diff options
Diffstat (limited to 'arch/blackfin/mach-bf533')
| -rw-r--r-- | arch/blackfin/mach-bf533/boards/Kconfig | 6 | ||||
| -rw-r--r-- | arch/blackfin/mach-bf533/boards/Makefile | 1 | ||||
| -rw-r--r-- | arch/blackfin/mach-bf533/boards/blackstamp.c | 401 |
3 files changed, 408 insertions, 0 deletions
diff --git a/arch/blackfin/mach-bf533/boards/Kconfig b/arch/blackfin/mach-bf533/boards/Kconfig index 840059241fb..308c98dc5ab 100644 --- a/arch/blackfin/mach-bf533/boards/Kconfig +++ b/arch/blackfin/mach-bf533/boards/Kconfig @@ -14,6 +14,12 @@ config BFIN533_STAMP help BF533-STAMP board support. +config BLACKSTAMP + bool "BlackStamp" + help + Support for the BlackStamp board. Hardware info available at + http://blackfin.uclinux.org/gf/project/blackstamp/ + config BFIN533_BLUETECHNIX_CM bool "Bluetechnix CM-BF533" depends on (BF533) diff --git a/arch/blackfin/mach-bf533/boards/Makefile b/arch/blackfin/mach-bf533/boards/Makefile index b7a1a1d79bd..9afbe72b484 100644 --- a/arch/blackfin/mach-bf533/boards/Makefile +++ b/arch/blackfin/mach-bf533/boards/Makefile @@ -7,4 +7,5 @@ obj-$(CONFIG_BFIN533_STAMP) += stamp.o obj-$(CONFIG_BFIN532_IP0X) += ip0x.o obj-$(CONFIG_BFIN533_EZKIT) += ezkit.o obj-$(CONFIG_BFIN533_BLUETECHNIX_CM) += cm_bf533.o +obj-$(CONFIG_BLACKSTAMP) += blackstamp.o obj-$(CONFIG_H8606_HVSISTEMAS) += H8606.o diff --git a/arch/blackfin/mach-bf533/boards/blackstamp.c b/arch/blackfin/mach-bf533/boards/blackstamp.c new file mode 100644 index 00000000000..d064ded8771 --- /dev/null +++ b/arch/blackfin/mach-bf533/boards/blackstamp.c @@ -0,0 +1,401 @@ +/* + * File: arch/blackfin/mach-bf533/blackstamp.c + * Based on: arch/blackfin/mach-bf533/stamp.c + * Author: Benjamin Matthews <bmat@lle.rochester.edu> + * Aidan Williams <aidan@nicta.com.au> + * + * Created: 2008 + * Description: Board Info File for the BlackStamp + * + * Copyright 2005 National ICT Australia (NICTA) + * Copyright 2004-2008 Analog Devices Inc. + * + * Enter bugs at http://blackfin.uclinux.org/ + * + * More info about the BlackStamp at: + * http://blackfin.uclinux.org/gf/project/blackstamp/ + * + * Licensed under the GPL-2 or later. + */ + +#include <linux/device.h> +#include <linux/platform_device.h> +#include <linux/mtd/mtd.h> +#include <linux/mtd/partitions.h> +#include <linux/mtd/physmap.h> +#include <linux/spi/spi.h> +#include <linux/spi/flash.h> +#include <linux/irq.h> +#include <linux/i2c.h> +#include <asm/dma.h> +#include <asm/bfin5xx_spi.h> +#include <asm/portmux.h> +#include <asm/dpmc.h> + +/* + * Name the Board for the /proc/cpuinfo + */ +const char bfin_board_name[] = "BlackStamp"; + +#if defined(CONFIG_RTC_DRV_BFIN) || defined(CONFIG_RTC_DRV_BFIN_MODULE) +static struct platform_device rtc_device = { + .name = "rtc-bfin", + .id = -1, +}; +#endif + +/* + * Driver needs to know address, irq and flag pin. + */ +#if defined(CONFIG_SMC91X) || defined(CONFIG_SMC91X_MODULE) +static struct resource