices */ -static struct platform_device *platform_devices[] __initdata = { - &cmx270_device_dm9k, - &cmx270_audio_device, - &cmx270_rtc_device, - &cmx270_2700G, - &cmx270_led_device, - &cmx270_ts_device, - &cmx270_ata, -}; - -/* Map PCI companion and IDE/General Purpose CS statically */ -static struct map_desc cmx270_io_desc[] __initdata = { - [0] = { /* IDE/general purpose space */ - .virtual = CMX270_IDE104_VIRT, - .pfn = __phys_to_pfn(CMX270_IDE104_PHYS), - .length = SZ_64M - SZ_8M, - .type = MT_DEVICE - }, - [1] = { /* PCI bridge */ - .virtual = CMX270_IT8152_VIRT, - .pfn = __phys_to_pfn(CMX270_IT8152_PHYS), - .length = SZ_64M, - .type = MT_DEVICE - }, -}; - -/* - Display definitions - keep these for backwards compatibility, although symbolic names (as - e.g. in lpd270.c) looks better -*/ -#define MTYPE_STN320x240 0 -#define MTYPE_TFT640x480 1 -#define MTYPE_CRT640x480 2 -#define MTYPE_CRT800x600 3 -#define MTYPE_TFT320x240 6 -#define MTYPE_STN640x480 7 - -static struct pxafb_mode_info generic_stn_320x240_mode = { - .pixclock = 76923, - .bpp = 8, - .xres = 320, - .yres = 240, - .hsync_len = 3, - .vsync_len = 2, - .left_margin = 3, - .upper_margin = 0, - .right_margin = 3, - .lower_margin = 0, - .sync = (FB_SYNC_HOR_HIGH_ACT | - FB_SYNC_VERT_HIGH_ACT), - .cmap_greyscale = 0, -}; - -static struct pxafb_mach_info generic_stn_320x240 = { - .modes = &generic_stn_320x240_mode, - .num_modes = 1, - .lccr0 = 0, - .lccr3 = (LCCR3_PixClkDiv(0x03) | - LCCR3_Acb(0xff) | - LCCR3_PCP), - .cmap_inverse = 0, - .cmap_static = 0, -}; - -static struct pxafb_mode_info generic_tft_640x480_mode = { - .pixclock = 38461, - .bpp = 8, - .xres = 640, - .yres = 480, - .hsync_len = 60, - .vsync_len = 2, - .left_margin = 70, - .upper_margin = 10, - .right_margin = 70, - .lower_margin = 5, - .sync = 0, - .cmap_greyscale = 0, -}; - -static struct pxafb_mach_info generic_tft_640x480 = { - .modes = &generic_tft_640x480_mode, - .num_modes = 1, - .lccr0 = (LCCR0_PAS), - .lccr3 = (LCCR3_PixClkDiv(0x01) | - LCCR3_Acb(0xff) | - LCCR3_PCP), - .cmap_inverse = 0, - .cmap_static = 0, -}; - -static struct pxafb_mode_info generic_crt_640x480_mode = { - .pixclock = 38461, - .bpp = 8, - .xres = 640, - .yres = 480, - .hsync_len = 63, - .vsync_len = 2, - .left_margin = 81, - .upper_margin = 33, - .right_margin = 16, - .lower_margin = 10, - .sync = (FB_SYNC_HOR_HIGH_ACT | - FB_SYNC_VERT_HIGH_ACT), - .cmap_greyscale = 0, -}; - -static struct pxafb_mach_info generic_crt_640x480 = { - .modes = &generic_crt_640x480_mode, - .num_modes = 1, - .lccr0 = (LCCR0_PAS), - .lccr3 = (LCCR3_PixClkDiv(0x01) | - LCCR3_Acb(0xff)), - .cmap_inverse = 0, - .cmap_static = 0, -}; - -static struct pxafb_mode_info generic_crt_800x600_mode = { - .pixclock = 28846, - .bpp = 8, - .xres = 800, - .yres = 600, - .hsync_len = 63, - .vsync_len = 2, - .left_margin = 26, - .upper_margin = 21, - .right_margin = 26, - .lower_margin = 11, - .sync = (FB_SYNC_HOR_HIGH_ACT | - FB_SYNC_VERT_HIGH_ACT), - .cmap_greyscale = 0, -}; - -static struct pxafb_mach_info generic_crt_800x600 = { - .modes = &generic_crt_800x600_mode, - .num_modes = 1, - .lccr0 = (LCCR0_PAS), - .lccr3 = (LCCR3_PixClkDiv(0x02) | - LCCR3_Acb(0xff)), - .cmap_inverse = 0, - .cmap_static = 0, -}; - -static struct pxafb_mode_info generic_tft_320x240_mode = { - .pixclock = 134615, - .bpp = 16, - .xres = 320, - .yres = 240, - .hsync_len = 63, - .vsync_len = 7, - .left_margin = 75, - .upper_margin = 0, - .right_margin = 15, - .lower_margin = 15, - .sync = 0, - .cmap_greyscale = 0, -}; - -static struct pxafb_mach_info generic_tft_320x240 = { - .modes = &generic_tft_320x240_mode, - .num_modes = 1, - .lccr0 = (LCCR0_PAS), - .lccr3 = (LCCR3_PixClkDiv(0x06) | - LCCR3_Acb(0xff) | - LCCR3_PCP), - .cmap_inverse = 0, - .cmap_static = 0, -}; - -static struct pxafb_mode_info generic_stn_640x480_mode = { - .pixclock = 57692, - .bpp = 8, - .xres = 640, - .yres = 480, - .hsync_len = 4, - .vsync_len = 2, - .left_margin = 10, - .upper_margin = 5, - .right_margin = 10, - .lower_margin = 5, - .sync = (FB_SYNC_HOR_HIGH_ACT | - FB_SYNC_VERT_HIGH_ACT), - .cmap_greyscale = 0, -}; - -static struct pxafb_mach_info generic_stn_640x480 = { - .modes = &generic_stn_640x480_mode, - .num_modes = 1, - .lccr0 = 0, - .lccr3 = (LCCR3_PixClkDiv(0x02) | - LCCR3_Acb(0xff)), - .cmap_inverse = 0, - .cmap_static = 0, -}; - -static struct pxafb_mach_info *cmx270_display = &generic_crt_640x480; - -static int __init cmx270_set_display(char *str) +static void __init cmx270_init_2700G(void) { - int disp_type = simple_strtol(str, NULL, 0); - switch (disp_type) { - case MTYPE_STN320x240: - cmx270_display = &generic_stn_320x240; - break; - case MTYPE_TFT640x480: - cmx270_display = &generic_tft_640x480; - break; - case MTYPE_CRT640x480: - cmx270_display = &generic_crt_640x480; - break; - case MTYPE_CRT800x600: - cmx270_display = &generic_crt_800x600; - break; - case MTYPE_TFT320x240: - cmx270_display = &generic_tft_320x240; - break; - case MTYPE_STN640x480: - cmx270_display = &generic_stn_640x480; - break; - default: /* fallback to CRT 640x480 */ - cmx270_display = &generic_crt_640x480; - break; - } - return 1; + platform_device_register(&cmx270_2700G); } - -/* - This should be done really early to get proper configuration for - frame buffer. - Indeed, pxafb parameters can be used istead, but CM-X270 bootloader - has limitied line length for kernel command line, and also it will - break compatibitlty with proprietary releases already in field. -*/ -__setup("monitor=", cmx270_set_display); +#else +static inline void cmx270_init_2700G(void) {} +#endif /* PXA27x OHCI controller setup */ -static int cmx270_ohci_init(struct device *dev) -{ - /* Set the Power Control Polarity Low */ - UHCHR = (UHCHR | UHCHR_PCPL) & - ~(UHCHR_SSEP1 | UHCHR_SSEP2 | UHCHR_SSE); - - return 0; -} - +#if defined(CONFIG_USB_OHCI_HCD) || defined(CONFIG_USB_OHCI_HCD_MODULE) static struct pxaohci_platform_data cmx270_ohci_platform_data = { .port_mode = PMM_PERPORT_MODE, - .init = cmx270_ohci_init, + .flags = ENABLE_PORT1 | ENABLE_PORT2 | POWER_CONTROL_LOW, }; +static void __init cmx270_init_ohci(void) +{ + pxa_set_ohci_info(&cmx270_ohci_platform_data); +} +#else +static inline void cmx270_init_ohci(void) {} +#endif +#if defined(CONFIG_MMC) || defined(CONFIG_MMC_MODULE) static int cmx270_mci_init(struct device *dev, irq_handler_t cmx270_detect_int, void *data) { int err; - /* - * setup GPIO for PXA27x MMC controller - */ - pxa_gpio_mode(GPIO32_MMCCLK_MD); - pxa_gpio_mode(GPIO112_MMCCMD_MD); - pxa_gpio_mode(GPIO92_MMCDAT0_MD); - pxa_gpio_mode(GPIO109_MMCDAT1_MD); - pxa_gpio_mode(GPIO110_MMCDAT2_MD); - pxa_gpio_mode(GPIO111_MMCDAT3_MD); - - /* SB-X270 uses GPIO105 as SD power enable */ - pxa_gpio_mode(105 | GPIO_OUT); + err = gpio_request(GPIO105_MMC_POWER, "MMC/SD power"); + if (err) { + dev_warn(dev, "power gpio unavailable\n"); + return err; + } - /* card detect IRQ on GPIO 83 */ - pxa_gpio_mode(IRQ_TO_GPIO(CMX270_MMC_IRQ)); + gpio_direction_output(GPIO105_MMC_POWER, 0); err = request_irq(CMX270_MMC_IRQ, cmx270_detect_int, IRQF_DISABLED | IRQF_TRIGGER_FALLING, "MMC card detect", data); - if (err) - printk(KERN_ERR "cmx270_mci_init: MMC/SD: can't" - " request MMC card detect IRQ\n"); + if (err) { + gpio_free(GPIO105_MMC_POWER); + dev_err(dev, "cmx270_mci_init: MMC/SD: can't" + " request MMC card detect IRQ\n"); + } return err; } @@ -505,17 +302,18 @@ static void cmx270_mci_setpower(struct device *dev, unsigned int vdd) struct pxamci_platform_data *p_d = dev->platform_data; if ((1 << vdd) & p_d->ocr_mask) { - printk(KERN_DEBUG "%s: on\n", __func__); - GPCR(105) = GPIO_bit(105); + dev_dbg(dev, "power on\n"); + gpio_set_value(GPIO105_MMC_POWER, 0); } else { - GPSR(105) = GPIO_bit(105); - printk(KERN_DEBUG "%s: off\n", __func__); + gpio_set_value(GPIO105_MMC_POWER, 1); + dev_dbg(dev, "power off\n"); } } static void cmx270_mci_exit(struct device *dev, void *data) { free_irq(CMX270_MMC_IRQ, data); + gpio_free(GPIO105_MMC_POWER); } static struct pxamci_platform_data cmx270_mci_platform_data = { @@ -525,120 +323,20 @@ static struct pxamci_platform_data cmx270_mci_platform_data = { .exit = cmx270_mci_exit, }; -#ifdef CONFIG_PM -static unsigned long sleep_save_msc[10]; - -static int cmx270_suspend(struct sys_device *dev, pm_message_t state) -{ - cmx270_pci_suspend(); - - /* save MSC registers */ - sleep_save_msc[0] = MSC0; - sleep_save_msc[1] = MSC1; - sleep_save_msc[2] = MSC2; - - /* setup power saving mode registers */ - PCFR = 0x0; - PSLR = 0xff400000; - PMCR = 0x00000005; - PWER = 0x80000000; - PFER = 0x00000000; - PRER = 0x00000000; - PGSR0 = 0xC0018800; - PGSR1 = 0x004F0002; - PGSR2 = 0x6021C000; - PGSR3 = 0x00020000; - - return 0; -} - -static int cmx270_resume(struct sys_device *dev) -{ - cmx270_pci_resume(); - - /* restore MSC registers */ - MSC0 = sleep_save_msc[0]; - MSC1 = sleep_save_msc[1]; - MSC2 = sleep_save_msc[2]; - - return 0; -} - -static struct sysdev_class cmx270_pm_sysclass = { - .name = "pm", - .resume = cmx270_resume, - .suspend = cmx270_suspend, -}; - -static struct sys_device cmx270_pm_device = { - .cls = &cmx270_pm_sysclass, -}; - -static int __init cmx270_pm_init(void) +static void __init cmx270_init_mmc(void) { - int error; - error = sysdev_class_register(&cmx270_pm_sysclass); - if (error == 0) - error = sysdev_register(&cmx270_pm_device); - return error; + pxa_set_mci_info(&cmx270_mci_platform_data); } #else -static int __init cmx270_pm_init(void) { return 0; } +static inline void cmx270_init_mmc(void) {} #endif -static void __init cmx270_init(void) +void __init cmx270_init(void) { - cmx270_pm_init(); - - set_pxa_fb_info(cmx270_display); + pxa2xx_mfp_config(ARRAY_AND_SIZE(cmx270_pin_config)); - /* register CM-X270 platform devices */ - platform_add_devices(platform_devices, ARRAY_SIZE(platform_devices)); - - /* set MCI and OHCI platform parameters */ - pxa_set_mci_info(&cmx270_mci_platform_data); - pxa_set_ohci_info(&cmx270_ohci_platform_data); - - /* This enables the STUART */ - pxa_gpio_mode(GPIO46_STRXD_MD); - pxa_gpio_mode(GPIO47_STTXD_MD); - - /* This enables the BTUART */ - pxa_gpio_mode(GPIO42_BTRXD_MD); - pxa_gpio_mode(GPIO43_BTTXD_MD); - pxa_gpio_mode(GPIO44_BTCTS_MD); - pxa_gpio_mode(GPIO45_BTRTS_MD); + cmx270_init_rtc(); + cmx270_init_mmc(); + cmx270_init_ohci(); + cmx270_init_2700G(); } - -static void __init cmx270_init_irq(void) -{ - pxa27x_init_irq(); - - - cmx270_pci_init_irq(); - - /* Setup interrupt for dm9000 */ - pxa_gpio_mode(IRQ_TO_GPIO(CMX270_ETHIRQ)); - set_irq_type(CMX270_ETHIRQ, IRQT_RISING); - - /* Setup interrupt for 2700G */ - pxa_gpio_mode(IRQ_TO_GPIO(CMX270_GFXIRQ)); - set_irq_type(CMX270_GFXIRQ, IRQT_FALLING); -} - -static void __init cmx270_map_io(void) -{ - pxa_map_io(); - iotable_init(cmx270_io_desc, ARRAY_SIZE(cmx270_io_desc)); -} - - -MACHINE_START(ARMCORE, "Compulab CM-x270") - .boot_params = 0xa0000100, - .phys_io = 0x40000000, - .io_pg_offst = (io_p2v(0x40000000) >> 18) & 0xfffc, - .map_io = cmx270_map_io, - .init_irq = cmx270_init_irq, - .timer = &pxa_timer, - .init_machine = cmx270_init, -MACHINE_END diff --git a/arch/arm/mach-pxa/cm-x270-pci.c b/arch/arm/mach-pxa/cm-x2xx-pci.c index ac7f05f9f3e..3156b25f6e9 100644 --- a/arch/arm/mach-pxa/cm-x270-pci.c +++ b/arch/arm/mach-pxa/cm-x2xx-pci.c @@ -1,11 +1,11 @@ /* - * linux/arch/arm/mach-pxa/cm-x270-pci.c + * linux/arch/arm/mach-pxa/cm-x2xx-pci.c * * PCI bios-type initialisation for PCI machines * * Bits taken from various places. * - * Copyright (C) 2007 Compulab, Ltd. + * Copyright (C) 2007, 2008 Compulab, Ltd. * Mike Rapoport <mike@compulab.co.il> * * This program is free software; you can redistribute it and/or modify @@ -19,16 +19,16 @@ #include <linux/device.h> #include <linux/platform_device.h> #include <linux/irq.h> +#include <linux/gpio.h> #include <asm/mach/pci.h> -#include <asm/arch/cm-x270.h> -#include <asm/arch/pxa-regs.h> -#include <asm/arch/pxa2xx-gpio.h> +#include <mach/pxa-regs.h> #include <asm/mach-types.h> #include <asm/hardware/it8152.h> -unsigned long it8152_base_address = CMX270_IT8152_VIRT; +unsigned long it8152_base_address; +static int cmx2xx_it8152_irq_gpio; /* * Only first 64MB of memory can be accessed via PCI. @@ -36,47 +36,50 @@ unsigned long it8152_base_address = CMX270_IT8152_VIRT; * This is really ugly and we need a better way of specifying * DMA-capable regions of memory. */ -void __init cmx270_pci_adjust_zones(int node, unsigned long *zone_size, +void __init cmx2xx_pci_adjust_zones(int node, unsigned long *zone_size, unsigned long *zhole_size) { unsigned int sz = SZ_64M >> PAGE_SHIFT; - pr_info("Adjusting zones for CM-x270\n"); + if (machine_is_armcore()) { + pr_info("Adjusting zones for CM-X2XX\n"); - /* - * Only adjust if > 64M on current system - */ - if (node || (zone_size[0] <= sz)) - return; - - zone_size[1] = zone_size[0] - sz; - zone_size[0] = sz; - zhole_size[1] = zhole_size[0]; - zhole_size[0] = 0; + /* + * Only adjust if > 64M on current system + */ + if (node || (zone_size[0] <= sz)) + return; + + zone_size[1] = zone_size[0] - sz; + zone_size[0] = sz; + zhole_size[1] = zhole_size[0]; + zhole_size[0] = 0; + } } -static void cmx270_it8152_irq_demux(unsigned int irq, struct irq_desc *desc) +static void cmx2xx_it8152_irq_demux(unsigned int irq, struct irq_desc *desc) { /* clear our parent irq */ - GEDR(GPIO_IT8152_IRQ) = GPIO_bit(GPIO_IT8152_IRQ); + GEDR(cmx2xx_it8152_irq_gpio) = GPIO_bit(cmx2xx_it8152_irq_gpio); it8152_irq_demux(irq, desc); } -void __cmx270_pci_init_irq(void) +void __cmx2xx_pci_init_irq(int irq_gpio) { it8152_init_irq(); - pxa_gpio_mode(IRQ_TO_GPIO(GPIO_IT8152_IRQ)); - set_irq_type(IRQ_GPIO(GPIO_IT8152_IRQ), IRQT_RISING); - set_irq_chained_handler(IRQ_GPIO(GPIO_IT8152_IRQ), - cmx270_it8152_irq_demux); + cmx2xx_it8152_irq_gpio = irq_gpio; + + set_irq_type(gpio_to_irq(irq_gpio), IRQ_TYPE_EDGE_RISING); + + set_irq_chained_handler(gpio_to_irq(irq_gpio), cmx2xx_it8152_irq_demux); } #ifdef CONFIG_PM static unsigned long sleep_save_ite[10]; -void __cmx270_pci_suspend(void) +void __cmx2xx_pci_suspend(void) { /* save ITE state */ sleep_save_ite[0] = __raw_readl(IT8152_INTC_PDCNIMR); @@ -88,7 +91,7 @@ void __cmx270_pci_suspend(void) __raw_writel((0), IT8152_INTC_LPCNIRR); } -void __cmx270_pci_resume(void) +void __cmx2xx_pci_resume(void) { /* restore IT8152 state */ __raw_writel((sleep_save_ite[0]), IT8152_INTC_PDCNIMR); @@ -96,12 +99,12 @@ void __cmx270_pci_resume(void) __raw_writel((sleep_save_ite[2]), IT8152_INTC_LPNIAR); } #else -void cmx270_pci_suspend(void) {} -void cmx270_pci_resume(void) {} +void cmx2xx_pci_suspend(void) {} +void cmx2xx_pci_resume(void) {} #endif /* PCI IRQ mapping*/ -static int __init cmx270_pci_map_irq(struct pci_dev *dev, u8 slot, u8 pin) +static int __init cmx2xx_pci_map_irq(struct pci_dev *dev, u8 slot, u8 pin) { int irq; @@ -113,14 +116,14 @@ static int __init cmx270_pci_map_irq(struct pci_dev *dev, u8 slot, u8 pin) /* Here comes the ugly part. The routing is baseboard specific, - but defining a platform for each possible base of CM-x270 is - unrealistic. Here we keep mapping for ATXBase and SB-x270. + but defining a platform for each possible base of CM-X2XX is + unrealistic. Here we keep mapping for ATXBase and SB-X2XX. */ /* ATXBASE PCI slot */ if (slot == 7) return IT8152_PCI_INTA; - /* ATXBase/SB-x270 CardBus */ + /* ATXBase/SB-X2XX CardBus */ if (slot == 8 || slot == 0) return IT8152_PCI_INTB; @@ -128,7 +131,11 @@ static int __init cmx270_pci_map_irq(struct pci_dev *dev, u8 slot, u8 pin) if (slot == 9) return IT8152_PCI_INTA; - /* SB-x270 Ethernet */ + /* CM-x255 Onboard Ethernet */ + if (slot == 15) + return IT8152_PCI_INTC; + + /* SB-x2xx Ethernet */ if (slot == 16) return IT8152_PCI_INTA; @@ -141,9 +148,9 @@ static int __init cmx270_pci_map_irq(struct pci_dev *dev, u8 slot, u8 pin) return(0); } -static void cmx270_pci_preinit(void) +static void cmx2xx_pci_preinit(void) { - pr_info("Initializing CM-X270 PCI subsystem\n"); + pr_info("Initializing CM-X2XX PCI subsystem\n"); __raw_writel(0x800, IT8152_PCI_CFG_ADDR); if (__raw_readl(IT8152_PCI_CFG_DATA) == 0x81521283) { @@ -197,21 +204,21 @@ static void cmx270_pci_preinit(void) } } -static struct hw_pci cmx270_pci __initdata = { +static struct hw_pci cmx2xx_pci __initdata = { .swizzle = pci_std_swizzle, - .map_irq = cmx270_pci_map_irq, + .map_irq = cmx2xx_pci_map_irq, .nr_controllers = 1, .setup = it8152_pci_setup, .scan = it8152_pci_scan_bus, - .preinit = cmx270_pci_preinit, + .preinit = cmx2xx_pci_preinit, }; -static int __init cmx270_init_pci(void) +static int __init cmx2xx_init_pci(void) { if (machine_is_armcore()) - pci_common_init(&cmx270_pci); + pci_common_init(&cmx2xx_pci); return 0; } -subsys_initcall(cmx270_init_pci); +subsys_initcall(cmx2xx_init_pci); diff --git a/arch/arm/mach-pxa/cm-x2xx-pci.h b/arch/arm/mach-pxa/cm-x2xx-pci.h new file mode 100644 index 00000000000..e24aad2e3ad --- /dev/null +++ b/arch/arm/mach-pxa/cm-x2xx-pci.h @@ -0,0 +1,13 @@ +extern void __cmx2xx_pci_init_irq(int irq_gpio); +extern void __cmx2xx_pci_suspend(void); +extern void __cmx2xx_pci_resume(void); + +#ifdef CONFIG_PCI +#define cmx2xx_pci_init_irq(x) __cmx2xx_pci_init_irq(x) +#define cmx2xx_pci_suspend(x) __cmx2xx_pci_suspend(x) +#define cmx2xx_pci_resume(x) __cmx2xx_pci_resume(x) +#else +#define cmx2xx_pci_init_irq(x) do {} while (0) +#define cmx2xx_pci_suspend(x) do {} while (0) +#define cmx2xx_pci_resume(x) do {} while (0) +#endif diff --git a/arch/arm/mach-pxa/cm-x2xx.c b/arch/arm/mach-pxa/cm-x2xx.c new file mode 100644 index 00000000000..0b3ce3b6d89 --- /dev/null +++ b/arch/arm/mach-pxa/cm-x2xx.c @@ -0,0 +1,531 @@ +/* + * linux/arch/arm/mach-pxa/cm-x2xx.c + * + * Copyright (C) 2008 CompuLab, Ltd. + * Mike Rapoport <mike@compulab.co.il> + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ + +#include <linux/platform_device.h> +#include <linux/sysdev.h> +#include <linux/irq.h> +#include <linux/gpio.h> + +#include <linux/dm9000.h> +#include <linux/leds.h> + +#include <asm/mach/arch.h> +#include <asm/mach-types.h> +#include <asm/mach/map.h> + +#include <mach/pxa2xx-regs.h> +#include <mach/mfp-pxa27x.h> +#include <mach/pxa-regs.h> +#include <mach/audio.h> +#include <mach/pxafb.h> + +#include <asm/hardware/it8152.h> + +#include "generic.h" +#include "cm-x2xx-pci.h" + +extern void cmx255_init(void); +extern void cmx270_init(void); + +/* virtual addresses for statically mapped regions */ +#define CMX2XX_VIRT_BASE (0xe8000000) +#define CMX2XX_IT8152_VIRT (CMX2XX_VIRT_BASE) + +/* physical address if local-bus attached devices */ +#define CMX255_DM9000_PHYS_BASE (PXA_CS1_PHYS + (8 << 22)) +#define CMX270_DM9000_PHYS_BASE (PXA_CS1_PHYS + (6 << 22)) + +/* leds */ +#define CMX255_GPIO_RED (27) +#define CMX255_GPIO_GREEN (32) +#define CMX270_GPIO_RED (93) +#define CMX270_GPIO_GREEN (94) + +/* GPIO IRQ usage */ +#define GPIO22_ETHIRQ (22) +#define GPIO10_ETHIRQ (10) +#define CMX255_GPIO_IT8152_IRQ (0) +#define CMX270_GPIO_IT8152_IRQ (22) + +#define CMX255_ETHIRQ IRQ_GPIO(GPIO22_ETHIRQ) +#define CMX270_ETHIRQ IRQ_GPIO(GPIO10_ETHIRQ) + +#if defined(CONFIG_DM9000) || defined(CONFIG_DM9000_MODULE) +static struct resource cmx255_dm9000_resource[] = { + [0] = { + .start = CMX255_DM9000_PHYS_BASE, + .end = CMX255_DM9000_PHYS_BASE + 3, + .flags = IORESOURCE_MEM, + }, + [1] = { + .start = CMX255_DM9000_PHYS_BASE + 4, + .end = CMX255_DM9000_PHYS_BASE + 4 + 500, + .flags = IORESOURCE_MEM, + }, + [2] = { + .start = CMX255_ETHIRQ, + .end = CMX255_ETHIRQ, + .flags = IORESOURCE_IRQ | IORESOURCE_IRQ_HIGHEDGE, + } +}; + +static struct resource cmx270_dm9000_resource[] = { + [0] = { + .start = CMX270_DM9000_PHYS_BASE, + .end = CMX270_DM9000_PHYS_BASE + 3, + .flags = IORESOURCE_MEM, + }, + [1] = { + .start = CMX270_DM9000_PHYS_BASE + 8, + .end = CMX270_DM9000_PHYS_BASE + 8 + 500, + .flags = IORESOURCE_MEM, + }, + [2] = { + .start = CMX270_ETHIRQ, + .end = CMX270_ETHIRQ, + .flags = IORESOURCE_IRQ | IORESOURCE_IRQ_HIGHEDGE, + } +}; + +static struct dm9000_plat_data cmx270_dm9000_platdata = { + .flags = DM9000_PLATF_32BITONLY, +}; + +static struct platform_device cmx2xx_dm9000_device = { + .name = "dm9000", + .id = 0, + .num_resources = ARRAY_SIZE(cmx270_dm9000_resource), + .dev = { + .platform_data = &cmx270_dm9000_platdata, + } +}; + +static void __init cmx2xx_init_dm9000(void) +{ + if (cpu_is_pxa25x()) + cmx2xx_dm9000_device.resource = cmx255_dm9000_resource; + else + cmx2xx_dm9000_device.resource = cmx270_dm9000_resource; + platform_device_register(&cmx2xx_dm9000_device); +} +#else +static inline void cmx2xx_init_dm9000(void) {} +#endif + +/* UCB1400 touchscreen controller */ +#if defined(CONFIG_TOUCHSCREEN_UCB1400) || defined(CONFIG_TOUCHSCREEN_UCB1400_MODULE) +static struct platform_device cmx2xx_ts_device = { + .name = "ucb1400_ts", + .id = -1, +}; + +static void __init cmx2xx_init_touchscreen(void) +{ + platform_device_register(&cmx2xx_ts_device); +} +#else +static inline void cmx2xx_init_touchscreen(void) {} +#endif + +/* CM-X270 LEDs */ +#if defined(CONFIG_LEDS_GPIO) || defined(CONFIG_LEDS_GPIO_MODULE) +static struct gpio_led cmx2xx_leds[] = { + [0] = { + .name = "cm-x2xx:red", + .default_trigger = "nand-disk", + .active_low = 1, + }, + [1] = { + .name = "cm-x2xx:green", + .default_trigger = "heartbeat", + .active_low = 1, + }, +}; + +static struct gpio_led_platform_data cmx2xx_gpio_led_pdata = { + .num_leds = ARRAY_SIZE(cmx2xx_leds), + .leds = cmx2xx_leds, +}; + +static struct platform_device cmx2xx_led_device = { + .name = "leds-gpio", + .id = -1, + .dev = { + .platform_data = &cmx2xx_gpio_led_pdata, + }, +}; + +static void __init cmx2xx_init_leds(void) +{ + if (cpu_is_pxa25x()) { + cmx2xx_leds[0].gpio = CMX255_GPIO_RED; + cmx2xx_leds[1].gpio = CMX255_GPIO_GREEN; + } else { + cmx2xx_leds[0].gpio = CMX270_GPIO_RED; + cmx2xx_leds[1].gpio = CMX270_GPIO_GREEN; + } + platform_device_register(&cmx2xx_led_device); +} +#else +static inline void cmx2xx_init_leds(void) {} +#endif + +#if defined(CONFIG_FB_PXA) || defined(CONFIG_FB_PXA_MODULE) +/* + Display definitions + keep these for backwards compatibility, although symbolic names (as + e.g. in lpd270.c) looks better +*/ +#define MTYPE_STN320x240 0 +#define MTYPE_TFT640x480 1 +#define MTYPE_CRT640x480 2 +#define MTYPE_CRT800x600 3 +#define MTYPE_TFT320x240 6 +#define MTYPE_STN640x480 7 + +static struct pxafb_mode_info generic_stn_320x240_mode = { + .pixclock = 76923, + .bpp = 8, + .xres = 320, + .yres = 240, + .hsync_len = 3, + .vsync_len = 2, + .left_margin = 3, + .upper_margin = 0, + .right_margin = 3, + .lower_margin = 0, + .sync = (FB_SYNC_HOR_HIGH_ACT | + FB_SYNC_VERT_HIGH_ACT), + .cmap_greyscale = 0, +}; + +static struct pxafb_mach_info generic_stn_320x240 = { + .modes = &generic_stn_320x240_mode, + .num_modes = 1, + .lccr0 = 0, + .lccr3 = (LCCR3_PixClkDiv(0x03) | + LCCR3_Acb(0xff) | + LCCR3_PCP), + .cmap_inverse = 0, + .cmap_static = 0, +}; + +static struct pxafb_mode_info generic_tft_640x480_mode = { + .pixclock = 38461, + .bpp = 8, + .xres = 640, + .yres = 480, + .hsync_len = 60, + .vsync_len = 2, + .left_margin = 70, + .upper_margin = 10, + .right_margin = 70, + .lower_margin = 5, + .sync = 0, + .cmap_greyscale = 0, +}; + +static struct pxafb_mach_info generic_tft_640x480 = { + .modes = &generic_tft_640x480_mode, + .num_modes = 1, + .lccr0 = (LCCR0_PAS), + .lccr3 = (LCCR3_PixClkDiv(0x01) | + LCCR3_Acb(0xff) | + LCCR3_PCP), + .cmap_inverse = 0, + .cmap_static = 0, +}; + +static struct pxafb_mode_info generic_crt_640x480_mode = { + .pixclock = 38461, + .bpp = 8, + .xres = 640, + .yres = 480, + .hsync_len = 63, + .vsync_len = 2, + .left_margin = 81, + .upper_margin = 33, + .right_margin = 16, + .lower_margin = 10, + .sync = (FB_SYNC_HOR_HIGH_ACT | + FB_SYNC_VERT_HIGH_ACT), + .cmap_greyscale = 0, +}; + +static struct pxafb_mach_info generic_crt_640x480 = { + .modes = &generic_crt_640x480_mode, + .num_modes = 1, + .lccr0 = (LCCR0_PAS), + .lccr3 = (LCCR3_PixClkDiv(0x01) | + LCCR3_Acb(0xff)), + .cmap_inverse = 0, + .cmap_static = 0, +}; + +static struct pxafb_mode_info generic_crt_800x600_mode = { + .pixclock = 28846, + .bpp = 8, + .xres = 800, + .yres = 600, + .hsync_len = 63, + .vsync_len = 2, + .left_margin = 26, + .upper_margin = 21, + .right_margin = 26, + .lower_margin = 11, + .sync = (FB_SYNC_HOR_HIGH_ACT | + FB_SYNC_VERT_HIGH_ACT), + .cmap_greyscale = 0, +}; + +static struct pxafb_mach_info generic_crt_800x600 = { + .modes = &generic_crt_800x600_mode, + .num_modes = 1, + .lccr0 = (LCCR0_PAS), + .lccr3 = (LCCR3_PixClkDiv(0x02) | + LCCR3_Acb(0xff)), + .cmap_inverse = 0, + .cmap_static = 0, +}; + +static struct pxafb_mode_info generic_tft_320x240_mode = { + .pixclock = 134615, + .bpp = 16, + .xres = 320, + .yres = 240, + .hsync_len = 63, + .vsync_len = 7, + .left_margin = 75, + .upper_margin = 0, + .right_margin = 15, + .lower_margin = 15, + .sync = 0, + .cmap_greyscale = 0, +}; + +static struct pxafb_mach_info generic_tft_320x240 = { + .modes = &generic_tft_320x240_mode, + .num_modes = 1, + .lccr0 = (LCCR0_PAS), + .lccr3 = (LCCR3_PixClkDiv(0x06) | + LCCR3_Acb(0xff) | + LCCR3_PCP), + .cmap_inverse = 0, + .cmap_static = 0, +}; + +static struct pxafb_mode_info generic_stn_640x480_mode = { + .pixclock = 57692, + .bpp = 8, + .xres = 640, + .yres = 480, + .hsync_len = 4, + .vsync_len = 2, + .left_margin = 10, + .upper_margin = 5, + .right_margin = 10, + .lower_margin = 5, + .sync = (FB_SYNC_HOR_HIGH_ACT | + FB_SYNC_VERT_HIGH_ACT), + .cmap_greyscale = 0, +}; + +static struct pxafb_mach_info generic_stn_640x480 = { + .modes = &generic_stn_640x480_mode, + .num_modes = 1, + .lccr0 = 0, + .lccr3 = (LCCR3_PixClkDiv(0x02) | + LCCR3_Acb(0xff)), + .cmap_inverse = 0, + .cmap_static = 0, +}; + +static struct pxafb_mach_info *cmx2xx_display = &generic_crt_640x480; + +static int __init cmx2xx_set_display(char *str) +{ + int disp_type = simple_strtol(str, NULL, 0); + switch (disp_type) { + case MTYPE_STN320x240: + cmx2xx_display = &generic_stn_320x240; + break; + case MTYPE_TFT640x480: + cmx2xx_display = &generic_tft_640x480; + break; + case MTYPE_CRT640x480: + cmx2xx_display = &generic_crt_640x480; + break; + case MTYPE_CRT800x600: + cmx2xx_display = &generic_crt_800x600; + break; + case MTYPE_TFT320x240: + cmx2xx_display = &generic_tft_320x240; + break; + case MTYPE_STN640x480: + cmx2xx_display = &generic_stn_640x480; + break; + default: /* fallback to CRT 640x480 */ + cmx2xx_display = &generic_crt_640x480; + break; + } + return 1; +} + +/* + This should be done really early to get proper configuration for + frame buffer. + Indeed, pxafb parameters can be used istead, but CM-X2XX bootloader + has limitied line length for kernel command line, and also it will + break compatibitlty with proprietary releases already in field. +*/ +__setup("monitor=", cmx2xx_set_display); + +static void __init cmx2xx_init_display(void) +{ + set_pxa_fb_info(cmx2xx_display); +} +#else +static inline void cmx2xx_init_display(void) {} +#endif + +#ifdef CONFIG_PM +static unsigned long sleep_save_msc[10]; + +static int cmx2xx_suspend(struct sys_device *dev, pm_message_t state) +{ + cmx2xx_pci_suspend(); + + /* save MSC registers */ + sleep_save_msc[0] = MSC0; + sleep_save_msc[1] = MSC1; + sleep_save_msc[2] = MSC2; + + /* setup power saving mode registers */ + PCFR = 0x0; + PSLR = 0xff400000; + PMCR = 0x00000005; + PWER = 0x80000000; + PFER = 0x00000000; + PRER = 0x00000000; + PGSR0 = 0xC0018800; + PGSR1 = 0x004F0002; + PGSR2 = 0x6021C000; + PGSR3 = 0x00020000; + + return 0; +} + +static int cmx2xx_resume(struct sys_device *dev) +{ + cmx2xx_pci_resume(); + + /* restore MSC registers */ + MSC0 = sleep_save_msc[0]; + MSC1 = sleep_save_msc[1]; + MSC2 = sleep_save_msc[2]; + + return 0; +} + +static struct sysdev_class cmx2xx_pm_sysclass = { + .name = "pm", + .resume = cmx2xx_resume, + .suspend = cmx2xx_suspend, +}; + +static struct sys_device cmx2xx_pm_device = { + .cls = &cmx2xx_pm_sysclass, +}; + +static int __init cmx2xx_pm_init(void) +{ + int error; + error = sysdev_class_register(&cmx2xx_pm_sysclass); + if (error == 0) + error = sysdev_register(&cmx2xx_pm_device); + return error; +} +#else +static int __init cmx2xx_pm_init(void) { return 0; } +#endif + +#if defined(CONFIG_SND_PXA2XX_AC97) || defined(CONFIG_SND_PXA2XX_AC97_MODULE) +static void __init cmx2xx_init_ac97(void) +{ + pxa_set_ac97_info(NULL); +} +#else +static inline void cmx2xx_init_ac97(void) {} +#endif + +static void __init cmx2xx_init(void) +{ + cmx2xx_pm_init(); + + if (cpu_is_pxa25x()) + cmx255_init(); + else + cmx270_init(); + + cmx2xx_init_dm9000(); + cmx2xx_init_display(); + cmx2xx_init_ac97(); + cmx2xx_init_touchscreen(); + cmx2xx_init_leds(); +} + +static void __init cmx2xx_init_irq(void) +{ + pxa27x_init_irq(); + + if (cpu_is_pxa25x()) { + pxa25x_init_irq(); + cmx2xx_pci_init_irq(CMX255_GPIO_IT8152_IRQ); + } else { + pxa27x_init_irq(); + cmx2xx_pci_init_irq(CMX270_GPIO_IT8152_IRQ); + } +} + +#ifdef CONFIG_PCI +/* Map PCI companion statically */ +static struct map_desc cmx2xx_io_desc[] __initdata = { + [0] = { /* PCI bridge */ + .virtual = CMX2XX_IT8152_VIRT, + .pfn = __phys_to_pfn(PXA_CS4_PHYS), + .length = SZ_64M, + .type = MT_DEVICE + }, +}; + +static void __init cmx2xx_map_io(void) +{ + pxa_map_io(); + iotable_init(cmx2xx_io_desc, ARRAY_SIZE(cmx2xx_io_desc)); + + it8152_base_address = CMX2XX_IT8152_VIRT; +} +#else +static void __init cmx2xx_map_io(void) +{ + pxa_map_io(); +} +#endif + +MACHINE_START(ARMCORE, "Compulab CM-X2XX") + .boot_params = 0xa0000100, + .phys_io = 0x40000000, + .io_pg_offst = (io_p2v(0x40000000) >> 18) & 0xfffc, + .map_io = cmx2xx_map_io, + .init_irq = cmx2xx_init_irq, + .timer = &pxa_timer, + .init_machine = cmx2xx_init, +MACHINE_END diff --git a/arch/arm/mach-pxa/cm-x300.c b/arch/arm/mach-pxa/cm-x300.c new file mode 100644 index 00000000000..deb46cd144b --- /dev/null +++ b/arch/arm/mach-pxa/cm-x300.c @@ -0,0 +1,465 @@ +/* + * linux/arch/arm/mach-pxa/cm-x300.c + * + * Support for the CompuLab CM-X300 modules + * + * Copyright (C) 2008 CompuLab Ltd. + * + * Mike Rapoport <mike@compulab.co.il> + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ + +#include <linux/module.h> +#include <linux/kernel.h> +#include <linux/interrupt.h> +#include <linux/init.h> +#include <linux/platform_device.h> + +#include <linux/gpio.h> +#include <linux/dm9000.h> +#include <linux/leds.h> + +#include <linux/i2c.h> +#include <linux/i2c/pca953x.h> + +#include <asm/mach-types.h> +#include <asm/mach/arch.h> + +#include <mach/mfp-pxa300.h> + +#include <mach/hardware.h> +#include <mach/gpio.h> +#include <mach/pxafb.h> +#include <mach/mmc.h> +#include <mach/ohci.h> +#include <mach/i2c.h> +#include <mach/pxa3xx_nand.h> + +#include <asm/mach/map.h> + +#include "generic.h" + +#define CM_X300_ETH_PHYS 0x08000010 + +#define GPIO82_MMC2_IRQ (82) +#define GPIO85_MMC2_WP (85) + +#define CM_X300_MMC2_IRQ IRQ_GPIO(GPIO82_MMC2_IRQ) + +static mfp_cfg_t cm_x300_mfp_cfg[] __initdata = { + /* LCD */ + GPIO54_LCD_LDD_0, + GPIO55_LCD_LDD_1, + GPIO56_LCD_LDD_2, + GPIO57_LCD_LDD_3, + GPIO58_LCD_LDD_4, + GPIO59_LCD_LDD_5, + GPIO60_LCD_LDD_6, + GPIO61_LCD_LDD_7, + GPIO62_LCD_LDD_8, + GPIO63_LCD_LDD_9, + GPIO64_LCD_LDD_10, + GPIO65_LCD_LDD_11, + GPIO66_LCD_LDD_12, + GPIO67_LCD_LDD_13, + GPIO68_LCD_LDD_14, + GPIO69_LCD_LDD_15, + GPIO72_LCD_FCLK, + GPIO73_LCD_LCLK, + GPIO74_LCD_PCLK, + GPIO75_LCD_BIAS, + + /* BTUART */ + GPIO111_UART2_RTS, + GPIO112_UART2_RXD | MFP_LPM_EDGE_FALL, + GPIO113_UART2_TXD, + GPIO114_UART2_CTS | MFP_LPM_EDGE_BOTH, + + /* STUART */ + GPIO109_UART3_TXD, + GPIO110_UART3_RXD | MFP_LPM_EDGE_FALL, + + /* AC97 */ + GPIO23_AC97_nACRESET, + GPIO24_AC97_SYSCLK, + GPIO29_AC97_BITCLK, + GPIO25_AC97_SDATA_IN_0, + GPIO27_AC97_SDATA_OUT, + GPIO28_AC97_SYNC, + + /* Keypad */ + GPIO115_KP_MKIN_0 | MFP_LPM_EDGE_BOTH, + GPIO116_KP_MKIN_1 | MFP_LPM_EDGE_BOTH, + GPIO117_KP_MKIN_2 | MFP_LPM_EDGE_BOTH, + GPIO118_KP_MKIN_3 | MFP_LPM_EDGE_BOTH, + GPIO119_KP_MKIN_4 | MFP_LPM_EDGE_BOTH, + GPIO120_KP_MKIN_5 | MFP_LPM_EDGE_BOTH, + GPIO2_2_KP_MKIN_6 | MFP_LPM_EDGE_BOTH, + GPIO3_2_KP_MKIN_7 | MFP_LPM_EDGE_BOTH, + GPIO121_KP_MKOUT_0, + GPIO122_KP_MKOUT_1, + GPIO123_KP_MKOUT_2, + GPIO124_KP_MKOUT_3, + GPIO125_KP_MKOUT_4, + GPIO4_2_KP_MKOUT_5, + + /* MMC1 */ + GPIO3_MMC1_DAT0, + GPIO4_MMC1_DAT1 | MFP_LPM_EDGE_BOTH, + GPIO5_MMC1_DAT2, + GPIO6_MMC1_DAT3, + GPIO7_MMC1_CLK, + GPIO8_MMC1_CMD, /* CMD0 for slot 0 */ + + /* MMC2 */ + GPIO9_MMC2_DAT0, + GPIO10_MMC2_DAT1 | MFP_LPM_EDGE_BOTH, + GPIO11_MMC2_DAT2, + GPIO12_MMC2_DAT3, + GPIO13_MMC2_CLK, + GPIO14_MMC2_CMD, + + /* FFUART */ + GPIO30_UART1_RXD | MFP_LPM_EDGE_FALL, + GPIO31_UART1_TXD, + GPIO32_UART1_CTS, + GPIO37_UART1_RTS, + GPIO33_UART1_DCD, + GPIO34_UART1_DSR | MFP_LPM_EDGE_FALL, + GPIO35_UART1_RI, + GPIO36_UART1_DTR, + + /* GPIOs */ + GPIO79_GPIO, /* LED */ + GPIO82_GPIO | MFP_PULL_HIGH, /* MMC CD */ + GPIO85_GPIO, /* MMC WP */ + GPIO99_GPIO, /* Ethernet IRQ */ +}; + +#if defined(CONFIG_DM9000) || defined(CONFIG_DM9000_MODULE) +static struct resource dm9000_resources[] = { + [0] = { + .start = CM_X300_ETH_PHYS, + .end = CM_X300_ETH_PHYS + 0x3, + .flags = IORESOURCE_MEM, + }, + [1] = { + .start = CM_X300_ETH_PHYS + 0x4, + .end = CM_X300_ETH_PHYS + 0x4 + 500, + .flags = IORESOURCE_MEM, + }, + [2] = { + .start = IRQ_GPIO(mfp_to_gpio(MFP_PIN_GPIO99)), + .end = IRQ_GPIO(mfp_to_gpio(MFP_PIN_GPIO99)), + .flags = IORESOURCE_IRQ | IORESOURCE_IRQ_HIGHEDGE, + } +}; + +static struct dm9000_plat_data cm_x300_dm9000_platdata = { + .flags = DM9000_PLATF_16BITONLY, +}; + +static struct platform_device dm9000_device = { + .name = "dm9000", + .id = 0, + .num_resources = ARRAY_SIZE(dm9000_resources), + .resource = dm9000_resources, + .dev = { + .platform_data = &cm_x300_dm9000_platdata, + } + +}; + +static void __init cm_x300_init_dm9000(void) +{ + platform_device_register(&dm9000_device); +} +#else +static inline void cm_x300_init_dm9000(void) {} +#endif + +#if defined(CONFIG_FB_PXA) || defined(CONFIG_FB_PXA_MODULE) +static struct pxafb_mode_info cm_x300_lcd_modes[] = { + [0] = { + .pixclock = 38000, + .bpp = 16, + .xres = 480, + .yres = 640, + .hsync_len = 8, + .vsync_len = 2, + .left_margin = 8, + .upper_margin = 0, + .right_margin = 24, + .lower_margin = 4, + .cmap_greyscale = 0, + }, + [1] = { + .pixclock = 153800, + .bpp = 16, + .xres = 240, + .yres = 320, + .hsync_len = 8, + .vsync_len = 2, + .left_margin = 8, + .upper_margin = 2, + .right_margin = 88, + .lower_margin = 2, + .cmap_greyscale = 0, + }, +}; + +static struct pxafb_mach_info cm_x300_lcd = { + .modes = cm_x300_lcd_modes, + .num_modes = 2, + .lcd_conn = LCD_COLOR_TFT_16BPP | LCD_PCLK_EDGE_FALL, +}; + +static void __init cm_x300_init_lcd(void) +{ + set_pxa_fb_info(&cm_x300_lcd); +} +#else +static inline void cm_x300_init_lcd(void) {} +#endif + +#if defined(CONFIG_MTD_NAND_PXA3xx) || defined(CONFIG_MTD_NAND_PXA3xx_MODULE) +static struct mtd_partition cm_x300_nand_partitions[] = { + [0] = { + .name = "OBM", + .offset = 0, + .size = SZ_256K, + .mask_flags = MTD_WRITEABLE, /* force read-only */ + }, + [1] = { + .name = "U-Boot", + .offset = MTDPART_OFS_APPEND, + .size = SZ_256K, + .mask_flags = MTD_WRITEABLE, /* force read-only */ + }, + [2] = { + .name = "Environment", + .offset = MTDPART_OFS_APPEND, + .size = SZ_256K, + }, + [3] = { + .name = "reserved", + .offset = MTDPART_OFS_APPEND, + .size = SZ_256K + SZ_1M, + .mask_flags = MTD_WRITEABLE, /* force read-only */ + }, + [4] = { + .name = "kernel", + .offset = MTDPART_OFS_APPEND, + .size = SZ_4M, + }, + [5] = { + .name = "fs", + .offset = MTDPART_OFS_APPEND, + .size = MTDPART_SIZ_FULL, + }, +}; + +static struct pxa3xx_nand_platform_data cm_x300_nand_info = { + .enable_arbiter = 1, + .parts = cm_x300_nand_partitions, + .nr_parts = ARRAY_SIZE(cm_x300_nand_partitions), +}; + +static void __init cm_x300_init_nand(void) +{ + pxa3xx_set_nand_info(&cm_x300_nand_info); +} +#else +static inline void cm_x300_init_nand(void) {} +#endif + +#if defined(CONFIG_MMC) || defined(CONFIG_MMC_MODULE) +/* The first MMC slot of CM-X300 is hardwired to Libertas card and has + no detection/ro pins */ +static int cm_x300_mci_init(struct device *dev, + irq_handler_t cm_x300_detect_int, + void *data) +{ + return 0; +} + +static void cm_x300_mci_exit(struct device *dev, void *data) +{ +} + +static struct pxamci_platform_data cm_x300_mci_platform_data = { + .detect_delay = 20, + .ocr_mask = MMC_VDD_32_33|MMC_VDD_33_34, + .init = cm_x300_mci_init, + .exit = cm_x300_mci_exit, +}; + +static int cm_x300_mci2_ro(struct device *dev) +{ + return gpio_get_value(GPIO85_MMC2_WP); +} + +static int cm_x300_mci2_init(struct device *dev, + irq_handler_t cm_x300_detect_int, + void *data) +{ + int err; + + /* + * setup GPIO for CM-X300 MMC controller + */ + err = gpio_request(GPIO82_MMC2_IRQ, "mmc card detect"); + if (err) + goto err_request_cd; + gpio_direction_input(GPIO82_MMC2_IRQ); + + err = gpio_request(GPIO85_MMC2_WP, "mmc write protect"); + if (err) + goto err_request_wp; + gpio_direction_input(GPIO85_MMC2_WP); + + err = request_irq(CM_X300_MMC2_IRQ, cm_x300_detect_int, + IRQF_TRIGGER_RISING | IRQF_TRIGGER_FALLING, + "MMC card detect", data); + if (err) { + printk(KERN_ERR "%s: MMC/SD/SDIO: " + "can't request card detect IRQ\n", __func__); + goto err_request_irq; + } + + return 0; + +err_request_irq: + gpio_free(GPIO85_MMC2_WP); +err_request_wp: + gpio_free(GPIO82_MMC2_IRQ); +err_request_cd: + return err; +} + +static void cm_x300_mci2_exit(struct device *dev, void *data) +{ + free_irq(CM_X300_MMC2_IRQ, data); + gpio_free(GPIO82_MMC2_IRQ); + gpio_free(GPIO85_MMC2_WP); +} + +static struct pxamci_platform_data cm_x300_mci2_platform_data = { + .detect_delay = 20, + .ocr_mask = MMC_VDD_32_33|MMC_VDD_33_34, + .init = cm_x300_mci2_init, + .exit = cm_x300_mci2_exit, + .get_ro = cm_x300_mci2_ro, +}; + +static void __init cm_x300_init_mmc(void) +{ + pxa_set_mci_info(&cm_x300_mci_platform_data); + pxa3xx_set_mci2_info(&cm_x300_mci2_platform_data); +} +#else +static inline void cm_x300_init_mmc(void) {} +#endif + +#if defined(CONFIG_USB_OHCI_HCD) || defined(CONFIG_USB_OHCI_HCD_MODULE) +static struct pxaohci_platform_data cm_x300_ohci_platform_data = { + .port_mode = PMM_PERPORT_MODE, + .flags = ENABLE_PORT1 | ENABLE_PORT2 | POWER_CONTROL_LOW, +}; + +static void __init cm_x300_init_ohci(void) +{ + pxa_set_ohci_info(&cm_x300_ohci_platform_data); +} +#else +static inline void cm_x300_init_ohci(void) {} +#endif + +#if defined(CONFIG_LEDS_GPIO) || defined(CONFIG_LEDS_GPIO_MODULE) +static struct gpio_led cm_x300_leds[] = { + [0] = { + .name = "cm-x300:green", + .default_trigger = "heartbeat", + .gpio = 79, + .active_low = 1, + }, +}; + +static struct gpio_led_platform_data cm_x300_gpio_led_pdata = { + .num_leds = ARRAY_SIZE(cm_x300_leds), + .leds = cm_x300_leds, +}; + +static struct platform_device cm_x300_led_device = { + .name = "leds-gpio", + .id = -1, + .dev = { + .platform_data = &cm_x300_gpio_led_pdata, + }, +}; + +static void __init cm_x300_init_leds(void) +{ + platform_device_register(&cm_x300_led_device); +} +#else +static inline void cm_x300_init_leds(void) {} +#endif + +#if defined(CONFIG_I2C) || defined(CONFIG_I2C_MODULE) +/* PCA9555 */ +static struct pca953x_platform_data cm_x300_gpio_ext_pdata_0 = { + .gpio_base = 128, +}; + +static struct pca953x_platform_data cm_x300_gpio_ext_pdata_1 = { + .gpio_base = 144, +}; + +static struct i2c_board_info cm_x300_gpio_ext_info[] = { + [0] = { + I2C_BOARD_INFO("pca9555", 0x24), + .platform_data = &cm_x300_gpio_ext_pdata_0, + }, + [1] = { + I2C_BOARD_INFO("pca9555", 0x25), + .platform_data = &cm_x300_gpio_ext_pdata_1, + }, +}; + +static void __init cm_x300_init_i2c(void) +{ + pxa_set_i2c_info(NULL); + i2c_register_board_info(0, cm_x300_gpio_ext_info, + ARRAY_SIZE(cm_x300_gpio_ext_info)); +} +#else +static inline void cm_x300_init_i2c(void) {} +#endif + +static void __init cm_x300_init(void) +{ + /* board-processor specific GPIO initialization */ + pxa3xx_mfp_config(ARRAY_AND_SIZE(cm_x300_mfp_cfg)); + + cm_x300_init_dm9000(); + cm_x300_init_lcd(); + cm_x300_init_ohci(); + cm_x300_init_mmc(); + cm_x300_init_nand(); + cm_x300_init_leds(); + cm_x300_init_i2c(); +} + +MACHINE_START(CM_X300, "CM-X300 module") + .phys_io = 0x40000000, + .boot_params = 0xa0000100, + .io_pg_offst = (io_p2v(0x40000000) >> 18) & 0xfffc, + .map_io = pxa_map_io, + .init_irq = pxa3xx_init_irq, + .timer = &pxa_timer, + .init_machine = cm_x300_init, +MACHINE_END diff --git a/arch/arm/mach-pxa/colibri.c b/arch/arm/mach-pxa/colibri.c index 574839d7c13..e8473624427 100644 --- a/arch/arm/mach-pxa/colibri.c +++ b/arch/arm/mach-pxa/colibri.c @@ -21,20 +21,25 @@ #include <linux/mtd/partitions.h> #include <linux/mtd/physmap.h> #include <asm/mach-types.h> -#include <asm/hardware.h> +#include <mach/hardware.h> #include <asm/irq.h> #include <asm/sizes.h> #include <asm/mach/arch.h> #include <asm/mach/map.h> #include <asm/mach/irq.h> #include <asm/mach/flash.h> -#include <asm/arch/pxa-regs.h> -#include <asm/arch/pxa2xx-gpio.h> -#include <asm/arch/colibri.h> +#include <mach/pxa-regs.h> +#include <mach/mfp-pxa27x.h> +#include <mach/colibri.h> #include "generic.h" #include "devices.h" +static unsigned long colibri_pin_config[] __initdata = { + GPIO78_nCS_2, /* Ethernet CS */ + GPIO114_GPIO, /* Ethernet IRQ */ +}; + /* * Flash */ @@ -116,9 +121,7 @@ static struct platform_device *colibri_devices[] __initdata = { static void __init colibri_init(void) { - /* DM9000 LAN */ - pxa_gpio_mode(GPIO78_nCS_2_MD); - pxa_gpio_mode(GPIO_DM9000 | GPIO_IN); + pxa2xx_mfp_config(ARRAY_AND_SIZE(colibri_pin_config)); platform_add_devices(colibri_devices, ARRAY_SIZE(colibri_devices)); } diff --git a/arch/arm/mach-pxa/corgi.c b/arch/arm/mach-pxa/corgi.c index b757dd75665..65558d6aa22 100644 --- a/arch/arm/mach-pxa/corgi.c +++ b/arch/arm/mach-pxa/corgi.c @@ -20,28 +20,35 @@ #include <linux/interrupt.h> #include <linux/mmc/host.h> #include <linux/pm.h> +#include <linux/gpio.h> #include <linux/backlight.h> +#include <linux/io.h> +#include <linux/spi/spi.h> +#include <linux/spi/ads7846.h> +#include <linux/spi/corgi_lcd.h> #include <video/w100fb.h> #include <asm/setup.h> #include <asm/memory.h> #include <asm/mach-types.h> -#include <asm/hardware.h> +#include <mach/hardware.h> #include <asm/irq.h> -#include <asm/io.h> #include <asm/system.h> #include <asm/mach/arch.h> #include <asm/mach/map.h> #include <asm/mach/irq.h> -#include <asm/arch/pxa-regs.h> -#include <asm/arch/pxa2xx-gpio.h> -#include <asm/arch/irda.h> -#include <asm/arch/mmc.h> -#include <asm/arch/udc.h> -#include <asm/arch/corgi.h> -#include <asm/arch/sharpsl.h> +#include <mach/pxa-regs.h> +#include <mach/pxa2xx-regs.h> +#include <mach/mfp-pxa25x.h> +#include <mach/i2c.h> +#include <mach/irda.h> +#include <mach/mmc.h> +#include <mach/udc.h> +#include <mach/pxa2xx_spi.h> +#include <mach/corgi.h> +#include <mach/sharpsl.h> #include <asm/mach/sharpsl_param.h> #include <asm/hardware/scoop.h> @@ -50,6 +57,61 @@ #include "devices.h" #include "sharpsl.h" +static unsigned long corgi_pin_config[] __initdata = { + /* Static Memory I/O */ + GPIO78_nCS_2, /* w100fb */ + GPIO80_nCS_4, /* scoop */ + + /* SSP1 */ + GPIO23_SSP1_SCLK, + GPIO25_SSP1_TXD, + GPIO26_SSP1_RXD, + GPIO24_GPIO, /* CORGI_GPIO_ADS7846_CS - SFRM as chip select */ + + /* I2S */ + GPIO28_I2S_BITCLK_OUT, + GPIO29_I2S_SDATA_IN, + GPIO30_I2S_SDATA_OUT, + GPIO31_I2S_SYNC, + GPIO32_I2S_SYSCLK, + + /* Infra-Red */ + GPIO47_FICP_TXD, + GPIO46_FICP_RXD, + + /* FFUART */ + GPIO40_FFUART_DTR, + GPIO41_FFUART_RTS, + GPIO39_FFUART_TXD, + GPIO37_FFUART_DSR, + GPIO34_FFUART_RXD, + GPIO35_FFUART_CTS, + + /* PC Card */ + GPIO48_nPOE, + GPIO49_nPWE, + GPIO50_nPIOR, + GPIO51_nPIOW, + GPIO52_nPCE_1, + GPIO53_nPCE_2, + GPIO54_nPSKTSEL, + GPIO55_nPREG, + GPIO56_nPWAIT, + GPIO57_nIOIS16, + + /* MMC */ + GPIO6_MMC_CLK, + GPIO8_MMC_CS0, + + /* GPIO */ + GPIO9_GPIO, /* CORGI_GPIO_nSD_DETECT */ + GPIO7_GPIO, /* CORGI_GPIO_nSD_WP */ + GPIO33_GPIO, /* CORGI_GPIO_SD_PWR */ + GPIO22_GPIO, /* CORGI_GPIO_IR_ON */ + GPIO44_GPIO, /* CORGI_GPIO_HSYNC */ + + GPIO1_GPIO | WAKEUP_ON_EDGE_RISE, +}; /* * Corgi SCOOP Device @@ -65,6 +127,7 @@ static struct resource corgi_scoop_resources[] = { static struct scoop_config corgi_scoop_setup = { .io_dir = CORGI_SCOOP_IO_DIR, .io_out = CORGI_SCOOP_IO_OUT, + .gpio_base = CORGI_SCOOP_GPIO_BASE, }; struct platform_device corgiscoop_device = { @@ -77,27 +140,6 @@ struct platform_device corgiscoop_device = { .resource = corgi_scoop_resources, }; -static void corgi_pcmcia_init(void) -{ - /* Setup default state of GPIO outputs - before we enable them as outputs. */ - GPSR(GPIO48_nPOE) = GPIO_bit(GPIO48_nPOE) | - GPIO_bit(GPIO49_nPWE) | GPIO_bit(GPIO50_nPIOR) | - GPIO_bit(GPIO51_nPIOW) | GPIO_bit(GPIO52_nPCE_1) | - GPIO_bit(GPIO53_nPCE_2); - - pxa_gpio_mode(GPIO48_nPOE_MD); - pxa_gpio_mode(GPIO49_nPWE_MD); - pxa_gpio_mode(GPIO50_nPIOR_MD); - pxa_gpio_mode(GPIO51_nPIOW_MD); - pxa_gpio_mode(GPIO55_nPREG_MD); - pxa_gpio_mode(GPIO56_nPWAIT_MD); - pxa_gpio_mode(GPIO57_nIOIS16_MD); - pxa_gpio_mode(GPIO52_nPCE_1_MD); - pxa_gpio_mode(GPIO53_nPCE_2_MD); - pxa_gpio_mode(GPIO54_pSKTSEL_MD); -} - static struct scoop_pcmcia_dev corgi_pcmcia_scoop[] = { { .dev = &corgiscoop_device.dev, @@ -110,58 +152,10 @@ static struct scoop_pcmcia_dev corgi_pcmcia_scoop[] = { static struct scoop_pcmcia_config corgi_pcmcia_config = { .devs = &corgi_pcmcia_scoop[0], .num_devs = 1, - .pcmcia_init = corgi_pcmcia_init, }; EXPORT_SYMBOL(corgiscoop_device); - -/* - * Corgi SSP Device - * - * Set the parent as the scoop device because a lot of SSP devices - * also use scoop functions and this makes the power up/down order - * work correctly. - */ -struct platform_device corgissp_device = { - .name = "corgi-ssp", - .dev = { - .parent = &corgiscoop_device.dev, - }, - .id = -1, -}; - -struct corgissp_machinfo corgi_ssp_machinfo = { - .port = 1, - .cs_lcdcon = CORGI_GPIO_LCDCON_CS, - .cs_ads7846 = CORGI_GPIO_ADS7846_CS, - .cs_max1111 = CORGI_GPIO_MAX1111_CS, - .clk_lcdcon = 76, - .clk_ads7846 = 2, - .clk_max1111 = 8, -}; - - -/* - * LCD/Framebuffer - */ -static void w100_lcdtg_suspend(struct w100fb_par *par) -{ - corgi_lcdtg_suspend(); -} - -static void w100_lcdtg_init(struct w100fb_par *par) -{ - corgi_lcdtg_hw_init(par->xres); -} - - -static struct w100_tg_info corgi_lcdtg_info = { - .change = w100_lcdtg_init, - .suspend = w100_lcdtg_suspend, - .resume = w100_lcdtg_init, -}; - static struct w100_mem_info corgi_fb_mem = { .ext_cntl = 0x00040003, .sdram_mode_reg = 0x00650021, @@ -240,7 +234,6 @@ static struct w100_mode corgi_fb_modes[] = { }; static struct w100fb_mach_info corgi_fb_info = { - .tg = &corgi_lcdtg_info, .init_mode = INIT_MODE_ROTATED, .mem = &corgi_fb_mem, .regs = &corgi_fb_regs, @@ -266,60 +259,10 @@ static struct platform_device corgifb_device = { .resource = corgi_fb_resources, .dev = { .platform_data = &corgi_fb_info, - .parent = &corgissp_device.dev, }, }; - -/* - * Corgi Backlight Device - */ -static void corgi_bl_kick_battery(void) -{ - void (*kick_batt)(void); - - kick_batt = symbol_get(sharpsl_battery_kick); - if (kick_batt) { - kick_batt(); - symbol_put(sharpsl_battery_kick); - } -} - -static void corgi_bl_set_intensity(int intensity) -{ - if (intensity > 0x10) - intensity += 0x10; - - /* Bits 0-4 are accessed via the SSP interface */ - corgi_ssp_blduty_set(intensity & 0x1f); - - /* Bit 5 is via SCOOP */ - if (intensity & 0x0020) - set_scoop_gpio(&corgiscoop_device.dev, CORGI_SCP_BACKLIGHT_CONT); - else - reset_scoop_gpio(&corgiscoop_device.dev, CORGI_SCP_BACKLIGHT_CONT); -} - -static struct generic_bl_info corgi_bl_machinfo = { - .name = "corgi-bl", - .max_intensity = 0x2f, - .default_intensity = 0x1f, - .limit_mask = 0x0b, - .set_bl_intensity = corgi_bl_set_intensity, - .kick_battery = corgi_bl_kick_battery, -}; - -static struct platform_device corgibl_device = { - .name = "generic-bl", - .dev = { - .parent = &corgifb_device.dev, - .platform_data = &corgi_bl_machinfo, - }, - .id = -1, -}; - - /* * Corgi Keyboard Device */ @@ -328,75 +271,35 @@ static struct platform_device corgikbd_device = { .id = -1, }; - /* * Corgi LEDs */ -static struct platform_device corgiled_device = { - .name = "corgi-led", - .id = -1, -}; - - -/* - * Corgi Touch Screen Device - */ -static unsigned long (*get_hsync_invperiod)(struct device *dev); - -static void inline sharpsl_wait_sync(int gpio) -{ - while((GPLR(gpio) & GPIO_bit(gpio)) == 0); - while((GPLR(gpio) & GPIO_bit(gpio)) != 0); -} - -static unsigned long corgi_get_hsync_invperiod(void) -{ - if (!get_hsync_invperiod) - get_hsync_invperiod = symbol_get(w100fb_get_hsynclen); - if (!get_hsync_invperiod) - return 0; - - return get_hsync_invperiod(&corgifb_device.dev); -} - -static void corgi_put_hsync(void) -{ - if (get_hsync_invperiod) - symbol_put(w100fb_get_hsynclen); - get_hsync_invperiod = NULL; -} - -static void corgi_wait_hsync(void) -{ - sharpsl_wait_sync(CORGI_GPIO_HSYNC); -} - -static struct resource corgits_resources[] = { - [0] = { - .start = CORGI_IRQ_GPIO_TP_INT, - .end = CORGI_IRQ_GPIO_TP_INT, - .flags = IORESOURCE_IRQ, +static struct gpio_led corgi_gpio_leds[] = { + { + .name = "corgi:amber:charge", + .default_trigger = "sharpsl-charge", + .gpio = CORGI_GPIO_LED_ORANGE, + }, + { + .name = "corgi:green:mail", + .default_trigger = "nand-disk", + .gpio = CORGI_GPIO_LED_GREEN, }, }; -static struct corgits_machinfo corgi_ts_machinfo = { - .get_hsync_invperiod = corgi_get_hsync_invperiod, - .put_hsync = corgi_put_hsync, - .wait_hsync = corgi_wait_hsync, +static struct gpio_led_platform_data corgi_gpio_leds_info = { + .leds = corgi_gpio_leds, + .num_leds = ARRAY_SIZE(corgi_gpio_leds), }; -static struct platform_device corgits_device = { - .name = "corgi-ts", +static struct platform_device corgiled_device = { + .name = "leds-gpio", + .id = -1, .dev = { - .parent = &corgissp_device.dev, - .platform_data = &corgi_ts_machinfo, + .platform_data = &corgi_gpio_leds_info, }, - .id = -1, - .num_resources = ARRAY_SIZE(corgits_resources), - .resource = corgits_resources, }; - /* * MMC/SD Device * @@ -409,20 +312,42 @@ static int corgi_mci_init(struct device *dev, irq_handler_t corgi_detect_int, vo { int err; - /* setup GPIO for PXA25x MMC controller */ - pxa_gpio_mode(GPIO6_MMCCLK_MD); - pxa_gpio_mode(GPIO8_MMCCS0_MD); - pxa_gpio_mode(CORGI_GPIO_nSD_DETECT | GPIO_IN); - pxa_gpio_mode(CORGI_GPIO_SD_PWR | GPIO_OUT); + err = gpio_request(CORGI_GPIO_nSD_DETECT, "nSD_DETECT"); + if (err) + goto err_out; - corgi_mci_platform_data.detect_delay = msecs_to_jiffies(250); + err = gpio_request(CORGI_GPIO_nSD_WP, "nSD_WP"); + if (err) + goto err_free_1; - err = request_irq(CORGI_IRQ_GPIO_nSD_DETECT, corgi_detect_int, - IRQF_DISABLED | IRQF_TRIGGER_RISING | IRQF_TRIGGER_FALLING, - "MMC card detect", data); + err = gpio_request(CORGI_GPIO_SD_PWR, "SD_PWR"); if (err) - printk(KERN_ERR "corgi_mci_init: MMC/SD: can't request MMC card detect IRQ\n"); + goto err_free_2; + gpio_direction_input(CORGI_GPIO_nSD_DETECT); + gpio_direction_input(CORGI_GPIO_nSD_WP); + gpio_direction_output(CORGI_GPIO_SD_PWR, 0); + + corgi_mci_platform_data.detect_delay = msecs_to_jiffies(250); + + err = request_irq(CORGI_IRQ_GPIO_nSD_DETECT, corgi_detect_int, + IRQF_DISABLED | IRQF_TRIGGER_RISING | + IRQF_TRIGGER_FALLING, + "MMC card detect", data); + if (err) { + pr_err("%s: MMC/SD: can't request MMC card detect IRQ\n", + __func__); + goto err_free_3; + } + return 0; + +err_free_3: + gpio_free(CORGI_GPIO_SD_PWR); +err_free_2: + gpio_free(CORGI_GPIO_nSD_WP); +err_free_1: + gpio_free(CORGI_GPIO_nSD_DETECT); +err_out: return err; } @@ -430,20 +355,20 @@ static void corgi_mci_setpower(struct device *dev, unsigned int vdd) { struct pxamci_platform_data* p_d = dev->platform_data; - if (( 1 << vdd) & p_d->ocr_mask) - GPSR1 = GPIO_bit(CORGI_GPIO_SD_PWR); - else - GPCR1 = GPIO_bit(CORGI_GPIO_SD_PWR); + gpio_set_value(CORGI_GPIO_SD_PWR, ((1 << vdd) & p_d->ocr_mask)); } static int corgi_mci_get_ro(struct device *dev) { - return GPLR(CORGI_GPIO_nSD_WP) & GPIO_bit(CORGI_GPIO_nSD_WP); + return gpio_get_value(CORGI_GPIO_nSD_WP); } static void corgi_mci_exit(struct device *dev, void *data) { free_irq(CORGI_IRQ_GPIO_nSD_DETECT, data); + gpio_free(CORGI_GPIO_SD_PWR); + gpio_free(CORGI_GPIO_nSD_WP); + gpio_free(CORGI_GPIO_nSD_DETECT); } static struct pxamci_platform_data corgi_mci_platform_data = { @@ -460,15 +385,32 @@ static struct pxamci_platform_data corgi_mci_platform_data = { */ static void corgi_irda_transceiver_mode(struct device *dev, int mode) { - if (mode & IR_OFF) - GPSR(CORGI_GPIO_IR_ON) = GPIO_bit(CORGI_GPIO_IR_ON); - else - GPCR(CORGI_GPIO_IR_ON) = GPIO_bit(CORGI_GPIO_IR_ON); + gpio_set_value(CORGI_GPIO_IR_ON, mode & IR_OFF); + pxa2xx_transceiver_mode(dev, mode); +} + +static int corgi_irda_startup(struct device *dev) +{ + int err; + + err = gpio_request(CORGI_GPIO_IR_ON, "IR_ON"); + if (err) + return err; + + gpio_direction_output(CORGI_GPIO_IR_ON, 1); + return 0; +} + +static void corgi_irda_shutdown(struct device *dev) +{ + gpio_free(CORGI_GPIO_IR_ON); } static struct pxaficp_platform_data corgi_ficp_platform_data = { - .transceiver_cap = IR_SIRMODE | IR_OFF, - .transceiver_mode = corgi_irda_transceiver_mode, + .transceiver_cap = IR_SIRMODE | IR_OFF, + .transceiver_mode = corgi_irda_transceiver_mode, + .startup = corgi_irda_startup, + .shutdown = corgi_irda_shutdown, }; @@ -480,14 +422,129 @@ static struct pxa2xx_udc_mach_info udc_info __initdata = { .gpio_pullup = CORGI_GPIO_USB_PULLUP, }; +#if defined(CONFIG_SPI_PXA2XX) || defined(CONFIG_SPI_PXA2XX_MASTER) +static struct pxa2xx_spi_master corgi_spi_info = { + .num_chipselect = 3, +}; + +static struct ads7846_platform_data corgi_ads7846_info = { + .model = 7846, + .vref_delay_usecs = 100, + .x_plate_ohms = 419, + .y_plate_ohms = 486, + .gpio_pendown = CORGI_GPIO_TP_INT, +}; + +static void corgi_ads7846_cs(u32 command) +{ + gpio_set_value(CORGI_GPIO_ADS7846_CS, !(command == PXA2XX_CS_ASSERT)); +} + +static struct pxa2xx_spi_chip corgi_ads7846_chip = { + .cs_control = corgi_ads7846_cs, +}; + +static void corgi_bl_kick_battery(void) +{ + void (*kick_batt)(void); + + kick_batt = symbol_get(sharpsl_battery_kick); + if (kick_batt) { + kick_batt(); + symbol_put(sharpsl_battery_kick); + } +} + +static struct corgi_lcd_platform_data corgi_lcdcon_info = { + .init_mode = CORGI_LCD_MODE_VGA, + .max_intensity = 0x2f, + .default_intensity = 0x1f, + .limit_mask = 0x0b, + .gpio_backlight_cont = CORGI_GPIO_BACKLIGHT_CONT, + .gpio_backlight_on = -1, + .kick_battery = corgi_bl_kick_battery, +}; + +static void corgi_lcdcon_cs(u32 command) +{ + gpio_set_value(CORGI_GPIO_LCDCON_CS, !(command == PXA2XX_CS_ASSERT)); +} + +static struct pxa2xx_spi_chip corgi_lcdcon_chip = { + .cs_control = corgi_lcdcon_cs, +}; + +static void corgi_max1111_cs(u32 command) +{ + gpio_set_value(CORGI_GPIO_MAX1111_CS, !(command == PXA2XX_CS_ASSERT)); +} + +static struct pxa2xx_spi_chip corgi_max1111_chip = { + .cs_control = corgi_max1111_cs, +}; + +static struct spi_board_info corgi_spi_devices[] = { + { + .modalias = "ads7846", + .max_speed_hz = 1200000, + .bus_num = 1, + .chip_select = 0, + .platform_data = &corgi_ads7846_info, + .controller_data= &corgi_ads7846_chip, + .irq = gpio_to_irq(CORGI_GPIO_TP_INT), + }, { + .modalias = "corgi-lcd", + .max_speed_hz = 50000, + .bus_num = 1, + .chip_select = 1, + .platform_data = &corgi_lcdcon_info, + .controller_data= &corgi_lcdcon_chip, + }, { + .modalias = "max1111", + .max_speed_hz = 450000, + .bus_num = 1, + .chip_select = 2, + .controller_data= &corgi_max1111_chip, + }, +}; + +static void __init corgi_init_spi(void) +{ + int err; + + err = gpio_request(CORGI_GPIO_ADS7846_CS, "ADS7846_CS"); + if (err) + return; + + err = gpio_request(CORGI_GPIO_LCDCON_CS, "LCDCON_CS"); + if (err) + goto err_free_1; + + err = gpio_request(CORGI_GPIO_MAX1111_CS, "MAX1111_CS"); + if (err) + goto err_free_2; + + gpio_direction_output(CORGI_GPIO_ADS7846_CS, 1); + gpio_direction_output(CORGI_GPIO_LCDCON_CS, 1); + gpio_direction_output(CORGI_GPIO_MAX1111_CS, 1); + + pxa2xx_set_spi_info(1, &corgi_spi_info); + spi_register_board_info(ARRAY_AND_SIZE(corgi_spi_devices)); + return; + +err_free_2: + gpio_free(CORGI_GPIO_LCDCON_CS); +err_free_1: + gpio_free(CORGI_GPIO_ADS7846_CS); +} +#else +static inline void corgi_init_spi(void) {} +#endif static struct platform_device *devices[] __initdata = { &corgiscoop_device, - &corgissp_device, &corgifb_device, &corgikbd_device, - &corgibl_device, - &corgits_device, &corgiled_device, }; @@ -495,7 +552,8 @@ static void corgi_poweroff(void) { if (!machine_is_corgi()) /* Green LED off tells the bootloader to halt */ - reset_scoop_gpio(&corgiscoop_device.dev, CORGI_SCP_LED_GREEN); + gpio_set_value(CORGI_GPIO_LED_GREEN, 0); + arm_machine_restart('h'); } @@ -503,7 +561,8 @@ static void corgi_restart(char mode) { if (!machine_is_corgi()) /* Green LED on tells the bootloader to reboot */ - set_scoop_gpio(&corgiscoop_device.dev, CORGI_SCP_LED_GREEN); + gpio_set_value(CORGI_GPIO_LED_GREEN, 1); + arm_machine_restart('h'); } @@ -512,24 +571,17 @@ static void __init corgi_init(void) pm_power_off = corgi_poweroff; arm_pm_restart = corgi_restart; - /* setup sleep mode values */ - PWER = 0x00000002; - PFER = 0x00000000; - PRER = 0x00000002; - PGSR0 = 0x0158C000; - PGSR1 = 0x00FF0080; - PGSR2 = 0x0001C004; /* Stop 3.6MHz and drive HIGH to PCMCIA and CS */ PCFR |= PCFR_OPDE; - corgi_ssp_set_machinfo(&corgi_ssp_machinfo); + pxa2xx_mfp_config(ARRAY_AND_SIZE(corgi_pin_config)); - pxa_gpio_mode(CORGI_GPIO_IR_ON | GPIO_OUT); - pxa_gpio_mode(CORGI_GPIO_HSYNC | GPIO_IN); + corgi_init_spi(); pxa_set_udc_info(&udc_info); pxa_set_mci_info(&corgi_mci_platform_data); pxa_set_ficp_info(&corgi_ficp_platform_data); + pxa_set_i2c_info(NULL); platform_scoop_config = &corgi_pcmcia_config; diff --git a/arch/arm/mach-pxa/corgi_lcd.c b/arch/arm/mach-pxa/corgi_lcd.c deleted file mode 100644 index 9328df37afd..00000000000 --- a/arch/arm/mach-pxa/corgi_lcd.c +++ /dev/null @@ -1,290 +0,0 @@ -/* - * linux/arch/arm/mach-pxa/corgi_lcd.c - * - * Corgi/Spitz LCD Specific Code - * - * Copyright (C) 2005 Richard Purdie - * - * Connectivity: - * Corgi - LCD to ATI Imageon w100 (Wallaby) - * Spitz - LCD to PXA Framebuffer - * - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License version 2 as - * published by the Free Software Foundation. - * - */ - -#include <linux/delay.h> -#include <linux/kernel.h> -#include <linux/platform_device.h> -#include <linux/module.h> -#include <linux/string.h> -#include <asm/arch/akita.h> -#include <asm/arch/corgi.h> -#include <asm/hardware.h> -#include <asm/arch/pxa-regs.h> -#include <asm/arch/sharpsl.h> -#include <asm/arch/spitz.h> -#include <asm/hardware/scoop.h> -#include <asm/mach/sharpsl_param.h> -#include "generic.h" - -/* Register Addresses */ -#define RESCTL_ADRS 0x00 -#define PHACTRL_ADRS 0x01 -#define DUTYCTRL_ADRS 0x02 -#define POWERREG0_ADRS 0x03 -#define POWERREG1_ADRS 0x04 -#define GPOR3_ADRS 0x05 -#define PICTRL_ADRS 0x06 -#define POLCTRL_ADRS 0x07 - -/* Register Bit Definitions */ -#define RESCTL_QVGA 0x01 -#define RESCTL_VGA 0x00 - -#define POWER1_VW_ON 0x01 /* VW Supply FET ON */ -#define POWER1_GVSS_ON 0x02 /* GVSS(-8V) Power Supply ON */ -#define POWER1_VDD_ON 0x04 /* VDD(8V),SVSS(-4V) Power Supply ON */ - -#define POWER1_VW_OFF 0x00 /* VW Supply FET OFF */ -#define POWER1_GVSS_OFF 0x00 /* GVSS(-8V) Power Supply OFF */ -#define POWER1_VDD_OFF 0x00 /* VDD(8V),SVSS(-4V) Power Supply OFF */ - -#define POWER0_COM_DCLK 0x01 /* COM Voltage DC Bias DAC Serial Data Clock */ -#define POWER0_COM_DOUT 0x02 /* COM Voltage DC Bias DAC Serial Data Out */ -#define POWER0_DAC_ON 0x04 /* DAC Power Supply ON */ -#define POWER0_COM_ON 0x08 /* COM Power Supply ON */ -#define POWER0_VCC5_ON 0x10 /* VCC5 Power Supply ON */ - -#define POWER0_DAC_OFF 0x00 /* DAC Power Supply OFF */ -#define POWER0_COM_OFF 0x00 /* COM Power Supply OFF */ -#define POWER0_VCC5_OFF 0x00 /* VCC5 Power Supply OFF */ - -#define PICTRL_INIT_STATE 0x01 -#define PICTRL_INIOFF 0x02 -#define PICTRL_POWER_DOWN 0x04 -#define PICTRL_COM_SIGNAL_OFF 0x08 -#define PICTRL_DAC_SIGNAL_OFF 0x10 - -#define POLCTRL_SYNC_POL_FALL 0x01 -#define POLCTRL_EN_POL_FALL 0x02 -#define POLCTRL_DATA_POL_FALL 0x04 -#define POLCTRL_SYNC_ACT_H 0x08 -#define POLCTRL_EN_ACT_L 0x10 - -#define POLCTRL_SYNC_POL_RISE 0x00 -#define POLCTRL_EN_POL_RISE 0x00 -#define POLCTRL_DATA_POL_RISE 0x00 -#define POLCTRL_SYNC_ACT_L 0x00 -#define POLCTRL_EN_ACT_H 0x00 - -#define PHACTRL_PHASE_MANUAL 0x01 -#define DEFAULT_PHAD_QVGA (9) -#define DEFAULT_COMADJ (125) - -/* - * This is only a psuedo I2C interface. We can't use the standard kernel - * routines as the interface is write only. We just assume the data is acked... - */ -static void lcdtg_ssp_i2c_send(u8 data) -{ - corgi_ssp_lcdtg_send(POWERREG0_ADRS, data); - udelay(10); -} - -static void lcdtg_i2c_send_bit(u8 data) -{ - lcdtg_ssp_i2c_send(data); - lcdtg_ssp_i2c_send(data | POWER0_COM_DCLK); - lcdtg_ssp_i2c_send(data); -} - -static void lcdtg_i2c_send_start(u8 base) -{ - lcdtg_ssp_i2c_send(base | POWER0_COM_DCLK | POWER0_COM_DOUT); - lcdtg_ssp_i2c_send(base | POWER0_COM_DCLK); - lcdtg_ssp_i2c_send(base); -} - -static void lcdtg_i2c_send_stop(u8 base) -{ - lcdtg_ssp_i2c_send(base); - lcdtg_ssp_i2c_send(base | POWER0_COM_DCLK); - lcdtg_ssp_i2c_send(base | POWER0_COM_DCLK | POWER0_COM_DOUT); -} - -static void lcdtg_i2c_send_byte(u8 base, u8 data) -{ - int i; - for (i = 0; i < 8; i++) { - if (data & 0x80) - lcdtg_i2c_send_bit(base | POWER0_COM_DOUT); - else - lcdtg_i2c_send_bit(base); - data <<= 1; - } -} - -static void lcdtg_i2c_wait_ack(u8 base) -{ - lcdtg_i2c_send_bit(base); -} - -static void lcdtg_set_common_voltage(u8 base_data, u8 data) -{ - /* Set Common Voltage to M62332FP via I2C */ - lcdtg_i2c_send_start(base_data); - lcdtg_i2c_send_byte(base_data, 0x9c); - lcdtg_i2c_wait_ack(base_data); - lcdtg_i2c_send_byte(base_data, 0x00); - lcdtg_i2c_wait_ack(base_data); - lcdtg_i2c_send_byte(base_data, data); - lcdtg_i2c_wait_ack(base_data); - lcdtg_i2c_send_stop(base_data); -} - -/* Set Phase Adjust */ -static void lcdtg_set_phadadj(int mode) -{ - int adj; - switch(mode) { - case 480: - case 640: - /* Setting for VGA */ - adj = sharpsl_param.phadadj; - if (adj < 0) { - adj = PHACTRL_PHASE_MANUAL; - } else { - adj = ((adj & 0x0f) << 1) | PHACTRL_PHASE_MANUAL; - } - break; - case 240: - case 320: - default: - /* Setting for QVGA */ - adj = (DEFAULT_PHAD_QVGA << 1) | PHACTRL_PHASE_MANUAL; - break; - } - - corgi_ssp_lcdtg_send(PHACTRL_ADRS, adj); -} - -static int lcd_inited; - -void corgi_lcdtg_hw_init(int mode) -{ - if (!lcd_inited) { - int comadj; - - /* Initialize Internal Logic & Port */ - corgi_ssp_lcdtg_send(PICTRL_ADRS, PICTRL_POWER_DOWN | PICTRL_INIOFF | PICTRL_INIT_STATE - | PICTRL_COM_SIGNAL_OFF | PICTRL_DAC_SIGNAL_OFF); - - corgi_ssp_lcdtg_send(POWERREG0_ADRS, POWER0_COM_DCLK | POWER0_COM_DOUT | POWER0_DAC_OFF - | POWER0_COM_OFF | POWER0_VCC5_OFF); - - corgi_ssp_lcdtg_send(POWERREG1_ADRS, POWER1_VW_OFF | POWER1_GVSS_OFF | POWER1_VDD_OFF); - - /* VDD(+8V), SVSS(-4V) ON */ - corgi_ssp_lcdtg_send(POWERREG1_ADRS, POWER1_VW_OFF | POWER1_GVSS_OFF | POWER1_VDD_ON); - mdelay(3); - - /* DAC ON */ - corgi_ssp_lcdtg_send(POWERREG0_ADRS, POWER0_COM_DCLK | POWER0_COM_DOUT | POWER0_DAC_ON - | POWER0_COM_OFF | POWER0_VCC5_OFF); - - /* INIB = H, INI = L */ - /* PICTL[0] = H , PICTL[1] = PICTL[2] = PICTL[4] = L */ - corgi_ssp_lcdtg_send(PICTRL_ADRS, PICTRL_INIT_STATE | PICTRL_COM_SIGNAL_OFF); - - /* Set Common Voltage */ - comadj = sharpsl_param.comadj; - if (comadj < 0) - comadj = DEFAULT_COMADJ; - lcdtg_set_common_voltage((POWER0_DAC_ON | POWER0_COM_OFF | POWER0_VCC5_OFF), comadj); - - /* VCC5 ON, DAC ON */ - corgi_ssp_lcdtg_send(POWERREG0_ADRS, POWER0_COM_DCLK | POWER0_COM_DOUT | POWER0_DAC_ON | - POWER0_COM_OFF | POWER0_VCC5_ON); - - /* GVSS(-8V) ON, VDD ON */ - corgi_ssp_lcdtg_send(POWERREG1_ADRS, POWER1_VW_OFF | POWER1_GVSS_ON | POWER1_VDD_ON); - mdelay(2); - - /* COM SIGNAL ON (PICTL[3] = L) */ - corgi_ssp_lcdtg_send(PICTRL_ADRS, PICTRL_INIT_STATE); - - /* COM ON, DAC ON, VCC5_ON */ - corgi_ssp_lcdtg_send(POWERREG0_ADRS, POWER0_COM_DCLK | POWER0_COM_DOUT | POWER0_DAC_ON - | POWER0_COM_ON | POWER0_VCC5_ON); - - /* VW ON, GVSS ON, VDD ON */ - corgi_ssp_lcdtg_send(POWERREG1_ADRS, POWER1_VW_ON | POWER1_GVSS_ON | POWER1_VDD_ON); - - /* Signals output enable */ - corgi_ssp_lcdtg_send(PICTRL_ADRS, 0); - - /* Set Phase Adjust */ - lcdtg_set_phadadj(mode); - - /* Initialize for Input Signals from ATI */ - corgi_ssp_lcdtg_send(POLCTRL_ADRS, POLCTRL_SYNC_POL_RISE | POLCTRL_EN_POL_RISE - | POLCTRL_DATA_POL_RISE | POLCTRL_SYNC_ACT_L | POLCTRL_EN_ACT_H); - udelay(1000); - - lcd_inited=1; - } else { - lcdtg_set_phadadj(mode); - } - - switch(mode) { - case 480: - case 640: - /* Set Lcd Resolution (VGA) */ - corgi_ssp_lcdtg_send(RESCTL_ADRS, RESCTL_VGA); - break; - case 240: - case 320: - default: - /* Set Lcd Resolution (QVGA) */ - corgi_ssp_lcdtg_send(RESCTL_ADRS, RESCTL_QVGA); - break; - } -} - -void corgi_lcdtg_suspend(void) -{ - /* 60Hz x 2 frame = 16.7msec x 2 = 33.4 msec */ - mdelay(34); - - /* (1)VW OFF */ - corgi_ssp_lcdtg_send(POWERREG1_ADRS, POWER1_VW_OFF | POWER1_GVSS_ON | POWER1_VDD_ON); - - /* (2)COM OFF */ - corgi_ssp_lcdtg_send(PICTRL_ADRS, PICTRL_COM_SIGNAL_OFF); - corgi_ssp_lcdtg_send(POWERREG0_ADRS, POWER0_DAC_ON | POWER0_COM_OFF | POWER0_VCC5_ON); - - /* (3)Set Common Voltage Bias 0V */ - lcdtg_set_common_voltage(POWER0_DAC_ON | POWER0_COM_OFF | POWER0_VCC5_ON, 0); - - /* (4)GVSS OFF */ - corgi_ssp_lcdtg_send(POWERREG1_ADRS, POWER1_VW_OFF | POWER1_GVSS_OFF | POWER1_VDD_ON); - - /* (5)VCC5 OFF */ - corgi_ssp_lcdtg_send(POWERREG0_ADRS, POWER0_DAC_ON | POWER0_COM_OFF | POWER0_VCC5_OFF); - - /* (6)Set PDWN, INIOFF, DACOFF */ - corgi_ssp_lcdtg_send(PICTRL_ADRS, PICTRL_INIOFF | PICTRL_DAC_SIGNAL_OFF | - PICTRL_POWER_DOWN | PICTRL_COM_SIGNAL_OFF); - - /* (7)DAC OFF */ - corgi_ssp_lcdtg_send(POWERREG0_ADRS, POWER0_DAC_OFF | POWER0_COM_OFF | POWER0_VCC5_OFF); - - /* (8)VDD OFF */ - corgi_ssp_lcdtg_send(POWERREG1_ADRS, POWER1_VW_OFF | POWER1_GVSS_OFF | POWER1_VDD_OFF); - - lcd_inited = 0; -} - diff --git a/arch/arm/mach-pxa/corgi_pm.c b/arch/arm/mach-pxa/corgi_pm.c index 0a85f706e88..eb7d6c94aa4 100644 --- a/arch/arm/mach-pxa/corgi_pm.c +++ b/arch/arm/mach-pxa/corgi_pm.c @@ -20,13 +20,13 @@ #include <asm/irq.h> #include <asm/mach-types.h> -#include <asm/hardware.h> -#include <asm/hardware/scoop.h> +#include <mach/hardware.h> -#include <asm/arch/sharpsl.h> -#include <asm/arch/corgi.h> -#include <asm/arch/pxa-regs.h> -#include <asm/arch/pxa2xx-gpio.h> +#include <mach/sharpsl.h> +#include <mach/corgi.h> +#include <mach/pxa-regs.h> +#include <mach/pxa2xx-regs.h> +#include <mach/pxa2xx-gpio.h> #include "sharpsl.h" #define SHARPSL_CHARGE_ON_VOLT 0x99 /* 2.9V */ @@ -204,7 +204,9 @@ static struct sharpsl_charger_machinfo corgi_pm_machinfo = { .read_devdata = corgipm_read_devdata, .charger_wakeup = corgi_charger_wakeup, .should_wakeup = corgi_should_wakeup, +#ifdef CONFIG_BACKLIGHT_CORGI .backlight_limit = corgibl_limit_intensity, +#endif .charge_on_volt = SHARPSL_CHARGE_ON_VOLT, .charge_on_temp = SHARPSL_CHARGE_ON_TEMP, .charge_acin_high = SHARPSL_CHARGE_ON_ACIN_HIGH, @@ -226,6 +228,10 @@ static int __devinit corgipm_init(void) { int ret; + if (!machine_is_corgi() && !machine_is_shepherd() + && !machine_is_husky()) + return -ENODEV; + corgipm_device = platform_device_alloc("sharpsl-pm", -1); if (!corgipm_device) return -ENOMEM; diff --git a/arch/arm/mach-pxa/corgi_ssp.c b/arch/arm/mach-pxa/corgi_ssp.c deleted file mode 100644 index eccc45d21f7..00000000000 --- a/arch/arm/mach-pxa/corgi_ssp.c +++ /dev/null @@ -1,276 +0,0 @@ -/* - * SSP control code for Sharp Corgi devices - * - * Copyright (c) 2004-2005 Richard Purdie - * - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License version 2 as - * published by the Free Software Foundation. - * - */ - -#include <linux/module.h> -#include <linux/init.h> -#include <linux/kernel.h> -#include <linux/sched.h> -#include <linux/slab.h> -#include <linux/delay.h> -#include <linux/platform_device.h> -#include <asm/hardware.h> -#include <asm/mach-types.h> - -#include <asm/arch/ssp.h> -#include <asm/arch/pxa-regs.h> -#include <asm/arch/pxa2xx-gpio.h> -#include <asm/arch/regs-ssp.h> -#include "sharpsl.h" - -static DEFINE_SPINLOCK(corgi_ssp_lock); -static struct ssp_dev corgi_ssp_dev; -static struct ssp_state corgi_ssp_state; -static struct corgissp_machinfo *ssp_machinfo; - -/* - * There are three devices connected to the SSP interface: - * 1. A touchscreen controller (TI ADS7846 compatible) - * 2. An LCD controller (with some Backlight functionality) - * 3. A battery monitoring IC (Maxim MAX1111) - * - * Each device uses a different speed/mode of communication. - * - * The touchscreen is very sensitive and the most frequently used - * so the port is left configured for this. - * - * Devices are selected using Chip Selects on GPIOs. - */ - -/* - * ADS7846 Routines - */ -unsigned long corgi_ssp_ads7846_putget(ulong data) -{ - unsigned long flag; - u32 ret = 0; - - spin_lock_irqsave(&corgi_ssp_lock, flag); - if (ssp_machinfo->cs_ads7846 >= 0) - GPCR(ssp_machinfo->cs_ads7846) = GPIO_bit(ssp_machinfo->cs_ads7846); - - ssp_write_word(&corgi_ssp_dev,data); - ssp_read_word(&corgi_ssp_dev, &ret); - - if (ssp_machinfo->cs_ads7846 >= 0) - GPSR(ssp_machinfo->cs_ads7846) = GPIO_bit(ssp_machinfo->cs_ads7846); - spin_unlock_irqrestore(&corgi_ssp_lock, flag); - - return ret; -} - -/* - * NOTE: These functions should always be called in interrupt context - * and use the _lock and _unlock functions. They are very time sensitive. - */ -void corgi_ssp_ads7846_lock(void) -{ - spin_lock(&corgi_ssp_lock); - if (ssp_machinfo->cs_ads7846 >= 0) - GPCR(ssp_machinfo->cs_ads7846) = GPIO_bit(ssp_machinfo->cs_ads7846); -} - -void corgi_ssp_ads7846_unlock(void) -{ - if (ssp_machinfo->cs_ads7846 >= 0) - GPSR(ssp_machinfo->cs_ads7846) = GPIO_bit(ssp_machinfo->cs_ads7846); - spin_unlock(&corgi_ssp_lock); -} - -void corgi_ssp_ads7846_put(ulong data) -{ - ssp_write_word(&corgi_ssp_dev,data); -} - -unsigned long corgi_ssp_ads7846_get(void) -{ - u32 ret = 0; - ssp_read_word(&corgi_ssp_dev, &ret); - return ret; -} - -EXPORT_SYMBOL(corgi_ssp_ads7846_putget); -EXPORT_SYMBOL(corgi_ssp_ads7846_lock); -EXPORT_SYMBOL(corgi_ssp_ads7846_unlock); -EXPORT_SYMBOL(corgi_ssp_ads7846_put); -EXPORT_SYMBOL(corgi_ssp_ads7846_get); - - -/* - * LCD/Backlight Routines - */ -unsigned long corgi_ssp_dac_put(ulong data) -{ - unsigned long flag, sscr1 = SSCR1_SPH; - u32 tmp; - - spin_lock_irqsave(&corgi_ssp_lock, flag); - - if (machine_is_spitz() || machine_is_akita() || machine_is_borzoi()) - sscr1 = 0; - - ssp_disable(&corgi_ssp_dev); - ssp_config(&corgi_ssp_dev, (SSCR0_Motorola | (SSCR0_DSS & 0x07 )), sscr1, 0, SSCR0_SerClkDiv(ssp_machinfo->clk_lcdcon)); - ssp_enable(&corgi_ssp_dev); - - if (ssp_machinfo->cs_lcdcon >= 0) - GPCR(ssp_machinfo->cs_lcdcon) = GPIO_bit(ssp_machinfo->cs_lcdcon); - ssp_write_word(&corgi_ssp_dev,data); - /* Read null data back from device to prevent SSP overflow */ - ssp_read_word(&corgi_ssp_dev, &tmp); - if (ssp_machinfo->cs_lcdcon >= 0) - GPSR(ssp_machinfo->cs_lcdcon) = GPIO_bit(ssp_machinfo->cs_lcdcon); - - ssp_disable(&corgi_ssp_dev); - ssp_config(&corgi_ssp_dev, (SSCR0_National | (SSCR0_DSS & 0x0b )), 0, 0, SSCR0_SerClkDiv(ssp_machinfo->clk_ads7846)); - ssp_enable(&corgi_ssp_dev); - - spin_unlock_irqrestore(&corgi_ssp_lock, flag); - - return 0; -} - -void corgi_ssp_lcdtg_send(u8 adrs, u8 data) -{ - corgi_ssp_dac_put(((adrs & 0x07) << 5) | (data & 0x1f)); -} - -void corgi_ssp_blduty_set(int duty) -{ - corgi_ssp_lcdtg_send(0x02,duty); -} - -EXPORT_SYMBOL(corgi_ssp_lcdtg_send); -EXPORT_SYMBOL(corgi_ssp_blduty_set); - -/* - * Max1111 Routines - */ -int corgi_ssp_max1111_get(ulong data) -{ - unsigned long flag; - long voltage = 0, voltage1 = 0, voltage2 = 0; - - spin_lock_irqsave(&corgi_ssp_lock, flag); - if (ssp_machinfo->cs_max1111 >= 0) - GPCR(ssp_machinfo->cs_max1111) = GPIO_bit(ssp_machinfo->cs_max1111); - ssp_disable(&corgi_ssp_dev); - ssp_config(&corgi_ssp_dev, (SSCR0_Motorola | (SSCR0_DSS & 0x07 )), 0, 0, SSCR0_SerClkDiv(ssp_machinfo->clk_max1111)); - ssp_enable(&corgi_ssp_dev); - - udelay(1); - - /* TB1/RB1 */ - ssp_write_word(&corgi_ssp_dev,data); - ssp_read_word(&corgi_ssp_dev, (u32*)&voltage1); /* null read */ - - /* TB12/RB2 */ - ssp_write_word(&corgi_ssp_dev,0); - ssp_read_word(&corgi_ssp_dev, (u32*)&voltage1); - - /* TB13/RB3*/ - ssp_write_word(&corgi_ssp_dev,0); - ssp_read_word(&corgi_ssp_dev, (u32*)&voltage2); - - ssp_disable(&corgi_ssp_dev); - ssp_config(&corgi_ssp_dev, (SSCR0_National | (SSCR0_DSS & 0x0b )), 0, 0, SSCR0_SerClkDiv(ssp_machinfo->clk_ads7846)); - ssp_enable(&corgi_ssp_dev); - if (ssp_machinfo->cs_max1111 >= 0) - GPSR(ssp_machinfo->cs_max1111) = GPIO_bit(ssp_machinfo->cs_max1111); - spin_unlock_irqrestore(&corgi_ssp_lock, flag); - - if (voltage1 & 0xc0 || voltage2 & 0x3f) - voltage = -1; - else - voltage = ((voltage1 << 2) & 0xfc) | ((voltage2 >> 6) & 0x03); - - return voltage; -} - -EXPORT_SYMBOL(corgi_ssp_max1111_get); - -/* - * Support Routines - */ - -void __init corgi_ssp_set_machinfo(struct corgissp_machinfo *machinfo) -{ - ssp_machinfo = machinfo; -} - -static int __init corgi_ssp_probe(struct platform_device *dev) -{ - int ret; - - /* Chip Select - Disable All */ - if (ssp_machinfo->cs_lcdcon >= 0) - pxa_gpio_mode(ssp_machinfo->cs_lcdcon | GPIO_OUT | GPIO_DFLT_HIGH); - if (ssp_machinfo->cs_max1111 >= 0) - pxa_gpio_mode(ssp_machinfo->cs_max1111 | GPIO_OUT | GPIO_DFLT_HIGH); - if (ssp_machinfo->cs_ads7846 >= 0) - pxa_gpio_mode(ssp_machinfo->cs_ads7846 | GPIO_OUT | GPIO_DFLT_HIGH); - - ret = ssp_init(&corgi_ssp_dev, ssp_machinfo->port, 0); - - if (ret) - printk(KERN_ERR "Unable to register SSP handler!\n"); - else { - ssp_disable(&corgi_ssp_dev); - ssp_config(&corgi_ssp_dev, (SSCR0_National | (SSCR0_DSS & 0x0b )), 0, 0, SSCR0_SerClkDiv(ssp_machinfo->clk_ads7846)); - ssp_enable(&corgi_ssp_dev); - } - - return ret; -} - -static int corgi_ssp_remove(struct platform_device *dev) -{ - ssp_exit(&corgi_ssp_dev); - return 0; -} - -static int corgi_ssp_suspend(struct platform_device *dev, pm_message_t state) -{ - ssp_flush(&corgi_ssp_dev); - ssp_save_state(&corgi_ssp_dev,&corgi_ssp_state); - - return 0; -} - -static int corgi_ssp_resume(struct platform_device *dev) -{ - if (ssp_machinfo->cs_lcdcon >= 0) - GPSR(ssp_machinfo->cs_lcdcon) = GPIO_bit(ssp_machinfo->cs_lcdcon); /* High - Disable LCD Control/Timing Gen */ - if (ssp_machinfo->cs_max1111 >= 0) - GPSR(ssp_machinfo->cs_max1111) = GPIO_bit(ssp_machinfo->cs_max1111); /* High - Disable MAX1111*/ - if (ssp_machinfo->cs_ads7846 >= 0) - GPSR(ssp_machinfo->cs_ads7846) = GPIO_bit(ssp_machinfo->cs_ads7846); /* High - Disable ADS7846*/ - ssp_restore_state(&corgi_ssp_dev,&corgi_ssp_state); - ssp_enable(&corgi_ssp_dev); - - return 0; -} - -static struct platform_driver corgissp_driver = { - .probe = corgi_ssp_probe, - .remove = corgi_ssp_remove, - .suspend = corgi_ssp_suspend, - .resume = corgi_ssp_resume, - .driver = { - .name = "corgi-ssp", - }, -}; - -int __init corgi_ssp_init(void) -{ - return platform_driver_register(&corgissp_driver); -} - -arch_initcall(corgi_ssp_init); diff --git a/arch/arm/mach-pxa/cpu-pxa.c b/arch/arm/mach-pxa/cpufreq-pxa2xx.c index fb9ba1ab282..d82528e74bd 100644 --- a/arch/arm/mach-pxa/cpu-pxa.c +++ b/arch/arm/mach-pxa/cpufreq-pxa2xx.c @@ -1,5 +1,5 @@ /* - * linux/arch/arm/mach-pxa/cpu-pxa.c + * linux/arch/arm/mach-pxa/cpufreq-pxa2xx.c * * Copyright (C) 2002,2003 Intrinsyc Software * @@ -37,9 +37,9 @@ #include <linux/init.h> #include <linux/cpufreq.h> -#include <asm/hardware.h> -#include <asm/arch/pxa-regs.h> -#include <asm/arch/pxa2xx-regs.h> +#include <mach/hardware.h> +#include <mach/pxa-regs.h> +#include <mach/pxa2xx-regs.h> #ifdef DEBUG static unsigned int freq_debug; diff --git a/arch/arm/mach-pxa/cpufreq-pxa3xx.c b/arch/arm/mach-pxa/cpufreq-pxa3xx.c new file mode 100644 index 00000000000..1ea0c9c0ada --- /dev/null +++ b/arch/arm/mach-pxa/cpufreq-pxa3xx.c @@ -0,0 +1,258 @@ +/* + * linux/arch/arm/mach-pxa/cpufreq-pxa3xx.c + * + * Copyright (C) 2008 Marvell International Ltd. + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + */ + +#include <linux/kernel.h> +#include <linux/module.h> +#include <linux/sched.h> +#include <linux/init.h> +#include <linux/cpufreq.h> + +#include <mach/hardware.h> +#include <mach/pxa-regs.h> +#include <mach/pxa3xx-regs.h> + +#include "generic.h" + +#define HSS_104M (0) +#define HSS_156M (1) +#define HSS_208M (2) +#define HSS_312M (3) + +#define SMCFS_78M (0) +#define SMCFS_104M (2) +#define SMCFS_208M (5) + +#define SFLFS_104M (0) +#define SFLFS_156M (1) +#define SFLFS_208M (2) +#define SFLFS_312M (3) + +#define XSPCLK_156M (0) +#define XSPCLK_NONE (3) + +#define DMCFS_26M (0) +#define DMCFS_260M (3) + +struct pxa3xx_freq_info { + unsigned int cpufreq_mhz; + unsigned int core_xl : 5; + unsigned int core_xn : 3; + unsigned int hss : 2; + unsigned int dmcfs : 2; + unsigned int smcfs : 3; + unsigned int sflfs : 2; + unsigned int df_clkdiv : 3; + + int vcc_core; /* in mV */ + int vcc_sram; /* in mV */ +}; + +#define OP(cpufreq, _xl, _xn, _hss, _dmc, _smc, _sfl, _dfi, vcore, vsram) \ +{ \ + .cpufreq_mhz = cpufreq, \ + .core_xl = _xl, \ + .core_xn = _xn, \ + .hss = HSS_##_hss##M, \ + .dmcfs = DMCFS_##_dmc##M, \ + .smcfs = SMCFS_##_smc##M, \ + .sflfs = SFLFS_##_sfl##M, \ + .df_clkdiv = _dfi, \ + .vcc_core = vcore, \ + .vcc_sram = vsram, \ +} + +static struct pxa3xx_freq_info pxa300_freqs[] = { + /* CPU XL XN HSS DMEM SMEM SRAM DFI VCC_CORE VCC_SRAM */ + OP(104, 8, 1, 104, 260, 78, 104, 3, 1000, 1100), /* 104MHz */ + OP(208, 16, 1, 104, 260, 104, 156, 2, 1000, 1100), /* 208MHz */ + OP(416, 16, 2, 156, 260, 104, 208, 2, 1100, 1200), /* 416MHz */ + OP(624, 24, 2, 208, 260, 208, 312, 3, 1375, 1400), /* 624MHz */ +}; + +static struct pxa3xx_freq_info pxa320_freqs[] = { + /* CPU XL XN HSS DMEM SMEM SRAM DFI VCC_CORE VCC_SRAM */ + OP(104, 8, 1, 104, 260, 78, 104, 3, 1000, 1100), /* 104MHz */ + OP(208, 16, 1, 104, 260, 104, 156, 2, 1000, 1100), /* 208MHz */ + OP(416, 16, 2, 156, 260, 104, 208, 2, 1100, 1200), /* 416MHz */ + OP(624, 24, 2, 208, 260, 208, 312, 3, 1375, 1400), /* 624MHz */ + OP(806, 31, 2, 208, 260, 208, 312, 3, 1400, 1400), /* 806MHz */ +}; + +static unsigned int pxa3xx_freqs_num; +static struct pxa3xx_freq_info *pxa3xx_freqs; +static struct cpufreq_frequency_table *pxa3xx_freqs_table; + +static int setup_freqs_table(struct cpufreq_policy *policy, + struct pxa3xx_freq_info *freqs, int num) +{ + struct cpufreq_frequency_table *table; + int i; + + table = kzalloc((num + 1) * sizeof(*table), GFP_KERNEL); + if (table == NULL) + return -ENOMEM; + + for (i = 0; i < num; i++) { + table[i].index = i; + table[i].frequency = freqs[i].cpufreq_mhz * 1000; + } + table[num].frequency = i; + table[num].frequency = CPUFREQ_TABLE_END; + + pxa3xx_freqs = freqs; + pxa3xx_freqs_num = num; + pxa3xx_freqs_table = table; + + return cpufreq_frequency_table_cpuinfo(policy, table); +} + +static void __update_core_freq(struct pxa3xx_freq_info *info) +{ + uint32_t mask = ACCR_XN_MASK | ACCR_XL_MASK; + uint32_t accr = ACCR; + uint32_t xclkcfg; + + accr &= ~(ACCR_XN_MASK | ACCR_XL_MASK | ACCR_XSPCLK_MASK); + accr |= ACCR_XN(info->core_xn) | ACCR_XL(info->core_xl); + + /* No clock until core PLL is re-locked */ + accr |= ACCR_XSPCLK(XSPCLK_NONE); + + xclkcfg = (info->core_xn == 2) ? 0x3 : 0x2; /* turbo bit */ + + ACCR = accr; + __asm__("mcr p14, 0, %0, c6, c0, 0\n" : : "r"(xclkcfg)); + + while ((ACSR & mask) != (accr & mask)) + cpu_relax(); +} + +static void __update_bus_freq(struct pxa3xx_freq_info *info) +{ + uint32_t mask; + uint32_t accr = ACCR; + + mask = ACCR_SMCFS_MASK | ACCR_SFLFS_MASK | ACCR_HSS_MASK | + ACCR_DMCFS_MASK; + + accr &= ~mask; + accr |= ACCR_SMCFS(info->smcfs) | ACCR_SFLFS(info->sflfs) | + ACCR_HSS(info->hss) | ACCR_DMCFS(info->dmcfs); + + ACCR = accr; + + while ((ACSR & mask) != (accr & mask)) + cpu_relax(); +} + +static int pxa3xx_cpufreq_verify(struct cpufreq_policy *policy) +{ + return cpufreq_frequency_table_verify(policy, pxa3xx_freqs_table); +} + +static unsigned int pxa3xx_cpufreq_get(unsigned int cpu) +{ + return get_clk_frequency_khz(0); +} + +static int pxa3xx_cpufreq_set(struct cpufreq_policy *policy, + unsigned int target_freq, + unsigned int relation) +{ + struct pxa3xx_freq_info *next; + struct cpufreq_freqs freqs; + unsigned long flags; + int idx; + + if (policy->cpu != 0) + return -EINVAL; + + /* Lookup the next frequency */ + if (cpufreq_frequency_table_target(policy, pxa3xx_freqs_table, + target_freq, relation, &idx)) + return -EINVAL; + + next = &pxa3xx_freqs[idx]; + + freqs.old = policy->cur; + freqs.new = next->cpufreq_mhz * 1000; + freqs.cpu = policy->cpu; + + pr_debug("CPU frequency from %d MHz to %d MHz%s\n", + freqs.old / 1000, freqs.new / 1000, + (freqs.old == freqs.new) ? " (skipped)" : ""); + + if (freqs.old == target_freq) + return 0; + + cpufreq_notify_transition(&freqs, CPUFREQ_PRECHANGE); + + local_irq_save(flags); + __update_core_freq(next); + __update_bus_freq(next); + local_irq_restore(flags); + + cpufreq_notify_transition(&freqs, CPUFREQ_POSTCHANGE); + + return 0; +} + +static __init int pxa3xx_cpufreq_init(struct cpufreq_policy *policy) +{ + int ret = -EINVAL; + + /* set default policy and cpuinfo */ + policy->governor = CPUFREQ_DEFAULT_GOVERNOR; + policy->cpuinfo.min_freq = 104000; + policy->cpuinfo.max_freq = (cpu_is_pxa320()) ? 806000 : 624000; + policy->cpuinfo.transition_latency = 1000; /* FIXME: 1 ms, assumed */ + policy->cur = policy->min = policy->max = get_clk_frequency_khz(0); + + if (cpu_is_pxa300() || cpu_is_pxa310()) + ret = setup_freqs_table(policy, ARRAY_AND_SIZE(pxa300_freqs)); + + if (cpu_is_pxa320()) + ret = setup_freqs_table(policy, ARRAY_AND_SIZE(pxa320_freqs)); + + if (ret) { + pr_err("failed to setup frequency table\n"); + return ret; + } + + pr_info("CPUFREQ support for PXA3xx initialized\n"); + return 0; +} + +static struct cpufreq_driver pxa3xx_cpufreq_driver = { + .verify = pxa3xx_cpufreq_verify, + .target = pxa3xx_cpufreq_set, + .init = pxa3xx_cpufreq_init, + .get = pxa3xx_cpufreq_get, + .name = "pxa3xx-cpufreq", +}; + +static int __init cpufreq_init(void) +{ + if (cpu_is_pxa3xx()) + return cpufreq_register_driver(&pxa3xx_cpufreq_driver); + + return 0; +} +module_init(cpufreq_init); + +static void __exit cpufreq_exit(void) +{ + cpufreq_unregister_driver(&pxa3xx_cpufreq_driver); +} +module_exit(cpufreq_exit); + +MODULE_DESCRIPTION("CPU frequency scaling driver for PXA3xx"); +MODULE_LICENSE("GPL"); diff --git a/arch/arm/mach-pxa/devices.c b/arch/arm/mach-pxa/devices.c index d6c05b6eab3..35736fc0863 100644 --- a/arch/arm/mach-pxa/devices.c +++ b/arch/arm/mach-pxa/devices.c @@ -4,17 +4,22 @@ #include <linux/platform_device.h> #include <linux/dma-mapping.h> -#include <asm/arch/gpio.h> -#include <asm/arch/udc.h> -#include <asm/arch/pxafb.h> -#include <asm/arch/mmc.h> -#include <asm/arch/irda.h> -#include <asm/arch/i2c.h> -#include <asm/arch/ohci.h> -#include <asm/arch/pxa27x_keypad.h> -#include <asm/arch/camera.h> +#include <mach/gpio.h> +#include <mach/udc.h> +#include <mach/pxafb.h> +#include <mach/mmc.h> +#include <mach/irda.h> +#include <mach/i2c.h> +#include <mach/mfp-pxa27x.h> +#include <mach/ohci.h> +#include <mach/pxa27x_keypad.h> +#include <mach/pxa2xx_spi.h> +#include <mach/camera.h> +#include <mach/audio.h> +#include <mach/pxa3xx_nand.h> #include "devices.h" +#include "generic.h" void __init pxa_register_device(struct platform_device *dev, void *data) { @@ -91,8 +96,19 @@ static struct resource pxa2xx_udc_resources[] = { static u64 udc_dma_mask = ~(u32)0; -struct platform_device pxa_device_udc = { - .name = "pxa2xx-udc", +struct platform_device pxa25x_device_udc = { + .name = "pxa25x-udc", + .id = -1, + .resource = pxa2xx_udc_resources, + .num_resources = ARRAY_SIZE(pxa2xx_udc_resources), + .dev = { + .platform_data = &pxa_udc_info, + .dma_mask = &udc_dma_mask, + } +}; + +struct platform_device pxa27x_device_udc = { + .name = "pxa27x-udc", .id = -1, .resource = pxa2xx_udc_resources, .num_resources = ARRAY_SIZE(pxa2xx_udc_resources), @@ -233,8 +249,15 @@ struct platform_device pxa_device_i2c = { .num_resources = ARRAY_SIZE(pxai2c_resources), }; +static unsigned long pxa27x_i2c_mfp_cfg[] = { + GPIO117_I2C_SCL, + GPIO118_I2C_SDA, +}; + void __init pxa_set_i2c_info(struct i2c_pxa_platform_data *info) { + if (cpu_is_pxa27x()) + pxa2xx_mfp_config(ARRAY_AND_SIZE(pxa27x_i2c_mfp_cfg)); pxa_register_device(&pxa_device_i2c, info); } @@ -278,8 +301,69 @@ struct platform_device pxa_device_rtc = { .id = -1, }; +static struct resource pxa_ac97_resources[] = { + [0] = { + .start = 0x40500000, + .end = 0x40500000 + 0xfff, + .flags = IORESOURCE_MEM, + }, + [1] = { + .start = IRQ_AC97, + .end = IRQ_AC97, + .flags = IORESOURCE_IRQ, + }, +}; + +static u64 pxa_ac97_dmamask = 0xffffffffUL; + +struct platform_device pxa_device_ac97 = { + .name = "pxa2xx-ac97", + .id = -1, + .dev = { + .dma_mask = &pxa_ac97_dmamask, + .coherent_dma_mask = 0xffffffff, + }, + .num_resources = ARRAY_SIZE(pxa_ac97_resources), + .resource = pxa_ac97_resources, +}; + +void __init pxa_set_ac97_info(pxa2xx_audio_ops_t *ops) +{ + pxa_register_device(&pxa_device_ac97, ops); +} + #ifdef CONFIG_PXA25x +static struct resource pxa25x_resource_pwm0[] = { + [0] = { + .start = 0x40b00000, + .end = 0x40b0000f, + .flags = IORESOURCE_MEM, + }, +}; + +struct platform_device pxa25x_device_pwm0 = { + .name = "pxa25x-pwm", + .id = 0, + .resource = pxa25x_resource_pwm0, + .num_resources = ARRAY_SIZE(pxa25x_resource_pwm0), +}; + +static struct resource pxa25x_resource_pwm1[] = { + [0] = { + .start = 0x40c00000, + .end = 0x40c0000f, + .flags = IORESOURCE_MEM, + }, +}; + +struct platform_device pxa25x_device_pwm1 = { + .name = "pxa25x-pwm", + .id = 1, + .resource = pxa25x_resource_pwm1, + .num_resources = ARRAY_SIZE(pxa25x_resource_pwm1), +}; + static u64 pxa25x_ssp_dma_mask = DMA_BIT_MASK(32); static struct resource pxa25x_resource_ssp[] = { @@ -568,6 +652,36 @@ struct platform_device pxa27x_device_ssp3 = { .num_resources = ARRAY_SIZE(pxa27x_resource_ssp3), }; +static struct resource pxa27x_resource_pwm0[] = { + [0] = { + .start = 0x40b00000, + .end = 0x40b0001f, + .flags = IORESOURCE_MEM, + }, +}; + +struct platform_device pxa27x_device_pwm0 = { + .name = "pxa27x-pwm", + .id = 0, + .resource = pxa27x_resource_pwm0, + .num_resources = ARRAY_SIZE(pxa27x_resource_pwm0), +}; + +static struct resource pxa27x_resource_pwm1[] = { + [0] = { + .start = 0x40c00000, + .end = 0x40c0001f, + .flags = IORESOURCE_MEM, + }, +}; + +struct platform_device pxa27x_device_pwm1 = { + .name = "pxa27x-pwm", + .id = 1, + .resource = pxa27x_resource_pwm1, + .num_resources = ARRAY_SIZE(pxa27x_resource_pwm1), +}; + static struct resource pxa27x_resource_camera[] = { [0] = { .start = 0x50000000, @@ -718,4 +832,63 @@ void __init pxa3xx_set_mci3_info(struct pxamci_platform_data *info) pxa_register_device(&pxa3xx_device_mci3, info); } +static struct resource pxa3xx_resources_nand[] = { + [0] = { + .start = 0x43100000, + .end = 0x43100053, + .flags = IORESOURCE_MEM, + }, + [1] = { + .start = IRQ_NAND, + .end = IRQ_NAND, + .flags = IORESOURCE_IRQ, + }, + [2] = { + /* DRCMR for Data DMA */ + .start = 97, + .end = 97, + .flags = IORESOURCE_DMA, + }, + [3] = { + /* DRCMR for Command DMA */ + .start = 99, + .end = 99, + .flags = IORESOURCE_DMA, + }, +}; + +static u64 pxa3xx_nand_dma_mask = DMA_BIT_MASK(32); + +struct platform_device pxa3xx_device_nand = { + .name = "pxa3xx-nand", + .id = -1, + .dev = { + .dma_mask = &pxa3xx_nand_dma_mask, + .coherent_dma_mask = DMA_BIT_MASK(32), + }, + .num_resources = ARRAY_SIZE(pxa3xx_resources_nand), + .resource = pxa3xx_resources_nand, +}; + +void __init pxa3xx_set_nand_info(struct pxa3xx_nand_platform_data *info) +{ + pxa_register_device(&pxa3xx_device_nand, info); +} #endif /* CONFIG_PXA3xx */ + +/* pxa2xx-spi platform-device ID equals respective SSP platform-device ID + 1. + * See comment in arch/arm/mach-pxa/ssp.c::ssp_probe() */ +void __init pxa2xx_set_spi_info(unsigned id, struct pxa2xx_spi_master *info) +{ + struct platform_device *pd; + + pd = platform_device_alloc("pxa2xx-spi", id); + if (pd == NULL) { + printk(KERN_ERR "pxa2xx-spi: failed to allocate device id %d\n", + id); + return; + } + + pd->dev.platform_data = info; + platform_device_add(pd); +} diff --git a/arch/arm/mach-pxa/devices.h b/arch/arm/mach-pxa/devices.h index fcab017f27e..bb04af4b0aa 100644 --- a/arch/arm/mach-pxa/devices.h +++ b/arch/arm/mach-pxa/devices.h @@ -1,7 +1,8 @@ extern struct platform_device pxa_device_mci; extern struct platform_device pxa3xx_device_mci2; extern struct platform_device pxa3xx_device_mci3; -extern struct platform_device pxa_device_udc; +extern struct platform_device pxa25x_device_udc; +extern struct platform_device pxa27x_device_udc; extern struct platform_device pxa_device_fb; extern struct platform_device pxa_device_ffuart; extern struct platform_device pxa_device_btuart; @@ -11,6 +12,7 @@ extern struct platform_device pxa_device_i2c; extern struct platform_device pxa_device_i2s; extern struct platform_device pxa_device_ficp; extern struct platform_device pxa_device_rtc; +extern struct platform_device pxa_device_ac97; extern struct platform_device pxa27x_device_i2c_power; extern struct platform_device pxa27x_device_ohci; @@ -24,4 +26,12 @@ extern struct platform_device pxa27x_device_ssp2; extern struct platform_device pxa27x_device_ssp3; extern struct platform_device pxa3xx_device_ssp4; +extern struct platform_device pxa25x_device_pwm0; +extern struct platform_device pxa25x_device_pwm1; +extern struct platform_device pxa27x_device_pwm0; +extern struct platform_device pxa27x_device_pwm1; + +extern struct platform_device pxa3xx_device_nand; +extern struct platform_device pxa3xx_device_i2c_power; + void __init pxa_register_device(struct platform_device *dev, void *data); diff --git a/arch/arm/mach-pxa/dma.c b/arch/arm/mach-pxa/dma.c index 3215316d7b0..c0be17e0ab8 100644 --- a/arch/arm/mach-pxa/dma.c +++ b/arch/arm/mach-pxa/dma.c @@ -20,10 +20,10 @@ #include <asm/system.h> #include <asm/irq.h> -#include <asm/hardware.h> +#include <mach/hardware.h> #include <asm/dma.h> -#include <asm/arch/pxa-regs.h> +#include <mach/pxa-regs.h> struct dma_channel { char *name; diff --git a/arch/arm/mach-pxa/e330.c b/arch/arm/mach-pxa/e330.c new file mode 100644 index 00000000000..d488eded205 --- /dev/null +++ b/arch/arm/mach-pxa/e330.c @@ -0,0 +1,43 @@ +/* + * Hardware definitions for the Toshiba eseries PDAs + * + * Copyright (c) 2003 Ian Molton <spyro@f2s.com> + * + * This file is licensed under + * the terms of the GNU General Public License version 2. This program + * is licensed "as is" without any warranty of any kind, whether express + * or implied. + * + */ + +#include <linux/kernel.h> +#include <linux/init.h> + +#include <asm/setup.h> +#include <asm/mach/arch.h> +#include <asm/mach-types.h> + +#include <mach/mfp-pxa25x.h> +#include <mach/hardware.h> +#include <mach/udc.h> + +#include "generic.h" +#include "eseries.h" + +static void __init e330_init(void) +{ + pxa_set_udc_info(&e7xx_udc_mach_info); +} + +MACHINE_START(E330, "Toshiba e330") + /* Maintainer: Ian Molton (spyro@f2s.com) */ + .phys_io = 0x40000000, + .io_pg_offst = (io_p2v(0x40000000) >> 18) & 0xfffc, + .boot_params = 0xa0000100, + .map_io = pxa_map_io, + .init_irq = pxa25x_init_irq, + .fixup = eseries_fixup, + .init_machine = e330_init, + .timer = &pxa_timer, +MACHINE_END + diff --git a/arch/arm/mach-pxa/e350.c b/arch/arm/mach-pxa/e350.c new file mode 100644 index 00000000000..8ecbc547982 --- /dev/null +++ b/arch/arm/mach-pxa/e350.c @@ -0,0 +1,43 @@ +/* + * Hardware definitions for the Toshiba eseries PDAs + * + * Copyright (c) 2003 Ian Molton <spyro@f2s.com> + * + * This file is licensed under + * the terms of the GNU General Public License version 2. This program + * is licensed "as is" without any warranty of any kind, whether express + * or implied. + * + */ + +#include <linux/kernel.h> +#include <linux/init.h> + +#include <asm/setup.h> +#include <asm/mach/arch.h> +#include <asm/mach-types.h> + +#include <mach/mfp-pxa25x.h> +#include <mach/hardware.h> +#include <mach/udc.h> + +#include "generic.h" +#include "eseries.h" + +static void __init e350_init(void) +{ + pxa_set_udc_info(&e7xx_udc_mach_info); +} + +MACHINE_START(E350, "Toshiba e350") + /* Maintainer: Ian Molton (spyro@f2s.com) */ + .phys_io = 0x40000000, + .io_pg_offst = (io_p2v(0x40000000) >> 18) & 0xfffc, + .boot_params = 0xa0000100, + .map_io = pxa_map_io, + .init_irq = pxa25x_init_irq, + .fixup = eseries_fixup, + .init_machine = e350_init, + .timer = &pxa_timer, +MACHINE_END + diff --git a/arch/arm/mach-pxa/e400.c b/arch/arm/mach-pxa/e400.c new file mode 100644 index 00000000000..544bbaa2062 --- /dev/null +++ b/arch/arm/mach-pxa/e400.c @@ -0,0 +1,94 @@ +/* + * Hardware definitions for the Toshiba eseries PDAs + * + * Copyright (c) 2003 Ian Molton <spyro@f2s.com> + * + * This file is licensed under + * the terms of the GNU General Public License version 2. This program + * is licensed "as is" without any warranty of any kind, whether express + * or implied. + * + */ + +#include <linux/kernel.h> +#include <linux/init.h> + +#include <asm/setup.h> +#include <asm/mach/arch.h> +#include <asm/mach-types.h> + +#include <mach/pxa-regs.h> +#include <mach/mfp-pxa25x.h> +#include <mach/hardware.h> + +#include <mach/pxafb.h> +#include <mach/udc.h> + +#include "generic.h" +#include "eseries.h" + +/* ------------------------ E400 LCD definitions ------------------------ */ + +static struct pxafb_mode_info e400_pxafb_mode_info = { + .pixclock = 140703, + .xres = 240, + .yres = 320, + .bpp = 16, + .hsync_len = 4, + .left_margin = 28, + .right_margin = 8, + .vsync_len = 3, + .upper_margin = 5, + .lower_margin = 6, + .sync = 0, +}; + +static struct pxafb_mach_info e400_pxafb_mach_info = { + .modes = &e400_pxafb_mode_info, + .num_modes = 1, + .lccr0 = LCCR0_Color | LCCR0_Sngl | LCCR0_Act, + .lccr3 = 0, + .pxafb_backlight_power = NULL, +}; + +/* ------------------------ E400 MFP config ----------------------------- */ + +static unsigned long e400_pin_config[] __initdata = { + /* Chip selects */ + GPIO15_nCS_1, /* CS1 - Flash */ + GPIO80_nCS_4, /* CS4 - TMIO */ + + /* Clocks */ + GPIO12_32KHz, + + /* BTUART */ + GPIO42_BTUART_RXD, + GPIO43_BTUART_TXD, + GPIO44_BTUART_CTS, + GPIO45_GPIO, /* Used by TMIO for #SUSPEND */ + + /* wakeup */ + GPIO0_GPIO | WAKEUP_ON_EDGE_RISE, +}; + +/* ---------------------------------------------------------------------- */ + +static void __init e400_init(void) +{ + pxa2xx_mfp_config(ARRAY_AND_SIZE(e400_pin_config)); + set_pxa_fb_info(&e400_pxafb_mach_info); + pxa_set_udc_info(&e7xx_udc_mach_info); +} + +MACHINE_START(E400, "Toshiba e400") + /* Maintainer: Ian Molton (spyro@f2s.com) */ + .phys_io = 0x40000000, + .io_pg_offst = (io_p2v(0x40000000) >> 18) & 0xfffc, + .boot_params = 0xa0000100, + .map_io = pxa_map_io, + .init_irq = pxa25x_init_irq, + .fixup = eseries_fixup, + .init_machine = e400_init, + .timer = &pxa_timer, +MACHINE_END + diff --git a/arch/arm/mach-pxa/e740.c b/arch/arm/mach-pxa/e740.c new file mode 100644 index 00000000000..c57a15b37f0 --- /dev/null +++ b/arch/arm/mach-pxa/e740.c @@ -0,0 +1,169 @@ +/* + * Hardware definitions for the Toshiba eseries PDAs + * + * Copyright (c) 2003 Ian Molton <spyro@f2s.com> + * + * This file is licensed under + * the terms of the GNU General Public License version 2. This program + * is licensed "as is" without any warranty of any kind, whether express + * or implied. + * + */ + +#include <linux/kernel.h> +#include <linux/init.h> +#include <linux/device.h> +#include <linux/platform_device.h> +#include <linux/fb.h> + +#include <video/w100fb.h> + +#include <asm/setup.h> +#include <asm/mach/arch.h> +#include <asm/mach-types.h> + +#include <mach/mfp-pxa25x.h> +#include <mach/hardware.h> +#include <mach/udc.h> + +#include "generic.h" +#include "eseries.h" + + +/* ------------------------ e740 video support --------------------------- */ + +static struct w100_gen_regs e740_lcd_regs = { + .lcd_format = 0x00008023, + .lcdd_cntl1 = 0x0f000000, + .lcdd_cntl2 = 0x0003ffff, + .genlcd_cntl1 = 0x00ffff03, + .genlcd_cntl2 = 0x003c0f03, + .genlcd_cntl3 = 0x000143aa, +}; + +static struct w100_mode e740_lcd_mode = { + .xres = 240, + .yres = 320, + .left_margin = 20, + .right_margin = 28, + .upper_margin = 9, + .lower_margin = 8, + .crtc_ss = 0x80140013, + .crtc_ls = 0x81150110, + .crtc_gs = 0x80050005, + .crtc_vpos_gs = 0x000a0009, + .crtc_rev = 0x0040010a, + .crtc_dclk = 0xa906000a, + .crtc_gclk = 0x80050108, + .crtc_goe = 0x80050108, + .pll_freq = 57, + .pixclk_divider = 4, + .pixclk_divider_rotated = 4, + .pixclk_src = CLK_SRC_XTAL, + .sysclk_divider = 1, + .sysclk_src = CLK_SRC_PLL, + .crtc_ps1_active = 0x41060010, +}; + +static struct w100_gpio_regs e740_w100_gpio_info = { + .init_data1 = 0x21002103, + .gpio_dir1 = 0xffffdeff, + .gpio_oe1 = 0x03c00643, + .init_data2 = 0x003f003f, + .gpio_dir2 = 0xffffffff, + .gpio_oe2 = 0x000000ff, +}; + +static struct w100fb_mach_info e740_fb_info = { + .modelist = &e740_lcd_mode, + .num_modes = 1, + .regs = &e740_lcd_regs, + .gpio = &e740_w100_gpio_info, + .xtal_freq = 14318000, + .xtal_dbl = 1, +}; + +static struct resource e740_fb_resources[] = { + [0] = { + .start = 0x0c000000, + .end = 0x0cffffff, + .flags = IORESOURCE_MEM, + }, +}; + +static struct platform_device e740_fb_device = { + .name = "w100fb", + .id = -1, + .dev = { + .platform_data = &e740_fb_info, + }, + .num_resources = ARRAY_SIZE(e740_fb_resources), + .resource = e740_fb_resources, +}; + +/* --------------------------- MFP Pin config -------------------------- */ + +static unsigned long e740_pin_config[] __initdata = { + /* Chip selects */ + GPIO15_nCS_1, /* CS1 - Flash */ + GPIO79_nCS_3, /* CS3 - IMAGEON */ + GPIO80_nCS_4, /* CS4 - TMIO */ + + /* Clocks */ + GPIO12_32KHz, + + /* BTUART */ + GPIO42_BTUART_RXD, + GPIO43_BTUART_TXD, + GPIO44_BTUART_CTS, + GPIO45_GPIO, /* Used by TMIO for #SUSPEND */ + + /* PC Card */ + GPIO8_GPIO, /* CD0 */ + GPIO44_GPIO, /* CD1 */ + GPIO11_GPIO, /* IRQ0 */ + GPIO6_GPIO, /* IRQ1 */ + GPIO27_GPIO, /* RST0 */ + GPIO24_GPIO, /* RST1 */ + GPIO20_GPIO, /* PWR0 */ + GPIO23_GPIO, /* PWR1 */ + GPIO48_nPOE, + GPIO49_nPWE, + GPIO50_nPIOR, + GPIO51_nPIOW, + GPIO52_nPCE_1, + GPIO53_nPCE_2, + GPIO54_nPSKTSEL, + GPIO55_nPREG, + GPIO56_nPWAIT, + GPIO57_nIOIS16, + + /* wakeup */ + GPIO0_GPIO | WAKEUP_ON_EDGE_RISE, +}; + +/* ----------------------------------------------------------------------- */ + +static struct platform_device *devices[] __initdata = { + &e740_fb_device, +}; + +static void __init e740_init(void) +{ + pxa2xx_mfp_config(ARRAY_AND_SIZE(e740_pin_config)); + platform_add_devices(devices, ARRAY_SIZE(devices)); + pxa_set_udc_info(&e7xx_udc_mach_info); +} + +MACHINE_START(E740, "Toshiba e740") + /* Maintainer: Ian Molton (spyro@f2s.com) */ + .phys_io = 0x40000000, + .io_pg_offst = (io_p2v(0x40000000) >> 18) & 0xfffc, + .boot_params = 0xa0000100, + .map_io = pxa_map_io, + .init_irq = pxa25x_init_irq, + .fixup = eseries_fixup, + .init_machine = e740_init, + .timer = &pxa_timer, +MACHINE_END + diff --git a/arch/arm/mach-pxa/e750.c b/arch/arm/mach-pxa/e750.c new file mode 100644 index 00000000000..640e738b85d --- /dev/null +++ b/arch/arm/mach-pxa/e750.c @@ -0,0 +1,126 @@ +/* + * Hardware definitions for the Toshiba eseries PDAs + * + * Copyright (c) 2003 Ian Molton <spyro@f2s.com> + * + * This file is licensed under + * the terms of the GNU General Public License version 2. This program + * is licensed "as is" without any warranty of any kind, whether express + * or implied. + * + */ + +#include <linux/kernel.h> +#include <linux/init.h> +#include <linux/device.h> +#include <linux/platform_device.h> +#include <linux/fb.h> + +#include <video/w100fb.h> + +#include <asm/setup.h> +#include <asm/mach/arch.h> +#include <asm/mach-types.h> + +#include <mach/mfp-pxa25x.h> +#include <mach/hardware.h> +#include <mach/udc.h> + +#include "generic.h" +#include "eseries.h" + +/* ---------------------- E750 LCD definitions -------------------- */ + +static struct w100_gen_regs e750_lcd_regs = { + .lcd_format = 0x00008003, + .lcdd_cntl1 = 0x00000000, + .lcdd_cntl2 = 0x0003ffff, + .genlcd_cntl1 = 0x00fff003, + .genlcd_cntl2 = 0x003c0f03, + .genlcd_cntl3 = 0x000143aa, +}; + +static struct w100_mode e750_lcd_mode = { + .xres = 240, + .yres = 320, + .left_margin = 21, + .right_margin = 22, + .upper_margin = 5, + .lower_margin = 4, + .crtc_ss = 0x80150014, + .crtc_ls = 0x8014000d, + .crtc_gs = 0xc1000005, + .crtc_vpos_gs = 0x00020147, + .crtc_rev = 0x0040010a, + .crtc_dclk = 0xa1700030, + .crtc_gclk = 0x80cc0015, + .crtc_goe = 0x80cc0015, + .crtc_ps1_active = 0x61060017, + .pll_freq = 57, + .pixclk_divider = 4, + .pixclk_divider_rotated = 4, + .pixclk_src = CLK_SRC_XTAL, + .sysclk_divider = 1, + .sysclk_src = CLK_SRC_PLL, +}; + +static struct w100_gpio_regs e750_w100_gpio_info = { + .init_data1 = 0x01192f1b, + .gpio_dir1 = 0xd5ffdeff, + .gpio_oe1 = 0x000020bf, + .init_data2 = 0x010f010f, + .gpio_dir2 = 0xffffffff, + .gpio_oe2 = 0x000001cf, +}; + +static struct w100fb_mach_info e750_fb_info = { + .modelist = &e750_lcd_mode, + .num_modes = 1, + .regs = &e750_lcd_regs, + .gpio = &e750_w100_gpio_info, + .xtal_freq = 14318000, + .xtal_dbl = 1, +}; + +static struct resource e750_fb_resources[] = { + [0] = { + .start = 0x0c000000, + .end = 0x0cffffff, + .flags = IORESOURCE_MEM, + }, +}; + +static struct platform_device e750_fb_device = { + .name = "w100fb", + .id = -1, + .dev = { + .platform_data = &e750_fb_info, + }, + .num_resources = ARRAY_SIZE(e750_fb_resources), + .resource = e750_fb_resources, +}; + +/* ----------------------------------------------------------------------- */ + +static struct platform_device *devices[] __initdata = { + &e750_fb_device, +}; + +static void __init e750_init(void) +{ + platform_add_devices(devices, ARRAY_SIZE(devices)); + pxa_set_udc_info(&e7xx_udc_mach_info); +} + +MACHINE_START(E750, "Toshiba e750") + /* Maintainer: Ian Molton (spyro@f2s.com) */ + .phys_io = 0x40000000, + .io_pg_offst = (io_p2v(0x40000000) >> 18) & 0xfffc, + .boot_params = 0xa0000100, + .map_io = pxa_map_io, + .init_irq = pxa25x_init_irq, + .fixup = eseries_fixup, + .init_machine = e750_init, + .timer = &pxa_timer, +MACHINE_END + diff --git a/arch/arm/mach-pxa/e800.c b/arch/arm/mach-pxa/e800.c new file mode 100644 index 00000000000..a293e09bfe2 --- /dev/null +++ b/arch/arm/mach-pxa/e800.c @@ -0,0 +1,186 @@ +/* + * Hardware definitions for the Toshiba eseries PDAs + * + * Copyright (c) 2003 Ian Molton <spyro@f2s.com> + * + * This file is licensed under + * the terms of the GNU General Public License version 2. This program + * is licensed "as is" without any warranty of any kind, whether express + * or implied. + * + */ + +#include <linux/kernel.h> +#include <linux/init.h> +#include <linux/device.h> +#include <linux/platform_device.h> +#include <linux/fb.h> + +#include <video/w100fb.h> + +#include <asm/setup.h> +#include <asm/mach/arch.h> +#include <asm/mach-types.h> + +#include <mach/mfp-pxa25x.h> +#include <mach/hardware.h> +#include <mach/eseries-gpio.h> +#include <mach/udc.h> + +#include "generic.h" +#include "eseries.h" + +/* ------------------------ e800 LCD definitions ------------------------- */ + +static struct w100_gen_regs e800_lcd_regs = { + .lcd_format = 0x00008003, + .lcdd_cntl1 = 0x02a00000, + .lcdd_cntl2 = 0x0003ffff, + .genlcd_cntl1 = 0x000ff2a3, + .genlcd_cntl2 = 0x000002a3, + .genlcd_cntl3 = 0x000102aa, +}; + +static struct w100_mode e800_lcd_mode[2] = { + [0] = { + .xres = 480, + .yres = 640, + .left_margin = 52, + .right_margin = 148, + .upper_margin = 2, + .lower_margin = 6, + .crtc_ss = 0x80350034, + .crtc_ls = 0x802b0026, + .crtc_gs = 0x80160016, + .crtc_vpos_gs = 0x00020003, + .crtc_rev = 0x0040001d, + .crtc_dclk = 0xe0000000, + .crtc_gclk = 0x82a50049, + .crtc_goe = 0x80ee001c, + .crtc_ps1_active = 0x00000000, + .pll_freq = 128, + .pixclk_divider = 4, + .pixclk_divider_rotated = 6, + .pixclk_src = CLK_SRC_PLL, + .sysclk_divider = 0, + .sysclk_src = CLK_SRC_PLL, + }, + [1] = { + .xres = 240, + .yres = 320, + .left_margin = 15, + .right_margin = 88, + .upper_margin = 0, + .lower_margin = 7, + .crtc_ss = 0xd010000f, + .crtc_ls = 0x80070003, + .crtc_gs = 0x80000000, + .crtc_vpos_gs = 0x01460147, + .crtc_rev = 0x00400003, + .crtc_dclk = 0xa1700030, + .crtc_gclk = 0x814b0008, + .crtc_goe = 0x80cc0015, + .crtc_ps1_active = 0x00000000, + .pll_freq = 100, + .pixclk_divider = 6, /* Wince uses 14 which gives a */ + .pixclk_divider_rotated = 6, /* 7MHz Pclk. We use a 14MHz one */ + .pixclk_src = CLK_SRC_PLL, + .sysclk_divider = 0, + .sysclk_src = CLK_SRC_PLL, + } +}; + + +static struct w100_gpio_regs e800_w100_gpio_info = { + .init_data1 = 0xc13fc019, + .gpio_dir1 = 0x3e40df7f, + .gpio_oe1 = 0x003c3000, + .init_data2 = 0x00000000, + .gpio_dir2 = 0x00000000, + .gpio_oe2 = 0x00000000, +}; + +static struct w100_mem_info e800_w100_mem_info = { + .ext_cntl = 0x09640011, + .sdram_mode_reg = 0x00600021, + .ext_timing_cntl = 0x10001545, + .io_cntl = 0x7ddd7333, + .size = 0x1fffff, +}; + +static void e800_tg_change(struct w100fb_par *par) +{ + unsigned long tmp; + + tmp = w100fb_gpio_read(W100_GPIO_PORT_A); + if (par->mode->xres == 480) + tmp |= 0x100; + else + tmp &= ~0x100; + w100fb_gpio_write(W100_GPIO_PORT_A, tmp); +} + +static struct w100_tg_info e800_tg_info = { + .change = e800_tg_change, +}; + +static struct w100fb_mach_info e800_fb_info = { + .modelist = e800_lcd_mode, + .num_modes = 2, + .regs = &e800_lcd_regs, + .gpio = &e800_w100_gpio_info, + .mem = &e800_w100_mem_info, + .tg = &e800_tg_info, + .xtal_freq = 16000000, +}; + +static struct resource e800_fb_resources[] = { + [0] = { + .start = 0x0c000000, + .end = 0x0cffffff, + .flags = IORESOURCE_MEM, + }, +}; + +static struct platform_device e800_fb_device = { + .name = "w100fb", + .id = -1, + .dev = { + .platform_data = &e800_fb_info, + }, + .num_resources = ARRAY_SIZE(e800_fb_resources), + .resource = e800_fb_resources, +}; + +/* --------------------------- UDC definitions --------------------------- */ + +static struct pxa2xx_udc_mach_info e800_udc_mach_info = { + .gpio_vbus = GPIO_E800_USB_DISC, + .gpio_pullup = GPIO_E800_USB_PULLUP, + .gpio_pullup_inverted = 1 +}; + +/* ----------------------------------------------------------------------- */ + +static struct platform_device *devices[] __initdata = { + &e800_fb_device, +}; + +static void __init e800_init(void) +{ + platform_add_devices(devices, ARRAY_SIZE(devices)); + pxa_set_udc_info(&e800_udc_mach_info); +} + +MACHINE_START(E800, "Toshiba e800") + /* Maintainer: Ian Molton (spyro@f2s.com) */ + .phys_io = 0x40000000, + .io_pg_offst = (io_p2v(0x40000000) >> 18) & 0xfffc, + .boot_params = 0xa0000100, + .map_io = pxa_map_io, + .init_irq = pxa25x_init_irq, + .fixup = eseries_fixup, + .init_machine = e800_init, + .timer = &pxa_timer, +MACHINE_END + diff --git a/arch/arm/mach-pxa/em-x270.c b/arch/arm/mach-pxa/em-x270.c index 9c57700ee5c..f5ed8038ede 100644 --- a/arch/arm/mach-pxa/em-x270.c +++ b/arch/arm/mach-pxa/em-x270.c @@ -1,7 +1,7 @@ /* - * Support for CompuLab EM-x270 platform + * Support for CompuLab EM-X270 platform * - * Copyright (C) 2007 CompuLab, Ltd. + * Copyright (C) 2007, 2008 CompuLab, Ltd. * Author: Mike Rapoport <mike@compulab.co.il> * * This program is free software; you can redistribute it and/or modify @@ -14,29 +14,159 @@ #include <linux/dm9000.h> #include <linux/rtc-v3020.h> - #include <linux/mtd/nand.h> #include <linux/mtd/partitions.h> +#include <linux/input.h> +#include <linux/gpio_keys.h> +#include <linux/gpio.h> #include <asm/mach-types.h> - #include <asm/mach/arch.h> -#include <asm/arch/pxa-regs.h> -#include <asm/arch/pxa2xx-gpio.h> -#include <asm/arch/pxafb.h> -#include <asm/arch/ohci.h> -#include <asm/arch/mmc.h> -#include <asm/arch/bitfield.h> +#include <mach/mfp-pxa27x.h> +#include <mach/pxa-regs.h> +#include <mach/pxa27x-udc.h> +#include <mach/audio.h> +#include <mach/pxafb.h> +#include <mach/ohci.h> +#include <mach/mmc.h> +#include <mach/pxa27x_keypad.h> #include "generic.h" /* GPIO IRQ usage */ -#define EM_X270_MMC_PD (105) -#define EM_X270_ETHIRQ IRQ_GPIO(41) -#define EM_X270_MMC_IRQ IRQ_GPIO(13) +#define GPIO41_ETHIRQ (41) +#define GPIO13_MMC_CD (13) +#define EM_X270_ETHIRQ IRQ_GPIO(GPIO41_ETHIRQ) +#define EM_X270_MMC_CD IRQ_GPIO(GPIO13_MMC_CD) + +/* NAND control GPIOs */ +#define GPIO11_NAND_CS (11) +#define GPIO56_NAND_RB (56) + +static unsigned long em_x270_pin_config[] = { + /* AC'97 */ + GPIO28_AC97_BITCLK, + GPIO29_AC97_SDATA_IN_0, + GPIO30_AC97_SDATA_OUT, + GPIO31_AC97_SYNC, + GPIO98_AC97_SYSCLK, + GPIO113_AC97_nRESET, + + /* BTUART */ + GPIO42_BTUART_RXD, + GPIO43_BTUART_TXD, + GPIO44_BTUART_CTS, + GPIO45_BTUART_RTS, + + /* STUART */ + GPIO46_STUART_RXD, + GPIO47_STUART_TXD, + + /* MCI controller */ + GPIO32_MMC_CLK, + GPIO112_MMC_CMD, + GPIO92_MMC_DAT_0, + GPIO109_MMC_DAT_1, + GPIO110_MMC_DAT_2, + GPIO111_MMC_DAT_3, + + /* LCD */ + GPIO58_LCD_LDD_0, + GPIO59_LCD_LDD_1, + GPIO60_LCD_LDD_2, + GPIO61_LCD_LDD_3, + GPIO62_LCD_LDD_4, + GPIO63_LCD_LDD_5, + GPIO64_LCD_LDD_6, + GPIO65_LCD_LDD_7, + GPIO66_LCD_LDD_8, + GPIO67_LCD_LDD_9, + GPIO68_LCD_LDD_10, + GPIO69_LCD_LDD_11, + GPIO70_LCD_LDD_12, + GPIO71_LCD_LDD_13, + GPIO72_LCD_LDD_14, + GPIO73_LCD_LDD_15, + GPIO74_LCD_FCLK, + GPIO75_LCD_LCLK, + GPIO76_LCD_PCLK, + GPIO77_LCD_BIAS, + + /* QCI */ + GPIO84_CIF_FV, + GPIO25_CIF_LV, + GPIO53_CIF_MCLK, + GPIO54_CIF_PCLK, + GPIO81_CIF_DD_0, + GPIO55_CIF_DD_1, + GPIO51_CIF_DD_2, + GPIO50_CIF_DD_3, + GPIO52_CIF_DD_4, + GPIO48_CIF_DD_5, + GPIO17_CIF_DD_6, + GPIO12_CIF_DD_7, + + /* I2C */ + GPIO117_I2C_SCL, + GPIO118_I2C_SDA, + + /* Keypad */ + GPIO100_KP_MKIN_0 | WAKEUP_ON_LEVEL_HIGH, + GPIO101_KP_MKIN_1 | WAKEUP_ON_LEVEL_HIGH, + GPIO102_KP_MKIN_2 | WAKEUP_ON_LEVEL_HIGH, + GPIO34_KP_MKIN_3 | WAKEUP_ON_LEVEL_HIGH, + GPIO39_KP_MKIN_4 | WAKEUP_ON_LEVEL_HIGH, + GPIO99_KP_MKIN_5 | WAKEUP_ON_LEVEL_HIGH, + GPIO91_KP_MKIN_6 | WAKEUP_ON_LEVEL_HIGH, + GPIO36_KP_MKIN_7 | WAKEUP_ON_LEVEL_HIGH, + GPIO103_KP_MKOUT_0, + GPIO104_KP_MKOUT_1, + GPIO105_KP_MKOUT_2, + GPIO106_KP_MKOUT_3, + GPIO107_KP_MKOUT_4, + GPIO108_KP_MKOUT_5, + GPIO96_KP_MKOUT_6, + GPIO22_KP_MKOUT_7, + + /* SSP1 */ + GPIO26_SSP1_RXD, + GPIO23_SSP1_SCLK, + GPIO24_SSP1_SFRM, + GPIO57_SSP1_TXD, + + /* SSP2 */ + GPIO19_SSP2_SCLK, + GPIO14_SSP2_SFRM, + GPIO89_SSP2_TXD, + GPIO88_SSP2_RXD, + + /* SDRAM and local bus */ + GPIO15_nCS_1, + GPIO78_nCS_2, + GPIO79_nCS_3, + GPIO80_nCS_4, + GPIO49_nPWE, + GPIO18_RDY, + + /* GPIO */ + GPIO1_GPIO | WAKEUP_ON_EDGE_BOTH, + + /* power controls */ + GPIO20_GPIO | MFP_LPM_DRIVE_LOW, /* GPRS_PWEN */ + GPIO115_GPIO | MFP_LPM_DRIVE_LOW, /* WLAN_PWEN */ + + /* NAND controls */ + GPIO11_GPIO | MFP_LPM_DRIVE_HIGH, /* NAND CE# */ + GPIO56_GPIO, /* NAND Ready/Busy */ + + /* interrupts */ + GPIO13_GPIO, /* MMC card detect */ + GPIO41_GPIO, /* DM9000 interrupt */ +}; -static struct resource em_x270_dm9k_resource[] = { +#if defined(CONFIG_DM9000) || defined(CONFIG_DM9000_MODULE) +static struct resource em_x270_dm9000_resource[] = { [0] = { .start = PXA_CS2_PHYS, .end = PXA_CS2_PHYS + 3, @@ -54,38 +184,30 @@ static struct resource em_x270_dm9k_resource[] = { } }; -/* for the moment we limit ourselves to 32bit IO until some - * better IO routines can be written and tested - */ -static struct dm9000_plat_data em_x270_dm9k_platdata = { +static struct dm9000_plat_data em_x270_dm9000_platdata = { .flags = DM9000_PLATF_32BITONLY, }; -/* Ethernet device */ -static struct platform_device em_x270_dm9k = { +static struct platform_device em_x270_dm9000 = { .name = "dm9000", .id = 0, - .num_resources = ARRAY_SIZE(em_x270_dm9k_resource), - .resource = em_x270_dm9k_resource, + .num_resources = ARRAY_SIZE(em_x270_dm9000_resource), + .resource = em_x270_dm9000_resource, .dev = { - .platform_data = &em_x270_dm9k_platdata, + .platform_data = &em_x270_dm9000_platdata, } }; -/* audio device */ -static struct platform_device em_x270_audio = { - .name = "pxa2xx-ac97", - .id = -1, -}; - -/* WM9712 touchscreen controller. Hopefully the driver will make it to - * the mainstream sometime */ -static struct platform_device em_x270_ts = { - .name = "wm97xx-ts", - .id = -1, -}; +static void __init em_x270_init_dm9000(void) +{ + platform_device_register(&em_x270_dm9000); +} +#else +static inline void em_x270_init_dm9000(void) {} +#endif -/* RTC */ +/* V3020 RTC */ +#if defined(CONFIG_RTC_DRV_V3020) || defined(CONFIG_RTC_DRV_V3020_MODULE) static struct resource em_x270_v3020_resource[] = { [0] = { .start = PXA_CS4_PHYS, @@ -108,20 +230,26 @@ static struct platform_device em_x270_rtc = { } }; -/* NAND flash */ -#define GPIO_NAND_CS (11) -#define GPIO_NAND_RB (56) +static void __init em_x270_init_rtc(void) +{ + platform_device_register(&em_x270_rtc); +} +#else +static inline void em_x270_init_rtc(void) {} +#endif +/* NAND flash */ +#if defined(CONFIG_MTD_NAND_PLATFORM) || defined(CONFIG_MTD_NAND_PLATFORM_MODULE) static inline void nand_cs_on(void) { - GPCR(GPIO_NAND_CS) = GPIO_bit(GPIO_NAND_CS); + gpio_set_value(GPIO11_NAND_CS, 0); } static void nand_cs_off(void) { dsb(); - GPSR(GPIO_NAND_CS) = GPIO_bit(GPIO_NAND_CS); + gpio_set_value(GPIO11_NAND_CS, 1); } /* hardware specific access to control-lines */ @@ -161,7 +289,7 @@ static int em_x270_nand_device_ready(struct mtd_info *mtd) { dsb(); - return GPLR(GPIO_NAND_RB) & GPIO_bit(GPIO_NAND_RB); + return gpio_get_value(GPIO56_NAND_RB); } static struct mtd_partition em_x270_partition_info[] = { @@ -214,23 +342,37 @@ static struct platform_device em_x270_nand = { } }; -/* platform devices */ -static struct platform_device *platform_devices[] __initdata = { - &em_x270_dm9k, - &em_x270_audio, - &em_x270_ts, - &em_x270_rtc, - &em_x270_nand, -}; +static void __init em_x270_init_nand(void) +{ + int err; + + err = gpio_request(GPIO11_NAND_CS, "NAND CS"); + if (err) { + pr_warning("EM-X270: failed to request NAND CS gpio\n"); + return; + } + + gpio_direction_output(GPIO11_NAND_CS, 1); + + err = gpio_request(GPIO56_NAND_RB, "NAND R/B"); + if (err) { + pr_warning("EM-X270: failed to request NAND R/B gpio\n"); + gpio_free(GPIO11_NAND_CS); + return; + } + gpio_direction_input(GPIO56_NAND_RB); + + platform_device_register(&em_x270_nand); +} +#else +static inline void em_x270_init_nand(void) {} +#endif /* PXA27x OHCI controller setup */ +#if defined(CONFIG_USB_OHCI_HCD) || defined(CONFIG_USB_OHCI_HCD_MODULE) static int em_x270_ohci_init(struct device *dev) { - /* Set the Power Control Polarity Low */ - UHCHR = (UHCHR | UHCHR_PCPL) & - ~(UHCHR_SSEP1 | UHCHR_SSEP2 | UHCHR_SSE); - /* enable port 2 transiever */ UP2OCR = UP2OCR_HXS | UP2OCR_HXOE; @@ -239,30 +381,27 @@ static int em_x270_ohci_init(struct device *dev) static struct pxaohci_platform_data em_x270_ohci_platform_data = { .port_mode = PMM_PERPORT_MODE, + .flags = ENABLE_PORT1 | ENABLE_PORT2 | POWER_CONTROL_LOW, .init = em_x270_ohci_init, }; +static void __init em_x270_init_ohci(void) +{ + pxa_set_ohci_info(&em_x270_ohci_platform_data); +} +#else +static inline void em_x270_init_ohci(void) {} +#endif +/* MCI controller setup */ +#if defined(CONFIG_MMC) || defined(CONFIG_MMC_MODULE) static int em_x270_mci_init(struct device *dev, irq_handler_t em_x270_detect_int, void *data) { - int err; - - /* setup GPIO for PXA27x MMC controller */ - pxa_gpio_mode(GPIO32_MMCCLK_MD); - pxa_gpio_mode(GPIO112_MMCCMD_MD); - pxa_gpio_mode(GPIO92_MMCDAT0_MD); - pxa_gpio_mode(GPIO109_MMCDAT1_MD); - pxa_gpio_mode(GPIO110_MMCDAT2_MD); - pxa_gpio_mode(GPIO111_MMCDAT3_MD); - - /* EM-X270 uses GPIO13 as SD power enable */ - pxa_gpio_mode(EM_X270_MMC_PD | GPIO_OUT); - - err = request_irq(EM_X270_MMC_IRQ, em_x270_detect_int, - IRQF_DISABLED | IRQF_TRIGGER_FALLING, - "MMC card detect", data); + int err = request_irq(EM_X270_MMC_CD, em_x270_detect_int, + IRQF_DISABLED | IRQF_TRIGGER_FALLING, + "MMC card detect", data); if (err) { printk(KERN_ERR "%s: can't request MMC card detect IRQ: %d\n", __func__, err); @@ -284,7 +423,8 @@ static void em_x270_mci_setpower(struct device *dev, unsigned int vdd) static void em_x270_mci_exit(struct device *dev, void *data) { - free_irq(EM_X270_MMC_IRQ, data); + int irq = gpio_to_irq(GPIO13_MMC_CD); + free_irq(irq, data); } static struct pxamci_platform_data em_x270_mci_platform_data = { @@ -294,7 +434,16 @@ static struct pxamci_platform_data em_x270_mci_platform_data = { .exit = em_x270_mci_exit, }; +static void __init em_x270_init_mmc(void) +{ + pxa_set_mci_info(&em_x270_mci_platform_data); +} +#else +static inline void em_x270_init_mmc(void) {} +#endif + /* LCD 480x640 */ +#if defined(CONFIG_FB_PXA) || defined(CONFIG_FB_PXA_MODULE) static struct pxafb_mode_info em_x270_lcd_mode = { .pixclock = 50000, .bpp = 16, @@ -312,39 +461,96 @@ static struct pxafb_mode_info em_x270_lcd_mode = { static struct pxafb_mach_info em_x270_lcd = { .modes = &em_x270_lcd_mode, .num_modes = 1, - .cmap_inverse = 0, - .cmap_static = 0, - .lccr0 = LCCR0_PAS, - .lccr3 = LCCR3_PixClkDiv(0x01) | LCCR3_Acb(0xff), + .lcd_conn = LCD_COLOR_TFT_16BPP, }; - -static void __init em_x270_init(void) +static void __init em_x270_init_lcd(void) { - /* setup LCD */ set_pxa_fb_info(&em_x270_lcd); +} +#else +static inline void em_x270_init_lcd(void) {} +#endif + +#if defined(CONFIG_SND_PXA2XX_AC97) || defined(CONFIG_SND_PXA2XX_AC97_MODULE) +static void __init em_x270_init_ac97(void) +{ + pxa_set_ac97_info(NULL); +} +#else +static inline void em_x270_init_ac97(void) {} +#endif + +#if defined(CONFIG_KEYBOARD_PXA27x) || defined(CONFIG_KEYBOARD_PXA27x_MODULE) +static unsigned int em_x270_matrix_keys[] = { + KEY(0, 0, KEY_A), KEY(1, 0, KEY_UP), KEY(2, 1, KEY_B), + KEY(0, 2, KEY_LEFT), KEY(1, 1, KEY_ENTER), KEY(2, 0, KEY_RIGHT), + KEY(0, 1, KEY_C), KEY(1, 2, KEY_DOWN), KEY(2, 2, KEY_D), +}; - /* register EM-X270 platform devices */ - platform_add_devices(platform_devices, ARRAY_SIZE(platform_devices)); +struct pxa27x_keypad_platform_data em_x270_keypad_info = { + /* code map for the matrix keys */ + .matrix_key_rows = 3, + .matrix_key_cols = 3, + .matrix_key_map = em_x270_matrix_keys, + .matrix_key_map_size = ARRAY_SIZE(em_x270_matrix_keys), +}; - /* set MCI and OHCI platform parameters */ - pxa_set_mci_info(&em_x270_mci_platform_data); - pxa_set_ohci_info(&em_x270_ohci_platform_data); +static void __init em_x270_init_keypad(void) +{ + pxa_set_keypad_info(&em_x270_keypad_info); +} +#else +static inline void em_x270_init_keypad(void) {} +#endif + +#if defined(CONFIG_KEYBOARD_GPIO) || defined(CONFIG_KEYBOARD_GPIO_MODULE) +static struct gpio_keys_button gpio_keys_button[] = { + [0] = { + .desc = "sleep/wakeup", + .code = KEY_SUSPEND, + .type = EV_PWR, + .gpio = 1, + .wakeup = 1, + }, +}; + +static struct gpio_keys_platform_data em_x270_gpio_keys_data = { + .buttons = gpio_keys_button, + .nbuttons = 1, +}; - /* setup STUART GPIOs */ - pxa_gpio_mode(GPIO46_STRXD_MD); - pxa_gpio_mode(GPIO47_STTXD_MD); +static struct platform_device em_x270_gpio_keys = { + .name = "gpio-keys", + .id = -1, + .dev = { + .platform_data = &em_x270_gpio_keys_data, + }, +}; - /* setup BTUART GPIOs */ - pxa_gpio_mode(GPIO42_BTRXD_MD); - pxa_gpio_mode(GPIO43_BTTXD_MD); - pxa_gpio_mode(GPIO44_BTCTS_MD); - pxa_gpio_mode(GPIO45_BTRTS_MD); +static void __init em_x270_init_gpio_keys(void) +{ + platform_device_register(&em_x270_gpio_keys); +} +#else +static inline void em_x270_init_gpio_keys(void) {} +#endif - /* Setup interrupt for dm9000 */ - set_irq_type(EM_X270_ETHIRQ, IRQT_RISING); +static void __init em_x270_init(void) +{ + pxa2xx_mfp_config(ARRAY_AND_SIZE(em_x270_pin_config)); + + em_x270_init_dm9000(); + em_x270_init_rtc(); + em_x270_init_nand(); + em_x270_init_lcd(); + em_x270_init_mmc(); + em_x270_init_ohci(); + em_x270_init_keypad(); + em_x270_init_gpio_keys(); + em_x270_init_ac97(); } -MACHINE_START(EM_X270, "Compulab EM-x270") +MACHINE_START(EM_X270, "Compulab EM-X270") .boot_params = 0xa0000100, .phys_io = 0x40000000, .io_pg_offst = (io_p2v(0x40000000) >> 18) & 0xfffc, diff --git a/arch/arm/mach-pxa/eseries.c b/arch/arm/mach-pxa/eseries.c index ee0ae93c876..d28849b50a1 100644 --- a/arch/arm/mach-pxa/eseries.c +++ b/arch/arm/mach-pxa/eseries.c @@ -10,18 +10,23 @@ * */ +#include <linux/kernel.h> #include <linux/init.h> #include <asm/setup.h> #include <asm/mach/arch.h> -#include <asm/arch/hardware.h> #include <asm/mach-types.h> -#include <generic.h> +#include <mach/mfp-pxa25x.h> +#include <mach/hardware.h> +#include <mach/eseries-gpio.h> +#include <mach/udc.h> + +#include "generic.h" /* Only e800 has 128MB RAM */ -static void __init eseries_fixup(struct machine_desc *desc, - struct tag *tags, char **cmdline, struct meminfo *mi) +void __init eseries_fixup(struct machine_desc *desc, + struct tag *tags, char **cmdline, struct meminfo *mi) { mi->nr_banks=1; mi->bank[0].start = 0xa0000000; @@ -32,70 +37,9 @@ static void __init eseries_fixup(struct machine_desc *desc, mi->bank[0].size = (64*1024*1024); } -/* e-series machine definitions */ - -#ifdef CONFIG_MACH_E330 -MACHINE_START(E330, "Toshiba e330") - /* Maintainer: Ian Molton (spyro@f2s.com) */ - .phys_io = 0x40000000, - .io_pg_offst = (io_p2v(0x40000000) >> 18) & 0xfffc, - .boot_params = 0xa0000100, - .map_io = pxa_map_io, - .init_irq = pxa25x_init_irq, - .fixup = eseries_fixup, - .timer = &pxa_timer, -MACHINE_END -#endif - -#ifdef CONFIG_MACH_E740 -MACHINE_START(E740, "Toshiba e740") - /* Maintainer: Ian Molton (spyro@f2s.com) */ - .phys_io = 0x40000000, - .io_pg_offst = (io_p2v(0x40000000) >> 18) & 0xfffc, - .boot_params = 0xa0000100, - .map_io = pxa_map_io, - .init_irq = pxa25x_init_irq, - .fixup = eseries_fixup, - .timer = &pxa_timer, -MACHINE_END -#endif - -#ifdef CONFIG_MACH_E750 -MACHINE_START(E750, "Toshiba e750") - /* Maintainer: Ian Molton (spyro@f2s.com) */ - .phys_io = 0x40000000, - .io_pg_offst = (io_p2v(0x40000000) >> 18) & 0xfffc, - .boot_params = 0xa0000100, - .map_io = pxa_map_io, - .init_irq = pxa25x_init_irq, - .fixup = eseries_fixup, - .timer = &pxa_timer, -MACHINE_END -#endif - -#ifdef CONFIG_MACH_E400 -MACHINE_START(E400, "Toshiba e400") - /* Maintainer: Ian Molton (spyro@f2s.com) */ - .phys_io = 0x40000000, - .io_pg_offst = (io_p2v(0x40000000) >> 18) & 0xfffc, - .boot_params = 0xa0000100, - .map_io = pxa_map_io, - .init_irq = pxa25x_init_irq, - .fixup = eseries_fixup, - .timer = &pxa_timer, -MACHINE_END -#endif - -#ifdef CONFIG_MACH_E800 -MACHINE_START(E800, "Toshiba e800") - /* Maintainer: Ian Molton (spyro@f2s.com) */ - .phys_io = 0x40000000, - .io_pg_offst = (io_p2v(0x40000000) >> 18) & 0xfffc, - .boot_params = 0xa0000100, - .map_io = pxa_map_io, - .init_irq = pxa25x_init_irq, - .fixup = eseries_fixup, - .timer = &pxa_timer, -MACHINE_END -#endif +struct pxa2xx_udc_mach_info e7xx_udc_mach_info = { + .gpio_vbus = GPIO_E7XX_USB_DISC, + .gpio_pullup = GPIO_E7XX_USB_PULLUP, + .gpio_pullup_inverted = 1 +}; diff --git a/arch/arm/mach-pxa/eseries.h b/arch/arm/mach-pxa/eseries.h new file mode 100644 index 00000000000..a83f88d4b6a --- /dev/null +++ b/arch/arm/mach-pxa/eseries.h @@ -0,0 +1,4 @@ +void __init eseries_fixup(struct machine_desc *desc, + struct tag *tags, char **cmdline, struct meminfo *mi); + +extern struct pxa2xx_udc_mach_info e7xx_udc_mach_info; diff --git a/arch/arm/mach-pxa/ezx.c b/arch/arm/mach-pxa/ezx.c new file mode 100644 index 00000000000..cc3d850cc0b --- /dev/null +++ b/arch/arm/mach-pxa/ezx.c @@ -0,0 +1,220 @@ +/* + * ezx.c - Common code for the EZX platform. + * + * Copyright (C) 2005-2006 Harald Welte <laforge@openezx.org>, + * 2007-2008 Daniel Ribeiro <drwyrm@gmail.com>, + * 2007-2008 Stefan Schmidt <stefan@datenfreihafen.org> + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + * + */ + +#include <linux/kernel.h> +#include <linux/init.h> +#include <linux/platform_device.h> +#include <linux/delay.h> +#include <linux/pwm_backlight.h> + +#include <asm/setup.h> +#include <mach/pxafb.h> +#include <mach/ohci.h> +#include <mach/i2c.h> + +#include <mach/mfp-pxa27x.h> +#include <mach/pxa-regs.h> +#include <mach/pxa2xx-regs.h> +#include <asm/mach-types.h> +#include <asm/mach/arch.h> + +#include "devices.h" +#include "generic.h" + +static struct platform_pwm_backlight_data ezx_backlight_data = { + .pwm_id = 0, + .max_brightness = 1023, + .dft_brightness = 1023, + .pwm_period_ns = 78770, +}; + +static struct platform_device ezx_backlight_device = { + .name = "pwm-backlight", + .dev = { + .parent = &pxa27x_device_pwm0.dev, + .platform_data = &ezx_backlight_data, + }, +}; + +static struct pxafb_mode_info mode_ezx_old = { + .pixclock = 150000, + .xres = 240, + .yres = 320, + .bpp = 16, + .hsync_len = 10, + .left_margin = 20, + .right_margin = 10, + .vsync_len = 2, + .upper_margin = 3, + .lower_margin = 2, + .sync = 0, +}; + +static struct pxafb_mach_info ezx_fb_info_1 = { + .modes = &mode_ezx_old, + .num_modes = 1, + .lcd_conn = LCD_COLOR_TFT_16BPP, +}; + +static struct pxafb_mode_info mode_72r89803y01 = { + .pixclock = 192308, + .xres = 240, + .yres = 320, + .bpp = 32, + .depth = 18, + .hsync_len = 10, + .left_margin = 20, + .right_margin = 10, + .vsync_len = 2, + .upper_margin = 3, + .lower_margin = 2, + .sync = 0, +}; + +static struct pxafb_mach_info ezx_fb_info_2 = { + .modes = &mode_72r89803y01, + .num_modes = 1, + .lcd_conn = LCD_COLOR_TFT_18BPP, +}; + +static struct platform_device *devices[] __initdata = { + &ezx_backlight_device, +}; + +static unsigned long ezx_pin_config[] __initdata = { + /* PWM backlight */ + GPIO16_PWM0_OUT, + + /* BTUART */ + GPIO42_BTUART_RXD, + GPIO43_BTUART_TXD, + GPIO44_BTUART_CTS, + GPIO45_BTUART_RTS, + + /* STUART */ + GPIO46_STUART_RXD, + GPIO47_STUART_TXD, + + /* For A780 support (connected with Neptune GSM chip) */ + GPIO30_USB_P3_2, /* ICL_TXENB */ + GPIO31_USB_P3_6, /* ICL_VPOUT */ + GPIO90_USB_P3_5, /* ICL_VPIN */ + GPIO91_USB_P3_1, /* ICL_XRXD */ + GPIO56_USB_P3_4, /* ICL_VMOUT */ + GPIO113_USB_P3_3, /* /ICL_VMIN */ +}; + +static void __init ezx_init(void) +{ + pxa2xx_mfp_config(ARRAY_AND_SIZE(ezx_pin_config)); + pxa_set_i2c_info(NULL); + if (machine_is_ezx_a780() || machine_is_ezx_e680()) + set_pxa_fb_info(&ezx_fb_info_1); + else + set_pxa_fb_info(&ezx_fb_info_2); + + platform_add_devices(devices, ARRAY_SIZE(devices)); +} + +static void __init ezx_fixup(struct machine_desc *desc, struct tag *tags, + char **cmdline, struct meminfo *mi) +{ + /* We have two ram chips. First one with 32MB at 0xA0000000 and a second + * 16MB one at 0xAC000000 + */ + mi->nr_banks = 2; + mi->bank[0].start = 0xa0000000; + mi->bank[0].node = 0; + mi->bank[0].size = (32*1024*1024); + mi->bank[1].start = 0xac000000; + mi->bank[1].node = 1; + mi->bank[1].size = (16*1024*1024); +} + +#ifdef CONFIG_MACH_EZX_A780 +MACHINE_START(EZX_A780, "Motorola EZX A780") + .phys_io = 0x40000000, + .io_pg_offst = (io_p2v(0x40000000) >> 18) & 0xfffc, + .fixup = ezx_fixup, + .boot_params = 0xa0000100, + .map_io = pxa_map_io, + .init_irq = pxa27x_init_irq, + .timer = &pxa_timer, + .init_machine = &ezx_init, +MACHINE_END +#endif + +#ifdef CONFIG_MACH_EZX_E680 +MACHINE_START(EZX_E680, "Motorola EZX E680") + .phys_io = 0x40000000, + .io_pg_offst = (io_p2v(0x40000000) >> 18) & 0xfffc, + .fixup = ezx_fixup, + .boot_params = 0xa0000100, + .map_io = pxa_map_io, + .init_irq = pxa27x_init_irq, + .timer = &pxa_timer, + .init_machine = &ezx_init, +MACHINE_END +#endif + +#ifdef CONFIG_MACH_EZX_A1200 +MACHINE_START(EZX_A1200, "Motorola EZX A1200") + .phys_io = 0x40000000, + .io_pg_offst = (io_p2v(0x40000000) >> 18) & 0xfffc, + .fixup = ezx_fixup, + .boot_params = 0xa0000100, + .map_io = pxa_map_io, + .init_irq = pxa27x_init_irq, + .timer = &pxa_timer, + .init_machine = &ezx_init, +MACHINE_END +#endif + +#ifdef CONFIG_MACH_EZX_A910 +MACHINE_START(EZX_A910, "Motorola EZX A910") + .phys_io = 0x40000000, + .io_pg_offst = (io_p2v(0x40000000) >> 18) & 0xfffc, + .fixup = ezx_fixup, + .boot_params = 0xa0000100, + .map_io = pxa_map_io, + .init_irq = pxa27x_init_irq, + .timer = &pxa_timer, + .init_machine = &ezx_init, +MACHINE_END +#endif + +#ifdef CONFIG_MACH_EZX_E6 +MACHINE_START(EZX_E6, "Motorola EZX E6") + .phys_io = 0x40000000, + .io_pg_offst = (io_p2v(0x40000000) >> 18) & 0xfffc, + .fixup = ezx_fixup, + .boot_params = 0xa0000100, + .map_io = pxa_map_io, + .init_irq = pxa27x_init_irq, + .timer = &pxa_timer, + .init_machine = &ezx_init, +MACHINE_END +#endif + +#ifdef CONFIG_MACH_EZX_E2 +MACHINE_START(EZX_E2, "Motorola EZX E2") + .phys_io = 0x40000000, + .io_pg_offst = (io_p2v(0x40000000) >> 18) & 0xfffc, + .fixup = ezx_fixup, + .boot_params = 0xa0000100, + .map_io = pxa_map_io, + .init_irq = pxa27x_init_irq, + .timer = &pxa_timer, + .init_machine = &ezx_init, +MACHINE_END +#endif diff --git a/arch/arm/mach-pxa/generic.c b/arch/arm/mach-pxa/generic.c index 44617938f3f..85ed0b33331 100644 --- a/arch/arm/mach-pxa/generic.c +++ b/arch/arm/mach-pxa/generic.c @@ -20,15 +20,25 @@ #include <linux/kernel.h> #include <linux/init.h> -#include <asm/hardware.h> +#include <mach/hardware.h> #include <asm/system.h> #include <asm/pgtable.h> #include <asm/mach/map.h> -#include <asm/arch/pxa-regs.h> +#include <mach/pxa-regs.h> +#include <mach/reset.h> #include "generic.h" +void clear_reset_status(unsigned int mask) +{ + if (cpu_is_pxa2xx()) + pxa2xx_clear_reset_status(mask); + + if (cpu_is_pxa3xx()) + pxa3xx_clear_reset_status(mask); +} + /* * Get the clock frequency as reflected by CCCR and the turbo flag. * We assume these values have been applied via a fcs. @@ -36,7 +46,7 @@ */ unsigned int get_clk_frequency_khz(int info) { - if (cpu_is_pxa21x() || cpu_is_pxa25x()) + if (cpu_is_pxa25x()) return pxa25x_get_clk_frequency_khz(info); else if (cpu_is_pxa27x()) return pxa27x_get_clk_frequency_khz(info); @@ -50,7 +60,7 @@ EXPORT_SYMBOL(get_clk_frequency_khz); */ unsigned int get_memclk_frequency_10khz(void) { - if (cpu_is_pxa21x() || cpu_is_pxa25x()) + if (cpu_is_pxa25x()) return pxa25x_get_memclk_frequency_10khz(); else if (cpu_is_pxa27x()) return pxa27x_get_memclk_frequency_10khz(); @@ -60,23 +70,6 @@ unsigned int get_memclk_frequency_10khz(void) EXPORT_SYMBOL(get_memclk_frequency_10khz); /* - * Routine to safely enable or disable a clock in the CKEN - */ -void __pxa_set_cken(int clock, int enable) -{ - unsigned long flags; - local_irq_save(flags); - - if (enable) - CKEN |= (1 << clock); - else - CKEN &= ~(1 << clock); - - local_irq_restore(flags); -} -EXPORT_SYMBOL(__pxa_set_cken); - -/* * Intel PXA2xx internal register mapping. * * Note 1: not all PXA2xx variants implement all those addresses. @@ -95,11 +88,6 @@ static struct map_desc standard_io_desc[] __initdata = { .pfn = __phys_to_pfn(0x48000000), .length = 0x00200000, .type = MT_DEVICE - }, { /* USB host */ - .virtual = 0xf8000000, - .pfn = __phys_to_pfn(0x4c000000), - .length = 0x00100000, - .type = MT_DEVICE }, { /* Camera */ .virtual = 0xfa000000, .pfn = __phys_to_pfn(0x50000000), diff --git a/arch/arm/mach-pxa/generic.h b/arch/arm/mach-pxa/generic.h index 5bb7ae75783..dc876a8e666 100644 --- a/arch/arm/mach-pxa/generic.h +++ b/arch/arm/mach-pxa/generic.h @@ -47,14 +47,23 @@ extern unsigned pxa27x_get_memclk_frequency_10khz(void); #define pxa27x_get_memclk_frequency_10khz() (0) #endif +#if defined(CONFIG_PXA25x) || defined(CONFIG_PXA27x) +extern void pxa2xx_clear_reset_status(unsigned int); +#else +static inline void pxa2xx_clear_reset_status(unsigned int mask) {} +#endif + #ifdef CONFIG_PXA3xx extern unsigned pxa3xx_get_clk_frequency_khz(int); extern unsigned pxa3xx_get_memclk_frequency_10khz(void); +extern void pxa3xx_clear_reset_status(unsigned int); #else #define pxa3xx_get_clk_frequency_khz(x) (0) #define pxa3xx_get_memclk_frequency_10khz() (0) +static inline void pxa3xx_clear_reset_status(unsigned int mask) {} #endif extern struct sysdev_class pxa_irq_sysclass; extern struct sysdev_class pxa_gpio_sysclass; +extern struct sysdev_class pxa2xx_mfp_sysclass; extern struct sysdev_class pxa3xx_mfp_sysclass; diff --git a/arch/arm/mach-pxa/gpio.c b/arch/arm/mach-pxa/gpio.c index 7d3e16970be..14930cf8be7 100644 --- a/arch/arm/mach-pxa/gpio.c +++ b/arch/arm/mach-pxa/gpio.c @@ -16,12 +16,12 @@ #include <linux/module.h> #include <linux/irq.h> #include <linux/sysdev.h> +#include <linux/io.h> #include <asm/gpio.h> -#include <asm/hardware.h> -#include <asm/io.h> -#include <asm/arch/pxa-regs.h> -#include <asm/arch/pxa2xx-gpio.h> +#include <mach/hardware.h> +#include <mach/pxa-regs.h> +#include <mach/pxa2xx-gpio.h> #include "generic.h" @@ -275,7 +275,7 @@ static void pxa_gpio_demux_handler(unsigned int irq, struct irq_desc *desc) loop = 1; n = PXA_GPIO_IRQ_BASE + bit; - desc_handle_irq(n, irq_desc + n); + generic_handle_irq(n); bit = find_next_bit(gedr, GEDR_BITS, bit + 1); } diff --git a/arch/arm/mach-pxa/gumstix.c b/arch/arm/mach-pxa/gumstix.c index bdf23975403..d8962a0fb98 100644 --- a/arch/arm/mach-pxa/gumstix.c +++ b/arch/arm/mach-pxa/gumstix.c @@ -20,13 +20,17 @@ #include <linux/init.h> #include <linux/platform_device.h> #include <linux/interrupt.h> +#include <linux/delay.h> #include <linux/mtd/mtd.h> #include <linux/mtd/partitions.h> +#include <linux/gpio.h> +#include <linux/err.h> +#include <linux/clk.h> #include <asm/setup.h> #include <asm/memory.h> #include <asm/mach-types.h> -#include <asm/hardware.h> +#include <mach/hardware.h> #include <asm/irq.h> #include <asm/sizes.h> @@ -34,13 +38,13 @@ #include <asm/mach/map.h> #include <asm/mach/irq.h> #include <asm/mach/flash.h> -#include <asm/arch/mmc.h> -#include <asm/arch/udc.h> -#include <asm/arch/gumstix.h> +#include <mach/mmc.h> +#include <mach/udc.h> +#include <mach/gumstix.h> -#include <asm/arch/pxa-regs.h> -#include <asm/arch/pxa2xx-regs.h> -#include <asm/arch/pxa2xx-gpio.h> +#include <mach/pxa-regs.h> +#include <mach/pxa2xx-regs.h> +#include <mach/mfp-pxa25x.h> #include "generic.h" @@ -85,21 +89,8 @@ static struct platform_device *devices[] __initdata = { }; #ifdef CONFIG_MMC_PXA -static struct pxamci_platform_data gumstix_mci_platform_data; - -static int gumstix_mci_init(struct device *dev, irq_handler_t detect_int, - void *data) -{ - pxa_gpio_mode(GPIO6_MMCCLK_MD); - pxa_gpio_mode(GPIO53_MMCCLK_MD); - pxa_gpio_mode(GPIO8_MMCCS0_MD); - - return 0; -} - static struct pxamci_platform_data gumstix_mci_platform_data = { .ocr_mask = MMC_VDD_32_33|MMC_VDD_33_34, - .init = gumstix_mci_init, }; static void __init gumstix_mmc_init(void) @@ -109,11 +100,11 @@ static void __init gumstix_mmc_init(void) #else static void __init gumstix_mmc_init(void) { - printk(KERN_INFO "Gumstix mmc disabled\n"); + pr_debug("Gumstix mmc disabled\n"); } #endif -#ifdef CONFIG_USB_GADGET_PXA2XX +#ifdef CONFIG_USB_GADGET_PXA25X static struct pxa2xx_udc_mach_info gumstix_udc_info __initdata = { .gpio_vbus = GPIO_GUMSTIX_USB_GPIOn, .gpio_pullup = GPIO_GUMSTIX_USB_GPIOx, @@ -126,12 +117,87 @@ static void __init gumstix_udc_init(void) #else static void gumstix_udc_init(void) { - printk(KERN_INFO "Gumstix udc is disabled\n"); + pr_debug("Gumstix udc is disabled\n"); } #endif +#ifdef CONFIG_BT +/* Normally, the bootloader would have enabled this 32kHz clock but many +** boards still have u-boot 1.1.4 so we check if it has been turned on and +** if not, we turn it on with a warning message. */ +static void gumstix_setup_bt_clock(void) +{ + int timeout = 500; + + if (!(OSCC & OSCC_OOK)) + pr_warning("32kHz clock was not on. Bootloader may need to " + "be updated\n"); + else + return; + + OSCC |= OSCC_OON; + do { + if (OSCC & OSCC_OOK) + break; + udelay(1); + } while (--timeout); + if (!timeout) + pr_err("Failed to start 32kHz clock\n"); +} + +static void __init gumstix_bluetooth_init(void) +{ + int err; + + gumstix_setup_bt_clock(); + + err = gpio_request(GPIO_GUMSTIX_BTRESET, "BTRST"); + if (err) { + pr_err("gumstix: failed request gpio for bluetooth reset\n"); + return; + } + + err = gpio_direction_output(GPIO_GUMSTIX_BTRESET, 1); + if (err) { + pr_err("gumstix: can't reset bluetooth\n"); + return; + } + gpio_set_value(GPIO_GUMSTIX_BTRESET, 0); + udelay(100); + gpio_set_value(GPIO_GUMSTIX_BTRESET, 1); +} +#else +static void gumstix_bluetooth_init(void) +{ + pr_debug("Gumstix Bluetooth is disabled\n"); +} +#endif + +static unsigned long gumstix_pin_config[] __initdata = { + GPIO12_32KHz, + /* BTUART */ + GPIO42_HWUART_RXD, + GPIO43_HWUART_TXD, + GPIO44_HWUART_CTS, + GPIO45_HWUART_RTS, + /* MMC */ + GPIO6_MMC_CLK, + GPIO53_MMC_CLK, + GPIO8_MMC_CS0, + /* these are used by AM200EPD */ + GPIO51_GPIO, + GPIO49_GPIO, + GPIO48_GPIO, + GPIO32_GPIO, + GPIO17_GPIO, + GPIO16_GPIO, +}; + static void __init gumstix_init(void) { + pxa2xx_mfp_config(ARRAY_AND_SIZE(gumstix_pin_config)); + + gumstix_bluetooth_init(); gumstix_udc_init(); gumstix_mmc_init(); (void) platform_add_devices(devices, ARRAY_SIZE(devices)); diff --git a/arch/arm/mach-pxa/idp.c b/arch/arm/mach-pxa/idp.c index 2637633f916..013b15baa03 100644 --- a/arch/arm/mach-pxa/idp.c +++ b/arch/arm/mach-pxa/idp.c @@ -25,18 +25,18 @@ #include <asm/setup.h> #include <asm/memory.h> #include <asm/mach-types.h> -#include <asm/hardware.h> +#include <mach/hardware.h> #include <asm/irq.h> #include <asm/mach/arch.h> #include <asm/mach/map.h> -#include <asm/arch/pxa-regs.h> -#include <asm/arch/pxa2xx-gpio.h> -#include <asm/arch/idp.h> -#include <asm/arch/pxafb.h> -#include <asm/arch/bitfield.h> -#include <asm/arch/mmc.h> +#include <mach/pxa-regs.h> +#include <mach/mfp-pxa25x.h> +#include <mach/idp.h> +#include <mach/pxafb.h> +#include <mach/bitfield.h> +#include <mach/mmc.h> #include "generic.h" #include "devices.h" @@ -46,6 +46,47 @@ * - Ethernet interrupt */ +static unsigned long idp_pin_config[] __initdata = { + /* LCD */ + GPIO58_LCD_LDD_0, + GPIO59_LCD_LDD_1, + GPIO60_LCD_LDD_2, + GPIO61_LCD_LDD_3, + GPIO62_LCD_LDD_4, + GPIO63_LCD_LDD_5, + GPIO64_LCD_LDD_6, + GPIO65_LCD_LDD_7, + GPIO66_LCD_LDD_8, + GPIO67_LCD_LDD_9, + GPIO68_LCD_LDD_10, + GPIO69_LCD_LDD_11, + GPIO70_LCD_LDD_12, + GPIO71_LCD_LDD_13, + GPIO72_LCD_LDD_14, + GPIO73_LCD_LDD_15, + GPIO74_LCD_FCLK, + GPIO75_LCD_LCLK, + GPIO76_LCD_PCLK, + + /* BTUART */ + GPIO42_BTUART_RXD, + GPIO43_BTUART_TXD, + GPIO44_BTUART_CTS, + GPIO45_BTUART_RTS, + + /* STUART */ + GPIO46_STUART_RXD, + GPIO47_STUART_TXD, + + /* MMC */ + GPIO6_MMC_CLK, + GPIO8_MMC_CS0, + + /* Ethernet */ + GPIO33_nCS_5, /* Ethernet CS */ + GPIO4_GPIO, /* Ethernet IRQ */ +}; + static struct resource smc91x_resources[] = { [0] = { .start = (IDP_ETH_PHYS + 0x300), @@ -121,44 +162,28 @@ static struct pxafb_mach_info sharp_lm8v31 = { .num_modes = 1, .cmap_inverse = 0, .cmap_static = 0, - .lccr0 = LCCR0_SDS, - .lccr3 = LCCR3_PCP | LCCR3_Acb(255), + .lcd_conn = LCD_COLOR_DSTN_16BPP | LCD_PCLK_EDGE_FALL | + LCD_AC_BIAS_FREQ(255), .pxafb_backlight_power = &idp_backlight_power, .pxafb_lcd_power = &idp_lcd_power }; -static int idp_mci_init(struct device *dev, irq_handler_t idp_detect_int, void *data) -{ - /* setup GPIO for PXA25x MMC controller */ - pxa_gpio_mode(GPIO6_MMCCLK_MD); - pxa_gpio_mode(GPIO8_MMCCS0_MD); - - return 0; -} - static struct pxamci_platform_data idp_mci_platform_data = { .ocr_mask = MMC_VDD_32_33|MMC_VDD_33_34, - .init = idp_mci_init, }; static void __init idp_init(void) { printk("idp_init()\n"); + pxa2xx_mfp_config(ARRAY_AND_SIZE(idp_pin_config)); + platform_device_register(&smc91x_device); //platform_device_register(&mst_audio_device); set_pxa_fb_info(&sharp_lm8v31); pxa_set_mci_info(&idp_mci_platform_data); } -static void __init idp_init_irq(void) -{ - - pxa25x_init_irq(); - - set_irq_type(TOUCH_PANEL_IRQ, TOUCH_PANEL_IRQ_EDGE); -} - static struct map_desc idp_io_desc[] __initdata = { { .virtual = IDP_COREVOLT_VIRT, @@ -177,15 +202,6 @@ static void __init idp_map_io(void) { pxa_map_io(); iotable_init(idp_io_desc, ARRAY_SIZE(idp_io_desc)); - - // serial ports 2 & 3 - pxa_gpio_mode(GPIO42_BTRXD_MD); - pxa_gpio_mode(GPIO43_BTTXD_MD); - pxa_gpio_mode(GPIO44_BTCTS_MD); - pxa_gpio_mode(GPIO45_BTRTS_MD); - pxa_gpio_mode(GPIO46_STRXD_MD); - pxa_gpio_mode(GPIO47_STTXD_MD); - } @@ -194,7 +210,7 @@ MACHINE_START(PXA_IDP, "Vibren PXA255 IDP") .phys_io = 0x40000000, .io_pg_offst = (io_p2v(0x40000000) >> 18) & 0xfffc, .map_io = idp_map_io, - .init_irq = idp_init_irq, + .init_irq = pxa25x_init_irq, .timer = &pxa_timer, .init_machine = idp_init, MACHINE_END diff --git a/arch/arm/mach-pxa/include/mach/audio.h b/arch/arm/mach-pxa/include/mach/audio.h new file mode 100644 index 00000000000..f82f96dd105 --- /dev/null +++ b/arch/arm/mach-pxa/include/mach/audio.h @@ -0,0 +1,17 @@ +#ifndef __ASM_ARCH_AUDIO_H__ +#define __ASM_ARCH_AUDIO_H__ + +#include <sound/core.h> +#include <sound/pcm.h> + +typedef struct { + int (*startup)(struct snd_pcm_substream *, void *); + void (*shutdown)(struct snd_pcm_substream *, void *); + void (*suspend)(void *); + void (*resume)(void *); + void *priv; +} pxa2xx_audio_ops_t; + +extern void pxa_set_ac97_info(pxa2xx_audio_ops_t *ops); + +#endif diff --git a/arch/arm/mach-pxa/include/mach/bitfield.h b/arch/arm/mach-pxa/include/mach/bitfield.h new file mode 100644 index 00000000000..f1f0e3387d9 --- /dev/null +++ b/arch/arm/mach-pxa/include/mach/bitfield.h @@ -0,0 +1,113 @@ +/* + * FILE bitfield.h + * + * Version 1.1 + * Author Copyright (c) Marc A. Viredaz, 1998 + * DEC Western Research Laboratory, Palo Alto, CA + * Date April 1998 (April 1997) + * System Advanced RISC Machine (ARM) + * Language C or ARM Assembly + * Purpose Definition of macros to operate on bit fields. + */ + + + +#ifndef __BITFIELD_H +#define __BITFIELD_H + +#ifndef __ASSEMBLY__ +#define UData(Data) ((unsigned long) (Data)) +#else +#define UData(Data) (Data) +#endif + + +/* + * MACRO: Fld + * + * Purpose + * The macro "Fld" encodes a bit field, given its size and its shift value + * with respect to bit 0. + * + * Note + * A more intuitive way to encode bit fields would have been to use their + * mask. However, extracting size and shift value information from a bit + * field's mask is cumbersome and might break the assembler (255-character + * line-size limit). + * + * Input + * Size Size of the bit field, in number of bits. + * Shft Shift value of the bit field with respect to bit 0. + * + * Output + * Fld Encoded bit field. + */ + +#define Fld(Size, Shft) (((Size) << 16) + (Shft)) + + +/* + * MACROS: FSize, FShft, FMsk, FAlnMsk, F1stBit + * + * Purpose + * The macros "FSize", "FShft", "FMsk", "FAlnMsk", and "F1stBit" return + * the size, shift value, mask, aligned mask, and first bit of a + * bit field. + * + * Input + * Field Encoded bit field (using the macro "Fld"). + * + * Output + * FSize Size of the bit field, in number of bits. + * FShft Shift value of the bit field with respect to bit 0. + * FMsk Mask for the bit field. + * FAlnMsk Mask for the bit field, aligned on bit 0. + * F1stBit First bit of the bit field. + */ + +#define FSize(Field) ((Field) >> 16) +#define FShft(Field) ((Field) & 0x0000FFFF) +#define FMsk(Field) (((UData (1) << FSize (Field)) - 1) << FShft (Field)) +#define FAlnMsk(Field) ((UData (1) << FSize (Field)) - 1) +#define F1stBit(Field) (UData (1) << FShft (Field)) + + +/* + * MACRO: FInsrt + * + * Purpose + * The macro "FInsrt" inserts a value into a bit field by shifting the + * former appropriately. + * + * Input + * Value Bit-field value. + * Field Encoded bit field (using the macro "Fld"). + * + * Output + * FInsrt Bit-field value positioned appropriately. + */ + +#define FInsrt(Value, Field) \ + (UData (Value) << FShft (Field)) + + +/* + * MACRO: FExtr + * + * Purpose + * The macro "FExtr" extracts the value of a bit field by masking and + * shifting it appropriately. + * + * Input + * Data Data containing the bit-field to be extracted. + * Field Encoded bit field (using the macro "Fld"). + * + * Output + * FExtr Bit-field value. + */ + +#define FExtr(Data, Field) \ + ((UData (Data) >> FShft (Field)) & FAlnMsk (Field)) + + +#endif /* __BITFIELD_H */ diff --git a/arch/arm/mach-pxa/include/mach/camera.h b/arch/arm/mach-pxa/include/mach/camera.h new file mode 100644 index 00000000000..39516ced8b1 --- /dev/null +++ b/arch/arm/mach-pxa/include/mach/camera.h @@ -0,0 +1,48 @@ +/* + camera.h - PXA camera driver header file + + Copyright (C) 2003, Intel Corporation + Copyright (C) 2008, Guennadi Liakhovetski <kernel@pengutronix.de> + + This program is free software; you can redistribute it and/or modify + it under the terms of the GNU General Public License as published by + the Free Software Foundation; either version 2 of the License, or + (at your option) any later version. + + This program is distributed in the hope that it will be useful, + but WITHOUT ANY WARRANTY; without even the implied warranty of + MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + GNU General Public License for more details. + + You should have received a copy of the GNU General Public License + along with this program; if not, write to the Free Software + Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA. +*/ + +#ifndef __ASM_ARCH_CAMERA_H_ +#define __ASM_ARCH_CAMERA_H_ + +#define PXA_CAMERA_MASTER 1 +#define PXA_CAMERA_DATAWIDTH_4 2 +#define PXA_CAMERA_DATAWIDTH_5 4 +#define PXA_CAMERA_DATAWIDTH_8 8 +#define PXA_CAMERA_DATAWIDTH_9 0x10 +#define PXA_CAMERA_DATAWIDTH_10 0x20 +#define PXA_CAMERA_PCLK_EN 0x40 +#define PXA_CAMERA_MCLK_EN 0x80 +#define PXA_CAMERA_PCP 0x100 +#define PXA_CAMERA_HSP 0x200 +#define PXA_CAMERA_VSP 0x400 + +struct pxacamera_platform_data { + int (*init)(struct device *); + int (*power)(struct device *, int); + int (*reset)(struct device *, int); + + unsigned long flags; + unsigned long mclk_10khz; +}; + +extern void pxa_set_camera_info(struct pxacamera_platform_data *); + +#endif /* __ASM_ARCH_CAMERA_H_ */ diff --git a/arch/arm/mach-pxa/include/mach/colibri.h b/arch/arm/mach-pxa/include/mach/colibri.h new file mode 100644 index 00000000000..2ae373fb567 --- /dev/null +++ b/arch/arm/mach-pxa/include/mach/colibri.h @@ -0,0 +1,19 @@ +#ifndef _COLIBRI_H_ +#define _COLIBRI_H_ + +/* physical memory regions */ +#define COLIBRI_FLASH_PHYS (PXA_CS0_PHYS) /* Flash region */ +#define COLIBRI_ETH_PHYS (PXA_CS2_PHYS) /* Ethernet DM9000 region */ +#define COLIBRI_SDRAM_BASE 0xa0000000 /* SDRAM region */ + +/* virtual memory regions */ +#define COLIBRI_DISK_VIRT 0xF0000000 /* Disk On Chip region */ + +/* size of flash */ +#define COLIBRI_FLASH_SIZE 0x02000000 /* Flash size 32 MB */ + +/* Ethernet Controller Davicom DM9000 */ +#define GPIO_DM9000 114 +#define COLIBRI_ETH_IRQ IRQ_GPIO(GPIO_DM9000) + +#endif /* _COLIBRI_H_ */ diff --git a/arch/arm/mach-pxa/include/mach/corgi.h b/arch/arm/mach-pxa/include/mach/corgi.h new file mode 100644 index 00000000000..585970ef08c --- /dev/null +++ b/arch/arm/mach-pxa/include/mach/corgi.h @@ -0,0 +1,118 @@ +/* + * Hardware specific definitions for SL-C7xx series of PDAs + * + * Copyright (c) 2004-2005 Richard Purdie + * + * Based on Sharp's 2.4 kernel patches + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + * + */ +#ifndef __ASM_ARCH_CORGI_H +#define __ASM_ARCH_CORGI_H 1 + + +/* + * Corgi (Non Standard) GPIO Definitions + */ +#define CORGI_GPIO_KEY_INT (0) /* Keyboard Interrupt */ +#define CORGI_GPIO_AC_IN (1) /* Charger Detection */ +#define CORGI_GPIO_WAKEUP (3) /* System wakeup notification? */ +#define CORGI_GPIO_AK_INT (4) /* Headphone Jack Control Interrupt */ +#define CORGI_GPIO_TP_INT (5) /* Touch Panel Interrupt */ +#define CORGI_GPIO_nSD_WP (7) /* SD Write Protect? */ +#define CORGI_GPIO_nSD_DETECT (9) /* MMC/SD Card Detect */ +#define CORGI_GPIO_nSD_INT (10) /* SD Interrupt for SDIO? */ +#define CORGI_GPIO_MAIN_BAT_LOW (11) /* Main Battery Low Notification */ +#define CORGI_GPIO_BAT_COVER (11) /* Battery Cover Detect */ +#define CORGI_GPIO_LED_ORANGE (13) /* Orange LED Control */ +#define CORGI_GPIO_CF_CD (14) /* Compact Flash Card Detect */ +#define CORGI_GPIO_CHRG_FULL (16) /* Charging Complete Notification */ +#define CORGI_GPIO_CF_IRQ (17) /* Compact Flash Interrupt */ +#define CORGI_GPIO_LCDCON_CS (19) /* LCD Control Chip Select */ +#define CORGI_GPIO_MAX1111_CS (20) /* MAX1111 Chip Select */ +#define CORGI_GPIO_ADC_TEMP_ON (21) /* Select battery voltage or temperature */ +#define CORGI_GPIO_IR_ON (22) /* Enable IR Transciever */ +#define CORGI_GPIO_ADS7846_CS (24) /* ADS7846 Chip Select */ +#define CORGI_GPIO_SD_PWR (33) /* MMC/SD Power */ +#define CORGI_GPIO_CHRG_ON (38) /* Enable battery Charging */ +#define CORGI_GPIO_DISCHARGE_ON (42) /* Enable battery Discharge */ +#define CORGI_GPIO_CHRG_UKN (43) /* Unknown Charging (Bypass Control?) */ +#define CORGI_GPIO_HSYNC (44) /* LCD HSync Pulse */ +#define CORGI_GPIO_USB_PULLUP (45) /* USB show presence to host */ + + +/* + * Corgi Keyboard Definitions + */ +#define CORGI_KEY_STROBE_NUM (12) +#define CORGI_KEY_SENSE_NUM (8) +#define CORGI_GPIO_ALL_STROBE_BIT (0x00003ffc) +#define CORGI_GPIO_HIGH_SENSE_BIT (0xfc000000) +#define CORGI_GPIO_HIGH_SENSE_RSHIFT (26) +#define CORGI_GPIO_LOW_SENSE_BIT (0x00000003) +#define CORGI_GPIO_LOW_SENSE_LSHIFT (6) +#define CORGI_GPIO_STROBE_BIT(a) GPIO_bit(66+(a)) +#define CORGI_GPIO_SENSE_BIT(a) GPIO_bit(58+(a)) +#define CORGI_GAFR_ALL_STROBE_BIT (0x0ffffff0) +#define CORGI_GAFR_HIGH_SENSE_BIT (0xfff00000) +#define CORGI_GAFR_LOW_SENSE_BIT (0x0000000f) +#define CORGI_GPIO_KEY_SENSE(a) (58+(a)) +#define CORGI_GPIO_KEY_STROBE(a) (66+(a)) + + +/* + * Corgi Interrupts + */ +#define CORGI_IRQ_GPIO_KEY_INT IRQ_GPIO(0) +#define CORGI_IRQ_GPIO_AC_IN IRQ_GPIO(1) +#define CORGI_IRQ_GPIO_WAKEUP IRQ_GPIO(3) +#define CORGI_IRQ_GPIO_AK_INT IRQ_GPIO(4) +#define CORGI_IRQ_GPIO_TP_INT IRQ_GPIO(5) +#define CORGI_IRQ_GPIO_nSD_DETECT IRQ_GPIO(9) +#define CORGI_IRQ_GPIO_nSD_INT IRQ_GPIO(10) +#define CORGI_IRQ_GPIO_MAIN_BAT_LOW IRQ_GPIO(11) +#define CORGI_IRQ_GPIO_CF_CD IRQ_GPIO(14) +#define CORGI_IRQ_GPIO_CHRG_FULL IRQ_GPIO(16) /* Battery fully charged */ +#define CORGI_IRQ_GPIO_CF_IRQ IRQ_GPIO(17) +#define CORGI_IRQ_GPIO_KEY_SENSE(a) IRQ_GPIO(58+(a)) /* Keyboard Sense lines */ + + +/* + * Corgi SCOOP GPIOs and Config + */ +#define CORGI_SCP_LED_GREEN SCOOP_GPCR_PA11 +#define CORGI_SCP_SWA SCOOP_GPCR_PA12 /* Hinge Switch A */ +#define CORGI_SCP_SWB SCOOP_GPCR_PA13 /* Hinge Switch B */ +#define CORGI_SCP_MUTE_L SCOOP_GPCR_PA14 +#define CORGI_SCP_MUTE_R SCOOP_GPCR_PA15 +#define CORGI_SCP_AKIN_PULLUP SCOOP_GPCR_PA16 +#define CORGI_SCP_APM_ON SCOOP_GPCR_PA17 +#define CORGI_SCP_BACKLIGHT_CONT SCOOP_GPCR_PA18 +#define CORGI_SCP_MIC_BIAS SCOOP_GPCR_PA19 + +#define CORGI_SCOOP_IO_DIR ( CORGI_SCP_LED_GREEN | CORGI_SCP_MUTE_L | CORGI_SCP_MUTE_R | \ + CORGI_SCP_AKIN_PULLUP | CORGI_SCP_APM_ON | CORGI_SCP_BACKLIGHT_CONT | \ + CORGI_SCP_MIC_BIAS ) +#define CORGI_SCOOP_IO_OUT ( CORGI_SCP_MUTE_L | CORGI_SCP_MUTE_R ) + +#define CORGI_SCOOP_GPIO_BASE (NR_BUILTIN_GPIO) +#define CORGI_GPIO_LED_GREEN (CORGI_SCOOP_GPIO_BASE + 0) +#define CORGI_GPIO_SWA (CORGI_SCOOP_GPIO_BASE + 1) /* Hinge Switch A */ +#define CORGI_GPIO_SWB (CORGI_SCOOP_GPIO_BASE + 2) /* Hinge Switch B */ +#define CORGI_GPIO_MUTE_L (CORGI_SCOOP_GPIO_BASE + 3) +#define CORGI_GPIO_MUTE_R (CORGI_SCOOP_GPIO_BASE + 4) +#define CORGI_GPIO_AKIN_PULLUP (CORGI_SCOOP_GPIO_BASE + 5) +#define CORGI_GPIO_APM_ON (CORGI_SCOOP_GPIO_BASE + 6) +#define CORGI_GPIO_BACKLIGHT_CONT (CORGI_SCOOP_GPIO_BASE + 7) +#define CORGI_GPIO_MIC_BIAS (CORGI_SCOOP_GPIO_BASE + 8) + +/* + * Shared data structures + */ +extern struct platform_device corgiscoop_device; + +#endif /* __ASM_ARCH_CORGI_H */ + diff --git a/arch/arm/mach-pxa/include/mach/debug-macro.S b/arch/arm/mach-pxa/include/mach/debug-macro.S new file mode 100644 index 00000000000..55d6a175ab1 --- /dev/null +++ b/arch/arm/mach-pxa/include/mach/debug-macro.S @@ -0,0 +1,25 @@ +/* arch/arm/mach-pxa/include/mach/debug-macro.S + * + * Debugging macro include header + * + * Copyright (C) 1994-1999 Russell King + * Moved from linux/arch/arm/kernel/debug.S by Ben Dooks + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + * +*/ + +#include "hardware.h" + + .macro addruart,rx + mrc p15, 0, \rx, c1, c0 + tst \rx, #1 @ MMU enabled? + moveq \rx, #0x40000000 @ physical + movne \rx, #io_p2v(0x40000000) @ virtual + orr \rx, \rx, #0x00100000 + .endm + +#define UART_SHIFT 2 +#include <asm/hardware/debug-8250.S> diff --git a/arch/arm/mach-pxa/include/mach/dma.h b/arch/arm/mach-pxa/include/mach/dma.h new file mode 100644 index 00000000000..955bfe60606 --- /dev/null +++ b/arch/arm/mach-pxa/include/mach/dma.h @@ -0,0 +1,50 @@ +/* + * arch/arm/mach-pxa/include/mach/dma.h + * + * Author: Nicolas Pitre + * Created: Jun 15, 2001 + * Copyright: MontaVista Software, Inc. + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ +#ifndef __ASM_ARCH_DMA_H +#define __ASM_ARCH_DMA_H + +/* + * Descriptor structure for PXA's DMA engine + * Note: this structure must always be aligned to a 16-byte boundary. + */ + +typedef struct pxa_dma_desc { + volatile u32 ddadr; /* Points to the next descriptor + flags */ + volatile u32 dsadr; /* DSADR value for the current transfer */ + volatile u32 dtadr; /* DTADR value for the current transfer */ + volatile u32 dcmd; /* DCMD value for the current transfer */ +} pxa_dma_desc; + +typedef enum { + DMA_PRIO_HIGH = 0, + DMA_PRIO_MEDIUM = 1, + DMA_PRIO_LOW = 2 +} pxa_dma_prio; + +#if defined(CONFIG_MACH_ARMCORE) && defined(CONFIG_PCI) +#define HAVE_ARCH_PCI_SET_DMA_MASK 1 +#endif + +/* + * DMA registration + */ + +int __init pxa_init_dma(int num_ch); + +int pxa_request_dma (char *name, + pxa_dma_prio prio, + void (*irq_handler)(int, void *), + void *data); + +void pxa_free_dma (int dma_ch); + +#endif /* _ASM_ARCH_DMA_H */ diff --git a/arch/arm/mach-pxa/include/mach/entry-macro.S b/arch/arm/mach-pxa/include/mach/entry-macro.S new file mode 100644 index 00000000000..f6b4bf3e73d --- /dev/null +++ b/arch/arm/mach-pxa/include/mach/entry-macro.S @@ -0,0 +1,57 @@ +/* + * arch/arm/mach-pxa/include/mach/entry-macro.S + * + * Low-level IRQ helper macros for PXA-based platforms + * + * This file is licensed under the terms of the GNU General Public + * License version 2. This program is licensed "as is" without any + * warranty of any kind, whether express or implied. + */ +#include <mach/hardware.h> +#include <mach/irqs.h> + + .macro disable_fiq + .endm + + .macro get_irqnr_preamble, base, tmp + .endm + + .macro arch_ret_to_user, tmp1, tmp2 + .endm + + .macro get_irqnr_and_base, irqnr, irqstat, base, tmp + mrc p15, 0, \tmp, c0, c0, 0 @ CPUID + mov \tmp, \tmp, lsr #13 + and \tmp, \tmp, #0x7 @ Core G + cmp \tmp, #1 + bhi 1004f + + mov \base, #io_p2v(0x40000000) @ IIR Ctl = 0x40d00000 + add \base, \base, #0x00d00000 + ldr \irqstat, [\base, #0] @ ICIP + ldr \irqnr, [\base, #4] @ ICMR + b 1002f + +1004: + mrc p6, 0, \irqstat, c6, c0, 0 @ ICIP2 + mrc p6, 0, \irqnr, c7, c0, 0 @ ICMR2 + ands \irqnr, \irqstat, \irqnr + beq 1003f + rsb \irqstat, \irqnr, #0 + and \irqstat, \irqstat, \irqnr + clz \irqnr, \irqstat + rsb \irqnr, \irqnr, #31 + add \irqnr, \irqnr, #(32 + PXA_IRQ(0)) + b 1001f +1003: + mrc p6, 0, \irqstat, c0, c0, 0 @ ICIP + mrc p6, 0, \irqnr, c1, c0, 0 @ ICMR +1002: + ands \irqnr, \irqstat, \irqnr + beq 1001f + rsb \irqstat, \irqnr, #0 + and \irqstat, \irqstat, \irqnr + clz \irqnr, \irqstat + rsb \irqnr, \irqnr, #(31 + PXA_IRQ(0)) +1001: + .endm diff --git a/arch/arm/mach-pxa/include/mach/eseries-gpio.h b/arch/arm/mach-pxa/include/mach/eseries-gpio.h new file mode 100644 index 00000000000..4c90b131027 --- /dev/null +++ b/arch/arm/mach-pxa/include/mach/eseries-gpio.h @@ -0,0 +1,50 @@ +/* + * eseries-gpio.h + * + * Copyright (C) Ian Molton <spyro@f2s.com> + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + * + */ + +/* e-series power button */ +#define GPIO_ESERIES_POWERBTN 0 + +/* UDC GPIO definitions */ +#define GPIO_E7XX_USB_DISC 13 +#define GPIO_E7XX_USB_PULLUP 3 + +#define GPIO_E800_USB_DISC 4 +#define GPIO_E800_USB_PULLUP 84 + +/* e740 PCMCIA GPIO definitions */ +/* Note: PWR1 seems to be inverted */ +#define GPIO_E740_PCMCIA_CD0 8 +#define GPIO_E740_PCMCIA_CD1 44 +#define GPIO_E740_PCMCIA_RDY0 11 +#define GPIO_E740_PCMCIA_RDY1 6 +#define GPIO_E740_PCMCIA_RST0 27 +#define GPIO_E740_PCMCIA_RST1 24 +#define GPIO_E740_PCMCIA_PWR0 20 +#define GPIO_E740_PCMCIA_PWR1 23 + +/* e750 PCMCIA GPIO definitions */ +#define GPIO_E750_PCMCIA_CD0 8 +#define GPIO_E750_PCMCIA_RDY0 12 +#define GPIO_E750_PCMCIA_RST0 27 +#define GPIO_E750_PCMCIA_PWR0 20 + +/* e800 PCMCIA GPIO definitions */ +#define GPIO_E800_PCMCIA_RST0 69 +#define GPIO_E800_PCMCIA_RST1 72 +#define GPIO_E800_PCMCIA_PWR0 20 +#define GPIO_E800_PCMCIA_PWR1 73 + +/* e7xx IrDA power control */ +#define GPIO_E7XX_IR_ON 38 + +/* ASIC related GPIOs */ +#define GPIO_ESERIES_TMIO_IRQ 5 +#define GPIO_E800_ANGELX_IRQ 8 diff --git a/arch/arm/mach-pxa/include/mach/eseries-irq.h b/arch/arm/mach-pxa/include/mach/eseries-irq.h new file mode 100644 index 00000000000..f2a93d5e31d --- /dev/null +++ b/arch/arm/mach-pxa/include/mach/eseries-irq.h @@ -0,0 +1,27 @@ +/* + * eseries-irq.h + * + * Copyright (C) Ian Molton <spyro@f2s.com> + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + * + */ + +#define ANGELX_IRQ_BASE (IRQ_BOARD_START+8) +#define IRQ_ANGELX(n) (ANGELX_IRQ_BASE + (n)) + +#define ANGELX_RDY0_IRQ IRQ_ANGELX(0) +#define ANGELX_ST0_IRQ IRQ_ANGELX(1) +#define ANGELX_CD0_IRQ IRQ_ANGELX(2) +#define ANGELX_RDY1_IRQ IRQ_ANGELX(3) +#define ANGELX_ST1_IRQ IRQ_ANGELX(4) +#define ANGELX_CD1_IRQ IRQ_ANGELX(5) + +#define TMIO_IRQ_BASE (IRQ_BOARD_START+0) +#define IRQ_TMIO(n) (TMIO_IRQ_BASE + (n)) + +#define TMIO_SD_IRQ IRQ_TMIO(1) +#define TMIO_USB_IRQ IRQ_TMIO(2) + diff --git a/arch/arm/mach-pxa/include/mach/gpio.h b/arch/arm/mach-pxa/include/mach/gpio.h new file mode 100644 index 00000000000..2c538d8c362 --- /dev/null +++ b/arch/arm/mach-pxa/include/mach/gpio.h @@ -0,0 +1,65 @@ +/* + * arch/arm/mach-pxa/include/mach/gpio.h + * + * PXA GPIO wrappers for arch-neutral GPIO calls + * + * Written by Philipp Zabel <philipp.zabel@gmail.com> + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA + * + */ + +#ifndef __ASM_ARCH_PXA_GPIO_H +#define __ASM_ARCH_PXA_GPIO_H + +#include <mach/pxa-regs.h> +#include <asm/irq.h> +#include <mach/hardware.h> + +#include <asm-generic/gpio.h> + + +/* NOTE: some PXAs have fewer on-chip GPIOs (like PXA255, with 85). + * Those cases currently cause holes in the GPIO number space. + */ +#define NR_BUILTIN_GPIO 128 + +static inline int gpio_get_value(unsigned gpio) +{ + if (__builtin_constant_p(gpio) && (gpio < NR_BUILTIN_GPIO)) + return GPLR(gpio) & GPIO_bit(gpio); + else + return __gpio_get_value(gpio); +} + +static inline void gpio_set_value(unsigned gpio, int value) +{ + if (__builtin_constant_p(gpio) && (gpio < NR_BUILTIN_GPIO)) { + if (value) + GPSR(gpio) = GPIO_bit(gpio); + else + GPCR(gpio) = GPIO_bit(gpio); + } else { + __gpio_set_value(gpio, value); + } +} + +#define gpio_cansleep __gpio_cansleep + +#define gpio_to_irq(gpio) IRQ_GPIO(gpio) +#define irq_to_gpio(irq) IRQ_TO_GPIO(irq) + + +#endif diff --git a/arch/arm/mach-pxa/include/mach/gumstix.h b/arch/arm/mach-pxa/include/mach/gumstix.h new file mode 100644 index 00000000000..42ee1956750 --- /dev/null +++ b/arch/arm/mach-pxa/include/mach/gumstix.h @@ -0,0 +1,96 @@ +/* + * arch/arm/mach-pxa/include/mach/gumstix.h + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ + + +/* BTRESET - Reset line to Bluetooth module, active low signal. */ +#define GPIO_GUMSTIX_BTRESET 7 +#define GPIO_GUMSTIX_BTRESET_MD (GPIO_GUMSTIX_BTRESET | GPIO_OUT) + + +/* +GPIOn - Input from MAX823 (or equiv), normalizing USB +5V into a clean +interrupt signal for determining cable presence. On the original gumstix, +this is GPIO81, and GPIO83 needs to be defined as well. On the gumstix F, +this moves to GPIO17 and GPIO37. */ + +/* GPIOx - Connects to USB D+ and used as a pull-up after GPIOn +has detected a cable insertion; driven low otherwise. */ + +#ifdef CONFIG_ARCH_GUMSTIX_ORIG + +#define GPIO_GUMSTIX_USB_GPIOn 81 +#define GPIO_GUMSTIX_USB_GPIOx 83 + +#else + +#define GPIO_GUMSTIX_USB_GPIOn 35 +#define GPIO_GUMSTIX_USB_GPIOx 41 + +#endif + +/* usb state change */ +#define GUMSTIX_USB_INTR_IRQ IRQ_GPIO(GPIO_GUMSTIX_USB_GPIOn) + +#define GPIO_GUMSTIX_USB_GPIOn_MD (GPIO_GUMSTIX_USB_GPIOn | GPIO_IN) +#define GPIO_GUMSTIX_USB_GPIOx_CON_MD (GPIO_GUMSTIX_USB_GPIOx | GPIO_OUT) +#define GPIO_GUMSTIX_USB_GPIOx_DIS_MD (GPIO_GUMSTIX_USB_GPIOx | GPIO_IN) + +/* + * SD/MMC definitions + */ +#define GUMSTIX_GPIO_nSD_WP 22 /* SD Write Protect */ +#define GUMSTIX_GPIO_nSD_DETECT 11 /* MMC/SD Card Detect */ +#define GUMSTIX_IRQ_GPIO_nSD_DETECT IRQ_GPIO(GUMSTIX_GPIO_nSD_DETECT) + +/* + * SMC Ethernet definitions + * ETH_RST provides a hardware reset line to the ethernet chip + * ETH is the IRQ line in from the ethernet chip to the PXA + */ +#define GPIO_GUMSTIX_ETH0_RST 80 +#define GPIO_GUMSTIX_ETH0_RST_MD (GPIO_GUMSTIX_ETH0_RST | GPIO_OUT) +#define GPIO_GUMSTIX_ETH1_RST 52 +#define GPIO_GUMSTIX_ETH1_RST_MD (GPIO_GUMSTIX_ETH1_RST | GPIO_OUT) + +#define GPIO_GUMSTIX_ETH0 36 +#define GPIO_GUMSTIX_ETH0_MD (GPIO_GUMSTIX_ETH0 | GPIO_IN) +#define GUMSTIX_ETH0_IRQ IRQ_GPIO(GPIO_GUMSTIX_ETH0) +#define GPIO_GUMSTIX_ETH1 27 +#define GPIO_GUMSTIX_ETH1_MD (GPIO_GUMSTIX_ETH1 | GPIO_IN) +#define GUMSTIX_ETH1_IRQ IRQ_GPIO(GPIO_GUMSTIX_ETH1) + + +/* CF reset line */ +#define GPIO8_RESET 8 + +/* CF slot 0 */ +#define GPIO4_nBVD1 4 +#define GPIO4_nSTSCHG GPIO4_nBVD1 +#define GPIO11_nCD 11 +#define GPIO26_PRDY_nBSY 26 +#define GUMSTIX_S0_nSTSCHG_IRQ IRQ_GPIO(GPIO4_nSTSCHG) +#define GUMSTIX_S0_nCD_IRQ IRQ_GPIO(GPIO11_nCD) +#define GUMSTIX_S0_PRDY_nBSY_IRQ IRQ_GPIO(GPIO26_PRDY_nBSY) + +/* CF slot 1 */ +#define GPIO18_nBVD1 18 +#define GPIO18_nSTSCHG GPIO18_nBVD1 +#define GPIO36_nCD 36 +#define GPIO27_PRDY_nBSY 27 +#define GUMSTIX_S1_nSTSCHG_IRQ IRQ_GPIO(GPIO18_nSTSCHG) +#define GUMSTIX_S1_nCD_IRQ IRQ_GPIO(GPIO36_nCD) +#define GUMSTIX_S1_PRDY_nBSY_IRQ IRQ_GPIO(GPIO27_PRDY_nBSY) + +/* CF GPIO line modes */ +#define GPIO4_nSTSCHG_MD (GPIO4_nSTSCHG | GPIO_IN) +#define GPIO8_RESET_MD (GPIO8_RESET | GPIO_OUT) +#define GPIO11_nCD_MD (GPIO11_nCD | GPIO_IN) +#define GPIO18_nSTSCHG_MD (GPIO18_nSTSCHG | GPIO_IN) +#define GPIO26_PRDY_nBSY_MD (GPIO26_PRDY_nBSY | GPIO_IN) +#define GPIO27_PRDY_nBSY_MD (GPIO27_PRDY_nBSY | GPIO_IN) +#define GPIO36_nCD_MD (GPIO36_nCD | GPIO_IN) diff --git a/arch/arm/mach-pxa/include/mach/hardware.h b/arch/arm/mach-pxa/include/mach/hardware.h new file mode 100644 index 00000000000..a582a6d9b92 --- /dev/null +++ b/arch/arm/mach-pxa/include/mach/hardware.h @@ -0,0 +1,290 @@ +/* + * arch/arm/mach-pxa/include/mach/hardware.h + * + * Author: Nicolas Pitre + * Created: Jun 15, 2001 + * Copyright: MontaVista Software Inc. + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ + +#ifndef __ASM_ARCH_HARDWARE_H +#define __ASM_ARCH_HARDWARE_H + +/* + * We requires absolute addresses. + */ +#define PCIO_BASE 0 + +/* + * Workarounds for at least 2 errata so far require this. + * The mapping is set in mach-pxa/generic.c. + */ +#define UNCACHED_PHYS_0 0xff000000 +#define UNCACHED_ADDR UNCACHED_PHYS_0 + +/* + * Intel PXA2xx internal register mapping: + * + * 0x40000000 - 0x41ffffff <--> 0xf2000000 - 0xf3ffffff + * 0x44000000 - 0x45ffffff <--> 0xf4000000 - 0xf5ffffff + * 0x48000000 - 0x49ffffff <--> 0xf6000000 - 0xf7ffffff + * 0x4c000000 - 0x4dffffff <--> 0xf8000000 - 0xf9ffffff + * 0x50000000 - 0x51ffffff <--> 0xfa000000 - 0xfbffffff + * 0x54000000 - 0x55ffffff <--> 0xfc000000 - 0xfdffffff + * 0x58000000 - 0x59ffffff <--> 0xfe000000 - 0xffffffff + * + * Note that not all PXA2xx chips implement all those addresses, and the + * kernel only maps the minimum needed range of this mapping. + */ +#define io_p2v(x) (0xf2000000 + ((x) & 0x01ffffff) + (((x) & 0x1c000000) >> 1)) +#define io_v2p(x) (0x3c000000 + ((x) & 0x01ffffff) + (((x) & 0x0e000000) << 1)) + +#ifndef __ASSEMBLY__ + +# define __REG(x) (*((volatile u32 *)io_p2v(x))) + +/* With indexed regs we don't want to feed the index through io_p2v() + especially if it is a variable, otherwise horrible code will result. */ +# define __REG2(x,y) \ + (*(volatile u32 *)((u32)&__REG(x) + (y))) + +# define __PREG(x) (io_v2p((u32)&(x))) + +#else + +# define __REG(x) io_p2v(x) +# define __PREG(x) io_v2p(x) + +#endif + +#ifndef __ASSEMBLY__ + +#include <asm/cputype.h> + +/* + * CPU Stepping CPU_ID JTAG_ID + * + * PXA210 B0 0x69052922 0x2926C013 + * PXA210 B1 0x69052923 0x3926C013 + * PXA210 B2 0x69052924 0x4926C013 + * PXA210 C0 0x69052D25 0x5926C013 + * + * PXA250 A0 0x69052100 0x09264013 + * PXA250 A1 0x69052101 0x19264013 + * PXA250 B0 0x69052902 0x29264013 + * PXA250 B1 0x69052903 0x39264013 + * PXA250 B2 0x69052904 0x49264013 + * PXA250 C0 0x69052D05 0x59264013 + * + * PXA255 A0 0x69052D06 0x69264013 + * + * PXA26x A0 0x69052903 0x39264013 + * PXA26x B0 0x69052D05 0x59264013 + * + * PXA27x A0 0x69054110 0x09265013 + * PXA27x A1 0x69054111 0x19265013 + * PXA27x B0 0x69054112 0x29265013 + * PXA27x B1 0x69054113 0x39265013 + * PXA27x C0 0x69054114 0x49265013 + * PXA27x C5 0x69054117 0x79265013 + * + * PXA30x A0 0x69056880 0x0E648013 + * PXA30x A1 0x69056881 0x1E648013 + * PXA31x A0 0x69056890 0x0E649013 + * PXA31x A1 0x69056891 0x1E649013 + * PXA31x A2 0x69056892 0x2E649013 + * PXA32x B1 0x69056825 0x5E642013 + * PXA32x B2 0x69056826 0x6E642013 + * + * PXA930 B0 0x69056835 0x5E643013 + * PXA930 B1 0x69056837 0x7E643013 + * PXA930 B2 0x69056838 0x8E643013 + */ +#ifdef CONFIG_PXA25x +#define __cpu_is_pxa210(id) \ + ({ \ + unsigned int _id = (id) & 0xf3f0; \ + _id == 0x2120; \ + }) + +#define __cpu_is_pxa250(id) \ + ({ \ + unsigned int _id = (id) & 0xf3ff; \ + _id <= 0x2105; \ + }) + +#define __cpu_is_pxa255(id) \ + ({ \ + unsigned int _id = (id) & 0xffff; \ + _id == 0x2d06; \ + }) + +#define __cpu_is_pxa25x(id) \ + ({ \ + unsigned int _id = (id) & 0xf300; \ + _id == 0x2100; \ + }) +#else +#define __cpu_is_pxa210(id) (0) +#define __cpu_is_pxa250(id) (0) +#define __cpu_is_pxa255(id) (0) +#define __cpu_is_pxa25x(id) (0) +#endif + +#ifdef CONFIG_PXA27x +#define __cpu_is_pxa27x(id) \ + ({ \ + unsigned int _id = (id) >> 4 & 0xfff; \ + _id == 0x411; \ + }) +#else +#define __cpu_is_pxa27x(id) (0) +#endif + +#ifdef CONFIG_CPU_PXA300 +#define __cpu_is_pxa300(id) \ + ({ \ + unsigned int _id = (id) >> 4 & 0xfff; \ + _id == 0x688; \ + }) +#else +#define __cpu_is_pxa300(id) (0) +#endif + +#ifdef CONFIG_CPU_PXA310 +#define __cpu_is_pxa310(id) \ + ({ \ + unsigned int _id = (id) >> 4 & 0xfff; \ + _id == 0x689; \ + }) +#else +#define __cpu_is_pxa310(id) (0) +#endif + +#ifdef CONFIG_CPU_PXA320 +#define __cpu_is_pxa320(id) \ + ({ \ + unsigned int _id = (id) >> 4 & 0xfff; \ + _id == 0x603 || _id == 0x682; \ + }) +#else +#define __cpu_is_pxa320(id) (0) +#endif + +#ifdef CONFIG_CPU_PXA930 +#define __cpu_is_pxa930(id) \ + ({ \ + unsigned int _id = (id) >> 4 & 0xfff; \ + _id == 0x683; \ + }) +#else +#define __cpu_is_pxa930(id) (0) +#endif + +#define cpu_is_pxa210() \ + ({ \ + __cpu_is_pxa210(read_cpuid_id()); \ + }) + +#define cpu_is_pxa250() \ + ({ \ + __cpu_is_pxa250(read_cpuid_id()); \ + }) + +#define cpu_is_pxa255() \ + ({ \ + __cpu_is_pxa255(read_cpuid_id()); \ + }) + +#define cpu_is_pxa25x() \ + ({ \ + __cpu_is_pxa25x(read_cpuid_id()); \ + }) + +extern int cpu_is_pxa26x(void); + +#define cpu_is_pxa27x() \ + ({ \ + __cpu_is_pxa27x(read_cpuid_id()); \ + }) + +#define cpu_is_pxa300() \ + ({ \ + __cpu_is_pxa300(read_cpuid_id()); \ + }) + +#define cpu_is_pxa310() \ + ({ \ + __cpu_is_pxa310(read_cpuid_id()); \ + }) + +#define cpu_is_pxa320() \ + ({ \ + __cpu_is_pxa320(read_cpuid_id()); \ + }) + +#define cpu_is_pxa930() \ + ({ \ + unsigned int id = read_cpuid(CPUID_ID); \ + __cpu_is_pxa930(id); \ + }) + +/* + * CPUID Core Generation Bit + * <= 0x2 for pxa21x/pxa25x/pxa26x/pxa27x + * == 0x3 for pxa300/pxa310/pxa320 + */ +#define __cpu_is_pxa2xx(id) \ + ({ \ + unsigned int _id = (id) >> 13 & 0x7; \ + _id <= 0x2; \ + }) + +#define __cpu_is_pxa3xx(id) \ + ({ \ + unsigned int _id = (id) >> 13 & 0x7; \ + _id == 0x3; \ + }) + +#define cpu_is_pxa2xx() \ + ({ \ + __cpu_is_pxa2xx(read_cpuid_id()); \ + }) + +#define cpu_is_pxa3xx() \ + ({ \ + __cpu_is_pxa3xx(read_cpuid_id()); \ + }) + +/* + * Handy routine to set GPIO alternate functions + */ +extern int pxa_gpio_mode( int gpio_mode ); + +/* + * Return GPIO level, nonzero means high, zero is low + */ +extern int pxa_gpio_get_value(unsigned gpio); + +/* + * Set output GPIO level + */ +extern void pxa_gpio_set_value(unsigned gpio, int value); + +/* + * return current memory and LCD clock frequency in units of 10kHz + */ +extern unsigned int get_memclk_frequency_10khz(void); + +#endif + +#if defined(CONFIG_MACH_ARMCORE) && defined(CONFIG_PCI) +#define PCIBIOS_MIN_IO 0 +#define PCIBIOS_MIN_MEM 0 +#define pcibios_assign_all_busses() 1 +#endif + +#endif /* _ASM_ARCH_HARDWARE_H */ diff --git a/arch/arm/mach-pxa/include/mach/i2c.h b/arch/arm/mach-pxa/include/mach/i2c.h new file mode 100644 index 00000000000..1a9f65e6ec0 --- /dev/null +++ b/arch/arm/mach-pxa/include/mach/i2c.h @@ -0,0 +1,82 @@ +/* + * i2c_pxa.h + * + * Copyright (C) 2002 Intrinsyc Software Inc. + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + * + */ +#ifndef _I2C_PXA_H_ +#define _I2C_PXA_H_ + +#if 0 +#define DEF_TIMEOUT 3 +#else +/* need a longer timeout if we're dealing with the fact we may well be + * looking at a multi-master environment +*/ +#define DEF_TIMEOUT 32 +#endif + +#define BUS_ERROR (-EREMOTEIO) +#define XFER_NAKED (-ECONNREFUSED) +#define I2C_RETRY (-2000) /* an error has occurred retry transmit */ + +/* ICR initialize bit values +* +* 15. FM 0 (100 Khz operation) +* 14. UR 0 (No unit reset) +* 13. SADIE 0 (Disables the unit from interrupting on slave addresses +* matching its slave address) +* 12. ALDIE 0 (Disables the unit from interrupt when it loses arbitration +* in master mode) +* 11. SSDIE 0 (Disables interrupts from a slave stop detected, in slave mode) +* 10. BEIE 1 (Enable interrupts from detected bus errors, no ACK sent) +* 9. IRFIE 1 (Enable interrupts from full buffer received) +* 8. ITEIE 1 (Enables the I2C unit to interrupt when transmit buffer empty) +* 7. GCD 1 (Disables i2c unit response to general call messages as a slave) +* 6. IUE 0 (Disable unit until we change settings) +* 5. SCLE 1 (Enables the i2c clock output for master mode (drives SCL) +* 4. MA 0 (Only send stop with the ICR stop bit) +* 3. TB 0 (We are not transmitting a byte initially) +* 2. ACKNAK 0 (Send an ACK after the unit receives a byte) +* 1. STOP 0 (Do not send a STOP) +* 0. START 0 (Do not send a START) +* +*/ +#define I2C_ICR_INIT (ICR_BEIE | ICR_IRFIE | ICR_ITEIE | ICR_GCD | ICR_SCLE) + +/* I2C status register init values + * + * 10. BED 1 (Clear bus error detected) + * 9. SAD 1 (Clear slave address detected) + * 7. IRF 1 (Clear IDBR Receive Full) + * 6. ITE 1 (Clear IDBR Transmit Empty) + * 5. ALD 1 (Clear Arbitration Loss Detected) + * 4. SSD 1 (Clear Slave Stop Detected) + */ +#define I2C_ISR_INIT 0x7FF /* status register init */ + +struct i2c_slave_client; + +struct i2c_pxa_platform_data { + unsigned int slave_addr; + struct i2c_slave_client *slave; + unsigned int class; + unsigned int use_pio :1; + unsigned int fast_mode :1; +}; + +extern void pxa_set_i2c_info(struct i2c_pxa_platform_data *info); + +#ifdef CONFIG_PXA27x +extern void pxa27x_set_i2c_power_info(struct i2c_pxa_platform_data *info); +#endif + +#ifdef CONFIG_PXA3xx +extern void pxa3xx_set_i2c_power_info(struct i2c_pxa_platform_data *info); +#endif + +#endif diff --git a/arch/arm/mach-pxa/include/mach/idp.h b/arch/arm/mach-pxa/include/mach/idp.h new file mode 100644 index 00000000000..5eff96fcc94 --- /dev/null +++ b/arch/arm/mach-pxa/include/mach/idp.h @@ -0,0 +1,199 @@ +/* + * arch/arm/mach-pxa/include/mach/idp.h + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + * + * Copyright (c) 2001 Cliff Brake, Accelent Systems Inc. + * + * 2001-09-13: Cliff Brake <cbrake@accelent.com> + * Initial code + * + * 2005-02-15: Cliff Brake <cliff.brake@gmail.com> + * <http://www.vibren.com> <http://bec-systems.com> + * Changes for 2.6 kernel. + */ + + +/* + * Note: this file must be safe to include in assembly files + * + * Support for the Vibren PXA255 IDP requires rev04 or later + * IDP hardware. + */ + + +#define IDP_FLASH_PHYS (PXA_CS0_PHYS) +#define IDP_ALT_FLASH_PHYS (PXA_CS1_PHYS) +#define IDP_MEDIAQ_PHYS (PXA_CS3_PHYS) +#define IDP_IDE_PHYS (PXA_CS5_PHYS + 0x03000000) +#define IDP_ETH_PHYS (PXA_CS5_PHYS + 0x03400000) +#define IDP_COREVOLT_PHYS (PXA_CS5_PHYS + 0x03800000) +#define IDP_CPLD_PHYS (PXA_CS5_PHYS + 0x03C00000) + + +/* + * virtual memory map + */ + +#define IDP_COREVOLT_VIRT (0xf0000000) +#define IDP_COREVOLT_SIZE (1*1024*1024) + +#define IDP_CPLD_VIRT (IDP_COREVOLT_VIRT + IDP_COREVOLT_SIZE) +#define IDP_CPLD_SIZE (1*1024*1024) + +#if (IDP_CPLD_VIRT + IDP_CPLD_SIZE) > 0xfc000000 +#error Your custom IO space is getting a bit large !! +#endif + +#define CPLD_P2V(x) ((x) - IDP_CPLD_PHYS + IDP_CPLD_VIRT) +#define CPLD_V2P(x) ((x) - IDP_CPLD_VIRT + IDP_CPLD_PHYS) + +#ifndef __ASSEMBLY__ +# define __CPLD_REG(x) (*((volatile unsigned long *)CPLD_P2V(x))) +#else +# define __CPLD_REG(x) CPLD_P2V(x) +#endif + +/* board level registers in the CPLD: (offsets from CPLD_VIRT) */ + +#define _IDP_CPLD_REV (IDP_CPLD_PHYS + 0x00) +#define _IDP_CPLD_PERIPH_PWR (IDP_CPLD_PHYS + 0x04) +#define _IDP_CPLD_LED_CONTROL (IDP_CPLD_PHYS + 0x08) +#define _IDP_CPLD_KB_COL_HIGH (IDP_CPLD_PHYS + 0x0C) +#define _IDP_CPLD_KB_COL_LOW (IDP_CPLD_PHYS + 0x10) +#define _IDP_CPLD_PCCARD_EN (IDP_CPLD_PHYS + 0x14) +#define _IDP_CPLD_GPIOH_DIR (IDP_CPLD_PHYS + 0x18) +#define _IDP_CPLD_GPIOH_VALUE (IDP_CPLD_PHYS + 0x1C) +#define _IDP_CPLD_GPIOL_DIR (IDP_CPLD_PHYS + 0x20) +#define _IDP_CPLD_GPIOL_VALUE (IDP_CPLD_PHYS + 0x24) +#define _IDP_CPLD_PCCARD_PWR (IDP_CPLD_PHYS + 0x28) +#define _IDP_CPLD_MISC_CTRL (IDP_CPLD_PHYS + 0x2C) +#define _IDP_CPLD_LCD (IDP_CPLD_PHYS + 0x30) +#define _IDP_CPLD_FLASH_WE (IDP_CPLD_PHYS + 0x34) + +#define _IDP_CPLD_KB_ROW (IDP_CPLD_PHYS + 0x50) +#define _IDP_CPLD_PCCARD0_STATUS (IDP_CPLD_PHYS + 0x54) +#define _IDP_CPLD_PCCARD1_STATUS (IDP_CPLD_PHYS + 0x58) +#define _IDP_CPLD_MISC_STATUS (IDP_CPLD_PHYS + 0x5C) + +/* FPGA register virtual addresses */ + +#define IDP_CPLD_REV __CPLD_REG(_IDP_CPLD_REV) +#define IDP_CPLD_PERIPH_PWR __CPLD_REG(_IDP_CPLD_PERIPH_PWR) +#define IDP_CPLD_LED_CONTROL __CPLD_REG(_IDP_CPLD_LED_CONTROL) +#define IDP_CPLD_KB_COL_HIGH __CPLD_REG(_IDP_CPLD_KB_COL_HIGH) +#define IDP_CPLD_KB_COL_LOW __CPLD_REG(_IDP_CPLD_KB_COL_LOW) +#define IDP_CPLD_PCCARD_EN __CPLD_REG(_IDP_CPLD_PCCARD_EN) +#define IDP_CPLD_GPIOH_DIR __CPLD_REG(_IDP_CPLD_GPIOH_DIR) +#define IDP_CPLD_GPIOH_VALUE __CPLD_REG(_IDP_CPLD_GPIOH_VALUE) +#define IDP_CPLD_GPIOL_DIR __CPLD_REG(_IDP_CPLD_GPIOL_DIR) +#define IDP_CPLD_GPIOL_VALUE __CPLD_REG(_IDP_CPLD_GPIOL_VALUE) +#define IDP_CPLD_PCCARD_PWR __CPLD_REG(_IDP_CPLD_PCCARD_PWR) +#define IDP_CPLD_MISC_CTRL __CPLD_REG(_IDP_CPLD_MISC_CTRL) +#define IDP_CPLD_LCD __CPLD_REG(_IDP_CPLD_LCD) +#define IDP_CPLD_FLASH_WE __CPLD_REG(_IDP_CPLD_FLASH_WE) + +#define IDP_CPLD_KB_ROW __CPLD_REG(_IDP_CPLD_KB_ROW) +#define IDP_CPLD_PCCARD0_STATUS __CPLD_REG(_IDP_CPLD_PCCARD0_STATUS) +#define IDP_CPLD_PCCARD1_STATUS __CPLD_REG(_IDP_CPLD_PCCARD1_STATUS) +#define IDP_CPLD_MISC_STATUS __CPLD_REG(_IDP_CPLD_MISC_STATUS) + + +/* + * Bit masks for various registers + */ + +// IDP_CPLD_PCCARD_PWR +#define PCC0_PWR0 (1 << 0) +#define PCC0_PWR1 (1 << 1) +#define PCC0_PWR2 (1 << 2) +#define PCC0_PWR3 (1 << 3) +#define PCC1_PWR0 (1 << 4) +#define PCC1_PWR1 (1 << 5) +#define PCC1_PWR2 (1 << 6) +#define PCC1_PWR3 (1 << 7) + +// IDP_CPLD_PCCARD_EN +#define PCC0_RESET (1 << 6) +#define PCC1_RESET (1 << 7) +#define PCC0_ENABLE (1 << 0) +#define PCC1_ENABLE (1 << 1) + +// IDP_CPLD_PCCARDx_STATUS +#define _PCC_WRPROT (1 << 7) // 7-4 read as low true +#define _PCC_RESET (1 << 6) +#define _PCC_IRQ (1 << 5) +#define _PCC_INPACK (1 << 4) +#define PCC_BVD2 (1 << 3) +#define PCC_BVD1 (1 << 2) +#define PCC_VS2 (1 << 1) +#define PCC_VS1 (1 << 0) + +#define PCC_DETECT(x) (GPLR(7 + (x)) & GPIO_bit(7 + (x))) + +/* A listing of interrupts used by external hardware devices */ + +#define TOUCH_PANEL_IRQ IRQ_GPIO(5) +#define IDE_IRQ IRQ_GPIO(21) + +#define TOUCH_PANEL_IRQ_EDGE IRQ_TYPE_EDGE_FALLING + +#define ETHERNET_IRQ IRQ_GPIO(4) +#define ETHERNET_IRQ_EDGE IRQ_TYPE_EDGE_RISING + +#define IDE_IRQ_EDGE IRQ_TYPE_EDGE_RISING + +#define PCMCIA_S0_CD_VALID IRQ_GPIO(7) +#define PCMCIA_S0_CD_VALID_EDGE IRQ_TYPE_EDGE_BOTH + +#define PCMCIA_S1_CD_VALID IRQ_GPIO(8) +#define PCMCIA_S1_CD_VALID_EDGE IRQ_TYPE_EDGE_BOTH + +#define PCMCIA_S0_RDYINT IRQ_GPIO(19) +#define PCMCIA_S1_RDYINT IRQ_GPIO(22) + + +/* + * Macros for LED Driver + */ + +/* leds 0 = ON */ +#define IDP_HB_LED (1<<5) +#define IDP_BUSY_LED (1<<6) + +#define IDP_LEDS_MASK (IDP_HB_LED | IDP_BUSY_LED) + +/* + * macros for MTD driver + */ + +#define FLASH_WRITE_PROTECT_DISABLE() ((IDP_CPLD_FLASH_WE) &= ~(0x1)) +#define FLASH_WRITE_PROTECT_ENABLE() ((IDP_CPLD_FLASH_WE) |= (0x1)) + +/* + * macros for matrix keyboard driver + */ + +#define KEYBD_MATRIX_NUMBER_INPUTS 7 +#define KEYBD_MATRIX_NUMBER_OUTPUTS 14 + +#define KEYBD_MATRIX_INVERT_OUTPUT_LOGIC FALSE +#define KEYBD_MATRIX_INVERT_INPUT_LOGIC FALSE + +#define KEYBD_MATRIX_SETTLING_TIME_US 100 +#define KEYBD_MATRIX_KEYSTATE_DEBOUNCE_CONSTANT 2 + +#define KEYBD_MATRIX_SET_OUTPUTS(outputs) \ +{\ + IDP_CPLD_KB_COL_LOW = outputs;\ + IDP_CPLD_KB_COL_HIGH = outputs >> 7;\ +} + +#define KEYBD_MATRIX_GET_INPUTS(inputs) \ +{\ + inputs = (IDP_CPLD_KB_ROW & 0x7f);\ +} + + diff --git a/arch/arm/mach-pxa/include/mach/io.h b/arch/arm/mach-pxa/include/mach/io.h new file mode 100644 index 00000000000..600fd4f7660 --- /dev/null +++ b/arch/arm/mach-pxa/include/mach/io.h @@ -0,0 +1,20 @@ +/* + * arch/arm/mach-pxa/include/mach/io.h + * + * Copied from asm/arch/sa1100/io.h + */ +#ifndef __ASM_ARM_ARCH_IO_H +#define __ASM_ARM_ARCH_IO_H + +#include <mach/hardware.h> + +#define IO_SPACE_LIMIT 0xffffffff + +/* + * We don't actually have real ISA nor PCI buses, but there is so many + * drivers out there that might just work if we fake them... + */ +#define __io(a) ((void __iomem *)(a)) +#define __mem_pci(a) (a) + +#endif diff --git a/arch/arm/mach-pxa/include/mach/irda.h b/arch/arm/mach-pxa/include/mach/irda.h new file mode 100644 index 00000000000..0a50c3c763d --- /dev/null +++ b/arch/arm/mach-pxa/include/mach/irda.h @@ -0,0 +1,23 @@ +#ifndef ASMARM_ARCH_IRDA_H +#define ASMARM_ARCH_IRDA_H + +/* board specific transceiver capabilities */ + +#define IR_OFF 1 +#define IR_SIRMODE 2 +#define IR_FIRMODE 4 + +struct pxaficp_platform_data { + int transceiver_cap; + void (*transceiver_mode)(struct device *dev, int mode); + int (*startup)(struct device *dev); + void (*shutdown)(struct device *dev); +}; + +extern void pxa_set_ficp_info(struct pxaficp_platform_data *info); + +#if defined(CONFIG_PXA25x) || defined(CONFIG_PXA27x) +void pxa2xx_transceiver_mode(struct device *dev, int mode); +#endif + +#endif diff --git a/arch/arm/mach-pxa/include/mach/irqs.h b/arch/arm/mach-pxa/include/mach/irqs.h new file mode 100644 index 00000000000..9c163e19ada --- /dev/null +++ b/arch/arm/mach-pxa/include/mach/irqs.h @@ -0,0 +1,266 @@ +/* + * arch/arm/mach-pxa/include/mach/irqs.h + * + * Author: Nicolas Pitre + * Created: Jun 15, 2001 + * Copyright: MontaVista Software Inc. + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ + + +#ifdef CONFIG_PXA_HAVE_ISA_IRQS +#define PXA_ISA_IRQ(x) (x) +#define PXA_ISA_IRQ_NUM (16) +#else +#define PXA_ISA_IRQ_NUM (0) +#endif + +#define PXA_IRQ(x) (PXA_ISA_IRQ_NUM + (x)) + +#if defined(CONFIG_PXA27x) || defined(CONFIG_PXA3xx) +#define IRQ_SSP3 PXA_IRQ(0) /* SSP3 service request */ +#define IRQ_MSL PXA_IRQ(1) /* MSL Interface interrupt */ +#define IRQ_USBH2 PXA_IRQ(2) /* USB Host interrupt 1 (OHCI) */ +#define IRQ_USBH1 PXA_IRQ(3) /* USB Host interrupt 2 (non-OHCI) */ +#define IRQ_KEYPAD PXA_IRQ(4) /* Key pad controller */ +#define IRQ_MEMSTK PXA_IRQ(5) /* Memory Stick interrupt */ +#define IRQ_PWRI2C PXA_IRQ(6) /* Power I2C interrupt */ +#endif + +#define IRQ_HWUART PXA_IRQ(7) /* HWUART Transmit/Receive/Error (PXA26x) */ +#define IRQ_OST_4_11 PXA_IRQ(7) /* OS timer 4-11 matches (PXA27x) */ +#define IRQ_GPIO0 PXA_IRQ(8) /* GPIO0 Edge Detect */ +#define IRQ_GPIO1 PXA_IRQ(9) /* GPIO1 Edge Detect */ +#define IRQ_GPIO_2_x PXA_IRQ(10) /* GPIO[2-x] Edge Detect */ +#define IRQ_USB PXA_IRQ(11) /* USB Service */ +#define IRQ_PMU PXA_IRQ(12) /* Performance Monitoring Unit */ +#define IRQ_I2S PXA_IRQ(13) /* I2S Interrupt */ +#define IRQ_AC97 PXA_IRQ(14) /* AC97 Interrupt */ +#define IRQ_ASSP PXA_IRQ(15) /* Audio SSP Service Request (PXA25x) */ +#define IRQ_USIM PXA_IRQ(15) /* Smart Card interface interrupt (PXA27x) */ +#define IRQ_NSSP PXA_IRQ(16) /* Network SSP Service Request (PXA25x) */ +#define IRQ_SSP2 PXA_IRQ(16) /* SSP2 interrupt (PXA27x) */ +#define IRQ_LCD PXA_IRQ(17) /* LCD Controller Service Request */ +#define IRQ_I2C PXA_IRQ(18) /* I2C Service Request */ +#define IRQ_ICP PXA_IRQ(19) /* ICP Transmit/Receive/Error */ +#define IRQ_STUART PXA_IRQ(20) /* STUART Transmit/Receive/Error */ +#define IRQ_BTUART PXA_IRQ(21) /* BTUART Transmit/Receive/Error */ +#define IRQ_FFUART PXA_IRQ(22) /* FFUART Transmit/Receive/Error*/ +#define IRQ_MMC PXA_IRQ(23) /* MMC Status/Error Detection */ +#define IRQ_SSP PXA_IRQ(24) /* SSP Service Request */ +#define IRQ_DMA PXA_IRQ(25) /* DMA Channel Service Request */ +#define IRQ_OST0 PXA_IRQ(26) /* OS Timer match 0 */ +#define IRQ_OST1 PXA_IRQ(27) /* OS Timer match 1 */ +#define IRQ_OST2 PXA_IRQ(28) /* OS Timer match 2 */ +#define IRQ_OST3 PXA_IRQ(29) /* OS Timer match 3 */ +#define IRQ_RTC1Hz PXA_IRQ(30) /* RTC HZ Clock Tick */ +#define IRQ_RTCAlrm PXA_IRQ(31) /* RTC Alarm */ + +#if defined(CONFIG_PXA27x) || defined(CONFIG_PXA3xx) +#define IRQ_TPM PXA_IRQ(32) /* TPM interrupt */ +#define IRQ_CAMERA PXA_IRQ(33) /* Camera Interface */ +#endif + +#ifdef CONFIG_PXA3xx +#define IRQ_SSP4 PXA_IRQ(13) /* SSP4 service request */ +#define IRQ_CIR PXA_IRQ(34) /* Consumer IR */ +#define IRQ_TSI PXA_IRQ(36) /* Touch Screen Interface (PXA320) */ +#define IRQ_USIM2 PXA_IRQ(38) /* USIM2 Controller */ +#define IRQ_GRPHICS PXA_IRQ(39) /* Graphics Controller */ +#define IRQ_MMC2 PXA_IRQ(41) /* MMC2 Controller */ +#define IRQ_1WIRE PXA_IRQ(44) /* 1-Wire Controller */ +#define IRQ_NAND PXA_IRQ(45) /* NAND Controller */ +#define IRQ_USB2 PXA_IRQ(46) /* USB 2.0 Device Controller */ +#define IRQ_WAKEUP0 PXA_IRQ(49) /* EXT_WAKEUP0 */ +#define IRQ_WAKEUP1 PXA_IRQ(50) /* EXT_WAKEUP1 */ +#define IRQ_DMEMC PXA_IRQ(51) /* Dynamic Memory Controller */ +#define IRQ_MMC3 PXA_IRQ(55) /* MMC3 Controller (PXA310) */ +#endif + +#define PXA_GPIO_IRQ_BASE PXA_IRQ(64) +#define PXA_GPIO_IRQ_NUM (128) + +#define GPIO_2_x_TO_IRQ(x) (PXA_GPIO_IRQ_BASE + (x)) +#define IRQ_GPIO(x) (((x) < 2) ? (IRQ_GPIO0 + (x)) : GPIO_2_x_TO_IRQ(x)) + +#define IRQ_TO_GPIO_2_x(i) ((i) - PXA_GPIO_IRQ_BASE) +#define IRQ_TO_GPIO(i) (((i) < IRQ_GPIO(2)) ? ((i) - IRQ_GPIO0) : IRQ_TO_GPIO_2_x(i)) + +/* + * The next 16 interrupts are for board specific purposes. Since + * the kernel can only run on one machine at a time, we can re-use + * these. If you need more, increase IRQ_BOARD_END, but keep it + * within sensible limits. + */ +#define IRQ_BOARD_START (PXA_GPIO_IRQ_BASE + PXA_GPIO_IRQ_NUM) +#define IRQ_BOARD_END (IRQ_BOARD_START + 16) + +#define IRQ_SA1111_START (IRQ_BOARD_END) +#define IRQ_GPAIN0 (IRQ_BOARD_END + 0) +#define IRQ_GPAIN1 (IRQ_BOARD_END + 1) +#define IRQ_GPAIN2 (IRQ_BOARD_END + 2) +#define IRQ_GPAIN3 (IRQ_BOARD_END + 3) +#define IRQ_GPBIN0 (IRQ_BOARD_END + 4) +#define IRQ_GPBIN1 (IRQ_BOARD_END + 5) +#define IRQ_GPBIN2 (IRQ_BOARD_END + 6) +#define IRQ_GPBIN3 (IRQ_BOARD_END + 7) +#define IRQ_GPBIN4 (IRQ_BOARD_END + 8) +#define IRQ_GPBIN5 (IRQ_BOARD_END + 9) +#define IRQ_GPCIN0 (IRQ_BOARD_END + 10) +#define IRQ_GPCIN1 (IRQ_BOARD_END + 11) +#define IRQ_GPCIN2 (IRQ_BOARD_END + 12) +#define IRQ_GPCIN3 (IRQ_BOARD_END + 13) +#define IRQ_GPCIN4 (IRQ_BOARD_END + 14) +#define IRQ_GPCIN5 (IRQ_BOARD_END + 15) +#define IRQ_GPCIN6 (IRQ_BOARD_END + 16) +#define IRQ_GPCIN7 (IRQ_BOARD_END + 17) +#define IRQ_MSTXINT (IRQ_BOARD_END + 18) +#define IRQ_MSRXINT (IRQ_BOARD_END + 19) +#define IRQ_MSSTOPERRINT (IRQ_BOARD_END + 20) +#define IRQ_TPTXINT (IRQ_BOARD_END + 21) +#define IRQ_TPRXINT (IRQ_BOARD_END + 22) +#define IRQ_TPSTOPERRINT (IRQ_BOARD_END + 23) +#define SSPXMTINT (IRQ_BOARD_END + 24) +#define SSPRCVINT (IRQ_BOARD_END + 25) +#define SSPROR (IRQ_BOARD_END + 26) +#define AUDXMTDMADONEA (IRQ_BOARD_END + 32) +#define AUDRCVDMADONEA (IRQ_BOARD_END + 33) +#define AUDXMTDMADONEB (IRQ_BOARD_END + 34) +#define AUDRCVDMADONEB (IRQ_BOARD_END + 35) +#define AUDTFSR (IRQ_BOARD_END + 36) +#define AUDRFSR (IRQ_BOARD_END + 37) +#define AUDTUR (IRQ_BOARD_END + 38) +#define AUDROR (IRQ_BOARD_END + 39) +#define AUDDTS (IRQ_BOARD_END + 40) +#define AUDRDD (IRQ_BOARD_END + 41) +#define AUDSTO (IRQ_BOARD_END + 42) +#define IRQ_USBPWR (IRQ_BOARD_END + 43) +#define IRQ_HCIM (IRQ_BOARD_END + 44) +#define IRQ_HCIBUFFACC (IRQ_BOARD_END + 45) +#define IRQ_HCIRMTWKP (IRQ_BOARD_END + 46) +#define IRQ_NHCIMFCIR (IRQ_BOARD_END + 47) +#define IRQ_USB_PORT_RESUME (IRQ_BOARD_END + 48) +#define IRQ_S0_READY_NINT (IRQ_BOARD_END + 49) +#define IRQ_S1_READY_NINT (IRQ_BOARD_END + 50) +#define IRQ_S0_CD_VALID (IRQ_BOARD_END + 51) +#define IRQ_S1_CD_VALID (IRQ_BOARD_END + 52) +#define IRQ_S0_BVD1_STSCHG (IRQ_BOARD_END + 53) +#define IRQ_S1_BVD1_STSCHG (IRQ_BOARD_END + 54) + +#define IRQ_LOCOMO_START (IRQ_BOARD_END) +#define IRQ_LOCOMO_KEY (IRQ_BOARD_END + 0) +#define IRQ_LOCOMO_GPIO0 (IRQ_BOARD_END + 1) +#define IRQ_LOCOMO_GPIO1 (IRQ_BOARD_END + 2) +#define IRQ_LOCOMO_GPIO2 (IRQ_BOARD_END + 3) +#define IRQ_LOCOMO_GPIO3 (IRQ_BOARD_END + 4) +#define IRQ_LOCOMO_GPIO4 (IRQ_BOARD_END + 5) +#define IRQ_LOCOMO_GPIO5 (IRQ_BOARD_END + 6) +#define IRQ_LOCOMO_GPIO6 (IRQ_BOARD_END + 7) +#define IRQ_LOCOMO_GPIO7 (IRQ_BOARD_END + 8) +#define IRQ_LOCOMO_GPIO8 (IRQ_BOARD_END + 9) +#define IRQ_LOCOMO_GPIO9 (IRQ_BOARD_END + 10) +#define IRQ_LOCOMO_GPIO10 (IRQ_BOARD_END + 11) +#define IRQ_LOCOMO_GPIO11 (IRQ_BOARD_END + 12) +#define IRQ_LOCOMO_GPIO12 (IRQ_BOARD_END + 13) +#define IRQ_LOCOMO_GPIO13 (IRQ_BOARD_END + 14) +#define IRQ_LOCOMO_GPIO14 (IRQ_BOARD_END + 15) +#define IRQ_LOCOMO_GPIO15 (IRQ_BOARD_END + 16) +#define IRQ_LOCOMO_LT (IRQ_BOARD_END + 17) +#define IRQ_LOCOMO_SPI_RFR (IRQ_BOARD_END + 18) +#define IRQ_LOCOMO_SPI_RFW (IRQ_BOARD_END + 19) +#define IRQ_LOCOMO_SPI_OVRN (IRQ_BOARD_END + 20) +#define IRQ_LOCOMO_SPI_TEND (IRQ_BOARD_END + 21) + +/* + * Figure out the MAX IRQ number. + * + * If we have an SA1111, the max IRQ is S1_BVD1_STSCHG+1. + * If we have an LoCoMo, the max IRQ is IRQ_LOCOMO_SPI_TEND+1 + * Otherwise, we have the standard IRQs only. + */ +#ifdef CONFIG_SA1111 +#define NR_IRQS (IRQ_S1_BVD1_STSCHG + 1) +#elif defined(CONFIG_SHARP_LOCOMO) +#define NR_IRQS (IRQ_LOCOMO_SPI_TEND + 1) +#elif defined(CONFIG_PXA_HAVE_BOARD_IRQS) +#define NR_IRQS (IRQ_BOARD_END) +#elif defined(CONFIG_MACH_ZYLONITE) +#define NR_IRQS (IRQ_BOARD_START + 32) +#else +#define NR_IRQS (IRQ_BOARD_START) +#endif + +/* + * Board specific IRQs. Define them here. + * Do not surround them with ifdefs. + */ +#define LUBBOCK_IRQ(x) (IRQ_BOARD_START + (x)) +#define LUBBOCK_SD_IRQ LUBBOCK_IRQ(0) +#define LUBBOCK_SA1111_IRQ LUBBOCK_IRQ(1) +#define LUBBOCK_USB_IRQ LUBBOCK_IRQ(2) /* usb connect */ +#define LUBBOCK_ETH_IRQ LUBBOCK_IRQ(3) +#define LUBBOCK_UCB1400_IRQ LUBBOCK_IRQ(4) +#define LUBBOCK_BB_IRQ LUBBOCK_IRQ(5) +#define LUBBOCK_USB_DISC_IRQ LUBBOCK_IRQ(6) /* usb disconnect */ +#define LUBBOCK_LAST_IRQ LUBBOCK_IRQ(6) + +#define LPD270_IRQ(x) (IRQ_BOARD_START + (x)) +#define LPD270_USBC_IRQ LPD270_IRQ(2) +#define LPD270_ETHERNET_IRQ LPD270_IRQ(3) +#define LPD270_AC97_IRQ LPD270_IRQ(4) + +#define MAINSTONE_IRQ(x) (IRQ_BOARD_START + (x)) +#define MAINSTONE_MMC_IRQ MAINSTONE_IRQ(0) +#define MAINSTONE_USIM_IRQ MAINSTONE_IRQ(1) +#define MAINSTONE_USBC_IRQ MAINSTONE_IRQ(2) +#define MAINSTONE_ETHERNET_IRQ MAINSTONE_IRQ(3) +#define MAINSTONE_AC97_IRQ MAINSTONE_IRQ(4) +#define MAINSTONE_PEN_IRQ MAINSTONE_IRQ(5) +#define MAINSTONE_MSINS_IRQ MAINSTONE_IRQ(6) +#define MAINSTONE_EXBRD_IRQ MAINSTONE_IRQ(7) +#define MAINSTONE_S0_CD_IRQ MAINSTONE_IRQ(9) +#define MAINSTONE_S0_STSCHG_IRQ MAINSTONE_IRQ(10) +#define MAINSTONE_S0_IRQ MAINSTONE_IRQ(11) +#define MAINSTONE_S1_CD_IRQ MAINSTONE_IRQ(13) +#define MAINSTONE_S1_STSCHG_IRQ MAINSTONE_IRQ(14) +#define MAINSTONE_S1_IRQ MAINSTONE_IRQ(15) + +/* LoCoMo Interrupts (CONFIG_SHARP_LOCOMO) */ +#define IRQ_LOCOMO_KEY_BASE (IRQ_BOARD_START + 0) +#define IRQ_LOCOMO_GPIO_BASE (IRQ_BOARD_START + 1) +#define IRQ_LOCOMO_LT_BASE (IRQ_BOARD_START + 2) +#define IRQ_LOCOMO_SPI_BASE (IRQ_BOARD_START + 3) + +/* phyCORE-PXA270 (PCM027) Interrupts */ +#define PCM027_IRQ(x) (IRQ_BOARD_START + (x)) +#define PCM027_BTDET_IRQ PCM027_IRQ(0) +#define PCM027_FF_RI_IRQ PCM027_IRQ(1) +#define PCM027_MMCDET_IRQ PCM027_IRQ(2) +#define PCM027_PM_5V_IRQ PCM027_IRQ(3) + +/* ITE8152 irqs */ +/* add IT8152 IRQs beyond BOARD_END */ +#ifdef CONFIG_PCI_HOST_ITE8152 +#define IT8152_IRQ(x) (IRQ_BOARD_END + (x)) + +/* IRQ-sources in 3 groups - local devices, LPC (serial), and external PCI */ +#define IT8152_LD_IRQ_COUNT 9 +#define IT8152_LP_IRQ_COUNT 16 +#define IT8152_PD_IRQ_COUNT 15 + +/* Priorities: */ +#define IT8152_PD_IRQ(i) IT8152_IRQ(i) +#define IT8152_LP_IRQ(i) (IT8152_IRQ(i) + IT8152_PD_IRQ_COUNT) +#define IT8152_LD_IRQ(i) (IT8152_IRQ(i) + IT8152_PD_IRQ_COUNT + IT8152_LP_IRQ_COUNT) + +#define IT8152_LAST_IRQ IT8152_LD_IRQ(IT8152_LD_IRQ_COUNT - 1) + +#if NR_IRQS < (IT8152_LAST_IRQ+1) +#undef NR_IRQS +#define NR_IRQS (IT8152_LAST_IRQ+1) +#endif + +#endif /* CONFIG_PCI_HOST_ITE8152 */ diff --git a/arch/arm/mach-pxa/include/mach/littleton.h b/arch/arm/mach-pxa/include/mach/littleton.h new file mode 100644 index 00000000000..5c4e320c143 --- /dev/null +++ b/arch/arm/mach-pxa/include/mach/littleton.h @@ -0,0 +1,8 @@ +#ifndef __ASM_ARCH_ZYLONITE_H +#define __ASM_ARCH_ZYLONITE_H + +#define LITTLETON_ETH_PHYS 0x30000000 + +#define LITTLETON_GPIO_LCD_CS (17) + +#endif /* __ASM_ARCH_ZYLONITE_H */ diff --git a/arch/arm/mach-pxa/include/mach/lpd270.h b/arch/arm/mach-pxa/include/mach/lpd270.h new file mode 100644 index 00000000000..f89fb715266 --- /dev/null +++ b/arch/arm/mach-pxa/include/mach/lpd270.h @@ -0,0 +1,38 @@ +/* + * arch/arm/mach-pxa/include/mach/lpd270.h + * + * Author: Lennert Buytenhek + * Created: Feb 10, 2006 + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ + +#ifndef __ASM_ARCH_LPD270_H +#define __ASM_ARCH_LPD270_H + +#define LPD270_CPLD_PHYS PXA_CS2_PHYS +#define LPD270_CPLD_VIRT 0xf0000000 +#define LPD270_CPLD_SIZE 0x00100000 + +#define LPD270_ETH_PHYS (PXA_CS2_PHYS + 0x01000000) + +/* CPLD registers */ +#define LPD270_CPLD_REG(x) ((unsigned long)(LPD270_CPLD_VIRT + (x))) +#define LPD270_CONTROL LPD270_CPLD_REG(0x00) +#define LPD270_PERIPHERAL0 LPD270_CPLD_REG(0x04) +#define LPD270_PERIPHERAL1 LPD270_CPLD_REG(0x08) +#define LPD270_CPLD_REVISION LPD270_CPLD_REG(0x14) +#define LPD270_EEPROM_SPI_ITF LPD270_CPLD_REG(0x20) +#define LPD270_MODE_PINS LPD270_CPLD_REG(0x24) +#define LPD270_EGPIO LPD270_CPLD_REG(0x30) +#define LPD270_INT_MASK LPD270_CPLD_REG(0x40) +#define LPD270_INT_STATUS LPD270_CPLD_REG(0x50) + +#define LPD270_INT_AC97 (1 << 4) /* AC'97 CODEC IRQ */ +#define LPD270_INT_ETHERNET (1 << 3) /* Ethernet controller IRQ */ +#define LPD270_INT_USBC (1 << 2) /* USB client cable detection IRQ */ + + +#endif diff --git a/arch/arm/mach-pxa/include/mach/lubbock.h b/arch/arm/mach-pxa/include/mach/lubbock.h new file mode 100644 index 00000000000..4cb24154a5a --- /dev/null +++ b/arch/arm/mach-pxa/include/mach/lubbock.h @@ -0,0 +1,40 @@ +/* + * arch/arm/mach-pxa/include/mach/lubbock.h + * + * Author: Nicolas Pitre + * Created: Jun 15, 2001 + * Copyright: MontaVista Software Inc. + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ + +#define LUBBOCK_ETH_PHYS PXA_CS3_PHYS + +#define LUBBOCK_FPGA_PHYS PXA_CS2_PHYS +#define LUBBOCK_FPGA_VIRT (0xf0000000) +#define LUB_P2V(x) ((x) - LUBBOCK_FPGA_PHYS + LUBBOCK_FPGA_VIRT) +#define LUB_V2P(x) ((x) - LUBBOCK_FPGA_VIRT + LUBBOCK_FPGA_PHYS) + +#ifndef __ASSEMBLY__ +# define __LUB_REG(x) (*((volatile unsigned long *)LUB_P2V(x))) +#else +# define __LUB_REG(x) LUB_P2V(x) +#endif + +/* FPGA register virtual addresses */ +#define LUB_WHOAMI __LUB_REG(LUBBOCK_FPGA_PHYS + 0x000) +#define LUB_HEXLED __LUB_REG(LUBBOCK_FPGA_PHYS + 0x010) +#define LUB_DISC_BLNK_LED __LUB_REG(LUBBOCK_FPGA_PHYS + 0x040) +#define LUB_CONF_SWITCHES __LUB_REG(LUBBOCK_FPGA_PHYS + 0x050) +#define LUB_USER_SWITCHES __LUB_REG(LUBBOCK_FPGA_PHYS + 0x060) +#define LUB_MISC_WR __LUB_REG(LUBBOCK_FPGA_PHYS + 0x080) +#define LUB_MISC_RD __LUB_REG(LUBBOCK_FPGA_PHYS + 0x090) +#define LUB_IRQ_MASK_EN __LUB_REG(LUBBOCK_FPGA_PHYS + 0x0c0) +#define LUB_IRQ_SET_CLR __LUB_REG(LUBBOCK_FPGA_PHYS + 0x0d0) +#define LUB_GP __LUB_REG(LUBBOCK_FPGA_PHYS + 0x100) + +#ifndef __ASSEMBLY__ +extern void lubbock_set_misc_wr(unsigned int mask, unsigned int set); +#endif diff --git a/arch/arm/mach-pxa/include/mach/magician.h b/arch/arm/mach-pxa/include/mach/magician.h new file mode 100644 index 00000000000..38d68d99f58 --- /dev/null +++ b/arch/arm/mach-pxa/include/mach/magician.h @@ -0,0 +1,117 @@ +/* + * GPIO and IRQ definitions for HTC Magician PDA phones + * + * Copyright (c) 2007 Philipp Zabel + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + * + */ + +#ifndef _MAGICIAN_H_ +#define _MAGICIAN_H_ + +#include <mach/irqs.h> + +/* + * PXA GPIOs + */ + +#define GPIO0_MAGICIAN_KEY_POWER 0 +#define GPIO9_MAGICIAN_UNKNOWN 9 +#define GPIO10_MAGICIAN_GSM_IRQ 10 +#define GPIO11_MAGICIAN_GSM_OUT1 11 +#define GPIO13_MAGICIAN_CPLD_IRQ 13 +#define GPIO18_MAGICIAN_UNKNOWN 18 +#define GPIO22_MAGICIAN_VIBRA_EN 22 +#define GPIO26_MAGICIAN_GSM_POWER 26 +#define GPIO27_MAGICIAN_USBC_PUEN 27 +#define GPIO30_MAGICIAN_nCHARGE_EN 30 +#define GPIO37_MAGICIAN_KEY_HANGUP 37 +#define GPIO38_MAGICIAN_KEY_CONTACTS 38 +#define GPIO40_MAGICIAN_GSM_OUT2 40 +#define GPIO48_MAGICIAN_UNKNOWN 48 +#define GPIO56_MAGICIAN_UNKNOWN 56 +#define GPIO57_MAGICIAN_CAM_RESET 57 +#define GPIO75_MAGICIAN_SAMSUNG_POWER 75 +#define GPIO83_MAGICIAN_nIR_EN 83 +#define GPIO86_MAGICIAN_GSM_RESET 86 +#define GPIO87_MAGICIAN_GSM_SELECT 87 +#define GPIO90_MAGICIAN_KEY_CALENDAR 90 +#define GPIO91_MAGICIAN_KEY_CAMERA 91 +#define GPIO93_MAGICIAN_KEY_UP 93 +#define GPIO94_MAGICIAN_KEY_DOWN 94 +#define GPIO95_MAGICIAN_KEY_LEFT 95 +#define GPIO96_MAGICIAN_KEY_RIGHT 96 +#define GPIO97_MAGICIAN_KEY_ENTER 97 +#define GPIO98_MAGICIAN_KEY_RECORD 98 +#define GPIO99_MAGICIAN_HEADPHONE_IN 99 +#define GPIO100_MAGICIAN_KEY_VOL_UP 100 +#define GPIO101_MAGICIAN_KEY_VOL_DOWN 101 +#define GPIO102_MAGICIAN_KEY_PHONE 102 +#define GPIO103_MAGICIAN_LED_KP 103 +#define GPIO104_MAGICIAN_LCD_POWER_1 104 +#define GPIO105_MAGICIAN_LCD_POWER_2 105 +#define GPIO106_MAGICIAN_LCD_POWER_3 106 +#define GPIO107_MAGICIAN_DS1WM_IRQ 107 +#define GPIO108_MAGICIAN_GSM_READY 108 +#define GPIO114_MAGICIAN_UNKNOWN 114 +#define GPIO115_MAGICIAN_nPEN_IRQ 115 +#define GPIO116_MAGICIAN_nCAM_EN 116 +#define GPIO119_MAGICIAN_UNKNOWN 119 +#define GPIO120_MAGICIAN_UNKNOWN 120 + +/* + * CPLD IRQs + */ + +#define IRQ_MAGICIAN_SD (IRQ_BOARD_START + 0) +#define IRQ_MAGICIAN_EP (IRQ_BOARD_START + 1) +#define