diff options
Diffstat (limited to 'arch/arm')
49 files changed, 5680 insertions, 264 deletions
diff --git a/arch/arm/Kconfig b/arch/arm/Kconfig index 0d8fac3b037..e55bbd32dca 100644 --- a/arch/arm/Kconfig +++ b/arch/arm/Kconfig @@ -114,9 +114,6 @@ config GENERIC_CALIBRATE_DELAY bool default y -config GENERIC_BUST_SPINLOCK - bool - config ARCH_MAY_HAVE_PC_FDC bool @@ -247,6 +244,15 @@ config ARCH_IMX help Support for Motorola's i.MX family of processors (MX1, MXL). +config ARCH_IOP13XX + bool "IOP13xx-based" + depends on MMU + select PLAT_IOP + select PCI + select ARCH_SUPPORTS_MSI + help + Support for Intel's IOP13XX (XScale) family of processors. + config ARCH_IOP32X bool "IOP32x-based" depends on MMU @@ -264,22 +270,12 @@ config ARCH_IOP33X help Support for Intel's IOP33X (XScale) family of processors. -config ARCH_IOP13XX - bool "IOP13xx-based" - depends on MMU - select PLAT_IOP - select PCI - select ARCH_SUPPORTS_MSI - help - Support for Intel's IOP13XX (XScale) family of processors. - -config ARCH_IXP4XX - bool "IXP4xx-based" +config ARCH_IXP23XX + bool "IXP23XX-based" depends on MMU - select GENERIC_TIME - select GENERIC_CLOCKEVENTS + select PCI help - Support for Intel's IXP4XX (XScale) family of processors. + Support for Intel's IXP23xx (XScale) family of processors. config ARCH_IXP2000 bool "IXP2400/2800-based" @@ -288,12 +284,13 @@ config ARCH_IXP2000 help Support for Intel's IXP2400/2800 (XScale) family of processors. -config ARCH_IXP23XX - bool "IXP23XX-based" +config ARCH_IXP4XX + bool "IXP4xx-based" depends on MMU - select PCI + select GENERIC_TIME + select GENERIC_CLOCKEVENTS help - Support for Intel's IXP23xx (XScale) family of processors. + Support for Intel's IXP4XX (XScale) family of processors. config ARCH_L7200 bool "LinkUp-L7200" @@ -308,6 +305,12 @@ config ARCH_L7200 If you have any questions or comments about the Linux kernel port to this board, send e-mail to <sjhill@cotw.com>. +config ARCH_KS8695 + bool "Micrel/Kendin KS8695" + help + Support for Micrel/Kendin KS8695 "Centaur" (ARM922T) based + System-on-Chip devices. + config ARCH_NS9XXX bool "NetSilicon NS9xxx" help @@ -376,6 +379,13 @@ config ARCH_LH7A40X core with a wide array of integrated devices for hand-held and low-power applications. +config ARCH_DAVINCI + bool "TI DaVinci" + select GENERIC_TIME + select GENERIC_CLOCKEVENTS + help + Support for TI's DaVinci platform. + config ARCH_OMAP bool "TI OMAP" select GENERIC_GPIO @@ -444,6 +454,10 @@ source "arch/arm/mach-netx/Kconfig" source "arch/arm/mach-ns9xxx/Kconfig" +source "arch/arm/mach-davinci/Kconfig" + +source "arch/arm/mach-ks8695/Kconfig" + # Definitions to make life easier config ARCH_ACORN bool @@ -504,7 +518,7 @@ config ISA_DMA_API bool config PCI - bool "PCI support" if ARCH_INTEGRATOR_AP || ARCH_VERSATILE_PB || ARCH_IXP4XX + bool "PCI support" if ARCH_INTEGRATOR_AP || ARCH_VERSATILE_PB || ARCH_IXP4XX || ARCH_KS8695 help Find out whether you have a PCI motherboard. PCI is the name of a bus system, i.e. the way the CPU talks to the other stuff inside @@ -673,7 +687,8 @@ config LEDS ARCH_LUBBOCK || MACH_MAINSTONE || ARCH_NETWINDER || \ ARCH_OMAP || ARCH_P720T || ARCH_PXA_IDP || \ ARCH_SA1100 || ARCH_SHARK || ARCH_VERSATILE || \ - ARCH_AT91 || MACH_TRIZEPS4 + ARCH_AT91 || MACH_TRIZEPS4 || ARCH_DAVINCI || \ + ARCH_KS8695 help If you say Y here, the LEDs on your machine will be used to provide useful information about your current system status. diff --git a/arch/arm/Makefile b/arch/arm/Makefile index 00ea4305ad5..cbd5010d3bc 100644 --- a/arch/arm/Makefile +++ b/arch/arm/Makefile @@ -135,6 +135,8 @@ endif machine-$(CONFIG_ARCH_NETX) := netx machine-$(CONFIG_ARCH_NS9XXX) := ns9xxx textofs-$(CONFIG_ARCH_NS9XXX) := 0x00108000 + machine-$(CONFIG_ARCH_DAVINCI) := davinci + machine-$(CONFIG_ARCH_KS8695) := ks8695 ifeq ($(CONFIG_ARCH_EBSA110),y) # This is what happens if you forget the IOCS16 line. diff --git a/arch/arm/configs/at91sam9rlek_defconfig b/arch/arm/configs/at91sam9rlek_defconfig new file mode 100644 index 00000000000..fbe8b304934 --- /dev/null +++ b/arch/arm/configs/at91sam9rlek_defconfig @@ -0,0 +1,957 @@ +# +# Automatically generated make config: don't edit +# Linux kernel version: 2.6.21 +# Mon May 7 16:30:40 2007 +# +CONFIG_ARM=y +CONFIG_SYS_SUPPORTS_APM_EMULATION=y +CONFIG_GENERIC_GPIO=y +# CONFIG_GENERIC_TIME is not set +CONFIG_MMU=y +# CONFIG_NO_IOPORT is not set +CONFIG_GENERIC_HARDIRQS=y +CONFIG_TRACE_IRQFLAGS_SUPPORT=y +CONFIG_HARDIRQS_SW_RESEND=y +CONFIG_GENERIC_IRQ_PROBE=y +CONFIG_RWSEM_GENERIC_SPINLOCK=y +# CONFIG_ARCH_HAS_ILOG2_U32 is not set +# CONFIG_ARCH_HAS_ILOG2_U64 is not set +CONFIG_GENERIC_HWEIGHT=y +CONFIG_GENERIC_CALIBRATE_DELAY=y +CONFIG_ZONE_DMA=y +CONFIG_VECTORS_BASE=0xffff0000 +CONFIG_DEFCONFIG_LIST="/lib/modules/$UNAME_RELEASE/.config" + +# +# Code maturity level options +# +CONFIG_EXPERIMENTAL=y +CONFIG_BROKEN_ON_SMP=y +CONFIG_INIT_ENV_ARG_LIMIT=32 + +# +# General setup +# +CONFIG_LOCALVERSION="" +# CONFIG_LOCALVERSION_AUTO is not set +# CONFIG_SWAP is not set +CONFIG_SYSVIPC=y +# CONFIG_IPC_NS is not set +CONFIG_SYSVIPC_SYSCTL=y +# CONFIG_POSIX_MQUEUE is not set +# CONFIG_BSD_PROCESS_ACCT is not set +# CONFIG_TASKSTATS is not set +# CONFIG_UTS_NS is not set +# CONFIG_AUDIT is not set +# CONFIG_IKCONFIG is not set +CONFIG_SYSFS_DEPRECATED=y +# CONFIG_RELAY is not set +CONFIG_BLK_DEV_INITRD=y +CONFIG_INITRAMFS_SOURCE="" +CONFIG_CC_OPTIMIZE_FOR_SIZE=y +CONFIG_SYSCTL=y +# CONFIG_EMBEDDED is not set +CONFIG_UID16=y +CONFIG_SYSCTL_SYSCALL=y +CONFIG_KALLSYMS=y +# CONFIG_KALLSYMS_ALL is not set +# CONFIG_KALLSYMS_EXTRA_PASS is not set +CONFIG_HOTPLUG=y +CONFIG_PRINTK=y +CONFIG_BUG=y +CONFIG_ELF_CORE=y +CONFIG_BASE_FULL=y +CONFIG_FUTEX=y +CONFIG_EPOLL=y +CONFIG_SHMEM=y +CONFIG_SLAB=y +CONFIG_VM_EVENT_COUNTERS=y +CONFIG_RT_MUTEXES=y +# CONFIG_TINY_SHMEM is not set +CONFIG_BASE_SMALL=0 +# CONFIG_SLOB is not set + +# +# Loadable module support +# +CONFIG_MODULES=y +CONFIG_MODULE_UNLOAD=y +# CONFIG_MODULE_FORCE_UNLOAD is not set +# CONFIG_MODVERSIONS is not set +# CONFIG_MODULE_SRCVERSION_ALL is not set +CONFIG_KMOD=y + +# +# Block layer +# +CONFIG_BLOCK=y +# CONFIG_LBD is not set +# CONFIG_BLK_DEV_IO_TRACE is not set +# CONFIG_LSF is not set + +# +# IO Schedulers +# +CONFIG_IOSCHED_NOOP=y +CONFIG_IOSCHED_AS=y +# CONFIG_IOSCHED_DEADLINE is not set +# CONFIG_IOSCHED_CFQ is not set +CONFIG_DEFAULT_AS=y +# CONFIG_DEFAULT_DEADLINE is not set +# CONFIG_DEFAULT_CFQ is not set +# CONFIG_DEFAULT_NOOP is not set +CONFIG_DEFAULT_IOSCHED="anticipatory" + +# +# System Type +# +# CONFIG_ARCH_AAEC2000 is not set +# CONFIG_ARCH_INTEGRATOR is not set +# CONFIG_ARCH_REALVIEW is not set +# CONFIG_ARCH_VERSATILE is not set +CONFIG_ARCH_AT91=y +# CONFIG_ARCH_CLPS7500 is not set +# CONFIG_ARCH_CLPS711X is not set +# CONFIG_ARCH_CO285 is not set +# CONFIG_ARCH_EBSA110 is not set +# CONFIG_ARCH_EP93XX is not set +# CONFIG_ARCH_FOOTBRIDGE is not set +# CONFIG_ARCH_NETX is not set +# CONFIG_ARCH_H720X is not set +# CONFIG_ARCH_IMX is not set +# CONFIG_ARCH_IOP32X is not set +# CONFIG_ARCH_IOP33X is not set +# CONFIG_ARCH_IOP13XX is not set +# CONFIG_ARCH_IXP4XX is not set +# CONFIG_ARCH_IXP2000 is not set +# CONFIG_ARCH_IXP23XX is not set +# CONFIG_ARCH_L7200 is not set +# CONFIG_ARCH_NS9XXX is not set +# CONFIG_ARCH_PNX4008 is not set +# CONFIG_ARCH_PXA is not set +# CONFIG_ARCH_RPC is not set +# CONFIG_ARCH_SA1100 is not set +# CONFIG_ARCH_S3C2410 is not set +# CONFIG_ARCH_SHARK is not set +# CONFIG_ARCH_LH7A40X is not set +# CONFIG_ARCH_OMAP is not set + +# +# Atmel AT91 System-on-Chip +# +# CONFIG_ARCH_AT91RM9200 is not set +# CONFIG_ARCH_AT91SAM9260 is not set +# CONFIG_ARCH_AT91SAM9261 is not set +# CONFIG_ARCH_AT91SAM9263 is not set +CONFIG_ARCH_AT91SAM9RL=y + +# +# AT91SAM9RL Board Type +# +CONFIG_MACH_AT91SAM9RLEK=y + +# +# AT91 Board Options +# + +# +# AT91 Feature Selections +# +# CONFIG_AT91_PROGRAMMABLE_CLOCKS is not set + +# +# Processor Type +# +CONFIG_CPU_32=y +CONFIG_CPU_ARM926T=y +CONFIG_CPU_32v5=y +CONFIG_CPU_ABRT_EV5TJ=y +CONFIG_CPU_CACHE_VIVT=y +CONFIG_CPU_COPY_V4WB=y +CONFIG_CPU_TLB_V4WBI=y +CONFIG_CPU_CP15=y +CONFIG_CPU_CP15_MMU=y + +# +# Processor Features +# +# CONFIG_ARM_THUMB is not set +# CONFIG_CPU_ICACHE_DISABLE is not set +# CONFIG_CPU_DCACHE_DISABLE is not set +# CONFIG_CPU_DCACHE_WRITETHROUGH is not set +# CONFIG_CPU_CACHE_ROUND_ROBIN is not set +# CONFIG_OUTER_CACHE is not set + +# +# Bus support +# + +# +# PCCARD (PCMCIA/CardBus) support +# +# CONFIG_PCCARD is not set + +# +# Kernel Features +# +# CONFIG_PREEMPT is not set +# CONFIG_NO_IDLE_HZ is not set +CONFIG_HZ=100 +# CONFIG_AEABI is not set +# CONFIG_ARCH_DISCONTIGMEM_ENABLE is not set +CONFIG_SELECT_MEMORY_MODEL=y +CONFIG_FLATMEM_MANUAL=y +# CONFIG_DISCONTIGMEM_MANUAL is not set +# CONFIG_SPARSEMEM_MANUAL is not set +CONFIG_FLATMEM=y +CONFIG_FLAT_NODE_MEM_MAP=y +# CONFIG_SPARSEMEM_STATIC is not set +CONFIG_SPLIT_PTLOCK_CPUS=4096 +# CONFIG_RESOURCES_64BIT is not set +CONFIG_ZONE_DMA_FLAG=1 +# CONFIG_LEDS is not set +CONFIG_ALIGNMENT_TRAP=y + +# +# Boot options +# +CONFIG_ZBOOT_ROM_TEXT=0x0 +CONFIG_ZBOOT_ROM_BSS=0x0 +CONFIG_CMDLINE="mem=64M console=ttyS0,115200 initrd=0x21100000,17105363 root=/dev/ram0 rw" +# CONFIG_XIP_KERNEL is not set +# CONFIG_KEXEC is not set + +# +# Floating point emulation +# + +# +# At least one emulation must be selected +# +CONFIG_FPE_NWFPE=y +# CONFIG_FPE_NWFPE_XP is not set +# CONFIG_FPE_FASTFPE is not set +# CONFIG_VFP is not set + +# +# Userspace binary formats +# +CONFIG_BINFMT_ELF=y +# CONFIG_BINFMT_AOUT is not set +# CONFIG_BINFMT_MISC is not set +# CONFIG_ARTHUR is not set + +# +# Power management options +# +# CONFIG_PM is not set + +# +# Networking +# +CONFIG_NET=y + +# +# Networking options +# +# CONFIG_NETDEBUG is not set +# CONFIG_PACKET is not set +CONFIG_UNIX=y +# CONFIG_NET_KEY is not set +# CONFIG_INET is not set +# CONFIG_NETWORK_SECMARK is not set +# CONFIG_NETFILTER is not set +# CONFIG_ATM is not set +# CONFIG_BRIDGE is not set +# CONFIG_VLAN_8021Q is not set +# CONFIG_DECNET is not set +# CONFIG_LLC2 is not set +# CONFIG_IPX is not set +# CONFIG_ATALK is not set +# CONFIG_X25 is not set +# CONFIG_LAPB is not set +# CONFIG_WAN_ROUTER is not set + +# +# QoS and/or fair queueing +# +# CONFIG_NET_SCHED is not set + +# +# Network testing +# +# CONFIG_NET_PKTGEN is not set +# CONFIG_HAMRADIO is not set +# CONFIG_IRDA is not set +# CONFIG_BT is not set +# CONFIG_IEEE80211 is not set + +# +# Device Drivers +# + +# +# Generic Driver Options +# +CONFIG_STANDALONE=y +CONFIG_PREVENT_FIRMWARE_BUILD=y +# CONFIG_FW_LOADER is not set +# CONFIG_DEBUG_DRIVER is not set +# CONFIG_DEBUG_DEVRES is not set +# CONFIG_SYS_HYPERVISOR is not set + +# +# Connector - unified userspace <-> kernelspace linker +# +# CONFIG_CONNECTOR is not set + +# +# Memory Technology Devices (MTD) +# +CONFIG_MTD=y +# CONFIG_MTD_DEBUG is not set +CONFIG_MTD_CONCAT=y +CONFIG_MTD_PARTITIONS=y +# CONFIG_MTD_REDBOOT_PARTS is not set +CONFIG_MTD_CMDLINE_PARTS=y +# CONFIG_MTD_AFS_PARTS is not set + +# +# User Modules And Translation Layers +# +CONFIG_MTD_CHAR=y +CONFIG_MTD_BLKDEVS=y +CONFIG_MTD_BLOCK=y +# CONFIG_FTL is not set +# CONFIG_NFTL is not set +# CONFIG_INFTL is not set +# CONFIG_RFD_FTL is not set +# CONFIG_SSFDC is not set + +# +# RAM/ROM/Flash chip drivers +# +# CONFIG_MTD_CFI is not set +# CONFIG_MTD_JEDECPROBE is not set +CONFIG_MTD_MAP_BANK_WIDTH_1=y +CONFIG_MTD_MAP_BANK_WIDTH_2=y +CONFIG_MTD_MAP_BANK_WIDTH_4=y +# CONFIG_MTD_MAP_BANK_WIDTH_8 is not set +# CONFIG_MTD_MAP_BANK_WIDTH_16 is not set +# CONFIG_MTD_MAP_BANK_WIDTH_32 is not set +CONFIG_MTD_CFI_I1=y +CONFIG_MTD_CFI_I2=y +# CONFIG_MTD_CFI_I4 is not set +# CONFIG_MTD_CFI_I8 is not set +# CONFIG_MTD_RAM is not set +# CONFIG_MTD_ROM is not set +# CONFIG_MTD_ABSENT is not set +# CONFIG_MTD_OBSOLETE_CHIPS is not set + +# +# Mapping drivers for chip access +# +# CONFIG_MTD_COMPLEX_MAPPINGS is not set +# CONFIG_MTD_PLATRAM is not set + +# +# Self-contained MTD device drivers +# +CONFIG_MTD_DATAFLASH=y +# CONFIG_MTD_M25P80 is not set +# CONFIG_MTD_SLRAM is not set +# CONFIG_MTD_PHRAM is not set +# CONFIG_MTD_MTDRAM is not set +# CONFIG_MTD_BLOCK2MTD is not set + +# +# Disk-On-Chip Device Drivers +# +# CONFIG_MTD_DOC2000 is not set +# CONFIG_MTD_DOC2001 is not set +# CONFIG_MTD_DOC2001PLUS is not set + +# +# NAND Flash Device Drivers +# +CONFIG_MTD_NAND=y +# CONFIG_MTD_NAND_VERIFY_WRITE is not set +# CONFIG_MTD_NAND_ECC_SMC is not set +CONFIG_MTD_NAND_IDS=y +# CONFIG_MTD_NAND_DISKONCHIP is not set +CONFIG_MTD_NAND_AT91=y +# CONFIG_MTD_NAND_NANDSIM is not set + +# +# OneNAND Flash Device Drivers +# +# CONFIG_MTD_ONENAND is not set + +# +# Parallel port support +# +# CONFIG_PARPORT is not set + +# +# Plug and Play support +# +# CONFIG_PNPACPI is not set + +# +# Block devices +# +# CONFIG_BLK_DEV_COW_COMMON is not set +CONFIG_BLK_DEV_LOOP=y +# CONFIG_BLK_DEV_CRYPTOLOOP is not set +# CONFIG_BLK_DEV_NBD is not set +CONFIG_BLK_DEV_RAM=y +CONFIG_BLK_DEV_RAM_COUNT=4 +CONFIG_BLK_DEV_RAM_SIZE=24576 +CONFIG_BLK_DEV_RAM_BLOCKSIZE=1024 +# CONFIG_CDROM_PKTCDVD is not set +# CONFIG_ATA_OVER_ETH is not set + +# +# SCSI device support +# +# CONFIG_RAID_ATTRS is not set +CONFIG_SCSI=y +# CONFIG_SCSI_TGT is not set +# CONFIG_SCSI_NETLINK is not set +CONFIG_SCSI_PROC_FS=y + +# +# SCSI support type (disk, tape, CD-ROM) +# +CONFIG_BLK_DEV_SD=y +# CONFIG_CHR_DEV_ST is not set +# CONFIG_CHR_DEV_OSST is not set +# CONFIG_BLK_DEV_SR is not set +# CONFIG_CHR_DEV_SG is not set +# CONFIG_CHR_DEV_SCH is not set + +# +# Some SCSI devices (e.g. CD jukebox) support multiple LUNs +# +CONFIG_SCSI_MULTI_LUN=y +# CONFIG_SCSI_CONSTANTS is not set +# CONFIG_SCSI_LOGGING is not set +# CONFIG_SCSI_SCAN_ASYNC is not set + +# +# SCSI Transports +# +# CONFIG_SCSI_SPI_ATTRS is not set +# CONFIG_SCSI_FC_ATTRS is not set +# CONFIG_SCSI_ISCSI_ATTRS is not set +# CONFIG_SCSI_SAS_ATTRS is not set +# CONFIG_SCSI_SAS_LIBSAS is not set + +# +# SCSI low-level drivers +# +# CONFIG_SCSI_DEBUG is not set + +# +# Serial ATA (prod) and Parallel ATA (experimental) drivers +# +# CONFIG_ATA is not set + +# +# Multi-device support (RAID and LVM) +# +# CONFIG_MD is not set + +# +# Fusion MPT device support +# +# CONFIG_FUSION is not set + +# +# IEEE 1394 (FireWire) support +# + +# +# I2O device support +# + +# +# Network device support +# +# CONFIG_NETDEVICES is not set +# CONFIG_NETPOLL is not set +# CONFIG_NET_POLL_CONTROLLER is not set + +# +# ISDN subsystem +# +# CONFIG_ISDN is not set + +# +# Input device support +# +CONFIG_INPUT=y +# CONFIG_INPUT_FF_MEMLESS is not set + +# +# Userland interfaces +# +CONFIG_INPUT_MOUSEDEV=y +# CONFIG_INPUT_MOUSEDEV_PSAUX is not set +CONFIG_INPUT_MOUSEDEV_SCREEN_X=320 +CONFIG_INPUT_MOUSEDEV_SCREEN_Y=240 +# CONFIG_INPUT_JOYDEV is not set +# CONFIG_INPUT_TSDEV is not set +CONFIG_INPUT_EVDEV=y +# CONFIG_INPUT_EVBUG is not set + +# +# Input Device Drivers +# +# CONFIG_INPUT_KEYBOARD is not set +# CONFIG_INPUT_MOUSE is not set +# CONFIG_INPUT_JOYSTICK is not set +CONFIG_INPUT_TOUCHSCREEN=y +# CONFIG_TOUCHSCREEN_ADS7846 is not set +# CONFIG_TOUCHSCREEN_GUNZE is not set +# CONFIG_TOUCHSCREEN_ELO is not set +# CONFIG_TOUCHSCREEN_MTOUCH is not set +# CONFIG_TOUCHSCREEN_MK712 is not set +# CONFIG_TOUCHSCREEN_PENMOUNT is not set +# CONFIG_TOUCHSCREEN_TOUCHRIGHT is not set +# CONFIG_TOUCHSCREEN_TOUCHWIN is not set +# CONFIG_TOUCHSCREEN_UCB1400 is not set +# CONFIG_INPUT_MISC is not set + +# +# Hardware I/O ports +# +# CONFIG_SERIO is not set +# CONFIG_GAMEPORT is not set + +# +# Character devices +# +CONFIG_VT=y +CONFIG_VT_CONSOLE=y +CONFIG_HW_CONSOLE=y +# CONFIG_VT_HW_CONSOLE_BINDING is not set +# CONFIG_SERIAL_NONSTANDARD is not set + +# +# Serial drivers +# +# CONFIG_SERIAL_8250 is not set + +# +# Non-8250 serial port support +# +CONFIG_SERIAL_ATMEL=y +CONFIG_SERIAL_ATMEL_CONSOLE=y +# CONFIG_SERIAL_ATMEL_TTYAT is not set +CONFIG_SERIAL_CORE=y +CONFIG_SERIAL_CORE_CONSOLE=y +CONFIG_UNIX98_PTYS=y +CONFIG_LEGACY_PTYS=y +CONFIG_LEGACY_PTY_COUNT=256 + +# +# IPMI +# +# CONFIG_IPMI_HANDLER is not set + +# +# Watchdog Cards +# +CONFIG_WATCHDOG=y +CONFIG_WATCHDOG_NOWAYOUT=y + +# +# Watchdog Device Drivers +# +# CONFIG_SOFT_WATCHDOG is not set +CONFIG_HW_RANDOM=y +# CONFIG_NVRAM is not set +# CONFIG_DTLK is not set +# CONFIG_R3964 is not set +# CONFIG_RAW_DRIVER is not set + +# +# TPM devices +# +# CONFIG_TCG_TPM is not set + +# +# I2C support +# +# CONFIG_I2C is not set + +# +# SPI support +# +CONFIG_SPI=y +# CONFIG_SPI_DEBUG is not set +CONFIG_SPI_MASTER=y + +# +# SPI Master Controller Drivers +# +CONFIG_SPI_ATMEL=y +# CONFIG_SPI_BITBANG is not set + +# +# SPI Protocol Masters +# +# CONFIG_SPI_AT25 is not set + +# +# Dallas's 1-wire bus +# +# CONFIG_W1 is not set + +# +# Hardware Monitoring support +# +# CONFIG_HWMON is not set +# CONFIG_HWMON_VID is not set + +# +# Misc devices +# + +# +# Multifunction device drivers +# +# CONFIG_MFD_SM501 is not set + +# +# LED devices +# +# CONFIG_NEW_LEDS is not set + +# +# LED drivers +# + +# +# LED Triggers +# + +# +# Multimedia devices +# +# CONFIG_VIDEO_DEV is not set + +# +# Digital Video Broadcasting Devices +# + +# +# Graphics support +# +# CONFIG_BACKLIGHT_LCD_SUPPORT is not set +CONFIG_FB=y +# CONFIG_FIRMWARE_EDID is not set +# CONFIG_FB_DDC is not set +CONFIG_FB_CFB_FILLRECT=y +CONFIG_FB_CFB_COPYAREA=y +CONFIG_FB_CFB_IMAGEBLIT=y +# CONFIG_FB_SVGALIB is not set +# CONFIG_FB_MACMODES is not set +# CONFIG_FB_BACKLIGHT is not set +# CONFIG_FB_MODE_HELPERS is not set +# CONFIG_FB_TILEBLITTING is not set + +# +# Frame buffer hardware drivers +# +# CONFIG_FB_S1D13XXX is not set +CONFIG_FB_ATMEL=y +# CONFIG_FB_VIRTUAL is not set + +# +# Console display driver support +# +# CONFIG_VGA_CONSOLE is not set +CONFIG_DUMMY_CONSOLE=y +# CONFIG_FRAMEBUFFER_CONSOLE is not set + +# +# Logo configuration +# +# CONFIG_LOGO is not set + +# +# Sound +# +CONFIG_SOUND=y + +# +# Advanced Linux Sound Architecture +# +CONFIG_SND=y +CONFIG_SND_TIMER=y +CONFIG_SND_PCM=y +CONFIG_SND_SEQUENCER=y +CONFIG_SND_SEQ_DUMMY=y +CONFIG_SND_OSSEMUL=y +CONFIG_SND_MIXER_OSS=y +CONFIG_SND_PCM_OSS=y +CONFIG_SND_PCM_OSS_PLUGINS=y +CONFIG_SND_SEQUENCER_OSS=y +# CONFIG_SND_DYNAMIC_MINORS is not set +CONFIG_SND_SUPPORT_OLD_API=y +CONFIG_SND_VERBOSE_PROCFS=y +CONFIG_SND_VERBOSE_PRINTK=y +CONFIG_SND_DEBUG=y +CONFIG_SND_DEBUG_DETECT=y +# CONFIG_SND_PCM_XRUN_DEBUG is not set + +# +# Generic devices +# +# CONFIG_SND_DUMMY is not set +# CONFIG_SND_VIRMIDI is not set +# CONFIG_SND_MTPAV is not set +# CONFIG_SND_SERIAL_U16550 is not set +# CONFIG_SND_MPU401 is not set + +# +# ALSA ARM devices +# + +# +# SoC audio support +# +# CONFIG_SND_SOC is not set + +# +# Open Sound System +# +# CONFIG_SOUND_PRIME is not set + +# +# HID Devices +# +CONFIG_HID=y +# CONFIG_HID_DEBUG is not set + +# +# USB support +# +CONFIG_USB_ARCH_HAS_HCD=y +CONFIG_USB_ARCH_HAS_OHCI=y +# CONFIG_USB_ARCH_HAS_EHCI is not set +# CONFIG_USB is not set + +# +# NOTE: USB_STORAGE enables SCSI, and 'SCSI disk support' +# + +# +# USB Gadget Support +# +# CONFIG_USB_GADGET is not set + +# +# MMC/SD Card support +# +CONFIG_MMC=y +# CONFIG_MMC_DEBUG is not set +CONFIG_MMC_BLOCK=y +CONFIG_MMC_AT91=y + +# +# Real Time Clock +# +CONFIG_RTC_LIB=y +# CONFIG_RTC_CLASS is not set + +# +# File systems +# +CONFIG_EXT2_FS=y +# CONFIG_EXT2_FS_XATTR is not set +# CONFIG_EXT2_FS_XIP is not set +# CONFIG_EXT3_FS is not set +# CONFIG_EXT4DEV_FS is not set +# CONFIG_REISERFS_FS is not set +# CONFIG_JFS_FS is not set +# CONFIG_FS_POSIX_ACL is not set +# CONFIG_XFS_FS is not set +# CONFIG_GFS2_FS is not set +# CONFIG_OCFS2_FS is not set +# CONFIG_MINIX_FS is not set +# CONFIG_ROMFS_FS is not set +CONFIG_INOTIFY=y +CONFIG_INOTIFY_USER=y +# CONFIG_QUOTA is not set +CONFIG_DNOTIFY=y +# CONFIG_AUTOFS_FS is not set +# CONFIG_AUTOFS4_FS is not set +# CONFIG_FUSE_FS is not set + +# +# CD-ROM/DVD Filesystems +# +# CONFIG_ISO9660_FS is not set +# CONFIG_UDF_FS is not set + +# +# DOS/FAT/NT Filesystems +# +CONFIG_FAT_FS=y +CONFIG_MSDOS_FS=y +CONFIG_VFAT_FS=y +CONFIG_FAT_DEFAULT_CODEPAGE=437 +CONFIG_FAT_DEFAULT_IOCHARSET="iso8859-1" +# CONFIG_NTFS_FS is not set + +# +# Pseudo filesystems +# +CONFIG_PROC_FS=y +CONFIG_PROC_SYSCTL=y +CONFIG_SYSFS=y +CONFIG_TMPFS=y +# CONFIG_TMPFS_POSIX_ACL is not set +# CONFIG_HUGETLB_PAGE is not set +CONFIG_RAMFS=y +# CONFIG_CONFIGFS_FS is not set + +# +# Miscellaneous filesystems +# +# CONFIG_ADFS_FS is not set +# CONFIG_AFFS_FS is not set +# CONFIG_HFS_FS is not set +# CONFIG_HFSPLUS_FS is not set +# CONFIG_BEFS_FS is not set +# CONFIG_BFS_FS is not set +# CONFIG_EFS_FS is not set +# CONFIG_JFFS2_FS is not set +CONFIG_CRAMFS=y +# CONFIG_VXFS_FS is not set +# CONFIG_HPFS_FS is not set +# CONFIG_QNX4FS_FS is not set +# CONFIG_SYSV_FS is not set +# CONFIG_UFS_FS is not set + +# +# Network File Systems +# + +# +# Partition Types +# +# CONFIG_PARTITION_ADVANCED is not set +CONFIG_MSDOS_PARTITION=y + +# +# Native Language Support +# +CONFIG_NLS=y +CONFIG_NLS_DEFAULT="iso8859-1" +CONFIG_NLS_CODEPAGE_437=y +# CONFIG_NLS_CODEPAGE_737 is not set +# CONFIG_NLS_CODEPAGE_775 is not set +CONFIG_NLS_CODEPAGE_850=y +# CONFIG_NLS_CODEPAGE_852 is not set +# CONFIG_NLS_CODEPAGE_855 is not set +# CONFIG_NLS_CODEPAGE_857 is not set +# CONFIG_NLS_CODEPAGE_860 is not set +# CONFIG_NLS_CODEPAGE_861 is not set +# CONFIG_NLS_CODEPAGE_862 is not set +# CONFIG_NLS_CODEPAGE_863 is not set +# CONFIG_NLS_CODEPAGE_864 is not set +# CONFIG_NLS_CODEPAGE_865 is not set +# CONFIG_NLS_CODEPAGE_866 is not set +# CONFIG_NLS_CODEPAGE_869 is not set +# CONFIG_NLS_CODEPAGE_936 is not set +# CONFIG_NLS_CODEPAGE_950 is not set +# CONFIG_NLS_CODEPAGE_932 is not set +# CONFIG_NLS_CODEPAGE_949 is not set +# CONFIG_NLS_CODEPAGE_874 is not set +# CONFIG_NLS_ISO8859_8 is not set +# CONFIG_NLS_CODEPAGE_1250 is not set +# CONFIG_NLS_CODEPAGE_1251 is not set +# CONFIG_NLS_ASCII is not set +CONFIG_NLS_ISO8859_1=y +# CONFIG_NLS_ISO8859_2 is not set +# CONFIG_NLS_ISO8859_3 is not set +# CONFIG_NLS_ISO8859_4 is not set +# CONFIG_NLS_ISO8859_5 is not set +# CONFIG_NLS_ISO8859_6 is not set +# CONFIG_NLS_ISO8859_7 is not set +# CONFIG_NLS_ISO8859_9 is not set +# CONFIG_NLS_ISO8859_13 is not set +# CONFIG_NLS_ISO8859_14 is not set +CONFIG_NLS_ISO8859_15=y +# CONFIG_NLS_KOI8_R is not set +# CONFIG_NLS_KOI8_U is not set +CONFIG_NLS_UTF8=y + +# +# Profiling support +# +# CONFIG_PROFILING is not set + +# +# Kernel hacking +# +# CONFIG_PRINTK_TIME is not set +CONFIG_ENABLE_MUST_CHECK=y +# CONFIG_MAGIC_SYSRQ is not set +# CONFIG_UNUSED_SYMBOLS is not set +# CONFIG_DEBUG_FS is not set +# CONFIG_HEADERS_CHECK is not set +CONFIG_DEBUG_KERNEL=y +# CONFIG_DEBUG_SHIRQ is not set +CONFIG_LOG_BUF_SHIFT=14 +CONFIG_DETECT_SOFTLOCKUP=y +# CONFIG_SCHEDSTATS is not set +# CONFIG_TIMER_STATS is not set +# CONFIG_DEBUG_SLAB is not set +# CONFIG_DEBUG_RT_MUTEXES is not set +# CONFIG_RT_MUTEX_TESTER is not set +# CONFIG_DEBUG_SPINLOCK is not set +# CONFIG_DEBUG_MUTEXES is not set +# CONFIG_DEBUG_SPINLOCK_SLEEP is not set +# CONFIG_DEBUG_LOCKING_API_SELFTESTS is not set +# CONFIG_DEBUG_KOBJECT is not set +CONFIG_DEBUG_BUGVERBOSE=y +CONFIG_DEBUG_INFO=y +# CONFIG_DEBUG_VM is not set +# CONFIG_DEBUG_LIST is not set +CONFIG_FRAME_POINTER=y +CONFIG_FORCED_INLINING=y +# CONFIG_RCU_TORTURE_TEST is not set +# CONFIG_FAULT_INJECTION is not set +CONFIG_DEBUG_USER=y +# CONFIG_DEBUG_ERRORS is not set +CONFIG_DEBUG_LL=y +# CONFIG_DEBUG_ICEDCC is not set + +# +# Security options +# +# CONFIG_KEYS is not set +# CONFIG_SECURITY is not set + +# +# Cryptographic options +# +# CONFIG_CRYPTO is not set + +# +# Library routines +# +CONFIG_BITREVERSE=y +# CONFIG_CRC_CCITT is not set +# CONFIG_CRC16 is not set +CONFIG_CRC32=y +# CONFIG_LIBCRC32C is not set +CONFIG_ZLIB_INFLATE=y +CONFIG_PLIST=y +CONFIG_HAS_IOMEM=y +CONFIG_HAS_IOPORT=y diff --git a/arch/arm/configs/ks8695_defconfig b/arch/arm/configs/ks8695_defconfig new file mode 100644 index 00000000000..8ab21a0719e --- /dev/null +++ b/arch/arm/configs/ks8695_defconfig @@ -0,0 +1,880 @@ +# +# Automatically generated make config: don't edit +# Linux kernel version: 2.6.17-rc4 +# Thu May 25 15:42:51 2006 +# +CONFIG_ARM=y +CONFIG_MMU=y +CONFIG_RWSEM_GENERIC_SPINLOCK=y +CONFIG_GENERIC_HWEIGHT=y +CONFIG_GENERIC_CALIBRATE_DELAY=y +CONFIG_VECTORS_BASE=0xffff0000 + +# +# Code maturity level options +# +CONFIG_EXPERIMENTAL=y +CONFIG_BROKEN_ON_SMP=y +CONFIG_INIT_ENV_ARG_LIMIT=32 + +# +# General setup +# +CONFIG_LOCALVERSION="" +CONFIG_LOCALVERSION_AUTO=y +# CONFIG_SWAP is not set +CONFIG_SYSVIPC=y +# CONFIG_POSIX_MQUEUE is not set +# CONFIG_BSD_PROCESS_ACCT is not set +CONFIG_SYSCTL=y +# CONFIG_AUDIT is not set +# CONFIG_IKCONFIG is not set +# CONFIG_RELAY is not set +CONFIG_INITRAMFS_SOURCE="" +CONFIG_UID16=y +CONFIG_CC_OPTIMIZE_FOR_SIZE=y +# CONFIG_EMBEDDED is not set +CONFIG_KALLSYMS=y +# CONFIG_KALLSYMS_ALL is not set +# CONFIG_KALLSYMS_EXTRA_PASS is not set +CONFIG_HOTPLUG=y +CONFIG_PRINTK=y +CONFIG_BUG=y +CONFIG_ELF_CORE=y +CONFIG_BASE_FULL=y +CONFIG_FUTEX=y +CONFIG_EPOLL=y +CONFIG_SHMEM=y +CONFIG_SLAB=y +# CONFIG_TINY_SHMEM is not set +CONFIG_BASE_SMALL=0 +# CONFIG_SLOB is not set +CONFIG_OBSOLETE_INTERMODULE=y + +# +# Loadable module support +# +CONFIG_MODULES=y +CONFIG_MODULE_UNLOAD=y +# CONFIG_MODULE_FORCE_UNLOAD is not set +# CONFIG_MODVERSIONS is not set +# CONFIG_MODULE_SRCVERSION_ALL is not set +CONFIG_KMOD=y + +# +# Block layer +# +# CONFIG_BLK_DEV_IO_TRACE is not set + +# +# IO Schedulers +# +CONFIG_IOSCHED_NOOP=y +CONFIG_IOSCHED_AS=y +# CONFIG_IOSCHED_DEADLINE is not set +# CONFIG_IOSCHED_CFQ is not set +CONFIG_DEFAULT_AS=y +# CONFIG_DEFAULT_DEADLINE is not set +# CONFIG_DEFAULT_CFQ is not set +# CONFIG_DEFAULT_NOOP is not set +CONFIG_DEFAULT_IOSCHED="anticipatory" + +# +# System Type +# +# CONFIG_ARCH_CLPS7500 is not set +# CONFIG_ARCH_CLPS711X is not set +# CONFIG_ARCH_CO285 is not set +# CONFIG_ARCH_EBSA110 is not set +# CONFIG_ARCH_EP93XX is not set +# CONFIG_ARCH_FOOTBRIDGE is not set +# CONFIG_ARCH_INTEGRATOR is not set +# CONFIG_ARCH_IOP3XX is not set +# CONFIG_ARCH_IXP4XX is not set +# CONFIG_ARCH_IXP2000 is not set +# CONFIG_ARCH_IXP23XX is not set +# CONFIG_ARCH_L7200 is not set +# CONFIG_ARCH_PXA is not set +# CONFIG_ARCH_RPC is not set +# CONFIG_ARCH_SA1100 is not set +# CONFIG_ARCH_S3C2410 is not set +# CONFIG_ARCH_SHARK is not set +# CONFIG_ARCH_LH7A40X is not set +# CONFIG_ARCH_OMAP is not set +# CONFIG_ARCH_VERSATILE is not set +# CONFIG_ARCH_REALVIEW is not set +# CONFIG_ARCH_IMX is not set +# CONFIG_ARCH_H720X is not set +# CONFIG_ARCH_AAEC2000 is not set +# CONFIG_ARCH_AT91 is not set +CONFIG_ARCH_KS8695=y + +# +# Kendin/Micrel KS8695 Implementations +# +CONFIG_MACH_KS8695=y +# CONFIG_MACH_DSM320 is not set +# CONFIG_MACH_CM4002 is not set +# CONFIG_MACH_CM4008 is not set +# CONFIG_MACH_CM40xx is not set +# CONFIG_MACH_LITE300 is not set +# CONFIG_MACH_SE4200 is not set +# CONFIG_MACH_MANGA_KS8695 is not set + +# +# Processor Type +# +CONFIG_CPU_32=y +CONFIG_CPU_ARM922T=y +CONFIG_CPU_32v4=y +CONFIG_CPU_ABRT_EV4T=y +CONFIG_CPU_CACHE_V4WT=y +CONFIG_CPU_CACHE_VIVT=y +CONFIG_CPU_COPY_V4WB=y +CONFIG_CPU_TLB_V4WBI=y + +# +# Processor Features +# +# CONFIG_ARM_THUMB is not set +# CONFIG_CPU_ICACHE_DISABLE is not set +# CONFIG_CPU_DCACHE_DISABLE is not set +# CONFIG_CPU_DCACHE_WRITETHROUGH is not set + +# +# Bus support +# +CONFIG_PCI=y +CONFIG_PCI_DEBUG=y + +# +# PCCARD (PCMCIA/CardBus) support +# +CONFIG_PCCARD=y +# CONFIG_PCMCIA_DEBUG is not set +CONFIG_PCMCIA=y +CONFIG_PCMCIA_LOAD_CIS=y +CONFIG_PCMCIA_IOCTL=y +CONFIG_CARDBUS=y + +# +# PC-card bridges +# +CONFIG_YENTA=y +CONFIG_YENTA_O2=y +CONFIG_YENTA_RICOH=y +CONFIG_YENTA_TI=y +CONFIG_YENTA_ENE_TUNE=y +CONFIG_YENTA_TOSHIBA=y +# CONFIG_PD6729 is not set +# CONFIG_I82092 is not set +CONFIG_PCCARD_NONSTATIC=y + +# +# Kernel Features +# +# CONFIG_PREEMPT is not set +# CONFIG_NO_IDLE_HZ is not set +CONFIG_HZ=100 +# CONFIG_AEABI is not set +# CONFIG_ARCH_DISCONTIGMEM_ENABLE is not set +CONFIG_SELECT_MEMORY_MODEL=y +CONFIG_FLATMEM_MANUAL=y +# CONFIG_DISCONTIGMEM_MANUAL is not set +# CONFIG_SPARSEMEM_MANUAL is not set +CONFIG_FLATMEM=y +CONFIG_FLAT_NODE_MEM_MAP=y +# CONFIG_SPARSEMEM_STATIC is not set +CONFIG_SPLIT_PTLOCK_CPUS=4096 +CONFIG_ALIGNMENT_TRAP=y + +# +# Boot options +# +CONFIG_ZBOOT_ROM_TEXT=0x0 +CONFIG_ZBOOT_ROM_BSS=0x0 +CONFIG_CMDLINE="mem=32M console=ttyS0,115200 initrd=0x20410000,3145728 root=/dev/ram0 rw" +# CONFIG_XIP_KERNEL is not set + +# +# Floating point emulation +# + +# +# At least one emulation must be selected +# +CONFIG_FPE_NWFPE=y +# CONFIG_FPE_NWFPE_XP is not set +# CONFIG_FPE_FASTFPE is not set + +# +# Userspace binary formats +# +CONFIG_BINFMT_ELF=y +# CONFIG_BINFMT_AOUT is not set +# CONFIG_BINFMT_MISC is not set +# CONFIG_ARTHUR is not set + +# +# Power management options +# +# CONFIG_PM is not set +# CONFIG_APM is not set + +# +# Networking +# +CONFIG_NET=y + +# +# Networking options +# +# CONFIG_NETDEBUG is not set +CONFIG_PACKET=y +# CONFIG_PACKET_MMAP is not set +CONFIG_UNIX=y +# CONFIG_NET_KEY is not set +CONFIG_INET=y +# CONFIG_IP_MULTICAST is not set +# CONFIG_IP_ADVANCED_ROUTER is not set +CONFIG_IP_FIB_HASH=y +CONFIG_IP_PNP=y +# CONFIG_IP_PNP_DHCP is not set +CONFIG_IP_PNP_BOOTP=y +# CONFIG_IP_PNP_RARP is not set +# CONFIG_NET_IPIP is not set +# CONFIG_NET_IPGRE is not set +# CONFIG_ARPD is not set +# CONFIG_SYN_COOKIES is not set +# CONFIG_INET_AH is not set +# CONFIG_INET_ESP is not set +# CONFIG_INET_IPCOMP is not set +# CONFIG_INET_XFRM_TUNNEL is not set +# CONFIG_INET_TUNNEL is not set +CONFIG_INET_DIAG=y +CONFIG_INET_TCP_DIAG=y +# CONFIG_TCP_CONG_ADVANCED is not set +CONFIG_TCP_CONG_BIC=y +# CONFIG_IPV6 is not set +# CONFIG_INET6_XFRM_TUNNEL is not set +# CONFIG_INET6_TUNNEL is not set +# CONFIG_NETFILTER is not set + +# +# DCCP Configuration (EXPERIMENTAL) +# +# CONFIG_IP_DCCP is not set + +# +# SCTP Configuration (EXPERIMENTAL) +# +# CONFIG_IP_SCTP is not set + +# +# TIPC Configuration (EXPERIMENTAL) +# +# CONFIG_TIPC is not set +# CONFIG_ATM is not set +# CONFIG_BRIDGE is not set +# CONFIG_VLAN_8021Q is not set +# CONFIG_DECNET is not set +# CONFIG_LLC2 is not set +# CONFIG_IPX is not set +# CONFIG_ATALK is not set +# CONFIG_X25 is not set +# CONFIG_LAPB is not set +# CONFIG_NET_DIVERT is not set +# CONFIG_ECONET is not set +# CONFIG_WAN_ROUTER is not set + +# +# QoS and/or fair queueing +# +# CONFIG_NET_SCHED is not set + +# +# Network testing +# +# CONFIG_NET_PKTGEN is not set +# CONFIG_HAMRADIO is not set +# CONFIG_IRDA is not set +# CONFIG_BT is not set +# CONFIG_IEEE80211 is not set + +# +# Device Drivers +# + +# +# Generic Driver Options +# +CONFIG_STANDALONE=y +CONFIG_PREVENT_FIRMWARE_BUILD=y +CONFIG_FW_LOADER=y +# CONFIG_DEBUG_DRIVER is not set + +# +# Connector - unified userspace <-> kernelspace linker +# +# CONFIG_CONNECTOR is not set + +# +# Memory Technology Devices (MTD) +# +CONFIG_MTD=y +# CONFIG_MTD_DEBUG is not set +# CONFIG_MTD_CONCAT is not set +CONFIG_MTD_PARTITIONS=y +# CONFIG_MTD_REDBOOT_PARTS is not set +CONFIG_MTD_CMDLINE_PARTS=y +# CONFIG_MTD_AFS_PARTS is not set + +# +# User Modules And Translation Layers +# +CONFIG_MTD_CHAR=y +CONFIG_MTD_BLOCK=y +# CONFIG_FTL is not set +# CONFIG_NFTL is not set +# CONFIG_INFTL is not set +# CONFIG_RFD_FTL is not set + +# +# RAM/ROM/Flash chip drivers +# +CONFIG_MTD_CFI=y +CONFIG_MTD_JEDECPROBE=y +CONFIG_MTD_GEN_PROBE=y +# CONFIG_MTD_CFI_ADV_OPTIONS is not set +CONFIG_MTD_MAP_BANK_WIDTH_1=y +CONFIG_MTD_MAP_BANK_WIDTH_2=y +CONFIG_MTD_MAP_BANK_WIDTH_4=y +# CONFIG_MTD_MAP_BANK_WIDTH_8 is not set +# CONFIG_MTD_MAP_BANK_WIDTH_16 is not set +# CONFIG_MTD_MAP_BANK_WIDTH_32 is not set +CONFIG_MTD_CFI_I1=y +CONFIG_MTD_CFI_I2=y +# CONFIG_MTD_CFI_I4 is not set +# CONFIG_MTD_CFI_I8 is not set +# CONFIG_MTD_CFI_INTELEXT is not set +CONFIG_MTD_CFI_AMDSTD=y +# CONFIG_MTD_CFI_STAA is not set +CONFIG_MTD_CFI_UTIL=y +# CONFIG_MTD_RAM is not set +# CONFIG_MTD_ROM is not set +# CONFIG_MTD_ABSENT is not set +# CONFIG_MTD_OBSOLETE_CHIPS is not set + +# +# Mapping drivers for chip access +# +# CONFIG_MTD_COMPLEX_MAPPINGS is not set +# CONFIG_MTD_PHYSMAP is not set +# CONFIG_MTD_ARM_INTEGRATOR is not set +# CONFIG_MTD_IMPA7 is not set +# CONFIG_MTD_PLATRAM is not set + +# +# Self-contained MTD device drivers +# +# CONFIG_MTD_PMC551 is not set +# CONFIG_MTD_SLRAM is not set +# CONFIG_MTD_PHRAM is not set +# CONFIG_MTD_MTDRAM is not set +# CONFIG_MTD_BLOCK2MTD is not set + +# +# Disk-On-Chip Device Drivers +# +# CONFIG_MTD_DOC2000 is not set +# CONFIG_MTD_DOC2001 is not set +# CONFIG_MTD_DOC2001PLUS is not set + +# +# NAND Flash Device Drivers +# +# CONFIG_MTD_NAND is not set + +# +# OneNAND Flash Device Drivers +# +# CONFIG_MTD_ONENAND is not set + +# +# Parallel port support +# +# CONFIG_PARPORT is not set + +# +# Plug and Play support +# + +# +# Block devices +# +# CONFIG_BLK_CPQ_DA is not set +# CONFIG_BLK_CPQ_CISS_DA is not set +# CONFIG_BLK_DEV_DAC960 is not set +# CONFIG_BLK_DEV_UMEM is not set +# CONFIG_BLK_DEV_COW_COMMON is not set +# CONFIG_BLK_DEV_LOOP is not set +# CONFIG_BLK_DEV_NBD is not set +# CONFIG_BLK_DEV_SX8 is not set +CONFIG_BLK_DEV_RAM=y +CONFIG_BLK_DEV_RAM_COUNT=16 +CONFIG_BLK_DEV_RAM_SIZE=8192 +CONFIG_BLK_DEV_INITRD=y +# CONFIG_CDROM_PKTCDVD is not set +# CONFIG_ATA_OVER_ETH is not set + +# +# ATA/ATAPI/MFM/RLL support +# +# CONFIG_IDE is not set + +# +# SCSI device support +# +# CONFIG_RAID_ATTRS is not set +# CONFIG_SCSI is not set + +# +# Multi-device support (RAID and LVM) +# +# CONFIG_MD is not set + +# +# Fusion MPT device support +# +# CONFIG_FUSION is not set + +# +# IEEE 1394 (FireWire) support +# +# CONFIG_IEEE1394 is not set + +# +# I2O device support +# +# CONFIG_I2O is not set + +# +# Network device support +# +CONFIG_NETDEVICES=y +# CONFIG_DUMMY is not set +# CONFIG_BONDING is not set +# CONFIG_EQUALIZER is not set +# CONFIG_TUN is not set + +# +# ARCnet devices +# +# CONFIG_ARCNET is not set + +# +# PHY device support +# +# CONFIG_PHYLIB is not set + +# +# Ethernet (10 or 100Mbit) +# +CONFIG_NET_ETHERNET=y +# CONFIG_MII is not set +CONFIG_ARM_KS8695_ETHER=y +# CONFIG_HAPPYMEAL is not set +# CONFIG_SUNGEM is not set +# CONFIG_CASSINI is not set +# CONFIG_NET_VENDOR_3COM is not set +# CONFIG_SMC91X is not set +# CONFIG_DM9000 is not set + +# +# Tulip family network device support +# +# CONFIG_NET_TULIP is not set +# CONFIG_HP100 is not set +# CONFIG_NET_PCI is not set + +# +# Ethernet (1000 Mbit) +# +# CONFIG_ACENIC is not set +# CONFIG_DL2K is not set +# CONFIG_E1000 is not set +# CONFIG_NS83820 is not set +# CONFIG_HAMACHI is not set +# CONFIG_YELLOWFIN is not set +# CONFIG_R8169 is not set +# CONFIG_SIS190 is not set +# CONFIG_SKGE is not set +# CONFIG_SKY2 is not set +# CONFIG_SK98LIN is not set +# CONFIG_TIGON3 is not set +# CONFIG_BNX2 is not set + +# +# Ethernet (10000 Mbit) +# +# CONFIG_CHELSIO_T1 is not set +# CONFIG_IXGB is not set +# CONFIG_S2IO is not set + +# +# Token Ring devices +# +# CONFIG_TR is not set + +# +# Wireless LAN (non-hamradio) +# +# CONFIG_NET_RADIO is not set + +# +# PCMCIA network device support +# +# CONFIG_NET_PCMCIA is not set + +# +# Wan interfaces +# +# CONFIG_WAN is not set +# CONFIG_FDDI is not set +# CONFIG_HIPPI is not set +# CONFIG_PPP is not set +# CONFIG_SLIP is not set +# CONFIG_SHAPER is not set +# CONFIG_NETCONSOLE is not set +# CONFIG_NETPOLL is not set +# CONFIG_NET_POLL_CONTROLLER is not set + +# +# ISDN subsystem +# +# CONFIG_ISDN is not set + +# +# Input device support +# +CONFIG_INPUT=y + +# +# Userland interfaces +# +CONFIG_INPUT_MOUSEDEV=y +# CONFIG_INPUT_MOUSEDEV_PSAUX is not set +CONFIG_INPUT_MOUSEDEV_SCREEN_X=1024 +CONFIG_INPUT_MOUSEDEV_SCREEN_Y=768 +# CONFIG_INPUT_JOYDEV is not set +# CONFIG_INPUT_TSDEV is not set +# CONFIG_INPUT_EVDEV is not set +# CONFIG_INPUT_EVBUG is not set + +# +# Input Device Drivers +# +# CONFIG_INPUT_KEYBOARD is not set +# CONFIG_INPUT_MOUSE is not set +# CONFIG_INPUT_JOYSTICK is not set +# CONFIG_INPUT_TOUCHSCREEN is not set +# CONFIG_INPUT_MISC is not set + +# +# Hardware I/O ports +# +# CONFIG_SERIO is not set +# CONFIG_GAMEPORT is not set + +# +# Character devices +# +CONFIG_VT=y +CONFIG_VT_CONSOLE=y +CONFIG_HW_CONSOLE=y +# CONFIG_SERIAL_NONSTANDARD is not set + +# +# Serial drivers +# +# CONFIG_SERIAL_8250 is not set + +# +# Non-8250 serial port support +# +CONFIG_SERIAL_KS8695=y +CONFIG_SERIAL_KS8695_CONSOLE=y +CONFIG_SERIAL_CORE=y +CONFIG_SERIAL_CORE_CONSOLE=y +# CONFIG_SERIAL_JSM is not set +CONFIG_UNIX98_PTYS=y +CONFIG_LEGACY_PTYS=y +CONFIG_LEGACY_PTY_COUNT=256 + +# +# IPMI +# +# CONFIG_IPMI_HANDLER is not set + +# +# Watchdog Cards +# +# CONFIG_WATCHDOG is not set +# CONFIG_NVRAM is not set +# CONFIG_DTLK is not set +# CONFIG_R3964 is not set +# CONFIG_APPLICOM is not set + +# +# Ftape, the floppy tape device driver +# +# CONFIG_DRM is not set + +# +# PCMCIA character devices +# +# CONFIG_SYNCLINK_CS is not set +# CONFIG_CARDMAN_4000 is not set +# CONFIG_CARDMAN_4040 is not set +# CONFIG_RAW_DRIVER is not set + +# +# TPM devices +# +# CONFIG_TCG_TPM is not set +# CONFIG_TELCLOCK is not set + +# +# I2C support +# +# CONFIG_I2C is not set + +# +# SPI support +# +# CONFIG_SPI is not set +# CONFIG_SPI_MASTER is not set + +# +# Dallas's 1-wire bus +# +# CONFIG_W1 is not set + +# +# Hardware Monitoring support +# +# CONFIG_HWMON is not set +# CONFIG_HWMON_VID is not set + +# +# Misc devices +# + +# +# LED devices +# +# CONFIG_NEW_LEDS is not set + +# +# LED drivers +# + +# +# LED Triggers +# + +# +# Multimedia devices +# +# CONFIG_VIDEO_DEV is not set + +# +# Digital Video Broadcasting Devices +# +# CONFIG_DVB is not set + +# +# Graphics support +# +# CONFIG_FB is not set + +# +# Console display driver support +# +# CONFIG_VGA_CONSOLE is not set +CONFIG_DUMMY_CONSOLE=y + +# +# Sound +# +# CONFIG_SOUND is not set + +# +# USB support +# +CONFIG_USB_ARCH_HAS_HCD=y +CONFIG_USB_ARCH_HAS_OHCI=y +CONFIG_USB_ARCH_HAS_EHCI=y +# CONFIG_USB is not set + +# +# NOTE: USB_STORAGE enables SCSI, and 'SCSI disk support' +# + +# +# USB Gadget Support +# +# CONFIG_USB_GADGET is not set + +# +# MMC/SD Card support +# +# CONFIG_MMC is not set + +# +# Real Time Clock +# +CONFIG_RTC_LIB=y +# CONFIG_RTC_CLASS is not set + +# +# File systems +# +CONFIG_EXT2_FS=y +# CONFIG_EXT2_FS_XATTR is not set +# CONFIG_EXT2_FS_XIP is not set +# CONFIG_EXT3_FS is not set +# CONFIG_REISERFS_FS is not set +# CONFIG_JFS_FS is not set +# CONFIG_FS_POSIX_ACL is not set +# CONFIG_XFS_FS is not set +# CONFIG_OCFS2_FS is not set +# CONFIG_MINIX_FS is not set +# CONFIG_ROMFS_FS is not set +CONFIG_INOTIFY=y +# CONFIG_QUOTA is not set +CONFIG_DNOTIFY=y +# CONFIG_AUTOFS_FS is not set +# CONFIG_AUTOFS4_FS is not set +# CONFIG_FUSE_FS is not set + +# +# CD-ROM/DVD Filesystems +# +# CONFIG_ISO9660_FS is not set +# CONFIG_UDF_FS is not set + +# +# DOS/FAT/NT Filesystems +# +# CONFIG_MSDOS_FS is not set +# CONFIG_VFAT_FS is not set +# CONFIG_NTFS_FS is not set + +# +# Pseudo filesystems +# +CONFIG_PROC_FS=y +CONFIG_SYSFS=y +CONFIG_TMPFS=y +# CONFIG_HUGETLB_PAGE is not set +CONFIG_RAMFS=y +# CONFIG_CONFIGFS_FS is not set + +# +# Miscellaneous filesystems +# +# CONFIG_ADFS_FS is not set +# CONFIG_AFFS_FS is not set +# CONFIG_HFS_FS is not set +# CONFIG_HFSPLUS_FS is not set +# CONFIG_BEFS_FS is not set +# CONFIG_BFS_FS is not set +# CONFIG_EFS_FS is not set +# CONFIG_JFFS_FS is not set +# CONFIG_JFFS2_FS is not set +CONFIG_CRAMFS=y +# CONFIG_VXFS_FS is not set +# CONFIG_HPFS_FS is not set +# CONFIG_QNX4FS_FS is not set +# CONFIG_SYSV_FS is not set +# CONFIG_UFS_FS is not set + +# +# Network File Systems +# +# CONFIG_NFS_FS is not set +# CONFIG_NFSD is not set +# CONFIG_SMB_FS is not set +# CONFIG_CIFS is not set +# CONFIG_NCP_FS is not set +# CONFIG_CODA_FS is not set +# CONFIG_AFS_FS is not set +# CONFIG_9P_FS is not set + +# +# Partition Types +# +# CONFIG_PARTITION_ADVANCED is not set +CONFIG_MSDOS_PARTITION=y + +# +# Native Language Support +# +# CONFIG_NLS is not set + +# +# Profiling support +# +# CONFIG_PROFILING is not set + +# +# Kernel hacking +# +# CONFIG_PRINTK_TIME is not set +# CONFIG_MAGIC_SYSRQ is not set +CONFIG_DEBUG_KERNEL=y +CONFIG_LOG_BUF_SHIFT=14 +CONFIG_DETECT_SOFTLOCKUP=y +# CONFIG_SCHEDSTATS is not set +# CONFIG_DEBUG_SLAB is not set +CONFIG_DEBUG_MUTEXES=y +# CONFIG_DEBUG_SPINLOCK is not set +# CONFIG_DEBUG_SPINLOCK_SLEEP is not set +# CONFIG_DEBUG_KOBJECT is not set +CONFIG_DEBUG_BUGVERBOSE=y +# CONFIG_DEBUG_INFO is not set +# CONFIG_DEBUG_FS is not set +# CONFIG_DEBUG_VM is not set +CONFIG_FRAME_POINTER=y +# CONFIG_UNWIND_INFO is not set +CONFIG_FORCED_INLINING=y +# CONFIG_RCU_TORTURE_TEST is not set +CONFIG_DEBUG_USER=y +# CONFIG_DEBUG_ERRORS is not set +CONFIG_DEBUG_LL=y +# CONFIG_DEBUG_ICEDCC is not set + +# +# Security options +# +# CONFIG_KEYS is not set +# CONFIG_SECURITY is not set + +# +# Cryptographic options +# +# CONFIG_CRYPTO is not set + +# +# Hardware crypto devices +# + +# +# Library routines +# +# CONFIG_CRC_CCITT is not set +# CONFIG_CRC16 is not set +CONFIG_CRC32=y +# CONFIG_LIBCRC32C is not set +CONFIG_ZLIB_INFLATE=y diff --git a/arch/arm/configs/trizeps4_defconfig b/arch/arm/configs/trizeps4_defconfig index a6698dc4f6b..6db6392806f 100644 --- a/arch/arm/configs/trizeps4_defconfig +++ b/arch/arm/configs/trizeps4_defconfig @@ -1,15 +1,27 @@ # # Automatically generated make config: don't edit -# Linux kernel version: 2.6.17 -# Sat Jun 24 22:45:14 2006 +# Linux kernel version: 2.6.21 +# Mon Apr 30 21:23:20 2007 # CONFIG_ARM=y +CONFIG_SYS_SUPPORTS_APM_EMULATION=y +CONFIG_GENERIC_GPIO=y +CONFIG_GENERIC_TIME=y CONFIG_MMU=y +# CONFIG_NO_IOPORT is not set +CONFIG_GENERIC_HARDIRQS=y +CONFIG_TRACE_IRQFLAGS_SUPPORT=y +CONFIG_HARDIRQS_SW_RESEND=y +CONFIG_GENERIC_IRQ_PROBE=y CONFIG_RWSEM_GENERIC_SPINLOCK=y +# CONFIG_ARCH_HAS_ILOG2_U32 is not set +# CONFIG_ARCH_HAS_ILOG2_U64 is not set CONFIG_GENERIC_HWEIGHT=y CONFIG_GENERIC_CALIBRATE_DELAY=y +CONFIG_ZONE_DMA=y CONFIG_ARCH_MTD_XIP=y CONFIG_VECTORS_BASE=0xffff0000 +CONFIG_DEFCONFIG_LIST="/lib/modules/$UNAME_RELEASE/.config" # # Code maturity level options @@ -26,18 +38,25 @@ CONFIG_LOCALVERSION="" CONFIG_LOCALVERSION_AUTO=y CONFIG_SWAP=y CONFIG_SYSVIPC=y +# CONFIG_IPC_NS is not set +CONFIG_SYSVIPC_SYSCTL=y CONFIG_POSIX_MQUEUE=y CONFIG_BSD_PROCESS_ACCT=y CONFIG_BSD_PROCESS_ACCT_V3=y -CONFIG_SYSCTL=y -CONFIG_AUDIT=y +# CONFIG_TASKSTATS is not set +# CONFIG_UTS_NS is not set +# CONFIG_AUDIT is not set CONFIG_IKCONFIG=y CONFIG_IKCONFIG_PROC=y +CONFIG_SYSFS_DEPRECATED=y # CONFIG_RELAY is not set +CONFIG_BLK_DEV_INITRD=y CONFIG_INITRAMFS_SOURCE="" -CONFIG_UID16=y CONFIG_CC_OPTIMIZE_FOR_SIZE=y +CONFIG_SYSCTL=y CONFIG_EMBEDDED=y +CONFIG_UID16=y +CONFIG_SYSCTL_SYSCALL=y CONFIG_KALLSYMS=y CONFIG_KALLSYMS_EXTRA_PASS=y CONFIG_HOTPLUG=y @@ -49,10 +68,11 @@ CONFIG_FUTEX=y CONFIG_EPOLL=y CONFIG_SHMEM=y CONFIG_SLAB=y +CONFIG_VM_EVENT_COUNTERS=y +CONFIG_RT_MUTEXES=y # CONFIG_TINY_SHMEM is not set CONFIG_BASE_SMALL=0 # CONFIG_SLOB is not set -CONFIG_OBSOLETE_INTERMODULE=y # # Loadable module support @@ -60,14 +80,17 @@ CONFIG_OBSOLETE_INTERMODULE=y CONFIG_MODULES=y CONFIG_MODULE_UNLOAD=y CONFIG_MODULE_FORCE_UNLOAD=y -# CONFIG_MODVERSIONS is not set +CONFIG_MODVERSIONS=y CONFIG_MODULE_SRCVERSION_ALL=y CONFIG_KMOD=y # # Block layer # +CONFIG_BLOCK=y +CONFIG_LBD=y # CONFIG_BLK_DEV_IO_TRACE is not set +CONFIG_LSF=y # # IO Schedulers @@ -85,18 +108,29 @@ CONFIG_DEFAULT_IOSCHED="anticipatory" # # System Type # +# CONFIG_ARCH_AAEC2000 is not set +# CONFIG_ARCH_INTEGRATOR is not set +# CONFIG_ARCH_REALVIEW is not set +# CONFIG_ARCH_VERSATILE