diff options
Diffstat (limited to 'arch/sh/drivers/pci')
35 files changed, 869 insertions, 1982 deletions
diff --git a/arch/sh/drivers/pci/Kconfig b/arch/sh/drivers/pci/Kconfig index 7e816ededed..e8db585a663 100644 --- a/arch/sh/drivers/pci/Kconfig +++ b/arch/sh/drivers/pci/Kconfig @@ -17,21 +17,3 @@ config SH_PCIDMA_NONCOHERENT code will not have to flush the CPU's caches. If you have a PCI host bridge integrated with your SH CPU, refer carefully to the chip specs to see if you can say 'N' here. Otherwise, leave it as 'Y'. - -# This is also board-specific -config PCI_AUTO - bool - depends on PCI - default y - -config PCI_AUTO_UPDATE_RESOURCES - bool - depends on PCI_AUTO - default y if !SH_DREAMCAST - help - Selecting this option will cause the PCI auto code to leave your - BAR values alone. Otherwise they will be updated automatically. If - for some reason, you have a board that simply refuses to work - with its resources updated beyond what they are when the device - is powered up, set this to N. Everyone else will want this as Y. - diff --git a/arch/sh/drivers/pci/Makefile b/arch/sh/drivers/pci/Makefile index 847e90894d1..d2ffc477549 100644 --- a/arch/sh/drivers/pci/Makefile +++ b/arch/sh/drivers/pci/Makefile @@ -1,9 +1,7 @@ # # Makefile for the PCI specific kernel interface routines under Linux. # - obj-y += pci.o -obj-$(CONFIG_PCI_AUTO) += pci-auto.o obj-$(CONFIG_CPU_SUBTYPE_SH7751) += pci-sh7751.o ops-sh4.o obj-$(CONFIG_CPU_SUBTYPE_SH7751R) += pci-sh7751.o ops-sh4.o @@ -12,15 +10,17 @@ obj-$(CONFIG_CPU_SUBTYPE_SH7780) += pci-sh7780.o ops-sh4.o obj-$(CONFIG_CPU_SUBTYPE_SH7785) += pci-sh7780.o ops-sh4.o obj-$(CONFIG_CPU_SH5) += pci-sh5.o ops-sh5.o -obj-$(CONFIG_SH_DREAMCAST) += ops-dreamcast.o fixups-dreamcast.o -obj-$(CONFIG_SH_SECUREEDGE5410) += ops-snapgear.o -obj-$(CONFIG_SH_RTS7751R2D) += ops-rts7751r2d.o fixups-rts7751r2d.o -obj-$(CONFIG_SH_SH03) += ops-sh03.o fixups-sh03.o -obj-$(CONFIG_SH_HIGHLANDER) += ops-r7780rp.o fixups-r7780rp.o -obj-$(CONFIG_SH_SDK7780) += ops-sdk7780.o fixups-sdk7780.o -obj-$(CONFIG_SH_TITAN) += ops-titan.o -obj-$(CONFIG_SH_LANDISK) += ops-landisk.o -obj-$(CONFIG_SH_LBOX_RE2) += ops-lboxre2.o fixups-lboxre2.o -obj-$(CONFIG_SH_7780_SOLUTION_ENGINE) += ops-se7780.o fixups-se7780.o -obj-$(CONFIG_SH_CAYMAN) += ops-cayman.o -obj-$(CONFIG_SH_SH7785LCR) += ops-sh7785lcr.o fixups-sh7785lcr.o +obj-$(CONFIG_SH_DREAMCAST) += ops-dreamcast.o fixups-dreamcast.o \ + pci-dreamcast.o +obj-$(CONFIG_SH_SECUREEDGE5410) += fixups-snapgear.o +obj-$(CONFIG_SH_7751_SOLUTION_ENGINE) += fixups-se7751.o +obj-$(CONFIG_SH_RTS7751R2D) += fixups-rts7751r2d.o +obj-$(CONFIG_SH_SH03) += fixups-sh03.o +obj-$(CONFIG_SH_HIGHLANDER) += fixups-r7780rp.o +obj-$(CONFIG_SH_SH7785LCR) += fixups-r7780rp.o +obj-$(CONFIG_SH_SDK7780) += fixups-sdk7780.o +obj-$(CONFIG_SH_7780_SOLUTION_ENGINE) += fixups-sdk7780.o +obj-$(CONFIG_SH_TITAN) += fixups-titan.o +obj-$(CONFIG_SH_LANDISK) += fixups-landisk.o +obj-$(CONFIG_SH_LBOX_RE2) += fixups-rts7751r2d.o +obj-$(CONFIG_SH_CAYMAN) += fixups-cayman.o diff --git a/arch/sh/drivers/pci/ops-cayman.c b/arch/sh/drivers/pci/fixups-cayman.c index 38ef76207af..b68b61d22c6 100644 --- a/arch/sh/drivers/pci/ops-cayman.c +++ b/arch/sh/drivers/pci/fixups-cayman.c @@ -75,15 +75,3 @@ int __init pcibios_map_platform_irq(struct pci_dev *dev, u8 slot, u8 pin) return result; } - -struct pci_channel board_pci_channels[] = { - { &sh5_pci_ops, NULL, NULL, 0, 0xff }, - { NULL, NULL, NULL, 0, 0 }, -}; -EXPORT_SYMBOL(board_pci_channels); - -int __init pcibios_init_platform(void) -{ - return sh5pci_init(__pa(memory_start), - __pa(memory_end) - __pa(memory_start)); -} diff --git a/arch/sh/drivers/pci/fixups-dreamcast.c b/arch/sh/drivers/pci/fixups-dreamcast.c index 2bf85cf091e..ed7f489936f 100644 --- a/arch/sh/drivers/pci/fixups-dreamcast.c +++ b/arch/sh/drivers/pci/fixups-dreamcast.c @@ -30,7 +30,7 @@ static void __init gapspci_fixup_resources(struct pci_dev *dev) { - struct pci_channel *p = board_pci_channels; + struct pci_channel *p = dev->sysdata; printk(KERN_NOTICE "PCI: Fixing up device %s\n", pci_name(dev)); @@ -41,6 +41,13 @@ static void __init gapspci_fixup_resources(struct pci_dev *dev) */ dev->resource[1].start = p->io_resource->start + 0x100; dev->resource[1].end = dev->resource[1].start + 0x200 - 1; + + /* + * This is not a normal BAR, prevent any attempts to move + * the BAR, as this will result in a bus lock. + */ + dev->resource[1].flags |= IORESOURCE_PCI_FIXED; + /* * Redirect dma memory allocations to special memory window. */ diff --git a/arch/sh/drivers/pci/ops-landisk.c