aboutsummaryrefslogtreecommitdiff
path: root/arch/blackfin/Kconfig
diff options
context:
space:
mode:
Diffstat (limited to 'arch/blackfin/Kconfig')
-rw-r--r--arch/blackfin/Kconfig69
1 files changed, 30 insertions, 39 deletions
diff --git a/arch/blackfin/Kconfig b/arch/blackfin/Kconfig
index 5a097c46bc4..f64d25973a3 100644
--- a/arch/blackfin/Kconfig
+++ b/arch/blackfin/Kconfig
@@ -249,7 +249,7 @@ config MEM_MT48LC8M32B2B5_7
config MEM_MT48LC32M16A2TG_75
bool
- depends on (BFIN527_EZKIT || BFIN532_IP0X)
+ depends on (BFIN527_EZKIT || BFIN532_IP0X || BLACKSTAMP)
default y
source "arch/blackfin/mach-bf527/Kconfig"
@@ -292,7 +292,7 @@ config CLKIN_HZ
int "Frequency of the crystal on the board in Hz"
default "11059200" if BFIN533_STAMP
default "27000000" if BFIN533_EZKIT
- default "25000000" if (BFIN537_STAMP || BFIN527_EZKIT || H8606_HVSISTEMAS)
+ default "25000000" if (BFIN537_STAMP || BFIN527_EZKIT || H8606_HVSISTEMAS || BLACKSTAMP)
default "30000000" if BFIN561_EZKIT
default "24576000" if PNAV10
default "10000000" if BFIN532_IP0X
@@ -332,7 +332,7 @@ config VCO_MULT
default "22" if BFIN533_BLUETECHNIX_CM
default "20" if (BFIN537_BLUETECHNIX_CM || BFIN527_BLUETECHNIX_CM || BFIN561_BLUETECHNIX_CM)
default "20" if BFIN561_EZKIT
- default "16" if H8606_HVSISTEMAS
+ default "16" if (H8606_HVSISTEMAS || BLACKSTAMP)
help
This controls the frequency of the on-chip PLL. This can be between 1 and 64.
PLL Frequency = (Crystal Frequency) * (this setting)
@@ -622,6 +622,33 @@ config CPLB_SWITCH_TAB_L1
If enabled, the CPLB Switch Tables are linked
into L1 data memory. (less latency)
+comment "Speed Optimizations"
+config BFIN_INS_LOWOVERHEAD
+ bool "ins[bwl] low overhead, higher interrupt latency"
+ default y
+ help
+ Reads on the Blackfin are speculative. In Blackfin terms, this means
+ they can be interrupted at any time (even after they have been issued
+ on to the external bus), and re-issued after the interrupt occurs.
+ For memory - this is not a big deal, since memory does not change if
+ it sees a read.
+
+ If a FIFO is sitting on the end of the read, it will see two reads,
+ when the core only sees one since the FIFO receives both the read
+ which is cancelled (and not delivered to the core) and the one which
+ is re-issued (which is delivered to the core).
+
+ To solve this, interrupts are turned off before reads occur to
+ I/O space. This option controls which the overhead/latency of
+ controlling interrupts during this time
+ "n" turns interrupts off every read
+ (higher overhead, but lower interrupt latency)
+ "y" turns interrupts off every loop
+ (low overhead, but longer interrupt latency)
+
+ default behavior is to leave this set to on (type "Y"). If you are experiencing
+ interrupt latency issues, it is safe and OK to turn this off.
+
endmenu
@@ -933,13 +960,6 @@ endchoice
comment "Possible Suspend Mem / Hibernate Wake-Up Sources"
depends on PM
-config PM_BFIN_WAKE_RTC
- bool "Allow Wake-Up from RESET and on-chip RTC"
- depends on PM
- default n
- help
- Enable RTC Wake-Up (Voltage Regulator Power-Up)
-
config PM_BFIN_WAKE_PH6
bool "Allow Wake-Up from on-chip PHY or PH6 GP"
depends on PM && (BF52x || BF534 || BF536 || BF537)
@@ -947,41 +967,12 @@ config PM_BFIN_WAKE_PH6
help
Enable PHY and PH6 GP Wake-Up (Voltage Regulator Power-Up)
-config PM_BFIN_WAKE_CAN
- bool "Allow Wake-Up from on-chip CAN0/1"
- depends on PM && (BF54x || BF534 || BF536 || BF537)
- default n
- help
- Enable CAN0/1 Wake-Up (Voltage Regulator Power-Up)
-
config PM_BFIN_WAKE_GP
bool "Allow Wake-Up from GPIOs"
depends on PM && BF54x
default n
help
Enable General-Purpose Wake-Up (Voltage Regulator Power-Up)
-
-config PM_BFIN_WAKE_USB
- bool "Allow Wake-Up from on-chip USB"
- depends on PM && (BF54x || BF52x)
- default n
- help
- Enable USB Wake-Up (Voltage Regulator Power-Up)
-
-config PM_BFIN_WAKE_KEYPAD
- bool "Allow Wake-Up from on-chip Keypad"
- depends on PM && BF54x
- default n
- help
- Enable Keypad Wake-Up (Voltage Regulator Power-Up)
-
-config PM_BFIN_WAKE_ROTARY
- bool "Allow Wake-Up from on-chip Rotary"
- depends on PM && BF54x
- default n
- help
- Enable Rotary Wake-Up (Voltage Regulator Power-Up)
-
endmenu
menu "CPU Frequency scaling"