is not set +# CONFIG_ARCH_AT91 is not set # CONFIG_ARCH_CLPS7500 is not set # CONFIG_ARCH_CLPS711X is not set # CONFIG_ARCH_CO285 is not set # CONFIG_ARCH_EBSA110 is not set # CONFIG_ARCH_EP93XX is not set # CONFIG_ARCH_FOOTBRIDGE is not set -# CONFIG_ARCH_INTEGRATOR is not set -# CONFIG_ARCH_IOP3XX is not set +# CONFIG_ARCH_NETX is not set +# CONFIG_ARCH_H720X is not set +# CONFIG_ARCH_IMX is not set +# CONFIG_ARCH_IOP32X is not set +# CONFIG_ARCH_IOP33X is not set +# CONFIG_ARCH_IOP13XX is not set # CONFIG_ARCH_IXP4XX is not set # CONFIG_ARCH_IXP2000 is not set # CONFIG_ARCH_IXP23XX is not set # CONFIG_ARCH_L7200 is not set +# CONFIG_ARCH_NS9XXX is not set +# CONFIG_ARCH_PNX4008 is not set CONFIG_ARCH_PXA=y # CONFIG_ARCH_RPC is not set # CONFIG_ARCH_SA1100 is not set @@ -104,12 +138,6 @@ CONFIG_ARCH_PXA=y # CONFIG_ARCH_SHARK is not set # CONFIG_ARCH_LH7A40X is not set # CONFIG_ARCH_OMAP is not set -# CONFIG_ARCH_VERSATILE is not set -# CONFIG_ARCH_REALVIEW is not set -# CONFIG_ARCH_IMX is not set -# CONFIG_ARCH_H720X is not set -# CONFIG_ARCH_AAEC2000 is not set -# CONFIG_ARCH_AT91RM9200 is not set # # Intel PXA2xx Implementations @@ -133,11 +161,16 @@ CONFIG_CPU_32v5=y CONFIG_CPU_ABRT_EV5T=y CONFIG_CPU_CACHE_VIVT=y CONFIG_CPU_TLB_V4WBI=y +CONFIG_CPU_CP15=y +CONFIG_CPU_CP15_MMU=y # # Processor Features # CONFIG_ARM_THUMB=y +# CONFIG_CPU_DCACHE_DISABLE is not set +# CONFIG_OUTER_CACHE is not set +CONFIG_IWMMXT=y CONFIG_XSCALE_PMU=y # @@ -147,16 +180,16 @@ CONFIG_XSCALE_PMU=y # # PCCARD (PCMCIA/CardBus) support # -CONFIG_PCCARD=m +CONFIG_PCCARD=y # CONFIG_PCMCIA_DEBUG is not set -CONFIG_PCMCIA=m -CONFIG_PCMCIA_LOAD_CIS=y +CONFIG_PCMCIA=y +# CONFIG_PCMCIA_LOAD_CIS is not set CONFIG_PCMCIA_IOCTL=y # # PC-card bridges # -CONFIG_PCMCIA_PXA2XX=m +CONFIG_PCMCIA_PXA2XX=y # # Kernel Features @@ -164,7 +197,8 @@ CONFIG_PCMCIA_PXA2XX=m CONFIG_PREEMPT=y # CONFIG_NO_IDLE_HZ is not set CONFIG_HZ=100 -# CONFIG_AEABI is not set +CONFIG_AEABI=y +CONFIG_OABI_COMPAT=y # CONFIG_ARCH_DISCONTIGMEM_ENABLE is not set CONFIG_SELECT_MEMORY_MODEL=y CONFIG_FLATMEM_MANUAL=y @@ -174,6 +208,8 @@ CONFIG_FLATMEM=y CONFIG_FLAT_NODE_MEM_MAP=y # CONFIG_SPARSEMEM_STATIC is not set CONFIG_SPLIT_PTLOCK_CPUS=4096 +# CONFIG_RESOURCES_64BIT is not set +CONFIG_ZONE_DMA_FLAG=1 CONFIG_LEDS=y CONFIG_LEDS_TIMER=y CONFIG_LEDS_CPU=y @@ -184,8 +220,9 @@ CONFIG_ALIGNMENT_TRAP=y # CONFIG_ZBOOT_ROM_TEXT=0 CONFIG_ZBOOT_ROM_BSS=0 -CONFIG_CMDLINE="root=/dev/nfs ip=bootp console=ttyS0,115200n8" +CONFIG_CMDLINE="root=fe01 console=ttyS0,38400n8 loglevel=5" # CONFIG_XIP_KERNEL is not set +# CONFIG_KEXEC is not set # # Floating point emulation @@ -203,16 +240,16 @@ CONFIG_FPE_NWFPE_XP=y # CONFIG_BINFMT_ELF=y # CONFIG_BINFMT_AOUT is not set -CONFIG_BINFMT_MISC=m -# CONFIG_ARTHUR is not set +# CONFIG_BINFMT_MISC is not set # # Power management options # CONFIG_PM=y -CONFIG_PM_LEGACY=y +# CONFIG_PM_LEGACY is not set # CONFIG_PM_DEBUG is not set -CONFIG_APM=y +# CONFIG_PM_SYSFS_DEPRECATED is not set +# CONFIG_APM_EMULATION is not set # # Networking @@ -222,13 +259,15 @@ CONFIG_NET=y # # Networking options # -# CONFIG_NETDEBUG is not set CONFIG_PACKET=y CONFIG_PACKET_MMAP=y CONFIG_UNIX=y CONFIG_XFRM=y CONFIG_XFRM_USER=m +# CONFIG_XFRM_SUB_POLICY is not set +# CONFIG_XFRM_MIGRATE is not set CONFIG_NET_KEY=y +# CONFIG_NET_KEY_MIGRATE is not set CONFIG_INET=y # CONFIG_IP_MULTICAST is not set # CONFIG_IP_ADVANCED_ROUTER is not set @@ -246,24 +285,25 @@ CONFIG_IP_PNP_BOOTP=y # CONFIG_INET_IPCOMP is not set # CONFIG_INET_XFRM_TUNNEL is not set # CONFIG_INET_TUNNEL is not set +CONFIG_INET_XFRM_MODE_TRANSPORT=y +CONFIG_INET_XFRM_MODE_TUNNEL=y +CONFIG_INET_XFRM_MODE_BEET=y CONFIG_INET_DIAG=y CONFIG_INET_TCP_DIAG=y # CONFIG_TCP_CONG_ADVANCED is not set -CONFIG_TCP_CONG_BIC=y +CONFIG_TCP_CONG_CUBIC=y +CONFIG_DEFAULT_TCP_CONG="cubic" +# CONFIG_TCP_MD5SIG is not set # # IP: Virtual Server Configuration # # CONFIG_IP_VS is not set -CONFIG_IPV6=m -# CONFIG_IPV6_PRIVACY is not set -# CONFIG_IPV6_ROUTER_PREF is not set -# CONFIG_INET6_AH is not set -# CONFIG_INET6_ESP is not set -# CONFIG_INET6_IPCOMP is not set +# CONFIG_IPV6 is not set # CONFIG_INET6_XFRM_TUNNEL is not set # CONFIG_INET6_TUNNEL is not set -# CONFIG_IPV6_TUNNEL is not set +# CONFIG_NETLABEL is not set +# CONFIG_NETWORK_SECMARK is not set CONFIG_NETFILTER=y # CONFIG_NETFILTER_DEBUG is not set @@ -271,29 +311,16 @@ CONFIG_NETFILTER=y # Core Netfilter Configuration # # CONFIG_NETFILTER_NETLINK is not set +# CONFIG_NF_CONNTRACK_ENABLED is not set +# CONFIG_NF_CONNTRACK is not set # CONFIG_NETFILTER_XTABLES is not set # # IP: Netfilter Configuration # -CONFIG_IP_NF_CONNTRACK=m -CONFIG_IP_NF_CT_ACCT=y -CONFIG_IP_NF_CONNTRACK_MARK=y -# CONFIG_IP_NF_CONNTRACK_EVENTS is not set -# CONFIG_IP_NF_CT_PROTO_SCTP is not set -CONFIG_IP_NF_FTP=m -CONFIG_IP_NF_IRC=m -# CONFIG_IP_NF_NETBIOS_NS is not set -CONFIG_IP_NF_TFTP=m -CONFIG_IP_NF_AMANDA=m -# CONFIG_IP_NF_PPTP is not set -# CONFIG_IP_NF_H323 is not set CONFIG_IP_NF_QUEUE=m - -# -# IPv6: Netfilter Configuration (EXPERIMENTAL) -# -# CONFIG_IP6_NF_QUEUE is not set +# CONFIG_IP_NF_IPTABLES is not set +# CONFIG_IP_NF_ARPTABLES is not set # # DCCP Configuration (EXPERIMENTAL) @@ -318,7 +345,6 @@ CONFIG_VLAN_8021Q=m # CONFIG_ATALK is not set # CONFIG_X25 is not set # CONFIG_LAPB is not set -# CONFIG_NET_DIVERT is not set # CONFIG_ECONET is not set # CONFIG_WAN_ROUTER is not set @@ -378,6 +404,7 @@ CONFIG_IRTTY_SIR=m # CONFIG_USB_IRDA is not set # CONFIG_SIGMATEL_FIR is not set # CONFIG_PXA_FICP is not set +# CONFIG_MCS_FIR is not set CONFIG_BT=m CONFIG_BT_L2CAP=m CONFIG_BT_SCO=m @@ -401,14 +428,20 @@ CONFIG_BT_HIDP=m # CONFIG_BT_HCIBLUECARD is not set # CONFIG_BT_HCIBTUART is not set # CONFIG_BT_HCIVHCI is not set -CONFIG_IEEE80211=m +# CONFIG_AF_RXRPC is not set + +# +# Wireless +# +CONFIG_CFG80211=y +CONFIG_WIRELESS_EXT=y +CONFIG_IEEE80211=y # CONFIG_IEEE80211_DEBUG is not set -CONFIG_IEEE80211_CRYPT_WEP=m +CONFIG_IEEE80211_CRYPT_WEP=y CONFIG_IEEE80211_CRYPT_CCMP=m CONFIG_IEEE80211_CRYPT_TKIP=m CONFIG_IEEE80211_SOFTMAC=m # CONFIG_IEEE80211_SOFTMAC_DEBUG is not set -CONFIG_WIRELESS_EXT=y # # Device Drivers @@ -420,16 +453,13 @@ CONFIG_WIRELESS_EXT=y CONFIG_STANDALONE=y CONFIG_PREVENT_FIRMWARE_BUILD=y CONFIG_FW_LOADER=y +# CONFIG_SYS_HYPERVISOR is not set # # Connector - unified userspace <-> kernelspace linker # CONFIG_CONNECTOR=y CONFIG_PROC_EVENTS=y - -# -# Memory Technology Devices (MTD) -# CONFIG_MTD=y # CONFIG_MTD_DEBUG is not set CONFIG_MTD_CONCAT=y @@ -445,12 +475,13 @@ CONFIG_MTD_REDBOOT_PARTS_READONLY=y # User Modules And Translation Layers # CONFIG_MTD_CHAR=y +CONFIG_MTD_BLKDEVS=y CONFIG_MTD_BLOCK=y # CONFIG_FTL is not set -CONFIG_NFTL=y -CONFIG_NFTL_RW=y -CONFIG_INFTL=y +# CONFIG_NFTL is not set +# CONFIG_INFTL is not set # CONFIG_RFD_FTL is not set +# CONFIG_SSFDC is not set # # RAM/ROM/Flash chip drivers @@ -490,9 +521,8 @@ CONFIG_MTD_CFI_UTIL=y CONFIG_MTD_COMPLEX_MAPPINGS=y CONFIG_MTD_PHYSMAP=y CONFIG_MTD_PHYSMAP_START=0x0 -CONFIG_MTD_PHYSMAP_LEN=0x4000000 +CONFIG_MTD_PHYSMAP_LEN=0x0 CONFIG_MTD_PHYSMAP_BANKWIDTH=2 -# CONFIG_MTD_TRIZEPS4 is not set # CONFIG_MTD_ARM_INTEGRATOR is not set # CONFIG_MTD_IMPA7 is not set # CONFIG_MTD_SHARP_SL is not set @@ -501,42 +531,45 @@ CONFIG_MTD_PHYSMAP_BANKWIDTH=2 # # Self-contained MTD device drivers # -# CONFIG_MTD_DATAFLASH is not set -# CONFIG_MTD_M25P80 is not set # CONFIG_MTD_SLRAM is not set # CONFIG_MTD_PHRAM is not set # CONFIG_MTD_MTDRAM is not set -# CONFIG_MTD_BLOCK2MTD is not set +CONFIG_MTD_BLOCK2MTD=y # # Disk-On-Chip Device Drivers # -# CONFIG_MTD_DOC2000 is not set -# CONFIG_MTD_DOC2001 is not set +CONFIG_MTD_DOC2000=y +CONFIG_MTD_DOC2001=y CONFIG_MTD_DOC2001PLUS=y CONFIG_MTD_DOCPROBE=y CONFIG_MTD_DOCECC=y -# CONFIG_MTD_DOCPROBE_ADVANCED is not set -CONFIG_MTD_DOCPROBE_ADDRESS=0 - -# -# NAND Flash Device Drivers -# +CONFIG_MTD_DOCPROBE_ADVANCED=y +CONFIG_MTD_DOCPROBE_ADDRESS=0x4000000 +CONFIG_MTD_DOCPROBE_HIGH=y +# CONFIG_MTD_DOCPROBE_55AA is not set CONFIG_MTD_NAND=y # CONFIG_MTD_NAND_VERIFY_WRITE is not set +# CONFIG_MTD_NAND_ECC_SMC is not set +# CONFIG_MTD_NAND_MUSEUM_IDS is not set # CONFIG_MTD_NAND_H1900 is not set CONFIG_MTD_NAND_IDS=y CONFIG_MTD_NAND_DISKONCHIP=y -# CONFIG_MTD_NAND_DISKONCHIP_PROBE_ADVANCED is not set -CONFIG_MTD_NAND_DISKONCHIP_PROBE_ADDRESS=0 -# CONFIG_MTD_NAND_DISKONCHIP_BBTWRITE is not set +CONFIG_MTD_NAND_DISKONCHIP_PROBE_ADVANCED=y +CONFIG_MTD_NAND_DISKONCHIP_PROBE_ADDRESS=0x4000000 +CONFIG_MTD_NAND_DISKONCHIP_PROBE_HIGH=y +CONFIG_MTD_NAND_DISKONCHIP_BBTWRITE=y # CONFIG_MTD_NAND_SHARPSL is not set # CONFIG_MTD_NAND_NANDSIM is not set +CONFIG_MTD_ONENAND=y +# CONFIG_MTD_ONENAND_VERIFY_WRITE is not set +# CONFIG_MTD_ONENAND_GENERIC is not set +# CONFIG_MTD_ONENAND_OTP is not set # -# OneNAND Flash Device Drivers +# UBI - Unsorted block images # -# CONFIG_MTD_ONENAND is not set +# CONFIG_MTD_UBI is not set # # Parallel port support @@ -546,6 +579,7 @@ CONFIG_MTD_NAND_DISKONCHIP_PROBE_ADDRESS=0 # # Plug and Play support # +# CONFIG_PNPACPI is not set # # Block devices @@ -556,9 +590,9 @@ CONFIG_BLK_DEV_CRYPTOLOOP=m CONFIG_BLK_DEV_NBD=y # CONFIG_BLK_DEV_UB is not set CONFIG_BLK_DEV_RAM=y -CONFIG_BLK_DEV_RAM_COUNT=4 +CONFIG_BLK_DEV_RAM_COUNT=8 CONFIG_BLK_DEV_RAM_SIZE=4096 -CONFIG_BLK_DEV_INITRD=y +CONFIG_BLK_DEV_RAM_BLOCKSIZE=1024 # CONFIG_CDROM_PKTCDVD is not set # CONFIG_ATA_OVER_ETH is not set @@ -566,6 +600,7 @@ CONFIG_BLK_DEV_INITRD=y # ATA/ATAPI/MFM/RLL support # CONFIG_IDE=y +CONFIG_IDE_MAX_HWIFS=4 CONFIG_BLK_DEV_IDE=y # @@ -585,27 +620,27 @@ CONFIG_BLK_DEV_IDECS=m # IDE chipset support/bugfixes # CONFIG_IDE_GENERIC=y -CONFIG_IDE_PXA_CF=y -CONFIG_IDE_ARM=y +# CONFIG_IDE_ARM is not set # CONFIG_BLK_DEV_IDEDMA is not set -# CONFIG_IDEDMA_AUTO is not set # CONFIG_BLK_DEV_HD is not set # # SCSI device support # # CONFIG_RAID_ATTRS is not set -CONFIG_SCSI=m +CONFIG_SCSI=y +# CONFIG_SCSI_TGT is not set +# CONFIG_SCSI_NETLINK is not set CONFIG_SCSI_PROC_FS=y # # SCSI support type (disk, tape, CD-ROM) # -CONFIG_BLK_DEV_SD=m +CONFIG_BLK_DEV_SD=y # CONFIG_CHR_DEV_ST is not set # CONFIG_CHR_DEV_OSST is not set # CONFIG_BLK_DEV_SR is not set -CONFIG_CHR_DEV_SG=m +CONFIG_CHR_DEV_SG=y # CONFIG_CHR_DEV_SCH is not set # @@ -614,21 +649,23 @@ CONFIG_CHR_DEV_SG=m CONFIG_SCSI_MULTI_LUN=y # CONFIG_SCSI_CONSTANTS is not set # CONFIG_SCSI_LOGGING is not set +# CONFIG_SCSI_SCAN_ASYNC is not set # -# SCSI Transport Attributes +# SCSI Transports # # CONFIG_SCSI_SPI_ATTRS is not set # CONFIG_SCSI_FC_ATTRS is not set # CONFIG_SCSI_ISCSI_ATTRS is not set # CONFIG_SCSI_SAS_ATTRS is not set +# CONFIG_SCSI_SAS_LIBSAS is not set # # SCSI low-level drivers # # CONFIG_ISCSI_TCP is not set -# CONFIG_SCSI_SATA is not set # CONFIG_SCSI_DEBUG is not set +# CONFIG_SCSI_ESP_CORE is not set # # PCMCIA SCSI adapter support @@ -640,6 +677,14 @@ CONFIG_SCSI_MULTI_LUN=y # CONFIG_PCMCIA_SYM53C500 is not set # +# Serial ATA (prod) and Parallel ATA (experimental) drivers +# +CONFIG_ATA=m +# CONFIG_ATA_NONSTANDARD is not set +CONFIG_PATA_PCMCIA=m +CONFIG_PATA_PLATFORM=m + +# # Multi-device support (RAID and LVM) # # CONFIG_MD is not set @@ -675,10 +720,14 @@ CONFIG_PHYLIB=y # MII PHY device drivers # # CONFIG_MARVELL_PHY is not set -CONFIG_DAVICOM_PHY=y +# CONFIG_DAVICOM_PHY is not set # CONFIG_QSEMI_PHY is not set # CONFIG_LXT_PHY is not set # CONFIG_CICADA_PHY is not set +# CONFIG_VITESSE_PHY is not set +# CONFIG_SMSC_PHY is not set +# CONFIG_BROADCOM_PHY is not set +# CONFIG_FIXED_PHY is not set # # Ethernet (10 or 100Mbit) @@ -687,6 +736,7 @@ CONFIG_NET_ETHERNET=y CONFIG_MII=y # CONFIG_SMC91X is not set CONFIG_DM9000=y +# CONFIG_SMC911X is not set # # Ethernet (1000 Mbit) @@ -701,41 +751,23 @@ CONFIG_DM9000=y # # -# Wireless LAN (non-hamradio) -# -CONFIG_NET_RADIO=y -# CONFIG_NET_WIRELESS_RTNETLINK is not set - -# -# Obsolete Wireless cards support (pre-802.11) -# -# CONFIG_STRIP is not set -# CONFIG_PCMCIA_WAVELAN is not set -# CONFIG_PCMCIA_NETWAVE is not set - -# -# Wireless 802.11 Frequency Hopping cards support +# Wireless LAN # +# CONFIG_WLAN_PRE80211 is not set +CONFIG_WLAN_80211=y # CONFIG_PCMCIA_RAYCS is not set - -# -# Wireless 802.11b ISA/PCI cards support -# -CONFIG_HERMES=m +CONFIG_HERMES=y # CONFIG_ATMEL is not set - -# -# Wireless 802.11b Pcmcia/Cardbus cards support -# -CONFIG_PCMCIA_HERMES=m -# CONFIG_PCMCIA_SPECTRUM is not set -CONFIG_AIRO_CS=m +CONFIG_PCMCIA_HERMES=y +CONFIG_PCMCIA_SPECTRUM=y +# CONFIG_AIRO_CS is not set # CONFIG_PCMCIA_WL3501 is not set -CONFIG_HOSTAP=m +# CONFIG_USB_ZD1201 is not set +CONFIG_HOSTAP=y CONFIG_HOSTAP_FIRMWARE=y CONFIG_HOSTAP_FIRMWARE_NVRAM=y -CONFIG_HOSTAP_CS=m -CONFIG_NET_WIRELESS=y +CONFIG_HOSTAP_CS=y +# CONFIG_ZD1211RW is not set # # PCMCIA network device support @@ -756,6 +788,7 @@ CONFIG_PPP_BSDCOMP=m CONFIG_PPP_MPPE=m # CONFIG_PPPOE is not set # CONFIG_SLIP is not set +CONFIG_SLHC=m # CONFIG_SHAPER is not set # CONFIG_NETCONSOLE is not set # CONFIG_NETPOLL is not set @@ -770,6 +803,7 @@ CONFIG_PPP_MPPE=m # Input device support # CONFIG_INPUT=y +# CONFIG_INPUT_FF_MEMLESS is not set # # Userland interfaces @@ -789,22 +823,27 @@ CONFIG_INPUT_EVDEV=y # Input Device Drivers # CONFIG_INPUT_KEYBOARD=y -CONFIG_KEYBOARD_ATKBD=y +CONFIG_KEYBOARD_ATKBD=m # CONFIG_KEYBOARD_SUNKBD is not set # CONFIG_KEYBOARD_LKKBD is not set # CONFIG_KEYBOARD_XTKBD is not set # CONFIG_KEYBOARD_NEWTON is not set +# CONFIG_KEYBOARD_STOWAWAY is not set +# CONFIG_KEYBOARD_GPIO is not set CONFIG_INPUT_MOUSE=y # CONFIG_MOUSE_PS2 is not set -CONFIG_MOUSE_SERIAL=y +CONFIG_MOUSE_SERIAL=m # CONFIG_MOUSE_VSXXXAA is not set # CONFIG_INPUT_JOYSTICK is not set CONFIG_INPUT_TOUCHSCREEN=y -# CONFIG_TOUCHSCREEN_ADS7846 is not set # CONFIG_TOUCHSCREEN_GUNZE is not set # CONFIG_TOUCHSCREEN_ELO is not set # CONFIG_TOUCHSCREEN_MTOUCH is not set # CONFIG_TOUCHSCREEN_MK712 is not set +# CONFIG_TOUCHSCREEN_PENMOUNT is not set +# CONFIG_TOUCHSCREEN_TOUCHRIGHT is not set +# CONFIG_TOUCHSCREEN_TOUCHWIN is not set +CONFIG_TOUCHSCREEN_UCB1400=y CONFIG_INPUT_MISC=y CONFIG_INPUT_UINPUT=m @@ -823,6 +862,7 @@ CONFIG_SERIO_LIBPS2=y CONFIG_VT=y CONFIG_VT_CONSOLE=y CONFIG_HW_CONSOLE=y +# CONFIG_VT_HW_CONSOLE_BINDING is not set # CONFIG_SERIAL_NONSTANDARD is not set # @@ -862,15 +902,12 @@ CONFIG_SA1100_WATCHDOG=y # USB-based Watchdog Cards # # CONFIG_USBPCWATCHDOG is not set +CONFIG_HW_RANDOM=y # CONFIG_NVRAM is not set # CONFIG_DTLK is not set # CONFIG_R3964 is not set # -# Ftape, the floppy tape device driver -# - -# # PCMCIA character devices # # CONFIG_SYNCLINK_CS is not set @@ -882,7 +919,6 @@ CONFIG_SA1100_WATCHDOG=y # TPM devices # # CONFIG_TCG_TPM is not set -# CONFIG_TELCLOCK is not set # # I2C support @@ -902,6 +938,7 @@ CONFIG_I2C_CHARDEV=y # CONFIG_I2C_PXA=y CONFIG_I2C_PXA_SLAVE=y +# CONFIG_I2C_OCORES is not set # CONFIG_I2C_PARPORT_LIGHT is not set # CONFIG_I2C_STUB is not set # CONFIG_I2C_PCA_ISA is not set @@ -911,7 +948,7 @@ CONFIG_I2C_PXA_SLAVE=y # # CONFIG_SENSORS_DS1337 is not set # CONFIG_SENSORS_DS1374 is not set -CONFIG_SENSORS_EEPROM=m +# CONFIG_SENSORS_EEPROM is not set # CONFIG_SENSORS_PCF8574 is not set # CONFIG_SENSORS_PCA9539 is not set # CONFIG_SENSORS_PCF8591 is not set @@ -924,18 +961,8 @@ CONFIG_SENSORS_EEPROM=m # # SPI support # -CONFIG_SPI=y -CONFIG_SPI_MASTER=y - -# -# SPI Master Controller Drivers -# -# CONFIG_SPI_BITBANG is not set -CONFIG_SPI_PXA2XX=m - -# -# SPI Protocol Masters -# +# CONFIG_SPI is not set +# CONFIG_SPI_MASTER is not set # # Dallas's 1-wire bus @@ -947,9 +974,11 @@ CONFIG_SPI_PXA2XX=m # CONFIG_HWMON=y # CONFIG_HWMON_VID is not set +# CONFIG_SENSORS_ABITUGURU is not set # CONFIG_SENSORS_ADM1021 is not set # CONFIG_SENSORS_ADM1025 is not set # CONFIG_SENSORS_ADM1026 is not set +# CONFIG_SENSORS_ADM1029 is not set # CONFIG_SENSORS_ADM1031 is not set # CONFIG_SENSORS_ADM9240 is not set # CONFIG_SENSORS_ASB100 is not set @@ -973,10 +1002,15 @@ CONFIG_HWMON=y # CONFIG_SENSORS_LM92 is not set # CONFIG_SENSORS_MAX1619 is not set # CONFIG_SENSORS_PC87360 is not set +# CONFIG_SENSORS_PC87427 is not set # CONFIG_SENSORS_SMSC47M1 is not set +# CONFIG_SENSORS_SMSC47M192 is not set # CONFIG_SENSORS_SMSC47B397 is not set +# CONFIG_SENSORS_VT1211 is not set # CONFIG_SENSORS_W83781D is not set +# CONFIG_SENSORS_W83791D is not set # CONFIG_SENSORS_W83792D is not set +# CONFIG_SENSORS_W83793 is not set # CONFIG_SENSORS_W83L785TS is not set # CONFIG_SENSORS_W83627HF is not set # CONFIG_SENSORS_W83627EHF is not set @@ -987,16 +1021,15 @@ CONFIG_HWMON=y # # -# Multimedia Capabilities Port drivers +# Multifunction device drivers # -CONFIG_UCB1400=y -CONFIG_UCB1400_TS=y +# CONFIG_MFD_SM501 is not set # # LED devices # CONFIG_NEW_LEDS=y -CONFIG_LEDS_CLASS=y +# CONFIG_LEDS_CLASS is not set # # LED drivers @@ -1007,13 +1040,13 @@ CONFIG_LEDS_CLASS=y # CONFIG_LEDS_TRIGGERS=y CONFIG_LEDS_TRIGGER_TIMER=y -CONFIG_LEDS_TRIGGER_IDE_DISK=y +# CONFIG_LEDS_TRIGGER_IDE_DISK is not set +CONFIG_LEDS_TRIGGER_HEARTBEAT=y # # Multimedia devices # # CONFIG_VIDEO_DEV is not set -CONFIG_VIDEO_V4L2=y # # Digital Video Broadcasting Devices @@ -1024,17 +1057,28 @@ CONFIG_VIDEO_V4L2=y # # Graphics support # +CONFIG_BACKLIGHT_LCD_SUPPORT=y +CONFIG_BACKLIGHT_CLASS_DEVICE=y +CONFIG_LCD_CLASS_DEVICE=y CONFIG_FB=y +CONFIG_FIRMWARE_EDID=y +# CONFIG_FB_DDC is not set CONFIG_FB_CFB_FILLRECT=y CONFIG_FB_CFB_COPYAREA=y CONFIG_FB_CFB_IMAGEBLIT=y +# CONFIG_FB_SVGALIB is not set # CONFIG_FB_MACMODES is not set -CONFIG_FB_FIRMWARE_EDID=y +# CONFIG_FB_BACKLIGHT is not set # CONFIG_FB_MODE_HELPERS is not set # CONFIG_FB_TILEBLITTING is not set + +# +# Frame buffer hardware drivers +# # CONFIG_FB_S1D13XXX is not set CONFIG_FB_PXA=y # CONFIG_FB_PXA_PARAMETERS is not set +# CONFIG_FB_MBX is not set # CONFIG_FB_VIRTUAL is not set # @@ -1063,11 +1107,6 @@ CONFIG_LOGO=y CONFIG_LOGO_LINUX_MONO=y CONFIG_LOGO_LINUX_VGA16=y CONFIG_LOGO_LINUX_CLUT224=y -CONFIG_BACKLIGHT_LCD_SUPPORT=y -CONFIG_BACKLIGHT_CLASS_DEVICE=y -CONFIG_BACKLIGHT_DEVICE=y -CONFIG_LCD_CLASS_DEVICE=y -CONFIG_LCD_DEVICE=y # # Sound @@ -1082,7 +1121,7 @@ CONFIG_SND_TIMER=y CONFIG_SND_PCM=y CONFIG_SND_HWDEP=m CONFIG_SND_RAWMIDI=m -CONFIG_SND_SEQUENCER=m +CONFIG_SND_SEQUENCER=y # CONFIG_SND_SEQ_DUMMY is not set CONFIG_SND_OSSEMUL=y CONFIG_SND_MIXER_OSS=y @@ -1093,13 +1132,14 @@ CONFIG_SND_PCM_OSS_PLUGINS=y CONFIG_SND_SUPPORT_OLD_API=y CONFIG_SND_VERBOSE_PROCFS=y CONFIG_SND_VERBOSE_PRINTK=y -# CONFIG_SND_DEBUG is not set +CONFIG_SND_DEBUG=y +CONFIG_SND_DEBUG_DETECT=y +# CONFIG_SND_PCM_XRUN_DEBUG is not set # # Generic devices # CONFIG_SND_AC97_CODEC=y -CONFIG_SND_AC97_BUS=y # CONFIG_SND_DUMMY is not set # CONFIG_SND_VIRMIDI is not set # CONFIG_SND_MTPAV is not set @@ -1124,9 +1164,32 @@ CONFIG_SND_USB_AUDIO=m # CONFIG_SND_PDAUDIOCF is not set # +# SoC audio support +# +# CONFIG_SND_SOC is not set + +# # Open Sound System # # CONFIG_SOUND_PRIME is not set +CONFIG_AC97_BUS=y + +# +# HID Devices +# +CONFIG_HID=y +# CONFIG_HID_DEBUG is not set + +# +# USB Input Devices +# +# CONFIG_USB_HID is not set + +# +# USB HID Boot Protocol drivers +# +# CONFIG_USB_KBD is not set +# CONFIG_USB_MOUSE is not set # # USB support @@ -1141,7 +1204,7 @@ CONFIG_USB=y # Miscellaneous USB options # CONFIG_USB_DEVICEFS=y -# CONFIG_USB_BANDWIDTH is not set +# CONFIG_USB_DEVICE_CLASS is not set # CONFIG_USB_DYNAMIC_MINORS is not set # CONFIG_USB_SUSPEND is not set # CONFIG_USB_OTG is not set @@ -1151,7 +1214,8 @@ CONFIG_USB_DEVICEFS=y # # CONFIG_USB_ISP116X_HCD is not set CONFIG_USB_OHCI_HCD=y -# CONFIG_USB_OHCI_BIG_ENDIAN is not set +# CONFIG_USB_OHCI_BIG_ENDIAN_DESC is not set +# CONFIG_USB_OHCI_BIG_ENDIAN_MMIO is not set CONFIG_USB_OHCI_LITTLE_ENDIAN=y # CONFIG_USB_SL811_HCD is not set @@ -1179,38 +1243,25 @@ CONFIG_USB_STORAGE=m # CONFIG_USB_STORAGE_SDDR55 is not set # CONFIG_USB_STORAGE_JUMPSHOT is not set # CONFIG_USB_STORAGE_ALAUDA is not set +# CONFIG_USB_STORAGE_KARMA is not set # CONFIG_USB_LIBUSUAL is not set # # USB Input Devices # -CONFIG_USB_HID=m -CONFIG_USB_HIDINPUT=y -# CONFIG_USB_HIDINPUT_POWERBOOK is not set -# CONFIG_HID_FF is not set -# CONFIG_USB_HIDDEV is not set - -# -# USB HID Boot Protocol drivers -# -# CONFIG_USB_KBD is not set -# CONFIG_USB_MOUSE is not set # CONFIG_USB_AIPTEK is not set # CONFIG_USB_WACOM is not set # CONFIG_USB_ACECAD is not set # CONFIG_USB_KBTAB is not set # CONFIG_USB_POWERMATE is not set -CONFIG_USB_TOUCHSCREEN=m -# CONFIG_USB_TOUCHSCREEN_EGALAX is not set -# CONFIG_USB_TOUCHSCREEN_PANJIT is not set -# CONFIG_USB_TOUCHSCREEN_3M is not set -# CONFIG_USB_TOUCHSCREEN_ITM is not set +# CONFIG_USB_TOUCHSCREEN is not set # CONFIG_USB_YEALINK is not set # CONFIG_USB_XPAD is not set # CONFIG_USB_ATI_REMOTE is not set # CONFIG_USB_ATI_REMOTE2 is not set # CONFIG_USB_KEYSPAN_REMOTE is not set # CONFIG_USB_APPLETOUCH is not set +# CONFIG_USB_GTCO is not set # # USB Imaging devices @@ -1225,9 +1276,9 @@ CONFIG_USB_TOUCHSCREEN=m # CONFIG_USB_KAWETH is not set # CONFIG_USB_PEGASUS is not set # CONFIG_USB_RTL8150 is not set +# CONFIG_USB_USBNET_MII is not set # CONFIG_USB_USBNET is not set -# CONFIG_USB_ZD1201 is not set -CONFIG_USB_MON=y +# CONFIG_USB_MON is not set # # USB port drivers @@ -1236,23 +1287,66 @@ CONFIG_USB_MON=y # # USB Serial Converter support # -# CONFIG_USB_SERIAL is not set +CONFIG_USB_SERIAL=m +# CONFIG_USB_SERIAL_GENERIC is not set +# CONFIG_USB_SERIAL_AIRCABLE is not set +# CONFIG_USB_SERIAL_AIRPRIME is not set +# CONFIG_USB_SERIAL_ARK3116 is not set +# CONFIG_USB_SERIAL_BELKIN is not set +# CONFIG_USB_SERIAL_WHITEHEAT is not set +# CONFIG_USB_SERIAL_DIGI_ACCELEPORT is not set +# CONFIG_USB_SERIAL_CP2101 is not set +# CONFIG_USB_SERIAL_CYPRESS_M8 is not set +# CONFIG_USB_SERIAL_EMPEG is not set +# CONFIG_USB_SERIAL_FTDI_SIO is not set +# CONFIG_USB_SERIAL_FUNSOFT is not set +# CONFIG_USB_SERIAL_VISOR is not set +# CONFIG_USB_SERIAL_IPAQ is not set +# CONFIG_USB_SERIAL_IR is not set +# CONFIG_USB_SERIAL_EDGEPORT is not set +# CONFIG_USB_SERIAL_EDGEPORT_TI is not set +# CONFIG_USB_SERIAL_GARMIN is not set +# CONFIG_USB_SERIAL_IPW is not set +# CONFIG_USB_SERIAL_KEYSPAN_PDA is not set +# CONFIG_USB_SERIAL_KEYSPAN is not set +# CONFIG_USB_SERIAL_KLSI is not set +# CONFIG_USB_SERIAL_KOBIL_SCT is not set +# CONFIG_USB_SERIAL_MCT_U232 is not set +# CONFIG_USB_SERIAL_MOS7720 is not set +# CONFIG_USB_SERIAL_MOS7840 is not set +# CONFIG_USB_SERIAL_NAVMAN is not set +# CONFIG_USB_SERIAL_PL2303 is not set +# CONFIG_USB_SERIAL_HP4X is not set +# CONFIG_USB_SERIAL_SAFE is not set +# CONFIG_USB_SERIAL_SIERRAWIRELESS is not set +# CONFIG_USB_SERIAL_TI is not set +# CONFIG_USB_SERIAL_CYBERJACK is not set +# CONFIG_USB_SERIAL_XIRCOM is not set +# CONFIG_USB_SERIAL_OPTION is not set +# CONFIG_USB_SERIAL_OMNINET is not set +# CONFIG_USB_SERIAL_DEBUG is not set # # USB Miscellaneous drivers # # CONFIG_USB_EMI62 is not set # CONFIG_USB_EMI26 is not set +# CONFIG_USB_ADUTUX is not set # CONFIG_USB_AUERSWALD is not set # CONFIG_USB_RIO500 is not set # CONFIG_USB_LEGOTOWER is not set # CONFIG_USB_LCD is not set +# CONFIG_USB_BERRY_CHARGE is not set # CONFIG_USB_LED is not set +# CONFIG_USB_CYPRESS_CY7C63 is not set # CONFIG_USB_CYTHERM is not set -# CONFIG_USB_PHIDGETKIT is not set -# CONFIG_USB_PHIDGETSERVO is not set +# CONFIG_USB_PHIDGET is not set # CONFIG_USB_IDMOUSE is not set +# CONFIG_USB_FTDI_ELAN is not set +# CONFIG_USB_APPLEDISPLAY is not set # CONFIG_USB_LD is not set +# CONFIG_USB_TRANCEVIBRATOR is not set +# CONFIG_USB_IOWARRIOR is not set # CONFIG_USB_TEST is not set # @@ -1262,9 +1356,10 @@ CONFIG_USB_MON=y # # USB Gadget Support # -CONFIG_USB_GADGET=y +CONFIG_USB_GADGET=m # CONFIG_USB_GADGET_DEBUG_FILES is not set CONFIG_USB_GADGET_SELECTED=y +# CONFIG_USB_GADGET_FSL_USB2 is not set # CONFIG_USB_GADGET_NET2280 is not set # CONFIG_USB_GADGET_PXA2XX is not set # CONFIG_USB_GADGET_GOKU is not set @@ -1272,15 +1367,14 @@ CONFIG_USB_GADGET_SELECTED=y # CONFIG_USB_GADGET_OMAP is not set # CONFIG_USB_GADGET_AT91 is not set CONFIG_USB_GADGET_DUMMY_HCD=y -CONFIG_USB_DUMMY_HCD=y +CONFIG_USB_DUMMY_HCD=m CONFIG_USB_GADGET_DUALSPEED=y # CONFIG_USB_ZERO is not set -CONFIG_USB_ETH=m -CONFIG_USB_ETH_RNDIS=y -CONFIG_USB_GADGETFS=m -CONFIG_USB_FILE_STORAGE=m -# CONFIG_USB_FILE_STORAGE_TEST is not set -CONFIG_USB_G_SERIAL=m +# CONFIG_USB_ETH is not set +# CONFIG_USB_GADGETFS is not set +# CONFIG_USB_FILE_STORAGE is not set +# CONFIG_USB_G_SERIAL is not set +# CONFIG_USB_MIDI_GADGET is not set # # MMC/SD Card support @@ -1295,8 +1389,8 @@ CONFIG_MMC_PXA=y # CONFIG_RTC_LIB=y CONFIG_RTC_CLASS=y -CONFIG_RTC_HCTOSYS=y -CONFIG_RTC_HCTOSYS_DEVICE="rtc0" +# CONFIG_RTC_HCTOSYS is not set +# CONFIG_RTC_DEBUG is not set # # RTC interfaces @@ -1304,17 +1398,25 @@ CONFIG_RTC_HCTOSYS_DEVICE="rtc0" CONFIG_RTC_INTF_SYSFS=y CONFIG_RTC_INTF_PROC=y CONFIG_RTC_INTF_DEV=y +# CONFIG_RTC_INTF_DEV_UIE_EMUL is not set # # RTC drivers # +# CONFIG_RTC_DRV_CMOS is not set # CONFIG_RTC_DRV_X1205 is not set +# CONFIG_RTC_DRV_DS1307 is not set +# CONFIG_RTC_DRV_DS1553 is not set +# CONFIG_RTC_DRV_ISL1208 is not set # CONFIG_RTC_DRV_DS1672 is not set +# CONFIG_RTC_DRV_DS1742 is not set # CONFIG_RTC_DRV_PCF8563 is not set +CONFIG_RTC_DRV_PCF8583=m # CONFIG_RTC_DRV_RS5C372 is not set # CONFIG_RTC_DRV_M48T86 is not set CONFIG_RTC_DRV_SA1100=y # CONFIG_RTC_DRV_TEST is not set +# CONFIG_RTC_DRV_V3020 is not set # # File systems @@ -1328,6 +1430,7 @@ CONFIG_EXT3_FS=y CONFIG_EXT3_FS_XATTR=y CONFIG_EXT3_FS_POSIX_ACL=y CONFIG_EXT3_FS_SECURITY=y +# CONFIG_EXT4DEV_FS is not set CONFIG_JBD=y # CONFIG_JBD_DEBUG is not set CONFIG_FS_MBCACHE=y @@ -1335,10 +1438,12 @@ CONFIG_FS_MBCACHE=y # CONFIG_JFS_FS is not set CONFIG_FS_POSIX_ACL=y # CONFIG_XFS_FS is not set +# CONFIG_GFS2_FS is not set # CONFIG_OCFS2_FS is not set # CONFIG_MINIX_FS is not set # CONFIG_ROMFS_FS is not set CONFIG_INOTIFY=y +CONFIG_INOTIFY_USER=y # CONFIG_QUOTA is not set CONFIG_DNOTIFY=y # CONFIG_AUTOFS_FS is not set @@ -1365,8 +1470,10 @@ CONFIG_FAT_DEFAULT_IOCHARSET="iso8859-15" # Pseudo filesystems # CONFIG_PROC_FS=y +CONFIG_PROC_SYSCTL=y CONFIG_SYSFS=y CONFIG_TMPFS=y +# CONFIG_TMPFS_POSIX_ACL is not set # CONFIG_HUGETLB_PAGE is not set CONFIG_RAMFS=y # CONFIG_CONFIGFS_FS is not set @@ -1376,18 +1483,17 @@ CONFIG_RAMFS=y # # CONFIG_ADFS_FS is not set # CONFIG_AFFS_FS is not set +# CONFIG_ECRYPT_FS is not set # CONFIG_HFS_FS is not set # CONFIG_HFSPLUS_FS is not set # CONFIG_BEFS_FS is not set # CONFIG_BFS_FS is not set # CONFIG_EFS_FS is not set -CONFIG_JFFS_FS=y -CONFIG_JFFS_FS_VERBOSE=0 -CONFIG_JFFS_PROC_FS=y CONFIG_JFFS2_FS=y CONFIG_JFFS2_FS_DEBUG=0 CONFIG_JFFS2_FS_WRITEBUFFER=y # CONFIG_JFFS2_SUMMARY is not set +# CONFIG_JFFS2_FS_XATTR is not set CONFIG_JFFS2_COMPRESSION_OPTIONS=y CONFIG_JFFS2_ZLIB=y CONFIG_JFFS2_RTIME=y @@ -1407,20 +1513,18 @@ CONFIG_JFFS2_CMODE_PRIORITY=y # CONFIG_NFS_FS=y CONFIG_NFS_V3=y -CONFIG_NFS_V3_ACL=y +# CONFIG_NFS_V3_ACL is not set CONFIG_NFS_V4=y # CONFIG_NFS_DIRECTIO is not set CONFIG_NFSD=y -CONFIG_NFSD_V2_ACL=y CONFIG_NFSD_V3=y -CONFIG_NFSD_V3_ACL=y +# CONFIG_NFSD_V3_ACL is not set CONFIG_NFSD_V4=y CONFIG_NFSD_TCP=y CONFIG_ROOT_NFS=y CONFIG_LOCKD=y CONFIG_LOCKD_V4=y CONFIG_EXPORTFS=y -CONFIG_NFS_ACL_SUPPORT=y CONFIG_NFS_COMMON=y CONFIG_SUNRPC=y CONFIG_SUNRPC_GSS=y @@ -1430,7 +1534,9 @@ CONFIG_SMB_FS=m # CONFIG_SMB_NLS_DEFAULT is not set CONFIG_CIFS=m # CONFIG_CIFS_STATS is not set +# CONFIG_CIFS_WEAK_PW_HASH is not set # CONFIG_CIFS_XATTR is not set +# CONFIG_CIFS_DEBUG2 is not set # CONFIG_CIFS_EXPERIMENTAL is not set # CONFIG_NCP_FS is not set # CONFIG_CODA_FS is not set @@ -1504,22 +1610,28 @@ CONFIG_NLS_ISO8859_15=m CONFIG_NLS_UTF8=m # +# Distributed Lock Manager +# +# CONFIG_DLM is not set + +# # Profiling support # -CONFIG_PROFILING=y -CONFIG_OPROFILE=y +# CONFIG_PROFILING is not set # # Kernel hacking # # CONFIG_PRINTK_TIME is not set +CONFIG_ENABLE_MUST_CHECK=y CONFIG_MAGIC_SYSRQ=y +# CONFIG_UNUSED_SYMBOLS is not set +CONFIG_DEBUG_FS=y +# CONFIG_HEADERS_CHECK is not set # CONFIG_DEBUG_KERNEL is not set CONFIG_LOG_BUF_SHIFT=14 # CONFIG_DEBUG_BUGVERBOSE is not set -# CONFIG_DEBUG_FS is not set CONFIG_FRAME_POINTER=y -# CONFIG_UNWIND_INFO is not set CONFIG_DEBUG_USER=y # @@ -1531,22 +1643,31 @@ CONFIG_SECURITY=y # CONFIG_SECURITY_NETWORK is not set CONFIG_SECURITY_CAPABILITIES=y # CONFIG_SECURITY_ROOTPLUG is not set -# CONFIG_SECURITY_SECLVL is not set # # Cryptographic options # CONFIG_CRYPTO=y +CONFIG_CRYPTO_ALGAPI=y +CONFIG_CRYPTO_BLKCIPHER=y +CONFIG_CRYPTO_MANAGER=y # CONFIG_CRYPTO_HMAC is not set +# CONFIG_CRYPTO_XCBC is not set # CONFIG_CRYPTO_NULL is not set -CONFIG_CRYPTO_MD4=y +# CONFIG_CRYPTO_MD4 is not set CONFIG_CRYPTO_MD5=y CONFIG_CRYPTO_SHA1=m CONFIG_CRYPTO_SHA256=m CONFIG_CRYPTO_SHA512=m # CONFIG_CRYPTO_WP512 is not set # CONFIG_CRYPTO_TGR192 is not set +# CONFIG_CRYPTO_GF128MUL is not set +CONFIG_CRYPTO_ECB=y +CONFIG_CRYPTO_CBC=y +CONFIG_CRYPTO_PCBC=m +# CONFIG_CRYPTO_LRW is not set CONFIG_CRYPTO_DES=y +# CONFIG_CRYPTO_FCRYPT is not set # CONFIG_CRYPTO_BLOWFISH is not set # CONFIG_CRYPTO_TWOFISH is not set # CONFIG_CRYPTO_SERPENT is not set @@ -1554,12 +1675,13 @@ CONFIG_CRYPTO_AES=m # CONFIG_CRYPTO_CAST5 is not set # CONFIG_CRYPTO_CAST6 is not set # CONFIG_CRYPTO_TEA is not set -CONFIG_CRYPTO_ARC4=m +CONFIG_CRYPTO_ARC4=y # CONFIG_CRYPTO_KHAZAD is not set # CONFIG_CRYPTO_ANUBIS is not set CONFIG_CRYPTO_DEFLATE=m CONFIG_CRYPTO_MICHAEL_MIC=m CONFIG_CRYPTO_CRC32C=y +# CONFIG_CRYPTO_CAMELLIA is not set # CONFIG_CRYPTO_TEST is not set # @@ -1569,6 +1691,7 @@ CONFIG_CRYPTO_CRC32C=y # # Library routines # +CONFIG_BITREVERSE=y CONFIG_CRC_CCITT=y CONFIG_CRC16=y CONFIG_CRC32=y @@ -1577,3 +1700,6 @@ CONFIG_ZLIB_INFLATE=y CONFIG_ZLIB_DEFLATE=y CONFIG_REED_SOLOMON=y CONFIG_REED_SOLOMON_DEC16=y +CONFIG_PLIST=y +CONFIG_HAS_IOMEM=y +CONFIG_HAS_IOPORT=y diff --git a/arch/arm/kernel/ecard.c b/arch/arm/kernel/ecard.c index bdbd7da9928..f56d48c451e 100644 --- a/arch/arm/kernel/ecard.c +++ b/arch/arm/kernel/ecard.c @@ -41,11 +41,11 @@ #include <linux/init.h> #include <linux/mutex.h> #include <linux/kthread.h> +#include <linux/io.h> #include <asm/dma.h> #include <asm/ecard.h> #include <asm/hardware.h> -#include <asm/io.h> #include <asm/irq.h> #include <asm/mmu_context.h> #include <asm/mach/irq.h> @@ -958,6 +958,31 @@ void ecard_release_resources(struct expansion_card *ec) } EXPORT_SYMBOL(ecard_release_resources); +void ecard_setirq(struct expansion_card *ec, const struct expansion_card_ops *ops, void *irq_data) +{ + ec->irq_data = irq_data; + barrier(); + ec->ops = ops; +} +EXPORT_SYMBOL(ecard_setirq); + +void __iomem *ecardm_iomap(struct expansion_card *ec, unsigned int res, + unsigned long offset, unsigned long maxsize) +{ + unsigned long start = ecard_resource_start(ec, res); + unsigned long end = ecard_resource_end(ec, res); + + if (offset > (end - start)) + return NULL; + + start += offset; + if (maxsize && end - start > maxsize) + end = start + maxsize; + + return devm_ioremap(&ec->dev, start, end - start); +} +EXPORT_SYMBOL(ecardm_iomap); + /* * Probe for an expansion card. * @@ -1133,6 +1158,14 @@ static int ecard_drv_remove(struct device *dev) drv->remove(ec); ecard_release(ec); + /* + * Restore the default operations. We ensure that the + * ops are set before we change the data. + */ + ec->ops = &ecard_default_ops; + barrier(); + ec->irq_data = NULL; + return 0; } diff --git a/arch/arm/kernel/time.c b/arch/arm/kernel/time.c index d0540e4eaf5..1533d3ecd7a 100644 --- a/arch/arm/kernel/time.c +++ b/arch/arm/kernel/time.c @@ -512,7 +512,7 @@ void __init time_init(void) #ifdef CONFIG_NO_IDLE_HZ if (system_timer->dyn_tick) - system_timer->dyn_tick->lock = SPIN_LOCK_UNLOCKED; + spin_lock_init(&system_timer->dyn_tick->lock); #endif } diff --git a/arch/arm/mach-at91/Kconfig b/arch/arm/mach-at91/Kconfig index 018d637f87f..a31157f1655 100644 --- a/arch/arm/mach-at91/Kconfig +++ b/arch/arm/mach-at91/Kconfig @@ -17,6 +17,9 @@ config ARCH_AT91SAM9261 config ARCH_AT91SAM9263 bool "AT91SAM9263" +config ARCH_AT91SAM9RL + bool "AT91SAM9RL" + endchoice # ---------------------------------------------------------- @@ -152,6 +155,20 @@ endif # ---------------------------------------------------------- +if ARCH_AT91SAM9RL + +comment "AT91SAM9RL Board Type" + +config MACH_AT91SAM9RLEK + bool "Atmel AT91SAM9RL-EK Evaluation Kit" + depends on ARCH_AT91SAM9RL + help + Select this if you are using Atmel's AT91SAM9RL-EK Evaluation Kit. + +endif + +# ---------------------------------------------------------- + comment "AT91 Board Options" config MTD_AT91_DATAFLASH_CARD diff --git a/arch/arm/mach-at91/Makefile b/arch/arm/mach-at91/Makefile index cd1bc541f28..a4d80eb056e 100644 --- a/arch/arm/mach-at91/Makefile +++ b/arch/arm/mach-at91/Makefile @@ -14,6 +14,7 @@ obj-$(CONFIG_ARCH_AT91RM9200) += at91rm9200.o at91rm9200_time.o at91rm9200_devic obj-$(CONFIG_ARCH_AT91SAM9260) += at91sam9260.o at91sam926x_time.o at91sam9260_devices.o obj-$(CONFIG_ARCH_AT91SAM9261) += at91sam9261.o at91sam926x_time.o at91sam9261_devices.o obj-$(CONFIG_ARCH_AT91SAM9263) += at91sam9263.o at91sam926x_time.o at91sam9263_devices.o +obj-$(CONFIG_ARCH_AT91SAM9RL) += at91sam9rl.o at91sam926x_time.o at91sam9rl_devices.o # AT91RM9200 board-specific support obj-$(CONFIG_MACH_ONEARM) += board-1arm.o @@ -36,6 +37,9 @@ obj-$(CONFIG_MACH_AT91SAM9261EK) += board-sam9261ek.o # AT91SAM9263 board-specific support obj-$(CONFIG_MACH_AT91SAM9263EK) += board-sam9263ek.o +# AT91SAM9RL board-specific support +obj-$(CONFIG_MACH_AT91SAM9RLEK) += board-sam9rlek.o + # LEDs support led-$(CONFIG_ARCH_AT91RM9200DK) += leds.o led-$(CONFIG_MACH_AT91RM9200EK) += leds.o diff --git a/arch/arm/mach-at91/at91rm9200_devices.c b/arch/arm/mach-at91/at91rm9200_devices.c index 2624a4f22d6..70599bcf451 100644 --- a/arch/arm/mach-at91/at91rm9200_devices.c +++ b/arch/arm/mach-at91/at91rm9200_devices.c @@ -22,9 +22,6 @@ #include "generic.h" -#define SZ_512 0x00000200 -#define SZ_256 0x00000100 -#define SZ_16 0x00000010 /* -------------------------------------------------------------------- * USB Host diff --git a/arch/arm/mach-at91/at91sam9260_devices.c b/arch/arm/mach-at91/at91sam9260_devices.c index 40586e22cd3..ffd3154c1e5 100644 --- a/arch/arm/mach-at91/at91sam9260_devices.c +++ b/arch/arm/mach-at91/at91sam9260_devices.c @@ -22,9 +22,6 @@ #include "generic.h" -#define SZ_512 0x00000200 -#define SZ_256 0x00000100 -#define SZ_16 0x00000010 /* -------------------------------------------------------------------- * USB Host diff --git a/arch/arm/mach-at91/at91sam9261_devices.c b/arch/arm/mach-at91/at91sam9261_devices.c index 8e781997716..9db58da0475 100644 --- a/arch/arm/mach-at91/at91sam9261_devices.c +++ b/arch/arm/mach-at91/at91sam9261_devices.c @@ -23,9 +23,6 @@ #include "generic.h" -#define SZ_512 0x00000200 -#define SZ_256 0x00000100 -#define SZ_16 0x00000010 /* -------------------------------------------------------------------- * USB Host diff --git a/arch/arm/mach-at91/at91sam9263_devices.c b/arch/arm/mach-at91/at91sam9263_devices.c index 2b2e18a6712..635695787f9 100644 --- a/arch/arm/mach-at91/at91sam9263_devices.c +++ b/arch/arm/mach-at91/at91sam9263_devices.c @@ -22,9 +22,6 @@ #include "generic.h" -#define SZ_512 0x00000200 -#define SZ_256 0x00000100 -#define SZ_16 0x00000010 /* -------------------------------------------------------------------- * USB Host diff --git a/arch/arm/mach-at91/at91sam9rl.c b/arch/arm/mach-at91/at91sam9rl.c new file mode 100644 index 00000000000..4813a35f6cf --- /dev/null +++ b/arch/arm/mach-at91/at91sam9rl.c @@ -0,0 +1,341 @@ +/* + * arch/arm/mach-at91/at91sam9rl.c + * + * Copyright (C) 2005 SAN People + * Copyright (C) 2007 Atmel Corporation + * + * This file is subject to the terms and conditions of the GNU General Public + * License. See the file COPYING in the main directory of this archive for + * more details. + */ + +#include <linux/module.h> + +#include <asm/mach/arch.h> +#include <asm/mach/map.h> +#include <asm/arch/cpu.h> +#include <asm/arch/at91sam9rl.h> +#include <asm/arch/at91_pmc.h> +#include <asm/arch/at91_rstc.h> + +#include "generic.h" +#include "clock.h" + +static struct map_desc at91sam9rl_io_desc[] __initdata = { + { + .virtual = AT91_VA_BASE_SYS, + .pfn = __phys_to_pfn(AT91_BASE_SYS), + .length = SZ_16K, + .type = MT_DEVICE, + }, +}; + +static struct map_desc at91sam9rl_sram_desc[] __initdata = { + { + .pfn = __phys_to_pfn(AT91SAM9RL_SRAM_BASE), + .type = MT_DEVICE, + } +}; + +/* -------------------------------------------------------------------- + * Clocks + * -------------------------------------------------------------------- */ + +/* + * The peripheral clocks. + */ +static struct clk pioA_clk = { + .name = "pioA_clk", + .pmc_mask = 1 << AT91SAM9RL_ID_PIOA, + .type = CLK_TYPE_PERIPHERAL, +}; +static struct clk pioB_clk = { + .name = "pioB_clk", + .pmc_mask = 1 << AT91SAM9RL_ID_PIOB, + .type = CLK_TYPE_PERIPHERAL, +}; +static struct clk pioC_clk = { + .name = "pioC_clk", + .pmc_mask = 1 << AT91SAM9RL_ID_PIOC, + .type = CLK_TYPE_PERIPHERAL, +}; +static struct clk pioD_clk = { + .name = "pioD_clk", + .pmc_mask = 1 << AT91SAM9RL_ID_PIOD, + .type = CLK_TYPE_PERIPHERAL, +}; +static struct clk usart0_clk = { + .name = "usart0_clk", + .pmc_mask = 1 << AT91SAM9RL_ID_US0, + .type = CLK_TYPE_PERIPHERAL, +}; +static struct clk usart1_clk = { + .name = "usart1_clk", + .pmc_mask = 1 << AT91SAM9RL_ID_US1, + .type = CLK_TYPE_PERIPHERAL, +}; +static struct clk usart2_clk = { + .name = "usart2_clk", + .pmc_mask = 1 << AT91SAM9RL_ID_US2, + .type = CLK_TYPE_PERIPHERAL, +}; +static struct clk usart3_clk = { + .name = "usart3_clk", + .pmc_mask = 1 << AT91SAM9RL_ID_US3, + .type = CLK_TYPE_PERIPHERAL, +}; +static struct clk mmc_clk = { + .name = "mci_clk", + .pmc_mask = 1 << AT91SAM9RL_ID_MCI, + .type = CLK_TYPE_PERIPHERAL, +}; +static struct clk twi0_clk = { + .name = "twi0_clk", + .pmc_mask = 1 << AT91SAM9RL_ID_TWI0, + .type = CLK_TYPE_PERIPHERAL, +}; +static struct clk twi1_clk = { + .name = "twi1_clk", + .pmc_mask = 1 << AT91SAM9RL_ID_TWI1, + .type = CLK_TYPE_PERIPHERAL, +}; +static struct clk spi_clk = { + .name = "spi_clk", + .pmc_mask = 1 << AT91SAM9RL_ID_SPI, + .type = CLK_TYPE_PERIPHERAL, +}; +static struct clk ssc0_clk = { + .name = "ssc0_clk", + .pmc_mask = 1 << AT91SAM9RL_ID_SSC0, + .type = CLK_TYPE_PERIPHERAL, +}; +static struct clk ssc1_clk = { + .name = "ssc1_clk", + .pmc_mask = 1 << AT91SAM9RL_ID_SSC1, + .type = CLK_TYPE_PERIPHERAL, +}; +static struct clk tc0_clk = { + .name = "tc0_clk", + .pmc_mask = 1 << AT91SAM9RL_ID_TC0, + .type = CLK_TYPE_PERIPHERAL, +}; +static struct clk tc1_clk = { + .name = "tc1_clk", + .pmc_mask = 1 << AT91SAM9RL_ID_TC1, + .type = CLK_TYPE_PERIPHERAL, +}; +static struct clk tc2_clk = { + .name = "tc2_clk", + .pmc_mask = 1 << AT91SAM9RL_ID_TC2, + .type = CLK_TYPE_PERIPHERAL, +}; +static struct clk pwmc_clk = { + .name = "pwmc_clk", + .pmc_mask = 1 << AT91SAM9RL_ID_PWMC, + .type = CLK_TYPE_PERIPHERAL, +}; +static struct clk tsc_clk = { + .name = "tsc_clk", + .pmc_mask = 1 << AT91SAM9RL_ID_TSC, + .type = CLK_TYPE_PERIPHERAL, +}; +static struct clk dma_clk = { + .name = "dma_clk", + .pmc_mask = 1 << AT91SAM9RL_ID_DMA, + .type = CLK_TYPE_PERIPHERAL, +}; +static struct clk udphs_clk = { + .name = "udphs_clk", + .pmc_mask = 1 << AT91SAM9RL_ID_UDPHS, + .type = CLK_TYPE_PERIPHERAL, +}; +static struct clk lcdc_clk = { + .name = "lcdc_clk", + .pmc_mask = 1 << AT91SAM9RL_ID_LCDC, + .type = CLK_TYPE_PERIPHERAL, +}; +static struct clk ac97_clk = { + .name = "ac97_clk", + .pmc_mask = 1 << AT91SAM9RL_ID_AC97C, + .type = CLK_TYPE_PERIPHERAL, +}; + +static struct clk *periph_clocks[] __initdata = { + &pioA_clk, + &pioB_clk, + &pioC_clk, + &pioD_clk, + &usart0_clk, + &usart1_clk, + &usart2_clk, + &usart3_clk, + &mmc_clk, + &twi0_clk, + &twi1_clk, + &spi_clk, + &ssc0_clk, + &ssc1_clk, + &tc0_clk, + &tc1_clk, + &tc2_clk, + &pwmc_clk, + &tsc_clk, + &dma_clk, + &udphs_clk, + &lcdc_clk, + &ac97_clk, + // irq0 +}; + +/* + * The two programmable clocks. + * You must configure pin multiplexing to bring these signals out. + */ +static struct clk pck0 = { + .name = "pck0", + .pmc_mask = AT91_PMC_PCK0, + .type = CLK_TYPE_PROGRAMMABLE, + .id = 0, +}; +static struct clk pck1 = { + .name = "pck1", + .pmc_mask = AT91_PMC_PCK1, + .type = CLK_TYPE_PROGRAMMABLE, + .id = 1, +}; + +static void __init at91sam9rl_register_clocks(void) +{ + int i; + + for (i = 0; i < ARRAY_SIZE(periph_clocks); i++) + clk_register(periph_clocks[i]); + + clk_register(&pck0); + clk_register(&pck1); +} + +/* -------------------------------------------------------------------- + * GPIO + * -------------------------------------------------------------------- */ + +static struct at91_gpio_bank at91sam9rl_gpio[] = { + { + .id = AT91SAM9RL_ID_PIOA, + .offset = AT91_PIOA, + .clock = &pioA_clk, + }, { + .id = AT91SAM9RL_ID_PIOB, + .offset = AT91_PIOB, + .clock = &pioB_clk, + }, { + .id = AT91SAM9RL_ID_PIOC, + .offset = AT91_PIOC, + .clock = &pioC_clk, + }, { + .id = AT91SAM9RL_ID_PIOD, + .offset = AT91_PIOD, + .clock = &pioD_clk, + } +}; + +static void at91sam9rl_reset(void) +{ + at91_sys_write(AT91_RSTC_CR, AT91_RSTC_KEY | AT91_RSTC_PROCRST | AT91_RSTC_PERRST); +} + + +/* -------------------------------------------------------------------- + * AT91SAM9RL processor initialization + * -------------------------------------------------------------------- */ + +void __init at91sam9rl_initialize(unsigned long main_clock) +{ + unsigned long cidr, sram_size; + + /* Map peripherals */ + iotable_init(at91sam9rl_io_desc, ARRAY_SIZE(at91sam9rl_io_desc)); + + cidr = at91_sys_read(AT91_DBGU_CIDR); + + switch (cidr & AT91_CIDR_SRAMSIZ) { + case AT91_CIDR_SRAMSIZ_32K: + sram_size = 2 * SZ_16K; + break; + case AT91_CIDR_SRAMSIZ_16K: + default: + sram_size = SZ_16K; + } + + at91sam9rl_sram_desc->virtual = AT91_IO_VIRT_BASE - sram_size; + at91sam9rl_sram_desc->length = sram_size; + + /* Map SRAM */ + iotable_init(at91sam9rl_sram_desc, ARRAY_SIZE(at91sam9rl_sram_desc)); + + at91_arch_reset = at91sam9rl_reset; + at91_extern_irq = (1 << AT91SAM9RL_ID_IRQ0); + + /* Init clock subsystem */ + at91_clock_init(main_clock); + + /* Register the processor-specific clocks */ + at91sam9rl_register_clocks(); + + /* Register GPIO subsystem */ + at91_gpio_init(at91sam9rl_gpio, 4); +} + +/* -------------------------------------------------------------------- + * Interrupt initialization + * -------------------------------------------------------------------- */ + +/* + * The default interrupt priority levels (0 = lowest, 7 = highest). + */ +static unsigned int at91sam9rl_default_irq_priority[NR_AIC_IRQS] __initdata = { + 7, /* Advanced Interrupt Controller */ + 7, /* System Peripherals */ + 1, /* Parallel IO Controller A */ + 1, /* Parallel IO Controller B */ + 1, /* Parallel IO Controller C */ + 1, /* Parallel IO Controller D */ + 5, /* USART 0 */ + 5, /* USART 1 */ + 5, /* USART 2 */ + 5, /* USART 3 */ + 0, /* Multimedia Card Interface */ + 6, /* Two-Wire Interface 0 */ + 6, /* Two-Wire Interface 1 */ + 5, /* Serial Peripheral Interface */ + 4, /* Serial Synchronous Controller 0 */ + 4, /* Serial Synchronous Controller 1 */ + 0, /* Timer Counter 0 */ + 0, /* Timer Counter 1 */ + 0, /* Timer Counter 2 */ + 0, + 0, /* Touch Screen Controller */ + 0, /* DMA Controller */ + 2, /* USB Device High speed port */ + 2, /* LCD Controller */ + 6, /* AC97 Controller */ + 0, + 0, + 0, + 0, + 0, + 0, + 0, /* Advanced Interrupt Controller */ +}; + +void __init at91sam9rl_init_interrupts(unsigned int priority[NR_AIC_IRQS]) +{ + if (!priority) + priority = at91sam9rl_default_irq_priority; + + /* Initialize