b/arch/sh/drivers/pci/fixups-landisk.c index bff09ecf341..bb1a6bb5149 100644 --- a/arch/sh/drivers/pci/ops-landisk.c +++ b/arch/sh/drivers/pci/fixups-landisk.c @@ -15,39 +15,6 @@ #include <linux/pci.h> #include "pci-sh4.h" -static struct resource sh7751_io_resource = { - .name = "SH7751 IO", - .start = SH7751_PCI_IO_BASE, - .end = SH7751_PCI_IO_BASE + SH7751_PCI_IO_SIZE - 1, - .flags = IORESOURCE_IO -}; - -static struct resource sh7751_mem_resource = { - .name = "SH7751 mem", - .start = SH7751_PCI_MEMORY_BASE, - .end = SH7751_PCI_MEMORY_BASE + SH7751_PCI_MEM_SIZE - 1, - .flags = IORESOURCE_MEM -}; - -struct pci_channel board_pci_channels[] = { - {&sh4_pci_ops, &sh7751_io_resource, &sh7751_mem_resource, 0, 0x3ff}, - {NULL, NULL, NULL, 0, 0}, -}; - -static struct sh4_pci_address_map sh7751_pci_map = { - .window0 = { - .base = SH7751_CS3_BASE_ADDR, - .size = (64 << 20), /* 64MB */ - }, - - .flags = SH4_PCIC_NO_RESET, -}; - -int __init pcibios_init_platform(void) -{ - return sh7751_pcic_init(&sh7751_pci_map); -} - int pcibios_map_platform_irq(struct pci_dev *pdev, u8 slot, u8 pin) { /* diff --git a/arch/sh/drivers/pci/fixups-lboxre2.c b/arch/sh/drivers/pci/fixups-lboxre2.c deleted file mode 100644 index 1c1d41255ec..00000000000 --- a/arch/sh/drivers/pci/fixups-lboxre2.c +++ /dev/null @@ -1,41 +0,0 @@ -/* - * arch/sh/drivers/pci/fixups-lboxre2.c - * - * L-BOX RE2 PCI fixups - * - * Copyright (C) 2007 Nobuhiro Iwamatsu - * - * This file is subject to the terms and conditions of the GNU General Public - * License. See the file "COPYING" in the main directory of this archive - * for more details. - */ -#include "pci-sh4.h" - -#define PCIMCR_MRSET_OFF 0xBFFFFFFF -#define PCIMCR_RFSH_OFF 0xFFFFFFFB - -int pci_fixup_pcic(void) -{ - unsigned long bcr1, mcr; - - bcr1 = ctrl_inl(SH7751_BCR1); - bcr1 |= 0x40080000; /* Enable Bit 19 BREQEN, set PCIC to slave */ - pci_write_reg(bcr1, SH4_PCIBCR1); - - /* Enable all interrupts, so we known what to fix */ - pci_write_reg(0x0000c3ff, SH4_PCIINTM); - pci_write_reg(0x0000380f, SH4_PCIAINTM); - pci_write_reg(0xfb900047, SH7751_PCICONF1); - pci_write_reg(0xab000001, SH7751_PCICONF4); - - mcr = ctrl_inl(SH7751_MCR); - mcr = (mcr & PCIMCR_MRSET_OFF) & PCIMCR_RFSH_OFF; - pci_write_reg(mcr, SH4_PCIMCR); - - pci_write_reg(0x0c000000, SH7751_PCICONF5); - pci_write_reg(0xd0000000, SH7751_PCICONF6); - pci_write_reg(0x0c000000, SH4_PCILAR0); - pci_write_reg(0x00000000, SH4_PCILAR1); - - return 0; -} diff --git a/arch/sh/drivers/pci/fixups-r7780rp.c b/arch/sh/drivers/pci/fixups-r7780rp.c index 3e321df65d2..15ca65cb667 100644 --- a/arch/sh/drivers/pci/fixups-r7780rp.c +++ b/arch/sh/drivers/pci/fixups-r7780rp.c @@ -11,35 +11,26 @@ * for more details. */ #include <linux/pci.h> +#include <linux/io.h> #include "pci-sh4.h" -#include <asm/io.h> -int pci_fixup_pcic(void) -{ - pci_write_reg(0x000043ff, SH4_PCIINTM); - pci_write_reg(0x0000380f, SH4_PCIAINTM); - - pci_write_reg(0xfbb00047, SH7780_PCICMD); - pci_write_reg(0x00000000, SH7780_PCIIBAR); - - pci_write_reg(0x00011912, SH7780_PCISVID); - pci_write_reg(0x08000000, SH7780_PCICSCR0); - pci_write_reg(0x0000001b, SH7780_PCICSAR0); - pci_write_reg(0xfd000000, SH7780_PCICSCR1); - pci_write_reg(0x0000000f, SH7780_PCICSAR1); - - pci_write_reg(0xfd000000, SH7780_PCIMBR0); - pci_write_reg(0x00fc0000, SH7780_PCIMBMR0); +static char irq_tab[] __initdata = { + 65, 66, 67, 68, +}; -#ifdef CONFIG_32BIT - pci_write_reg(0xc0000000, SH7780_PCIMBR2); - pci_write_reg(0x20000000 - SH7780_PCI_IO_SIZE, SH7780_PCIMBMR2); -#endif +int __init pcibios_map_platform_irq(struct pci_dev *pdev, u8 slot, u8 pin) +{ + return irq_tab[slot]; +} - /* Set IOBR for windows containing area specified in pci.h */ - pci_write_reg((PCIBIOS_MIN_IO & ~(SH7780_PCI_IO_SIZE - 1)), - SH7780_PCIIOBR); - pci_write_reg(((SH7780_PCI_IO_SIZE-1) & (7<<18)), SH7780_PCIIOBMR); +int pci_fixup_pcic(struct pci_channel *chan) +{ + pci_write_reg(chan, 0x000043ff, SH4_PCIINTM); + pci_write_reg(chan, 0x00000000, SH7780_PCIIBAR); + pci_write_reg(chan, 0x08000000, SH7780_PCICSCR0); + pci_write_reg(chan, 0x0000001b, SH7780_PCICSAR0); + pci_write_reg(chan, 0xfd000000, SH7780_PCICSCR1); + pci_write_reg(chan, 0x0000000f, SH7780_PCICSAR1); return 0; } diff --git a/arch/sh/drivers/pci/fixups-rts7751r2d.c b/arch/sh/drivers/pci/fixups-rts7751r2d.c index 904bce8768d..052b354236d 100644 --- a/arch/sh/drivers/pci/fixups-rts7751r2d.c +++ b/arch/sh/drivers/pci/fixups-rts7751r2d.c @@ -1,43 +1,67 @@ /* * arch/sh/drivers/pci/fixups-rts7751r2d.c * - * RTS7751R2D PCI fixups + * RTS7751R2D / LBOXRE2 PCI fixups * * Copyright (C) 2003 Lineo uSolutions, Inc. * Copyright (C) 2004 Paul Mundt + * Copyright (C) 2007 Nobuhiro Iwamatsu * * This file is subject to the terms and conditions of the GNU General Public * License. See the file "COPYING" in the main directory of this archive * for more details. */ +#include <linux/pci.h> +#include <mach/lboxre2.h> +#include <mach/r2d.h> #include "pci-sh4.h" +#include <asm/machtypes.h> #define PCIMCR_MRSET_OFF 0xBFFFFFFF #define PCIMCR_RFSH_OFF 0xFFFFFFFB -int pci_fixup_pcic(void) +static u8 rts7751r2d_irq_tab[] __initdata = { + IRQ_PCI_INTA, + IRQ_PCI_INTB, + IRQ_PCI_INTC, + IRQ_PCI_INTD, +}; + +static char lboxre2_irq_tab[] __initdata = { + IRQ_ETH0, IRQ_ETH1, IRQ_INTA, IRQ_INTD, +}; + +int __init pcibios_map_platform_irq(struct pci_dev *pdev, u8 slot, u8 pin) +{ + if (mach_is_lboxre2()) + return lboxre2_irq_tab[slot]; + else + return rts7751r2d_irq_tab[slot]; +} + +int pci_fixup_pcic(struct pci_channel *chan) { unsigned long bcr1, mcr; bcr1 = ctrl_inl(SH7751_BCR1); bcr1 |= 0x40080000; /* Enable Bit 19 BREQEN, set PCIC to slave */ - pci_write_reg(bcr1, SH4_PCIBCR1); + pci_write_reg(chan, bcr1, SH4_PCIBCR1); /* Enable all interrupts, so we known what to fix */ - pci_write_reg(0x0000c3ff, SH4_PCIINTM); - pci_write_reg(0x0000380f, SH4_PCIAINTM); + pci_write_reg(chan, 0x0000c3ff, SH4_PCIINTM); + pci_write_reg(chan, 0x0000380f, SH4_PCIAINTM); - pci_write_reg(0xfb900047, SH7751_PCICONF1); - pci_write_reg(0xab000001, SH7751_PCICONF4); + pci_write_reg(chan, 0xfb900047, SH7751_PCICONF1); + pci_write_reg(chan, 0xab000001, SH7751_PCICONF4); mcr = ctrl_inl(SH7751_MCR); mcr = (mcr & PCIMCR_MRSET_OFF) & PCIMCR_RFSH_OFF; - pci_write_reg(mcr, SH4_PCIMCR); + pci_write_reg(chan, mcr, SH4_PCIMCR); - pci_write_reg(0x0c000000, SH7751_PCICONF5); - pci_write_reg(0xd0000000, SH7751_PCICONF6); - pci_write_reg(0x0c000000, SH4_PCILAR0); - pci_write_reg(0x00000000, SH4_PCILAR1); + pci_write_reg(chan, 0x0c000000, SH7751_PCICONF5); + pci_write_reg(chan, 0xd0000000, SH7751_PCICONF6); + pci_write_reg(chan, 0x0c000000, SH4_PCILAR0); + pci_write_reg(chan, 0x00000000, SH4_PCILAR1); return 0; } diff --git a/arch/sh/drivers/pci/fixups-sdk7780.c b/arch/sh/drivers/pci/fixups-sdk7780.c index 2f8863099dd..250b0edd736 100644 --- a/arch/sh/drivers/pci/fixups-sdk7780.c +++ b/arch/sh/drivers/pci/fixups-sdk7780.c @@ -5,55 +5,48 @@ * * Copyright (C) 2003 Lineo uSolutions, Inc. * Copyright (C) 2004 - 2006 Paul Mundt + * Copyright (C) 2006 Nobuhiro Iwamatsu * * This file is subject to the terms and conditions of the GNU General Public * License. See the file "COPYING" in the main directory of this archive * for more details. */ #include <linux/pci.h> +#include <linux/io.h> #include "pci-sh4.h" -#include <asm/io.h> -int pci_fixup_pcic(void) +/* IDSEL [16][17][18][19][20][21][22][23][24][25][26][27][28][29][30][31] */ +static char sdk7780_irq_tab[4][16] __initdata = { + /* INTA */ + { 65, 68, 67, 68, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1 }, + /* INTB */ + { 66, 65, -1, 65, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1 }, + /* INTC */ + { 67, 66, -1, 66, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1 }, + /* INTD */ + { 68, 67, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1 }, +}; + +int __init pcibios_map_platform_irq(struct pci_dev *pdev, u8 slot, u8 pin) +{ + return sdk7780_irq_tab[pin-1][slot]; +} +int pci_fixup_pcic(struct pci_channel *chan) { - ctrl_outl(0x00000001, SH7780_PCI_VCR2); - /* Enable all interrupts, so we know what to fix */ - pci_write_reg(0x0000C3FF, SH7780_PCIIMR); - pci_write_reg(0x0000380F, SH7780_PCIAINTM); + pci_write_reg(chan, 0x0000C3FF, SH7780_PCIIMR); /* Set up standard PCI config registers */ - pci_write_reg(0xFB00, SH7780_PCISTATUS); - pci_write_reg(0x0047, SH7780_PCICMD); - pci_write_reg(0x00, SH7780_PCIPIF); - pci_write_reg(0x00, SH7780_PCISUB); - pci_write_reg(0x06, SH7780_PCIBCC); - pci_write_reg(0x1912, SH7780_PCISVID); - pci_write_reg(0x0001, SH7780_PCISID); - - pci_write_reg(0x08000000, SH7780_PCIMBAR0); /* PCI */ - pci_write_reg(0x08000000, SH7780_PCILAR0); /* SHwy */ - pci_write_reg(0x07F00001, SH7780_PCILSR); /* size 128M w/ MBAR */ - - pci_write_reg(0x00000000, SH7780_PCIMBAR1); - pci_write_reg(0x00000000, SH7780_PCILAR1); - pci_write_reg(0x00000000, SH7780_PCILSR1); - - pci_write_reg(0xAB000801, SH7780_PCIIBAR); - - /* - * Set the MBR so PCI address is one-to-one with window, - * meaning all calls go straight through... use ifdef to - * catch erroneous assumption. - */ - pci_write_reg(0xFD000000 , SH7780_PCIMBR0); - pci_write_reg(0x00FC0000 , SH7780_PCIMBMR0); /* 16M */ + pci_write_reg(chan, 0x08000000, SH7780_PCIMBAR0); /* PCI */ + pci_write_reg(chan, 0x08000000, SH4_PCILAR0); /* SHwy */ + pci_write_reg(chan, 0x07F00001, SH4_PCILSR0); /* size 128M w/ MBAR */ - /* Set IOBR for window containing area specified in pci.h */ - pci_write_reg(PCIBIOS_MIN_IO & ~(SH7780_PCI_IO_SIZE-1), SH7780_PCIIOBR); - pci_write_reg((SH7780_PCI_IO_SIZE-1) & (7 << 18), SH7780_PCIIOBMR); + pci_write_reg(chan, 0x00000000, SH7780_PCIMBAR1); + pci_write_reg(chan, 0x00000000, SH4_PCILAR1); + pci_write_reg(chan, 0x00000000, SH4_PCILSR1); - pci_write_reg(0xA5000C01, SH7780_PCICR); + pci_write_reg(chan, 0xAB000801, SH7780_PCIIBAR); + pci_write_reg(chan, 0xA5000C01, SH4_PCICR); return 0; } diff --git a/arch/sh/drivers/pci/fixups-se7751.c b/arch/sh/drivers/pci/fixups-se7751.c new file mode 100644 index 00000000000..475fa9f0fe2 --- /dev/null +++ b/arch/sh/drivers/pci/fixups-se7751.c @@ -0,0 +1,111 @@ +#include <linux/kernel.h> +#include <linux/types.h> +#include <linux/init.h> +#include <linux/delay.h> +#include <linux/pci.h> +#include <linux/io.h> +#include "pci-sh4.h" + +int __init pcibios_map_platform_irq(u8 slot, u8 pin) +{ + switch (slot) { + case 0: return 13; + case 1: return 13; /* AMD Ethernet controller */ + case 2: return -1; + case 3: return -1; + case 4: return -1; + default: + printk("PCI: Bad IRQ mapping request for slot %d\n", slot); + return -1; + } +} + +#define PCIMCR_MRSET_OFF 0xBFFFFFFF +#define PCIMCR_RFSH_OFF 0xFFFFFFFB + +/* + * Only long word accesses of the PCIC's internal local registers and the + * configuration registers from the CPU is supported. + */ +#define PCIC_WRITE(x,v) writel((v), PCI_REG(x)) +#define PCIC_READ(x) readl(PCI_REG(x)) + +/* + * Description: This function sets up and initializes the pcic, sets + * up the BARS, maps the DRAM into the address space etc, etc. + */ +int pci_fixup_pcic(struct pci_channel *chan) +{ + unsigned long bcr1, wcr1, wcr2, wcr3, mcr; + unsigned short bcr2; + + /* + * Initialize the slave bus controller on the pcic. The values used + * here should not be hardcoded, but they should be taken from the bsc + * on the processor, to make this function as generic as possible. + * (i.e. Another sbc may usr different SDRAM timing settings -- in order + * for the pcic to work, its settings need to be exactly the same.) + */ + bcr1 = (*(volatile unsigned long*)(SH7751_BCR1)); + bcr2 = (*(volatile unsigned short*)(SH7751_BCR2)); + wcr1 = (*(volatile unsigned long*)(SH7751_WCR1)); + wcr2 = (*(volatile unsigned long*)(SH7751_WCR2)); + wcr3 = (*(volatile unsigned long*)(SH7751_WCR3)); + mcr = (*(volatile unsigned long*)(SH7751_MCR)); + + bcr1 = bcr1 | 0x00080000; /* Enable Bit 19, BREQEN */ + (*(volatile unsigned long*)(SH7751_BCR1)) = bcr1; + + bcr1 = bcr1 | 0x40080000; /* Enable Bit 19 BREQEN, set PCIC to slave */ + PCIC_WRITE(SH7751_PCIBCR1, bcr1); /* PCIC BCR1 */ + PCIC_WRITE(SH7751_PCIBCR2, bcr2); /* PCIC BCR2 */ + PCIC_WRITE(SH7751_PCIWCR1, wcr1); /* PCIC WCR1 */ + PCIC_WRITE(SH7751_PCIWCR2, wcr2); /* PCIC WCR2 */ + PCIC_WRITE(SH7751_PCIWCR3, wcr3); /* PCIC WCR3 */ + mcr = (mcr & PCIMCR_MRSET_OFF) & PCIMCR_RFSH_OFF; + PCIC_WRITE(SH7751_PCIMCR, mcr); /* PCIC MCR */ + + + /* Enable all interrupts, so we know what to fix */ + PCIC_WRITE(SH7751_PCIINTM, 0x0000c3ff); + PCIC_WRITE(SH7751_PCIAINTM, 0x0000380f); + + /* Set up standard PCI config registers */ + PCIC_WRITE(SH7751_PCICONF1, 0xF39000C7); /* Bus Master, Mem & I/O access */ + PCIC_WRITE(SH7751_PCICONF2, 0x00000000); /* PCI Class code & Revision ID */ + PCIC_WRITE(SH7751_PCICONF4, 0xab000001); /* PCI I/O address (local regs) */ + PCIC_WRITE(SH7751_PCICONF5, 0x0c000000); /* PCI MEM address (local RAM) */ + PCIC_WRITE(SH7751_PCICONF6, 0xd0000000); /* PCI MEM address (unused) */ + PCIC_WRITE(SH7751_PCICONF11, 0x35051054); /* PCI Subsystem ID & Vendor ID */ + PCIC_WRITE(SH7751_PCILSR0, 0x03f00000); /* MEM (full 64M exposed) */ + PCIC_WRITE(SH7751_PCILSR1, 0x00000000); /* MEM (unused) */ + PCIC_WRITE(SH7751_PCILAR0, 0x0c000000); /* MEM (direct map from PCI) */ + PCIC_WRITE(SH7751_PCILAR1, 0x00000000); /* MEM (unused) */ + + /* Now turn it on... */ + PCIC_WRITE(SH7751_PCICR, 0xa5000001); + + /* + * Set PCIMBR and PCIIOBR here, assuming a single window + * (16M MEM, 256K IO) is enough. If a larger space is + * needed, the readx/writex and inx/outx functions will + * have to do more (e.g. setting registers for each call). + */ + + /* + * Set the MBR so PCI address is one-to-one with window, + * meaning