IRQ_MAGICIAN_BT (IRQ_BOARD_START + 2) +#define IRQ_MAGICIAN_AC (IRQ_BOARD_START + 3) + +/* + * CPLD EGPIOs + */ + +#define MAGICIAN_EGPIO_BASE 0x80 /* GPIO_BOARD_START */ +#define MAGICIAN_EGPIO(reg,bit) \ + (MAGICIAN_EGPIO_BASE + 8*reg + bit) + +/* output */ + +#define EGPIO_MAGICIAN_TOPPOLY_POWER MAGICIAN_EGPIO(0, 2) +#define EGPIO_MAGICIAN_LED_POWER MAGICIAN_EGPIO(0, 5) +#define EGPIO_MAGICIAN_GSM_RESET MAGICIAN_EGPIO(0, 6) +#define EGPIO_MAGICIAN_LCD_POWER MAGICIAN_EGPIO(0, 7) +#define EGPIO_MAGICIAN_SPK_POWER MAGICIAN_EGPIO(1, 0) +#define EGPIO_MAGICIAN_EP_POWER MAGICIAN_EGPIO(1, 1) +#define EGPIO_MAGICIAN_IN_SEL0 MAGICIAN_EGPIO(1, 2) +#define EGPIO_MAGICIAN_IN_SEL1 MAGICIAN_EGPIO(1, 3) +#define EGPIO_MAGICIAN_MIC_POWER MAGICIAN_EGPIO(1, 4) +#define EGPIO_MAGICIAN_CODEC_RESET MAGICIAN_EGPIO(1, 5) +#define EGPIO_MAGICIAN_CODEC_POWER MAGICIAN_EGPIO(1, 6) +#define EGPIO_MAGICIAN_BL_POWER MAGICIAN_EGPIO(1, 7) +#define EGPIO_MAGICIAN_SD_POWER MAGICIAN_EGPIO(2, 0) +#define EGPIO_MAGICIAN_CARKIT_MIC MAGICIAN_EGPIO(2, 1) +#define EGPIO_MAGICIAN_UNKNOWN_WAVEDEV_DLL MAGICIAN_EGPIO(2, 2) +#define EGPIO_MAGICIAN_FLASH_VPP MAGICIAN_EGPIO(2, 3) +#define EGPIO_MAGICIAN_BL_POWER2 MAGICIAN_EGPIO(2, 4) +#define EGPIO_MAGICIAN_CHARGE_EN MAGICIAN_EGPIO(2, 5) +#define EGPIO_MAGICIAN_GSM_POWER MAGICIAN_EGPIO(2, 7) + +/* input */ + +#define EGPIO_MAGICIAN_CABLE_STATE_AC MAGICIAN_EGPIO(4, 0) +#define EGPIO_MAGICIAN_CABLE_STATE_USB MAGICIAN_EGPIO(4, 1) + +#define EGPIO_MAGICIAN_BOARD_ID0 MAGICIAN_EGPIO(5, 0) +#define EGPIO_MAGICIAN_BOARD_ID1 MAGICIAN_EGPIO(5, 1) +#define EGPIO_MAGICIAN_BOARD_ID2 MAGICIAN_EGPIO(5, 2) +#define EGPIO_MAGICIAN_LCD_SELECT MAGICIAN_EGPIO(5, 3) +#define EGPIO_MAGICIAN_nSD_READONLY MAGICIAN_EGPIO(5, 4) + +#define EGPIO_MAGICIAN_EP_INSERT MAGICIAN_EGPIO(6, 1) + +#endif /* _MAGICIAN_H_ */ diff --git a/arch/arm/mach-pxa/include/mach/mainstone.h b/arch/arm/mach-pxa/include/mach/mainstone.h new file mode 100644 index 00000000000..3461c4302ff --- /dev/null +++ b/arch/arm/mach-pxa/include/mach/mainstone.h @@ -0,0 +1,120 @@ +/* + * arch/arm/mach-pxa/include/mach/mainstone.h + * + * Author: Nicolas Pitre + * Created: Nov 14, 2002 + * Copyright: MontaVista Software Inc. + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ + +#ifndef ASM_ARCH_MAINSTONE_H +#define ASM_ARCH_MAINSTONE_H + +#define MST_ETH_PHYS PXA_CS4_PHYS + +#define MST_FPGA_PHYS PXA_CS2_PHYS +#define MST_FPGA_VIRT (0xf0000000) +#define MST_P2V(x) ((x) - MST_FPGA_PHYS + MST_FPGA_VIRT) +#define MST_V2P(x) ((x) - MST_FPGA_VIRT + MST_FPGA_PHYS) + +#ifndef __ASSEMBLY__ +# define __MST_REG(x) (*((volatile unsigned long *)MST_P2V(x))) +#else +# define __MST_REG(x) MST_P2V(x) +#endif + +/* board level registers in the FPGA */ + +#define MST_LEDDAT1 __MST_REG(0x08000010) +#define MST_LEDDAT2 __MST_REG(0x08000014) +#define MST_LEDCTRL __MST_REG(0x08000040) +#define MST_GPSWR __MST_REG(0x08000060) +#define MST_MSCWR1 __MST_REG(0x08000080) +#define MST_MSCWR2 __MST_REG(0x08000084) +#define MST_MSCWR3 __MST_REG(0x08000088) +#define MST_MSCRD __MST_REG(0x08000090) +#define MST_INTMSKENA __MST_REG(0x080000c0) +#define MST_INTSETCLR __MST_REG(0x080000d0) +#define MST_PCMCIA0 __MST_REG(0x080000e0) +#define MST_PCMCIA1 __MST_REG(0x080000e4) + +#define MST_MSCWR1_CAMERA_ON (1 << 15) /* Camera interface power control */ +#define MST_MSCWR1_CAMERA_SEL (1 << 14) /* Camera interface mux control */ +#define MST_MSCWR1_LCD_CTL (1 << 13) /* General-purpose LCD control */ +#define MST_MSCWR1_MS_ON (1 << 12) /* Memory Stick power control */ +#define MST_MSCWR1_MMC_ON (1 << 11) /* MultiMediaCard* power control */ +#define MST_MSCWR1_MS_SEL (1 << 10) /* SD/MS multiplexer control */ +#define MST_MSCWR1_BB_SEL (1 << 9) /* PCMCIA/Baseband multiplexer */ +#define MST_MSCWR1_BT_ON (1 << 8) /* Bluetooth UART transceiver */ +#define MST_MSCWR1_BTDTR (1 << 7) /* Bluetooth UART DTR */ + +#define MST_MSCWR1_IRDA_MASK (3 << 5) /* IrDA transceiver mode */ +#define MST_MSCWR1_IRDA_FULL (0 << 5) /* full distance power */ +#define MST_MSCWR1_IRDA_OFF (1 << 5) /* shutdown */ +#define MST_MSCWR1_IRDA_MED (2 << 5) /* 2/3 distance power */ +#define MST_MSCWR1_IRDA_LOW (3 << 5) /* 1/3 distance power */ + +#define MST_MSCWR1_IRDA_FIR (1 << 4) /* IrDA transceiver SIR/FIR */ +#define MST_MSCWR1_GREENLED (1 << 3) /* LED D1 control */ +#define MST_MSCWR1_PDC_CTL (1 << 2) /* reserved */ +#define MST_MSCWR1_MTR_ON (1 << 1) /* Silent alert motor */ +#define MST_MSCWR1_SYSRESET (1 << 0) /* System reset */ + +#define MST_MSCWR2_USB_OTG_RST (1 << 6) /* USB On The Go reset */ +#define MST_MSCWR2_USB_OTG_SEL (1 << 5) /* USB On The Go control */ +#define MST_MSCWR2_nUSBC_SC (1 << 4) /* USB client soft connect control */ +#define MST_MSCWR2_I2S_SPKROFF (1 << 3) /* I2S CODEC amplifier control */ +#define MST_MSCWR2_AC97_SPKROFF (1 << 2) /* AC97 CODEC amplifier control */ +#define MST_MSCWR2_RADIO_PWR (1 << 1) /* Radio module power control */ +#define MST_MSCWR2_RADIO_WAKE (1 << 0) /* Radio module wake-up signal */ + +#define MST_MSCWR3_GPIO_RESET_EN (1 << 2) /* Enable GPIO Reset */ +#define MST_MSCWR3_GPIO_RESET (1 << 1) /* Initiate a GPIO Reset */ +#define MST_MSCWR3_COMMS_SW_RESET (1 << 0) /* Communications Processor Reset Control */ + +#define MST_MSCRD_nPENIRQ (1 << 9) /* ADI7873* nPENIRQ signal */ +#define MST_MSCRD_nMEMSTK_CD (1 << 8) /* Memory Stick detection signal */ +#define MST_MSCRD_nMMC_CD (1 << 7) /* SD/MMC card detection signal */ +#define MST_MSCRD_nUSIM_CD (1 << 6) /* USIM card detection signal */ +#define MST_MSCRD_USB_CBL (1 << 5) /* USB client cable status */ +#define MST_MSCRD_TS_BUSY (1 << 4) /* ADI7873 busy */ +#define MST_MSCRD_BTDSR (1 << 3) /* Bluetooth UART DSR */ +#define MST_MSCRD_BTRI (1 << 2) /* Bluetooth UART Ring Indicator */ +#define MST_MSCRD_BTDCD (1 << 1) /* Bluetooth UART DCD */ +#define MST_MSCRD_nMMC_WP (1 << 0) /* SD/MMC write-protect status */ + +#define MST_INT_S1_IRQ (1 << 15) /* PCMCIA socket 1 IRQ */ +#define MST_INT_S1_STSCHG (1 << 14) /* PCMCIA socket 1 status changed */ +#define MST_INT_S1_CD (1 << 13) /* PCMCIA socket 1 card detection */ +#define MST_INT_S0_IRQ (1 << 11) /* PCMCIA socket 0 IRQ */ +#define MST_INT_S0_STSCHG (1 << 10) /* PCMCIA socket 0 status changed */ +#define MST_INT_S0_CD (1 << 9) /* PCMCIA socket 0 card detection */ +#define MST_INT_nEXBRD_INT (1 << 7) /* Expansion board IRQ */ +#define MST_INT_MSINS (1 << 6) /* Memory Stick* detection */ +#define MST_INT_PENIRQ (1 << 5) /* ADI7873* touch-screen IRQ */ +#define MST_INT_AC97 (1 << 4) /* AC'97 CODEC IRQ */ +#define MST_INT_ETHERNET (1 << 3) /* Ethernet controller IRQ */ +#define MST_INT_USBC (1 << 2) /* USB client cable detection IRQ */ +#define MST_INT_USIM (1 << 1) /* USIM card detection IRQ */ +#define MST_INT_MMC (1 << 0) /* MMC/SD card detection IRQ */ + +#define MST_PCMCIA_nIRQ (1 << 10) /* IRQ / ready signal */ +#define MST_PCMCIA_nSPKR_BVD2 (1 << 9) /* VDD sense / digital speaker */ +#define MST_PCMCIA_nSTSCHG_BVD1 (1 << 8) /* VDD sense / card status changed */ +#define MST_PCMCIA_nVS2 (1 << 7) /* VSS voltage sense */ +#define MST_PCMCIA_nVS1 (1 << 6) /* VSS voltage sense */ +#define MST_PCMCIA_nCD (1 << 5) /* Card detection signal */ +#define MST_PCMCIA_RESET (1 << 4) /* Card reset signal */ +#define MST_PCMCIA_PWR_MASK (0x000f) /* MAX1602 power-supply controls */ + +#define MST_PCMCIA_PWR_VPP_0 0x0 /* voltage VPP = 0V */ +#define MST_PCMCIA_PWR_VPP_120 0x2 /* voltage VPP = 12V*/ +#define MST_PCMCIA_PWR_VPP_VCC 0x1 /* voltage VPP = VCC */ +#define MST_PCMCIA_PWR_VCC_0 0x0 /* voltage VCC = 0V */ +#define MST_PCMCIA_PWR_VCC_33 0x8 /* voltage VCC = 3.3V */ +#define MST_PCMCIA_PWR_VCC_50 0x4 /* voltage VCC = 5.0V */ + +#endif diff --git a/arch/arm/mach-pxa/include/mach/memory.h b/arch/arm/mach-pxa/include/mach/memory.h new file mode 100644 index 00000000000..59aef89808d --- /dev/null +++ b/arch/arm/mach-pxa/include/mach/memory.h @@ -0,0 +1,52 @@ +/* + * arch/arm/mach-pxa/include/mach/memory.h + * + * Author: Nicolas Pitre + * Copyright: (C) 2001 MontaVista Software Inc. + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ + +#ifndef __ASM_ARCH_MEMORY_H +#define __ASM_ARCH_MEMORY_H + +/* + * Physical DRAM offset. + */ +#define PHYS_OFFSET UL(0xa0000000) + +/* + * Virtual view <-> DMA view memory address translations + * virt_to_bus: Used to translate the virtual address to an + * address suitable to be passed to set_dma_addr + * bus_to_virt: Used to convert an address for DMA operations + * to an address that the kernel can use. + */ +#define __virt_to_bus(x) __virt_to_phys(x) +#define __bus_to_virt(x) __phys_to_virt(x) + +/* + * The nodes are matched with the physical SDRAM banks as follows: + * + * node 0: 0xa0000000-0xa3ffffff --> 0xc0000000-0xc3ffffff + * node 1: 0xa4000000-0xa7ffffff --> 0xc4000000-0xc7ffffff + * node 2: 0xa8000000-0xabffffff --> 0xc8000000-0xcbffffff + * node 3: 0xac000000-0xafffffff --> 0xcc000000-0xcfffffff + * + * This needs a node mem size of 26 bits. + */ +#define NODE_MEM_SIZE_BITS 26 + +#if !defined(__ASSEMBLY__) && defined(CONFIG_MACH_ARMCORE) && defined(CONFIG_PCI) +void cmx2xx_pci_adjust_zones(int node, unsigned long *size, + unsigned long *holes); + +#define arch_adjust_zones(node, size, holes) \ + cmx2xx_pci_adjust_zones(node, size, holes) + +#define ISA_DMA_THRESHOLD (PHYS_OFFSET + SZ_64M - 1) +#endif + +#endif diff --git a/arch/arm/mach-pxa/include/mach/mfp-pxa25x.h b/arch/arm/mach-pxa/include/mach/mfp-pxa25x.h new file mode 100644 index 00000000000..617cab2cc8d --- /dev/null +++ b/arch/arm/mach-pxa/include/mach/mfp-pxa25x.h @@ -0,0 +1,161 @@ +#ifndef __ASM_ARCH_MFP_PXA25X_H +#define __ASM_ARCH_MFP_PXA25X_H + +#include <mach/mfp.h> +#include <mach/mfp-pxa2xx.h> + +/* GPIO */ +#define GPIO2_GPIO MFP_CFG_IN(GPIO2, AF0) +#define GPIO3_GPIO MFP_CFG_IN(GPIO3, AF0) +#define GPIO4_GPIO MFP_CFG_IN(GPIO4, AF0) +#define GPIO5_GPIO MFP_CFG_IN(GPIO5, AF0) +#define GPIO6_GPIO MFP_CFG_IN(GPIO6, AF0) +#define GPIO7_GPIO MFP_CFG_IN(GPIO7, AF0) +#define GPIO8_GPIO MFP_CFG_IN(GPIO8, AF0) + +#define GPIO1_RST MFP_CFG_IN(GPIO1, AF1) + +/* Crystal and Clock Signals */ +#define GPIO10_RTCCLK MFP_CFG_OUT(GPIO10, AF1, DRIVE_LOW) +#define GPIO70_RTCCLK MFP_CFG_OUT(GPIO70, AF1, DRIVE_LOW) +#define GPIO7_48MHz MFP_CFG_OUT(GPIO7, AF1, DRIVE_LOW) +#define GPIO11_3_6MHz MFP_CFG_OUT(GPIO11, AF1, DRIVE_LOW) +#define GPIO71_3_6MHz MFP_CFG_OUT(GPIO71, AF1, DRIVE_LOW) +#define GPIO12_32KHz MFP_CFG_OUT(GPIO12, AF1, DRIVE_LOW) +#define GPIO72_32kHz MFP_CFG_OUT(GPIO72, AF1, DRIVE_LOW) + +/* SDRAM and Static Memory I/O Signals */ +#define GPIO15_nCS_1 MFP_CFG_OUT(GPIO15, AF2, DRIVE_HIGH) +#define GPIO78_nCS_2 MFP_CFG_OUT(GPIO78, AF2, DRIVE_HIGH) +#define GPIO79_nCS_3 MFP_CFG_OUT(GPIO79, AF2, DRIVE_HIGH) +#define GPIO80_nCS_4 MFP_CFG_OUT(GPIO80, AF2, DRIVE_HIGH) +#define GPIO33_nCS_5 MFP_CFG_OUT(GPIO33, AF2, DRIVE_HIGH) + +/* Miscellaneous I/O and DMA Signals */ +#define GPIO18_RDY MFP_CFG_IN(GPIO18, AF1) +#define GPIO20_DREQ_0 MFP_CFG_IN(GPIO20, AF1) +#define GPIO19_DREQ_1 MFP_CFG_IN(GPIO19, AF1) + +/* Alternate Bus Master Mode I/O Signals */ +#define GPIO13_MBGNT MFP_CFG_OUT(GPIO13, AF2, DRIVE_LOW) +#define GPIO73_MBGNT MFP_CFG_OUT(GPIO73, AF1, DRIVE_LOW) +#define GPIO14_MBREQ MFP_CFG_IN(GPIO14, AF1) +#define GPIO66_MBREQ MFP_CFG_IN(GPIO66, AF1) + +/* PC CARD */ +#define GPIO52_nPCE_1 MFP_CFG_OUT(GPIO52, AF2, DRIVE_HIGH) +#define GPIO53_nPCE_2 MFP_CFG_OUT(GPIO53, AF2, DRIVE_HIGH) +#define GPIO55_nPREG MFP_CFG_OUT(GPIO55, AF2, DRIVE_HIGH) +#define GPIO50_nPIOR MFP_CFG_OUT(GPIO50, AF2, DRIVE_HIGH) +#define GPIO51_nPIOW MFP_CFG_OUT(GPIO51, AF2, DRIVE_HIGH) +#define GPIO49_nPWE MFP_CFG_OUT(GPIO49, AF2, DRIVE_HIGH) +#define GPIO48_nPOE MFP_CFG_OUT(GPIO48, AF2, DRIVE_HIGH) +#define GPIO57_nIOIS16 MFP_CFG_IN(GPIO57, AF1) +#define GPIO56_nPWAIT MFP_CFG_IN(GPIO56, AF1) +#define GPIO54_nPSKTSEL MFP_CFG_OUT(GPIO54, AF2, DRIVE_HIGH) + +/* FFUART */ +#define GPIO34_FFUART_RXD MFP_CFG_IN(GPIO34, AF1) +#define GPIO35_FFUART_CTS MFP_CFG_IN(GPIO35, AF1) +#define GPIO36_FFUART_DCD MFP_CFG_IN(GPIO36, AF1) +#define GPIO37_FFUART_DSR MFP_CFG_IN(GPIO37, AF1) +#define GPIO38_FFUART_RI MFP_CFG_IN(GPIO38, AF1) +#define GPIO39_FFUART_TXD MFP_CFG_OUT(GPIO39, AF2, DRIVE_HIGH) +#define GPIO40_FFUART_DTR MFP_CFG_OUT(GPIO40, AF2, DRIVE_HIGH) +#define GPIO41_FFUART_RTS MFP_CFG_OUT(GPIO41, AF2, DRIVE_HIGH) + +/* BTUART */ +#define GPIO42_BTUART_RXD MFP_CFG_IN(GPIO42, AF1) +#define GPIO43_BTUART_TXD MFP_CFG_OUT(GPIO43, AF2, DRIVE_HIGH) +#define GPIO44_BTUART_CTS MFP_CFG_IN(GPIO44, AF1) +#define GPIO45_BTUART_RTS MFP_CFG_OUT(GPIO45, AF2, DRIVE_HIGH) + +/* STUART */ +#define GPIO46_STUART_RXD MFP_CFG_IN(GPIO46, AF2) +#define GPIO47_STUART_TXD MFP_CFG_OUT(GPIO47, AF1, DRIVE_HIGH) + +/* HWUART */ +#define GPIO42_HWUART_RXD MFP_CFG_IN(GPIO42, AF3) +#define GPIO43_HWUART_TXD MFP_CFG_OUT(GPIO43, AF3, DRIVE_HIGH) +#define GPIO44_HWUART_CTS MFP_CFG_IN(GPIO44, AF3) +#define GPIO45_HWUART_RTS MFP_CFG_OUT(GPIO45, AF3, DRIVE_HIGH) +#define GPIO48_HWUART_TXD MFP_CFG_OUT(GPIO48, AF1, DRIVE_HIGH) +#define GPIO49_HWUART_RXD MFP_CFG_IN(GPIO49, AF1) +#define GPIO50_HWUART_CTS MFP_CFG_IN(GPIO50, AF1) +#define GPIO51_HWUART_RTS MFP_CFG_OUT(GPIO51, AF1, DRIVE_HIGH) + +/* FICP */ +#define GPIO46_FICP_RXD MFP_CFG_IN(GPIO46, AF1) +#define GPIO47_FICP_TXD MFP_CFG_OUT(GPIO47, AF2, DRIVE_HIGH) + +/* PWM 0/1 */ +#define GPIO16_PWM0_OUT MFP_CFG_OUT(GPIO16, AF2, DRIVE_LOW) +#define GPIO17_PWM1_OUT MFP_CFG_OUT(GPIO17, AF2, DRIVE_LOW) + +/* AC97 */ +#define GPIO28_AC97_BITCLK MFP_CFG_IN(GPIO28, AF1) +#define GPIO29_AC97_SDATA_IN_0 MFP_CFG_IN(GPIO29, AF1) +#define GPIO30_AC97_SDATA_OUT MFP_CFG_OUT(GPIO30, AF2, DRIVE_LOW) +#define GPIO31_AC97_SYNC MFP_CFG_OUT(GPIO31, AF2, DRIVE_LOW) +#define GPIO32_AC97_SDATA_IN_1 MFP_CFG_IN(GPIO32, AF1) + +/* I2S */ +#define GPIO28_I2S_BITCLK_IN MFP_CFG_IN(GPIO28, AF2) +#define GPIO28_I2S_BITCLK_OUT MFP_CFG_OUT(GPIO28, AF1, DRIVE_LOW) +#define GPIO29_I2S_SDATA_IN MFP_CFG_IN(GPIO29, AF2) +#define GPIO30_I2S_SDATA_OUT MFP_CFG_OUT(GPIO30, AF1, DRIVE_LOW) +#define GPIO31_I2S_SYNC MFP_CFG_OUT(GPIO31, AF1, DRIVE_LOW) +#define GPIO32_I2S_SYSCLK MFP_CFG_OUT(GPIO32, AF1, DRIVE_LOW) + +/* SSP 1 */ +#define GPIO23_SSP1_SCLK MFP_CFG_OUT(GPIO23, AF2, DRIVE_LOW) +#define GPIO24_SSP1_SFRM MFP_CFG_OUT(GPIO24, AF2, DRIVE_LOW) +#define GPIO25_SSP1_TXD MFP_CFG_OUT(GPIO25, AF2, DRIVE_LOW) +#define GPIO26_SSP1_RXD MFP_CFG_IN(GPIO26, AF1) +#define GPIO27_SSP1_EXTCLK MFP_CFG_IN(GPIO27, AF1) + +/* SSP 2 - NSSP */ +#define GPIO81_SSP2_CLK_OUT MFP_CFG_OUT(GPIO81, AF1, DRIVE_LOW) +#define GPIO81_SSP2_CLK_IN MFP_CFG_IN(GPIO81, AF1) +#define GPIO82_SSP2_FRM_OUT MFP_CFG_OUT(GPIO82, AF1, DRIVE_LOW) +#define GPIO82_SSP2_FRM_IN MFP_CFG_IN(GPIO82, AF1) +#define GPIO83_SSP2_TXD MFP_CFG_OUT(GPIO83, AF1, DRIVE_LOW) +#define GPIO83_SSP2_RXD MFP_CFG_IN(GPIO83, AF2) +#define GPIO84_SSP2_TXD MFP_CFG_OUT(GPIO84, AF1, DRIVE_LOW) +#define GPIO84_SSP2_RXD MFP_CFG_IN(GPIO84, AF2) + +/* MMC */ +#define GPIO6_MMC_CLK MFP_CFG_OUT(GPIO6, AF1, DRIVE_LOW) +#define GPIO8_MMC_CS0 MFP_CFG_OUT(GPIO8, AF1, DRIVE_LOW) +#define GPIO9_MMC_CS1 MFP_CFG_OUT(GPIO9, AF1, DRIVE_LOW) +#define GPIO34_MMC_CS0 MFP_CFG_OUT(GPIO34, AF2, DRIVE_LOW) +#define GPIO39_MMC_CS1 MFP_CFG_OUT(GPIO39, AF1, DRIVE_LOW) +#define GPIO53_MMC_CLK MFP_CFG_OUT(GPIO53, AF1, DRIVE_LOW) +#define GPIO54_MMC_CLK MFP_CFG_OUT(GPIO54, AF1, DRIVE_LOW) +#define GPIO69_MMC_CLK MFP_CFG_OUT(GPIO69, AF1, DRIVE_LOW) +#define GPIO67_MMC_CS0 MFP_CFG_OUT(GPIO67, AF1, DRIVE_LOW) +#define GPIO68_MMC_CS1 MFP_CFG_OUT(GPIO68, AF1, DRIVE_LOW) + +/* LCD */ +#define GPIO58_LCD_LDD_0 MFP_CFG_OUT(GPIO58, AF2, DRIVE_LOW) +#define GPIO59_LCD_LDD_1 MFP_CFG_OUT(GPIO59, AF2, DRIVE_LOW) +#define GPIO60_LCD_LDD_2 MFP_CFG_OUT(GPIO60, AF2, DRIVE_LOW) +#define GPIO61_LCD_LDD_3 MFP_CFG_OUT(GPIO61, AF2, DRIVE_LOW) +#define GPIO62_LCD_LDD_4 MFP_CFG_OUT(GPIO62, AF2, DRIVE_LOW) +#define GPIO63_LCD_LDD_5 MFP_CFG_OUT(GPIO63, AF2, DRIVE_LOW) +#define GPIO64_LCD_LDD_6 MFP_CFG_OUT(GPIO64, AF2, DRIVE_LOW) +#define GPIO65_LCD_LDD_7 MFP_CFG_OUT(GPIO65, AF2, DRIVE_LOW) +#define GPIO66_LCD_LDD_8 MFP_CFG_OUT(GPIO66, AF2, DRIVE_LOW) +#define GPIO67_LCD_LDD_9 MFP_CFG_OUT(GPIO67, AF2, DRIVE_LOW) +#define GPIO68_LCD_LDD_10 MFP_CFG_OUT(GPIO68, AF2, DRIVE_LOW) +#define GPIO69_LCD_LDD_11 MFP_CFG_OUT(GPIO69, AF2, DRIVE_LOW) +#define GPIO70_LCD_LDD_12 MFP_CFG_OUT(GPIO70, AF2, DRIVE_LOW) +#define GPIO71_LCD_LDD_13 MFP_CFG_OUT(GPIO71, AF2, DRIVE_LOW) +#define GPIO72_LCD_LDD_14 MFP_CFG_OUT(GPIO72, AF2, DRIVE_LOW) +#define GPIO73_LCD_LDD_15 MFP_CFG_OUT(GPIO73, AF2, DRIVE_LOW) +#define GPIO74_LCD_FCLK MFP_CFG_OUT(GPIO74, AF2, DRIVE_LOW) +#define GPIO75_LCD_LCLK MFP_CFG_OUT(GPIO75, AF2, DRIVE_LOW) +#define GPIO76_LCD_PCLK MFP_CFG_OUT(GPIO76, AF2, DRIVE_LOW) +#define GPIO77_LCD_BIAS MFP_CFG_OUT(GPIO77, AF2, DRIVE_LOW) + +#endif /* __ASM_ARCH_MFP_PXA25X_H */ diff --git a/arch/arm/mach-pxa/include/mach/mfp-pxa27x.h b/arch/arm/mach-pxa/include/mach/mfp-pxa27x.h new file mode 100644 index 00000000000..122bdbd5318 --- /dev/null +++ b/arch/arm/mach-pxa/include/mach/mfp-pxa27x.h @@ -0,0 +1,433 @@ +#ifndef __ASM_ARCH_MFP_PXA27X_H +#define __ASM_ARCH_MFP_PXA27X_H + +/* + * NOTE: for those special-function bidirectional GPIOs, as described + * in the "PXA27x Developer's Manual" Section 24.4.2.1, only its input + * alternative is preserved, the direction is actually selected by the + * specific controller, and this should work in most cases. + */ + +#include <mach/mfp.h> +#include <mach/mfp-pxa2xx.h> + +/* GPIO */ +#define GPIO85_GPIO MFP_CFG_IN(GPIO85, AF0) +#define GPIO86_GPIO MFP_CFG_IN(GPIO86, AF0) +#define GPIO87_GPIO MFP_CFG_IN(GPIO87, AF0) +#define GPIO88_GPIO MFP_CFG_IN(GPIO88, AF0) +#define GPIO89_GPIO MFP_CFG_IN(GPIO89, AF0) +#define GPIO90_GPIO MFP_CFG_IN(GPIO90, AF0) +#define GPIO91_GPIO MFP_CFG_IN(GPIO91, AF0) +#define GPIO92_GPIO MFP_CFG_IN(GPIO92, AF0) +#define GPIO93_GPIO MFP_CFG_IN(GPIO93, AF0) +#define GPIO94_GPIO MFP_CFG_IN(GPIO94, AF0) +#define GPIO95_GPIO MFP_CFG_IN(GPIO95, AF0) +#define GPIO96_GPIO MFP_CFG_IN(GPIO96, AF0) +#define GPIO97_GPIO MFP_CFG_IN(GPIO97, AF0) +#define GPIO98_GPIO MFP_CFG_IN(GPIO98, AF0) +#define GPIO99_GPIO MFP_CFG_IN(GPIO99, AF0) +#define GPIO100_GPIO MFP_CFG_IN(GPIO100, AF0) +#define GPIO101_GPIO MFP_CFG_IN(GPIO101, AF0) +#define GPIO102_GPIO MFP_CFG_IN(GPIO102, AF0) +#define GPIO103_GPIO MFP_CFG_IN(GPIO103, AF0) +#define GPIO104_GPIO MFP_CFG_IN(GPIO104, AF0) +#define GPIO105_GPIO MFP_CFG_IN(GPIO105, AF0) +#define GPIO106_GPIO MFP_CFG_IN(GPIO106, AF0) +#define GPIO107_GPIO MFP_CFG_IN(GPIO107, AF0) +#define GPIO108_GPIO MFP_CFG_IN(GPIO108, AF0) +#define GPIO109_GPIO MFP_CFG_IN(GPIO109, AF0) +#define GPIO110_GPIO MFP_CFG_IN(GPIO110, AF0) +#define GPIO111_GPIO MFP_CFG_IN(GPIO111, AF0) +#define GPIO112_GPIO MFP_CFG_IN(GPIO112, AF0) +#define GPIO113_GPIO MFP_CFG_IN(GPIO113, AF0) +#define GPIO114_GPIO MFP_CFG_IN(GPIO114, AF0) +#define GPIO115_GPIO MFP_CFG_IN(GPIO115, AF0) +#define GPIO116_GPIO MFP_CFG_IN(GPIO116, AF0) +#define GPIO117_GPIO MFP_CFG_IN(GPIO117, AF0) +#define GPIO118_GPIO MFP_CFG_IN(GPIO118, AF0) +#define GPIO119_GPIO MFP_CFG_IN(GPIO119, AF0) +#define GPIO120_GPIO MFP_CFG_IN(GPIO120, AF0) + +/* Crystal and Clock Signals */ +#define GPIO9_HZ_CLK MFP_CFG_OUT(GPIO9, AF1, DRIVE_LOW) +#define GPIO10_HZ_CLK MFP_CFG_OUT(GPIO10, AF1, DRIVE_LOW) +#define GPIO11_48_MHz MFP_CFG_OUT(GPIO11, AF3, DRIVE_LOW) +#define GPIO12_48_MHz MFP_CFG_OUT(GPIO12, AF3, DRIVE_LOW) +#define GPIO13_CLK_EXT MFP_CFG_IN(GPIO13, AF1) + +/* OS Timer Signals */ +#define GPIO11_EXT_SYNC_0 MFP_CFG_IN(GPIO11, AF1) +#define GPIO12_EXT_SYNC_1 MFP_CFG_IN(GPIO12, AF1) +#define GPIO9_CHOUT_0 MFP_CFG_OUT(GPIO9, AF3, DRIVE_LOW) +#define GPIO10_CHOUT_1 MFP_CFG_OUT(GPIO10, AF3, DRIVE_LOW) +#define GPIO11_CHOUT_0 MFP_CFG_OUT(GPIO11, AF1, DRIVE_LOW) +#define GPIO12_CHOUT_1 MFP_CFG_OUT(GPIO12, AF1, DRIVE_LOW) + +/* SDRAM and Static Memory I/O Signals */ +#define GPIO20_nSDCS_2 MFP_CFG_OUT(GPIO20, AF1, DRIVE_HIGH) +#define GPIO21_nSDCS_3 MFP_CFG_OUT(GPIO21, AF1, DRIVE_HIGH) +#define GPIO15_nCS_1 MFP_CFG_OUT(GPIO15, AF2, DRIVE_HIGH) +#define GPIO78_nCS_2 MFP_CFG_OUT(GPIO78, AF2, DRIVE_HIGH) +#define GPIO79_nCS_3 MFP_CFG_OUT(GPIO79, AF2, DRIVE_HIGH) +#define GPIO80_nCS_4 MFP_CFG_OUT(GPIO80, AF2, DRIVE_HIGH) +#define GPIO33_nCS_5 MFP_CFG_OUT(GPIO33, AF2, DRIVE_HIGH) + +/* Miscellaneous I/O and DMA Signals */ +#define GPIO21_DVAL_0 MFP_CFG_OUT(GPIO21, AF2, DRIVE_HIGH) +#define GPIO116_DVAL_0 MFP_CFG_OUT(GPIO116, AF1, DRIVE_HIGH) +#define GPIO33_DVAL_1 MFP_CFG_OUT(GPIO33, AF1, DRIVE_HIGH) +#define GPIO96_DVAL_1 MFP_CFG_OUT(GPIO96, AF2, DRIVE_HIGH) +#define GPIO18_RDY MFP_CFG_IN(GPIO18, AF1) +#define GPIO20_DREQ_0 MFP_CFG_IN(GPIO20, AF1) +#define GPIO115_DREQ_0 MFP_CFG_IN(GPIO115, AF1) +#define GPIO80_DREQ_1 MFP_CFG_IN(GPIO80, AF1) +#define GPIO97_DREQ_1 MFP_CFG_IN(GPIO97, AF2) +#define GPIO85_DREQ_2 MFP_CFG_IN(GPIO85, AF2) +#define GPIO100_DREQ_2 MFP_CFG_IN(GPIO100, AF2) + +/* Alternate Bus Master Mode I/O Signals */ +#define GPIO20_MBREQ MFP_CFG_IN(GPIO20, AF2) +#define GPIO80_MBREQ MFP_CFG_IN(GPIO80, AF2) +#define GPIO96_MBREQ MFP_CFG_IN(GPIO96, AF2) +#define GPIO115_MBREQ MFP_CFG_IN(GPIO115, AF3) +#define GPIO21_MBGNT MFP_CFG_OUT(GPIO21, AF3, DRIVE_LOW) +#define GPIO33_MBGNT MFP_CFG_OUT(GPIO33, AF3, DRIVE_LOW) +#define GPIO97_MBGNT MFP_CFG_OUT(GPIO97, AF2, DRIVE_LOW) +#define GPIO116_MBGNT MFP_CFG_OUT(GPIO116, AF3, DRIVE_LOW) + +/* PC CARD */ +#define GPIO15_nPCE_1 MFP_CFG_OUT(GPIO15, AF1, DRIVE_HIGH) +#define GPIO85_nPCE_1 MFP_CFG_OUT(GPIO85, AF1, DRIVE_HIGH) +#define GPIO86_nPCE_1 MFP_CFG_OUT(GPIO86, AF1, DRIVE_HIGH) +#define GPIO102_nPCE_1 MFP_CFG_OUT(GPIO102, AF1, DRIVE_HIGH) +#define GPIO54_nPCE_2 MFP_CFG_OUT(GPIO54, AF2, DRIVE_HIGH) +#define GPIO78_nPCE_2 MFP_CFG_OUT(GPIO78, AF1, DRIVE_HIGH) +#define GPIO87_nPCE_2 MFP_CFG_IN(GPIO87, AF1) +#define GPIO55_nPREG MFP_CFG_OUT(GPIO55, AF2, DRIVE_HIGH) +#define GPIO50_nPIOR MFP_CFG_OUT(GPIO50, AF2, DRIVE_HIGH) +#define GPIO51_nPIOW MFP_CFG_OUT(GPIO51, AF2, DRIVE_HIGH) +#define GPIO49_nPWE MFP_CFG_OUT(GPIO49, AF2, DRIVE_HIGH) +#define GPIO48_nPOE MFP_CFG_OUT(GPIO48, AF2, DRIVE_HIGH) +#define GPIO57_nIOIS16 MFP_CFG_IN(GPIO57, AF1) +#define GPIO56_nPWAIT MFP_CFG_IN(GPIO56, AF1) +#define GPIO79_PSKTSEL MFP_CFG_OUT(GPIO79, AF1, DRIVE_HIGH) +#define GPIO104_PSKTSEL MFP_CFG_OUT(GPIO104, AF1, DRIVE_HIGH) + +/* I2C */ +#define GPIO117_I2C_SCL MFP_CFG_IN(GPIO117, AF1) +#define GPIO118_I2C_SDA MFP_CFG_IN(GPIO118, AF1) + +/* FFUART */ +#define GPIO9_FFUART_CTS MFP_CFG_IN(GPIO9, AF3) +#define GPIO26_FFUART_CTS MFP_CFG_IN(GPIO26, AF3) +#define GPIO35_FFUART_CTS MFP_CFG_IN(GPIO35, AF1) +#define GPIO100_FFUART_CTS MFP_CFG_IN(GPIO100, AF3) +#define GPIO10_FFUART_DCD MFP_CFG_IN(GPIO10, AF1) +#define GPIO36_FFUART_DCD MFP_CFG_IN(GPIO36, AF1) +#define GPIO33_FFUART_DSR MFP_CFG_IN(GPIO33, AF2) +#define GPIO37_FFUART_DSR MFP_CFG_IN(GPIO37, AF1) +#define GPIO38_FFUART_RI MFP_CFG_IN(GPIO38, AF1) +#define GPIO89_FFUART_RI MFP_CFG_IN(GPIO89, AF3) +#define GPIO19_FFUART_RXD MFP_CFG_IN(GPIO19, AF3) +#define GPIO33_FFUART_RXD MFP_CFG_IN(GPIO33, AF1) +#define GPIO34_FFUART_RXD MFP_CFG_IN(GPIO34, AF1) +#define GPIO41_FFUART_RXD MFP_CFG_IN(GPIO41, AF1) +#define GPIO53_FFUART_RXD MFP_CFG_IN(GPIO53, AF1) +#define GPIO85_FFUART_RXD MFP_CFG_IN(GPIO85, AF1) +#define GPIO96_FFUART_RXD MFP_CFG_IN(GPIO96, AF3) +#define GPIO102_FFUART_RXD MFP_CFG_IN(GPIO102, AF3) +#define GPIO16_FFUART_TXD MFP_CFG_OUT(GPIO16, AF3, DRIVE_HIGH) +#define GPIO37_FFUART_TXD MFP_CFG_OUT(GPIO37, AF3, DRIVE_HIGH) +#define GPIO39_FFUART_TXD MFP_CFG_OUT(GPIO39, AF2, DRIVE_HIGH) +#define GPIO83_FFUART_TXD MFP_CFG_OUT(GPIO83, AF2, DRIVE_HIGH) +#define GPIO99_FFUART_TXD MFP_CFG_OUT(GPIO99, AF3, DRIVE_HIGH) +#define GPIO27_FFUART_RTS MFP_CFG_OUT(GPIO27, AF3, DRIVE_HIGH) +#define GPIO41_FFUART_RTS MFP_CFG_OUT(GPIO41, AF2, DRIVE_HIGH) +#define GPIO83_FFUART_RTS MFP_CFG_OUT(GPIO83, AF3, DRIVE_HIGH) +#define GPIO98_FFUART_RTS MFP_CFG_OUT(GPIO98, AF3, DRIVE_HIGH) +#define GPIO40_FFUART_DTR MFP_CFG_OUT(GPIO40, AF2, DRIVE_HIGH) +#define GPIO82_FFUART_DTR MFP_CFG_OUT(GPIO82, AF3, DRIVE_HIGH) + +/* BTUART */ +#define GPIO44_BTUART_CTS MFP_CFG_IN(GPIO44, AF1) +#define GPIO42_BTUART_RXD MFP_CFG_IN(GPIO42, AF1) +#define GPIO45_BTUART_RTS MFP_CFG_OUT(GPIO45, AF2, DRIVE_HIGH) +#define GPIO43_BTUART_TXD MFP_CFG_OUT(GPIO43, AF2, DRIVE_HIGH) + +/* STUART */ +#define GPIO46_STUART_RXD MFP_CFG_IN(GPIO46, AF2) +#define GPIO47_STUART_TXD MFP_CFG_OUT(GPIO47, AF1, DRIVE_HIGH) + +/* FICP */ +#define GPIO42_FICP_RXD MFP_CFG_IN(GPIO42, AF2) +#define GPIO46_FICP_RXD MFP_CFG_IN(GPIO46, AF1) +#define GPIO43_FICP_TXD MFP_CFG_OUT(GPIO43, AF1, DRIVE_HIGH) +#define GPIO47_FICP_TXD MFP_CFG_OUT(GPIO47, AF2, DRIVE_HIGH) + +/* PWM 0/1/2/3 */ +#define GPIO11_PWM2_OUT MFP_CFG_OUT(GPIO11, AF2, DRIVE_LOW) +#define GPIO12_PWM3_OUT MFP_CFG_OUT(GPIO12, AF2, DRIVE_LOW) +#define GPIO16_PWM0_OUT MFP_CFG_OUT(GPIO16, AF2, DRIVE_LOW) +#define GPIO17_PWM1_OUT MFP_CFG_OUT(GPIO17, AF2, DRIVE_LOW) +#define GPIO38_PWM1_OUT MFP_CFG_OUT(GPIO38, AF3, DRIVE_LOW) +#define GPIO46_PWM2_OUT MFP_CFG_OUT(GPIO46, AF2, DRIVE_LOW) +#define GPIO47_PWM3_OUT MFP_CFG_OUT(GPIO47, AF3, DRIVE_LOW) +#define GPIO79_PWM2_OUT MFP_CFG_OUT(GPIO79, AF3, DRIVE_LOW) +#define GPIO80_PWM3_OUT MFP_CFG_OUT(GPIO80, AF3, DRIVE_LOW) +#define GPIO115_PWM1_OUT MFP_CFG_OUT(GPIO115, AF3, DRIVE_LOW) + +/* AC97 */ +#define GPIO31_AC97_SYNC MFP_CFG_OUT(GPIO31, AF2, DRIVE_LOW) +#define GPIO94_AC97_SYNC MFP_CFG_OUT(GPIO94, AF1, DRIVE_LOW) +#define GPIO30_AC97_SDATA_OUT MFP_CFG_OUT(GPIO30, AF2, DRIVE_LOW) +#define GPIO93_AC97_SDATA_OUT MFP_CFG_OUT(GPIO93, AF1, DRIVE_LOW) +#define GPIO45_AC97_SYSCLK MFP_CFG_OUT(GPIO45, AF1, DRIVE_LOW) +#define GPIO89_AC97_SYSCLK MFP_CFG_OUT(GPIO89, AF1, DRIVE_LOW) +#define GPIO98_AC97_SYSCLK MFP_CFG_OUT(GPIO98, AF1, DRIVE_LOW) +#define GPIO95_AC97_nRESET MFP_CFG_OUT(GPIO95, AF1, DRIVE_LOW) +#define GPIO113_AC97_nRESET MFP_CFG_OUT(GPIO113, AF2, DRIVE_LOW) +#define GPIO28_AC97_BITCLK MFP_CFG_IN(GPIO28, AF1) +#define GPIO29_AC97_SDATA_IN_0 MFP_CFG_IN(GPIO29, AF1) +#define GPIO116_AC97_SDATA_IN_0 MFP_CFG_IN(GPIO116, AF2) +#define GPIO99_AC97_SDATA_IN_1 MFP_CFG_IN(GPIO99, AF2) + +/* I2S */ +#define GPIO28_I2S_BITCLK_IN MFP_CFG_IN(GPIO28, AF2) +#define GPIO28_I2S_BITCLK_OUT MFP_CFG_OUT(GPIO28, AF1, DRIVE_LOW) +#define GPIO29_I2S_SDATA_IN MFP_CFG_IN(GPIO29, AF2) +#define GPIO30_I2S_SDATA_OUT MFP_CFG_OUT(GPIO30, AF1, DRIVE_LOW) +#define GPIO31_I2S_SYNC MFP_CFG_OUT(GPIO31, AF1, DRIVE_LOW) +#define GPIO113_I2S_SYSCLK MFP_CFG_OUT(GPIO113, AF1, DRIVE_LOW) + +/* SSP 1 */ +#define GPIO23_SSP1_SCLK MFP_CFG_OUT(GPIO23, AF2, DRIVE_LOW) +#define GPIO29_SSP1_SCLK MFP_CFG_IN(GPIO29, AF3) +#define GPIO27_SSP1_SYSCLK MFP_CFG_OUT(GPIO27, AF1, DRIVE_LOW) +#define GPIO53_SSP1_SYSCLK MFP_CFG_OUT(GPIO53, AF3, DRIVE_LOW) +#define GPIO24_SSP1_SFRM MFP_CFG_IN(GPIO24, AF2) +#define GPIO28_SSP1_SFRM MFP_CFG_IN(GPIO28, AF3) +#define GPIO25_SSP1_TXD MFP_CFG_OUT(GPIO25, AF2, DRIVE_LOW) +#define GPIO57_SSP1_TXD MFP_CFG_OUT(GPIO57, AF3, DRIVE_LOW) +#define GPIO26_SSP1_RXD MFP_CFG_IN(GPIO26, AF1) +#define GPIO27_SSP1_SCLKEN MFP_CFG_IN(GPIO27, AF2) + +/* SSP 2 */ +#define GPIO19_SSP2_SCLK MFP_CFG_IN(GPIO19, AF1) +#define GPIO22_SSP2_SCLK MFP_CFG_IN(GPIO22, AF3) +#define GPIO29_SSP2_SCLK MFP_CFG_OUT(GPIO29, AF3, DRIVE_LOW) +#define GPIO36_SSP2_SCLK MFP_CFG_IN(GPIO36, AF2) +#define GPIO50_SSP2_SCLK MFP_CFG_IN(GPIO50, AF3) +#define GPIO22_SSP2_SYSCLK MFP_CFG_OUT(GPIO22, AF2, DRIVE_LOW) +#define GPIO14_SSP2_SFRM MFP_CFG_IN(GPIO14, AF2) +#define GPIO37_SSP2_SFRM MFP_CFG_IN(GPIO37, AF2) +#define GPIO87_SSP2_SFRM MFP_CFG_OUT(GPIO87, AF3, DRIVE_LOW) +#define GPIO88_SSP2_SFRM MFP_CFG_IN(GPIO88, AF3) +#define GPIO13_SSP2_TXD MFP_CFG_OUT(GPIO13, AF1, DRIVE_LOW) +#define GPIO38_SSP2_TXD MFP_CFG_OUT(GPIO38, AF2, DRIVE_LOW) +#define GPIO87_SSP2_TXD MFP_CFG_OUT(GPIO87, AF1, DRIVE_LOW) +#define GPIO89_SSP2_TXD MFP_CFG_OUT(GPIO89, AF3, DRIVE_LOW) +#define GPIO11_SSP2_RXD MFP_CFG_IN(GPIO11, AF2) +#define GPIO29_SSP2_RXD MFP_CFG_OUT(GPIO29, AF1, DRIVE_LOW) +#define GPIO40_SSP2_RXD MFP_CFG_IN(GPIO40, AF1) +#define GPIO86_SSP2_RXD MFP_CFG_IN(GPIO86, AF1) +#define GPIO88_SSP2_RXD MFP_CFG_IN(GPIO88, AF2) +#define GPIO22_SSP2_EXTCLK MFP_CFG_IN(GPIO22, AF1) +#define GPIO27_SSP2_EXTCLK MFP_CFG_IN(GPIO27, AF1) +#define GPIO22_SSP2_SCLKEN MFP_CFG_IN(GPIO22, AF2) +#define GPIO23_SSP2_SCLKEN MFP_CFG_IN(GPIO23, AF2) + +/* SSP 3 */ +#define GPIO34_SSP3_SCLK MFP_CFG_IN(GPIO34, AF3) +#define GPIO40_SSP3_SCLK MFP_CFG_OUT(GPIO40, AF3, DRIVE_LOW) +#define GPIO52_SSP3_SCLK MFP_CFG_IN(GPIO52, AF2) +#define GPIO84_SSP3_SCLK MFP_CFG_IN(GPIO84, AF1) +#define GPIO45_SSP3_SYSCLK MFP_CFG_OUT(GPIO45, AF3, DRIVE_LOW) +#define GPIO35_SSP3_SFRM MFP_CFG_IN(GPIO35, AF3) +#define GPIO39_SSP3_SFRM MFP_CFG_IN(GPIO39, AF3) +#define GPIO83_SSP3_SFRM MFP_CFG_IN(GPIO83, AF1) +#define GPIO35_SSP3_TXD MFP_CFG_OUT(GPIO35, AF3, DRIVE_LOW) +#define GPIO38_SSP3_TXD MFP_CFG_OUT(GPIO38, AF1, DRIVE_LOW) +#define GPIO81_SSP3_TXD MFP_CFG_OUT(GPIO81, AF1, DRIVE_LOW) +#define GPIO41_SSP3_RXD MFP_CFG_IN(GPIO41, AF3) +#define GPIO82_SSP3_RXD MFP_CFG_IN(GPIO82, AF1) +#define GPIO89_SSP3_RXD MFP_CFG_IN(GPIO89, AF1) + +/* MMC */ +#define GPIO32_MMC_CLK MFP_CFG_OUT(GPIO32, AF2, DRIVE_LOW) +#define GPIO92_MMC_DAT_0 MFP_CFG_IN(GPIO92, AF1) +#define GPIO109_MMC_DAT_1 MFP_CFG_IN(GPIO109, AF1) +#define GPIO110_MMC_DAT_2 MFP_CFG_IN(GPIO110, AF1) +#define GPIO111_MMC_DAT_3 MFP_CFG_IN(GPIO111, AF1) +#define GPIO112_MMC_CMD MFP_CFG_IN(GPIO112, AF1) + +/* LCD */ +#define GPIO58_LCD_LDD_0 MFP_CFG_OUT(GPIO58, AF2, DRIVE_LOW) +#define GPIO59_LCD_LDD_1 MFP_CFG_OUT(GPIO59, AF2, DRIVE_LOW) +#define GPIO60_LCD_LDD_2 MFP_CFG_OUT(GPIO60, AF2, DRIVE_LOW) +#define GPIO61_LCD_LDD_3 MFP_CFG_OUT(GPIO61, AF2, DRIVE_LOW) +#define GPIO62_LCD_LDD_4 MFP_CFG_OUT(GPIO62, AF2, DRIVE_LOW) +#define GPIO63_LCD_LDD_5 MFP_CFG_OUT(GPIO63, AF2, DRIVE_LOW) +#define GPIO64_LCD_LDD_6 MFP_CFG_OUT(GPIO64, AF2, DRIVE_LOW) +#define GPIO65_LCD_LDD_7 MFP_CFG_OUT(GPIO65, AF2, DRIVE_LOW) +#define GPIO66_LCD_LDD_8 MFP_CFG_OUT(GPIO66, AF2, DRIVE_LOW) +#define GPIO67_LCD_LDD_9 MFP_CFG_OUT(GPIO67, AF2, DRIVE_LOW) +#define GPIO68_LCD_LDD_10 MFP_CFG_OUT(GPIO68, AF2, DRIVE_LOW) +#define GPIO69_LCD_LDD_11 MFP_CFG_OUT(GPIO69, AF2, DRIVE_LOW) +#define GPIO70_LCD_LDD_12 MFP_CFG_OUT(GPIO70, AF2, DRIVE_LOW) +#define GPIO71_LCD_LDD_13 MFP_CFG_OUT(GPIO71, AF2, DRIVE_LOW) +#define GPIO72_LCD_LDD_14 MFP_CFG_OUT(GPIO72, AF2, DRIVE_LOW) +#define GPIO73_LCD_LDD_15 MFP_CFG_OUT(GPIO73, AF2, DRIVE_LOW) +#define GPIO86_LCD_LDD_16 MFP_CFG_OUT(GPIO86, AF2, DRIVE_LOW) +#define GPIO87_LCD_LDD_17 MFP_CFG_OUT(GPIO87, AF2, DRIVE_LOW) +#define GPIO74_LCD_FCLK MFP_CFG_OUT(GPIO74, AF2, DRIVE_LOW) +#define GPIO75_LCD_LCLK MFP_CFG_OUT(GPIO75, AF2, DRIVE_LOW) +#define GPIO76_LCD_PCLK MFP_CFG_OUT(GPIO76, AF2, DRIVE_LOW) +#define GPIO77_LCD_BIAS MFP_CFG_OUT(GPIO77, AF2, DRIVE_LOW) +#define GPIO14_LCD_VSYNC MFP_CFG_IN(GPIO14, AF1) +#define GPIO19_LCD_CS MFP_CFG_OUT(GPIO19, AF2, DRIVE_LOW) + +/* Keypad */ +#define GPIO93_KP_DKIN_0 MFP_CFG_IN(GPIO93, AF1) +#define GPIO94_KP_DKIN_1 MFP_CFG_IN(GPIO94, AF1) +#define GPIO95_KP_DKIN_2 MFP_CFG_IN(GPIO95, AF1) +#define GPIO96_KP_DKIN_3 MFP_CFG_IN(GPIO96, AF1) +#define GPIO97_KP_DKIN_4 MFP_CFG_IN(GPIO97, AF1) +#define GPIO98_KP_DKIN_5 MFP_CFG_IN(GPIO98, AF1) +#define GPIO99_KP_DKIN_6 MFP_CFG_IN(GPIO99, AF1) +#define GPIO13_KP_KDIN_7 MFP_CFG_IN(GPIO13, AF2) +#define GPIO100_KP_MKIN_0 MFP_CFG_IN(GPIO100, AF1) +#define GPIO101_KP_MKIN_1 MFP_CFG_IN(GPIO101, AF1) +#define GPIO102_KP_MKIN_2 MFP_CFG_IN(GPIO102, AF1) +#define GPIO34_KP_MKIN_3 MFP_CFG_IN(GPIO34, AF2) +#define GPIO37_KP_MKIN_3 MFP_CFG_IN(GPIO37, AF3) +#define GPIO97_KP_MKIN_3 MFP_CFG_IN(GPIO97, AF3) +#define GPIO98_KP_MKIN_4 MFP_CFG_IN(GPIO98, AF3) +#define GPIO38_KP_MKIN_4 MFP_CFG_IN(GPIO38, AF2) +#define GPIO39_KP_MKIN_4 MFP_CFG_IN(GPIO39, AF1) +#define GPIO16_KP_MKIN_5 MFP_CFG_IN(GPIO16, AF1) +#define GPIO90_KP_MKIN_5 MFP_CFG_IN(GPIO90, AF1) +#define GPIO99_KP_MKIN_5 MFP_CFG_IN(GPIO99, AF3) +#define GPIO17_KP_MKIN_6 MFP_CFG_IN(GPIO17, AF1) +#define GPIO91_KP_MKIN_6 MFP_CFG_IN(GPIO91, AF1) +#define GPIO95_KP_MKIN_6 MFP_CFG_IN(GPIO95, AF3) +#define GPIO13_KP_MKIN_7 MFP_CFG_IN(GPIO13, AF3) +#define GPIO36_KP_MKIN_7 MFP_CFG_IN(GPIO36, AF3) +#define GPIO103_KP_MKOUT_0 MFP_CFG_OUT(GPIO103, AF2, DRIVE_HIGH) +#define GPIO104_KP_MKOUT_1 MFP_CFG_OUT(GPIO104, AF2, DRIVE_HIGH) +#define GPIO105_KP_MKOUT_2 MFP_CFG_OUT(GPIO105, AF2, DRIVE_HIGH) +#define GPIO106_KP_MKOUT_3 MFP_CFG_OUT(GPIO106, AF2, DRIVE_HIGH) +#define GPIO107_KP_MKOUT_4 MFP_CFG_OUT(GPIO107, AF2, DRIVE_HIGH) +#define GPIO108_KP_MKOUT_5 MFP_CFG_OUT(GPIO108, AF2, DRIVE_HIGH) +#define GPIO35_KP_MKOUT_6 MFP_CFG_OUT(GPIO35, AF2, DRIVE_HIGH) +#define GPIO22_KP_MKOUT_7 MFP_CFG_OUT(GPIO22, AF1, DRIVE_HIGH) +#define GPIO40_KP_MKOUT_6 MFP_CFG_OUT(GPIO40, AF1, DRIVE_HIGH) +#define GPIO41_KP_MKOUT_7 MFP_CFG_OUT(GPIO41, AF1, DRIVE_HIGH) +#define GPIO96_KP_MKOUT_6 MFP_CFG_OUT(GPIO96, AF3, DRIVE_HIGH) + +/* USB P3 */ +#define GPIO10_USB_P3_5 MFP_CFG_IN(GPIO10, AF3) +#define GPIO11_USB_P3_1 MFP_CFG_IN(GPIO11, AF3) +#define GPIO30_USB_P3_2 MFP_CFG_OUT(GPIO30, AF3, DRIVE_LOW) +#define GPIO31_USB_P3_6 MFP_CFG_OUT(GPIO31, AF3, DRIVE_LOW) +#define GPIO56_USB_P3_4 MFP_CFG_OUT(GPIO56, AF1, DRIVE_LOW) +#define GPIO86_USB_P3_5 MFP_CFG_IN(GPIO86, AF3) +#define GPIO87_USB_P3_1 MFP_CFG_IN(GPIO87, AF3) +#define GPIO90_USB_P3_5 MFP_CFG_IN(GPIO90, AF2) +#define GPIO91_USB_P3_1 MFP_CFG_IN(GPIO91, AF2) +#define GPIO113_USB_P3_3 MFP_CFG_IN(GPIO113, AF3) + +/* USB P2 */ +#define GPIO34_USB_P2_2 MFP_CFG_OUT(GPIO34, AF1, DRIVE_LOW) +#define GPIO35_USB_P2_1 MFP_CFG_IN(GPIO35, AF2) +#define GPIO36_USB_P2_4 MFP_CFG_OUT(GPIO36, AF1, DRIVE_LOW) +#define GPIO37_USB_P2_8 MFP_CFG_OUT(GPIO37, AF1, DRIVE_LOW) +#define GPIO38_USB_P2_3 MFP_CFG_IN(GPIO38, AF3) +#define GPIO39_USB_P2_6 MFP_CFG_OUT(GPIO39, AF1, DRIVE_LOW) +#define GPIO40_USB_P2_5 MFP_CFG_IN(GPIO40, AF3) +#define GPIO41_USB_P2_7 MFP_CFG_IN(GPIO41, AF2) +#define GPIO53_USB_P2_3 MFP_CFG_IN(GPIO53, AF2) + +/* USB Host Port 1/2 */ +#define GPIO88_USBH1_PWR MFP_CFG_IN(GPIO88, AF1) +#define GPIO89_USBH1_PEN MFP_CFG_OUT(GPIO89, AF2, DRIVE_LOW) +#define GPIO119_USBH2_PWR MFP_CFG_IN(GPIO119, AF1) +#define GPIO120_USBH2_PEN MFP_CFG_OUT(GPIO120, AF2, DRIVE_LOW) + +/* QCI - default to Master Mode: CIF_FV/CIF_LV Direction In */ +#define GPIO115_CIF_DD_3 MFP_CFG_IN(GPIO115, AF2) +#define GPIO116_CIF_DD_2 MFP_CFG_IN(GPIO116, AF1) +#define GPIO12_CIF_DD_7 MFP_CFG_IN(GPIO12, AF2) +#define GPIO17_CIF_DD_6 MFP_CFG_IN(GPIO17, AF2) +#define GPIO23_CIF_MCLK MFP_CFG_OUT(GPIO23, AF1, DRIVE_LOW) +#define GPIO24_CIF_FV MFP_CFG_IN(GPIO24, AF1) +#define GPIO25_CIF_LV MFP_CFG_IN(GPIO25, AF1) +#define GPIO26_CIF_PCLK MFP_CFG_IN(GPIO26, AF2) +#define GPIO27_CIF_DD_0 MFP_CFG_IN(GPIO27, AF3) +#define GPIO42_CIF_MCLK MFP_CFG_OUT(GPIO42, AF3, DRIVE_LOW) +#define GPIO43_CIF_FV MFP_CFG_IN(GPIO43, AF3) +#define GPIO44_CIF_LV MFP_CFG_IN(GPIO44, AF3) +#define GPIO45_CIF_PCLK MFP_CFG_IN(GPIO45, AF3) +#define GPIO47_CIF_DD_0 MFP_CFG_IN(GPIO47, AF1) +#define GPIO48_CIF_DD_5 MFP_CFG_IN(GPIO48, AF1) +#define GPIO50_CIF_DD_3 MFP_CFG_IN(GPIO50, AF1) +#define GPIO51_CIF_DD_2 MFP_CFG_IN(GPIO51, AF1) +#define GPIO52_CIF_DD_4 MFP_CFG_IN(GPIO52, AF1) +#define GPIO53_CIF_MCLK MFP_CFG_OUT(GPIO53, AF2, DRIVE_LOW) +#define GPIO54_CIF_PCLK MFP_CFG_IN(GPIO54, AF3) +#define GPIO55_CIF_DD_1 MFP_CFG_IN(GPIO55, AF1) +#define GPIO81_CIF_DD_0 MFP_CFG_IN(GPIO81, AF2) +#define GPIO82_CIF_DD_5 MFP_CFG_IN(GPIO82, AF3) +#define GPIO83_CIF_DD_4 MFP_CFG_IN(GPIO83, AF3) +#define GPIO84_CIF_FV MFP_CFG_IN(GPIO84, AF3) +#define GPIO85_CIF_LV MFP_CFG_IN(GPIO85, AF3) +#define GPIO90_CIF_DD_4 MFP_CFG_IN(GPIO90, AF3) +#define GPIO91_CIF_DD_5 MFP_CFG_IN(GPIO91, AF3) +#define GPIO93_CIF_DD_6 MFP_CFG_IN(GPIO93, AF2) +#define GPIO94_CIF_DD_5 MFP_CFG_IN(GPIO94, AF2) +#define GPIO95_CIF_DD_4 MFP_CFG_IN(GPIO95, AF2) +#define GPIO98_CIF_DD_0 MFP_CFG_IN(GPIO98, AF2) +#define GPIO103_CIF_DD_3 MFP_CFG_IN(GPIO103, AF1) +#define GPIO104_CIF_DD_2 MFP_CFG_IN(GPIO104, AF1) +#define GPIO105_CIF_DD_1 MFP_CFG_IN(GPIO105, AF1) +#define GPIO106_CIF_DD_9 MFP_CFG_IN(GPIO106, AF1) +#define GPIO107_CIF_DD_8 MFP_CFG_IN(GPIO107, AF1) +#define GPIO108_CIF_DD_7 MFP_CFG_IN(GPIO108, AF1) +#define GPIO114_CIF_DD_1 MFP_CFG_IN(GPIO114, AF1) + +/* Universal Subscriber ID Interface */ +#define GPIO114_UVS0 MFP_CFG_OUT(GPIO114, AF2, DRIVE_LOW) +#define GPIO115_nUVS1 MFP_CFG_OUT(GPIO115, AF2, DRIVE_LOW) +#define GPIO116_nUVS2 MFP_CFG_OUT(GPIO116, AF2, DRIVE_LOW) +#define GPIO14_UCLK MFP_CFG_OUT(GPIO14, AF3, DRIVE_LOW) +#define GPIO91_UCLK MFP_CFG_OUT(GPIO91, AF2, DRIVE_LOW) +#define GPIO19_nURST MFP_CFG_OUT(GPIO19, AF3, DRIVE_LOW) +#define GPIO90_nURST MFP_CFG_OUT(GPIO90, AF2, DRIVE_LOW) +#define GPIO116_UDET MFP_CFG_IN(GPIO116, AF3) +#define GPIO114_UEN MFP_CFG_OUT(GPIO114, AF1, DRIVE_LOW) +#define GPIO115_UEN MFP_CFG_OUT(GPIO115, AF1, DRIVE_LOW) + +/* Mobile Scalable Link (MSL) Interface */ +#define GPIO81_BB_OB_DAT_0 MFP_CFG_OUT(GPIO81, AF2, DRIVE_LOW) +#define GPIO48_BB_OB_DAT_1 MFP_CFG_OUT(GPIO48, AF1, DRIVE_LOW) +#define GPIO50_BB_OB_DAT_2 MFP_CFG_OUT(GPIO50, AF1, DRIVE_LOW) +#define GPIO51_BB_OB_DAT_3 MFP_CFG_OUT(GPIO51, AF1, DRIVE_LOW) +#define GPIO52_BB_OB_CLK MFP_CFG_OUT(GPIO52, AF1, DRIVE_LOW) +#define GPIO53_BB_OB_STB MFP_CFG_OUT(GPIO53, AF1, DRIVE_LOW) +#define GPIO54_BB_OB_WAIT MFP_CFG_IN(GPIO54, AF2) +#define GPIO82_BB_IB_DAT_0 MFP_CFG_IN(GPIO82, AF2) +#define GPIO55_BB_IB_DAT_1 MFP_CFG_IN(GPIO55, AF2) +#define GPIO56_BB_IB_DAT_2 MFP_CFG_IN(GPIO56, AF2) +#define GPIO57_BB_IB_DAT_3 MFP_CFG_IN(GPIO57, AF2) +#define GPIO83_BB_IB_CLK MFP_CFG_IN(GPIO83, AF2) +#define GPIO84_BB_IB_STB MFP_CFG_IN(GPIO84, AF2) +#define GPIO85_BB_IB_WAIT MFP_CFG_OUT(GPIO85, AF2, DRIVE_LOW) + +/* Memory Stick Host Controller */ +#define GPIO92_MSBS MFP_CFG_OUT(GPIO92, AF2, DRIVE_LOW) +#define GPIO109_MSSDIO MFP_CFG_IN(GPIO109, AF2) +#define GPIO112_nMSINS MFP_CFG_IN(GPIO112, AF2) +#define GPIO32_MSSCLK MFP_CFG_OUT(GPIO32, AF1, DRIVE_LOW) + +extern int keypad_set_wake(unsigned int on); +#endif /* __ASM_ARCH_MFP_PXA27X_H */ diff --git a/arch/arm/mach-pxa/include/mach/mfp-pxa2xx.h b/arch/arm/mach-pxa/include/mach/mfp-pxa2xx.h new file mode 100644 index 00000000000..3e9211591e2 --- /dev/null +++ b/arch/arm/mach-pxa/include/mach/mfp-pxa2xx.h @@ -0,0 +1,133 @@ +#ifndef __ASM_ARCH_MFP_PXA2XX_H +#define __ASM_ARCH_MFP_PXA2XX_H + +#include <mach/mfp.h> + +/* + * the following MFP_xxx bit definitions in mfp.h are re-used for pxa2xx: + * + * MFP_PIN(x) + * MFP_AFx + * MFP_LPM_DRIVE_{LOW, HIGH} + * MFP_LPM_EDGE_x + * + * other MFP_x bit definitions will be ignored + * + * and adds the below two bits specifically for pxa2xx: + * + * bit 23 - Input/Output (PXA2xx specific) + * bit 24 - Wakeup Enable(PXA2xx specific) + */ + +#define MFP_DIR_IN (0x0 << 23) +#define MFP_DIR_OUT (0x1 << 23) +#define MFP_DIR_MASK (0x1 << 23) +#define MFP_DIR(x) (((x) >> 23) & 0x1) + +#define MFP_LPM_CAN_WAKEUP (0x1 << 24) +#define WAKEUP_ON_EDGE_RISE (MFP_LPM_CAN_WAKEUP | MFP_LPM_EDGE_RISE) +#define WAKEUP_ON_EDGE_FALL (MFP_LPM_CAN_WAKEUP | MFP_LPM_EDGE_FALL) +#define WAKEUP_ON_EDGE_BOTH (MFP_LPM_CAN_WAKEUP | MFP_LPM_EDGE_BOTH) + +/* specifically for enabling wakeup on keypad GPIOs */ +#define WAKEUP_ON_LEVEL_HIGH (MFP_LPM_CAN_WAKEUP) + +#define MFP_CFG_IN(pin, af) \ + ((MFP_CFG_DEFAULT & ~(MFP_AF_MASK | MFP_DIR_MASK)) |\ + (MFP_PIN(MFP_PIN_##pin) | MFP_##af | MFP_DIR_IN)) + +/* NOTE: pins configured as output _must_ provide a low power state, + * and this state should help to minimize the power dissipation. + */ +#define MFP_CFG_OUT(pin, af, state) \ + ((MFP_CFG_DEFAULT & ~(MFP_AF_MASK | MFP_DIR_MASK | MFP_LPM_STATE_MASK)) |\ + (MFP_PIN(MFP_PIN_##pin) | MFP_##af | MFP_DIR_OUT | MFP_LPM_##state)) + +/* Common configurations for pxa25x and pxa27x + * + * Note: pins configured as GPIO are always initialized to input + * so not to cause any side effect + */ +#define GPIO0_GPIO MFP_CFG_IN(GPIO0, AF0) +#define GPIO1_GPIO MFP_CFG_IN(GPIO1, AF0) +#define GPIO9_GPIO MFP_CFG_IN(GPIO9, AF0) +#define GPIO10_GPIO MFP_CFG_IN(GPIO10, AF0) +#define GPIO11_GPIO MFP_CFG_IN(GPIO11, AF0) +#define GPIO12_GPIO MFP_CFG_IN(GPIO12, AF0) +#define GPIO13_GPIO MFP_CFG_IN(GPIO13, AF0) +#define GPIO14_GPIO MFP_CFG_IN(GPIO14, AF0) +#define GPIO15_GPIO MFP_CFG_IN(GPIO15, AF0) +#define GPIO16_GPIO MFP_CFG_IN(GPIO16, AF0) +#define GPIO17_GPIO MFP_CFG_IN(GPIO17, AF0) +#define GPIO18_GPIO MFP_CFG_IN(GPIO18, AF0) +#define GPIO19_GPIO MFP_CFG_IN(GPIO19, AF0) +#define GPIO20_GPIO MFP_CFG_IN(GPIO20, AF0) +#define GPIO21_GPIO MFP_CFG_IN(GPIO21, AF0) +#define GPIO22_GPIO MFP_CFG_IN(GPIO22, AF0) +#define GPIO23_GPIO MFP_CFG_IN(GPIO23, AF0) +#define GPIO24_GPIO MFP_CFG_IN(GPIO24, AF0) +#define GPIO25_GPIO MFP_CFG_IN(GPIO25, AF0) +#define GPIO26_GPIO MFP_CFG_IN(GPIO26, AF0) +#define GPIO27_GPIO MFP_CFG_IN(GPIO27, AF0) +#define GPIO28_GPIO MFP_CFG_IN(GPIO28, AF0) +#define GPIO29_GPIO MFP_CFG_IN(GPIO29, AF0) +#define GPIO30_GPIO MFP_CFG_IN(GPIO30, AF0) +#define GPIO31_GPIO MFP_CFG_IN(GPIO31, AF0) +#define GPIO32_GPIO MFP_CFG_IN(GPIO32, AF0) +#define GPIO33_GPIO MFP_CFG_IN(GPIO33, AF0) +#define GPIO34_GPIO MFP_CFG_IN(GPIO34, AF0) +#define GPIO35_GPIO MFP_CFG_IN(GPIO35, AF0) +#define GPIO36_GPIO MFP_CFG_IN(GPIO36, AF0) +#define GPIO37_GPIO MFP_CFG_IN(GPIO37, AF0) +#define GPIO38_GPIO MFP_CFG_IN(GPIO38, AF0) +#define GPIO39_GPIO MFP_CFG_IN(GPIO39, AF0) +#define GPIO40_GPIO MFP_CFG_IN(GPIO40, AF0) +#define GPIO41_GPIO MFP_CFG_IN(GPIO41, AF0) +#define GPIO42_GPIO MFP_CFG_IN(GPIO42, AF0) +#define GPIO43_GPIO MFP_CFG_IN(GPIO43, AF0) +#define GPIO44_GPIO MFP_CFG_IN(GPIO44, AF0) +#define GPIO45_GPIO MFP_CFG_IN(GPIO45, AF0) +#define GPIO46_GPIO MFP_CFG_IN(GPIO46, AF0) +#define GPIO47_GPIO MFP_CFG_IN(GPIO47, AF0) +#define GPIO48_GPIO MFP_CFG_IN(GPIO48, AF0) +#define GPIO49_GPIO MFP_CFG_IN(GPIO49, AF0) +#define GPIO50_GPIO MFP_CFG_IN(GPIO50, AF0) +#define GPIO51_GPIO MFP_CFG_IN(GPIO51, AF0) +#define GPIO52_GPIO MFP_CFG_IN(GPIO52, AF0) +#define GPIO53_GPIO MFP_CFG_IN(GPIO53, AF0) +#define GPIO54_GPIO MFP_CFG_IN(GPIO54, AF0) +#define GPIO55_GPIO MFP_CFG_IN(GPIO55, AF0) +#define GPIO56_GPIO MFP_CFG_IN(GPIO56, AF0) +#define GPIO57_GPIO MFP_CFG_IN(GPIO57, AF0) +#define GPIO58_GPIO MFP_CFG_IN(GPIO58, AF0) +#define GPIO59_GPIO MFP_CFG_IN(GPIO59, AF0) +#define GPIO60_GPIO MFP_CFG_IN(GPIO60, AF0) +#define GPIO61_GPIO MFP_CFG_IN(GPIO61, AF0) +#define GPIO62_GPIO MFP_CFG_IN(GPIO62, AF0) +#define GPIO63_GPIO MFP_CFG_IN(GPIO63, AF0) +#define GPIO64_GPIO MFP_CFG_IN(GPIO64, AF0) +#define GPIO65_GPIO MFP_CFG_IN(GPIO65, AF0) +#define GPIO66_GPIO MFP_CFG_IN(GPIO66, AF0) +#define GPIO67_GPIO MFP_CFG_IN(GPIO67, AF0) +#define GPIO68_GPIO MFP_CFG_IN(GPIO68, AF0) +#define GPIO69_GPIO MFP_CFG_IN(GPIO69, AF0) +#define GPIO70_GPIO MFP_CFG_IN(GPIO70, AF0) +#define GPIO71_GPIO MFP_CFG_IN(GPIO71, AF0) +#define GPIO72_GPIO MFP_CFG_IN(GPIO72, AF0) +#define GPIO73_GPIO MFP_CFG_IN(GPIO73, AF0) +#define GPIO74_GPIO MFP_CFG_IN(GPIO74, AF0) +#define GPIO75_GPIO MFP_CFG_IN(GPIO75, AF0) +#define GPIO76_GPIO MFP_CFG_IN(GPIO76, AF0) +#define GPIO77_GPIO MFP_CFG_IN(GPIO77, AF0) +#define GPIO78_GPIO MFP_CFG_IN(GPIO78, AF0) +#define GPIO79_GPIO MFP_CFG_IN(GPIO79, AF0) +#define GPIO80_GPIO MFP_CFG_IN(GPIO80, AF0) +#define GPIO81_GPIO MFP_CFG_IN(GPIO81, AF0) +#define GPIO82_GPIO MFP_CFG_IN(GPIO82, AF0) +#define GPIO83_GPIO MFP_CFG_IN(GPIO83, AF0) +#define GPIO84_GPIO MFP_CFG_IN(GPIO84, AF0) + +extern void pxa2xx_mfp_config(unsigned long *mfp_cfgs, int num); +extern void pxa2xx_mfp_set_lpm(int mfp, unsigned long lpm); +extern int gpio_set_wake(unsigned int gpio, unsigned int on); +#endif /* __ASM_ARCH_MFP_PXA2XX_H */ diff --git a/arch/arm/mach-pxa/include/mach/mfp-pxa300.h b/arch/arm/mach-pxa/include/mach/mfp-pxa300.h new file mode 100644 index 00000000000..bc1fb33a6e7 --- /dev/null +++ b/arch/arm/mach-pxa/include/mach/mfp-pxa300.h @@ -0,0 +1,575 @@ +/* + * arch/arm/mach-pxa/include/mach/mfp-pxa300.h + * + * PXA300/PXA310 specific MFP configuration definitions + * + * Copyright (C) 2007 Marvell International Ltd. + * 2007-08-21: eric miao <eric.miao@marvell.com> + * initial version + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ + +#ifndef __ASM_ARCH_MFP_PXA300_H +#define __ASM_ARCH_MFP_PXA300_H + +#include <mach/mfp.h> +#include <mach/mfp-pxa3xx.h> + +/* GPIO */ +#define GPIO46_GPIO MFP_CFG(GPIO46, AF1) +#define GPIO49_GPIO MFP_CFG(GPIO49, AF3) +#define GPIO50_GPIO MFP_CFG(GPIO50, AF2) +#define GPIO51_GPIO MFP_CFG(GPIO51, AF3) +#define GPIO52_GPIO MFP_CFG(GPIO52, AF3) +#define GPIO56_GPIO MFP_CFG(GPIO56, AF0) +#define GPIO58_GPIO MFP_CFG(GPIO58, AF0) +#define GPIO59_GPIO MFP_CFG(GPIO59, AF0) +#define GPIO60_GPIO MFP_CFG(GPIO60, AF0) +#define GPIO61_GPIO MFP_CFG(GPIO61, AF0) +#define GPIO62_GPIO MFP_CFG(GPIO62, AF0) + +#ifdef CONFIG_CPU_PXA310 +#define GPIO7_2_GPIO MFP_CFG(GPIO7_2, AF0) +#define GPIO8_2_GPIO MFP_CFG(GPIO8_2, AF0) +#define GPIO9_2_GPIO MFP_CFG(GPIO9_2, AF0) +#define GPIO10_2_GPIO MFP_CFG(GPIO10_2, AF0) +#define GPIO11_2_GPIO MFP_CFG(GPIO11_2, AF0) +#define GPIO12_2_GPIO MFP_CFG(GPIO12_2, AF0) +#endif + +/* Chip Select */ +#define GPIO2_nCS3 MFP_CFG(GPIO2, AF1) + +/* AC97 */ +#define GPIO23_AC97_nACRESET MFP_CFG(GPIO23, AF1) +#define GPIO24_AC97_SYSCLK MFP_CFG(GPIO24, AF1) +#define GPIO29_AC97_BITCLK MFP_CFG(GPIO29, AF1) +#define GPIO25_AC97_SDATA_IN_0 MFP_CFG(GPIO25, AF1) +#define GPIO26_AC97_SDATA_IN_1 MFP_CFG(GPIO26, AF1) +#define GPIO17_AC97_SDATA_IN_2 MFP_CFG(GPIO17, AF3) +#define GPIO21_AC97_SDATA_IN_2 MFP_CFG(GPIO21, AF2) +#define GPIO18_AC97_SDATA_IN_3 MFP_CFG(GPIO18, AF3) +#define GPIO22_AC97_SDATA_IN_3 MFP_CFG(GPIO22, AF2) +#define GPIO27_AC97_SDATA_OUT MFP_CFG(GPIO27, AF1) +#define GPIO28_AC97_SYNC MFP_CFG(GPIO28, AF1) + +/* I2C */ +#define GPIO21_I2C_SCL MFP_CFG_LPM(GPIO21, AF1, PULL_HIGH) +#define GPIO22_I2C_SDA MFP_CFG_LPM(GPIO22, AF1, PULL_HIGH) + +/* QCI */ +#define GPIO39_CI_DD_0 MFP_CFG_DRV(GPIO39, AF1, DS04X) +#define GPIO40_CI_DD_1 MFP_CFG_DRV(GPIO40, AF1, DS04X) +#define GPIO41_CI_DD_2 MFP_CFG_DRV(GPIO41, AF1, DS04X) +#define GPIO42_CI_DD_3 MFP_CFG_DRV(GPIO42, AF1, DS04X) +#define GPIO43_CI_DD_4 MFP_CFG_DRV(GPIO43, AF1, DS04X) +#define GPIO44_CI_DD_5 MFP_CFG_DRV(GPIO44, AF1, DS04X) +#define GPIO45_CI_DD_6 MFP_CFG_DRV(GPIO45, AF1, DS04X) +#define GPIO46_CI_DD_7 MFP_CFG_DRV(GPIO46, AF0, DS04X) +#define GPIO47_CI_DD_8 MFP_CFG_DRV(GPIO47, AF1, DS04X) +#define GPIO48_CI_DD_9 MFP_CFG_DRV(GPIO48, AF1, DS04X) +#define GPIO52_CI_HSYNC MFP_CFG_DRV(GPIO52, AF0, DS04X) +#define GPIO51_CI_VSYNC MFP_CFG_DRV(GPIO51, AF0, DS04X) +#define GPIO49_CI_MCLK MFP_CFG_DRV(GPIO49, AF0, DS04X) +#define GPIO50_CI_PCLK MFP_CFG_DRV(GPIO50, AF0, DS04X) + +/* KEYPAD */ +#define GPIO3_KP_DKIN_6 MFP_CFG_LPM(GPIO3, AF2, FLOAT) +#define GPIO4_KP_DKIN_7 MFP_CFG_LPM(GPIO4, AF2, FLOAT) +#define GPIO16_KP_DKIN_6 MFP_CFG_LPM(GPIO16, AF6, FLOAT) +#define GPIO83_KP_DKIN_2 MFP_CFG_LPM(GPIO83, AF5, FLOAT) +#define GPIO84_KP_DKIN_1 MFP_CFG_LPM(GPIO84, AF5, FLOAT) +#define GPIO85_KP_DKIN_0 MFP_CFG_LPM(GPIO85, AF3, FLOAT) +#define GPIO86_KP_DKIN_1 MFP_CFG_LPM(GPIO86, AF3, FLOAT) +#define GPIO87_KP_DKIN_2 MFP_CFG_LPM(GPIO87, AF3, FLOAT) +#define GPIO88_KP_DKIN_3 MFP_CFG_LPM(GPIO88, AF3, FLOAT) +#define GPIO89_KP_DKIN_3 MFP_CFG_LPM(GPIO89, AF3, FLOAT) +#define GPIO107_KP_DKIN_0 MFP_CFG_LPM(GPIO107, AF2, FLOAT) +#define GPIO108_KP_DKIN_1 MFP_CFG_LPM(GPIO108, AF2, FLOAT) +#define GPIO109_KP_DKIN_2 MFP_CFG_LPM(GPIO109, AF2, FLOAT) +#define GPIO110_KP_DKIN_3 MFP_CFG_LPM(GPIO110, AF2, FLOAT) +#define GPIO111_KP_DKIN_4 MFP_CFG_LPM(GPIO111, AF2, FLOAT) +#define GPIO112_KP_DKIN_5 MFP_CFG_LPM(GPIO112, AF2, FLOAT) +#define GPIO113_KP_DKIN_6 MFP_CFG_LPM(GPIO113, AF2, FLOAT) +#define GPIO114_KP_DKIN_7 MFP_CFG_LPM(GPIO114, AF2, FLOAT) +#define GPIO115_KP_DKIN_0 MFP_CFG_LPM(GPIO115, AF2, FLOAT) +#define GPIO116_KP_DKIN_1 MFP_CFG_LPM(GPIO116, AF2, FLOAT) +#define GPIO117_KP_DKIN_2 MFP_CFG_LPM(GPIO117, AF2, FLOAT) +#define GPIO118_KP_DKIN_3 MFP_CFG_LPM(GPIO118, AF2, FLOAT) +#define GPIO119_KP_DKIN_4 MFP_CFG_LPM(GPIO119, AF2, FLOAT) +#define GPIO120_KP_DKIN_5 MFP_CFG_LPM(GPIO120, AF2, FLOAT) +#define GPIO121_KP_DKIN_6 MFP_CFG_LPM(GPIO121, AF2, FLOAT) +#define GPIO122_KP_DKIN_5 MFP_CFG_LPM(GPIO122, AF2, FLOAT) +#define GPIO123_KP_DKIN_4 MFP_CFG_LPM(GPIO123, AF2, FLOAT) +#define GPIO124_KP_DKIN_3 MFP_CFG_LPM(GPIO124, AF2, FLOAT) +#define GPIO127_KP_DKIN_0 MFP_CFG_LPM(GPIO127, AF5, FLOAT) +#define GPIO0_2_KP_DKIN_0 MFP_CFG_LPM(GPIO0_2, AF2, FLOAT) +#define GPIO1_2_KP_DKIN_1 MFP_CFG_LPM(GPIO1_2, AF2, FLOAT) +#define GPIO2_2_KP_DKIN_6 MFP_CFG_LPM(GPIO2_2, AF2, FLOAT) +#define GPIO3_2_KP_DKIN_7 MFP_CFG_LPM(GPIO3_2, AF2, FLOAT) +#define GPIO4_2_KP_DKIN_1 MFP_CFG_LPM(GPIO4_2, AF2, FLOAT) +#define GPIO5_2_KP_DKIN_0 MFP_CFG_LPM(GPIO5_2, AF2, FLOAT) + +#define GPIO5_KP_MKIN_0 MFP_CFG_LPM(GPIO5, AF2, FLOAT) +#define GPIO6_KP_MKIN_1 MFP_CFG_LPM(GPIO6, AF2, FLOAT) +#define GPIO9_KP_MKIN_6 MFP_CFG_LPM(GPIO9, AF3, FLOAT) +#define GPIO10_KP_MKIN_7 MFP_CFG_LPM(GPIO10, AF3, FLOAT) +#define GPIO70_KP_MKIN_6 MFP_CFG_LPM(GPIO70, AF3, FLOAT) +#define GPIO71_KP_MKIN_7 MFP_CFG_LPM(GPIO71, AF3, FLOAT) +#define GPIO100_KP_MKIN_6 MFP_CFG_LPM(GPIO100, AF7, FLOAT) +#define GPIO101_KP_MKIN_7 MFP_CFG_LPM(GPIO101, AF7, FLOAT) +#define GPIO112_KP_MKIN_6 MFP_CFG_LPM(GPIO112, AF4, FLOAT) +#define GPIO113_KP_MKIN_7 MFP_CFG_LPM(GPIO113, AF4, FLOAT) +#define GPIO115_KP_MKIN_0 MFP_CFG_LPM(GPIO115, AF1, FLOAT) +#define GPIO116_KP_MKIN_1 MFP_CFG_LPM(GPIO116, AF1, FLOAT) +#define GPIO117_KP_MKIN_2 MFP_CFG_LPM(GPIO117, AF1, FLOAT) +#define GPIO118_KP_MKIN_3 MFP_CFG_LPM(GPIO118, AF1, FLOAT) +#define GPIO119_KP_MKIN_4 MFP_CFG_LPM(GPIO119, AF1, FLOAT) +#define GPIO120_KP_MKIN_5 MFP_CFG_LPM(GPIO120, AF1, FLOAT) +#define GPIO125_KP_MKIN_2 MFP_CFG_LPM(GPIO125, AF2, FLOAT) +#define GPIO2_2_KP_MKIN_6 MFP_CFG_LPM(GPIO2_2, AF1, FLOAT) +#define GPIO3_2_KP_MKIN_7 MFP_CFG_LPM(GPIO3_2, AF1, FLOAT) + +#define GPIO7_KP_MKOUT_5 MFP_CFG_LPM(GPIO7, AF1, DRIVE_HIGH) +#define GPIO11_KP_MKOUT_5 MFP_CFG_LPM(GPIO11, AF3, DRIVE_HIGH) +#define GPIO12_KP_MKOUT_6 MFP_CFG_LPM(GPIO12, AF3, DRIVE_HIGH) +#define GPIO13_KP_MKOUT_7 MFP_CFG_LPM(GPIO13, AF3, DRIVE_HIGH) +#define GPIO19_KP_MKOUT_4 MFP_CFG_LPM(GPIO19, AF3, DRIVE_HIGH) +#define GPIO20_KP_MKOUT_5 MFP_CFG_LPM(GPIO20, AF3, DRIVE_HIGH) +#define GPIO38_KP_MKOUT_5 MFP_CFG_LPM(GPIO38, AF5, DRIVE_HIGH) +#define GPIO53_KP_MKOUT_6 MFP_CFG_LPM(GPIO53, AF5, DRIVE_HIGH) +#define GPIO78_KP_MKOUT_7 MFP_CFG_LPM(GPIO78, AF5, DRIVE_HIGH) +#define GPIO85_KP_MKOUT_0 MFP_CFG_LPM(GPIO85, AF2, DRIVE_HIGH) +#define GPIO86_KP_MKOUT_1 MFP_CFG_LPM(GPIO86, AF2, DRIVE_HIGH) +#define GPIO87_KP_MKOUT_2 MFP_CFG_LPM(GPIO87, AF2, DRIVE_HIGH) +#define GPIO88_KP_MKOUT_3 MFP_CFG_LPM(GPIO88, AF2, DRIVE_HIGH) +#define GPIO104_KP_MKOUT_6 MFP_CFG_LPM(GPIO104, AF5, DRIVE_HIGH) +#define GPIO105_KP_MKOUT_7 MFP_CFG_LPM(GPIO105, AF5, DRIVE_HIGH) +#define GPIO121_KP_MKOUT_0 MFP_CFG_LPM(GPIO121, AF1, DRIVE_HIGH) +#define GPIO122_KP_MKOUT_1 MFP_CFG_LPM(GPIO122, AF1, DRIVE_HIGH) +#define GPIO123_KP_MKOUT_2 MFP_CFG_LPM(GPIO123, AF1, DRIVE_HIGH) +#define GPIO124_KP_MKOUT_3 MFP_CFG_LPM(GPIO124, AF1, DRIVE_HIGH) +#define GPIO125_KP_MKOUT_4 MFP_CFG_LPM(GPIO125, AF1, DRIVE_HIGH) +#define GPIO126_KP_MKOUT_7 MFP_CFG_LPM(GPIO126, AF4, DRIVE_HIGH) +#define GPIO5_2_KP_MKOUT_6 MFP_CFG_LPM(GPIO5_2, AF1, DRIVE_HIGH) +#define GPIO4_2_KP_MKOUT_5 MFP_CFG_LPM(GPIO4_2, AF1, DRIVE_HIGH) +#define GPIO6_2_KP_MKOUT_7 MFP_CFG_LPM(GPIO6_2, AF1, DRIVE_HIGH) + +/* LCD */ +#define GPIO54_LCD_LDD_0 MFP_CFG_DRV(GPIO54, AF1, DS01X) +#define GPIO55_LCD_LDD_1 MFP_CFG_DRV(GPIO55, AF1, DS01X) +#define GPIO56_LCD_LDD_2 MFP_CFG_DRV(GPIO56, AF1, DS01X) +#define GPIO57_LCD_LDD_3 MFP_CFG_DRV(GPIO57, AF1, DS01X) +#define GPIO58_LCD_LDD_4 MFP_CFG_DRV(GPIO58, AF1, DS01X) +#define GPIO59_LCD_LDD_5 MFP_CFG_DRV(GPIO59, AF1, DS01X) +#define GPIO60_LCD_LDD_6 MFP_CFG_DRV(GPIO60, AF1, DS01X) +#define GPIO61_LCD_LDD_7 MFP_CFG_DRV(GPIO61, AF1, DS01X) +#define GPIO62_LCD_LDD_8 MFP_CFG_DRV(GPIO62, AF1, DS01X) +#define GPIO63_LCD_LDD_9 MFP_CFG_DRV(GPIO63, AF1, DS01X) +#define GPIO64_LCD_LDD_10 MFP_CFG_DRV(GPIO64, AF1, DS01X) +#define GPIO65_LCD_LDD_11 MFP_CFG_DRV(GPIO65, AF1, DS01X) +#define GPIO66_LCD_LDD_12 MFP_CFG_DRV(GPIO66, AF1, DS01X) +#define GPIO67_LCD_LDD_13 MFP_CFG_DRV(GPIO67, AF1, DS01X) +#define GPIO68_LCD_LDD_14 MFP_CFG_DRV(GPIO68, AF1, DS01X) +#define GPIO69_LCD_LDD_15 MFP_CFG_DRV(GPIO69, AF1, DS01X) +#define GPIO70_LCD_LDD_16 MFP_CFG_DRV(GPIO70, AF1, DS01X) +#define GPIO71_LCD_LDD_17 MFP_CFG_DRV(GPIO71, AF1, DS01X) +#define GPIO62_LCD_CS_N MFP_CFG_DRV(GPIO62, AF2, DS01X) +#define GPIO72_LCD_FCLK MFP_CFG_DRV(GPIO72, AF1, DS01X) +#define GPIO73_LCD_LCLK MFP_CFG_DRV(GPIO73, AF1, DS01X) +#define GPIO74_LCD_PCLK MFP_CFG_DRV(GPIO74, AF1, DS02X) +#define GPIO75_LCD_BIAS MFP_CFG_DRV(GPIO75, AF1, DS01X) +#define GPIO76_LCD_VSYNC MFP_CFG_DRV(GPIO76, AF2, DS01X) + +#define GPIO15_LCD_CS_N MFP_CFG_DRV(GPIO15, AF2, DS01X) +#define GPIO127_LCD_CS_N MFP_CFG_DRV(GPIO127, AF1, DS01X) +#define GPIO63_LCD_VSYNC MFP_CFG_DRV(GPIO63, AF2, DS01X) + +/* Mini-LCD */ +#define GPIO72_MLCD_FCLK MFP_CFG_DRV(GPIO72, AF7, DS08X) +#define GPIO73_MLCD_LCLK MFP_CFG_DRV(GPIO73, AF7, DS08X) +#define GPIO54_MLCD_LDD_0 MFP_CFG_DRV(GPIO54, AF7, DS08X) +#define GPIO55_MLCD_LDD_1 MFP_CFG_DRV(GPIO55, AF7, DS08X) +#define GPIO56_MLCD_LDD_2 MFP_CFG_DRV(GPIO56, AF7, DS08X) +#define GPIO57_MLCD_LDD_3 MFP_CFG_DRV(GPIO57, AF7, DS08X) +#define GPIO58_MLCD_LDD_4 MFP_CFG_DRV(GPIO58, AF7, DS08X) +#define GPIO59_MLCD_LDD_5 MFP_CFG_DRV(GPIO59, AF7, DS08X) +#define GPIO60_MLCD_LDD_6 MFP_CFG_DRV(GPIO60, AF7, DS08X) +#define GPIO61_MLCD_LDD_7 MFP_CFG_DRV(GPIO61, AF7, DS08X) +#define GPIO62_MLCD_LDD_8 MFP_CFG_DRV(GPIO62, AF7, DS08X) +#define GPIO63_MLCD_LDD_9 MFP_CFG_DRV(GPIO63, AF7, DS08X) +#define GPIO64_MLCD_LDD_10 MFP_CFG_DRV(GPIO64, AF7, DS08X) +#define GPIO65_MLCD_LDD_11 MFP_CFG_DRV(GPIO65, AF7, DS08X) +#define GPIO66_MLCD_LDD_12 MFP_CFG_DRV(GPIO66, AF7, DS08X) +#define GPIO67_MLCD_LDD_13 MFP_CFG_DRV(GPIO67, AF7, DS08X) +#define GPIO68_MLCD_LDD_14 MFP_CFG_DRV(GPIO68, AF7, DS08X) +#define GPIO69_MLCD_LDD_15 MFP_CFG_DRV(GPIO69, AF7, DS08X) +#define GPIO74_MLCD_PCLK MFP_CFG_DRV(GPIO74, AF7, DS08X) +#define GPIO75_MLCD_BIAS MFP_CFG_DRV(GPIO75, AF2, DS08X) + +/* MMC1 */ +#define GPIO7_MMC1_CLK MFP_CFG_LPM(GPIO7, AF4, DRIVE_HIGH) +#define GPIO8_MMC1_CMD MFP_CFG_LPM(GPIO8, AF4, DRIVE_HIGH) +#define GPIO14_MMC1_CMD MFP_CFG_LPM(GPIO14, AF5, DRIVE_HIGH) +#define GPIO15_MMC1_CMD MFP_CFG_LPM(GPIO15, AF5, DRIVE_HIGH) +#define GPIO3_MMC1_DAT0 MFP_CFG_LPM(GPIO3, AF4, DRIVE_HIGH) +#define GPIO4_MMC1_DAT1 MFP_CFG_LPM(GPIO4, AF4, DRIVE_HIGH) +#define GPIO5_MMC1_DAT2 MFP_CFG_LPM(GPIO5, AF4, DRIVE_HIGH) +#define GPIO6_MMC1_DAT3 MFP_CFG_LPM(GPIO6, AF4, DRIVE_HIGH) + +/* MMC2 */ +#define GPIO9_MMC2_DAT0 MFP_CFG_LPM(GPIO9, AF4, PULL_HIGH) +#define GPIO10_MMC2_DAT1 MFP_CFG_LPM(GPIO10, AF4, PULL_HIGH) +#define GPIO11_MMC2_DAT2 MFP_CFG_LPM(GPIO11, AF4, PULL_HIGH) +#define GPIO12_MMC2_DAT3 MFP_CFG_LPM(GPIO12, AF4, PULL_HIGH) +#define GPIO13_MMC2_CLK MFP_CFG_LPM(GPIO13, AF4, PULL_HIGH) +#define GPIO14_MMC2_CMD MFP_CFG_LPM(GPIO14, AF4, PULL_HIGH) +#define GPIO77_MMC2_DAT0 MFP_CFG_LPM(GPIO77, AF4, PULL_HIGH) +#define GPIO78_MMC2_DAT1 MFP_CFG_LPM(GPIO78, AF4, PULL_HIGH) +#define GPIO79_MMC2_DAT2 MFP_CFG_LPM(GPIO79, AF4, PULL_HIGH) +#define GPIO80_MMC2_DAT3 MFP_CFG_LPM(GPIO80, AF4, PULL_HIGH) +#define GPIO81_MMC2_CLK MFP_CFG_LPM(GPIO81, AF4, PULL_HIGH) +#define GPIO82_MMC2_CMD MFP_CFG_LPM(GPIO82, AF4, PULL_HIGH) + +/* SSP1 */ +#define GPIO89_SSP1_EXTCLK MFP_CFG(GPIO89, AF1) +#define GPIO90_SSP1_SYSCLK MFP_CFG(GPIO90, AF1) +#define GPIO15_SSP1_SCLK MFP_CFG(GPIO15, AF6) +#define GPIO16_SSP1_FRM MFP_CFG(GPIO16, AF2) +#define GPIO33_SSP1_SCLK MFP_CFG(GPIO33, AF5) +#define GPIO34_SSP1_FRM MFP_CFG(GPIO34, AF5) +#define GPIO85_SSP1_SCLK MFP_CFG(GPIO85, AF1) +#define GPIO86_SSP1_FRM MFP_CFG(GPIO86, AF1) +#define GPIO18_SSP1_TXD MFP_CFG(GPIO18, AF7) +#define GPIO18_SSP1_RXD MFP_CFG(GPIO18, AF2) +#define GPIO20_SSP1_TXD MFP_CFG(GPIO20, AF2) +#define GPIO20_SSP1_RXD MFP_CFG(GPIO20, AF7) +#define GPIO35_SSP1_TXD MFP_CFG(GPIO35, AF5) +#define GPIO35_SSP1_RXD MFP_CFG(GPIO35, AF4) +#define GPIO36_SSP1_TXD MFP_CFG(GPIO36, AF5) +#define GPIO36_SSP1_RXD MFP_CFG(GPIO36, AF6) +#define GPIO87_SSP1_TXD MFP_CFG(GPIO87, AF1) +#define GPIO87_SSP1_RXD MFP_CFG(GPIO87, AF6) +#define GPIO88_SSP1_TXD MFP_CFG(GPIO88, AF6) +#define GPIO88_SSP1_RXD MFP_CFG(GPIO88, AF1) + +/* SSP2 */ +#define GPIO29_SSP2_EXTCLK MFP_CFG(GPIO29, AF2) +#define GPIO23_SSP2_SCLK MFP_CFG(GPIO23, AF2) +#define GPIO17_SSP2_FRM MFP_CFG(GPIO17, AF2) +#define GPIO25_SSP2_SCLK MFP_CFG(GPIO25, AF2) +#define GPIO26_SSP2_FRM MFP_CFG(GPIO26, AF2) +#define GPIO33_SSP2_SCLK MFP_CFG(GPIO33, AF6) +#define GPIO34_SSP2_FRM MFP_CFG(GPIO34, AF6) +#define GPIO64_SSP2_SCLK MFP_CFG(GPIO64, AF2) +#define GPIO65_SSP2_FRM MFP_CFG(GPIO65, AF2) +#define GPIO19_SSP2_TXD MFP_CFG(GPIO19, AF2) +#define GPIO19_SSP2_RXD MFP_CFG(GPIO19, AF7) +#define GPIO24_SSP2_TXD MFP_CFG(GPIO24, AF5) +#define GPIO24_SSP2_RXD MFP_CFG(GPIO24, AF4) +#define GPIO27_SSP2_TXD MFP_CFG(GPIO27, AF2) +#define GPIO27_SSP2_RXD MFP_CFG(GPIO27, AF5) +#define GPIO28_SSP2_TXD MFP_CFG(GPIO28, AF5) +#define GPIO28_SSP2_RXD MFP_CFG(GPIO28, AF2) +#define GPIO35_SSP2_TXD MFP_CFG(GPIO35, AF7) +#define GPIO35_SSP2_RXD MFP_CFG(GPIO35, AF6) +#define GPIO66_SSP2_TXD MFP_CFG(GPIO66, AF4) +#define GPIO66_SSP2_RXD MFP_CFG(GPIO66, AF2) +#define GPIO67_SSP2_TXD MFP_CFG(GPIO67, AF2) +#define GPIO67_SSP2_RXD MFP_CFG(GPIO67, AF4) +#define GPIO36_SSP2_TXD MFP_CFG(GPIO36, AF7) + +/* SSP3 */ +#define GPIO69_SSP3_FRM MFP_CFG_X(GPIO69, AF2, DS08X, DRIVE_LOW) +#define GPIO68_SSP3_SCLK MFP_CFG_X(GPIO68, AF2, DS08X, FLOAT) +#define GPIO92_SSP3_FRM MFP_CFG_X(GPIO92, AF1, DS08X, DRIVE_LOW) +#define GPIO91_SSP3_SCLK MFP_CFG_X(GPIO91, AF1, DS08X, FLOAT) +#define GPIO70_SSP3_TXD MFP_CFG_X(GPIO70, AF2, DS08X, DRIVE_LOW) +#define GPIO70_SSP3_RXD MFP_CFG_X(GPIO70, AF5, DS08X, FLOAT) +#define GPIO71_SSP3_TXD MFP_CFG_X(GPIO71, AF5, DS08X, DRIVE_LOW) +#define GPIO71_SSP3_RXD MFP_CFG_X(GPIO71, AF2, DS08X, FLOAT) +#define GPIO93_SSP3_TXD MFP_CFG_X(GPIO93, AF1, DS08X, DRIVE_LOW) +#define GPIO93_SSP3_RXD MFP_CFG_X(GPIO93, AF5, DS08X, FLOAT) +#define GPIO94_SSP3_TXD MFP_CFG_X(GPIO94, AF5, DS08X, DRIVE_LOW) +#define GPIO94_SSP3_RXD MFP_CFG_X(GPIO94, AF1, DS08X, FLOAT) + +/* SSP4 */ +#define GPIO95_SSP4_SCLK MFP_CFG_LPM(GPIO95, AF1, PULL_HIGH) +#define GPIO96_SSP4_FRM MFP_CFG_LPM(GPIO96, AF1, PULL_HIGH) +#define GPIO97_SSP4_TXD MFP_CFG_LPM(GPIO97, AF1, PULL_HIGH) +#define GPIO97_SSP4_RXD MFP_CFG_LPM(GPIO97, AF5, PULL_HIGH) +#define GPIO98_SSP4_TXD MFP_CFG_LPM(GPIO98, AF5, PULL_HIGH) +#define GPIO98_SSP4_RXD MFP_CFG_LPM(GPIO98, AF1, PULL_HIGH) + +/* UART1 */ +#define GPIO32_UART1_CTS MFP_CFG_LPM(GPIO32, AF2, FLOAT) +#define GPIO37_UART1_CTS MFP_CFG_LPM(GPIO37, AF4, FLOAT) +#define GPIO79_UART1_CTS MFP_CFG_LPM(GPIO79, AF1, FLOAT) +#define GPIO84_UART1_CTS MFP_CFG_LPM(GPIO84, AF3, FLOAT) +#define GPIO101_UART1_CTS MFP_CFG_LPM(GPIO101, AF1, FLOAT) +#define GPIO106_UART1_CTS MFP_CFG_LPM(GPIO106, AF6, FLOAT) + +#define GPIO32_UART1_RTS MFP_CFG_LPM(GPIO32, AF4, FLOAT) +#define GPIO37_UART1_RTS MFP_CFG_LPM(GPIO37, AF2, FLOAT) +#define GPIO79_UART1_RTS MFP_CFG_LPM(GPIO79, AF3, FLOAT) +#define GPIO84_UART1_RTS MFP_CFG_LPM(GPIO84, AF1, FLOAT) +#define GPIO101_UART1_RTS MFP_CFG_LPM(GPIO101, AF6, FLOAT) +#define GPIO106_UART1_RTS MFP_CFG_LPM(GPIO106, AF1, FLOAT) + +#define GPIO34_UART1_DSR MFP_CFG_LPM(GPIO34, AF2, FLOAT) +#define GPIO36_UART1_DSR MFP_CFG_LPM(GPIO36, AF4, FLOAT) +#define GPIO81_UART1_DSR MFP_CFG_LPM(GPIO81, AF1, FLOAT) +#define GPIO83_UART1_DSR MFP_CFG_LPM(GPIO83, AF3, FLOAT) +#define GPIO103_UART1_DSR MFP_CFG_LPM(GPIO103, AF1, FLOAT) +#define GPIO105_UART1_DSR MFP_CFG_LPM(GPIO105, AF6, FLOAT) + +#define GPIO34_UART1_DTR MFP_CFG_LPM(GPIO34, AF4, FLOAT) +#define GPIO36_UART1_DTR MFP_CFG_LPM(GPIO36, AF2, FLOAT) +#define GPIO81_UART1_DTR MFP_CFG_LPM(GPIO81, AF3, FLOAT) +#define GPIO83_UART1_DTR MFP_CFG_LPM(GPIO83, AF1, FLOAT) +#define GPIO103_UART1_DTR MFP_CFG_LPM(GPIO103, AF6, FLOAT) +#define GPIO105_UART1_DTR MFP_CFG_LPM(GPIO105, AF1, FLOAT) + +#define GPIO35_UART1_RI MFP_CFG_LPM(GPIO35, AF2, FLOAT) +#define GPIO82_UART1_RI MFP_CFG_LPM(GPIO82, AF1, FLOAT) +#define GPIO104_UART1_RI MFP_CFG_LPM(GPIO104, AF1, FLOAT) + +#define GPIO33_UART1_DCD MFP_CFG_LPM(GPIO33, AF2, FLOAT) +#define GPIO80_UART1_DCD MFP_CFG_LPM(GPIO80, AF1, FLOAT) +#define GPIO102_UART1_DCD MFP_CFG_LPM(GPIO102, AF1, FLOAT) + +#define GPIO30_UART1_RXD MFP_CFG_LPM(GPIO30, AF2, FLOAT) +#define GPIO31_UART1_RXD MFP_CFG_LPM(GPIO31, AF4, FLOAT) +#define GPIO77_UART1_RXD MFP_CFG_LPM(GPIO77, AF1, FLOAT) +#define GPIO78_UART1_RXD MFP_CFG_LPM(GPIO78, AF3, FLOAT) +#define GPIO99_UART1_RXD MFP_CFG_LPM(GPIO99, AF1, FLOAT) +#define GPIO100_UART1_RXD MFP_CFG_LPM(GPIO100, AF6, FLOAT) +#define GPIO102_UART1_RXD MFP_CFG_LPM(GPIO102, AF6, FLOAT) +#define GPIO104_UART1_RXD MFP_CFG_LPM(GPIO104, AF4, FLOAT) + +#define GPIO30_UART1_TXD MFP_CFG_LPM(GPIO30, AF4, FLOAT) +#define GPIO31_UART1_TXD MFP_CFG_LPM(GPIO31, AF2, FLOAT) +#define GPIO77_UART1_TXD MFP_CFG_LPM(GPIO77, AF3, FLOAT) +#define GPIO78_UART1_TXD MFP_CFG_LPM(GPIO78, AF1, FLOAT) +#define GPIO99_UART1_TXD MFP_CFG_LPM(GPIO99, AF6, FLOAT) +#define GPIO100_UART1_TXD MFP_CFG_LPM(GPIO100, AF1, FLOAT) +#define GPIO102_UART1_TXD MFP_CFG_LPM(GPIO102, AF4, FLOAT) + +/* UART2 */ +#define GPIO15_UART2_CTS MFP_CFG_LPM(GPIO15, AF3, FLOAT) +#define GPIO16_UART2_CTS MFP_CFG_LPM(GPIO16, AF5, FLOAT) +#define GPIO111_UART2_CTS MFP_CFG_LPM(GPIO111, AF3, FLOAT) +#define GPIO114_UART2_CTS MFP_CFG_LPM(GPIO114, AF1, FLOAT) + +#define GPIO15_UART2_RTS MFP_CFG_LPM(GPIO15, AF4, FLOAT) +#define GPIO16_UART2_RTS MFP_CFG_LPM(GPIO16, AF4, FLOAT) +#define GPIO114_UART2_RTS MFP_CFG_LPM(GPIO114, AF3, FLOAT) +#define GPIO111_UART2_RTS MFP_CFG_LPM(GPIO111, AF1, FLOAT) + +#define GPIO18_UART2_RXD MFP_CFG_LPM(GPIO18, AF5, FLOAT) +#define GPIO19_UART2_RXD MFP_CFG_LPM(GPIO19, AF4, FLOAT) +#define GPIO112_UART2_RXD MFP_CFG_LPM(GPIO112, AF1, FLOAT) +#define GPIO113_UART2_RXD MFP_CFG_LPM(GPIO113, AF3, FLOAT) + +#define GPIO18_UART2_TXD MFP_CFG_LPM(GPIO18, AF4, FLOAT) +#define GPIO19_UART2_TXD MFP_CFG_LPM(GPIO19, AF5, FLOAT) +#define GPIO112_UART2_TXD MFP_CFG_LPM(GPIO112, AF3, FLOAT) +#define GPIO113_UART2_TXD MFP_CFG_LPM(GPIO113, AF1, FLOAT) + +/* UART3 */ +#define GPIO91_UART3_CTS MFP_CFG_LPM(GPIO91, AF2, FLOAT) +#define GPIO92_UART3_CTS MFP_CFG_LPM(GPIO92, AF4, FLOAT) +#define GPIO107_UART3_CTS MFP_CFG_LPM(GPIO107, AF1, FLOAT) +#define GPIO108_UART3_CTS MFP_CFG_LPM(GPIO108, AF3, FLOAT) + +#define GPIO91_UART3_RTS MFP_CFG_LPM(GPIO91, AF4, FLOAT) +#define GPIO92_UART3_RTS MFP_CFG_LPM(GPIO92, AF2, FLOAT) +#define GPIO107_UART3_RTS MFP_CFG_LPM(GPIO107, AF3, FLOAT) +#define GPIO108_UART3_RTS MFP_CFG_LPM(GPIO108, AF1, FLOAT) + +#define GPIO7_UART3_RXD MFP_CFG_LPM(GPIO7, AF2, FLOAT) +#define GPIO8_UART3_RXD MFP_CFG_LPM(GPIO8, AF6, FLOAT) +#define GPIO93_UART3_RXD MFP_CFG_LPM(GPIO93, AF4, FLOAT) +#define GPIO94_UART3_RXD MFP_CFG_LPM(GPIO94, AF2, FLOAT) +#define GPIO109_UART3_RXD MFP_CFG_LPM(GPIO109, AF3, FLOAT) +#define GPIO110_UART3_RXD MFP_CFG_LPM(GPIO110, AF1, FLOAT) + +#define GPIO7_UART3_TXD MFP_CFG_LPM(GPIO7, AF6, FLOAT) +#define GPIO8_UART3_TXD MFP_CFG_LPM(GPIO8, AF2, FLOAT) +#define GPIO93_UART3_TXD MFP_CFG_LPM(GPIO93, AF2, FLOAT) +#define GPIO94_UART3_TXD MFP_CFG_LPM(GPIO94, AF4, FLOAT) +#define GPIO109_UART3_TXD MFP_CFG_LPM(GPIO109, AF1, FLOAT) +#define GPIO110_UART3_TXD MFP_CFG_LPM(GPIO110, AF3, FLOAT) + +/* USB Host */ +#define GPIO0_2_USBH_PEN MFP_CFG(GPIO0_2, AF1) +#define GPIO1_2_USBH_PWR MFP_CFG(GPIO1_2, AF1) + +/* USB P3 */ +#define GPIO77_USB_P3_1 MFP_CFG(GPIO77, AF2) +#define GPIO78_USB_P3_2 MFP_CFG(GPIO78, AF2) +#define GPIO79_USB_P3_3 MFP_CFG(GPIO79, AF2) +#define GPIO80_USB_P3_4 MFP_CFG(GPIO80, AF2) +#define GPIO81_USB_P3_5 MFP_CFG(GPIO81, AF2) +#define GPIO82_USB_P3_6 MFP_CFG(GPIO82, AF2) + +/* PWM */ +#define GPIO17_PWM0_OUT MFP_CFG(GPIO17, AF1) +#define GPIO18_PWM1_OUT MFP_CFG(GPIO18, AF1) +#define GPIO19_PWM2_OUT MFP_CFG(GPIO19, AF1) +#define GPIO20_PWM3_OUT MFP_CFG(GPIO20, AF1) + +/* CIR */ +#define GPIO8_CIR_OUT MFP_CFG(GPIO8, AF5) +#define GPIO16_CIR_OUT MFP_CFG(GPIO16, AF3) + +#define GPIO20_OW_DQ_IN MFP_CFG(GPIO20, AF5) +#define GPIO126_OW_DQ MFP_CFG(GPIO126, AF2) + +#define GPIO0_DF_RDY MFP_CFG(GPIO0, AF1) +#define GPIO7_CLK_BYPASS_XSC MFP_CFG(GPIO7, AF7) +#define GPIO17_EXT_SYNC_MVT_0 MFP_CFG(GPIO17, AF6) +#define GPIO18_EXT_SYNC_MVT_1 MFP_CFG(GPIO18, AF6) +#define GPIO19_OST_CHOUT_MVT_0 MFP_CFG(GPIO19, AF6) +#define GPIO20_OST_CHOUT_MVT_1 MFP_CFG(GPIO20, AF6) +#define GPIO49_48M_CLK MFP_CFG(GPIO49, AF2) +#define GPIO126_EXT_CLK MFP_CFG(GPIO126, AF3) +#define GPIO127_CLK_BYPASS_GB MFP_CFG(GPIO127, AF7) +#define GPIO71_EXT_MATCH_MVT MFP_CFG(GPIO71, AF6) + +#define GPIO3_uIO_IN MFP_CFG(GPIO3, AF1) + +#define GPIO4_uSIM_CARD_STATE MFP_CFG(GPIO4, AF1) +#define GPIO5_uSIM_uCLK MFP_CFG(GPIO5, AF1) +#define GPIO6_uSIM_uRST MFP_CFG(GPIO6, AF1) +#define GPIO16_uSIM_UVS_0 MFP_CFG(GPIO16, AF1) + +#define GPIO9_SCIO MFP_CFG(GPIO9, AF1) +#define GPIO20_RTC_MVT MFP_CFG(GPIO20, AF4) +#define GPIO126_RTC_MVT MFP_CFG(GPIO126, AF1) + +/* + * PXA300 specific MFP configurations + */ +#ifdef CONFIG_CPU_PXA300 +#define GPIO99_USB_P2_2 MFP_CFG(GPIO99, AF2) +#define GPIO99_USB_P2_5 MFP_CFG(GPIO99, AF3) +#define GPIO99_USB_P2_6 MFP_CFG(GPIO99, AF4) +#define GPIO100_USB_P2_2 MFP_CFG(GPIO100, AF4) +#define GPIO100_USB_P2_5 MFP_CFG(GPIO100, AF5) +#define GPIO101_USB_P2_1 MFP_CFG(GPIO101, AF2) +#define GPIO102_USB_P2_4 MFP_CFG(GPIO102, AF2) +#define GPIO104_USB_P2_3 MFP_CFG(GPIO104, AF2) +#define GPIO105_USB_P2_5 MFP_CFG(GPIO105, AF2) +#define GPIO100_USB_P2_6 MFP_CFG(GPIO100, AF2) +#define GPIO106_USB_P2_7 MFP_CFG(GPIO106, AF2) +#define GPIO103_USB_P2_8 MFP_CFG(GPIO103, AF2) + +/* U2D UTMI */ +#define GPIO38_UTM_CLK MFP_CFG(GPIO38, AF1) +#define GPIO26_U2D_RXERROR MFP_CFG(GPIO26, AF3) +#define GPIO50_U2D_RXERROR MFP_CFG(GPIO50, AF1) +#define GPIO89_U2D_RXERROR MFP_CFG(GPIO89, AF5) +#define GPIO24_UTM_RXVALID MFP_CFG(GPIO24, AF3) +#define GPIO48_UTM_RXVALID MFP_CFG(GPIO48, AF2) +#define GPIO87_UTM_RXVALID MFP_CFG(GPIO87, AF5) +#define GPIO25_UTM_RXACTIVE MFP_CFG(GPIO25, AF3) +#define GPIO47_UTM_RXACTIVE MFP_CFG(GPIO47, AF2) +#define GPIO49_UTM_RXACTIVE MFP_CFG(GPIO49, AF1) +#define GPIO88_UTM_RXACTIVE MFP_CFG(GPIO88, AF5) +#define GPIO53_UTM_TXREADY MFP_CFG(GPIO53, AF1) +#define GPIO67_UTM_LINESTATE_0 MFP_CFG(GPIO67, AF3) +#define GPIO92_UTM_LINESTATE_0 MFP_CFG(GPIO92, AF3) +#define GPIO104_UTM_LINESTATE_0 MFP_CFG(GPIO104, AF3) +#define GPIO109_UTM_LINESTATE_0 MFP_CFG(GPIO109, AF4) +#define GPIO68_UTM_LINESTATE_1 MFP_CFG(GPIO68, AF3) +#define GPIO93_UTM_LINESTATE_1 MFP_CFG(GPIO93, AF3) +#define GPIO105_UTM_LINESTATE_1 MFP_CFG(GPIO105, AF3) +#define GPIO27_U2D_OPMODE_0 MFP_CFG(GPIO27, AF4) +#define GPIO51_U2D_OPMODE_0 MFP_CFG(GPIO51, AF2) +#define GPIO90_U2D_OPMODE_0 MFP_CFG(GPIO90, AF7) +#define GPIO28_U2D_OPMODE_1 MFP_CFG(GPIO28, AF4) +#define GPIO52_U2D_OPMODE_1 MFP_CFG(GPIO52, AF2) +#define GPIO106_U2D_OPMODE_1 MFP_CFG(GPIO106, AF3) +#define GPIO110_U2D_OPMODE_1 MFP_CFG(GPIO110, AF5) +#define GPIO76_U2D_RESET MFP_CFG(GPIO76, AF1) +#define GPIO95_U2D_RESET MFP_CFG(GPIO95, AF2) +#define GPIO100_U2D_RESET MFP_CFG(GPIO100, AF3) +#define GPIO66_U2D_SUSPEND MFP_CFG(GPIO66, AF3) +#define GPIO98_U2D_SUSPEND MFP_CFG(GPIO98, AF2) +#define GPIO103_U2D_SUSPEND MFP_CFG(GPIO103, AF3) +#define GPIO65_U2D_TERM_SEL MFP_CFG(GPIO65, AF5) +#define GPIO97_U2D_TERM_SEL MFP_CFG(GPIO97, AF3) +#define GPIO102_U2D_TERM_SEL MFP_CFG(GPIO102, AF5) +#define GPIO29_U2D_TXVALID MFP_CFG(GPIO29, AF3) +#define GPIO52_U2D_TXVALID MFP_CFG(GPIO52, AF4) +#define GPIO69_U2D_TXVALID MFP_CFG(GPIO69, AF3) +#define GPIO85_U2D_TXVALID MFP_CFG(GPIO85, AF7) +#define GPIO64_U2D_XCVR_SEL MFP_CFG(GPIO64, AF5) +#define GPIO96_U2D_XCVR_SEL MFP_CFG(GPIO96, AF3) +#define GPIO101_U2D_XCVR_SEL MFP_CFG(GPIO101, AF5) +#define GPIO30_UTM_PHYDATA_0 MFP_CFG(GPIO30, AF3) +#define GPIO31_UTM_PHYDATA_1 MFP_CFG(GPIO31, AF3) +#define GPIO32_UTM_PHYDATA_2 MFP_CFG(GPIO32, AF3) +#define GPIO33_UTM_PHYDATA_3 MFP_CFG(GPIO33, AF3) +#define GPIO34_UTM_PHYDATA_4 MFP_CFG(GPIO34, AF3) +#define GPIO35_UTM_PHYDATA_5 MFP_CFG(GPIO35, AF3) +#define GPIO36_UTM_PHYDATA_6 MFP_CFG(GPIO36, AF3) +#define GPIO37_UTM_PHYDATA_7 MFP_CFG(GPIO37, AF3) +#define GPIO39_UTM_PHYDATA_0 MFP_CFG(GPIO39, AF3) +#define GPIO40_UTM_PHYDATA_1 MFP_CFG(GPIO40, AF3) +#define GPIO41_UTM_PHYDATA_2 MFP_CFG(GPIO41, AF3) +#define GPIO42_UTM_PHYDATA_3 MFP_CFG(GPIO42, AF3) +#define GPIO43_UTM_PHYDATA_4 MFP_CFG(GPIO43, AF3) +#define GPIO44_UTM_PHYDATA_5 MFP_CFG(GPIO44, AF3) +#define GPIO45_UTM_PHYDATA_6 MFP_CFG(GPIO45, AF3) +#define GPIO46_UTM_PHYDATA_7 MFP_CFG(GPIO46, AF3) +#endif /* CONFIG_CPU_PXA300 */ + +/* + * PXA310 specific MFP configurations + */ +#ifdef CONFIG_CPU_PXA310 +/* USB P2 */ +#define GPIO36_USB_P2_1 MFP_CFG(GPIO36, AF1) +#define GPIO30_USB_P2_2 MFP_CFG(GPIO30, AF1) +#define GPIO35_USB_P2_3 MFP_CFG(GPIO35, AF1) +#define GPIO32_USB_P2_4 MFP_CFG(GPIO32, AF1) +#define GPIO34_USB_P2_5 MFP_CFG(GPIO34, AF1) +#define GPIO31_USB_P2_6 MFP_CFG(GPIO31, AF1) + +/* MMC1 */ +#define GPIO24_MMC1_CMD MFP_CFG(GPIO24, AF3) +#define GPIO29_MMC1_DAT0 MFP_CFG(GPIO29, AF3) + +/* MMC3 */ +#define GPIO103_MMC3_CLK MFP_CFG(GPIO103, AF2) +#define GPIO105_MMC3_CMD MFP_CFG(GPIO105, AF2) +#define GPIO11_2_MMC3_CLK MFP_CFG(GPIO11_2, AF1) +#define GPIO12_2_MMC3_CMD MFP_CFG(GPIO12_2, AF1) +#define GPIO7_2_MMC3_DAT0 MFP_CFG(GPIO7_2, AF1) +#define GPIO8_2_MMC3_DAT1 MFP_CFG(GPIO8_2, AF1) +#define GPIO9_2_MMC3_DAT2 MFP_CFG(GPIO9_2, AF1) +#define GPIO10_2_MMC3_DAT3 MFP_CFG(GPIO10_2, AF1) + +/* ULPI */ +#define GPIO38_ULPI_CLK MFP_CFG(GPIO38, AF1) +#define GPIO30_ULPI_DATA_OUT_0 MFP_CFG(GPIO30, AF3) +#define GPIO31_ULPI_DATA_OUT_1 MFP_CFG(GPIO31, AF3) +#define GPIO32_ULPI_DATA_OUT_2 MFP_CFG(GPIO32, AF3) +#define GPIO33_ULPI_DATA_OUT_3 MFP_CFG(GPIO33, AF3) +#define GPIO34_ULPI_DATA_OUT_4 MFP_CFG(GPIO34, AF3) +#define GPIO35_ULPI_DATA_OUT_5 MFP_CFG(GPIO35, AF3) +#define GPIO36_ULPI_DATA_OUT_6 MFP_CFG(GPIO36, AF3) +#define GPIO37_ULPI_DATA_OUT_7 MFP_CFG(GPIO37, AF3) +#define GPIO33_ULPI_OTG_INTR MFP_CFG(GPIO33, AF1) + +#define ULPI_DIR MFP_CFG_DRV(ULPI_DIR, MFP_AF0, MFP_DS01X) +#define ULPI_NXT MFP_CFG_DRV(ULPI_NXT, MFP_AF0, MFP_DS01X) +#define ULPI_STP MFP_CFG_DRV(ULPI_STP, MFP_AF0, MFP_DS01X) +#endif /* CONFIG_CPU_PXA310 */ + +#endif /* __ASM_ARCH_MFP_PXA300_H */ diff --git a/arch/arm/mach-pxa/include/mach/mfp-pxa320.h b/arch/arm/mach-pxa/include/mach/mfp-pxa320.h new file mode 100644 index 00000000000..67f8385ea54 --- /dev/null +++ b/arch/arm/mach-pxa/include/mach/mfp-pxa320.h @@ -0,0 +1,447 @@ +/* + * arch/arm/mach-pxa/include/mach/mfp-pxa320.h + * + * PXA320 specific MFP configuration definitions + * + * Copyright (C) 2007 Marvell International Ltd. + * 2007-08-21: eric miao <eric.miao@marvell.com> + * initial version + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ + +#ifndef __ASM_ARCH_MFP_PXA320_H +#define __ASM_ARCH_MFP_PXA320_H + +#include <mach/mfp.h> +#include <mach/mfp-pxa3xx.h> + +/* GPIO */ +#define GPIO46_GPIO MFP_CFG(GPIO46, AF0) +#define GPIO49_GPIO MFP_CFG(GPIO49, AF0) +#define GPIO50_GPIO MFP_CFG(GPIO50, AF0) +#define GPIO51_GPIO MFP_CFG(GPIO51, AF0) +#define GPIO52_GPIO MFP_CFG(GPIO52, AF0) + +#define GPIO7_2_GPIO MFP_CFG(GPIO7_2, AF0) +#define GPIO8_2_GPIO MFP_CFG(GPIO8_2, AF0) +#define GPIO9_2_GPIO MFP_CFG(GPIO9_2, AF0) +#define GPIO10_2_GPIO MFP_CFG(GPIO10_2, AF0) +#define GPIO11_2_GPIO MFP_CFG(GPIO11_2, AF0) +#define GPIO12_2_GPIO MFP_CFG(GPIO12_2, AF0) +#define GPIO13_2_GPIO MFP_CFG(GPIO13_2, AF0) +#define GPIO14_2_GPIO MFP_CFG(GPIO14_2, AF0) +#define GPIO15_2_GPIO MFP_CFG(GPIO15_2, AF0) +#define GPIO16_2_GPIO MFP_CFG(GPIO16_2, AF0) +#define GPIO17_2_GPIO MFP_CFG(GPIO17_2, AF0) + +/* Chip Select */ +#define GPIO4_nCS3 MFP_CFG(GPIO4, AF1) + +/* AC97 */ +#define GPIO34_AC97_SYSCLK MFP_CFG(GPIO34, AF1) +#define GPIO39_AC97_BITCLK MFP_CFG(GPIO39, AF1) +#define GPIO40_AC97_nACRESET MFP_CFG(GPIO40, AF1) +#define GPIO35_AC97_SDATA_IN_0 MFP_CFG(GPIO35, AF1) +#define GPIO36_AC97_SDATA_IN_1 MFP_CFG(GPIO36, AF1) +#define GPIO32_AC97_SDATA_IN_2 MFP_CFG(GPIO32, AF2) +#define GPIO33_AC97_SDATA_IN_3 MFP_CFG(GPIO33, AF2) +#define GPIO11_AC97_SDATA_IN_2 MFP_CFG(GPIO11, AF3) +#define GPIO12_AC97_SDATA_IN_3 MFP_CFG(GPIO12, AF3) +#define GPIO37_AC97_SDATA_OUT MFP_CFG(GPIO37, AF1) +#define GPIO38_AC97_SYNC MFP_CFG(GPIO38, AF1) + +/* I2C */ +#define GPIO32_I2C_SCL MFP_CFG_LPM(GPIO32, AF1, PULL_HIGH) +#define GPIO33_I2C_SDA MFP_CFG_LPM(GPIO33, AF1, PULL_HIGH) + +/* QCI */ +#define GPIO49_CI_DD_0 MFP_CFG_DRV(GPIO49, AF1, DS04X) +#define GPIO50_CI_DD_1 MFP_CFG_DRV(GPIO50, AF1, DS04X) +#define GPIO51_CI_DD_2 MFP_CFG_DRV(GPIO51, AF1, DS04X) +#define GPIO52_CI_DD_3 MFP_CFG_DRV(GPIO52, AF1, DS04X) +#define GPIO53_CI_DD_4 MFP_CFG_DRV(GPIO53, AF1, DS04X) +#define GPIO54_CI_DD_5 MFP_CFG_DRV(GPIO54, AF1, DS04X) +#define GPIO55_CI_DD_6 MFP_CFG_DRV(GPIO55, AF1, DS04X) +#define GPIO56_CI_DD_7 MFP_CFG_DRV(GPIO56, AF0, DS04X) +#define GPIO57_CI_DD_8 MFP_CFG_DRV(GPIO57, AF1, DS04X) +#define GPIO58_CI_DD_9 MFP_CFG_DRV(GPIO58, AF1, DS04X) +#define GPIO59_CI_MCLK MFP_CFG_DRV(GPIO59, AF0, DS04X) +#define GPIO60_CI_PCLK MFP_CFG_DRV(GPIO60, AF0, DS04X) +#define GPIO61_CI_HSYNC MFP_CFG_DRV(GPIO61, AF0, DS04X) +#define GPIO62_CI_VSYNC MFP_CFG_DRV(GPIO62, AF0, DS04X) + +#define GPIO31_CIR_OUT MFP_CFG(GPIO31, AF5) + +#define GPIO0_2_CLK_EXT MFP_CFG(GPIO0_2, AF3) +#define GPIO0_DRQ MFP_CFG(GPIO0, AF2) +#define GPIO11_EXT_SYNC0 MFP_CFG(GPIO11, AF5) +#define GPIO12_EXT_SYNC1 MFP_CFG(GPIO12, AF6) +#define GPIO0_2_HZ_CLK MFP_CFG(GPIO0_2, AF1) +#define GPIO14_HZ_CLK MFP_CFG(GPIO14, AF4) +#define GPIO30_ICP_RXD MFP_CFG(GPIO30, AF1) +#define GPIO31_ICP_TXD MFP_CFG(GPIO31, AF1) + +#define GPIO83_KP_DKIN_0 MFP_CFG_LPM(GPIO83, AF3, FLOAT) +#define GPIO84_KP_DKIN_1 MFP_CFG_LPM(GPIO84, AF3, FLOAT) +#define GPIO85_KP_DKIN_2 MFP_CFG_LPM(GPIO85, AF3, FLOAT) +#define GPIO86_KP_DKIN_3 MFP_CFG_LPM(GPIO86, AF3, FLOAT) + +#define GPIO105_KP_DKIN_0 MFP_CFG_LPM(GPIO105, AF2, FLOAT) +#define GPIO106_KP_DKIN_1 MFP_CFG_LPM(GPIO106, AF2, FLOAT) +#define GPIO107_KP_DKIN_2 MFP_CFG_LPM(GPIO107, AF2, FLOAT) +#define GPIO108_KP_DKIN_3 MFP_CFG_LPM(GPIO108, AF2, FLOAT) +#define GPIO109_KP_DKIN_4 MFP_CFG_LPM(GPIO109, AF2, FLOAT) +#define GPIO110_KP_DKIN_5 MFP_CFG_LPM(GPIO110, AF2, FLOAT) +#define GPIO111_KP_DKIN_6 MFP_CFG_LPM(GPIO111, AF2, FLOAT) +#define GPIO112_KP_DKIN_7 MFP_CFG_LPM(GPIO112, AF2, FLOAT) + +#define GPIO113_KP_DKIN_0 MFP_CFG_LPM(GPIO113, AF2, FLOAT) +#define GPIO114_KP_DKIN_1 MFP_CFG_LPM(GPIO114, AF2, FLOAT) +#define GPIO115_KP_DKIN_2 MFP_CFG_LPM(GPIO115, AF2, FLOAT) +#define GPIO116_KP_DKIN_3 MFP_CFG_LPM(GPIO116, AF2, FLOAT) +#define GPIO117_KP_DKIN_4 MFP_CFG_LPM(GPIO117, AF2, FLOAT) +#define GPIO118_KP_DKIN_5 MFP_CFG_LPM(GPIO118, AF2, FLOAT) +#define GPIO119_KP_DKIN_6 MFP_CFG_LPM(GPIO119, AF2, FLOAT) +#define GPIO120_KP_DKIN_7 MFP_CFG_LPM(GPIO120, AF2, FLOAT) + +#define GPIO127_KP_DKIN_0 MFP_CFG_LPM(GPIO127, AF2, FLOAT) +#define GPIO126_KP_DKIN_1 MFP_CFG_LPM(GPIO126, AF2, FLOAT) + +#define GPIO2_2_KP_DKIN_0 MFP_CFG_LPM(GPIO2_2, AF2, FLOAT) +#define GPIO3_2_KP_DKIN_1 MFP_CFG_LPM(GPIO3_2, AF2, FLOAT) +#define GPIO125_KP_DKIN_2 MFP_CFG_LPM(GPIO125, AF2, FLOAT) +#define GPIO124_KP_DKIN_3 MFP_CFG_LPM(GPIO124, AF2, FLOAT) +#define GPIO123_KP_DKIN_4 MFP_CFG_LPM(GPIO123, AF2, FLOAT) +#define GPIO122_KP_DKIN_5 MFP_CFG_LPM(GPIO122, AF2, FLOAT) +#define GPIO121_KP_DKIN_6 MFP_CFG_LPM(GPIO121, AF2, FLOAT) +#define GPIO4_2_KP_DKIN_7 MFP_CFG_LPM(GPIO4_2, AF2, FLOAT) + +#define GPIO113_KP_MKIN_0 MFP_CFG_LPM(GPIO113, AF1, FLOAT) +#define GPIO114_KP_MKIN_1 MFP_CFG_LPM(GPIO114, AF1, FLOAT) +#define GPIO115_KP_MKIN_2 MFP_CFG_LPM(GPIO115, AF1, FLOAT) +#define GPIO116_KP_MKIN_3 MFP_CFG_LPM(GPIO116, AF1, FLOAT) +#define GPIO117_KP_MKIN_4 MFP_CFG_LPM(GPIO117, AF1, FLOAT) +#define GPIO118_KP_MKIN_5 MFP_CFG_LPM(GPIO118, AF1, FLOAT) +#define GPIO119_KP_MKIN_6 MFP_CFG_LPM(GPIO119, AF1, FLOAT) +#define GPIO120_KP_MKIN_7 MFP_CFG_LPM(GPIO120, AF1, FLOAT) + +#define GPIO83_KP_MKOUT_0 MFP_CFG_LPM(GPIO83, AF2, DRIVE_HIGH) +#define GPIO84_KP_MKOUT_1 MFP_CFG_LPM(GPIO84, AF2, DRIVE_HIGH) +#define GPIO85_KP_MKOUT_2 MFP_CFG_LPM(GPIO85, AF2, DRIVE_HIGH) +#define GPIO86_KP_MKOUT_3 MFP_CFG_LPM(GPIO86, AF2, DRIVE_HIGH) +#define GPIO13_KP_MKOUT_4 MFP_CFG_LPM(GPIO13, AF3, DRIVE_HIGH) +#define GPIO14_KP_MKOUT_5 MFP_CFG_LPM(GPIO14, AF3, DRIVE_HIGH) + +#define GPIO121_KP_MKOUT_0 MFP_CFG_LPM(GPIO121, AF1, DRIVE_HIGH) +#define GPIO122_KP_MKOUT_1 MFP_CFG_LPM(GPIO122, AF1, DRIVE_HIGH) +#define GPIO123_KP_MKOUT_2 MFP_CFG_LPM(GPIO123, AF1, DRIVE_HIGH) +#define GPIO124_KP_MKOUT_3 MFP_CFG_LPM(GPIO124, AF1, DRIVE_HIGH) +#define GPIO125_KP_MKOUT_4 MFP_CFG_LPM(GPIO125, AF1, DRIVE_HIGH) +#define GPIO126_KP_MKOUT_5 MFP_CFG_LPM(GPIO126, AF1, DRIVE_HIGH) +#define GPIO127_KP_MKOUT_6 MFP_CFG_LPM(GPIO127, AF1, DRIVE_HIGH) +#define GPIO5_2_KP_MKOUT_7 MFP_CFG_LPM(GPIO5_2, AF1, DRIVE_HIGH) + +/* LCD */ +#define GPIO6_2_LCD_LDD_0 MFP_CFG_DRV(GPIO6_2, AF1, DS01X) +#define GPIO7_2_LCD_LDD_1 MFP_CFG_DRV(GPIO7_2, AF1, DS01X) +#define GPIO8_2_LCD_LDD_2 MFP_CFG_DRV(GPIO8_2, AF1, DS01X) +#define GPIO9_2_LCD_LDD_3 MFP_CFG_DRV(GPIO9_2, AF1, DS01X) +#define GPIO10_2_LCD_LDD_4 MFP_CFG_DRV(GPIO10_2, AF1, DS01X) +#define GPIO11_2_LCD_LDD_5 MFP_CFG_DRV(GPIO11_2, AF1, DS01X) +#define GPIO12_2_LCD_LDD_6 MFP_CFG_DRV(GPIO12_2, AF1, DS01X) +#define GPIO13_2_LCD_LDD_7 MFP_CFG_DRV(GPIO13_2, AF1, DS01X) +#define GPIO63_LCD_LDD_8 MFP_CFG_DRV(GPIO63, AF1, DS01X) +#define GPIO64_LCD_LDD_9 MFP_CFG_DRV(GPIO64, AF1, DS01X) +#define GPIO65_LCD_LDD_10 MFP_CFG_DRV(GPIO65, AF1, DS01X) +#define GPIO66_LCD_LDD_11 MFP_CFG_DRV(GPIO66, AF1, DS01X) +#define GPIO67_LCD_LDD_12 MFP_CFG_DRV(GPIO67, AF1, DS01X) +#define GPIO68_LCD_LDD_13 MFP_CFG_DRV(GPIO68, AF1, DS01X) +#define GPIO69_LCD_LDD_14 MFP_CFG_DRV(GPIO69, AF1, DS01X) +#define GPIO70_LCD_LDD_15 MFP_CFG_DRV(GPIO70, AF1, DS01X) +#define GPIO71_LCD_LDD_16 MFP_CFG_DRV(GPIO71, AF1, DS01X) +#define GPIO72_LCD_LDD_17 MFP_CFG_DRV(GPIO72, AF1, DS01X) +#define GPIO73_LCD_CS_N MFP_CFG_DRV(GPIO73, AF2, DS01X) +#define GPIO74_LCD_VSYNC MFP_CFG_DRV(GPIO74, AF2, DS01X) +#define GPIO14_2_LCD_FCLK MFP_CFG_DRV(GPIO14_2, AF1, DS01X) +#define GPIO15_2_LCD_LCLK MFP_CFG_DRV(GPIO15_2, AF1, DS01X) +#define GPIO16_2_LCD_PCLK MFP_CFG_DRV(GPIO16_2, AF1, DS01X) +#define GPIO17_2_LCD_BIAS MFP_CFG_DRV(GPIO17_2, AF1, DS01X) +#define GPIO64_LCD_VSYNC MFP_CFG_DRV(GPIO64, AF2, DS01X) +#define GPIO63_LCD_CS_N MFP_CFG_DRV(GPIO63, AF2, DS01X) + +#define GPIO6_2_MLCD_DD_0 MFP_CFG_DRV(GPIO6_2, AF7, DS08X) +#define GPIO7_2_MLCD_DD_1 MFP_CFG_DRV(GPIO7_2, AF7, DS08X) +#define GPIO8_2_MLCD_DD_2 MFP_CFG_DRV(GPIO8_2, AF7, DS08X) +#define GPIO9_2_MLCD_DD_3 MFP_CFG_DRV(GPIO9_2, AF7, DS08X) +#define GPIO10_2_MLCD_DD_4 MFP_CFG_DRV(GPIO10_2, AF7, DS08X) +#define GPIO11_2_MLCD_DD_5 MFP_CFG_DRV(GPIO11_2, AF7, DS08X) +#define GPIO12_2_MLCD_DD_6 MFP_CFG_DRV(GPIO12_2, AF7, DS08X) +#define GPIO13_2_MLCD_DD_7 MFP_CFG_DRV(GPIO13_2, AF7, DS08X) +#define GPIO63_MLCD_DD_8 MFP_CFG_DRV(GPIO63, AF7, DS08X) +#define GPIO64_MLCD_DD_9 MFP_CFG_DRV(GPIO64, AF7, DS08X) +#define GPIO65_MLCD_DD_10 MFP_CFG_DRV(GPIO65, AF7, DS08X) +#define GPIO66_MLCD_DD_11 MFP_CFG_DRV(GPIO66, AF7, DS08X) +#define GPIO67_MLCD_DD_12 MFP_CFG_DRV(GPIO67, AF7, DS08X) +#define GPIO68_MLCD_DD_13 MFP_CFG_DRV(GPIO68, AF7, DS08X) +#define GPIO69_MLCD_DD_14 MFP_CFG_DRV(GPIO69, AF7, DS08X) +#define GPIO70_MLCD_DD_15 MFP_CFG_DRV(GPIO70, AF7, DS08X) +#define GPIO71_MLCD_DD_16 MFP_CFG_DRV(GPIO71, AF7, DS08X) +#define GPIO72_MLCD_DD_17 MFP_CFG_DRV(GPIO72, AF7, DS08X) +#define GPIO73_MLCD_CS MFP_CFG_DRV(GPIO73, AF7, DS08X) +#define GPIO74_MLCD_VSYNC MFP_CFG_DRV(GPIO74, AF7, DS08X) +#define GPIO14_2_MLCD_FCLK MFP_CFG_DRV(GPIO14_2, AF7, DS08X) +#define GPIO15_2_MLCD_LCLK MFP_CFG_DRV(GPIO15_2, AF7, DS08X) +#define GPIO16_2_MLCD_PCLK MFP_CFG_DRV(GPIO16_2, AF7, DS08X) +#define GPIO17_2_MLCD_BIAS MFP_CFG_DRV(GPIO17_2, AF7, DS08X) + +/* MMC1 */ +#define GPIO9_MMC1_CMD MFP_CFG_LPM(GPIO9, AF4, DRIVE_HIGH) +#define GPIO22_MMC1_CLK MFP_CFG_LPM(GPIO22, AF4, DRIVE_HIGH) +#define GPIO23_MMC1_CMD MFP_CFG_LPM(GPIO23, AF4, DRIVE_HIGH) +#define GPIO30_MMC1_CLK MFP_CFG_LPM(GPIO30, AF4, DRIVE_HIGH) +#define GPIO31_MMC1_CMD MFP_CFG_LPM(GPIO31, AF4, DRIVE_HIGH) +#define GPIO5_MMC1_DAT0 MFP_CFG_LPM(GPIO5, AF4, DRIVE_HIGH) +#define GPIO6_MMC1_DAT1 MFP_CFG_LPM(GPIO6, AF4, DRIVE_HIGH) +#define GPIO7_MMC1_DAT2 MFP_CFG_LPM(GPIO7, AF4, DRIVE_HIGH) +#define GPIO8_MMC1_DAT3 MFP_CFG_LPM(GPIO8, AF4, DRIVE_HIGH) +#define GPIO18_MMC1_DAT0 MFP_CFG_LPM(GPIO18, AF4, DRIVE_HIGH) +#define GPIO19_MMC1_DAT1 MFP_CFG_LPM(GPIO19, AF4, DRIVE_HIGH) +#define GPIO20_MMC1_DAT2 MFP_CFG_LPM(GPIO20, AF4, DRIVE_HIGH) +#define GPIO21_MMC1_DAT3 MFP_CFG_LPM(GPIO21, AF4, DRIVE_HIGH) + +#define GPIO28_MMC2_CLK MFP_CFG_LPM(GPIO28, AF4, PULL_HIGH) +#define GPIO29_MMC2_CMD MFP_CFG_LPM(GPIO29, AF4, PULL_HIGH) +#define GPIO30_MMC2_CLK MFP_CFG_LPM(GPIO30, AF3, PULL_HIGH) +#define GPIO31_MMC2_CMD MFP_CFG_LPM(GPIO31, AF3, PULL_HIGH) +#define GPIO79_MMC2_CLK MFP_CFG_LPM(GPIO79, AF4, PULL_HIGH) +#define GPIO80_MMC2_CMD MFP_CFG_LPM(GPIO80, AF4, PULL_HIGH) + +#define GPIO5_MMC2_DAT0 MFP_CFG_LPM(GPIO5, AF2, PULL_HIGH) +#define GPIO6_MMC2_DAT1 MFP_CFG_LPM(GPIO6, AF2, PULL_HIGH) +#define GPIO7_MMC2_DAT2 MFP_CFG_LPM(GPIO7, AF2, PULL_HIGH) +#define GPIO8_MMC2_DAT3 MFP_CFG_LPM(GPIO8, AF2, PULL_HIGH) +#define GPIO24_MMC2_DAT0 MFP_CFG_LPM(GPIO24, AF4, PULL_HIGH) +#define GPIO75_MMC2_DAT0 MFP_CFG_LPM(GPIO75, AF4, PULL_HIGH) +#define GPIO25_MMC2_DAT1 MFP_CFG_LPM(GPIO25, AF4, PULL_HIGH) +#define GPIO76_MMC2_DAT1 MFP_CFG_LPM(GPIO76, AF4, PULL_HIGH) +#define GPIO26_MMC2_DAT2 MFP_CFG_LPM(GPIO26, AF4, PULL_HIGH) +#define GPIO77_MMC2_DAT2 MFP_CFG_LPM(GPIO77, AF4, PULL_HIGH) +#define GPIO27_MMC2_DAT3 MFP_CFG_LPM(GPIO27, AF4, PULL_HIGH) +#define GPIO78_MMC2_DAT3 MFP_CFG_LPM(GPIO78, AF4, PULL_HIGH) + +/* 1-Wire */ +#define GPIO14_ONE_WIRE MFP_CFG_LPM(GPIO14, AF5, FLOAT) +#define GPIO0_2_ONE_WIRE MFP_CFG_LPM(GPIO0_2, AF2, FLOAT) + +/* SSP1 */ +#define GPIO87_SSP1_EXTCLK MFP_CFG(GPIO87, AF1) +#define GPIO88_SSP1_SYSCLK MFP_CFG(GPIO88, AF1) +#define GPIO83_SSP1_SCLK MFP_CFG(GPIO83, AF1) +#define GPIO84_SSP1_SFRM MFP_CFG(GPIO84, AF1) +#define GPIO85_SSP1_RXD MFP_CFG(GPIO85, AF6) +#define GPIO85_SSP1_TXD MFP_CFG(GPIO85, AF1) +#define GPIO86_SSP1_RXD MFP_CFG(GPIO86, AF1) +#define GPIO86_SSP1_TXD MFP_CFG(GPIO86, AF6) + +/* SSP2 */ +#define GPIO39_SSP2_EXTCLK MFP_CFG(GPIO39, AF2) +#define GPIO40_SSP2_SYSCLK MFP_CFG(GPIO40, AF2) +#define GPIO12_SSP2_SCLK MFP_CFG(GPIO12, AF2) +#define GPIO35_SSP2_SCLK MFP_CFG(GPIO35, AF2) +#define GPIO36_SSP2_SFRM MFP_CFG(GPIO36, AF2) +#define GPIO37_SSP2_RXD MFP_CFG(GPIO37, AF5) +#define GPIO37_SSP2_TXD MFP_CFG(GPIO37, AF2) +#define GPIO38_SSP2_RXD MFP_CFG(GPIO38, AF2) +#define GPIO38_SSP2_TXD MFP_CFG(GPIO38, AF5) + +#define GPIO69_SSP3_SCLK MFP_CFG_X(GPIO69, AF2, DS08X, FLOAT) +#define GPIO70_SSP3_FRM MFP_CFG_X(GPIO70, AF2, DS08X, DRIVE_LOW) +#define GPIO89_SSP3_SCLK MFP_CFG_X(GPIO89, AF1, DS08X, FLOAT) +#define GPIO90_SSP3_FRM MFP_CFG_X(GPIO90, AF1, DS08X, DRIVE_LOW) +#define GPIO71_SSP3_RXD MFP_CFG_X(GPIO71, AF5, DS08X, FLOAT) +#define GPIO71_SSP3_TXD MFP_CFG_X(GPIO71, AF2, DS08X, DRIVE_LOW) +#define GPIO72_SSP3_RXD MFP_CFG_X(GPIO72, AF2, DS08X, FLOAT) +#define GPIO72_SSP3_TXD MFP_CFG_X(GPIO72, AF5, DS08X, DRIVE_LOW) +#define GPIO91_SSP3_RXD MFP_CFG_X(GPIO91, AF5, DS08X, FLOAT) +#define GPIO91_SSP3_TXD MFP_CFG_X(GPIO91, AF1, DS08X, DRIVE_LOW) +#define GPIO92_SSP3_RXD MFP_CFG_X(GPIO92, AF1, DS08X, FLOAT) +#define GPIO92_SSP3_TXD MFP_CFG_X(GPIO92, AF5, DS08X, DRIVE_LOW) + +#define GPIO93_SSP4_SCLK MFP_CFG_LPM(GPIO93, AF1, PULL_HIGH) +#define GPIO94_SSP4_FRM MFP_CFG_LPM(GPIO94, AF1, PULL_HIGH) +#define GPIO94_SSP4_RXD MFP_CFG_LPM(GPIO94, AF5, PULL_HIGH) +#define GPIO95_SSP4_RXD MFP_CFG_LPM(GPIO95, AF5, PULL_HIGH) +#define GPIO95_SSP4_TXD MFP_CFG_LPM(GPIO95, AF1, PULL_HIGH) +#define GPIO96_SSP4_RXD MFP_CFG_LPM(GPIO96, AF1, PULL_HIGH) +#define GPIO96_SSP4_TXD MFP_CFG_LPM(GPIO96, AF5, PULL_HIGH) + +/* UART1 */ +#define GPIO41_UART1_RXD MFP_CFG_LPM(GPIO41, AF2, FLOAT) +#define GPIO41_UART1_TXD MFP_CFG_LPM(GPIO41, AF4, FLOAT) +#define GPIO42_UART1_RXD MFP_CFG_LPM(GPIO42, AF4, FLOAT) +#define GPIO42_UART1_TXD MFP_CFG_LPM(GPIO42, AF2, FLOAT) +#define GPIO97_UART1_RXD MFP_CFG_LPM(GPIO97, AF1, FLOAT) +#define GPIO97_UART1_TXD MFP_CFG_LPM(GPIO97, AF6, FLOAT) +#define GPIO98_UART1_RXD MFP_CFG_LPM(GPIO98, AF6, FLOAT) +#define GPIO98_UART1_TXD MFP_CFG_LPM(GPIO98, AF1, FLOAT) +#define GPIO43_UART1_CTS MFP_CFG_LPM(GPIO43, AF2, FLOAT) +#define GPIO43_UART1_RTS MFP_CFG_LPM(GPIO43, AF4, FLOAT) +#define GPIO48_UART1_CTS MFP_CFG_LPM(GPIO48, AF4, FLOAT) +#define GPIO48_UART1_RTS MFP_CFG_LPM(GPIO48, AF2, FLOAT) +#define GPIO99_UART1_CTS MFP_CFG_LPM(GPIO99, AF1, FLOAT) +#define GPIO99_UART1_RTS MFP_CFG_LPM(GPIO99, AF6, FLOAT) +#define GPIO104_UART1_CTS MFP_CFG_LPM(GPIO104, AF6, FLOAT) +#define GPIO104_UART1_RTS MFP_CFG_LPM(GPIO104, AF1, FLOAT) +#define GPIO45_UART1_DTR MFP_CFG_LPM(GPIO45, AF4, FLOAT) +#define GPIO45_UART1_DSR MFP_CFG_LPM(GPIO45, AF2, FLOAT) +#define GPIO47_UART1_DTR MFP_CFG_LPM(GPIO47, AF2, FLOAT) +#define GPIO47_UART1_DSR MFP_CFG_LPM(GPIO47, AF4, FLOAT) +#define GPIO101_UART1_DTR MFP_CFG_LPM(GPIO101, AF6, FLOAT) +#define GPIO101_UART1_DSR MFP_CFG_LPM(GPIO101, AF1, FLOAT) +#define GPIO103_UART1_DTR MFP_CFG_LPM(GPIO103, AF1, FLOAT) +#define GPIO103_UART1_DSR MFP_CFG_LPM(GPIO103, AF6, FLOAT) +#define GPIO44_UART1_DCD MFP_CFG_LPM(GPIO44, AF2, FLOAT) +#define GPIO100_UART1_DCD MFP_CFG_LPM(GPIO100, AF1, FLOAT) +#define GPIO46_UART1_RI MFP_CFG_LPM(GPIO46, AF2, FLOAT) +#define GPIO102_UART1_RI MFP_CFG_LPM(GPIO102, AF1, FLOAT) + +/* UART2 */ +#define GPIO109_UART2_CTS MFP_CFG_LPM(GPIO109, AF3, FLOAT) +#define GPIO109_UART2_RTS MFP_CFG_LPM(GPIO109, AF1, FLOAT) +#define GPIO112_UART2_CTS MFP_CFG_LPM(GPIO112, AF1, FLOAT) +#define GPIO112_UART2_RTS MFP_CFG_LPM(GPIO112, AF3, FLOAT) +#define GPIO110_UART2_RXD MFP_CFG_LPM(GPIO110, AF1, FLOAT) +#define GPIO110_UART2_TXD MFP_CFG_LPM(GPIO110, AF3, FLOAT) +#define GPIO111_UART2_RXD MFP_CFG_LPM(GPIO111, AF3, FLOAT) +#define GPIO111_UART2_TXD MFP_CFG_LPM(GPIO111, AF1, FLOAT) + +/* UART3 */ +#define GPIO89_UART3_CTS MFP_CFG_LPM(GPIO89, AF2, FLOAT) +#define GPIO89_UART3_RTS MFP_CFG_LPM(GPIO89, AF4, FLOAT) +#define GPIO90_UART3_CTS MFP_CFG_LPM(GPIO90, AF4, FLOAT) +#define GPIO90_UART3_RTS MFP_CFG_LPM(GPIO90, AF2, FLOAT) +#define GPIO105_UART3_CTS MFP_CFG_LPM(GPIO105, AF1, FLOAT) +#define GPIO105_UART3_RTS MFP_CFG_LPM(GPIO105, AF3, FLOAT) +#define GPIO106_UART3_CTS MFP_CFG_LPM(GPIO106, AF3, FLOAT) +#define GPIO106_UART3_RTS MFP_CFG_LPM(GPIO106, AF1, FLOAT) +#define GPIO30_UART3_RXD MFP_CFG_LPM(GPIO30, AF2, FLOAT) +#define GPIO30_UART3_TXD MFP_CFG_LPM(GPIO30, AF6, FLOAT) +#define GPIO31_UART3_RXD MFP_CFG_LPM(GPIO31, AF6, FLOAT) +#define GPIO31_UART3_TXD MFP_CFG_LPM(GPIO31, AF2, FLOAT) +#define GPIO91_UART3_RXD MFP_CFG_LPM(GPIO91, AF4, FLOAT) +#define GPIO91_UART3_TXD MFP_CFG_LPM(GPIO91, AF2, FLOAT) +#define GPIO92_UART3_RXD MFP_CFG_LPM(GPIO92, AF2, FLOAT) +#define GPIO92_UART3_TXD MFP_CFG_LPM(GPIO92, AF4, FLOAT) +#define GPIO107_UART3_RXD MFP_CFG_LPM(GPIO107, AF3, FLOAT) +#define GPIO107_UART3_TXD MFP_CFG_LPM(GPIO107, AF1, FLOAT) +#define GPIO108_UART3_RXD MFP_CFG_LPM(GPIO108, AF1, FLOAT) +#define GPIO108_UART3_TXD MFP_CFG_LPM(GPIO108, AF3, FLOAT) + + +/* USB 2.0 UTMI */ +#define GPIO10_UTM_CLK MFP_CFG(GPIO10, AF1) +#define GPIO36_U2D_RXERROR MFP_CFG(GPIO36, AF3) +#define GPIO60_U2D_RXERROR MFP_CFG(GPIO60, AF1) +#define GPIO87_U2D_RXERROR MFP_CFG(GPIO87, AF5) +#define GPIO34_UTM_RXVALID MFP_CFG(GPIO34, AF3) +#define GPIO58_UTM_RXVALID MFP_CFG(GPIO58, AF2) +#define GPIO85_UTM_RXVALID MFP_CFG(GPIO85, AF5) +#define GPIO35_UTM_RXACTIVE MFP_CFG(GPIO35, AF3) +#define GPIO59_UTM_RXACTIVE MFP_CFG(GPIO59, AF1) +#define GPIO86_UTM_RXACTIVE MFP_CFG(GPIO86, AF5) +#define GPIO73_UTM_TXREADY MFP_CFG(GPIO73, AF1) +#define GPIO68_UTM_LINESTATE_0 MFP_CFG(GPIO68, AF3) +#define GPIO90_UTM_LINESTATE_0 MFP_CFG(GPIO90, AF3) +#define GPIO102_UTM_LINESTATE_0 MFP_CFG(GPIO102, AF3) +#define GPIO107_UTM_LINESTATE_0 MFP_CFG(GPIO107, AF4) +#define GPIO69_UTM_LINESTATE_1 MFP_CFG(GPIO69, AF3) +#define GPIO91_UTM_LINESTATE_1 MFP_CFG(GPIO91, AF3) +#define GPIO103_UTM_LINESTATE_1 MFP_CFG(GPIO103, AF3) + +#define GPIO41_U2D_PHYDATA_0 MFP_CFG(GPIO41, AF3) +#define GPIO42_U2D_PHYDATA_1 MFP_CFG(GPIO42, AF3) +#define GPIO43_U2D_PHYDATA_2 MFP_CFG(GPIO43, AF3) +#define GPIO44_U2D_PHYDATA_3 MFP_CFG(GPIO44, AF3) +#define GPIO45_U2D_PHYDATA_4 MFP_CFG(GPIO45, AF3) +#define GPIO46_U2D_PHYDATA_5 MFP_CFG(GPIO46, AF3) +#define GPIO47_U2D_PHYDATA_6 MFP_CFG(GPIO47, AF3) +#define GPIO48_U2D_PHYDATA_7 MFP_CFG(GPIO48, AF3) + +#define GPIO49_U2D_PHYDATA_0 MFP_CFG(GPIO49, AF3) +#define GPIO50_U2D_PHYDATA_1 MFP_CFG(GPIO50, AF3) +#define GPIO51_U2D_PHYDATA_2 MFP_CFG(GPIO51, AF3) +#define GPIO52_U2D_PHYDATA_3 MFP_CFG(GPIO52, AF3) +#define GPIO53_U2D_PHYDATA_4 MFP_CFG(GPIO53, AF3) +#define GPIO54_U2D_PHYDATA_5 MFP_CFG(GPIO54, AF3) +#define GPIO55_U2D_PHYDATA_6 MFP_CFG(GPIO55, AF3) +#define GPIO56_U2D_PHYDATA_7 MFP_CFG(GPIO56, AF3) + +#define GPIO37_U2D_OPMODE0 MFP_CFG(GPIO37, AF4) +#define GPIO61_U2D_OPMODE0 MFP_CFG(GPIO61, AF2) +#define GPIO88_U2D_OPMODE0 MFP_CFG(GPIO88, AF7) + +#define GPIO38_U2D_OPMODE1 MFP_CFG(GPIO38, AF4) +#define GPIO62_U2D_OPMODE1 MFP_CFG(GPIO62, AF2) +#define GPIO104_U2D_OPMODE1 MFP_CFG(GPIO104, AF4) +#define GPIO108_U2D_OPMODE1 MFP_CFG(GPIO108, AF5) + +#define GPIO74_U2D_RESET MFP_CFG(GPIO74, AF1) +#define GPIO93_U2D_RESET MFP_CFG(GPIO93, AF2) +#define GPIO98_U2D_RESET MFP_CFG(GPIO98, AF3) + +#define GPIO67_U2D_SUSPEND MFP_CFG(GPIO67, AF3) +#define GPIO96_U2D_SUSPEND MFP_CFG(GPIO96, AF2) +#define GPIO101_U2D_SUSPEND MFP_CFG(GPIO101, AF3) + +#define GPIO66_U2D_TERM_SEL MFP_CFG(GPIO66, AF5) +#define GPIO95_U2D_TERM_SEL MFP_CFG(GPIO95, AF3) +#define GPIO97_U2D_TERM_SEL MFP_CFG(GPIO97, AF7) +#define GPIO100_U2D_TERM_SEL MFP_CFG(GPIO100, AF5) + +#define GPIO39_U2D_TXVALID MFP_CFG(GPIO39, AF4) +#define GPIO70_U2D_TXVALID MFP_CFG(GPIO70, AF5) +#define GPIO83_U2D_TXVALID MFP_CFG(GPIO83, AF7) + +#define GPIO65_U2D_XCVR_SEL MFP_CFG(GPIO65, AF5) +#define GPIO94_U2D_XCVR_SEL MFP_CFG(GPIO94, AF3) +#define GPIO99_U2D_XCVR_SEL MFP_CFG(GPIO99, AF5) + +/* USB Host 1.1 */ +#define GPIO2_2_USBH_PEN MFP_CFG(GPIO2_2, AF1) +#define GPIO3_2_USBH_PWR MFP_CFG(GPIO3_2, AF1) + +/* USB P2 */ +#define GPIO97_USB_P2_2 MFP_CFG(GPIO97, AF2) +#define GPIO97_USB_P2_6 MFP_CFG(GPIO97, AF4) +#define GPIO98_USB_P2_2 MFP_CFG(GPIO98, AF4) +#define GPIO98_USB_P2_6 MFP_CFG(GPIO98, AF2) +#define GPIO99_USB_P2_1 MFP_CFG(GPIO99, AF2) +#define GPIO100_USB_P2_4 MFP_CFG(GPIO100, AF2) +#define GPIO101_USB_P2_8 MFP_CFG(GPIO101, AF2) +#define GPIO102_USB_P2_3 MFP_CFG(GPIO102, AF2) +#define GPIO103_USB_P2_5 MFP_CFG(GPIO103, AF2) +#define GPIO104_USB_P2_7 MFP_CFG(GPIO104, AF2) + +/* USB P3 */ +#define GPIO75_USB_P3_1 MFP_CFG(GPIO75, AF2) +#define GPIO76_USB_P3_2 MFP_CFG(GPIO76, AF2) +#define GPIO77_USB_P3_3 MFP_CFG(GPIO77, AF2) +#define GPIO78_USB_P3_4 MFP_CFG(GPIO78, AF2) +#define GPIO79_USB_P3_5 MFP_CFG(GPIO79, AF2) +#define GPIO80_USB_P3_6 MFP_CFG(GPIO80, AF2) + +#define GPIO13_CHOUT0 MFP_CFG(GPIO13, AF6) +#define GPIO14_CHOUT1 MFP_CFG(GPIO14, AF6) + +#define GPIO2_RDY MFP_CFG(GPIO2, AF1) +#define GPIO5_NPIOR MFP_CFG(GPIO5, AF3) + +#define GPIO11_PWM0_OUT MFP_CFG(GPIO11, AF1) +#define GPIO12_PWM1_OUT MFP_CFG(GPIO12, AF1) +#define GPIO13_PWM2_OUT MFP_CFG(GPIO13, AF1) +#define GPIO14_PWM3_OUT MFP_CFG(GPIO14, AF1) + +#endif /* __ASM_ARCH_MFP_PXA320_H */ diff --git a/arch/arm/mach-pxa/include/mach/mfp-pxa3xx.h b/arch/arm/mach-pxa/include/mach/mfp-pxa3xx.h new file mode 100644 index 00000000000..1f6b35c015d --- /dev/null +++ b/arch/arm/mach-pxa/include/mach/mfp-pxa3xx.h @@ -0,0 +1,252 @@ +#ifndef __ASM_ARCH_MFP_PXA3XX_H +#define __ASM_ARCH_MFP_PXA3XX_H + +#define MFPR_BASE (0x40e10000) +#define MFPR_SIZE (PAGE_SIZE) + +/* MFPR register bit definitions */ +#define MFPR_PULL_SEL (0x1 << 15) +#define MFPR_PULLUP_EN (0x1 << 14) +#define MFPR_PULLDOWN_EN (0x1 << 13) +#define MFPR_SLEEP_SEL (0x1 << 9) +#define MFPR_SLEEP_OE_N (0x1 << 7) +#define MFPR_EDGE_CLEAR (0x1 << 6) +#define MFPR_EDGE_FALL_EN (0x1 << 5) +#define MFPR_EDGE_RISE_EN (0x1 << 4) + +#define MFPR_SLEEP_DATA(x) ((x) << 8) +#define MFPR_DRIVE(x) (((x) & 0x7) << 10) +#define MFPR_AF_SEL(x) (((x) & 0x7) << 0) + +#define MFPR_EDGE_NONE (0) +#define MFPR_EDGE_RISE (MFPR_EDGE_RISE_EN) +#define MFPR_EDGE_FALL (MFPR_EDGE_FALL_EN) +#define MFPR_EDGE_BOTH (MFPR_EDGE_RISE | MFPR_EDGE_FALL) + +/* + * Table that determines the low power modes outputs, with actual settings + * used in parentheses for don't-care values. Except for the float output, + * the configured driven and pulled levels match, so if there is a need for + * non-LPM pulled output, the same configuration could probably be used. + * + * Output value sleep_oe_n sleep_data pullup_en pulldown_en pull_sel + * (bit 7) (bit 8) (bit 14) (bit 13) (bit 15) + * + * Input 0 X(0) X(0) X(0) 0 + * Drive 0 0 0 0 X(1) 0 + * Drive 1 0 1 X(1) 0 0 + * Pull hi (1) 1 X(1) 1 0 0 + * Pull lo (0) 1 X(0) 0 1 0 + * Z (float) 1 X(0) 0 0 0 + */ +#define MFPR_LPM_INPUT (0) +#define MFPR_LPM_DRIVE_LOW (MFPR_SLEEP_DATA(0) | MFPR_PULLDOWN_EN) +#define MFPR_LPM_DRIVE_HIGH (MFPR_SLEEP_DATA(1) | MFPR_PULLUP_EN) +#define MFPR_LPM_PULL_LOW (MFPR_LPM_DRIVE_LOW | MFPR_SLEEP_OE_N) +#define MFPR_LPM_PULL_HIGH (MFPR_LPM_DRIVE_HIGH | MFPR_SLEEP_OE_N) +#define MFPR_LPM_FLOAT (MFPR_SLEEP_OE_N) +#define MFPR_LPM_MASK (0xe080) + +/* + * The pullup and pulldown state of the MFP pin at run mode is by default + * determined by the selected alternate function. In case that some buggy + * devices need to override this default behavior, the definitions below + * indicates the setting of corresponding MFPR bits + * + * Definition pull_sel pullup_en pulldown_en + * MFPR_PULL_NONE 0 0 0 + * MFPR_PULL_LOW 1 0 1 + * MFPR_PULL_HIGH 1 1 0 + * MFPR_PULL_BOTH 1 1 1 + */ +#define MFPR_PULL_NONE (0) +#define MFPR_PULL_LOW (MFPR_PULL_SEL | MFPR_PULLDOWN_EN) +#define MFPR_PULL_BOTH (MFPR_PULL_LOW | MFPR_PULLUP_EN) +#define MFPR_PULL_HIGH (MFPR_PULL_SEL | MFPR_PULLUP_EN) + +/* PXA3xx common MFP configurations - processor specific ones defined + * in mfp-pxa300.h and mfp-pxa320.h + */ +#define GPIO0_GPIO MFP_CFG(GPIO0, AF0) +#define GPIO1_GPIO MFP_CFG(GPIO1, AF0) +#define GPIO2_GPIO MFP_CFG(GPIO2, AF0) +#define GPIO3_GPIO MFP_CFG(GPIO3, AF0) +#define GPIO4_GPIO MFP_CFG(GPIO4, AF0) +#define GPIO5_GPIO MFP_CFG(GPIO5, AF0) +#define GPIO6_GPIO MFP_CFG(GPIO6, AF0) +#define GPIO7_GPIO MFP_CFG(GPIO7, AF0) +#define GPIO8_GPIO MFP_CFG(GPIO8, AF0) +#define GPIO9_GPIO MFP_CFG(GPIO9, AF0) +#define GPIO10_GPIO MFP_CFG(GPIO10, AF0) +#define GPIO11_GPIO MFP_CFG(GPIO11, AF0) +#define GPIO12_GPIO MFP_CFG(GPIO12, AF0) +#define GPIO13_GPIO MFP_CFG(GPIO13, AF0) +#define GPIO14_GPIO MFP_CFG(GPIO14, AF0) +#define GPIO15_GPIO MFP_CFG(GPIO15, AF0) +#define GPIO16_GPIO MFP_CFG(GPIO16, AF0) +#define GPIO17_GPIO MFP_CFG(GPIO17, AF0) +#define GPIO18_GPIO MFP_CFG(GPIO18, AF0) +#define GPIO19_GPIO MFP_CFG(GPIO19, AF0) +#define GPIO20_GPIO MFP_CFG(GPIO20, AF0) +#define GPIO21_GPIO MFP_CFG(GPIO21, AF0) +#define GPIO22_GPIO MFP_CFG(GPIO22, AF0) +#define GPIO23_GPIO MFP_CFG(GPIO23, AF0) +#define GPIO24_GPIO MFP_CFG(GPIO24, AF0) +#define GPIO25_GPIO MFP_CFG(GPIO25, AF0) +#define GPIO26_GPIO MFP_CFG(GPIO26, AF0) +#define GPIO27_GPIO MFP_CFG(GPIO27, AF0) +#define GPIO28_GPIO MFP_CFG(GPIO28, AF0) +#define GPIO29_GPIO MFP_CFG(GPIO29, AF0) +#define GPIO30_GPIO MFP_CFG(GPIO30, AF0) +#define GPIO31_GPIO MFP_CFG(GPIO31, AF0) +#define GPIO32_GPIO MFP_CFG(GPIO32, AF0) +#define GPIO33_GPIO MFP_CFG(GPIO33, AF0) +#define GPIO34_GPIO MFP_CFG(GPIO34, AF0) +#define GPIO35_GPIO MFP_CFG(GPIO35, AF0) +#define GPIO36_GPIO MFP_CFG(GPIO36, AF0) +#define GPIO37_GPIO MFP_CFG(GPIO37, AF0) +#define GPIO38_GPIO MFP_CFG(GPIO38, AF0) +#define GPIO39_GPIO MFP_CFG(GPIO39, AF0) +#define GPIO40_GPIO MFP_CFG(GPIO40, AF0) +#define GPIO41_GPIO MFP_CFG(GPIO41, AF0) +#define GPIO42_GPIO MFP_CFG(GPIO42, AF0) +#define GPIO43_GPIO MFP_CFG(GPIO43, AF0) +#define GPIO44_GPIO MFP_CFG(GPIO44, AF0) +#define GPIO45_GPIO MFP_CFG(GPIO45, AF0) + +#define GPIO47_GPIO MFP_CFG(GPIO47, AF0) +#define GPIO48_GPIO MFP_CFG(GPIO48, AF0) + +#define GPIO53_GPIO MFP_CFG(GPIO53, AF0) +#define GPIO54_GPIO MFP_CFG(GPIO54, AF0) +#define GPIO55_GPIO MFP_CFG(GPIO55, AF0) + +#define GPIO57_GPIO MFP_CFG(GPIO57, AF0) + +#define GPIO63_GPIO MFP_CFG(GPIO63, AF0) +#define GPIO64_GPIO MFP_CFG(GPIO64, AF0) +#define GPIO65_GPIO MFP_CFG(GPIO65, AF0) +#define GPIO66_GPIO MFP_CFG(GPIO66, AF0) +#define GPIO67_GPIO MFP_CFG(GPIO67, AF0) +#define GPIO68_GPIO MFP_CFG(GPIO68, AF0) +#define GPIO69_GPIO MFP_CFG(GPIO69, AF0) +#define GPIO70_GPIO MFP_CFG(GPIO70, AF0) +#define GPIO71_GPIO MFP_CFG(GPIO71, AF0) +#define GPIO72_GPIO MFP_CFG(GPIO72, AF0) +#define GPIO73_GPIO MFP_CFG(GPIO73, AF0) +#define GPIO74_GPIO MFP_CFG(GPIO74, AF0) +#define GPIO75_GPIO MFP_CFG(GPIO75, AF0) +#define GPIO76_GPIO MFP_CFG(GPIO76, AF0) +#define GPIO77_GPIO MFP_CFG(GPIO77, AF0) +#define GPIO78_GPIO MFP_CFG(GPIO78, AF0) +#define GPIO79_GPIO MFP_CFG(GPIO79, AF0) +#define GPIO80_GPIO MFP_CFG(GPIO80, AF0) +#define GPIO81_GPIO MFP_CFG(GPIO81, AF0) +#define GPIO82_GPIO MFP_CFG(GPIO82, AF0) +#define GPIO83_GPIO MFP_CFG(GPIO83, AF0) +#define GPIO84_GPIO MFP_CFG(GPIO84, AF0) +#define GPIO85_GPIO MFP_CFG(GPIO85, AF0) +#define GPIO86_GPIO MFP_CFG(GPIO86, AF0) +#define GPIO87_GPIO MFP_CFG(GPIO87, AF0) +#define