the AIC interrupt controller */ + at91_aic_init(priority); + + /* Enable GPIO interrupts */ + at91_gpio_irq_setup(); +} diff --git a/arch/arm/mach-at91/at91sam9rl_devices.c b/arch/arm/mach-at91/at91sam9rl_devices.c new file mode 100644 index 00000000000..cd7532bcd4e --- /dev/null +++ b/arch/arm/mach-at91/at91sam9rl_devices.c @@ -0,0 +1,630 @@ +/* + * Copyright (C) 2007 Atmel Corporation + * + * This file is subject to the terms and conditions of the GNU General Public + * License. See the file COPYING in the main directory of this archive for + * more details. + */ + +#include <asm/mach/arch.h> +#include <asm/mach/map.h> + +#include <linux/platform_device.h> +#include <linux/fb.h> + +#include <video/atmel_lcdc.h> + +#include <asm/arch/board.h> +#include <asm/arch/gpio.h> +#include <asm/arch/at91sam9rl.h> +#include <asm/arch/at91sam9rl_matrix.h> +#include <asm/arch/at91sam926x_mc.h> + +#include "generic.h" + + +/* -------------------------------------------------------------------- + * MMC / SD + * -------------------------------------------------------------------- */ + +#if defined(CONFIG_MMC_AT91) || defined(CONFIG_MMC_AT91_MODULE) +static u64 mmc_dmamask = 0xffffffffUL; +static struct at91_mmc_data mmc_data; + +static struct resource mmc_resources[] = { + [0] = { + .start = AT91SAM9RL_BASE_MCI, + .end = AT91SAM9RL_BASE_MCI + SZ_16K - 1, + .flags = IORESOURCE_MEM, + }, + [1] = { + .start = AT91SAM9RL_ID_MCI, + .end = AT91SAM9RL_ID_MCI, + .flags = IORESOURCE_IRQ, + }, +}; + +static struct platform_device at91sam9rl_mmc_device = { + .name = "at91_mci", + .id = -1, + .dev = { + .dma_mask = &mmc_dmamask, + .coherent_dma_mask = 0xffffffff, + .platform_data = &mmc_data, + }, + .resource = mmc_resources, + .num_resources = ARRAY_SIZE(mmc_resources), +}; + +void __init at91_add_device_mmc(short mmc_id, struct at91_mmc_data *data) +{ + if (!data) + return; + + /* input/irq */ + if (data->det_pin) { + at91_set_gpio_input(data->det_pin, 1); + at91_set_deglitch(data->det_pin, 1); + } + if (data->wp_pin) + at91_set_gpio_input(data->wp_pin, 1); + if (data->vcc_pin) + at91_set_gpio_output(data->vcc_pin, 0); + + /* CLK */ + at91_set_A_periph(AT91_PIN_PA2, 0); + + /* CMD */ + at91_set_A_periph(AT91_PIN_PA1, 1); + + /* DAT0, maybe DAT1..DAT3 */ + at91_set_A_periph(AT91_PIN_PA0, 1); + if (data->wire4) { + at91_set_A_periph(AT91_PIN_PA3, 1); + at91_set_A_periph(AT91_PIN_PA4, 1); + at91_set_A_periph(AT91_PIN_PA5, 1); + } + + mmc_data = *data; + platform_device_register(&at91sam9rl_mmc_device); +} +#else +void __init at91_add_device_mmc(short mmc_id, struct at91_mmc_data *data) {} +#endif + + +/* -------------------------------------------------------------------- + * NAND / SmartMedia + * -------------------------------------------------------------------- */ + +#if defined(CONFIG_MTD_NAND_AT91) || defined(CONFIG_MTD_NAND_AT91_MODULE) +static struct at91_nand_data nand_data; + +#define NAND_BASE AT91_CHIPSELECT_3 + +static struct resource nand_resources[] = { + { + .start = NAND_BASE, + .end = NAND_BASE + SZ_256M - 1, + .flags = IORESOURCE_MEM, + } +}; + +static struct platform_device at91_nand_device = { + .name = "at91_nand", + .id = -1, + .dev = { + .platform_data = &nand_data, + }, + .resource = nand_resources, + .num_resources = ARRAY_SIZE(nand_resources), +}; + +void __init at91_add_device_nand(struct at91_nand_data *data) +{ + unsigned long csa; + + if (!data) + return; + + csa = at91_sys_read(AT91_MATRIX_EBICSA); + at91_sys_write(AT91_MATRIX_EBICSA, csa | AT91_MATRIX_CS3A_SMC_SMARTMEDIA); + + /* set the bus interface characteristics */ + at91_sys_write(AT91_SMC_SETUP(3), AT91_SMC_NWESETUP_(0) | AT91_SMC_NCS_WRSETUP_(0) + | AT91_SMC_NRDSETUP_(0) | AT91_SMC_NCS_RDSETUP_(0)); + + at91_sys_write(AT91_SMC_PULSE(3), AT91_SMC_NWEPULSE_(2) | AT91_SMC_NCS_WRPULSE_(5) + | AT91_SMC_NRDPULSE_(2) | AT91_SMC_NCS_RDPULSE_(5)); + + at91_sys_write(AT91_SMC_CYCLE(3), AT91_SMC_NWECYCLE_(7) | AT91_SMC_NRDCYCLE_(7)); + + at91_sys_write(AT91_SMC_MODE(3), AT91_SMC_DBW_8 | AT91_SMC_READMODE | AT91_SMC_WRITEMODE | AT91_SMC_EXNWMODE_DISABLE | AT91_SMC_TDF_(1)); + + /* enable pin */ + if (data->enable_pin) + at91_set_gpio_output(data->enable_pin, 1); + + /* ready/busy pin */ + if (data->rdy_pin) + at91_set_gpio_input(data->rdy_pin, 1); + + /* card detect pin */ + if (data->det_pin) + at91_set_gpio_input(data->det_pin, 1); + + at91_set_A_periph(AT91_PIN_PB4, 0); /* NANDOE */ + at91_set_A_periph(AT91_PIN_PB5, 0); /* NANDWE */ + + nand_data = *data; + platform_device_register(&at91_nand_device); +} + +#else +void __init at91_add_device_nand(struct at91_nand_data *data) {} +#endif + + +/* -------------------------------------------------------------------- + * TWI (i2c) + * -------------------------------------------------------------------- */ + +#if defined(CONFIG_I2C_AT91) || defined(CONFIG_I2C_AT91_MODULE) + +static struct resource twi_resources[] = { + [0] = { + .start = AT91SAM9RL_BASE_TWI0, + .end = AT91SAM9RL_BASE_TWI0 + SZ_16K - 1, + .flags = IORESOURCE_MEM, + }, + [1] = { + .start = AT91SAM9RL_ID_TWI0, + .end = AT91SAM9RL_ID_TWI0, + .flags = IORESOURCE_IRQ, + }, +}; + +static struct platform_device at91sam9rl_twi_device = { + .name = "at91_i2c", + .id = -1, + .resource = twi_resources, + .num_resources = ARRAY_SIZE(twi_resources), +}; + +void __init at91_add_device_i2c(void) +{ + /* pins used for TWI interface */ + at91_set_A_periph(AT91_PIN_PA23, 0); /* TWD */ + at91_set_multi_drive(AT91_PIN_PA23, 1); + + at91_set_A_periph(AT91_PIN_PA24, 0); /* TWCK */ + at91_set_multi_drive(AT91_PIN_PA24, 1); + + platform_device_register(&at91sam9rl_twi_device); +} +#else +void __init at91_add_device_i2c(void) {} +#endif + + +/* -------------------------------------------------------------------- + * SPI + * -------------------------------------------------------------------- */ + +#if defined(CONFIG_SPI_ATMEL) || defined(CONFIG_SPI_ATMEL_MODULE) +static u64 spi_dmamask = 0xffffffffUL; + +static struct resource spi_resources[] = { + [0] = { + .start = AT91SAM9RL_BASE_SPI, + .end = AT91SAM9RL_BASE_SPI + SZ_16K - 1, + .flags = IORESOURCE_MEM, + }, + [1] = { + .start = AT91SAM9RL_ID_SPI, + .end = AT91SAM9RL_ID_SPI, + .flags = IORESOURCE_IRQ, + }, +}; + +static struct platform_device at91sam9rl_spi_device = { + .name = "atmel_spi", + .id = 0, + .dev = { + .dma_mask = &spi_dmamask, + .coherent_dma_mask = 0xffffffff, + }, + .resource = spi_resources, + .num_resources = ARRAY_SIZE(spi_resources), +}; + +static const unsigned spi_standard_cs[4] = { AT91_PIN_PA28, AT91_PIN_PB7, AT91_PIN_PD8, AT91_PIN_PD9 }; + + +void __init at91_add_device_spi(struct spi_board_info *devices, int nr_devices) +{ + int i; + unsigned long cs_pin; + + at91_set_A_periph(AT91_PIN_PA25, 0); /* MISO */ + at91_set_A_periph(AT91_PIN_PA26, 0); /* MOSI */ + at91_set_A_periph(AT91_PIN_PA27, 0); /* SPCK */ + + /* Enable SPI chip-selects */ + for (i = 0; i < nr_devices; i++) { + if (devices[i].controller_data) + cs_pin = (unsigned long) devices[i].controller_data; + else + cs_pin = spi_standard_cs[devices[i].chip_select]; + + /* enable chip-select pin */ + at91_set_gpio_output(cs_pin, 1); + + /* pass chip-select pin to driver */ + devices[i].controller_data = (void *) cs_pin; + } + + spi_register_board_info(devices, nr_devices); + platform_device_register(&at91sam9rl_spi_device); +} +#else +void __init at91_add_device_spi(struct spi_board_info *devices, int nr_devices) {} +#endif + + +/* -------------------------------------------------------------------- + * LCD Controller + * -------------------------------------------------------------------- */ + +#if defined(CONFIG_FB_ATMEL) || defined(CONFIG_FB_ATMEL_MODULE) +static u64 lcdc_dmamask = 0xffffffffUL; +static struct atmel_lcdfb_info lcdc_data; + +static struct resource lcdc_resources[] = { + [0] = { + .start = AT91SAM9RL_LCDC_BASE, + .end = AT91SAM9RL_LCDC_BASE + SZ_4K - 1, + .flags = IORESOURCE_MEM, + }, + [1] = { + .start = AT91SAM9RL_ID_LCDC, + .end = AT91SAM9RL_ID_LCDC, + .flags = IORESOURCE_IRQ, + }, +#if defined(CONFIG_FB_INTSRAM) + [2] = { + .start = AT91SAM9RL_SRAM_BASE, + .end = AT91SAM9RL_SRAM_BASE + AT91SAM9RL_SRAM_SIZE - 1, + .flags = IORESOURCE_MEM, + }, +#endif +}; + +static struct platform_device at91_lcdc_device = { + .name = "atmel_lcdfb", + .id = 0, + .dev = { + .dma_mask = &lcdc_dmamask, + .coherent_dma_mask = 0xffffffff, + .platform_data = &lcdc_data, + }, + .resource = lcdc_resources, + .num_resources = ARRAY_SIZE(lcdc_resources), +}; + +void __init at91_add_device_lcdc(struct atmel_lcdfb_info *data) +{ + if (!data) { + return; + } + + at91_set_B_periph(AT91_PIN_PC1, 0); /* LCDPWR */ + at91_set_A_periph(AT91_PIN_PC5, 0); /* LCDHSYNC */ + at91_set_A_periph(AT91_PIN_PC6, 0); /* LCDDOTCK */ + at91_set_A_periph(AT91_PIN_PC7, 0); /* LCDDEN */ + at91_set_A_periph(AT91_PIN_PC3, 0); /* LCDCC */ + at91_set_B_periph(AT91_PIN_PC9, 0); /* LCDD3 */ + at91_set_B_periph(AT91_PIN_PC10, 0); /* LCDD4 */ + at91_set_B_periph(AT91_PIN_PC11, 0); /* LCDD5 */ + at91_set_B_periph(AT91_PIN_PC12, 0); /* LCDD6 */ + at91_set_B_periph(AT91_PIN_PC13, 0); /* LCDD7 */ + at91_set_B_periph(AT91_PIN_PC15, 0); /* LCDD11 */ + at91_set_B_periph(AT91_PIN_PC16, 0); /* LCDD12 */ + at91_set_B_periph(AT91_PIN_PC17, 0); /* LCDD13 */ + at91_set_B_periph(AT91_PIN_PC18, 0); /* LCDD14 */ + at91_set_B_periph(AT91_PIN_PC19, 0); /* LCDD15 */ + at91_set_B_periph(AT91_PIN_PC20, 0); /* LCDD18 */ + at91_set_B_periph(AT91_PIN_PC21, 0); /* LCDD19 */ + at91_set_B_periph(AT91_PIN_PC22, 0); /* LCDD20 */ + at91_set_B_periph(AT91_PIN_PC23, 0); /* LCDD21 */ + at91_set_B_periph(AT91_PIN_PC24, 0); /* LCDD22 */ + at91_set_B_periph(AT91_PIN_PC25, 0); /* LCDD23 */ + + lcdc_data = *data; + platform_device_register(&at91_lcdc_device); +} +#else +void __init at91_add_device_lcdc(struct atmel_lcdfb_info *data) {} +#endif + + +/* -------------------------------------------------------------------- + * LEDs + * -------------------------------------------------------------------- */ + +#if defined(CONFIG_LEDS) +u8 at91_leds_cpu; +u8 at91_leds_timer; + +void __init at91_init_leds(u8 cpu_led, u8 timer_led) +{ + /* Enable GPIO to access the LEDs */ + at91_set_gpio_output(cpu_led, 1); + at91_set_gpio_output(timer_led, 1); + + at91_leds_cpu = cpu_led; + at91_leds_timer = timer_led; +} +#else +void __init at91_init_leds(u8 cpu_led, u8 timer_led) {} +#endif + + +/* -------------------------------------------------------------------- + * UART + * -------------------------------------------------------------------- */ + +#if defined(CONFIG_SERIAL_ATMEL) +static struct resource dbgu_resources[] = { + [0] = { + .start = AT91_VA_BASE_SYS + AT91_DBGU, + .end = AT91_VA_BASE_SYS + AT91_DBGU + SZ_512 - 1, + .flags = IORESOURCE_MEM, + }, + [1] = { + .start = AT91_ID_SYS, + .end = AT91_ID_SYS, + .flags = IORESOURCE_IRQ, + }, +}; + +static struct atmel_uart_data dbgu_data = { + .use_dma_tx = 0, + .use_dma_rx = 0, /* DBGU not capable of receive DMA */ + .regs = (void __iomem *)(AT91_VA_BASE_SYS + AT91_DBGU), +}; + +static struct platform_device at91sam9rl_dbgu_device = { + .name = "atmel_usart", + .id = 0, + .dev = { + .platform_data = &dbgu_data, + .coherent_dma_mask = 0xffffffff, + }, + .resource = dbgu_resources, + .num_resources = ARRAY_SIZE(dbgu_resources), +}; + +static inline void configure_dbgu_pins(void) +{ + at91_set_A_periph(AT91_PIN_PA21, 0); /* DRXD */ + at91_set_A_periph(AT91_PIN_PA22, 1); /* DTXD */ +} + +static struct resource uart0_resources[] = { + [0] = { + .start = AT91SAM9RL_BASE_US0, + .end = AT91SAM9RL_BASE_US0 + SZ_16K - 1, + .flags = IORESOURCE_MEM, + }, + [1] = { + .start = AT91SAM9RL_ID_US0, + .end = AT91SAM9RL_ID_US0, + .flags = IORESOURCE_IRQ, + }, +}; + +static struct atmel_uart_data uart0_data = { + .use_dma_tx = 1, + .use_dma_rx = 1, +}; + +static struct platform_device at91sam9rl_uart0_device = { + .name = "atmel_usart", + .id = 1, + .dev = { + .platform_data = &uart0_data, + .coherent_dma_mask = 0xffffffff, + }, + .resource = uart0_resources, + .num_resources = ARRAY_SIZE(uart0_resources), +}; + +static inline void configure_usart0_pins(void) +{ + at91_set_A_periph(AT91_PIN_PA6, 1); /* TXD0 */ + at91_set_A_periph(AT91_PIN_PA7, 0); /* RXD0 */ + at91_set_A_periph(AT91_PIN_PA9, 0); /* RTS0 */ + at91_set_A_periph(AT91_PIN_PA10, 0); /* CTS0 */ +} + +static struct resource uart1_resources[] = { + [0] = { + .start = AT91SAM9RL_BASE_US1, + .end = AT91SAM9RL_BASE_US1 + SZ_16K - 1, + .flags = IORESOURCE_MEM, + }, + [1] = { + .start = AT91SAM9RL_ID_US1, + .end = AT91SAM9RL_ID_US1, + .flags = IORESOURCE_IRQ, + }, +}; + +static struct atmel_uart_data uart1_data = { + .use_dma_tx = 1, + .use_dma_rx = 1, +}; + +static struct platform_device at91sam9rl_uart1_device = { + .name = "atmel_usart", + .id = 2, + .dev = { + .platform_data = &uart1_data, + .coherent_dma_mask = 0xffffffff, + }, + .resource = uart1_resources, + .num_resources = ARRAY_SIZE(uart1_resources), +}; + +static inline void configure_usart1_pins(void) +{ + at91_set_A_periph(AT91_PIN_PA11, 1); /* TXD1 */ + at91_set_A_periph(AT91_PIN_PA12, 0); /* RXD1 */ +} + +static struct resource uart2_resources[] = { + [0] = { + .start = AT91SAM9RL_BASE_US2, + .end = AT91SAM9RL_BASE_US2 + SZ_16K - 1, + .flags = IORESOURCE_MEM, + }, + [1] = { + .start = AT91SAM9RL_ID_US2, + .end = AT91SAM9RL_ID_US2, + .flags = IORESOURCE_IRQ, + }, +}; + +static struct atmel_uart_data uart2_data = { + .use_dma_tx = 1, + .use_dma_rx = 1, +}; + +static struct platform_device at91sam9rl_uart2_device = { + .name = "atmel_usart", + .id = 3, + .dev = { + .platform_data = &uart2_data, + .coherent_dma_mask = 0xffffffff, + }, + .resource = uart2_resources, + .num_resources = ARRAY_SIZE(uart2_resources), +}; + +static inline void configure_usart2_pins(void) +{ + at91_set_A_periph(AT91_PIN_PA13, 1); /* TXD2 */ + at91_set_A_periph(AT91_PIN_PA14, 0); /* RXD2 */ +} + +static struct resource uart3_resources[] = { + [0] = { + .start = AT91SAM9RL_BASE_US3, + .end = AT91SAM9RL_BASE_US3 + SZ_16K - 1, + .flags = IORESOURCE_MEM, + }, + [1] = { + .start = AT91SAM9RL_ID_US3, + .end = AT91SAM9RL_ID_US3, + .flags = IORESOURCE_IRQ, + }, +}; + +static struct atmel_uart_data uart3_data = { + .use_dma_tx = 1, + .use_dma_rx = 1, +}; + +static struct platform_device at91sam9rl_uart3_device = { + .name = "atmel_usart", + .id = 4, + .dev = { + .platform_data = &uart3_data, + .coherent_dma_mask = 0xffffffff, + }, + .resource = uart3_resources, + .num_resources = ARRAY_SIZE(uart3_resources), +}; + +static inline void configure_usart3_pins(void) +{ + at91_set_A_periph(AT91_PIN_PB0, 1); /* TXD3 */ + at91_set_A_periph(AT91_PIN_PB1, 0); /* RXD3 */ +} + +struct platform_device *at91_uarts[ATMEL_MAX_UART]; /* the UARTs to use */ +struct platform_device *atmel_default_console_device; /* the serial console device */ + +void __init at91_init_serial(struct at91_uart_config *config) +{ + int i; + + /* Fill in list of supported UARTs */ + for (i = 0; i < config->nr_tty; i++) { + switch (config->tty_map[i]) { + case 0: + configure_usart0_pins(); + at91_uarts[i] = &at91sam9rl_uart0_device; + at91_clock_associate("usart0_clk", &at91sam9rl_uart0_device.dev, "usart"); + break; + case 1: + configure_usart1_pins(); + at91_uarts[i] = &at91sam9rl_uart1_device; + at91_clock_associate("usart1_clk", &at91sam9rl_uart1_device.dev, "usart"); + break; + case 2: + configure_usart2_pins(); + at91_uarts[i] = &at91sam9rl_uart2_device; + at91_clock_associate("usart2_clk", &at91sam9rl_uart2_device.dev, "usart"); + break; + case 3: + configure_usart3_pins(); + at91_uarts[i] = &at91sam9rl_uart3_device; + at91_clock_associate("usart3_clk", &at91sam9rl_uart3_device.dev, "usart"); + break; + case 4: + configure_dbgu_pins(); + at91_uarts[i] = &at91sam9rl_dbgu_device; + at91_clock_associate("mck", &at91sam9rl_dbgu_device.dev, "usart"); + break; + default: + continue; + } + at91_uarts[i]->id = i; /* update ID number to mapped ID */ + } + + /* Set serial console device */ + if (config->console_tty < ATMEL_MAX_UART) + atmel_default_console_device = at91_uarts[config->console_tty]; + if (!atmel_default_console_device) + printk(KERN_INFO "AT91: No default serial console defined.\n"); +} + +void __init at91_add_device_serial(void) +{ + int i; + + for (i = 0; i < ATMEL_MAX_UART; i++) { + if (at91_uarts[i]) + platform_device_register(at91_uarts[i]); + } +} +#else +void __init at91_init_serial(struct at91_uart_config *config) {} +void __init at91_add_device_serial(void) {} +#endif + + +/* -------------------------------------------------------------------- */ + +/* + * These devices are always present and don't need any board-specific + * setup. + */ +static int __init at91_add_standard_devices(void) +{ + return 0; +} + +arch_initcall(at91_add_standard_devices); diff --git a/arch/arm/mach-at91/board-sam9rlek.c b/arch/arm/mach-at91/board-sam9rlek.c new file mode 100644 index 00000000000..30c79aca84d --- /dev/null +++ b/arch/arm/mach-at91/board-sam9rlek.c @@ -0,0 +1,204 @@ +/* + * Copyright (C) 2005 SAN People + * Copyright (C) 2007 Atmel Corporation + * + * This file is subject to the terms and conditions of the GNU General Public + * License. See the file COPYING in the main directory of this archive for + * more details. + */ + +#include <linux/types.h> +#include <linux/init.h> +#include <linux/mm.h> +#include <linux/module.h> +#include <linux/platform_device.h> +#include <linux/spi/spi.h> +#include <linux/fb.h> +#include <linux/clk.h> + +#include <video/atmel_lcdc.h> + +#include <asm/hardware.h> +#include <asm/setup.h> +#include <asm/mach-types.h> +#include <asm/irq.h> + +#include <asm/mach/arch.h> +#include <asm/mach/map.h> +#include <asm/mach/irq.h> + +#include <asm/arch/board.h> +#include <asm/arch/gpio.h> +#include <asm/arch/at91sam926x_mc.h> + +#include "generic.h" + + +/* + * Serial port configuration. + * 0 .. 3 = USART0 .. USART3 + * 4 = DBGU + */ +static struct at91_uart_config __initdata ek_uart_config = { + .console_tty = 0, /* ttyS0 */ + .nr_tty = 2, + .tty_map = { 4, 0, -1, -1, -1 } /* ttyS0, ..., ttyS4 */ +}; + +static void __init ek_map_io(void) +{ + /* Initialize processor: 12.000 MHz crystal */ + at91sam9rl_initialize(12000000); + + /* Setup the serial ports and console */ + at91_init_serial(&ek_uart_config); +} + +static void __init ek_init_irq(void) +{ + at91sam9rl_init_interrupts(NULL); +} + + +/* + * MCI (SD/MMC) + */ +static struct at91_mmc_data __initdata ek_mmc_data = { + .wire4 = 1, + .det_pin = AT91_PIN_PA15, +// .wp_pin = ... not connected +// .vcc_pin = ... not connected +}; + + +/* + * NAND flash + */ +static struct mtd_partition __initdata ek_nand_partition[] = { + { + .name = "Partition 1", + .offset = 0, + .size = 256 * 1024, + }, + { + .name = "Partition 2", + .offset = 256 * 1024 , + .size = MTDPART_SIZ_FULL, + }, +}; + +static struct mtd_partition *nand_partitions(int size, int *num_partitions) +{ + *num_partitions = ARRAY_SIZE(ek_nand_partition); + return ek_nand_partition; +} + +static struct at91_nand_data __initdata ek_nand_data = { + .ale = 21, + .cle = 22, +// .det_pin = ... not connected + .rdy_pin = AT91_PIN_PD17, + .enable_pin = AT91_PIN_PB6, + .partition_info = nand_partitions, + .bus_width_16 = 0, +}; + + +/* + * SPI devices + */ +static struct spi_board_info ek_spi_devices[] = { + { /* DataFlash chip */ + .modalias = "mtd_dataflash", + .chip_select = 0, + .max_speed_hz = 15 * 1000 * 1000, + .bus_num = 0, + }, +}; + + +/* + * LCD Controller + */ +#if defined(CONFIG_FB_ATMEL) || defined(CONFIG_FB_ATMEL_MODULE) +static struct fb_videomode at91_tft_vga_modes[] = { + { + .name = "TX09D50VM1CCA @ 60", + .refresh = 60, + .xres = 240, .yres = 320, + .pixclock = KHZ2PICOS(4965), + + .left_margin = 1, .right_margin = 33, + .upper_margin = 1, .lower_margin = 0, + .hsync_len = 5, .vsync_len = 1, + + .sync = FB_SYNC_HOR_HIGH_ACT | FB_SYNC_VERT_HIGH_ACT, + .vmode = FB_VMODE_NONINTERLACED, + }, +}; + +static struct fb_monspecs at91fb_default_monspecs = { + .manufacturer = "HIT", + .monitor = "TX09D50VM1CCA", + + .modedb = at91_tft_vga_modes, + .modedb_len = ARRAY_SIZE(at91_tft_vga_modes), + .hfmin = 15000, + .hfmax = 64000, + .vfmin = 50, + .vfmax = 150, +}; + +#define AT91SAM9RL_DEFAULT_LCDCON2 (ATMEL_LCDC_MEMOR_LITTLE \ + | ATMEL_LCDC_DISTYPE_TFT \ + | ATMEL_LCDC_CLKMOD_ALWAYSACTIVE) + +static void at91_lcdc_power_control(int on) +{ + if (on) + at91_set_gpio_value(AT91_PIN_PA30, 0); /* power up */ + else + at91_set_gpio_value(AT91_PIN_PA30, 1); /* power down */ +} + +/* Driver datas */ +static struct atmel_lcdfb_info __initdata ek_lcdc_data = { + .default_bpp = 16, + .default_dmacon = ATMEL_LCDC_DMAEN, + .default_lcdcon2 = AT91SAM9RL_DEFAULT_LCDCON2, + .default_monspecs = &at91fb_default_monspecs, + .atmel_lcdfb_power_control = at91_lcdc_power_control, + .guard_time = 1, +}; + +#else +static struct atmel_lcdfb_info __initdata ek_lcdc_data; +#endif + + +static void __init ek_board_init(void) +{ + /* Serial */ + at91_add_device_serial(); + /* I2C */ + at91_add_device_i2c(); + /* NAND */ + at91_add_device_nand(&ek_nand_data); + /* SPI */ + at91_add_device_spi(ek_spi_devices, ARRAY_SIZE(ek_spi_devices)); + /* MMC */ + at91_add_device_mmc(0, &ek_mmc_data); + /* LCD Controller */ + at91_add_device_lcdc(&ek_lcdc_data); +} + +MACHINE_START(AT91SAM9RLEK, "Atmel AT91SAM9RL-EK") + /* Maintainer: Atmel */ + .phys_io = AT91_BASE_SYS, + .io_pg_offst = (AT91_VA_BASE_SYS >> 18) & 0xfffc, + .boot_params = AT91_SDRAM_BASE + 0x100, + .timer = &at91sam926x_timer, + .map_io = ek_map_io, + .init_irq = ek_init_irq, + .init_machine = ek_board_init, +MACHINE_END diff --git a/arch/arm/mach-at91/generic.h b/arch/arm/mach-at91/generic.h index bda26221c52..68ed71a3e6c 100644 --- a/arch/arm/mach-at91/generic.h +++ b/arch/arm/mach-at91/generic.h @@ -13,12 +13,14 @@ extern void __init at91rm9200_initialize(unsigned long main_clock, unsigned shor extern void __init at91sam9260_initialize(unsigned long main_clock); extern void __init at91sam9261_initialize(unsigned long main_clock); extern void __init at91sam9263_initialize(unsigned long main_clock); +extern void __init at91sam9rl_initialize(unsigned long main_clock); /* Interrupts */ extern void __init at91rm9200_init_interrupts(unsigned int priority[]); extern void __init at91sam9260_init_interrupts(unsigned int priority[]); extern void __init at91sam9261_init_interrupts(unsigned int priority[]); extern void __init at91sam9263_init_interrupts(unsigned int priority[]); +extern void __init at91sam9rl_init_interrupts(unsigned int priority[]); extern void __init at91_aic_init(unsigned int priority[]); /* Timer */ diff --git a/arch/arm/mach-davinci/Kconfig b/arch/arm/mach-davinci/Kconfig new file mode 100644 index 00000000000..bac988e7a4c --- /dev/null +++ b/arch/arm/mach-davinci/Kconfig @@ -0,0 +1,23 @@ +if ARCH_DAVINCI + +menu "TI DaVinci Implementations" + +comment "DaVinci Core Type" + +config ARCH_DAVINCI644x + default y + bool "DaVinci 644x based system" + +comment "DaVinci Board Type" + +config MACH_DAVINCI_EVM + bool "TI DaVinci EVM" + default y + depends on ARCH_DAVINCI644x + help + Configure this option to specify the whether the board used + for development is a DaVinci EVM + +endmenu + +endif diff --git a/arch/arm/mach-davinci/Makefile b/arch/arm/mach-davinci/Makefile new file mode 100644 index 00000000000..a8f88cd2990 --- /dev/null +++ b/arch/arm/mach-davinci/Makefile @@ -0,0 +1,10 @@ +# +# Makefile for the linux kernel. +# +# + +# Common objects +obj-y := time.o irq.o serial.o io.o id.o psc.o + +# Board specific +obj-$(CONFIG_MACH_DAVINCI_EVM) += board-evm.o diff --git a/arch/arm/mach-davinci/Makefile.boot b/arch/arm/mach-davinci/Makefile.boot new file mode 100644 index 00000000000..e1dd366f836 --- /dev/null +++ b/arch/arm/mach-davinci/Makefile.boot @@ -0,0 +1,3 @@ + zreladdr-y := 0x80008000 +params_phys-y := 0x80000100 +initrd_phys-y := 0x80800000 diff --git a/arch/arm/mach-davinci/board-evm.c b/arch/arm/mach-davinci/board-evm.c new file mode 100644 index 00000000000..633c12e4304 --- /dev/null +++ b/arch/arm/mach-davinci/board-evm.c @@ -0,0 +1,131 @@ +/* + * TI DaVinci EVM board support + * + * Author: Kevin Hilman, MontaVista Software, Inc. <source@mvista.com> + * + * 2007 (c) MontaVista Software, Inc. This file is licensed under + * the terms of the GNU General Public License version 2. This program + * is licensed "as is" without any warranty of any kind, whether express + * or implied. + */ +#include <linux/kernel.h> +#include <linux/module.h> +#include <linux/init.h> +#include <linux/dma-mapping.h> +#include <linux/platform_device.h> +#include <linux/mtd/mtd.h> +#include <linux/mtd/partitions.h> +#include <linux/mtd/physmap.h> + +#include <asm/setup.h> +#include <asm/io.h> +#include <asm/mach-types.h> +#include <asm/hardware.h> + +#include <asm/mach/arch.h> +#include <asm/mach/map.h> +#include <asm/mach/flash.h> + +#include <asm/arch/common.h> + +/* other misc. init functions */ +void __init davinci_psc_init(void); +void __init davinci_irq_init(void); +void __init davinci_map_common_io(void); + +/* NOR Flash base address set to CS0 by default */ +#define NOR_FLASH_PHYS 0x02000000 + +static struct mtd_partition davinci_evm_partitions[] = { + /* bootloader (U-Boot, etc) in first 4 sectors */ + { + .name = "bootloader", + .offset = 0, + .size = 4 * SZ_64K, + .mask_flags = MTD_WRITEABLE, /* force read-only */ + }, + /* bootloader params in the next 1 sectors */ + { + .name = "params", + .offset = MTDPART_OFS_APPEND, + .size = SZ_64K, + .mask_flags = 0, + }, + /* kernel */ + { + .name = "kernel", + .offset = MTDPART_OFS_APPEND, + .size = SZ_2M, + .mask_flags = 0 + }, + /* file system */ + { + .name = "filesystem", + .offset = MTDPART_OFS_APPEND, + .size = MTDPART_SIZ_FULL, + .mask_flags = 0 + } +}; + +static struct physmap_flash_data davinci_evm_flash_data = { + .width = 2, + .parts = davinci_evm_partitions, + .nr_parts = ARRAY_SIZE(davinci_evm_partitions), +}; + +/* NOTE: CFI probe will correctly detect flash part as 32M, but EMIF + * limits addresses to 16M, so using addresses past 16M will wrap */ +static struct resource davinci_evm_flash_resource = { + .start = NOR_FLASH_PHYS, + .end = NOR_FLASH_PHYS + SZ_16M - 1, + .flags = IORESOURCE_MEM, +}; + +static struct platform_device davinci_evm_flash_device = { + .name = "physmap-flash", + .id = 0, + .dev = { + .platform_data = &davinci_evm_flash_data, + }, + .num_resources = 1, + .resource = &davinci_evm_flash_resource, +}; + +static struct platform_device *davinci_evm_devices[] __initdata = { + &davinci_evm_flash_device, +}; + +static void __init +davinci_evm_map_io(void) +{ + davinci_map_common_io(); +} + +static __init void davinci_evm_init(void) +{ + davinci_psc_init(); + +#if defined(CONFIG_BLK_DEV_DAVINCI) || defined(CONFIG_BLK_DEV_DAVINCI_MODULE) + printk(KERN_WARNING "WARNING: both IDE and NOR flash are enabled, " + "but share pins.\n\t Disable IDE for NOR support.\n"); +#endif + + platform_add_devices(davinci_evm_devices, + ARRAY_SIZE(davinci_evm_devices)); +} + +static __init void davinci_evm_irq_init(void) +{ + davinci_irq_init(); +} + +MACHINE_START(DAVINCI_EVM, "DaVinci EVM") + /* Maintainer: MontaVista Software <source@mvista.com> */ + .phys_io = IO_PHYS, + .io_pg_offst = (io_p2v(IO_PHYS) >> 18) & 0xfffc, + .boot_params = (DAVINCI_DDR_BASE + 0x100), + .map_io = davinci_evm_map_io, + .init_irq = davinci_evm_irq_init, + .timer = &davinci_timer, + .init_machine = davinci_evm_init, +MACHINE_END diff --git a/arch/arm/mach-davinci/id.c b/arch/arm/mach-davinci/id.c new file mode 100644 index 00000000000..70608f76aed --- /dev/null +++ b/arch/arm/mach-davinci/id.c @@ -0,0 +1,94 @@ +/* + * Davinci CPU identification code + * + * Copyright (C) 2006 Komal Shah <komal_shah802003@yahoo.com> + * + * Derived from OMAP1 CPU identification code. + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ + +#include <linux/module.h> +#include <linux/kernel.h> +#include <linux/init.h> + +#include <asm/io.h> + +#define JTAG_ID_BASE 0x01c40028 + +struct davinci_id { + u8 variant; /* JTAG ID bits 31:28 */ + u16 part_no; /* JTAG ID bits 27:12 */ + u32 manufacturer; /* JTAG ID bits 11:1 */ + u32 type; /* Cpu id bits [31:8], cpu class bits [7:0] */ +}; + +/* Register values to detect the DaVinci version */ +static struct davinci_id davinci_ids[] __initdata = { + { + /* DM6446 */ + .part_no = 0xb700, + .variant = 0x0, + .manufacturer = 0x017, + .type = 0x64460000, + }, +}; + +/* + * Get Device Part No. from JTAG ID register + */ +static u16 __init davinci_get_part_no(void) +{ + u32 dev_id, part_no; + + dev_id = davinci_readl(JTAG_ID_BASE); + + part_no = ((dev_id >> 12) & 0xffff); + + return part_no; +} + +/* + * Get Device Revision from JTAG ID register + */ +static u8 __init davinci_get_variant(void) +{ + u32 variant; + + variant = davinci_readl(JTAG_ID_BASE); + + variant = (variant >> 28) & 0xf; + + return variant; +} + +void __init davinci_check_revision(void) +{ + int i; + u16 part_no; + u8 variant; + + part_no = davinci_get_part_no(); + variant = davinci_get_variant(); + + /* First check only the major version in a safe way */ + for (i = 0; i < ARRAY_SIZE(davinci_ids); i++) { + if (part_no == (davinci_ids[i].part_no)) { + system_rev = davinci_ids[i].type; + break; + } + } + + /* Check if we can find the dev revision */ + for (i = 0; i < ARRAY_SIZE(davinci_ids); i++) { + if (part_no == davinci_ids[i].part_no && + variant == davinci_ids[i].variant) { + system_rev = davinci_ids[i].type; + break; + } + } + + printk("DaVinci DM%04x variant 0x%x\n", system_rev >> 16, variant); +} diff --git a/arch/arm/mach-davinci/io.c b/arch/arm/mach-davinci/io.c new file mode 100644 index 00000000000..87fae6fb6ec --- /dev/null +++ b/arch/arm/mach-davinci/io.c @@ -0,0 +1,51 @@ +/* + * DaVinci I/O mapping code + * + * Copyright (C) 2005-2006 Texas Instruments + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ + +#include <linux/module.h> +#include <linux/kernel.h> +#include <linux/init.h> + +#include <asm/tlb.h> +#include <asm/io.h> +#include <asm/memory.h> + +#include <asm/mach/map.h> + +extern void davinci_check_revision(void); + +/* + * The machine specific code may provide the extra mapping besides the + * default mapping provided here. + */ +static struct map_desc davinci_io_desc[] __initdata = { + { + .virtual = IO_VIRT, + .pfn = __phys_to_pfn(IO_PHYS), + .length = IO_SIZE, + .type = MT_DEVICE + }, +}; + +void __init davinci_map_common_io(void) +{ + iotable_init(davinci_io_desc, ARRAY_SIZE(davinci_io_desc)); + + /* Normally devicemaps_init() would flush caches and tlb after + * mdesc->map_io(), but we must also do it here because of the CPU + * revision check below. + */ + local_flush_tlb_all(); + flush_cache_all(); + + /* We want to check CPU revision early for cpu_is_xxxx() macros. + * IO space mapping must be initialized before we can do that. + */ + davinci_check_revision(); +} diff --git a/arch/arm/mach-davinci/irq.c b/arch/arm/mach-davinci/irq.c new file mode 100644 index 00000000000..1333d84d2e4 --- /dev/null +++ b/arch/arm/mach-davinci/irq.c @@ -0,0 +1,226 @@ +/* + * Interrupt handler for DaVinci boards. + * + * Copyright (C) 2006 Texas Instruments. + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA. + * + */ +#include <linux/kernel.h> +#include <linux/init.h> +#include <linux/interrupt.h> +#include <linux/irq.h> + +#include <asm/hardware.h> +#include <asm/io.h> +#include <asm/mach/irq.h> + +#define IRQ_BIT(irq) ((irq) & 0x1f) + +#define FIQ_REG0_OFFSET 0x0000 +#define FIQ_REG1_OFFSET 0x0004 +#define IRQ_REG0_OFFSET 0x0008 +#define IRQ_REG1_OFFSET 0x000C +#define IRQ_ENT_REG0_OFFSET 0x0018 +#define IRQ_ENT_REG1_OFFSET 0x001C +#define IRQ_INCTL_REG_OFFSET 0x0020 +#define IRQ_EABASE_REG_OFFSET 0x0024 +#define IRQ_INTPRI0_REG_OFFSET 0x0030 +#define IRQ_INTPRI7_REG_OFFSET 0x004C + +static inline unsigned int davinci_irq_readl(int offset) +{ + return davinci_readl(DAVINCI_ARM_INTC_BASE + offset); +} + +static inline void davinci_irq_writel(unsigned long value, int offset) +{ + davinci_writel(value, DAVINCI_ARM_INTC_BASE + offset); +} + +/* Disable interrupt */ +static void davinci_mask_irq(unsigned int irq) +{ + unsigned int mask; + u32 l; + + mask = 1 << IRQ_BIT(irq); + + if (irq > 31) { + l = davinci_irq_readl(IRQ_ENT_REG1_OFFSET); + l &= ~mask; + davinci_irq_writel(l, IRQ_ENT_REG1_OFFSET); + } else { + l = davinci_irq_readl(IRQ_ENT_REG0_OFFSET); + l &= ~mask; + davinci_irq_writel(l, IRQ_ENT_REG0_OFFSET); + } +} + +/* Enable interrupt */ +static void davinci_unmask_irq(unsigned int irq) +{ + unsigned int mask; + u32 l; + + mask = 1 << IRQ_BIT(irq); + + if (irq > 31) { + l = davinci_irq_readl(IRQ_ENT_REG1_OFFSET); + l |= mask; + davinci_irq_writel(l, IRQ_ENT_REG1_OFFSET); + } else { + l = davinci_irq_readl(IRQ_ENT_REG0_OFFSET); + l |= mask; + davinci_irq_writel(l, IRQ_ENT_REG0_OFFSET); + } +} + +/* EOI interrupt */ +static void davinci_ack_irq(unsigned int irq) +{ + unsigned int mask; + + mask = 1 << IRQ_BIT(irq); + + if (irq > 31) + davinci_irq_writel(mask, IRQ_REG1_OFFSET); + else + davinci_irq_writel(mask, IRQ_REG0_OFFSET); +} + +static struct irq_chip davinci_irq_chip_0 = { + .name = "AINTC", + .ack = davinci_ack_irq, + .mask = davinci_mask_irq, + .unmask = davinci_unmask_irq, +}; + + +/* FIQ are pri 0-1; otherwise 2-7, with 7 lowest priority */ +static const u8 default_priorities[DAVINCI_N_AINTC_IRQ] __initdata = { + [IRQ_VDINT0] = 2, + [IRQ_VDINT1] = 6, + [IRQ_VDINT2] = 6, + [IRQ_HISTINT] = 6, + [IRQ_H3AINT] = 6, + [IRQ_PRVUINT] = 6, + [IRQ_RSZINT] = 6, + [7] = 7, + [IRQ_VENCINT] = 6, + [IRQ_ASQINT] = 6, + [IRQ_IMXINT] = 6, + [IRQ_VLCDINT] = 6, + [IRQ_USBINT] = 4, + [IRQ_EMACINT] = 4, + [14] = 7, + [15] = 7, + [IRQ_CCINT0] = 5, /* dma */ + [IRQ_CCERRINT] = 5, /* dma */ + [IRQ_TCERRINT0] = 5, /* dma */ + [IRQ_TCERRINT] = 5, /* dma */ + [IRQ_PSCIN] = 7, + [21] = 7, + [IRQ_IDE] = 4, + [23] = 7, + [IRQ_MBXINT] = 7, + [IRQ_MBRINT] = 7, + [IRQ_MMCINT] = 7, + [IRQ_SDIOINT] = 7, + [28] = 7, + [IRQ_DDRINT] = 7, + [IRQ_AEMIFINT] = 7, + [IRQ_VLQINT] = 4, + [IRQ_TINT0_TINT12] = 2, /* clockevent */ + [IRQ_TINT0_TINT34] = 2, /* clocksource */ + [IRQ_TINT1_TINT12] = 7, /* DSP timer */ + [IRQ_TINT1_TINT34] = 7, /* system tick */ + [IRQ_PWMINT0] = 7, + [IRQ_PWMINT1] = 7, + [IRQ_PWMINT2] = 7, + [IRQ_I2C] = 3, + [IRQ_UARTINT0] = 3, + [IRQ_UARTINT1] = 3, + [IRQ_UARTINT2] = 3, + [IRQ_SPINT0] = 3, + [IRQ_SPINT1] = 3, + [45] = 7, + [IRQ_DSP2ARM0] = 4, + [IRQ_DSP2ARM1] = 4, + [IRQ_GPIO0] = 7, + [IRQ_GPIO1] = 7, + [IRQ_GPIO2] = 7, + [IRQ_GPIO3] = 7, + [IRQ_GPIO4] = 7, + [IRQ_GPIO5] = 7, + [IRQ_GPIO6] = 7, + [IRQ_GPIO7] = 7, + [IRQ_GPIOBNK0] = 7, + [IRQ_GPIOBNK1] = 7, + [IRQ_GPIOBNK2] = 7, + [IRQ_GPIOBNK3] = 7, + [IRQ_GPIOBNK4] = 7, + [IRQ_COMMTX] = 7, + [IRQ_COMMRX] = 7, + [IRQ_EMUINT] = 7, +}; + +/* ARM Interrupt Controller Initialization */ +void __init davinci_irq_init(void) +{ + unsigned i; + const u8 *priority = default_priorities; + + /* Clear all interrupt requests */ + davinci_irq_writel(~0x0, FIQ_REG0_OFFSET); + davinci_irq_writel(~0x0, FIQ_REG1_OFFSET); + davinci_irq_writel(~0x0, IRQ_REG0_OFFSET); + davinci_irq_writel(~0x0, IRQ_REG1_OFFSET); + + /* Disable all interrupts */ + davinci_irq_writel(0x0, IRQ_ENT_REG0_OFFSET); + davinci_irq_writel(0x0, IRQ_ENT_REG1_OFFSET); + + /* Interrupts disabled immediately, IRQ entry reflects all */ + davinci_irq_writel(0x0, IRQ_INCTL_REG_OFFSET); + + /* we don't use the hardware vector table, just its entry addresses */ + davinci_irq_writel(0, IRQ_EABASE_REG_OFFSET); + + /* Clear all interrupt requests */ + davinci_irq_writel(~0x0, FIQ_REG0_OFFSET); + davinci_irq_writel(~0x0, FIQ_REG1_OFFSET); + davinci_irq_writel(~0x0, IRQ_REG0_OFFSET); + davinci_irq_writel(~0x0, IRQ_REG1_OFFSET); + + for (i = IRQ_INTPRI0_REG_OFFSET; i <= IRQ_INTPRI7_REG_OFFSET; i += 4) { + unsigned j; + u32 pri; + + for (j = 0, pri = 0; j < 32; j += 4, priority++) + pri |= (*priority & 0x07) << j; + davinci_irq_writel(pri, i); + } + + /* set up genirq dispatch for ARM INTC */ + for (i = 0; i < DAVINCI_N_AINTC_IRQ; i++) { + set_irq_chip(i, &davinci_irq_chip_0); + set_irq_flags(i, IRQF_VALID | IRQF_PROBE); + if (i != IRQ_TINT1_TINT34) + set_irq_handler(i, handle_edge_irq); + else + set_irq_handler(i, handle_level_irq); + } +} diff --git a/arch/arm/mach-davinci/psc.c b/arch/arm/mach-davinci/psc.c new file mode 100644 index 00000000000..e1b0050283a --- /dev/null +++ b/arch/arm/mach-davinci/psc.c @@ -0,0 +1,113 @@ +/* + * TI DaVinci Power and Sleep Controller (PSC) + * + * Copyright (C) 2006 Texas Instruments. + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA. + * + */ +#include <linux/kernel.h> +#include <linux/module.h> +#include <linux/init.h> + +#include <asm/io.h> +#include <asm/hardware.h> +#include <asm/arch/psc.h> + +#define PTCMD __REG(0x01C41120) +#define PDSTAT __REG(0x01C41200) +#define PDCTL1 __REG(0x01C41304) +#define EPCPR __REG(0x01C41070) +#define PTSTAT __REG(0x01C41128) + +#define MDSTAT IO_ADDRESS(0x01C41800) +#define MDCTL IO_ADDRESS(0x01C41A00) + +#define PINMUX0 __REG(0x01c40000) +#define PINMUX1 __REG(0x01c40004) +#define VDD3P3V_PWDN __REG(0x01C40048) + +static void davinci_psc_mux(unsigned int id) +{ + switch (id) { + case DAVINCI_LPSC_ATA: + PINMUX0 |= (1 << 17) | (1 << 16); + break; + case DAVINCI_LPSC_MMC_SD: + /* VDD power manupulations are done in U-Boot for CPMAC + * so applies to MMC as well + */ + /*Set up the pull regiter for MMC */ + VDD3P3V_PWDN = 0x0; + PINMUX1 &= (~(1 << 9)); + break; + case DAVINCI_LPSC_I2C: + PINMUX1 |= (1 << 7); + break; + case DAVINCI_LPSC_McBSP: + PINMUX1 |= (1 << 10); + break; + default: + break; + } +} + +/* Enable or disable a PSC domain */ +void davinci_psc_config(unsigned int domain, unsigned int id, char enable) +{ + volatile unsigned int *mdstat = (unsigned int *)((int)MDSTAT + 4 * id); + volatile unsigned int *mdctl = (unsigned int *)((int)MDCTL + 4 * id); + + if (id < 0) + return; + + if (enable) + *mdctl |= 0x00000003; /* Enable Module */ + else + *mdctl &= 0xFFFFFFF2; /* Disable Module */ + + if ((PDSTAT & 0x00000001) == 0) { + PDCTL1 |= 0x1; + PTCMD = (1 << domain); + while ((((EPCPR >> domain) & 1) == 0)); + + PDCTL1 |= 0x100; + while (!(((PTSTAT >> domain) & 1) == 0)); + } else { + PTCMD = (1 << domain); + while (!(((PTSTAT >> domain) & 1) == 0)); + } + + if (enable) + while (!((*mdstat & 0x0000001F) == 0x3)); + else + while (!((*mdstat & 0x0000001F) == 0x2)); + + if (enable) + davinci_psc_mux(id); +} + +void __init davinci_psc_init(void) +{ + davinci_psc_config(DAVINCI_GPSC_ARMDOMAIN, DAVINCI_LPSC_VPSSMSTR, 1); + davinci_psc_config(DAVINCI_GPSC_ARMDOMAIN, DAVINCI_LPSC_VPSSSLV, 1); + davinci_psc_config(DAVINCI_GPSC_ARMDOMAIN, DAVINCI_LPSC_TPCC, 1); + davinci_psc_config(DAVINCI_GPSC_ARMDOMAIN, DAVINCI_LPSC_TPTC0, 1); + davinci_psc_config(DAVINCI_GPSC_ARMDOMAIN, DAVINCI_LPSC_TPTC1, 1); + davinci_psc_config(DAVINCI_GPSC_ARMDOMAIN, DAVINCI_LPSC_GPIO, 1); + + /* Turn on WatchDog timer LPSC. Needed for RESET to work */ + davinci_psc_config(DAVINCI_GPSC_ARMDOMAIN, DAVINCI_LPSC_TIMER2, 1); +} diff --git a/arch/arm/mach-davinci/serial.c b/arch/arm/mach-davinci/serial.c new file mode 100644 index 00000000000..8368c93c788 --- /dev/null +++ b/arch/arm/mach-davinci/serial.c @@ -0,0 +1,96 @@ +/* + * TI DaVinci serial driver + * + * Copyright (C) 2006 Texas Instruments. + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA. + * + */ + +#include <linux/kernel.h> +#include <linux/init.h> +#include <linux/serial_8250.h> +#include <linux/serial_reg.h> +#include <linux/platform_device.h> +#include <linux/delay.h> +#include <linux/clk.h> + +#include <asm/io.h> +#include <asm/irq.h> +#include <asm/hardware.h> +#include <asm/arch/serial.h> +#include <asm/arch/irqs.h> + +#define UART_DAVINCI_PWREMU 0x0c + +static inline unsigned int davinci_serial_in(struct plat_serial8250_port *up, + int offset) +{ + offset <<= up->regshift; + return (unsigned int)__raw_readb(up->membase + offset); +} + +static inline void davinci_serial_outp(struct plat_serial8250_port *p, + int offset, int value) +{ + offset <<= p->regshift; + __raw_writeb(value, p->membase + offset); +} + +static struct plat_serial8250_port serial_platform_data[] = { + { + .membase = (char *)IO_ADDRESS(DAVINCI_UART0_BASE), + .mapbase = (unsigned long)DAVINCI_UART0_BASE, + .irq = IRQ_UARTINT0, + .flags = UPF_BOOT_AUTOCONF | UPF_SKIP_TEST, + .iotype = UPIO_MEM, + .regshift = 2, + .uartclk = 27000000, + }, + { + .flags = 0 + }, +}; + +static struct platform_device serial_device = { + .name = "serial8250", + .id = PLAT8250_DEV_PLATFORM, + .dev = { + .platform_data = serial_platform_data, + }, +}; + +static void __init davinci_serial_reset(struct plat_serial8250_port *p) +{ + /* reset both transmitter and receiver: bits 14,13 = UTRST, URRST */ + unsigned int pwremu = 0; + + davinci_serial_outp(p, UART_IER, 0); /* disable all interrupts */ + + davinci_serial_outp(p, UART_DAVINCI_PWREMU, pwremu); + mdelay(10); + + pwremu |= (0x3 << 13); + pwremu |= 0x1; + davinci_serial_outp(p, UART_DAVINCI_PWREMU, pwremu); +} + +static int __init davinci_init(void) +{ + davinci_serial_reset(&serial_platform_data[0]); + return platform_device_register(&serial_device); +} + +arch_initcall(davinci_init); diff --git a/arch/arm/mach-davinci/time.c b/arch/arm/mach-davinci/time.c new file mode 100644 index 00000000000..4d8425de692 --- /dev/null +++ b/arch/arm/mach-davinci/time.c @@ -0,0 +1,372 @@ +/* + * DaVinci timer subsystem + * + * Author: Kevin Hilman, MontaVista Software, Inc. <source@mvista.com> + * + * 2007 (c) MontaVista Software, Inc. This file is licensed under + * the terms of the GNU General Public License version 2. This program + * is licensed "as is" without any warranty of any kind, whether express + * or implied. + */ +#include <linux/kernel.h> +#include <linux/init.h> +#include <linux/types.h> +#include <linux/interrupt.h> +#include <linux/clocksource.h> +#include <linux/clockchips.h> +#include <linux/spinlock.h> + +#include <asm/io.h> +#include <asm/hardware.h> +#include <asm/system.h> +#include <asm/irq.h> +#include <asm/mach/irq.h> +#include <asm/mach/time.h> +#include <asm/errno.h> +#include <asm/arch/io.h> + +static struct clock_event_device clockevent_davinci; + +#define DAVINCI_TIMER0_BASE (IO_PHYS + 0x21400) +#define DAVINCI_TIMER1_BASE (IO_PHYS + 0x21800) +#define DAVINCI_WDOG_BASE (IO_PHYS + 0x21C00) + +enum { + T0_BOT = 0, T0_TOP, T1_BOT, T1_TOP, NUM_TIMERS, +}; + +#define IS_TIMER1(id) (id & 0x2) +#define IS_TIMER0(id) (!IS_TIMER1(id)) +#define IS_TIMER_TOP(id) ((id & 0x1)) +#define IS_TIMER_BOT(id) (!IS_TIMER_TOP(id)) + +static int timer_irqs[NUM_TIMERS] = { + IRQ_TINT0_TINT12, + IRQ_TINT0_TINT34, + IRQ_TINT1_TINT12, + IRQ_TINT1_TINT34, +}; + +/* + * This driver configures the 2 64-bit count-up timers as 4 independent + * 32-bit count-up timers used as follows: + * + * T0_BOT: Timer 0, bottom: clockevent source for hrtimers + * T0_TOP: Timer 0, top : clocksource for generic timekeeping + * T1_BOT: Timer 1, bottom: (used by DSP in TI DSPLink code) + * T1_TOP: Timer 1, top : <unused> + */ +#define TID_CLOCKEVENT T0_BOT +#define TID_CLOCKSOURCE T0_TOP + +/* Timer register offsets */ +#define PID12 0x0 +#define TIM12 0x10 +#define TIM34 0x14 +#define PRD12 0x18 +#define PRD34 0x1c +#define TCR 0x20 +#define TGCR 0x24 +#define WDTCR 0x28 + +/* Timer register bitfields */ +#define TCR_ENAMODE_DISABLE 0x0 +#define TCR_ENAMODE_ONESHOT 0x1 +#define TCR_ENAMODE_PERIODIC 0x2 +#define TCR_ENAMODE_MASK 0x3 + +#define TGCR_TIMMODE_SHIFT 2 +#define TGCR_TIMMODE_64BIT_GP 0x0 +#define