all calls go straight through... use BUG_ON to + * catch erroneous assumption. + */ + BUG_ON(chan->mem_resource->start != SH7751_PCI_MEMORY_BASE); + + PCIC_WRITE(SH7751_PCIMBR, chan->mem_resource->start); + + /* Set IOBR for window containing area specified in pci.h */ + PCIC_WRITE(SH7751_PCIIOBR, (chan->io_resource->start & SH7751_PCIIOBR_MASK)); + + /* All done, may as well say so... */ + printk("SH7751 PCI: Finished initialization of the PCI controller\n"); + + return 1; +} diff --git a/arch/sh/drivers/pci/fixups-se7780.c b/arch/sh/drivers/pci/fixups-se7780.c deleted file mode 100644 index 880cea1c0d8..00000000000 --- a/arch/sh/drivers/pci/fixups-se7780.c +++ /dev/null @@ -1,60 +0,0 @@ -/* - * arch/sh/drivers/pci/fixups-se7780.c - * - * HITACHI UL Solution Engine 7780 PCI fixups - * - * Copyright (C) 2003 Lineo uSolutions, Inc. - * Copyright (C) 2004 - 2006 Paul Mundt - * Copyright (C) 2006 Nobuhiro Iwamatsu - * - * This file is subject to the terms and conditions of the GNU General Public - * License. See the file "COPYING" in the main directory of this archive - * for more details. - */ -#include <linux/pci.h> -#include "pci-sh4.h" -#include <asm/io.h> - -int pci_fixup_pcic(void) -{ - ctrl_outl(0x00000001, SH7780_PCI_VCR2); - - /* Enable all interrupts, so we know what to fix */ - pci_write_reg(0x0000C3FF, SH7780_PCIIMR); - pci_write_reg(0x0000380F, SH7780_PCIAINTM); - - /* Set up standard PCI config registers */ - ctrl_outw(0xFB00, PCI_REG(SH7780_PCISTATUS)); - ctrl_outw(0x0047, PCI_REG(SH7780_PCICMD)); - ctrl_outb( 0x00, PCI_REG(SH7780_PCIPIF)); - ctrl_outb( 0x00, PCI_REG(SH7780_PCISUB)); - ctrl_outb( 0x06, PCI_REG(SH7780_PCIBCC)); - ctrl_outw(0x1912, PCI_REG(SH7780_PCISVID)); - ctrl_outw(0x0001, PCI_REG(SH7780_PCISID)); - - pci_write_reg(0x08000000, SH7780_PCIMBAR0); /* PCI */ - pci_write_reg(0x08000000, SH7780_PCILAR0); /* SHwy */ - pci_write_reg(0x07F00001, SH7780_PCILSR); /* size 128M w/ MBAR */ - - pci_write_reg(0x00000000, SH7780_PCIMBAR1); - pci_write_reg(0x00000000, SH7780_PCILAR1); - pci_write_reg(0x00000000, SH7780_PCILSR1); - - pci_write_reg(0xAB000801, SH7780_PCIIBAR); - - /* - * Set the MBR so PCI address is one-to-one with window, - * meaning all calls go straight through... use ifdef to - * catch erroneous assumption. - */ - pci_write_reg(0xFD000000 , SH7780_PCIMBR0); - pci_write_reg(0x00FC0000 , SH7780_PCIMBMR0); /* 16M */ - - /* Set IOBR for window containing area specified in pci.h */ - pci_write_reg(PCIBIOS_MIN_IO & ~(SH7780_PCI_IO_SIZE-1), SH7780_PCIIOBR); - pci_write_reg((SH7780_PCI_IO_SIZE-1) & (7 << 18), SH7780_PCIIOBMR); - - pci_write_reg(0xA5000C01, SH7780_PCICR); - - return 0; -} diff --git a/arch/sh/drivers/pci/fixups-sh7785lcr.c b/arch/sh/drivers/pci/fixups-sh7785lcr.c deleted file mode 100644 index 4949e601387..00000000000 --- a/arch/sh/drivers/pci/fixups-sh7785lcr.c +++ /dev/null @@ -1,46 +0,0 @@ -/* - * arch/sh/drivers/pci/fixups-sh7785lcr.c - * - * R0P7785LC0011RL PCI fixups - * Copyright (C) 2008 Yoshihiro Shimoda - * - * Based on arch/sh/drivers/pci/fixups-r7780rp.c - * Copyright (C) 2003 Lineo uSolutions, Inc. - * Copyright (C) 2004 - 2006 Paul Mundt - * - * This file is subject to the terms and conditions of the GNU General Public - * License. See the file "COPYING" in the main directory of this archive - * for more details. - */ -#include <linux/pci.h> -#include "pci-sh4.h" - -int pci_fixup_pcic(void) -{ - pci_write_reg(0x000043ff, SH4_PCIINTM); - pci_write_reg(0x0000380f, SH4_PCIAINTM); - - pci_write_reg(0xfbb00047, SH7780_PCICMD); - pci_write_reg(0x00000000, SH7780_PCIIBAR); - - pci_write_reg(0x00011912, SH7780_PCISVID); - pci_write_reg(0x08000000, SH7780_PCICSCR0); - pci_write_reg(0x0000001b, SH7780_PCICSAR0); - pci_write_reg(0xfd000000, SH7780_PCICSCR1); - pci_write_reg(0x0000000f, SH7780_PCICSAR1); - - pci_write_reg(0xfd000000, SH7780_PCIMBR0); - pci_write_reg(0x00fc0000, SH7780_PCIMBMR0); - -#ifdef CONFIG_32BIT - pci_write_reg(0xc0000000, SH7780_PCIMBR2); - pci_write_reg(0x20000000 - SH7780_PCI_IO_SIZE, SH7780_PCIMBMR2); -#endif - - /* Set IOBR for windows containing area specified in pci.h */ - pci_write_reg((PCIBIOS_MIN_IO & ~(SH7780_PCI_IO_SIZE - 1)), - SH7780_PCIIOBR); - pci_write_reg(((SH7780_PCI_IO_SIZE - 1) & (7 << 18)), SH7780_PCIIOBMR); - - return 0; -} diff --git a/arch/sh/drivers/pci/fixups-snapgear.c b/arch/sh/drivers/pci/fixups-snapgear.c new file mode 100644 index 00000000000..5a39ecc1adb --- /dev/null +++ b/arch/sh/drivers/pci/fixups-snapgear.c @@ -0,0 +1,38 @@ +/* + * arch/sh/drivers/pci/ops-snapgear.c + * + * Author: David McCullough <davidm@snapgear.com> + * + * Ported to new API by Paul Mundt <lethal@linux-sh.org> + * + * Highly leveraged from pci-bigsur.c, written by Dustin McIntire. + * + * May be copied or modified under the terms of the GNU General Public + * License. See linux/COPYING for more information. + * + * PCI initialization for the SnapGear boards + */ +#include <linux/kernel.h> +#include <linux/types.h> +#include <linux/init.h> +#include <linux/pci.h> +#include "pci-sh4.h" + +int __init pcibios_map_platform_irq(struct pci_dev *pdev, u8 slot, u8 pin) +{ + int irq = -1; + + switch (slot) { + case 8: /* the PCI bridge */ break; + case 11: irq = 8; break; /* USB */ + case 12: irq = 11; break; /* PCMCIA */ + case 13: irq = 5; break; /* eth0 */ + case 14: irq = 8; break; /* eth1 */ + case 15: irq = 11; break; /* safenet (unused) */ + } + + printk("PCI: Mapping SnapGear IRQ for slot %d, pin %c to irq %d\n", + slot, pin - 1 + 'A', irq); + + return irq; +} diff --git a/arch/sh/drivers/pci/ops-titan.c b/arch/sh/drivers/pci/fixups-titan.c index a8f7801a34a..3a79fa8254a 100644 --- a/arch/sh/drivers/pci/ops-titan.c +++ b/arch/sh/drivers/pci/fixups-titan.c @@ -36,42 +36,3 @@ int __init pcibios_map_platform_irq(struct pci_dev *pdev, u8 slot, u8 pin) return irq; } - -static struct resource sh7751_io_resource = { - .name = "SH7751_IO", - .start = SH7751_PCI_IO_BASE, - .end = SH7751_PCI_IO_BASE + SH7751_PCI_IO_SIZE - 1, - .flags = IORESOURCE_IO -}; - -static struct resource sh7751_mem_resource = { - .name = "SH7751_mem", - .start = SH7751_PCI_MEMORY_BASE, - .end = SH7751_PCI_MEMORY_BASE + SH7751_PCI_MEM_SIZE - 1, - .flags = IORESOURCE_MEM -}; - -struct pci_channel board_pci_channels[] = { - { &sh4_pci_ops, &sh7751_io_resource, &sh7751_mem_resource, 0, 0xff }, - { NULL, NULL, NULL, 0, 0 }, -}; -EXPORT_SYMBOL(board_pci_channels); - -static struct sh4_pci_address_map sh7751_pci_map = { - .window0 = { - .base = SH7751_CS2_BASE_ADDR, - .size = SH7751_MEM_REGION_SIZE*2, /* cs2 and cs3 */ - }, - - .window1 = { - .base = SH7751_CS2_BASE_ADDR, - .size = SH7751_MEM_REGION_SIZE*2, - }, - - .flags = SH4_PCIC_NO_RESET, -}; - -int __init pcibios_init_platform(void) -{ - return sh7751_pcic_init(&sh7751_pci_map); -} diff --git a/arch/sh/drivers/pci/ops-dreamcast.c b/arch/sh/drivers/pci/ops-dreamcast.c index f5d2a2aa6f3..e83d0d3aabe 100644 --- a/arch/sh/drivers/pci/ops-dreamcast.c +++ b/arch/sh/drivers/pci/ops-dreamcast.c @@ -1,15 +1,9 @@ /* - * arch/sh/drivers/pci/ops-dreamcast.c - * * PCI operations for the Sega Dreamcast * * Copyright (C) 2001, 2002 M. R. Brown * Copyright (C) 2002, 2003 Paul Mundt * - * This file originally bore the message (with enclosed-$): - * Id: pci.c,v 1.3 2003/05/04 19:29:46 lethal Exp - * Dreamcast PCI: Supports SEGA Broadband Adaptor only. - * * This file is subject to the terms and conditions of the GNU General Public * License. See the file "COPYING" in the main directory of this archive * for more details. @@ -23,34 +17,10 @@ #include <linux/irq.h> #include <linux/pci.h> #include <linux/module.h> - -#include <asm/io.h> -#include <asm/irq.h> +#include <linux/io.h> +#include <linux/irq.h> #include <mach/pci.h> -static struct resource gapspci_io_resource = { - .name = "GAPSPCI IO", - .start = GAPSPCI_BBA_CONFIG, - .end = GAPSPCI_BBA_CONFIG + GAPSPCI_BBA_CONFIG_SIZE - 1, - .flags = IORESOURCE_IO, -}; - -static struct resource gapspci_mem_resource = { - .name = "GAPSPCI mem", - .start = GAPSPCI_DMA_BASE, - .end = GAPSPCI_DMA_BASE + GAPSPCI_DMA_SIZE - 1, - .flags = IORESOURCE_MEM, -}; - -static struct pci_ops gapspci_pci_ops; - -struct pci_channel board_pci_channels[] = { - { &gapspci_pci_ops, &gapspci_io_resource, - &gapspci_mem_resource, 0, 1 }, - { 0, } -}; -EXPORT_SYMBOL(board_pci_channels); - /* * The !gapspci_config_access case really shouldn't happen, ever, unless * someone implicitly messes around with the last devfn value.. otherwise we @@ -85,10 +55,10 @@ static int gapspci_read(struct pci_bus *bus, unsigned int devfn, int where, int return PCIBIOS_DEVICE_NOT_FOUND; switch (size) { - case 1: *val = inb(GAPSPCI_BBA_CONFIG+where); break; - case 2: *val = inw(GAPSPCI_BBA_CONFIG+where); break; - case 4: *val = inl(GAPSPCI_BBA_CONFIG+where); break; - } + case 1: *val = inb(GAPSPCI_BBA_CONFIG+where); break; + case 2: *val = inw(GAPSPCI_BBA_CONFIG+where); break; + case 4: *val = inl(GAPSPCI_BBA_CONFIG+where); break; + } return PCIBIOS_SUCCESSFUL; } @@ -99,72 +69,15 @@ static int gapspci_write(struct pci_bus *bus, unsigned int devfn, int where, int return