GPIO88_GPIO MFP_CFG(GPIO88, AF0) +#define GPIO89_GPIO MFP_CFG(GPIO89, AF0) +#define GPIO90_GPIO MFP_CFG(GPIO90, AF0) +#define GPIO91_GPIO MFP_CFG(GPIO91, AF0) +#define GPIO92_GPIO MFP_CFG(GPIO92, AF0) +#define GPIO93_GPIO MFP_CFG(GPIO93, AF0) +#define GPIO94_GPIO MFP_CFG(GPIO94, AF0) +#define GPIO95_GPIO MFP_CFG(GPIO95, AF0) +#define GPIO96_GPIO MFP_CFG(GPIO96, AF0) +#define GPIO97_GPIO MFP_CFG(GPIO97, AF0) +#define GPIO98_GPIO MFP_CFG(GPIO98, AF0) +#define GPIO99_GPIO MFP_CFG(GPIO99, AF0) +#define GPIO100_GPIO MFP_CFG(GPIO100, AF0) +#define GPIO101_GPIO MFP_CFG(GPIO101, AF0) +#define GPIO102_GPIO MFP_CFG(GPIO102, AF0) +#define GPIO103_GPIO MFP_CFG(GPIO103, AF0) +#define GPIO104_GPIO MFP_CFG(GPIO104, AF0) +#define GPIO105_GPIO MFP_CFG(GPIO105, AF0) +#define GPIO106_GPIO MFP_CFG(GPIO106, AF0) +#define GPIO107_GPIO MFP_CFG(GPIO107, AF0) +#define GPIO108_GPIO MFP_CFG(GPIO108, AF0) +#define GPIO109_GPIO MFP_CFG(GPIO109, AF0) +#define GPIO110_GPIO MFP_CFG(GPIO110, AF0) +#define GPIO111_GPIO MFP_CFG(GPIO111, AF0) +#define GPIO112_GPIO MFP_CFG(GPIO112, AF0) +#define GPIO113_GPIO MFP_CFG(GPIO113, AF0) +#define GPIO114_GPIO MFP_CFG(GPIO114, AF0) +#define GPIO115_GPIO MFP_CFG(GPIO115, AF0) +#define GPIO116_GPIO MFP_CFG(GPIO116, AF0) +#define GPIO117_GPIO MFP_CFG(GPIO117, AF0) +#define GPIO118_GPIO MFP_CFG(GPIO118, AF0) +#define GPIO119_GPIO MFP_CFG(GPIO119, AF0) +#define GPIO120_GPIO MFP_CFG(GPIO120, AF0) +#define GPIO121_GPIO MFP_CFG(GPIO121, AF0) +#define GPIO122_GPIO MFP_CFG(GPIO122, AF0) +#define GPIO123_GPIO MFP_CFG(GPIO123, AF0) +#define GPIO124_GPIO MFP_CFG(GPIO124, AF0) +#define GPIO125_GPIO MFP_CFG(GPIO125, AF0) +#define GPIO126_GPIO MFP_CFG(GPIO126, AF0) +#define GPIO127_GPIO MFP_CFG(GPIO127, AF0) + +#define GPIO0_2_GPIO MFP_CFG(GPIO0_2, AF0) +#define GPIO1_2_GPIO MFP_CFG(GPIO1_2, AF0) +#define GPIO2_2_GPIO MFP_CFG(GPIO2_2, AF0) +#define GPIO3_2_GPIO MFP_CFG(GPIO3_2, AF0) +#define GPIO4_2_GPIO MFP_CFG(GPIO4_2, AF0) +#define GPIO5_2_GPIO MFP_CFG(GPIO5_2, AF0) +#define GPIO6_2_GPIO MFP_CFG(GPIO6_2, AF0) + +/* + * each MFP pin will have a MFPR register, since the offset of the + * register varies between processors, the processor specific code + * should initialize the pin offsets by pxa3xx_mfp_init_addr() + * + * pxa3xx_mfp_init_addr - accepts a table of "pxa3xx_mfp_addr_map" + * structure, which represents a range of MFP pins from "start" to + * "end", with the offset begining at "offset", to define a single + * pin, let "end" = -1 + * + * use + * + * MFP_ADDR_X() to define a range of pins + * MFP_ADDR() to define a single pin + * MFP_ADDR_END to signal the end of pin offset definitions + */ +struct pxa3xx_mfp_addr_map { + unsigned int start; + unsigned int end; + unsigned long offset; +}; + +#define MFP_ADDR_X(start, end, offset) \ + { MFP_PIN_##start, MFP_PIN_##end, offset } + +#define MFP_ADDR(pin, offset) \ + { MFP_PIN_##pin, -1, offset } + +#define MFP_ADDR_END { MFP_PIN_INVALID, 0 } + +/* + * pxa3xx_mfp_read()/pxa3xx_mfp_write() - for direct read/write access + * to the MFPR register + */ +unsigned long pxa3xx_mfp_read(int mfp); +void pxa3xx_mfp_write(int mfp, unsigned long mfpr_val); + +/* + * pxa3xx_mfp_config - configure the MFPR registers + * + * used by board specific initialization code + */ +void pxa3xx_mfp_config(unsigned long *mfp_cfgs, int num); + +/* + * pxa3xx_mfp_init_addr() - initialize the mapping between mfp pin + * index and MFPR register offset + * + * used by processor specific code + */ +void __init pxa3xx_mfp_init_addr(struct pxa3xx_mfp_addr_map *); +void __init pxa3xx_init_mfp(void); +#endif /* __ASM_ARCH_MFP_PXA3XX_H */ diff --git a/arch/arm/mach-pxa/include/mach/mfp-pxa930.h b/arch/arm/mach-pxa/include/mach/mfp-pxa930.h new file mode 100644 index 00000000000..fabd9b4df82 --- /dev/null +++ b/arch/arm/mach-pxa/include/mach/mfp-pxa930.h @@ -0,0 +1,491 @@ +/* + * arch/arm/mach-pxa/include/mach/mfp-pxa930.h + * + * PXA930 specific MFP configuration definitions + * + * Copyright (C) 2007-2008 Marvell International Ltd. + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ + +#ifndef __ASM_ARCH_MFP_PXA9xx_H +#define __ASM_ARCH_MFP_PXA9xx_H + +#include <mach/mfp.h> +#include <mach/mfp-pxa3xx.h> + +/* GPIO */ +#define GPIO46_GPIO MFP_CFG(GPIO46, AF0) +#define GPIO49_GPIO MFP_CFG(GPIO49, AF0) +#define GPIO50_GPIO MFP_CFG(GPIO50, AF0) +#define GPIO51_GPIO MFP_CFG(GPIO51, AF0) +#define GPIO52_GPIO MFP_CFG(GPIO52, AF0) +#define GPIO56_GPIO MFP_CFG(GPIO56, AF0) +#define GPIO58_GPIO MFP_CFG(GPIO58, AF0) +#define GPIO59_GPIO MFP_CFG(GPIO59, AF0) +#define GPIO60_GPIO MFP_CFG(GPIO60, AF0) +#define GPIO61_GPIO MFP_CFG(GPIO61, AF0) +#define GPIO62_GPIO MFP_CFG(GPIO62, AF0) + +#define GSIM_UCLK_GPIO_79 MFP_CFG(GSIM_UCLK, AF0) +#define GSIM_UIO_GPIO_80 MFP_CFG(GSIM_UIO, AF0) +#define GSIM_nURST_GPIO_81 MFP_CFG(GSIM_nURST, AF0) +#define GSIM_UDET_GPIO_82 MFP_CFG(GSIM_UDET, AF0) + +#define DF_IO15_GPIO_28 MFP_CFG(DF_IO15, AF0) +#define DF_IO14_GPIO_29 MFP_CFG(DF_IO14, AF0) +#define DF_IO13_GPIO_30 MFP_CFG(DF_IO13, AF0) +#define DF_IO12_GPIO_31 MFP_CFG(DF_IO12, AF0) +#define DF_IO11_GPIO_32 MFP_CFG(DF_IO11, AF0) +#define DF_IO10_GPIO_33 MFP_CFG(DF_IO10, AF0) +#define DF_IO9_GPIO_34 MFP_CFG(DF_IO9, AF0) +#define DF_IO8_GPIO_35 MFP_CFG(DF_IO8, AF0) +#define DF_IO7_GPIO_36 MFP_CFG(DF_IO7, AF0) +#define DF_IO6_GPIO_37 MFP_CFG(DF_IO6, AF0) +#define DF_IO5_GPIO_38 MFP_CFG(DF_IO5, AF0) +#define DF_IO4_GPIO_39 MFP_CFG(DF_IO4, AF0) +#define DF_IO3_GPIO_40 MFP_CFG(DF_IO3, AF0) +#define DF_IO2_GPIO_41 MFP_CFG(DF_IO2, AF0) +#define DF_IO1_GPIO_42 MFP_CFG(DF_IO1, AF0) +#define DF_IO0_GPIO_43 MFP_CFG(DF_IO0, AF0) +#define DF_nCS0_GPIO_44 MFP_CFG(DF_nCS0, AF0) +#define DF_nCS1_GPIO_45 MFP_CFG(DF_nCS1, AF0) +#define DF_nWE_GPIO_46 MFP_CFG(DF_nWE, AF0) +#define DF_nRE_nOE_GPIO_47 MFP_CFG(DF_nRE_nOE, AF0) +#define DF_CLE_nOE_GPIO_48 MFP_CFG(DF_CLE_nOE, AF0) +#define DF_nADV1_ALE_GPIO_49 MFP_CFG(DF_nADV1_ALE, AF0) +#define DF_nADV2_ALE_GPIO_50 MFP_CFG(DF_nADV2_ALE, AF0) +#define DF_INT_RnB_GPIO_51 MFP_CFG(DF_INT_RnB, AF0) +#define DF_SCLK_E_GPIO_52 MFP_CFG(DF_SCLK_E, AF0) + +#define DF_ADDR0_GPIO_53 MFP_CFG(DF_ADDR0, AF0) +#define DF_ADDR1_GPIO_54 MFP_CFG(DF_ADDR1, AF0) +#define DF_ADDR2_GPIO_55 MFP_CFG(DF_ADDR2, AF0) +#define DF_ADDR3_GPIO_56 MFP_CFG(DF_ADDR3, AF0) +#define nXCVREN_GPIO_57 MFP_CFG(nXCVREN, AF0) +#define nLUA_GPIO_58 MFP_CFG(nLUA, AF0) +#define nLLA_GPIO_59 MFP_CFG(nLLA, AF0) +#define nBE0_GPIO_60 MFP_CFG(nBE0, AF0) +#define nBE1_GPIO_61 MFP_CFG(nBE1, AF0) +#define RDY_GPIO_62 MFP_CFG(RDY, AF0) + +/* Chip Select */ +#define DF_nCS0_nCS2 MFP_CFG_LPM(DF_nCS0, AF3, PULL_HIGH) +#define DF_nCS1_nCS3 MFP_CFG_LPM(DF_nCS1, AF3, PULL_HIGH) + +/* AC97 */ +#define GPIO83_BAC97_SYSCLK MFP_CFG(GPIO83, AF3) +#define GPIO84_BAC97_SDATA_IN0 MFP_CFG(GPIO84, AF3) +#define GPIO85_BAC97_BITCLK MFP_CFG(GPIO85, AF3) +#define GPIO86_BAC97_nRESET MFP_CFG(GPIO86, AF3) +#define GPIO87_BAC97_SYNC MFP_CFG(GPIO87, AF3) +#define GPIO88_BAC97_SDATA_OUT MFP_CFG(GPIO88, AF3) + +/* I2C */ +#define GPIO39_CI2C_SCL MFP_CFG_LPM(GPIO39, AF3, PULL_HIGH) +#define GPIO40_CI2C_SDA MFP_CFG_LPM(GPIO40, AF3, PULL_HIGH) + +#define GPIO51_CI2C_SCL MFP_CFG_LPM(GPIO51, AF3, PULL_HIGH) +#define GPIO52_CI2C_SDA MFP_CFG_LPM(GPIO52, AF3, PULL_HIGH) + +#define GPIO63_CI2C_SCL MFP_CFG_LPM(GPIO63, AF4, PULL_HIGH) +#define GPIO64_CI2C_SDA MFP_CFG_LPM(GPIO64, AF4, PULL_HIGH) + +#define GPIO77_CI2C_SCL MFP_CFG_LPM(GPIO77, AF2, PULL_HIGH) +#define GPIO78_CI2C_SDA MFP_CFG_LPM(GPIO78, AF2, PULL_HIGH) + +#define GPIO89_CI2C_SCL MFP_CFG_LPM(GPIO89, AF1, PULL_HIGH) +#define GPIO90_CI2C_SDA MFP_CFG_LPM(GPIO90, AF1, PULL_HIGH) + +#define GPIO95_CI2C_SCL MFP_CFG_LPM(GPIO95, AF1, PULL_HIGH) +#define GPIO96_CI2C_SDA MFP_CFG_LPM(GPIO96, AF1, PULL_HIGH) + +#define GPIO97_CI2C_SCL MFP_CFG_LPM(GPIO97, AF3, PULL_HIGH) +#define GPIO98_CI2C_SDA MFP_CFG_LPM(GPIO98, AF3, PULL_HIGH) + +/* QCI */ +#define GPIO63_CI_DD_9 MFP_CFG_LPM(GPIO63, AF1, PULL_LOW) +#define GPIO64_CI_DD_8 MFP_CFG_LPM(GPIO64, AF1, PULL_LOW) +#define GPIO65_CI_DD_7 MFP_CFG_LPM(GPIO65, AF1, PULL_LOW) +#define GPIO66_CI_DD_6 MFP_CFG_LPM(GPIO66, AF1, PULL_LOW) +#define GPIO67_CI_DD_5 MFP_CFG_LPM(GPIO67, AF1, PULL_LOW) +#define GPIO68_CI_DD_4 MFP_CFG_LPM(GPIO68, AF1, PULL_LOW) +#define GPIO69_CI_DD_3 MFP_CFG_LPM(GPIO69, AF1, PULL_LOW) +#define GPIO70_CI_DD_2 MFP_CFG_LPM(GPIO70, AF1, PULL_LOW) +#define GPIO71_CI_DD_1 MFP_CFG_LPM(GPIO71, AF1, PULL_LOW) +#define GPIO72_CI_DD_0 MFP_CFG_LPM(GPIO72, AF1, PULL_LOW) +#define GPIO73_CI_HSYNC MFP_CFG_LPM(GPIO73, AF1, PULL_LOW) +#define GPIO74_CI_VSYNC MFP_CFG_LPM(GPIO74, AF1, PULL_LOW) +#define GPIO75_CI_MCLK MFP_CFG_LPM(GPIO75, AF1, PULL_LOW) +#define GPIO76_CI_PCLK MFP_CFG_LPM(GPIO76, AF1, PULL_LOW) + +/* KEYPAD */ +#define GPIO4_KP_DKIN_4 MFP_CFG_LPM(GPIO4, AF3, FLOAT) +#define GPIO5_KP_DKIN_5 MFP_CFG_LPM(GPIO5, AF3, FLOAT) +#define GPIO6_KP_DKIN_6 MFP_CFG_LPM(GPIO6, AF3, FLOAT) +#define GPIO7_KP_DKIN_7 MFP_CFG_LPM(GPIO7, AF3, FLOAT) +#define GPIO8_KP_DKIN_4 MFP_CFG_LPM(GPIO8, AF3, FLOAT) +#define GPIO9_KP_DKIN_5 MFP_CFG_LPM(GPIO9, AF3, FLOAT) +#define GPIO10_KP_DKIN_6 MFP_CFG_LPM(GPIO10, AF3, FLOAT) +#define GPIO11_KP_DKIN_7 MFP_CFG_LPM(GPIO11, AF3, FLOAT) + +#define GPIO12_KP_DKIN_0 MFP_CFG_LPM(GPIO12, AF2, FLOAT) +#define GPIO13_KP_DKIN_1 MFP_CFG_LPM(GPIO13, AF2, FLOAT) +#define GPIO14_KP_DKIN_2 MFP_CFG_LPM(GPIO14, AF2, FLOAT) +#define GPIO15_KP_DKIN_3 MFP_CFG_LPM(GPIO15, AF2, FLOAT) + +#define GPIO41_KP_DKIN_0 MFP_CFG_LPM(GPIO41, AF2, FLOAT) +#define GPIO42_KP_DKIN_1 MFP_CFG_LPM(GPIO42, AF2, FLOAT) +#define GPIO43_KP_DKIN_2 MFP_CFG_LPM(GPIO43, AF2, FLOAT) +#define GPIO44_KP_DKIN_3 MFP_CFG_LPM(GPIO44, AF2, FLOAT) +#define GPIO41_KP_DKIN_4 MFP_CFG_LPM(GPIO41, AF4, FLOAT) +#define GPIO42_KP_DKIN_5 MFP_CFG_LPM(GPIO42, AF4, FLOAT) + +#define GPIO0_KP_MKIN_0 MFP_CFG_LPM(GPIO0, AF1, FLOAT) +#define GPIO2_KP_MKIN_1 MFP_CFG_LPM(GPIO2, AF1, FLOAT) +#define GPIO4_KP_MKIN_2 MFP_CFG_LPM(GPIO4, AF1, FLOAT) +#define GPIO6_KP_MKIN_3 MFP_CFG_LPM(GPIO6, AF1, FLOAT) +#define GPIO8_KP_MKIN_4 MFP_CFG_LPM(GPIO8, AF1, FLOAT) +#define GPIO10_KP_MKIN_5 MFP_CFG_LPM(GPIO10, AF1, FLOAT) +#define GPIO12_KP_MKIN_6 MFP_CFG_LPM(GPIO12, AF1, FLOAT) +#define GPIO14_KP_MKIN_7 MFP_CFG(GPIO14, AF1) +#define GPIO35_KP_MKIN_5 MFP_CFG(GPIO35, AF4) + +#define GPIO1_KP_MKOUT_0 MFP_CFG_LPM(GPIO1, AF1, DRIVE_HIGH) +#define GPIO3_KP_MKOUT_1 MFP_CFG_LPM(GPIO3, AF1, DRIVE_HIGH) +#define GPIO5_KP_MKOUT_2 MFP_CFG_LPM(GPIO5, AF1, DRIVE_HIGH) +#define GPIO7_KP_MKOUT_3 MFP_CFG_LPM(GPIO7, AF1, DRIVE_HIGH) +#define GPIO9_KP_MKOUT_4 MFP_CFG_LPM(GPIO9, AF1, DRIVE_HIGH) +#define GPIO11_KP_MKOUT_5 MFP_CFG_LPM(GPIO11, AF1, DRIVE_HIGH) +#define GPIO13_KP_MKOUT_6 MFP_CFG_LPM(GPIO13, AF1, DRIVE_HIGH) +#define GPIO15_KP_MKOUT_7 MFP_CFG_LPM(GPIO15, AF1, DRIVE_HIGH) +#define GPIO36_KP_MKOUT_5 MFP_CFG_LPM(GPIO36, AF4, DRIVE_HIGH) + +/* LCD */ +#define GPIO17_LCD_FCLK_RD MFP_CFG(GPIO17, AF1) +#define GPIO18_LCD_LCLK_A0 MFP_CFG(GPIO18, AF1) +#define GPIO19_LCD_PCLK_WR MFP_CFG(GPIO19, AF1) +#define GPIO20_LCD_BIAS MFP_CFG(GPIO20, AF1) +#define GPIO21_LCD_CS MFP_CFG(GPIO21, AF1) +#define GPIO22_LCD_CS2 MFP_CFG(GPIO22, AF2) +#define GPIO22_LCD_VSYNC MFP_CFG(GPIO22, AF1) +#define GPIO23_LCD_DD0 MFP_CFG(GPIO23, AF1) +#define GPIO24_LCD_DD1 MFP_CFG(GPIO24, AF1) +#define GPIO25_LCD_DD2 MFP_CFG(GPIO25, AF1) +#define GPIO26_LCD_DD3 MFP_CFG(GPIO26, AF1) +#define GPIO27_LCD_DD4 MFP_CFG(GPIO27, AF1) +#define GPIO28_LCD_DD5 MFP_CFG(GPIO28, AF1) +#define GPIO29_LCD_DD6 MFP_CFG(GPIO29, AF1) +#define GPIO30_LCD_DD7 MFP_CFG(GPIO30, AF1) +#define GPIO31_LCD_DD8 MFP_CFG(GPIO31, AF1) +#define GPIO32_LCD_DD9 MFP_CFG(GPIO32, AF1) +#define GPIO33_LCD_DD10 MFP_CFG(GPIO33, AF1) +#define GPIO34_LCD_DD11 MFP_CFG(GPIO34, AF1) +#define GPIO35_LCD_DD12 MFP_CFG(GPIO35, AF1) +#define GPIO36_LCD_DD13 MFP_CFG(GPIO36, AF1) +#define GPIO37_LCD_DD14 MFP_CFG(GPIO37, AF1) +#define GPIO38_LCD_DD15 MFP_CFG(GPIO38, AF1) +#define GPIO39_LCD_DD16 MFP_CFG(GPIO39, AF1) +#define GPIO40_LCD_DD17 MFP_CFG(GPIO40, AF1) +#define GPIO41_LCD_CS2 MFP_CFG(GPIO41, AF3) +#define GPIO42_LCD_VSYNC2 MFP_CFG(GPIO42, AF3) +#define GPIO44_LCD_DD7 MFP_CFG(GPIO44, AF1) + +/* Mini-LCD */ +#define GPIO17_MLCD_FCLK MFP_CFG(GPIO17, AF3) +#define GPIO18_MLCD_LCLK MFP_CFG(GPIO18, AF3) +#define GPIO19_MLCD_PCLK MFP_CFG(GPIO19, AF3) +#define GPIO20_MLCD_BIAS MFP_CFG(GPIO20, AF3) +#define GPIO23_MLCD_DD0 MFP_CFG(GPIO23, AF3) +#define GPIO24_MLCD_DD1 MFP_CFG(GPIO24, AF3) +#define GPIO25_MLCD_DD2 MFP_CFG(GPIO25, AF3) +#define GPIO26_MLCD_DD3 MFP_CFG(GPIO26, AF3) +#define GPIO27_MLCD_DD4 MFP_CFG(GPIO27, AF3) +#define GPIO28_MLCD_DD5 MFP_CFG(GPIO28, AF3) +#define GPIO29_MLCD_DD6 MFP_CFG(GPIO29, AF3) +#define GPIO30_MLCD_DD7 MFP_CFG(GPIO30, AF3) +#define GPIO31_MLCD_DD8 MFP_CFG(GPIO31, AF3) +#define GPIO32_MLCD_DD9 MFP_CFG(GPIO32, AF3) +#define GPIO33_MLCD_DD10 MFP_CFG(GPIO33, AF3) +#define GPIO34_MLCD_DD11 MFP_CFG(GPIO34, AF3) +#define GPIO35_MLCD_DD12 MFP_CFG(GPIO35, AF3) +#define GPIO36_MLCD_DD13 MFP_CFG(GPIO36, AF3) +#define GPIO37_MLCD_DD14 MFP_CFG(GPIO37, AF3) +#define GPIO38_MLCD_DD15 MFP_CFG(GPIO38, AF3) +#define GPIO44_MLCD_DD7 MFP_CFG(GPIO44, AF5) + +/* MMC1 */ +#define GPIO10_MMC1_DAT3 MFP_CFG(GPIO10, AF4) +#define GPIO11_MMC1_DAT2 MFP_CFG(GPIO11, AF4) +#define GPIO12_MMC1_DAT1 MFP_CFG(GPIO12, AF4) +#define GPIO13_MMC1_DAT0 MFP_CFG(GPIO13, AF4) +#define GPIO14_MMC1_CMD MFP_CFG(GPIO14, AF4) +#define GPIO15_MMC1_CLK MFP_CFG(GPIO15, AF4) +#define GPIO55_MMC1_CMD MFP_CFG(GPIO55, AF3) +#define GPIO56_MMC1_CLK MFP_CFG(GPIO56, AF3) +#define GPIO57_MMC1_DAT0 MFP_CFG(GPIO57, AF3) +#define GPIO58_MMC1_DAT1 MFP_CFG(GPIO58, AF3) +#define GPIO59_MMC1_DAT2 MFP_CFG(GPIO59, AF3) +#define GPIO60_MMC1_DAT3 MFP_CFG(GPIO60, AF3) + +#define DF_ADDR0_MMC1_CLK MFP_CFG(DF_ADDR0, AF2) +#define DF_ADDR1_MMC1_CMD MFP_CFG(DF_ADDR1, AF2) +#define DF_ADDR2_MMC1_DAT0 MFP_CFG(DF_ADDR2, AF2) +#define DF_ADDR3_MMC1_DAT1 MFP_CFG(DF_ADDR3, AF3) +#define nXCVREN_MMC1_DAT2 MFP_CFG(nXCVREN, AF2) + +/* MMC2 */ +#define GPIO31_MMC2_CMD MFP_CFG(GPIO31, AF7) +#define GPIO32_MMC2_CLK MFP_CFG(GPIO32, AF7) +#define GPIO33_MMC2_DAT0 MFP_CFG(GPIO33, AF7) +#define GPIO34_MMC2_DAT1 MFP_CFG(GPIO34, AF7) +#define GPIO35_MMC2_DAT2 MFP_CFG(GPIO35, AF7) +#define GPIO36_MMC2_DAT3 MFP_CFG(GPIO36, AF7) + +#define GPIO101_MMC2_DAT3 MFP_CFG(GPIO101, AF1) +#define GPIO102_MMC2_DAT2 MFP_CFG(GPIO102, AF1) +#define GPIO103_MMC2_DAT1 MFP_CFG(GPIO103, AF1) +#define GPIO104_MMC2_DAT0 MFP_CFG(GPIO104, AF1) +#define GPIO105_MMC2_CMD MFP_CFG(GPIO105, AF1) +#define GPIO106_MMC2_CLK MFP_CFG(GPIO106, AF1) + +#define DF_IO10_MMC2_DAT3 MFP_CFG(DF_IO10, AF3) +#define DF_IO11_MMC2_DAT2 MFP_CFG(DF_IO11, AF3) +#define DF_IO12_MMC2_DAT1 MFP_CFG(DF_IO12, AF3) +#define DF_IO13_MMC2_DAT0 MFP_CFG(DF_IO13, AF3) +#define DF_IO14_MMC2_CLK MFP_CFG(DF_IO14, AF3) +#define DF_IO15_MMC2_CMD MFP_CFG(DF_IO15, AF3) + +/* BSSP1 */ +#define GPIO12_BSSP1_CLK MFP_CFG(GPIO12, AF3) +#define GPIO13_BSSP1_FRM MFP_CFG(GPIO13, AF3) +#define GPIO14_BSSP1_RXD MFP_CFG(GPIO14, AF3) +#define GPIO15_BSSP1_TXD MFP_CFG(GPIO15, AF3) +#define GPIO97_BSSP1_CLK MFP_CFG(GPIO97, AF5) +#define GPIO98_BSSP1_FRM MFP_CFG(GPIO98, AF5) + +/* BSSP2 */ +#define GPIO84_BSSP2_SDATA_IN MFP_CFG(GPIO84, AF1) +#define GPIO85_BSSP2_BITCLK MFP_CFG(GPIO85, AF1) +#define GPIO86_BSSP2_SYSCLK MFP_CFG(GPIO86, AF1) +#define GPIO87_BSSP2_SYNC MFP_CFG(GPIO87, AF1) +#define GPIO88_BSSP2_DATA_OUT MFP_CFG(GPIO88, AF1) +#define GPIO86_BSSP2_SDATA_IN MFP_CFG(GPIO86, AF4) + +/* BSSP3 */ +#define GPIO79_BSSP3_CLK MFP_CFG(GPIO79, AF1) +#define GPIO80_BSSP3_FRM MFP_CFG(GPIO80, AF1) +#define GPIO81_BSSP3_TXD MFP_CFG(GPIO81, AF1) +#define GPIO82_BSSP3_RXD MFP_CFG(GPIO82, AF1) +#define GPIO83_BSSP3_SYSCLK MFP_CFG(GPIO83, AF1) + +/* BSSP4 */ +#define GPIO43_BSSP4_CLK MFP_CFG(GPIO43, AF4) +#define GPIO44_BSSP4_FRM MFP_CFG(GPIO44, AF4) +#define GPIO45_BSSP4_TXD MFP_CFG(GPIO45, AF4) +#define GPIO46_BSSP4_RXD MFP_CFG(GPIO46, AF4) + +#define GPIO51_BSSP4_CLK MFP_CFG(GPIO51, AF4) +#define GPIO52_BSSP4_FRM MFP_CFG(GPIO52, AF4) +#define GPIO53_BSSP4_TXD MFP_CFG(GPIO53, AF4) +#define GPIO54_BSSP4_RXD MFP_CFG(GPIO54, AF4) + +/* GSSP1 */ +#define GPIO79_GSSP1_CLK MFP_CFG(GPIO79, AF2) +#define GPIO80_GSSP1_FRM MFP_CFG(GPIO80, AF2) +#define GPIO81_GSSP1_TXD MFP_CFG(GPIO81, AF2) +#define GPIO82_GSSP1_RXD MFP_CFG(GPIO82, AF2) +#define GPIO83_GSSP1_SYSCLK MFP_CFG(GPIO83, AF2) + +#define GPIO93_GSSP1_CLK MFP_CFG(GPIO93, AF4) +#define GPIO94_GSSP1_FRM MFP_CFG(GPIO94, AF4) +#define GPIO95_GSSP1_TXD MFP_CFG(GPIO95, AF4) +#define GPIO96_GSSP1_RXD MFP_CFG(GPIO96, AF4) + +/* GSSP2 */ +#define GPIO47_GSSP2_CLK MFP_CFG(GPIO47, AF4) +#define GPIO48_GSSP2_FRM MFP_CFG(GPIO48, AF4) +#define GPIO49_GSSP2_RXD MFP_CFG(GPIO49, AF4) +#define GPIO50_GSSP2_TXD MFP_CFG(GPIO50, AF4) + +#define GPIO69_GSSP2_CLK MFP_CFG(GPIO69, AF4) +#define GPIO70_GSSP2_FRM MFP_CFG(GPIO70, AF4) +#define GPIO71_GSSP2_RXD MFP_CFG(GPIO71, AF4) +#define GPIO72_GSSP2_TXD MFP_CFG(GPIO72, AF4) + +#define GPIO84_GSSP2_RXD MFP_CFG(GPIO84, AF2) +#define GPIO85_GSSP2_CLK MFP_CFG(GPIO85, AF2) +#define GPIO86_GSSP2_SYSCLK MFP_CFG(GPIO86, AF2) +#define GPIO87_GSSP2_FRM MFP_CFG(GPIO87, AF2) +#define GPIO88_GSSP2_TXD MFP_CFG(GPIO88, AF2) +#define GPIO86_GSSP2_RXD MFP_CFG(GPIO86, AF5) + +#define GPIO103_GSSP2_CLK MFP_CFG(GPIO103, AF2) +#define GPIO104_GSSP2_FRM MFP_CFG(GPIO104, AF2) +#define GPIO105_GSSP2_RXD MFP_CFG(GPIO105, AF2) +#define GPIO106_GSSP2_TXD MFP_CFG(GPIO106, AF2) + +/* UART1 - FFUART */ +#define GPIO47_UART1_DSR_N MFP_CFG(GPIO47, AF1) +#define GPIO48_UART1_DTR_N MFP_CFG(GPIO48, AF1) +#define GPIO49_UART1_RI MFP_CFG(GPIO49, AF1) +#define GPIO50_UART1_DCD MFP_CFG(GPIO50, AF1) +#define GPIO51_UART1_CTS MFP_CFG(GPIO51, AF1) +#define GPIO52_UART1_RTS MFP_CFG(GPIO52, AF1) +#define GPIO53_UART1_RXD MFP_CFG(GPIO53, AF1) +#define GPIO54_UART1_TXD MFP_CFG(GPIO54, AF1) + +#define GPIO63_UART1_TXD MFP_CFG(GPIO63, AF2) +#define GPIO64_UART1_RXD MFP_CFG(GPIO64, AF2) +#define GPIO65_UART1_DSR MFP_CFG(GPIO65, AF2) +#define GPIO66_UART1_DTR MFP_CFG(GPIO66, AF2) +#define GPIO67_UART1_RI MFP_CFG(GPIO67, AF2) +#define GPIO68_UART1_DCD MFP_CFG(GPIO68, AF2) +#define GPIO69_UART1_CTS MFP_CFG(GPIO69, AF2) +#define GPIO70_UART1_RTS MFP_CFG(GPIO70, AF2) + +/* UART2 - BTUART */ +#define GPIO91_UART2_RXD MFP_CFG(GPIO91, AF1) +#define GPIO92_UART2_TXD MFP_CFG(GPIO92, AF1) +#define GPIO93_UART2_CTS MFP_CFG(GPIO93, AF1) +#define GPIO94_UART2_RTS MFP_CFG(GPIO94, AF1) + +/* UART3 - STUART */ +#define GPIO43_UART3_RTS MFP_CFG(GPIO43, AF3) +#define GPIO44_UART3_CTS MFP_CFG(GPIO44, AF3) +#define GPIO45_UART3_RXD MFP_CFG(GPIO45, AF3) +#define GPIO46_UART3_TXD MFP_CFG(GPIO46, AF3) + +#define GPIO75_UART3_RTS MFP_CFG(GPIO75, AF5) +#define GPIO76_UART3_CTS MFP_CFG(GPIO76, AF5) +#define GPIO77_UART3_TXD MFP_CFG(GPIO77, AF5) +#define GPIO78_UART3_RXD MFP_CFG(GPIO78, AF5) + +/* DFI */ +#define DF_IO0_DF_IO0 MFP_CFG(DF_IO0, AF2) +#define DF_IO1_DF_IO1 MFP_CFG(DF_IO1, AF2) +#define DF_IO2_DF_IO2 MFP_CFG(DF_IO2, AF2) +#define DF_IO3_DF_IO3 MFP_CFG(DF_IO3, AF2) +#define DF_IO4_DF_IO4 MFP_CFG(DF_IO4, AF2) +#define DF_IO5_DF_IO5 MFP_CFG(DF_IO5, AF2) +#define DF_IO6_DF_IO6 MFP_CFG(DF_IO6, AF2) +#define DF_IO7_DF_IO7 MFP_CFG(DF_IO7, AF2) +#define DF_IO8_DF_IO8 MFP_CFG(DF_IO8, AF2) +#define DF_IO9_DF_IO9 MFP_CFG(DF_IO9, AF2) +#define DF_IO10_DF_IO10 MFP_CFG(DF_IO10, AF2) +#define DF_IO11_DF_IO11 MFP_CFG(DF_IO11, AF2) +#define DF_IO12_DF_IO12 MFP_CFG(DF_IO12, AF2) +#define DF_IO13_DF_IO13 MFP_CFG(DF_IO13, AF2) +#define DF_IO14_DF_IO14 MFP_CFG(DF_IO14, AF2) +#define DF_IO15_DF_IO15 MFP_CFG(DF_IO15, AF2) +#define DF_nADV1_ALE_DF_nADV1 MFP_CFG(DF_nADV1_ALE, AF2) +#define DF_nADV2_ALE_DF_nADV2 MFP_CFG(DF_nADV2_ALE, AF2) +#define DF_nCS0_DF_nCS0 MFP_CFG(DF_nCS0, AF2) +#define DF_nCS1_DF_nCS1 MFP_CFG(DF_nCS1, AF2) +#define DF_nRE_nOE_DF_nOE MFP_CFG(DF_nRE_nOE, AF2) +#define DF_nWE_DF_nWE MFP_CFG(DF_nWE, AF2) + +/* DFI - NAND */ +#define DF_CLE_nOE_ND_CLE MFP_CFG_LPM(DF_CLE_nOE, AF1, PULL_HIGH) +#define DF_INT_RnB_ND_INT_RnB MFP_CFG_LPM(DF_INT_RnB, AF1, PULL_LOW) +#define DF_IO0_ND_IO0 MFP_CFG_LPM(DF_IO0, AF1, PULL_LOW) +#define DF_IO1_ND_IO1 MFP_CFG_LPM(DF_IO1, AF1, PULL_LOW) +#define DF_IO2_ND_IO2 MFP_CFG_LPM(DF_IO2, AF1, PULL_LOW) +#define DF_IO3_ND_IO3 MFP_CFG_LPM(DF_IO3, AF1, PULL_LOW) +#define DF_IO4_ND_IO4 MFP_CFG_LPM(DF_IO4, AF1, PULL_LOW) +#define DF_IO5_ND_IO5 MFP_CFG_LPM(DF_IO5, AF1, PULL_LOW) +#define DF_IO6_ND_IO6 MFP_CFG_LPM(DF_IO6, AF1, PULL_LOW) +#define DF_IO7_ND_IO7 MFP_CFG_LPM(DF_IO7, AF1, PULL_LOW) +#define DF_IO8_ND_IO8 MFP_CFG_LPM(DF_IO8, AF1, PULL_LOW) +#define DF_IO9_ND_IO9 MFP_CFG_LPM(DF_IO9, AF1, PULL_LOW) +#define DF_IO10_ND_IO10 MFP_CFG_LPM(DF_IO10, AF1, PULL_LOW) +#define DF_IO11_ND_IO11 MFP_CFG_LPM(DF_IO11, AF1, PULL_LOW) +#define DF_IO12_ND_IO12 MFP_CFG_LPM(DF_IO12, AF1, PULL_LOW) +#define DF_IO13_ND_IO13 MFP_CFG_LPM(DF_IO13, AF1, PULL_LOW) +#define DF_IO14_ND_IO14 MFP_CFG_LPM(DF_IO14, AF1, PULL_LOW) +#define DF_IO15_ND_IO15 MFP_CFG_LPM(DF_IO15, AF1, PULL_LOW) +#define DF_nADV1_ALE_ND_ALE MFP_CFG_LPM(DF_nADV1_ALE, AF1, PULL_HIGH) +#define DF_nADV2_ALE_ND_ALE MFP_CFG_LPM(DF_nADV2_ALE, AF1, PULL_HIGH) +#define DF_nADV2_ALE_nCS3 MFP_CFG_LPM(DF_nADV2_ALE, AF3, PULL_HIGH) +#define DF_nCS0_ND_nCS0 MFP_CFG_LPM(DF_nCS0, AF1, PULL_HIGH) +#define DF_nCS1_ND_nCS1 MFP_CFG_LPM(DF_nCS1, AF1, PULL_HIGH) +#define DF_nRE_nOE_ND_nRE MFP_CFG_LPM(DF_nRE_nOE, AF1, PULL_HIGH) +#define DF_nWE_ND_nWE MFP_CFG_LPM(DF_nWE, AF1, PULL_HIGH) + +/* PWM */ +#define GPIO41_PWM0 MFP_CFG_LPM(GPIO41, AF1, PULL_LOW) +#define GPIO42_PWM1 MFP_CFG_LPM(GPIO42, AF1, PULL_LOW) +#define GPIO43_PWM3 MFP_CFG_LPM(GPIO43, AF1, PULL_LOW) +#define GPIO20_PWM0 MFP_CFG_LPM(GPIO20, AF2, PULL_LOW) +#define GPIO21_PWM2 MFP_CFG_LPM(GPIO21, AF3, PULL_LOW) +#define GPIO22_PWM3 MFP_CFG_LPM(GPIO22, AF3, PULL_LOW) + +/* CIR */ +#define GPIO46_CIR_OUT MFP_CFG(GPIO46, AF1) +#define GPIO77_CIR_OUT MFP_CFG(GPIO77, AF3) + +/* USB P2 */ +#define GPIO0_USB_P2_7 MFP_CFG(GPIO0, AF3) +#define GPIO15_USB_P2_7 MFP_CFG(GPIO15, AF5) +#define GPIO16_USB_P2_7 MFP_CFG(GPIO16, AF2) +#define GPIO48_USB_P2_7 MFP_CFG(GPIO48, AF7) +#define GPIO49_USB_P2_7 MFP_CFG(GPIO49, AF6) +#define DF_IO9_USB_P2_7 MFP_CFG(DF_IO9, AF3) + +#define GPIO48_USB_P2_8 MFP_CFG(GPIO48, AF2) +#define GPIO50_USB_P2_7 MFP_CFG_X(GPIO50, AF2, DS02X, FLOAT) +#define GPIO51_USB_P2_5 MFP_CFG(GPIO51, AF2) +#define GPIO47_USB_P2_4 MFP_CFG(GPIO47, AF2) +#define GPIO53_USB_P2_3 MFP_CFG(GPIO53, AF2) +#define GPIO54_USB_P2_6 MFP_CFG(GPIO54, AF2) +#define GPIO49_USB_P2_2 MFP_CFG(GPIO49, AF2) +#define GPIO52_USB_P2_1 MFP_CFG(GPIO52, AF2) + +#define GPIO63_USB_P2_8 MFP_CFG(GPIO63, AF3) +#define GPIO64_USB_P2_7 MFP_CFG(GPIO64, AF3) +#define GPIO65_USB_P2_6 MFP_CFG(GPIO65, AF3) +#define GPIO66_USG_P2_5 MFP_CFG(GPIO66, AF3) +#define GPIO67_USB_P2_4 MFP_CFG(GPIO67, AF3) +#define GPIO68_USB_P2_3 MFP_CFG(GPIO68, AF3) +#define GPIO69_USB_P2_2 MFP_CFG(GPIO69, AF3) +#define GPIO70_USB_P2_1 MFP_CFG(GPIO70, AF3) + +/* ULPI */ +#define GPIO31_USB_ULPI_D0 MFP_CFG(GPIO31, AF4) +#define GPIO30_USB_ULPI_D1 MFP_CFG(GPIO30, AF7) +#define GPIO33_USB_ULPI_D2 MFP_CFG(GPIO33, AF5) +#define GPIO34_USB_ULPI_D3 MFP_CFG(GPIO34, AF5) +#define GPIO35_USB_ULPI_D4 MFP_CFG(GPIO35, AF5) +#define GPIO36_USB_ULPI_D5 MFP_CFG(GPIO36, AF5) +#define GPIO41_USB_ULPI_D6 MFP_CFG(GPIO41, AF5) +#define GPIO42_USB_ULPI_D7 MFP_CFG(GPIO42, AF5) +#define GPIO37_USB_ULPI_DIR MFP_CFG(GPIO37, AF4) +#define GPIO38_USB_ULPI_CLK MFP_CFG(GPIO38, AF4) +#define GPIO39_USB_ULPI_STP MFP_CFG(GPIO39, AF4) +#define GPIO40_USB_ULPI_NXT MFP_CFG(GPIO40, AF4) + +#define GPIO3_CLK26MOUTDMD MFP_CFG(GPIO3, AF3) +#define GPIO40_CLK26MOUTDMD MFP_CFG(GPIO40, AF7) +#define GPIO94_CLK26MOUTDMD MFP_CFG(GPIO94, AF5) +#define GPIO104_CLK26MOUTDMD MFP_CFG(GPIO104, AF4) +#define DF_ADDR1_CLK26MOUTDMD MFP_CFG(DF_ADDR2, AF3) +#define DF_ADDR3_CLK26MOUTDMD MFP_CFG(DF_ADDR3, AF3) + +#define GPIO14_CLK26MOUT MFP_CFG(GPIO14, AF5) +#define GPIO38_CLK26MOUT MFP_CFG(GPIO38, AF7) +#define GPIO92_CLK26MOUT MFP_CFG(GPIO92, AF5) +#define GPIO105_CLK26MOUT MFP_CFG(GPIO105, AF4) + +#define GPIO2_CLK13MOUTDMD MFP_CFG(GPIO2, AF3) +#define GPIO39_CLK13MOUTDMD MFP_CFG(GPIO39, AF7) +#define GPIO50_CLK13MOUTDMD MFP_CFG(GPIO50, AF3) +#define GPIO93_CLK13MOUTDMD MFP_CFG(GPIO93, AF5) +#define GPIO103_CLK13MOUTDMD MFP_CFG(GPIO103, AF4) +#define DF_ADDR2_CLK13MOUTDMD MFP_CFG(DF_ADDR2, AF3) + +/* 1 wire */ +#define GPIO95_OW_DQ_IN MFP_CFG(GPIO95, AF5) + +#endif /* __ASM_ARCH_MFP_PXA9xx_H */ diff --git a/arch/arm/mach-pxa/include/mach/mfp.h b/arch/arm/mach-pxa/include/mach/mfp.h new file mode 100644 index 00000000000..482185053a9 --- /dev/null +++ b/arch/arm/mach-pxa/include/mach/mfp.h @@ -0,0 +1,320 @@ +/* + * arch/arm/mach-pxa/include/mach/mfp.h + * + * Multi-Function Pin Definitions + * + * Copyright (C) 2007 Marvell International Ltd. + * + * 2007-8-21: eric miao <eric.miao@marvell.com> + * initial version + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ + +#ifndef __ASM_ARCH_MFP_H +#define __ASM_ARCH_MFP_H + +#define mfp_to_gpio(m) ((m) % 128) + +/* list of all the configurable MFP pins */ +enum { + MFP_PIN_INVALID = -1, + + MFP_PIN_GPIO0 = 0, + MFP_PIN_GPIO1, + MFP_PIN_GPIO2, + MFP_PIN_GPIO3, + MFP_PIN_GPIO4, + MFP_PIN_GPIO5, + MFP_PIN_GPIO6, + MFP_PIN_GPIO7, + MFP_PIN_GPIO8, + MFP_PIN_GPIO9, + MFP_PIN_GPIO10, + MFP_PIN_GPIO11, + MFP_PIN_GPIO12, + MFP_PIN_GPIO13, + MFP_PIN_GPIO14, + MFP_PIN_GPIO15, + MFP_PIN_GPIO16, + MFP_PIN_GPIO17, + MFP_PIN_GPIO18, + MFP_PIN_GPIO19, + MFP_PIN_GPIO20, + MFP_PIN_GPIO21, + MFP_PIN_GPIO22, + MFP_PIN_GPIO23, + MFP_PIN_GPIO24, + MFP_PIN_GPIO25, + MFP_PIN_GPIO26, + MFP_PIN_GPIO27, + MFP_PIN_GPIO28, + MFP_PIN_GPIO29, + MFP_PIN_GPIO30, + MFP_PIN_GPIO31, + MFP_PIN_GPIO32, + MFP_PIN_GPIO33, + MFP_PIN_GPIO34, + MFP_PIN_GPIO35, + MFP_PIN_GPIO36, + MFP_PIN_GPIO37, + MFP_PIN_GPIO38, + MFP_PIN_GPIO39, + MFP_PIN_GPIO40, + MFP_PIN_GPIO41, + MFP_PIN_GPIO42, + MFP_PIN_GPIO43, + MFP_PIN_GPIO44, + MFP_PIN_GPIO45, + MFP_PIN_GPIO46, + MFP_PIN_GPIO47, + MFP_PIN_GPIO48, + MFP_PIN_GPIO49, + MFP_PIN_GPIO50, + MFP_PIN_GPIO51, + MFP_PIN_GPIO52, + MFP_PIN_GPIO53, + MFP_PIN_GPIO54, + MFP_PIN_GPIO55, + MFP_PIN_GPIO56, + MFP_PIN_GPIO57, + MFP_PIN_GPIO58, + MFP_PIN_GPIO59, + MFP_PIN_GPIO60, + MFP_PIN_GPIO61, + MFP_PIN_GPIO62, + MFP_PIN_GPIO63, + MFP_PIN_GPIO64, + MFP_PIN_GPIO65, + MFP_PIN_GPIO66, + MFP_PIN_GPIO67, + MFP_PIN_GPIO68, + MFP_PIN_GPIO69, + MFP_PIN_GPIO70, + MFP_PIN_GPIO71, + MFP_PIN_GPIO72, + MFP_PIN_GPIO73, + MFP_PIN_GPIO74, + MFP_PIN_GPIO75, + MFP_PIN_GPIO76, + MFP_PIN_GPIO77, + MFP_PIN_GPIO78, + MFP_PIN_GPIO79, + MFP_PIN_GPIO80, + MFP_PIN_GPIO81, + MFP_PIN_GPIO82, + MFP_PIN_GPIO83, + MFP_PIN_GPIO84, + MFP_PIN_GPIO85, + MFP_PIN_GPIO86, + MFP_PIN_GPIO87, + MFP_PIN_GPIO88, + MFP_PIN_GPIO89, + MFP_PIN_GPIO90, + MFP_PIN_GPIO91, + MFP_PIN_GPIO92, + MFP_PIN_GPIO93, + MFP_PIN_GPIO94, + MFP_PIN_GPIO95, + MFP_PIN_GPIO96, + MFP_PIN_GPIO97, + MFP_PIN_GPIO98, + MFP_PIN_GPIO99, + MFP_PIN_GPIO100, + MFP_PIN_GPIO101, + MFP_PIN_GPIO102, + MFP_PIN_GPIO103, + MFP_PIN_GPIO104, + MFP_PIN_GPIO105, + MFP_PIN_GPIO106, + MFP_PIN_GPIO107, + MFP_PIN_GPIO108, + MFP_PIN_GPIO109, + MFP_PIN_GPIO110, + MFP_PIN_GPIO111, + MFP_PIN_GPIO112, + MFP_PIN_GPIO113, + MFP_PIN_GPIO114, + MFP_PIN_GPIO115, + MFP_PIN_GPIO116, + MFP_PIN_GPIO117, + MFP_PIN_GPIO118, + MFP_PIN_GPIO119, + MFP_PIN_GPIO120, + MFP_PIN_GPIO121, + MFP_PIN_GPIO122, + MFP_PIN_GPIO123, + MFP_PIN_GPIO124, + MFP_PIN_GPIO125, + MFP_PIN_GPIO126, + MFP_PIN_GPIO127, + MFP_PIN_GPIO0_2, + MFP_PIN_GPIO1_2, + MFP_PIN_GPIO2_2, + MFP_PIN_GPIO3_2, + MFP_PIN_GPIO4_2, + MFP_PIN_GPIO5_2, + MFP_PIN_GPIO6_2, + MFP_PIN_GPIO7_2, + MFP_PIN_GPIO8_2, + MFP_PIN_GPIO9_2, + MFP_PIN_GPIO10_2, + MFP_PIN_GPIO11_2, + MFP_PIN_GPIO12_2, + MFP_PIN_GPIO13_2, + MFP_PIN_GPIO14_2, + MFP_PIN_GPIO15_2, + MFP_PIN_GPIO16_2, + MFP_PIN_GPIO17_2, + + MFP_PIN_ULPI_STP, + MFP_PIN_ULPI_NXT, + MFP_PIN_ULPI_DIR, + + MFP_PIN_nXCVREN, + MFP_PIN_DF_CLE_nOE, + MFP_PIN_DF_nADV1_ALE, + MFP_PIN_DF_SCLK_E, + MFP_PIN_DF_SCLK_S, + MFP_PIN_nBE0, + MFP_PIN_nBE1, + MFP_PIN_DF_nADV2_ALE, + MFP_PIN_DF_INT_RnB, + MFP_PIN_DF_nCS0, + MFP_PIN_DF_nCS1, + MFP_PIN_nLUA, + MFP_PIN_nLLA, + MFP_PIN_DF_nWE, + MFP_PIN_DF_ALE_nWE, + MFP_PIN_DF_nRE_nOE, + MFP_PIN_DF_ADDR0, + MFP_PIN_DF_ADDR1, + MFP_PIN_DF_ADDR2, + MFP_PIN_DF_ADDR3, + MFP_PIN_DF_IO0, + MFP_PIN_DF_IO1, + MFP_PIN_DF_IO2, + MFP_PIN_DF_IO3, + MFP_PIN_DF_IO4, + MFP_PIN_DF_IO5, + MFP_PIN_DF_IO6, + MFP_PIN_DF_IO7, + MFP_PIN_DF_IO8, + MFP_PIN_DF_IO9, + MFP_PIN_DF_IO10, + MFP_PIN_DF_IO11, + MFP_PIN_DF_IO12, + MFP_PIN_DF_IO13, + MFP_PIN_DF_IO14, + MFP_PIN_DF_IO15, + + /* additional pins on PXA930 */ + MFP_PIN_GSIM_UIO, + MFP_PIN_GSIM_UCLK, + MFP_PIN_GSIM_UDET, + MFP_PIN_GSIM_nURST, + MFP_PIN_PMIC_INT, + MFP_PIN_RDY, + + MFP_PIN_MAX, +}; + +/* + * a possible MFP configuration is represented by a 32-bit integer + * + * bit 0.. 9 - MFP Pin Number (1024 Pins Maximum) + * bit 10..12 - Alternate Function Selection + * bit 13..15 - Drive Strength + * bit 16..18 - Low Power Mode State + * bit 19..20 - Low Power Mode Edge Detection + * bit 21..22 - Run Mode Pull State + * + * to facilitate the definition, the following macros are provided + * + * MFP_CFG_DEFAULT - default MFP configuration value, with + * alternate function = 0, + * drive strength = fast 3mA (MFP_DS03X) + * low power mode = default + * edge detection = none + * + * MFP_CFG - default MFPR value with alternate function + * MFP_CFG_DRV - default MFPR value with alternate function and + * pin drive strength + * MFP_CFG_LPM - default MFPR value with alternate function and + * low power mode + * MFP_CFG_X - default MFPR value with alternate function, + * pin drive strength and low power mode + */ + +typedef unsigned long mfp_cfg_t; + +#define MFP_PIN(x) ((x) & 0x3ff) + +#define MFP_AF0 (0x0 << 10) +#define MFP_AF1 (0x1 << 10) +#define MFP_AF2 (0x2 << 10) +#define MFP_AF3 (0x3 << 10) +#define MFP_AF4 (0x4 << 10) +#define MFP_AF5 (0x5 << 10) +#define MFP_AF6 (0x6 << 10) +#define MFP_AF7 (0x7 << 10) +#define MFP_AF_MASK (0x7 << 10) +#define MFP_AF(x) (((x) >> 10) & 0x7) + +#define MFP_DS01X (0x0 << 13) +#define MFP_DS02X (0x1 << 13) +#define MFP_DS03X (0x2 << 13) +#define MFP_DS04X (0x3 << 13) +#define MFP_DS06X (0x4 << 13) +#define MFP_DS08X (0x5 << 13) +#define MFP_DS10X (0x6 << 13) +#define MFP_DS13X (0x7 << 13) +#define MFP_DS_MASK (0x7 << 13) +#define MFP_DS(x) (((x) >> 13) & 0x7) + +#define MFP_LPM_DEFAULT (0x0 << 16) +#define MFP_LPM_DRIVE_LOW (0x1 << 16) +#define MFP_LPM_DRIVE_HIGH (0x2 << 16) +#define MFP_LPM_PULL_LOW (0x3 << 16) +#define MFP_LPM_PULL_HIGH (0x4 << 16) +#define MFP_LPM_FLOAT (0x5 << 16) +#define MFP_LPM_INPUT (0x6 << 16) +#define MFP_LPM_STATE_MASK (0x7 << 16) +#define MFP_LPM_STATE(x) (((x) >> 16) & 0x7) + +#define MFP_LPM_EDGE_NONE (0x0 << 19) +#define MFP_LPM_EDGE_RISE (0x1 << 19) +#define MFP_LPM_EDGE_FALL (0x2 << 19) +#define MFP_LPM_EDGE_BOTH (0x3 << 19) +#define MFP_LPM_EDGE_MASK (0x3 << 19) +#define MFP_LPM_EDGE(x) (((x) >> 19) & 0x3) + +#define MFP_PULL_NONE (0x0 << 21) +#define MFP_PULL_LOW (0x1 << 21) +#define MFP_PULL_HIGH (0x2 << 21) +#define MFP_PULL_BOTH (0x3 << 21) +#define MFP_PULL_MASK (0x3 << 21) +#define MFP_PULL(x) (((x) >> 21) & 0x3) + +#define MFP_CFG_DEFAULT (MFP_AF0 | MFP_DS03X | MFP_LPM_DEFAULT |\ + MFP_LPM_EDGE_NONE | MFP_PULL_NONE) + +#define MFP_CFG(pin, af) \ + ((MFP_CFG_DEFAULT & ~MFP_AF_MASK) |\ + (MFP_PIN(MFP_PIN_##pin) | MFP_##af)) + +#define MFP_CFG_DRV(pin, af, drv) \ + ((MFP_CFG_DEFAULT & ~(MFP_AF_MASK | MFP_DS_MASK)) |\ + (MFP_PIN(MFP_PIN_##pin) | MFP_##af | MFP_##drv)) + +#define MFP_CFG_LPM(pin, af, lpm) \ + ((MFP_CFG_DEFAULT & ~(MFP_AF_MASK | MFP_LPM_STATE_MASK)) |\ + (MFP_PIN(MFP_PIN_##pin) | MFP_##af | MFP_LPM_##lpm)) + +#define MFP_CFG_X(pin, af, drv, lpm) \ + ((MFP_CFG_DEFAULT & ~(MFP_AF_MASK | MFP_DS_MASK | MFP_LPM_STATE_MASK)) |\ + (MFP_PIN(MFP_PIN_##pin) | MFP_##af | MFP_##drv | MFP_LPM_##lpm)) + +#endif /* __ASM_ARCH_MFP_H */ diff --git a/arch/arm/mach-pxa/include/mach/mioa701.h b/arch/arm/mach-pxa/include/mach/mioa701.h new file mode 100644 index 00000000000..8483cb51183 --- /dev/null +++ b/arch/arm/mach-pxa/include/mach/mioa701.h @@ -0,0 +1,67 @@ +#ifndef _MIOA701_H_ +#define _MIOA701_H_ + +#define MIO_CFG_IN(pin, af) \ + ((MFP_CFG_DEFAULT & ~(MFP_AF_MASK | MFP_DIR_MASK)) |\ + (MFP_PIN(pin) | MFP_##af | MFP_DIR_IN)) + +#define MIO_CFG_OUT(pin, af, state) \ + ((MFP_CFG_DEFAULT & ~(MFP_AF_MASK | MFP_DIR_MASK | MFP_LPM_STATE_MASK)) |\ + (MFP_PIN(pin) | MFP_##af | MFP_DIR_OUT | MFP_LPM_##state)) + +/* Global GPIOs */ +#define GPIO9_CHARGE_nEN 9 +#define GPIO18_POWEROFF 18 +#define GPIO87_LCD_POWER 87 + +/* USB */ +#define GPIO13_USB_DETECT 13 +#define GPIO22_USB_ENABLE 22 + +/* SDIO bits */ +#define GPIO78_SDIO_RO 78 +#define GPIO15_SDIO_INSERT 15 +#define GPIO91_SDIO_EN 91 + +/* Bluetooth */ +#define GPIO83_BT_ON 83 + +/* GPS */ +#define GPIO23_GPS_UNKNOWN1 23 +#define GPIO26_GPS_ON 26 +#define GPIO27_GPS_RESET 27 +#define GPIO106_GPS_UNKNOWN2 106 +#define GPIO107_GPS_UNKNOWN3 107 + +/* GSM */ +#define GPIO24_GSM_MOD_RESET_CMD 24 +#define GPIO88_GSM_nMOD_ON_CMD 88 +#define GPIO90_GSM_nMOD_OFF_CMD 90 +#define GPIO114_GSM_nMOD_DTE_UART_STATE 114 +#define GPIO25_GSM_MOD_ON_STATE 25 +#define GPIO113_GSM_EVENT 113 + +/* SOUND */ +#define GPIO12_HPJACK_INSERT 12 + +/* LEDS */ +#define GPIO10_LED_nCharging 10 +#define GPIO97_LED_nBlue 97 +#define GPIO98_LED_nOrange 98 +#define GPIO82_LED_nVibra 82 +#define GPIO115_LED_nKeyboard 115 + +/* Keyboard */ +#define GPIO0_KEY_POWER 0 +#define GPIO93_KEY_VOLUME_UP 93 +#define GPIO94_KEY_VOLUME_DOWN 94 + +extern struct input_dev *mioa701_evdev; +extern void mioa701_gpio_lpm_set(unsigned long mfp_pin); + +/* Assembler externals mioa701_bootresume.S */ +extern u32 mioa701_bootstrap; +extern u32 mioa701_jumpaddr; +extern u32 mioa701_bootstrap_lg; + +#endif /* _MIOA701_H */ diff --git a/arch/arm/mach-pxa/include/mach/mmc.h b/arch/arm/mach-pxa/include/mach/mmc.h new file mode 100644 index 00000000000..6d1304c9270 --- /dev/null +++ b/arch/arm/mach-pxa/include/mach/mmc.h @@ -0,0 +1,23 @@ +#ifndef ASMARM_ARCH_MMC_H +#define ASMARM_ARCH_MMC_H + +#include <linux/mmc/host.h> +#include <linux/interrupt.h> + +struct device; +struct mmc_host; + +struct pxamci_platform_data { + unsigned int ocr_mask; /* available voltages */ + unsigned long detect_delay; /* delay in jiffies before detecting cards after interrupt */ + int (*init)(struct device *, irq_handler_t , void *); + int (*get_ro)(struct device *); + void (*setpower)(struct device *, unsigned int); + void (*exit)(struct device *, void *); +}; + +extern void pxa_set_mci_info(struct pxamci_platform_data *info); +extern void pxa3xx_set_mci2_info(struct pxamci_platform_data *info); +extern void pxa3xx_set_mci3_info(struct pxamci_platform_data *info); + +#endif diff --git a/arch/arm/mach-pxa/include/mach/mtd-xip.h b/arch/arm/mach-pxa/include/mach/mtd-xip.h new file mode 100644 index 00000000000..4d452fcb150 --- /dev/null +++ b/arch/arm/mach-pxa/include/mach/mtd-xip.h @@ -0,0 +1,35 @@ +/* + * MTD primitives for XIP support. Architecture specific functions + * + * Do not include this file directly. It's included from linux/mtd/xip.h + * + * Author: Nicolas Pitre + * Created: Nov 2, 2004 + * Copyright: (C) 2004 MontaVista Software, Inc. + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ + +#ifndef __ARCH_PXA_MTD_XIP_H__ +#define __ARCH_PXA_MTD_XIP_H__ + +#include <mach/pxa-regs.h> + +#define xip_irqpending() (ICIP & ICMR) + +/* we sample OSCR and convert desired delta to usec (1/4 ~= 1000000/3686400) */ +#define xip_currtime() (OSCR) +#define xip_elapsed_since(x) (signed)((OSCR - (x)) / 4) + +/* + * xip_cpu_idle() is used when waiting for a delay equal or larger than + * the system timer tick period. This should put the CPU into idle mode + * to save power and to be woken up only when some interrupts are pending. + * As above, this should not rely upon standard kernel code. + */ + +#define xip_cpu_idle() asm volatile ("mcr p14, 0, %0, c7, c0, 0" :: "r" (1)) + +#endif /* __ARCH_PXA_MTD_XIP_H__ */ diff --git a/arch/arm/mach-pxa/include/mach/ohci.h b/arch/arm/mach-pxa/include/mach/ohci.h new file mode 100644 index 00000000000..95b6e2a6e51 --- /dev/null +++ b/arch/arm/mach-pxa/include/mach/ohci.h @@ -0,0 +1,36 @@ +#ifndef ASMARM_ARCH_OHCI_H +#define ASMARM_ARCH_OHCI_H + +struct device; + +struct pxaohci_platform_data { + int (*init)(struct device *); + void (*exit)(struct device *); + + unsigned long flags; +#define ENABLE_PORT1 (1 << 0) +#define ENABLE_PORT2 (1 << 1) +#define ENABLE_PORT3 (1 << 2) +#define ENABLE_PORT_ALL (ENABLE_PORT1 | ENABLE_PORT2 | ENABLE_PORT3) + +#define POWER_SENSE_LOW (1 << 3) +#define POWER_CONTROL_LOW (1 << 4) +#define NO_OC_PROTECTION (1 << 5) +#define OC_MODE_GLOBAL (0 << 6) +#define OC_MODE_PERPORT (1 << 6) + + int power_on_delay; /* Power On to Power Good time - in ms + * HCD must wait for this duration before + * accessing a powered on port + */ + int port_mode; +#define PMM_NPS_MODE 1 +#define PMM_GLOBAL_MODE 2 +#define PMM_PERPORT_MODE 3 + + int power_budget; +}; + +extern void pxa_set_ohci_info(struct pxaohci_platform_data *info); + +#endif diff --git a/arch/arm/mach-pxa/include/mach/palmtx.h b/arch/arm/mach-pxa/include/mach/palmtx.h new file mode 100644 index 00000000000..1e8bccbda51 --- /dev/null +++ b/arch/arm/mach-pxa/include/mach/palmtx.h @@ -0,0 +1,106 @@ +/* + * GPIOs and interrupts for Palm T|X Handheld Computer + * + * Based on palmld-gpio.h by Alex Osborne + * + * Authors: Marek Vasut <marek.vasut@gmail.com> + * Cristiano P. <cristianop@users.sourceforge.net> + * Jan Herman <2hp@seznam.cz> + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + * + */ + +#ifndef _INCLUDE_PALMTX_H_ +#define _INCLUDE_PALMTX_H_ + +/** HERE ARE GPIOs **/ + +/* GPIOs */ +#define GPIO_NR_PALMTX_GPIO_RESET 1 + +#define GPIO_NR_PALMTX_POWER_DETECT 12 /* 90 */ +#define GPIO_NR_PALMTX_HOTSYNC_BUTTON_N 10 +#define GPIO_NR_PALMTX_EARPHONE_DETECT 107 + +/* SD/MMC */ +#define GPIO_NR_PALMTX_SD_DETECT_N 14 +#define GPIO_NR_PALMTX_SD_POWER 114 /* probably */ +#define GPIO_NR_PALMTX_SD_READONLY 115 /* probably */ + +/* TOUCHSCREEN */ +#define GPIO_NR_PALMTX_WM9712_IRQ 27 + +/* IRDA - disable GPIO connected to SD pin of tranceiver (TFBS4710?) ? */ +#define GPIO_NR_PALMTX_IR_DISABLE 40 + +/* USB */ +#define GPIO_NR_PALMTX_USB_DETECT_N 13 +#define GPIO_NR_PALMTX_USB_POWER 95 +#define GPIO_NR_PALMTX_USB_PULLUP 93 + +/* LCD/BACKLIGHT */ +#define GPIO_NR_PALMTX_BL_POWER 84 +#define GPIO_NR_PALMTX_LCD_POWER 96 + +/* LCD BORDER */ +#define GPIO_NR_PALMTX_BORDER_SWITCH 98 +#define GPIO_NR_PALMTX_BORDER_SELECT 22 + +/* BLUETOOTH */ +#define GPIO_NR_PALMTX_BT_POWER 17 +#define GPIO_NR_PALMTX_BT_RESET 83 + +/* PCMCIA (WiFi) */ +#define GPIO_NR_PALMTX_PCMCIA_POWER1 94 +#define GPIO_NR_PALMTX_PCMCIA_POWER2 108 +#define GPIO_NR_PALMTX_PCMCIA_RESET 79 +#define GPIO_NR_PALMTX_PCMCIA_READY 116 + +/* NAND Flash ... this GPIO may be incorrect! */ +#define GPIO_NR_PALMTX_NAND_BUFFER_DIR 79 + +/* INTERRUPTS */ +#define IRQ_GPIO_PALMTX_SD_DETECT_N IRQ_GPIO(GPIO_NR_PALMTX_SD_DETECT_N) +#define IRQ_GPIO_PALMTX_WM9712_IRQ IRQ_GPIO(GPIO_NR_PALMTX_WM9712_IRQ) +#define IRQ_GPIO_PALMTX_USB_DETECT IRQ_GPIO(GPIO_NR_PALMTX_USB_DETECT) +#define IRQ_GPIO_PALMTX_GPIO_RESET IRQ_GPIO(GPIO_NR_PALMTX_GPIO_RESET) + +/** HERE ARE INIT VALUES **/ + +/* Various addresses */ +#define PALMTX_PCMCIA_PHYS 0x28000000 +#define PALMTX_PCMCIA_VIRT 0xf0000000 +#define PALMTX_PCMCIA_SIZE 0x100000 + +#define PALMTX_PHYS_RAM_START 0xa0000000 +#define PALMTX_PHYS_IO_START 0x40000000 + +#define PALMTX_PHYS_FLASH_START PXA_CS0_PHYS /* ChipSelect 0 */ +#define PALMTX_PHYS_NAND_START PXA_CS1_PHYS /* ChipSelect 1 */ + +/* TOUCHSCREEN */ +#define AC97_LINK_FRAME 21 + + +/* BATTERY */ +#define PALMTX_BAT_MAX_VOLTAGE 4000 /* 4.00v current voltage */ +#define PALMTX_BAT_MIN_VOLTAGE 3550 /* 3.55v critical voltage */ +#define PALMTX_BAT_MAX_CURRENT 0 /* unknokn */ +#define PALMTX_BAT_MIN_CURRENT 0 /* unknown */ +#define PALMTX_BAT_MAX_CHARGE 1 /* unknown */ +#define PALMTX_BAT_MIN_CHARGE 1 /* unknown */ +#define PALMTX_MAX_LIFE_MINS 360 /* on-life in minutes */ + +#define PALMTX_BAT_MEASURE_DELAY (HZ * 1) + +/* BACKLIGHT */ +#define PALMTX_MAX_INTENSITY 0xFE +#define PALMTX_DEFAULT_INTENSITY 0x7E +#define PALMTX_LIMIT_MASK 0x7F +#define PALMTX_PRESCALER 0x3F +#define PALMTX_PERIOD_NS 3500 + +#endif diff --git a/arch/arm/mach-pxa/include/mach/palmz72.h b/arch/arm/mach-pxa/include/mach/palmz72.h new file mode 100644 index 00000000000..5032307ebf7 --- /dev/null +++ b/arch/arm/mach-pxa/include/mach/palmz72.h @@ -0,0 +1,80 @@ +/* + * GPIOs and interrupts for Palm Zire72 Handheld Computer + * + * Authors: Alex Osborne <bobofdoom@gmail.com> + * Jan Herman <2hp@seznam.cz> + * Sergey Lapin <slapin@ossfans.org> + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + * + */ + +#ifndef _INCLUDE_PALMZ72_H_ +#define _INCLUDE_PALMZ72_H_ + +/* Power and control */ +#define GPIO_NR_PALMZ72_GPIO_RESET 1 +#define GPIO_NR_PALMZ72_POWER_DETECT 0 + +/* SD/MMC */ +#define GPIO_NR_PALMZ72_SD_DETECT_N 14 +#define GPIO_NR_PALMZ72_SD_POWER_N 98 +#define GPIO_NR_PALMZ72_SD_RO 115 + +/* Touchscreen */ +#define GPIO_NR_PALMZ72_WM9712_IRQ 27 + +/* IRDA - disable GPIO connected to SD pin of tranceiver (TFBS4710?) ? */ +#define GPIO_NR_PALMZ72_IR_DISABLE 49 + +/* USB */ +#define GPIO_NR_PALMZ72_USB_DETECT_N 15 +#define GPIO_NR_PALMZ72_USB_POWER 95 +#define GPIO_NR_PALMZ72_USB_PULLUP 12 + +/* LCD/Backlight */ +#define GPIO_NR_PALMZ72_BL_POWER 20 +#define GPIO_NR_PALMZ72_LCD_POWER 96 + +/* LED */ +#define GPIO_NR_PALMZ72_LED_GREEN 88 + +/* Bluetooth */ +#define GPIO_NR_PALMZ72_BT_POWER 17 +#define GPIO_NR_PALMZ72_BT_RESET 83 + +/** Initial values **/ + +/* Battery */ +#define PALMZ72_BAT_MAX_VOLTAGE 4000 /* 4.00v current voltage */ +#define PALMZ72_BAT_MIN_VOLTAGE 3550 /* 3.55v critical voltage */ +#define PALMZ72_BAT_MAX_CURRENT 0 /* unknokn */ +#define PALMZ72_BAT_MIN_CURRENT 0 /* unknown */ +#define PALMZ72_BAT_MAX_CHARGE 1 /* unknown */ +#define PALMZ72_BAT_MIN_CHARGE 1 /* unknown */ +#define PALMZ72_MAX_LIFE_MINS 360 /* on-life in minutes */ + +/* Backlight */ +#define PALMZ72_MAX_INTENSITY 0xFE +#define PALMZ72_DEFAULT_INTENSITY 0x7E +#define PALMZ72_LIMIT_MASK 0x7F +#define PALMZ72_PRESCALER 0x3F +#define PALMZ72_PERIOD_NS 3500 + +#ifdef CONFIG_PM +struct palmz72_resume_info { + u32 magic0; /* 0x0 */ + u32 magic1; /* 0x4 */ + u32 resume_addr; /* 0x8 */ + u32 pad[11]; /* 0xc..0x37 */ + u32 arm_control; /* 0x38 */ + u32 aux_control; /* 0x3c */ + u32 ttb; /* 0x40 */ + u32 domain_access; /* 0x44 */ + u32 process_id; /* 0x48 */ +}; +#endif +#endif + diff --git a/arch/arm/mach-pxa/include/mach/pcm027.h b/arch/arm/mach-pxa/include/mach/pcm027.h new file mode 100644 index 00000000000..4dcd2e8baa6 --- /dev/null +++ b/arch/arm/mach-pxa/include/mach/pcm027.h @@ -0,0 +1,75 @@ +/* + * arch/arm/mach-pxa/include/mach/pcm027.h + * + * (c) 2003 Phytec Messtechnik GmbH <armlinux@phytec.de> + * (c) 2007 Juergen Beisert <j.beisert@pengutronix.de> + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA + */ + +/* + * Definitions of CPU card resources only + */ + +/* I2C RTC */ +#define PCM027_RTC_IRQ_GPIO 0 +#define PCM027_RTC_IRQ IRQ_GPIO(PCM027_RTC_IRQ_GPIO) +#define PCM027_RTC_IRQ_EDGE IRQ_TYPE_EDGE_FALLING +#define ADR_PCM027_RTC 0x51 /* I2C address */ + +/* I2C EEPROM */ +#define ADR_PCM027_EEPROM 0x54 /* I2C address */ + +/* Ethernet chip (SMSC91C111) */ +#define PCM027_ETH_IRQ_GPIO 52 +#define PCM027_ETH_IRQ IRQ_GPIO(PCM027_ETH_IRQ_GPIO) +#define PCM027_ETH_IRQ_EDGE IRQ_TYPE_EDGE_RISING +#define PCM027_ETH_PHYS PXA_CS5_PHYS +#define PCM027_ETH_SIZE (1*1024*1024) + +/* CAN controller SJA1000 (unsupported yet) */ +#define PCM027_CAN_IRQ_GPIO 114 +#define PCM027_CAN_IRQ IRQ_GPIO(PCM027_CAN_IRQ_GPIO) +#define PCM027_CAN_IRQ_EDGE IRQ_TYPE_EDGE_FALLING +#define PCM027_CAN_PHYS 0x22000000 +#define PCM027_CAN_SIZE 0x100 + +/* SPI GPIO expander (unsupported yet) */ +#define PCM027_EGPIO_IRQ_GPIO 27 +#define PCM027_EGPIO_IRQ IRQ_GPIO(PCM027_EGPIO_IRQ_GPIO) +#define PCM027_EGPIO_IRQ_EDGE IRQ_TYPE_EDGE_FALLING +#define PCM027_EGPIO_CS 24 +/* + * TODO: Switch this pin from dedicated usage to GPIO if + * more than the MAX7301 device is connected to this SPI bus + */ +#define PCM027_EGPIO_CS_MODE GPIO24_SFRM_MD + +/* Flash memory */ +#define PCM027_FLASH_PHYS 0x00000000 +#define PCM027_FLASH_SIZE 0x02000000 + +/* onboard LEDs connected to GPIO */ +#define PCM027_LED_CPU 90 +#define PCM027_LED_HEARD_BEAT 91 + +/* + * This CPU module needs a baseboard to work. After basic initializing + * its own devices, it calls baseboard's init function. + * TODO: Add your own basebaord init function and call it from + * inside pcm027_init(). This example here is for the developmen board. + * Refer pcm990-baseboard.c + */ +extern void pcm990_baseboard_init(void); diff --git a/arch/arm/mach-pxa/include/mach/pcm990_baseboard.h b/arch/arm/mach-pxa/include/mach/pcm990_baseboard.h new file mode 100644 index 00000000000..8a4383b776d --- /dev/null +++ b/arch/arm/mach-pxa/include/mach/pcm990_baseboard.h @@ -0,0 +1,275 @@ +/* + * arch/arm/mach-pxa/include/mach/pcm990_baseboard.h + * + * (c) 2003 Phytec Messtechnik GmbH <armlinux@phytec.de> + * (c) 2007 Juergen Beisert <j.beisert@pengutronix.de> + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA + */ + +#include <mach/pcm027.h> + +/* + * definitions relevant only when the PCM-990 + * development base board is in use + */ + +/* CPLD's interrupt controller is connected to PCM-027 GPIO 9 */ +#define PCM990_CTRL_INT_IRQ_GPIO 9 +#define PCM990_CTRL_INT_IRQ IRQ_GPIO(PCM990_CTRL_INT_IRQ_GPIO) +#define PCM990_CTRL_INT_IRQ_EDGE IRQ_TYPE_EDGE_RISING +#define PCM990_CTRL_PHYS PXA_CS1_PHYS /* 16-Bit */ +#define PCM990_CTRL_BASE 0xea000000 +#define PCM990_CTRL_SIZE (1*1024*1024) + +#define PCM990_CTRL_PWR_IRQ_GPIO 14 +#define PCM990_CTRL_PWR_IRQ IRQ_GPIO(PCM990_CTRL_PWR_IRQ_GPIO) +#define PCM990_CTRL_PWR_IRQ_EDGE IRQ_TYPE_EDGE_RISING + +/* visible CPLD (U7) registers */ +#define PCM990_CTRL_REG0 0x0000 /* RESET REGISTER */ +#define PCM990_CTRL_SYSRES 0x0001 /* System RESET REGISTER */ +#define PCM990_CTRL_RESOUT 0x0002 /* RESETOUT Enable REGISTER */ +#define PCM990_CTRL_RESGPIO 0x0004 /* RESETGPIO Enable REGISTER */ + +#define PCM990_CTRL_REG1 0x0002 /* Power REGISTER */ +#define PCM990_CTRL_5VOFF 0x0001 /* Disable 5V Regulators */ +#define PCM990_CTRL_CANPWR 0x0004 /* Enable CANPWR ADUM */ +#define PCM990_CTRL_PM_5V 0x0008 /* Read 5V OK */ + +#define PCM990_CTRL_REG2 0x0004 /* LED REGISTER */ +#define PCM990_CTRL_LEDPWR 0x0001 /* POWER LED enable */ +#define PCM990_CTRL_LEDBAS 0x0002 /* BASIS LED enable */ +#define PCM990_CTRL_LEDUSR 0x0004 /* USER LED enable */ + +#define PCM990_CTRL_REG3 0x0006 /* LCD CTRL REGISTER 3 */ +#define PCM990_CTRL_LCDPWR 0x0001 /* RW LCD Power on */ +#define PCM990_CTRL_LCDON 0x0002 /* RW LCD Latch on */ +#define PCM990_CTRL_LCDPOS1 0x0004 /* RW POS 1 */ +#define PCM990_CTRL_LCDPOS2 0x0008 /* RW POS 2 */ + +#define PCM990_CTRL_REG4 0x0008 /* MMC1 CTRL REGISTER 4 */ +#define PCM990_CTRL_MMC1PWR 0x0001 /* RW MMC1 Power on */ + +#define PCM990_CTRL_REG5 0x000A /* MMC2 CTRL REGISTER 5 */ +#define PCM990_CTRL_MMC2PWR 0x0001 /* RW MMC2 Power on */ +#define PCM990_CTRL_MMC2LED 0x0002 /* RW MMC2 LED */ +#define PCM990_CTRL_MMC2DE 0x0004 /* R MMC2 Card detect */ +#define PCM990_CTRL_MMC2WP 0x0008 /* R MMC2 Card write protect */ + +#define PCM990_CTRL_REG6 0x000C /* Interrupt Clear REGISTER */ +#define PCM990_CTRL_INTC0 0x0001 /* Clear Reg BT Detect */ +#define PCM990_CTRL_INTC1 0x0002 /* Clear Reg FR RI */ +#define PCM990_CTRL_INTC2 0x0004 /* Clear Reg MMC1 Detect */ +#define PCM990_CTRL_INTC3 0x0008 /* Clear Reg PM_5V off */ + +#define PCM990_CTRL_REG7 0x000E /* Interrupt Enable REGISTER */ +#define PCM990_CTRL_ENAINT0 0x0001 /* Enable Int BT Detect */ +#define PCM990_CTRL_ENAINT1 0x0002 /* Enable Int FR RI */ +#define PCM990_CTRL_ENAINT2 0x0004 /* Enable Int MMC1 Detect */ +#define PCM990_CTRL_ENAINT3 0x0008 /* Enable Int PM_5V off */ + +#define PCM990_CTRL_REG8 0x0014 /* Uart REGISTER */ +#define PCM990_CTRL_FFSD 0x0001 /* BT Uart Enable */ +#define PCM990_CTRL_BTSD 0x0002 /* FF Uart Enable */ +#define PCM990_CTRL_FFRI 0x0004 /* FF Uart RI detect */ +#define PCM990_CTRL_BTRX 0x0008 /* BT Uart Rx detect */ + +#define PCM990_CTRL_REG9 0x0010 /* AC97 Flash REGISTER */ +#define PCM990_CTRL_FLWP 0x0001 /* pC Flash Write Protect */ +#define PCM990_CTRL_FLDIS 0x0002 /* pC Flash Disable */ +#define PCM990_CTRL_AC97ENA 0x0004 /* Enable AC97 Expansion */ + +#define PCM990_CTRL_REG10 0x0012 /* GPS-REGISTER */ +#define PCM990_CTRL_GPSPWR 0x0004 /* GPS-Modul Power on */ +#define PCM990_CTRL_GPSENA 0x0008 /* GPS-Modul Enable */ + +#define PCM990_CTRL_REG11 0x0014 /* Accu REGISTER */ +#define PCM990_CTRL_ACENA 0x0001 /* Charge Enable */ +#define PCM990_CTRL_ACSEL 0x0002 /* Charge Akku -> DC Enable */ +#define PCM990_CTRL_ACPRES 0x0004 /* DC Present */ +#define PCM990_CTRL_ACALARM 0x0008 /* Error Akku */ + +#define PCM990_CTRL_P2V(x) ((x) - PCM990_CTRL_PHYS + PCM990_CTRL_BASE) +#define PCM990_CTRL_V2P(x) ((x) - PCM990_CTRL_BASE + PCM990_CTRL_PHYS) + +#ifndef __ASSEMBLY__ +# define __PCM990_CTRL_REG(x) \ + (*((volatile unsigned char *)PCM990_CTRL_P2V(x))) +#else +# define __PCM990_CTRL_REG(x) PCM990_CTRL_P2V(x) +#endif + +#define PCM990_INTMSKENA __PCM990_CTRL_REG(PCM990_CTRL_PHYS + PCM990_CTRL_REG7) +#define PCM990_INTSETCLR __PCM990_CTRL_REG(PCM990_CTRL_PHYS + PCM990_CTRL_REG6) +#define PCM990_CTRL0 __PCM990_CTRL_REG(PCM990_CTRL_PHYS + PCM990_CTRL_REG0) +#define PCM990_CTRL1 __PCM990_CTRL_REG(PCM990_CTRL_PHYS + PCM990_CTRL_REG1) +#define PCM990_CTRL2 __PCM990_CTRL_REG(PCM990_CTRL_PHYS + PCM990_CTRL_REG2) +#define PCM990_CTRL3 __PCM990_CTRL_REG(PCM990_CTRL_PHYS + PCM990_CTRL_REG3) +#define PCM990_CTRL4 __PCM990_CTRL_REG(PCM990_CTRL_PHYS + PCM990_CTRL_REG4) +#define PCM990_CTRL5 __PCM990_CTRL_REG(PCM990_CTRL_PHYS + PCM990_CTRL_REG5) +#define PCM990_CTRL6 __PCM990_CTRL_REG(PCM990_CTRL_PHYS + PCM990_CTRL_REG6) +#define PCM990_CTRL7 __PCM990_CTRL_REG(PCM990_CTRL_PHYS + PCM990_CTRL_REG7) +#define PCM990_CTRL8 __PCM990_CTRL_REG(PCM990_CTRL_PHYS + PCM990_CTRL_REG8) +#define PCM990_CTRL9 __PCM990_CTRL_REG(PCM990_CTRL_PHYS + PCM990_CTRL_REG9) +#define PCM990_CTRL10 __PCM990_CTRL_REG(PCM990_CTRL_PHYS + PCM990_CTRL_REG10) +#define PCM990_CTRL11 __PCM990_CTRL_REG(PCM990_CTRL_PHYS + PCM990_CTRL_REG11) + + +/* + * IDE + */ +#define PCM990_IDE_IRQ_GPIO 13 +#define PCM990_IDE_IRQ IRQ_GPIO(PCM990_IDE_IRQ_GPIO) +#define PCM990_IDE_IRQ_EDGE IRQ_TYPE_EDGE_RISING +#define PCM990_IDE_PLD_PHYS 0x20000000 /* 16 bit wide */ +#define PCM990_IDE_PLD_BASE 0xee000000 +#define PCM990_IDE_PLD_SIZE (1*1024*1024) + +/* visible CPLD (U6) registers */ +#define PCM990_IDE_PLD_REG0 0x1000 /* OFFSET IDE REGISTER 0 */ +#define PCM990_IDE_PM5V 0x0004 /* R System VCC_5V */ +#define PCM990_IDE_STBY 0x0008 /* R System StandBy */ + +#define PCM990_IDE_PLD_REG1 0x1002 /* OFFSET IDE REGISTER 1 */ +#define PCM990_IDE_IDEMODE 0x0001 /* R TrueIDE Mode */ +#define PCM990_IDE_DMAENA 0x0004 /* RW DMA Enable */ +#define PCM990_IDE_DMA1_0 0x0008 /* RW 1=DREQ1 0=DREQ0 */ + +#define PCM990_IDE_PLD_REG2 0x1004 /* OFFSET IDE REGISTER 2 */ +#define PCM990_IDE_RESENA 0x0001 /* RW IDE Reset Bit enable */ +#define PCM990_IDE_RES 0x0002 /* RW IDE Reset Bit */ +#define PCM990_IDE_RDY 0x0008 /* RDY */ + +#define PCM990_IDE_PLD_REG3 0x1006 /* OFFSET IDE REGISTER 3 */ +#define PCM990_IDE_IDEOE 0x0001 /* RW Latch on Databus */ +#define PCM990_IDE_IDEON 0x0002 /* RW Latch on Control Address */ +#define PCM990_IDE_IDEIN 0x0004 /* RW Latch on Interrupt usw. */ + +#define PCM990_IDE_PLD_REG4 0x1008 /* OFFSET IDE REGISTER 4 */ +#define PCM990_IDE_PWRENA 0x0001 /* RW IDE Power enable */ +#define PCM990_IDE_5V 0x0002 /* R IDE Power 5V */ +#define PCM990_IDE_PWG 0x0008 /* R IDE Power is on */ + +#define PCM990_IDE_PLD_P2V(x) ((x) - PCM990_IDE_PLD_PHYS + PCM990_IDE_PLD_BASE) +#define PCM990_IDE_PLD_V2P(x) ((x) - PCM990_IDE_PLD_BASE + PCM990_IDE_PLD_PHYS) + +#ifndef __ASSEMBLY__ +# define __PCM990_IDE_PLD_REG(x) \ + (*((volatile unsigned char *)PCM990_IDE_PLD_P2V(x))) +#else +# define __PCM990_IDE_PLD_REG(x) PCM990_IDE_PLD_P2V(x) +#endif + +#define PCM990_IDE0 \ + __PCM990_IDE_PLD_REG(PCM990_IDE_PLD_PHYS + PCM990_IDE_PLD_REG0) +#define PCM990_IDE1 \ + __PCM990_IDE_PLD_REG(PCM990_IDE_PLD_PHYS + PCM990_IDE_PLD_REG1) +#define PCM990_IDE2 \ + __PCM990_IDE_PLD_REG(PCM990_IDE_PLD_PHYS + PCM990_IDE_PLD_REG2) +#define PCM990_IDE3 \ + __PCM990_IDE_PLD_REG(PCM990_IDE_PLD_PHYS + PCM990_IDE_PLD_REG3) +#define PCM990_IDE4 \ + __PCM990_IDE_PLD_REG(PCM990_IDE_PLD_PHYS + PCM990_IDE_PLD_REG4) + +/* + * Compact Flash + */ +#define PCM990_CF_IRQ_GPIO 11 +#define PCM990_CF_IRQ IRQ_GPIO(PCM990_CF_IRQ_GPIO) +#define PCM990_CF_IRQ_EDGE IRQ_TYPE_EDGE_RISING + +#define PCM990_CF_CD_GPIO 12 +#define PCM990_CF_CD IRQ_GPIO(PCM990_CF_CD_GPIO) +#define PCM990_CF_CD_EDGE IRQ_TYPE_EDGE_RISING + +#define PCM990_CF_PLD_PHYS 0x30000000 /* 16 bit wide */ +#define PCM990_CF_PLD_BASE 0xef000000 +#define PCM990_CF_PLD_SIZE (1*1024*1024) +#define PCM990_CF_PLD_P2V(x) ((x) - PCM990_CF_PLD_PHYS + PCM990_CF_PLD_BASE) +#define PCM990_CF_PLD_V2P(x) ((x) - PCM990_CF_PLD_BASE + PCM990_CF_PLD_PHYS) + +/* visible CPLD (U6) registers */ +#define PCM990_CF_PLD_REG0 0x1000 /* OFFSET CF REGISTER 0 */ +#define PCM990_CF_REG0_LED 0x0001 /* RW LED on */ +#define PCM990_CF_REG0_BLK 0x0002 /* RW LED flash when access */ +#define PCM990_CF_REG0_PM5V 0x0004 /* R System VCC_5V enable */ +#define PCM990_CF_REG0_STBY 0x0008 /* R System StandBy */ + +#define PCM990_CF_PLD_REG1 0x1002 /* OFFSET CF REGISTER 1 */ +#define PCM990_CF_REG1_IDEMODE 0x0001 /* RW CF card run as TrueIDE */ +#define PCM990_CF_REG1_CF0 0x0002 /* RW CF card at ADDR 0x28000000 */ + +#define PCM990_CF_PLD_REG2 0x1004 /* OFFSET CF REGISTER 2 */ +#define PCM990_CF_REG2_RES 0x0002 /* RW CF RESET BIT */ +#define PCM990_CF_REG2_RDYENA 0x0004 /* RW Enable CF_RDY */ +#define PCM990_CF_REG2_RDY 0x0008 /* R CF_RDY auf PWAIT */ + +#define PCM990_CF_PLD_REG3 0x1006 /* OFFSET CF REGISTER 3 */ +#define PCM990_CF_REG3_CFOE 0x0001 /* RW Latch on Databus */ +#define PCM990_CF_REG3_CFON 0x0002 /* RW Latch on Control Address */ +#define PCM990_CF_REG3_CFIN 0x0004 /* RW Latch on Interrupt usw. */ +#define PCM990_CF_REG3_CFCD 0x0008 /* RW Latch on CD1/2 VS1/2 usw */ + +#define PCM990_CF_PLD_REG4 0x1008 /* OFFSET CF REGISTER 4 */ +#define PCM990_CF_REG4_PWRENA 0x0001 /* RW CF Power on (CD1/2 = "00") */ +#define PCM990_CF_REG4_5_3V 0x0002 /* RW 1 = 5V CF_VCC 0 = 3 V CF_VCC */ +#define PCM990_CF_REG4_3B 0x0004 /* RW 3.0V Backup from VCC (5_3V=0) */ +#define PCM990_CF_REG4_PWG 0x0008 /* R CF-Power is on */ + +#define PCM990_CF_PLD_REG5 0x100A /* OFFSET CF REGISTER 5 */ +#define PCM990_CF_REG5_BVD1 0x0001 /* R CF /BVD1 */ +#define PCM990_CF_REG5_BVD2 0x0002 /* R CF /BVD2 */ +#define PCM990_CF_REG5_VS1 0x0004 /* R CF /VS1 */ +#define PCM990_CF_REG5_VS2 0x0008 /* R CF /VS2 */ + +#define PCM990_CF_PLD_REG6 0x100C /* OFFSET CF REGISTER 6 */ +#define PCM990_CF_REG6_CD1 0x0001 /* R CF Card_Detect1 */ +#define PCM990_CF_REG6_CD2 0x0002 /* R CF Card_Detect2 */ + +#ifndef __ASSEMBLY__ +# define __PCM990_CF_PLD_REG(x) \ + (*((volatile unsigned char *)PCM990_CF_PLD_P2V(x))) +#else +# define __PCM990_CF_PLD_REG(x) PCM990_CF_PLD_P2V(x) +#endif + +#define PCM990_CF0 __PCM990_CF_PLD_REG(PCM990_CF_PLD_PHYS + PCM990_CF_PLD_REG0) +#define PCM990_CF1 __PCM990_CF_PLD_REG(PCM990_CF_PLD_PHYS + PCM990_CF_PLD_REG1) +#define PCM990_CF2 __PCM990_CF_PLD_REG(PCM990_CF_PLD_PHYS + PCM990_CF_PLD_REG2) +#define PCM990_CF3 __PCM990_CF_PLD_REG(PCM990_CF_PLD_PHYS + PCM990_CF_PLD_REG3) +#define PCM990_CF4 __PCM990_CF_PLD_REG(PCM990_CF_PLD_PHYS + PCM990_CF_PLD_REG4) +#define PCM990_CF5 __PCM990_CF_PLD_REG(PCM990_CF_PLD_PHYS + PCM990_CF_PLD_REG5) +#define PCM990_CF6 __PCM990_CF_PLD_REG(PCM990_CF_PLD_PHYS + PCM990_CF_PLD_REG6) + +/* + * Wolfson AC97 Touch + */ +#define PCM990_AC97_IRQ_GPIO 10 +#define PCM990_AC97_IRQ IRQ_GPIO(PCM990_AC97_IRQ_GPIO) +#define PCM990_AC97_IRQ_EDGE IRQ_TYPE_EDGE_RISING + +/* + * MMC phyCORE + */ +#define PCM990_MMC0_IRQ_GPIO 9 +#define PCM990_MMC0_IRQ IRQ_GPIO(PCM990_MMC0_IRQ_GPIO) +#define PCM990_MMC0_IRQ_EDGE IRQ_TYPE_EDGE_FALLING + +/* + * USB phyCore + */ +#define PCM990_USB_OVERCURRENT (88 | GPIO_ALT_FN_1_IN) +#define PCM990_USB_PWR_EN (89 | GPIO_ALT_FN_2_OUT) diff --git a/arch/arm/mach-pxa/include/mach/pm.h b/arch/arm/mach-pxa/include/mach/pm.h new file mode 100644 index 00000000000..83342469aca --- /dev/null +++ b/arch/arm/mach-pxa/include/mach/pm.h @@ -0,0 +1,29 @@ +/* + * Copyright (c) 2005 Richard Purdie + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + * + */ + +#include <linux/suspend.h> + +struct pxa_cpu_pm_fns { + int save_count; + void (*save)(unsigned long *); + void (*restore)(unsigned long *); + int (*valid)(suspend_state_t state); + void (*enter)(suspend_state_t state); + int (*prepare)(void); + void (*finish)(void); +}; + +extern struct pxa_cpu_pm_fns *pxa_cpu_pm_fns; + +/* sleep.S */ +extern void pxa25x_cpu_suspend(unsigned int); +extern void pxa27x_cpu_suspend(unsigned int); +extern void pxa_cpu_resume(void); + +extern int pxa_pm_enter(suspend_state_t state); diff --git a/arch/arm/mach-pxa/include/mach/poodle.h b/arch/arm/mach-pxa/include/mach/poodle.h new file mode 100644 index 00000000000..0b3e6d051c6 --- /dev/null +++ b/arch/arm/mach-pxa/include/mach/poodle.h @@ -0,0 +1,90 @@ +/* + * arch/arm/mach-pxa/include/mach/poodle.h + * + * May be copied or modified under the terms of the GNU General Public + * License. See linux/COPYING for more information. + * + * Based on: + * arch/arm/mach-sa1100/include/mach/collie.h + * + * ChangeLog: + * 04-06-2001 Lineo Japan, Inc. + * 04-16-2001 SHARP Corporation + * Update to 2.6 John Lenz + */ +#ifndef __ASM_ARCH_POODLE_H +#define __ASM_ARCH_POODLE_H 1 + +/* + * GPIOs + */ +/* PXA GPIOs */ +#define POODLE_GPIO_ON_KEY (0) +#define POODLE_GPIO_AC_IN (1) +#define POODLE_GPIO_CO 16 +#define POODLE_GPIO_TP_INT (5) +#define POODLE_GPIO_TP_CS (24) +#define POODLE_GPIO_WAKEUP (11) /* change battery */ +#define POODLE_GPIO_GA_INT (10) +#define POODLE_GPIO_IR_ON (22) +#define POODLE_GPIO_HP_IN (4) +#define POODLE_GPIO_CF_IRQ (17) +#define POODLE_GPIO_CF_CD (14) +#define POODLE_GPIO_CF_STSCHG (14) +#define POODLE_GPIO_SD_PWR (33) +#define POODLE_GPIO_SD_PWR1 (3) +#define POODLE_GPIO_nSD_CLK (6) +#define POODLE_GPIO_nSD_WP (7) +#define POODLE_GPIO_nSD_INT (8) +#define POODLE_GPIO_nSD_DETECT (9) +#define POODLE_GPIO_MAIN_BAT_LOW (13) +#define POODLE_GPIO_BAT_COVER (13) +#define POODLE_GPIO_USB_PULLUP (20) +#define POODLE_GPIO_ADC_TEMP_ON (21) +#define POODLE_GPIO_BYPASS_ON (36) +#define POODLE_GPIO_CHRG_ON (38) +#define POODLE_GPIO_CHRG_FULL (16) +#define POODLE_GPIO_DISCHARGE_ON (42) /* Enable battery discharge */ + +/* PXA GPIOs */ +#define POODLE_IRQ_GPIO_ON_KEY IRQ_GPIO(0) +#define POODLE_IRQ_GPIO_AC_IN IRQ_GPIO(1) +#define POODLE_IRQ_GPIO_HP_IN IRQ_GPIO(4) +#define POODLE_IRQ_GPIO_CO IRQ_GPIO(16) +#define POODLE_IRQ_GPIO_TP_INT IRQ_GPIO(5) +#define POODLE_IRQ_GPIO_WAKEUP IRQ_GPIO(11) +#define POODLE_IRQ_GPIO_GA_INT IRQ_GPIO(10) +#define POODLE_IRQ_GPIO_CF_IRQ IRQ_GPIO(17) +#define POODLE_IRQ_GPIO_CF_CD IRQ_GPIO(14) +#define POODLE_IRQ_GPIO_nSD_INT IRQ_GPIO(8) +#define POODLE_IRQ_GPIO_nSD_DETECT IRQ_GPIO(9) +#define POODLE_IRQ_GPIO_MAIN_BAT_LOW IRQ_GPIO(13) + +/* SCOOP GPIOs */ +#define POODLE_SCOOP_CHARGE_ON SCOOP_GPCR_PA11 +#define POODLE_SCOOP_CP401 SCOOP_GPCR_PA13 +#define POODLE_SCOOP_VPEN SCOOP_GPCR_PA18 +#define POODLE_SCOOP_L_PCLK SCOOP_GPCR_PA20 +#define POODLE_SCOOP_L_LCLK SCOOP_GPCR_PA21 +#define POODLE_SCOOP_HS_OUT SCOOP_GPCR_PA22 + +#define POODLE_SCOOP_IO_DIR ( POODLE_SCOOP_VPEN | POODLE_SCOOP_HS_OUT ) +#define POODLE_SCOOP_IO_OUT ( 0 ) + +#define POODLE_SCOOP_GPIO_BASE (NR_BUILTIN_GPIO) +#define POODLE_GPIO_CHARGE_ON (POODLE_SCOOP_GPIO_BASE + 0) +#define POODLE_GPIO_CP401 (POODLE_SCOOP_GPIO_BASE + 2) +#define POODLE_GPIO_VPEN (POODLE_SCOOP_GPIO_BASE + 7) +#define POODLE_GPIO_L_PCLK (POODLE_SCOOP_GPIO_BASE + 9) +#define POODLE_GPIO_L_LCLK (POODLE_SCOOP_GPIO_BASE + 10) +#define POODLE_GPIO_HS_OUT (POODLE_SCOOP_GPIO_BASE + 11) + +#define POODLE_LOCOMO_GPIO_AMP_ON LOCOMO_GPIO(8) +#define POODLE_LOCOMO_GPIO_MUTE_L LOCOMO_GPIO(10) +#define POODLE_LOCOMO_GPIO_MUTE_R LOCOMO_GPIO(11) +#define POODLE_LOCOMO_GPIO_232VCC_ON LOCOMO_GPIO(12) +#define POODLE_LOCOMO_GPIO_JK_B LOCOMO_GPIO(13) + +extern struct platform_device poodle_locomo_device; + +#endif /* __ASM_ARCH_POODLE_H */ diff --git a/arch/arm/mach-pxa/include/mach/pxa-regs.h b/arch/arm/mach-pxa/include/mach/pxa-regs.h new file mode 100644 index 00000000000..15295d96000 --- /dev/null +++ b/arch/arm/mach-pxa/include/mach/pxa-regs.h @@ -0,0 +1,768 @@ +/* + * arch/arm/mach-pxa/include/mach/pxa-regs.h + * + * Author: Nicolas Pitre + * Created: Jun 15, 2001 + * Copyright: MontaVista Software Inc. + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ + +#ifndef __PXA_REGS_H +#define __PXA_REGS_H + + +/* + * PXA Chip selects + */ + +#define PXA_CS0_PHYS 0x00000000 +#define PXA_CS1_PHYS 0x04000000 +#define PXA_CS2_PHYS 0x08000000 +#define PXA_CS3_PHYS 0x0C000000 +#define PXA_CS4_PHYS 0x10000000 +#define PXA_CS5_PHYS 0x14000000 + + +/* + * Personal Computer Memory Card International Association (PCMCIA) sockets + */ + +#define PCMCIAPrtSp 0x04000000 /* PCMCIA Partition Space [byte] */ +#define PCMCIASp (4*PCMCIAPrtSp) /* PCMCIA Space [byte] */ +#define PCMCIAIOSp PCMCIAPrtSp /* PCMCIA I/O Space [byte] */ +#define PCMCIAAttrSp PCMCIAPrtSp /* PCMCIA Attribute Space [byte] */ +#define PCMCIAMemSp PCMCIAPrtSp /* PCMCIA Memory Space [byte] */ + +#define PCMCIA0Sp PCMCIASp /* PCMCIA 0 Space [byte] */ +#define PCMCIA0IOSp PCMCIAIOSp /* PCMCIA 0 I/O Space [byte] */ +#define PCMCIA0AttrSp PCMCIAAttrSp /* PCMCIA 0 Attribute Space [byte] */ +#define PCMCIA0MemSp PCMCIAMemSp /* PCMCIA 0 Memory Space [byte] */ + +#define PCMCIA1Sp PCMCIASp /* PCMCIA 1 Space [byte] */ +#define PCMCIA1IOSp PCMCIAIOSp /* PCMCIA 1 I/O Space [byte] */ +#define PCMCIA1AttrSp PCMCIAAttrSp /* PCMCIA 1 Attribute Space [byte] */ +#define PCMCIA1MemSp PCMCIAMemSp /* PCMCIA 1 Memory Space [byte] */ + +#define _PCMCIA(Nb) /* PCMCIA [0..1] */ \ + (0x20000000 + (Nb)*PCMCIASp) +#define _PCMCIAIO(Nb) _PCMCIA (Nb) /* PCMCIA I/O [0..1] */ +#define _PCMCIAAttr(Nb) /* PCMCIA Attribute [0..1] */ \ + (_PCMCIA (Nb) + 2*PCMCIAPrtSp) +#define _PCMCIAMem(Nb) /* PCMCIA Memory [0..1] */ \ + (_PCMCIA (Nb) + 3*PCMCIAPrtSp) + +#define _PCMCIA0 _PCMCIA (0) /* PCMCIA 0 */ +#define _PCMCIA0IO _PCMCIAIO (0) /* PCMCIA 0 I/O */ +#define _PCMCIA0Attr _PCMCIAAttr (0) /* PCMCIA 0 Attribute */ +#define _PCMCIA0Mem _PCMCIAMem (0) /* PCMCIA 0 Memory */ + +#define _PCMCIA1 _PCMCIA (1) /* PCMCIA 1 */ +#define _PCMCIA1IO _PCMCIAIO (1) /* PCMCIA 1 I/O */ +#define _PCMCIA1Attr _PCMCIAAttr (1) /* PCMCIA 1 Attribute */ +#define _PCMCIA1Mem _PCMCIAMem (1) /* PCMCIA 1 Memory */ + + + +/* + * DMA Controller + */ +#define DCSR(x) __REG2(0x40000000, (x) << 2) + +#define DCSR_RUN (1 << 31) /* Run Bit (read / write) */ +#define DCSR_NODESC (1 << 30) /* No-Descriptor Fetch (read / write) */ +#define DCSR_STOPIRQEN (1 << 29) /* Stop Interrupt Enable (read / write) */ +#define DCSR_REQPEND (1 << 8) /* Request Pending (read-only) */ +#define DCSR_STOPSTATE (1 << 3) /* Stop State (read-only) */ +#define DCSR_ENDINTR (1 << 2) /* End Interrupt (read / write) */ +#define DCSR_STARTINTR (1 << 1) /* Start Interrupt (read / write) */ +#define DCSR_BUSERR (1 << 0) /* Bus Error Interrupt (read / write) */ + +#if defined(CONFIG_PXA27x) || defined(CONFIG_PXA3xx) +#define DCSR_EORIRQEN (1 << 28) /* End of Receive Interrupt Enable (R/W) */ +#define DCSR_EORJMPEN (1 << 27) /* Jump to next descriptor on EOR */ +#define DCSR_EORSTOPEN (1 << 26) /* STOP on an EOR */ +#define DCSR_SETCMPST (1 << 25) /* Set Descriptor Compare Status */ +#define DCSR_CLRCMPST (1 << 24) /* Clear Descriptor Compare Status */ +#define DCSR_CMPST (1 << 10) /* The Descriptor Compare Status */ +#define DCSR_EORINTR (1 << 9) /* The end of Receive */ +#endif + +#define DALGN __REG(0x400000a0) /* DMA Alignment Register */ +#define DINT __REG(0x400000f0) /* DMA Interrupt Register */ + +#define DRCMR(n) (*(((n) < 64) ? \ + &__REG2(0x40000100, ((n) & 0x3f) << 2) : \ + &__REG2(0x40001100, ((n) & 0x3f) << 2))) + +#define DRCMR_MAPVLD (1 << 7) /* Map Valid (read / write) */ +#define DRCMR_CHLNUM 0x1f /* mask for Channel Number (read / write) */ + +#define DDADR(x) __REG2(0x40000200, (x) << 4) +#define DSADR(x) __REG2(0x40000204, (x) << 4) +#define DTADR(x) __REG2(0x40000208, (x) << 4) +#define DCMD(x) __REG2(0x4000020c, (x) << 4) + +#define DDADR_DESCADDR 0xfffffff0 /* Address of next descriptor (mask) */ +#define DDADR_STOP (1 << 0) /* Stop (read / write) */ + +#define DCMD_INCSRCADDR (1 << 31) /* Source Address Increment Setting. */ +#define DCMD_INCTRGADDR (1 << 30) /* Target Address Increment Setting. */ +#define DCMD_FLOWSRC (1 << 29) /* Flow Control by the source. */ +#define DCMD_FLOWTRG (1 << 28) /* Flow Control by the target. */ +#define DCMD_STARTIRQEN (1 << 22) /* Start Interrupt Enable */ +#define DCMD_ENDIRQEN (1 << 21) /* End Interrupt Enable */ +#define DCMD_ENDIAN (1 << 18) /* Device Endian-ness. */ +#define DCMD_BURST8 (1 << 16) /* 8 byte burst */ +#define DCMD_BURST16 (2 << 16) /* 16 byte burst */ +#define DCMD_BURST32 (3 << 16) /* 32 byte burst */ +#define DCMD_WIDTH1 (1 << 14) /* 1 byte width */ +#define DCMD_WIDTH2 (2 << 14) /* 2 byte width (HalfWord) */ +#define DCMD_WIDTH4 (3 << 14) /* 4 byte width (Word) */ +#define DCMD_LENGTH 0x01fff /* length mask (max = 8K - 1) */ + + +/* + * UARTs + */ + +/* Full Function UART (FFUART) */ +#define FFUART FFRBR +#define FFRBR __REG(0x40100000) /* Receive Buffer Register (read only) */ +#define FFTHR __REG(0x40100000) /* Transmit Holding Register (write only) */ +#define FFIER __REG(0x40100004) /* Interrupt Enable Register (read/write) */ +#define FFIIR __REG(0x40100008) /* Interrupt ID Register (read only) */ +#define FFFCR __REG(0x40100008) /* FIFO Control Register (write only) */ +#define FFLCR __REG(0x4010000C) /* Line Control Register (read/write) */ +#define FFMCR __REG(0x40100010) /* Modem Control Register (read/write) */ +#define FFLSR __REG(0x40100014) /* Line Status Register (read only) */ +#define FFMSR __REG(0x40100018) /* Modem Status Register (read only) */ +#define FFSPR __REG(0x4010001C) /* Scratch Pad Register (read/write) */ +#define FFISR __REG(0x40100020) /* Infrared Selection Register (read/write) */ +#define FFDLL __REG(0x40100000) /* Divisor Latch Low Register (DLAB = 1) (read/write) */ +#define FFDLH __REG(0x40100004) /* Divisor Latch High Register (DLAB = 1) (read/write) */ + +/* Bluetooth UART (BTUART) */ +#define BTUART BTRBR +#define BTRBR __REG(0x40200000) /* Receive Buffer Register (read only) */ +#define BTTHR __REG(0x40200000) /* Transmit Holding Register (write only) */ +#define BTIER __REG(0x40200004) /* Interrupt Enable Register (read/write) */ +#define BTIIR __REG(0x40200008) /* Interrupt ID Register (read only) */ +#define BTFCR __REG(0x40200008) /* FIFO Control Register (write only) */ +#define BTLCR __REG(0x4020000C) /* Line Control Register (read/write) */ +#define BTMCR __REG(0x40200010) /* Modem Control Register (read/write) */ +#define BTLSR __REG(0x40200014) /* Line Status Register (read only) */ +#define BTMSR __REG(0x40200018) /* Modem Status Register (read only) */ +#define BTSPR __REG(0x4020001C) /* Scratch Pad Register (read/write) */ +#define BTISR __REG(0x40200020) /* Infrared Selection Register (read/write) */ +#define BTDLL __REG(0x40200000) /* Divisor Latch Low Register (DLAB = 1) (read/write) */ +#define BTDLH __REG(0x40200004) /* Divisor Latch High Register (DLAB = 1) (read/write) */ + +/* Standard UART (STUART) */ +#define STUART STRBR +#define STRBR __REG(0x40700000) /* Receive Buffer Register (read only) */ +#define STTHR __REG(0x40700000) /* Transmit Holding Register (write only) */ +#define STIER __REG(0x40700004) /* Interrupt Enable Register (read/write) */ +#define STIIR __REG(0x40700008) /* Interrupt ID Register (read only) */ +#define STFCR __REG(0x40700008) /* FIFO Control Register (write only) */ +#define STLCR __REG(0x4070000C) /* Line Control Register (read/write) */ +#define STMCR __REG(0x40700010) /* Modem Control Register (read/write) */ +#define STLSR __REG(0x40700014) /* Line Status Register (read only) */ +#define STMSR __REG(0x40700018) /* Reserved */ +#define STSPR __REG(0x4070001C) /* Scratch Pad Register (read/write) */ +#define STISR __REG(0x40700020) /* Infrared Selection Register (read/write) */ +#define STDLL __REG(0x40700000) /* Divisor Latch Low Register (DLAB = 1) (read/write) */ +#define STDLH __REG(0x40700004) /* Divisor Latch High Register (DLAB = 1) (read/write) */ + +/* Hardware UART (HWUART) */ +#define HWUART HWRBR +#define HWRBR __REG(0x41600000) /* Receive Buffer Register (read only) */ +#define HWTHR __REG(0x41600000) /* Transmit Holding Register (write only) */ +#define HWIER __REG(0x41600004) /* Interrupt Enable Register (read/write) */ +#define HWIIR __REG(0x41600008) /* Interrupt ID Register (read only) */ +#define HWFCR __REG(0x41600008) /* FIFO Control Register (write only) */ +#define HWLCR __REG(0x4160000C) /* Line Control Register (read/write) */ +#define HWMCR __REG(0x41600010) /* Modem Control Register (read/write) */ +#define HWLSR __REG(0x41600014) /* Line Status Register (read only) */ +#define HWMSR __REG(0x41600018) /* Modem Status Register (read only) */ +#define HWSPR __REG(0x4160001C) /* Scratch Pad Register (read/write) */ +#define HWISR __REG(0x41600020) /* Infrared Selection Register (read/write) */ +#define HWFOR __REG(0x41600024) /* Receive FIFO Occupancy Register (read only) */ +#define HWABR __REG(0x41600028) /* Auto-Baud Control Register (read/write) */ +#define HWACR __REG(0x4160002C) /* Auto-Baud Count Register (read only) */ +#define HWDLL __REG(0x41600000) /* Divisor Latch Low Register (DLAB = 1) (read/write) */ +#define HWDLH __REG(0x41600004) /* Divisor Latch High Register (DLAB = 1) (read/write) */ + +#define IER_DMAE (1 << 7) /* DMA Requests Enable */ +#define IER_UUE (1 << 6) /* UART Unit Enable */ +#define IER_NRZE (1 << 5) /* NRZ coding Enable */ +#define IER_RTIOE (1 << 4) /* Receiver Time Out Interrupt Enable */ +#define IER_MIE (1 << 3) /* Modem Interrupt Enable */ +#define IER_RLSE (1 << 2) /* Receiver Line Status Interrupt Enable */ +#define IER_TIE (1 << 1) /* Transmit Data request Interrupt Enable */ +#define IER_RAVIE (1 << 0) /* Receiver Data Available Interrupt Enable */ + +#define IIR_FIFOES1 (1 << 7) /* FIFO Mode Enable Status */ +#define IIR_FIFOES0 (1 << 6) /* FIFO Mode Enable Status */ +#define IIR_TOD (1 << 3) /* Time Out Detected */ +#define IIR_IID2 (1 << 2) /* Interrupt Source Encoded */ +#define IIR_IID1 (1 << 1) /* Interrupt Source Encoded */ +#define IIR_IP (1 << 0) /* Interrupt Pending (active low) */ + +#define FCR_ITL2 (1 << 7) /* Interrupt Trigger Level */ +#define FCR_ITL1 (1 << 6) /* Interrupt Trigger Level */ +#define FCR_RESETTF (1 << 2) /* Reset Transmitter FIFO */ +#define FCR_RESETRF (1 << 1) /* Reset Receiver FIFO */ +#define FCR_TRFIFOE (1 << 0) /* Transmit and Receive FIFO Enable */ +#define FCR_ITL_1 (0) +#define FCR_ITL_8 (FCR_ITL1) +#define FCR_ITL_16 (FCR_ITL2) +#define FCR_ITL_32 (FCR_ITL2|FCR_ITL1) + +#define LCR_DLAB (1 << 7) /* Divisor Latch Access Bit */ +#define LCR_SB (1 << 6) /* Set Break */ +#define LCR_STKYP (1 << 5) /* Sticky Parity */ +#define LCR_EPS (1 << 4) /* Even Parity Select */ +#define LCR_PEN (1 << 3) /* Parity Enable */ +#define LCR_STB (1 << 2) /* Stop Bit */ +#define LCR_WLS1 (1 << 1) /* Word Length Select */ +#define LCR_WLS0 (1 << 0) /* Word Length Select */ + +#define LSR_FIFOE (1 << 7) /* FIFO Error Status */ +#define LSR_TEMT (1 << 6) /* Transmitter Empty */ +#define LSR_TDRQ (1 << 5) /* Transmit Data Request */ +#define LSR_BI (1 << 4) /* Break Interrupt */ +#define LSR_FE (1 << 3) /* Framing Error */ +#define LSR_PE (1 << 2) /* Parity Error */ +#define LSR_OE (1 << 1) /* Overrun Error */ +#define LSR_DR (1 << 0) /* Data Ready */ + +#define MCR_LOOP (1 << 4) +#define MCR_OUT2 (1 << 3) /* force MSR_DCD in loopback mode */ +#define MCR_OUT1 (1 << 2) /* force MSR_RI in loopback mode */ +#define MCR_RTS (1 << 1) /* Request to Send */ +#define MCR_DTR (1 << 0) /* Data Terminal Ready */ + +#define MSR_DCD (1 << 7) /* Data Carrier Detect */ +#define MSR_RI (1 << 6) /* Ring Indicator */ +#define MSR_DSR (1 << 5) /* Data Set Ready */ +#define MSR_CTS (1 << 4) /* Clear To Send */ +#define MSR_DDCD (1 << 3) /* Delta Data Carrier Detect */ +#define MSR_TERI (1 << 2) /* Trailing Edge Ring Indicator */ +#define MSR_DDSR (1 << 1) /* Delta Data Set Ready */ +#define MSR_DCTS (1 << 0) /* Delta Clear To Send */ + +/* + * IrSR (Infrared Selection Register) + */ +#define STISR_RXPL (1 << 4) /* Receive Data Polarity */ +#define STISR_TXPL (1 << 3) /* Transmit Data Polarity */ +#define STISR_XMODE (1 << 2) /* Transmit Pulse Width Select */ +#define STISR_RCVEIR (1 << 1) /* Receiver SIR Enable */ +#define STISR_XMITIR (1 << 0) /* Transmitter SIR Enable */ + + +/* + * I2C registers - moved into drivers/i2c/busses/i2c-pxa.c + */ + +/* + * Serial Audio Controller - moved into sound/soc/pxa/pxa2xx-i2s.c + */ + +/* + * AC97 Controller registers + */ + +#define POCR __REG(0x40500000) /* PCM Out Control Register */ +#define POCR_FEIE (1 << 3) /* FIFO Error Interrupt Enable */ +#define POCR_FSRIE (1 << 1) /* FIFO Service Request Interrupt Enable */ + +#define PICR __REG(0x40500004) /* PCM In Control Register */ +#define PICR_FEIE (1 << 3) /* FIFO Error Interrupt Enable */ +#define PICR_FSRIE (1 << 1) /* FIFO Service Request Interrupt Enable */ + +#define MCCR __REG(0x40500008) /* Mic In Control Register */ +#define MCCR_FEIE (1 << 3) /* FIFO Error Interrupt Enable */ +#define MCCR_FSRIE (1 << 1) /* FIFO Service Request Interrupt Enable */ + +#define GCR __REG(0x4050000C) /* Global Control Register */ +#ifdef CONFIG_PXA3xx +#define GCR_CLKBPB (1 << 31) /* Internal clock enable */ +#endif +#define GCR_nDMAEN (1 << 24) /* non DMA Enable */ +#define GCR_CDONE_IE (1 << 19) /* Command Done Interrupt Enable */ +#define GCR_SDONE_IE (1 << 18) /* Status Done Interrupt Enable */ +#define GCR_SECRDY_IEN (1 << 9) /* Secondary Ready Interrupt Enable */ +#define GCR_PRIRDY_IEN (1 << 8) /* Primary Ready Interrupt Enable */ +#define GCR_SECRES_IEN (1 << 5) /* Secondary Resume Interrupt Enable */ +#define GCR_PRIRES_IEN (1 << 4) /* Primary Resume Interrupt Enable */ +#define GCR_ACLINK_OFF (1 << 3) /* AC-link Shut Off */ +#define GCR_WARM_RST (1 << 2) /* AC97 Warm Reset */ +#define GCR_COLD_RST (1 << 1) /* AC'97 Cold Reset (0 = active) */ +#define GCR_GIE (1 << 0) /* Codec GPI Interrupt Enable */ + +#define POSR __REG(0x40500010) /* PCM Out Status Register */ +#define POSR_FIFOE (1 << 4) /* FIFO error */ +#define POSR_FSR (1 << 2) /* FIFO Service Request */ + +#define PISR __REG(0x40500014) /* PCM In Status Register */ +#define PISR_FIFOE (1 << 4) /* FIFO error */ +#define PISR_EOC (1 << 3) /* DMA End-of-Chain (exclusive clear) */ +#define PISR_FSR (1 << 2) /* FIFO Service Request */ + +#define MCSR __REG(0x40500018) /* Mic In Status Register */ +#define MCSR_FIFOE (1 << 4) /* FIFO error */ +#define MCSR_EOC (1 << 3) /* DMA End-of-Chain (exclusive clear) */ +#define MCSR_FSR (1 << 2) /* FIFO Service Request */ + +#define GSR __REG(0x4050001C) /* Global Status Register */ +#define GSR_CDONE (1 << 19) /* Command Done */ +#define GSR_SDONE (1 << 18) /* Status Done */ +#define GSR_RDCS (1 << 15) /* Read Completion Status */ +#define GSR_BIT3SLT12 (1 << 14) /* Bit 3 of slot 12 */ +#define GSR_BIT2SLT12 (1 << 13) /* Bit 2 of slot 12 */ +#define GSR_BIT1SLT12 (1 << 12) /* Bit 1 of slot 12 */ +#define GSR_SECRES (1 << 11) /* Secondary Resume Interrupt */ +#define GSR_PRIRES (1 << 10) /* Primary Resume Interrupt */ +#define GSR_SCR (1 << 9) /* Secondary Codec Ready */ +#define GSR_PCR (1 << 8) /* Primary Codec Ready */ +#define GSR_MCINT (1 << 7) /* Mic In Interrupt */ +#define GSR_POINT (1 << 6) /* PCM Out Interrupt */ +#define GSR_PIINT (1 << 5) /* PCM In Interrupt */ +#define GSR_ACOFFD (1 << 3) /* AC-link Shut Off Done */ +#define GSR_MOINT (1 << 2) /* Modem Out Interrupt */ +#define GSR_MIINT (1 << 1) /* Modem In Interrupt */ +#define GSR_GSCI (1 << 0) /* Codec GPI Status Change Interrupt */ + +#define CAR __REG(0x40500020) /* CODEC Access Register */ +#define CAR_CAIP (1 << 0) /* Codec Access In Progress */ + +#define PCDR __REG(0x40500040) /* PCM FIFO Data Register */ +#define MCDR __REG(0x40500060) /* Mic-in FIFO Data Register */ + +#define MOCR __REG(0x40500100) /* Modem Out Control Register */ +#define MOCR_FEIE (1 << 3) /* FIFO Error */ +#define MOCR_FSRIE (1 << 1) /* FIFO Service Request Interrupt Enable */ + +#define MICR __REG(0x40500108) /* Modem In Control Register */ +#define MICR_FEIE (1 << 3) /* FIFO Error */ +#define MICR_FSRIE (1 << 1) /* FIFO Service Request Interrupt Enable */ + +#define MOSR __REG(0x40500110) /* Modem Out Status Register */ +#define MOSR_FIFOE (1 << 4) /* FIFO error */ +#define MOSR_FSR (1 << 2) /* FIFO Service Request */ + +#define MISR __REG(0x40500118) /* Modem In Status Register */ +#define MISR_FIFOE (1 << 4) /* FIFO error */ +#define MISR_EOC (1 << 3) /* DMA End-of-Chain (exclusive clear) */ +#define MISR_FSR (1 << 2) /* FIFO Service Request */ + +#define MODR __REG(0x40500140) /* Modem FIFO Data Register */ + +#define PAC_REG_BASE __REG(0x40500200) /* Primary Audio Codec */ +#define SAC_REG_BASE __REG(0x40500300) /* Secondary Audio Codec */ +#define PMC_REG_BASE __REG(0x40500400) /* Primary Modem Codec */ +#define SMC_REG_BASE __REG(0x40500500) /* Secondary Modem Codec */ + + +/* + * Fast Infrared Communication Port + */ + +#define FICP __REG(0x40800000) /* Start of FICP area */ +#define ICCR0 __REG(0x40800000) /* ICP Control Register 0 */ +#define ICCR1 __REG(0x40800004) /* ICP Control Register 1 */ +#define ICCR2 __REG(0x40800008) /* ICP Control Register 2 */ +#define ICDR __REG(0x4080000c) /* ICP Data Register */ +#define ICSR0 __REG(0x40800014) /* ICP Status Register 0 */ +#define ICSR1 __REG(0x40800018) /* ICP Status Register 1 */ + +#define ICCR0_AME (1 << 7) /* Address match enable */ +#define ICCR0_TIE (1 << 6) /* Transmit FIFO interrupt enable */ +#define ICCR0_RIE (1 << 5) /* Recieve FIFO interrupt enable */ +#define ICCR0_RXE (1 << 4) /* Receive enable */ +#define ICCR0_TXE (1 << 3) /* Transmit enable */ +#define ICCR0_TUS (1 << 2) /* Transmit FIFO underrun select */ +#define ICCR0_LBM (1 << 1) /* Loopback mode */ +#define ICCR0_ITR (1 << 0) /* IrDA transmission */ + +#define ICCR2_RXP (1 << 3) /* Receive Pin Polarity select */ +#define ICCR2_TXP (1 << 2) /* Transmit Pin Polarity select */ +#define ICCR2_TRIG (3 << 0) /* Receive FIFO Trigger threshold */ +#define ICCR2_TRIG_8 (0 << 0) /* >= 8 bytes */ +#define ICCR2_TRIG_16 (1 << 0) /* >= 16 bytes */ +#define ICCR2_TRIG_32 (2 << 0) /* >= 32 bytes */ + +#ifdef CONFIG_PXA27x +#define ICSR0_EOC (1 << 6) /* DMA End of Descriptor Chain */ +#endif +#define ICSR0_FRE (1 << 5) /* Framing error */ +#define ICSR0_RFS (1 << 4) /* Receive FIFO service request */ +#define ICSR0_TFS (1 << 3) /* Transnit FIFO service request */ +#define ICSR0_RAB (1 << 2) /* Receiver abort */ +#define ICSR0_TUR (1 << 1) /* Trunsmit FIFO underun */ +#define ICSR0_EIF (1 << 0) /* End/Error in FIFO */ + +#define ICSR1_ROR (1 << 6) /* Receiver FIFO underrun */ +#define ICSR1_CRE (1 << 5) /* CRC error */ +#define ICSR1_EOF (1 << 4) /* End of frame */ +#define ICSR1_TNF (1 << 3) /* Transmit FIFO not full */ +#define ICSR1_RNE (1 << 2) /* Receive FIFO not empty */ +#define ICSR1_TBY (1 << 1) /* Tramsmiter busy flag */ +#define ICSR1_RSY (1 << 0) /* Recevier synchronized flag */ + + +/* + * Real Time Clock + */ + +#define RCNR __REG(0x40900000) /* RTC Count Register */ +#define RTAR __REG(0x40900004) /* RTC Alarm Register */ +#define RTSR __REG(0x40900008) /* RTC Status Register */ +#define RTTR __REG(0x4090000C) /* RTC Timer Trim Register */ +#define PIAR __REG(0x40900038) /* Periodic Interrupt Alarm Register */ + +#define RTSR_PICE (1 << 15) /* Periodic interrupt count enable */ +#define RTSR_PIALE (1 << 14) /* Periodic interrupt Alarm enable */ +#define RTSR_HZE (1 << 3) /* HZ interrupt enable */ +#define RTSR_ALE (1 << 2) /* RTC alarm interrupt enable */ +#define RTSR_HZ (1 << 1) /* HZ rising-edge detected */ +#define RTSR_AL (1 << 0) /* RTC alarm detected */ + + +/* + * OS Timer & Match Registers + */ + +#define OSMR0 __REG(0x40A00000) /* */ +#define OSMR1 __REG(0x40A00004) /* */ +#define OSMR2 __REG(0x40A00008) /* */ +#define OSMR3 __REG(0x40A0000C) /* */ +#define OSMR4 __REG(0x40A00080) /* */ +#define OSCR __REG(0x40A00010) /* OS Timer Counter Register */ +#define OSCR4 __REG(0x40A00040) /* OS Timer Counter Register */ +#define OMCR4 __REG(0x40A000C0) /* */ +#define OSSR __REG(0x40A00014) /* OS Timer Status Register */ +#define OWER __REG(0x40A00018) /* OS Timer Watchdog Enable Register */ +#define OIER __REG(0x40A0001C) /* OS Timer Interrupt Enable Register */ + +#define OSSR_M3 (1 << 3) /* Match status channel 3 */ +#define OSSR_M2 (1 << 2) /* Match status channel 2 */ +#define OSSR_M1 (1 << 1) /* Match status channel 1 */ +#define OSSR_M0 (1 << 0) /* Match status channel 0 */ + +#define OWER_WME (1 << 0) /* Watchdog Match Enable */ + +#define OIER_E3 (1 << 3) /* Interrupt enable channel 3 */ +#define OIER_E2 (1 << 2) /* Interrupt enable channel 2 */ +#define OIER_E1 (1 << 1) /* Interrupt enable channel 1 */ +#define OIER_E0 (1 << 0) /* Interrupt enable channel 0 */ + + +/* + * Pulse Width Modulator + */ + +#define PWM_CTRL0 __REG(0x40B00000) /* PWM 0 Control Register */ +#define PWM_PWDUTY0 __REG(0x40B00004) /* PWM 0 Duty Cycle Register */ +#define PWM_PERVAL0 __REG(0x40B00008) /* PWM 0 Period Control Register */ + +#define PWM_CTRL1 __REG(0x40C00000) /* PWM 1Control Register */ +#define PWM_PWDUTY1 __REG(0x40C00004) /* PWM 1 Duty Cycle Register */ +#define PWM_PERVAL1 __REG(0x40C00008) /* PWM 1 Period Control Register */ + + +/* + * Interrupt Controller + */ + +#define ICIP __REG(0x40D00000) /* Interrupt Controller IRQ Pending Register */ +#define ICMR __REG(0x40D00004) /* Interrupt Controller Mask Register */ +#define ICLR __REG(0x40D00008) /* Interrupt Controller Level Register */ +#define ICFP __REG(0x40D0000C) /* Interrupt Controller FIQ Pending Register */ +#define ICPR __REG(0x40D00010) /* Interrupt Controller Pending Register */ +#define ICCR __REG(0x40D00014) /* Interrupt Controller Control Register */ + +#define ICIP2 __REG(0x40D0009C) /* Interrupt Controller IRQ Pending Register 2 */ +#define ICMR2 __REG(0x40D000A0) /* Interrupt Controller Mask Register 2 */ +#define ICLR2 __REG(0x40D000A4) /* Interrupt Controller Level Register 2 */ +#define ICFP2 __REG(0x40D000A8) /* Interrupt Controller FIQ Pending Register 2 */ +#define ICPR2 __REG(0x40D000AC) /* Interrupt Controller Pending Register 2 */ + +/* + * General Purpose I/O + */ + +#define GPIO0_BASE ((void __iomem *)io_p2v(0x40E00000)) +#define GPIO1_BASE ((void __iomem *)io_p2v(0x40E00004)) +#define GPIO2_BASE ((void __iomem *)io_p2v(0x40E00008)) +#define GPIO3_BASE ((void __iomem *)io_p2v(0x40E00100)) + +#define GPLR_OFFSET 0x00 +#define GPDR_OFFSET 0x0C +#define GPSR_OFFSET 0x18 +#define GPCR_OFFSET 0x24 +#define GRER_OFFSET 0x30 +#define GFER_OFFSET 0x3C +#define GEDR_OFFSET 0x48 + +#define GPLR0 __REG(0x40E00000) /* GPIO Pin-Level Register GPIO<31:0> */ +#define GPLR1 __REG(0x40E00004) /* GPIO Pin-Level Register GPIO<63:32> */ +#define GPLR2 __REG(0x40E00008) /* GPIO Pin-Level Register GPIO<80:64> */ + +#define GPDR0 __REG(0x40E0000C) /* GPIO Pin Direction Register GPIO<31:0> */ +#define GPDR1 __REG(0x40E00010) /* GPIO Pin Direction Register GPIO<63:32> */ +#define GPDR2 __REG(0x40E00014) /* GPIO Pin Direction Register GPIO<80:64> */ + +#define GPSR0 __REG(0x40E00018) /* GPIO Pin Output Set Register GPIO<31:0> */ +#define GPSR1 __REG(0x40E0001C) /* GPIO Pin Output Set Register GPIO<63:32> */ +#define GPSR2 __REG(0x40E00020) /* GPIO Pin Output Set Register GPIO<80:64> */ + +#define GPCR0 __REG(0x40E00024) /* GPIO Pin Output Clear Register GPIO<31:0> */ +#define GPCR1 __REG(0x40E00028) /* GPIO Pin Output Clear Register GPIO <63:32> */ +#define GPCR2 __REG(0x40E0002C) /* GPIO Pin Output Clear Register GPIO <80:64> */ + +#define GRER0 __REG(0x40E00030) /* GPIO Rising-Edge Detect Register GPIO<31:0> */ +#define GRER1 __REG(0x40E00034) /* GPIO Rising-Edge Detect Register GPIO<63:32> */ +#define GRER2 __REG(0x40E00038) /* GPIO Rising-Edge Detect Register GPIO<80:64> */ + +#define GFER0 __REG(0x40E0003C) /* GPIO Falling-Edge Detect Register GPIO<31:0> */ +#define GFER1 __REG(0x40E00040) /* GPIO Falling-Edge Detect Register GPIO<63:32> */ +#define GFER2 __REG(0x40E00044) /* GPIO Falling-Edge Detect Register GPIO<80:64> */ + +#define GEDR0 __REG(0x40E00048) /* GPIO Edge Detect Status Register GPIO<31:0> */ +#define GEDR1 __REG(0x40E0004C) /* GPIO Edge Detect Status Register GPIO<63:32> */ +#define GEDR2 __REG(0x40E00050) /* GPIO Edge Detect Status Register GPIO<80:64> */ + +#define GAFR0_L __REG(0x40E00054) /* GPIO Alternate Function Select Register GPIO<15:0> */ +#define GAFR0_U __REG(0x40E00058) /* GPIO Alternate Function Select Register GPIO<31:16> */ +#define GAFR1_L __REG(0x40E0005C) /* GPIO Alternate Function Select Register GPIO<47:32> */ +#define GAFR1_U __REG(0x40E00060) /* GPIO Alternate Function Select Register GPIO<63:48> */ +#define GAFR2_L __REG(0x40E00064) /* GPIO Alternate Function Select Register GPIO<79:64> */ +#define GAFR2_U __REG(0x40E00068) /* GPIO Alternate Function Select Register GPIO<95-80> */ +#define GAFR3_L __REG(0x40E0006C) /* GPIO Alternate Function Select Register GPIO<111:96> */ +#define GAFR3_U __REG(0x40E00070) /* GPIO Alternate Function Select Register GPIO<127:112> */ + +#define GPLR3 __REG(0x40E00100) /* GPIO Pin-Level Register GPIO<127:96> */ +#define GPDR3 __REG(0x40E0010C) /* GPIO Pin Direction Register GPIO<127:96> */ +#define GPSR3 __REG(0x40E00118) /* GPIO Pin Output Set Register GPIO<127:96> */ +#define GPCR3 __REG(0x40E00124) /* GPIO Pin Output Clear Register GPIO<127:96> */ +#define GRER3 __REG(0x40E00130) /* GPIO Rising-Edge Detect Register GPIO<127:96> */ +#define GFER3 __REG(0x40E0013C) /* GPIO Falling-Edge Detect Register GPIO<127:96> */ +#define GEDR3 __REG(0x40E00148) /* GPIO Edge Detect Status Register GPIO<127:96> */ + +/* More handy macros. The argument is a literal GPIO number. */ + +#define GPIO_bit(x) (1 << ((x) & 0x1f)) + +#if defined(CONFIG_PXA27x) || defined(CONFIG_PXA3xx) + +/* Interrupt Controller */ + +#define _GPLR(x) __REG2(0x40E00000, ((x) & 0x60) >> 3) +#define _GPDR(x) __REG2(0x40E0000C, ((x) & 0x60) >> 3) +#define _GPSR(x) __REG2(0x40E00018, ((x) & 0x60) >> 3) +#define _GPCR(x) __REG2(0x40E00024, ((x) & 0x60) >> 3) +#define _GRER(x) __REG2(0x40E00030, ((x) & 0x60) >> 3) +#define _GFER(x) __REG2(0x40E0003C, ((x) & 0x60) >> 3) +#define _GEDR(x) __REG2(0x40E00048, ((x) & 0x60) >> 3) +#define _GAFR(x) __REG2(0x40E00054, ((x) & 0x70) >> 2) + +#define GPLR(x) (*((((x) & 0x7f) < 96) ? &_GPLR(x) : &GPLR3)) +#define GPDR(x) (*((((x) & 0x7f) < 96) ? &_GPDR(x) : &GPDR3)) +#define GPSR(x) (*((((x) & 0x7f) < 96) ? &_GPSR(x) : &GPSR3)) +#define GPCR(x) (*((((x) & 0x7f) < 96) ? &_GPCR(x) : &GPCR3)) +#define GRER(x) (*((((x) & 0x7f) < 96) ? &_GRER(x) : &GRER3)) +#define GFER(x) (*((((x) & 0x7f) < 96) ? &_GFER(x) : &GFER3)) +#define GEDR(x) (*((((x) & 0x7f) < 96) ? &_GEDR(x) : &GEDR3)) +#define GAFR(x) (*((((x) & 0x7f) < 96) ? &_GAFR(x) : \ + ((((x) & 0x7f) < 112) ? &GAFR3_L : &GAFR3_U))) +#else + +#define GPLR(x) __REG2(0x40E00000, ((x) & 0x60) >> 3) +#define GPDR(x) __REG2(0x40E0000C, ((x) & 0x60) >> 3) +#define GPSR(x) __REG2(0x40E00018, ((x) & 0x60) >> 3) +#define GPCR(x) __REG2(0x40E00024, ((x) & 0x60) >> 3) +#define GRER(x) __REG2(0x40E00030, ((x) & 0x60) >> 3) +#define GFER(x) __REG2(0x40E0003C, ((x) & 0x60) >> 3) +#define GEDR(x) __REG2(0x40E00048, ((x) & 0x60) >> 3) +#define GAFR(x) __REG2(0x40E00054, ((x) & 0x70) >> 2) + +#endif + +/* + * Power Manager - see pxa2xx-regs.h + */ + +/* + * SSP Serial Port Registers - see arch/arm/mach-pxa/include/mach/regs-ssp.h + */ + +/* + * MultiMediaCard (MMC) controller - see drivers/mmc/host/pxamci.h + */ + +/* + * Core Clock - see arch/arm/mach-pxa/include/mach/pxa2xx-regs.h + */ + +#ifdef CONFIG_PXA27x + +/* Camera Interface */ +#define CICR0 __REG(0x50000000) +#define CICR1 __REG(0x50000004) +#define CICR2 __REG(0x50000008) +#define CICR3 __REG(0x5000000C) +#define CICR4 __REG(0x50000010) +#define CISR __REG(0x50000014) +#define CIFR __REG(0x50000018) +#define CITOR __REG(0x5000001C) +#define CIBR0 __REG(0x50000028) +#define CIBR1 __REG(0x50000030) +#define CIBR2 __REG(0x50000038) + +#define CICR0_DMAEN (1 << 31) /* DMA request enable */ +#define CICR0_PAR_EN (1 << 30) /* Parity enable */ +#define CICR0_SL_CAP_EN (1 << 29) /* Capture enable for slave mode */ +#define CICR0_ENB (1 << 28) /* Camera interface enable */ +#define CICR0_DIS (1 << 27) /* Camera interface disable */ +#define CICR0_SIM (0x7 << 24) /* Sensor interface mode mask */ +#define CICR0_TOM (1 << 9) /* Time-out mask */ +#define CICR0_RDAVM (1 << 8) /* Receive-data-available mask */ +#define CICR0_FEM (1 << 7) /* FIFO-empty mask */ +#define CICR0_EOLM (1 << 6) /* End-of-line mask */ +#define CICR0_PERRM (1 << 5) /* Parity-error mask */ +#define CICR0_QDM (1 << 4) /* Quick-disable mask */ +#define CICR0_CDM (1 << 3) /* Disable-done mask */ +#define CICR0_SOFM (1 << 2) /* Start-of-frame mask */ +#define CICR0_EOFM (1 << 1) /* End-of-frame mask */ +#define CICR0_FOM (1 << 0) /* FIFO-overrun mask */ + +#define CICR1_TBIT (1 << 31) /* Transparency bit */ +#define CICR1_RGBT_CONV (0x3 << 29) /* RGBT conversion mask */ +#define CICR1_PPL (0x7ff << 15) /* Pixels per line mask */ +#define CICR1_RGB_CONV (0x7 << 12) /* RGB conversion mask */ +#define CICR1_RGB_F (1 << 11) /* RGB format */ +#define CICR1_YCBCR_F (1 << 10) /* YCbCr format */ +#define CICR1_RGB_BPP (0x7 << 7) /* RGB bis per pixel mask */ +#define CICR1_RAW_BPP (0x3 << 5) /* Raw bis per pixel mask */ +#define CICR1_COLOR_SP (0x3 << 3) /* Color space mask */ +#define CICR1_DW (0x7 << 0) /* Data width mask */ + +#define CICR2_BLW (0xff << 24) /* Beginning-of-line pixel clock + wait count mask */ +#define CICR2_ELW (0xff << 16) /* End-of-line pixel clock + wait count mask */ +#define CICR2_HSW (0x3f << 10) /* Horizontal sync pulse width mask */ +#define CICR2_BFPW (0x3f << 3) /* Beginning-of-frame pixel clock + wait count mask */ +#define CICR2_FSW (0x7 << 0) /* Frame stabilization + wait count mask */ + +#define CICR3_BFW (0xff << 24) /* Beginning-of-frame line clock + wait count mask */ +#define CICR3_EFW (0xff << 16) /* End-of-frame line clock + wait count mask */ +#define CICR3_VSW (0x3f << 10) /* Vertical sync pulse width mask */ +#define CICR3_BFPW (0x3f << 3) /* Beginning-of-frame pixel clock + wait count mask */ +#define CICR3_LPF (0x7ff << 0) /* Lines per frame mask */ + +#define CICR4_MCLK_DLY (0x3 << 24) /* MCLK Data Capture Delay mask */ +#define CICR4_PCLK_EN (1 << 23) /* Pixel clock enable */ +#define CICR4_PCP (1 << 22) /* Pixel clock polarity */ +#define CICR4_HSP (1 << 21) /* Horizontal sync polarity */ +#define CICR4_VSP (1 << 20) /* Vertical sync polarity */ +#define CICR4_MCLK_EN (1 << 19) /* MCLK enable */ +#define CICR4_FR_RATE (0x7 << 8) /* Frame rate mask */ +#define CICR4_DIV (0xff << 0) /* Clock divisor mask */ + +#define CISR_FTO (1 << 15) /* FIFO time-out */ +#define CISR_RDAV_2 (1 << 14) /* Channel 2 receive data available */ +#define CISR_RDAV_1 (1 << 13) /* Channel 1 receive data available */ +#define CISR_RDAV_0 (1 << 12) /* Channel 0 receive data available */ +#define CISR_FEMPTY_2 (1 << 11) /* Channel 2 FIFO empty */ +#define CISR_FEMPTY_1 (1 << 10) /* Channel 1 FIFO empty */ +#define CISR_FEMPTY_0 (1 << 9) /* Channel 0 FIFO empty */ +#define CISR_EOL (1 << 8) /* End of line */ +#define CISR_PAR_ERR (1 << 7) /* Parity error */ +#define CISR_CQD (1 << 6) /* Camera interface quick disable */ +#define CISR_CDD (1 << 5) /* Camera interface disable done */ +#define CISR_SOF (1 << 4) /* Start of frame */ +#define CISR_EOF (1 << 3) /* End of frame */ +#define CISR_IFO_2 (1 << 2) /* FIFO overrun for Channel 2 */ +#define CISR_IFO_1 (1 << 1) /* FIFO overrun for Channel 1 */ +#define CISR_IFO_0 (1 << 0) /* FIFO overrun for Channel 0 */ + +#define CIFR_FLVL2 (0x7f << 23) /* FIFO 2 level mask */ +#define CIFR_FLVL1 (0x7f << 16) /* FIFO 1 level mask */ +#define CIFR_FLVL0 (0xff << 8) /* FIFO 0 level mask */ +#define CIFR_THL_0 (0x3 << 4) /* Threshold Level for Channel 0 FIFO */ +#define CIFR_RESET_F (1 << 3) /* Reset input FIFOs */ +#define CIFR_FEN2 (1 << 2) /* FIFO enable for channel 2 */ +#define CIFR_FEN1 (1 << 1) /* FIFO enable for channel 1 */ +#define CIFR_FEN0 (1 << 0) /* FIFO enable for channel 0 */ + +#define SRAM_SIZE 0x40000 /* 4x64K */ + +#define SRAM_MEM_PHYS 0x5C000000 + +#define IMPMCR __REG(0x58000000) /* IM Power Management Control Reg */ +#define IMPMSR __REG(0x58000008) /* IM Power Management Status Reg */ + +#define IMPMCR_PC3 (0x3 << 22) /* Bank 3 Power Control */ +#define IMPMCR_PC3_RUN_MODE (0x0 << 22) /* Run mode */ +#define IMPMCR_PC3_STANDBY_MODE (0x1 << 22) /* Standby mode */ +#define IMPMCR_PC3_AUTO_MODE (0x3 << 22) /* Automatically controlled */ + +#define IMPMCR_PC2 (0x3 << 20) /* Bank 2 Power Control */ +#define IMPMCR_PC2_RUN_MODE (0x0 << 20) /* Run mode */ +#define IMPMCR_PC2_STANDBY_MODE (0x1 << 20) /* Standby mode */ +#define IMPMCR_PC2_AUTO_MODE (0x3 << 20) /* Automatically controlled */ + +#define IMPMCR_PC1 (0x3 << 18) /* Bank 1 Power Control */ +#define IMPMCR_PC1_RUN_MODE (0x0 << 18) /* Run mode */ +#define IMPMCR_PC1_STANDBY_MODE (0x1 << 18) /* Standby mode */ +#define IMPMCR_PC1_AUTO_MODE (0x3 << 18) /* Automatically controlled */ + +#define IMPMCR_PC0 (0x3 << 16) /* Bank 0 Power Control */ +#define IMPMCR_PC0_RUN_MODE (0x0 << 16) /* Run mode */ +#define IMPMCR_PC0_STANDBY_MODE (0x1 << 16) /* Standby mode */ +#define IMPMCR_PC0_AUTO_MODE (0x3 << 16) /* Automatically controlled */ + +#define IMPMCR_AW3 (1 << 11) /* Bank 3 Automatic Wake-up enable */ +#define IMPMCR_AW2 (1 << 10) /* Bank 2 Automatic Wake-up enable */ +#define IMPMCR_AW1 (1 << 9) /* Bank 1 Automatic Wake-up enable */ +#define IMPMCR_AW0 (1 << 8) /* Bank 0 Automatic Wake-up enable */ + +#define IMPMCR_DST (0xFF << 0) /* Delay Standby Time, ms */ + +#define IMPMSR_PS3 (0x3 << 6) /* Bank 3 Power Status: */ +#define IMPMSR_PS3_RUN_MODE (0x0 << 6) /* Run mode */ +#define IMPMSR_PS3_STANDBY_MODE (0x1 << 6) /* Standby mode */ + +#define IMPMSR_PS2 (0x3 << 4) /* Bank 2 Power Status: */ +#define IMPMSR_PS2_RUN_MODE (0x0 << 4) /* Run mode */ +#define IMPMSR_PS2_STANDBY_MODE (0x1 << 4) /* Standby mode */ + +#define IMPMSR_PS1 (0x3 << 2) /* Bank 1 Power Status: */ +#define IMPMSR_PS1_RUN_MODE (0x0 << 2) /* Run mode */ +#define IMPMSR_PS1_STANDBY_MODE (0x1 << 2) /* Standby mode */ + +#define IMPMSR_PS0 (0x3 << 0) /* Bank 0 Power Status: */ +#define IMPMSR_PS0_RUN_MODE (0x0 << 0) /* Run mode */ +#define IMPMSR_PS0_STANDBY_MODE (0x1 << 0) /* Standby mode */ + +#endif + +/* PWRMODE register M field values */ + +#define PWRMODE_IDLE 0x1 +#define PWRMODE_STANDBY 0x2 +#define PWRMODE_SLEEP 0x3 +#define PWRMODE_DEEPSLEEP 0x7 + +#endif diff --git a/arch/arm/mach-pxa/include/mach/pxa25x-udc.h b/arch/arm/mach-pxa/include/mach/pxa25x-udc.h new file mode 100644 index 00000000000..1b80a4805a6 --- /dev/null +++ b/arch/arm/mach-pxa/include/mach/pxa25x-udc.h @@ -0,0 +1,163 @@ +#ifndef _ASM_ARCH_PXA25X_UDC_H +#define _ASM_ARCH_PXA25X_UDC_H + +#ifdef _ASM_ARCH_PXA27X_UDC_H +#error "You can't include both PXA25x and PXA27x UDC support" +#endif + +#define UDC_RES1 __REG(0x40600004) /* UDC Undocumented - Reserved1 */ +#define UDC_RES2 __REG(0x40600008) /* UDC Undocumented - Reserved2 */ +#define UDC_RES3 __REG(0x4060000C) /* UDC Undocumented - Reserved3 */ + +#define UDCCR __REG(0x40600000) /* UDC Control Register */ +#define UDCCR_UDE (1 << 0) /* UDC enable */ +#define UDCCR_UDA (1 << 1) /* UDC active */ +#define UDCCR_RSM (1 << 2) /* Device resume */ +#define UDCCR_RESIR (1 << 3) /* Resume interrupt request */ +#define UDCCR_SUSIR (1 << 4) /* Suspend interrupt request */ +#define UDCCR_SRM (1 << 5) /* Suspend/resume interrupt mask */ +#define UDCCR_RSTIR (1 << 6) /* Reset interrupt request */ +#define UDCCR_REM (1 << 7) /* Reset interrupt mask */ + +#define UDCCS0 __REG(0x40600010) /* UDC Endpoint 0 Control/Status Register */ +#define UDCCS0_OPR (1 << 0) /* OUT packet ready */ +#define UDCCS0_IPR (1 << 1) /* IN packet ready */ +#define UDCCS0_FTF (1 << 2) /* Flush Tx FIFO */ +#define UDCCS0_DRWF (1 << 3) /* Device remote wakeup feature */ +#define UDCCS0_SST (1 << 4) /* Sent stall */ +#define UDCCS0_FST (1 << 5) /* Force stall */ +#define UDCCS0_RNE (1 << 6) /* Receive FIFO no empty */ +#define UDCCS0_SA (1 << 7) /* Setup active */ + +/* Bulk IN - Endpoint 1,6,11 */ +#define UDCCS1 __REG(0x40600014) /* UDC Endpoint 1 (IN) Control/Status Register */ +#define UDCCS6 __REG(0x40600028) /* UDC Endpoint 6 (IN) Control/Status Register */ +#define UDCCS11 __REG(0x4060003C) /* UDC Endpoint 11 (IN) Control/Status Register */ + +#define UDCCS_BI_TFS (1 << 0) /* Transmit FIFO service */ +#define UDCCS_BI_TPC (1 << 1) /* Transmit packet complete */ +#define UDCCS_BI_FTF (1 << 2) /* Flush Tx FIFO */ +#define UDCCS_BI_TUR (1 << 3) /* Transmit FIFO underrun */ +#define UDCCS_BI_SST (1 << 4) /* Sent stall */ +#define UDCCS_BI_FST (1 << 5) /* Force stall */ +#define UDCCS_BI_TSP (1 << 7) /* Transmit short packet */ + +/* Bulk OUT - Endpoint 2,7,12 */ +#define UDCCS2 __REG(0x40600018) /* UDC Endpoint 2 (OUT) Control/Status Register */ +#define UDCCS7 __REG(0x4060002C) /* UDC Endpoint 7 (OUT) Control/Status Register */ +#define UDCCS12 __REG(0x40600040) /* UDC Endpoint 12 (OUT) Control/Status Register */ + +#define UDCCS_BO_RFS (1 << 0) /* Receive FIFO service */ +#define UDCCS_BO_RPC (1 << 1) /* Receive packet complete */ +#define UDCCS_BO_DME (1 << 3) /* DMA enable */ +#define UDCCS_BO_SST (1 << 4) /* Sent stall */ +#define UDCCS_BO_FST (1 << 5) /* Force stall */ +#define UDCCS_BO_RNE (1 << 6) /* Receive FIFO not empty */ +#define UDCCS_BO_RSP (1 << 7) /* Receive short packet */ + +/* Isochronous IN - Endpoint 3,8,13 */ +#define UDCCS3 __REG(0x4060001C) /* UDC Endpoint 3 (IN) Control/Status Register */ +#define UDCCS8 __REG(0x40600030) /* UDC Endpoint 8 (IN) Control/Status Register */ +#define UDCCS13 __REG(0x40600044) /* UDC Endpoint 13 (IN) Control/Status Register */ + +#define UDCCS_II_TFS (1 << 0) /* Transmit FIFO service */ +#define UDCCS_II_TPC (1 << 1) /* Transmit packet complete */ +#define UDCCS_II_FTF (1 << 2) /* Flush Tx FIFO */ +#define UDCCS_II_TUR (1 << 3) /* Transmit FIFO underrun */ +#define UDCCS_II_TSP (1 << 7) /* Transmit short packet */ + +/* Isochronous OUT - Endpoint 4,9,14 */ +#define UDCCS4 __REG(0x40600020) /* UDC Endpoint 4 (OUT) Control/Status Register */ +#define UDCCS9 __REG(0x40600034) /* UDC Endpoint 9 (OUT) Control/Status Register */ +#define UDCCS14 __REG(0x40600048) /* UDC Endpoint 14 (OUT) Control/Status Register */ + +#define UDCCS_IO_RFS (1 << 0) /* Receive FIFO service */ +#define UDCCS_IO_RPC (1 << 1) /* Receive packet complete */ +#define UDCCS_IO_ROF (1 << 2) /* Receive overflow */ +#define UDCCS_IO_DME (1 << 3) /* DMA enable */ +#define UDCCS_IO_RNE (1 << 6) /* Receive FIFO not empty */ +#define UDCCS_IO_RSP (1 << 7) /* Receive short packet */ + +/* Interrupt IN - Endpoint 5,10,15 */ +#define UDCCS5 __REG(0x40600024) /* UDC Endpoint 5 (Interrupt) Control/Status Register */ +#define UDCCS10 __REG(0x40600038) /* UDC Endpoint 10 (Interrupt) Control/Status Register */ +#define UDCCS15 __REG(0x4060004C) /* UDC Endpoint 15 (Interrupt) Control/Status Register */ + +#define UDCCS_INT_TFS (1 << 0) /* Transmit FIFO service */ +#define UDCCS_INT_TPC (1 << 1) /* Transmit packet complete */ +#define UDCCS_INT_FTF (1 << 2) /* Flush Tx FIFO */ +#define UDCCS_INT_TUR (1 << 3) /* Transmit FIFO underrun */ +#define UDCCS_INT_SST (1 << 4) /* Sent stall */ +#define UDCCS_INT_FST (1 << 5) /* Force stall */ +#define UDCCS_INT_TSP (1 << 7) /* Transmit short packet */ + +#define UFNRH __REG(0x40600060) /* UDC Frame Number Register High */ +#define UFNRL __REG(0x40600064) /* UDC Frame Number Register Low */ +#define UBCR2 __REG(0x40600068) /* UDC Byte Count Reg 2 */ +#define UBCR4 __REG(0x4060006c) /* UDC Byte Count Reg 4 */ +#define UBCR7 __REG(0x40600070) /* UDC Byte Count Reg 7 */ +#define UBCR9 __REG(0x40600074) /* UDC Byte Count Reg 9 */ +#define UBCR12 __REG(0x40600078) /* UDC Byte Count Reg 12 */ +#define UBCR14 __REG(0x4060007c) /* UDC Byte Count Reg 14 */ +#define UDDR0 __REG(0x40600080) /* UDC Endpoint 0 Data Register */ +#define UDDR1 __REG(0x40600100) /* UDC Endpoint 1 Data Register */ +#define UDDR2 __REG(0x40600180) /* UDC Endpoint 2 Data Register */ +#define UDDR3 __REG(0x40600200) /* UDC Endpoint 3 Data Register */ +#define UDDR4 __REG(0x40600400) /* UDC Endpoint 4 Data Register */ +#define UDDR5 __REG(0x406000A0) /* UDC Endpoint 5 Data Register */ +#define UDDR6 __REG(0x40600600) /* UDC Endpoint 6 Data Register */ +#define UDDR7 __REG(0x40600680) /* UDC Endpoint 7 Data Register */ +#define UDDR8 __REG(0x40600700) /* UDC Endpoint 8 Data Register */ +#define UDDR9 __REG(0x40600900) /* UDC Endpoint 9 Data Register */ +#define UDDR10 __REG(0x406000C0) /* UDC Endpoint 10 Data Register */ +#define UDDR11 __REG(0x40600B00) /* UDC Endpoint 11 Data Register */ +#define UDDR12 __REG(0x40600B80) /* UDC Endpoint 12 Data Register */ +#define UDDR13 __REG(0x40600C00) /* UDC Endpoint 13 Data Register */ +#define UDDR14 __REG(0x40600E00) /* UDC Endpoint 14 Data Register */ +#define UDDR15 __REG(0x406000E0) /* UDC Endpoint 15 Data Register */ + +#define UICR0 __REG(0x40600050) /* UDC Interrupt Control Register 0 */ + +#define UICR0_IM0 (1 << 0) /* Interrupt mask ep 0 */ +#define UICR0_IM1 (1 << 1) /* Interrupt mask ep 1 */ +#define UICR0_IM2 (1 << 2) /* Interrupt mask ep 2 */ +#define UICR0_IM3 (1 << 3) /* Interrupt mask ep 3 */ +#define UICR0_IM4 (1 << 4) /* Interrupt mask ep 4 */ +#define UICR0_IM5 (1 << 5) /* Interrupt mask ep 5 */ +#define UICR0_IM6 (1 << 6) /* Interrupt mask ep 6 */ +#define UICR0_IM7 (1 << 7) /* Interrupt mask ep 7 */ + +#define UICR1 __REG(0x40600054) /* UDC Interrupt Control Register 1 */ + +#define UICR1_IM8 (1 << 0) /* Interrupt mask ep 8 */ +#define UICR1_IM9 (1 << 1) /* Interrupt mask ep 9 */ +#define UICR1_IM10 (1 << 2) /* Interrupt mask ep 10 */ +#define UICR1_IM11 (1 << 3) /* Interrupt mask ep 11 */ +#define UICR1_IM12 (1 << 4) /* Interrupt mask ep 12 */ +#define UICR1_IM13 (1 << 5) /* Interrupt mask ep 13 */ +#define UICR1_IM14 (1 << 6) /* Interrupt mask ep 14 */ +#define UICR1_IM15 (1 << 7) /* Interrupt mask ep 15 */ + +#define USIR0 __REG(0x40600058) /* UDC Status Interrupt Register 0 */ + +#define USIR0_IR0 (1 << 0) /* Interrupt request ep 0 */ +#define USIR0_IR1 (1 << 1) /* Interrupt request ep 1 */ +#define USIR0_IR2 (1 << 2) /* Interrupt request ep 2 */ +#define USIR0_IR3 (1 << 3) /* Interrupt request ep 3 */ +#define USIR0_IR4 (1 << 4) /* Interrupt request ep 4 */ +#define USIR0_IR5 (1 << 5) /* Interrupt request ep 5 */ +#define USIR0_IR6 (1 << 6) /* Interrupt request ep 6 */ +#define USIR0_IR7 (1 << 7) /* Interrupt request ep 7 */ + +#define USIR1 __REG(0x4060005C) /* UDC Status Interrupt Register 1 */ + +#define USIR1_IR8 (1 << 0) /* Interrupt request ep 8 */ +#define USIR1_IR9 (1 << 1) /* Interrupt request ep 9 */ +#define USIR1_IR10 (1 << 2) /* Interrupt request ep 10 */ +#define USIR1_IR11 (1 << 3) /* Interrupt request ep 11 */ +#define USIR1_IR12 (1 << 4) /* Interrupt request ep 12 */ +#define USIR1_IR13 (1 << 5) /* Interrupt request ep 13 */ +#define USIR1_IR14 (1 << 6) /* Interrupt request ep 14 */ +#define USIR1_IR15 (1 << 7) /* Interrupt request ep 15 */ + +#endif diff --git a/arch/arm/mach-pxa/include/mach/pxa27x-udc.h b/arch/arm/mach-pxa/include/mach/pxa27x-udc.h new file mode 100644 index 00000000000..ab1443f8bd8 --- /dev/null +++ b/arch/arm/mach-pxa/include/mach/pxa27x-udc.h @@ -0,0 +1,257 @@ +#ifndef _ASM_ARCH_PXA27X_UDC_H +#define _ASM_ARCH_PXA27X_UDC_H + +#ifdef _ASM_ARCH_PXA25X_UDC_H +#error You cannot include both PXA25x and PXA27x UDC support +#endif + +#define UDCCR __REG(0x40600000) /* UDC Control Register */ +#define UDCCR_OEN (1 << 31) /* On-the-Go Enable */ +#define UDCCR_AALTHNP (1 << 30) /* A-device Alternate Host Negotiation + Protocol Port Support */ +#define UDCCR_AHNP (1 << 29) /* A-device Host Negotiation Protocol + Support */ +#define UDCCR_BHNP (1 << 28) /* B-device Host Negotiation Protocol + Enable */ +#define UDCCR_DWRE (1 << 16) /* Device Remote Wake-up Enable */ +#define UDCCR_ACN (0x03 << 11) /* Active UDC configuration Number */ +#define UDCCR_ACN_S 11 +#define UDCCR_AIN (0x07 << 8) /* Active UDC interface Number */ +#define UDCCR_AIN_S 8 +#define UDCCR_AAISN (0x07 << 5) /* Active UDC Alternate Interface + Setting Number */ +#define UDCCR_AAISN_S 5 +#define UDCCR_SMAC (1 << 4) /* Switch Endpoint Memory to Active + Configuration */ +#define UDCCR_EMCE (1 << 3) /* Endpoint Memory Configuration + Error */ +#define UDCCR_UDR (1 << 2) /* UDC Resume */ +#define UDCCR_UDA (1 << 1) /* UDC Active */ +#define UDCCR_UDE (1 << 0) /* UDC Enable */ + +#define UDCICR0 __REG(0x40600004) /* UDC Interrupt Control Register0 */ +#define UDCICR1 __REG(0x40600008) /* UDC Interrupt Control Register1 */ +#define UDCICR_FIFOERR (1 << 1) /* FIFO Error interrupt for EP */ +#define UDCICR_PKTCOMPL (1 << 0) /* Packet Complete interrupt for EP */ + +#define UDC_INT_FIFOERROR (0x2) +#define UDC_INT_PACKETCMP (0x1) + +#define UDCICR_INT(n,intr) (((intr) & 0x03) << (((n) & 0x0F) * 2)) +#define UDCICR1_IECC (1 << 31) /* IntEn - Configuration Change */ +#define UDCICR1_IESOF (1 << 30) /* IntEn - Start of Frame */ +#define UDCICR1_IERU (1 << 29) /* IntEn - Resume */ +#define UDCICR1_IESU (1 << 28) /* IntEn - Suspend */ +#define UDCICR1_IERS (1 << 27) /* IntEn - Reset */ + +#define UDCISR0 __REG(0x4060000C) /* UDC Interrupt Status Register 0 */ +#define UDCISR1 __REG(0x40600010) /* UDC Interrupt Status Register 1 */ +#define UDCISR_INT(n,intr) (((intr) & 0x03) << (((n) & 0x0F) * 2)) +#define UDCISR1_IRCC (1 << 31) /* IntReq - Configuration Change */ +#define UDCISR1_IRSOF (1 << 30) /* IntReq - Start of Frame */ +#define UDCISR1_IRRU (1 << 29) /* IntReq - Resume */ +#define UDCISR1_IRSU (1 << 28) /* IntReq - Suspend */ +#define UDCISR1_IRRS (1 << 27) /* IntReq - Reset */ + +#define UDCFNR __REG(0x40600014) /* UDC Frame Number Register */ +#define UDCOTGICR __REG(0x40600018) /* UDC On-The-Go interrupt control */ +#define UDCOTGICR_IESF (1 << 24) /* OTG SET_FEATURE command recvd */ +#define UDCOTGICR_IEXR (1 << 17) /* Extra Transciever Interrupt + Rising Edge Interrupt Enable */ +#define UDCOTGICR_IEXF (1 << 16) /* Extra Transciever Interrupt + Falling Edge Interrupt Enable */ +#define UDCOTGICR_IEVV40R (1 << 9) /* OTG Vbus Valid 4.0V Rising Edge + Interrupt Enable */ +#define UDCOTGICR_IEVV40F (1 << 8) /* OTG Vbus Valid 4.0V Falling Edge + Interrupt Enable */ +#define UDCOTGICR_IEVV44R (1 << 7) /* OTG Vbus Valid 4.4V Rising Edge + Interrupt Enable */ +#define UDCOTGICR_IEVV44F (1 << 6) /* OTG Vbus Valid 4.4V Falling Edge + Interrupt Enable */ +#define UDCOTGICR_IESVR (1 << 5) /* OTG Session Valid Rising Edge + Interrupt Enable */ +#define UDCOTGICR_IESVF (1 << 4) /* OTG Session Valid Falling Edge + Interrupt Enable */ +#define UDCOTGICR_IESDR (1 << 3) /* OTG A-Device SRP Detect Rising + Edge Interrupt Enable */ +#define UDCOTGICR_IESDF (1 << 2) /* OTG A-Device SRP Detect Falling + Edge Interrupt Enable */ +#define UDCOTGICR_IEIDR (1 << 1) /* OTG ID Change Rising Edge + Interrupt Enable */ +#define UDCOTGICR_IEIDF (1 << 0) /* OTG ID Change Falling Edge + Interrupt Enable */ + +#define UP2OCR __REG(0x40600020) /* USB Port 2 Output Control register */ +#define UP3OCR __REG(0x40600024) /* USB Port 2 Output Control register */ + +#define UP2OCR_CPVEN (1 << 0) /* Charge Pump Vbus Enable */ +#define UP2OCR_CPVPE (1 << 1) /* Charge Pump Vbus Pulse Enable */ +#define UP2OCR_DPPDE (1 << 2) /* Host Port 2 Transceiver D+ Pull Down Enable */ +#define UP2OCR_DMPDE (1 << 3) /* Host Port 2 Transceiver D- Pull Down Enable */ +#define UP2OCR_DPPUE (1 << 4) /* Host Port 2 Transceiver D+ Pull Up Enable */ +#define UP2OCR_DMPUE (1 << 5) /* Host Port 2 Transceiver D- Pull Up Enable */ +#define UP2OCR_DPPUBE (1 << 6) /* Host Port 2 Transceiver D+ Pull Up Bypass Enable */ +#define UP2OCR_DMPUBE (1 << 7) /* Host Port 2 Transceiver D- Pull Up Bypass Enable */ +#define UP2OCR_EXSP (1 << 8) /* External Transceiver Speed Control */ +#define UP2OCR_EXSUS (1 << 9) /* External Transceiver Speed Enable */ +#define UP2OCR_IDON (1 << 10) /* OTG ID Read Enable */ +#define UP2OCR_HXS (1 << 16) /* Host Port 2 Transceiver Output Select */ +#define UP2OCR_HXOE (1 << 17) /* Host Port 2 Transceiver Output Enable */ +#define UP2OCR_SEOS(x) ((x & 7) << 24) /* Single-Ended Output Select */ + +#define UDCCSN(x) __REG2(0x40600100, (x) << 2) +#define UDCCSR0 __REG(0x40600100) /* UDC Control/Status register - Endpoint 0 */ +#define UDCCSR0_SA (1 << 7) /* Setup Active */ +#define UDCCSR0_RNE (1 << 6) /* Receive FIFO Not Empty */ +#define UDCCSR0_FST (1 << 5) /* Force Stall */ +#define UDCCSR0_SST (1 << 4) /* Sent Stall */ +#define UDCCSR0_DME (1 << 3) /* DMA Enable */ +#define UDCCSR0_FTF (1 << 2) /* Flush Transmit FIFO */ +#define UDCCSR0_IPR (1 << 1) /* IN Packet Ready */ +#define UDCCSR0_OPC (1 << 0) /* OUT Packet Complete */ + +#define UDCCSRA __REG(0x40600104) /* UDC Control/Status register - Endpoint A */ +#define UDCCSRB __REG(0x40600108) /* UDC Control/Status register - Endpoint B */ +#define UDCCSRC __REG(0x4060010C) /* UDC Control/Status register - Endpoint C */ +#define UDCCSRD __REG(0x40600110) /* UDC Control/Status register - Endpoint D */ +#define UDCCSRE __REG(0x40600114) /* UDC Control/Status register - Endpoint E */ +#define UDCCSRF __REG(0x40600118) /* UDC Control/Status register - Endpoint F */ +#define UDCCSRG __REG(0x4060011C) /* UDC Control/Status register - Endpoint G */ +#define UDCCSRH __REG(0x40600120) /* UDC Control/Status register - Endpoint H */ +#define UDCCSRI __REG(0x40600124) /* UDC Control/Status register - Endpoint I */ +#define UDCCSRJ __REG(0x40600128) /* UDC Control/Status register - Endpoint J */ +#define UDCCSRK __REG(0x4060012C) /* UDC Control/Status register - Endpoint K */ +#define UDCCSRL __REG(0x40600130) /* UDC Control/Status register - Endpoint L */ +#define UDCCSRM __REG(0x40600134) /* UDC Control/Status register - Endpoint M */ +#define UDCCSRN __REG(0x40600138) /* UDC Control/Status register - Endpoint N */ +#define UDCCSRP __REG(0x4060013C) /* UDC Control/Status register - Endpoint P */ +#define UDCCSRQ __REG(0x40600140) /* UDC Control/Status register - Endpoint Q */ +#define UDCCSRR __REG(0x40600144) /* UDC Control/Status register - Endpoint R */ +#define UDCCSRS __REG(0x40600148) /* UDC Control/Status register - Endpoint S */ +#define UDCCSRT __REG(0x4060014C) /* UDC Control/Status register - Endpoint T */ +#define UDCCSRU __REG(0x40600150) /* UDC Control/Status register - Endpoint U */ +#define UDCCSRV __REG(0x40600154) /* UDC Control/Status register - Endpoint V */ +#define UDCCSRW __REG(0x40600158) /* UDC Control/Status register - Endpoint W */ +#define UDCCSRX __REG(0x4060015C) /* UDC Control/Status register - Endpoint X */ + +#define UDCCSR_DPE (1 << 9) /* Data Packet Error */ +#define UDCCSR_FEF (1 << 8) /* Flush Endpoint FIFO */ +#define UDCCSR_SP (1 << 7) /* Short Packet Control/Status */ +#define UDCCSR_BNE (1 << 6) /* Buffer Not Empty (IN endpoints) */ +#define UDCCSR_BNF (1 << 6) /* Buffer Not Full (OUT endpoints) */ +#define UDCCSR_FST (1 << 5) /* Force STALL */ +#define UDCCSR_SST (1 << 4) /* Sent STALL */ +#define UDCCSR_DME (1 << 3) /* DMA Enable */ +#define UDCCSR_TRN (1 << 2) /* Tx/Rx NAK */ +#define UDCCSR_PC (1 << 1) /* Packet Complete */ +#define UDCCSR_FS (1 << 0) /* FIFO needs service */ + +#define UDCBCN(x) __REG2(0x40600200, (x)<<2) +#define UDCBCR0 __REG(0x40600200) /* Byte Count Register - EP0 */ +#define UDCBCRA __REG(0x40600204) /* Byte Count Register - EPA */ +#define UDCBCRB __REG(0x40600208) /* Byte Count Register - EPB */ +#define UDCBCRC __REG(0x4060020C) /* Byte Count Register - EPC */ +#define UDCBCRD __REG(0x40600210) /* Byte Count Register - EPD */ +#define UDCBCRE __REG(0x40600214) /* Byte Count Register - EPE */ +#define UDCBCRF __REG(0x40600218) /* Byte Count Register - EPF */ +#define UDCBCRG __REG(0x4060021C) /* Byte Count Register - EPG */ +#define UDCBCRH __REG(0x40600220) /* Byte Count Register - EPH */ +#define UDCBCRI __REG(0x40600224) /* Byte Count Register - EPI */ +#define UDCBCRJ __REG(0x40600228) /* Byte Count Register - EPJ */ +#define UDCBCRK __REG(0x4060022C) /* Byte Count Register - EPK */ +#define UDCBCRL __REG(0x40600230) /* Byte Count Register - EPL */ +#define UDCBCRM __REG(0x40600234) /* Byte Count Register - EPM */ +#define UDCBCRN __REG(0x40600238) /* Byte Count Register - EPN */ +#define UDCBCRP __REG(0x4060023C) /* Byte Count Register - EPP */ +#define UDCBCRQ __REG(0x40600240) /* Byte Count Register - EPQ */ +#define UDCBCRR __REG(0x40600244) /* Byte Count Register - EPR */ +#define UDCBCRS __REG(0x40600248) /* Byte Count Register - EPS */ +#define UDCBCRT __REG(0x4060024C) /* Byte Count Register - EPT */ +#define UDCBCRU __REG(0x40600250) /* Byte Count Register - EPU */ +#define UDCBCRV __REG(0x40600254) /* Byte Count Register - EPV */ +#define UDCBCRW __REG(0x40600258) /* Byte Count Register - EPW */ +#define UDCBCRX __REG(0x4060025C) /* Byte Count Register - EPX */ + +#define UDCDN(x) __REG2(0x40600300, (x)<<2) +#define PHYS_UDCDN(x) (0x40600300 + ((x)<<2)) +#define PUDCDN(x) (volatile u32 *)(io_p2v(PHYS_UDCDN((x)))) +#define UDCDR0 __REG(0x40600300) /* Data Register - EP0 */ +#define UDCDRA __REG(0x40600304) /* Data Register - EPA */ +#define UDCDRB __REG(0x40600308) /* Data Register - EPB */ +#define UDCDRC __REG(0x4060030C) /* Data Register - EPC */ +#define UDCDRD __REG(0x40600310) /* Data Register - EPD */ +#define UDCDRE __REG(0x40600314) /* Data Register - EPE */ +#define UDCDRF __REG(0x40600318) /* Data Register - EPF */ +#define UDCDRG __REG(0x4060031C) /* Data Register - EPG */ +#define UDCDRH __REG(0x40600320) /* Data Register - EPH */ +#define UDCDRI __REG(0x40600324) /* Data Register - EPI */ +#define UDCDRJ __REG(0x40600328) /* Data Register - EPJ */ +#define UDCDRK __REG(0x4060032C) /* Data Register - EPK */ +#define UDCDRL __REG(0x40600330) /* Data Register - EPL */ +#define UDCDRM __REG(0x40600334) /* Data Register - EPM */ +#define UDCDRN __REG(0x40600338) /* Data Register - EPN */ +#define UDCDRP __REG(0x4060033C) /* Data Register - EPP */ +#define UDCDRQ __REG(0x40600340) /* Data Register - EPQ */ +#define UDCDRR __REG(0x40600344) /* Data Register - EPR */ +#define UDCDRS __REG(0x40600348) /* Data Register - EPS */ +#define UDCDRT __REG(0x4060034C) /* Data Register - EPT */ +#define UDCDRU __REG(0x40600350) /* Data Register - EPU */ +#define UDCDRV __REG(0x40600354) /* Data Register - EPV */ +#define UDCDRW __REG(0x40600358) /* Data Register - EPW */ +#define UDCDRX __REG(0x4060035C) /* Data Register - EPX */ + +#define UDCCN(x) __REG2(0x40600400, (x)<<2) +#define UDCCRA __REG(0x40600404) /* Configuration register EPA */ +#define UDCCRB __REG(0x40600408) /* Configuration register EPB */ +#define UDCCRC __REG(0x4060040C) /* Configuration register EPC */ +#define UDCCRD __REG(0x40600410) /* Configuration register EPD */ +#define UDCCRE __REG(0x40600414) /* Configuration register EPE */ +#define UDCCRF __REG(0x40600418) /* Configuration register EPF */ +#define UDCCRG __REG(0x4060041C) /* Configuration register EPG */ +#define UDCCRH __REG(0x40600420) /* Configuration register EPH */ +#define UDCCRI __REG(0x40600424) /* Configuration register EPI */ +#define UDCCRJ __REG(0x40600428) /* Configuration register EPJ */ +#define UDCCRK __REG(0x4060042C) /* Configuration register EPK */ +#define UDCCRL __REG(0x40600430) /* Configuration register EPL */ +#define UDCCRM __REG(0x40600434) /* Configuration register EPM */ +#define UDCCRN __REG(0x40600438) /* Configuration register EPN */ +#define UDCCRP __REG(0x4060043C) /* Configuration register EPP */ +#define UDCCRQ __REG(0x40600440) /* Configuration register EPQ */ +#define UDCCRR __REG(0x40600444) /* Configuration register EPR */ +#define UDCCRS __REG(0x40600448) /* Configuration register EPS */ +#define UDCCRT __REG(0x4060044C) /* Configuration register EPT */ +#define UDCCRU __REG(0x40600450) /* Configuration register EPU */ +#define UDCCRV __REG(0x40600454) /* Configuration register EPV */ +#define UDCCRW __REG(0x40600458) /* Configuration register EPW */ +#define UDCCRX __REG(0x4060045C) /* Configuration register EPX */ + +#define UDCCONR_CN (0x03 << 25) /* Configuration Number */ +#define UDCCONR_CN_S (25) +#define UDCCONR_IN (0x07 << 22) /* Interface Number */ +#define UDCCONR_IN_S (22) +#define UDCCONR_AISN (0x07 << 19) /* Alternate Interface Number */ +#define UDCCONR_AISN_S (19) +#define UDCCONR_EN (0x0f << 15) /* Endpoint Number */ +#define UDCCONR_EN_S (15) +#define UDCCONR_ET (0x03 << 13) /* Endpoint Type: */ +#define UDCCONR_ET_S (13) +#define UDCCONR_ET_INT (0x03 << 13) /* Interrupt */ +#define UDCCONR_ET_BULK (0x02 << 13) /* Bulk */ +#define UDCCONR_ET_ISO (0x01 << 13) /* Isochronous */ +#define UDCCONR_ET_NU (0x00 << 13) /* Not used */ +#define UDCCONR_ED (1 << 12) /* Endpoint Direction */ +#define UDCCONR_MPS (0x3ff << 2) /* Maximum Packet Size */ +#define UDCCONR_MPS_S (2) +#define UDCCONR_DE (1 << 1) /* Double Buffering Enable */ +#define UDCCONR_EE (1 << 0) /* Endpoint Enable */ + + +#define UDC_INT_FIFOERROR (0x2) +#define UDC_INT_PACKETCMP (0x1) + +#define UDC_FNR_MASK (0x7ff) + +#define UDCCSR_WR_MASK (UDCCSR_DME|UDCCSR_FST) +#define UDC_BCR_MASK (0x3ff) + +#endif diff --git a/arch/arm/mach-pxa/include/mach/pxa27x_keypad.h b/arch/arm/mach-pxa/include/mach/pxa27x_keypad.h new file mode 100644 index 00000000000..d5a48a96dea --- /dev/null +++ b/arch/arm/mach-pxa/include/mach/pxa27x_keypad.h @@ -0,0 +1,58 @@ +#ifndef __ASM_ARCH_PXA27x_KEYPAD_H +#define __ASM_ARCH_PXA27x_KEYPAD_H + +#include <linux/input.h> + +#define MAX_MATRIX_KEY_ROWS (8) +#define MAX_MATRIX_KEY_COLS (8) + +/* pxa3xx keypad platform specific parameters + * + * NOTE: + * 1. direct_key_num indicates the number of keys in the direct keypad + * _plus_ the number of rotary-encoder sensor inputs, this can be + * left as 0 if only rotary encoders are enabled, the driver will + * automatically calculate this + * + * 2. direct_key_map is the key code map for the direct keys, if rotary + * encoder(s) are enabled, direct key 0/1(2/3) will be ignored + * + * 3. rotary can be either interpreted as a relative input event (e.g. + * REL_WHEEL/REL_HWHEEL) or specific keys (e.g. UP/DOWN/LEFT/RIGHT) + * + * 4. matrix key and direct key will use the same debounce_interval by + * default, which should be sufficient in most cases + */ +struct pxa27x_keypad_platform_data { + + /* code map for the matrix keys */ + unsigned int matrix_key_rows; + unsigned int matrix_key_cols; + unsigned int *matrix_key_map; + int matrix_key_map_size; + + /* direct keys */ + int direct_key_num; + unsigned int direct_key_map[8]; + + /* rotary encoders 0 */ + int enable_rotary0; + int rotary0_rel_code; + int rotary0_up_key; + int rotary0_down_key; + + /* rotary encoders 1 */ + int enable_rotary1; + int rotary1_rel_code; + int rotary1_up_key; + int rotary1_down_key; + + /* key debounce interval */ + unsigned int debounce_interval; +}; + +#define KEY(row, col, val) (((row) << 28) | ((col) << 24) | (val)) + +extern void pxa_set_keypad_info(struct pxa27x_keypad_platform_data *info); + +#endif /* __ASM_ARCH_PXA27x_KEYPAD_H */ diff --git a/arch/arm/mach-pxa/include/mach/pxa2xx-gpio.h b/arch/arm/mach-pxa/include/mach/pxa2xx-gpio.h new file mode 100644 index 00000000000..6ef1dd09970 --- /dev/null +++ b/arch/arm/mach-pxa/include/mach/pxa2xx-gpio.h @@ -0,0 +1,368 @@ +#ifndef __ASM_ARCH_PXA2XX_GPIO_H +#define __ASM_ARCH_PXA2XX_GPIO_H + +#warning Please use mfp-pxa2[57]x.h instead of pxa2xx-gpio.h + +/* GPIO alternate function assignments */ + +#define GPIO1_RST 1 /* reset */ +#define GPIO6_MMCCLK 6 /* MMC Clock */ +#define GPIO7_48MHz 7 /* 48 MHz clock output */ +#define GPIO8_MMCCS0 8 /* MMC Chip Select 0 */ +#define GPIO9_MMCCS1 9 /* MMC Chip Select 1 */ +#define GPIO10_RTCCLK 10 /* real time clock (1 Hz) */ +#define GPIO11_3_6MHz 11 /* 3.6 MHz oscillator out */ +#define GPIO12_32KHz 12 /* 32 kHz out */ +#define GPIO12_CIF_DD_7 12 /* Camera data pin 7 */ +#define GPIO13_MBGNT 13 /* memory controller grant */ +#define GPIO14_MBREQ 14 /* alternate bus master request */ +#define GPIO15_nCS_1 15 /* chip select 1 */ +#define GPIO16_PWM0 16 /* PWM0 output */ +#define GPIO17_PWM1 17 /* PWM1 output */ +#define GPIO17_CIF_DD_6 17 /* Camera data pin 6 */ +#define GPIO18_RDY 18 /* Ext. Bus Ready */ +#define GPIO19_DREQ1 19 /* External DMA Request */ +#define GPIO20_DREQ0 20 /* External DMA Request */ +#define GPIO23_SCLK 23 /* SSP clock */ +#define GPIO23_CIF_MCLK 23 /* Camera Master Clock */ +#define GPIO24_SFRM 24 /* SSP Frame */ +#define GPIO24_CIF_FV 24 /* Camera frame start signal */ +#define GPIO25_STXD 25 /* SSP transmit */ +#define GPIO25_CIF_LV 25 /* Camera line start signal */ +#define GPIO26_SRXD 26 /* SSP receive */ +#define GPIO26_CIF_PCLK 26 /* Camera Pixel Clock */ +#define GPIO27_SEXTCLK 27 /* SSP ext_clk */ +#define GPIO27_CIF_DD_0 27 /* Camera data pin 0 */ +#define GPIO28_BITCLK 28 /* AC97/I2S bit_clk */ +#define GPIO29_SDATA_IN 29 /* AC97 Sdata_in0 / I2S Sdata_in */ +#define GPIO30_SDATA_OUT 30 /* AC97/I2S Sdata_out */ +#define GPIO31_SYNC 31 /* AC97/I2S sync */ +#define GPIO32_SDATA_IN1 32 /* AC97 Sdata_in1 */ +#define GPIO32_SYSCLK 32 /* I2S System Clock */ +#define GPIO32_MMCCLK 32 /* MMC Clock (PXA270) */ +#define GPIO33_nCS_5 33 /* chip select 5 */ +#define GPIO34_FFRXD 34 /* FFUART receive */ +#define GPIO34_MMCCS0 34 /* MMC Chip Select 0 */ +#define GPIO35_FFCTS 35 /* FFUART Clear to send */ +#define GPIO36_FFDCD 36 /* FFUART Data carrier detect */ +#define GPIO37_FFDSR 37 /* FFUART data set ready */ +#define GPIO38_FFRI 38 /* FFUART Ring Indicator */ +#define GPIO39_MMCCS1 39 /* MMC Chip Select 1 */ +#define GPIO39_FFTXD 39 /* FFUART transmit data */ +#define GPIO40_FFDTR 40 /* FFUART data terminal Ready */ +#define GPIO41_FFRTS 41 /* FFUART request to send */ +#define GPIO42_BTRXD 42 /* BTUART receive data */ +#define GPIO42_HWRXD 42 /* HWUART receive data */ +#define GPIO42_CIF_MCLK 42 /* Camera Master Clock */ +#define GPIO43_BTTXD 43 /* BTUART transmit data */ +#define GPIO43_HWTXD 43 /* HWUART transmit data */ +#define GPIO43_CIF_FV 43 /* Camera frame start signal */ +#define GPIO44_BTCTS 44 /* BTUART clear to send */ +#define GPIO44_HWCTS 44 /* HWUART clear to send */ +#define GPIO44_CIF_LV 44 /* Camera line start signal */ +#define GPIO45_BTRTS 45 /* BTUART request to send */ +#define GPIO45_HWRTS 45 /* HWUART request to send */ +#define GPIO45_AC97_SYSCLK 45 /* AC97 System Clock */ +#define GPIO45_CIF_PCLK 45 /* Camera Pixel Clock */ +#define GPIO46_ICPRXD 46 /* ICP receive data */ +#define GPIO46_STRXD 46 /* STD_UART receive data */ +#define GPIO47_ICPTXD 47 /* ICP transmit data */ +#define GPIO47_STTXD 47 /* STD_UART transmit data */ +#define GPIO47_CIF_DD_0 47 /* Camera data pin 0 */ +#define GPIO48_nPOE 48 /* Output Enable for Card Space */ +#define GPIO48_CIF_DD_5 48 /* Camera data pin 5 */ +#define GPIO49_nPWE 49 /* Write Enable for Card Space */ +#define GPIO50_nPIOR 50 /* I/O Read for Card Space */ +#define GPIO50_CIF_DD_3 50 /* Camera data pin 3 */ +#define GPIO51_nPIOW 51 /* I/O Write for Card Space */ +#define GPIO51_CIF_DD_2 51 /* Camera data pin 2 */ +#define GPIO52_nPCE_1 52 /* Card Enable for Card Space */ +#define GPIO52_CIF_DD_4 52 /* Camera data pin 4 */ +#define GPIO53_nPCE_2 53 /* Card Enable for Card Space */ +#define GPIO53_MMCCLK 53 /* MMC Clock */ +#define GPIO53_CIF_MCLK 53 /* Camera Master Clock */ +#define GPIO54_MMCCLK 54 /* MMC Clock */ +#define GPIO54_pSKTSEL 54 /* Socket Select for Card Space */ +#define GPIO54_nPCE_2 54 /* Card Enable for Card Space (PXA27x) */ +#define GPIO54_CIF_PCLK 54 /* Camera Pixel Clock */ +#define GPIO55_nPREG 55 /* Card Address bit 26 */ +#define GPIO55_CIF_DD_1 55 /* Camera data pin 1 */ +#define GPIO56_nPWAIT 56 /* Wait signal for Card Space */ +#define GPIO57_nIOIS16 57 /* Bus Width select for I/O Card Space */ +#define GPIO58_LDD_0 58 /* LCD data pin 0 */ +#define GPIO59_LDD_1 59 /* LCD data pin 1 */ +#define GPIO60_LDD_2 60 /* LCD data pin 2 */ +#define GPIO61_LDD_3 61 /* LCD data pin 3 */ +#define GPIO62_LDD_4 62 /* LCD data pin 4 */ +#define GPIO63_LDD_5 63 /* LCD data pin 5 */ +#define GPIO64_LDD_6 64 /* LCD data pin 6 */ +#define GPIO65_LDD_7 65 /* LCD data pin 7 */ +#define GPIO66_LDD_8 66 /* LCD data pin 8 */ +#define GPIO66_MBREQ 66 /* alternate bus master req */ +#define GPIO67_LDD_9 67 /* LCD data pin 9 */ +#define GPIO67_MMCCS0 67 /* MMC Chip Select 0 */ +#define GPIO68_LDD_10 68 /* LCD data pin 10 */ +#define GPIO68_MMCCS1 68 /* MMC Chip Select 1 */ +#define GPIO69_LDD_11 69 /* LCD data pin 11 */ +#define GPIO69_MMCCLK 69 /* MMC_CLK */ +#define GPIO70_LDD_12 70 /* LCD data pin 12 */ +#define GPIO70_RTCCLK 70 /* Real Time clock (1 Hz) */ +#define GPIO71_LDD_13 71 /* LCD data pin 13 */ +#define GPIO71_3_6MHz 71 /* 3.6 MHz Oscillator clock */ +#define GPIO72_LDD_14 72 /* LCD data pin 14 */ +#define GPIO72_32kHz 72 /* 32 kHz clock */ +#define GPIO73_LDD_15 73 /* LCD data pin 15 */ +#define GPIO73_MBGNT 73 /* Memory controller grant */ +#define GPIO74_LCD_FCLK 74 /* LCD Frame clock */ +#define GPIO75_LCD_LCLK 75 /* LCD line clock */ +#define GPIO76_LCD_PCLK 76 /* LCD Pixel clock */ +#define GPIO77_LCD_ACBIAS 77 /* LCD AC Bias */ +#define GPIO78_nCS_2 78 /* chip select 2 */ +#define GPIO79_nCS_3 79 /* chip select 3 */ +#define GPIO80_nCS_4 80 /* chip select 4 */ +#define GPIO81_NSCLK 81 /* NSSP clock */ +#define GPIO81_CIF_DD_0 81 /* Camera data pin 0 */ +#define GPIO82_NSFRM 82 /* NSSP Frame */ +#define GPIO82_CIF_DD_5 82 /* Camera data pin 5 */ +#define GPIO83_NSTXD 83 /* NSSP transmit */ +#define GPIO83_CIF_DD_4 83 /* Camera data pin 4 */ +#define GPIO84_NSRXD 84 /* NSSP receive */ +#define GPIO84_CIF_FV 84 /* Camera frame start signal */ +#define GPIO85_nPCE_1 85 /* Card Enable for Card Space (PXA27x) */ +#define GPIO85_CIF_LV 85 /* Camera line start signal */ +#define GPIO90_CIF_DD_4 90 /* Camera data pin 4 */ +#define GPIO91_CIF_DD_5 91 /* Camera data pin 5 */ +#define GPIO92_MMCDAT0 92 /* MMC DAT0 (PXA27x) */ +#define GPIO93_CIF_DD_6 93 /* Camera data pin 6 */ +#define GPIO94_CIF_DD_5 94 /* Camera data pin 5 */ +#define GPIO95_CIF_DD_4 95 /* Camera data pin 4 */ +#define GPIO96_FFRXD 96 /* FFUART recieve */ +#define GPIO98_FFRTS 98 /* FFUART request to send */ +#define GPIO98_CIF_DD_0 98 /* Camera data pin 0 */ +#define GPIO99_FFTXD 99 /* FFUART transmit data */ +#define GPIO100_FFCTS 100 /* FFUART Clear to send */ +#define GPIO102_nPCE_1 102 /* PCMCIA (PXA27x) */ +#define GPIO103_CIF_DD_3 103 /* Camera data pin 3 */ +#define GPIO104_CIF_DD_2 104 /* Camera data pin 2 */ +#define GPIO105_CIF_DD_1 105 /* Camera data pin 1 */ +#define GPIO106_CIF_DD_9 106 /* Camera data pin 9 */ +#define GPIO107_CIF_DD_8 107 /* Camera data pin 8 */ +#define GPIO108_CIF_DD_7 108 /* Camera data pin 7 */ +#define GPIO109_MMCDAT1 109 /* MMC DAT1 (PXA27x) */ +#define GPIO110_MMCDAT2 110 /* MMC DAT2 (PXA27x) */ +#define GPIO110_MMCCS0 110 /* MMC Chip Select 0 (PXA27x) */ +#define GPIO111_MMCDAT3 111 /* MMC DAT3 (PXA27x) */ +#define GPIO111_MMCCS1 111 /* MMC Chip Select 1 (PXA27x) */ +#define GPIO112_MMCCMD 112 /* MMC CMD (PXA27x) */ +#define GPIO113_I2S_SYSCLK 113 /* I2S System Clock (PXA27x) */ +#define GPIO113_AC97_RESET_N 113 /* AC97 NRESET on (PXA27x) */ +#define GPIO114_CIF_DD_1 114 /* Camera data pin 1 */ +#define GPIO115_CIF_DD_3 115 /* Camera data pin 3 */ +#define GPIO116_CIF_DD_2 116 /* Camera data pin 2 */ + +/* GPIO alternate function mode & direction */ + +#define GPIO_IN 0x000 +#define GPIO_OUT 0x080 +#define GPIO_ALT_FN_1_IN 0x100 +#define GPIO_ALT_FN_1_OUT 0x180 +#define GPIO_ALT_FN_2_IN 0x200 +#define GPIO_ALT_FN_2_OUT 0x280 +#define GPIO_ALT_FN_3_IN 0x300 +#define GPIO_ALT_FN_3_OUT 0x380 +#define GPIO_MD_MASK_NR 0x07f +#define GPIO_MD_MASK_DIR 0x080 +#define GPIO_MD_MASK_FN 0x300 +#define GPIO_DFLT_LOW 0x400 +#define GPIO_DFLT_HIGH 0x800 + +#define GPIO1_RTS_MD ( 1 | GPIO_ALT_FN_1_IN) +#define GPIO6_MMCCLK_MD ( 6 | GPIO_ALT_FN_1_OUT) +#define GPIO7_48MHz_MD ( 7 | GPIO_ALT_FN_1_OUT) +#define GPIO8_MMCCS0_MD ( 8 | GPIO_ALT_FN_1_OUT) +#define GPIO9_MMCCS1_MD ( 9 | GPIO_ALT_FN_1_OUT) +#define GPIO10_RTCCLK_MD (10 | GPIO_ALT_FN_1_OUT) +#define GPIO11_3_6MHz_MD (11 | GPIO_ALT_FN_1_OUT) +#define GPIO12_32KHz_MD (12 | GPIO_ALT_FN_1_OUT) +#define GPIO12_CIF_DD_7_MD (12 | GPIO_ALT_FN_2_IN) +#define GPIO13_MBGNT_MD (13 | GPIO_ALT_FN_2_OUT) +#define GPIO14_MBREQ_MD (14 | GPIO_ALT_FN_1_IN) +#define GPIO15_nCS_1_MD (15 | GPIO_ALT_FN_2_OUT) +#define GPIO16_PWM0_MD (16 | GPIO_ALT_FN_2_OUT) +#define GPIO17_PWM1_MD (17 | GPIO_ALT_FN_2_OUT) +#define GPIO17_CIF_DD_6_MD (17 | GPIO_ALT_FN_2_IN) +#define GPIO18_RDY_MD (18 | GPIO_ALT_FN_1_IN) +#define GPIO19_DREQ1_MD (19 | GPIO_ALT_FN_1_IN) +#define GPIO20_DREQ0_MD (20 | GPIO_ALT_FN_1_IN) +#define GPIO23_CIF_MCLK_MD (23 | GPIO_ALT_FN_1_OUT) +#define GPIO23_SCLK_MD (23 | GPIO_ALT_FN_2_OUT) +#define GPIO24_CIF_FV_MD (24 | GPIO_ALT_FN_1_OUT) +#define GPIO24_SFRM_MD (24 | GPIO_ALT_FN_2_OUT) +#define GPIO25_CIF_LV_MD (25 | GPIO_ALT_FN_1_OUT) +#define GPIO25_STXD_MD (25 | GPIO_ALT_FN_2_OUT) +#define GPIO26_SRXD_MD (26 | GPIO_ALT_FN_1_IN) +#define GPIO26_CIF_PCLK_MD (26 | GPIO_ALT_FN_2_IN) +#define GPIO27_SEXTCLK_MD (27 | GPIO_ALT_FN_1_IN) +#define GPIO27_CIF_DD_0_MD (27 | GPIO_ALT_FN_3_IN) +#define GPIO28_BITCLK_AC97_MD (28 | GPIO_ALT_FN_1_IN) +#define GPIO28_BITCLK_IN_I2S_MD (28 | GPIO_ALT_FN_2_IN) +#define GPIO28_BITCLK_OUT_I2S_MD (28 | GPIO_ALT_FN_1_OUT) +#define GPIO29_SDATA_IN_AC97_MD (29 | GPIO_ALT_FN_1_IN) +#define GPIO29_SDATA_IN_I2S_MD (29 | GPIO_ALT_FN_2_IN) +#define GPIO30_SDATA_OUT_AC97_MD (30 | GPIO_ALT_FN_2_OUT) +#define GPIO30_SDATA_OUT_I2S_MD (30 | GPIO_ALT_FN_1_OUT) +#define GPIO31_SYNC_I2S_MD (31 | GPIO_ALT_FN_1_OUT) +#define GPIO31_SYNC_AC97_MD (31 | GPIO_ALT_FN_2_OUT) +#define GPIO32_SDATA_IN1_AC97_MD (32 | GPIO_ALT_FN_1_IN) +#define GPIO32_SYSCLK_I2S_MD (32 | GPIO_ALT_FN_1_OUT) +#define GPIO32_MMCCLK_MD (32 | GPIO_ALT_FN_2_OUT) +#define GPIO33_nCS_5_MD (33 | GPIO_ALT_FN_2_OUT) +#define GPIO34_FFRXD_MD (34 | GPIO_ALT_FN_1_IN) +#define GPIO34_MMCCS0_MD (34 | GPIO_ALT_FN_2_OUT) +#define GPIO35_FFCTS_MD (35 | GPIO_ALT_FN_1_IN) +#define GPIO35_KP_MKOUT6_MD (35 | GPIO_ALT_FN_2_OUT) +#define GPIO36_FFDCD_MD (36 | GPIO_ALT_FN_1_IN) +#define GPIO37_FFDSR_MD (37 | GPIO_ALT_FN_1_IN) +#define GPIO38_FFRI_MD (38 | GPIO_ALT_FN_1_IN) +#define GPIO39_MMCCS1_MD (39 | GPIO_ALT_FN_1_OUT) +#define GPIO39_FFTXD_MD (39 | GPIO_ALT_FN_2_OUT) +#define GPIO40_FFDTR_MD (40 | GPIO_ALT_FN_2_OUT) +#define GPIO41_FFRTS_MD (41 | GPIO_ALT_FN_2_OUT) +#define GPIO41_KP_MKOUT7_MD (41 | GPIO_ALT_FN_1_OUT) +#define GPIO42_BTRXD_MD (42 | GPIO_ALT_FN_1_IN) +#define GPIO42_HWRXD_MD (42 | GPIO_ALT_FN_3_IN) +#define GPIO42_CIF_MCLK_MD (42 | GPIO_ALT_FN_3_OUT) +#define GPIO43_BTTXD_MD (43 | GPIO_ALT_FN_2_OUT) +#define GPIO43_HWTXD_MD (43 | GPIO_ALT_FN_3_OUT) +#define GPIO43_CIF_FV_MD (43 | GPIO_ALT_FN_3_OUT) +#define GPIO44_BTCTS_MD (44 | GPIO_ALT_FN_1_IN) +#define GPIO44_HWCTS_MD (44 | GPIO_ALT_FN_3_IN) +#define GPIO44_CIF_LV_MD (44 | GPIO_ALT_FN_3_OUT) +#define GPIO45_CIF_PCLK_MD (45 | GPIO_ALT_FN_3_IN) +#define GPIO45_BTRTS_MD (45 | GPIO_ALT_FN_2_OUT) +#define GPIO45_HWRTS_MD (45 | GPIO_ALT_FN_3_OUT) +#define GPIO45_SYSCLK_AC97_MD (45 | GPIO_ALT_FN_1_OUT) +#define GPIO46_ICPRXD_MD (46 | GPIO_ALT_FN_1_IN) +#define GPIO46_STRXD_MD (46 | GPIO_ALT_FN_2_IN) +#define GPIO47_CIF_DD_0_MD (47 | GPIO_ALT_FN_1_IN) +#define GPIO47_ICPTXD_MD (47 | GPIO_ALT_FN_2_OUT) +#define GPIO47_STTXD_MD (47 | GPIO_ALT_FN_1_OUT) +#define GPIO48_CIF_DD_5_MD (48 | GPIO_ALT_FN_1_IN) +#define GPIO48_nPOE_MD (48 | GPIO_ALT_FN_2_OUT) +#define GPIO48_HWTXD_MD (48 | GPIO_ALT_FN_1_OUT) +#define GPIO48_nPOE_MD (48 | GPIO_ALT_FN_2_OUT) +#define GPIO49_HWRXD_MD (49 | GPIO_ALT_FN_1_IN) +#define GPIO49_nPWE_MD (49 | GPIO_ALT_FN_2_OUT) +#define GPIO50_CIF_DD_3_MD (50 | GPIO_ALT_FN_1_IN) +#define GPIO50_nPIOR_MD (50 | GPIO_ALT_FN_2_OUT) +#define GPIO50_HWCTS_MD (50 | GPIO_ALT_FN_1_IN) +#define GPIO50_CIF_DD_3_MD (50 | GPIO_ALT_FN_1_IN) +#define GPIO51_CIF_DD_2_MD (51 | GPIO_ALT_FN_1_IN) +#define GPIO51_nPIOW_MD (51 | GPIO_ALT_FN_2_OUT) +#define GPIO51_HWRTS_MD (51 | GPIO_ALT_FN_1_OUT) +#define GPIO51_CIF_DD_2_MD (51 | GPIO_ALT_FN_1_IN) +#define GPIO52_nPCE_1_MD (52 | GPIO_ALT_FN_2_OUT) +#define GPIO52_CIF_DD_4_MD (52 | GPIO_ALT_FN_1_IN) +#define GPIO53_nPCE_2_MD (53 | GPIO_ALT_FN_2_OUT) +#define GPIO53_MMCCLK_MD (53 | GPIO_ALT_FN_1_OUT) +#define GPIO53_CIF_MCLK_MD (53 | GPIO_ALT_FN_2_OUT) +#define GPIO54_MMCCLK_MD (54 | GPIO_ALT_FN_1_OUT) +#define GPIO54_nPCE_2_MD (54 | GPIO_ALT_FN_2_OUT) +#define GPIO54_pSKTSEL_MD (54 | GPIO_ALT_FN_2_OUT) +#define GPIO54_CIF_PCLK_MD (54 | GPIO_ALT_FN_3_IN) +#define GPIO55_nPREG_MD (55 | GPIO_ALT_FN_2_OUT) +#define GPIO55_CIF_DD_1_MD (55 | GPIO_ALT_FN_1_IN) +#define GPIO56_nPWAIT_MD (56 | GPIO_ALT_FN_1_IN) +#define GPIO57_nIOIS16_MD (57 | GPIO_ALT_FN_1_IN) +#define GPIO58_LDD_0_MD (58 | GPIO_ALT_FN_2_OUT) +#define GPIO59_LDD_1_MD (59 | GPIO_ALT_FN_2_OUT) +#define GPIO60_LDD_2_MD (60 | GPIO_ALT_FN_2_OUT) +#define GPIO61_LDD_3_MD (61 | GPIO_ALT_FN_2_OUT) +#define GPIO62_LDD_4_MD (62 | GPIO_ALT_FN_2_OUT) +#define GPIO63_LDD_5_MD (63 | GPIO_ALT_FN_2_OUT) +#define GPIO64_LDD_6_MD (64 | GPIO_ALT_FN_2_OUT) +#define GPIO65_LDD_7_MD (65 | GPIO_ALT_FN_2_OUT) +#define GPIO66_LDD_8_MD (66 | GPIO_ALT_FN_2_OUT) +#define GPIO66_MBREQ_MD (66 | GPIO_ALT_FN_1_IN) +#define GPIO67_LDD_9_MD (67 | GPIO_ALT_FN_2_OUT) +#define GPIO67_MMCCS0_MD (67 | GPIO_ALT_FN_1_OUT) +#define GPIO68_LDD_10_MD (68 | GPIO_ALT_FN_2_OUT) +#define GPIO68_MMCCS1_MD (68 | GPIO_ALT_FN_1_OUT) +#define GPIO69_LDD_11_MD (69 | GPIO_ALT_FN_2_OUT) +#define GPIO69_MMCCLK_MD (69 | GPIO_ALT_FN_1_OUT) +#define GPIO70_LDD_12_MD (70 | GPIO_ALT_FN_2_OUT) +#define GPIO70_RTCCLK_MD (70 | GPIO_ALT_FN_1_OUT) +#define GPIO71_LDD_13_MD (71 | GPIO_ALT_FN_2_OUT) +#define GPIO71_3_6MHz_MD (71 | GPIO_ALT_FN_1_OUT) +#define GPIO72_LDD_14_MD (72 | GPIO_ALT_FN_2_OUT) +#define GPIO72_32kHz_MD (72 | GPIO_ALT_FN_1_OUT) +#define GPIO73_LDD_15_MD (73 | GPIO_ALT_FN_2_OUT) +#define GPIO73_MBGNT_MD (73 | GPIO_ALT_FN_1_OUT) +#define GPIO74_LCD_FCLK_MD (74 | GPIO_ALT_FN_2_OUT) +#define GPIO75_LCD_LCLK_MD (75 | GPIO_ALT_FN_2_OUT) +#define GPIO76_LCD_PCLK_MD (76 | GPIO_ALT_FN_2_OUT) +#define GPIO77_LCD_ACBIAS_MD (77 | GPIO_ALT_FN_2_OUT) +#define GPIO78_nCS_2_MD (78 | GPIO_ALT_FN_2_OUT) +#define GPIO78_nPCE_2_MD (78 | GPIO_ALT_FN_1_OUT) +#define GPIO79_nCS_3_MD (79 | GPIO_ALT_FN_2_OUT) +#define GPIO79_pSKTSEL_MD (79 | GPIO_ALT_FN_1_OUT) +#define GPIO80_nCS_4_MD (80 | GPIO_ALT_FN_2_OUT) +#define GPIO81_NSSP_CLK_OUT (81 | GPIO_ALT_FN_1_OUT) +#define GPIO81_NSSP_CLK_IN (81 | GPIO_ALT_FN_1_IN) +#define GPIO81_CIF_DD_0_MD (81 | GPIO_ALT_FN_2_IN) +#define GPIO82_NSSP_FRM_OUT (82 | GPIO_ALT_FN_1_OUT) +#define GPIO82_NSSP_FRM_IN (82 | GPIO_ALT_FN_1_IN) +#define GPIO82_CIF_DD_5_MD (82 | GPIO_ALT_FN_3_IN) +#define GPIO83_NSSP_TX (83 | GPIO_ALT_FN_1_OUT) +#define GPIO83_NSSP_RX (83 | GPIO_ALT_FN_2_IN) +#define GPIO83_CIF_DD_4_MD (83 | GPIO_ALT_FN_3_IN) +#define GPIO84_NSSP_TX (84 | GPIO_ALT_FN_1_OUT) +#define GPIO84_NSSP_RX (84 | GPIO_ALT_FN_2_IN) +#define GPIO84_CIF_FV_MD (84 | GPIO_ALT_FN_3_IN) +#define GPIO85_nPCE_1_MD (85 | GPIO_ALT_FN_1_OUT) +#define GPIO85_CIF_LV_MD (85 | GPIO_ALT_FN_3_IN) +#define GPIO86_nPCE_1_MD (86 | GPIO_ALT_FN_1_OUT) +#define GPIO88_USBH1_PWR_MD (88 | GPIO_ALT_FN_1_IN) +#define GPIO89_USBH1_PEN_MD (89 | GPIO_ALT_FN_2_OUT) +#define GPIO90_CIF_DD_4_MD (90 | GPIO_ALT_FN_3_IN) +#define GPIO91_CIF_DD_5_MD (91 | GPIO_ALT_FN_3_IN) +#define GPIO92_MMCDAT0_MD (92 | GPIO_ALT_FN_1_OUT) +#define GPIO93_CIF_DD_6_MD (93 | GPIO_ALT_FN_2_IN) +#define GPIO94_CIF_DD_5_MD (94 | GPIO_ALT_FN_2_IN) +#define GPIO95_CIF_DD_4_MD (95 | GPIO_ALT_FN_2_IN) +#define GPIO95_KP_MKIN6_MD (95 | GPIO_ALT_FN_3_IN) +#define GPIO96_KP_DKIN3_MD (96 | GPIO_ALT_FN_1_IN) +#define GPIO96_FFRXD_MD (96 | GPIO_ALT_FN_3_IN) +#define GPIO97_KP_MKIN3_MD (97 | GPIO_ALT_FN_3_IN) +#define GPIO98_CIF_DD_0_MD (98 | GPIO_ALT_FN_2_IN) +#define GPIO98_FFRTS_MD (98 | GPIO_ALT_FN_3_OUT) +#define GPIO99_FFTXD_MD (99 | GPIO_ALT_FN_3_OUT) +#define GPIO100_KP_MKIN0_MD (100 | GPIO_ALT_FN_1_IN) +#define GPIO101_KP_MKIN1_MD (101 | GPIO_ALT_FN_1_IN) +#define GPIO102_nPCE_1_MD (102 | GPIO_ALT_FN_1_OUT) +#define GPIO102_KP_MKIN2_MD (102 | GPIO_ALT_FN_1_IN) +#define GPIO103_CIF_DD_3_MD (103 | GPIO_ALT_FN_1_IN) +#define GPIO103_KP_MKOUT0_MD (103 | GPIO_ALT_FN_2_OUT) +#define GPIO104_CIF_DD_2_MD (104 | GPIO_ALT_FN_1_IN) +#define GPIO104_pSKTSEL_MD (104 | GPIO_ALT_FN_1_OUT) +#define GPIO104_KP_MKOUT1_MD (104 | GPIO_ALT_FN_2_OUT) +#define GPIO105_CIF_DD_1_MD (105 | GPIO_ALT_FN_1_IN) +#define GPIO105_KP_MKOUT2_MD (105 | GPIO_ALT_FN_2_OUT) +#define GPIO106_CIF_DD_9_MD (106 | GPIO_ALT_FN_1_IN) +#define GPIO106_KP_MKOUT3_MD (106 | GPIO_ALT_FN_2_OUT) +#define GPIO107_CIF_DD_8_MD (107 | GPIO_ALT_FN_1_IN) +#define GPIO107_KP_MKOUT4_MD (107 | GPIO_ALT_FN_2_OUT) +#define GPIO108_CIF_DD_7_MD (108 | GPIO_ALT_FN_1_IN) +#define GPIO108_KP_MKOUT5_MD (108 | GPIO_ALT_FN_2_OUT) +#define GPIO109_MMCDAT1_MD (109 | GPIO_ALT_FN_1_OUT) +#define GPIO110_MMCDAT2_MD (110 | GPIO_ALT_FN_1_OUT) +#define GPIO110_MMCCS0_MD (110 | GPIO_ALT_FN_1_OUT) +#define GPIO111_MMCDAT3_MD (111 | GPIO_ALT_FN_1_OUT) +#define GPIO110_MMCCS1_MD (111 | GPIO_ALT_FN_1_OUT) +#define GPIO112_MMCCMD_MD (112 | GPIO_ALT_FN_1_OUT) +#define GPIO113_I2S_SYSCLK_MD (113 | GPIO_ALT_FN_1_OUT) +#define GPIO113_AC97_RESET_N_MD (113 | GPIO_ALT_FN_2_OUT) +#define GPIO117_I2CSCL_MD (117 | GPIO_ALT_FN_1_IN) +#define GPIO118_I2CSDA_MD (118 | GPIO_ALT_FN_1_IN) + +#endif /* __ASM_ARCH_PXA2XX_GPIO_H */ diff --git a/arch/arm/mach-pxa/include/mach/pxa2xx-regs.h b/arch/arm/mach-pxa/include/mach/pxa2xx-regs.h new file mode 100644 index 00000000000..806ecfea44b --- /dev/null +++ b/arch/arm/mach-pxa/include/mach/pxa2xx-regs.h @@ -0,0 +1,246 @@ +/* + * arch/arm/mach-pxa/include/mach/pxa2xx-regs.h + * + * Taken from pxa-regs.h by Russell King + * + * Author: Nicolas Pitre + * Copyright: MontaVista Software Inc. + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ + +#ifndef __PXA2XX_REGS_H +#define __PXA2XX_REGS_H + +/* + * Memory controller + */ + +#define MDCNFG __REG(0x48000000) /* SDRAM Configuration Register 0 */ +#define MDREFR __REG(0x48000004) /* SDRAM Refresh Control Register */ +#define MSC0 __REG(0x48000008) /* Static Memory Control Register 0 */ +#define MSC1 __REG(0x4800000C) /* Static Memory Control Register 1 */ +#define MSC2 __REG(0x48000010) /* Static Memory Control Register 2 */ +#define MECR __REG(0x48000014) /* Expansion Memory (PCMCIA/Compact Flash) Bus Configuration */ +#define SXLCR __REG(0x48000018) /* LCR value to be written to SDRAM-Timing Synchronous Flash */ +#define SXCNFG __REG(0x4800001C) /* Synchronous Static Memory Control Register */ +#define SXMRS __REG(0x48000024) /* MRS value to be written to Synchronous Flash or SMROM */ +#define MCMEM0 __REG(0x48000028) /* Card interface Common Memory Space Socket 0 Timing */ +#define MCMEM1 __REG(0x4800002C) /* Card interface Common Memory Space Socket 1 Timing */ +#define MCATT0 __REG(0x48000030) /* Card interface Attribute Space Socket 0 Timing Configuration */ +#define MCATT1 __REG(0x48000034) /* Card interface Attribute Space Socket 1 Timing Configuration */ +#define MCIO0 __REG(0x48000038) /* Card interface I/O Space Socket 0 Timing Configuration */ +#define MCIO1 __REG(0x4800003C) /* Card interface I/O Space Socket 1 Timing Configuration */ +#define MDMRS __REG(0x48000040) /* MRS value to be written to SDRAM */ +#define BOOT_DEF __REG(0x48000044) /* Read-Only Boot-Time Register. Contains BOOT_SEL and PKG_SEL */ + +/* + * More handy macros for PCMCIA + * + * Arg is socket number + */ +#define MCMEM(s) __REG2(0x48000028, (s)<<2 ) /* Card interface Common Memory Space Socket s Timing */ +#define MCATT(s) __REG2(0x48000030, (s)<<2 ) /* Card interface Attribute Space Socket s Timing Configuration */ +#define MCIO(s) __REG2(0x48000038, (s)<<2 ) /* Card interface I/O Space Socket s Timing Configuration */ + +/* MECR register defines */ +#define MECR_NOS (1 << 0) /* Number Of Sockets: 0 -> 1 sock, 1 -> 2 sock */ +#define MECR_CIT (1 << 1) /* Card Is There: 0 -> no card, 1 -> card inserted */ + +#define MDREFR_K0DB4 (1 << 29) /* SDCLK0 Divide by 4 Control/Status */ +#define MDREFR_K2FREE (1 << 25) /* SDRAM Free-Running Control */ +#define MDREFR_K1FREE (1 << 24) /* SDRAM Free-Running Control */ +#define MDREFR_K0FREE (1 << 23) /* SDRAM Free-Running Control */ +#define MDREFR_SLFRSH (1 << 22) /* SDRAM Self-Refresh Control/Status */ +#define MDREFR_APD (1 << 20) /* SDRAM/SSRAM Auto-Power-Down Enable */ +#define MDREFR_K2DB2 (1 << 19) /* SDCLK2 Divide by 2 Control/Status */ +#define MDREFR_K2RUN (1 << 18) /* SDCLK2 Run Control/Status */ +#define MDREFR_K1DB2 (1 << 17) /* SDCLK1 Divide by 2 Control/Status */ +#define MDREFR_K1RUN (1 << 16) /* SDCLK1 Run Control/Status */ +#define MDREFR_E1PIN (1 << 15) /* SDCKE1 Level Control/Status */ +#define MDREFR_K0DB2 (1 << 14) /* SDCLK0 Divide by 2 Control/Status */ +#define MDREFR_K0RUN (1 << 13) /* SDCLK0 Run Control/Status */ +#define MDREFR_E0PIN (1 << 12) /* SDCKE0 Level Control/Status */ + + +#ifdef CONFIG_PXA27x + +#define ARB_CNTRL __REG(0x48000048) /* Arbiter Control Register */ + +#define ARB_DMA_SLV_PARK (1<<31) /* Be parked with DMA slave when idle */ +#define ARB_CI_PARK (1<<30) /* Be parked with Camera Interface when idle */ +#define ARB_EX_MEM_PARK (1<<29) /* Be parked with external MEMC when idle */ +#define ARB_INT_MEM_PARK (1<<28) /* Be parked with internal MEMC when idle */ +#define ARB_USB_PARK (1<<27) /* Be parked with USB when idle */ +#define ARB_LCD_PARK (1<<26) /* Be parked with LCD when idle */ +#define ARB_DMA_PARK (1<<25) /* Be parked with DMA when idle */ +#define ARB_CORE_PARK (1<<24) /* Be parked with core when idle */ +#define ARB_LOCK_FLAG (1<<23) /* Only Locking masters gain access to the bus */ + +#endif + + +/* + * Power Manager + */ + +#define PMCR __REG(0x40F00000) /* Power Manager Control Register */ +#define PSSR __REG(0x40F00004) /* Power Manager Sleep Status Register */ +#define PSPR __REG(0x40F00008) /* Power Manager Scratch Pad Register */ +#define PWER __REG(0x40F0000C) /* Power Manager Wake-up Enable Register */ +#define PRER __REG(0x40F00010) /* Power Manager GPIO Rising-Edge Detect Enable Register */ +#define PFER __REG(0x40F00014) /* Power Manager GPIO Falling-Edge Detect Enable Register */ +#define PEDR __REG(0x40F00018) /* Power Manager GPIO Edge Detect Status Register */ +#define PCFR __REG(0x40F0001C) /* Power Manager General Configuration Register */ +#define PGSR0 __REG(0x40F00020) /* Power Manager GPIO Sleep State Register for GP[31-0] */ +#define PGSR1 __REG(0x40F00024) /* Power Manager GPIO Sleep State Register for GP[63-32] */ +#define PGSR2 __REG(0x40F00028) /* Power Manager GPIO Sleep State Register for GP[84-64] */ +#define PGSR3 __REG(0x40F0002C) /* Power Manager GPIO Sleep State Register for GP[118-96] */ +#define RCSR __REG(0x40F00030) /* Reset Controller Status Register */ + +#define PSLR __REG(0x40F00034) /* Power Manager Sleep Config Register */ +#define PSTR __REG(0x40F00038) /* Power Manager Standby Config Register */ +#define PSNR __REG(0x40F0003C) /* Power Manager Sense Config Register */ +#define PVCR __REG(0x40F00040) /* Power Manager VoltageControl Register */ +#define PKWR __REG(0x40F00050) /* Power Manager KB Wake-up Enable Reg */ +#define PKSR __REG(0x40F00054) /* Power Manager KB Level-Detect Register */ +#define PCMD(x) __REG2(0x40F00080, (x)<<2) +#define PCMD0 __REG(0x40F00080 + 0 * 4) +#define PCMD1 __REG(0x40F00080 + 1 * 4) +#define PCMD2 __REG(0x40F00080 + 2 * 4) +#define PCMD3 __REG(0x40F00080 + 3 * 4) +#define PCMD4 __REG(0x40F00080 + 4 * 4) +#define PCMD5 __REG(0x40F00080 + 5 * 4) +#define PCMD6 __REG(0x40F00080 + 6 * 4) +#define PCMD7 __REG(0x40F00080 + 7 * 4) +#define PCMD8 __REG(0x40F00080 + 8 * 4) +#define PCMD9 __REG(0x40F00080 + 9 * 4) +#define PCMD10 __REG(0x40F00080 + 10 * 4) +#define PCMD11 __REG(0x40F00080 + 11 * 4) +#define PCMD12 __REG(0x40F00080 + 12 * 4) +#define PCMD13 __REG(0x40F00080 + 13 * 4) +#define PCMD14 __REG(0x40F00080 + 14 * 4) +#define PCMD15 __REG(0x40F00080 + 15 * 4) +#define PCMD16 __REG(0x40F00080 + 16 * 4) +#define PCMD17 __REG(0x40F00080 + 17 * 4) +#define PCMD18 __REG(0x40F00080 + 18 * 4) +#define PCMD19 __REG(0x40F00080 + 19 * 4) +#define PCMD20 __REG(0x40F00080 + 20 * 4) +#define PCMD21 __REG(0x40F00080 + 21 * 4) +#define PCMD22 __REG(0x40F00080 + 22 * 4) +#define PCMD23 __REG(0x40F00080 + 23 * 4) +#define PCMD24 __REG(0x40F00080 + 24 * 4) +#define PCMD25 __REG(0x40F00080 + 25 * 4) +#define PCMD26 __REG(0x40F00080 + 26 * 4) +#define PCMD27 __REG(0x40F00080 + 27 * 4) +#define PCMD28 __REG(0x40F00080 + 28 * 4) +#define PCMD29 __REG(0x40F00080 + 29 * 4) +#define PCMD30 __REG(0x40F00080 + 30 * 4) +#define PCMD31 __REG(0x40F00080 + 31 * 4) + +#define PCMD_MBC (1<<12) +#define PCMD_DCE (1<<11) +#define PCMD_LC (1<<10) +/* FIXME: PCMD_SQC need be checked. */ +#define PCMD_SQC (3<<8) /* currently only bit 8 is changeable, + bit 9 should be 0 all day. */ +#define PVCR_VCSA (0x1<<14) +#define PVCR_CommandDelay (0xf80) +#define PCFR_PI2C_EN (0x1 << 6) + +#define PSSR_OTGPH (1 << 6) /* OTG Peripheral control Hold */ +#define PSSR_RDH (1 << 5) /* Read Disable Hold */ +#define PSSR_PH (1 << 4) /* Peripheral Control Hold */ +#define PSSR_STS (1 << 3) /* Standby Mode Status */ +#define PSSR_VFS (1 << 2) /* VDD Fault Status */ +#define PSSR_BFS (1 << 1) /* Battery Fault Status */ +#define PSSR_SSS (1 << 0) /* Software Sleep Status */ + +#define PSLR_SL_ROD (1 << 20) /* Sleep-Mode/Depp-Sleep Mode nRESET_OUT Disable */ + +#define PCFR_RO (1 << 15) /* RDH Override */ +#define PCFR_PO (1 << 14) /* PH Override */ +#define PCFR_GPROD (1 << 12) /* GPIO nRESET_OUT Disable */ +#define PCFR_L1_EN (1 << 11) /* Sleep Mode L1 converter Enable */ +#define PCFR_FVC (1 << 10) /* Frequency/Voltage Change */ +#define PCFR_DC_EN (1 << 7) /* Sleep/deep-sleep DC-DC Converter Enable */ +#define PCFR_PI2CEN (1 << 6) /* Enable PI2C controller */ +#define PCFR_GPR_EN (1 << 4) /* nRESET_GPIO Pin Enable */ +#define PCFR_DS (1 << 3) /* Deep Sleep Mode */ +#define PCFR_FS (1 << 2) /* Float Static Chip Selects */ +#define PCFR_FP (1 << 1) /* Float PCMCIA controls */ +#define PCFR_OPDE (1 << 0) /* 3.6864 MHz oscillator power-down enable */ + +#define RCSR_GPR (1 << 3) /* GPIO Reset */ +#define RCSR_SMR (1 << 2) /* Sleep Mode */ +#define RCSR_WDR (1 << 1) /* Watchdog Reset */ +#define RCSR_HWR (1 << 0) /* Hardware Reset */ + +#define PWER_GPIO(Nb) (1 << Nb) /* GPIO [0..15] wake-up enable */ +#define PWER_GPIO0 PWER_GPIO (0) /* GPIO [0] wake-up enable */ +#define PWER_GPIO1 PWER_GPIO (1) /* GPIO [1] wake-up enable */ +#define PWER_GPIO2 PWER_GPIO (2) /* GPIO [2] wake-up enable */ +#define PWER_GPIO3 PWER_GPIO (3) /* GPIO [3] wake-up enable */ +#define PWER_GPIO4 PWER_GPIO (4) /* GPIO [4] wake-up enable */ +#define PWER_GPIO5 PWER_GPIO (5) /* GPIO [5] wake-up enable */ +#define PWER_GPIO6 PWER_GPIO (6) /* GPIO [6] wake-up enable */ +#define PWER_GPIO7 PWER_GPIO (7) /* GPIO [7] wake-up enable */ +#define PWER_GPIO8 PWER_GPIO (8) /* GPIO [8] wake-up enable */ +#define PWER_GPIO9 PWER_GPIO (9) /* GPIO [9] wake-up enable */ +#define PWER_GPIO10 PWER_GPIO (10) /* GPIO [10] wake-up enable */ +#define PWER_GPIO11 PWER_GPIO (11) /* GPIO [11] wake-up enable */ +#define PWER_GPIO12 PWER_GPIO (12) /* GPIO [12] wake-up enable */ +#define PWER_GPIO13 PWER_GPIO (13) /* GPIO [13] wake-up enable */ +#define PWER_GPIO14 PWER_GPIO (14) /* GPIO [14] wake-up enable */ +#define PWER_GPIO15 PWER_GPIO (15) /* GPIO [15] wake-up enable */ +#define PWER_RTC 0x80000000 /* RTC alarm wake-up enable */ + +/* + * PXA2xx specific Core clock definitions + */ +#define CCCR __REG(0x41300000) /* Core Clock Configuration Register */ +#define CCSR __REG(0x4130000C) /* Core Clock Status Register */ +#define CKEN __REG(0x41300004) /* Clock Enable Register */ +#define OSCC __REG(0x41300008) /* Oscillator Configuration Register */ + +#define CCCR_N_MASK 0x0380 /* Run Mode Frequency to Turbo Mode Frequency Multiplier */ +#define CCCR_M_MASK 0x0060 /* Memory Frequency to Run Mode Frequency Multiplier */ +#define CCCR_L_MASK 0x001f /* Crystal Frequency to Memory Frequency Multiplier */ + +#define CKEN_AC97CONF (31) /* AC97 Controller Configuration */ +#define CKEN_CAMERA (24) /* Camera Interface Clock Enable */ +#define CKEN_SSP1 (23) /* SSP1 Unit Clock Enable */ +#define CKEN_MEMC (22) /* Memory Controller Clock Enable */ +#define CKEN_MEMSTK (21) /* Memory Stick Host Controller */ +#define CKEN_IM (20) /* Internal Memory Clock Enable */ +#define CKEN_KEYPAD (19) /* Keypad Interface Clock Enable */ +#define CKEN_USIM (18) /* USIM Unit Clock Enable */ +#define CKEN_MSL (17) /* MSL Unit Clock Enable */ +#define CKEN_LCD (16) /* LCD Unit Clock Enable */ +#define CKEN_PWRI2C (15) /* PWR I2C Unit Clock Enable */ +#define CKEN_I2C (14) /* I2C Unit Clock Enable */ +#define CKEN_FICP (13) /* FICP Unit Clock Enable */ +#define CKEN_MMC (12) /* MMC Unit Clock Enable */ +#define CKEN_USB (11) /* USB Unit Clock Enable */ +#define CKEN_ASSP (10) /* ASSP (SSP3) Clock Enable */ +#define CKEN_USBHOST (10) /* USB Host Unit Clock Enable */ +#define CKEN_OSTIMER (9) /* OS Timer Unit Clock Enable */ +#define CKEN_NSSP (9) /* NSSP (SSP2) Clock Enable */ +#define CKEN_I2S (8) /* I2S Unit Clock Enable */ +#define CKEN_BTUART (7) /* BTUART Unit Clock Enable */ +#define CKEN_FFUART (6) /* FFUART Unit Clock Enable */ +#define CKEN_STUART (5) /* STUART Unit Clock Enable */ +#define CKEN_HWUART (4) /* HWUART Unit Clock Enable */ +#define CKEN_SSP3 (4) /* SSP3 Unit Clock Enable */ +#define CKEN_SSP (3) /* SSP Unit Clock Enable */ +#define CKEN_SSP2 (3) /* SSP2 Unit Clock Enable */ +#define CKEN_AC97 (2) /* AC97 Unit Clock Enable */ +#define CKEN_PWM1 (1) /* PWM1 Clock Enable */ +#define CKEN_PWM0 (0) /* PWM0 Clock Enable */ + +#define OSCC_OON (1 << 1) /* 32.768kHz OON (write-once only bit) */ +#define OSCC_OOK (1 << 0) /* 32.768kHz OOK (read-only bit) */ + +#endif diff --git a/arch/arm/mach-pxa/include/mach/pxa2xx_spi.h b/arch/arm/mach-pxa/include/mach/pxa2xx_spi.h new file mode 100644 index 00000000000..2206cb61a9f --- /dev/null +++ b/arch/arm/mach-pxa/include/mach/pxa2xx_spi.h @@ -0,0 +1,46 @@ +/* + * Copyright (C) 2005 Stephen Street / StreetFire Sound Labs + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA. + */ + +#ifndef PXA2XX_SPI_H_ +#define PXA2XX_SPI_H_ + +#define PXA2XX_CS_ASSERT (0x01) +#define PXA2XX_CS_DEASSERT (0x02) + +/* device.platform_data for SSP controller devices */ +struct pxa2xx_spi_master { + u32 clock_enable; + u16 num_chipselect; + u8 enable_dma; +}; + +/* spi_board_info.controller_data for SPI slave devices, + * copied to spi_device.platform_data ... mostly for dma tuning + */ +struct pxa2xx_spi_chip { + u8 tx_threshold; + u8 rx_threshold; + u8 dma_burst_size; + u32 timeout; + u8 enable_loopback; + void (*cs_control)(u32 command); +}; + +extern void pxa2xx_set_spi_info(unsigned id, struct pxa2xx_spi_master *info); + +#endif /*PXA2XX_SPI_H_*/ diff --git a/arch/arm/mach-pxa/include/mach/pxa3xx-regs.h b/arch/arm/mach-pxa/include/mach/pxa3xx-regs.h new file mode 100644 index 00000000000..b1fcd10ab6c --- /dev/null +++ b/arch/arm/mach-pxa/include/mach/pxa3xx-regs.h @@ -0,0 +1,205 @@ +/* + * arch/arm/mach-pxa/include/mach/pxa3xx-regs.h + * + * PXA3xx specific register definitions + * + * Copyright (C) 2007 Marvell International Ltd. + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ + +#ifndef __ASM_ARCH_PXA3XX_REGS_H +#define __ASM_ARCH_PXA3XX_REGS_H + +/* + * Oscillator Configuration Register (OSCC) + */ +#define OSCC __REG(0x41350000) /* Oscillator Configuration Register */ + +#define OSCC_PEN (1 << 11) /* 13MHz POUT */ + + +/* + * Service Power Management Unit (MPMU) + */ +#define PMCR __REG(0x40F50000) /* Power Manager Control Register */ +#define PSR __REG(0x40F50004) /* Power Manager S2 Status Register */ +#define PSPR __REG(0x40F50008) /* Power Manager Scratch Pad Register */ +#define PCFR __REG(0x40F5000C) /* Power Manager General Configuration Register */ +#define PWER __REG(0x40F50010) /* Power Manager Wake-up Enable Register */ +#define PWSR __REG(0x40F50014) /* Power Manager Wake-up Status Register */ +#define PECR __REG(0x40F50018) /* Power Manager EXT_WAKEUP[1:0] Control Register */ +#define DCDCSR __REG(0x40F50080) /* DC-DC Controller Status Register */ +#define PVCR __REG(0x40F50100) /* Power Manager Voltage Change Control Register */ +#define PCMD(x) __REG(0x40F50110 + ((x) << 2)) + +/* + * Slave Power Managment Unit + */ +#define ASCR __REG(0x40f40000) /* Application Subsystem Power Status/Configuration */ +#define ARSR __REG(0x40f40004) /* Application Subsystem Reset Status */ +#define AD3ER __REG(0x40f40008) /* Application Subsystem Wake-Up from D3 Enable */ +#define AD3SR __REG(0x40f4000c) /* Application Subsystem Wake-Up from D3 Status */ +#define AD2D0ER __REG(0x40f40010) /* Application Subsystem Wake-Up from D2 to D0 Enable */ +#define AD2D0SR __REG(0x40f40014) /* Application Subsystem Wake-Up from D2 to D0 Status */ +#define AD2D1ER __REG(0x40f40018) /* Application Subsystem Wake-Up from D2 to D1 Enable */ +#define AD2D1SR __REG(0x40f4001c) /* Application Subsystem Wake-Up from D2 to D1 Status */ +#define AD1D0ER __REG(0x40f40020) /* Application Subsystem Wake-Up from D1 to D0 Enable */ +#define AD1D0SR __REG(0x40f40024) /* Application Subsystem Wake-Up from D1 to D0 Status */ +#define AGENP __REG(0x40f4002c) /* Application Subsystem General Purpose */ +#define AD3R __REG(0x40f40030) /* Application Subsystem D3 Configuration */ +#define AD2R __REG(0x40f40034) /* Application Subsystem D2 Configuration */ +#define AD1R __REG(0x40f40038) /* Application Subsystem D1 Configuration */ + +/* + * Application Subsystem Configuration bits. + */ +#define ASCR_RDH (1 << 31) +#define ASCR_D1S (1 << 2) +#define ASCR_D2S (1 << 1) +#define ASCR_D3S (1 << 0) + +/* + * Application Reset Status bits. + */ +#define ARSR_GPR (1 << 3) +#define ARSR_LPMR (1 << 2) +#define ARSR_WDT (1 << 1) +#define ARSR_HWR (1 << 0) + +/* + * Application Subsystem Wake-Up bits. + */ +#define ADXER_WRTC (1 << 31) /* RTC */ +#define ADXER_WOST (1 << 30) /* OS Timer */ +#define ADXER_WTSI (1 << 29) /* Touchscreen */ +#define ADXER_WUSBH (1 << 28) /* USB host */ +#define ADXER_WUSB2 (1 << 26) /* USB client 2.0 */ +#define ADXER_WMSL0 (1 << 24) /* MSL port 0*/ +#define ADXER_WDMUX3 (1 << 23) /* USB EDMUX3 */ +#define ADXER_WDMUX2 (1 << 22) /* USB EDMUX2 */ +#define ADXER_WKP (1 << 21) /* Keypad */ +#define ADXER_WUSIM1 (1 << 20) /* USIM Port 1 */ +#define ADXER_WUSIM0 (1 << 19) /* USIM Port 0 */ +#define ADXER_WOTG (1 << 16) /* USBOTG input */ +#define ADXER_MFP_WFLASH (1 << 15) /* MFP: Data flash busy */ +#define ADXER_MFP_GEN12 (1 << 14) /* MFP: MMC3/GPIO/OST inputs */ +#define ADXER_MFP_WMMC2 (1 << 13) /* MFP: MMC2 */ +#define ADXER_MFP_WMMC1 (1 << 12) /* MFP: MMC1 */ +#define ADXER_MFP_WI2C (1 << 11) /* MFP: I2C */ +#define ADXER_MFP_WSSP4 (1 << 10) /* MFP: SSP4 */ +#define ADXER_MFP_WSSP3 (1 << 9) /* MFP: SSP3 */ +#define ADXER_MFP_WMAXTRIX (1 << 8) /* MFP: matrix keypad */ +#define ADXER_MFP_WUART3 (1 << 7) /* MFP: UART3 */ +#define ADXER_MFP_WUART2 (1 << 6) /* MFP: UART2 */ +#define ADXER_MFP_WUART1 (1 << 5) /* MFP: UART1 */ +#define ADXER_MFP_WSSP2 (1 << 4) /* MFP: SSP2 */ +#define ADXER_MFP_WSSP1 (1 << 3) /* MFP: SSP1 */ +#define ADXER_MFP_WAC97 (1 << 2) /* MFP: AC97 */ +#define ADXER_WEXTWAKE1 (1 << 1) /* External Wake 1 */ +#define ADXER_WEXTWAKE0 (1 << 0) /* External Wake 0 */ + +/* + * AD3R/AD2R/AD1R bits. R2-R5 are only defined for PXA320. + */ +#define ADXR_L2 (1 << 8) +#define ADXR_R5 (1 << 5) +#define ADXR_R4 (1 << 4) +#define ADXR_R3 (1 << 3) +#define ADXR_R2 (1 << 2) +#define ADXR_R1 (1 << 1) +#define ADXR_R0 (1 << 0) + +/* + * Values for PWRMODE CP15 register + */ +#define PXA3xx_PM_S3D4C4 0x07 /* aka deep sleep */ +#define PXA3xx_PM_S2D3C4 0x06 /* aka sleep */ +#define PXA3xx_PM_S0D2C2 0x03 /* aka standby */ +#define PXA3xx_PM_S0D1C2 0x02 /* aka LCD refresh */ +#define PXA3xx_PM_S0D0C1 0x01 + +/* + * Application Subsystem Clock + */ +#define ACCR __REG(0x41340000) /* Application Subsystem Clock Configuration Register */ +#define ACSR __REG(0x41340004) /* Application Subsystem Clock Status Register */ +#define AICSR __REG(0x41340008) /* Application Subsystem Interrupt Control/Status Register */ +#define CKENA __REG(0x4134000C) /* A Clock Enable Register */ +#define CKENB __REG(0x41340010) /* B Clock Enable Register */ +#define AC97_DIV __REG(0x41340014) /* AC97 clock divisor value register */ + +#define ACCR_XPDIS (1 << 31) /* Core PLL Output Disable */ +#define ACCR_SPDIS (1 << 30) /* System PLL Output Disable */ +#define ACCR_D0CS (1 << 26) /* D0 Mode Clock Select */ +#define ACCR_PCCE (1 << 11) /* Power Mode Change Clock Enable */ +#define ACCR_DDR_D0CS (1 << 7) /* DDR SDRAM clock frequency in D0CS (PXA31x only) */ + +#define ACCR_SMCFS_MASK (0x7 << 23) /* Static Memory Controller Frequency Select */ +#define ACCR_SFLFS_MASK (0x3 << 18) /* Frequency Select for Internal Memory Controller */ +#define ACCR_XSPCLK_MASK (0x3 << 16) /* Core Frequency during Frequency Change */ +#define ACCR_HSS_MASK (0x3 << 14) /* System Bus-Clock Frequency Select */ +#define ACCR_DMCFS_MASK (0x3 << 12) /* Dynamic Memory Controller Clock Frequency Select */ +#define ACCR_XN_MASK (0x7 << 8) /* Core PLL Turbo-Mode-to-Run-Mode Ratio */ +#define ACCR_XL_MASK (0x1f) /* Core PLL Run-Mode-to-Oscillator Ratio */ + +#define ACCR_SMCFS(x) (((x) & 0x7) << 23) +#define ACCR_SFLFS(x) (((x) & 0x3) << 18) +#define ACCR_XSPCLK(x) (((x) & 0x3) << 16) +#define ACCR_HSS(x) (((x) & 0x3) << 14) +#define ACCR_DMCFS(x) (((x) & 0x3) << 12) +#define ACCR_XN(x) (((x) & 0x7) << 8) +#define ACCR_XL(x) ((x) & 0x1f) + +/* + * Clock Enable Bit + */ +#define CKEN_LCD 1 /* < LCD Clock Enable */ +#define CKEN_USBH 2 /* < USB host clock enable */ +#define CKEN_CAMERA 3 /* < Camera interface clock enable */ +#define CKEN_NAND 4 /* < NAND Flash Controller Clock Enable */ +#define CKEN_USB2 6 /* < USB 2.0 client clock enable. */ +#define CKEN_DMC 8 /* < Dynamic Memory Controller clock enable */ +#define CKEN_SMC 9 /* < Static Memory Controller clock enable */ +#define CKEN_ISC 10 /* < Internal SRAM Controller clock enable */ +#define CKEN_BOOT 11 /* < Boot rom clock enable */ +#define CKEN_MMC1 12 /* < MMC1 Clock enable */ +#define CKEN_MMC2 13 /* < MMC2 clock enable */ +#define CKEN_KEYPAD 14 /* < Keypand Controller Clock Enable */ +#define CKEN_CIR 15 /* < Consumer IR Clock Enable */ +#define CKEN_USIM0 17 /* < USIM[0] Clock Enable */ +#define CKEN_USIM1 18 /* < USIM[1] Clock Enable */ +#define CKEN_TPM 19 /* < TPM clock enable */ +#define CKEN_UDC 20 /* < UDC clock enable */ +#define CKEN_BTUART 21 /* < BTUART clock enable */ +#define CKEN_FFUART 22 /* < FFUART clock enable */ +#define CKEN_STUART 23 /* < STUART clock enable */ +#define CKEN_AC97 24 /* < AC97 clock enable */ +#define CKEN_TOUCH 25 /* < Touch screen Interface Clock Enable */ +#define CKEN_SSP1 26 /* < SSP1 clock enable */ +#define CKEN_SSP2 27 /* < SSP2 clock enable */ +#define CKEN_SSP3 28 /* < SSP3 clock enable */ +#define CKEN_SSP4 29 /* < SSP4 clock enable */ +#define CKEN_MSL0 30 /* < MSL0 clock enable */ +#define CKEN_PWM0 32 /* < PWM[0] clock enable */ +#define CKEN_PWM1 33 /* < PWM[1] clock enable */ +#define CKEN_I2C 36 /* < I2C clock enable */ +#define CKEN_INTC 38 /* < Interrupt controller clock enable */ +#define CKEN_GPIO 39 /* < GPIO clock enable */ +#define CKEN_1WIRE 40 /* < 1-wire clock enable */ +#define CKEN_HSIO2 41 /* < HSIO2 clock enable */ +#define CKEN_MINI_IM 48 /* < Mini-IM */ +#define CKEN_MINI_LCD 49 /* < Mini LCD */ + +#if defined(CONFIG_CPU_PXA310) +#define CKEN_MMC3 5 /* < MMC3 Clock Enable */ +#define CKEN_MVED 43 /* < MVED clock enable */ +#endif + +/* Note: GCU clock enable bit differs on PXA300/PXA310 and PXA320 */ +#define PXA300_CKEN_GRAPHICS 42 /* Graphics controller clock enable */ +#define PXA320_CKEN_GRAPHICS 7 /* Graphics controller clock enable */ + +#endif /* __ASM_ARCH_PXA3XX_REGS_H */ diff --git a/arch/arm/mach-pxa/include/mach/pxa3xx_nand.h b/arch/arm/mach-pxa/include/mach/pxa3xx_nand.h new file mode 100644 index 00000000000..eb4b190b665 --- /dev/null +++ b/arch/arm/mach-pxa/include/mach/pxa3xx_nand.h @@ -0,0 +1,20 @@ +#ifndef __ASM_ARCH_PXA3XX_NAND_H +#define __ASM_ARCH_PXA3XX_NAND_H + +#include <linux/mtd/mtd.h> +#include <linux/mtd/partitions.h> + +struct pxa3xx_nand_platform_data { + + /* the data flash bus is shared between the Static Memory + * Controller and the Data Flash Controller, the arbiter + * controls the ownership of the bus + */ + int enable_arbiter; + + struct mtd_partition *parts; + unsigned int nr_parts; +}; + +extern void pxa3xx_set_nand_info(struct pxa3xx_nand_platform_data *info); +#endif /* __ASM_ARCH_PXA3XX_NAND_H */ diff --git a/arch/arm/mach-pxa/include/mach/pxafb.h b/arch/arm/mach-pxa/include/mach/pxafb.h new file mode 100644 index 00000000000..8e591118371 --- /dev/null +++ b/arch/arm/mach-pxa/include/mach/pxafb.h @@ -0,0 +1,153 @@ +/* + * arch/arm/mach-pxa/include/mach/pxafb.h + * + * Support for the xscale frame buffer. + * + * Author: Jean-Frederic Clere + * Created: Sep 22, 2003 + * Copyright: jfclere@sinix.net + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ + +#include <linux/fb.h> +#include <mach/regs-lcd.h> + +/* + * Supported LCD connections + * + * bits 0 - 3: for LCD panel type: + * + * STN - for passive matrix + * DSTN - for dual scan passive matrix + * TFT - for active matrix + * + * bits 4 - 9 : for bus width + * bits 10-17 : for AC Bias Pin Frequency + * bit 18 : for output enable polarity + * bit 19 : for pixel clock edge + * bit 20 : for output pixel format when base is RGBT16 + */ +#define LCD_CONN_TYPE(_x) ((_x) & 0x0f) +#define LCD_CONN_WIDTH(_x) (((_x) >> 4) & 0x1f) + +#define LCD_TYPE_UNKNOWN 0 +#define LCD_TYPE_MONO_STN 1 +#define LCD_TYPE_MONO_DSTN 2 +#define LCD_TYPE_COLOR_STN 3 +#define LCD_TYPE_COLOR_DSTN 4 +#define LCD_TYPE_COLOR_TFT 5 +#define LCD_TYPE_SMART_PANEL 6 +#define LCD_TYPE_MAX 7 + +#define LCD_MONO_STN_4BPP ((4 << 4) | LCD_TYPE_MONO_STN) +#define LCD_MONO_STN_8BPP ((8 << 4) | LCD_TYPE_MONO_STN) +#define LCD_MONO_DSTN_8BPP ((8 << 4) | LCD_TYPE_MONO_DSTN) +#define LCD_COLOR_STN_8BPP ((8 << 4) | LCD_TYPE_COLOR_STN) +#define LCD_COLOR_DSTN_16BPP ((16 << 4) | LCD_TYPE_COLOR_DSTN) +#define LCD_COLOR_TFT_16BPP ((16 << 4) | LCD_TYPE_COLOR_TFT) +#define LCD_COLOR_TFT_18BPP ((18 << 4) | LCD_TYPE_COLOR_TFT) +#define LCD_SMART_PANEL_8BPP ((8 << 4) | LCD_TYPE_SMART_PANEL) +#define LCD_SMART_PANEL_16BPP ((16 << 4) | LCD_TYPE_SMART_PANEL) +#define LCD_SMART_PANEL_18BPP ((18 << 4) | LCD_TYPE_SMART_PANEL) + +#define LCD_AC_BIAS_FREQ(x) (((x) & 0xff) << 10) +#define LCD_BIAS_ACTIVE_HIGH (0 << 18) +#define LCD_BIAS_ACTIVE_LOW (1 << 18) +#define LCD_PCLK_EDGE_RISE (0 << 19) +#define LCD_PCLK_EDGE_FALL (1 << 19) +#define LCD_ALTERNATE_MAPPING (1 << 20) + +/* + * This structure describes the machine which we are running on. + * It is set in linux/arch/arm/mach-pxa/machine_name.c and used in the probe routine + * of linux/drivers/video/pxafb.c + */ +struct pxafb_mode_info { + u_long pixclock; + + u_short xres; + u_short yres; + + u_char bpp; + u_int cmap_greyscale:1, + depth:8, + unused:23; + + /* Parallel Mode Timing */ + u_char hsync_len; + u_char left_margin; + u_char right_margin; + + u_char vsync_len; + u_char upper_margin; + u_char lower_margin; + u_char sync; + + /* Smart Panel Mode Timing - see PXA27x DM 7.4.15.0.3 for details + * Note: + * 1. all parameters in nanosecond (ns) + * 2. a0cs{rd,wr}_set_hld are controlled by the same register bits + * in pxa27x and pxa3xx, initialize them to the same value or + * the larger one will be used + * 3. same to {rd,wr}_pulse_width + */ + unsigned a0csrd_set_hld; /* A0 and CS Setup/Hold Time before/after L_FCLK_RD */ + unsigned a0cswr_set_hld; /* A0 and CS Setup/Hold Time before/after L_PCLK_WR */ + unsigned wr_pulse_width; /* L_PCLK_WR pulse width */ + unsigned rd_pulse_width; /* L_FCLK_RD pulse width */ + unsigned cmd_inh_time; /* Command Inhibit time between two writes */ + unsigned op_hold_time; /* Output Hold time from L_FCLK_RD negation */ +}; + +struct pxafb_mach_info { + struct pxafb_mode_info *modes; + unsigned int num_modes; + + unsigned int lcd_conn; + + u_int fixed_modes:1, + cmap_inverse:1, + cmap_static:1, + unused:29; + + /* The following should be defined in LCCR0 + * LCCR0_Act or LCCR0_Pas Active or Passive + * LCCR0_Sngl or LCCR0_Dual Single/Dual panel + * LCCR0_Mono or LCCR0_Color Mono/Color + * LCCR0_4PixMono or LCCR0_8PixMono (in mono single mode) + * LCCR0_DMADel(Tcpu) (optional) DMA request delay + * + * The following should not be defined in LCCR0: + * LCCR0_OUM, LCCR0_BM, LCCR0_QDM, LCCR0_DIS, LCCR0_EFM + * LCCR0_IUM, LCCR0_SFM, LCCR0_LDM, LCCR0_ENB + */ + u_int lccr0; + /* The following should be defined in LCCR3 + * LCCR3_OutEnH or LCCR3_OutEnL Output enable polarity + * LCCR3_PixRsEdg or LCCR3_PixFlEdg Pixel clock edge type + * LCCR3_Acb(X) AB Bias pin frequency + * LCCR3_DPC (optional) Double Pixel Clock mode (untested) + * + * The following should not be defined in LCCR3 + * LCCR3_HSP, LCCR3_VSP, LCCR0_Pcd(x), LCCR3_Bpp + */ + u_int lccr3; + /* The following should be defined in LCCR4 + * LCCR4_PAL_FOR_0 or LCCR4_PAL_FOR_1 or LCCR4_PAL_FOR_2 + * + * All other bits in LCCR4 should be left alone. + */ + u_int lccr4; + void (*pxafb_backlight_power)(int); + void (*pxafb_lcd_power)(int, struct fb_var_screeninfo *); + void (*smart_update)(struct fb_info *); +}; +void set_pxa_fb_info(struct pxafb_mach_info *hard_pxa_fb_info); +void set_pxa_fb_parent(struct device *parent_dev); +unsigned long pxafb_get_hsync_time(struct device *dev); + +extern int pxafb_smart_queue(struct fb_info *info, uint16_t *cmds, int); +extern int pxafb_smart_flush(struct fb_info *info); diff --git a/arch/arm/mach-pxa/include/mach/regs-lcd.h b/arch/arm/mach-pxa/include/mach/regs-lcd.h new file mode 100644 index 00000000000..c689c4ea769 --- /dev/null +++ b/arch/arm/mach-pxa/include/mach/regs-lcd.h @@ -0,0 +1,180 @@ +#ifndef __ASM_ARCH_REGS_LCD_H +#define __ASM_ARCH_REGS_LCD_H + +#include <mach/bitfield.h> + +/* + * LCD Controller Registers and Bits Definitions + */ +#define LCCR0 (0x000) /* LCD Controller Control Register 0 */ +#define LCCR1 (0x004) /* LCD Controller Control Register 1 */ +#define LCCR2 (0x008) /* LCD Controller Control Register 2 */ +#define LCCR3 (0x00C) /* LCD Controller Control Register 3 */ +#define LCCR4 (0x010) /* LCD Controller Control Register 4 */ +#define LCCR5 (0x014) /* LCD Controller Control Register 5 */ +#define DFBR0 (0x020) /* DMA Channel 0 Frame Branch Register */ +#define DFBR1 (0x024) /* DMA Channel 1 Frame Branch Register */ +#define LCSR (0x038) /* LCD Controller Status Register */ +#define LIIDR (0x03C) /* LCD Controller Interrupt ID Register */ +#define TMEDRGBR (0x040) /* TMED RGB Seed Register */ +#define TMEDCR (0x044) /* TMED Control Register */ + +#define CMDCR (0x100) /* Command Control Register */ +#define PRSR (0x104) /* Panel Read Status Register */ + +#define LCCR3_1BPP (0 << 24) +#define LCCR3_2BPP (1 << 24) +#define LCCR3_4BPP (2 << 24) +#define LCCR3_8BPP (3 << 24) +#define LCCR3_16BPP (4 << 24) +#define LCCR3_18BPP (5 << 24) +#define LCCR3_18BPP_P (6 << 24) +#define LCCR3_19BPP (7 << 24) +#define LCCR3_19BPP_P (1 << 29) +#define LCCR3_24BPP ((1 << 29) | (1 << 24)) +#define LCCR3_25BPP ((1 << 29) | (2 << 24)) + +#define LCCR3_PDFOR_0 (0 << 30) +#define LCCR3_PDFOR_1 (1 << 30) +#define LCCR3_PDFOR_2 (2 << 30) +#define LCCR3_PDFOR_3 (3 << 30) + +#define LCCR4_PAL_FOR_0 (0 << 15) +#define LCCR4_PAL_FOR_1 (1 << 15) +#define LCCR4_PAL_FOR_2 (2 << 15) +#define LCCR4_PAL_FOR_MASK (3 << 15) + +#define FDADR0 (0x200) /* DMA Channel 0 Frame Descriptor Address Register */ +#define FSADR0 (0x204) /* DMA Channel 0 Frame Source Address Register */ +#define FIDR0 (0x208) /* DMA Channel 0 Frame ID Register */ +#define LDCMD0 (0x20C) /* DMA Channel 0 Command Register */ +#define FDADR1 (0x210) /* DMA Channel 1 Frame Descriptor Address Register */ +#define FSADR1 (0x214) /* DMA Channel 1 Frame Source Address Register */ +#define FIDR1 (0x218) /* DMA Channel 1 Frame ID Register */ +#define LDCMD1 (0x21C) /* DMA Channel 1 Command Register */ +#define FDADR6 (0x260) /* DMA Channel 6 Frame Descriptor Address Register */ +#define FSADR6 (0x264) /* DMA Channel 6 Frame Source Address Register */ +#define FIDR6 (0x268) /* DMA Channel 6 Frame ID Register */ + +#define LCCR0_ENB (1 << 0) /* LCD Controller enable */ +#define LCCR0_CMS (1 << 1) /* Color/Monochrome Display Select */ +#define LCCR0_Color (LCCR0_CMS*0) /* Color display */ +#define LCCR0_Mono (LCCR0_CMS*1) /* Monochrome display */ +#define LCCR0_SDS (1 << 2) /* Single/Dual Panel Display Select */ +#define LCCR0_Sngl (LCCR0_SDS*0) /* Single panel display */ +#define LCCR0_Dual (LCCR0_SDS*1) /* Dual panel display */ + +#define LCCR0_LDM (1 << 3) /* LCD Disable Done Mask */ +#define LCCR0_SFM (1 << 4) /* Start of frame mask */ +#define LCCR0_IUM (1 << 5) /* Input FIFO underrun mask */ +#define LCCR0_EFM (1 << 6) /* End of Frame mask */ +#define LCCR0_PAS (1 << 7) /* Passive/Active display Select */ +#define LCCR0_Pas (LCCR0_PAS*0) /* Passive display (STN) */ +#define LCCR0_Act (LCCR0_PAS*1) /* Active display (TFT) */ +#define LCCR0_DPD (1 << 9) /* Double Pixel Data (monochrome) */ +#define LCCR0_4PixMono (LCCR0_DPD*0) /* 4-Pixel/clock Monochrome display */ +#define LCCR0_8PixMono (LCCR0_DPD*1) /* 8-Pixel/clock Monochrome display */ +#define LCCR0_DIS (1 << 10) /* LCD Disable */ +#define LCCR0_QDM (1 << 11) /* LCD Quick Disable mask */ +#define LCCR0_PDD (0xff << 12) /* Palette DMA request delay */ +#define LCCR0_PDD_S 12 +#define LCCR0_BM (1 << 20) /* Branch mask */ +#define LCCR0_OUM (1 << 21) /* Output FIFO underrun mask */ +#define LCCR0_LCDT (1 << 22) /* LCD panel type */ +#define LCCR0_RDSTM (1 << 23) /* Read status interrupt mask */ +#define LCCR0_CMDIM (1 << 24) /* Command interrupt mask */ +#define LCCR0_OUC (1 << 25) /* Overlay Underlay control bit */ +#define LCCR0_LDDALT (1 << 26) /* LDD alternate mapping control */ + +#define LCCR1_PPL Fld (10, 0) /* Pixels Per Line - 1 */ +#define LCCR1_DisWdth(Pixel) (((Pixel) - 1) << FShft (LCCR1_PPL)) + +#define LCCR1_HSW Fld (6, 10) /* Horizontal Synchronization */ +#define LCCR1_HorSnchWdth(Tpix) (((Tpix) - 1) << FShft (LCCR1_HSW)) + +#define LCCR1_ELW Fld (8, 16) /* End-of-Line pixel clock Wait - 1 */ +#define LCCR1_EndLnDel(Tpix) (((Tpix) - 1) << FShft (LCCR1_ELW)) + +#define LCCR1_BLW Fld (8, 24) /* Beginning-of-Line pixel clock */ +#define LCCR1_BegLnDel(Tpix) (((Tpix) - 1) << FShft (LCCR1_BLW)) + +#define LCCR2_LPP Fld (10, 0) /* Line Per Panel - 1 */ +#define LCCR2_DisHght(Line) (((Line) - 1) << FShft (LCCR2_LPP)) + +#define LCCR2_VSW Fld (6, 10) /* Vertical Synchronization pulse - 1 */ +#define LCCR2_VrtSnchWdth(Tln) (((Tln) - 1) << FShft (LCCR2_VSW)) + +#define LCCR2_EFW Fld (8, 16) /* End-of-Frame line clock Wait */ +#define LCCR2_EndFrmDel(Tln) ((Tln) << FShft (LCCR2_EFW)) + +#define LCCR2_BFW Fld (8, 24) /* Beginning-of-Frame line clock */ +#define LCCR2_BegFrmDel(Tln) ((Tln) << FShft (LCCR2_BFW)) + +#define LCCR3_API (0xf << 16) /* AC Bias pin trasitions per interrupt */ +#define LCCR3_API_S 16 +#define LCCR3_VSP (1 << 20) /* vertical sync polarity */ +#define LCCR3_HSP (1 << 21) /* horizontal sync polarity */ +#define LCCR3_PCP (1 << 22) /* Pixel Clock Polarity (L_PCLK) */ +#define LCCR3_PixRsEdg (LCCR3_PCP*0) /* Pixel clock Rising-Edge */ +#define LCCR3_PixFlEdg (LCCR3_PCP*1) /* Pixel clock Falling-Edge */ + +#define LCCR3_OEP (1 << 23) /* Output Enable Polarity */ +#define LCCR3_OutEnH (LCCR3_OEP*0) /* Output Enable active High */ +#define LCCR3_OutEnL (LCCR3_OEP*1) /* Output Enable active Low */ + +#define LCCR3_DPC (1 << 27) /* double pixel clock mode */ +#define LCCR3_PCD Fld (8, 0) /* Pixel Clock Divisor */ +#define LCCR3_PixClkDiv(Div) (((Div) << FShft (LCCR3_PCD))) + +#define LCCR3_BPP Fld (3, 24) /* Bit Per Pixel */ +#define LCCR3_Bpp(Bpp) (((Bpp) << FShft (LCCR3_BPP))) + +#define LCCR3_ACB Fld (8, 8) /* AC Bias */ +#define LCCR3_Acb(Acb) (((Acb) << FShft (LCCR3_ACB))) + +#define LCCR3_HorSnchH (LCCR3_HSP*0) /* HSP Active High */ +#define LCCR3_HorSnchL (LCCR3_HSP*1) /* HSP Active Low */ + +#define LCCR3_VrtSnchH (LCCR3_VSP*0) /* VSP Active High */ +#define LCCR3_VrtSnchL (LCCR3_VSP*1) /* VSP Active Low */ + +#define LCCR5_IUM(x) (1 << ((x) + 23)) /* input underrun mask */ +#define LCCR5_BSM(x) (1 << ((x) + 15)) /* branch mask */ +#define LCCR5_EOFM(x) (1 << ((x) + 7)) /* end of frame mask */ +#define LCCR5_SOFM(x) (1 << ((x) + 0)) /* start of frame mask */ + +#define LCSR_LDD (1 << 0) /* LCD Disable Done */ +#define LCSR_SOF (1 << 1) /* Start of frame */ +#define LCSR_BER (1 << 2) /* Bus error */ +#define LCSR_ABC (1 << 3) /* AC Bias count */ +#define LCSR_IUL (1 << 4) /* input FIFO underrun Lower panel */ +#define LCSR_IUU (1 << 5) /* input FIFO underrun Upper panel */ +#define LCSR_OU (1 << 6) /* output FIFO underrun */ +#define LCSR_QD (1 << 7) /* quick disable */ +#define LCSR_EOF (1 << 8) /* end of frame */ +#define LCSR_BS (1 << 9) /* branch status */ +#define LCSR_SINT (1 << 10) /* subsequent interrupt */ +#define LCSR_RD_ST (1 << 11) /* read status */ +#define LCSR_CMD_INT (1 << 12) /* command interrupt */ + +#define LDCMD_PAL (1 << 26) /* instructs DMA to load palette buffer */ + +/* smartpanel related */ +#define PRSR_DATA(x) ((x) & 0xff) /* Panel Data */ +#define PRSR_A0 (1 << 8) /* Read Data Source */ +#define PRSR_ST_OK (1 << 9) /* Status OK */ +#define PRSR_CON_NT (1 << 10) /* Continue to Next Command */ + +#define SMART_CMD_A0 (0x1 << 8) +#define SMART_CMD_READ_STATUS_REG (0x0 << 9) +#define SMART_CMD_READ_FRAME_BUFFER ((0x0 << 9) | SMART_CMD_A0) +#define SMART_CMD_WRITE_COMMAND (0x1 << 9) +#define SMART_CMD_WRITE_DATA ((0x1 << 9) | SMART_CMD_A0) +#define SMART_CMD_WRITE_FRAME ((0x2 << 9) | SMART_CMD_A0) +#define SMART_CMD_WAIT_FOR_VSYNC (0x3 << 9) +#define SMART_CMD_NOOP (0x4 << 9) +#define SMART_CMD_INTERRUPT (0x5 << 9) + +#define SMART_CMD(x) (SMART_CMD_WRITE_COMMAND | ((x) & 0xff)) +#define SMART_DAT(x) (SMART_CMD_WRITE_DATA | ((x) & 0xff)) +#endif /* __ASM_ARCH_REGS_LCD_H */ diff --git a/arch/arm/mach-pxa/include/mach/regs-ssp.h b/arch/arm/mach-pxa/include/mach/regs-ssp.h new file mode 100644 index 00000000000..3c04cde2cf1 --- /dev/null +++ b/arch/arm/mach-pxa/include/mach/regs-ssp.h @@ -0,0 +1,127 @@ +#ifndef __ASM_ARCH_REGS_SSP_H +#define __ASM_ARCH_REGS_SSP_H + +/* + * SSP Serial Port Registers + * PXA250, PXA255, PXA26x and PXA27x SSP controllers are all slightly different. + * PXA255, PXA26x and PXA27x have extra ports, registers and bits. + */ + +#define SSCR0 (0x00) /* SSP Control Register 0 */ +#define SSCR1 (0x04) /* SSP Control Register 1 */ +#define SSSR (0x08) /* SSP Status Register */ +#define SSITR (0x0C) /* SSP Interrupt Test Register */ +#define SSDR (0x10) /* SSP Data Write/Data Read Register */ + +#define SSTO (0x28) /* SSP Time Out Register */ +#define SSPSP (0x2C) /* SSP Programmable Serial Protocol */ +#define SSTSA (0x30) /* SSP Tx Timeslot Active */ +#define SSRSA (0x34) /* SSP Rx Timeslot Active */ +#define SSTSS (0x38) /* SSP Timeslot Status */ +#define SSACD (0x3C) /* SSP Audio Clock Divider */ + +#if defined(CONFIG_PXA3xx) +#define SSACDD (0x40) /* SSP Audio Clock Dither Divider */ +#endif + +/* Common PXA2xx bits first */ +#define SSCR0_DSS (0x0000000f) /* Data Size Select (mask) */ +#define SSCR0_DataSize(x) ((x) - 1) /* Data Size Select [4..16] */ +#define SSCR0_FRF (0x00000030) /* FRame Format (mask) */ +#define SSCR0_Motorola (0x0 << 4) /* Motorola's Serial Peripheral Interface (SPI) */ +#define SSCR0_TI (0x1 << 4) /* Texas Instruments' Synchronous Serial Protocol (SSP) */ +#define SSCR0_National (0x2 << 4) /* National Microwire */ +#define SSCR0_ECS (1 << 6) /* External clock select */ +#define SSCR0_SSE (1 << 7) /* Synchronous Serial Port Enable */ + +#if defined(CONFIG_PXA25x) +#define SSCR0_SCR (0x0000ff00) /* Serial Clock Rate (mask) */ +#define SSCR0_SerClkDiv(x) ((((x) - 2)/2) << 8) /* Divisor [2..512] */ + +#elif defined(CONFIG_PXA27x) || defined(CONFIG_PXA3xx) +#define SSCR0_SCR (0x000fff00) /* Serial Clock Rate (mask) */ +#define SSCR0_SerClkDiv(x) (((x) - 1) << 8) /* Divisor [1..4096] */ +#define SSCR0_EDSS (1 << 20) /* Extended data size select */ +#define SSCR0_NCS (1 << 21) /* Network clock select */ +#define SSCR0_RIM (1 << 22) /* Receive FIFO overrrun interrupt mask */ +#define SSCR0_TUM (1 << 23) /* Transmit FIFO underrun interrupt mask */ +#define SSCR0_FRDC (0x07000000) /* Frame rate divider control (mask) */ +#define SSCR0_SlotsPerFrm(x) (((x) - 1) << 24) /* Time slots per frame [1..8] */ +#define SSCR0_ADC (1 << 30) /* Audio clock select */ +#define SSCR0_MOD (1 << 31) /* Mode (normal or network) */ +#endif + +#if defined(CONFIG_PXA3xx) +#define SSCR0_FPCKE (1 << 29) /* FIFO packing enable */ +#endif + +#define SSCR1_RIE (1 << 0) /* Receive FIFO Interrupt Enable */ +#define SSCR1_TIE (1 << 1) /* Transmit FIFO Interrupt Enable */ +#define SSCR1_LBM (1 << 2) /* Loop-Back Mode */ +#define SSCR1_SPO (1 << 3) /* Motorola SPI SSPSCLK polarity setting */ +#define SSCR1_SPH (1 << 4) /* Motorola SPI SSPSCLK phase setting */ +#define SSCR1_MWDS (1 << 5) /* Microwire Transmit Data Size */ +#define SSCR1_TFT (0x000003c0) /* Transmit FIFO Threshold (mask) */ +#define SSCR1_TxTresh(x) (((x) - 1) << 6) /* level [1..16] */ +#define SSCR1_RFT (0x00003c00) /* Receive FIFO Threshold (mask) */ +#define SSCR1_RxTresh(x) (((x) - 1) << 10) /* level [1..16] */ + +#define SSSR_TNF (1 << 2) /* Transmit FIFO Not Full */ +#define SSSR_RNE (1 << 3) /* Receive FIFO Not Empty */ +#define SSSR_BSY (1 << 4) /* SSP Busy */ +#define SSSR_TFS (1 << 5) /* Transmit FIFO Service Request */ +#define SSSR_RFS (1 << 6) /* Receive FIFO Service Request */ +#define SSSR_ROR (1 << 7) /* Receive FIFO Overrun */ + +#define SSCR0_TIM (1 << 23) /* Transmit FIFO Under Run Interrupt Mask */ +#define SSCR0_RIM (1 << 22) /* Receive FIFO Over Run interrupt Mask */ +#define SSCR0_NCS (1 << 21) /* Network Clock Select */ +#define SSCR0_EDSS (1 << 20) /* Extended Data Size Select */ + +/* extra bits in PXA255, PXA26x and PXA27x SSP ports */ +#define SSCR0_TISSP (1 << 4) /* TI Sync Serial Protocol */ +#define SSCR0_PSP (3 << 4) /* PSP - Programmable Serial Protocol */ +#define SSCR1_TTELP (1 << 31) /* TXD Tristate Enable Last Phase */ +#define SSCR1_TTE (1 << 30) /* TXD Tristate Enable */ +#define SSCR1_EBCEI (1 << 29) /* Enable Bit Count Error interrupt */ +#define SSCR1_SCFR (1 << 28) /* Slave Clock free Running */ +#define SSCR1_ECRA (1 << 27) /* Enable Clock Request A */ +#define SSCR1_ECRB (1 << 26) /* Enable Clock request B */ +#define SSCR1_SCLKDIR (1 << 25) /* Serial Bit Rate Clock Direction */ +#define SSCR1_SFRMDIR (1 << 24) /* Frame Direction */ +#define SSCR1_RWOT (1 << 23) /* Receive Without Transmit */ +#define SSCR1_TRAIL (1 << 22) /* Trailing Byte */ +#define SSCR1_TSRE (1 << 21) /* Transmit Service Request Enable */ +#define SSCR1_RSRE (1 << 20) /* Receive Service Request Enable */ +#define SSCR1_TINTE (1 << 19) /* Receiver Time-out Interrupt enable */ +#define SSCR1_PINTE (1 << 18) /* Peripheral Trailing Byte Interupt Enable */ +#define SSCR1_IFS (1 << 16) /* Invert Frame Signal */ +#define SSCR1_STRF (1 << 15) /* Select FIFO or EFWR */ +#define SSCR1_EFWR (1 << 14) /* Enable FIFO Write/Read */ + +#define SSSR_BCE (1 << 23) /* Bit Count Error */ +#define SSSR_CSS (1 << 22) /* Clock Synchronisation Status */ +#define SSSR_TUR (1 << 21) /* Transmit FIFO Under Run */ +#define SSSR_EOC (1 << 20) /* End Of Chain */ +#define SSSR_TINT (1 << 19) /* Receiver Time-out Interrupt */ +#define SSSR_PINT (1 << 18) /* Peripheral Trailing Byte Interrupt */ + +#define SSPSP_FSRT (1 << 25) /* Frame Sync Relative Timing */ +#define SSPSP_DMYSTOP(x) ((x) << 23) /* Dummy Stop */ +#define SSPSP_SFRMWDTH(x) ((x) << 16) /* Serial Frame Width */ +#define SSPSP_SFRMDLY(x) ((x) << 9) /* Serial Frame Delay */ +#define SSPSP_DMYSTRT(x) ((x) << 7) /* Dummy Start */ +#define SSPSP_STRTDLY(x) ((x) << 4) /* Start Delay */ +#define SSPSP_ETDS (1 << 3) /* End of Transfer data State */ +#define SSPSP_SFRMP (1 << 2) /* Serial Frame Polarity */ +#define SSPSP_SCMODE(x) ((x) << 0) /* Serial Bit Rate Clock Mode */ + +#define SSACD_SCDB (1 << 3) /* SSPSYSCLK Divider Bypass */ +#define SSACD_ACPS(x) ((x) << 4) /* Audio clock PLL select */ +#define SSACD_ACDS(x) ((x) << 0) /* Audio clock divider select */ +#if defined(CONFIG_PXA3xx) +#define SSACD_SCDX8 (1 << 7) /* SYSCLK division ratio select */ +#endif + + +#endif /* __ASM_ARCH_REGS_SSP_H */ diff --git a/arch/arm/mach-pxa/include/mach/reset.h b/arch/arm/mach-pxa/include/mach/reset.h new file mode 100644 index 00000000000..7b8842cfa5f --- /dev/null +++ b/arch/arm/mach-pxa/include/mach/reset.h @@ -0,0 +1,21 @@ +#ifndef __ASM_ARCH_RESET_H +#define __ASM_ARCH_RESET_H + +#define RESET_STATUS_HARDWARE (1 << 0) /* Hardware Reset */ +#define RESET_STATUS_WATCHDOG (1 << 1) /* Watchdog Reset */ +#define RESET_STATUS_LOWPOWER (1 << 2) /* Low Power/Sleep Exit */ +#define RESET_STATUS_GPIO (1 << 3) /* GPIO Reset */ +#define RESET_STATUS_ALL (0xf) + +extern unsigned int reset_status; +extern void clear_reset_status(unsigned int mask); + +/** + * init_gpio_reset() - register GPIO as reset generator + * + * @gpio - gpio nr + * @output - set gpio as out/low instead of input during normal work + */ +extern int init_gpio_reset(int gpio, int output); + +#endif /* __ASM_ARCH_RESET_H */ diff --git a/arch/arm/mach-pxa/include/mach/sharpsl.h b/arch/arm/mach-pxa/include/mach/sharpsl.h new file mode 100644 index 00000000000..3b1d4a72d4d --- /dev/null +++ b/arch/arm/mach-pxa/include/mach/sharpsl.h @@ -0,0 +1,34 @@ +/* + * SharpSL SSP Driver + */ + +unsigned long corgi_ssp_ads7846_putget(unsigned long); +unsigned long corgi_ssp_ads7846_get(void); +void corgi_ssp_ads7846_put(unsigned long data); +void corgi_ssp_ads7846_lock(void); +void corgi_ssp_ads7846_unlock(void); +void corgi_ssp_lcdtg_send (unsigned char adrs, unsigned char data); +void corgi_ssp_blduty_set(int duty); +int corgi_ssp_max1111_get(unsigned long data); + +/* + * SharpSL Touchscreen Driver + */ + +struct corgits_machinfo { + unsigned long (*get_hsync_invperiod)(void); + void (*put_hsync)(void); + void (*wait_hsync)(void); +}; + + +/* + * SharpSL Backlight + */ +extern void corgibl_limit_intensity(int limit); + + +/* + * SharpSL Battery/PM Driver + */ +extern void sharpsl_battery_kick(void); diff --git a/arch/arm/mach-pxa/include/mach/spitz.h b/arch/arm/mach-pxa/include/mach/spitz.h new file mode 100644 index 00000000000..31ac26b55bc --- /dev/null +++ b/arch/arm/mach-pxa/include/mach/spitz.h @@ -0,0 +1,190 @@ +/* + * Hardware specific definitions for SL-Cx000 series of PDAs + * + * Copyright (c) 2005 Alexander Wykes + * Copyright (c) 2005 Richard Purdie + * + * Based on Sharp's 2.4 kernel patches + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + * + */ +#ifndef __ASM_ARCH_SPITZ_H +#define __ASM_ARCH_SPITZ_H 1 +#endif + +#include <linux/fb.h> +#include <linux/gpio.h> + +/* Spitz/Akita GPIOs */ + +#define SPITZ_GPIO_KEY_INT (0) /* Key Interrupt */ +#define SPITZ_GPIO_RESET (1) +#define SPITZ_GPIO_nSD_DETECT (9) +#define SPITZ_GPIO_TP_INT (11) /* Touch Panel interrupt */ +#define SPITZ_GPIO_AK_INT (13) /* Remote Control */ +#define SPITZ_GPIO_ADS7846_CS (14) +#define SPITZ_GPIO_SYNC (16) +#define SPITZ_GPIO_MAX1111_CS (20) +#define SPITZ_GPIO_FATAL_BAT (21) +#define SPITZ_GPIO_HSYNC (22) +#define SPITZ_GPIO_nSD_CLK (32) +#define SPITZ_GPIO_USB_DEVICE (35) +#define SPITZ_GPIO_USB_HOST (37) +#define SPITZ_GPIO_USB_CONNECT (41) +#define SPITZ_GPIO_LCDCON_CS (53) +#define SPITZ_GPIO_nPCE (54) +#define SPITZ_GPIO_nSD_WP (81) +#define SPITZ_GPIO_ON_RESET (89) +#define SPITZ_GPIO_BAT_COVER (90) +#define SPITZ_GPIO_CF_CD (94) +#define SPITZ_GPIO_ON_KEY (95) +#define SPITZ_GPIO_SWA (97) +#define SPITZ_GPIO_SWB (96) +#define SPITZ_GPIO_CHRG_FULL (101) +#define SPITZ_GPIO_CO (101) +#define SPITZ_GPIO_CF_IRQ (105) +#define SPITZ_GPIO_AC_IN (115) +#define SPITZ_GPIO_HP_IN (116) + +/* Spitz Only GPIOs */ + +#define SPITZ_GPIO_CF2_IRQ (106) /* CF slot1 Ready */ +#define SPITZ_GPIO_CF2_CD (93) + + +/* Spitz/Akita Keyboard Definitions */ + +#define SPITZ_KEY_STROBE_NUM (11) +#define SPITZ_KEY_SENSE_NUM (7) +#define SPITZ_GPIO_G0_STROBE_BIT 0x0f800000 +#define SPITZ_GPIO_G1_STROBE_BIT 0x00100000 +#define SPITZ_GPIO_G2_STROBE_BIT 0x01000000 +#define SPITZ_GPIO_G3_STROBE_BIT 0x00041880 +#define SPITZ_GPIO_G0_SENSE_BIT 0x00021000 +#define SPITZ_GPIO_G1_SENSE_BIT 0x000000d4 +#define SPITZ_GPIO_G2_SENSE_BIT 0x08000000 +#define SPITZ_GPIO_G3_SENSE_BIT 0x00000000 + +#define SPITZ_GPIO_KEY_STROBE0 88 +#define SPITZ_GPIO_KEY_STROBE1 23 +#define SPITZ_GPIO_KEY_STROBE2 24 +#define SPITZ_GPIO_KEY_STROBE3 25 +#define SPITZ_GPIO_KEY_STROBE4 26 +#define SPITZ_GPIO_KEY_STROBE5 27 +#define SPITZ_GPIO_KEY_STROBE6 52 +#define SPITZ_GPIO_KEY_STROBE7 103 +#define SPITZ_GPIO_KEY_STROBE8 107 +#define SPITZ_GPIO_KEY_STROBE9 108 +#define SPITZ_GPIO_KEY_STROBE10 114 + +#define SPITZ_GPIO_KEY_SENSE0 12 +#define SPITZ_GPIO_KEY_SENSE1 17 +#define SPITZ_GPIO_KEY_SENSE2 91 +#define SPITZ_GPIO_KEY_SENSE3 34 +#define SPITZ_GPIO_KEY_SENSE4 36 +#define SPITZ_GPIO_KEY_SENSE5 38 +#define SPITZ_GPIO_KEY_SENSE6 39 + + +/* Spitz Scoop Device (No. 1) GPIOs */ +/* Suspend States in comments */ +#define SPITZ_SCP_LED_GREEN SCOOP_GPCR_PA11 /* Keep */ +#define SPITZ_SCP_JK_B SCOOP_GPCR_PA12 /* Keep */ +#define SPITZ_SCP_CHRG_ON SCOOP_GPCR_PA13 /* Keep */ +#define SPITZ_SCP_MUTE_L SCOOP_GPCR_PA14 /* Low */ +#define SPITZ_SCP_MUTE_R SCOOP_GPCR_PA15 /* Low */ +#define SPITZ_SCP_CF_POWER SCOOP_GPCR_PA16 /* Keep */ +#define SPITZ_SCP_LED_ORANGE SCOOP_GPCR_PA17 /* Keep */ +#define SPITZ_SCP_JK_A SCOOP_GPCR_PA18 /* Low */ +#define SPITZ_SCP_ADC_TEMP_ON SCOOP_GPCR_PA19 /* Low */ + +#define SPITZ_SCP_IO_DIR (SPITZ_SCP_JK_B | SPITZ_SCP_CHRG_ON | \ + SPITZ_SCP_MUTE_L | SPITZ_SCP_MUTE_R | \ + SPITZ_SCP_CF_POWER | SPITZ_SCP_JK_A | SPITZ_SCP_ADC_TEMP_ON) +#define SPITZ_SCP_IO_OUT (SPITZ_SCP_CHRG_ON | SPITZ_SCP_MUTE_L | SPITZ_SCP_MUTE_R) +#define SPITZ_SCP_SUS_CLR (SPITZ_SCP_MUTE_L | SPITZ_SCP_MUTE_R | SPITZ_SCP_JK_A | SPITZ_SCP_ADC_TEMP_ON) +#define SPITZ_SCP_SUS_SET 0 + +#define SPITZ_SCP_GPIO_BASE (NR_BUILTIN_GPIO) +#define SPITZ_GPIO_LED_GREEN (SPITZ_SCP_GPIO_BASE + 0) +#define SPITZ_GPIO_JK_B (SPITZ_SCP_GPIO_BASE + 1) +#define SPITZ_GPIO_CHRG_ON (SPITZ_SCP_GPIO_BASE + 2) +#define SPITZ_GPIO_MUTE_L (SPITZ_SCP_GPIO_BASE + 3) +#define SPITZ_GPIO_MUTE_R (SPITZ_SCP_GPIO_BASE + 4) +#define SPITZ_GPIO_CF_POWER (SPITZ_SCP_GPIO_BASE + 5) +#define SPITZ_GPIO_LED_ORANGE (SPITZ_SCP_GPIO_BASE + 6) +#define SPITZ_GPIO_JK_A (SPITZ_SCP_GPIO_BASE + 7) +#define SPITZ_GPIO_ADC_TEMP_ON (SPITZ_SCP_GPIO_BASE + 8) + +/* Spitz Scoop Device (No. 2) GPIOs */ +/* Suspend States in comments */ +#define SPITZ_SCP2_IR_ON SCOOP_GPCR_PA11 /* High */ +#define SPITZ_SCP2_AKIN_PULLUP SCOOP_GPCR_PA12 /* Keep */ +#define SPITZ_SCP2_RESERVED_1 SCOOP_GPCR_PA13 /* High */ +#define SPITZ_SCP2_RESERVED_2 SCOOP_GPCR_PA14 /* Low */ +#define SPITZ_SCP2_RESERVED_3 SCOOP_GPCR_PA15 /* Low */ +#define SPITZ_SCP2_RESERVED_4 SCOOP_GPCR_PA16 /* Low */ +#define SPITZ_SCP2_BACKLIGHT_CONT SCOOP_GPCR_PA17 /* Low */ +#define SPITZ_SCP2_BACKLIGHT_ON SCOOP_GPCR_PA18 /* Low */ +#define SPITZ_SCP2_MIC_BIAS SCOOP_GPCR_PA19 /* Low */ + +#define SPITZ_SCP2_IO_DIR (SPITZ_SCP2_AKIN_PULLUP | SPITZ_SCP2_RESERVED_1 | \ + SPITZ_SCP2_RESERVED_2 | SPITZ_SCP2_RESERVED_3 | SPITZ_SCP2_RESERVED_4 | \ + SPITZ_SCP2_BACKLIGHT_CONT | SPITZ_SCP2_BACKLIGHT_ON | SPITZ_SCP2_MIC_BIAS) + +#define SPITZ_SCP2_IO_OUT (SPITZ_SCP2_AKIN_PULLUP | SPITZ_SCP2_RESERVED_1) +#define SPITZ_SCP2_SUS_CLR (SPITZ_SCP2_RESERVED_2 | SPITZ_SCP2_RESERVED_3 | SPITZ_SCP2_RESERVED_4 | \ + SPITZ_SCP2_BACKLIGHT_CONT | SPITZ_SCP2_BACKLIGHT_ON | SPITZ_SCP2_MIC_BIAS) +#define SPITZ_SCP2_SUS_SET (SPITZ_SCP2_IR_ON | SPITZ_SCP2_RESERVED_1) + +#define SPITZ_SCP2_GPIO_BASE (NR_BUILTIN_GPIO + 12) +#define SPITZ_GPIO_IR_ON (SPITZ_SCP2_GPIO_BASE + 0) +#define SPITZ_GPIO_AKIN_PULLUP (SPITZ_SCP2_GPIO_BASE + 1 +#define SPITZ_GPIO_RESERVED_1 (SPITZ_SCP2_GPIO_BASE + 2) +#define SPITZ_GPIO_RESERVED_2 (SPITZ_SCP2_GPIO_BASE + 3) +#define SPITZ_GPIO_RESERVED_3 (SPITZ_SCP2_GPIO_BASE + 4) +#define SPITZ_GPIO_RESERVED_4 (SPITZ_SCP2_GPIO_BASE + 5) +#define SPITZ_GPIO_BACKLIGHT_CONT (SPITZ_SCP2_GPIO_BASE + 6) +#define SPITZ_GPIO_BACKLIGHT_ON (SPITZ_SCP2_GPIO_BASE + 7) +#define SPITZ_GPIO_MIC_BIAS (SPITZ_SCP2_GPIO_BASE + 8) + +/* Akita IO Expander GPIOs */ +#define AKITA_IOEXP_GPIO_BASE (NR_BUILTIN_GPIO + 12) +#define AKITA_GPIO_RESERVED_0 (AKITA_IOEXP_GPIO_BASE + 0) +#define AKITA_GPIO_RESERVED_1 (AKITA_IOEXP_GPIO_BASE + 1) +#define AKITA_GPIO_MIC_BIAS (AKITA_IOEXP_GPIO_BASE + 2) +#define AKITA_GPIO_BACKLIGHT_ON (AKITA_IOEXP_GPIO_BASE + 3) +#define AKITA_GPIO_BACKLIGHT_CONT (AKITA_IOEXP_GPIO_BASE + 4) +#define AKITA_GPIO_AKIN_PULLUP (AKITA_IOEXP_GPIO_BASE + 5) +#define AKITA_GPIO_IR_ON (AKITA_IOEXP_GPIO_BASE + 6) +#define AKITA_GPIO_RESERVED_7 (AKITA_IOEXP_GPIO_BASE + 7) + +/* Spitz IRQ Definitions */ + +#define SPITZ_IRQ_GPIO_KEY_INT IRQ_GPIO(SPITZ_GPIO_KEY_INT) +#define SPITZ_IRQ_GPIO_AC_IN IRQ_GPIO(SPITZ_GPIO_AC_IN) +#define SPITZ_IRQ_GPIO_AK_INT IRQ_GPIO(SPITZ_GPIO_AK_INT) +#define SPITZ_IRQ_GPIO_HP_IN IRQ_GPIO(SPITZ_GPIO_HP_IN) +#define SPITZ_IRQ_GPIO_TP_INT IRQ_GPIO(SPITZ_GPIO_TP_INT) +#define SPITZ_IRQ_GPIO_SYNC IRQ_GPIO(SPITZ_GPIO_SYNC) +#define SPITZ_IRQ_GPIO_ON_KEY IRQ_GPIO(SPITZ_GPIO_ON_KEY) +#define SPITZ_IRQ_GPIO_SWA IRQ_GPIO(SPITZ_GPIO_SWA) +#define SPITZ_IRQ_GPIO_SWB IRQ_GPIO(SPITZ_GPIO_SWB) +#define SPITZ_IRQ_GPIO_BAT_COVER IRQ_GPIO(SPITZ_GPIO_BAT_COVER) +#define SPITZ_IRQ_GPIO_FATAL_BAT IRQ_GPIO(SPITZ_GPIO_FATAL_BAT) +#define SPITZ_IRQ_GPIO_CO IRQ_GPIO(SPITZ_GPIO_CO) +#define SPITZ_IRQ_GPIO_CF_IRQ IRQ_GPIO(SPITZ_GPIO_CF_IRQ) +#define SPITZ_IRQ_GPIO_CF_CD IRQ_GPIO(SPITZ_GPIO_CF_CD) +#define SPITZ_IRQ_GPIO_CF2_IRQ IRQ_GPIO(SPITZ_GPIO_CF2_IRQ) +#define SPITZ_IRQ_GPIO_nSD_INT IRQ_GPIO(SPITZ_GPIO_nSD_INT) +#define SPITZ_IRQ_GPIO_nSD_DETECT IRQ_GPIO(SPITZ_GPIO_nSD_DETECT) + +/* + * Shared data structures + */ +extern struct platform_device spitzscoop_device; +extern struct platform_device spitzscoop2_device; +extern struct sharpsl_charger_machinfo spitz_pm_machinfo; diff --git a/arch/arm/mach-pxa/include/mach/ssp.h b/arch/arm/mach-pxa/include/mach/ssp.h new file mode 100644 index 00000000000..cb5cb766f0f --- /dev/null +++ b/arch/arm/mach-pxa/include/mach/ssp.h @@ -0,0 +1,107 @@ +/* + * ssp.h + * + * Copyright (C) 2003 Russell King, All Rights Reserved. + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + * + * This driver supports the following PXA CPU/SSP ports:- + * + * PXA250 SSP + * PXA255 SSP, NSSP + * PXA26x SSP, NSSP, ASSP + * PXA27x SSP1, SSP2, SSP3 + * PXA3xx SSP1, SSP2, SSP3, SSP4 + */ + +#ifndef __ASM_ARCH_SSP_H +#define __ASM_ARCH_SSP_H + +#include <linux/list.h> +#include <linux/io.h> + +enum pxa_ssp_type { + SSP_UNDEFINED = 0, + PXA25x_SSP, /* pxa 210, 250, 255, 26x */ + PXA25x_NSSP, /* pxa 255, 26x (including ASSP) */ + PXA27x_SSP, +}; + +struct ssp_device { + struct platform_device *pdev; + struct list_head node; + + struct clk *clk; + void __iomem *mmio_base; + unsigned long phys_base; + + const char *label; + int port_id; + int type; + int use_count; + int irq; + int drcmr_rx; + int drcmr_tx; +}; + +/* + * SSP initialisation flags + */ +#define SSP_NO_IRQ 0x1 /* don't register an irq handler in SSP driver */ + +struct ssp_state { + u32 cr0; + u32 cr1; + u32 to; + u32 psp; +}; + +struct ssp_dev { + struct ssp_device *ssp; + u32 port; + u32 mode; + u32 flags; + u32 psp_flags; + u32 speed; + int irq; +}; + +int ssp_write_word(struct ssp_dev *dev, u32 data); +int ssp_read_word(struct ssp_dev *dev, u32 *data); +int ssp_flush(struct ssp_dev *dev); +void ssp_enable(struct ssp_dev *dev); +void ssp_disable(struct ssp_dev *dev); +void ssp_save_state(struct ssp_dev *dev, struct ssp_state *ssp); +void ssp_restore_state(struct ssp_dev *dev, struct ssp_state *ssp); +int ssp_init(struct ssp_dev *dev, u32 port, u32 init_flags); +int ssp_config(struct ssp_dev *dev, u32 mode, u32 flags, u32 psp_flags, u32 speed); +void ssp_exit(struct ssp_dev *dev); + +/** + * ssp_write_reg - Write to a SSP register + * + * @dev: SSP device to access + * @reg: Register to write to + * @val: Value to be written. + */ +static inline void ssp_write_reg(struct ssp_device *dev, u32 reg, u32 val) +{ + __raw_writel(val, dev->mmio_base + reg); +} + +/** + * ssp_read_reg - Read from a SSP register + * + * @dev: SSP device to access + * @reg: Register to read from + */ +static inline u32 ssp_read_reg(struct ssp_device *dev, u32 reg) +{ + return __raw_readl(dev->mmio_base + reg); +} + +struct ssp_device *ssp_request(int port, const char *label); +void ssp_free(struct ssp_device *); +#endif /* __ASM_ARCH_SSP_H */ diff --git a/arch/arm/mach-pxa/include/mach/system.h b/arch/arm/mach-pxa/include/mach/system.h new file mode 100644 index 00000000000..0f381e69299 --- /dev/null +++ b/arch/arm/mach-pxa/include/mach/system.h @@ -0,0 +1,24 @@ +/* + * arch/arm/mach-pxa/include/mach/system.h + * + * Author: Nicolas Pitre + * Created: Jun 15, 2001 + * Copyright: MontaVista Software Inc. + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ + +#include <asm/proc-fns.h> +#include "hardware.h" +#include "pxa2xx-regs.h" +#include "pxa-regs.h" + +static inline void arch_idle(void) +{ + cpu_do_idle(); +} + + +void arch_reset(char mode); diff --git a/arch/arm/mach-pxa/include/mach/timex.h b/arch/arm/mach-pxa/include/mach/timex.h new file mode 100644 index 00000000000..b05fc6683c4 --- /dev/null +++ b/arch/arm/mach-pxa/include/mach/timex.h @@ -0,0 +1,26 @@ +/* + * arch/arm/mach-pxa/include/mach/timex.h + * + * Author: Nicolas Pitre + * Created: Jun 15, 2001 + * Copyright: MontaVista Software Inc. + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ + + +#if defined(CONFIG_PXA25x) +/* PXA250/210 timer base */ +#define CLOCK_TICK_RATE 3686400 +#elif defined(CONFIG_PXA27x) +/* PXA27x timer base */ +#ifdef CONFIG_MACH_MAINSTONE +#define CLOCK_TICK_RATE 3249600 +#else +#define CLOCK_TICK_RATE 3250000 +#endif +#else +#define CLOCK_TICK_RATE 3250000 +#endif diff --git a/arch/arm/mach-pxa/include/mach/tosa.h b/arch/arm/mach-pxa/include/mach/tosa.h new file mode 100644 index 00000000000..a72803f0461 --- /dev/null +++ b/arch/arm/mach-pxa/include/mach/tosa.h @@ -0,0 +1,198 @@ +/* + * Hardware specific definitions for Sharp SL-C6000x series of PDAs + * + * Copyright (c) 2005 Dirk Opfer + * + * Based on Sharp's 2.4 kernel patches + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + * + */ +#ifndef _ASM_ARCH_TOSA_H_ +#define _ASM_ARCH_TOSA_H_ 1 + +/* TOSA Chip selects */ +#define TOSA_LCDC_PHYS PXA_CS4_PHYS +/* Internel Scoop */ +#define TOSA_CF_PHYS (PXA_CS2_PHYS + 0x00800000) +/* Jacket Scoop */ +#define TOSA_SCOOP_PHYS (PXA_CS5_PHYS + 0x00800000) + +/* + * SCOOP2 internal GPIOs + */ +#define TOSA_SCOOP_GPIO_BASE NR_BUILTIN_GPIO +#define TOSA_SCOOP_PXA_VCORE1 SCOOP_GPCR_PA11 +#define TOSA_GPIO_TC6393XB_REST_IN (TOSA_SCOOP_GPIO_BASE + 1) +#define TOSA_GPIO_IR_POWERDWN (TOSA_SCOOP_GPIO_BASE + 2) +#define TOSA_GPIO_SD_WP (TOSA_SCOOP_GPIO_BASE + 3) +#define TOSA_GPIO_PWR_ON (TOSA_SCOOP_GPIO_BASE + 4) +#define TOSA_SCOOP_AUD_PWR_ON SCOOP_GPCR_PA16 +#define TOSA_GPIO_BT_RESET (TOSA_SCOOP_GPIO_BASE + 6) +#define TOSA_GPIO_BT_PWR_EN (TOSA_SCOOP_GPIO_BASE + 7) +#define TOSA_SCOOP_AC_IN_OL SCOOP_GPCR_PA19 + +/* GPIO Direction 1 : output mode / 0:input mode */ +#define TOSA_SCOOP_IO_DIR (TOSA_SCOOP_PXA_VCORE1 | \ + TOSA_SCOOP_AUD_PWR_ON) + +/* + * SCOOP2 jacket GPIOs + */ +#define TOSA_SCOOP_JC_GPIO_BASE (NR_BUILTIN_GPIO + 12) +#define TOSA_GPIO_BT_LED (TOSA_SCOOP_JC_GPIO_BASE + 0) +#define TOSA_GPIO_NOTE_LED (TOSA_SCOOP_JC_GPIO_BASE + 1) +#define TOSA_GPIO_CHRG_ERR_LED (TOSA_SCOOP_JC_GPIO_BASE + 2) +#define TOSA_GPIO_USB_PULLUP (TOSA_SCOOP_JC_GPIO_BASE + 3) +#define TOSA_GPIO_TC6393XB_SUSPEND (TOSA_SCOOP_JC_GPIO_BASE + 4) +#define TOSA_GPIO_TC6393XB_L3V_ON (TOSA_SCOOP_JC_GPIO_BASE + 5) +#define TOSA_SCOOP_JC_WLAN_DETECT SCOOP_GPCR_PA17 +#define TOSA_GPIO_WLAN_LED (TOSA_SCOOP_JC_GPIO_BASE + 7) +#define TOSA_SCOOP_JC_CARD_LIMIT_SEL SCOOP_GPCR_PA19 + +/* GPIO Direction 1 : output mode / 0:input mode */ +#define TOSA_SCOOP_JC_IO_DIR (TOSA_SCOOP_JC_CARD_LIMIT_SEL) + +/* + * TC6393XB GPIOs + */ +#define TOSA_TC6393XB_GPIO_BASE (NR_BUILTIN_GPIO + 2 * 12) +#define TOSA_TC6393XB_GPIO(i) (TOSA_TC6393XB_GPIO_BASE + (i)) +#define TOSA_TC6393XB_GPIO_BIT(gpio) (1 << (gpio - TOSA_TC6393XB_GPIO_BASE)) + +#define TOSA_GPIO_TG_ON (TOSA_TC6393XB_GPIO_BASE + 0) +#define TOSA_GPIO_L_MUTE (TOSA_TC6393XB_GPIO_BASE + 1) +#define TOSA_GPIO_BL_C20MA (TOSA_TC6393XB_GPIO_BASE + 3) +#define TOSA_GPIO_CARD_VCC_ON (TOSA_TC6393XB_GPIO_BASE + 4) +#define TOSA_GPIO_CHARGE_OFF (TOSA_TC6393XB_GPIO_BASE + 6) +#define TOSA_GPIO_CHARGE_OFF_JC (TOSA_TC6393XB_GPIO_BASE + 7) +#define TOSA_GPIO_BAT0_V_ON (TOSA_TC6393XB_GPIO_BASE + 9) +#define TOSA_GPIO_BAT1_V_ON (TOSA_TC6393XB_GPIO_BASE + 10) +#define TOSA_GPIO_BU_CHRG_ON (TOSA_TC6393XB_GPIO_BASE + 11) +#define TOSA_GPIO_BAT_SW_ON (TOSA_TC6393XB_GPIO_BASE + 12) +#define TOSA_GPIO_BAT0_TH_ON (TOSA_TC6393XB_GPIO_BASE + 14) +#define TOSA_GPIO_BAT1_TH_ON (TOSA_TC6393XB_GPIO_BASE + 15) + +/* + * Timing Generator + */ +#define TG_PNLCTL 0x00 +#define TG_TPOSCTL 0x01 +#define TG_DUTYCTL 0x02 +#define TG_GPOSR 0x03 +#define TG_GPODR1 0x04 +#define TG_GPODR2 0x05 +#define TG_PINICTL 0x06 +#define TG_HPOSCTL 0x07 + +/* + * PXA GPIOs + */ +#define TOSA_GPIO_POWERON (0) +#define TOSA_GPIO_RESET (1) +#define TOSA_GPIO_AC_IN (2) +#define TOSA_GPIO_RECORD_BTN (3) +#define TOSA_GPIO_SYNC (4) /* Cradle SYNC Button */ +#define TOSA_GPIO_USB_IN (5) +#define TOSA_GPIO_JACKET_DETECT (7) +#define TOSA_GPIO_nSD_DETECT (9) +#define TOSA_GPIO_nSD_INT (10) +#define TOSA_GPIO_TC6393XB_CLK (11) +#define TOSA_GPIO_BAT1_CRG (12) +#define TOSA_GPIO_CF_CD (13) +#define TOSA_GPIO_BAT0_CRG (14) +#define TOSA_GPIO_TC6393XB_INT (15) +#define TOSA_GPIO_BAT0_LOW (17) +#define TOSA_GPIO_TC6393XB_RDY (18) +#define TOSA_GPIO_ON_RESET (19) +#define TOSA_GPIO_EAR_IN (20) +#define TOSA_GPIO_CF_IRQ (21) /* CF slot0 Ready */ +#define TOSA_GPIO_ON_KEY (22) +#define TOSA_GPIO_VGA_LINE (27) +#define TOSA_GPIO_TP_INT (32) /* Touch Panel pen down interrupt */ +#define TOSA_GPIO_JC_CF_IRQ (36) /* CF slot1 Ready */ +#define TOSA_GPIO_BAT_LOCKED (38) /* Battery locked */ +#define TOSA_GPIO_IRDA_TX (47) +#define TOSA_GPIO_TG_SPI_SCLK (81) +#define TOSA_GPIO_TG_SPI_CS (82) +#define TOSA_GPIO_TG_SPI_MOSI (83) +#define TOSA_GPIO_BAT1_LOW (84) + +#define TOSA_GPIO_HP_IN GPIO_EAR_IN + +#define TOSA_GPIO_MAIN_BAT_LOW GPIO_BAT0_LOW + +#define TOSA_KEY_STROBE_NUM (11) +#define TOSA_KEY_SENSE_NUM (7) + +#define TOSA_GPIO_HIGH_STROBE_BIT (0xfc000000) +#define TOSA_GPIO_LOW_STROBE_BIT (0x0000001f) +#define TOSA_GPIO_ALL_SENSE_BIT (0x00000fe0) +#define TOSA_GPIO_ALL_SENSE_RSHIFT (5) +#define TOSA_GPIO_STROBE_BIT(a) GPIO_bit(58+(a)) +#define TOSA_GPIO_SENSE_BIT(a) GPIO_bit(69+(a)) +#define TOSA_GAFR_HIGH_STROBE_BIT (0xfff00000) +#define TOSA_GAFR_LOW_STROBE_BIT (0x000003ff) +#define TOSA_GAFR_ALL_SENSE_BIT (0x00fffc00) +#define TOSA_GPIO_KEY_SENSE(a) (69+(a)) +#define TOSA_GPIO_KEY_STROBE(a) (58+(a)) + +/* + * Interrupts + */ +#define TOSA_IRQ_GPIO_WAKEUP IRQ_GPIO(TOSA_GPIO_WAKEUP) +#define TOSA_IRQ_GPIO_AC_IN IRQ_GPIO(TOSA_GPIO_AC_IN) +#define TOSA_IRQ_GPIO_RECORD_BTN IRQ_GPIO(TOSA_GPIO_RECORD_BTN) +#define TOSA_IRQ_GPIO_SYNC IRQ_GPIO(TOSA_GPIO_SYNC) +#define TOSA_IRQ_GPIO_USB_IN IRQ_GPIO(TOSA_GPIO_USB_IN) +#define TOSA_IRQ_GPIO_JACKET_DETECT IRQ_GPIO(TOSA_GPIO_JACKET_DETECT) +#define TOSA_IRQ_GPIO_nSD_INT IRQ_GPIO(TOSA_GPIO_nSD_INT) +#define TOSA_IRQ_GPIO_nSD_DETECT IRQ_GPIO(TOSA_GPIO_nSD_DETECT) +#define TOSA_IRQ_GPIO_BAT1_CRG IRQ_GPIO(TOSA_GPIO_BAT1_CRG) +#define TOSA_IRQ_GPIO_CF_CD IRQ_GPIO(TOSA_GPIO_CF_CD) +#define TOSA_IRQ_GPIO_BAT0_CRG IRQ_GPIO(TOSA_GPIO_BAT0_CRG) +#define TOSA_IRQ_GPIO_TC6393XB_INT IRQ_GPIO(TOSA_GPIO_TC6393XB_INT) +#define TOSA_IRQ_GPIO_BAT0_LOW IRQ_GPIO(TOSA_GPIO_BAT0_LOW) +#define TOSA_IRQ_GPIO_EAR_IN IRQ_GPIO(TOSA_GPIO_EAR_IN) +#define TOSA_IRQ_GPIO_CF_IRQ IRQ_GPIO(TOSA_GPIO_CF_IRQ) +#define TOSA_IRQ_GPIO_ON_KEY IRQ_GPIO(TOSA_GPIO_ON_KEY) +#define TOSA_IRQ_GPIO_VGA_LINE IRQ_GPIO(TOSA_GPIO_VGA_LINE) +#define TOSA_IRQ_GPIO_TP_INT IRQ_GPIO(TOSA_GPIO_TP_INT) +#define TOSA_IRQ_GPIO_JC_CF_IRQ IRQ_GPIO(TOSA_GPIO_JC_CF_IRQ) +#define TOSA_IRQ_GPIO_BAT_LOCKED IRQ_GPIO(TOSA_GPIO_BAT_LOCKED) +#define TOSA_IRQ_GPIO_BAT1_LOW IRQ_GPIO(TOSA_GPIO_BAT1_LOW) +#define TOSA_IRQ_GPIO_KEY_SENSE(a) IRQ_GPIO(69+(a)) + +#define TOSA_IRQ_GPIO_MAIN_BAT_LOW IRQ_GPIO(TOSA_GPIO_MAIN_BAT_LOW) + +#define TOSA_KEY_SYNC KEY_102ND /* ??? */ + +#ifndef CONFIG_KEYBOARD_TOSA_USE_EXT_KEYCODES +#define TOSA_KEY_RECORD KEY_YEN +#define TOSA_KEY_ADDRESSBOOK KEY_KATAKANA +#define TOSA_KEY_CANCEL KEY_ESC +#define TOSA_KEY_CENTER KEY_HIRAGANA +#define TOSA_KEY_OK KEY_HENKAN +#define TOSA_KEY_CALENDAR KEY_KATAKANAHIRAGANA +#define TOSA_KEY_HOMEPAGE KEY_HANGEUL +#define TOSA_KEY_LIGHT KEY_MUHENKAN +#define TOSA_KEY_MENU KEY_HANJA +#define TOSA_KEY_FN KEY_RIGHTALT +#define TOSA_KEY_MAIL KEY_ZENKAKUHANKAKU +#else +#define TOSA_KEY_RECORD KEY_RECORD +#define TOSA_KEY_ADDRESSBOOK KEY_ADDRESSBOOK +#define TOSA_KEY_CANCEL KEY_CANCEL +#define TOSA_KEY_CENTER KEY_SELECT /* ??? */ +#define TOSA_KEY_OK KEY_OK +#define TOSA_KEY_CALENDAR KEY_CALENDAR +#define TOSA_KEY_HOMEPAGE KEY_HOMEPAGE +#define TOSA_KEY_LIGHT KEY_KBDILLUMTOGGLE +#define TOSA_KEY_MENU KEY_MENU +#define TOSA_KEY_FN KEY_FN +#define TOSA_KEY_MAIL KEY_MAIL +#endif + +#endif /* _ASM_ARCH_TOSA_H_ */ diff --git a/arch/arm/mach-pxa/include/mach/tosa_bt.h b/arch/arm/mach-pxa/include/mach/tosa_bt.h new file mode 100644 index 00000000000..efc3c3d3b75 --- /dev/null +++ b/arch/arm/mach-pxa/include/mach/tosa_bt.h @@ -0,0 +1,22 @@ +/* + * Tosa bluetooth built-in chip control. + * + * Later it may be shared with some other platforms. + * + * Copyright (c) 2008 Dmitry Baryshkov + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + * + */ +#ifndef TOSA_BT_H +#define TOSA_BT_H + +struct tosa_bt_data { + int gpio_pwr; + int gpio_reset; +}; + +#endif + diff --git a/arch/arm/mach-pxa/include/mach/trizeps4.h b/arch/arm/mach-pxa/include/mach/trizeps4.h new file mode 100644 index 00000000000..903e1a2e664 --- /dev/null +++ b/arch/arm/mach-pxa/include/mach/trizeps4.h @@ -0,0 +1,162 @@ +/************************************************************************ + * Include file for TRIZEPS4 SoM and ConXS eval-board + * Copyright (c) Jürgen Schindele + * 2006 + ************************************************************************/ + +/* + * Includes/Defines + */ +#ifndef _TRIPEPS4_H_ +#define _TRIPEPS4_H_ + +/* physical memory regions */ +#define TRIZEPS4_FLASH_PHYS (PXA_CS0_PHYS) /* Flash region */ +#define TRIZEPS4_DISK_PHYS (PXA_CS1_PHYS) /* Disk On Chip region */ +#define TRIZEPS4_ETH_PHYS (PXA_CS2_PHYS) /* Ethernet DM9000 region */ +#define TRIZEPS4_PIC_PHYS (PXA_CS3_PHYS) /* Logic chip on ConXS-Board */ +#define TRIZEPS4_SDRAM_BASE 0xa0000000 /* SDRAM region */ + + /* Logic on ConXS-board CSFR register*/ +#define TRIZEPS4_CFSR_PHYS (PXA_CS3_PHYS) + /* Logic on ConXS-board BOCR register*/ +#define TRIZEPS4_BOCR_PHYS (PXA_CS3_PHYS+0x02000000) + /* Logic on ConXS-board IRCR register*/ +#define TRIZEPS4_IRCR_PHYS (PXA_CS3_PHYS+0x02400000) + /* Logic on ConXS-board UPSR register*/ +#define TRIZEPS4_UPSR_PHYS (PXA_CS3_PHYS+0x02800000) + /* Logic on ConXS-board DICR register*/ +#define TRIZEPS4_DICR_PHYS (PXA_CS3_PHYS+0x03800000) + +/* virtual memory regions */ +#define TRIZEPS4_DISK_VIRT 0xF0000000 /* Disk On Chip region */ + +#define TRIZEPS4_PIC_VIRT 0xF0100000 /* not used */ +#define TRIZEPS4_CFSR_VIRT 0xF0100000 +#define TRIZEPS4_BOCR_VIRT 0xF0200000 +#define TRIZEPS4_DICR_VIRT 0xF0300000 +#define TRIZEPS4_IRCR_VIRT 0xF0400000 +#define TRIZEPS4_UPSR_VIRT 0xF0500000 + +/* size of flash */ +#define TRIZEPS4_FLASH_SIZE 0x02000000 /* Flash size 32 MB */ + +/* Ethernet Controller Davicom DM9000 */ +#define GPIO_DM9000 101 +#define TRIZEPS4_ETH_IRQ IRQ_GPIO(GPIO_DM9000) + +/* UCB1400 audio / TS-controller */ +#define GPIO_UCB1400 1 +#define TRIZEPS4_UCB1400_IRQ IRQ_GPIO(GPIO_UCB1400) + +/* PCMCIA socket Compact Flash */ +#define GPIO_PCD 11 /* PCMCIA Card Detect */ +#define TRIZEPS4_CD_IRQ IRQ_GPIO(GPIO_PCD) +#define GPIO_PRDY 13 /* READY / nINT */ +#define TRIZEPS4_READY_NINT IRQ_GPIO(GPIO_PRDY) + +/* MMC socket */ +#define GPIO_MMC_DET 12 +#define TRIZEPS4_MMC_IRQ IRQ_GPIO(GPIO_MMC_DET) + +/* DOC NAND chip */ +#define GPIO_DOC_LOCK 94 +#define GPIO_DOC_IRQ 93 +#define TRIZEPS4_DOC_IRQ IRQ_GPIO(GPIO_DOC_IRQ) + +/* SPI interface */ +#define GPIO_SPI 53 +#define TRIZEPS4_SPI_IRQ IRQ_GPIO(GPIO_SPI) + +/* LEDS using tx2 / rx2 */ +#define GPIO_SYS_BUSY_LED 46 +#define GPIO_HEARTBEAT_LED 47 + +/* Off-module PIC on ConXS board */ +#define GPIO_PIC 0 +#define TRIZEPS4_PIC_IRQ IRQ_GPIO(GPIO_PIC) + +#ifdef CONFIG_MACH_TRIZEPS_CONXS +/* for CONXS base board define these registers */ +#define CFSR_P2V(x) ((x) - TRIZEPS4_CFSR_PHYS + TRIZEPS4_CFSR_VIRT) +#define CFSR_V2P(x) ((x) - TRIZEPS4_CFSR_VIRT + TRIZEPS4_CFSR_PHYS) + +#define BCR_P2V(x) ((x) - TRIZEPS4_BOCR_PHYS + TRIZEPS4_BOCR_VIRT) +#define BCR_V2P(x) ((x) - TRIZEPS4_BOCR_VIRT + TRIZEPS4_BOCR_PHYS) + +#define DCR_P2V(x) ((x) - TRIZEPS4_DICR_PHYS + TRIZEPS4_DICR_VIRT) +#define DCR_V2P(x) ((x) - TRIZEPS4_DICR_VIRT + TRIZEPS4_DICR_PHYS) + +#define IRCR_P2V(x) ((x) - TRIZEPS4_IRCR_PHYS + TRIZEPS4_IRCR_VIRT) +#define IRCR_V2P(x) ((x) - TRIZEPS4_IRCR_VIRT + TRIZEPS4_IRCR_PHYS) + +#ifndef __ASSEMBLY__ +static inline unsigned short CFSR_readw(void) +{ + /* [Compact Flash Status Register] is read only */ + return *((unsigned short *)CFSR_P2V(0x0C000000)); +} +static inline void BCR_writew(unsigned short value) +{ + /* [Board Control Regsiter] is write only */ + *((unsigned short *)BCR_P2V(0x0E000000)) = value; +} +static inline void DCR_writew(unsigned short value) +{ + /* [Display Control Register] is write only */ + *((unsigned short *)DCR_P2V(0x0E000000)) = value; +} +static inline void IRCR_writew(unsigned short value) +{ + /* [InfraRed data Control Register] is write only */ + *((unsigned short *)IRCR_P2V(0x0E000000)) = value; +} +#else +#define ConXS_CFSR CFSR_P2V(0x0C000000) +#define ConXS_BCR BCR_P2V(0x0E000000) +#define ConXS_DCR DCR_P2V(0x0F800000) +#define ConXS_IRCR IRCR_P2V(0x0F800000) +#endif +#else +/* for whatever baseboard define function registers */ +static inline unsigned short CFSR_readw(void) +{ + return 0; +} +static inline void BCR_writew(unsigned short value) +{ + ; +} +static inline void DCR_writew(unsigned short value) +{ + ; +} +static inline void IRCR_writew(unsigned short value) +{ + ; +} +#endif /* CONFIG_MACH_TRIZEPS_CONXS */ + +#define ConXS_CFSR_BVD_MASK 0x0003 +#define ConXS_CFSR_BVD1 (1 << 0) +#define ConXS_CFSR_BVD2 (1 << 1) +#define ConXS_CFSR_VS_MASK 0x000C +#define ConXS_CFSR_VS1 (1 << 2) +#define ConXS_CFSR_VS2 (1 << 3) +#define ConXS_CFSR_VS_5V (0x3 << 2) +#define ConXS_CFSR_VS_3V3 0x0 + +#define ConXS_BCR_S0_POW_EN0 (1 << 0) +#define ConXS_BCR_S0_POW_EN1 (1 << 1) +#define ConXS_BCR_L_DISP (1 << 4) +#define ConXS_BCR_CF_BUF_EN (1 << 5) +#define ConXS_BCR_CF_RESET (1 << 7) +#define ConXS_BCR_S0_VCC_3V3 0x1 +#define ConXS_BCR_S0_VCC_5V0 0x2 +#define ConXS_BCR_S0_VPP_12V 0x4 +#define ConXS_BCR_S0_VPP_3V3 0x8 + +#define ConXS_IRCR_MODE (1 << 0) +#define ConXS_IRCR_SD (1 << 1) + +#endif /* _TRIPEPS4_H_ */ diff --git a/arch/arm/mach-pxa/include/mach/udc.h b/arch/arm/mach-pxa/include/mach/udc.h new file mode 100644 index 00000000000..2f82332e81a --- /dev/null +++ b/arch/arm/mach-pxa/include/mach/udc.h @@ -0,0 +1,8 @@ +/* + * arch/arm/mach-pxa/include/mach/udc.h + * + */ +#include <asm/mach/udc_pxa2xx.h> + +extern void pxa_set_udc_info(struct pxa2xx_udc_mach_info *info); + diff --git a/arch/arm/mach-pxa/include/mach/uncompress.h b/arch/arm/mach-pxa/include/mach/uncompress.h new file mode 100644 index 00000000000..21e3e890af9 --- /dev/null +++ b/arch/arm/mach-pxa/include/mach/uncompress.h @@ -0,0 +1,45 @@ +/* + * arch/arm/mach-pxa/include/mach/uncompress.h + * + * Author: Nicolas Pitre + * Copyright: (C) 2001 MontaVista Software Inc. + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ + +#include <linux/serial_reg.h> +#include <mach/pxa-regs.h> +#include <asm/mach-types.h> + +#define __REG(x) ((volatile unsigned long *)x) + +static volatile unsigned long *UART = FFUART; + +static inline void putc(char c) +{ + if (!(UART[UART_IER] & IER_UUE)) + return; + while (!(UART[UART_LSR] & LSR_TDRQ)) + barrier(); + UART[UART_TX] = c; +} + +/* + * This does not append a newline + */ +static inline void flush(void) +{ +} + +static inline void arch_decomp_setup(void) +{ + if (machine_is_littleton()) + UART = STUART; +} + +/* + * nothing to do + */ +#define arch_decomp_wdog() diff --git a/arch/arm/mach-pxa/include/mach/viper.h b/arch/arm/mach-pxa/include/mach/viper.h new file mode 100644 index 00000000000..10988c270ca --- /dev/null +++ b/arch/arm/mach-pxa/include/mach/viper.h @@ -0,0 +1,96 @@ +/* + * arch/arm/mach-pxa/include/mach/viper.h + * + * Author: Ian Campbell + * Created: Feb 03, 2003 + * Copyright: Arcom Control Systems. + * + * Maintained by Marc Zyngier <maz@misterjones.org> + * <marc.zyngier@altran.com> + * + * Created based on lubbock.h: + * Author: Nicolas Pitre + * Created: Jun 15, 2001 + * Copyright: MontaVista Software Inc. + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ + +#ifndef ARCH_VIPER_H +#define ARCH_VIPER_H + +#define VIPER_BOOT_PHYS PXA_CS0_PHYS +#define VIPER_FLASH_PHYS PXA_CS1_PHYS +#define VIPER_ETH_PHYS PXA_CS2_PHYS +#define VIPER_USB_PHYS PXA_CS3_PHYS +#define VIPER_ETH_DATA_PHYS PXA_CS4_PHYS +#define VIPER_CPLD_PHYS PXA_CS5_PHYS + +#define VIPER_CPLD_BASE (0xf0000000) +#define VIPER_PC104IO_BASE (0xf1000000) +#define VIPER_USB_BASE (0xf1800000) + +#define VIPER_ETH_GPIO (0) +#define VIPER_CPLD_GPIO (1) +#define VIPER_USB_GPIO (2) +#define VIPER_UARTA_GPIO (4) +#define VIPER_UARTB_GPIO (3) +#define VIPER_CF_CD_GPIO (32) +#define VIPER_CF_RDY_GPIO (8) +#define VIPER_BCKLIGHT_EN_GPIO (9) +#define VIPER_LCD_EN_GPIO (10) +#define VIPER_PSU_DATA_GPIO (6) +#define VIPER_PSU_CLK_GPIO (11) +#define VIPER_UART_SHDN_GPIO (12) +#define VIPER_BRIGHTNESS_GPIO (16) +#define VIPER_PSU_nCS_LD_GPIO (19) +#define VIPER_UPS_GPIO (20) +#define VIPER_CF_POWER_GPIO (82) +#define VIPER_TPM_I2C_SDA_GPIO (26) +#define VIPER_TPM_I2C_SCL_GPIO (27) +#define VIPER_RTC_I2C_SDA_GPIO (83) +#define VIPER_RTC_I2C_SCL_GPIO (84) + +#define VIPER_CPLD_P2V(x) ((x) - VIPER_CPLD_PHYS + VIPER_CPLD_BASE) +#define VIPER_CPLD_V2P(x) ((x) - VIPER_CPLD_BASE + VIPER_CPLD_PHYS) + +#ifndef __ASSEMBLY__ +# define __VIPER_CPLD_REG(x) (*((volatile u16 *)VIPER_CPLD_P2V(x))) +#endif + +/* board level registers in the CPLD: (offsets from CPLD_BASE) ... */ + +/* ... Physical addresses */ +#define _VIPER_LO_IRQ_STATUS (VIPER_CPLD_PHYS + 0x100000) +#define _VIPER_ICR_PHYS (VIPER_CPLD_PHYS + 0x100002) +#define _VIPER_HI_IRQ_STATUS (VIPER_CPLD_PHYS + 0x100004) +#define _VIPER_VERSION_PHYS (VIPER_CPLD_PHYS + 0x100006) +#define VIPER_UARTA_PHYS (VIPER_CPLD_PHYS + 0x300010) +#define VIPER_UARTB_PHYS (VIPER_CPLD_PHYS + 0x300000) +#define _VIPER_SRAM_BASE (VIPER_CPLD_PHYS + 0x800000) + +/* ... Virtual addresses */ +#define VIPER_LO_IRQ_STATUS __VIPER_CPLD_REG(_VIPER_LO_IRQ_STATUS) +#define VIPER_HI_IRQ_STATUS __VIPER_CPLD_REG(_VIPER_HI_IRQ_STATUS) +#define VIPER_VERSION __VIPER_CPLD_REG(_VIPER_VERSION_PHYS) +#define VIPER_ICR __VIPER_CPLD_REG(_VIPER_ICR_PHYS) + +/* Decode VIPER_VERSION register */ +#define VIPER_CPLD_REVISION(x) (((x) >> 5) & 0x7) +#define VIPER_BOARD_VERSION(x) (((x) >> 3) & 0x3) +#define VIPER_BOARD_ISSUE(x) (((x) >> 0) & 0x7) + +/* Interrupt and Configuration Register (VIPER_ICR) */ +/* This is a write only register. Only CF_RST is used under Linux */ + +extern void viper_cf_rst(int state); + +#define VIPER_ICR_RETRIG (1 << 0) +#define VIPER_ICR_AUTO_CLR (1 << 1) +#define VIPER_ICR_R_DIS (1 << 2) +#define VIPER_ICR_CF_RST (1 << 3) + +#endif + diff --git a/arch/arm/mach-pxa/include/mach/vmalloc.h b/arch/arm/mach-pxa/include/mach/vmalloc.h new file mode 100644 index 00000000000..e90c5eeb81d --- /dev/null +++ b/arch/arm/mach-pxa/include/mach/vmalloc.h @@ -0,0 +1,11 @@ +/* + * arch/arm/mach-pxa/include/mach/vmalloc.h + * + * Author: Nicolas Pitre + * Copyright: (C) 2001 MontaVista Software Inc. + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ +#define VMALLOC_END (0xe8000000) diff --git a/arch/arm/mach-pxa/include/mach/zylonite.h b/arch/arm/mach-pxa/include/mach/zylonite.h new file mode 100644 index 00000000000..0d35ca04731 --- /dev/null +++ b/arch/arm/mach-pxa/include/mach/zylonite.h @@ -0,0 +1,47 @@ +#ifndef __ASM_ARCH_ZYLONITE_H +#define __ASM_ARCH_ZYLONITE_H + +#define ZYLONITE_ETH_PHYS 0x14000000 + +#define EXT_GPIO(x) (128 + (x)) + +/* the following variables are processor specific and initialized + * by the corresponding zylonite_pxa3xx_init() + */ +struct platform_mmc_slot { + int gpio_cd; + int gpio_wp; +}; + +extern struct platform_mmc_slot zylonite_mmc_slot[]; + +extern int gpio_eth_irq; +extern int gpio_debug_led1; +extern int gpio_debug_led2; + +extern int wm9713_irq; + +extern int lcd_id; +extern int lcd_orientation; + +#ifdef CONFIG_CPU_PXA300 +extern void zylonite_pxa300_init(void); +#else +static inline void zylonite_pxa300_init(void) +{ + if (cpu_is_pxa300() || cpu_is_pxa310()) + panic("%s: PXA300/PXA310 not supported\n", __FUNCTION__); +} +#endif + +#ifdef CONFIG_CPU_PXA320 +extern void zylonite_pxa320_init(void); +#else +static inline void zylonite_pxa320_init(void) +{ + if (cpu_is_pxa320()) + panic("%s: PXA320 not supported\n", __FUNCTION__); +} +#endif + +#endif /* __ASM_ARCH_ZYLONITE_H */ diff --git a/arch/arm/mach-pxa/irq.c b/arch/arm/mach-pxa/irq.c index a9a0c3fab15..fa69c3a6a38 100644 --- a/arch/arm/mach-pxa/irq.c +++ b/arch/arm/mach-pxa/irq.c @@ -17,11 +17,10 @@ #include <linux/interrupt.h> #include <linux/sysdev.h> -#include <asm/hardware.h> +#include <mach/hardware.h> #include <asm/irq.h> #include <asm/mach/irq.h> -#include <asm/arch/pxa-regs.h> -#include <asm/arch/pxa2xx-gpio.h> +#include <mach/pxa-regs.h> #include "generic.h" @@ -58,7 +57,7 @@ void __init pxa_init_irq(int irq_nr, set_wake_t fn) pxa_internal_irq_nr = irq_nr; - for (irq = 0; irq < irq_nr; irq += 32) { + for (irq = PXA_IRQ(0); irq < PXA_IRQ(irq_nr); irq += 32) { _ICMR(irq) = 0; /* disable all IRQs */ _ICLR(irq) = 0; /* all IRQs are IRQ, not FIQ */ } diff --git a/arch/arm/mach-pxa/leds-idp.c b/arch/arm/mach-pxa/leds-idp.c index 38aa9270540..18b20d46941 100644 --- a/arch/arm/mach-pxa/leds-idp.c +++ b/arch/arm/mach-pxa/leds-idp.c @@ -14,12 +14,12 @@ #include <linux/init.h> -#include <asm/hardware.h> +#include <mach/hardware.h> #include <asm/leds.h> #include <asm/system.h> -#include <asm/arch/pxa-regs.h> -#include <asm/arch/idp.h> +#include <mach/pxa-regs.h> +#include <mach/idp.h> #include "leds.h" diff --git a/arch/arm/mach-pxa/leds-lubbock.c b/arch/arm/mach-pxa/leds-lubbock.c index afbc6698e27..1a258029c33 100644 --- a/arch/arm/mach-pxa/leds-lubbock.c +++ b/arch/arm/mach-pxa/leds-lubbock.c @@ -13,11 +13,11 @@ #include <linux/init.h> -#include <asm/hardware.h> +#include <mach/hardware.h> #include <asm/leds.h> #include <asm/system.h> -#include <asm/arch/pxa-regs.h> -#include <asm/arch/lubbock.h> +#include <mach/pxa-regs.h> +#include <mach/lubbock.h> #include "leds.h" diff --git a/arch/arm/mach-pxa/leds-mainstone.c b/arch/arm/mach-pxa/leds-mainstone.c index 065293eb0d8..95e06b84963 100644 --- a/arch/arm/mach-pxa/leds-mainstone.c +++ b/arch/arm/mach-pxa/leds-mainstone.c @@ -12,12 +12,12 @@ #include <linux/init.h> -#include <asm/hardware.h> +#include <mach/hardware.h> #include <asm/leds.h> #include <asm/system.h> -#include <asm/arch/pxa-regs.h> -#include <asm/arch/mainstone.h> +#include <mach/pxa-regs.h> +#include <mach/mainstone.h> #include "leds.h" diff --git a/arch/arm/mach-pxa/leds-trizeps4.c b/arch/arm/mach-pxa/leds-trizeps4.c deleted file mode 100644 index 21880daabaf..00000000000 --- a/arch/arm/mach-pxa/leds-trizeps4.c +++ /dev/null @@ -1,134 +0,0 @@ -/* - * linux/arch/arm/mach-pxa/leds-trizeps4.c - * - * Author: Jürgen Schindele - * Created: 20 02, 2006 - * Copyright: Jürgen Schindele - * - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License version 2 as - * published by the Free Software Foundation. - */ - -#include <linux/init.h> - -#include <asm/hardware.h> -#include <asm/system.h> -#include <asm/types.h> -#include <asm/leds.h> - -#include <asm/arch/pxa-regs.h> -#include <asm/arch/pxa2xx-gpio.h> -#include <asm/arch/trizeps4.h> - -#include "leds.h" - -#define LED_STATE_ENABLED 1 -#define LED_STATE_CLAIMED 2 - -#define SYS_BUSY 0x01 -#define HEARTBEAT 0x02 -#define BLINK 0x04 - -static unsigned int led_state; -static unsigned int hw_led_state; - -void trizeps4_leds_event(led_event_t evt) -{ - unsigned long flags; - - local_irq_save(flags); - - switch (evt) { - case led_start: - hw_led_state = 0; - pxa_gpio_mode( GPIO_SYS_BUSY_LED | GPIO_OUT); /* LED1 */ - pxa_gpio_mode( GPIO_HEARTBEAT_LED | GPIO_OUT); /* LED2 */ - led_state = LED_STATE_ENABLED; - break; - - case led_stop: - led_state &= ~LED_STATE_ENABLED; - break; - - case led_claim: - led_state |= LED_STATE_CLAIMED; - hw_led_state = 0; - break; - - case led_release: - led_state &= ~LED_STATE_CLAIMED; - hw_led_state = 0; - break; - -#ifdef CONFIG_LEDS_TIMER - case led_timer: - hw_led_state ^= HEARTBEAT; - break; -#endif - -#ifdef CONFIG_LEDS_CPU - case led_idle_start: - hw_led_state &= ~SYS_BUSY; - break; - - case led_idle_end: - hw_led_state |= SYS_BUSY; - break; -#endif - - case led_halted: - break; - - case led_green_on: - hw_led_state |= BLINK; - break; - - case led_green_off: - hw_led_state &= ~BLINK; - break; - - case led_amber_on: - break; - - case led_amber_off: - break; - - case led_red_on: - break; - - case led_red_off: - break; - - default: - break; - } - - if (led_state & LED_STATE_ENABLED) { - switch (hw_led_state) { - case 0: - GPSR(GPIO_SYS_BUSY_LED) |= GPIO_bit(GPIO_SYS_BUSY_LED); - GPSR(GPIO_HEARTBEAT_LED) |= GPIO_bit(GPIO_HEARTBEAT_LED); - break; - case 1: - GPCR(GPIO_SYS_BUSY_LED) |= GPIO_bit(GPIO_SYS_BUSY_LED); - GPSR(GPIO_HEARTBEAT_LED) |= GPIO_bit(GPIO_HEARTBEAT_LED); - break; - case 2: - GPSR(GPIO_SYS_BUSY_LED) |= GPIO_bit(GPIO_SYS_BUSY_LED); - GPCR(GPIO_HEARTBEAT_LED) |= GPIO_bit(GPIO_HEARTBEAT_LED); - break; - case 3: - GPCR(GPIO_SYS_BUSY_LED) |= GPIO_bit(GPIO_SYS_BUSY_LED); - GPCR(GPIO_HEARTBEAT_LED) |= GPIO_bit(GPIO_HEARTBEAT_LED); - break; - } - } - else { - /* turn all off */ - GPSR(GPIO_SYS_BUSY_LED) |= GPIO_bit(GPIO_SYS_BUSY_LED); - GPSR(GPIO_HEARTBEAT_LED) |= GPIO_bit(GPIO_HEARTBEAT_LED); - } - - local_irq_restore(flags); -} diff --git a/arch/arm/mach-pxa/leds.c b/arch/arm/mach-pxa/leds.c index e13eb841e48..bbe4d5f6afa 100644 --- a/arch/arm/mach-pxa/leds.c +++ b/arch/arm/mach-pxa/leds.c @@ -24,8 +24,6 @@ pxa_leds_init(void) leds_event = mainstone_leds_event; if (machine_is_pxa_idp()) leds_event = idp_leds_event; - if (machine_is_trizeps4()) - leds_event = trizeps4_leds_event; leds_event(led_start); return 0; diff --git a/arch/arm/mach-pxa/littleton.c b/arch/arm/mach-pxa/littleton.c index 530654474bb..b4d00aba0e3 100644 --- a/arch/arm/mach-pxa/littleton.c +++ b/arch/arm/mach-pxa/littleton.c @@ -20,25 +20,29 @@ #include <linux/delay.h> #include <linux/platform_device.h> #include <linux/clk.h> +#include <linux/spi/spi.h> +#include <linux/smc91x.h> #include <asm/types.h> #include <asm/setup.h> #include <asm/memory.h> #include <asm/mach-types.h> -#include <asm/hardware.h> +#include <mach/hardware.h> #include <asm/irq.h> #include <asm/mach/arch.h> #include <asm/mach/map.h> #include <asm/mach/irq.h> -#include <asm/arch/pxa-regs.h> -#include <asm/arch/mfp-pxa300.h> -#include <asm/arch/gpio.h> -#include <asm/arch/pxafb.h> -#include <asm/arch/ssp.h> -#include <asm/arch/pxa27x_keypad.h> -#include <asm/arch/littleton.h> +#include <mach/pxa-regs.h> +#include <mach/mfp-pxa300.h> +#include <mach/gpio.h> +#include <mach/pxafb.h> +#include <mach/ssp.h> +#include <mach/pxa2xx_spi.h> +#include <mach/pxa27x_keypad.h> +#include <mach/pxa3xx_nand.h> +#include <mach/littleton.h> #include "generic.h" @@ -70,8 +74,8 @@ static mfp_cfg_t littleton_mfp_cfg[] __initdata = { /* SSP2 */ GPIO25_SSP2_SCLK, - GPIO17_SSP2_FRM, GPIO27_SSP2_TXD, + GPIO17_GPIO, /* SFRM as chip-select */ /* Debug Ethernet */ GPIO90_GPIO, @@ -101,172 +105,26 @@ static struct resource smc91x_resources[] = { [1] = { .start = IRQ_GPIO(mfp_to_gpio(MFP_PIN_GPIO90)), .end = IRQ_GPIO(mfp_to_gpio(MFP_PIN_GPIO90)), - .flags = IORESOURCE_IRQ | IRQF_TRIGGER_FALLING, + .flags = IORESOURCE_IRQ | IORESOURCE_IRQ_LOWEDGE, } }; +static struct smc91x_platdata littleton_smc91x_info = { + .flags = SMC91X_USE_8BIT | SMC91X_USE_16BIT | + SMC91X_NOWAIT | SMC91X_USE_DMA, +}; + static struct platform_device smc91x_device = { .name = "smc91x", .id = 0, .num_resources = ARRAY_SIZE(smc91x_resources), .resource = smc91x_resources, + .dev = { + .platform_data = &littleton_smc91x_info, + }, }; -#if defined(CONFIG_FB_PXA) || defined(CONFIG_FB_PXA_MODULES) -/* use bit 30, 31 as the indicator of command parameter number */ -#define CMD0(x) ((0x00000000) | ((x) << 9)) -#define CMD1(x, x1) ((0x40000000) | ((x) << 9) | 0x100 | (x1)) -#define CMD2(x, x1, x2) ((0x80000000) | ((x) << 18) | 0x20000 |\ - ((x1) << 9) | 0x100 | (x2)) - -static uint32_t lcd_panel_reset[] = { - CMD0(0x1), /* reset */ - CMD0(0x0), /* nop */ - CMD0(0x0), /* nop */ - CMD0(0x0), /* nop */ -}; - -static uint32_t lcd_panel_on[] = { - CMD0(0x29), /* Display ON */ - CMD2(0xB8, 0xFF, 0xF9), /* Output Control */ - CMD0(0x11), /* Sleep out */ - CMD1(0xB0, 0x16), /* Wake */ -}; - -static uint32_t lcd_panel_off[] = { - CMD0(0x28), /* Display OFF */ - CMD2(0xB8, 0x80, 0x02), /* Output Control */ - CMD0(0x10), /* Sleep in */ - CMD1(0xB0, 0x00), /* Deep stand by in */ -}; - -static uint32_t lcd_vga_pass_through[] = { - CMD1(0xB0, 0x16), - CMD1(0xBC, 0x80), - CMD1(0xE1, 0x00), - CMD1(0x36, 0x50), - CMD1(0x3B, 0x00), -}; - -static uint32_t lcd_qvga_pass_through[] = { - CMD1(0xB0, 0x16), - CMD1(0xBC, 0x81), - CMD1(0xE1, 0x00), - CMD1(0x36, 0x50), - CMD1(0x3B, 0x22), -}; - -static uint32_t lcd_vga_transfer[] = { - CMD1(0xcf, 0x02), /* Blanking period control (1) */ - CMD2(0xd0, 0x08, 0x04), /* Blanking period control (2) */ - CMD1(0xd1, 0x01), /* CKV timing control on/off */ - CMD2(0xd2, 0x14, 0x00), /* CKV 1,2 timing control */ - CMD2(0xd3, 0x1a, 0x0f), /* OEV timing control */ - CMD2(0xd4, 0x1f, 0xaf), /* ASW timing control (1) */ - CMD1(0xd5, 0x14), /* ASW timing control (2) */ - CMD0(0x21), /* Invert for normally black display */ - CMD0(0x29), /* Display on */ -}; - -static uint32_t lcd_qvga_transfer[] = { - CMD1(0xd6, 0x02), /* Blanking period control (1) */ - CMD2(0xd7, 0x08, 0x04), /* Blanking period control (2) */ - CMD1(0xd8, 0x01), /* CKV timing control on/off */ - CMD2(0xd9, 0x00, 0x08), /* CKV 1,2 timing control */ - CMD2(0xde, 0x05, 0x0a), /* OEV timing control */ - CMD2(0xdf, 0x0a, 0x19), /* ASW timing control (1) */ - CMD1(0xe0, 0x0a), /* ASW timing control (2) */ - CMD0(0x21), /* Invert for normally black display */ - CMD0(0x29), /* Display on */ -}; - -static uint32_t lcd_panel_config[] = { - CMD2(0xb8, 0xff, 0xf9), /* Output control */ - CMD0(0x11), /* sleep out */ - CMD1(0xba, 0x01), /* Display mode (1) */ - CMD1(0xbb, 0x00), /* Display mode (2) */ - CMD1(0x3a, 0x60), /* Display mode 18-bit RGB */ - CMD1(0xbf, 0x10), /* Drive system change control */ - CMD1(0xb1, 0x56), /* Booster operation setup */ - CMD1(0xb2, 0x33), /* Booster mode setup */ - CMD1(0xb3, 0x11), /* Booster frequency setup */ - CMD1(0xb4, 0x02), /* Op amp/system clock */ - CMD1(0xb5, 0x35), /* VCS voltage */ - CMD1(0xb6, 0x40), /* VCOM voltage */ - CMD1(0xb7, 0x03), /* External display signal */ - CMD1(0xbd, 0x00), /* ASW slew rate */ - CMD1(0xbe, 0x00), /* Dummy data for QuadData operation */ - CMD1(0xc0, 0x11), /* Sleep out FR count (A) */ - CMD1(0xc1, 0x11), /* Sleep out FR count (B) */ - CMD1(0xc2, 0x11), /* Sleep out FR count (C) */ - CMD2(0xc3, 0x20, 0x40), /* Sleep out FR count (D) */ - CMD2(0xc4, 0x60, 0xc0), /* Sleep out FR count (E) */ - CMD2(0xc5, 0x10, 0x20), /* Sleep out FR count (F) */ - CMD1(0xc6, 0xc0), /* Sleep out FR count (G) */ - CMD2(0xc7, 0x33, 0x43), /* Gamma 1 fine tuning (1) */ - CMD1(0xc8, 0x44), /* Gamma 1 fine tuning (2) */ - CMD1(0xc9, 0x33), /* Gamma 1 inclination adjustment */ - CMD1(0xca, 0x00), /* Gamma 1 blue offset adjustment */ - CMD2(0xec, 0x01, 0xf0), /* Horizontal clock cycles */ -}; - -static void ssp_reconfig(struct ssp_dev *dev, int nparam) -{ - static int last_nparam = -1; - - /* check if it is necessary to re-config SSP */ - if (nparam == last_nparam) - return; - - ssp_disable(dev); - ssp_config(dev, (nparam == 2) ? 0x0010058a : 0x00100581, 0x18, 0, 0); - - last_nparam = nparam; -} - -static void ssp_send_cmd(uint32_t *cmd, int num) -{ - static int ssp_initialized; - static struct ssp_dev ssp2; - - int i; - - if (!ssp_initialized) { - ssp_init(&ssp2, 2, SSP_NO_IRQ); - ssp_initialized = 1; - } - - clk_enable(ssp2.ssp->clk); - for (i = 0; i < num; i++, cmd++) { - ssp_reconfig(&ssp2, (*cmd >> 30) & 0x3); - ssp_write_word(&ssp2, *cmd & 0x3fffffff); - - /* FIXME: ssp_flush() is mandatory here to work */ - ssp_flush(&ssp2); - } - clk_disable(ssp2.ssp->clk); -} - -static void littleton_lcd_power(int on, struct fb_var_screeninfo *var) -{ - if (on) { - ssp_send_cmd(ARRAY_AND_SIZE(lcd_panel_on)); - ssp_send_cmd(ARRAY_AND_SIZE(lcd_panel_reset)); - if (var->xres > 240) { - /* VGA */ - ssp_send_cmd(ARRAY_AND_SIZE(lcd_vga_pass_through)); - ssp_send_cmd(ARRAY_AND_SIZE(lcd_panel_config)); - ssp_send_cmd(ARRAY_AND_SIZE(lcd_vga_transfer)); - } else { - /* QVGA */ - ssp_send_cmd(ARRAY_AND_SIZE(lcd_qvga_pass_through)); - ssp_send_cmd(ARRAY_AND_SIZE(lcd_panel_config)); - ssp_send_cmd(ARRAY_AND_SIZE(lcd_qvga_transfer)); - } - } else - ssp_send_cmd(ARRAY_AND_SIZE(lcd_panel_off)); -} - +#if defined(CONFIG_FB_PXA) || defined(CONFIG_FB_PXA_MODULE) static struct pxafb_mode_info tpo_tdo24mtea1_modes[] = { [0] = { /* VGA */ @@ -302,7 +160,6 @@ static struct pxafb_mach_info littleton_lcd_info = { .modes = tpo_tdo24mtea1_modes, .num_modes = 2, .lcd_conn = LCD_COLOR_TFT_16BPP, - .pxafb_lcd_power = littleton_lcd_power, }; static void littleton_init_lcd(void) @@ -311,9 +168,54 @@ static void littleton_init_lcd(void) } #else static inline void littleton_init_lcd(void) {}; -#endif /* CONFIG_FB_PXA || CONFIG_FB_PXA_MODULES */ +#endif /* CONFIG_FB_PXA || CONFIG_FB_PXA_MODULE */ + +#if defined(CONFIG_SPI_PXA2XX) || defined(CONFIG_SPI_PXA2XX_MODULE) +static struct pxa2xx_spi_master littleton_spi_info = { + .num_chipselect = 1, +}; + +static void littleton_tdo24m_cs(u32 cmd) +{ + gpio_set_value(LITTLETON_GPIO_LCD_CS, !(cmd == PXA2XX_CS_ASSERT)); +} + +static struct pxa2xx_spi_chip littleton_tdo24m_chip = { + .rx_threshold = 1, + .tx_threshold = 1, + .cs_control = littleton_tdo24m_cs, +}; -#if defined(CONFIG_KEYBOARD_PXA27x) || defined(CONFIG_KEYBOARD_PXA27x_MODULES) +static struct spi_board_info littleton_spi_devices[] __initdata = { + { + .modalias = "tdo24m", + .max_speed_hz = 1000000, + .bus_num = 2, + .chip_select = 0, + .controller_data= &littleton_tdo24m_chip, + }, +}; + +static void __init littleton_init_spi(void) +{ + int err; + + err = gpio_request(LITTLETON_GPIO_LCD_CS, "LCD_CS"); + if (err) { + pr_warning("failed to request GPIO for LCS CS\n"); + return; + } + + gpio_direction_output(LITTLETON_GPIO_LCD_CS, 1); + + pxa2xx_set_spi_info(2, &littleton_spi_info); + spi_register_board_info(ARRAY_AND_SIZE(littleton_spi_devices)); +} +#else +static inline void littleton_init_spi(void) {} +#endif + +#if defined(CONFIG_KEYBOARD_PXA27x) || defined(CONFIG_KEYBOARD_PXA27x_MODULE) static unsigned int littleton_matrix_key_map[] = { /* KEY(row, col, key_code) */ KEY(1, 3, KEY_0), KEY(0, 0, KEY_1), KEY(1, 0, KEY_2), KEY(2, 0, KEY_3), @@ -361,6 +263,57 @@ static void __init littleton_init_keypad(void) static inline void littleton_init_keypad(void) {} #endif +#if defined(CONFIG_MTD_NAND_PXA3xx) || defined(CONFIG_MTD_NAND_PXA3xx_MODULE) +static struct mtd_partition littleton_nand_partitions[] = { + [0] = { + .name = "Bootloader", + .offset = 0, + .size = 0x060000, + .mask_flags = MTD_WRITEABLE, /* force read-only */ + }, + [1] = { + .name = "Kernel", + .offset = 0x060000, + .size = 0x200000, + .mask_flags = MTD_WRITEABLE, /* force read-only */ + }, + [2] = { + .name = "Filesystem", + .offset = 0x0260000, + .size = 0x3000000, /* 48M - rootfs */ + }, + [3] = { + .name = "MassStorage", + .offset = 0x3260000, + .size = 0x3d40000, + }, + [4] = { + .name = "BBT", + .offset = 0x6FA0000, + .size = 0x80000, + .mask_flags = MTD_WRITEABLE, /* force read-only */ + }, + /* NOTE: we reserve some blocks at the end of the NAND flash for + * bad block management, and the max number of relocation blocks + * differs on different platforms. Please take care with it when + * defining the partition table. + */ +}; + +static struct pxa3xx_nand_platform_data littleton_nand_info = { + .enable_arbiter = 1, + .parts = littleton_nand_partitions, + .nr_parts = ARRAY_SIZE(littleton_nand_partitions), +}; + +static void __init littleton_init_nand(void) +{ + pxa3xx_set_nand_info(&littleton_nand_info); +} +#else +static inline void littleton_init_nand(void) {} +#endif /* CONFIG_MTD_NAND_PXA3xx || CONFIG_MTD_NAND_PXA3xx_MODULE */ + static void __init littleton_init(void) { /* initialize MFP configurations */ @@ -372,8 +325,10 @@ static void __init littleton_init(void) */ platform_device_register(&smc91x_device); + littleton_init_spi(); littleton_init_lcd(); littleton_init_keypad(); + littleton_init_nand(); } MACHINE_START(LITTLETON, "Marvell Form Factor Development Platform (aka Littleton)") diff --git a/arch/arm/mach-pxa/lpd270.c b/arch/arm/mach-pxa/lpd270.c index a20e4b1649d..de3f67daaac 100644 --- a/arch/arm/mach-pxa/lpd270.c +++ b/arch/arm/mach-pxa/lpd270.c @@ -23,12 +23,13 @@ #include <linux/ioport.h> #include <linux/mtd/mtd.h> #include <linux/mtd/partitions.h> +#include <linux/pwm_backlight.h> #include <asm/types.h> #include <asm/setup.h> #include <asm/memory.h> #include <asm/mach-types.h> -#include <asm/hardware.h> +#include <mach/hardware.h> #include <asm/irq.h> #include <asm/sizes.h> @@ -37,19 +38,56 @@ #include <asm/mach/irq.h> #include <asm/mach/flash.h> -#include <asm/arch/pxa-regs.h> -#include <asm/arch/pxa2xx-regs.h> -#include <asm/arch/pxa2xx-gpio.h> -#include <asm/arch/lpd270.h> -#include <asm/arch/audio.h> -#include <asm/arch/pxafb.h> -#include <asm/arch/mmc.h> -#include <asm/arch/irda.h> -#include <asm/arch/ohci.h> +#include <mach/pxa-regs.h> +#include <mach/pxa2xx-regs.h> +#include <mach/mfp-pxa27x.h> +#include <mach/lpd270.h> +#include <mach/audio.h> +#include <mach/pxafb.h> +#include <mach/mmc.h> +#include <mach/irda.h> +#include <mach/ohci.h> #include "generic.h" #include "devices.h" +static unsigned long lpd270_pin_config[] __initdata = { + /* Chip Selects */ + GPIO15_nCS_1, /* Mainboard Flash */ + GPIO78_nCS_2, /* CPLD + Ethernet */ + + /* LCD - 16bpp Active TFT */ + GPIO58_LCD_LDD_0, + GPIO59_LCD_LDD_1, + GPIO60_LCD_LDD_2, + GPIO61_LCD_LDD_3, + GPIO62_LCD_LDD_4, + GPIO63_LCD_LDD_5, + GPIO64_LCD_LDD_6, + GPIO65_LCD_LDD_7, + GPIO66_LCD_LDD_8, + GPIO67_LCD_LDD_9, + GPIO68_LCD_LDD_10, + GPIO69_LCD_LDD_11, + GPIO70_LCD_LDD_12, + GPIO71_LCD_LDD_13, + GPIO72_LCD_LDD_14, + GPIO73_LCD_LDD_15, + GPIO74_LCD_FCLK, + GPIO75_LCD_LCLK, + GPIO76_LCD_PCLK, + GPIO77_LCD_BIAS, + GPIO16_PWM0_OUT, /* Backlight */ + + /* USB Host */ + GPIO88_USBH1_PWR, + GPIO89_USBH1_PEN, + + /* AC97 */ + GPIO45_AC97_SYSCLK, + + GPIO1_GPIO | WAKEUP_ON_EDGE_BOTH, +}; static unsigned int lpd270_irq_enabled; @@ -87,8 +125,7 @@ static void lpd270_irq_handler(unsigned int irq, struct irq_desc *desc) GEDR(0) = GPIO_bit(0); /* clear useless edge notification */ if (likely(pending)) { irq = LPD270_IRQ(0) + __ffs(pending); - desc = irq_desc + irq; - desc_handle_irq(irq, desc); + generic_handle_irq(irq); pending = __raw_readw(LPD270_INT_STATUS) & lpd270_irq_enabled; @@ -112,7 +149,7 @@ static void __init lpd270_init_irq(void) set_irq_flags(irq, IRQF_VALID | IRQF_PROBE); } set_irq_chained_handler(IRQ_GPIO(0), lpd270_irq_handler); - set_irq_type(IRQ_GPIO(0), IRQT_FALLING); + set_irq_type(IRQ_GPIO(0), IRQ_TYPE_EDGE_FALLING); } @@ -134,9 +171,12 @@ static struct sys_device lpd270_irq_device = { static int __init lpd270_irq_device_init(void) { - int ret = sysdev_class_register(&lpd270_irq_sysclass); - if (ret == 0) - ret = sysdev_register(&lpd270_irq_device); + int ret = -ENODEV; + if (machine_is_logicpd_pxa270()) { + ret = sysdev_class_register(&lpd270_irq_sysclass); + if (ret == 0) + ret = sysdev_register(&lpd270_irq_device); + } return ret; } @@ -164,11 +204,6 @@ static struct platform_device smc91x_device = { .resource = smc91x_resources, }; -static struct platform_device lpd270_audio_device = { - .name = "pxa2xx-ac97", - .id = -1, -}; - static struct resource lpd270_flash_resources[] = { [0] = { .start = PXA_CS0_PHYS, @@ -233,21 +268,20 @@ static struct platform_device lpd270_flash_device[2] = { }, }; -static void lpd270_backlight_power(int on) -{ - if (on) { - pxa_gpio_mode(GPIO16_PWM0_MD); - pxa_set_cken(CKEN_PWM0, 1); - PWM_CTRL0 = 0; - PWM_PWDUTY0 = 0x3ff; - PWM_PERVAL0 = 0x3ff; - } else { - PWM_CTRL0 = 0; - PWM_PWDUTY0 = 0x0; - PWM_PERVAL0 = 0x3FF; - pxa_set_cken(CKEN_PWM0, 0); - } -} +static struct platform_pwm_backlight_data lpd270_backlight_data = { + .pwm_id = 0, + .max_brightness = 1, + .dft_brightness = 1, + .pwm_period_ns = 78770, +}; + +static struct platform_device lpd270_backlight_device = { + .name = "pwm-backlight", + .dev = { + .parent = &pxa27x_device_pwm0.dev, + .platform_data = &lpd270_backlight_data, + }, +}; /* 5.7" TFT QVGA (LoLo display number 1) */ static struct pxafb_mode_info sharp_lq057q3dc02_mode = { @@ -267,9 +301,8 @@ static struct pxafb_mode_info sharp_lq057q3dc02_mode = { static struct pxafb_mach_info sharp_lq057q3dc02 = { .modes = &sharp_lq057q3dc02_mode, .num_modes = 1, - .lccr0 = 0x07800080, - .lccr3 = 0x00400000, - .pxafb_backlight_power = lpd270_backlight_power, + .lcd_conn = LCD_COLOR_TFT_16BPP | LCD_PCLK_EDGE_FALL | + LCD_ALTERNATE_MAPPING, }; /* 12.1" TFT SVGA (LoLo display number 2) */ @@ -290,9 +323,8 @@ static struct pxafb_mode_info sharp_lq121s1dg31_mode = { static struct pxafb_mach_info sharp_lq121s1dg31 = { .modes = &sharp_lq121s1dg31_mode, .num_modes = 1, - .lccr0 = 0x07800080, - .lccr3 = 0x00400000, - .pxafb_backlight_power = lpd270_backlight_power, + .lcd_conn = LCD_COLOR_TFT_16BPP | LCD_PCLK_EDGE_FALL | + LCD_ALTERNATE_MAPPING, }; /* 3.6" TFT QVGA (LoLo display number 3) */ @@ -313,9 +345,8 @@ static struct pxafb_mode_info sharp_lq036q1da01_mode = { static struct pxafb_mach_info sharp_lq036q1da01 = { .modes = &sharp_lq036q1da01_mode, .num_modes = 1, - .lccr0 = 0x07800080, - .lccr3 = 0x00400000, - .pxafb_backlight_power = lpd270_backlight_power, + .lcd_conn = LCD_COLOR_TFT_16BPP | LCD_PCLK_EDGE_FALL | + LCD_ALTERNATE_MAPPING, }; /* 6.4" TFT VGA (LoLo display number 5) */ @@ -336,9 +367,8 @@ static struct pxafb_mode_info sharp_lq64d343_mode = { static struct pxafb_mach_info sharp_lq64d343 = { .modes = &sharp_lq64d343_mode, .num_modes = 1, - .lccr0 = 0x07800080, - .lccr3 = 0x00400000, - .pxafb_backlight_power = lpd270_backlight_power, + .lcd_conn = LCD_COLOR_TFT_16BPP | LCD_PCLK_EDGE_FALL | + LCD_ALTERNATE_MAPPING, }; /* 10.4" TFT VGA (LoLo display number 7) */ @@ -359,9 +389,8 @@ static struct pxafb_mode_info sharp_lq10d368_mode = { static struct pxafb_mach_info sharp_lq10d368 = { .modes = &sharp_lq10d368_mode, .num_modes = 1, - .lccr0 = 0x07800080, - .lccr3 = 0x00400000, - .pxafb_backlight_power = lpd270_backlight_power, + .lcd_conn = LCD_COLOR_TFT_16BPP | LCD_PCLK_EDGE_FALL | + LCD_ALTERNATE_MAPPING, }; /* 3.5" TFT QVGA (LoLo display number 8) */ @@ -382,9 +411,8 @@ static struct pxafb_mode_info sharp_lq035q7db02_20_mode = { static struct pxafb_mach_info sharp_lq035q7db02_20 = { .modes = &sharp_lq035q7db02_20_mode, .num_modes = 1, - .lccr0 = 0x07800080, - .lccr3 = 0x00400000, - .pxafb_backlight_power = lpd270_backlight_power, + .lcd_conn = LCD_COLOR_TFT_16BPP | LCD_PCLK_EDGE_FALL | + LCD_ALTERNATE_MAPPING, }; static struct pxafb_mach_info *lpd270_lcd_to_use; @@ -414,32 +442,20 @@ __setup("lcd=", lpd270_set_lcd); static struct platform_device *platform_devices[] __initdata = { &smc91x_device, - &lpd270_audio_device, + &lpd270_backlight_device, &lpd270_flash_device[0], &lpd270_flash_device[1], }; -static int lpd270_ohci_init(struct device *dev) -{ - /* setup Port1 GPIO pin. */ - pxa_gpio_mode(88 | GPIO_ALT_FN_1_IN); /* USBHPWR1 */ - pxa_gpio_mode(89 | GPIO_ALT_FN_2_OUT); /* USBHPEN1 */ - - /* Set the Power Control Polarity Low and Power Sense - Polarity Low to active low. */ - UHCHR = (UHCHR | UHCHR_PCPL | UHCHR_PSPL) & - ~(UHCHR_SSEP1 | UHCHR_SSEP2 | UHCHR_SSEP3 | UHCHR_SSE); - - return 0; -} - static struct pxaohci_platform_data lpd270_ohci_platform_data = { .port_mode = PMM_PERPORT_MODE, - .init = lpd270_ohci_init, + .flags = ENABLE_PORT_ALL | POWER_CONTROL_LOW | POWER_SENSE_LOW, }; static void __init lpd270_init(void) { + pxa2xx_mfp_config(ARRAY_AND_SIZE(lpd270_pin_config)); + lpd270_flash_data[0].width = (BOOT_DEF & 1) ? 2 : 4; lpd270_flash_data[1].width = 4; @@ -450,13 +466,10 @@ static void __init lpd270_init(void) */ ARB_CNTRL = ARB_CORE_PARK | 0x234; - /* - * On LogicPD PXA270, we route AC97_SYSCLK via GPIO45. - */ - pxa_gpio_mode(GPIO45_SYSCLK_AC97_MD); - platform_add_devices(platform_devices, ARRAY_SIZE(platform_devices)); + pxa_set_ac97_info(NULL); + if (lpd270_lcd_to_use != NULL) set_pxa_fb_info(lpd270_lcd_to_use); @@ -478,15 +491,6 @@ static void __init lpd270_map_io(void) pxa_map_io(); iotable_init(lpd270_io_desc, ARRAY_SIZE(lpd270_io_desc)); - /* initialize sleep mode regs (wake-up sources, etc) */ - PGSR0 = 0x00008800; - PGSR1 = 0x00000002; - PGSR2 = 0x0001FC00; - PGSR3 = 0x00001F81; - PWER = 0xC0000002; - PRER = 0x00000002; - PFER = 0x00000002; - /* for use I SRAM as framebuffer. */ PSLR |= 0x00000F04; PCFR = 0x00000066; diff --git a/arch/arm/mach-pxa/lubbock.c b/arch/arm/mach-pxa/lubbock.c index 7b9bdd0c666..bff704354c1 100644 --- a/arch/arm/mach-pxa/lubbock.c +++ b/arch/arm/mach-pxa/lubbock.c @@ -21,15 +21,16 @@ #include <linux/interrupt.h> #include <linux/mtd/mtd.h> #include <linux/mtd/partitions.h> +#include <linux/smc91x.h> #include <linux/spi/spi.h> #include <linux/spi/ads7846.h> -#include <asm/arch/pxa2xx_spi.h> +#include <mach/pxa2xx_spi.h> #include <asm/setup.h> #include <asm/memory.h> #include <asm/mach-types.h> -#include <asm/hardware.h> +#include <mach/hardware.h> #include <asm/irq.h> #include <asm/sizes.h> @@ -40,27 +41,52 @@ #include <asm/hardware/sa1111.h> -#include <asm/arch/pxa-regs.h> -#include <asm/arch/pxa2xx-regs.h> -#include <asm/arch/mfp-pxa25x.h> -#include <asm/arch/lubbock.h> -#include <asm/arch/udc.h> -#include <asm/arch/irda.h> -#include <asm/arch/pxafb.h> -#include <asm/arch/mmc.h> +#include <mach/pxa-regs.h> +#include <mach/pxa2xx-regs.h> +#include <mach/mfp-pxa25x.h> +#include <mach/audio.h> +#include <mach/lubbock.h> +#include <mach/udc.h> +#include <mach/irda.h> +#include <mach/pxafb.h> +#include <mach/mmc.h> #include "generic.h" +#include "clock.h" #include "devices.h" static unsigned long lubbock_pin_config[] __initdata = { GPIO15_nCS_1, /* CS1 - Flash */ + GPIO78_nCS_2, /* CS2 - Baseboard FGPA */ GPIO79_nCS_3, /* CS3 - SMC ethernet */ + GPIO80_nCS_4, /* CS4 - SA1111 */ /* SSP data pins */ GPIO23_SSP1_SCLK, GPIO25_SSP1_TXD, GPIO26_SSP1_RXD, + /* LCD - 16bpp DSTN */ + GPIO58_LCD_LDD_0, + GPIO59_LCD_LDD_1, + GPIO60_LCD_LDD_2, + GPIO61_LCD_LDD_3, + GPIO62_LCD_LDD_4, + GPIO63_LCD_LDD_5, + GPIO64_LCD_LDD_6, + GPIO65_LCD_LDD_7, + GPIO66_LCD_LDD_8, + GPIO67_LCD_LDD_9, + GPIO68_LCD_LDD_10, + GPIO69_LCD_LDD_11, + GPIO70_LCD_LDD_12, + GPIO71_LCD_LDD_13, + GPIO72_LCD_LDD_14, + GPIO73_LCD_LDD_15, + GPIO74_LCD_FCLK, + GPIO75_LCD_LCLK, + GPIO76_LCD_PCLK, + /* BTUART */ GPIO42_BTUART_RXD, GPIO43_BTUART_TXD, @@ -129,8 +155,7 @@ static void lubbock_irq_handler(unsigned int irq, struct irq_desc *desc) GEDR(0) = GPIO_bit(0); /* clear our parent irq */ if (likely(pending)) { irq = LUBBOCK_IRQ(0) + __ffs(pending); - desc = irq_desc + irq; - desc_handle_irq(irq, desc); + generic_handle_irq(irq); } pending = LUB_IRQ_SET_CLR & lubbock_irq_enabled; } while (pending); @@ -150,7 +175,7 @@ static void __init lubbock_init_irq(void) } set_irq_chained_handler(IRQ_GPIO(0), lubbock_irq_handler); - set_irq_type(IRQ_GPIO(0), IRQT_FALLING); + set_irq_type(IRQ_GPIO(0), IRQ_TYPE_EDGE_FALLING); } #ifdef CONFIG_PM @@ -196,11 +221,6 @@ static struct pxa2xx_udc_mach_info udc_info __initdata = { // no D+ pullup; lubbock can't connect/disconnect in software }; -static struct platform_device lub_audio_device = { - .name = "pxa2xx-ac97", - .id = -1, -}; - static struct resource sa1111_resources[] = { [0] = { .start = 0x10000000, @@ -227,15 +247,7 @@ static struct platform_device sa1111_device = { * for the temperature sensors. */ static struct pxa2xx_spi_master pxa_ssp_master_info = { - .num_chipselect = 0, -}; - -static struct platform_device pxa_ssp = { - .name = "pxa2xx-spi", - .id = 1, - .dev = { - .platform_data = &pxa_ssp_master_info, - }, + .num_chipselect = 1, }; static int lubbock_ads7846_pendown_state(void) @@ -296,11 +308,18 @@ static struct resource smc91x_resources[] = { }, }; +static struct smc91x_platdata lubbock_smc91x_info = { + .flags = SMC91X_USE_16BIT | SMC91X_NOWAIT | SMC91X_IO_SHIFT_2, +}; + static struct platform_device smc91x_device = { .name = "smc91x", .id = -1, .num_resources = ARRAY_SIZE(smc91x_resources), .resource = smc91x_resources, + .dev = { + .platform_data = &lubbock_smc91x_info, + }, }; static struct resource flash_resources[] = { @@ -368,11 +387,9 @@ static struct platform_device lubbock_flash_device[2] = { static struct platform_device *devices[] __initdata = { &sa1111_device, - &lub_audio_device, &smc91x_device, &lubbock_flash_device[0], &lubbock_flash_device[1], - &pxa_ssp, }; static struct pxafb_mode_info sharp_lm8v31_mode = { @@ -476,6 +493,7 @@ static void lubbock_irda_transceiver_mode(struct device *dev, int mode) } else if (mode & IR_FIRMODE) { LUB_MISC_WR |= 1 << 4; } + pxa2xx_transceiver_mode(dev, mode); local_irq_restore(flags); } @@ -490,10 +508,12 @@ static void __init lubbock_init(void) pxa2xx_mfp_config(ARRAY_AND_SIZE(lubbock_pin_config)); + clk_add_alias("SA1111_CLK", NULL, "GPIO11_CLK", NULL); pxa_set_udc_info(&udc_info); set_pxa_fb_info(&sharp_lm8v31); pxa_set_mci_info(&lubbock_mci_platform_data); pxa_set_ficp_info(&lubbock_ficp_platform_data); + pxa_set_ac97_info(NULL); lubbock_flash_data[0].width = lubbock_flash_data[1].width = (BOOT_DEF & 1) ? 2 : 4; @@ -505,6 +525,7 @@ static void __init lubbock_init(void) lubbock_flash_data[flashboot].name = "boot-rom"; (void) platform_add_devices(devices, ARRAY_SIZE(devices)); + pxa2xx_set_spi_info(1, &pxa_ssp_master_info); spi_register_board_info(spi_board_info, ARRAY_SIZE(spi_board_info)); } diff --git a/arch/arm/mach-pxa/magician.c b/arch/arm/mach-pxa/magician.c index badba064dc0..519138bc5f8 100644 --- a/arch/arm/mach-pxa/magician.c +++ b/arch/arm/mach-pxa/magician.c @@ -17,31 +17,32 @@ #include <linux/init.h> #include <linux/platform_device.h> #include <linux/delay.h> +#include <linux/gpio.h> #include <linux/gpio_keys.h> #include <linux/input.h> #include <linux/mfd/htc-egpio.h> #include <linux/mfd/htc-pasic3.h> -#include <linux/mtd/mtd.h> -#include <linux/mtd/map.h> #include <linux/mtd/physmap.h> #include <linux/pda_power.h> +#include <linux/pwm_backlight.h> -#include <asm/gpio.h> -#include <asm/hardware.h> +#include <mach/hardware.h> #include <asm/mach-types.h> #include <asm/mach/arch.h> -#include <asm/arch/magician.h> -#include <asm/arch/mfp-pxa27x.h> -#include <asm/arch/pxa-regs.h> -#include <asm/arch/pxafb.h> -#include <asm/arch/i2c.h> -#include <asm/arch/mmc.h> -#include <asm/arch/irda.h> -#include <asm/arch/ohci.h> - +#include <mach/magician.h> +#include <mach/mfp-pxa27x.h> +#include <mach/pxa-regs.h> +#include <mach/pxa2xx-regs.h> +#include <mach/pxafb.h> +#include <mach/i2c.h> +#include <mach/mmc.h> +#include <mach/irda.h> +#include <mach/ohci.h> + +#include "devices.h" #include "generic.h" -static unsigned long magician_pin_config[] = { +static unsigned long magician_pin_config[] __initdata = { /* SDRAM and Static Memory I/O Signals */ GPIO20_nSDCS_2, @@ -131,6 +132,7 @@ static unsigned long magician_pin_config[] = { static void magician_irda_transceiver_mode(struct device *dev, int mode) { gpio_set_value(GPIO83_MAGICIAN_nIR_EN, mode & IR_OFF); + pxa2xx_transceiver_mode(dev, mode); } static struct pxaficp_platform_data magician_ficp_info = { @@ -348,47 +350,66 @@ static struct pxafb_mach_info samsung_info = { * Backlight */ -static void magician_set_bl_intensity(int intensity) +static int magician_backlight_init(struct device *dev) { - if (intensity) { - PWM_CTRL0 = 1; - PWM_PERVAL0 = 0xc8; - if (intensity > 0xc7) { - PWM_PWDUTY0 = intensity - 0x48; - gpio_set_value(EGPIO_MAGICIAN_BL_POWER2, 1); - } else { - PWM_PWDUTY0 = intensity; - gpio_set_value(EGPIO_MAGICIAN_BL_POWER2, 0); - } - gpio_set_value(EGPIO_MAGICIAN_BL_POWER, 1); - pxa_set_cken(CKEN_PWM0, 1); + int ret; + + ret = gpio_request(EGPIO_MAGICIAN_BL_POWER, "BL_POWER"); + if (ret) + goto err; + ret = gpio_request(EGPIO_MAGICIAN_BL_POWER2, "BL_POWER2"); + if (ret) + goto err2; + return 0; + +err2: + gpio_free(EGPIO_MAGICIAN_BL_POWER); +err: + return ret; +} + +static int magician_backlight_notify(int brightness) +{ + gpio_set_value(EGPIO_MAGICIAN_BL_POWER, brightness); + if (brightness >= 200) { + gpio_set_value(EGPIO_MAGICIAN_BL_POWER2, 1); + return brightness - 72; } else { - /* PWM_PWDUTY0 = intensity; */ - gpio_set_value(EGPIO_MAGICIAN_BL_POWER, 0); - pxa_set_cken(CKEN_PWM0, 0); + gpio_set_value(EGPIO_MAGICIAN_BL_POWER2, 0); + return brightness; } } -static struct generic_bl_info backlight_info = { - .default_intensity = 0x64, - .limit_mask = 0x0b, - .max_intensity = 0xc7+0x48, - .set_bl_intensity = magician_set_bl_intensity, +static void magician_backlight_exit(struct device *dev) +{ + gpio_free(EGPIO_MAGICIAN_BL_POWER); + gpio_free(EGPIO_MAGICIAN_BL_POWER2); +} + +static struct platform_pwm_backlight_data backlight_data = { + .pwm_id = 0, + .max_brightness = 272, + .dft_brightness = 100, + .pwm_period_ns = 30923, + .init = magician_backlight_init, + .notify = magician_backlight_notify, + .exit = magician_backlight_exit, }; static struct platform_device backlight = { - .name = "generic-bl", + .name = "pwm-backlight", + .id = -1, .dev = { - .platform_data = &backlight_info, + .parent = &pxa27x_device_pwm0.dev, + .platform_data = &backlight_data, }, - .id = -1, }; /* * LEDs */ -struct gpio_led gpio_leds[] = { +static struct gpio_led gpio_leds[] = { { .name = "magician::vibra", .default_trigger = "none", @@ -490,6 +511,37 @@ static struct platform_device pasic3 = { * External power */ +static int power_supply_init(struct device *dev) +{ + int ret; + + ret = gpio_request(EGPIO_MAGICIAN_CABLE_STATE_AC, "CABLE_STATE_AC"); + if (ret) + goto err_cs_ac; + ret = gpio_request(EGPIO_MAGICIAN_CABLE_STATE_USB, "CABLE_STATE_USB"); + if (ret) + goto err_cs_usb; + ret = gpio_request(EGPIO_MAGICIAN_CHARGE_EN, "CHARGE_EN"); + if (ret) + goto err_chg_en; + ret = gpio_request(GPIO30_MAGICIAN_nCHARGE_EN, "nCHARGE_EN"); + if (!ret) + ret = gpio_direction_output(GPIO30_MAGICIAN_nCHARGE_EN, 0); + if (ret) + goto err_nchg_en; + + return 0; + +err_nchg_en: + gpio_free(EGPIO_MAGICIAN_CHARGE_EN); +err_chg_en: + gpio_free(EGPIO_MAGICIAN_CABLE_STATE_USB); +err_cs_usb: + gpio_free(EGPIO_MAGICIAN_CABLE_STATE_AC); +err_cs_ac: + return ret; +} + static int magician_is_ac_online(void) { return gpio_get_value(EGPIO_MAGICIAN_CABLE_STATE_AC); @@ -506,14 +558,24 @@ static void magician_set_charge(int flags) gpio_set_value(EGPIO_MAGICIAN_CHARGE_EN, flags); } +static void power_supply_exit(struct device *dev) +{ + gpio_free(GPIO30_MAGICIAN_nCHARGE_EN); + gpio_free(EGPIO_MAGICIAN_CHARGE_EN); + gpio_free(EGPIO_MAGICIAN_CABLE_STATE_USB); + gpio_free(EGPIO_MAGICIAN_CABLE_STATE_AC); +} + static char *magician_supplicants[] = { "ds2760-battery.0", "backup-battery" }; static struct pda_power_pdata power_supply_info = { + .init = power_supply_init, .is_ac_online = magician_is_ac_online, .is_usb_online = magician_is_usb_online, .set_charge = magician_set_charge, + .exit = power_supply_exit, .supplied_to = magician_supplicants, .num_supplicants = ARRAY_SIZE(magician_supplicants), }; @@ -607,18 +669,10 @@ static struct pxamci_platform_data magician_mci_info = { * USB OHCI */ -static int magician_ohci_init(struct device *dev) -{ - UHCHR = (UHCHR | UHCHR_SSEP2 | UHCHR_PCPL | UHCHR_CGR) & - ~(UHCHR_SSEP1 | UHCHR_SSEP3 | UHCHR_SSE); - - return 0; -} - static struct pxaohci_platform_data magician_ohci_info = { - .port_mode = PMM_PERPORT_MODE, - .init = magician_ohci_init, - .power_budget = 0, + .port_mode = PMM_PERPORT_MODE, + .flags = ENABLE_PORT1 | ENABLE_PORT3 | POWER_CONTROL_LOW, + .power_budget = 0, }; diff --git a/arch/arm/mach-pxa/mainstone.c b/arch/arm/mach-pxa/mainstone.c index 7399fb34da4..f2c7ad8f2b6 100644 --- a/arch/arm/mach-pxa/mainstone.c +++ b/arch/arm/mach-pxa/mainstone.c @@ -23,15 +23,16 @@ #include <linux/ioport.h> #include <linux/mtd/mtd.h> #include <linux/mtd/partitions.h> -#include <linux/backlight.h> #include <linux/input.h> #include <linux/gpio_keys.h> +#include <linux/pwm_backlight.h> +#include <linux/smc91x.h> #include <asm/types.h> #include <asm/setup.h> #include <asm/memory.h> #include <asm/mach-types.h> -#include <asm/hardware.h> +#include <mach/hardware.h> #include <asm/irq.h> #include <asm/sizes.h> @@ -40,17 +41,17 @@ #include <asm/mach/irq.h> #include <asm/mach/flash.h> -#include <asm/arch/pxa-regs.h> -#include <asm/arch/pxa2xx-regs.h> -#include <asm/arch/mfp-pxa27x.h> -#include <asm/arch/mainstone.h> -#include <asm/arch/audio.h> -#include <asm/arch/pxafb.h> -#include <asm/arch/i2c.h> -#include <asm/arch/mmc.h> -#include <asm/arch/irda.h> -#include <asm/arch/ohci.h> -#include <asm/arch/pxa27x_keypad.h> +#include <mach/pxa-regs.h> +#include <mach/pxa2xx-regs.h> +#include <mach/mfp-pxa27x.h> +#include <mach/mainstone.h> +#include <mach/audio.h> +#include <mach/pxafb.h> +#include <mach/i2c.h> +#include <mach/mmc.h> +#include <mach/irda.h> +#include <mach/ohci.h> +#include <mach/pxa27x_keypad.h> #include "generic.h" #include "devices.h" @@ -110,9 +111,9 @@ static unsigned long mainstone_pin_config[] = { GPIO45_AC97_SYSCLK, /* Keypad */ - GPIO93_KP_DKIN_0 | WAKEUP_ON_LEVEL_HIGH, - GPIO94_KP_DKIN_1 | WAKEUP_ON_LEVEL_HIGH, - GPIO95_KP_DKIN_2 | WAKEUP_ON_LEVEL_HIGH, + GPIO93_KP_DKIN_0, + GPIO94_KP_DKIN_1, + GPIO95_KP_DKIN_2, GPIO100_KP_MKIN_0 | WAKEUP_ON_LEVEL_HIGH, GPIO101_KP_MKIN_1 | WAKEUP_ON_LEVEL_HIGH, GPIO102_KP_MKIN_2 | WAKEUP_ON_LEVEL_HIGH, @@ -161,8 +162,7 @@ static void mainstone_irq_handler(unsigned int irq, struct irq_desc *desc) GEDR(0) = GPIO_bit(0); /* clear useless edge notification */ if (likely(pending)) { irq = MAINSTONE_IRQ(0) + __ffs(pending); - desc = irq_desc + irq; - desc_handle_irq(irq, desc); + generic_handle_irq(irq); } pending = MST_INTSETCLR & mainstone_irq_enabled; } while (pending); @@ -190,7 +190,7 @@ static void __init mainstone_init_irq(void) MST_INTSETCLR = 0; set_irq_chained_handler(IRQ_GPIO(0), mainstone_irq_handler); - set_irq_type(IRQ_GPIO(0), IRQT_FALLING); + set_irq_type(IRQ_GPIO(0), IRQ_TYPE_EDGE_FALLING); } #ifdef CONFIG_PM @@ -240,11 +240,19 @@ static struct resource smc91x_resources[] = { } }; +static struct smc91x_platdata mainstone_smc91x_info = { + .flags = SMC91X_USE_8BIT | SMC91X_USE_16BIT | SMC91X_USE_32BIT | + SMC91X_NOWAIT | SMC91X_USE_DMA, +}; + static struct platform_device smc91x_device = { .name = "smc91x", .id = 0, .num_resources = ARRAY_SIZE(smc91x_resources), .resource = smc91x_resources, + .dev = { + .platform_data = &mainstone_smc91x_info, + }, }; static int mst_audio_startup(struct snd_pcm_substream *substream, void *priv) @@ -280,12 +288,6 @@ static pxa2xx_audio_ops_t mst_audio_ops = { .resume = mst_audio_resume, }; -static struct platform_device mst_audio_device = { - .name = "pxa2xx-ac97", - .id = -1, - .dev = { .platform_data = &mst_audio_ops }, -}; - static struct resource flash_resources[] = { [0] = { .start = PXA_CS0_PHYS, @@ -349,56 +351,27 @@ static struct platform_device mst_flash_device[2] = { }, }; -#ifdef CONFIG_BACKLIGHT_CLASS_DEVICE -static int mainstone_backlight_update_status(struct backlight_device *bl) -{ - int brightness = bl->props.brightness; - - if (bl->props.power != FB_BLANK_UNBLANK || - bl->props.fb_blank != FB_BLANK_UNBLANK) - brightness = 0; - - if (brightness != 0) - pxa_set_cken(CKEN_PWM0, 1); - - PWM_CTRL0 = 0; - PWM_PWDUTY0 = brightness; - PWM_PERVAL0 = bl->props.max_brightness; - - if (brightness == 0) - pxa_set_cken(CKEN_PWM0, 0); - return 0; /* pointless return value */ -} - -static int mainstone_backlight_get_brightness(struct backlight_device *bl) -{ - return PWM_PWDUTY0; -} +#if defined(CONFIG_FB_PXA) || defined(CONFIG_FB_PXA_MODULE) +static struct platform_pwm_backlight_data mainstone_backlight_data = { + .pwm_id = 0, + .max_brightness = 1023, + .dft_brightness = 1023, + .pwm_period_ns = 78770, +}; -static /*const*/ struct backlight_ops mainstone_backlight_ops = { - .update_status = mainstone_backlight_update_status, - .get_brightness = mainstone_backlight_get_brightness, +static struct platform_device mainstone_backlight_device = { + .name = "pwm-backlight", + .dev = { + .parent = &pxa27x_device_pwm0.dev, + .platform_data = &mainstone_backlight_data, + }, }; static void __init mainstone_backlight_register(void) { - struct backlight_device *bl; - - bl = backlight_device_register("mainstone-bl", &pxa_device_fb.dev, - NULL, &mainstone_backlight_ops); - if (IS_ERR(bl)) { - printk(KERN_ERR "mainstone: unable to register backlight: %ld\n", - PTR_ERR(bl)); - return; - } - - /* - * broken design - register-then-setup interfaces are - * utterly broken by definition. - */ - bl->props.max_brightness = 1023; - bl->props.brightness = 1023; - backlight_update_status(bl); + int ret = platform_device_register(&mainstone_backlight_device); + if (ret) + printk(KERN_ERR "mainstone: failed to register backlight device: %d\n", ret); } #else #define mainstone_backlight_register() do { } while (0) @@ -490,6 +463,7 @@ static void mainstone_irda_transceiver_mode(struct device *dev, int mode) } else if (mode & IR_FIRMODE) { MST_MSCWR1 |= MST_MSCWR1_IRDA_FIR; } + pxa2xx_transceiver_mode(dev, mode); if (mode & IR_OFF) { MST_MSCWR1 = (MST_MSCWR1 & ~MST_MSCWR1_IRDA_MASK) | MST_MSCWR1_IRDA_OFF; } else { @@ -528,28 +502,17 @@ static struct platform_device mst_gpio_keys_device = { static struct platform_device *platform_devices[] __initdata = { &smc91x_device, - &mst_audio_device, &mst_flash_device[0], &mst_flash_device[1], &mst_gpio_keys_device, }; -static int mainstone_ohci_init(struct device *dev) -{ - /* Set the Power Control Polarity Low and Power Sense - Polarity Low to active low. */ - UHCHR = (UHCHR | UHCHR_PCPL | UHCHR_PSPL) & - ~(UHCHR_SSEP1 | UHCHR_SSEP2 | UHCHR_SSEP3 | UHCHR_SSE); - - return 0; -} - static struct pxaohci_platform_data mainstone_ohci_platform_data = { .port_mode = PMM_PERPORT_MODE, - .init = mainstone_ohci_init, + .flags = ENABLE_PORT_ALL | POWER_CONTROL_LOW | POWER_SENSE_LOW, }; -#if defined(CONFIG_KEYBOARD_PXA27x) || defined(CONFIG_KEYBOARD_PXA27x_MODULES) +#if defined(CONFIG_KEYBOARD_PXA27x) || defined(CONFIG_KEYBOARD_PXA27x_MODULE) static unsigned int mainstone_matrix_keys[] = { KEY(0, 0, KEY_A), KEY(1, 0, KEY_B), KEY(2, 0, KEY_C), KEY(3, 0, KEY_D), KEY(4, 0, KEY_E), KEY(5, 0, KEY_F), @@ -638,6 +601,7 @@ static void __init mainstone_init(void) pxa_set_ficp_info(&mainstone_ficp_platform_data); pxa_set_ohci_info(&mainstone_ohci_platform_data); pxa_set_i2c_info(NULL); + pxa_set_ac97_info(&mst_audio_ops); mainstone_init_keypad(); } diff --git a/arch/arm/mach-pxa/mfp-pxa2xx.c b/arch/arm/mach-pxa/mfp-pxa2xx.c index 22097a1707c..2061c00c8ea 100644 --- a/arch/arm/mach-pxa/mfp-pxa2xx.c +++ b/arch/arm/mach-pxa/mfp-pxa2xx.c @@ -18,13 +18,19 @@ #include <linux/init.h> #include <linux/sysdev.h> -#include <asm/arch/hardware.h> -#include <asm/arch/pxa-regs.h> -#include <asm/arch/mfp-pxa2xx.h> +#include <mach/hardware.h> +#include <mach/pxa-regs.h> +#include <mach/pxa2xx-regs.h> +#include <mach/mfp-pxa2xx.h> #include "generic.h" -#define PGSR(x) __REG2(0x40F00020, ((x) & 0x60) >> 3) +#define gpio_to_bank(gpio) ((gpio) >> 5) + +#define PGSR(x) __REG2(0x40F00020, (x) << 2) +#define __GAFR(u, x) __REG2((u) ? 0x40E00058 : 0x40E00054, (x) << 3) +#define GAFR_L(x) __GAFR(0, x) +#define GAFR_U(x) __GAFR(1, x) #define PWER_WE35 (1 << 24) @@ -37,41 +43,60 @@ struct gpio_desc { }; static struct gpio_desc gpio_desc[MFP_PIN_GPIO127 + 1]; +static int gpio_nr; + +static unsigned long gpdr_lpm[4]; static int __mfp_config_gpio(unsigned gpio, unsigned long c) { unsigned long gafr, mask = GPIO_bit(gpio); - int fn; + int bank = gpio_to_bank(gpio); + int uorl = !!(gpio & 0x10); /* GAFRx_U or GAFRx_L ? */ + int shft = (gpio & 0xf) << 1; + int fn = MFP_AF(c); + int dir = c & MFP_DIR_OUT; - fn = MFP_AF(c); if (fn > 3) return -EINVAL; - /* alternate function and direction */ - gafr = GAFR(gpio) & ~(0x3 << ((gpio & 0xf) * 2)); - GAFR(gpio) = gafr | (fn << ((gpio & 0xf) * 2)); + /* alternate function and direction at run-time */ + gafr = (uorl == 0) ? GAFR_L(bank) : GAFR_U(bank); + gafr = (gafr & ~(0x3 << shft)) | (fn << shft); + + if (uorl == 0) + GAFR_L(bank) = gafr; + else + GAFR_U(bank) = gafr; - if (c & MFP_DIR_OUT) + if (dir == MFP_DIR_OUT) GPDR(gpio) |= mask; else GPDR(gpio) &= ~mask; - /* low power state */ + /* alternate function and direction at low power mode */ switch (c & MFP_LPM_STATE_MASK) { case MFP_LPM_DRIVE_HIGH: - PGSR(gpio) |= mask; + PGSR(bank) |= mask; + dir = MFP_DIR_OUT; break; case MFP_LPM_DRIVE_LOW: - PGSR(gpio) &= ~mask; + PGSR(bank) &= ~mask; + dir = MFP_DIR_OUT; break; - case MFP_LPM_INPUT: + case MFP_LPM_DEFAULT: break; default: - pr_warning("%s: invalid low power state for GPIO%d\n", + /* warning and fall through, treat as MFP_LPM_DEFAULT */ + pr_warning("%s: GPIO%d: unsupported low power mode\n", __func__, gpio); - return -EINVAL; + break; } + if (dir == MFP_DIR_OUT) + gpdr_lpm[bank] |= mask; + else + gpdr_lpm[bank] &= ~mask; + /* give early warning if MFP_LPM_CAN_WAKEUP is set on the * configurations of those pins not able to wakeup */ @@ -81,7 +106,7 @@ static int __mfp_config_gpio(unsigned gpio, unsigned long c) return -EINVAL; } - if ((c & MFP_LPM_CAN_WAKEUP) && (c & MFP_DIR_OUT)) { + if ((c & MFP_LPM_CAN_WAKEUP) && (dir == MFP_DIR_OUT)) { pr_warning("%s: output GPIO%d unable to wakeup\n", __func__, gpio); return -EINVAL; @@ -90,6 +115,18 @@ static int __mfp_config_gpio(unsigned gpio, unsigned long c) return 0; } +static inline int __mfp_validate(int mfp) +{ + int gpio = mfp_to_gpio(mfp); + + if ((mfp > MFP_PIN_GPIO127) || !gpio_desc[gpio].valid) { + pr_warning("%s: GPIO%d is invalid pin\n", __func__, gpio); + return -1; + } + + return gpio; +} + void pxa2xx_mfp_config(unsigned long *mfp_cfgs, int num) { unsigned long flags; @@ -98,13 +135,9 @@ void pxa2xx_mfp_config(unsigned long *mfp_cfgs, int num) for (i = 0, c = mfp_cfgs; i < num; i++, c++) { - gpio = mfp_to_gpio(MFP_PIN(*c)); - - if (!gpio_desc[gpio].valid) { - pr_warning("%s: GPIO%d is invalid pin\n", - __func__, gpio); + gpio = __mfp_validate(MFP_PIN(*c)); + if (gpio < 0) continue; - } local_irq_save(flags); @@ -115,6 +148,24 @@ void pxa2xx_mfp_config(unsigned long *mfp_cfgs, int num) } } +void pxa2xx_mfp_set_lpm(int mfp, unsigned long lpm) +{ + unsigned long flags, c; + int gpio; + + gpio = __mfp_validate(mfp); + if (gpio < 0) + return; + + local_irq_save(flags); + + c = gpio_desc[gpio].config; + c = (c & ~MFP_LPM_STATE_MASK) | lpm; + __mfp_config_gpio(gpio, c); + + local_irq_restore(flags); +} + int gpio_set_wake(unsigned int gpio, unsigned int on) { struct gpio_desc *d; @@ -155,23 +206,22 @@ int gpio_set_wake(unsigned int gpio, unsigned int on) } #ifdef CONFIG_PXA25x -static int __init pxa25x_mfp_init(void) +static void __init pxa25x_mfp_init(void) { int i; - if (cpu_is_pxa25x()) { - for (i = 0; i <= 84; i++) - gpio_desc[i].valid = 1; + for (i = 0; i <= 84; i++) + gpio_desc[i].valid = 1; - for (i = 0; i <= 15; i++) { - gpio_desc[i].can_wakeup = 1; - gpio_desc[i].mask = GPIO_bit(i); - } + for (i = 0; i <= 15; i++) { + gpio_desc[i].can_wakeup = 1; + gpio_desc[i].mask = GPIO_bit(i); } - return 0; + gpio_nr = 85; } -postcore_initcall(pxa25x_mfp_init); +#else +static inline void pxa25x_mfp_init(void) {} #endif /* CONFIG_PXA25x */ #ifdef CONFIG_PXA27x @@ -201,45 +251,106 @@ int keypad_set_wake(unsigned int on) return 0; } -static int __init pxa27x_mfp_init(void) +static void __init pxa27x_mfp_init(void) { int i, gpio; - if (cpu_is_pxa27x()) { - for (i = 0; i <= 120; i++) { - /* skip GPIO2, 5, 6, 7, 8, they are not - * valid pins allow configuration - */ - if (i == 2 || i == 5 || i == 6 || - i == 7 || i == 8) - continue; + for (i = 0; i <= 120; i++) { + /* skip GPIO2, 5, 6, 7, 8, they are not + * valid pins allow configuration + */ + if (i == 2 || i == 5 || i == 6 || i == 7 || i == 8) + continue; - gpio_desc[i].valid = 1; - } + gpio_desc[i].valid = 1; + } - /* Keypad GPIOs */ - for (i = 0; i < ARRAY_SIZE(pxa27x_pkwr_gpio); i++) { - gpio = pxa27x_pkwr_gpio[i]; - gpio_desc[gpio].can_wakeup = 1; - gpio_desc[gpio].keypad_gpio = 1; - gpio_desc[gpio].mask = 1 << i; - } + /* Keypad GPIOs */ + for (i = 0; i < ARRAY_SIZE(pxa27x_pkwr_gpio); i++) { + gpio = pxa27x_pkwr_gpio[i]; + gpio_desc[gpio].can_wakeup = 1; + gpio_desc[gpio].keypad_gpio = 1; + gpio_desc[gpio].mask = 1 << i; + } - /* Overwrite GPIO13 as a PWER wakeup source */ - for (i = 0; i <= 15; i++) { - /* skip GPIO2, 5, 6, 7, 8 */ - if (GPIO_bit(i) & 0x1e4) - continue; + /* Overwrite GPIO13 as a PWER wakeup source */ + for (i = 0; i <= 15; i++) { + /* skip GPIO2, 5, 6, 7, 8 */ + if (GPIO_bit(i) & 0x1e4) + continue; - gpio_desc[i].can_wakeup = 1; - gpio_desc[i].mask = GPIO_bit(i); - } + gpio_desc[i].can_wakeup = 1; + gpio_desc[i].mask = GPIO_bit(i); + } + + gpio_desc[35].can_wakeup = 1; + gpio_desc[35].mask = PWER_WE35; + + gpio_nr = 121; +} +#else +static inline void pxa27x_mfp_init(void) {} +#endif /* CONFIG_PXA27x */ - gpio_desc[35].can_wakeup = 1; - gpio_desc[35].mask = PWER_WE35; +#ifdef CONFIG_PM +static unsigned long saved_gafr[2][4]; +static unsigned long saved_gpdr[4]; + +static int pxa2xx_mfp_suspend(struct sys_device *d, pm_message_t state) +{ + int i; + + for (i = 0; i <= gpio_to_bank(gpio_nr); i++) { + + saved_gafr[0][i] = GAFR_L(i); + saved_gafr[1][i] = GAFR_U(i); + saved_gpdr[i] = GPDR(i * 32); + + GPDR(i * 32) = gpdr_lpm[i]; } + return 0; +} +static int pxa2xx_mfp_resume(struct sys_device *d) +{ + int i; + + for (i = 0; i <= gpio_to_bank(gpio_nr); i++) { + GAFR_L(i) = saved_gafr[0][i]; + GAFR_U(i) = saved_gafr[1][i]; + GPDR(i * 32) = saved_gpdr[i]; + } + PSSR = PSSR_RDH | PSSR_PH; return 0; } -postcore_initcall(pxa27x_mfp_init); -#endif /* CONFIG_PXA27x */ +#else +#define pxa2xx_mfp_suspend NULL +#define pxa2xx_mfp_resume NULL +#endif + +struct sysdev_class pxa2xx_mfp_sysclass = { + .name = "mfp", + .suspend = pxa2xx_mfp_suspend, + .resume = pxa2xx_mfp_resume, +}; + +static int __init pxa2xx_mfp_init(void) +{ + int i; + + if (!cpu_is_pxa2xx()) + return 0; + + if (cpu_is_pxa25x()) + pxa25x_mfp_init(); + + if (cpu_is_pxa27x()) + pxa27x_mfp_init(); + + /* initialize gafr_run[], pgsr_lpm[] from existing values */ + for (i = 0; i <= gpio_to_bank(gpio_nr); i++) + gpdr_lpm[i] = GPDR(i * 32); + + return sysdev_class_register(&pxa2xx_mfp_sysclass); +} +postcore_initcall(pxa2xx_mfp_init); diff --git a/arch/arm/mach-pxa/mfp-pxa3xx.c b/arch/arm/mach-pxa/mfp-pxa3xx.c index 3a5b0fcbaf1..eb197a6e8e9 100644 --- a/arch/arm/mach-pxa/mfp-pxa3xx.c +++ b/arch/arm/mach-pxa/mfp-pxa3xx.c @@ -19,10 +19,10 @@ #include <linux/io.h> #include <linux/sysdev.h> -#include <asm/hardware.h> -#include <asm/arch/mfp.h> -#include <asm/arch/mfp-pxa3xx.h> -#include <asm/arch/pxa3xx-regs.h> +#include <mach/hardware.h> +#include <mach/mfp.h> +#include <mach/mfp-pxa3xx.h> +#include <mach/pxa3xx-regs.h> /* mfp_spin_lock is used to ensure that MFP register configuration * (most likely a read-modify-write operation) is atomic, and that diff --git a/arch/arm/mach-pxa/mioa701.c b/arch/arm/mach-pxa/mioa701.c new file mode 100644 index 00000000000..0842c531ee4 --- /dev/null +++ b/arch/arm/mach-pxa/mioa701.c @@ -0,0 +1,905 @@ +/* + * Handles the Mitac Mio A701 Board + * + * Copyright (C) 2008 Robert Jarzmik + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA + * + */ + +#include <linux/kernel.h> +#include <linux/init.h> +#include <linux/platform_device.h> +#include <linux/sysdev.h> +#include <linux/input.h> +#include <linux/delay.h> +#include <linux/gpio_keys.h> +#include <linux/pwm_backlight.h> +#include <linux/rtc.h> +#include <linux/leds.h> +#include <linux/gpio.h> +#include <linux/interrupt.h> +#include <linux/irq.h> +#include <linux/pda_power.h> +#include <linux/power_supply.h> +#include <linux/wm97xx.h> +#include <linux/mtd/physmap.h> + +#include <asm/mach-types.h> +#include <asm/mach/arch.h> +#include <mach/mfp-pxa27x.h> +#include <mach/pxa27x_keypad.h> +#include <mach/pxafb.h> +#include <mach/pxa2xx-regs.h> +#include <mach/mmc.h> +#include <mach/udc.h> +#include <mach/pxa27x-udc.h> + +#include <mach/mioa701.h> + +#include "generic.h" +#include "devices.h" + +static unsigned long mioa701_pin_config[] = { + /* Mio global */ + MIO_CFG_OUT(GPIO9_CHARGE_nEN, AF0, DRIVE_LOW), + MIO_CFG_OUT(GPIO18_POWEROFF, AF0, DRIVE_LOW), + MFP_CFG_OUT(GPIO3, AF0, DRIVE_HIGH), + MFP_CFG_OUT(GPIO4, AF0, DRIVE_HIGH), + + /* Backlight PWM 0 */ + GPIO16_PWM0_OUT, + + /* MMC */ + GPIO32_MMC_CLK, + GPIO92_MMC_DAT_0, + GPIO109_MMC_DAT_1, + GPIO110_MMC_DAT_2, + GPIO111_MMC_DAT_3, + GPIO112_MMC_CMD, + MIO_CFG_IN(GPIO78_SDIO_RO, AF0), + MIO_CFG_IN(GPIO15_SDIO_INSERT, AF0), + MIO_CFG_OUT(GPIO91_SDIO_EN, AF0, DRIVE_LOW), + + /* USB */ + MIO_CFG_IN(GPIO13_USB_DETECT, AF0), + MIO_CFG_OUT(GPIO22_USB_ENABLE, AF0, DRIVE_LOW), + + /* LCD */ + GPIO58_LCD_LDD_0, + GPIO59_LCD_LDD_1, + GPIO60_LCD_LDD_2, + GPIO61_LCD_LDD_3, + GPIO62_LCD_LDD_4, + GPIO63_LCD_LDD_5, + GPIO64_LCD_LDD_6, + GPIO65_LCD_LDD_7, + GPIO66_LCD_LDD_8, + GPIO67_LCD_LDD_9, + GPIO68_LCD_LDD_10, + GPIO69_LCD_LDD_11, + GPIO70_LCD_LDD_12, + GPIO71_LCD_LDD_13, + GPIO72_LCD_LDD_14, + GPIO73_LCD_LDD_15, + GPIO74_LCD_FCLK, + GPIO75_LCD_LCLK, + GPIO76_LCD_PCLK, + + /* Bluetooth */ + GPIO44_BTUART_CTS, + GPIO42_BTUART_RXD, + GPIO45_BTUART_RTS, + GPIO43_BTUART_TXD, + MIO_CFG_OUT(GPIO83_BT_ON, AF0, DRIVE_LOW), + + /* GPS */ + MIO_CFG_OUT(GPIO23_GPS_UNKNOWN1, AF0, DRIVE_LOW), + MIO_CFG_OUT(GPIO26_GPS_ON, AF0, DRIVE_LOW), + MIO_CFG_OUT(GPIO27_GPS_RESET, AF0, DRIVE_LOW), + MIO_CFG_OUT(GPIO106_GPS_UNKNOWN2, AF0, DRIVE_LOW), + MIO_CFG_OUT(GPIO107_GPS_UNKNOWN3, AF0, DRIVE_LOW), + GPIO46_STUART_RXD, + GPIO47_STUART_TXD, + + /* GSM */ + MIO_CFG_OUT(GPIO24_GSM_MOD_RESET_CMD, AF0, DRIVE_LOW), + MIO_CFG_OUT(GPIO88_GSM_nMOD_ON_CMD, AF0, DRIVE_HIGH), + MIO_CFG_OUT(GPIO90_GSM_nMOD_OFF_CMD, AF0, DRIVE_HIGH), + MIO_CFG_OUT(GPIO114_GSM_nMOD_DTE_UART_STATE, AF0, DRIVE_HIGH), + MIO_CFG_IN(GPIO25_GSM_MOD_ON_STATE, AF0), + MIO_CFG_IN(GPIO113_GSM_EVENT, AF0) | WAKEUP_ON_EDGE_BOTH, + GPIO34_FFUART_RXD, + GPIO35_FFUART_CTS, + GPIO36_FFUART_DCD, + GPIO37_FFUART_DSR, + GPIO39_FFUART_TXD, + GPIO40_FFUART_DTR, + GPIO41_FFUART_RTS, + + /* Sound */ + GPIO89_AC97_SYSCLK, + MIO_CFG_IN(GPIO12_HPJACK_INSERT, AF0), + + /* Leds */ + MIO_CFG_OUT(GPIO10_LED_nCharging, AF0, DRIVE_HIGH), + MIO_CFG_OUT(GPIO97_LED_nBlue, AF0, DRIVE_HIGH), + MIO_CFG_OUT(GPIO98_LED_nOrange, AF0, DRIVE_HIGH), + MIO_CFG_OUT(GPIO82_LED_nVibra, AF0, DRIVE_HIGH), + MIO_CFG_OUT(GPIO115_LED_nKeyboard, AF0, DRIVE_HIGH), + + /* Keyboard */ + MIO_CFG_IN(GPIO0_KEY_POWER, AF0) | WAKEUP_ON_EDGE_BOTH, + MIO_CFG_IN(GPIO93_KEY_VOLUME_UP, AF0), + MIO_CFG_IN(GPIO94_KEY_VOLUME_DOWN, AF0), + GPIO100_KP_MKIN_0, + GPIO101_KP_MKIN_1, + GPIO102_KP_MKIN_2, + GPIO103_KP_MKOUT_0, + GPIO104_KP_MKOUT_1, + GPIO105_KP_MKOUT_2, + + /* Unknown */ + MFP_CFG_IN(GPIO14, AF0), + MFP_CFG_IN(GPIO20, AF0), + MFP_CFG_IN(GPIO21, AF0), + MFP_CFG_IN(GPIO33, AF0), + MFP_CFG_OUT(GPIO49, AF0, DRIVE_HIGH), + MFP_CFG_OUT(GPIO57, AF0, DRIVE_HIGH), + MFP_CFG_OUT(GPIO77, AF0, DRIVE_HIGH), + MFP_CFG_IN(GPIO80, AF0), + MFP_CFG_OUT(GPIO86, AF0, DRIVE_HIGH), + MFP_CFG_IN(GPIO96, AF0), + MFP_CFG_OUT(GPIO116, AF0, DRIVE_HIGH), +}; + +#define MIO_GPIO_IN(num, _desc) \ + { .gpio = (num), .dir = 0, .desc = (_desc) } +#define MIO_GPIO_OUT(num, _init, _desc) \ + { .gpio = (num), .dir = 1, .init = (_init), .desc = (_desc) } +struct gpio_ress { + unsigned gpio : 8; + unsigned dir : 1; + unsigned init : 1; + char *desc; +}; + +static int mio_gpio_request(struct gpio_ress *gpios, int size) +{ + int i, rc = 0; + int gpio; + int dir; + + for (i = 0; (!rc) && (i < size); i++) { + gpio = gpios[i].gpio; + dir = gpios[i].dir; + rc = gpio_request(gpio, gpios[i].desc); + if (rc) { + printk(KERN_ERR "Error requesting GPIO %d(%s) : %d\n", + gpio, gpios[i].desc, rc); + continue; + } + if (dir) + gpio_direction_output(gpio, gpios[i].init); + else + gpio_direction_input(gpio); + } + while ((rc) && (--i >= 0)) + gpio_free(gpios[i].gpio); + return rc; +} + +static void mio_gpio_free(struct gpio_ress *gpios, int size) +{ + int i; + + for (i = 0; i < size; i++) + gpio_free(gpios[i].gpio); +} + +/* LCD Screen and Backlight */ +static struct platform_pwm_backlight_data mioa701_backlight_data = { + .pwm_id = 0, + .max_brightness = 100, + .dft_brightness = 50, + .pwm_period_ns = 4000 * 1024, /* Fl = 250kHz */ +}; + +/* + * LTM0305A776C LCD panel timings + * + * see: + * - the LTM0305A776C datasheet, + * - and the PXA27x Programmers' manual + */ +static struct pxafb_mode_info mioa701_ltm0305a776c = { + .pixclock = 220000, /* CLK=4.545 MHz */ + .xres = 240, + .yres = 320, + .bpp = 16, + .hsync_len = 4, + .vsync_len = 2, + .left_margin = 6, + .right_margin = 4, + .upper_margin = 5, + .lower_margin = 3, +}; + +static void mioa701_lcd_power(int on, struct fb_var_screeninfo *si) +{ + gpio_set_value(GPIO87_LCD_POWER, on); +} + +static struct pxafb_mach_info mioa701_pxafb_info = { + .modes = &mioa701_ltm0305a776c, + .num_modes = 1, + .lcd_conn = LCD_COLOR_TFT_16BPP | LCD_PCLK_EDGE_FALL, + .pxafb_lcd_power = mioa701_lcd_power, +}; + +/* + * Keyboard configuration + */ +static unsigned int mioa701_matrix_keys[] = { + KEY(0, 0, KEY_UP), + KEY(0, 1, KEY_RIGHT), + KEY(0, 2, KEY_MEDIA), + KEY(1, 0, KEY_DOWN), + KEY(1, 1, KEY_ENTER), + KEY(1, 2, KEY_CONNECT), /* GPS key */ + KEY(2, 0, KEY_LEFT), + KEY(2, 1, KEY_PHONE), /* Phone Green key */ + KEY(2, 2, KEY_CAMERA) /* Camera key */ +}; +static struct pxa27x_keypad_platform_data mioa701_keypad_info = { + .matrix_key_rows = 3, + .matrix_key_cols = 3, + .matrix_key_map = mioa701_matrix_keys, + .matrix_key_map_size = ARRAY_SIZE(mioa701_matrix_keys), +}; + +/* + * GPIO Key Configuration + */ +#define MIO_KEY(key, _gpio, _desc, _wakeup) \ + { .code = (key), .gpio = (_gpio), .active_low = 0, \ + .desc = (_desc), .type = EV_KEY, .wakeup = (_wakeup) } +static struct gpio_keys_button mioa701_button_table[] = { + MIO_KEY(KEY_EXIT, GPIO0_KEY_POWER, "Power button", 1), + MIO_KEY(KEY_VOLUMEUP, GPIO93_KEY_VOLUME_UP, "Volume up", 0), + MIO_KEY(KEY_VOLUMEDOWN, GPIO94_KEY_VOLUME_DOWN, "Volume down", 0), + MIO_KEY(KEY_HP, GPIO12_HPJACK_INSERT, "HP jack detect", 0) +}; + +static struct gpio_keys_platform_data mioa701_gpio_keys_data = { + .buttons = mioa701_button_table, + .nbuttons = ARRAY_SIZE(mioa701_button_table), +}; + +/* + * Leds and vibrator + */ +#define ONE_LED(_gpio, _name) \ +{ .gpio = (_gpio), .name = (_name), .active_low = true } +static struct gpio_led gpio_leds[] = { + ONE_LED(GPIO10_LED_nCharging, "mioa701:charging"), + ONE_LED(GPIO97_LED_nBlue, "mioa701:blue"), + ONE_LED(GPIO98_LED_nOrange, "mioa701:orange"), + ONE_LED(GPIO82_LED_nVibra, "mioa701:vibra"), + ONE_LED(GPIO115_LED_nKeyboard, "mioa701:keyboard") +}; + +static struct gpio_led_platform_data gpio_led_info = { + .leds = gpio_leds, + .num_leds = ARRAY_SIZE(gpio_leds), +}; + +/* + * GSM Sagem XS200 chip + * + * GSM handling was purged from kernel. For history, this is the way to go : + * - init : GPIO24_GSM_MOD_RESET_CMD = 0, GPIO114_GSM_nMOD_DTE_UART_STATE = 1 + * GPIO88_GSM_nMOD_ON_CMD = 1, GPIO90_GSM_nMOD_OFF_CMD = 1 + * - reset : GPIO24_GSM_MOD_RESET_CMD = 1, msleep(100), + * GPIO24_GSM_MOD_RESET_CMD = 0 + * - turn on : GPIO88_GSM_nMOD_ON_CMD = 0, msleep(1000), + * GPIO88_GSM_nMOD_ON_CMD = 1 + * - turn off : GPIO90_GSM_nMOD_OFF_CMD = 0, msleep(1000), + * GPIO90_GSM_nMOD_OFF_CMD = 1 + */ +static int is_gsm_on(void) +{ + int is_on; + + is_on = !!gpio_get_value(GPIO25_GSM_MOD_ON_STATE); + return is_on; +} + +irqreturn_t gsm_on_irq(int irq, void *p) +{ + printk(KERN_DEBUG "Mioa701: GSM status changed to %s\n", + is_gsm_on() ? "on" : "off"); + return IRQ_HANDLED; +} + +struct gpio_ress gsm_gpios[] = { + MIO_GPIO_IN(GPIO25_GSM_MOD_ON_STATE, "GSM state"), + MIO_GPIO_IN(GPIO113_GSM_EVENT, "GSM event"), +}; + +static int __init gsm_init(void) +{ + int rc; + + rc = mio_gpio_request(ARRAY_AND_SIZE(gsm_gpios)); + if (rc) + goto err_gpio; + rc = request_irq(gpio_to_irq(GPIO25_GSM_MOD_ON_STATE), gsm_on_irq, + IRQF_TRIGGER_RISING | IRQF_TRIGGER_FALLING, + "GSM XS200 Power Irq", NULL); + if (rc) + goto err_irq; + + gpio_set_wake(GPIO113_GSM_EVENT, 1); + return 0; + +err_irq: + printk(KERN_ERR "Mioa701: Can't request GSM_ON irq\n"); + mio_gpio_free(ARRAY_AND_SIZE(gsm_gpios)); +err_gpio: + printk(KERN_ERR "Mioa701: gsm not available\n"); + return rc; +} + +static void gsm_exit(void) +{ + free_irq(gpio_to_irq(GPIO25_GSM_MOD_ON_STATE), NULL); + mio_gpio_free(ARRAY_AND_SIZE(gsm_gpios)); +} + +/* + * Bluetooth BRF6150 chip + * + * BT handling was purged from kernel. For history, this is the way to go : + * - turn on : GPIO83_BT_ON = 1 + * - turn off : GPIO83_BT_ON = 0 + */ + +/* + * GPS Sirf Star III chip + * + * GPS handling was purged from kernel. For history, this is the way to go : + * - init : GPIO23_GPS_UNKNOWN1 = 1, GPIO26_GPS_ON = 0, GPIO27_GPS_RESET = 0 + * GPIO106_GPS_UNKNOWN2 = 0, GPIO107_GPS_UNKNOWN3 = 0 + * - turn on : GPIO27_GPS_RESET = 1, GPIO26_GPS_ON = 1 + * - turn off : GPIO26_GPS_ON = 0, GPIO27_GPS_RESET = 0 + */ + +/* + * USB UDC + */ +static void udc_power_command(int cmd) +{ + switch (cmd) { + case PXA2XX_UDC_CMD_DISCONNECT: + gpio_set_value(GPIO22_USB_ENABLE, 0); + break; + case PXA2XX_UDC_CMD_CONNECT: + gpio_set_value(GPIO22_USB_ENABLE, 1); + break; + default: + printk(KERN_INFO "udc_control: unknown command (0x%x)!\n", cmd); + break; + } +} + +static int is_usb_connected(void) +{ + return !!gpio_get_value(GPIO13_USB_DETECT); +} + +static struct pxa2xx_udc_mach_info mioa701_udc_info = { + .udc_is_connected = is_usb_connected, + .udc_command = udc_power_command, +}; + +struct gpio_ress udc_gpios[] = { + MIO_GPIO_OUT(GPIO22_USB_ENABLE, 0, "USB Vbus enable") +}; + +static int __init udc_init(void) +{ + pxa_set_udc_info(&mioa701_udc_info); + return mio_gpio_request(ARRAY_AND_SIZE(udc_gpios)); +} + +static void udc_exit(void) +{ + mio_gpio_free(ARRAY_AND_SIZE(udc_gpios)); +} + +/* + * SDIO/MMC Card controller + */ +static void mci_setpower(struct device *dev, unsigned int vdd) +{ + struct pxamci_platform_data *p_d = dev->platform_data; + + if ((1 << vdd) & p_d->ocr_mask) + gpio_set_value(GPIO91_SDIO_EN, 1); /* enable SDIO power */ + else + gpio_set_value(GPIO91_SDIO_EN, 0); /* disable SDIO power */ +} + +static int mci_get_ro(struct device *dev) +{ + return gpio_get_value(GPIO78_SDIO_RO); +} + +struct gpio_ress mci_gpios[] = { + MIO_GPIO_IN(GPIO78_SDIO_RO, "SDIO readonly detect"), + MIO_GPIO_IN(GPIO15_SDIO_INSERT, "SDIO insertion detect"), + MIO_GPIO_OUT(GPIO91_SDIO_EN, 0, "SDIO power enable") +}; + +static void mci_exit(struct device *dev, void *data) +{ + mio_gpio_free(ARRAY_AND_SIZE(mci_gpios)); + free_irq(gpio_to_irq(GPIO15_SDIO_INSERT), data); +} + +static struct pxamci_platform_data mioa701_mci_info; + +/** + * The card detect interrupt isn't debounced so we delay it by 250ms + * to give the card a chance to fully insert/eject. + */ +static int mci_init(struct device *dev, irq_handler_t detect_int, void *data) +{ + int rc; + int irq = gpio_to_irq(GPIO15_SDIO_INSERT); + + rc = mio_gpio_request(ARRAY_AND_SIZE(mci_gpios)); + if (rc) + goto err_gpio; + /* enable RE/FE interrupt on card insertion and removal */ + rc = request_irq(irq, detect_int, + IRQF_DISABLED | IRQF_TRIGGER_RISING | + IRQF_TRIGGER_FALLING, + "MMC card detect", data); + if (rc) + goto err_irq; + + mioa701_mci_info.detect_delay = msecs_to_jiffies(250); + return 0; + +err_irq: + dev_err(dev, "mioa701_mci_init: MMC/SD:" + " can't request MMC card detect IRQ\n"); + mio_gpio_free(ARRAY_AND_SIZE(mci_gpios)); +err_gpio: + return rc; +} + +static struct pxamci_platform_data mioa701_mci_info = { + .ocr_mask = MMC_VDD_32_33 | MMC_VDD_33_34, + .init = mci_init, + .get_ro = mci_get_ro, + .setpower = mci_setpower, + .exit = mci_exit, +}; + +/* FlashRAM */ +static struct resource strataflash_resource = { + .start = PXA_CS0_PHYS, + .end = PXA_CS0_PHYS + SZ_64M - 1, + .flags = IORESOURCE_MEM, +}; + +static struct physmap_flash_data strataflash_data = { + .width = 2, + /* .set_vpp = mioa701_set_vpp, */ +}; + +static struct platform_device strataflash = { + .name = "physmap-flash", + .id = -1, + .resource = &strataflash_resource, + .num_resources = 1, + .dev = { + .platform_data = &strataflash_data, + }, +}; + +/* + * Suspend/Resume bootstrap management + * + * MIO A701 reboot sequence is highly ROM dependant. From the one dissassembled, + * this sequence is as follows : + * - disables interrupts + * - initialize SDRAM (self refresh RAM into active RAM) + * - initialize GPIOs (depends on value at 0xa020b020) + * - initialize coprossessors + * - if edge detect on PWR_SCL(GPIO3), then proceed to cold start + * - or if value at 0xa020b000 not equal to 0x0f0f0f0f, proceed to cold start + * - else do a resume, ie. jump to addr 0xa0100000 + */ +#define RESUME_ENABLE_ADDR 0xa020b000 +#define RESUME_ENABLE_VAL 0x0f0f0f0f +#define RESUME_BT_ADDR 0xa020b020 +#define RESUME_UNKNOWN_ADDR 0xa020b024 +#define RESUME_VECTOR_ADDR 0xa0100000 +#define BOOTSTRAP_WORDS mioa701_bootstrap_lg/4 + +static u32 *save_buffer; + +static void install_bootstrap(void) +{ + int i; + u32 *rom_bootstrap = phys_to_virt(RESUME_VECTOR_ADDR); + u32 *src = &mioa701_bootstrap; + + for (i = 0; i < BOOTSTRAP_WORDS; i++) + rom_bootstrap[i] = src[i]; +} + + +static int mioa701_sys_suspend(struct sys_device *sysdev, pm_message_t state) +{ + int i = 0, is_bt_on; + u32 *mem_resume_vector = phys_to_virt(RESUME_VECTOR_ADDR); + u32 *mem_resume_enabler = phys_to_virt(RESUME_ENABLE_ADDR); + u32 *mem_resume_bt = phys_to_virt(RESUME_BT_ADDR); + u32 *mem_resume_unknown = phys_to_virt(RESUME_UNKNOWN_ADDR); + + /* Devices prepare suspend */ + is_bt_on = gpio_get_value(GPIO83_BT_ON); + pxa2xx_mfp_set_lpm(GPIO83_BT_ON, + is_bt_on ? MFP_LPM_DRIVE_HIGH : MFP_LPM_DRIVE_LOW); + + for (i = 0; i < BOOTSTRAP_WORDS; i++) + save_buffer[i] = mem_resume_vector[i]; + save_buffer[i++] = *mem_resume_enabler; + save_buffer[i++] = *mem_resume_bt; + save_buffer[i++] = *mem_resume_unknown; + + *mem_resume_enabler = RESUME_ENABLE_VAL; + *mem_resume_bt = is_bt_on; + + install_bootstrap(); + return 0; +} + +static int mioa701_sys_resume(struct sys_device *sysdev) +{ + int i = 0; + u32 *mem_resume_vector = phys_to_virt(RESUME_VECTOR_ADDR); + u32 *mem_resume_enabler = phys_to_virt(RESUME_ENABLE_ADDR); + u32 *mem_resume_bt = phys_to_virt(RESUME_BT_ADDR); + u32 *mem_resume_unknown = phys_to_virt(RESUME_UNKNOWN_ADDR); + + for (i = 0; i < BOOTSTRAP_WORDS; i++) + mem_resume_vector[i] = save_buffer[i]; + *mem_resume_enabler = save_buffer[i++]; + *mem_resume_bt = save_buffer[i++]; + *mem_resume_unknown = save_buffer[i++]; + + return 0; +} + +static struct sysdev_class mioa701_sysclass = { + .name = "mioa701", +}; + +static struct sys_device sysdev_bootstrap = { + .cls = &mioa701_sysclass, +}; + +static struct sysdev_driver driver_bootstrap = { + .suspend = &mioa701_sys_suspend, + .resume = &mioa701_sys_resume, +}; + +static int __init bootstrap_init(void) +{ + int rc; + int save_size = mioa701_bootstrap_lg + (sizeof(u32) * 3); + + rc = sysdev_class_register(&mioa701_sysclass); + if (rc) { + printk(KERN_ERR "Failed registering mioa701 sys class\n"); + return -ENODEV; + } + rc = sysdev_register(&sysdev_bootstrap); + if (rc) { + printk(KERN_ERR "Failed registering mioa701 sys device\n"); + return -ENODEV; + } + rc = sysdev_driver_register(&mioa701_sysclass, &driver_bootstrap); + if (rc) { + printk(KERN_ERR "Failed registering PMU sys driver\n"); + return -ENODEV; + } + + save_buffer = kmalloc(save_size, GFP_KERNEL); + if (!save_buffer) + return -ENOMEM; + printk(KERN_INFO "MioA701: allocated %d bytes for bootstrap\n", + save_size); + return 0; +} + +static void bootstrap_exit(void) +{ + kfree(save_buffer); + sysdev_driver_unregister(&mioa701_sysclass, &driver_bootstrap); + sysdev_unregister(&sysdev_bootstrap); + sysdev_class_unregister(&mioa701_sysclass); + + printk(KERN_CRIT "Unregistering mioa701 suspend will hang next" + "resume !!!