TGCR_TIMMODE_32BIT_UNCHAINED 0x1 +#define TGCR_TIMMODE_64BIT_WDOG 0x2 +#define TGCR_TIMMODE_32BIT_CHAINED 0x3 + +#define TGCR_TIM12RS_SHIFT 0 +#define TGCR_TIM34RS_SHIFT 1 +#define TGCR_RESET 0x0 +#define TGCR_UNRESET 0x1 +#define TGCR_RESET_MASK 0x3 + +#define WDTCR_WDEN_SHIFT 14 +#define WDTCR_WDEN_DISABLE 0x0 +#define WDTCR_WDEN_ENABLE 0x1 +#define WDTCR_WDKEY_SHIFT 16 +#define WDTCR_WDKEY_SEQ0 0xa5c6 +#define WDTCR_WDKEY_SEQ1 0xda7e + +struct timer_s { + char *name; + unsigned int id; + unsigned long period; + unsigned long opts; + unsigned long reg_base; + unsigned long tim_reg; + unsigned long prd_reg; + unsigned long enamode_shift; + struct irqaction irqaction; +}; +static struct timer_s timers[]; + +/* values for 'opts' field of struct timer_s */ +#define TIMER_OPTS_DISABLED 0x00 +#define TIMER_OPTS_ONESHOT 0x01 +#define TIMER_OPTS_PERIODIC 0x02 + +static int timer32_config(struct timer_s *t) +{ + u32 tcr = davinci_readl(t->reg_base + TCR); + + /* disable timer */ + tcr &= ~(TCR_ENAMODE_MASK << t->enamode_shift); + davinci_writel(tcr, t->reg_base + TCR); + + /* reset counter to zero, set new period */ + davinci_writel(0, t->tim_reg); + davinci_writel(t->period, t->prd_reg); + + /* Set enable mode */ + if (t->opts & TIMER_OPTS_ONESHOT) { + tcr |= TCR_ENAMODE_ONESHOT << t->enamode_shift; + } else if (t->opts & TIMER_OPTS_PERIODIC) { + tcr |= TCR_ENAMODE_PERIODIC << t->enamode_shift; + } + + davinci_writel(tcr, t->reg_base + TCR); + return 0; +} + +static inline u32 timer32_read(struct timer_s *t) +{ + return davinci_readl(t->tim_reg); +} + +static irqreturn_t timer_interrupt(int irq, void *dev_id) +{ + struct clock_event_device *evt = &clockevent_davinci; + + evt->event_handler(evt); + return IRQ_HANDLED; +} + +/* called when 32-bit counter wraps */ +static irqreturn_t freerun_interrupt(int irq, void *dev_id) +{ + return IRQ_HANDLED; +} + +static struct timer_s timers[] = { + [TID_CLOCKEVENT] = { + .name = "clockevent", + .opts = TIMER_OPTS_DISABLED, + .irqaction = { + .flags = IRQF_DISABLED | IRQF_TIMER, + .handler = timer_interrupt, + } + }, + [TID_CLOCKSOURCE] = { + .name = "free-run counter", + .period = ~0, + .opts = TIMER_OPTS_PERIODIC, + .irqaction = { + .flags = IRQF_DISABLED | IRQF_TIMER, + .handler = freerun_interrupt, + } + }, +}; + +static void __init timer_init(void) +{ + u32 bases[] = {DAVINCI_TIMER0_BASE, DAVINCI_TIMER1_BASE}; + int i; + + /* Global init of each 64-bit timer as a whole */ + for(i=0; i<2; i++) { + u32 tgcr, base = bases[i]; + + /* Disabled, Internal clock source */ + davinci_writel(0, base + TCR); + + /* reset both timers, no pre-scaler for timer34 */ + tgcr = 0; + davinci_writel(tgcr, base + TGCR); + + /* Set both timers to unchained 32-bit */ + tgcr = TGCR_TIMMODE_32BIT_UNCHAINED << TGCR_TIMMODE_SHIFT; + davinci_writel(tgcr, base + TGCR); + + /* Unreset timers */ + tgcr |= (TGCR_UNRESET << TGCR_TIM12RS_SHIFT) | + (TGCR_UNRESET << TGCR_TIM34RS_SHIFT); + davinci_writel(tgcr, base + TGCR); + + /* Init both counters to zero */ + davinci_writel(0, base + TIM12); + davinci_writel(0, base + TIM34); + } + + /* Init of each timer as a 32-bit timer */ + for (i=0; i< ARRAY_SIZE(timers); i++) { + struct timer_s *t = &timers[i]; + + if (t->name) { + t->id = i; + t->reg_base = (IS_TIMER1(t->id) ? + DAVINCI_TIMER1_BASE : DAVINCI_TIMER0_BASE); + + if (IS_TIMER_BOT(t->id)) { + t->enamode_shift = 6; + t->tim_reg = t->reg_base + TIM12; + t->prd_reg = t->reg_base + PRD12; + } else { + t->enamode_shift = 22; + t->tim_reg = t->reg_base + TIM34; + t->prd_reg = t->reg_base + PRD34; + } + + /* Register interrupt */ + t->irqaction.name = t->name; + t->irqaction.dev_id = (void *)t; + if (t->irqaction.handler != NULL) { + setup_irq(timer_irqs[t->id], &t->irqaction); + } + + timer32_config(&timers[i]); + } + } +} + +/* + * clocksource + */ +static cycle_t read_cycles(void) +{ + struct timer_s *t = &timers[TID_CLOCKSOURCE]; + + return (cycles_t)timer32_read(t); +} + +static struct clocksource clocksource_davinci = { + .name = "timer0_1", + .rating = 300, + .read = read_cycles, + .mask = CLOCKSOURCE_MASK(32), + .shift = 24, + .flags = CLOCK_SOURCE_IS_CONTINUOUS, +}; + +/* + * clockevent + */ +static int davinci_set_next_event(unsigned long cycles, + struct clock_event_device *evt) +{ + struct timer_s *t = &timers[TID_CLOCKEVENT]; + + t->period = cycles; + timer32_config(t); + return 0; +} + +static void davinci_set_mode(enum clock_event_mode mode, + struct clock_event_device *evt) +{ + struct timer_s *t = &timers[TID_CLOCKEVENT]; + + switch (mode) { + case CLOCK_EVT_MODE_PERIODIC: + t->period = CLOCK_TICK_RATE / (HZ); + t->opts = TIMER_OPTS_PERIODIC; + timer32_config(t); + break; + case CLOCK_EVT_MODE_ONESHOT: + t->opts = TIMER_OPTS_ONESHOT; + break; + case CLOCK_EVT_MODE_UNUSED: + case CLOCK_EVT_MODE_SHUTDOWN: + t->opts = TIMER_OPTS_DISABLED; + break; + } +} + +static struct clock_event_device clockevent_davinci = { + .name = "timer0_0", + .features = CLOCK_EVT_FEAT_PERIODIC | CLOCK_EVT_FEAT_ONESHOT, + .shift = 32, + .set_next_event = davinci_set_next_event, + .set_mode = davinci_set_mode, +}; + + +static void __init davinci_timer_init(void) +{ + static char err[] __initdata = KERN_ERR + "%s: can't register clocksource!\n"; + + /* init timer hw */ + timer_init(); + + /* setup clocksource */ + clocksource_davinci.mult = + clocksource_khz2mult(CLOCK_TICK_RATE/1000, + clocksource_davinci.shift); + if (clocksource_register(&clocksource_davinci)) + printk(err, clocksource_davinci.name); + + /* setup clockevent */ + clockevent_davinci.mult = div_sc(CLOCK_TICK_RATE, NSEC_PER_SEC, + clockevent_davinci.shift); + clockevent_davinci.max_delta_ns = + clockevent_delta2ns(0xfffffffe, &clockevent_davinci); + clockevent_davinci.min_delta_ns = + clockevent_delta2ns(1, &clockevent_davinci); + + clockevent_davinci.cpumask = cpumask_of_cpu(0); + clockevents_register_device(&clockevent_davinci); +} + +struct sys_timer davinci_timer = { + .init = davinci_timer_init, +}; + + +/* reset board using watchdog timer */ +void davinci_watchdog_reset(void) { + u32 tgcr, wdtcr, base = DAVINCI_WDOG_BASE; + + /* disable, internal clock source */ + davinci_writel(0, base + TCR); + + /* reset timer, set mode to 64-bit watchdog, and unreset */ + tgcr = 0; + davinci_writel(tgcr, base + TCR); + tgcr = TGCR_TIMMODE_64BIT_WDOG << TGCR_TIMMODE_SHIFT; + tgcr |= (TGCR_UNRESET << TGCR_TIM12RS_SHIFT) | + (TGCR_UNRESET << TGCR_TIM34RS_SHIFT); + davinci_writel(tgcr, base + TCR); + + /* clear counter and period regs */ + davinci_writel(0, base + TIM12); + davinci_writel(0, base + TIM34); + davinci_writel(0, base + PRD12); + davinci_writel(0, base + PRD34); + + /* enable */ + wdtcr = davinci_readl(base + WDTCR); + wdtcr |= WDTCR_WDEN_ENABLE << WDTCR_WDEN_SHIFT; + davinci_writel(wdtcr, base + WDTCR); + + /* put watchdog in pre-active state */ + wdtcr = (WDTCR_WDKEY_SEQ0 << WDTCR_WDKEY_SHIFT) | + (WDTCR_WDEN_ENABLE << WDTCR_WDEN_SHIFT); + davinci_writel(wdtcr, base + WDTCR); + + /* put watchdog in active state */ + wdtcr = (WDTCR_WDKEY_SEQ1 << WDTCR_WDKEY_SHIFT) | + (WDTCR_WDEN_ENABLE << WDTCR_WDEN_SHIFT); + davinci_writel(wdtcr, base + WDTCR); + + /* write an invalid value to the WDKEY field to trigger + * a watchdog reset */ + wdtcr = 0x00004000; + davinci_writel(wdtcr, base + WDTCR); +} diff --git a/arch/arm/mach-iop13xx/Makefile b/arch/arm/mach-iop13xx/Makefile index da1609dc0de..cad015fee12 100644 --- a/arch/arm/mach-iop13xx/Makefile +++ b/arch/arm/mach-iop13xx/Makefile @@ -10,3 +10,4 @@ obj-$(CONFIG_ARCH_IOP13XX) += io.o obj-$(CONFIG_ARCH_IOP13XX) += tpmi.o obj-$(CONFIG_MACH_IQ81340SC) += iq81340sc.o obj-$(CONFIG_MACH_IQ81340MC) += iq81340mc.o +obj-$(CONFIG_PCI_MSI) += msi.o diff --git a/arch/arm/mach-iop13xx/irq.c b/arch/arm/mach-iop13xx/irq.c index b2eb0b96103..5791addd436 100644 --- a/arch/arm/mach-iop13xx/irq.c +++ b/arch/arm/mach-iop13xx/irq.c @@ -26,6 +26,7 @@ #include <asm/hardware.h> #include <asm/mach-types.h> #include <asm/arch/irqs.h> +#include <asm/arch/msi.h> /* INTCTL0 CP6 R0 Page 4 */ @@ -258,7 +259,7 @@ void __init iop13xx_init_irq(void) write_intbase(INTBASE); write_intsize(INTSIZE_4); - for(i = 0; i < NR_IOP13XX_IRQS; i++) { + for(i = 0; i <= IRQ_IOP13XX_HPI; i++) { if (i < 32) set_irq_chip(i, &iop13xx_irqchip1); else if (i < 64) @@ -271,4 +272,6 @@ void __init iop13xx_init_irq(void) set_irq_handler(i, handle_level_irq); set_irq_flags(i, IRQF_VALID | IRQF_PROBE); } + + iop13xx_msi_init(); } diff --git a/arch/arm/mach-iop13xx/msi.c b/arch/arm/mach-iop13xx/msi.c new file mode 100644 index 00000000000..2d236930222 --- /dev/null +++ b/arch/arm/mach-iop13xx/msi.c @@ -0,0 +1,194 @@ +/* + * arch/arm/mach-iop13xx/msi.c + * + * PCI MSI support for the iop13xx processor + * + * Copyright (c) 2006, Intel Corporation. + * + * This program is free software; you can redistribute it and/or modify it + * under the terms and conditions of the GNU General Public License, + * version 2, as published by the Free Software Foundation. + * + * This program is distributed in the hope it will be useful, but WITHOUT + * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or + * FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for + * more details. + * + * You should have received a copy of the GNU General Public License along with + * this program; if not, write to the Free Software Foundation, Inc., 59 Temple + * Place - Suite 330, Boston, MA 02111-1307 USA. + * + */ +#include <linux/pci.h> +#include <linux/msi.h> +#include <asm/mach/irq.h> +#include <asm/irq.h> + + +#define IOP13XX_NUM_MSI_IRQS 128 +static DECLARE_BITMAP(msi_irq_in_use, IOP13XX_NUM_MSI_IRQS); + +/* IMIPR0 CP6 R8 Page 1 + */ +static inline u32 read_imipr_0(void) +{ + u32 val; + asm volatile("mrc p6, 0, %0, c8, c1, 0":"=r" (val)); + return val; +} +static inline void write_imipr_0(u32 val) +{ + asm volatile("mcr p6, 0, %0, c8, c1, 0"::"r" (val)); +} + +/* IMIPR1 CP6 R9 Page 1 + */ +static inline u32 read_imipr_1(void) +{ + u32 val; + asm volatile("mrc p6, 0, %0, c9, c1, 0":"=r" (val)); + return val; +} +static inline void write_imipr_1(u32 val) +{ + asm volatile("mcr p6, 0, %0, c9, c1, 0"::"r" (val)); +} + +/* IMIPR2 CP6 R10 Page 1 + */ +static inline u32 read_imipr_2(void) +{ + u32 val; + asm volatile("mrc p6, 0, %0, c10, c1, 0":"=r" (val)); + return val; +} +static inline void write_imipr_2(u32 val) +{ + asm volatile("mcr p6, 0, %0, c10, c1, 0"::"r" (val)); +} + +/* IMIPR3 CP6 R11 Page 1 + */ +static inline u32 read_imipr_3(void) +{ + u32 val; + asm volatile("mrc p6, 0, %0, c11, c1, 0":"=r" (val)); + return val; +} +static inline void write_imipr_3(u32 val) +{ + asm volatile("mcr p6, 0, %0, c11, c1, 0"::"r" (val)); +} + +static u32 (*read_imipr[])(void) = { + read_imipr_0, + read_imipr_1, + read_imipr_2, + read_imipr_3, +}; + +static void (*write_imipr[])(u32) = { + write_imipr_0, + write_imipr_1, + write_imipr_2, + write_imipr_3, +}; + +static void iop13xx_msi_handler(unsigned int irq, struct irq_desc *desc) +{ + int i, j; + unsigned long status; + + /* read IMIPR registers and find any active interrupts, + * then call ISR for each active interrupt + */ + for (i = 0; i < ARRAY_SIZE(read_imipr); i++) { + status = (read_imipr[i])(); + if (!status) + continue; + + do { + j = find_first_bit(&status, 32); + (write_imipr[i])(1 << j); /* write back to clear bit */ + desc = irq_desc + IRQ_IOP13XX_MSI_0 + j + (32*i); + desc_handle_irq(IRQ_IOP13XX_MSI_0 + j + (32*i), desc); + status = (read_imipr[i])(); + } while (status); + } +} + +void __init iop13xx_msi_init(void) +{ + set_irq_chained_handler(IRQ_IOP13XX_INBD_MSI, iop13xx_msi_handler); +} + +/* + * Dynamic irq allocate and deallocation + */ +int create_irq(void) +{ + int irq, pos; + +again: + pos = find_first_zero_bit(msi_irq_in_use, IOP13XX_NUM_MSI_IRQS); + irq = IRQ_IOP13XX_MSI_0 + pos; + if (irq > NR_IRQS) + return -ENOSPC; + /* test_and_set_bit operates on 32-bits at a time */ + if (test_and_set_bit(pos, msi_irq_in_use)) + goto again; + + dynamic_irq_init(irq); + + return irq; +} + +void destroy_irq(unsigned int irq) +{ + int pos = irq - IRQ_IOP13XX_MSI_0; + + dynamic_irq_cleanup(irq); + + clear_bit(pos, msi_irq_in_use); +} + +void arch_teardown_msi_irq(unsigned int irq) +{ + destroy_irq(irq); +} + +static void iop13xx_msi_nop(unsigned int irq) +{ + return; +} + +static struct irq_chip iop13xx_msi_chip = { + .name = "PCI-MSI", + .ack = iop13xx_msi_nop, + .enable = unmask_msi_irq, + .disable = mask_msi_irq, + .mask = mask_msi_irq, + .unmask = unmask_msi_irq, +}; + +int arch_setup_msi_irq(struct pci_dev *pdev, struct msi_desc *desc) +{ + int id, irq = create_irq(); + struct msi_msg msg; + + if (irq < 0) + return irq; + + set_irq_msi(irq, desc); + + msg.address_hi = 0x0; + msg.address_lo = IOP13XX_MU_MIMR_PCI; + + id = iop13xx_cpu_id(); + msg.data = (id << IOP13XX_MU_MIMR_CORE_SELECT) | (irq & 0x7f); + + write_msi_msg(irq, &msg); + set_irq_chip_and_handler(irq, &iop13xx_msi_chip, handle_simple_irq); + + return irq; +} diff --git a/arch/arm/mach-iop13xx/pci.c b/arch/arm/mach-iop13xx/pci.c index d1d0d32ca77..1c9e94c38b7 100644 --- a/arch/arm/mach-iop13xx/pci.c +++ b/arch/arm/mach-iop13xx/pci.c @@ -559,6 +559,14 @@ void __init iop13xx_atue_setup(void) int func = iop13xx_atu_function(IOP13XX_INIT_ATU_ATUE); u32 reg_val; +#ifdef CONFIG_PCI_MSI + /* BAR 0 (inbound msi window) */ + __raw_writel(IOP13XX_MU_BASE_PHYS, IOP13XX_MU_MUBAR); + __raw_writel(~(IOP13XX_MU_WINDOW_SIZE - 1), IOP13XX_ATUE_IALR0); + __raw_writel(IOP13XX_MU_BASE_PHYS, IOP13XX_ATUE_IATVR0); + __raw_writel(IOP13XX_MU_BASE_PCI, IOP13XX_ATUE_IABAR0); +#endif + /* BAR 1 (1:1 mapping with Physical RAM) */ /* Set limit and enable */ __raw_writel(~(IOP13XX_MAX_RAM_SIZE - PHYS_OFFSET - 1) & ~0x1, @@ -720,6 +728,14 @@ void __init iop13xx_atux_setup(void) else atux_trhfa_timeout = jiffies; +#ifdef CONFIG_PCI_MSI + /* BAR 0 (inbound msi window) */ + __raw_writel(IOP13XX_MU_BASE_PHYS, IOP13XX_MU_MUBAR); + __raw_writel(~(IOP13XX_MU_WINDOW_SIZE - 1), IOP13XX_ATUX_IALR0); + __raw_writel(IOP13XX_MU_BASE_PHYS, IOP13XX_ATUX_IATVR0); + __raw_writel(IOP13XX_MU_BASE_PCI, IOP13XX_ATUX_IABAR0); +#endif + /* BAR 1 (1:1 mapping with Physical RAM) */ /* Set limit and enable */ __raw_writel(~(IOP13XX_MAX_RAM_SIZE - PHYS_OFFSET - 1) & ~0x1, diff --git a/arch/arm/mach-ks8695/Kconfig b/arch/arm/mach-ks8695/Kconfig new file mode 100644 index 00000000000..ce1cf8de2b4 --- /dev/null +++ b/arch/arm/mach-ks8695/Kconfig @@ -0,0 +1,13 @@ +if ARCH_KS8695 + +menu "Kendin/Micrel KS8695 Implementations" + +config MACH_KS8695 + bool "KS8695 development board" + help + Say 'Y' here if you want your kernel to run on the original + Kendin-Micrel KS8695 development board. + +endmenu + +endif diff --git a/arch/arm/mach-ks8695/Makefile b/arch/arm/mach-ks8695/Makefile new file mode 100644 index 00000000000..56b7d337333 --- /dev/null +++ b/arch/arm/mach-ks8695/Makefile @@ -0,0 +1,15 @@ +# arch/arm/mach-ks8695/Makefile +# +# Makefile for KS8695 architecture support +# + +obj-y := cpu.o irq.o time.o devices.o +obj-m := +obj-n := +obj- := + +# PCI support is optional +#obj-$(CONFIG_PCI) += pci.o + +# Board-specific support +obj-$(CONFIG_MACH_KS8695) += board-micrel.o diff --git a/arch/arm/mach-ks8695/Makefile.boot b/arch/arm/mach-ks8695/Makefile.boot new file mode 100644 index 00000000000..48eb2cb3ac7 --- /dev/null +++ b/arch/arm/mach-ks8695/Makefile.boot @@ -0,0 +1,8 @@ +# Note: the following conditions must always be true: +# ZRELADDR == virt_to_phys(TEXTADDR) +# PARAMS_PHYS must be within 4MB of ZRELADDR +# INITRD_PHYS must be in RAM + + zreladdr-y := 0x00008000 +params_phys-y := 0x00000100 +initrd_phys-y := 0x00800000 diff --git a/arch/arm/mach-ks8695/board-micrel.c b/arch/arm/mach-ks8695/board-micrel.c new file mode 100644 index 00000000000..8fc0edb5211 --- /dev/null +++ b/arch/arm/mach-ks8695/board-micrel.c @@ -0,0 +1,60 @@ +/* + * arch/arm/mach-ks8695/board-micrel.c + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ + +#include <linux/kernel.h> +#include <linux/types.h> +#include <linux/interrupt.h> +#include <linux/init.h> +#include <linux/platform_device.h> + +#include <asm/mach-types.h> + +#include <asm/mach/arch.h> +#include <asm/mach/map.h> +#include <asm/mach/irq.h> + +#include <asm/arch/devices.h> + +#include "generic.h" + +#ifdef CONFIG_PCI +static int __init micrel_pci_map_irq(struct pci_dev *dev, u8 slot, u8 pin) +{ + return KS8695_IRQ_EXTERN0; +} + +static struct ks8695_pci_cfg micrel_pci = { + .mode = KS8695_MODE_MINIPCI, + .map_irq = micrel_pci_map_irq, +}; +#endif + + +static void micrel_init(void) +{ + printk(KERN_INFO "Micrel KS8695 Development Board initializing\n"); + +#ifdef CONFIG_PCI + ks8695_init_pci(&micrel_pci); +#endif + + /* Add devices */ + ks8695_add_device_wan(); /* eth0 = WAN */ + ks8695_add_device_lan(); /* eth1 = LAN */ +} + +MACHINE_START(KS8695, "KS8695 Centaur Development Board") + /* Maintainer: Micrel Semiconductor Inc. */ + .phys_io = KS8695_IO_PA, + .io_pg_offst = (KS8695_IO_VA >> 18) & 0xfffc, + .boot_params = KS8695_SDRAM_PA + 0x100, + .map_io = ks8695_map_io, + .init_irq = ks8695_init_irq, + .init_machine = micrel_init, + .timer = &ks8695_timer, +MACHINE_END diff --git a/arch/arm/mach-ks8695/cpu.c b/arch/arm/mach-ks8695/cpu.c new file mode 100644 index 00000000000..407d255e42b --- /dev/null +++ b/arch/arm/mach-ks8695/cpu.c @@ -0,0 +1,73 @@ +/* + * arch/arm/mach-ks8695/cpu.c + * + * Copyright (C) 2006 Ben Dooks <ben@simtec.co.uk> + * Copyright (C) 2006 Simtec Electronics + * + * KS8695 CPU support + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA + */ + +#include <linux/kernel.h> +#include <linux/module.h> +#include <linux/init.h> + +#include <asm/hardware.h> +#include <asm/io.h> +#include <asm/mach/arch.h> +#include <asm/mach/map.h> + +#include <asm/arch/regs-sys.h> +#include <asm/arch/regs-misc.h> + + +static struct __initdata map_desc ks8695_io_desc[] = { + { + .virtual = KS8695_IO_VA, + .pfn = __phys_to_pfn(KS8695_IO_PA), + .length = KS8695_IO_SIZE, + .type = MT_DEVICE, + } +}; + +static void __init ks8695_processor_info(void) +{ + unsigned long id, rev; + + id = __raw_readl(KS8695_MISC_VA + KS8695_DID); + rev = __raw_readl(KS8695_MISC_VA + KS8695_RID); + + printk("KS8695 ID=%04lx SubID=%02lx Revision=%02lx\n", (id & DID_ID), (rev & RID_SUBID), (rev & RID_REVISION)); +} + +static unsigned int sysclk[8] = { 125000000, 100000000, 62500000, 50000000, 41700000, 33300000, 31300000, 25000000 }; +static unsigned int cpuclk[8] = { 166000000, 166000000, 83000000, 83000000, 55300000, 55300000, 41500000, 41500000 }; + +static void __init ks8695_clock_info(void) +{ + unsigned int scdc = __raw_readl(KS8695_SYS_VA + KS8695_CLKCON) & CLKCON_SCDC; + + printk("Clocks: System %u MHz, CPU %u MHz\n", + sysclk[scdc] / 1000000, cpuclk[scdc] / 1000000); +} + +void __init ks8695_map_io(void) +{ + iotable_init(ks8695_io_desc, ARRAY_SIZE(ks8695_io_desc)); + + ks8695_processor_info(); + ks8695_clock_info(); +} diff --git a/arch/arm/mach-ks8695/devices.c b/arch/arm/mach-ks8695/devices.c new file mode 100644 index 00000000000..386593f8ac6 --- /dev/null +++ b/arch/arm/mach-ks8695/devices.c @@ -0,0 +1,191 @@ +/* + * arch/arm/mach-ks8695/devices.c + * + * Copyright (C) 2006 Andrew Victor + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA + */ + +#include <asm/mach/arch.h> +#include <asm/mach/map.h> + +#include <linux/platform_device.h> + +#include <asm/arch/regs-wan.h> +#include <asm/arch/regs-lan.h> +#include <asm/arch/regs-hpna.h> + + +/* -------------------------------------------------------------------- + * Ethernet + * -------------------------------------------------------------------- */ + +#if defined(CONFIG_ARM_KS8695_ETHER) || defined(CONFIG_ARM_KS8695_ETHER_MODULE) +static u64 eth_dmamask = 0xffffffffUL; + +static struct resource ks8695_wan_resources[] = { + [0] = { + .start = KS8695_WAN_VA, + .end = KS8695_WAN_VA + 0x00ff, + .flags = IORESOURCE_MEM, + }, + [1] = { + .name = "WAN RX", + .start = KS8695_IRQ_WAN_RX_STATUS, + .end = KS8695_IRQ_WAN_RX_STATUS, + .flags = IORESOURCE_IRQ, + }, + [2] = { + .name = "WAN TX", + .start = KS8695_IRQ_WAN_TX_STATUS, + .end = KS8695_IRQ_WAN_TX_STATUS, + .flags = IORESOURCE_IRQ, + }, + [3] = { + .name = "WAN Link", + .start = KS8695_IRQ_WAN_LINK, + .end = KS8695_IRQ_WAN_LINK, + .flags = IORESOURCE_IRQ, + }, +}; + +static struct platform_device ks8695_wan_device = { + .name = "ks8695_ether", + .id = 0, + .dev = { + .dma_mask = ð_dmamask, + .coherent_dma_mask = 0xffffffff, + }, + .resource = ks8695_wan_resources, + .num_resources = ARRAY_SIZE(ks8695_wan_resources), +}; + + +static struct resource ks8695_lan_resources[] = { + [0] = { + .start = KS8695_LAN_VA, + .end = KS8695_LAN_VA + 0x00ff, + .flags = IORESOURCE_MEM, + }, + [1] = { + .name = "LAN RX", + .start = KS8695_IRQ_LAN_RX_STATUS, + .end = KS8695_IRQ_LAN_RX_STATUS, + .flags = IORESOURCE_IRQ, + }, + [2] = { + .name = "LAN TX", + .start = KS8695_IRQ_LAN_TX_STATUS, + .end = KS8695_IRQ_LAN_TX_STATUS, + .flags = IORESOURCE_IRQ, + }, +}; + +static struct platform_device ks8695_lan_device = { + .name = "ks8695_ether", + .id = 1, + .dev = { + .dma_mask = ð_dmamask, + .coherent_dma_mask = 0xffffffff, + }, + .resource = ks8695_lan_resources, + .num_resources = ARRAY_SIZE(ks8695_lan_resources), +}; + + +static struct resource ks8695_hpna_resources[] = { + [0] = { + .start = KS8695_HPNA_VA, + .end = KS8695_HPNA_VA + 0x00ff, + .flags = IORESOURCE_MEM, + }, + [1] = { + .name = "HPNA RX", + .start = KS8695_IRQ_HPNA_RX_STATUS, + .end = KS8695_IRQ_HPNA_RX_STATUS, + .flags = IORESOURCE_IRQ, + }, + [2] = { + .name = "HPNA TX", + .start = KS8695_IRQ_HPNA_TX_STATUS, + .end = KS8695_IRQ_HPNA_TX_STATUS, + .flags = IORESOURCE_IRQ, + }, +}; + +static struct platform_device ks8695_hpna_device = { + .name = "ks8695_ether", + .id = 2, + .dev = { + .dma_mask = ð_dmamask, + .coherent_dma_mask = 0xffffffff, + }, + .resource = ks8695_hpna_resources, + .num_resources = ARRAY_SIZE(ks8695_hpna_resources), +}; + +void __init ks8695_add_device_wan(void) +{ + platform_device_register(&ks8695_wan_device); +} + +void __init ks8695_add_device_lan(void) +{ + platform_device_register(&ks8695_lan_device); +} + +void __init ks8696_add_device_hpna(void) +{ + platform_device_register(&ks8695_hpna_device); +} +#else +void __init ks8695_add_device_wan(void) {} +void __init ks8695_add_device_lan(void) {} +void __init ks8696_add_device_hpna(void) {} +#endif + + +/* -------------------------------------------------------------------- + * Watchdog + * -------------------------------------------------------------------- */ + +#if defined(CONFIG_KS8695_WATCHDOG) || defined(CONFIG_KS8695_WATCHDOG_MODULE) +static struct platform_device ks8695_wdt_device = { + .name = "ks8695_wdt", + .id = -1, + .num_resources = 0, +}; + +static void __init ks8695_add_device_watchdog(void) +{ + platform_device_register(&ks8695_wdt_device); +} +#else +static void __init ks8695_add_device_watchdog(void) {} +#endif + + +/* -------------------------------------------------------------------- */ + +/* + * These devices are always present and don't need any board-specific + * setup. + */ +static int __init ks8695_add_standard_devices(void) +{ + ks8695_add_device_watchdog(); + return 0; +} + +arch_initcall(ks8695_add_standard_devices); diff --git a/arch/arm/mach-ks8695/generic.h b/arch/arm/mach-ks8695/generic.h new file mode 100644 index 00000000000..2fbfab8d5fa --- /dev/null +++ b/arch/arm/mach-ks8695/generic.h @@ -0,0 +1,15 @@ +/* + * arch/arm/mach-ks8695/generic.h + * + * Copyright (C) 2006 Ben Dooks <ben@simtec.co.uk> + * Copyright (C) 2006 Simtec Electronics + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. +*/ + +extern __init void ks8695_map_io(void); +extern __init void ks8695_init_irq(void); +extern struct sys_timer ks8695_timer; diff --git a/arch/arm/mach-ks8695/irq.c b/arch/arm/mach-ks8695/irq.c new file mode 100644 index 00000000000..2407bba0054 --- /dev/null +++ b/arch/arm/mach-ks8695/irq.c @@ -0,0 +1,175 @@ +/* + * arch/arm/mach-ks8695/irq.c + * + * Copyright (C) 2006 Ben Dooks <ben@simtec.co.uk> + * Copyright (C) 2006 Simtec Electronics + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA + */ + +#include <linux/init.h> +#include <linux/module.h> +#include <linux/interrupt.h> +#include <linux/ioport.h> +#include <linux/ptrace.h> +#include <linux/sysdev.h> + +#include <asm/hardware.h> +#include <asm/irq.h> +#include <asm/io.h> + +#include <asm/mach/irq.h> + +#include <asm/arch/regs-irq.h> +#include <asm/arch/regs-gpio.h> + +static void ks8695_irq_mask(unsigned int irqno) +{ + unsigned long inten; + + inten = __raw_readl(KS8695_IRQ_VA + KS8695_INTEN); + inten &= ~(1 << irqno); + + __raw_writel(inten, KS8695_IRQ_VA + KS8695_INTEN); +} + +static void ks8695_irq_unmask(unsigned int irqno) +{ + unsigned long inten; + + inten = __raw_readl(KS8695_IRQ_VA + KS8695_INTEN); + inten |= (1 << irqno); + + __raw_writel(inten, KS8695_IRQ_VA + KS8695_INTEN); +} + +static void ks8695_irq_ack(unsigned int irqno) +{ + __raw_writel((1 << irqno), KS8695_IRQ_VA + KS8695_INTST); +} + + +static struct irq_chip ks8695_irq_level_chip; +static struct irq_chip ks8695_irq_edge_chip; + + +static int ks8695_irq_set_type(unsigned int irqno, unsigned int type) +{ + unsigned long ctrl, mode; + unsigned short level_triggered = 0; + + ctrl = __raw_readl(KS8695_GPIO_VA + KS8695_IOPC); + + switch (type) { + case IRQT_HIGH: + mode = IOPC_TM_HIGH; + level_triggered = 1; + break; + case IRQT_LOW: + mode = IOPC_TM_LOW; + level_triggered = 1; + break; + case IRQT_RISING: + mode = IOPC_TM_RISING; + break; + case IRQT_FALLING: + mode = IOPC_TM_FALLING; + break; + case IRQT_BOTHEDGE: + mode = IOPC_TM_EDGE; + break; + default: + return -EINVAL; + } + + switch (irqno) { + case KS8695_IRQ_EXTERN0: + ctrl &= ~IOPC_IOEINT0TM; + ctrl |= IOPC_IOEINT0_MODE(mode); + break; + case KS8695_IRQ_EXTERN1: + ctrl &= ~IOPC_IOEINT1TM; + ctrl |= IOPC_IOEINT1_MODE(mode); + break; + case KS8695_IRQ_EXTERN2: + ctrl &= ~IOPC_IOEINT2TM; + ctrl |= IOPC_IOEINT2_MODE(mode); + break; + case KS8695_IRQ_EXTERN3: + ctrl &= ~IOPC_IOEINT3TM; + ctrl |= IOPC_IOEINT3_MODE(mode); + break; + default: + return -EINVAL; + } + + if (level_triggered) { + set_irq_chip(irqno, &ks8695_irq_level_chip); + set_irq_handler(irqno, handle_level_irq); + } + else { + set_irq_chip(irqno, &ks8695_irq_edge_chip); + set_irq_handler(irqno, handle_edge_irq); + } + + __raw_writel(ctrl, KS8695_GPIO_VA + KS8695_IOPC); + return 0; +} + +static struct irq_chip ks8695_irq_level_chip = { + .ack = ks8695_irq_mask, + .mask = ks8695_irq_mask, + .unmask = ks8695_irq_unmask, + .set_type = ks8695_irq_set_type, +}; + +static struct irq_chip ks8695_irq_edge_chip = { + .ack = ks8695_irq_ack, + .mask = ks8695_irq_mask, + .unmask = ks8695_irq_unmask, + .set_type = ks8695_irq_set_type, +}; + +void __init ks8695_init_irq(void) +{ + unsigned int irq; + + /* Disable all interrupts initially */ + __raw_writel(0, KS8695_IRQ_VA + KS8695_INTMC); + __raw_writel(0, KS8695_IRQ_VA + KS8695_INTEN); + + for (irq = 0; irq < NR_IRQS; irq++) { + switch (irq) { + /* Level-triggered interrupts */ + case KS8695_IRQ_BUS_ERROR: + case KS8695_IRQ_UART_MODEM_STATUS: + case KS8695_IRQ_UART_LINE_STATUS: + case KS8695_IRQ_UART_RX: + case KS8695_IRQ_COMM_TX: + case KS8695_IRQ_COMM_RX: + set_irq_chip(irq, &ks8695_irq_level_chip); + set_irq_handler(irq, handle_level_irq); + break; + + /* Edge-triggered interrupts */ + default: + ks8695_irq_ack(irq); /* clear pending bit */ + set_irq_chip(irq, &ks8695_irq_edge_chip); + set_irq_handler(irq, handle_edge_irq); + } + + set_irq_flags(irq, IRQF_VALID); + } +} diff --git a/arch/arm/mach-ks8695/time.c b/arch/arm/mach-ks8695/time.c new file mode 100644 index 00000000000..d2c86e4a72e --- /dev/null +++ b/arch/arm/mach-ks8695/time.c @@ -0,0 +1,114 @@ +/* + * arch/arm/mach-ks8695/time.c + * + * Copyright (C) 2006 Ben Dooks <ben@simtec.co.uk> + * Copyright (C) 2006 Simtec Electronics + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA + */ + +#include <linux/init.h> +#include <linux/interrupt.h> +#include <linux/irq.h> +#include <linux/kernel.h> +#include <linux/sched.h> + +#include <asm/io.h> +#include <asm/mach/time.h> + +#include <asm/arch/regs-timer.h> +#include <asm/arch/regs-irq.h> + +#include "generic.h" + +/* + * Returns number of ms since last clock interrupt. Note that interrupts + * will have been disabled by do_gettimeoffset() + */ +static unsigned long ks8695_gettimeoffset (void) +{ + unsigned long elapsed, tick2, intpending; + + /* + * Get the current number of ticks. Note that there is a race + * condition between us reading the timer and checking for an + * interrupt. We solve this by ensuring that the counter has not + * reloaded between our two reads. + */ + elapsed = __raw_readl(KS8695_TMR_VA + KS8695_T1TC) + __raw_readl(KS8695_TMR_VA + KS8695_T1PD); + do { + tick2 = elapsed; + intpending = __raw_readl(KS8695_IRQ_VA + KS8695_INTST) & (1 << KS8695_IRQ_TIMER1); + elapsed = __raw_readl(KS8695_TMR_VA + KS8695_T1TC) + __raw_readl(KS8695_TMR_VA + KS8695_T1PD); + } while (elapsed > tick2); + + /* Convert to number of ticks expired (not remaining) */ + elapsed = (CLOCK_TICK_RATE / HZ) - elapsed; + + /* Is interrupt pending? If so, then timer has been reloaded already. */ + if (intpending) + elapsed += (CLOCK_TICK_RATE / HZ); + + /* Convert ticks to usecs */ + return (unsigned long)(elapsed * (tick_nsec / 1000)) / LATCH; +} + +/* + * IRQ handler for the timer. + */ +static irqreturn_t ks8695_timer_interrupt(int irq, void *dev_id) +{ + write_seqlock(&xtime_lock); + timer_tick(); + write_sequnlock(&xtime_lock); + + return IRQ_HANDLED; +} + +static struct irqaction ks8695_timer_irq = { + .name = "ks8695_tick", + .flags = IRQF_DISABLED | IRQF_TIMER, + .handler = ks8695_timer_interrupt, +}; + +static void ks8695_timer_setup(void) +{ + unsigned long tmout = CLOCK_TICK_RATE / HZ; + unsigned long tmcon; + + /* disable timer1 */ + tmcon = __raw_readl(KS8695_TMR_VA + KS8695_TMCON); + __raw_writel(tmcon & ~TMCON_T1EN, KS8695_TMR_VA + KS8695_TMCON); + + __raw_writel(tmout / 2, KS8695_TMR_VA + KS8695_T1TC); + __raw_writel(tmout / 2, KS8695_TMR_VA + KS8695_T1PD); + + /* re-enable timer1 */ + __raw_writel(tmcon | TMCON_T1EN, KS8695_TMR_VA + KS8695_TMCON); +} + +static void __init ks8695_timer_init (void) +{ + ks8695_timer_setup(); + + /* Enable timer interrupts */ + setup_irq(KS8695_IRQ_TIMER1, &ks8695_timer_irq); +} + +struct sys_timer ks8695_timer = { + .init = ks8695_timer_init, + .offset = ks8695_gettimeoffset, + .resume = ks8695_timer_setup, +}; diff --git a/arch/arm/mach-omap2/gpmc.c b/arch/arm/mach-omap2/gpmc.c index 54c836a9845..e290b989aa9 100644 --- a/arch/arm/mach-omap2/gpmc.c +++ b/arch/arm/mach-omap2/gpmc.c @@ -54,7 +54,7 @@ static struct resource gpmc_mem_root; static struct resource gpmc_cs_mem[GPMC_CS_NUM]; -static spinlock_t gpmc_mem_lock = SPIN_LOCK_UNLOCKED; +static DEFINE_SPINLOCK(gpmc_mem_lock); static unsigned gpmc_cs_map; static void __iomem *gpmc_base = diff --git a/arch/arm/mach-pnx4008/dma.c b/arch/arm/mach-pnx4008/dma.c index d6a279e4b52..f7009d845be 100644 --- a/arch/arm/mach-pnx4008/dma.c +++ b/arch/arm/mach-pnx4008/dma.c @@ -47,7 +47,7 @@ static struct ll_pool { int count; } ll_pool; -static spinlock_t ll_lock = SPIN_LOCK_UNLOCKED; +static DEFINE_SPINLOCK(ll_lock); struct pnx4008_dma_ll *pnx4008_alloc_ll_entry(dma_addr_t * ll_dma) { @@ -135,7 +135,7 @@ static inline void dma_decrement_usage(void) } } -static spinlock_t dma_lock = SPIN_LOCK_UNLOCKED; +static DEFINE_SPINLOCK(dma_lock); static inline void pnx4008_dma_lock(void) { diff --git a/arch/arm/mach-pxa/trizeps4.c b/arch/arm/mach-pxa/trizeps4.c index 119c64b7223..28c79bd0a3a 100644 --- a/arch/arm/mach-pxa/trizeps4.c +++ b/arch/arm/mach-pxa/trizeps4.c @@ -24,6 +24,7 @@ #include <linux/delay.h> #include <linux/serial_8250.h> #include <linux/mtd/mtd.h> +#include <linux/mtd/physmap.h> #include <linux/mtd/partitions.h> #include <asm/types.h> @@ -55,23 +56,31 @@ static struct mtd_partition trizeps4_partitions[] = { { .name = "Bootloader", + .offset = 0x00000000, .size = 0x00040000, - .offset = 0, .mask_flags = MTD_WRITEABLE /* force read-only */ },{ - .name = "Kernel", - .size = 0x00400000, - .offset = 0x00040000 + .name = "Backup", + .offset = 0x00040000, + .size = 0x00040000, + },{ + .name = "Image", + .offset = 0x00080000, + .size = 0x01080000, + },{ + .name = "IPSM", + .offset = 0x01100000, + .size = 0x00e00000, },{ - .name = "Filesystem", + .name = "Registry", + .offset = 0x01f00000, .size = MTDPART_SIZ_FULL, - .offset = 0x00440000 } }; -static struct flash_platform_data trizeps4_flash_data[] = { +static struct physmap_flash_data trizeps4_flash_data[] = { { - .map_name = "cfi_probe", + .width = 4, /* bankwidth in bytes */ .parts = trizeps4_partitions, .nr_parts = ARRAY_SIZE(trizeps4_partitions) } @@ -79,15 +88,15 @@ static struct flash_platform_data trizeps4_flash_data[] = { static struct resource flash_resource = { .start = PXA_CS0_PHYS, - .end = PXA_CS0_PHYS + SZ_64M - 1, + .end = PXA_CS0_PHYS + SZ_32M - 1, .flags = IORESOURCE_MEM, }; static struct platform_device flash_device = { - .name = "pxa2xx-flash", + .name = "physmap-flash", .id = 0, .dev = { - .platform_data = &trizeps4_flash_data, + .platform_data = trizeps4_flash_data, }, .resource = &flash_resource, .num_resources = 1, @@ -393,11 +402,37 @@ static struct pxafb_mach_info sharp_lcd = { .pxafb_backlight_power = board_backlight_power, }; +static struct pxafb_mode_info toshiba_lcd_mode = { + .pixclock = 39720, + .xres = 640, + .yres = 480, + .bpp = 8, + .hsync_len = 63, + .left_margin = 12, + .right_margin = 12, + .vsync_len = 4, + .upper_margin = 32, + .lower_margin = 10, + .sync = 0, + .cmap_greyscale = 0, +}; + +static struct pxafb_mach_info toshiba_lcd = { + .modes = &toshiba_lcd_mode, + .num_modes = 1, + .cmap_inverse = 0, + .cmap_static = 0, + .lccr0 = LCCR0_Color | LCCR0_Act, + .lccr3 = 0x03400002, + .pxafb_backlight_power = board_backlight_power, +}; + static void __init trizeps4_init(void) { platform_add_devices(trizeps4_devices, ARRAY_SIZE(trizeps4_devices)); - set_pxa_fb_info(&sharp_lcd); +/* set_pxa_fb_info(&sharp_lcd); */ + set_pxa_fb_info(&toshiba_lcd); pxa_set_mci_info(&trizeps4_mci_platform_data); pxa_set_ficp_info(&trizeps4_ficp_platform_data); @@ -436,9 +471,10 @@ static void __init trizeps4_map_io(void) /* whats that for ??? */ pxa_gpio_mode(GPIO79_nCS_3_MD); +#ifdef CONFIG_LEDS pxa_gpio_mode( GPIO_SYS_BUSY_LED | GPIO_OUT); /* LED1 */ pxa_gpio_mode( GPIO_HEARTBEAT_LED | GPIO_OUT); /* LED2 */ - +#endif #ifdef CONFIG_MACH_TRIZEPS4_CONXS #ifdef CONFIG_IDE_PXA_CF /* if boot direct from compact flash dont disable power */ diff --git a/arch/arm/mach-s3c2410/Makefile b/arch/arm/mach-s3c2410/Makefile index 9a3d3d24c08..3e7a85594d9 100644 --- a/arch/arm/mach-s3c2410/Makefile +++ b/arch/arm/mach-s3c2410/Makefile @@ -20,7 +20,7 @@ obj-$(CONFIG_S3C2410_CLOCK) += clock.o # Machine support obj-$(CONFIG_ARCH_SMDK2410) += mach-smdk2410.o -obj-$(CONFIG_ARCH_H1940) += mach-h1940.o +obj-$(CONFIG_ARCH_H1940) += mach-h1940.o h1940-bluetooth.o obj-$(CONFIG_PM_H1940) += pm-h1940.o obj-$(CONFIG_MACH_N30) += mach-n30.o obj-$(CONFIG_ARCH_BAST) += mach-bast.o usb-simtec.o diff --git a/arch/arm/mach-s3c2410/h1940-bluetooth.c b/arch/arm/mach-s3c2410/h1940-bluetooth.c new file mode 100644 index 00000000000..3c48886521e --- /dev/null +++ b/arch/arm/mach-s3c2410/h1940-bluetooth.c @@ -0,0 +1,142 @@ +/* + * arch/arm/mach-s3c2410/h1940-bluetooth.c + * Copyright (c) Arnaud Patard <arnaud.patard@rtp-net.org> + * + * This file is subject to the terms and conditions of the GNU General Public + * License. See the file COPYING in the main directory of this archive for + * more details. + * + * S3C2410 bluetooth "driver" + * + */ + +#include <linux/module.h> +#include <linux/platform_device.h> +#include <linux/delay.h> +#include <linux/string.h> +#include <linux/ctype.h> +#include <linux/leds.h> +#include <asm/arch/regs-gpio.h> +#include <asm/hardware.h> +#include <asm/arch/h1940-latch.h> + +#define DRV_NAME "h1940-bt" + +#ifdef CONFIG_LEDS_H1940 +DEFINE_LED_TRIGGER(bt_led_trigger); +#endif + +static int state; + +/* Bluetooth control */ +static void h1940bt_enable(int on) +{ + if (on) { +#ifdef CONFIG_LEDS_H1940 + /* flashing Blue */ + led_trigger_event(bt_led_trigger, LED_HALF); +#endif + + /* Power on the chip */ + h1940_latch_control(0, H1940_LATCH_BLUETOOTH_POWER); + /* Reset the chip */ + mdelay(10); + s3c2410_gpio_setpin(S3C2410_GPH1, 1); + mdelay(10); + s3c2410_gpio_setpin(S3C2410_GPH1, 0); + + state = 1; + } + else { +#ifdef CONFIG_LEDS_H1940 + led_trigger_event(bt_led_trigger, 0); +#endif + + s3c2410_gpio_setpin(S3C2410_GPH1, 1); + mdelay(10); + s3c2410_gpio_setpin(S3C2410_GPH1, 0); + mdelay(10); + h1940_latch_control(H1940_LATCH_BLUETOOTH_POWER, 0); + + state = 0; + } +} + +static ssize_t h1940bt_show(struct device *dev, struct device_attribute *attr, char *buf) +{ + return snprintf(buf, PAGE_SIZE, "%d\n", state); +} + +static ssize_t h1940bt_store(struct device *dev, struct device_attribute *attr, const char *buf, size_t count) +{ + int new_state; + char *endp; + + new_state = simple_strtoul(buf, &endp, 0); + if (*endp && !isspace(*endp)) + return -EINVAL; + + h1940bt_enable(new_state); + + return count; +} +static DEVICE_ATTR(enable, 0644, + h1940bt_show, + h1940bt_store); + +static int __init h1940bt_probe(struct platform_device *pdev) +{ + /* Configures BT serial port GPIOs */ + s3c2410_gpio_cfgpin(S3C2410_GPH0, S3C2410_GPH0_nCTS0); + s3c2410_gpio_pullup(S3C2410_GPH0, 1); + s3c2410_gpio_cfgpin(S3C2410_GPH1, S3C2410_GPH1_OUTP); + s3c2410_gpio_pullup(S3C2410_GPH1, 1); + s3c2410_gpio_cfgpin(S3C2410_GPH2, S3C2410_GPH2_TXD0); + s3c2410_gpio_pullup(S3C2410_GPH2, 1); + s3c2410_gpio_cfgpin(S3C2410_GPH3, S3C2410_GPH3_RXD0); + s3c2410_gpio_pullup(S3C2410_GPH3, 1); + +#ifdef CONFIG_LEDS_H1940 + led_trigger_register_simple("h1940-bluetooth", &bt_led_trigger); +#endif + + /* disable BT by default */ + h1940bt_enable(0); + + return device_create_file(&pdev->dev, &dev_attr_enable); +} + +static int h1940bt_remove(struct platform_device *pdev) +{ +#ifdef CONFIG_LEDS_H1940 + led_trigger_unregister_simple(bt_led_trigger); +#endif + return 0; +} + + +static struct platform_driver h1940bt_driver = { + .driver = { + .name = DRV_NAME, + }, + .probe = h1940bt_probe, + .remove = h1940bt_remove, +}; + + +static int __init h1940bt_init(void) +{ + return platform_driver_register(&h1940bt_driver); +} + +static void __exit h1940bt_exit(void) +{ + platform_driver_unregister(&h1940bt_driver); +} + +module_init(h1940bt_init); +module_exit(h1940bt_exit); + +MODULE_AUTHOR("Arnaud Patard <arnaud.patard@rtp-net.org>"); +MODULE_DESCRIPTION("Driver for the iPAQ H1940 bluetooth chip"); +MODULE_LICENSE("GPL"); diff --git a/arch/arm/mach-s3c2410/mach-h1940.c b/arch/arm/mach-s3c2410/mach-h1940.c index 5d5f00e9c46..5ccd0be23a3 100644 --- a/arch/arm/mach-s3c2410/mach-h1940.c +++ b/arch/arm/mach-s3c2410/mach-h1940.c @@ -177,6 +177,11 @@ static struct platform_device s3c_device_leds = { .id = -1, }; +static struct platform_device s3c_device_bluetooth = { + .name = "h1940-bt", + .id = -1, +}; + static struct platform_device *h1940_devices[] __initdata = { &s3c_device_usb, &s3c_device_lcd, @@ -185,6 +190,7 @@ static struct platform_device *h1940_devices[] __initdata = { &s3c_device_iis, &s3c_device_usbgadget, &s3c_device_leds, + &s3c_device_bluetooth, }; static void __init h1940_map_io(void) diff --git a/arch/arm/mach-s3c2443/clock.c b/arch/arm/mach-s3c2443/clock.c index dd2272fb113..0b6e360aeae 100644 --- a/arch/arm/mach-s3c2443/clock.c +++ b/arch/arm/mach-s3c2443/clock.c @@ -791,6 +791,10 @@ static struct clk init_clocks[] = { .name = "usb-bus-host", .id = -1, .parent = &clk_usb_bus_host, + }, { .name = "ac97", + .id = -1, + .parent = &clk_p, + .ctrlbit = S3C2443_PCLKCON_AC97, } }; diff --git a/arch/arm/mm/Kconfig b/arch/arm/mm/Kconfig index b81391a4e37..15f0284010c 100644 --- a/arch/arm/mm/Kconfig +++ b/arch/arm/mm/Kconfig @@ -131,8 +131,8 @@ config CPU_ARM920T # ARM922T config CPU_ARM922T bool "Support ARM922T processor" if ARCH_INTEGRATOR - depends on ARCH_LH7A40X || ARCH_INTEGRATOR - default y if ARCH_LH7A40X + depends on ARCH_LH7A40X || ARCH_INTEGRATOR || ARCH_KS8695 + default y if ARCH_LH7A40X || ARCH_KS8695 select CPU_32v4T select CPU_ABRT_EV4T select CPU_CACHE_V4WT @@ -143,7 +143,7 @@ config CPU_ARM922T help The ARM922T is a version of the ARM920T, but with smaller instruction and data caches. It is used in Altera's - Excalibur XA device family. + Excalibur XA device family and Micrel's KS8695 Centaur. Say Y if you want support for the ARM922T processor. Otherwise, say N. @@ -171,8 +171,8 @@ config CPU_ARM925T # ARM926T config CPU_ARM926T bool "Support ARM926T processor" - depends on ARCH_INTEGRATOR || ARCH_VERSATILE_PB || MACH_VERSATILE_AB || ARCH_OMAP730 || ARCH_OMAP16XX || MACH_REALVIEW_EB || ARCH_PNX4008 || ARCH_NETX || CPU_S3C2412 || ARCH_AT91SAM9260 || ARCH_AT91SAM9261 || ARCH_AT91SAM9263 || ARCH_NS9XXX - default y if ARCH_VERSATILE_PB || MACH_VERSATILE_AB || ARCH_OMAP730 || ARCH_OMAP16XX || ARCH_PNX4008 || ARCH_NETX || CPU_S3C2412 || ARCH_AT91SAM9260 || ARCH_AT91SAM9261 || ARCH_AT91SAM9263 || ARCH_NS9XXX + depends on ARCH_INTEGRATOR || ARCH_VERSATILE_PB || MACH_VERSATILE_AB || ARCH_OMAP730 || ARCH_OMAP16XX || MACH_REALVIEW_EB || ARCH_PNX4008 || ARCH_NETX || CPU_S3C2412 || ARCH_AT91SAM9260 || ARCH_AT91SAM9261 || ARCH_AT91SAM9263 || ARCH_AT91SAM9RL || ARCH_NS9XXX || ARCH_DAVINCI + default y if ARCH_VERSATILE_PB || MACH_VERSATILE_AB || ARCH_OMAP730 || ARCH_OMAP16XX || ARCH_PNX4008 || ARCH_NETX || CPU_S3C2412 || ARCH_AT91SAM9260 || ARCH_AT91SAM9261 || ARCH_AT91SAM9263 || ARCH_AT91SAM9RL || ARCH_NS9XXX || ARCH_DAVINCI select CPU_32v5 select CPU_ABRT_EV5TJ select CPU_CACHE_VIVT diff --git a/arch/arm/tools/mach-types b/arch/arm/tools/mach-types index b1142ce4ac4..0a9a5e7f62e 100644 --- a/arch/arm/tools/mach-types +++ b/arch/arm/tools/mach-types @@ -12,7 +12,7 @@ # # http://www.arm.linux.org.uk/developer/machines/?action=new # -# Last update: Mon Apr 16 21:01:04 2007 +# Last update: Fri May 11 19:53:41 2007 # # machine_is_xxx CONFIG_xxxx MACH_TYPE_xxx number # @@ -1335,3 +1335,35 @@ at91sam9rlek MACH_AT91SAM9RLEK AT91SAM9RLEK 1326 comtech_router MACH_COMTECH_ROUTER COMTECH_ROUTER 1327 sbc2410x MACH_SBC2410X SBC2410X 1328 at4x0bd MACH_AT4X0BD AT4X0BD 1329 +cbifr MACH_CBIFR CBIFR 1330 +arcom_quantum MACH_ARCOM_QUANTUM ARCOM_QUANTUM 1331 +matrix520 MACH_MATRIX520 MATRIX520 1332 +matrix510 MACH_MATRIX510 MATRIX510 1333 +matrix500 MACH_MATRIX500 MATRIX500 1334 +m501 MACH_M501 M501 1335 +aaeon1270 MACH_AAEON1270 AAEON1270 1336 +matrix500ev MACH_MATRIX500EV MATRIX500EV 1337 +pac500 MACH_PAC500 PAC500 1338 +pnx8181 MACH_PNX8181 PNX8181 1339 +colibri320 MACH_COLIBRI320 COLIBRI320 1340 +aztoolbb MACH_AZTOOLBB AZTOOLBB 1341 +aztoolg2 MACH_AZTOOLG2 AZTOOLG2 1342 +dvlhost MACH_DVLHOST DVLHOST 1343 +zir9200 MACH_ZIR9200 ZIR9200 1344 +zir9260 MACH_ZIR9260 ZIR9260 1345 +cocopah MACH_COCOPAH COCOPAH 1346 +nds MACH_NDS NDS 1347 +rosencrantz MACH_ROSENCRANTZ ROSENCRANTZ 1348 +fttx_odsc MACH_FTTX_ODSC FTTX_ODSC 1349 +classe_r6904 MACH_CLASSE_R6904 CLASSE_R6904 1350 +cam60 MACH_CAM60 CAM60 1351 +mxc30031ads MACH_MXC30031ADS MXC30031ADS 1352 +datacall MACH_DATACALL DATACALL 1353 +at91eb01 MACH_AT91EB01 AT91EB01 1354 +rty MACH_RTY RTY 1355 +dwl2100 MACH_DWL2100 DWL2100 1356 +vinsi MACH_VINSI VINSI 1357 +db88f5281 MACH_DB88F5281 DB88F5281 1358 +csb726 MACH_CSB726 CSB726 1359 +tik27 MACH_TIK27 TIK27 1360 +mx_uc7420 MACH_MX_UC7420 MX_UC7420 1361 |