smc91x_resources[] = { + { + .name = "smc91x-regs", + .start = 0x20300300, + .end = 0x20300300 + 16, + .flags = IORESOURCE_MEM, + }, { + .start = IRQ_PF3, + .end = IRQ_PF3, + .flags = IORESOURCE_IRQ | IORESOURCE_IRQ_HIGHLEVEL, + }, +}; + +static struct platform_device smc91x_device = { + .name = "smc91x", + .id = 0, + .num_resources = ARRAY_SIZE(smc91x_resources), + .resource = smc91x_resources, +}; +#endif + +#if defined(CONFIG_MTD_M25P80) || defined(CONFIG_MTD_M25P80_MODULE) +static struct mtd_partition bfin_spi_flash_partitions[] = { + { + .name = "bootloader(spi)", + .size = 0x00040000, + .offset = 0, + .mask_flags = MTD_CAP_ROM + }, { + .name = "linux kernel(spi)", + .size = 0x180000, + .offset = MTDPART_OFS_APPEND, + }, { + .name = "file system(spi)", + .size = MTDPART_SIZ_FULL, + .offset = MTDPART_OFS_APPEND, + } +}; + +static struct flash_platform_data bfin_spi_flash_data = { + .name = "m25p80", + .parts = bfin_spi_flash_partitions, + .nr_parts = ARRAY_SIZE(bfin_spi_flash_partitions), + .type = "m25p64", +}; + +/* SPI flash chip (m25p64) */ +static struct bfin5xx_spi_chip spi_flash_chip_info = { + .enable_dma = 0, /* use dma transfer with this chip*/ + .bits_per_word = 8, +}; +#endif + +#if defined(CONFIG_SPI_MMC) || defined(CONFIG_SPI_MMC_MODULE) +static struct bfin5xx_spi_chip spi_mmc_chip_info = { + .enable_dma = 1, + .bits_per_word = 8, +}; +#endif + +#if defined(CONFIG_SPI_SPIDEV) || defined(CONFIG_SPI_SPIDEV_MODULE) +static struct bfin5xx_spi_chip spidev_chip_info = { + .enable_dma = 0, + .bits_per_word = 8, +}; +#endif + +static struct spi_board_info bfin_spi_board_info[] __initdata = { +#if defined(CONFIG_MTD_M25P80) || defined(CONFIG_MTD_M25P80_MODULE) + { + /* the modalias must be the same as spi device driver name */ + .modalias = "m25p80", /* Name of spi_driver for this device */ + .max_speed_hz = 20000000, /* max spi clock (SCK) speed in HZ */ + .bus_num = 0, /* Framework bus number */ + .chip_select = 2, /* Framework chip select. */ + .platform_data = &bfin_spi_flash_data, + .controller_data = &spi_flash_chip_info, + .mode = SPI_MODE_3, + }, +#endif + +#if defined(CONFIG_SPI_MMC) || defined(CONFIG_SPI_MMC_MODULE) + { + .modalias = "spi_mmc_dummy", + .max_speed_hz = 20000000, /* max spi clock (SCK) speed in HZ */ + .bus_num = 0, + .chip_select = 0, + .platform_data = NULL, + .controller_data = &spi_mmc_chip_info, + .mode = SPI_MODE_3, + }, + { + .modalias = "spi_mmc", + .max_speed_hz = 20000000, /* max spi clock (SCK) speed in HZ */ + .bus_num = 0, + .chip_select = CONFIG_SPI_MMC_CS_CHAN, + .platform_data = NULL, + .controller_data = &spi_mmc_chip_info, + .mode = SPI_MODE_3, + }, +#endif + +#if defined(CONFIG_SPI_SPIDEV) || defined(CONFIG_SPI_SPIDEV_MODULE) + { + .modalias = "spidev", + .max_speed_hz = 3125000, /* max spi clock (SCK) speed in HZ */ + .bus_num = 0, + .chip_select = 7, + .controller_data = &spidev_chip_info, + }, +#endif +}; + +#if