\n"); +} + +/* + * Power Supply + */ +static char *supplicants[] = { + "mioa701_battery" +}; + +static void mioa701_set_charge(int flags) +{ + gpio_set_value(GPIO9_CHARGE_nEN, !flags); +} + +static struct pda_power_pdata power_pdata = { + .is_ac_online = is_usb_connected, + .set_charge = mioa701_set_charge, + .supplied_to = supplicants, + .num_supplicants = ARRAY_SIZE(supplicants), +}; + +static struct resource power_resources[] = { + [0] = { + .name = "ac", + .start = gpio_to_irq(GPIO13_USB_DETECT), + .end = gpio_to_irq(GPIO13_USB_DETECT), + .flags = IORESOURCE_IRQ | IORESOURCE_IRQ_HIGHEDGE | + IORESOURCE_IRQ_LOWEDGE, + }, +}; + +static struct platform_device power_dev = { + .name = "pda-power", + .id = -1, + .resource = power_resources, + .num_resources = ARRAY_SIZE(power_resources), + .dev = { + .platform_data = &power_pdata, + }, +}; + +#if defined(CONFIG_PDA_POWER) && defined(CONFIG_TOUCHSCREEN_WM97XX) +static struct wm97xx *battery_wm; + +static enum power_supply_property battery_props[] = { + POWER_SUPPLY_PROP_STATUS, + POWER_SUPPLY_PROP_VOLTAGE_MAX_DESIGN, + POWER_SUPPLY_PROP_VOLTAGE_MIN_DESIGN, + POWER_SUPPLY_PROP_VOLTAGE_NOW, + POWER_SUPPLY_PROP_CHARGE_FULL_DESIGN, /* Necessary for apm */ +}; + +static int get_battery_voltage(void) +{ + int adc = -1; + + if (battery_wm) + adc = wm97xx_read_aux_adc(battery_wm, WM97XX_AUX_ID1); + return adc; +} + +static int get_battery_status(struct power_supply *b) +{ + int status; + + if (is_usb_connected()) + status = POWER_SUPPLY_STATUS_CHARGING; + else + status = POWER_SUPPLY_STATUS_DISCHARGING; + + return status; +} + +static int get_property(struct power_supply *b, + enum power_supply_property psp, + union power_supply_propval *val) +{ + int rc = 0; + + switch (psp) { + case POWER_SUPPLY_PROP_STATUS: + val->intval = get_battery_status(b); + break; + case POWER_SUPPLY_PROP_VOLTAGE_MAX_DESIGN: + val->intval = 0xfd0; + break; + case POWER_SUPPLY_PROP_VOLTAGE_MIN_DESIGN: + val->intval = 0xc00; + break; + case POWER_SUPPLY_PROP_VOLTAGE_NOW: + val->intval = get_battery_voltage(); + break; + case POWER_SUPPLY_PROP_CHARGE_FULL_DESIGN: + val->intval = 100; + break; + default: + val->intval = -1; + rc = -1; + } + + return rc; +}; + +static struct power_supply battery_ps = { + .name = "mioa701_battery", + .type = POWER_SUPPLY_TYPE_BATTERY, + .get_property = get_property, + .properties = battery_props, + .num_properties = ARRAY_SIZE(battery_props), +}; + +static int battery_probe(struct platform_device *pdev) +{ + struct wm97xx *wm = platform_get_drvdata(pdev); + int rc; + + battery_wm = wm; + + rc = power_supply_register(NULL, &battery_ps); + if (rc) + dev_err(&pdev->dev, + "Could not register mioa701 battery -> %d\n", rc); + return rc; +} + +static int battery_remove(struct platform_device *pdev) +{ + battery_wm = NULL; + return 0; +} + +static struct platform_driver mioa701_battery_driver = { + .driver = { + .name = "wm97xx-battery", + }, + .probe = battery_probe, + .remove = battery_remove +}; + +static int __init mioa701_battery_init(void) +{ + int rc; + + rc = platform_driver_register(&mioa701_battery_driver); + if (rc) + printk(KERN_ERR "Could not register mioa701 battery driver\n"); + return rc; +} + +#else +static int __init mioa701_battery_init(void) +{ + return 0; +} +#endif + +/* + * Mio global + */ + +/* Devices */ +#define MIO_PARENT_DEV(var, strname, tparent, pdata) \ +static struct platform_device var = { \ + .name = strname, \ + .id = -1, \ + .dev = { \ + .platform_data = pdata, \ + .parent = tparent, \ + }, \ +}; +#define MIO_SIMPLE_DEV(var, strname, pdata) \ + MIO_PARENT_DEV(var, strname, NULL, pdata) + +MIO_SIMPLE_DEV(mioa701_gpio_keys, "gpio-keys", &mioa701_gpio_keys_data) +MIO_PARENT_DEV(mioa701_backlight, "pwm-backlight", &pxa27x_device_pwm0.dev, + &mioa701_backlight_data); +MIO_SIMPLE_DEV(mioa701_led, "leds-gpio", &gpio_led_info) +MIO_SIMPLE_DEV(pxa2xx_pcm, "pxa2xx-pcm", NULL) +MIO_SIMPLE_DEV(pxa2xx_ac97, "pxa2xx-ac97", NULL) +MIO_PARENT_DEV(mio_wm9713_codec, "wm9713-codec", &pxa2xx_ac97.dev, NULL) +MIO_SIMPLE_DEV(mioa701_sound, "mioa701-wm9713", NULL) +MIO_SIMPLE_DEV(mioa701_board, "mioa701-board", NULL) + +static struct platform_device *devices[] __initdata = { + &mioa701_gpio_keys, + &mioa701_backlight, + &mioa701_led, + &pxa2xx_pcm, + &pxa2xx_ac97, + &mio_wm9713_codec, + &mioa701_sound, + &power_dev, + &strataflash, + &mioa701_board +}; + +static void mioa701_machine_exit(void); + +static void mioa701_poweroff(void) +{ + mioa701_machine_exit(); + gpio_set_value(GPIO18_POWEROFF, 1); +} + +static void mioa701_restart(char c) +{ + mioa701_machine_exit(); + arm_machine_restart(c); +} + +struct gpio_ress global_gpios[] = { + MIO_GPIO_OUT(GPIO9_CHARGE_nEN, 1, "Charger enable"), + MIO_GPIO_OUT(GPIO18_POWEROFF, 0, "Power Off"), + MIO_GPIO_OUT(GPIO87_LCD_POWER, 0, "LCD Power") +}; + +static void __init mioa701_machine_init(void) +{ + PSLR = 0xff100000; /* SYSDEL=125ms, PWRDEL=125ms, PSLR_SL_ROD=1 */ + PCFR = PCFR_DC_EN | PCFR_GPR_EN | PCFR_OPDE; + RTTR = 32768 - 1; /* Reset crazy WinCE value */ + UP2OCR = UP2OCR_HXOE; + + pxa2xx_mfp_config(ARRAY_AND_SIZE(mioa701_pin_config)); + mio_gpio_request(ARRAY_AND_SIZE(global_gpios)); + bootstrap_init(); + set_pxa_fb_info(&mioa701_pxafb_info); + pxa_set_mci_info(&mioa701_mci_info); + pxa_set_keypad_info(&mioa701_keypad_info); + udc_init(); + pm_power_off = mioa701_poweroff; + arm_pm_restart = mioa701_restart; + platform_add_devices(devices, ARRAY_SIZE(devices)); + gsm_init(); + mioa701_battery_init(); +} + +static void mioa701_machine_exit(void) +{ + udc_exit(); + bootstrap_exit(); + gsm_exit(); +} + +MACHINE_START(MIOA701, "MIO A701") + .phys_io = 0x40000000, + .io_pg_offst = (io_p2v(0x40000000) >> 18) & 0xfffc, + .boot_params = 0xa0000100, + .map_io = &pxa_map_io, + .init_irq = &pxa27x_init_irq, + .init_machine = mioa701_machine_init, + .timer = &pxa_timer, +MACHINE_END diff --git a/arch/arm/mach-pxa/mioa701_bootresume.S b/arch/arm/mach-pxa/mioa701_bootresume.S new file mode 100644 index 00000000000..a647693d985 --- /dev/null +++ b/arch/arm/mach-pxa/mioa701_bootresume.S @@ -0,0 +1,36 @@ +/* Bootloader to resume MIO A701 + * + * 2007-1-12 Robert Jarzmik + * + * This code is licenced under the GPLv2. +*/ + +#include <linux/linkage.h> +#include <asm/assembler.h> + +/* + * Note: Yes, part of the following code is located into the .data section. + * This is to allow jumpaddr to be accessed with a relative load + * while we can't rely on any MMU translation. We could have put + * sleep_save_sp in the .text section as well, but some setups might + * insist on it to be truly read-only. + */ + .data +ENTRY(mioa701_bootstrap) +0: + b 1f +ENTRY(mioa701_jumpaddr) + .word 0x40f00008 @ PSPR in no-MMU mode +1: + mov r0, #0xa0000000 @ Don't suppose memory access works + orr r0, r0, #0x00200000 @ even if it's supposed to + mov r1, #0 + str r1, [r0] @ Early disable resume for next boot + ldr r0, mioa701_jumpaddr @ (Murphy's Law) + ldr r0, [r0] + mov pc, r0 +2: + +ENTRY(mioa701_bootstrap_lg) + .data + .word 2b-0b diff --git a/arch/arm/mach-pxa/mp900.c b/arch/arm/mach-pxa/mp900.c new file mode 100644 index 00000000000..8a73814126b --- /dev/null +++ b/arch/arm/mach-pxa/mp900.c @@ -0,0 +1,100 @@ +/* + * linux/arch/arm/mach-pxa/mp900.c + * + * Support for the NEC MobilePro900/C platform + * + * Based on mach-pxa/gumstix.c + * + * 2007, 2008 Kristoffer Ericson <kristoffer.ericson@gmail.com> + * 2007, 2008 Michael Petchkovsky <mkpetch@internode.on.net> + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ + +#include <linux/init.h> +#include <linux/device.h> +#include <linux/platform_device.h> +#include <linux/types.h> +#include <linux/usb/isp116x.h> + +#include <mach/hardware.h> +#include <mach/pxa-regs.h> +#include <asm/mach-types.h> +#include <asm/mach/arch.h> +#include "generic.h" + +static void isp116x_pfm_delay(struct device *dev, int delay) +{ + + /* 400Mhz PXA2 = 2.5ns / instruction */ + + int cyc = delay / 10; + + /* 4 Instructions = 4 x 2.5ns = 10ns */ + __asm__ volatile ("0:\n" + "subs %0, %1, #1\n" + "bge 0b\n" + :"=r" (cyc) + :"0"(cyc) + ); +} + +static struct isp116x_platform_data isp116x_pfm_data = { + .remote_wakeup_enable = 1, + .delay = isp116x_pfm_delay, +}; + +static struct resource isp116x_pfm_resources[] = { + [0] = { + .start = 0x0d000000, + .end = 0x0d000000 + 1, + .flags = IORESOURCE_MEM, + }, + [1] = { + .start = 0x0d000000 + 4, + .end = 0x0d000000 + 5, + .flags = IORESOURCE_MEM, + }, + [2] = { + .start = 61, + .end = 61, + .flags = IORESOURCE_IRQ, + }, +}; + +static struct platform_device mp900c_dummy_device = { + .name = "mp900c_dummy", + .id = -1, +}; + +static struct platform_device mp900c_usb = { + .name = "isp116x-hcd", + .num_resources = ARRAY_SIZE(isp116x_pfm_resources), + .resource = isp116x_pfm_resources, + .dev.platform_data = &isp116x_pfm_data, +}; + +static struct platform_device *devices[] __initdata = { + &mp900c_dummy_device, + &mp900c_usb, +}; + +static void __init mp900c_init(void) +{ + printk(KERN_INFO "MobilePro 900/C machine init\n"); + platform_add_devices(devices, ARRAY_SIZE(devices)); +} + +/* Maintainer - Michael Petchkovsky <mkpetch@internode.on.net> */ +MACHINE_START(NEC_MP900, "MobilePro900/C") + .phys_io = 0x40000000, + .boot_params = 0xa0220100, + .io_pg_offst = (io_p2v(0x40000000) >> 18) & 0xfffc, + .timer = &pxa_timer, + .map_io = pxa_map_io, + .init_irq = pxa25x_init_irq, + .init_machine = mp900c_init, +MACHINE_END + diff --git a/arch/arm/mach-pxa/palmtx.c b/arch/arm/mach-pxa/palmtx.c new file mode 100644 index 00000000000..4447711c9fc --- /dev/null +++ b/arch/arm/mach-pxa/palmtx.c @@ -0,0 +1,436 @@ +/* + * Hardware definitions for PalmTX + * + * Author: Marek Vasut <marek.vasut@gmail.com> + * + * Based on work of: + * Alex Osborne <ato@meshy.org> + * Cristiano P. <cristianop@users.sourceforge.net> + * Jan Herman <2hp@seznam.cz> + * Michal Hrusecky + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + * + * (find more info at www.hackndev.com) + * + */ + +#include <linux/platform_device.h> +#include <linux/delay.h> +#include <linux/irq.h> +#include <linux/gpio_keys.h> +#include <linux/input.h> +#include <linux/pda_power.h> +#include <linux/pwm_backlight.h> +#include <linux/gpio.h> +#include <linux/wm97xx_batt.h> +#include <linux/power_supply.h> + +#include <asm/mach-types.h> +#include <asm/mach/arch.h> +#include <asm/mach/map.h> + +#include <mach/audio.h> +#include <mach/palmtx.h> +#include <mach/mmc.h> +#include <mach/pxafb.h> +#include <mach/pxa-regs.h> +#include <mach/mfp-pxa27x.h> +#include <mach/irda.h> +#include <mach/pxa27x_keypad.h> +#include <mach/udc.h> + +#include "generic.h" +#include "devices.h" + +/****************************************************************************** + * Pin configuration + ******************************************************************************/ +static unsigned long palmtx_pin_config[] __initdata = { + /* MMC */ + GPIO32_MMC_CLK, + GPIO92_MMC_DAT_0, + GPIO109_MMC_DAT_1, + GPIO110_MMC_DAT_2, + GPIO111_MMC_DAT_3, + GPIO112_MMC_CMD, + + /* AC97 */ + GPIO28_AC97_BITCLK, + GPIO29_AC97_SDATA_IN_0, + GPIO30_AC97_SDATA_OUT, + GPIO31_AC97_SYNC, + + /* IrDA */ + GPIO46_FICP_RXD, + GPIO47_FICP_TXD, + + /* PWM */ + GPIO16_PWM0_OUT, + + /* USB */ + GPIO13_GPIO, + + /* PCMCIA */ + GPIO48_nPOE, + GPIO49_nPWE, + GPIO50_nPIOR, + GPIO51_nPIOW, + GPIO85_nPCE_1, + GPIO54_nPCE_2, + GPIO79_PSKTSEL, + GPIO55_nPREG, + GPIO56_nPWAIT, + GPIO57_nIOIS16, +}; + +/****************************************************************************** + * SD/MMC card controller + ******************************************************************************/ +static int palmtx_mci_init(struct device *dev, irq_handler_t palmtx_detect_int, + void *data) +{ + int err = 0; + + /* Setup an interrupt for detecting card insert/remove events */ + err = request_irq(IRQ_GPIO_PALMTX_SD_DETECT_N, palmtx_detect_int, + IRQF_DISABLED | IRQF_SAMPLE_RANDOM | + IRQF_TRIGGER_FALLING | IRQF_TRIGGER_RISING, + "SD/MMC card detect", data); + if (err) { + printk(KERN_ERR "%s: cannot request SD/MMC card detect IRQ\n", + __func__); + return err; + } + + err = gpio_request(GPIO_NR_PALMTX_SD_POWER, "SD_POWER"); + if (err) + goto pwr_err; + + err = gpio_request(GPIO_NR_PALMTX_SD_READONLY, "SD_READONLY"); + if (err) + goto ro_err; + + printk(KERN_DEBUG "%s: irq registered\n", __func__); + + return 0; + +ro_err: + gpio_free(GPIO_NR_PALMTX_SD_POWER); +pwr_err: + free_irq(IRQ_GPIO_PALMTX_SD_DETECT_N, data); + return err; +} + +static void palmtx_mci_exit(struct device *dev, void *data) +{ + gpio_free(GPIO_NR_PALMTX_SD_READONLY); + gpio_free(GPIO_NR_PALMTX_SD_POWER); + free_irq(IRQ_GPIO_PALMTX_SD_DETECT_N, data); +} + +static void palmtx_mci_power(struct device *dev, unsigned int vdd) +{ + struct pxamci_platform_data *p_d = dev->platform_data; + gpio_set_value(GPIO_NR_PALMTX_SD_POWER, p_d->ocr_mask & (1 << vdd)); +} + +static int palmtx_mci_get_ro(struct device *dev) +{ + return gpio_get_value(GPIO_NR_PALMTX_SD_READONLY); +} + +static struct pxamci_platform_data palmtx_mci_platform_data = { + .ocr_mask = MMC_VDD_32_33 | MMC_VDD_33_34, + .setpower = palmtx_mci_power, + .get_ro = palmtx_mci_get_ro, + .init = palmtx_mci_init, + .exit = palmtx_mci_exit, +}; + +/****************************************************************************** + * GPIO keyboard + ******************************************************************************/ +static unsigned int palmtx_matrix_keys[] = { + KEY(0, 0, KEY_POWER), + KEY(0, 1, KEY_F1), + KEY(0, 2, KEY_ENTER), + + KEY(1, 0, KEY_F2), + KEY(1, 1, KEY_F3), + KEY(1, 2, KEY_F4), + + KEY(2, 0, KEY_UP), + KEY(2, 2, KEY_DOWN), + + KEY(3, 0, KEY_RIGHT), + KEY(3, 2, KEY_LEFT), + +}; + +static struct pxa27x_keypad_platform_data palmtx_keypad_platform_data = { + .matrix_key_rows = 4, + .matrix_key_cols = 3, + .matrix_key_map = palmtx_matrix_keys, + .matrix_key_map_size = ARRAY_SIZE(palmtx_matrix_keys), + + .debounce_interval = 30, +}; + +/****************************************************************************** + * GPIO keys + ******************************************************************************/ +static struct gpio_keys_button palmtx_pxa_buttons[] = { + {KEY_F8, GPIO_NR_PALMTX_HOTSYNC_BUTTON_N, 1, "HotSync Button" }, +}; + +static struct gpio_keys_platform_data palmtx_pxa_keys_data = { + .buttons = palmtx_pxa_buttons, + .nbuttons = ARRAY_SIZE(palmtx_pxa_buttons), +}; + +static struct platform_device palmtx_pxa_keys = { + .name = "gpio-keys", + .id = -1, + .dev = { + .platform_data = &palmtx_pxa_keys_data, + }, +}; + +/****************************************************************************** + * Backlight + ******************************************************************************/ +static int palmtx_backlight_init(struct device *dev) +{ + int ret; + + ret = gpio_request(GPIO_NR_PALMTX_BL_POWER, "BL POWER"); + if (ret) + goto err; + ret = gpio_request(GPIO_NR_PALMTX_LCD_POWER, "LCD POWER"); + if (ret) + goto err2; + + return 0; +err2: + gpio_free(GPIO_NR_PALMTX_BL_POWER); +err: + return ret; +} + +static int palmtx_backlight_notify(int brightness) +{ + gpio_set_value(GPIO_NR_PALMTX_BL_POWER, brightness); + gpio_set_value(GPIO_NR_PALMTX_LCD_POWER, brightness); + return brightness; +} + +static void palmtx_backlight_exit(struct device *dev) +{ + gpio_free(GPIO_NR_PALMTX_BL_POWER); + gpio_free(GPIO_NR_PALMTX_LCD_POWER); +} + +static struct platform_pwm_backlight_data palmtx_backlight_data = { + .pwm_id = 0, + .max_brightness = PALMTX_MAX_INTENSITY, + .dft_brightness = PALMTX_MAX_INTENSITY, + .pwm_period_ns = PALMTX_PERIOD_NS, + .init = palmtx_backlight_init, + .notify = palmtx_backlight_notify, + .exit = palmtx_backlight_exit, +}; + +static struct platform_device palmtx_backlight = { + .name = "pwm-backlight", + .dev = { + .parent = &pxa27x_device_pwm0.dev, + .platform_data = &palmtx_backlight_data, + }, +}; + +/****************************************************************************** + * IrDA + ******************************************************************************/ +static void palmtx_irda_transceiver_mode(struct device *dev, int mode) +{ + gpio_set_value(GPIO_NR_PALMTX_IR_DISABLE, mode & IR_OFF); + pxa2xx_transceiver_mode(dev, mode); +} + +static struct pxaficp_platform_data palmtx_ficp_platform_data = { + .transceiver_cap = IR_SIRMODE | IR_FIRMODE | IR_OFF, + .transceiver_mode = palmtx_irda_transceiver_mode, +}; + +/****************************************************************************** + * UDC + ******************************************************************************/ +static void palmtx_udc_command(int cmd) +{ + gpio_set_value(GPIO_NR_PALMTX_USB_POWER, !cmd); + udelay(50); + gpio_set_value(GPIO_NR_PALMTX_USB_PULLUP, !cmd); +} + +static struct pxa2xx_udc_mach_info palmtx_udc_info __initdata = { + .gpio_vbus = GPIO_NR_PALMTX_USB_DETECT_N, + .gpio_vbus_inverted = 1, + .udc_command = palmtx_udc_command, +}; + +/****************************************************************************** + * Power supply + ******************************************************************************/ +static int power_supply_init(struct device *dev) +{ + int ret; + + ret = gpio_request(GPIO_NR_PALMTX_POWER_DETECT, "CABLE_STATE_AC"); + if (ret) + goto err_cs_ac; + + ret = gpio_request(GPIO_NR_PALMTX_USB_DETECT_N, "CABLE_STATE_USB"); + if (ret) + goto err_cs_usb; + + return 0; + +err_cs_usb: + gpio_free(GPIO_NR_PALMTX_POWER_DETECT); +err_cs_ac: + return ret; +} + +static int palmtx_is_ac_online(void) +{ + return gpio_get_value(GPIO_NR_PALMTX_POWER_DETECT); +} + +static int palmtx_is_usb_online(void) +{ + return !gpio_get_value(GPIO_NR_PALMTX_USB_DETECT_N); +} + +static void power_supply_exit(struct device *dev) +{ + gpio_free(GPIO_NR_PALMTX_USB_DETECT_N); + gpio_free(GPIO_NR_PALMTX_POWER_DETECT); +} + +static char *palmtx_supplicants[] = { + "main-battery", +}; + +static struct pda_power_pdata power_supply_info = { + .init = power_supply_init, + .is_ac_online = palmtx_is_ac_online, + .is_usb_online = palmtx_is_usb_online, + .exit = power_supply_exit, + .supplied_to = palmtx_supplicants, + .num_supplicants = ARRAY_SIZE(palmtx_supplicants), +}; + +static struct platform_device power_supply = { + .name = "pda-power", + .id = -1, + .dev = { + .platform_data = &power_supply_info, + }, +}; + +/****************************************************************************** + * WM97xx battery + ******************************************************************************/ +static struct wm97xx_batt_info wm97xx_batt_pdata = { + .batt_aux = WM97XX_AUX_ID3, + .temp_aux = WM97XX_AUX_ID2, + .charge_gpio = -1, + .max_voltage = PALMTX_BAT_MAX_VOLTAGE, + .min_voltage = PALMTX_BAT_MIN_VOLTAGE, + .batt_mult = 1000, + .batt_div = 414, + .temp_mult = 1, + .temp_div = 1, + .batt_tech = POWER_SUPPLY_TECHNOLOGY_LIPO, + .batt_name = "main-batt", +}; + +/****************************************************************************** + * Framebuffer + ******************************************************************************/ +static struct pxafb_mode_info palmtx_lcd_modes[] = { +{ + .pixclock = 57692, + .xres = 320, + .yres = 480, + .bpp = 16, + + .left_margin = 32, + .right_margin = 1, + .upper_margin = 7, + .lower_margin = 1, + + .hsync_len = 4, + .vsync_len = 1, +}, +}; + +static struct pxafb_mach_info palmtx_lcd_screen = { + .modes = palmtx_lcd_modes, + .num_modes = ARRAY_SIZE(palmtx_lcd_modes), + .lcd_conn = LCD_COLOR_TFT_16BPP | LCD_PCLK_EDGE_FALL, +}; + +/****************************************************************************** + * Machine init + ******************************************************************************/ +static struct platform_device *devices[] __initdata = { +#if defined(CONFIG_KEYBOARD_GPIO) || defined(CONFIG_KEYBOARD_GPIO_MODULE) + &palmtx_pxa_keys, +#endif + &palmtx_backlight, + &power_supply, +}; + +static struct map_desc palmtx_io_desc[] __initdata = { +{ + .virtual = PALMTX_PCMCIA_VIRT, + .pfn = __phys_to_pfn(PALMTX_PCMCIA_PHYS), + .length = PALMTX_PCMCIA_SIZE, + .type = MT_DEVICE +}, +}; + +static void __init palmtx_map_io(void) +{ + pxa_map_io(); + iotable_init(palmtx_io_desc, ARRAY_SIZE(palmtx_io_desc)); +} + +static void __init palmtx_init(void) +{ + pxa2xx_mfp_config(ARRAY_AND_SIZE(palmtx_pin_config)); + + set_pxa_fb_info(&palmtx_lcd_screen); + pxa_set_mci_info(&palmtx_mci_platform_data); + pxa_set_udc_info(&palmtx_udc_info); + pxa_set_ac97_info(NULL); + pxa_set_ficp_info(&palmtx_ficp_platform_data); + pxa_set_keypad_info(&palmtx_keypad_platform_data); + wm97xx_bat_set_pdata(&wm97xx_batt_pdata); + + platform_add_devices(devices, ARRAY_SIZE(devices)); +} + +MACHINE_START(PALMTX, "Palm T|X") + .phys_io = PALMTX_PHYS_IO_START, + .io_pg_offst = io_p2v(0x40000000), + .boot_params = 0xa0000100, + .map_io = palmtx_map_io, + .init_irq = pxa27x_init_irq, + .timer = &pxa_timer, + .init_machine = palmtx_init +MACHINE_END diff --git a/arch/arm/mach-pxa/palmz72.c b/arch/arm/mach-pxa/palmz72.c new file mode 100644 index 00000000000..2f730da3bba --- /dev/null +++ b/arch/arm/mach-pxa/palmz72.c @@ -0,0 +1,554 @@ +/* + * Hardware definitions for Palm Zire72 + * + * Authors: + * Vladimir "Farcaller" Pouzanov <farcaller@gmail.com> + * Sergey Lapin <slapin@ossfans.org> + * Alex Osborne <bobofdoom@gmail.com> + * Jan Herman <2hp@seznam.cz> + * + * Rewrite for mainline: + * Marek Vasut <marek.vasut@gmail.com> + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + * + * (find more info at www.hackndev.com) + * + */ + +#include <linux/platform_device.h> +#include <linux/sysdev.h> +#include <linux/delay.h> +#include <linux/irq.h> +#include <linux/gpio_keys.h> +#include <linux/input.h> +#include <linux/pda_power.h> +#include <linux/pwm_backlight.h> +#include <linux/gpio.h> +#include <linux/power_supply.h> + +#include <asm/mach-types.h> +#include <asm/mach/arch.h> +#include <asm/mach/map.h> + +#include <mach/audio.h> +#include <mach/palmz72.h> +#include <mach/mmc.h> +#include <mach/pxafb.h> +#include <mach/pxa-regs.h> +#include <mach/pxa2xx-regs.h> +#include <mach/mfp-pxa27x.h> +#include <mach/irda.h> +#include <mach/pxa27x_keypad.h> +#include <mach/udc.h> +#include <mach/pm.h> + +#include "generic.h" +#include "devices.h" + +/****************************************************************************** + * Pin configuration + ******************************************************************************/ +static unsigned long palmz72_pin_config[] __initdata = { + /* MMC */ + GPIO32_MMC_CLK, + GPIO92_MMC_DAT_0, + GPIO109_MMC_DAT_1, + GPIO110_MMC_DAT_2, + GPIO111_MMC_DAT_3, + GPIO112_MMC_CMD, + GPIO14_GPIO, /* SD detect */ + GPIO115_GPIO, /* SD RO */ + GPIO98_GPIO, /* SD power */ + + /* AC97 */ + GPIO28_AC97_BITCLK, + GPIO29_AC97_SDATA_IN_0, + GPIO30_AC97_SDATA_OUT, + GPIO31_AC97_SYNC, + + /* IrDA */ + GPIO49_GPIO, /* ir disable */ + GPIO46_FICP_RXD, + GPIO47_FICP_TXD, + + /* PWM */ + GPIO16_PWM0_OUT, + + /* USB */ + GPIO15_GPIO, /* usb detect */ + GPIO12_GPIO, /* usb pullup */ + GPIO95_GPIO, /* usb power */ + + /* Matrix keypad */ + GPIO100_KP_MKIN_0 | WAKEUP_ON_LEVEL_HIGH, + GPIO101_KP_MKIN_1 | WAKEUP_ON_LEVEL_HIGH, + GPIO102_KP_MKIN_2 | WAKEUP_ON_LEVEL_HIGH, + GPIO97_KP_MKIN_3 | WAKEUP_ON_LEVEL_HIGH, + GPIO103_KP_MKOUT_0, + GPIO104_KP_MKOUT_1, + GPIO105_KP_MKOUT_2, + + /* LCD */ + GPIO58_LCD_LDD_0, + GPIO59_LCD_LDD_1, + GPIO60_LCD_LDD_2, + GPIO61_LCD_LDD_3, + GPIO62_LCD_LDD_4, + GPIO63_LCD_LDD_5, + GPIO64_LCD_LDD_6, + GPIO65_LCD_LDD_7, + GPIO66_LCD_LDD_8, + GPIO67_LCD_LDD_9, + GPIO68_LCD_LDD_10, + GPIO69_LCD_LDD_11, + GPIO70_LCD_LDD_12, + GPIO71_LCD_LDD_13, + GPIO72_LCD_LDD_14, + GPIO73_LCD_LDD_15, + GPIO74_LCD_FCLK, + GPIO75_LCD_LCLK, + GPIO76_LCD_PCLK, + GPIO77_LCD_BIAS, + GPIO20_GPIO, /* bl power */ + GPIO21_GPIO, /* LCD border switch */ + GPIO22_GPIO, /* LCD border color */ + GPIO96_GPIO, /* lcd power */ + + /* Misc. */ + GPIO0_GPIO | WAKEUP_ON_LEVEL_HIGH, /* power detect */ + GPIO88_GPIO, /* green led */ + GPIO27_GPIO, /* WM9712 IRQ */ +}; + +/****************************************************************************** + * SD/MMC card controller + ******************************************************************************/ +static int palmz72_mci_init(struct device *dev, + irq_handler_t palmz72_detect_int, void *data) +{ + int err = 0; + + /* Setup an interrupt for detecting card insert/remove events */ + err = gpio_request(GPIO_NR_PALMZ72_SD_DETECT_N, "SD IRQ"); + if (err) + goto err; + err = gpio_direction_input(GPIO_NR_PALMZ72_SD_DETECT_N); + if (err) + goto err2; + err = request_irq(gpio_to_irq(GPIO_NR_PALMZ72_SD_DETECT_N), + palmz72_detect_int, IRQF_DISABLED | IRQF_SAMPLE_RANDOM | + IRQF_TRIGGER_FALLING | IRQF_TRIGGER_RISING, + "SD/MMC card detect", data); + if (err) { + printk(KERN_ERR "%s: cannot request SD/MMC card detect IRQ\n", + __func__); + goto err2; + } + + /* SD_POWER is not actually power, but it is more like chip + * select, i.e. it is inverted */ + + err = gpio_request(GPIO_NR_PALMZ72_SD_POWER_N, "SD_POWER"); + if (err) + goto err3; + err = gpio_direction_output(GPIO_NR_PALMZ72_SD_POWER_N, 0); + if (err) + goto err4; + err = gpio_request(GPIO_NR_PALMZ72_SD_RO, "SD_RO"); + if (err) + goto err4; + err = gpio_direction_input(GPIO_NR_PALMZ72_SD_RO); + if (err) + goto err5; + + printk(KERN_DEBUG "%s: irq registered\n", __func__); + + return 0; + +err5: + gpio_free(GPIO_NR_PALMZ72_SD_RO); +err4: + gpio_free(GPIO_NR_PALMZ72_SD_POWER_N); +err3: + free_irq(gpio_to_irq(GPIO_NR_PALMZ72_SD_DETECT_N), data); +err2: + gpio_free(GPIO_NR_PALMZ72_SD_DETECT_N); +err: + return err; +} + +static void palmz72_mci_exit(struct device *dev, void *data) +{ + gpio_free(GPIO_NR_PALMZ72_SD_POWER_N); + free_irq(gpio_to_irq(GPIO_NR_PALMZ72_SD_DETECT_N), data); + gpio_free(GPIO_NR_PALMZ72_SD_DETECT_N); + gpio_free(GPIO_NR_PALMZ72_SD_RO); +} + +static void palmz72_mci_power(struct device *dev, unsigned int vdd) +{ + struct pxamci_platform_data *p_d = dev->platform_data; + if (p_d->ocr_mask & (1 << vdd)) + gpio_set_value(GPIO_NR_PALMZ72_SD_POWER_N, 0); + else + gpio_set_value(GPIO_NR_PALMZ72_SD_POWER_N, 1); +} + +static int palmz72_mci_ro(struct device *dev) +{ + return gpio_get_value(GPIO_NR_PALMZ72_SD_RO); +} + +static struct pxamci_platform_data palmz72_mci_platform_data = { + .ocr_mask = MMC_VDD_32_33 | MMC_VDD_33_34, + .setpower = palmz72_mci_power, + .get_ro = palmz72_mci_ro, + .init = palmz72_mci_init, + .exit = palmz72_mci_exit, +}; + +/****************************************************************************** + * GPIO keyboard + ******************************************************************************/ +static unsigned int palmz72_matrix_keys[] = { + KEY(0, 0, KEY_POWER), + KEY(0, 1, KEY_F1), + KEY(0, 2, KEY_ENTER), + + KEY(1, 0, KEY_F2), + KEY(1, 1, KEY_F3), + KEY(1, 2, KEY_F4), + + KEY(2, 0, KEY_UP), + KEY(2, 2, KEY_DOWN), + + KEY(3, 0, KEY_RIGHT), + KEY(3, 2, KEY_LEFT), +}; + +static struct pxa27x_keypad_platform_data palmz72_keypad_platform_data = { + .matrix_key_rows = 4, + .matrix_key_cols = 3, + .matrix_key_map = palmz72_matrix_keys, + .matrix_key_map_size = ARRAY_SIZE(palmz72_matrix_keys), + + .debounce_interval = 30, +}; + +/****************************************************************************** + * Backlight + ******************************************************************************/ +static int palmz72_backlight_init(struct device *dev) +{ + int ret; + + ret = gpio_request(GPIO_NR_PALMZ72_BL_POWER, "BL POWER"); + if (ret) + goto err; + ret = gpio_direction_output(GPIO_NR_PALMZ72_BL_POWER, 0); + if (ret) + goto err2; + ret = gpio_request(GPIO_NR_PALMZ72_LCD_POWER, "LCD POWER"); + if (ret) + goto err2; + ret = gpio_direction_output(GPIO_NR_PALMZ72_LCD_POWER, 0); + if (ret) + goto err3; + + return 0; +err3: + gpio_free(GPIO_NR_PALMZ72_LCD_POWER); +err2: + gpio_free(GPIO_NR_PALMZ72_BL_POWER); +err: + return ret; +} + +static int palmz72_backlight_notify(int brightness) +{ + gpio_set_value(GPIO_NR_PALMZ72_BL_POWER, brightness); + gpio_set_value(GPIO_NR_PALMZ72_LCD_POWER, brightness); + return brightness; +} + +static void palmz72_backlight_exit(struct device *dev) +{ + gpio_free(GPIO_NR_PALMZ72_BL_POWER); + gpio_free(GPIO_NR_PALMZ72_LCD_POWER); +} + +static struct platform_pwm_backlight_data palmz72_backlight_data = { + .pwm_id = 0, + .max_brightness = PALMZ72_MAX_INTENSITY, + .dft_brightness = PALMZ72_MAX_INTENSITY, + .pwm_period_ns = PALMZ72_PERIOD_NS, + .init = palmz72_backlight_init, + .notify = palmz72_backlight_notify, + .exit = palmz72_backlight_exit, +}; + +static struct platform_device palmz72_backlight = { + .name = "pwm-backlight", + .dev = { + .parent = &pxa27x_device_pwm0.dev, + .platform_data = &palmz72_backlight_data, + }, +}; + +/****************************************************************************** + * IrDA + ******************************************************************************/ +static int palmz72_irda_startup(struct device *dev) +{ + int err; + err = gpio_request(GPIO_NR_PALMZ72_IR_DISABLE, "IR DISABLE"); + if (err) + goto err; + err = gpio_direction_output(GPIO_NR_PALMZ72_IR_DISABLE, 1); + if (err) + gpio_free(GPIO_NR_PALMZ72_IR_DISABLE); +err: + return err; +} + +static void palmz72_irda_shutdown(struct device *dev) +{ + gpio_free(GPIO_NR_PALMZ72_IR_DISABLE); +} + +static void palmz72_irda_transceiver_mode(struct device *dev, int mode) +{ + gpio_set_value(GPIO_NR_PALMZ72_IR_DISABLE, mode & IR_OFF); + pxa2xx_transceiver_mode(dev, mode); +} + +static struct pxaficp_platform_data palmz72_ficp_platform_data = { + .startup = palmz72_irda_startup, + .shutdown = palmz72_irda_shutdown, + .transceiver_cap = IR_SIRMODE | IR_OFF, + .transceiver_mode = palmz72_irda_transceiver_mode, +}; + +/****************************************************************************** + * LEDs + ******************************************************************************/ +static struct gpio_led gpio_leds[] = { + { + .name = "palmz72:green:led", + .default_trigger = "none", + .gpio = GPIO_NR_PALMZ72_LED_GREEN, + }, +}; + +static struct gpio_led_platform_data gpio_led_info = { + .leds = gpio_leds, + .num_leds = ARRAY_SIZE(gpio_leds), +}; + +static struct platform_device palmz72_leds = { + .name = "leds-gpio", + .id = -1, + .dev = { + .platform_data = &gpio_led_info, + } +}; + +/****************************************************************************** + * Power supply + ******************************************************************************/ +static int power_supply_init(struct device *dev) +{ + int ret; + + ret = gpio_request(GPIO_NR_PALMZ72_POWER_DETECT, "CABLE_STATE_AC"); + if (ret) + goto err1; + ret = gpio_direction_input(GPIO_NR_PALMZ72_POWER_DETECT); + if (ret) + goto err2; + + ret = gpio_request(GPIO_NR_PALMZ72_USB_DETECT_N, "CABLE_STATE_USB"); + if (ret) + goto err2; + ret = gpio_direction_input(GPIO_NR_PALMZ72_USB_DETECT_N); + if (ret) + goto err3; + + return 0; +err3: + gpio_free(GPIO_NR_PALMZ72_USB_DETECT_N); +err2: + gpio_free(GPIO_NR_PALMZ72_POWER_DETECT); +err1: + return ret; +} + +static int palmz72_is_ac_online(void) +{ + return gpio_get_value(GPIO_NR_PALMZ72_POWER_DETECT); +} + +static int palmz72_is_usb_online(void) +{ + return !gpio_get_value(GPIO_NR_PALMZ72_USB_DETECT_N); +} + +static void power_supply_exit(struct device *dev) +{ + gpio_free(GPIO_NR_PALMZ72_USB_DETECT_N); + gpio_free(GPIO_NR_PALMZ72_POWER_DETECT); +} + +static char *palmz72_supplicants[] = { + "main-battery", +}; + +static struct pda_power_pdata power_supply_info = { + .init = power_supply_init, + .is_ac_online = palmz72_is_ac_online, + .is_usb_online = palmz72_is_usb_online, + .exit = power_supply_exit, + .supplied_to = palmz72_supplicants, + .num_supplicants = ARRAY_SIZE(palmz72_supplicants), +}; + +static struct platform_device power_supply = { + .name = "pda-power", + .id = -1, + .dev = { + .platform_data = &power_supply_info, + }, +}; + +/****************************************************************************** + * Framebuffer + ******************************************************************************/ +static struct pxafb_mode_info palmz72_lcd_modes[] = { +{ + .pixclock = 115384, + .xres = 320, + .yres = 320, + .bpp = 16, + + .left_margin = 27, + .right_margin = 7, + .upper_margin = 7, + .lower_margin = 8, + + .hsync_len = 6, + .vsync_len = 1, +}, +}; + +static struct pxafb_mach_info palmz72_lcd_screen = { + .modes = palmz72_lcd_modes, + .num_modes = ARRAY_SIZE(palmz72_lcd_modes), + .lcd_conn = LCD_COLOR_TFT_16BPP | LCD_PCLK_EDGE_FALL, +}; + +#ifdef CONFIG_PM + +/* We have some black magic here + * PalmOS ROM on recover expects special struct physical address + * to be transferred via PSPR. Using this struct PalmOS restores + * its state after sleep. As for Linux, we need to setup it the + * same way. More than that, PalmOS ROM changes some values in memory. + * For now only one location is found, which needs special treatment. + * Thanks to Alex Osborne, Andrzej Zaborowski, and lots of other people + * for reading backtraces for me :) + */ + +#define PALMZ72_SAVE_DWORD ((unsigned long *)0xc0000050) + +static struct palmz72_resume_info palmz72_resume_info = { + .magic0 = 0xb4e6, + .magic1 = 1, + + /* reset state, MMU off etc */ + .arm_control = 0, + .aux_control = 0, + .ttb = 0, + .domain_access = 0, + .process_id = 0, +}; + +static unsigned long store_ptr; + +/* sys_device for Palm Zire 72 PM */ + +static int palmz72_pm_suspend(struct sys_device *dev, pm_message_t msg) +{ + /* setup the resume_info struct for the original bootloader */ + palmz72_resume_info.resume_addr = (u32) pxa_cpu_resume; + + /* Storing memory touched by ROM */ + store_ptr = *PALMZ72_SAVE_DWORD; + + /* Setting PSPR to a proper value */ + PSPR = virt_to_phys(&palmz72_resume_info); + + return 0; +} + +static int palmz72_pm_resume(struct sys_device *dev) +{ + *PALMZ72_SAVE_DWORD = store_ptr; + return 0; +} + +static struct sysdev_class palmz72_pm_sysclass = { + .name = "palmz72_pm", + .suspend = palmz72_pm_suspend, + .resume = palmz72_pm_resume, +}; + +static struct sys_device palmz72_pm_device = { + .cls = &palmz72_pm_sysclass, +}; + +static int __init palmz72_pm_init(void) +{ + int ret = -ENODEV; + if (machine_is_palmz72()) { + ret = sysdev_class_register(&palmz72_pm_sysclass); + if (ret == 0) + ret = sysdev_register(&palmz72_pm_device); + } + return ret; +} + +device_initcall(palmz72_pm_init); +#endif + +/****************************************************************************** + * Machine init + ******************************************************************************/ +static struct platform_device *devices[] __initdata = { + &palmz72_backlight, + &palmz72_leds, + &power_supply, +}; + +static void __init palmz72_init(void) +{ + pxa2xx_mfp_config(ARRAY_AND_SIZE(palmz72_pin_config)); + set_pxa_fb_info(&palmz72_lcd_screen); + pxa_set_mci_info(&palmz72_mci_platform_data); + pxa_set_ac97_info(NULL); + pxa_set_ficp_info(&palmz72_ficp_platform_data); + pxa_set_keypad_info(&palmz72_keypad_platform_data); + platform_add_devices(devices, ARRAY_SIZE(devices)); +} + +MACHINE_START(PALMZ72, "Palm Zire72") + .phys_io = 0x40000000, + .io_pg_offst = io_p2v(0x40000000), + .boot_params = 0xa0000100, + .map_io = pxa_map_io, + .init_irq = pxa27x_init_irq, + .timer = &pxa_timer, + .init_machine = palmz72_init +MACHINE_END diff --git a/arch/arm/mach-pxa/pcm027.c b/arch/arm/mach-pxa/pcm027.c index 3b945eb0aee..36135a02fdc 100644 --- a/arch/arm/mach-pxa/pcm027.c +++ b/arch/arm/mach-pxa/pcm027.c @@ -24,15 +24,17 @@ #include <linux/platform_device.h> #include <linux/mtd/physmap.h> #include <linux/spi/spi.h> +#include <linux/spi/max7301.h> #include <linux/leds.h> + #include <asm/mach-types.h> #include <asm/mach/arch.h> -#include <asm/arch/hardware.h> -#include <asm/arch/pxa-regs.h> -#include <asm/arch/pxa2xx-gpio.h> -#include <asm/arch/pxa2xx-regs.h> -#include <asm/arch/pxa2xx_spi.h> -#include <asm/arch/pcm027.h> +#include <mach/hardware.h> +#include <mach/pxa-regs.h> +#include <mach/mfp-pxa27x.h> +#include <mach/pxa2xx-regs.h> +#include <mach/pxa2xx_spi.h> +#include <mach/pcm027.h> #include "generic.h" /* @@ -84,6 +86,28 @@ * *) CPU internal use only */ +static unsigned long pcm027_pin_config[] __initdata = { + /* Chip Selects */ + GPIO20_nSDCS_2, + GPIO21_nSDCS_3, + GPIO15_nCS_1, + GPIO78_nCS_2, + GPIO80_nCS_4, + GPIO33_nCS_5, /* Ethernet */ + + /* I2C */ + GPIO117_I2C_SCL, + GPIO118_I2C_SDA, + + /* GPIO */ + GPIO52_GPIO, /* IRQ from network controller */ +#ifdef CONFIG_LEDS_GPIO + GPIO90_GPIO, /* PCM027_LED_CPU */ + GPIO91_GPIO, /* PCM027_LED_HEART_BEAT */ +#endif + GPIO114_GPIO, /* IRQ from CAN controller */ +}; + /* * SMC91x network controller specific stuff */ @@ -108,6 +132,32 @@ static struct platform_device smc91x_device = { .resource = smc91x_resources, }; +/* + * SPI host and devices + */ +static struct pxa2xx_spi_master pxa_ssp_master_info = { + .num_chipselect = 1, +}; + +static struct max7301_platform_data max7301_info = { + .base = -1, +}; + +/* bus_num must match id in pxa2xx_set_spi_info() call */ +static struct spi_board_info spi_board_info[] __initdata = { + { + .modalias = "max7301", + .platform_data = &max7301_info, + .max_speed_hz = 13000000, + .bus_num = 1, + .chip_select = 0, + .mode = SPI_MODE_0, + }, +}; + +/* + * NOR flash + */ static struct physmap_flash_data pcm027_flash_data = { .width = 4, }; @@ -178,18 +228,17 @@ static void __init pcm027_init(void) */ ARB_CNTRL = ARB_CORE_PARK | 0x234; - platform_add_devices(devices, ARRAY_SIZE(devices)); + pxa2xx_mfp_config(pcm027_pin_config, ARRAY_SIZE(pcm027_pin_config)); - /* LEDs (on demand only) */ -#ifdef CONFIG_LEDS_GPIO - pxa_gpio_mode(PCM027_LED_CPU | GPIO_OUT); - pxa_gpio_mode(PCM027_LED_HEARD_BEAT | GPIO_OUT); -#endif /* CONFIG_LEDS_GPIO */ + platform_add_devices(devices, ARRAY_SIZE(devices)); /* at last call the baseboard to initialize itself */ #ifdef CONFIG_MACH_PCM990_BASEBOARD pcm990_baseboard_init(); #endif + + pxa2xx_set_spi_info(1, &pxa_ssp_master_info); + spi_register_board_info(spi_board_info, ARRAY_SIZE(spi_board_info)); } static void __init pcm027_map_io(void) diff --git a/arch/arm/mach-pxa/pcm990-baseboard.c b/arch/arm/mach-pxa/pcm990-baseboard.c index 49d951db0f3..f601425f1b1 100644 --- a/arch/arm/mach-pxa/pcm990-baseboard.c +++ b/arch/arm/mach-pxa/pcm990-baseboard.c @@ -22,23 +22,130 @@ #include <linux/irq.h> #include <linux/platform_device.h> -#include <linux/ide.h> #include <linux/i2c.h> +#include <linux/pwm_backlight.h> #include <media/soc_camera.h> #include <asm/gpio.h> -#include <asm/arch/i2c.h> -#include <asm/arch/camera.h> +#include <mach/i2c.h> +#include <mach/camera.h> #include <asm/mach/map.h> -#include <asm/arch/pxa-regs.h> -#include <asm/arch/pxa2xx-gpio.h> -#include <asm/arch/mmc.h> -#include <asm/arch/ohci.h> -#include <asm/arch/pcm990_baseboard.h> +#include <mach/pxa-regs.h> +#include <mach/audio.h> +#include <mach/mmc.h> +#include <mach/ohci.h> +#include <mach/pcm990_baseboard.h> +#include <mach/pxafb.h> +#include <mach/mfp-pxa27x.h> + +#include "devices.h" +#include "generic.h" + +static unsigned long pcm990_pin_config[] __initdata = { + /* MMC */ + GPIO32_MMC_CLK, + GPIO112_MMC_CMD, + GPIO92_MMC_DAT_0, + GPIO109_MMC_DAT_1, + GPIO110_MMC_DAT_2, + GPIO111_MMC_DAT_3, + /* USB */ + GPIO88_USBH1_PWR, + GPIO89_USBH1_PEN, + /* PWM0 */ + GPIO16_PWM0_OUT, +}; + +/* + * pcm990_lcd_power - control power supply to the LCD + * @on: 0 = switch off, 1 = switch on + * + * Called by the pxafb driver + */ +#ifndef CONFIG_PCM990_DISPLAY_NONE +static void pcm990_lcd_power(int on, struct fb_var_screeninfo *var) +{ + if (on) { + /* enable LCD-Latches + * power on LCD + */ + __PCM990_CTRL_REG(PCM990_CTRL_PHYS + PCM990_CTRL_REG3) = + PCM990_CTRL_LCDPWR + PCM990_CTRL_LCDON; + } else { + /* disable LCD-Latches + * power off LCD + */ + __PCM990_CTRL_REG(PCM990_CTRL_PHYS + PCM990_CTRL_REG3) = 0x00; + } +} +#endif + +#if defined(CONFIG_PCM990_DISPLAY_SHARP) +static struct pxafb_mode_info fb_info_sharp_lq084v1dg21 = { + .pixclock = 28000, + .xres = 640, + .yres = 480, + .bpp = 16, + .hsync_len = 20, + .left_margin = 103, + .right_margin = 47, + .vsync_len = 6, + .upper_margin = 28, + .lower_margin = 5, + .sync = 0, + .cmap_greyscale = 0, +}; + +static struct pxafb_mach_info pcm990_fbinfo __initdata = { + .modes = &fb_info_sharp_lq084v1dg21, + .num_modes = 1, + .lccr0 = LCCR0_PAS, + .lccr3 = LCCR3_PCP, + .pxafb_lcd_power = pcm990_lcd_power, +}; +#elif defined(CONFIG_PCM990_DISPLAY_NEC) +struct pxafb_mode_info fb_info_nec_nl6448bc20_18d = { + .pixclock = 39720, + .xres = 640, + .yres = 480, + .bpp = 16, + .hsync_len = 32, + .left_margin = 16, + .right_margin = 48, + .vsync_len = 2, + .upper_margin = 12, + .lower_margin = 17, + .sync = 0, + .cmap_greyscale = 0, +}; + +static struct pxafb_mach_info pcm990_fbinfo __initdata = { + .modes = &fb_info_nec_nl6448bc20_18d, + .num_modes = 1, + .lccr0 = LCCR0_Act, + .lccr3 = LCCR3_PixFlEdg, + .pxafb_lcd_power = pcm990_lcd_power, +}; +#endif + +static struct platform_pwm_backlight_data pcm990_backlight_data = { + .pwm_id = 0, + .max_brightness = 1023, + .dft_brightness = 1023, + .pwm_period_ns = 78770, +}; + +static struct platform_device pcm990_backlight_device = { + .name = "pwm-backlight", + .dev = { + .parent = &pxa27x_device_pwm0.dev, + .platform_data = &pcm990_backlight_data, + }, +}; /* - * The PCM-990 development baseboard uses PCM-027's hardeware in the + * The PCM-990 development baseboard uses PCM-027's hardware in the * following way: * * - LCD support is in use @@ -155,8 +262,7 @@ static void pcm990_irq_handler(unsigned int irq, struct irq_desc *desc) GPIO_bit(PCM990_CTRL_INT_IRQ_GPIO); if (likely(pending)) { irq = PCM027_IRQ(0) + __ffs(pending); - desc = irq_desc + irq; - desc_handle_irq(irq, desc); + generic_handle_irq(irq); } pending = (~PCM990_INTSETCLR) & pcm990_irq_enabled; } while (pending); @@ -185,16 +291,6 @@ static int pcm990_mci_init(struct device *dev, irq_handler_t mci_detect_int, { int err; - /* - * enable GPIO for PXA27x MMC controller - */ - pxa_gpio_mode(GPIO32_MMCCLK_MD); - pxa_gpio_mode(GPIO112_MMCCMD_MD); - pxa_gpio_mode(GPIO92_MMCDAT0_MD); - pxa_gpio_mode(GPIO109_MMCDAT1_MD); - pxa_gpio_mode(GPIO110_MMCDAT2_MD); - pxa_gpio_mode(GPIO111_MMCDAT3_MD); - err = request_irq(PCM027_MMCDET_IRQ, mci_detect_int, IRQF_DISABLED, "MMC card detect", data); if (err) @@ -231,61 +327,37 @@ static struct pxamci_platform_data pcm990_mci_platform_data = { .exit = pcm990_mci_exit, }; -/* - * init OHCI hardware to work with - * - * Note: Only USB port 1 (host only) is connected - * - * GPIO88 (USBHPWR#1): overcurrent in, overcurrent when low - * GPIO89 (USBHPEN#1): power-on out, on when low - */ -static int pcm990_ohci_init(struct device *dev) -{ - pxa_gpio_mode(PCM990_USB_OVERCURRENT); - pxa_gpio_mode(PCM990_USB_PWR_EN); - /* - * disable USB port 2 and 3 - * power sense is active low - */ - UHCHR = ((UHCHR) | UHCHR_PCPL | UHCHR_PSPL | UHCHR_SSEP2 | - UHCHR_SSEP3) & ~(UHCHR_SSEP1 | UHCHR_SSE); - /* - * wait 10ms after Power on - * overcurrent per port - * power switch per port - */ - UHCRHDA = (5<<24) | (1<<11) | (1<<8); /* FIXME: Required? */ - - return 0; -} - static struct pxaohci_platform_data pcm990_ohci_platform_data = { .port_mode = PMM_PERPORT_MODE, - .init = pcm990_ohci_init, - .exit = NULL, + .flags = ENABLE_PORT1 | POWER_CONTROL_LOW | POWER_SENSE_LOW, + .power_on_delay = 10, }; /* * PXA27x Camera specific stuff */ #if defined(CONFIG_VIDEO_PXA27x) || defined(CONFIG_VIDEO_PXA27x_MODULE) +static unsigned long pcm990_camera_pin_config[] = { + /* CIF */ + GPIO98_CIF_DD_0, + GPIO105_CIF_DD_1, + GPIO104_CIF_DD_2, + GPIO103_CIF_DD_3, + GPIO95_CIF_DD_4, + GPIO94_CIF_DD_5, + GPIO93_CIF_DD_6, + GPIO108_CIF_DD_7, + GPIO107_CIF_DD_8, + GPIO106_CIF_DD_9, + GPIO42_CIF_MCLK, + GPIO45_CIF_PCLK, + GPIO43_CIF_FV, + GPIO44_CIF_LV, +}; + static int pcm990_pxacamera_init(struct device *dev) { - pxa_gpio_mode(GPIO98_CIF_DD_0_MD); - pxa_gpio_mode(GPIO105_CIF_DD_1_MD); - pxa_gpio_mode(GPIO104_CIF_DD_2_MD); - pxa_gpio_mode(GPIO103_CIF_DD_3_MD); - pxa_gpio_mode(GPIO95_CIF_DD_4_MD); - pxa_gpio_mode(GPIO94_CIF_DD_5_MD); - pxa_gpio_mode(GPIO93_CIF_DD_6_MD); - pxa_gpio_mode(GPIO108_CIF_DD_7_MD); - pxa_gpio_mode(GPIO107_CIF_DD_8_MD); - pxa_gpio_mode(GPIO106_CIF_DD_9_MD); - pxa_gpio_mode(GPIO42_CIF_MCLK_MD); - pxa_gpio_mode(GPIO45_CIF_PCLK_MD); - pxa_gpio_mode(GPIO43_CIF_FV_MD); - pxa_gpio_mode(GPIO44_CIF_LV_MD); - + pxa2xx_mfp_config(ARRAY_AND_SIZE(pcm990_camera_pin_config)); return 0; } @@ -333,36 +405,6 @@ static struct i2c_board_info __initdata pcm990_i2c_devices[] = { #endif /* CONFIG_VIDEO_PXA27x ||CONFIG_VIDEO_PXA27x_MODULE */ /* - * AC97 support - * Note: The connected AC97 mixer also reports interrupts at PCM990_AC97_IRQ - */ -static struct resource pxa27x_ac97_resources[] = { - [0] = { - .start = 0x40500000, - .end = 0x40500000 + 0xfff, - .flags = IORESOURCE_MEM, - }, - [1] = { - .start = IRQ_AC97, - .end = IRQ_AC97, - .flags = IORESOURCE_IRQ, - }, -}; - -static u64 pxa_ac97_dmamask = 0xffffffffUL; - -static struct platform_device pxa27x_device_ac97 = { - .name = "pxa2xx-ac97", - .id = -1, - .dev = { - .dma_mask = &pxa_ac97_dmamask, - .coherent_dma_mask = 0xffffffff, - }, - .num_resources = ARRAY_SIZE(pxa27x_ac97_resources), - .resource = pxa27x_ac97_resources, -}; - -/* * enable generic access to the base board control CPLDs U6 and U7 */ static struct map_desc pcm990_io_desc[] __initdata = { @@ -387,13 +429,18 @@ static struct map_desc pcm990_io_desc[] __initdata = { */ void __init pcm990_baseboard_init(void) { + pxa2xx_mfp_config(ARRAY_AND_SIZE(pcm990_pin_config)); + /* register CPLD access */ - iotable_init(pcm990_io_desc, ARRAY_SIZE(pcm990_io_desc)); + iotable_init(ARRAY_AND_SIZE(pcm990_io_desc)); /* register CPLD's IRQ controller */ pcm990_init_irq(); - platform_device_register(&pxa27x_device_ac97); +#ifndef CONFIG_PCM990_DISPLAY_NONE + set_pxa_fb_info(&pcm990_fbinfo); +#endif + platform_device_register(&pcm990_backlight_device); /* MMC */ pxa_set_mci_info(&pcm990_mci_platform_data); @@ -402,13 +449,13 @@ void __init pcm990_baseboard_init(void) pxa_set_ohci_info(&pcm990_ohci_platform_data); pxa_set_i2c_info(NULL); + pxa_set_ac97_info(NULL); #if defined(CONFIG_VIDEO_PXA27x) || defined(CONFIG_VIDEO_PXA27x_MODULE) pxa_set_camera_info(&pcm990_pxacamera_platform_data); - i2c_register_board_info(0, pcm990_i2c_devices, - ARRAY_SIZE(pcm990_i2c_devices)); + i2c_register_board_info(0, ARRAY_AND_SIZE(pcm990_i2c_devices)); #endif - printk(KERN_INFO"PCM-990 Evaluation baseboard initialized\n"); + printk(KERN_INFO "PCM-990 Evaluation baseboard initialized\n"); } diff --git a/arch/arm/mach-pxa/pm.c b/arch/arm/mach-pxa/pm.c index 7d4debbdcca..164eb0bb632 100644 --- a/arch/arm/mach-pxa/pm.c +++ b/arch/arm/mach-pxa/pm.c @@ -16,12 +16,12 @@ #include <linux/errno.h> #include <linux/time.h> -#include <asm/hardware.h> +#include <mach/hardware.h> #include <asm/memory.h> #include <asm/system.h> -#include <asm/arch/pm.h> -#include <asm/arch/pxa-regs.h> -#include <asm/arch/lubbock.h> +#include <mach/pm.h> +#include <mach/pxa-regs.h> +#include <mach/lubbock.h> #include <asm/mach/time.h> struct pxa_cpu_pm_fns *pxa_cpu_pm_fns; @@ -86,9 +86,27 @@ static int pxa_pm_valid(suspend_state_t state) return -EINVAL; } +static int pxa_pm_prepare(void) +{ + int ret = 0; + + if (pxa_cpu_pm_fns && pxa_cpu_pm_fns->prepare) + ret = pxa_cpu_pm_fns->prepare(); + + return ret; +} + +static void pxa_pm_finish(void) +{ + if (pxa_cpu_pm_fns && pxa_cpu_pm_fns->finish) + pxa_cpu_pm_fns->finish(); +} + static struct platform_suspend_ops pxa_pm_ops = { .valid = pxa_pm_valid, .enter = pxa_pm_enter, + .prepare = pxa_pm_prepare, + .finish = pxa_pm_finish, }; static int __init pxa_pm_init(void) diff --git a/arch/arm/mach-pxa/poodle.c b/arch/arm/mach-pxa/poodle.c index 0b30f25cff3..2e3bd8b1523 100644 --- a/arch/arm/mach-pxa/poodle.c +++ b/arch/arm/mach-pxa/poodle.c @@ -20,8 +20,11 @@ #include <linux/fb.h> #include <linux/pm.h> #include <linux/delay.h> +#include <linux/gpio.h> +#include <linux/spi/spi.h> +#include <linux/spi/ads7846.h> -#include <asm/hardware.h> +#include <mach/hardware.h> #include <asm/mach-types.h> #include <asm/irq.h> #include <asm/setup.h> @@ -31,15 +34,18 @@ #include <asm/mach/map.h> #include <asm/mach/irq.h> -#include <asm/arch/pxa-regs.h> -#include <asm/arch/pxa2xx-gpio.h> -#include <asm/arch/mmc.h> -#include <asm/arch/udc.h> -#include <asm/arch/irda.h> -#include <asm/arch/poodle.h> -#include <asm/arch/pxafb.h> -#include <asm/arch/sharpsl.h> -#include <asm/arch/ssp.h> +#include <mach/pxa-regs.h> +#include <mach/pxa2xx-regs.h> +#include <mach/mfp-pxa25x.h> +#include <mach/mmc.h> +#include <mach/udc.h> +#include <mach/i2c.h> +#include <mach/irda.h> +#include <mach/poodle.h> +#include <mach/pxafb.h> +#include <mach/sharpsl.h> +#include <mach/ssp.h> +#include <mach/pxa2xx_spi.h> #include <asm/hardware/scoop.h> #include <asm/hardware/locomo.h> @@ -49,6 +55,88 @@ #include "devices.h" #include "sharpsl.h" +static unsigned long poodle_pin_config[] __initdata = { + /* I/O */ + GPIO79_nCS_3, + GPIO80_nCS_4, + GPIO18_RDY, + + /* Clock */ + GPIO12_32KHz, + + /* SSP1 */ + GPIO23_SSP1_SCLK, + GPIO25_SSP1_TXD, + GPIO26_SSP1_RXD, + GPIO24_GPIO, /* POODLE_GPIO_TP_CS - SFRM as chip select */ + + /* I2S */ + GPIO28_I2S_BITCLK_OUT, + GPIO29_I2S_SDATA_IN, + GPIO30_I2S_SDATA_OUT, + GPIO31_I2S_SYNC, + GPIO32_I2S_SYSCLK, + + /* Infra-Red */ + GPIO47_FICP_TXD, + GPIO46_FICP_RXD, + + /* FFUART */ + GPIO40_FFUART_DTR, + GPIO41_FFUART_RTS, + GPIO39_FFUART_TXD, + GPIO37_FFUART_DSR, + GPIO34_FFUART_RXD, + GPIO35_FFUART_CTS, + + /* LCD */ + GPIO58_LCD_LDD_0, + GPIO59_LCD_LDD_1, + GPIO60_LCD_LDD_2, + GPIO61_LCD_LDD_3, + GPIO62_LCD_LDD_4, + GPIO63_LCD_LDD_5, + GPIO64_LCD_LDD_6, + GPIO65_LCD_LDD_7, + GPIO66_LCD_LDD_8, + GPIO67_LCD_LDD_9, + GPIO68_LCD_LDD_10, + GPIO69_LCD_LDD_11, + GPIO70_LCD_LDD_12, + GPIO71_LCD_LDD_13, + GPIO72_LCD_LDD_14, + GPIO73_LCD_LDD_15, + GPIO74_LCD_FCLK, + GPIO75_LCD_LCLK, + GPIO76_LCD_PCLK, + GPIO77_LCD_BIAS, + + /* PC Card */ + GPIO48_nPOE, + GPIO49_nPWE, + GPIO50_nPIOR, + GPIO51_nPIOW, + GPIO52_nPCE_1, + GPIO53_nPCE_2, + GPIO54_nPSKTSEL, + GPIO55_nPREG, + GPIO56_nPWAIT, + GPIO57_nIOIS16, + + /* MMC */ + GPIO6_MMC_CLK, + GPIO8_MMC_CS0, + + /* GPIO */ + GPIO9_GPIO, /* POODLE_GPIO_nSD_DETECT */ + GPIO7_GPIO, /* POODLE_GPIO_nSD_WP */ + GPIO3_GPIO, /* POODLE_GPIO_SD_PWR */ + GPIO33_GPIO, /* POODLE_GPIO_SD_PWR1 */ + + GPIO20_GPIO, /* POODLE_GPIO_USB_PULLUP */ + GPIO22_GPIO, /* POODLE_GPIO_IR_ON */ +}; + static struct resource poodle_scoop_resources[] = { [0] = { .start = 0x10800000, @@ -60,6 +148,7 @@ static struct resource poodle_scoop_resources[] = { static struct scoop_config poodle_scoop_setup = { .io_dir = POODLE_SCOOP_IO_DIR, .io_out = POODLE_SCOOP_IO_OUT, + .gpio_base = POODLE_SCOOP_GPIO_BASE, }; struct platform_device poodle_scoop_device = { @@ -72,27 +161,6 @@ struct platform_device poodle_scoop_device = { .resource = poodle_scoop_resources, }; -static void poodle_pcmcia_init(void) -{ - /* Setup default state of GPIO outputs - before we enable them as outputs. */ - GPSR(GPIO48_nPOE) = GPIO_bit(GPIO48_nPOE) | - GPIO_bit(GPIO49_nPWE) | GPIO_bit(GPIO50_nPIOR) | - GPIO_bit(GPIO51_nPIOW) | GPIO_bit(GPIO52_nPCE_1) | - GPIO_bit(GPIO53_nPCE_2); - - pxa_gpio_mode(GPIO48_nPOE_MD); - pxa_gpio_mode(GPIO49_nPWE_MD); - pxa_gpio_mode(GPIO50_nPIOR_MD); - pxa_gpio_mode(GPIO51_nPIOW_MD); - pxa_gpio_mode(GPIO55_nPREG_MD); - pxa_gpio_mode(GPIO56_nPWAIT_MD); - pxa_gpio_mode(GPIO57_nIOIS16_MD); - pxa_gpio_mode(GPIO52_nPCE_1_MD); - pxa_gpio_mode(GPIO53_nPCE_2_MD); - pxa_gpio_mode(GPIO54_pSKTSEL_MD); -} - static struct scoop_pcmcia_dev poodle_pcmcia_scoop[] = { { .dev = &poodle_scoop_device.dev, @@ -105,7 +173,6 @@ static struct scoop_pcmcia_dev poodle_pcmcia_scoop[] = { static struct scoop_pcmcia_config poodle_pcmcia_config = { .devs = &poodle_pcmcia_scoop[0], .num_devs = 1, - .pcmcia_init = poodle_pcmcia_init, }; EXPORT_SYMBOL(poodle_scoop_device); @@ -134,62 +201,55 @@ struct platform_device poodle_locomo_device = { EXPORT_SYMBOL(poodle_locomo_device); -/* - * Poodle SSP Device - */ - -struct platform_device poodle_ssp_device = { - .name = "corgi-ssp", - .id = -1, -}; - -struct corgissp_machinfo poodle_ssp_machinfo = { - .port = 1, - .cs_lcdcon = -1, - .cs_ads7846 = -1, - .cs_max1111 = -1, - .clk_lcdcon = 2, - .clk_ads7846 = 36, - .clk_max1111 = 2, +#if defined(CONFIG_SPI_PXA2XX) || defined(CONFIG_SPI_PXA2XX_MODULE) +static struct pxa2xx_spi_master poodle_spi_info = { + .num_chipselect = 1, }; - -/* - * Poodle Touch Screen Device - */ -static struct resource poodlets_resources[] = { - [0] = { - .start = POODLE_IRQ_GPIO_TP_INT, - .end = POODLE_IRQ_GPIO_TP_INT, - .flags = IORESOURCE_IRQ, - }, +static struct ads7846_platform_data poodle_ads7846_info = { + .model = 7846, + .vref_delay_usecs = 100, + .x_plate_ohms = 419, + .y_plate_ohms = 486, + .gpio_pendown = POODLE_GPIO_TP_INT, }; -static unsigned long poodle_get_hsync_invperiod(void) +static void ads7846_cs(u32 command) { - return 0; + gpio_set_value(POODLE_GPIO_TP_CS, !(command == PXA2XX_CS_ASSERT)); } -static void poodle_null_hsync(void) -{ -} - -static struct corgits_machinfo poodle_ts_machinfo = { - .get_hsync_invperiod = poodle_get_hsync_invperiod, - .put_hsync = poodle_null_hsync, - .wait_hsync = poodle_null_hsync, +static struct pxa2xx_spi_chip poodle_ads7846_chip = { + .cs_control = ads7846_cs, }; -static struct platform_device poodle_ts_device = { - .name = "corgi-ts", - .dev = { - .platform_data = &poodle_ts_machinfo, +static struct spi_board_info poodle_spi_devices[] = { + { + .modalias = "ads7846", + .max_speed_hz = 10000, + .bus_num = 1, + .platform_data = &poodle_ads7846_info, + .controller_data= &poodle_ads7846_chip, + .irq = gpio_to_irq(POODLE_GPIO_TP_INT), }, - .id = -1, - .num_resources = ARRAY_SIZE(poodlets_resources), - .resource = poodlets_resources, }; +static void __init poodle_init_spi(void) +{ + int err; + + err = gpio_request(POODLE_GPIO_TP_CS, "ADS7846_CS"); + if (err) + return; + + gpio_direction_output(POODLE_GPIO_TP_CS, 1); + + pxa2xx_set_spi_info(1, &poodle_spi_info); + spi_register_board_info(ARRAY_AND_SIZE(poodle_spi_devices)); +} +#else +static inline void poodle_init_spi(void) {} +#endif /* * MMC/SD Device @@ -203,22 +263,50 @@ static int poodle_mci_init(struct device *dev, irq_handler_t poodle_detect_int, { int err; - /* setup GPIO for PXA25x MMC controller */ - pxa_gpio_mode(GPIO6_MMCCLK_MD); - pxa_gpio_mode(GPIO8_MMCCS0_MD); - pxa_gpio_mode(POODLE_GPIO_nSD_DETECT | GPIO_IN); - pxa_gpio_mode(POODLE_GPIO_nSD_WP | GPIO_IN); - pxa_gpio_mode(POODLE_GPIO_SD_PWR | GPIO_OUT); - pxa_gpio_mode(POODLE_GPIO_SD_PWR1 | GPIO_OUT); + err = gpio_request(POODLE_GPIO_nSD_DETECT, "nSD_DETECT"); + if (err) + goto err_out; + + err = gpio_request(POODLE_GPIO_nSD_WP, "nSD_WP"); + if (err) + goto err_free_1; + + err = gpio_request(POODLE_GPIO_SD_PWR, "SD_PWR"); + if (err) + goto err_free_2; + + err = gpio_request(POODLE_GPIO_SD_PWR1, "SD_PWR1"); + if (err) + goto err_free_3; + + gpio_direction_input(POODLE_GPIO_nSD_DETECT); + gpio_direction_input(POODLE_GPIO_nSD_WP); + + gpio_direction_output(POODLE_GPIO_SD_PWR, 0); + gpio_direction_output(POODLE_GPIO_SD_PWR1, 0); poodle_mci_platform_data.detect_delay = msecs_to_jiffies(250); err = request_irq(POODLE_IRQ_GPIO_nSD_DETECT, poodle_detect_int, IRQF_DISABLED | IRQF_TRIGGER_RISING | IRQF_TRIGGER_FALLING, "MMC card detect", data); - if (err) - printk(KERN_ERR "poodle_mci_init: MMC/SD: can't request MMC card detect IRQ\n"); + if (err) { + pr_err("%s: MMC/SD: can't request MMC card detect IRQ\n", + __func__); + goto err_free_4; + } + + return 0; +err_free_4: + gpio_free(POODLE_GPIO_SD_PWR1); +err_free_3: + gpio_free(POODLE_GPIO_SD_PWR); +err_free_2: + gpio_free(POODLE_GPIO_nSD_WP); +err_free_1: + gpio_free(POODLE_GPIO_nSD_DETECT); +err_out: return err; } @@ -226,18 +314,19 @@ static void poodle_mci_setpower(struct device *dev, unsigned int vdd) { struct pxamci_platform_data* p_d = dev->platform_data; - if (( 1 << vdd) & p_d->ocr_mask) { - GPSR(POODLE_GPIO_SD_PWR) = GPIO_bit(POODLE_GPIO_SD_PWR); + if ((1 << vdd) & p_d->ocr_mask) { + gpio_set_value(POODLE_GPIO_SD_PWR, 1); mdelay(2); - GPSR(POODLE_GPIO_SD_PWR1) = GPIO_bit(POODLE_GPIO_SD_PWR1); + gpio_set_value(POODLE_GPIO_SD_PWR1, 1); } else { - GPCR(POODLE_GPIO_SD_PWR1) = GPIO_bit(POODLE_GPIO_SD_PWR1); - GPCR(POODLE_GPIO_SD_PWR) = GPIO_bit(POODLE_GPIO_SD_PWR); + gpio_set_value(POODLE_GPIO_SD_PWR1, 0); + gpio_set_value(POODLE_GPIO_SD_PWR, 0); } } static int poodle_mci_get_ro(struct device *dev) { + return !!gpio_get_value(POODLE_GPIO_nSD_WP); return GPLR(POODLE_GPIO_nSD_WP) & GPIO_bit(POODLE_GPIO_nSD_WP); } @@ -245,6 +334,10 @@ static int poodle_mci_get_ro(struct device *dev) static void poodle_mci_exit(struct device *dev, void *data) { free_irq(POODLE_IRQ_GPIO_nSD_DETECT, data); + gpio_free(POODLE_GPIO_SD_PWR1); + gpio_free(POODLE_GPIO_SD_PWR); + gpio_free(POODLE_GPIO_nSD_WP); + gpio_free(POODLE_GPIO_nSD_DETECT); } static struct pxamci_platform_data poodle_mci_platform_data = { @@ -261,37 +354,41 @@ static struct pxamci_platform_data poodle_mci_platform_data = { */ static void poodle_irda_transceiver_mode(struct device *dev, int mode) { - if (mode & IR_OFF) { - GPSR(POODLE_GPIO_IR_ON) = GPIO_bit(POODLE_GPIO_IR_ON); - } else { - GPCR(POODLE_GPIO_IR_ON) = GPIO_bit(POODLE_GPIO_IR_ON); - } + gpio_set_value(POODLE_GPIO_IR_ON, mode & IR_OFF); + pxa2xx_transceiver_mode(dev, mode); +} + +static int poodle_irda_startup(struct device *dev) +{ + int err; + + err = gpio_request(POODLE_GPIO_IR_ON, "IR_ON"); + if (err) + return err; + + gpio_direction_output(POODLE_GPIO_IR_ON, 1); + return 0; +} + +static void poodle_irda_shutdown(struct device *dev) +{ + gpio_free(POODLE_GPIO_IR_ON); } static struct pxaficp_platform_data poodle_ficp_platform_data = { - .transceiver_cap = IR_SIRMODE | IR_OFF, - .transceiver_mode = poodle_irda_transceiver_mode, + .transceiver_cap = IR_SIRMODE | IR_OFF, + .transceiver_mode = poodle_irda_transceiver_mode, + .startup = poodle_irda_startup, + .shutdown = poodle_irda_shutdown, }; /* * USB Device Controller */ -static void poodle_udc_command(int cmd) -{ - switch(cmd) { - case PXA2XX_UDC_CMD_CONNECT: - GPSR(POODLE_GPIO_USB_PULLUP) = GPIO_bit(POODLE_GPIO_USB_PULLUP); - break; - case PXA2XX_UDC_CMD_DISCONNECT: - GPCR(POODLE_GPIO_USB_PULLUP) = GPIO_bit(POODLE_GPIO_USB_PULLUP); - break; - } -} - static struct pxa2xx_udc_mach_info udc_info __initdata = { /* no connect GPIO; poodle can't tell connection status */ - .udc_command = poodle_udc_command, + .gpio_pullup = POODLE_GPIO_USB_PULLUP, }; @@ -313,15 +410,12 @@ static struct pxafb_mode_info poodle_fb_mode = { static struct pxafb_mach_info poodle_fb_info = { .modes = &poodle_fb_mode, .num_modes = 1, - .lccr0 = LCCR0_Act | LCCR0_Sngl | LCCR0_Color, - .lccr3 = 0, + .lcd_conn = LCD_COLOR_TFT_16BPP, }; static struct platform_device *devices[] __initdata = { &poodle_locomo_device, &poodle_scoop_device, - &poodle_ssp_device, - &poodle_ts_device, }; static void poodle_poweroff(void) @@ -341,58 +435,23 @@ static void __init poodle_init(void) pm_power_off = poodle_poweroff; arm_pm_restart = poodle_restart; - /* setup sleep mode values */ - PWER = 0x00000002; - PFER = 0x00000000; - PRER = 0x00000002; - PGSR0 = 0x00008000; - PGSR1 = 0x003F0202; - PGSR2 = 0x0001C000; PCFR |= PCFR_OPDE; - /* cpu initialize */ - /* Pgsr Register */ - PGSR0 = 0x0146dd80; - PGSR1 = 0x03bf0890; - PGSR2 = 0x0001c000; - - /* Alternate Register */ - GAFR0_L = 0x01001000; - GAFR0_U = 0x591a8010; - GAFR1_L = 0x900a8451; - GAFR1_U = 0xaaa5aaaa; - GAFR2_L = 0x8aaaaaaa; - GAFR2_U = 0x00000002; - - /* Direction Register */ - GPDR0 = 0xd3f0904c; - GPDR1 = 0xfcffb7d3; - GPDR2 = 0x0001ffff; - - /* Output Register */ - GPCR0 = 0x00000000; - GPCR1 = 0x00000000; - GPCR2 = 0x00000000; - - GPSR0 = 0x00400000; - GPSR1 = 0x00000000; - GPSR2 = 0x00000000; + pxa2xx_mfp_config(ARRAY_AND_SIZE(poodle_pin_config)); + + platform_scoop_config = &poodle_pcmcia_config; + + ret = platform_add_devices(devices, ARRAY_SIZE(devices)); + if (ret) + pr_warning("poodle: Unable to register LoCoMo device\n"); set_pxa_fb_parent(&poodle_locomo_device.dev); set_pxa_fb_info(&poodle_fb_info); - pxa_gpio_mode(POODLE_GPIO_USB_PULLUP | GPIO_OUT); - pxa_gpio_mode(POODLE_GPIO_IR_ON | GPIO_OUT); pxa_set_udc_info(&udc_info); pxa_set_mci_info(&poodle_mci_platform_data); pxa_set_ficp_info(&poodle_ficp_platform_data); - - platform_scoop_config = &poodle_pcmcia_config; - - ret = platform_add_devices(devices, ARRAY_SIZE(devices)); - if (ret) { - printk(KERN_WARNING "poodle: Unable to register LoCoMo device\n"); - } - corgi_ssp_set_machinfo(&poodle_ssp_machinfo); + pxa_set_i2c_info(NULL); + poodle_init_spi(); } static void __init fixup_poodle(struct machine_desc *desc, diff --git a/arch/arm/mach-pxa/pwm.c b/arch/arm/mach-pxa/pwm.c new file mode 100644 index 00000000000..316cd986da5 --- /dev/null +++ b/arch/arm/mach-pxa/pwm.c @@ -0,0 +1,319 @@ +/* + * linux/arch/arm/mach-pxa/pwm.c + * + * simple driver for PWM (Pulse Width Modulator) controller + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + * + * 2008-02-13 initial version + * eric miao <eric.miao@marvell.com> + */ + +#include <linux/module.h> +#include <linux/kernel.h> +#include <linux/platform_device.h> +#include <linux/err.h> +#include <linux/clk.h> +#include <linux/io.h> +#include <linux/pwm.h> + +#include <asm/div64.h> +#include <mach/pxa-regs.h> + +/* PWM registers and bits definitions */ +#define PWMCR (0x00) +#define PWMDCR (0x04) +#define PWMPCR (0x08) + +#define PWMCR_SD (1 << 6) +#define PWMDCR_FD (1 << 10) + +struct pwm_device { + struct list_head node; + struct platform_device *pdev; + + const char *label; + struct clk *clk; + int clk_enabled; + void __iomem *mmio_base; + + unsigned int use_count; + unsigned int pwm_id; +}; + +/* + * period_ns = 10^9 * (PRESCALE + 1) * (PV + 1) / PWM_CLK_RATE + * duty_ns = 10^9 * (PRESCALE + 1) * DC / PWM_CLK_RATE + */ +int pwm_config(struct pwm_device *pwm, int duty_ns, int period_ns) +{ + unsigned long long c; + unsigned long period_cycles, prescale, pv, dc; + + if (pwm == NULL || period_ns == 0 || duty_ns > period_ns) + return -EINVAL; + + c = clk_get_rate(pwm->clk); + c = c * period_ns; + do_div(c, 1000000000); + period_cycles = c; + + if (period_cycles < 0) + period_cycles = 1; + prescale = (period_cycles - 1) / 1024; + pv = period_cycles / (prescale + 1) - 1; + + if (prescale > 63) + return -EINVAL; + + if (duty_ns == period_ns) + dc = PWMDCR_FD; + else + dc = (pv + 1) * duty_ns / period_ns; + + /* NOTE: the clock to PWM has to be enabled first + * before writing to the registers + */ + clk_enable(pwm->clk); + __raw_writel(prescale, pwm->mmio_base + PWMCR); + __raw_writel(dc, pwm->mmio_base + PWMDCR); + __raw_writel(pv, pwm->mmio_base + PWMPCR); + clk_disable(pwm->clk); + + return 0; +} +EXPORT_SYMBOL(pwm_config); + +int pwm_enable(struct pwm_device *pwm) +{ + int rc = 0; + + if (!pwm->clk_enabled) { + rc = clk_enable(pwm->clk); + if (!rc) + pwm->clk_enabled = 1; + } + return rc; +} +EXPORT_SYMBOL(pwm_enable); + +void pwm_disable(struct pwm_device *pwm) +{ + if (pwm->clk_enabled) { + clk_disable(pwm->clk); + pwm->clk_enabled = 0; + } +} +EXPORT_SYMBOL(pwm_disable); + +static DEFINE_MUTEX(pwm_lock); +static LIST_HEAD(pwm_list); + +struct pwm_device *pwm_request(int pwm_id, const char *label) +{ + struct pwm_device *pwm; + int found = 0; + + mutex_lock(&pwm_lock); + + list_for_each_entry(pwm, &pwm_list, node) { + if (pwm->pwm_id == pwm_id) { + found = 1; + break; + } + } + + if (found) { + if (pwm->use_count == 0) { + pwm->use_count++; + pwm->label = label; + } else + pwm = ERR_PTR(-EBUSY); + } else + pwm = ERR_PTR(-ENOENT); + + mutex_unlock(&pwm_lock); + return pwm; +} +EXPORT_SYMBOL(pwm_request); + +void pwm_free(struct pwm_device *pwm) +{ + mutex_lock(&pwm_lock); + + if (pwm->use_count) { + pwm->use_count--; + pwm->label = NULL; + } else + pr_warning("PWM device already freed\n"); + + mutex_unlock(&pwm_lock); +} +EXPORT_SYMBOL(pwm_free); + +static inline void __add_pwm(struct pwm_device *pwm) +{ + mutex_lock(&pwm_lock); + list_add_tail(&pwm->node, &pwm_list); + mutex_unlock(&pwm_lock); +} + +static struct pwm_device *pwm_probe(struct platform_device *pdev, + unsigned int pwm_id, struct pwm_device *parent_pwm) +{ + struct pwm_device *pwm; + struct resource *r; + int ret = 0; + + pwm = kzalloc(sizeof(struct pwm_device), GFP_KERNEL); + if (pwm == NULL) { + dev_err(&pdev->dev, "failed to allocate memory\n"); + return ERR_PTR(-ENOMEM); + } + + pwm->clk = clk_get(&pdev->dev, "PWMCLK"); + if (IS_ERR(pwm->clk)) { + ret = PTR_ERR(pwm->clk); + goto err_free; + } + pwm->clk_enabled = 0; + + pwm->use_count = 0; + pwm->pwm_id = pwm_id; + pwm->pdev = pdev; + + if (parent_pwm != NULL) { + /* registers for the second PWM has offset of 0x10 */ + pwm->mmio_base = parent_pwm->mmio_base + 0x10; + __add_pwm(pwm); + return pwm; + } + + r = platform_get_resource(pdev, IORESOURCE_MEM, 0); + if (r == NULL) { + dev_err(&pdev->dev, "no memory resource defined\n"); + ret = -ENODEV; + goto err_free_clk; + } + + r = request_mem_region(r->start, r->end - r->start + 1, pdev->name); + if (r == NULL) { + dev_err(&pdev->dev, "failed to request memory resource\n"); + ret = -EBUSY; + goto err_free_clk; + } + + pwm->mmio_base = ioremap(r->start, r->end - r->start + 1); + if (pwm->mmio_base == NULL) { + dev_err(&pdev->dev, "failed to ioremap() registers\n"); + ret = -ENODEV; + goto err_free_mem; + } + + __add_pwm(pwm); + platform_set_drvdata(pdev, pwm); + return pwm; + +err_free_mem: + release_mem_region(r->start, r->end - r->start + 1); +err_free_clk: + clk_put(pwm->clk); +err_free: + kfree(pwm); + return ERR_PTR(ret); +} + +static int __devinit pxa25x_pwm_probe(struct platform_device *pdev) +{ + struct pwm_device *pwm = pwm_probe(pdev, pdev->id, NULL); + + if (IS_ERR(pwm)) + return PTR_ERR(pwm); + + return 0; +} + +static int __devinit pxa27x_pwm_probe(struct platform_device *pdev) +{ + struct pwm_device *pwm; + + pwm = pwm_probe(pdev, pdev->id, NULL); + if (IS_ERR(pwm)) + return PTR_ERR(pwm); + + pwm = pwm_probe(pdev, pdev->id + 2, pwm); + if (IS_ERR(pwm)) + return PTR_ERR(pwm); + + return 0; +} + +static int __devexit pwm_remove(struct platform_device *pdev) +{ + struct pwm_device *pwm; + struct resource *r; + + pwm = platform_get_drvdata(pdev); + if (pwm == NULL) + return -ENODEV; + + mutex_lock(&pwm_lock); + list_del(&pwm->node); + mutex_unlock(&pwm_lock); + + iounmap(pwm->mmio_base); + + r = platform_get_resource(pdev, IORESOURCE_MEM, 0); + release_mem_region(r->start, r->end - r->start + 1); + + clk_put(pwm->clk); + kfree(pwm); + return 0; +} + +static struct platform_driver pxa25x_pwm_driver = { + .driver = { + .name = "pxa25x-pwm", + }, + .probe = pxa25x_pwm_probe, + .remove = __devexit_p(pwm_remove), +}; + +static struct platform_driver pxa27x_pwm_driver = { + .driver = { + .name = "pxa27x-pwm", + }, + .probe = pxa27x_pwm_probe, + .remove = __devexit_p(pwm_remove), +}; + +static int __init pwm_init(void) +{ + int ret = 0; + + ret = platform_driver_register(&pxa25x_pwm_driver); + if (ret) { + printk(KERN_ERR "failed to register pxa25x_pwm_driver\n"); + return ret; + } + + ret = platform_driver_register(&pxa27x_pwm_driver); + if (ret) { + printk(KERN_ERR "failed to register pxa27x_pwm_driver\n"); + return ret; + } + + return ret; +} +arch_initcall(pwm_init); + +static void __exit pwm_exit(void) +{ + platform_driver_unregister(&pxa25x_pwm_driver); + platform_driver_unregister(&pxa27x_pwm_driver); +} +module_exit(pwm_exit); + +MODULE_LICENSE("GPL v2"); diff --git a/arch/arm/mach-pxa/pxa25x.c b/arch/arm/mach-pxa/pxa25x.c index e5b417d14bb..25d17a1dab7 100644 --- a/arch/arm/mach-pxa/pxa25x.c +++ b/arch/arm/mach-pxa/pxa25x.c @@ -23,17 +23,25 @@ #include <linux/suspend.h> #include <linux/sysdev.h> -#include <asm/hardware.h> -#include <asm/arch/irqs.h> -#include <asm/arch/pxa-regs.h> -#include <asm/arch/mfp-pxa25x.h> -#include <asm/arch/pm.h> -#include <asm/arch/dma.h> +#include <mach/hardware.h> +#include <mach/irqs.h> +#include <mach/pxa-regs.h> +#include <mach/pxa2xx-regs.h> +#include <mach/mfp-pxa25x.h> +#include <mach/reset.h> +#include <mach/pm.h> +#include <mach/dma.h> #include "generic.h" #include "devices.h" #include "clock.h" +int cpu_is_pxa26x(void) +{ + return cpu_is_pxa250() && ((BOOT_DEF & 0x8) == 0); +} +EXPORT_SYMBOL_GPL(cpu_is_pxa26x); + /* * Various clock factors driven by the CCCR register. */ @@ -108,6 +116,52 @@ static const struct clkops clk_pxa25x_lcd_ops = { .getrate = clk_pxa25x_lcd_getrate, }; +static unsigned long gpio12_config_32k[] = { + GPIO12_32KHz, +}; + +static unsigned long gpio12_config_gpio[] = { + GPIO12_GPIO, +}; + +static void clk_gpio12_enable(struct clk *clk) +{ + pxa2xx_mfp_config(gpio12_config_32k, 1); +} + +static void clk_gpio12_disable(struct clk *clk) +{ + pxa2xx_mfp_config(gpio12_config_gpio, 1); +} + +static const struct clkops clk_pxa25x_gpio12_ops = { + .enable = clk_gpio12_enable, + .disable = clk_gpio12_disable, +}; + +static unsigned long gpio11_config_3m6[] = { + GPIO11_3_6MHz, +}; + +static unsigned long gpio11_config_gpio[] = { + GPIO11_GPIO, +}; + +static void clk_gpio11_enable(struct clk *clk) +{ + pxa2xx_mfp_config(gpio11_config_3m6, 1); +} + +static void clk_gpio11_disable(struct clk *clk) +{ + pxa2xx_mfp_config(gpio11_config_gpio, 1); +} + +static const struct clkops clk_pxa25x_gpio11_ops = { + .enable = clk_gpio11_enable, + .disable = clk_gpio11_disable, +}; + /* * 3.6864MHz -> OST, GPIO, SSP, PWM, PLLs (95.842MHz, 147.456MHz) * 95.842MHz -> MMC 19.169MHz, I2C 31.949MHz, FICP 47.923MHz, USB 47.923MHz @@ -117,24 +171,29 @@ static struct clk pxa25x_hwuart_clk = INIT_CKEN("UARTCLK", HWUART, 14745600, 1, &pxa_device_hwuart.dev) ; +/* + * PXA 2xx clock declarations. + */ static struct clk pxa25x_clks[] = { INIT_CK("LCDCLK", LCD, &clk_pxa25x_lcd_ops, &pxa_device_fb.dev), INIT_CKEN("UARTCLK", FFUART, 14745600, 1, &pxa_device_ffuart.dev), INIT_CKEN("UARTCLK", BTUART, 14745600, 1, &pxa_device_btuart.dev), INIT_CKEN("UARTCLK", STUART, 14745600, 1, NULL), - INIT_CKEN("UDCCLK", USB, 47923000, 5, &pxa_device_udc.dev), + INIT_CKEN("UDCCLK", USB, 47923000, 5, &pxa25x_device_udc.dev), + INIT_CLK("GPIO11_CLK", &clk_pxa25x_gpio11_ops, 3686400, 0, NULL), + INIT_CLK("GPIO12_CLK", &clk_pxa25x_gpio12_ops, 32768, 0, NULL), INIT_CKEN("MMCCLK", MMC, 19169000, 0, &pxa_device_mci.dev), INIT_CKEN("I2CCLK", I2C, 31949000, 0, &pxa_device_i2c.dev), INIT_CKEN("SSPCLK", SSP, 3686400, 0, &pxa25x_device_ssp.dev), INIT_CKEN("SSPCLK", NSSP, 3686400, 0, &pxa25x_device_nssp.dev), INIT_CKEN("SSPCLK", ASSP, 3686400, 0, &pxa25x_device_assp.dev), + INIT_CKEN("PWMCLK", PWM0, 3686400, 0, &pxa25x_device_pwm0.dev), + INIT_CKEN("PWMCLK", PWM1, 3686400, 0, &pxa25x_device_pwm1.dev), INIT_CKEN("AC97CLK", AC97, 24576000, 0, NULL), /* - INIT_CKEN("PWMCLK", PWM0, 3686400, 0, NULL), - INIT_CKEN("PWMCLK", PWM0, 3686400, 0, NULL), INIT_CKEN("I2SCLK", I2S, 14745600, 0, NULL), */ INIT_CKEN("FICPCLK", FICP, 47923000, 0, NULL), @@ -150,48 +209,21 @@ static struct clk pxa25x_clks[] = { * More ones like CP and general purpose register values are preserved * with the stack pointer in sleep.S. */ -enum { SLEEP_SAVE_PGSR0, SLEEP_SAVE_PGSR1, SLEEP_SAVE_PGSR2, - - SLEEP_SAVE_GAFR0_L, SLEEP_SAVE_GAFR0_U, - SLEEP_SAVE_GAFR1_L, SLEEP_SAVE_GAFR1_U, - SLEEP_SAVE_GAFR2_L, SLEEP_SAVE_GAFR2_U, - +enum { SLEEP_SAVE_PSTR, - SLEEP_SAVE_CKEN, - SLEEP_SAVE_COUNT }; static void pxa25x_cpu_pm_save(unsigned long *sleep_save) { - SAVE(PGSR0); SAVE(PGSR1); SAVE(PGSR2); - - SAVE(GAFR0_L); SAVE(GAFR0_U); - SAVE(GAFR1_L); SAVE(GAFR1_U); - SAVE(GAFR2_L); SAVE(GAFR2_U); - SAVE(CKEN); SAVE(PSTR); - - /* Clear GPIO transition detect bits */ - GEDR0 = GEDR0; GEDR1 = GEDR1; GEDR2 = GEDR2; } static void pxa25x_cpu_pm_restore(unsigned long *sleep_save) { - /* ensure not to come back here if it wasn't intended */ - PSPR = 0; - - /* restore registers */ - RESTORE(GAFR0_L); RESTORE(GAFR0_U); - RESTORE(GAFR1_L); RESTORE(GAFR1_U); - RESTORE(GAFR2_L); RESTORE(GAFR2_U); - RESTORE(PGSR0); RESTORE(PGSR1); RESTORE(PGSR2); - - PSSR = PSSR_RDH | PSSR_PH; - RESTORE(CKEN); RESTORE(PSTR); } @@ -203,19 +235,32 @@ static void pxa25x_cpu_pm_enter(suspend_state_t state) switch (state) { case PM_SUSPEND_MEM: - /* set resume return address */ - PSPR = virt_to_phys(pxa_cpu_resume); pxa25x_cpu_suspend(PWRMODE_SLEEP); break; } } +static int pxa25x_cpu_pm_prepare(void) +{ + /* set resume return address */ + PSPR = virt_to_phys(pxa_cpu_resume); + return 0; +} + +static void pxa25x_cpu_pm_finish(void) +{ + /* ensure not to come back here if it wasn't intended */ + PSPR = 0; +} + static struct pxa_cpu_pm_fns pxa25x_cpu_pm_fns = { .save_count = SLEEP_SAVE_COUNT, .valid = suspend_valid_only_mem, .save = pxa25x_cpu_pm_save, .restore = pxa25x_cpu_pm_restore, .enter = pxa25x_cpu_pm_enter, + .prepare = pxa25x_cpu_pm_prepare, + .finish = pxa25x_cpu_pm_finish, }; static void __init pxa25x_init_pm(void) @@ -260,7 +305,7 @@ void __init pxa25x_init_irq(void) } static struct platform_device *pxa25x_devices[] __initdata = { - &pxa_device_udc, + &pxa25x_device_udc, &pxa_device_ffuart, &pxa_device_btuart, &pxa_device_stuart, @@ -269,12 +314,16 @@ static struct platform_device *pxa25x_devices[] __initdata = { &pxa25x_device_ssp, &pxa25x_device_nssp, &pxa25x_device_assp, + &pxa25x_device_pwm0, + &pxa25x_device_pwm1, }; static struct sys_device pxa25x_sysdev[] = { { .cls = &pxa_irq_sysclass, }, { + .cls = &pxa2xx_mfp_sysclass, + }, { .cls = &pxa_gpio_sysclass, }, }; @@ -283,11 +332,10 @@ static int __init pxa25x_init(void) { int i, ret = 0; - /* Only add HWUART for PXA255/26x; PXA210/250/27x do not have it. */ - if (cpu_is_pxa25x()) - clks_register(&pxa25x_hwuart_clk, 1); + if (cpu_is_pxa25x()) { + + reset_status = RCSR; - if (cpu_is_pxa21x() || cpu_is_pxa25x()) { clks_register(pxa25x_clks, ARRAY_SIZE(pxa25x_clks)); if ((ret = pxa_init_dma(16))) @@ -307,9 +355,11 @@ static int __init pxa25x_init(void) return ret; } - /* Only add HWUART for PXA255/26x; PXA210/250/27x do not have it. */ - if (cpu_is_pxa25x()) + /* Only add HWUART for PXA255/26x; PXA210/250 do not have it. */ + if (cpu_is_pxa255() || cpu_is_pxa26x()) { + clks_register(&pxa25x_hwuart_clk, 1); ret = platform_device_register(&pxa_device_hwuart); + } return ret; } diff --git a/arch/arm/mach-pxa/pxa27x.c b/arch/arm/mach-pxa/pxa27x.c index 7e945836e12..3e4ab2279c9 100644 --- a/arch/arm/mach-pxa/pxa27x.c +++ b/arch/arm/mach-pxa/pxa27x.c @@ -18,21 +18,29 @@ #include <linux/platform_device.h> #include <linux/sysdev.h> -#include <asm/hardware.h> +#include <mach/hardware.h> #include <asm/irq.h> -#include <asm/arch/irqs.h> -#include <asm/arch/pxa-regs.h> -#include <asm/arch/pxa2xx-regs.h> -#include <asm/arch/mfp-pxa27x.h> -#include <asm/arch/ohci.h> -#include <asm/arch/pm.h> -#include <asm/arch/dma.h> -#include <asm/arch/i2c.h> +#include <mach/irqs.h> +#include <mach/pxa-regs.h> +#include <mach/pxa2xx-regs.h> +#include <mach/mfp-pxa27x.h> +#include <mach/reset.h> +#include <mach/ohci.h> +#include <mach/pm.h> +#include <mach/dma.h> +#include <mach/i2c.h> #include "generic.h" #include "devices.h" #include "clock.h" +void pxa27x_clear_otgph(void) +{ + if (cpu_is_pxa27x() && (PSSR & PSSR_OTGPH)) + PSSR |= PSSR_OTGPH; +} +EXPORT_SYMBOL(pxa27x_clear_otgph); + /* Crystal clock: 13MHz */ #define BASE_CLK 13000000 @@ -146,7 +154,7 @@ static struct clk pxa27x_clks[] = { INIT_CKEN("I2SCLK", I2S, 14682000, 0, &pxa_device_i2s.dev), INIT_CKEN("I2CCLK", I2C, 32842000, 0, &pxa_device_i2c.dev), - INIT_CKEN("UDCCLK", USB, 48000000, 5, &pxa_device_udc.dev), + INIT_CKEN("UDCCLK", USB, 48000000, 5, &pxa27x_device_udc.dev), INIT_CKEN("MMCCLK", MMC, 19500000, 0, &pxa_device_mci.dev), INIT_CKEN("FICPCLK", FICP, 48000000, 0, &pxa_device_ficp.dev), @@ -157,12 +165,13 @@ static struct clk pxa27x_clks[] = { INIT_CKEN("SSPCLK", SSP1, 13000000, 0, &pxa27x_device_ssp1.dev), INIT_CKEN("SSPCLK", SSP2, 13000000, 0, &pxa27x_device_ssp2.dev), INIT_CKEN("SSPCLK", SSP3, 13000000, 0, &pxa27x_device_ssp3.dev), + INIT_CKEN("PWMCLK", PWM0, 13000000, 0, &pxa27x_device_pwm0.dev), + INIT_CKEN("PWMCLK", PWM1, 13000000, 0, &pxa27x_device_pwm1.dev), INIT_CKEN("AC97CLK", AC97, 24576000, 0, NULL), INIT_CKEN("AC97CONFCLK", AC97CONF, 24576000, 0, NULL), /* - INIT_CKEN("PWMCLK", PWM0, 13000000, 0, NULL), INIT_CKEN("MSLCLK", MSL, 48000000, 0, NULL), INIT_CKEN("USIMCLK", USIM, 48000000, 0, NULL), INIT_CKEN("MSTKCLK", MEMSTK, 19500000, 0, NULL), @@ -181,36 +190,18 @@ static struct clk pxa27x_clks[] = { * More ones like CP and general purpose register values are preserved * with the stack pointer in sleep.S. */ -enum { SLEEP_SAVE_PGSR0, SLEEP_SAVE_PGSR1, SLEEP_SAVE_PGSR2, SLEEP_SAVE_PGSR3, - - SLEEP_SAVE_GAFR0_L, SLEEP_SAVE_GAFR0_U, - SLEEP_SAVE_GAFR1_L, SLEEP_SAVE_GAFR1_U, - SLEEP_SAVE_GAFR2_L, SLEEP_SAVE_GAFR2_U, - SLEEP_SAVE_GAFR3_L, SLEEP_SAVE_GAFR3_U, - +enum { SLEEP_SAVE_PSTR, - SLEEP_SAVE_CKEN, - SLEEP_SAVE_MDREFR, - SLEEP_SAVE_PWER, SLEEP_SAVE_PCFR, SLEEP_SAVE_PRER, - SLEEP_SAVE_PFER, SLEEP_SAVE_PKWR, - + SLEEP_SAVE_PCFR, SLEEP_SAVE_COUNT }; void pxa27x_cpu_pm_save(unsigned long *sleep_save) { - SAVE(PGSR0); SAVE(PGSR1); SAVE(PGSR2); SAVE(PGSR3); - - SAVE(GAFR0_L); SAVE(GAFR0_U); - SAVE(GAFR1_L); SAVE(GAFR1_U); - SAVE(GAFR2_L); SAVE(GAFR2_U); - SAVE(GAFR3_L); SAVE(GAFR3_U); - SAVE(MDREFR); - SAVE(PWER); SAVE(PCFR); SAVE(PRER); - SAVE(PFER); SAVE(PKWR); + SAVE(PCFR); SAVE(CKEN); SAVE(PSTR); @@ -218,24 +209,12 @@ void pxa27x_cpu_pm_save(unsigned long *sleep_save) void pxa27x_cpu_pm_restore(unsigned long *sleep_save) { - /* ensure not to come back here if it wasn't intended */ - PSPR = 0; - - /* restore registers */ - RESTORE(GAFR0_L); RESTORE(GAFR0_U); - RESTORE(GAFR1_L); RESTORE(GAFR1_U); - RESTORE(GAFR2_L); RESTORE(GAFR2_U); - RESTORE(GAFR3_L); RESTORE(GAFR3_U); - RESTORE(PGSR0); RESTORE(PGSR1); RESTORE(PGSR2); RESTORE(PGSR3); - RESTORE(MDREFR); - RESTORE(PWER); RESTORE(PCFR); RESTORE(PRER); - RESTORE(PFER); RESTORE(PKWR); + RESTORE(PCFR); PSSR = PSSR_RDH | PSSR_PH; RESTORE(CKEN); - RESTORE(PSTR); } @@ -257,8 +236,6 @@ void pxa27x_cpu_pm_enter(suspend_state_t state) pxa_cpu_standby(); break; case PM_SUSPEND_MEM: - /* set resume return address */ - PSPR = virt_to_phys(pxa_cpu_resume); pxa27x_cpu_suspend(PWRMODE_SLEEP); break; } @@ -269,12 +246,27 @@ static int pxa27x_cpu_pm_valid(suspend_state_t state) return state == PM_SUSPEND_MEM || state == PM_SUSPEND_STANDBY; } +static int pxa27x_cpu_pm_prepare(void) +{ + /* set resume return address */ + PSPR = virt_to_phys(pxa_cpu_resume); + return 0; +} + +static void pxa27x_cpu_pm_finish(void) +{ + /* ensure not to come back here if it wasn't intended */ + PSPR = 0; +} + static struct pxa_cpu_pm_fns pxa27x_cpu_pm_fns = { .save_count = SLEEP_SAVE_COUNT, .save = pxa27x_cpu_pm_save, .restore = pxa27x_cpu_pm_restore, .valid = pxa27x_cpu_pm_valid, .enter = pxa27x_cpu_pm_enter, + .prepare = pxa27x_cpu_pm_prepare, + .finish = pxa27x_cpu_pm_finish, }; static void __init pxa27x_init_pm(void) @@ -347,13 +339,16 @@ struct platform_device pxa27x_device_i2c_power = { .num_resources = ARRAY_SIZE(i2c_power_resources), }; -void __init pxa_set_i2c_power_info(struct i2c_pxa_platform_data *info) +void __init pxa27x_set_i2c_power_info(struct i2c_pxa_platform_data *info) { + local_irq_disable(); + PCFR |= PCFR_PI2CEN; + local_irq_enable(); pxa27x_device_i2c_power.dev.platform_data = info; } static struct platform_device *devices[] __initdata = { - &pxa_device_udc, + &pxa27x_device_udc, &pxa_device_ffuart, &pxa_device_btuart, &pxa_device_stuart, @@ -363,12 +358,16 @@ static struct platform_device *devices[] __initdata = { &pxa27x_device_ssp1, &pxa27x_device_ssp2, &pxa27x_device_ssp3, + &pxa27x_device_pwm0, + &pxa27x_device_pwm1, }; static struct sys_device pxa27x_sysdev[] = { { .cls = &pxa_irq_sysclass, }, { + .cls = &pxa2xx_mfp_sysclass, + }, { .cls = &pxa_gpio_sysclass, }, }; @@ -378,6 +377,9 @@ static int __init pxa27x_init(void) int i, ret = 0; if (cpu_is_pxa27x()) { + + reset_status = RCSR; + clks_register(pxa27x_clks, ARRAY_SIZE(pxa27x_clks)); if ((ret = pxa_init_dma(32))) diff --git a/arch/arm/mach-pxa/pxa2xx.c b/arch/arm/mach-pxa/pxa2xx.c new file mode 100644 index 00000000000..73d04d81c75 --- /dev/null +++ b/arch/arm/mach-pxa/pxa2xx.c @@ -0,0 +1,55 @@ +/* + * linux/arch/arm/mach-pxa/pxa2xx.c + * + * code specific to pxa2xx + * + * Copyright (C) 2008 Dmitry Baryshkov + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ + +#include <linux/module.h> +#include <linux/kernel.h> +#include <linux/device.h> + +#include <mach/hardware.h> +#include <mach/pxa2xx-regs.h> +#include <mach/mfp-pxa2xx.h> +#include <mach/mfp-pxa25x.h> +#include <mach/reset.h> +#include <mach/irda.h> + +void pxa2xx_clear_reset_status(unsigned int mask) +{ + /* RESET_STATUS_* has a 1:1 mapping with RCSR */ + RCSR = mask; +} + +static unsigned long pxa2xx_mfp_fir[] = { + GPIO46_FICP_RXD, + GPIO47_FICP_TXD, +}; + +static unsigned long pxa2xx_mfp_sir[] = { + GPIO46_STUART_RXD, + GPIO47_STUART_TXD, +}; + +static unsigned long pxa2xx_mfp_off[] = { + GPIO46_GPIO | MFP_LPM_DRIVE_LOW, + GPIO47_GPIO | MFP_LPM_DRIVE_LOW, +}; + +void pxa2xx_transceiver_mode(struct device *dev, int mode) +{ + if (mode & IR_OFF) { + pxa2xx_mfp_config(pxa2xx_mfp_off, ARRAY_SIZE(pxa2xx_mfp_off)); + } else if (mode & IR_SIRMODE) { + pxa2xx_mfp_config(pxa2xx_mfp_sir, ARRAY_SIZE(pxa2xx_mfp_sir)); + } else if (mode & IR_FIRMODE) { + pxa2xx_mfp_config(pxa2xx_mfp_fir, ARRAY_SIZE(pxa2xx_mfp_fir)); + } else + BUG(); +} diff --git a/arch/arm/mach-pxa/pxa300.c b/arch/arm/mach-pxa/pxa300.c index 0a0d3877f21..9adc7fc4618 100644 --- a/arch/arm/mach-pxa/pxa300.c +++ b/arch/arm/mach-pxa/pxa300.c @@ -15,9 +15,15 @@ #include <linux/module.h> #include <linux/kernel.h> +#include <linux/platform_device.h> -#include <asm/hardware.h> -#include <asm/arch/mfp-pxa300.h> +#include <mach/hardware.h> +#include <mach/pxa3xx-regs.h> +#include <mach/mfp-pxa300.h> + +#include "generic.h" +#include "devices.h" +#include "clock.h" static struct pxa3xx_mfp_addr_map pxa300_mfp_addr_map[] __initdata = { @@ -79,15 +85,28 @@ static struct pxa3xx_mfp_addr_map pxa310_mfp_addr_map[] __initdata = { MFP_ADDR_END, }; +static struct clk common_clks[] = { + PXA3xx_CKEN("NANDCLK", NAND, 156000000, 0, &pxa3xx_device_nand.dev), +}; + +static struct clk pxa310_clks[] = { +#ifdef CONFIG_CPU_PXA310 + PXA3xx_CKEN("MMCCLK", MMC3, 19500000, 0, &pxa3xx_device_mci3.dev), +#endif +}; + static int __init pxa300_init(void) { if (cpu_is_pxa300() || cpu_is_pxa310()) { pxa3xx_init_mfp(); pxa3xx_mfp_init_addr(pxa300_mfp_addr_map); + clks_register(ARRAY_AND_SIZE(common_clks)); } - if (cpu_is_pxa310()) + if (cpu_is_pxa310()) { pxa3xx_mfp_init_addr(pxa310_mfp_addr_map); + clks_register(ARRAY_AND_SIZE(pxa310_clks)); + } return 0; } diff --git a/arch/arm/mach-pxa/pxa320.c b/arch/arm/mach-pxa/pxa320.c index 74128eb8f8d..016eb18f01a 100644 --- a/arch/arm/mach-pxa/pxa320.c +++ b/arch/arm/mach-pxa/pxa320.c @@ -15,10 +15,16 @@ #include <linux/module.h> #include <linux/kernel.h> +#include <linux/platform_device.h> -#include <asm/hardware.h> -#include <asm/arch/mfp.h> -#include <asm/arch/mfp-pxa320.h> +#include <mach/hardware.h> +#include <mach/mfp.h> +#include <mach/pxa3xx-regs.h> +#include <mach/mfp-pxa320.h> + +#include "generic.h" +#include "devices.h" +#include "clock.h" static struct pxa3xx_mfp_addr_map pxa320_mfp_addr_map[] __initdata = { @@ -74,16 +80,17 @@ static struct pxa3xx_mfp_addr_map pxa320_mfp_addr_map[] __initdata = { MFP_ADDR_END, }; -static void __init pxa320_init_mfp(void) -{ - pxa3xx_init_mfp(); - pxa3xx_mfp_init_addr(pxa320_mfp_addr_map); -} +static struct clk pxa320_clks[] = { + PXA3xx_CKEN("NANDCLK", NAND, 104000000, 0, &pxa3xx_device_nand.dev), +}; static int __init pxa320_init(void) { - if (cpu_is_pxa320()) - pxa320_init_mfp(); + if (cpu_is_pxa320()) { + pxa3xx_init_mfp(); + pxa3xx_mfp_init_addr(pxa320_mfp_addr_map); + clks_register(ARRAY_AND_SIZE(pxa320_clks)); + } return 0; } diff --git a/arch/arm/mach-pxa/pxa3xx.c b/arch/arm/mach-pxa/pxa3xx.c index 644550bfa33..b3cd5d0b0f3 100644 --- a/arch/arm/mach-pxa/pxa3xx.c +++ b/arch/arm/mach-pxa/pxa3xx.c @@ -22,12 +22,13 @@ #include <linux/io.h> #include <linux/sysdev.h> -#include <asm/hardware.h> -#include <asm/arch/pxa3xx-regs.h> -#include <asm/arch/ohci.h> -#include <asm/arch/pm.h> -#include <asm/arch/dma.h> -#include <asm/arch/ssp.h> +#include <mach/hardware.h> +#include <mach/pxa3xx-regs.h> +#include <mach/reset.h> +#include <mach/ohci.h> +#include <mach/pm.h> +#include <mach/dma.h> +#include <mach/ssp.h> #include "generic.h" #include "devices.h" @@ -109,6 +110,12 @@ unsigned int pxa3xx_get_memclk_frequency_10khz(void) return (clk / 10000); } +void pxa3xx_clear_reset_status(unsigned int mask) +{ + /* RESET_STATUS_* has a 1:1 mapping with ARSR */ + ARSR = mask; +} + /* * Return the current AC97 clock frequency. */ @@ -144,7 +151,7 @@ static unsigned long clk_pxa3xx_hsio_getrate(struct clk *clk) return hsio_clk; } -static void clk_pxa3xx_cken_enable(struct clk *clk) +void clk_pxa3xx_cken_enable(struct clk *clk) { unsigned long mask = 1ul << (clk->cken & 0x1f); @@ -154,7 +161,7 @@ static void clk_pxa3xx_cken_enable(struct clk *clk) CKENB |= mask; } -static void clk_pxa3xx_cken_disable(struct clk *clk) +void clk_pxa3xx_cken_disable(struct clk *clk) { unsigned long mask = 1ul << (clk->cken & 0x1f); @@ -164,7 +171,7 @@ static void clk_pxa3xx_cken_disable(struct clk *clk) CKENB &= ~mask; } -static const struct clkops clk_pxa3xx_cken_ops = { +const struct clkops clk_pxa3xx_cken_ops = { .enable = clk_pxa3xx_cken_enable, .disable = clk_pxa3xx_cken_disable, }; @@ -196,23 +203,18 @@ static const struct clkops clk_pout_ops = { .disable = clk_pout_disable, }; -#define PXA3xx_CKEN(_name, _cken, _rate, _delay, _dev) \ - { \ - .name = _name, \ - .dev = _dev, \ - .ops = &clk_pxa3xx_cken_ops, \ - .rate = _rate, \ - .cken = CKEN_##_cken, \ - .delay = _delay, \ - } +static void clk_dummy_enable(struct clk *clk) +{ +} -#define PXA3xx_CK(_name, _cken, _ops, _dev) \ - { \ - .name = _name, \ - .dev = _dev, \ - .ops = _ops, \ - .cken = CKEN_##_cken, \ - } +static void clk_dummy_disable(struct clk *clk) +{ +} + +static const struct clkops clk_dummy_ops = { + .enable = clk_dummy_enable, + .disable = clk_dummy_disable, +}; static struct clk pxa3xx_clks[] = { { @@ -222,6 +224,13 @@ static struct clk pxa3xx_clks[] = { .delay = 70, }, + /* Power I2C clock is always on */ + { + .name = "I2CCLK", + .ops = &clk_dummy_ops, + .dev = &pxa3xx_device_i2c_power.dev, + }, + PXA3xx_CK("LCDCLK", LCD, &clk_pxa3xx_hsio_ops, &pxa_device_fb.dev), PXA3xx_CK("CAMCLK", CAMERA, &clk_pxa3xx_hsio_ops, NULL), PXA3xx_CK("AC97CLK", AC97, &clk_pxa3xx_ac97_ops, NULL), @@ -231,7 +240,7 @@ static struct clk pxa3xx_clks[] = { PXA3xx_CKEN("UARTCLK", STUART, 14857000, 1, NULL), PXA3xx_CKEN("I2CCLK", I2C, 32842000, 0, &pxa_device_i2c.dev), - PXA3xx_CKEN("UDCCLK", UDC, 48000000, 5, &pxa_device_udc.dev), + PXA3xx_CKEN("UDCCLK", UDC, 48000000, 5, &pxa27x_device_udc.dev), PXA3xx_CKEN("USBCLK", USBH, 48000000, 0, &pxa27x_device_ohci.dev), PXA3xx_CKEN("KBDCLK", KEYPAD, 32768, 0, &pxa27x_device_keypad.dev), @@ -239,10 +248,11 @@ static struct clk pxa3xx_clks[] = { PXA3xx_CKEN("SSPCLK", SSP2, 13000000, 0, &pxa27x_device_ssp2.dev), PXA3xx_CKEN("SSPCLK", SSP3, 13000000, 0, &pxa27x_device_ssp3.dev), PXA3xx_CKEN("SSPCLK", SSP4, 13000000, 0, &pxa3xx_device_ssp4.dev), + PXA3xx_CKEN("PWMCLK", PWM0, 13000000, 0, &pxa27x_device_pwm0.dev), + PXA3xx_CKEN("PWMCLK", PWM1, 13000000, 0, &pxa27x_device_pwm1.dev), PXA3xx_CKEN("MMCCLK", MMC1, 19500000, 0, &pxa_device_mci.dev), PXA3xx_CKEN("MMCCLK", MMC2, 19500000, 0, &pxa3xx_device_mci2.dev), - PXA3xx_CKEN("MMCCLK", MMC3, 19500000, 0, &pxa3xx_device_mci3.dev), }; #ifdef CONFIG_PM @@ -519,8 +529,32 @@ void __init pxa3xx_init_irq(void) * device registration specific to PXA3xx. */ +static struct resource i2c_power_resources[] = { + { + .start = 0x40f500c0, + .end = 0x40f500d3, + .flags = IORESOURCE_MEM, + }, { + .start = IRQ_PWRI2C, + .end = IRQ_PWRI2C, + .flags = IORESOURCE_IRQ, + }, +}; + +struct platform_device pxa3xx_device_i2c_power = { + .name = "pxa2xx-i2c", + .id = 1, + .resource = i2c_power_resources, + .num_resources = ARRAY_SIZE(i2c_power_resources), +}; + +void __init pxa3xx_set_i2c_power_info(struct i2c_pxa_platform_data *info) +{ + pxa3xx_device_i2c_power.dev.platform_data = info; +} + static struct platform_device *devices[] __initdata = { - &pxa_device_udc, +/* &pxa_device_udc, The UDC driver is PXA25x only */ &pxa_device_ffuart, &pxa_device_btuart, &pxa_device_stuart, @@ -530,6 +564,9 @@ static struct platform_device *devices[] __initdata = { &pxa27x_device_ssp2, &pxa27x_device_ssp3, &pxa3xx_device_ssp4, + &pxa27x_device_pwm0, + &pxa27x_device_pwm1, + &pxa3xx_device_i2c_power, }; static struct sys_device pxa3xx_sysdev[] = { @@ -547,6 +584,9 @@ static int __init pxa3xx_init(void) int i, ret = 0; if (cpu_is_pxa3xx()) { + + reset_status = ARSR; + /* * clear RDH bit every time after reset * diff --git a/arch/arm/mach-pxa/pxa930.c b/arch/arm/mach-pxa/pxa930.c new file mode 100644 index 00000000000..13e6bfdfff6 --- /dev/null +++ b/arch/arm/mach-pxa/pxa930.c @@ -0,0 +1,190 @@ +/* + * linux/arch/arm/mach-pxa/pxa930.c + * + * Code specific to PXA930 + * + * Copyright (C) 2007-2008 Marvell Internation Ltd. + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ + +#include <linux/module.h> +#include <linux/kernel.h> +#include <linux/platform_device.h> +#include <linux/irq.h> +#include <linux/dma-mapping.h> + +#include <mach/hardware.h> +#include <mach/mfp-pxa930.h> + +static struct pxa3xx_mfp_addr_map pxa930_mfp_addr_map[] __initdata = { + + MFP_ADDR(GPIO0, 0x02e0), + MFP_ADDR(GPIO1, 0x02dc), + MFP_ADDR(GPIO2, 0x02e8), + MFP_ADDR(GPIO3, 0x02d8), + MFP_ADDR(GPIO4, 0x02e4), + MFP_ADDR(GPIO5, 0x02ec), + MFP_ADDR(GPIO6, 0x02f8), + MFP_ADDR(GPIO7, 0x02fc), + MFP_ADDR(GPIO8, 0x0300), + MFP_ADDR(GPIO9, 0x02d4), + MFP_ADDR(GPIO10, 0x02f4), + MFP_ADDR(GPIO11, 0x02f0), + MFP_ADDR(GPIO12, 0x0304), + MFP_ADDR(GPIO13, 0x0310), + MFP_ADDR(GPIO14, 0x0308), + MFP_ADDR(GPIO15, 0x030c), + MFP_ADDR(GPIO16, 0x04e8), + MFP_ADDR(GPIO17, 0x04f4), + MFP_ADDR(GPIO18, 0x04f8), + MFP_ADDR(GPIO19, 0x04fc), + MFP_ADDR(GPIO20, 0x0518), + MFP_ADDR(GPIO21, 0x051c), + MFP_ADDR(GPIO22, 0x04ec), + MFP_ADDR(GPIO23, 0x0500), + MFP_ADDR(GPIO24, 0x04f0), + MFP_ADDR(GPIO25, 0x0504), + MFP_ADDR(GPIO26, 0x0510), + MFP_ADDR(GPIO27, 0x0514), + MFP_ADDR(GPIO28, 0x0520), + MFP_ADDR(GPIO29, 0x0600), + MFP_ADDR(GPIO30, 0x0618), + MFP_ADDR(GPIO31, 0x0610), + MFP_ADDR(GPIO32, 0x060c), + MFP_ADDR(GPIO33, 0x061c), + MFP_ADDR(GPIO34, 0x0620), + MFP_ADDR(GPIO35, 0x0628), + MFP_ADDR(GPIO36, 0x062c), + MFP_ADDR(GPIO37, 0x0630), + MFP_ADDR(GPIO38, 0x0634), + MFP_ADDR(GPIO39, 0x0638), + MFP_ADDR(GPIO40, 0x063c), + MFP_ADDR(GPIO41, 0x0614), + MFP_ADDR(GPIO42, 0x0624), + MFP_ADDR(GPIO43, 0x0608), + MFP_ADDR(GPIO44, 0x0604), + MFP_ADDR(GPIO45, 0x050c), + MFP_ADDR(GPIO46, 0x0508), + MFP_ADDR(GPIO47, 0x02bc), + MFP_ADDR(GPIO48, 0x02b4), + MFP_ADDR(GPIO49, 0x02b8), + MFP_ADDR(GPIO50, 0x02c8), + MFP_ADDR(GPIO51, 0x02c0), + MFP_ADDR(GPIO52, 0x02c4), + MFP_ADDR(GPIO53, 0x02d0), + MFP_ADDR(GPIO54, 0x02cc), + MFP_ADDR(GPIO55, 0x029c), + MFP_ADDR(GPIO56, 0x02a0), + MFP_ADDR(GPIO57, 0x0294), + MFP_ADDR(GPIO58, 0x0298), + MFP_ADDR(GPIO59, 0x02a4), + MFP_ADDR(GPIO60, 0x02a8), + MFP_ADDR(GPIO61, 0x02b0), + MFP_ADDR(GPIO62, 0x02ac), + MFP_ADDR(GPIO63, 0x0640), + MFP_ADDR(GPIO64, 0x065c), + MFP_ADDR(GPIO65, 0x0648), + MFP_ADDR(GPIO66, 0x0644), + MFP_ADDR(GPIO67, 0x0674), + MFP_ADDR(GPIO68, 0x0658), + MFP_ADDR(GPIO69, 0x0654), + MFP_ADDR(GPIO70, 0x0660), + MFP_ADDR(GPIO71, 0x0668), + MFP_ADDR(GPIO72, 0x0664), + MFP_ADDR(GPIO73, 0x0650), + MFP_ADDR(GPIO74, 0x066c), + MFP_ADDR(GPIO75, 0x064c), + MFP_ADDR(GPIO76, 0x0670), + MFP_ADDR(GPIO77, 0x0678), + MFP_ADDR(GPIO78, 0x067c), + MFP_ADDR(GPIO79, 0x0694), + MFP_ADDR(GPIO80, 0x069c), + MFP_ADDR(GPIO81, 0x06a0), + MFP_ADDR(GPIO82, 0x06a4), + MFP_ADDR(GPIO83, 0x0698), + MFP_ADDR(GPIO84, 0x06bc), + MFP_ADDR(GPIO85, 0x06b4), + MFP_ADDR(GPIO86, 0x06b0), + MFP_ADDR(GPIO87, 0x06c0), + MFP_ADDR(GPIO88, 0x06c4), + MFP_ADDR(GPIO89, 0x06ac), + MFP_ADDR(GPIO90, 0x0680), + MFP_ADDR(GPIO91, 0x0684), + MFP_ADDR(GPIO92, 0x0688), + MFP_ADDR(GPIO93, 0x0690), + MFP_ADDR(GPIO94, 0x068c), + MFP_ADDR(GPIO95, 0x06a8), + MFP_ADDR(GPIO96, 0x06b8), + MFP_ADDR(GPIO97, 0x0410), + MFP_ADDR(GPIO98, 0x0418), + MFP_ADDR(GPIO99, 0x041c), + MFP_ADDR(GPIO100, 0x0414), + MFP_ADDR(GPIO101, 0x0408), + MFP_ADDR(GPIO102, 0x0324), + MFP_ADDR(GPIO103, 0x040c), + MFP_ADDR(GPIO104, 0x0400), + MFP_ADDR(GPIO105, 0x0328), + MFP_ADDR(GPIO106, 0x0404), + + MFP_ADDR(nXCVREN, 0x0204), + MFP_ADDR(DF_CLE_nOE, 0x020c), + MFP_ADDR(DF_nADV1_ALE, 0x0218), + MFP_ADDR(DF_SCLK_E, 0x0214), + MFP_ADDR(DF_SCLK_S, 0x0210), + MFP_ADDR(nBE0, 0x021c), + MFP_ADDR(nBE1, 0x0220), + MFP_ADDR(DF_nADV2_ALE, 0x0224), + MFP_ADDR(DF_INT_RnB, 0x0228), + MFP_ADDR(DF_nCS0, 0x022c), + MFP_ADDR(DF_nCS1, 0x0230), + MFP_ADDR(nLUA, 0x0254), + MFP_ADDR(nLLA, 0x0258), + MFP_ADDR(DF_nWE, 0x0234), + MFP_ADDR(DF_nRE_nOE, 0x0238), + MFP_ADDR(DF_ADDR0, 0x024c), + MFP_ADDR(DF_ADDR1, 0x0250), + MFP_ADDR(DF_ADDR2, 0x025c), + MFP_ADDR(DF_ADDR3, 0x0260), + MFP_ADDR(DF_IO0, 0x023c), + MFP_ADDR(DF_IO1, 0x0240), + MFP_ADDR(DF_IO2, 0x0244), + MFP_ADDR(DF_IO3, 0x0248), + MFP_ADDR(DF_IO4, 0x0264), + MFP_ADDR(DF_IO5, 0x0268), + MFP_ADDR(DF_IO6, 0x026c), + MFP_ADDR(DF_IO7, 0x0270), + MFP_ADDR(DF_IO8, 0x0274), + MFP_ADDR(DF_IO9, 0x0278), + MFP_ADDR(DF_IO10, 0x027c), + MFP_ADDR(DF_IO11, 0x0280), + MFP_ADDR(DF_IO12, 0x0284), + MFP_ADDR(DF_IO13, 0x0288), + MFP_ADDR(DF_IO14, 0x028c), + MFP_ADDR(DF_IO15, 0x0290), + + MFP_ADDR(GSIM_UIO, 0x0314), + MFP_ADDR(GSIM_UCLK, 0x0318), + MFP_ADDR(GSIM_UDET, 0x031c), + MFP_ADDR(GSIM_nURST, 0x0320), + + MFP_ADDR(PMIC_INT, 0x06c8), + + MFP_ADDR(RDY, 0x0200), + + MFP_ADDR_END, +}; + +static int __init pxa930_init(void) +{ + if (cpu_is_pxa930()) { + pxa3xx_init_mfp(); + pxa3xx_mfp_init_addr(pxa930_mfp_addr_map); + } + + return 0; +} + +core_initcall(pxa930_init); diff --git a/arch/arm/mach-pxa/reset.c b/arch/arm/mach-pxa/reset.c new file mode 100644 index 00000000000..1b2af575c40 --- /dev/null +++ b/arch/arm/mach-pxa/reset.c @@ -0,0 +1,101 @@ +/* + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ +#include <linux/kernel.h> +#include <linux/module.h> +#include <linux/delay.h> +#include <linux/gpio.h> +#include <linux/io.h> +#include <asm/proc-fns.h> + +#include <mach/pxa-regs.h> +#include <mach/reset.h> + +unsigned int reset_status; +EXPORT_SYMBOL(reset_status); + +static void do_hw_reset(void); + +static int reset_gpio = -1; + +int init_gpio_reset(int gpio, int output) +{ + int rc; + + rc = gpio_request(gpio, "reset generator"); + if (rc) { + printk(KERN_ERR "Can't request reset_gpio\n"); + goto out; + } + + if (output) + rc = gpio_direction_output(gpio, 0); + else + rc = gpio_direction_input(gpio); + if (rc) { + printk(KERN_ERR "Can't configure reset_gpio\n"); + gpio_free(gpio); + goto out; + } + +out: + if (!rc) + reset_gpio = gpio; + + return rc; +} + +/* + * Trigger GPIO reset. + * This covers various types of logic connecting gpio pin + * to RESET pins (nRESET or GPIO_RESET): + */ +static void do_gpio_reset(void) +{ + BUG_ON(reset_gpio == -1); + + /* drive it low */ + gpio_direction_output(reset_gpio, 0); + mdelay(2); + /* rising edge or drive high */ + gpio_set_value(reset_gpio, 1); + mdelay(2); + /* falling edge */ + gpio_set_value(reset_gpio, 0); + + /* give it some time */ + mdelay(10); + + WARN_ON(1); + /* fallback */ + do_hw_reset(); +} + +static void do_hw_reset(void) +{ + /* Initialize the watchdog and let it fire */ + OWER = OWER_WME; + OSSR = OSSR_M3; + OSMR3 = OSCR + 368640; /* ... in 100 ms */ +} + +void arch_reset(char mode) +{ + clear_reset_status(RESET_STATUS_ALL); + + switch (mode) { + case 's': + /* Jump into ROM at address 0 */ + cpu_reset(0); + break; + case 'h': + do_hw_reset(); + break; + case 'g': + do_gpio_reset(); + break; + } +} + diff --git a/arch/arm/mach-pxa/saar.c b/arch/arm/mach-pxa/saar.c new file mode 100644 index 00000000000..e7ea91ce7f0 --- /dev/null +++ b/arch/arm/mach-pxa/saar.c @@ -0,0 +1,84 @@ +/* + * linux/arch/arm/mach-pxa/saar.c + * + * Support for the Marvell PXA930 Handheld Platform (aka SAAR) + * + * Copyright (C) 2007-2008 Marvell International Ltd. + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * publishhed by the Free Software Foundation. + */ + +#include <linux/module.h> +#include <linux/kernel.h> +#include <linux/interrupt.h> +#include <linux/init.h> +#include <linux/platform_device.h> +#include <linux/clk.h> +#include <linux/gpio.h> +#include <linux/smc91x.h> + +#include <asm/mach-types.h> +#include <asm/mach/arch.h> +#include <mach/hardware.h> +#include <mach/pxa3xx-regs.h> +#include <mach/mfp-pxa930.h> + +#include "devices.h" +#include "generic.h" + +/* SAAR MFP configurations */ +static mfp_cfg_t saar_mfp_cfg[] __initdata = { + /* Ethernet */ + DF_nCS1_nCS3, + GPIO97_GPIO, +}; + +#define SAAR_ETH_PHYS (0x14000000) + +static struct resource smc91x_resources[] = { + [0] = { + .start = (SAAR_ETH_PHYS + 0x300), + .end = (SAAR_ETH_PHYS + 0xfffff), + .flags = IORESOURCE_MEM, + }, + [1] = { + .start = gpio_to_irq(mfp_to_gpio(MFP_PIN_GPIO97)), + .end = gpio_to_irq(mfp_to_gpio(MFP_PIN_GPIO97)), + .flags = IORESOURCE_IRQ | IORESOURCE_IRQ_HIGHEDGE, + } +}; + +static struct smc91x_platdata saar_smc91x_info = { + .flags = SMC91X_USE_16BIT | SMC91X_NOWAIT | SMC91X_USE_DMA, +}; + +static struct platform_device smc91x_device = { + .name = "smc91x", + .id = 0, + .num_resources = ARRAY_SIZE(smc91x_resources), + .resource = smc91x_resources, + .dev = { + .platform_data = &saar_smc91x_info, + }, +}; + +static void __init saar_init(void) +{ + /* initialize MFP configurations */ + pxa3xx_mfp_config(ARRAY_AND_SIZE(saar_mfp_cfg)); + + platform_device_register(&smc91x_device); +} + +MACHINE_START(SAAR, "PXA930 Handheld Platform (aka SAAR)") + /* Maintainer: Eric Miao <eric.miao@marvell.com> */ + .phys_io = 0x40000000, + .boot_params = 0xa0000100, + .io_pg_offst = (io_p2v(0x40000000) >> 18) & 0xfffc, + .map_io = pxa_map_io, + .init_irq = pxa3xx_init_irq, + .timer = &pxa_timer, + .init_machine = saar_init, +MACHINE_END diff --git a/arch/arm/mach-pxa/sharpsl_pm.c b/arch/arm/mach-pxa/sharpsl_pm.c index 34cd585075b..15c2f1a8623 100644 --- a/arch/arm/mach-pxa/sharpsl_pm.c +++ b/arch/arm/mach-pxa/sharpsl_pm.c @@ -22,12 +22,12 @@ #include <linux/platform_device.h> #include <linux/apm-emulation.h> -#include <asm/hardware.h> +#include <mach/hardware.h> #include <asm/mach-types.h> -#include <asm/arch/pm.h> -#include <asm/arch/pxa-regs.h> -#include <asm/arch/pxa2xx-gpio.h> -#include <asm/arch/sharpsl.h> +#include <mach/pm.h> +#include <mach/pxa-regs.h> +#include <mach/pxa2xx-gpio.h> +#include <mach/sharpsl.h> #include "sharpsl.h" struct battery_thresh spitz_battery_levels_acin[] = { @@ -116,24 +116,20 @@ struct battery_thresh spitz_battery_levels_noac[] = { { 0, 0}, }; -/* MAX1111 Commands */ -#define MAXCTRL_PD0 1u << 0 -#define MAXCTRL_PD1 1u << 1 -#define MAXCTRL_SGL 1u << 2 -#define MAXCTRL_UNI 1u << 3 -#define MAXCTRL_SEL_SH 4 -#define MAXCTRL_STR 1u << 7 - /* * Read MAX1111 ADC */ +extern int max1111_read_channel(int); + int sharpsl_pm_pxa_read_max1111(int channel) { if (machine_is_tosa()) // Ugly, better move this function into another module return 0; - return corgi_ssp_max1111_get((channel << MAXCTRL_SEL_SH) | MAXCTRL_PD0 | MAXCTRL_PD1 - | MAXCTRL_SGL | MAXCTRL_UNI | MAXCTRL_STR); + /* max1111 accepts channels from 0-3, however, + * it is encoded from 0-7 here in the code. + */ + return max1111_read_channel(channel >> 1); } void sharpsl_pm_pxa_init(void) @@ -146,18 +142,18 @@ void sharpsl_pm_pxa_init(void) if (request_irq(IRQ_GPIO(sharpsl_pm.machinfo->gpio_acin), sharpsl_ac_isr, IRQF_DISABLED, "AC Input Detect", sharpsl_ac_isr)) { dev_err(sharpsl_pm.dev, "Could not get irq %d.\n", IRQ_GPIO(sharpsl_pm.machinfo->gpio_acin)); } - else set_irq_type(IRQ_GPIO(sharpsl_pm.machinfo->gpio_acin),IRQT_BOTHEDGE); + else set_irq_type(IRQ_GPIO(sharpsl_pm.machinfo->gpio_acin),IRQ_TYPE_EDGE_BOTH); if (request_irq(IRQ_GPIO(sharpsl_pm.machinfo->gpio_batlock), sharpsl_fatal_isr, IRQF_DISABLED, "Battery Cover", sharpsl_fatal_isr)) { dev_err(sharpsl_pm.dev, "Could not get irq %d.\n", IRQ_GPIO(sharpsl_pm.machinfo->gpio_batlock)); } - else set_irq_type(IRQ_GPIO(sharpsl_pm.machinfo->gpio_batlock),IRQT_FALLING); + else set_irq_type(IRQ_GPIO(sharpsl_pm.machinfo->gpio_batlock),IRQ_TYPE_EDGE_FALLING); if (sharpsl_pm.machinfo->gpio_fatal) { if (request_irq(IRQ_GPIO(sharpsl_pm.machinfo->gpio_fatal), sharpsl_fatal_isr, IRQF_DISABLED, "Fatal Battery", sharpsl_fatal_isr)) { dev_err(sharpsl_pm.dev, "Could not get irq %d.\n", IRQ_GPIO(sharpsl_pm.machinfo->gpio_fatal)); } - else set_irq_type(IRQ_GPIO(sharpsl_pm.machinfo->gpio_fatal),IRQT_FALLING); + else set_irq_type(IRQ_GPIO(sharpsl_pm.machinfo->gpio_fatal),IRQ_TYPE_EDGE_FALLING); } if (sharpsl_pm.machinfo->batfull_irq) @@ -166,7 +162,7 @@ void sharpsl_pm_pxa_init(void) if (request_irq(IRQ_GPIO(sharpsl_pm.machinfo->gpio_batfull), sharpsl_chrg_full_isr, IRQF_DISABLED, "CO", sharpsl_chrg_full_isr)) { dev_err(sharpsl_pm.dev, "Could not get irq %d.\n", IRQ_GPIO(sharpsl_pm.machinfo->gpio_batfull)); } - else set_irq_type(IRQ_GPIO(sharpsl_pm.machinfo->gpio_batfull),IRQT_RISING); + else set_irq_type(IRQ_GPIO(sharpsl_pm.machinfo->gpio_batfull),IRQ_TYPE_EDGE_RISING); } } diff --git a/arch/arm/mach-pxa/sleep.S b/arch/arm/mach-pxa/sleep.S index 784716eb7fc..a62c8375eb5 100644 --- a/arch/arm/mach-pxa/sleep.S +++ b/arch/arm/mach-pxa/sleep.S @@ -13,10 +13,10 @@ #include <linux/linkage.h> #include <asm/assembler.h> -#include <asm/hardware.h> +#include <mach/hardware.h> -#include <asm/arch/pxa-regs.h> -#include <asm/arch/pxa2xx-regs.h> +#include <mach/pxa-regs.h> +#include <mach/pxa2xx-regs.h> #define MDREFR_KDIV 0x200a4000 // all banks #define CCCR_SLEEP 0x00000107 // L=7 2N=2 A=0 PPDIS=0 CPDIS=0 diff --git a/arch/arm/mach-pxa/spitz.c b/arch/arm/mach-pxa/spitz.c index e7d0fcd9b43..524f656dc56 100644 --- a/arch/arm/mach-pxa/spitz.c +++ b/arch/arm/mach-pxa/spitz.c @@ -19,33 +19,43 @@ #include <linux/major.h> #include <linux/fs.h> #include <linux/interrupt.h> +#include <linux/gpio.h> +#include <linux/leds.h> #include <linux/mmc/host.h> #include <linux/pm.h> #include <linux/backlight.h> +#include <linux/io.h> +#include <linux/i2c.h> +#include <linux/i2c/pca953x.h> +#include <linux/spi/spi.h> +#include <linux/spi/ads7846.h> +#include <linux/spi/corgi_lcd.h> #include <asm/setup.h> #include <asm/memory.h> #include <asm/mach-types.h> -#include <asm/hardware.h> +#include <mach/hardware.h> #include <asm/irq.h> -#include <asm/io.h> #include <asm/system.h> #include <asm/mach/arch.h> #include <asm/mach/map.h> #include <asm/mach/irq.h> -#include <asm/arch/pxa-regs.h> -#include <asm/arch/pxa2xx-regs.h> -#include <asm/arch/pxa2xx-gpio.h> -#include <asm/arch/irda.h> -#include <asm/arch/mmc.h> -#include <asm/arch/ohci.h> -#include <asm/arch/udc.h> -#include <asm/arch/pxafb.h> -#include <asm/arch/akita.h> -#include <asm/arch/spitz.h> -#include <asm/arch/sharpsl.h> +#include <mach/pxa-regs.h> +#include <mach/pxa2xx-regs.h> +#include <mach/mfp-pxa27x.h> +#include <mach/pxa27x-udc.h> +#include <mach/reset.h> +#include <mach/i2c.h> +#include <mach/irda.h> +#include <mach/mmc.h> +#include <mach/ohci.h> +#include <mach/udc.h> +#include <mach/pxafb.h> +#include <mach/pxa2xx_spi.h> +#include <mach/spitz.h> +#include <mach/sharpsl.h> #include <asm/mach/sharpsl_param.h> #include <asm/hardware/scoop.h> @@ -54,6 +64,66 @@ #include "devices.h" #include "sharpsl.h" +static unsigned long spitz_pin_config[] __initdata = { + /* Chip Selects */ + GPIO78_nCS_2, /* SCOOP #2 */ + GPIO80_nCS_4, /* SCOOP #1 */ + + /* LCD - 16bpp Active TFT */ + GPIO58_LCD_LDD_0, + GPIO59_LCD_LDD_1, + GPIO60_LCD_LDD_2, + GPIO61_LCD_LDD_3, + GPIO62_LCD_LDD_4, + GPIO63_LCD_LDD_5, + GPIO64_LCD_LDD_6, + GPIO65_LCD_LDD_7, + GPIO66_LCD_LDD_8, + GPIO67_LCD_LDD_9, + GPIO68_LCD_LDD_10, + GPIO69_LCD_LDD_11, + GPIO70_LCD_LDD_12, + GPIO71_LCD_LDD_13, + GPIO72_LCD_LDD_14, + GPIO73_LCD_LDD_15, + GPIO74_LCD_FCLK, + GPIO75_LCD_LCLK, + GPIO76_LCD_PCLK, + + /* PC Card */ + GPIO48_nPOE, + GPIO49_nPWE, + GPIO50_nPIOR, + GPIO51_nPIOW, + GPIO85_nPCE_1, + GPIO54_nPCE_2, + GPIO79_PSKTSEL, + GPIO55_nPREG, + GPIO56_nPWAIT, + GPIO57_nIOIS16, + + /* MMC */ + GPIO32_MMC_CLK, + GPIO112_MMC_CMD, + GPIO92_MMC_DAT_0, + GPIO109_MMC_DAT_1, + GPIO110_MMC_DAT_2, + GPIO111_MMC_DAT_3, + + /* GPIOs */ + GPIO9_GPIO, /* SPITZ_GPIO_nSD_DETECT */ + GPIO81_GPIO, /* SPITZ_GPIO_nSD_WP */ + GPIO41_GPIO, /* SPITZ_GPIO_USB_CONNECT */ + GPIO37_GPIO, /* SPITZ_GPIO_USB_HOST */ + GPIO35_GPIO, /* SPITZ_GPIO_USB_DEVICE */ + GPIO22_GPIO, /* SPITZ_GPIO_HSYNC */ + GPIO94_GPIO, /* SPITZ_GPIO_CF_CD */ + GPIO105_GPIO, /* SPITZ_GPIO_CF_IRQ */ + GPIO106_GPIO, /* SPITZ_GPIO_CF2_IRQ */ + + GPIO1_GPIO | WAKEUP_ON_EDGE_RISE, +}; + /* * Spitz SCOOP Device #1 */ @@ -66,10 +136,11 @@ static struct resource spitz_scoop_resources[] = { }; static struct scoop_config spitz_scoop_setup = { - .io_dir = SPITZ_SCP_IO_DIR, + .io_dir = SPITZ_SCP_IO_DIR, .io_out = SPITZ_SCP_IO_OUT, - .suspend_clr = SPITZ_SCP_SUS_CLR, - .suspend_set = SPITZ_SCP_SUS_SET, + .suspend_clr = SPITZ_SCP_SUS_CLR, + .suspend_set = SPITZ_SCP_SUS_SET, + .gpio_base = SPITZ_SCP_GPIO_BASE, }; struct platform_device spitzscoop_device = { @@ -94,10 +165,11 @@ static struct resource spitz_scoop2_resources[] = { }; static struct scoop_config spitz_scoop2_setup = { - .io_dir = SPITZ_SCP2_IO_DIR, + .io_dir = SPITZ_SCP2_IO_DIR, .io_out = SPITZ_SCP2_IO_OUT, - .suspend_clr = SPITZ_SCP2_SUS_CLR, - .suspend_set = SPITZ_SCP2_SUS_SET, + .suspend_clr = SPITZ_SCP2_SUS_CLR, + .suspend_set = SPITZ_SCP2_SUS_SET, + .gpio_base = SPITZ_SCP2_GPIO_BASE, }; struct platform_device spitzscoop2_device = { @@ -119,7 +191,7 @@ static void spitz_card_pwr_ctrl(int device, unsigned short new_cpr) unsigned short cpr = read_scoop_reg(&spitzscoop_device.dev, SCOOP_CPR); if (new_cpr & 0x0007) { - set_scoop_gpio(&spitzscoop_device.dev, SPITZ_SCP_CF_POWER); + gpio_set_value(SPITZ_GPIO_CF_POWER, 1); if (!(cpr & 0x0002) && !(cpr & 0x0004)) mdelay(5); if (device == SPITZ_PWR_CF) @@ -135,34 +207,13 @@ static void spitz_card_pwr_ctrl(int device, unsigned short new_cpr) if (!(cpr & 0x0002) && !