6 files changed, 11 insertions, 11 deletions
diff --git a/arch/cris/arch-v10/Kconfig b/arch/cris/arch-v10/Kconfig
index 44eb1b9accb..c7ea9efd010 100644
--- a/arch/cris/arch-v10/Kconfig
+++ b/arch/cris/arch-v10/Kconfig
@@ -323,7 +323,7 @@ config ETRAX_DEF_R_WAITSTATES
 	depends on ETRAX_ARCH_V10
 	default "95a6"
 	help
-	  Waitstates for SRAM, Flash and peripherials (not DRAM).  95f8 is a
+	  Waitstates for SRAM, Flash and peripherals (not DRAM).  95f8 is a
 	  good choice for most Axis products...
 
 config ETRAX_DEF_R_BUS_CONFIG
diff --git a/arch/cris/arch-v10/drivers/Kconfig b/arch/cris/arch-v10/drivers/Kconfig
index 734d5f3a530..e7e724bc0ba 100644
--- a/arch/cris/arch-v10/drivers/Kconfig
+++ b/arch/cris/arch-v10/drivers/Kconfig
@@ -839,7 +839,7 @@ config ETRAX_DS1302_TRICKLE_CHARGE
 	default "0"
 	help
 	  This controls the initial value of the trickle charge register.
-	  0 = disabled (use this if you are unsure or have a non rechargable battery)
+	  0 = disabled (use this if you are unsure or have a non rechargeable battery)
 	  Otherwise the following values can be OR:ed together to control the
 	  charge current:
 	  1 = 2kohm, 2 = 4kohm, 3 = 4kohm
diff --git a/arch/cris/arch-v10/drivers/eeprom.c b/arch/cris/arch-v10/drivers/eeprom.c
index 6e1f191a71e..284ebfda03f 100644
--- a/arch/cris/arch-v10/drivers/eeprom.c
+++ b/arch/cris/arch-v10/drivers/eeprom.c
@@ -1,7 +1,7 @@
 /*!*****************************************************************************
 *!
-*!  Implements an interface for i2c compatible eeproms to run under linux.
-*!  Supports 2k, 8k(?) and 16k. Uses adaptive timing adjustents by
+*!  Implements an interface for i2c compatible eeproms to run under Linux.
+*!  Supports 2k, 8k(?) and 16k. Uses adaptive timing adjustments by
 *!  Johan.Adolfsson@axis.com
 *!
 *!  Probing results:
@@ -51,7 +51,7 @@
 *!  Revision 1.8  2001/06/15 13:24:29  jonashg
 *!  * Added verification of pointers from userspace in read and write.
 *!  * Made busy counter volatile.
-*!  * Added define for inital write delay.
+*!  * Added define for initial write delay.
 *!  * Removed warnings by using loff_t instead of unsigned long.
 *!
 *!  Revision 1.7  2001/06/14 15:26:54  jonashg
diff --git a/arch/cris/arch-v10/drivers/i2c.c b/arch/cris/arch-v10/drivers/i2c.c
index 6114596c3b3..092c724a645 100644
--- a/arch/cris/arch-v10/drivers/i2c.c
+++ b/arch/cris/arch-v10/drivers/i2c.c
@@ -47,7 +47,7 @@
 *! Update Port B register and shadow even when running with hardware support
 *!   to avoid glitches when reading bits
 *! Never set direction to out in i2c_inbyte
-*! Removed incorrect clock togling at end of i2c_inbyte
+*! Removed incorrect clock toggling at end of i2c_inbyte
 *!
 *! Revision 1.8  2002/08/13 06:31:53  starvik
 *! Made SDA and SCL line configurable
diff --git a/arch/cris/arch-v10/kernel/kgdb.c b/arch/cris/arch-v10/kernel/kgdb.c
index 34528da9881..07628a13c6c 100644
--- a/arch/cris/arch-v10/kernel/kgdb.c
+++ b/arch/cris/arch-v10/kernel/kgdb.c
@@ -33,7 +33,7 @@
 *!
 *! Revision 1.2  2002/11/19 14:35:24  starvik
 *! Changes from linux 2.4
-*! Changed struct initializer syntax to the currently prefered notation
+*! Changed struct initializer syntax to the currently preferred notation
 *!
 *! Revision 1.1  2001/12/17 13:59:27  bjornw
 *! Initial revision
diff --git a/arch/cris/arch-v32/drivers/Kconfig b/arch/cris/arch-v32/drivers/Kconfig
index a33097f9536..f64624fc450 100644
--- a/arch/cris/arch-v32/drivers/Kconfig
+++ b/arch/cris/arch-v32/drivers/Kconfig
@@ -88,7 +88,7 @@ config ETRAX_SERIAL_PORT0_DMA7_IN
 	help
 	  Enables the DMA7 input channel for ser0 (ttyS0).
 	  If you do not enable DMA, an interrupt for each character will be
-	  used when receiveing data.
+	  used when receiving data.
 	  Normally you want to use DMA, unless you use the DMA channel for
 	  something else.
 
@@ -157,7 +157,7 @@ config ETRAX_SERIAL_PORT1_DMA5_IN
 	help
 	  Enables the DMA5 input channel for ser1 (ttyS1).
 	  If you do not enable DMA, an interrupt for each character will be
-	  used when receiveing data.
+	  used when receiving data.
 	  Normally you want this on, unless you use the DMA channel for
 	  something else.
 
@@ -228,7 +228,7 @@ config ETRAX_SERIAL_PORT2_DMA3_IN
 	help
 	  Enables the DMA3 input channel for ser2 (ttyS2).
 	  If you do not enable DMA, an interrupt for each character will be
-	  used when receiveing data.
+	  used when receiving data.
 	  Normally you want to use DMA, unless you use the DMA channel for
 	  something else.
 
@@ -297,7 +297,7 @@ config ETRAX_SERIAL_PORT3_DMA9_IN
 	help
 	  Enables the DMA9 input channel for ser3 (ttyS3).
 	  If you do not enable DMA, an interrupt for each character will be
-	  used when receiveing data.
+	  used when receiving data.
 	  Normally you want to use DMA, unless you use the DMA channel for
 	  something else.