defined(CONFIG_SPI_BFIN) || defined(CONFIG_SPI_BFIN_MODULE) +/* SPI (0) */ +static struct resource bfin_spi0_resource[] = { + [0] = { + .start = SPI0_REGBASE, + .end = SPI0_REGBASE + 0xFF, + .flags = IORESOURCE_MEM, + }, + [1] = { + .start = CH_SPI, + .end = CH_SPI, + .flags = IORESOURCE_IRQ, + } +}; + +/* SPI controller data */ +static struct bfin5xx_spi_master bfin_spi0_info = { + .num_chipselect = 8, + .enable_dma = 1, /* master has the ability to do dma transfer */ + .pin_req = {P_SPI0_SCK, P_SPI0_MISO, P_SPI0_MOSI, 0}, +}; + +static struct platform_device bfin_spi0_device = { + .name = "bfin-spi", + .id = 0, /* Bus number */ + .num_resources = ARRAY_SIZE(bfin_spi0_resource), + .resource = bfin_spi0_resource, + .dev = { + .platform_data = &bfin_spi0_info, /* Passed to driver */ + }, +}; +#endif /* spi master and devices */ + +#if defined(CONFIG_SERIAL_BFIN) || defined(CONFIG_SERIAL_BFIN_MODULE) +static struct resource bfin_uart_resources[] = { + { + .start = 0xFFC00400, + .end = 0xFFC004FF, + .flags = IORESOURCE_MEM, + }, +}; + +static struct platform_device bfin_uart_device = { + .name = "bfin-uart", + .id = 1, + .num_resources = ARRAY_SIZE(bfin_uart_resources), + .resource = bfin_uart_resources, +}; +#endif + +#if defined(CONFIG_BFIN_SIR) || defined(CONFIG_BFIN_SIR_MODULE) +static struct resource bfin_sir_resources[] = { +#ifdef CONFIG_BFIN_SIR0 + { + .start = 0xFFC00400, + .end = 0xFFC004FF, + .flags = IORESOURCE_MEM, + }, +#endif +}; + +static struct platform_device bfin_sir_device = { + .name = "bfin_sir", + .id = 0, + .num_resources = ARRAY_SIZE(bfin_sir_resources), + .resource = bfin_sir_resources, +}; +#endif + +#if defined(CONFIG_SERIAL_BFIN_SPORT) || defined(CONFIG_SERIAL_BFIN_SPORT_MODULE) +static struct platform_device bfin_sport0_uart_device = { + .name = "bfin-sport-uart", + .id = 0, +}; + +static struct platform_device bfin_sport1_uart_device = { + .name = "bfin-sport-uart", + .id = 1, +}; +#endif + +#if defined(CONFIG_KEYBOARD_GPIO) || defined(CONFIG_KEYBOARD_GPIO_MODULE) +#include <linux/input.h> +#include <linux/gpio_keys.h> + +static struct gpio_keys_button bfin_gpio_keys_table[] = { + {BTN_0, GPIO_PF4, 0, "gpio-keys: BTN0"}, + {BTN_1, GPIO_PF5, 0, "gpio-keys: BTN1"}, + {BTN_2, GPIO_PF6, 0, "gpio-keys: BTN2"}, +}; /* Mapped to the first three PF Test Points */ + +static struct gpio_keys_platform_data bfin_gpio_keys_data = { + .buttons = bfin_gpio_keys_table, + .nbuttons = ARRAY_SIZE(bfin_gpio_keys_table), +}; + +static struct platform_device bfin_device_gpiokeys = { + .name = "gpio-keys", + .dev = { + .platform_data = &bfin_gpio_keys_data, + }, +}; +#endif + +static struct resource bfin_gpios_resources = { + .start = 0, + .end = MAX_BLACKFIN_GPIOS - 1, + .flags = IORESOURCE_IRQ, +}; + +static struct platform_device bfin_gpios_device = { + .name = "simple-gpio", + .id = -1, + .num_resources = 1, + .resource = &bfin_gpios_resources, +}; + +#if