(cpr & 0x0004)) { write_scoop_reg(&spitzscoop_device.dev, SCOOP_CPR, 0x0000); mdelay(1); - reset_scoop_gpio(&spitzscoop_device.dev, SPITZ_SCP_CF_POWER); + gpio_set_value(SPITZ_GPIO_CF_POWER, 0); } else { write_scoop_reg(&spitzscoop_device.dev, SCOOP_CPR, cpr | new_cpr); } } } -static void spitz_pcmcia_init(void) -{ - /* Setup default state of GPIO outputs - before we enable them as outputs. */ - GPSR(GPIO48_nPOE) = GPIO_bit(GPIO48_nPOE) | - GPIO_bit(GPIO49_nPWE) | GPIO_bit(GPIO50_nPIOR) | - GPIO_bit(GPIO51_nPIOW) | GPIO_bit(GPIO54_nPCE_2); - GPSR(GPIO85_nPCE_1) = GPIO_bit(GPIO85_nPCE_1); - - pxa_gpio_mode(GPIO48_nPOE_MD); - pxa_gpio_mode(GPIO49_nPWE_MD); - pxa_gpio_mode(GPIO50_nPIOR_MD); - pxa_gpio_mode(GPIO51_nPIOW_MD); - pxa_gpio_mode(GPIO55_nPREG_MD); - pxa_gpio_mode(GPIO56_nPWAIT_MD); - pxa_gpio_mode(GPIO57_nIOIS16_MD); - pxa_gpio_mode(GPIO85_nPCE_1_MD); - pxa_gpio_mode(GPIO54_nPCE_2_MD); - pxa_gpio_mode(GPIO104_pSKTSEL_MD); -} - static void spitz_pcmcia_pwr(struct device *scoop, unsigned short cpr, int nr) { /* Only need to override behaviour for slot 0 */ @@ -188,165 +239,169 @@ static struct scoop_pcmcia_dev spitz_pcmcia_scoop[] = { static struct scoop_pcmcia_config spitz_pcmcia_config = { .devs = &spitz_pcmcia_scoop[0], .num_devs = 2, - .pcmcia_init = spitz_pcmcia_init, .power_ctrl = spitz_pcmcia_pwr, }; EXPORT_SYMBOL(spitzscoop_device); EXPORT_SYMBOL(spitzscoop2_device); - /* - * Spitz SSP Device - * - * Set the parent as the scoop device because a lot of SSP devices - * also use scoop functions and this makes the power up/down order - * work correctly. + * Spitz Keyboard Device */ -struct platform_device spitzssp_device = { - .name = "corgi-ssp", - .dev = { - .parent = &spitzscoop_device.dev, - }, +static struct platform_device spitzkbd_device = { + .name = "spitz-keyboard", .id = -1, }; -struct corgissp_machinfo spitz_ssp_machinfo = { - .port = 2, - .cs_lcdcon = SPITZ_GPIO_LCDCON_CS, - .cs_ads7846 = SPITZ_GPIO_ADS7846_CS, - .cs_max1111 = SPITZ_GPIO_MAX1111_CS, - .clk_lcdcon = 520, - .clk_ads7846 = 14, - .clk_max1111 = 56, -}; - /* - * Spitz Backlight Device + * Spitz LEDs */ -static void spitz_bl_kick_battery(void) -{ - void (*kick_batt)(void); - - kick_batt = symbol_get(sharpsl_battery_kick); - if (kick_batt) { - kick_batt(); - symbol_put(sharpsl_battery_kick); - } -} - -static struct generic_bl_info spitz_bl_machinfo = { - .name = "corgi-bl", - .default_intensity = 0x1f, - .limit_mask = 0x0b, - .max_intensity = 0x2f, - .kick_battery = spitz_bl_kick_battery, -}; - -static struct platform_device spitzbl_device = { - .name = "generic-bl", - .dev = { - .platform_data = &spitz_bl_machinfo, +static struct gpio_led spitz_gpio_leds[] = { + { + .name = "spitz:amber:charge", + .default_trigger = "sharpsl-charge", + .gpio = SPITZ_GPIO_LED_ORANGE, + }, + { + .name = "spitz:green:hddactivity", + .default_trigger = "ide-disk", + .gpio = SPITZ_GPIO_LED_GREEN, }, - .id = -1, }; - -/* - * Spitz Keyboard Device - */ -static struct platform_device spitzkbd_device = { - .name = "spitz-keyboard", - .id = -1, +static struct gpio_led_platform_data spitz_gpio_leds_info = { + .leds = spitz_gpio_leds, + .num_leds = ARRAY_SIZE(spitz_gpio_leds), }; - -/* - * Spitz LEDs - */ static struct platform_device spitzled_device = { - .name = "spitz-led", + .name = "leds-gpio", .id = -1, + .dev = { + .platform_data = &spitz_gpio_leds_info, + }, }; -/* - * Spitz Touch Screen Device - */ +#if defined(CONFIG_SPI_PXA2XX) || defined(CONFIG_SPI_PXA2XX_MODULE) +static struct pxa2xx_spi_master spitz_spi_info = { + .num_chipselect = 3, +}; -static unsigned long (*get_hsync_invperiod)(struct device *dev); +static struct ads7846_platform_data spitz_ads7846_info = { + .model = 7846, + .vref_delay_usecs = 100, + .x_plate_ohms = 419, + .y_plate_ohms = 486, + .gpio_pendown = SPITZ_GPIO_TP_INT, +}; -static void inline sharpsl_wait_sync(int gpio) +static void spitz_ads7846_cs(u32 command) { - while((GPLR(gpio) & GPIO_bit(gpio)) == 0); - while((GPLR(gpio) & GPIO_bit(gpio)) != 0); + gpio_set_value(SPITZ_GPIO_ADS7846_CS, !(command == PXA2XX_CS_ASSERT)); } -static struct device *spitz_pxafb_dev; +static struct pxa2xx_spi_chip spitz_ads7846_chip = { + .cs_control = spitz_ads7846_cs, +}; -static int is_pxafb_device(struct device * dev, void * data) +static void spitz_bl_kick_battery(void) { - struct platform_device *pdev = container_of(dev, struct platform_device, dev); - - return (strncmp(pdev->name, "pxa2xx-fb", 9) == 0); -} + void (*kick_batt)(void); -static unsigned long spitz_get_hsync_invperiod(void) -{ -#ifdef CONFIG_FB_PXA - if (!spitz_pxafb_dev) { - spitz_pxafb_dev = bus_find_device(&platform_bus_type, NULL, NULL, is_pxafb_device); - if (!spitz_pxafb_dev) - return 0; + kick_batt = symbol_get(sharpsl_battery_kick); + if (kick_batt) { + kick_batt(); + symbol_put(sharpsl_battery_kick); } - if (!get_hsync_invperiod) - get_hsync_invperiod = symbol_get(pxafb_get_hsync_time); - if (!get_hsync_invperiod) -#endif - return 0; - - return get_hsync_invperiod(spitz_pxafb_dev); } -static void spitz_put_hsync(void) -{ - put_device(spitz_pxafb_dev); - if (get_hsync_invperiod) - symbol_put(pxafb_get_hsync_time); - spitz_pxafb_dev = NULL; - get_hsync_invperiod = NULL; -} +static struct corgi_lcd_platform_data spitz_lcdcon_info = { + .init_mode = CORGI_LCD_MODE_VGA, + .max_intensity = 0x2f, + .default_intensity = 0x1f, + .limit_mask = 0x0b, + .gpio_backlight_cont = SPITZ_GPIO_BACKLIGHT_CONT, + .gpio_backlight_on = SPITZ_GPIO_BACKLIGHT_ON, + .kick_battery = spitz_bl_kick_battery, +}; -static void spitz_wait_hsync(void) +static void spitz_lcdcon_cs(u32 command) { - sharpsl_wait_sync(SPITZ_GPIO_HSYNC); + gpio_set_value(SPITZ_GPIO_LCDCON_CS, !(command == PXA2XX_CS_ASSERT)); } -static struct resource spitzts_resources[] = { - [0] = { - .start = SPITZ_IRQ_GPIO_TP_INT, - .end = SPITZ_IRQ_GPIO_TP_INT, - .flags = IORESOURCE_IRQ, - }, +static struct pxa2xx_spi_chip spitz_lcdcon_chip = { + .cs_control = spitz_lcdcon_cs, }; -static struct corgits_machinfo spitz_ts_machinfo = { - .get_hsync_invperiod = spitz_get_hsync_invperiod, - .put_hsync = spitz_put_hsync, - .wait_hsync = spitz_wait_hsync, +static void spitz_max1111_cs(u32 command) +{ + gpio_set_value(SPITZ_GPIO_MAX1111_CS, !(command == PXA2XX_CS_ASSERT)); +} + +static struct pxa2xx_spi_chip spitz_max1111_chip = { + .cs_control = spitz_max1111_cs, }; -static struct platform_device spitzts_device = { - .name = "corgi-ts", - .dev = { - .parent = &spitzssp_device.dev, - .platform_data = &spitz_ts_machinfo, +static struct spi_board_info spitz_spi_devices[] = { + { + .modalias = "ads7846", + .max_speed_hz = 1200000, + .bus_num = 2, + .chip_select = 0, + .platform_data = &spitz_ads7846_info, + .controller_data= &spitz_ads7846_chip, + .irq = gpio_to_irq(SPITZ_GPIO_TP_INT), + }, { + .modalias = "corgi-lcd", + .max_speed_hz = 50000, + .bus_num = 2, + .chip_select = 1, + .platform_data = &spitz_lcdcon_info, + .controller_data= &spitz_lcdcon_chip, + }, { + .modalias = "max1111", + .max_speed_hz = 450000, + .bus_num = 2, + .chip_select = 2, + .controller_data= &spitz_max1111_chip, }, - .id = -1, - .num_resources = ARRAY_SIZE(spitzts_resources), - .resource = spitzts_resources, }; +static void __init spitz_init_spi(void) +{ + int err; + + err = gpio_request(SPITZ_GPIO_ADS7846_CS, "ADS7846_CS"); + if (err) + return; + + err = gpio_request(SPITZ_GPIO_LCDCON_CS, "LCDCON_CS"); + if (err) + goto err_free_1; + + err = gpio_request(SPITZ_GPIO_MAX1111_CS, "MAX1111_CS"); + if (err) + goto err_free_2; + + if (machine_is_akita()) { + spitz_lcdcon_info.gpio_backlight_cont = AKITA_GPIO_BACKLIGHT_CONT; + spitz_lcdcon_info.gpio_backlight_on = AKITA_GPIO_BACKLIGHT_ON; + } + + pxa2xx_set_spi_info(2, &spitz_spi_info); + spi_register_board_info(ARRAY_AND_SIZE(spitz_spi_devices)); + return; + +err_free_2: + gpio_free(SPITZ_GPIO_LCDCON_CS); +err_free_1: + gpio_free(SPITZ_GPIO_ADS7846_CS); +} +#else +static inline void spitz_init_spi(void) {} +#endif /* * MMC/SD Device @@ -361,24 +416,35 @@ static int spitz_mci_init(struct device *dev, irq_handler_t spitz_detect_int, vo { int err; - /* setup GPIO for PXA27x MMC controller */ - pxa_gpio_mode(GPIO32_MMCCLK_MD); - pxa_gpio_mode(GPIO112_MMCCMD_MD); - pxa_gpio_mode(GPIO92_MMCDAT0_MD); - pxa_gpio_mode(GPIO109_MMCDAT1_MD); - pxa_gpio_mode(GPIO110_MMCDAT2_MD); - pxa_gpio_mode(GPIO111_MMCDAT3_MD); - pxa_gpio_mode(SPITZ_GPIO_nSD_DETECT | GPIO_IN); - pxa_gpio_mode(SPITZ_GPIO_nSD_WP | GPIO_IN); + err = gpio_request(SPITZ_GPIO_nSD_DETECT, "nSD_DETECT"); + if (err) + goto err_out; + + err = gpio_request(SPITZ_GPIO_nSD_WP, "nSD_WP"); + if (err) + goto err_free_1; + + gpio_direction_input(SPITZ_GPIO_nSD_DETECT); + gpio_direction_input(SPITZ_GPIO_nSD_WP); spitz_mci_platform_data.detect_delay = msecs_to_jiffies(250); err = request_irq(SPITZ_IRQ_GPIO_nSD_DETECT, spitz_detect_int, - IRQF_DISABLED | IRQF_TRIGGER_RISING | IRQF_TRIGGER_FALLING, + IRQF_DISABLED | IRQF_TRIGGER_RISING | + IRQF_TRIGGER_FALLING, "MMC card detect", data); - if (err) - printk(KERN_ERR "spitz_mci_init: MMC/SD: can't request MMC card detect IRQ\n"); + if (err) { + pr_err("%s: MMC/SD: can't request MMC card detect IRQ\n", + __func__); + goto err_free_2; + } + return 0; +err_free_2: + gpio_free(SPITZ_GPIO_nSD_WP); +err_free_1: + gpio_free(SPITZ_GPIO_nSD_DETECT); +err_out: return err; } @@ -394,12 +460,14 @@ static void spitz_mci_setpower(struct device *dev, unsigned int vdd) static int spitz_mci_get_ro(struct device *dev) { - return GPLR(SPITZ_GPIO_nSD_WP) & GPIO_bit(SPITZ_GPIO_nSD_WP); + return gpio_get_value(SPITZ_GPIO_nSD_WP); } static void spitz_mci_exit(struct device *dev, void *data) { free_irq(SPITZ_IRQ_GPIO_nSD_DETECT, data); + gpio_free(SPITZ_GPIO_nSD_WP); + gpio_free(SPITZ_GPIO_nSD_DETECT); } static struct pxamci_platform_data spitz_mci_platform_data = { @@ -416,27 +484,24 @@ static struct pxamci_platform_data spitz_mci_platform_data = { */ static int spitz_ohci_init(struct device *dev) { - /* Only Port 2 is connected */ - pxa_gpio_mode(SPITZ_GPIO_USB_CONNECT | GPIO_IN); - pxa_gpio_mode(SPITZ_GPIO_USB_HOST | GPIO_OUT); - pxa_gpio_mode(SPITZ_GPIO_USB_DEVICE | GPIO_IN); - - /* Setup USB Port 2 Output Control Register */ - UP2OCR = UP2OCR_HXS | UP2OCR_HXOE | UP2OCR_DPPDE | UP2OCR_DMPDE; - - GPSR(SPITZ_GPIO_USB_HOST) = GPIO_bit(SPITZ_GPIO_USB_HOST); + int err; - UHCHR = (UHCHR) & - ~(UHCHR_SSEP1 | UHCHR_SSEP2 | UHCHR_SSEP3 | UHCHR_SSE); + err = gpio_request(SPITZ_GPIO_USB_HOST, "USB_HOST"); + if (err) + return err; - UHCRHDA |= UHCRHDA_NOCP; + /* Only Port 2 is connected + * Setup USB Port 2 Output Control Register + */ + UP2OCR = UP2OCR_HXS | UP2OCR_HXOE | UP2OCR_DPPDE | UP2OCR_DMPDE; - return 0; + return gpio_direction_output(SPITZ_GPIO_USB_HOST, 1); } static struct pxaohci_platform_data spitz_ohci_platform_data = { .port_mode = PMM_NPS_MODE, .init = spitz_ohci_init, + .flags = ENABLE_PORT_ALL | NO_OC_PROTECTION, .power_budget = 150, }; @@ -444,27 +509,50 @@ static struct pxaohci_platform_data spitz_ohci_platform_data = { /* * Irda */ +static int spitz_irda_startup(struct device *dev) +{ + int rc; + + rc = gpio_request(SPITZ_GPIO_IR_ON, "IrDA on"); + if (rc) + goto err; + + rc = gpio_direction_output(SPITZ_GPIO_IR_ON, 1); + if (rc) + goto err_dir; + + return 0; + +err_dir: + gpio_free(SPITZ_GPIO_IR_ON); +err: + return rc; +} + +static void spitz_irda_shutdown(struct device *dev) +{ + gpio_free(SPITZ_GPIO_IR_ON); +} + static void spitz_irda_transceiver_mode(struct device *dev, int mode) { - if (mode & IR_OFF) - set_scoop_gpio(&spitzscoop2_device.dev, SPITZ_SCP2_IR_ON); - else - reset_scoop_gpio(&spitzscoop2_device.dev, SPITZ_SCP2_IR_ON); + gpio_set_value(SPITZ_GPIO_IR_ON, mode & IR_OFF); + pxa2xx_transceiver_mode(dev, mode); } #ifdef CONFIG_MACH_AKITA static void akita_irda_transceiver_mode(struct device *dev, int mode) { - if (mode & IR_OFF) - akita_set_ioexp(&akitaioexp_device.dev, AKITA_IOEXP_IR_ON); - else - akita_reset_ioexp(&akitaioexp_device.dev, AKITA_IOEXP_IR_ON); + gpio_set_value(AKITA_GPIO_IR_ON, mode & IR_OFF); + pxa2xx_transceiver_mode(dev, mode); } #endif static struct pxaficp_platform_data spitz_ficp_platform_data = { - .transceiver_cap = IR_SIRMODE | IR_OFF, - .transceiver_mode = spitz_irda_transceiver_mode, + .transceiver_cap = IR_SIRMODE | IR_OFF, + .transceiver_mode = spitz_irda_transceiver_mode, + .startup = spitz_irda_startup, + .shutdown = spitz_irda_shutdown, }; @@ -472,14 +560,6 @@ static struct pxaficp_platform_data spitz_ficp_platform_data = { * Spitz PXA Framebuffer */ -static void spitz_lcd_power(int on, struct fb_var_screeninfo *var) -{ - if (on) - corgi_lcdtg_hw_init(var->xres); - else - corgi_lcdtg_suspend(); -} - static struct pxafb_mode_info spitz_pxafb_modes[] = { { .pixclock = 19231, @@ -512,28 +592,19 @@ static struct pxafb_mach_info spitz_pxafb_info = { .modes = &spitz_pxafb_modes[0], .num_modes = 2, .fixed_modes = 1, - .lccr0 = LCCR0_Color | LCCR0_Sngl | LCCR0_Act | LCCR0_LDDALT | LCCR0_OUC | LCCR0_CMDIM | LCCR0_RDSTM, - .lccr3 = LCCR3_PixRsEdg | LCCR3_OutEnH, - .pxafb_lcd_power = spitz_lcd_power, + .lcd_conn = LCD_COLOR_TFT_16BPP | LCD_ALTERNATE_MAPPING, }; static struct platform_device *devices[] __initdata = { &spitzscoop_device, - &spitzssp_device, &spitzkbd_device, - &spitzts_device, - &spitzbl_device, &spitzled_device, }; static void spitz_poweroff(void) { - pxa_gpio_mode(SPITZ_GPIO_ON_RESET | GPIO_OUT); - GPSR(SPITZ_GPIO_ON_RESET) = GPIO_bit(SPITZ_GPIO_ON_RESET); - - mdelay(1000); - arm_machine_restart('h'); + arm_machine_restart('g'); } static void spitz_restart(char mode) @@ -547,61 +618,32 @@ static void spitz_restart(char mode) static void __init common_init(void) { + init_gpio_reset(SPITZ_GPIO_ON_RESET, 1); pm_power_off = spitz_poweroff; arm_pm_restart = spitz_restart; PMCR = 0x00; - /* setup sleep mode values */ - PWER = 0x00000002; - PFER = 0x00000000; - PRER = 0x00000002; - PGSR0 = 0x0158C000; - PGSR1 = 0x00FF0080; - PGSR2 = 0x0001C004; - /* Stop 3.6MHz and drive HIGH to PCMCIA and CS */ PCFR |= PCFR_OPDE; - corgi_ssp_set_machinfo(&spitz_ssp_machinfo); + pxa2xx_mfp_config(ARRAY_AND_SIZE(spitz_pin_config)); - pxa_gpio_mode(SPITZ_GPIO_HSYNC | GPIO_IN); + spitz_init_spi(); platform_add_devices(devices, ARRAY_SIZE(devices)); pxa_set_mci_info(&spitz_mci_platform_data); pxa_set_ohci_info(&spitz_ohci_platform_data); pxa_set_ficp_info(&spitz_ficp_platform_data); - set_pxa_fb_parent(&spitzssp_device.dev); set_pxa_fb_info(&spitz_pxafb_info); + pxa_set_i2c_info(NULL); } #if defined(CONFIG_MACH_SPITZ) || defined(CONFIG_MACH_BORZOI) -static void spitz_bl_set_intensity(int intensity) -{ - if (intensity > 0x10) - intensity += 0x10; - - /* Bits 0-4 are accessed via the SSP interface */ - corgi_ssp_blduty_set(intensity & 0x1f); - - /* Bit 5 is via SCOOP */ - if (intensity & 0x0020) - reset_scoop_gpio(&spitzscoop2_device.dev, SPITZ_SCP2_BACKLIGHT_CONT); - else - set_scoop_gpio(&spitzscoop2_device.dev, SPITZ_SCP2_BACKLIGHT_CONT); - - if (intensity) - set_scoop_gpio(&spitzscoop2_device.dev, SPITZ_SCP2_BACKLIGHT_ON); - else - reset_scoop_gpio(&spitzscoop2_device.dev, SPITZ_SCP2_BACKLIGHT_ON); -} - static void __init spitz_init(void) { platform_scoop_config = &spitz_pcmcia_config; - spitz_bl_machinfo.set_bl_intensity = spitz_bl_set_intensity; - common_init(); platform_device_register(&spitzscoop2_device); @@ -612,32 +654,17 @@ static void __init spitz_init(void) /* * Akita IO Expander */ -struct platform_device akitaioexp_device = { - .name = "akita-ioexp", - .id = -1, +static struct pca953x_platform_data akita_ioexp = { + .gpio_base = AKITA_IOEXP_GPIO_BASE, }; -EXPORT_SYMBOL_GPL(akitaioexp_device); - -static void akita_bl_set_intensity(int intensity) -{ - if (intensity > 0x10) - intensity += 0x10; - - /* Bits 0-4 are accessed via the SSP interface */ - corgi_ssp_blduty_set(intensity & 0x1f); - - /* Bit 5 is via IO-Expander */ - if (intensity & 0x0020) - akita_reset_ioexp(&akitaioexp_device.dev, AKITA_IOEXP_BACKLIGHT_CONT); - else - akita_set_ioexp(&akitaioexp_device.dev, AKITA_IOEXP_BACKLIGHT_CONT); - - if (intensity) - akita_set_ioexp(&akitaioexp_device.dev, AKITA_IOEXP_BACKLIGHT_ON); - else - akita_reset_ioexp(&akitaioexp_device.dev, AKITA_IOEXP_BACKLIGHT_ON); -} +static struct i2c_board_info akita_i2c_board_info[] = { + { + .type = "max7310", + .addr = 0x18, + .platform_data = &akita_ioexp, + }, +}; static void __init akita_init(void) { @@ -646,11 +673,10 @@ static void __init akita_init(void) /* We just pretend the second element of the array doesn't exist */ spitz_pcmcia_config.num_devs = 1; platform_scoop_config = &spitz_pcmcia_config; - spitz_bl_machinfo.set_bl_intensity = akita_bl_set_intensity; - platform_device_register(&akitaioexp_device); + pxa_set_i2c_info(NULL); + i2c_register_board_info(0, ARRAY_AND_SIZE(akita_i2c_board_info)); - spitzscoop_device.dev.parent = &akitaioexp_device.dev; common_init(); } #endif diff --git a/arch/arm/mach-pxa/spitz_pm.c b/arch/arm/mach-pxa/spitz_pm.c index 23f050feb20..53018db106a 100644 --- a/arch/arm/mach-pxa/spitz_pm.c +++ b/arch/arm/mach-pxa/spitz_pm.c @@ -20,13 +20,13 @@ #include <asm/irq.h> #include <asm/mach-types.h> -#include <asm/hardware.h> -#include <asm/hardware/scoop.h> +#include <mach/hardware.h> -#include <asm/arch/sharpsl.h> -#include <asm/arch/spitz.h> -#include <asm/arch/pxa-regs.h> -#include <asm/arch/pxa2xx-gpio.h> +#include <mach/sharpsl.h> +#include <mach/spitz.h> +#include <mach/pxa-regs.h> +#include <mach/pxa2xx-regs.h> +#include <mach/pxa2xx-gpio.h> #include "sharpsl.h" #define SHARPSL_CHARGE_ON_VOLT 0x99 /* 2.9V */ @@ -47,44 +47,35 @@ static void spitz_charger_init(void) static void spitz_measure_temp(int on) { - if (on) - set_scoop_gpio(&spitzscoop_device.dev, SPITZ_SCP_ADC_TEMP_ON); - else - reset_scoop_gpio(&spitzscoop_device.dev, SPITZ_SCP_ADC_TEMP_ON); + gpio_set_value(SPITZ_GPIO_ADC_TEMP_ON, on); } static void spitz_charge(int on) { if (on) { if (sharpsl_pm.flags & SHARPSL_SUSPENDED) { - set_scoop_gpio(&spitzscoop_device.dev, SPITZ_SCP_JK_B); - reset_scoop_gpio(&spitzscoop_device.dev, SPITZ_SCP_CHRG_ON); + gpio_set_value(SPITZ_GPIO_JK_B, 1); + gpio_set_value(SPITZ_GPIO_CHRG_ON, 0); } else { - reset_scoop_gpio(&spitzscoop_device.dev, SPITZ_SCP_JK_B); - reset_scoop_gpio(&spitzscoop_device.dev, SPITZ_SCP_CHRG_ON); + gpio_set_value(SPITZ_GPIO_JK_B, 0); + gpio_set_value(SPITZ_GPIO_CHRG_ON, 0); } } else { - reset_scoop_gpio(&spitzscoop_device.dev, SPITZ_SCP_JK_B); - set_scoop_gpio(&spitzscoop_device.dev, SPITZ_SCP_CHRG_ON); + gpio_set_value(SPITZ_GPIO_JK_B, 0); + gpio_set_value(SPITZ_GPIO_CHRG_ON, 1); } } static void spitz_discharge(int on) { - if (on) - set_scoop_gpio(&spitzscoop_device.dev, SPITZ_SCP_JK_A); - else - reset_scoop_gpio(&spitzscoop_device.dev, SPITZ_SCP_JK_A); + gpio_set_value(SPITZ_GPIO_JK_A, on); } /* HACK - For unknown reasons, accurate voltage readings are only made with a load on the power bus which the green led on spitz provides */ static void spitz_discharge1(int on) { - if (on) - set_scoop_gpio(&spitzscoop_device.dev, SPITZ_SCP_LED_GREEN); - else - reset_scoop_gpio(&spitzscoop_device.dev, SPITZ_SCP_LED_GREEN); + gpio_set_value(SPITZ_GPIO_LED_GREEN, on); } static void spitz_presuspend(void) @@ -207,7 +198,9 @@ struct sharpsl_charger_machinfo spitz_pm_machinfo = { .read_devdata = spitzpm_read_devdata, .charger_wakeup = spitz_charger_wakeup, .should_wakeup = spitz_should_wakeup, +#ifdef CONFIG_BACKLIGHT_CORGI .backlight_limit = corgibl_limit_intensity, +#endif .charge_on_volt = SHARPSL_CHARGE_ON_VOLT, .charge_on_temp = SHARPSL_CHARGE_ON_TEMP, .charge_acin_high = SHARPSL_CHARGE_ON_ACIN_HIGH, @@ -229,6 +222,10 @@ static int __devinit spitzpm_init(void) { int ret; + if (!machine_is_spitz() && !machine_is_akita() + && !machine_is_borzoi()) + return -ENODEV; + spitzpm_device = platform_device_alloc("sharpsl-pm", -1); if (!spitzpm_device) return -ENOMEM; diff --git a/arch/arm/mach-pxa/ssp.c b/arch/arm/mach-pxa/ssp.c index 0bb31982fb6..2c31ec72568 100644 --- a/arch/arm/mach-pxa/ssp.c +++ b/arch/arm/mach-pxa/ssp.c @@ -14,13 +14,6 @@ * IO-based SSP applications and allows easy port setup for DMA access. * * Author: Liam Girdwood <liam.girdwood@wolfsonmicro.com> - * - * Revision history: - * 22nd Aug 2003 Initial version. - * 20th Dec 2004 Added ssp_config for changing port config without - * closing the port. - * 4th Aug 2005 Added option to disable irq handler registration and - * cleaned up irq and clock detection. */ #include <linux/module.h> @@ -35,13 +28,13 @@ #include <linux/clk.h> #include <linux/err.h> #include <linux/platform_device.h> +#include <linux/io.h> -#include <asm/io.h> #include <asm/irq.h> -#include <asm/hardware.h> -#include <asm/arch/ssp.h> -#include <asm/arch/pxa-regs.h> -#include <asm/arch/regs-ssp.h> +#include <mach/hardware.h> +#include <mach/ssp.h> +#include <mach/pxa-regs.h> +#include <mach/regs-ssp.h> #define TIMEOUT 100000 @@ -285,7 +278,7 @@ int ssp_init(struct ssp_dev *dev, u32 port, u32 init_flags) goto out_region; dev->irq = ssp->irq; } else - dev->irq = 0; + dev->irq = NO_IRQ; /* turn on SSP port clock */ clk_enable(ssp->clk); @@ -306,7 +299,8 @@ void ssp_exit(struct ssp_dev *dev) struct ssp_device *ssp = dev->ssp; ssp_disable(dev); - free_irq(dev->irq, dev); + if (dev->irq != NO_IRQ) + free_irq(dev->irq, dev); clk_disable(ssp->clk); ssp_free(ssp); } @@ -360,6 +354,7 @@ static int __devinit ssp_probe(struct platform_device *pdev, int type) dev_err(&pdev->dev, "failed to allocate memory"); return -ENOMEM; } + ssp->pdev = pdev; ssp->clk = clk_get(&pdev->dev, "SSPCLK"); if (IS_ERR(ssp->clk)) { diff --git a/arch/arm/mach-pxa/standby.S b/arch/arm/mach-pxa/standby.S index 167412e6bec..f3821cfda72 100644 --- a/arch/arm/mach-pxa/standby.S +++ b/arch/arm/mach-pxa/standby.S @@ -11,9 +11,10 @@ #include <linux/linkage.h> #include <asm/assembler.h> -#include <asm/hardware.h> +#include <mach/hardware.h> -#include <asm/arch/pxa-regs.h> +#include <mach/pxa-regs.h> +#include <mach/pxa2xx-regs.h> .text @@ -35,20 +36,20 @@ ENTRY(pxa_cpu_standby) #ifdef CONFIG_PXA3xx -#define MDCNFG 0x0000 -#define MDCNFG_DMCEN (1 << 30) -#define DDR_HCAL 0x0060 -#define DDR_HCAL_HCRNG 0x1f -#define DDR_HCAL_HCPROG (1 << 28) -#define DDR_HCAL_HCEN (1 << 31) -#define DMCIER 0x0070 -#define DMCIER_EDLP (1 << 29) -#define DMCISR 0x0078 -#define RCOMP 0x0100 -#define RCOMP_SWEVAL (1 << 31) +#define PXA3_MDCNFG 0x0000 +#define PXA3_MDCNFG_DMCEN (1 << 30) +#define PXA3_DDR_HCAL 0x0060 +#define PXA3_DDR_HCAL_HCRNG 0x1f +#define PXA3_DDR_HCAL_HCPROG (1 << 28) +#define PXA3_DDR_HCAL_HCEN (1 << 31) +#define PXA3_DMCIER 0x0070 +#define PXA3_DMCIER_EDLP (1 << 29) +#define PXA3_DMCISR 0x0078 +#define PXA3_RCOMP 0x0100 +#define PXA3_RCOMP_SWEVAL (1 << 31) ENTRY(pm_enter_standby_start) - mov r1, #0xf6000000 @ DMEMC_REG_BASE (MDCNFG) + mov r1, #0xf6000000 @ DMEMC_REG_BASE (PXA3_MDCNFG) add r1, r1, #0x00100000 /* @@ -59,54 +60,54 @@ ENTRY(pm_enter_standby_start) * This also means that only the dynamic memory controller * can be reliably accessed in the code following standby. */ - ldr r2, [r1] @ Dummy read MDCNFG + ldr r2, [r1] @ Dummy read PXA3_MDCNFG mcr p14, 0, r0, c7, c0, 0 .rept 8 nop .endr - ldr r0, [r1, #DDR_HCAL] @ Clear (and wait for) HCEN - bic r0, r0, #DDR_HCAL_HCEN - str r0, [r1, #DDR_HCAL] -1: ldr r0, [r1, #DDR_HCAL] - tst r0, #DDR_HCAL_HCEN + ldr r0, [r1, #PXA3_DDR_HCAL] @ Clear (and wait for) HCEN + bic r0, r0, #PXA3_DDR_HCAL_HCEN + str r0, [r1, #PXA3_DDR_HCAL] +1: ldr r0, [r1, #PXA3_DDR_HCAL] + tst r0, #PXA3_DDR_HCAL_HCEN bne 1b - ldr r0, [r1, #RCOMP] @ Initiate RCOMP - orr r0, r0, #RCOMP_SWEVAL - str r0, [r1, #RCOMP] + ldr r0, [r1, #PXA3_RCOMP] @ Initiate RCOMP + orr r0, r0, #PXA3_RCOMP_SWEVAL + str r0, [r1, #PXA3_RCOMP] - mov r0, #~0 @ Clear interrupts - str r0, [r1, #DMCISR] + mov r0, #~0 @ Clear interrupts + str r0, [r1, #PXA3_DMCISR] - ldr r0, [r1, #DMCIER] @ set DMIER[EDLP] - orr r0, r0, #DMCIER_EDLP - str r0, [r1, #DMCIER] + ldr r0, [r1, #PXA3_DMCIER] @ set DMIER[EDLP] + orr r0, r0, #PXA3_DMCIER_EDLP + str r0, [r1, #PXA3_DMCIER] - ldr r0, [r1, #DDR_HCAL] @ clear HCRNG, set HCPROG, HCEN - bic r0, r0, #DDR_HCAL_HCRNG - orr r0, r0, #DDR_HCAL_HCEN | DDR_HCAL_HCPROG - str r0, [r1, #DDR_HCAL] + ldr r0, [r1, #PXA3_DDR_HCAL] @ clear HCRNG, set HCPROG, HCEN + bic r0, r0, #PXA3_DDR_HCAL_HCRNG + orr r0, r0, #PXA3_DDR_HCAL_HCEN | PXA3_DDR_HCAL_HCPROG + str r0, [r1, #PXA3_DDR_HCAL] -1: ldr r0, [r1, #DMCISR] - tst r0, #DMCIER_EDLP +1: ldr r0, [r1, #PXA3_DMCISR] + tst r0, #PXA3_DMCIER_EDLP beq 1b - ldr r0, [r1, #MDCNFG] @ set MDCNFG[DMCEN] - orr r0, r0, #MDCNFG_DMCEN - str r0, [r1, #MDCNFG] -1: ldr r0, [r1, #MDCNFG] - tst r0, #MDCNFG_DMCEN + ldr r0, [r1, #PXA3_MDCNFG] @ set PXA3_MDCNFG[DMCEN] + orr r0, r0, #PXA3_MDCNFG_DMCEN + str r0, [r1, #PXA3_MDCNFG] +1: ldr r0, [r1, #PXA3_MDCNFG] + tst r0, #PXA3_MDCNFG_DMCEN beq 1b - ldr r0, [r1, #DDR_HCAL] @ set DDR_HCAL[HCRNG] + ldr r0, [r1, #PXA3_DDR_HCAL] @ set PXA3_DDR_HCAL[HCRNG] orr r0, r0, #2 @ HCRNG - str r0, [r1, #DDR_HCAL] + str r0, [r1, #PXA3_DDR_HCAL] - ldr r0, [r1, #DMCIER] @ Clear the interrupt + ldr r0, [r1, #PXA3_DMCIER] @ Clear the interrupt bic r0, r0, #0x20000000 - str r0, [r1, #DMCIER] + str r0, [r1, #PXA3_DMCIER] mov pc, lr ENTRY(pm_enter_standby_end) diff --git a/arch/arm/mach-pxa/tavorevb.c b/arch/arm/mach-pxa/tavorevb.c new file mode 100644 index 00000000000..589d32b4fc4 --- /dev/null +++ b/arch/arm/mach-pxa/tavorevb.c @@ -0,0 +1,84 @@ +/* + * linux/arch/arm/mach-pxa/tavorevb.c + * + * Support for the Marvell PXA930 Evaluation Board + * + * Copyright (C) 2007-2008 Marvell International Ltd. + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * publishhed by the Free Software Foundation. + */ + +#include <linux/module.h> +#include <linux/kernel.h> +#include <linux/interrupt.h> +#include <linux/init.h> +#include <linux/platform_device.h> +#include <linux/clk.h> +#include <linux/gpio.h> +#include <linux/smc91x.h> + +#include <asm/mach-types.h> +#include <asm/mach/arch.h> +#include <mach/hardware.h> +#include <mach/pxa3xx-regs.h> +#include <mach/mfp-pxa930.h> + +#include "devices.h" +#include "generic.h" + +/* Tavor EVB MFP configurations */ +static mfp_cfg_t tavorevb_mfp_cfg[] __initdata = { + /* Ethernet */ + DF_nCS1_nCS3, + GPIO47_GPIO, +}; + +#define TAVOREVB_ETH_PHYS (0x14000000) + +static struct resource smc91x_resources[] = { + [0] = { + .start = (TAVOREVB_ETH_PHYS + 0x300), + .end = (TAVOREVB_ETH_PHYS + 0xfffff), + .flags = IORESOURCE_MEM, + }, + [1] = { + .start = gpio_to_irq(mfp_to_gpio(MFP_PIN_GPIO47)), + .end = gpio_to_irq(mfp_to_gpio(MFP_PIN_GPIO47)), + .flags = IORESOURCE_IRQ | IORESOURCE_IRQ_HIGHEDGE, + } +}; + +static struct smc91x_platdata tavorevb_smc91x_info = { + .flags = SMC91X_USE_16BIT | SMC91X_NOWAIT | SMC91X_USE_DMA, +}; + +static struct platform_device smc91x_device = { + .name = "smc91x", + .id = 0, + .num_resources = ARRAY_SIZE(smc91x_resources), + .resource = smc91x_resources, + .dev = { + .platform_data = &tavorevb_smc91x_info, + }, +}; + +static void __init tavorevb_init(void) +{ + /* initialize MFP configurations */ + pxa3xx_mfp_config(ARRAY_AND_SIZE(tavorevb_mfp_cfg)); + + platform_device_register(&smc91x_device); +} + +MACHINE_START(TAVOREVB, "PXA930 Evaluation Board (aka TavorEVB)") + /* Maintainer: Eric Miao <eric.miao@marvell.com> */ + .phys_io = 0x40000000, + .boot_params = 0xa0000100, + .io_pg_offst = (io_p2v(0x40000000) >> 18) & 0xfffc, + .map_io = pxa_map_io, + .init_irq = pxa3xx_init_irq, + .timer = &pxa_timer, + .init_machine = tavorevb_init, +MACHINE_END diff --git a/arch/arm/mach-pxa/time.c b/arch/arm/mach-pxa/time.c index 7b7c0179795..f8a9a62959e 100644 --- a/arch/arm/mach-pxa/time.c +++ b/arch/arm/mach-pxa/time.c @@ -17,12 +17,12 @@ #include <linux/interrupt.h> #include <linux/clockchips.h> #include <linux/sched.h> +#include <linux/cnt32_to_63.h> #include <asm/div64.h> -#include <asm/cnt32_to_63.h> #include <asm/mach/irq.h> #include <asm/mach/time.h> -#include <asm/arch/pxa-regs.h> +#include <mach/pxa-regs.h> #include <asm/mach-types.h> /* @@ -155,7 +155,7 @@ static void __init pxa_timer_init(void) OIER = 0; OSSR = OSSR_M0 | OSSR_M1 | OSSR_M2 | OSSR_M3; - if (cpu_is_pxa21x() || cpu_is_pxa25x()) + if (cpu_is_pxa25x()) clock_tick_rate = 3686400; else if (machine_is_mainstone()) clock_tick_rate = 3249600; diff --git a/arch/arm/mach-pxa/tosa-bt.c b/arch/arm/mach-pxa/tosa-bt.c new file mode 100644 index 00000000000..fb0294bd431 --- /dev/null +++ b/arch/arm/mach-pxa/tosa-bt.c @@ -0,0 +1,150 @@ +/* + * Bluetooth built-in chip control + * + * Copyright (c) 2008 Dmitry Baryshkov + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + * + */ + +#include <linux/kernel.h> +#include <linux/module.h> +#include <linux/platform_device.h> +#include <linux/gpio.h> +#include <linux/delay.h> +#include <linux/rfkill.h> + +#include <mach/tosa_bt.h> + +static void tosa_bt_on(struct tosa_bt_data *data) +{ + gpio_set_value(data->gpio_reset, 0); + gpio_set_value(data->gpio_pwr, 1); + gpio_set_value(data->gpio_reset, 1); + mdelay(20); + gpio_set_value(data->gpio_reset, 0); +} + +static void tosa_bt_off(struct tosa_bt_data *data) +{ + gpio_set_value(data->gpio_reset, 1); + mdelay(10); + gpio_set_value(data->gpio_pwr, 0); + gpio_set_value(data->gpio_reset, 0); +} + +static int tosa_bt_toggle_radio(void *data, enum rfkill_state state) +{ + pr_info("BT_RADIO going: %s\n", + state == RFKILL_STATE_ON ? "on" : "off"); + + if (state == RFKILL_STATE_ON) { + pr_info("TOSA_BT: going ON\n"); + tosa_bt_on(data); + } else { + pr_info("TOSA_BT: going OFF\n"); + tosa_bt_off(data); + } + return 0; +} + +static int tosa_bt_probe(struct platform_device *dev) +{ + int rc; + struct rfkill *rfk; + + struct tosa_bt_data *data = dev->dev.platform_data; + + rc = gpio_request(data->gpio_reset, "Bluetooth reset"); + if (rc) + goto err_reset; + rc = gpio_direction_output(data->gpio_reset, 0); + if (rc) + goto err_reset_dir; + rc = gpio_request(data->gpio_pwr, "Bluetooth power"); + if (rc) + goto err_pwr; + rc = gpio_direction_output(data->gpio_pwr, 0); + if (rc) + goto err_pwr_dir; + + rfk = rfkill_allocate(&dev->dev, RFKILL_TYPE_BLUETOOTH); + if (!rfk) { + rc = -ENOMEM; + goto err_rfk_alloc; + } + + rfk->name = "tosa-bt"; + rfk->toggle_radio = tosa_bt_toggle_radio; + rfk->data = data; +#ifdef CONFIG_RFKILL_LEDS + rfk->led_trigger.name = "tosa-bt"; +#endif + + rc = rfkill_register(rfk); + if (rc) + goto err_rfkill; + + platform_set_drvdata(dev, rfk); + + return 0; + +err_rfkill: + if (rfk) + rfkill_free(rfk); + rfk = NULL; +err_rfk_alloc: + tosa_bt_off(data); +err_pwr_dir: + gpio_free(data->gpio_pwr); +err_pwr: +err_reset_dir: + gpio_free(data->gpio_reset); +err_reset: + return rc; +} + +static int __devexit tosa_bt_remove(struct platform_device *dev) +{ + struct tosa_bt_data *data = dev->dev.platform_data; + struct rfkill *rfk = platform_get_drvdata(dev); + + platform_set_drvdata(dev, NULL); + + if (rfk) + rfkill_unregister(rfk); + rfk = NULL; + + tosa_bt_off(data); + + gpio_free(data->gpio_pwr); + gpio_free(data->gpio_reset); + + return 0; +} + +static struct platform_driver tosa_bt_driver = { + .probe = tosa_bt_probe, + .remove = __devexit_p(tosa_bt_remove), + + .driver = { + .name = "tosa-bt", + .owner = THIS_MODULE, + }, +}; + + +static int __init tosa_bt_init(void) +{ + return platform_driver_register(&tosa_bt_driver); +} + +static void __exit tosa_bt_exit(void) +{ + platform_driver_unregister(&tosa_bt_driver); +} + +module_init(tosa_bt_init); +module_exit(tosa_bt_exit); diff --git a/arch/arm/mach-pxa/tosa.c b/arch/arm/mach-pxa/tosa.c index ab4a9f57991..130e37e4ebd 100644 --- a/arch/arm/mach-pxa/tosa.c +++ b/arch/arm/mach-pxa/tosa.c @@ -18,36 +18,39 @@ #include <linux/major.h> #include <linux/fs.h> #include <linux/interrupt.h> +#include <linux/delay.h> +#include <linux/fb.h> #include <linux/mmc/host.h> +#include <linux/mfd/tc6393xb.h> +#include <linux/mfd/tmio.h> +#include <linux/mtd/nand.h> +#include <linux/mtd/partitions.h> #include <linux/pm.h> -#include <linux/delay.h> #include <linux/gpio_keys.h> #include <linux/input.h> #include <linux/gpio.h> +#include <linux/pda_power.h> +#include <linux/rfkill.h> #include <asm/setup.h> -#include <asm/memory.h> #include <asm/mach-types.h> -#include <asm/hardware.h> -#include <asm/irq.h> -#include <asm/system.h> -#include <asm/arch/pxa-regs.h> -#include <asm/arch/pxa2xx-regs.h> -#include <asm/arch/mfp-pxa25x.h> -#include <asm/arch/irda.h> -#include <asm/arch/i2c.h> -#include <asm/arch/mmc.h> -#include <asm/arch/udc.h> +#include <mach/pxa2xx-regs.h> +#include <mach/mfp-pxa25x.h> +#include <mach/reset.h> +#include <mach/irda.h> +#include <mach/i2c.h> +#include <mach/mmc.h> +#include <mach/udc.h> +#include <mach/tosa_bt.h> #include <asm/mach/arch.h> -#include <asm/mach/map.h> -#include <asm/mach/irq.h> -#include <asm/arch/tosa.h> +#include <mach/tosa.h> #include <asm/hardware/scoop.h> #include <asm/mach/sharpsl_param.h> #include "generic.h" +#include "clock.h" #include "devices.h" static unsigned long tosa_pin_config[] = { @@ -86,7 +89,7 @@ static unsigned long tosa_pin_config[] = { GPIO6_MMC_CLK, GPIO8_MMC_CS0, GPIO9_GPIO, /* Detect */ - // GPIO10 nSD_INT + GPIO10_GPIO, /* nSD_INT */ /* CF */ GPIO13_GPIO, /* CD_IRQ */ @@ -124,34 +127,34 @@ static unsigned long tosa_pin_config[] = { GPIO44_BTUART_CTS, GPIO45_BTUART_RTS, - /* IrDA */ - GPIO46_STUART_RXD, - GPIO47_STUART_TXD, - /* Keybd */ - GPIO58_GPIO, - GPIO59_GPIO, - GPIO60_GPIO, - GPIO61_GPIO, - GPIO62_GPIO, - GPIO63_GPIO, - GPIO64_GPIO, - GPIO65_GPIO, - GPIO66_GPIO, - GPIO67_GPIO, - GPIO68_GPIO, - GPIO69_GPIO, - GPIO70_GPIO, - GPIO71_GPIO, - GPIO72_GPIO, - GPIO73_GPIO, - GPIO74_GPIO, - GPIO75_GPIO, + GPIO58_GPIO | MFP_LPM_DRIVE_LOW, + GPIO59_GPIO | MFP_LPM_DRIVE_LOW, + GPIO60_GPIO | MFP_LPM_DRIVE_LOW, + GPIO61_GPIO | MFP_LPM_DRIVE_LOW, + GPIO62_GPIO | MFP_LPM_DRIVE_LOW, + GPIO63_GPIO | MFP_LPM_DRIVE_LOW, + GPIO64_GPIO | MFP_LPM_DRIVE_LOW, + GPIO65_GPIO | MFP_LPM_DRIVE_LOW, + GPIO66_GPIO | MFP_LPM_DRIVE_LOW, + GPIO67_GPIO | MFP_LPM_DRIVE_LOW, + GPIO68_GPIO | MFP_LPM_DRIVE_LOW, + GPIO69_GPIO | MFP_LPM_DRIVE_LOW, + GPIO70_GPIO | MFP_LPM_DRIVE_LOW, + GPIO71_GPIO | MFP_LPM_DRIVE_LOW, + GPIO72_GPIO | MFP_LPM_DRIVE_LOW, + GPIO73_GPIO | MFP_LPM_DRIVE_LOW, + GPIO74_GPIO | MFP_LPM_DRIVE_LOW, + GPIO75_GPIO | MFP_LPM_DRIVE_LOW, /* SPI */ GPIO81_SSP2_CLK_OUT, GPIO82_SSP2_FRM_OUT, GPIO83_SSP2_TXD, + + /* IrDA is managed in other way */ + GPIO46_GPIO, + GPIO47_GPIO, }; /* @@ -249,6 +252,15 @@ static int tosa_mci_init(struct device *dev, irq_handler_t tosa_detect_int, void tosa_mci_platform_data.detect_delay = msecs_to_jiffies(250); + err = gpio_request(TOSA_GPIO_nSD_DETECT, "MMC/SD card detect"); + if (err) { + printk(KERN_ERR "tosa_mci_init: can't request nSD_DETECT gpio\n"); + goto err_gpio_detect; + } + err = gpio_direction_input(TOSA_GPIO_nSD_DETECT); + if (err) + goto err_gpio_detect_dir; + err = request_irq(TOSA_IRQ_GPIO_nSD_DETECT, tosa_detect_int, IRQF_DISABLED | IRQF_TRIGGER_RISING | IRQF_TRIGGER_FALLING, "MMC/SD card detect", data); @@ -257,7 +269,7 @@ static int tosa_mci_init(struct device *dev, irq_handler_t tosa_detect_int, void goto err_irq; } - err = gpio_request(TOSA_GPIO_SD_WP, "sd_wp"); + err = gpio_request(TOSA_GPIO_SD_WP, "SD Write Protect"); if (err) { printk(KERN_ERR "tosa_mci_init: can't request SD_WP gpio\n"); goto err_gpio_wp; @@ -266,7 +278,7 @@ static int tosa_mci_init(struct device *dev, irq_handler_t tosa_detect_int, void if (err) goto err_gpio_wp_dir; - err = gpio_request(TOSA_GPIO_PWR_ON, "sd_pwr"); + err = gpio_request(TOSA_GPIO_PWR_ON, "SD Power"); if (err) { printk(KERN_ERR "tosa_mci_init: can't request SD_PWR gpio\n"); goto err_gpio_pwr; @@ -275,8 +287,20 @@ static int tosa_mci_init(struct device *dev, irq_handler_t tosa_detect_int, void if (err) goto err_gpio_pwr_dir; + err = gpio_request(TOSA_GPIO_nSD_INT, "SD Int"); + if (err) { + printk(KERN_ERR "tosa_mci_init: can't request SD_PWR gpio\n"); + goto err_gpio_int; + } + err = gpio_direction_input(TOSA_GPIO_nSD_INT); + if (err) + goto err_gpio_int_dir; + return 0; +err_gpio_int_dir: + gpio_free(TOSA_GPIO_nSD_INT); +err_gpio_int: err_gpio_pwr_dir: gpio_free(TOSA_GPIO_PWR_ON); err_gpio_pwr: @@ -285,6 +309,9 @@ err_gpio_wp_dir: err_gpio_wp: free_irq(TOSA_IRQ_GPIO_nSD_DETECT, data); err_irq: +err_gpio_detect_dir: + gpio_free(TOSA_GPIO_nSD_DETECT); +err_gpio_detect: return err; } @@ -306,9 +333,11 @@ static int tosa_mci_get_ro(struct device *dev) static void tosa_mci_exit(struct device *dev, void *data) { + gpio_free(TOSA_GPIO_nSD_INT); gpio_free(TOSA_GPIO_PWR_ON); gpio_free(TOSA_GPIO_SD_WP); free_irq(TOSA_IRQ_GPIO_nSD_DETECT, data); + gpio_free(TOSA_GPIO_nSD_DETECT); } static struct pxamci_platform_data tosa_mci_platform_data = { @@ -322,29 +351,55 @@ static struct pxamci_platform_data tosa_mci_platform_data = { /* * Irda */ +static void tosa_irda_transceiver_mode(struct device *dev, int mode) +{ + if (mode & IR_OFF) { + gpio_set_value(TOSA_GPIO_IR_POWERDWN, 0); + pxa2xx_transceiver_mode(dev, mode); + gpio_direction_output(TOSA_GPIO_IRDA_TX, 0); + } else { + pxa2xx_transceiver_mode(dev, mode); + gpio_set_value(TOSA_GPIO_IR_POWERDWN, 1); + } +} + static int tosa_irda_startup(struct device *dev) { int ret; + ret = gpio_request(TOSA_GPIO_IRDA_TX, "IrDA TX"); + if (ret) + goto err_tx; + ret = gpio_direction_output(TOSA_GPIO_IRDA_TX, 0); + if (ret) + goto err_tx_dir; + ret = gpio_request(TOSA_GPIO_IR_POWERDWN, "IrDA powerdown"); if (ret) - return ret; + goto err_pwr; ret = gpio_direction_output(TOSA_GPIO_IR_POWERDWN, 0); if (ret) - gpio_free(TOSA_GPIO_IR_POWERDWN); + goto err_pwr_dir; - return ret; - } + tosa_irda_transceiver_mode(dev, IR_SIRMODE | IR_OFF); -static void tosa_irda_shutdown(struct device *dev) -{ + return 0; + +err_pwr_dir: gpio_free(TOSA_GPIO_IR_POWERDWN); +err_pwr: +err_tx_dir: + gpio_free(TOSA_GPIO_IRDA_TX); +err_tx: + return ret; } -static void tosa_irda_transceiver_mode(struct device *dev, int mode) +static void tosa_irda_shutdown(struct device *dev) { - gpio_set_value(TOSA_GPIO_IR_POWERDWN, !(mode & IR_OFF)); + tosa_irda_transceiver_mode(dev, IR_SIRMODE | IR_OFF); + gpio_free(TOSA_GPIO_IR_POWERDWN); + gpio_free(TOSA_GPIO_IRDA_TX); } static struct pxaficp_platform_data tosa_ficp_platform_data = { @@ -355,6 +410,70 @@ static struct pxaficp_platform_data tosa_ficp_platform_data = { }; /* + * Tosa AC IN + */ +static int tosa_power_init(struct device *dev) +{ + int ret = gpio_request(TOSA_GPIO_AC_IN, "ac in"); + if (ret) + goto err_gpio_req; + + ret = gpio_direction_input(TOSA_GPIO_AC_IN); + if (ret) + goto err_gpio_in; + + return 0; + +err_gpio_in: + gpio_free(TOSA_GPIO_AC_IN); +err_gpio_req: + return ret; +} + +static void tosa_power_exit(struct device *dev) +{ + gpio_free(TOSA_GPIO_AC_IN); +} + +static int tosa_power_ac_online(void) +{ + return gpio_get_value(TOSA_GPIO_AC_IN) == 0; +} + +static char *tosa_ac_supplied_to[] = { + "main-battery", + "backup-battery", + "jacket-battery", +}; + +static struct pda_power_pdata tosa_power_data = { + .init = tosa_power_init, + .is_ac_online = tosa_power_ac_online, + .exit = tosa_power_exit, + .supplied_to = tosa_ac_supplied_to, + .num_supplicants = ARRAY_SIZE(tosa_ac_supplied_to), +}; + +static struct resource tosa_power_resource[] = { + { + .name = "ac", + .start = gpio_to_irq(TOSA_GPIO_AC_IN), + .end = gpio_to_irq(TOSA_GPIO_AC_IN), + .flags = IORESOURCE_IRQ | + IORESOURCE_IRQ_HIGHEDGE | + IORESOURCE_IRQ_LOWEDGE, + }, +}; + +static struct platform_device tosa_power_device = { + .name = "pda-power", + .id = -1, + .dev.platform_data = &tosa_power_data, + .resource = tosa_power_resource, + .num_resources = ARRAY_SIZE(tosa_power_resource), +}; + +/* * Tosa Keyboard */ static struct platform_device tosakbd_device = { @@ -403,6 +522,14 @@ static struct gpio_keys_button tosa_gpio_keys[] = { .wakeup = 1, .active_low = 1, }, + { + .type = EV_SW, + .code = SW_HEADPHONE_INSERT, + .gpio = TOSA_GPIO_EAR_IN, + .desc = "HeadPhone insert", + .active_low = 1, + .debounce_interval = 300, + }, }; static struct gpio_keys_platform_data tosa_gpio_keys_platform_data = { @@ -439,7 +566,7 @@ static struct gpio_led tosa_gpio_leds[] = { }, { .name = "tosa:blue:bluetooth", - .default_trigger = "none", + .default_trigger = "tosa-bt", .gpio = TOSA_GPIO_BT_LED, }, }; @@ -457,21 +584,184 @@ static struct platform_device tosaled_device = { }, }; +/* + * Toshiba Mobile IO Controller + */ +static struct resource tc6393xb_resources[] = { + [0] = { + .start = TOSA_LCDC_PHYS, + .end = TOSA_LCDC_PHYS + 0x3ffffff, + .flags = IORESOURCE_MEM, + }, + + [1] = { + .start = TOSA_IRQ_GPIO_TC6393XB_INT, + .end = TOSA_IRQ_GPIO_TC6393XB_INT, + .flags = IORESOURCE_IRQ, + }, +}; + + +static int tosa_tc6393xb_enable(struct platform_device *dev) +{ + int rc; + + rc = gpio_request(TOSA_GPIO_TC6393XB_REST_IN, "tc6393xb #pclr"); + if (rc) + goto err_req_pclr; + rc = gpio_request(TOSA_GPIO_TC6393XB_SUSPEND, "tc6393xb #suspend"); + if (rc) + goto err_req_suspend; + rc = gpio_request(TOSA_GPIO_TC6393XB_L3V_ON, "l3v"); + if (rc) + goto err_req_l3v; + rc = gpio_direction_output(TOSA_GPIO_TC6393XB_L3V_ON, 0); + if (rc) + goto err_dir_l3v; + rc = gpio_direction_output(TOSA_GPIO_TC6393XB_SUSPEND, 0); + if (rc) + goto err_dir_suspend; + rc = gpio_direction_output(TOSA_GPIO_TC6393XB_REST_IN, 0); + if (rc) + goto err_dir_pclr; + + mdelay(1); + + gpio_set_value(TOSA_GPIO_TC6393XB_SUSPEND, 1); + + mdelay(10); + + gpio_set_value(TOSA_GPIO_TC6393XB_REST_IN, 1); + gpio_set_value(TOSA_GPIO_TC6393XB_L3V_ON, 1); + + return 0; +err_dir_pclr: +err_dir_suspend: +err_dir_l3v: + gpio_free(TOSA_GPIO_TC6393XB_L3V_ON); +err_req_l3v: + gpio_free(TOSA_GPIO_TC6393XB_SUSPEND); +err_req_suspend: + gpio_free(TOSA_GPIO_TC6393XB_REST_IN); +err_req_pclr: + return rc; +} + +static int tosa_tc6393xb_disable(struct platform_device *dev) +{ + gpio_free(TOSA_GPIO_TC6393XB_L3V_ON); + gpio_free(TOSA_GPIO_TC6393XB_SUSPEND); + gpio_free(TOSA_GPIO_TC6393XB_REST_IN); + + return 0; +} + +static int tosa_tc6393xb_resume(struct platform_device *dev) +{ + gpio_set_value(TOSA_GPIO_TC6393XB_SUSPEND, 1); + mdelay(10); + gpio_set_value(TOSA_GPIO_TC6393XB_L3V_ON, 1); + mdelay(10); + + return 0; +} + +static int tosa_tc6393xb_suspend(struct platform_device *dev) +{ + gpio_set_value(TOSA_GPIO_TC6393XB_L3V_ON, 0); + gpio_set_value(TOSA_GPIO_TC6393XB_SUSPEND, 0); + return 0; +} + +static struct mtd_partition tosa_nand_partition[] = { + { + .name = "smf", + .offset = 0, + .size = 7 * 1024 * 1024, + }, + { + .name = "root", + .offset = MTDPART_OFS_APPEND, + .size = 28 * 1024 * 1024, + }, + { + .name = "home", + .offset = MTDPART_OFS_APPEND, + .size = MTDPART_SIZ_FULL, + }, +}; + +static uint8_t scan_ff_pattern[] = { 0xff, 0xff }; + +static struct nand_bbt_descr tosa_tc6393xb_nand_bbt = { + .options = 0, + .offs = 4, + .len = 2, + .pattern = scan_ff_pattern +}; + +static struct tmio_nand_data tosa_tc6393xb_nand_config = { + .num_partitions = ARRAY_SIZE(tosa_nand_partition), + .partition = tosa_nand_partition, + .badblock_pattern = &tosa_tc6393xb_nand_bbt, +}; + +static struct tc6393xb_platform_data tosa_tc6393xb_setup = { + .scr_pll2cr = 0x0cc1, + .scr_gper = 0x3300, + .scr_gpo_dsr = + TOSA_TC6393XB_GPIO_BIT(TOSA_GPIO_CARD_VCC_ON), + .scr_gpo_doecr = + TOSA_TC6393XB_GPIO_BIT(TOSA_GPIO_CARD_VCC_ON), + + .irq_base = IRQ_BOARD_START, + .gpio_base = TOSA_TC6393XB_GPIO_BASE, + + .enable = tosa_tc6393xb_enable, + .disable = tosa_tc6393xb_disable, + .suspend = tosa_tc6393xb_suspend, + .resume = tosa_tc6393xb_resume, + + .nand_data = &tosa_tc6393xb_nand_config, +}; + + +static struct platform_device tc6393xb_device = { + .name = "tc6393xb", + .id = -1, + .dev = { + .platform_data = &tosa_tc6393xb_setup, + }, + .num_resources = ARRAY_SIZE(tc6393xb_resources), + .resource = tc6393xb_resources, +}; + +static struct tosa_bt_data tosa_bt_data = { + .gpio_pwr = TOSA_GPIO_BT_PWR_EN, + .gpio_reset = TOSA_GPIO_BT_RESET, +}; + +static struct platform_device tosa_bt_device = { + .name = "tosa-bt", + .id = -1, + .dev.platform_data = &tosa_bt_data, +}; + + static struct platform_device *devices[] __initdata = { &tosascoop_device, &tosascoop_jc_device, + &tc6393xb_device, + &tosa_power_device, &tosakbd_device, &tosa_gpio_keys_device, &tosaled_device, + &tosa_bt_device, }; static void tosa_poweroff(void) { - gpio_direction_output(TOSA_GPIO_ON_RESET, 0); - gpio_set_value(TOSA_GPIO_ON_RESET, 1); - - mdelay(1000); - arm_machine_restart('h'); + arm_machine_restart('g'); } static void tosa_restart(char mode) @@ -485,10 +775,14 @@ static void tosa_restart(char mode) static void __init tosa_init(void) { + int dummy; + pxa2xx_mfp_config(ARRAY_AND_SIZE(tosa_pin_config)); gpio_set_wake(MFP_PIN_GPIO1, 1); /* We can't pass to gpio-keys since it will drop the Reset altfunc */ + init_gpio_reset(TOSA_GPIO_ON_RESET, 0); + pm_power_off = tosa_poweroff; arm_pm_restart = tosa_restart; @@ -497,12 +791,18 @@ static void __init tosa_init(void) /* enable batt_fault */ PMCR = 0x01; + dummy = gpiochip_reserve(TOSA_SCOOP_GPIO_BASE, 12); + dummy = gpiochip_reserve(TOSA_SCOOP_JC_GPIO_BASE, 12); + dummy = gpiochip_reserve(TOSA_TC6393XB_GPIO_BASE, 16); + pxa_set_mci_info(&tosa_mci_platform_data); pxa_set_udc_info(&udc_info); pxa_set_ficp_info(&tosa_ficp_platform_data); pxa_set_i2c_info(NULL); platform_scoop_config = &tosa_pcmcia_config; + clk_add_alias("CLK_CK3P6MI", &tc6393xb_device.dev, "GPIO11_CLK", NULL); + platform_add_devices(devices, ARRAY_SIZE(devices)); } diff --git a/arch/arm/mach-pxa/trizeps4.c b/arch/arm/mach-pxa/trizeps4.c index 931885d86b9..a13dbf3c2c0 100644 --- a/arch/arm/mach-pxa/trizeps4.c +++ b/arch/arm/mach-pxa/trizeps4.c @@ -22,8 +22,8 @@ #include <linux/fb.h> #include <linux/ioport.h> #include <linux/delay.h> -#include <linux/serial_8250.h> -#include <linux/mtd/mtd.h> +#include <linux/gpio.h> +#include <linux/dm9000.h> #include <linux/mtd/physmap.h> #include <linux/mtd/partitions.h> @@ -31,7 +31,6 @@ #include <asm/setup.h> #include <asm/memory.h> #include <asm/mach-types.h> -#include <asm/hardware.h> #include <asm/irq.h> #include <asm/sizes.h> @@ -40,40 +39,148 @@ #include <asm/mach/irq.h> #include <asm/mach/flash.h> -#include <asm/arch/pxa-regs.h> -#include <asm/arch/pxa2xx-gpio.h> -#include <asm/arch/trizeps4.h> -#include <asm/arch/audio.h> -#include <asm/arch/pxafb.h> -#include <asm/arch/mmc.h> -#include <asm/arch/irda.h> -#include <asm/arch/ohci.h> +#include <mach/hardware.h> +#include <mach/pxa-regs.h> +#include <mach/pxa2xx-regs.h> +#include <mach/mfp-pxa27x.h> +#include <mach/pxa2xx_spi.h> +#include <mach/trizeps4.h> +#include <mach/audio.h> +#include <mach/pxafb.h> +#include <mach/mmc.h> +#include <mach/irda.h> +#include <mach/ohci.h> +#include <mach/i2c.h> #include "generic.h" #include "devices.h" -/******************************************************************************************** +/* comment out the following line if you want to use the + * Standard UART from PXA for serial / irda transmission + * and acivate it if you have status leds connected */ +#define STATUS_LEDS_ON_STUART_PINS 1 + +/***************************************************************************** + * MultiFunctionPins of CPU + *****************************************************************************/ +static unsigned long trizeps4_pin_config[] __initdata = { + /* Chip Selects */ + GPIO15_nCS_1, /* DiskOnChip CS */ + GPIO93_GPIO, /* TRIZEPS4_DOC_IRQ */ + GPIO94_GPIO, /* DOC lock */ + + GPIO78_nCS_2, /* DM9000 CS */ + GPIO101_GPIO, /* TRIZEPS4_ETH_IRQ */ + + GPIO79_nCS_3, /* Logic CS */ + GPIO0_GPIO | WAKEUP_ON_EDGE_RISE, /* Logic irq */ + + /* LCD - 16bpp Active TFT */ + GPIO58_LCD_LDD_0, + GPIO59_LCD_LDD_1, + GPIO60_LCD_LDD_2, + GPIO61_LCD_LDD_3, + GPIO62_LCD_LDD_4, + GPIO63_LCD_LDD_5, + GPIO64_LCD_LDD_6, + GPIO65_LCD_LDD_7, + GPIO66_LCD_LDD_8, + GPIO67_LCD_LDD_9, + GPIO68_LCD_LDD_10, + GPIO69_LCD_LDD_11, + GPIO70_LCD_LDD_12, + GPIO71_LCD_LDD_13, + GPIO72_LCD_LDD_14, + GPIO73_LCD_LDD_15, + GPIO74_LCD_FCLK, + GPIO75_LCD_LCLK, + GPIO76_LCD_PCLK, + GPIO77_LCD_BIAS, + + /* UART */ + GPIO9_FFUART_CTS, + GPIO10_FFUART_DCD, + GPIO16_FFUART_TXD, + GPIO33_FFUART_DSR, + GPIO38_FFUART_RI, + GPIO82_FFUART_DTR, + GPIO83_FFUART_RTS, + GPIO96_FFUART_RXD, + + GPIO42_BTUART_RXD, + GPIO43_BTUART_TXD, + GPIO44_BTUART_CTS, + GPIO45_BTUART_RTS, +#ifdef STATUS_LEDS_ON_STUART_PINS + GPIO46_GPIO, + GPIO47_GPIO, +#else + GPIO46_STUART_RXD, + GPIO47_STUART_TXD, +#endif + /* PCMCIA */ + GPIO11_GPIO, /* TRIZEPS4_CD_IRQ */ + GPIO13_GPIO, /* TRIZEPS4_READY_NINT */ + GPIO48_nPOE, + GPIO49_nPWE, + GPIO50_nPIOR, + GPIO51_nPIOW, + GPIO54_nPCE_2, + GPIO55_nPREG, + GPIO56_nPWAIT, + GPIO57_nIOIS16, + GPIO102_nPCE_1, + GPIO104_PSKTSEL, + + /* MultiMediaCard */ + GPIO32_MMC_CLK, + GPIO92_MMC_DAT_0, + GPIO109_MMC_DAT_1, + GPIO110_MMC_DAT_2, + GPIO111_MMC_DAT_3, + GPIO112_MMC_CMD, + GPIO12_GPIO, /* TRIZEPS4_MMC_IRQ */ + + /* USB OHCI */ + GPIO88_USBH1_PWR, /* USBHPWR1 */ + GPIO89_USBH1_PEN, /* USBHPEN1 */ + + /* I2C */ + GPIO117_I2C_SCL, + GPIO118_I2C_SDA, +}; + +static unsigned long trizeps4wl_pin_config[] __initdata = { + /* SSP 2 */ + GPIO14_SSP2_SFRM, + GPIO19_SSP2_SCLK, + GPIO53_GPIO, /* TRIZEPS4_SPI_IRQ */ + GPIO86_SSP2_RXD, + GPIO87_SSP2_TXD, +}; + +/**************************************************************************** * ONBOARD FLASH - ********************************************************************************************/ + ****************************************************************************/ static struct mtd_partition trizeps4_partitions[] = { { .name = "Bootloader", .offset = 0x00000000, .size = 0x00040000, .mask_flags = MTD_WRITEABLE /* force read-only */ - },{ + }, { .name = "Backup", .offset = 0x00040000, .size = 0x00040000, - },{ + }, { .name = "Image", .offset = 0x00080000, .size = 0x01080000, - },{ + }, { .name = "IPSM", .offset = 0x01100000, .size = 0x00e00000, - },{ + }, { .name = "Registry", .offset = 0x01f00000, .size = MTDPART_SIZ_FULL, @@ -104,9 +211,9 @@ static struct platform_device flash_device = { .num_resources = 1, }; -/******************************************************************************************** +/**************************************************************************** * DAVICOM DM9000 Ethernet - ********************************************************************************************/ + ****************************************************************************/ static struct resource dm9000_resources[] = { [0] = { .start = TRIZEPS4_ETH_PHYS+0x300, @@ -121,76 +228,68 @@ static struct resource dm9000_resources[] = { [2] = { .start = TRIZEPS4_ETH_IRQ, .end = TRIZEPS4_ETH_IRQ, - .flags = (IORESOURCE_IRQ | IRQT_RISING), + .flags = IORESOURCE_IRQ | IORESOURCE_IRQ_HIGHEDGE, }, }; +static struct dm9000_plat_data tri_dm9000_platdata = { + .flags = DM9000_PLATF_32BITONLY, +}; + static struct platform_device dm9000_device = { .name = "dm9000", .id = -1, .num_resources = ARRAY_SIZE(dm9000_resources), .resource = dm9000_resources, + .dev = { + .platform_data = &tri_dm9000_platdata, + } }; -/******************************************************************************************** - * PXA270 serial ports - ********************************************************************************************/ -static struct plat_serial8250_port tri_serial_ports[] = { -#ifdef CONFIG_SERIAL_PXA - /* this uses the own PXA driver */ +/**************************************************************************** + * LED's on GPIO pins of PXA + ****************************************************************************/ +static struct gpio_led trizeps4_led[] = { +#ifdef STATUS_LEDS_ON_STUART_PINS { - 0, - }, -#else - /* this uses the generic 8520 driver */ - [0] = { - .membase = (void *)&FFUART, - .irq = IRQ_FFUART, - .flags = UPF_BOOT_AUTOCONF, - .iotype = UPIO_MEM32, - .regshift = 2, - .uartclk = (921600*16), - }, - [1] = { - .membase = (void *)&BTUART, - .irq = IRQ_BTUART, - .flags = UPF_BOOT_AUTOCONF, - .iotype = UPIO_MEM32, - .regshift = 2, - .uartclk = (921600*16), + .name = "led0:orange:heartbeat", /* */ + .default_trigger = "heartbeat", + .gpio = GPIO_HEARTBEAT_LED, + .active_low = 1, }, { - 0, + .name = "led1:yellow:cpubusy", /* */ + .default_trigger = "cpu-busy", + .gpio = GPIO_SYS_BUSY_LED, + .active_low = 1, }, #endif }; -static struct platform_device uart_devices = { - .name = "serial8250", - .id = 0, - .dev = { - .platform_data = tri_serial_ports, - }, - .num_resources = 0, - .resource = NULL, +static struct gpio_led_platform_data trizeps4_led_data = { + .leds = trizeps4_led, + .num_leds = ARRAY_SIZE(trizeps4_led), }; -/******************************************************************************************** - * PXA270 ac97 sound codec - ********************************************************************************************/ -static struct platform_device ac97_audio_device = { - .name = "pxa2xx-ac97", +static struct platform_device leds_devices = { + .name = "leds-gpio", .id = -1, + .dev = { + .platform_data = &trizeps4_led_data, + }, }; -static struct platform_device * trizeps4_devices[] __initdata = { +static struct platform_device *trizeps4_devices[] __initdata = { &flash_device, - &uart_devices, &dm9000_device, - &ac97_audio_device, + &leds_devices, +}; + +static struct platform_device *trizeps4wl_devices[] __initdata = { + &flash_device, + &leds_devices, }; -#ifdef CONFIG_MACH_TRIZEPS4_CONXS static short trizeps_conxs_bcr; /* PCCARD power switching supports only 3,3V */ @@ -200,107 +299,63 @@ void board_pcmcia_power(int power) /* switch power on, put in reset and enable buffers */ trizeps_conxs_bcr |= power; trizeps_conxs_bcr |= ConXS_BCR_CF_RESET; - trizeps_conxs_bcr &= ~(ConXS_BCR_CF_BUF_EN); - ConXS_BCR = trizeps_conxs_bcr; + trizeps_conxs_bcr &= ~ConXS_BCR_CF_BUF_EN; + BCR_writew(trizeps_conxs_bcr); /* wait a little */ udelay(2000); /* take reset away */ - trizeps_conxs_bcr &= ~(ConXS_BCR_CF_RESET); - ConXS_BCR = trizeps_conxs_bcr; + trizeps_conxs_bcr &= ~ConXS_BCR_CF_RESET; + BCR_writew(trizeps_conxs_bcr); udelay(2000); } else { /* put in reset */ trizeps_conxs_bcr |= ConXS_BCR_CF_RESET; - ConXS_BCR = trizeps_conxs_bcr; + BCR_writew(trizeps_conxs_bcr); udelay(1000); /* switch power off */ - trizeps_conxs_bcr &= ~(0xf); - ConXS_BCR = trizeps_conxs_bcr; - + trizeps_conxs_bcr &= ~0xf; + BCR_writew(trizeps_conxs_bcr); } - pr_debug("%s: o%s 0x%x\n", __func__, power ? "n": "ff", trizeps_conxs_bcr); + pr_debug("%s: o%s 0x%x\n", __func__, power ? "n" : "ff", + trizeps_conxs_bcr); } +EXPORT_SYMBOL(board_pcmcia_power); /* backlight power switching for LCD panel */ static void board_backlight_power(int on) { - if (on) { + if (on) trizeps_conxs_bcr |= ConXS_BCR_L_DISP; - } else { + else trizeps_conxs_bcr &= ~ConXS_BCR_L_DISP; - } - pr_debug("%s: o%s 0x%x\n", __func__, on ? "n" : "ff", trizeps_conxs_bcr); - ConXS_BCR = trizeps_conxs_bcr; -} -/* Powersupply for MMC/SD cardslot */ -static void board_mci_power(struct device *dev, unsigned int vdd) -{ - struct pxamci_platform_data* p_d = dev->platform_data; - - if (( 1 << vdd) & p_d->ocr_mask) { - pr_debug("%s: on\n", __func__); - /* FIXME fill in values here */ - } else { - pr_debug("%s: off\n", __func__); - /* FIXME fill in values here */ - } + pr_debug("%s: o%s 0x%x\n", __func__, on ? "n" : "ff", + trizeps_conxs_bcr); + BCR_writew(trizeps_conxs_bcr); } -static short trizeps_conxs_ircr; - -/* Switch modes and Power for IRDA receiver */ -static void board_irda_mode(struct device *dev, int mode) -{ - unsigned long flags; - - local_irq_save(flags); - if (mode & IR_SIRMODE) { - /* Slow mode */ - trizeps_conxs_ircr &= ~ConXS_IRCR_MODE; - } else if (mode & IR_FIRMODE) { - /* Fast mode */ - trizeps_conxs_ircr |= ConXS_IRCR_MODE; - } - if (mode & IR_OFF) { - trizeps_conxs_ircr |= ConXS_IRCR_SD; - } else { - trizeps_conxs_ircr &= ~ConXS_IRCR_SD; - } - /* FIXME write values to register */ - local_irq_restore(flags); -} - -#else -/* for other baseboards define dummies */ -void board_pcmcia_power(int power) {;} -#define board_backlight_power NULL -#define board_mci_power NULL -#define board_irda_mode NULL - -#endif /* CONFIG_MACH_TRIZEPS4_CONXS */ -EXPORT_SYMBOL(board_pcmcia_power); +/* a I2C based RTC is known on CONXS board */ +static struct i2c_board_info trizeps4_i2c_devices[] __initdata = { + { I2C_BOARD_INFO("rtc-pcf8593", 0x51) } +}; -static int trizeps4_mci_init(struct device *dev, irq_handler_t mci_detect_int, void *data) +/**************************************************************************** + * MMC card slot external to module + ****************************************************************************/ +static int trizeps4_mci_init(struct device *dev, irq_handler_t mci_detect_int, + void *data) { int err; - /* setup GPIO for PXA27x MMC controller */ - pxa_gpio_mode(GPIO32_MMCCLK_MD); - pxa_gpio_mode(GPIO112_MMCCMD_MD); - pxa_gpio_mode(GPIO92_MMCDAT0_MD); - pxa_gpio_mode(GPIO109_MMCDAT1_MD); - pxa_gpio_mode(GPIO110_MMCDAT2_MD); - pxa_gpio_mode(GPIO111_MMCDAT3_MD); - - pxa_gpio_mode(GPIO_MMC_DET | GPIO_IN); err = request_irq(TRIZEPS4_MMC_IRQ, mci_detect_int, - IRQF_DISABLED | IRQF_TRIGGER_RISING, - "MMC card detect", data); - if (err) - printk(KERN_ERR "trizeps4_mci_init: MMC/SD: can't request MMC card detect IRQ\n"); - - return err; + IRQF_DISABLED | IRQF_TRIGGER_RISING | IRQF_SAMPLE_RANDOM, + "MMC card detect", data); + if (err) { + printk(KERN_ERR "trizeps4_mci_init: MMC/SD: can't request" + "MMC card detect IRQ\n"); + return -1; + } + return 0; } static void trizeps4_mci_exit(struct device *dev, void *data) @@ -310,39 +365,69 @@ static void trizeps4_mci_exit(struct device *dev, void *data) static struct pxamci_platform_data trizeps4_mci_platform_data = { .ocr_mask = MMC_VDD_32_33|MMC_VDD_33_34, + .detect_delay = 1, .init = trizeps4_mci_init, .exit = trizeps4_mci_exit, - .setpower = board_mci_power, + .get_ro = NULL, /* write-protection not supported */ + .setpower = NULL, /* power-switching not supported */ }; -static struct pxaficp_platform_data trizeps4_ficp_platform_data = { - .transceiver_cap = IR_SIRMODE | IR_FIRMODE | IR_OFF, - .transceiver_mode = board_irda_mode, -}; +/**************************************************************************** + * IRDA mode switching on stuart + ****************************************************************************/ +#ifndef STATUS_LEDS_ON_STUART_PINS +static short trizeps_conxs_ircr; -static int trizeps4_ohci_init(struct device *dev) +static int trizeps4_irda_startup(struct device *dev) { - /* setup Port1 GPIO pin. */ - pxa_gpio_mode( 88 | GPIO_ALT_FN_1_IN); /* USBHPWR1 */ - pxa_gpio_mode( 89 | GPIO_ALT_FN_2_OUT); /* USBHPEN1 */ - - /* Set the Power Control Polarity Low and Power Sense - Polarity Low to active low. */ - UHCHR = (UHCHR | UHCHR_PCPL | UHCHR_PSPL) & - ~(UHCHR_SSEP1 | UHCHR_SSEP2 | UHCHR_SSEP3 | UHCHR_SSE); - + trizeps_conxs_ircr &= ~ConXS_IRCR_SD; + IRCR_writew(trizeps_conxs_ircr); return 0; } -static void trizeps4_ohci_exit(struct device *dev) +static void trizeps4_irda_shutdown(struct device *dev) +{ + trizeps_conxs_ircr |= ConXS_IRCR_SD; + IRCR_writew(trizeps_conxs_ircr); +} + +static void trizeps4_irda_transceiver_mode(struct device *dev, int mode) { - ; + unsigned long flags; + + local_irq_save(flags); + /* Switch mode */ + if (mode & IR_SIRMODE) + trizeps_conxs_ircr &= ~ConXS_IRCR_MODE; /* Slow mode */ + else if (mode & IR_FIRMODE) { + trizeps_conxs_ircr |= ConXS_IRCR_MODE; /* Fast mode */ + + /* Switch power */ + if (mode & IR_OFF) + trizeps_conxs_ircr |= ConXS_IRCR_SD; + else + trizeps_conxs_ircr &= ~ConXS_IRCR_SD; + + IRCR_writew(trizeps_conxs_ircr); + local_irq_restore(flags); + + pxa2xx_transceiver_mode(dev, mode); } +static struct pxaficp_platform_data trizeps4_ficp_platform_data = { + .transceiver_cap = IR_SIRMODE | IR_FIRMODE | IR_OFF, + .transceiver_mode = trizeps4_irda_transceiver_mode, + .startup = trizeps4_irda_startup, + .shutdown = trizeps4_irda_shutdown, +}; +#endif + +/**************************************************************************** + * OHCI USB port + ****************************************************************************/ static struct pxaohci_platform_data trizeps4_ohci_platform_data = { .port_mode = PMM_PERPORT_MODE, - .init = trizeps4_ohci_init, - .exit = trizeps4_ohci_exit, + .flags = ENABLE_PORT_ALL | POWER_CONTROL_LOW | POWER_SENSE_LOW, }; static struct map_desc trizeps4_io_desc[] __initdata = { @@ -379,104 +464,80 @@ static struct map_desc trizeps4_io_desc[] __initdata = { }; static struct pxafb_mode_info sharp_lcd_mode = { - .pixclock = 78000, - .xres = 640, - .yres = 480, - .bpp = 8, - .hsync_len = 4, - .left_margin = 4, - .right_margin = 4, - .vsync_len = 2, - .upper_margin = 0, - .lower_margin = 0, - .sync = FB_SYNC_HOR_HIGH_ACT | FB_SYNC_VERT_HIGH_ACT, - .cmap_greyscale = 0, + .pixclock = 78000, + .xres = 640, + .yres = 480, + .bpp = 8, + .hsync_len = 4, + .left_margin = 4, + .right_margin = 4, + .vsync_len = 2, + .upper_margin = 0, + .lower_margin = 0, + .sync = FB_SYNC_HOR_HIGH_ACT | FB_SYNC_VERT_HIGH_ACT, + .cmap_greyscale = 0, }; static struct pxafb_mach_info sharp_lcd = { - .modes = &sharp_lcd_mode, - .num_modes = 1, - .cmap_inverse = 0, - .cmap_static = 0, - .lccr0 = LCCR0_Color | LCCR0_Pas | LCCR0_Dual, - .lccr3 = 0x0340ff02, - .pxafb_backlight_power = board_backlight_power, + .modes = &sharp_lcd_mode, + .num_modes = 1, + .lcd_conn = LCD_COLOR_DSTN_16BPP | LCD_PCLK_EDGE_FALL, + .cmap_inverse = 0, + .cmap_static = 0, + .pxafb_backlight_power = board_backlight_power, }; static struct pxafb_mode_info toshiba_lcd_mode = { - .pixclock = 39720, - .xres = 640, - .yres = 480, - .bpp = 8, - .hsync_len = 63, - .left_margin = 12, - .right_margin = 12, - .vsync_len = 4, - .upper_margin = 32, - .lower_margin = 10, - .sync = 0, - .cmap_greyscale = 0, + .pixclock = 39720, + .xres = 640, + .yres = 480, + .bpp = 8, + .hsync_len = 63, + .left_margin = 12, + .right_margin = 12, + .vsync_len = 4, + .upper_margin = 32, + .lower_margin = 10, + .sync = 0, + .cmap_greyscale = 0, }; static struct pxafb_mach_info toshiba_lcd = { - .modes = &toshiba_lcd_mode, - .num_modes = 1, - .cmap_inverse = 0, - .cmap_static = 0, - .lccr0 = LCCR0_Color | LCCR0_Act, - .lccr3 = 0x03400002, - .pxafb_backlight_power = board_backlight_power, + .modes = &toshiba_lcd_mode, + .num_modes = 1, + .lcd_conn = (LCD_COLOR_TFT_16BPP | LCD_PCLK_EDGE_FALL), + .cmap_inverse = 0, + .cmap_static = 0, + .pxafb_backlight_power = board_backlight_power, }; static void __init trizeps4_init(void) { - platform_add_devices(trizeps4_devices, ARRAY_SIZE(trizeps4_devices)); + pxa2xx_mfp_config(ARRAY_AND_SIZE(trizeps4_pin_config)); + if (machine_is_trizeps4wl()) { + pxa2xx_mfp_config(ARRAY_AND_SIZE(trizeps4wl_pin_config)); + platform_add_devices(trizeps4wl_devices, + ARRAY_SIZE(trizeps4wl_devices)); + } else { + platform_add_devices(trizeps4_devices, + ARRAY_SIZE(trizeps4_devices)); + } -/* set_pxa_fb_info(&sharp_lcd); */ - set_pxa_fb_info(&toshiba_lcd); + if (0) /* dont know how to determine LCD */ + set_pxa_fb_info(&sharp_lcd); + else + set_pxa_fb_info(&toshiba_lcd); pxa_set_mci_info(&trizeps4_mci_platform_data); +#ifndef STATUS_LEDS_ON_STUART_PINS pxa_set_ficp_info(&trizeps4_ficp_platform_data); +#endif pxa_set_ohci_info(&trizeps4_ohci_platform_data); -} - -static void __init trizeps4_map_io(void) -{ - pxa_map_io(); - iotable_init(trizeps4_io_desc, ARRAY_SIZE(trizeps4_io_desc)); + pxa_set_ac97_info(NULL); + pxa_set_i2c_info(NULL); + i2c_register_board_info(0, trizeps4_i2c_devices, + ARRAY_SIZE(trizeps4_i2c_devices)); - /* for DiskOnChip */ - pxa_gpio_mode(GPIO15_nCS_1_MD); - - /* for off-module PIC on ConXS board */ - pxa_gpio_mode(GPIO_PIC | GPIO_IN); - - /* UCB1400 irq */ - pxa_gpio_mode(GPIO_UCB1400 | GPIO_IN); - - /* for DM9000 LAN */ - pxa_gpio_mode(GPIO78_nCS_2_MD); - pxa_gpio_mode(GPIO_DM9000 | GPIO_IN); - - /* for PCMCIA device */ - pxa_gpio_mode(GPIO_PCD | GPIO_IN); - pxa_gpio_mode(GPIO_PRDY | GPIO_IN); - - /* for I2C adapter */ - pxa_gpio_mode(GPIO117_I2CSCL_MD); - pxa_gpio_mode(GPIO118_I2CSDA_MD); - - /* MMC_DET s.o. */ - pxa_gpio_mode(GPIO_MMC_DET | GPIO_IN); - - /* whats that for ??? */ - pxa_gpio_mode(GPIO79_nCS_3_MD); - -#ifdef CONFIG_LEDS - pxa_gpio_mode( GPIO_SYS_BUSY_LED | GPIO_OUT); /* LED1 */ - pxa_gpio_mode( GPIO_HEARTBEAT_LED | GPIO_OUT); /* LED2 */ -#endif -#ifdef CONFIG_MACH_TRIZEPS4_CONXS #ifdef CONFIG_IDE_PXA_CF /* if boot direct from compact flash dont disable power */ trizeps_conxs_bcr = 0x0009; @@ -484,17 +545,24 @@ static void __init trizeps4_map_io(void) /* this is the reset value */ trizeps_conxs_bcr = 0x00A0; #endif - ConXS_BCR = trizeps_conxs_bcr; -#endif + BCR_writew(trizeps_conxs_bcr); + board_backlight_power(1); +} - PWER = 0x00000002; - PFER = 0x00000000; - PRER = 0x00000002; - PGSR0 = 0x0158C000; - PGSR1 = 0x00FF0080; - PGSR2 = 0x0001C004; - /* Stop 3.6MHz and drive HIGH to PCMCIA and CS */ - PCFR |= PCFR_OPDE; +static void __init trizeps4_map_io(void) +{ + pxa_map_io(); + iotable_init(trizeps4_io_desc, ARRAY_SIZE(trizeps4_io_desc)); + + if ((MSC0 & 0x8) && (BOOT_DEF & 0x1)) { + /* if flash is 16 bit wide its a Trizeps4 WL */ + __machine_arch_type = MACH_TYPE_TRIZEPS4WL; + trizeps4_flash_data[0].width = 2; + } else { + /* if flash is 32 bit wide its a Trizeps4 */ + __machine_arch_type = MACH_TYPE_TRIZEPS4; + trizeps4_flash_data[0].width = 4; + } } MACHINE_START(TRIZEPS4, "Keith und Koep Trizeps IV module") @@ -508,3 +576,13 @@ MACHINE_START(TRIZEPS4, "Keith und Koep Trizeps IV module") .timer = &pxa_timer, MACHINE_END +MACHINE_START(TRIZEPS4WL, "Keith und Koep Trizeps IV-WL module") + /* MAINTAINER("Jürgen Schindele") */ + .phys_io = 0x40000000, + .io_pg_offst = (io_p2v(0x40000000) >> 18) & 0xfffc, + .boot_params = TRIZEPS4_SDRAM_BASE + 0x100, + .init_machine = trizeps4_init, + .map_io = trizeps4_map_io, + .init_irq = pxa27x_init_irq, + .timer = &pxa_timer, +MACHINE_END diff --git a/arch/arm/mach-pxa/viper.c b/arch/arm/mach-pxa/viper.c new file mode 100644 index 00000000000..d7632f63603 --- /dev/null +++ b/arch/arm/mach-pxa/viper.c @@ -0,0 +1,951 @@ +/* + * linux/arch/arm/mach-pxa/viper.c + * + * Support for the Arcom VIPER SBC. + * + * Author: Ian Campbell + * Created: Feb 03, 2003 + * Copyright: Arcom Control Systems + * + * Maintained by Marc Zyngier <maz@misterjones.org> + * <marc.zyngier@altran.com> + * + * Based on lubbock.c: + * Author: Nicolas Pitre + * Created: Jun 15, 2001 + * Copyright: MontaVista Software Inc. + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ + +#include <linux/types.h> +#include <linux/memory.h> +#include <linux/cpu.h> +#include <linux/cpufreq.h> +#include <linux/delay.h> +#include <linux/fs.h> +#include <linux/init.h> +#include <linux/interrupt.h> +#include <linux/major.h> +#include <linux/module.h> +#include <linux/pm.h> +#include <linux/sched.h> +#include <linux/gpio.h> +#include <linux/i2c-gpio.h> +#include <linux/serial_8250.h> +#include <linux/smc91x.h> +#include <linux/pwm_backlight.h> +#include <linux/usb/isp116x.h> +#include <linux/mtd/mtd.h> +#include <linux/mtd/partitions.h> +#include <linux/mtd/physmap.h> + +#include <mach/pxa-regs.h> +#include <mach/pxa2xx-regs.h> +#include <mach/bitfield.h> +#include <mach/audio.h> +#include <mach/pxafb.h> +#include <mach/mfp-pxa25x.h> +#include <mach/i2c.h> +#include <mach/viper.h> + +#include <asm/setup.h> +#include <asm/mach-types.h> +#include <asm/irq.h> +#include <asm/sizes.h> + +#include <asm/mach/arch.h> +#include <asm/mach/map.h> +#include <asm/mach/irq.h> + +#include "generic.h" +#include "devices.h" + +static unsigned int icr; + +static void viper_icr_set_bit(unsigned int bit) +{ + icr |= bit; + VIPER_ICR = icr; +} + +static void viper_icr_clear_bit(unsigned int bit) +{ + icr &= ~bit; + VIPER_ICR = icr; +} + +/* This function is used from the pcmcia module to reset the CF */ +void viper_cf_rst(int state) +{ + if (state) + viper_icr_set_bit(VIPER_ICR_CF_RST); + else + viper_icr_clear_bit(VIPER_ICR_CF_RST); +} +EXPORT_SYMBOL(viper_cf_rst); + +/* + * The CPLD version register was not present on VIPER boards prior to + * v2i1. On v1 boards where the version register is not present we + * will just read back the previous value from the databus. + * + * Therefore we do two reads. The first time we write 0 to the + * (read-only) register before reading and the second time we write + * 0xff first. If the two reads do not match or they read back as 0xff + * or 0x00 then we have version 1 hardware. + */ +static u8 viper_hw_version(void) +{ + u8 v1, v2; + unsigned long flags; + + local_irq_save(flags); + + VIPER_VERSION = 0; + v1 = VIPER_VERSION; + VIPER_VERSION = 0xff; + v2 = VIPER_VERSION; + + v1 = (v1 != v2 || v1 == 0xff) ? 0 : v1; + + local_irq_restore(flags); + return v1; +} + +/* CPU sysdev */ +static int viper_cpu_suspend(struct sys_device *sysdev, pm_message_t state) +{ + viper_icr_set_bit(VIPER_ICR_R_DIS); + return 0; +} + +static int viper_cpu_resume(struct sys_device *sysdev) +{ + viper_icr_clear_bit(VIPER_ICR_R_DIS); + return 0; +} + +static struct sysdev_driver viper_cpu_sysdev_driver = { + .suspend = viper_cpu_suspend, + .resume = viper_cpu_resume, +}; + +static unsigned int current_voltage_divisor; + +/* + * If force is not true then step from existing to new divisor. If + * force is true then jump straight to the new divisor. Stepping is + * used because if the jump in voltage is too large, the VCC can dip + * too low and the regulator cuts out. + * + * force can be used to initialize the divisor to a know state by + * setting the value for the current clock speed, since we are already + * running at that speed we know the voltage should be pretty close so + * the jump won't be too large + */ +static void viper_set_core_cpu_voltage(unsigned long khz, int force) +{ + int i = 0; + unsigned int divisor = 0; + const char *v; + + if (khz < 200000) { + v = "1.0"; divisor = 0xfff; + } else if (khz < 300000) { + v = "1.1"; divisor = 0xde5; + } else { + v = "1.3"; divisor = 0x325; + } + + pr_debug("viper: setting CPU core voltage to %sV at %d.%03dMHz\n", + v, (int)khz / 1000, (int)khz % 1000); + +#define STEP 0x100 + do { + int step; + + if (force) + step = divisor; + else if (current_voltage_divisor < divisor - STEP) + step = current_voltage_divisor + STEP; + else if (current_voltage_divisor > divisor + STEP) + step = current_voltage_divisor - STEP; + else + step = divisor; + force = 0; + + gpio_set_value(VIPER_PSU_CLK_GPIO, 0); + gpio_set_value(VIPER_PSU_nCS_LD_GPIO, 0); + + for (i = 1 << 11 ; i > 0 ; i >>= 1) { + udelay(1); + + gpio_set_value(VIPER_PSU_DATA_GPIO, step & i); + udelay(1); + + gpio_set_value(VIPER_PSU_CLK_GPIO, 1); + udelay(1); + + gpio_set_value(VIPER_PSU_CLK_GPIO, 0); + } + udelay(1); + + gpio_set_value(VIPER_PSU_nCS_LD_GPIO, 1); + udelay(1); + + gpio_set_value(VIPER_PSU_nCS_LD_GPIO, 0); + + current_voltage_divisor = step; + } while (current_voltage_divisor != divisor); +} + +/* Interrupt handling */ +static unsigned long viper_irq_enabled_mask; + +static void viper_ack_irq(unsigned int irq) +{ + int viper_irq = irq - PXA_ISA_IRQ(0); + + if (viper_irq < 8) + VIPER_LO_IRQ_STATUS = 1 << viper_irq; + else + VIPER_HI_IRQ_STATUS = 1 << (viper_irq - 8); +} + +static void viper_mask_irq(unsigned int irq) +{ + viper_irq_enabled_mask &= ~(1 << (irq - PXA_ISA_IRQ(0))); +} + +static void viper_unmask_irq(unsigned int irq) +{ + viper_irq_enabled_mask |= (1 << (irq - PXA_ISA_IRQ(0))); +} + +static inline unsigned long viper_irq_pending(void) +{ + return (VIPER_HI_IRQ_STATUS << 8 | VIPER_LO_IRQ_STATUS) & + viper_irq_enabled_mask; +} + +static void viper_irq_handler(unsigned int irq, struct irq_desc *desc) +{ + unsigned long pending; + + pending = viper_irq_pending(); + do { + if (likely(pending)) { + irq = PXA_ISA_IRQ(0) + __ffs(pending); + generic_handle_irq(irq); + } + pending = viper_irq_pending(); + } while (pending); +} + +static struct irq_chip viper_irq_chip = { + .name = "ISA", + .ack = viper_ack_irq, + .mask = viper_mask_irq, + .unmask = viper_unmask_irq +}; + +static void __init viper_init_irq(void) +{ + const int isa_irqs[] = { 3, 4, 5, 6, 7, 10, 11, 12, 9, 14, 15 }; + int irq; + int isa_irq; + + pxa25x_init_irq(); + + /* setup ISA IRQs */ + for (irq = 0; irq < ARRAY_SIZE(isa_irqs); irq++) { + isa_irq = isa_irqs[irq]; + set_irq_chip(isa_irq, &viper_irq_chip); + set_irq_handler(isa_irq, handle_edge_irq); + set_irq_flags(isa_irq, IRQF_VALID | IRQF_PROBE); + } + + set_irq_chained_handler(gpio_to_irq(VIPER_CPLD_GPIO), + viper_irq_handler); + set_irq_type(gpio_to_irq(VIPER_CPLD_GPIO), IRQ_TYPE_EDGE_BOTH); + +#ifndef CONFIG_SERIAL_PXA + /* + * 8250 doesn't support IRQ_TYPE being passed as part + * of the plat_serial8250_port structure... + */ + set_irq_type(gpio_to_irq(VIPER_UARTA_GPIO), IRQ_TYPE_EDGE_RISING); + set_irq_type(gpio_to_irq(VIPER_UARTB_GPIO), IRQ_TYPE_EDGE_RISING); +#endif +} + +/* Flat Panel */ +static struct pxafb_mode_info fb_mode_info[] = { + { + .pixclock = 157500, + + .xres = 320, + .yres = 240, + + .bpp = 16, + + .hsync_len = 63, + .left_margin = 7, + .right_margin = 13, + + .vsync_len = 20, + .upper_margin = 0, + .lower_margin = 0, + + .sync = 0, + }, +}; + +static struct pxafb_mach_info fb_info = { + .modes = fb_mode_info, + .num_modes = 1, + .lcd_conn = LCD_COLOR_TFT_16BPP | LCD_PCLK_EDGE_FALL, +}; + +static int viper_backlight_init(struct device *dev) +{ + int ret; + + /* GPIO9 and 10 control FB backlight. Initialise to off */ + ret = gpio_request(VIPER_BCKLIGHT_EN_GPIO, "Backlight"); + if (ret) + goto err_request_bckl; + + ret = gpio_request(VIPER_LCD_EN_GPIO, "LCD"); + if (ret) + goto err_request_lcd; + + ret = gpio_direction_output(VIPER_BCKLIGHT_EN_GPIO, 0); + if (ret) + goto err_dir; + + ret = gpio_direction_output(VIPER_LCD_EN_GPIO, 0); + if (ret) + goto err_dir; + + return 0; + +err_dir: + gpio_free(VIPER_LCD_EN_GPIO); +err_request_lcd: + gpio_free(VIPER_BCKLIGHT_EN_GPIO); +err_request_bckl: + dev_err(dev, "Failed to setup LCD GPIOs\n"); + + return ret; +} + +static int viper_backlight_notify(int brightness) +{ + gpio_set_value(VIPER_LCD_EN_GPIO, !!brightness); + gpio_set_value(VIPER_BCKLIGHT_EN_GPIO, !!brightness); + + return brightness; +} + +static void viper_backlight_exit(struct device *dev) +{ + gpio_free(VIPER_LCD_EN_GPIO); + gpio_free(VIPER_BCKLIGHT_EN_GPIO); +} + +static struct platform_pwm_backlight_data viper_backlight_data = { + .pwm_id = 0, + .max_brightness = 100, + .dft_brightness = 100, + .pwm_period_ns = 1000000, + .init = viper_backlight_init, + .notify = viper_backlight_notify, + .exit = viper_backlight_exit, +}; + +static struct platform_device viper_backlight_device = { + .name = "pwm-backlight", + .dev = { + .parent = &pxa25x_device_pwm0.dev, + .platform_data = &viper_backlight_data, + }, +}; + +/* Ethernet */ +static struct resource smc91x_resources[] = { + [0] = { + .name = "smc91x-regs", + .start = VIPER_ETH_PHYS + 0x300, + .end = VIPER_ETH_PHYS + 0x30f, + .flags = IORESOURCE_MEM, + }, + [1] = { + .start = gpio_to_irq(VIPER_ETH_GPIO), + .end = gpio_to_irq(VIPER_ETH_GPIO), + .flags = IORESOURCE_IRQ | IORESOURCE_IRQ_HIGHEDGE, + }, + [2] = { + .name = "smc91x-data32", + .start = VIPER_ETH_DATA_PHYS, + .end = VIPER_ETH_DATA_PHYS + 3, + .flags = IORESOURCE_MEM, + }, +}; + +static struct smc91x_platdata viper_smc91x_info = { + .flags = SMC91X_USE_16BIT | SMC91X_NOWAIT, + .leda = RPC_LED_100_10, + .ledb = RPC_LED_TX_RX, +}; + +static struct platform_device smc91x_device = { + .name = "smc91x", + .id = -1, + .num_resources = ARRAY_SIZE(smc91x_resources), + .resource = smc91x_resources, + .dev = { + .platform_data = &viper_smc91x_info, + }, +}; + +/* i2c */ +static struct i2c_gpio_platform_data i2c_bus_data = { + .sda_pin = VIPER_RTC_I2C_SDA_GPIO, + .scl_pin = VIPER_RTC_I2C_SCL_GPIO, + .udelay = 10, + .timeout = 100, +}; + +static struct platform_device i2c_bus_device = { + .name = "i2c-gpio", + .id = 1, /* pxa2xx-i2c is bus 0, so start at 1 */ + .dev = { + .platform_data = &i2c_bus_data, + } +}; + +static struct i2c_board_info __initdata viper_i2c_devices[] = { + { + I2C_BOARD_INFO("ds1338", 0x68), + }, +}; + +/* + * Serial configuration: + * You can either have the standard PXA ports driven by the PXA driver, + * or all the ports (PXA + 16850) driven by the 8250 driver. + * Choose your poison. + */ + +static struct resource viper_serial_resources[] = { +#ifndef CONFIG_SERIAL_PXA + { + .start = 0x40100000, + .end = 0x4010001f, + .flags = IORESOURCE_MEM, + }, + { + .start = 0x40200000, + .end = 0x4020001f, + .flags = IORESOURCE_MEM, + }, + { + .start = 0x40700000, + .end = 0x4070001f, + .flags = IORESOURCE_MEM, + }, + { + .start = VIPER_UARTA_PHYS, + .end = VIPER_UARTA_PHYS + 0xf, + .flags = IORESOURCE_MEM, + }, + { + .start = VIPER_UARTB_PHYS, + .end = VIPER_UARTB_PHYS + 0xf, + .flags = IORESOURCE_MEM, + }, +#else + { + 0, + }, +#endif +}; + +static struct plat_serial8250_port serial_platform_data[] = { +#ifndef CONFIG_SERIAL_PXA + /* Internal UARTs */ + { + .membase = (void *)&FFUART, + .mapbase = __PREG(FFUART), + .irq = IRQ_FFUART, + .uartclk = 921600 * 16, + .regshift = 2, + .flags = UPF_BOOT_AUTOCONF | UPF_SKIP_TEST, + .iotype = UPIO_MEM, + }, + { + .membase = (void *)&BTUART, + .mapbase = __PREG(BTUART), + .irq = IRQ_BTUART, + .uartclk = 921600 * 16, + .regshift = 2, + .flags = UPF_BOOT_AUTOCONF | UPF_SKIP_TEST, + .iotype = UPIO_MEM, + }, + { + .membase = (void *)&STUART, + .mapbase = __PREG(STUART), + .irq = IRQ_STUART, + .uartclk = 921600 * 16, + .regshift = 2, + .flags = UPF_BOOT_AUTOCONF | UPF_SKIP_TEST, + .iotype = UPIO_MEM, + }, + /* External UARTs */ + { + .mapbase = VIPER_UARTA_PHYS, + .irq = gpio_to_irq(VIPER_UARTA_GPIO), + .uartclk = 1843200, + .regshift = 1, + .iotype = UPIO_MEM, + .flags = UPF_BOOT_AUTOCONF | UPF_IOREMAP | + UPF_SKIP_TEST, + }, + { + .mapbase = VIPER_UARTB_PHYS, + .irq = gpio_to_irq(VIPER_UARTB_GPIO), + .uartclk = 1843200, + .regshift = 1, + .iotype = UPIO_MEM, + .flags = UPF_BOOT_AUTOCONF | UPF_IOREMAP | + UPF_SKIP_TEST, + }, +#endif + { }, +}; + +static struct platform_device serial_device = { + .name = "serial8250", + .id = 0, + .dev = { + .platform_data = serial_platform_data, + }, + .num_resources = ARRAY_SIZE(viper_serial_resources), + .resource = viper_serial_resources, +}; + +/* USB */ +static void isp116x_delay(struct device *dev, int delay) +{ + ndelay(delay); +} + +static struct resource isp116x_resources[] = { + [0] = { /* DATA */ + .start = VIPER_USB_PHYS + 0, + .end = VIPER_USB_PHYS + 1, + .flags = IORESOURCE_MEM, + }, + [1] = { /* ADDR */ + .start = VIPER_USB_PHYS + 2, + .end = VIPER_USB_PHYS + 3, + .flags = IORESOURCE_MEM, + }, + [2] = { + .start = gpio_to_irq(VIPER_USB_GPIO), + .end = gpio_to_irq(VIPER_USB_GPIO), + .flags = IORESOURCE_IRQ | IORESOURCE_IRQ_HIGHEDGE, + }, +}; + +/* (DataBusWidth16|AnalogOCEnable|DREQOutputPolarity|DownstreamPort15KRSel ) */ +static struct isp116x_platform_data isp116x_platform_data = { + /* Enable internal resistors on downstream ports */ + .sel15Kres = 1, + /* On-chip overcurrent protection */ + .oc_enable = 1, + /* INT output polarity */ + .int_act_high = 1, + /* INT edge or level triggered */ + .int_edge_triggered = 0, + + /* WAKEUP pin connected - NOT SUPPORTED */ + /* .remote_wakeup_connected = 0, */ + /* Wakeup by devices on usb bus enabled */ + .remote_wakeup_enable = 0, + .delay = isp116x_delay, +}; + +static struct platform_device isp116x_device = { + .name = "isp116x-hcd", + .id = -1, + .num_resources = ARRAY_SIZE(isp116x_resources), + .resource = isp116x_resources, + .dev = { + .platform_data = &isp116x_platform_data, + }, + +}; + +/* MTD */ +static struct resource mtd_resources[] = { + [0] = { /* RedBoot config + filesystem flash */ + .start = VIPER_FLASH_PHYS, + .end = VIPER_FLASH_PHYS + SZ_32M - 1, + .flags = IORESOURCE_MEM, + }, + [1] = { /* Boot flash */ + .start = VIPER_BOOT_PHYS, + .end = VIPER_BOOT_PHYS + SZ_1M - 1, + .flags = IORESOURCE_MEM, + }, + [2] = { /* + * SRAM size is actually 256KB, 8bits, with a sparse mapping + * (each byte is on a 16bit boundary). + */ + .start = _VIPER_SRAM_BASE, + .end = _VIPER_SRAM_BASE + SZ_512K - 1, + .flags = IORESOURCE_MEM, + }, +}; + +static struct mtd_partition viper_boot_flash_partition = { + .name = "RedBoot", + .size = SZ_1M, + .offset = 0, + .mask_flags = MTD_WRITEABLE, /* force R/O */ +}; + +static struct physmap_flash_data viper_flash_data[] = { + [0] = { + .width = 2, + .parts = NULL, + .nr_parts = 0, + }, + [1] = { + .width = 2, + .parts = &viper_boot_flash_partition, + .nr_parts = 1, + }, +}; + +static struct platform_device viper_mtd_devices[] = { + [0] = { + .name = "physmap-flash", + .id = 0, + .dev = { + .platform_data = &viper_flash_data[0], + }, + .resource = &mtd_resources[0], + .num_resources = 1, + }, + [1] = { + .name = "physmap-flash", + .id = 1, + .dev = { + .platform_data = &viper_flash_data[1], + }, + .resource = &mtd_resources[1], + .num_resources = 1, + }, +}; + +static struct platform_device *viper_devs[] __initdata = { + &smc91x_device, + &i2c_bus_device, + &serial_device, + &isp116x_device, + &viper_mtd_devices[0], + &viper_mtd_devices[1], + &viper_backlight_device, +}; + +static mfp_cfg_t viper_pin_config[] __initdata = { + /* Chip selects */ + GPIO15_nCS_1, + GPIO78_nCS_2, + GPIO79_nCS_3, + GPIO80_nCS_4, + GPIO33_nCS_5, + + /* FP Backlight */ + GPIO9_GPIO, /* VIPER_BCKLIGHT_EN_GPIO */ + GPIO10_GPIO, /* VIPER_LCD_EN_GPIO */ + GPIO16_PWM0_OUT, + + /* Ethernet PHY Ready */ + GPIO18_RDY, + + /* Serial shutdown */ + GPIO12_GPIO | MFP_LPM_DRIVE_HIGH, /* VIPER_UART_SHDN_GPIO */ + + /* Compact-Flash / PC104 */ + GPIO48_nPOE, + GPIO49_nPWE, + GPIO50_nPIOR, + GPIO51_nPIOW, + GPIO52_nPCE_1, + GPIO53_nPCE_2, + GPIO54_nPSKTSEL, + GPIO55_nPREG, + GPIO56_nPWAIT, + GPIO57_nIOIS16, + GPIO8_GPIO, /* VIPER_CF_RDY_GPIO */ + GPIO32_GPIO, /* VIPER_CF_CD_GPIO */ + GPIO82_GPIO, /* VIPER_CF_POWER_GPIO */ + + /* Integrated UPS control */ + GPIO20_GPIO, /* VIPER_UPS_GPIO */ + + /* Vcc regulator control */ + GPIO6_GPIO, /* VIPER_PSU_DATA_GPIO */ + GPIO11_GPIO, /* VIPER_PSU_CLK_GPIO */ + GPIO19_GPIO, /* VIPER_PSU_nCS_LD_GPIO */ + + /* i2c busses */ + GPIO26_GPIO, /* VIPER_TPM_I2C_SDA_GPIO */ + GPIO27_GPIO, /* VIPER_TPM_I2C_SCL_GPIO */ + GPIO83_GPIO, /* VIPER_RTC_I2C_SDA_GPIO */ + GPIO84_GPIO, /* VIPER_RTC_I2C_SCL_GPIO */ + + /* PC/104 Interrupt */ + GPIO1_GPIO | WAKEUP_ON_EDGE_RISE, /* VIPER_CPLD_GPIO */ +}; + +static unsigned long viper_tpm; + +static int __init viper_tpm_setup(char *str) +{ + strict_strtoul(str, 10, &viper_tpm); + return 1; +} + +__setup("tpm=", viper_tpm_setup); + +static void __init viper_tpm_init(void) +{ + struct platform_device *tpm_device; + struct i2c_gpio_platform_data i2c_tpm_data = { + .sda_pin = VIPER_TPM_I2C_SDA_GPIO, + .scl_pin = VIPER_TPM_I2C_SCL_GPIO, + .udelay = 10, + .timeout = 100, + }; + char *errstr; + + /* Allocate TPM i2c bus if requested */ + if (!viper_tpm) + return; + + tpm_device = platform_device_alloc("i2c-gpio", 2); + if (tpm_device) { + if (!platform_device_add_data(tpm_device, + &i2c_tpm_data, + sizeof(i2c_tpm_data))) { + if (platform_device_add(tpm_device)) { + errstr = "register TPM i2c bus"; + goto error_free_tpm; + } + } else { + errstr = "allocate TPM i2c bus data"; + goto error_free_tpm; + } + } else { + errstr = "allocate TPM i2c device"; + goto error_tpm; + } + + return; + +error_free_tpm: + kfree(tpm_device); +error_tpm: + pr_err("viper: Couldn't %s, giving up\n", errstr); +} + +static void __init viper_init_vcore_gpios(void) +{ + if (gpio_request(VIPER_PSU_DATA_GPIO, "PSU data")) + goto err_request_data; + + if (gpio_request(VIPER_PSU_CLK_GPIO, "PSU clock")) + goto err_request_clk; + + if (gpio_request(VIPER_PSU_nCS_LD_GPIO, "PSU cs")) + goto err_request_cs; + + if (gpio_direction_output(VIPER_PSU_DATA_GPIO, 0) || + gpio_direction_output(VIPER_PSU_CLK_GPIO, 0) || + gpio_direction_output(VIPER_PSU_nCS_LD_GPIO, 0)) + goto err_dir; + + /* c/should assume redboot set the correct level ??? */ + viper_set_core_cpu_voltage(get_clk_frequency_khz(0), 1); + + return; + +err_dir: + gpio_free(VIPER_PSU_nCS_LD_GPIO); +err_request_cs: + gpio_free(VIPER_PSU_CLK_GPIO); +err_request_clk: + gpio_free(VIPER_PSU_DATA_GPIO); +err_request_data: + pr_err("viper: Failed to setup vcore control GPIOs\n"); +} + +static void __init viper_init_serial_gpio(void) +{ + if (gpio_request(VIPER_UART_SHDN_GPIO, "UARTs shutdown")) + goto err_request; + + if (gpio_direction_output(VIPER_UART_SHDN_GPIO, 0)) + goto err_dir; + + return; + +err_dir: + gpio_free(VIPER_UART_SHDN_GPIO); +err_request: + pr_err("viper: Failed to setup UART shutdown GPIO\n"); +} + +#ifdef CONFIG_CPU_FREQ +static int viper_cpufreq_notifier(struct notifier_block *nb, + unsigned long val, void *data) +{ + struct cpufreq_freqs *freq = data; + + /* TODO: Adjust timings??? */ + + switch (val) { + case CPUFREQ_PRECHANGE: + if (freq->old < freq->new) { + /* we are getting faster so raise the voltage + * before we change freq */ + viper_set_core_cpu_voltage(freq->new, 0); + } + break; + case CPUFREQ_POSTCHANGE: + if (freq->old > freq->new) { + /* we are slowing down so drop the power + * after we change freq */ + viper_set_core_cpu_voltage(freq->new, 0); + } + break; + case CPUFREQ_RESUMECHANGE: + viper_set_core_cpu_voltage(freq->new, 0); + break; + default: + /* ignore */ + break; + } + + return 0; +} + +static struct notifier_block viper_cpufreq_notifier_block = { + .notifier_call = viper_cpufreq_notifier +}; + +static void __init viper_init_cpufreq(void) +{ + if (cpufreq_register_notifier(&viper_cpufreq_notifier_block, + CPUFREQ_TRANSITION_NOTIFIER)) + pr_err("viper: Failed to setup cpufreq notifier\n"); +} +#else +static inline void viper_init_cpufreq(void) {} +#endif + +static void viper_power_off(void) +{ + pr_notice("Shutting off UPS\n"); + gpio_set_value(VIPER_UPS_GPIO, 1); + /* Spin to death... */ + while (1); +} + +static void __init viper_init(void) +{ + u8 version; + + pm_power_off = viper_power_off; + + pxa2xx_mfp_config(ARRAY_AND_SIZE(viper_pin_config)); + + /* Wake-up serial console */ + viper_init_serial_gpio(); + + set_pxa_fb_info(&fb_info); + + /* v1 hardware cannot use the datacs line */ + version = viper_hw_version(); + if (version == 0) + smc91x_device.num_resources--; + + pxa_set_i2c_info(NULL); + platform_add_devices(viper_devs, ARRAY_SIZE(viper_devs)); + + viper_init_vcore_gpios(); + viper_init_cpufreq(); + + sysdev_driver_register(&cpu_sysdev_class, &viper_cpu_sysdev_driver); + + if (version) { + pr_info("viper: hardware v%di%d detected. " + "CPLD revision %d.\n", + VIPER_BOARD_VERSION(version), + VIPER_BOARD_ISSUE(version), + VIPER_CPLD_REVISION(version)); + system_rev = (VIPER_BOARD_VERSION(version) << 8) | + (VIPER_BOARD_ISSUE(version) << 4) | + VIPER_CPLD_REVISION(version); + } else { + pr_info("viper: No version register.\n"); + } + + i2c_register_board_info(1, ARRAY_AND_SIZE(viper_i2c_devices)); + + viper_tpm_init(); + pxa_set_ac97_info(NULL); +} + +static struct map_desc viper_io_desc[] __initdata = { + { + .virtual = VIPER_CPLD_BASE, + .pfn = __phys_to_pfn(VIPER_CPLD_PHYS), + .length = 0x00300000, + .type = MT_DEVICE, + }, + { + .virtual = VIPER_PC104IO_BASE, + .pfn = __phys_to_pfn(_PCMCIA1IO), + .length = 0x00800000, + .type = MT_DEVICE, + }, +}; + +static void __init viper_map_io(void) +{ + pxa_map_io(); + + iotable_init(viper_io_desc, ARRAY_SIZE(viper_io_desc)); + + PCFR |= PCFR_OPDE; +} + +MACHINE_START(VIPER, "Arcom/Eurotech VIPER SBC") + /* Maintainer: Marc Zyngier <maz@misterjones.org> */ + .phys_io = 0x40000000, + .io_pg_offst = (io_p2v(0x40000000) >> 18) & 0xfffc, + .boot_params = 0xa0000100, + .map_io = viper_map_io, + .init_irq = viper_init_irq, + .timer = &pxa_timer, + .init_machine = viper_init, +MACHINE_END diff --git a/arch/arm/mach-pxa/zylonite.c b/arch/arm/mach-pxa/zylonite.c index 4a0028087ea..81380443346 100644 --- a/arch/arm/mach-pxa/zylonite.c +++ b/arch/arm/mach-pxa/zylonite.c @@ -18,23 +18,30 @@ #include <linux/interrupt.h> #include <linux/init.h> #include <linux/platform_device.h> +#include <linux/pwm_backlight.h> +#include <linux/smc91x.h> #include <asm/mach-types.h> #include <asm/mach/arch.h> -#include <asm/hardware.h> -#include <asm/arch/gpio.h> -#include <asm/arch/pxafb.h> -#include <asm/arch/zylonite.h> -#include <asm/arch/mmc.h> -#include <asm/arch/pxa27x_keypad.h> - +#include <mach/hardware.h> +#include <mach/audio.h> +#include <mach/gpio.h> +#include <mach/pxafb.h> +#include <mach/zylonite.h> +#include <mach/mmc.h> +#include <mach/ohci.h> +#include <mach/pxa27x_keypad.h> +#include <mach/pxa3xx_nand.h> + +#include "devices.h" #include "generic.h" #define MAX_SLOTS 3 struct platform_mmc_slot zylonite_mmc_slot[MAX_SLOTS]; -int gpio_backlight; int gpio_eth_irq; +int gpio_debug_led1; +int gpio_debug_led2; int wm9713_irq; @@ -54,18 +61,72 @@ static struct resource smc91x_resources[] = { } }; +static struct smc91x_platdata zylonite_smc91x_info = { + .flags = SMC91X_USE_8BIT | SMC91X_USE_16BIT | + SMC91X_NOWAIT | SMC91X_USE_DMA, +}; + static struct platform_device smc91x_device = { .name = "smc91x", .id = 0, .num_resources = ARRAY_SIZE(smc91x_resources), .resource = smc91x_resources, + .dev = { + .platform_data = &zylonite_smc91x_info, + }, }; -#if defined(CONFIG_FB_PXA) || defined(CONFIG_FB_PXA_MODULE) -static void zylonite_backlight_power(int on) +#if defined(CONFIG_LEDS_GPIO) || defined(CONFIG_LEDS_GPIO_MODULE) +static struct gpio_led zylonite_debug_leds[] = { + [0] = { + .name = "zylonite:yellow:1", + .default_trigger = "heartbeat", + }, + [1] = { + .name = "zylonite:yellow:2", + .default_trigger = "default-on", + }, +}; + +static struct gpio_led_platform_data zylonite_debug_leds_info = { + .leds = zylonite_debug_leds, + .num_leds = ARRAY_SIZE(zylonite_debug_leds), +}; + +static struct platform_device zylonite_device_leds = { + .name = "leds-gpio", + .id = -1, + .dev = { + .platform_data = &zylonite_debug_leds_info, + } +}; + +static void __init zylonite_init_leds(void) { - gpio_set_value(gpio_backlight, on); + zylonite_debug_leds[0].gpio = gpio_debug_led1; + zylonite_debug_leds[1].gpio = gpio_debug_led2; + + platform_device_register(&zylonite_device_leds); } +#else +static inline void zylonite_init_leds(void) {} +#endif + +#if defined(CONFIG_FB_PXA) || defined(CONFIG_FB_PXA_MODULE) +static struct platform_pwm_backlight_data zylonite_backlight_data = { + .pwm_id = 3, + .max_brightness = 100, + .dft_brightness = 100, + .pwm_period_ns = 10000, +}; + +static struct platform_device zylonite_backlight_device = { + .name = "pwm-backlight", + .dev = { + .parent = &pxa27x_device_pwm1.dev, + .platform_data = &zylonite_backlight_data, + }, +}; static struct pxafb_mode_info toshiba_ltm035a776c_mode = { .pixclock = 110000, @@ -98,7 +159,6 @@ static struct pxafb_mode_info toshiba_ltm04c380k_mode = { static struct pxafb_mach_info zylonite_toshiba_lcd_info = { .num_modes = 1, .lcd_conn = LCD_COLOR_TFT_16BPP | LCD_PCLK_EDGE_FALL, - .pxafb_backlight_power = zylonite_backlight_power, }; static struct pxafb_mode_info sharp_ls037_modes[] = { @@ -134,13 +194,11 @@ static struct pxafb_mach_info zylonite_sharp_lcd_info = { .modes = sharp_ls037_modes, .num_modes = 2, .lcd_conn = LCD_COLOR_TFT_16BPP | LCD_PCLK_EDGE_FALL, - .pxafb_backlight_power = zylonite_backlight_power, }; static void __init zylonite_init_lcd(void) { - /* backlight GPIO: output, default on */ - gpio_direction_output(gpio_backlight, 1); + platform_device_register(&zylonite_backlight_device); if (lcd_id & 0x20) { set_pxa_fb_info(&zylonite_sharp_lcd_info); @@ -250,7 +308,7 @@ static void __init zylonite_init_mmc(void) static inline void zylonite_init_mmc(void) {} #endif -#if defined(CONFIG_KEYBOARD_PXA27x) || defined(CONFIG_KEYBOARD_PXA27x_MODULES) +#if defined(CONFIG_KEYBOARD_PXA27x) || defined(CONFIG_KEYBOARD_PXA27x_MODULE) static unsigned int zylonite_matrix_key_map[] = { /* KEY(row, col, key_code) */ KEY(0, 0, KEY_A), KEY(0, 1, KEY_B), KEY(0, 2, KEY_C), KEY(0, 5, KEY_D), @@ -315,6 +373,72 @@ static void __init zylonite_init_keypad(void) static inline void zylonite_init_keypad(void) {} #endif +#if defined(CONFIG_MTD_NAND_PXA3xx) || defined(CONFIG_MTD_NAND_PXA3xx_MODULE) +static struct mtd_partition zylonite_nand_partitions[] = { + [0] = { + .name = "Bootloader", + .offset = 0, + .size = 0x060000, + .mask_flags = MTD_WRITEABLE, /* force read-only */ + }, + [1] = { + .name = "Kernel", + .offset = 0x060000, + .size = 0x200000, + .mask_flags = MTD_WRITEABLE, /* force read-only */ + }, + [2] = { + .name = "Filesystem", + .offset = 0x0260000, + .size = 0x3000000, /* 48M - rootfs */ + }, + [3] = { + .name = "MassStorage", + .offset = 0x3260000, + .size = 0x3d40000, + }, + [4] = { + .name = "BBT", + .offset = 0x6FA0000, + .size = 0x80000, + .mask_flags = MTD_WRITEABLE, /* force read-only */ + }, + /* NOTE: we reserve some blocks at the end of the NAND flash for + * bad block management, and the max number of relocation blocks + * differs on different platforms. Please take care with it when + * defining the partition table. + */ +}; + +static struct pxa3xx_nand_platform_data zylonite_nand_info = { + .enable_arbiter = 1, + .parts = zylonite_nand_partitions, + .nr_parts = ARRAY_SIZE(zylonite_nand_partitions), +}; + +static void __init zylonite_init_nand(void) +{ + pxa3xx_set_nand_info(&zylonite_nand_info); +} +#else +static inline void zylonite_init_nand(void) {} +#endif /* CONFIG_MTD_NAND_PXA3xx || CONFIG_MTD_NAND_PXA3xx_MODULE */ + +#if defined(CONFIG_USB_OHCI_HCD) || defined(CONFIG_USB_OHCI_HCD_MODULE) +static struct pxaohci_platform_data zylonite_ohci_info = { + .port_mode = PMM_PERPORT_MODE, + .flags = ENABLE_PORT1 | ENABLE_PORT2 | + POWER_CONTROL_LOW | POWER_SENSE_LOW, +}; + +static void __init zylonite_init_ohci(void) +{ + pxa_set_ohci_info(&zylonite_ohci_info); +} +#else +static inline void zylonite_init_ohci(void) {} +#endif /* CONFIG_USB_OHCI_HCD || CONFIG_USB_OHCI_HCD_MODULE */ + static void __init zylonite_init(void) { /* board-processor specific initialization */ @@ -329,9 +453,13 @@ static void __init zylonite_init(void) smc91x_resources[1].end = gpio_to_irq(gpio_eth_irq); platform_device_register(&smc91x_device); + pxa_set_ac97_info(NULL); zylonite_init_lcd(); zylonite_init_mmc(); zylonite_init_keypad(); + zylonite_init_nand(); + zylonite_init_leds(); + zylonite_init_ohci(); } MACHINE_START(ZYLONITE, "PXA3xx Platform Development Kit (aka Zylonite)") diff --git a/arch/arm/mach-pxa/zylonite_pxa300.c b/arch/arm/mach-pxa/zylonite_pxa300.c index 324fb9daae2..46538885a58 100644 --- a/arch/arm/mach-pxa/zylonite_pxa300.c +++ b/arch/arm/mach-pxa/zylonite_pxa300.c @@ -16,10 +16,13 @@ #include <linux/module.h> #include <linux/kernel.h> #include <linux/init.h> +#include <linux/i2c.h> +#include <linux/i2c/pca953x.h> #include <asm/gpio.h> -#include <asm/arch/mfp-pxa300.h> -#include <asm/arch/zylonite.h> +#include <mach/mfp-pxa300.h> +#include <mach/i2c.h> +#include <mach/zylonite.h> #include "generic.h" @@ -50,6 +53,7 @@ static mfp_cfg_t common_mfp_cfg[] __initdata = { GPIO75_LCD_BIAS, GPIO76_LCD_VSYNC, GPIO127_LCD_CS_N, + GPIO20_PWM3_OUT, /* backlight */ /* BTUART */ GPIO111_UART2_RTS, @@ -69,6 +73,12 @@ static mfp_cfg_t common_mfp_cfg[] __initdata = { GPIO27_AC97_SDATA_OUT, GPIO28_AC97_SYNC, + /* SSP3 */ + GPIO91_SSP3_SCLK, + GPIO92_SSP3_FRM, + GPIO93_SSP3_TXD, + GPIO94_SSP3_RXD, + /* WM9713 IRQ */ GPIO26_GPIO, @@ -108,6 +118,14 @@ static mfp_cfg_t common_mfp_cfg[] __initdata = { GPIO12_MMC2_DAT3, GPIO13_MMC2_CLK, GPIO14_MMC2_CMD, + + /* USB Host */ + GPIO0_2_USBH_PEN, + GPIO1_2_USBH_PWR, + + /* Standard I2C */ + GPIO21_I2C_SCL, + GPIO22_I2C_SDA, }; static mfp_cfg_t pxa300_mfp_cfg[] __initdata = { @@ -191,6 +209,39 @@ static void __init zylonite_detect_lcd_panel(void) pxa3xx_mfp_write(lcd_detect_pins[i], mfpr_save[i]); } +#if defined(CONFIG_I2C) || defined(CONFIG_I2C_MODULE) +static struct pca953x_platform_data gpio_exp[] = { + [0] = { + .gpio_base = 128, + }, + [1] = { + .gpio_base = 144, + }, +}; + +static struct i2c_board_info zylonite_i2c_board_info[] = { + { + .type = "pca9539", + .addr = 0x74, + .platform_data = &gpio_exp[0], + .irq = IRQ_GPIO(18), + }, { + .type = "pca9539", + .addr = 0x75, + .platform_data = &gpio_exp[1], + .irq = IRQ_GPIO(19), + }, +}; + +static void __init zylonite_init_i2c(void) +{ + pxa_set_i2c_info(NULL); + i2c_register_board_info(0, ARRAY_AND_SIZE(zylonite_i2c_board_info)); +} +#else +static inline void zylonite_init_i2c(void) {} +#endif + void __init zylonite_pxa300_init(void) { if (cpu_is_pxa300() || cpu_is_pxa310()) { @@ -200,15 +251,14 @@ void __init zylonite_pxa300_init(void) /* detect LCD panel */ zylonite_detect_lcd_panel(); - /* GPIO pin assignment */ - gpio_backlight = mfp_to_gpio(MFP_PIN_GPIO20); - /* MMC card detect & write protect for controller 0 */ zylonite_mmc_slot[0].gpio_cd = EXT_GPIO(0); zylonite_mmc_slot[0].gpio_wp = EXT_GPIO(2); /* WM9713 IRQ */ wm9713_irq = mfp_to_gpio(MFP_PIN_GPIO26); + + zylonite_init_i2c(); } if (cpu_is_pxa300()) { @@ -224,4 +274,8 @@ void __init zylonite_pxa300_init(void) zylonite_mmc_slot[2].gpio_cd = EXT_GPIO(30); zylonite_mmc_slot[2].gpio_wp = EXT_GPIO(31); } + + /* GPIOs for Debug LEDs */ + gpio_debug_led1 = EXT_GPIO(25); + gpio_debug_led2 = EXT_GPIO(26); } diff --git a/arch/arm/mach-pxa/zylonite_pxa320.c b/arch/arm/mach-pxa/zylonite_pxa320.c index 193d07903b0..0f244744daa 100644 --- a/arch/arm/mach-pxa/zylonite_pxa320.c +++ b/arch/arm/mach-pxa/zylonite_pxa320.c @@ -17,9 +17,9 @@ #include <linux/kernel.h> #include <linux/init.h> -#include <asm/arch/gpio.h> -#include <asm/arch/mfp-pxa320.h> -#include <asm/arch/zylonite.h> +#include <mach/gpio.h> +#include <mach/mfp-pxa320.h> +#include <mach/zylonite.h> #include "generic.h" @@ -49,6 +49,7 @@ static mfp_cfg_t mfp_cfg[] __initdata = { GPIO15_2_LCD_LCLK, GPIO16_2_LCD_PCLK, GPIO17_2_LCD_BIAS, + GPIO14_PWM3_OUT, /* backlight */ /* FFUART */ GPIO41_UART1_RXD | MFP_LPM_EDGE_FALL, @@ -68,6 +69,12 @@ static mfp_cfg_t mfp_cfg[] __initdata = { GPIO39_AC97_BITCLK, GPIO40_AC97_nACRESET, + /* SSP3 */ + GPIO89_SSP3_SCLK, + GPIO90_SSP3_FRM, + GPIO91_SSP3_TXD, + GPIO92_SSP3_RXD, + /* WM9713 IRQ */ GPIO15_GPIO, @@ -115,6 +122,14 @@ static mfp_cfg_t mfp_cfg[] __initdata = { GPIO27_MMC2_DAT3, GPIO28_MMC2_CLK, GPIO29_MMC2_CMD, + + /* USB Host */ + GPIO2_2_USBH_PEN, + GPIO3_2_USBH_PWR, + + /* Debug LEDs */ + GPIO1_2_GPIO | MFP_LPM_DRIVE_HIGH, + GPIO4_2_GPIO | MFP_LPM_DRIVE_HIGH, }; #define NUM_LCD_DETECT_PINS 7 @@ -187,8 +202,9 @@ void __init zylonite_pxa320_init(void) zylonite_detect_lcd_panel(); /* GPIO pin assignment */ - gpio_backlight = mfp_to_gpio(MFP_PIN_GPIO14); gpio_eth_irq = mfp_to_gpio(MFP_PIN_GPIO9); + gpio_debug_led1 = mfp_to_gpio(MFP_PIN_GPIO1_2); + gpio_debug_led2 = mfp_to_gpio(MFP_PIN_GPIO4_2); /* MMC card detect & write protect for controller 0 */ zylonite_mmc_slot[0].gpio_cd = mfp_to_gpio(MFP_PIN_GPIO1); |