defined(CONFIG_I2C_GPIO) || defined(CONFIG_I2C_GPIO_MODULE) +#include <linux/i2c-gpio.h> + +static struct i2c_gpio_platform_data i2c_gpio_data = { + .sda_pin = 8, + .scl_pin = 9, + .sda_is_open_drain = 0, + .scl_is_open_drain = 0, + .udelay = 40, +}; /* This hasn't actually been used these pins + * are (currently) free pins on the expansion connector */ + +static struct platform_device i2c_gpio_device = { + .name = "i2c-gpio", + .id = 0, + .dev = { + .platform_data = &i2c_gpio_data, + }, +}; +#endif + +#ifdef CONFIG_I2C_BOARDINFO +static struct i2c_board_info __initdata bfin_i2c_board_info[] = { +}; +#endif + +static const unsigned int cclk_vlev_datasheet[] = +{ + VRPAIR(VLEV_085, 250000000), + VRPAIR(VLEV_090, 376000000), + VRPAIR(VLEV_095, 426000000), + VRPAIR(VLEV_100, 426000000), + VRPAIR(VLEV_105, 476000000), + VRPAIR(VLEV_110, 476000000), + VRPAIR(VLEV_115, 476000000), + VRPAIR(VLEV_120, 600000000), + VRPAIR(VLEV_125, 600000000), + VRPAIR(VLEV_130, 600000000), +}; + +static struct bfin_dpmc_platform_data bfin_dmpc_vreg_data = { + .tuple_tab = cclk_vlev_datasheet, + .tabsize = ARRAY_SIZE(cclk_vlev_datasheet), + .vr_settling_time = 25 /* us */, +}; + +static struct platform_device bfin_dpmc = { + .name = "bfin dpmc", + .dev = { + .platform_data = &bfin_dmpc_vreg_data, + }, +}; + +static struct platform_device *stamp_devices[] __initdata = { + + &bfin_dpmc, + +#if defined(CONFIG_RTC_DRV_BFIN) || defined(CONFIG_RTC_DRV_BFIN_MODULE) + &rtc_device, +#endif + +#if defined(CONFIG_SMC91X) || defined(CONFIG_SMC91X_MODULE) + &smc91x_device, +#endif + + +#if defined(CONFIG_SPI_BFIN) || defined(CONFIG_SPI_BFIN_MODULE) + &bfin_spi0_device, +#endif + +#if defined(CONFIG_SERIAL_BFIN) || defined(CONFIG_SERIAL_BFIN_MODULE) + &bfin_uart_device, +#endif + +#if defined(CONFIG_BFIN_SIR) || defined(CONFIG_BFIN_SIR_MODULE) + &bfin_sir_device, +#endif + +#if defined(CONFIG_SERIAL_BFIN_SPORT) || defined(CONFIG_SERIAL_BFIN_SPORT_MODULE) + &bfin_sport0_uart_device, + &bfin_sport1_uart_device, +#endif + +#if defined(CONFIG_KEYBOARD_GPIO) || defined(CONFIG_KEYBOARD_GPIO_MODULE) + &bfin_device_gpiokeys, +#endif + +#if defined(CONFIG_I2C_GPIO) || defined(CONFIG_I2C_GPIO_MODULE) + &i2c_gpio_device, +#endif + + &bfin_gpios_device, +}; + +static int __init blackstamp_init(void) +{ + int ret; + + printk(KERN_INFO "%s(): registering device resources\n", __func__); + +#ifdef CONFIG_I2C_BOARDINFO + i2c_register_board_info(0, bfin_i2c_board_info, + ARRAY_SIZE(bfin_i2c_board_info)); +#endif + + ret = platform_add_devices(stamp_devices, ARRAY_SIZE(stamp_devices)); + if (ret < 0) + return ret; + +#if defined(CONFIG_SMC91X) || defined(CONFIG_SMC91X_MODULE) + /* setup BF533_STAMP CPLD to route AMS3 to Ethernet MAC */ + bfin_write_FIO_DIR(bfin_read_FIO_DIR() | PF0); + bfin_write_FIO_FLAG_S(PF0); + SSYNC(); +#endif + + spi_register_board_info(bfin_spi_board_info, ARRAY_SIZE(bfin_spi_board_info)); + return 0; +} + +arch_initcall(blackstamp_init); |