PCIBIOS_DEVICE_NOT_FOUND; switch (size) { - case 1: outb(( u8)val, GAPSPCI_BBA_CONFIG+where); break; - case 2: outw((u16)val, GAPSPCI_BBA_CONFIG+where); break; - case 4: outl((u32)val, GAPSPCI_BBA_CONFIG+where); break; + case 1: outb(( u8)val, GAPSPCI_BBA_CONFIG+where); break; + case 2: outw((u16)val, GAPSPCI_BBA_CONFIG+where); break; + case 4: outl((u32)val, GAPSPCI_BBA_CONFIG+where); break; } return PCIBIOS_SUCCESSFUL; } -static struct pci_ops gapspci_pci_ops = { +struct pci_ops gapspci_pci_ops = { .read = gapspci_read, .write = gapspci_write, }; - -/* - * gapspci init - */ - -int __init gapspci_init(void) -{ - char idbuf[16]; - int i; - - /* - * FIXME: All of this wants documenting to some degree, - * even some basic register definitions would be nice. - * - * I haven't seen anything this ugly since.. maple. - */ - - for (i=0; i<16; i++) - idbuf[i] = inb(GAPSPCI_REGS+i); - - if (strncmp(idbuf, "GAPSPCI_BRIDGE_2", 16)) - return -ENODEV; - - outl(0x5a14a501, GAPSPCI_REGS+0x18); - - for (i=0; i<1000000; i++) - ; - - if (inl(GAPSPCI_REGS+0x18) != 1) - return -EINVAL; - - outl(0x01000000, GAPSPCI_REGS+0x20); - outl(0x01000000, GAPSPCI_REGS+0x24); - - outl(GAPSPCI_DMA_BASE, GAPSPCI_REGS+0x28); - outl(GAPSPCI_DMA_BASE+GAPSPCI_DMA_SIZE, GAPSPCI_REGS+0x2c); - - outl(1, GAPSPCI_REGS+0x14); - outl(1, GAPSPCI_REGS+0x34); - - /* Setting Broadband Adapter */ - outw(0xf900, GAPSPCI_BBA_CONFIG+0x06); - outl(0x00000000, GAPSPCI_BBA_CONFIG+0x30); - outb(0x00, GAPSPCI_BBA_CONFIG+0x3c); - outb(0xf0, GAPSPCI_BBA_CONFIG+0x0d); - outw(0x0006, GAPSPCI_BBA_CONFIG+0x04); - outl(0x00002001, GAPSPCI_BBA_CONFIG+0x10); - outl(0x01000000, GAPSPCI_BBA_CONFIG+0x14); - - return 0; -} - -/* Haven't done anything here as yet */ -char * __devinit pcibios_setup(char *str) -{ - return str; -} diff --git a/arch/sh/drivers/pci/ops-lboxre2.c b/arch/sh/drivers/pci/ops-lboxre2.c deleted file mode 100644 index 86c0b6fb737..00000000000 --- a/arch/sh/drivers/pci/ops-lboxre2.c +++ /dev/null @@ -1,63 +0,0 @@ -/* - * linux/arch/sh/drivers/pci/ops-lboxre2.c - * - * Copyright (C) 2007 Nobuhiro Iwamatsu - * - * PCI initialization for the NTT COMWARE L-BOX RE2 - */ -#include <linux/kernel.h> -#include <linux/types.h> -#include <linux/init.h> -#include <linux/pci.h> -#include <linux/io.h> -#include <mach/lboxre2.h> -#include "pci-sh4.h" - -static char lboxre2_irq_tab[] __initdata = { - IRQ_ETH0, IRQ_ETH1, IRQ_INTA, IRQ_INTD, -}; - -int __init pcibios_map_platform_irq(struct pci_dev *pdev, u8 slot, u8 pin) -{ - return lboxre2_irq_tab[slot]; -} - -static struct resource sh7751_io_resource = { - .name = "SH7751_IO", - .start = SH7751_PCI_IO_BASE , - .end = SH7751_PCI_IO_BASE + SH7751_PCI_IO_SIZE - 1, - .flags = IORESOURCE_IO -}; - -static struct resource sh7751_mem_resource = { - .name = "SH7751_mem", - .start = SH7751_PCI_MEMORY_BASE, - .end = SH7751_PCI_MEMORY_BASE + SH7751_PCI_MEM_SIZE - 1, - .flags = IORESOURCE_MEM -}; - -extern struct pci_ops sh7751_pci_ops; - -struct pci_channel board_pci_channels[] = { - { &sh4_pci_ops, &sh7751_io_resource, &sh7751_mem_resource, 0, 0xff }, - { NULL, NULL, NULL, 0, 0 }, -}; - -EXPORT_SYMBOL(board_pci_channels); - -static struct sh4_pci_address_map sh7751_pci_map = { - .window0 = { - .base = SH7751_CS3_BASE_ADDR, - .size = 0x04000000, - }, - .window1 = { - .base = 0x00000000, /* Unused */ - .size = 0x00000000, /* Unused */ - }, - .flags = SH4_PCIC_NO_RESET, -}; - -int __init pcibios_init_platform(void) -{ - return sh7751_pcic_init(&sh7751_pci_map); -} diff --git a/arch/sh/drivers/pci/ops-r7780rp.c b/arch/sh/drivers/pci/ops-r7780rp.c deleted file mode 100644 index 8555238e63e..00000000000 --- a/arch/sh/drivers/pci/ops-r7780rp.c +++ /dev/null @@ -1,68 +0,0 @@ -/* - * Author: Ian DaSilva (idasilva@mvista.com) - * - * Highly leveraged from pci-bigsur.c, written by Dustin McIntire. - * - * May be copied or modified under the terms of the GNU General Public - * License. See linux/COPYING for more information. - * - * PCI initialization for the Renesas SH7780 Highlander R7780RP-1 board - */ -#include <linux/kernel.h> -#include <linux/types.h> -#include <linux/init.h> -#include <linux/delay.h> -#include <linux/pci.h> -#include <mach/highlander.h> -#include <asm/io.h> -#include "pci-sh4.h" - -static char irq_tab[] __initdata = { - 65, 66, 67, 68, -}; - -int __init pcibios_map_platform_irq(struct pci_dev *pdev, u8 slot, u8 pin) -{ - return irq_tab[slot]; -} - -static struct resource sh7780_io_resource = { - .name = "SH7780_IO", - .start = SH7780_PCI_IO_BASE, - .end = SH7780_PCI_IO_BASE + SH7780_PCI_IO_SIZE - 1, - .flags = IORESOURCE_IO -}; - -static struct resource sh7780_mem_resource = { - .name = "SH7780_mem", - .start = SH7780_PCI_MEMORY_BASE, - .end = SH7780_PCI_MEMORY_BASE + SH7780_PCI_MEM_SIZE - 1, - .flags = IORESOURCE_MEM -}; - -extern struct pci_ops sh7780_pci_ops; - -struct pci_channel board_pci_channels[] = { - { &sh4_pci_ops, &sh7780_io_resource, &sh7780_mem_resource, 0, 0xff }, - { NULL, NULL, NULL, 0, 0 }, -}; -EXPORT_SYMBOL(board_pci_channels); - -static struct sh4_pci_address_map sh7780_pci_map = { - .window0 = { - .base = SH7780_CS2_BASE_ADDR, - .size = 0x04000000, - }, - - .window1 = { - .base = SH7780_CS3_BASE_ADDR, - .size = 0x04000000, - }, - - .flags = SH4_PCIC_NO_RESET, -}; - -int __init pcibios_init_platform(void) -{ - return sh7780_pcic_init(&sh7780_pci_map); -} diff --git a/arch/sh/drivers/pci/ops-rts7751r2d.c b/arch/sh/drivers/pci/ops-rts7751r2d.c deleted file mode 100644 index d6ca74b25d5..00000000000 --- a/arch/sh/drivers/pci/ops-rts7751r2d.c +++ /dev/null @@ -1,74 +0,0 @@ -/* - * linux/arch/sh/drivers/pci/ops-rts7751r2d.c - * - * Author: Ian DaSilva (idasilva@mvista.com) - * - * Highly leveraged from pci-bigsur.c, written by Dustin McIntire. - * - * May be copied or modified under the terms of the GNU General Public - * License. See linux/COPYING for more information. - * - * PCI initialization for the Renesas SH7751R RTS7751R2D board - */ -#include <linux/kernel.h> -#include <linux/types.h> -#include <linux/init.h> -#include <linux/pci.h> -#include <linux/io.h> -#include <mach/r2d.h> -#include "pci-sh4.h" - -static u8 rts7751r2d_irq_tab[] __initdata = { - IRQ_PCI_INTA, - IRQ_PCI_INTB, - IRQ_PCI_INTC, - IRQ_PCI_INTD, -}; - -int __init pcibios_map_platform_irq(struct pci_dev *pdev, u8 slot, u8 pin) -{ - return rts7751r2d_irq_tab[slot]; -} - -static struct resource sh7751_io_resource = { - .name = "SH7751_IO", - .start = 0x4000, - .end = SH7751_PCI_IO_SIZE - 1, - .flags = IORESOURCE_IO -}; - -static struct resource sh7751_mem_resource = { - .name = "SH7751_mem", - .start = SH7751_PCI_MEMORY_BASE, - .end = SH7751_PCI_MEMORY_BASE + SH7751_PCI_MEM_SIZE - 1, - .flags = IORESOURCE_MEM -}; - -extern struct pci_ops sh7751_pci_ops; - -struct pci_channel board_pci_channels[] = { - { &sh4_pci_ops, &sh7751_io_resource, &sh7751_mem_resource, 0, 0xff }, - { NULL, NULL, NULL, 0, 0 }, -}; -EXPORT_SYMBOL(board_pci_channels); - -static struct sh4_pci_address_map sh7751_pci_map = { - .window0 = { - .base = SH7751_CS3_BASE_ADDR, - .size = 0x04000000, - }, - - .window1 = { - .base = 0x00000000, /* Unused */ - .size = 0x00000000, /* Unused */ - }, - - .flags = SH4_PCIC_NO_RESET, -}; - -int __init pcibios_init_platform(void) -{ - __set_io_port_base(SH7751_PCI_IO_BASE); - return sh7751_pcic_init(&sh7751_pci_map); -} - diff --git a/arch/sh/drivers/pci/ops-sdk7780.c b/arch/sh/drivers/pci/ops-sdk7780.c deleted file mode 100644 index 4dcc64184b2..00000000000 --- a/arch/sh/drivers/pci/ops-sdk7780.c +++ /dev/null @@ -1,73 +0,0 @@ -/* - * linux/arch/sh/drivers/pci/ops-sdk7780.c - * - * Copyright (C) 2006 Nobuhiro Iwamatsu - * - * PCI initialization for the SDK7780SE03 - * - * May be copied or modified under the terms of the GNU General Public - * License. See linux/COPYING for more information. - */ -#include <linux/kernel.h> -#include <linux/types.h> -#include <linux/init.h> -#include <linux/delay.h> -#include <linux/pci.h> -#include <mach/sdk7780.h> -#include <asm/io.h> -#include "pci-sh4.h" - -/* IDSEL [16][17][18][19][20][21][22][23][24][25][26][27][28][29][30][31] */ -static char sdk7780_irq_tab[4][16] __initdata = { - /* INTA */ - { 65, 68, 67, 68, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1 }, - /* INTB */ - { 66, 65, -1, 65, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1 }, - /* INTC */ - { 67, 66, -1, 66, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1 }, - /* INTD */ - { 68, 67, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1 }, -}; - -int __init pcibios_map_platform_irq(struct pci_dev *pdev, u8 slot, u8 pin) -{ - return sdk7780_irq_tab[pin-1][slot]; -} - -static struct resource sdk7780_io_resource = { - .name = "SH7780_IO", - .start = SH7780_PCI_IO_BASE, - .end = SH7780_PCI_IO_BASE + SH7780_PCI_IO_SIZE - 1, - .flags = IORESOURCE_IO -}; - -static struct resource sdk7780_mem_resource = { - .name = "SH7780_mem", - .start = SH7780_PCI_MEMORY_BASE, - .end = SH7780_PCI_MEMORY_BASE + SH7780_PCI_MEM_SIZE - 1, - .flags = IORESOURCE_MEM -}; - -struct pci_channel board_pci_channels[] = { - { &sh4_pci_ops, &sdk7780_io_resource, &sdk7780_mem_resource, 0, 0xff }, - { NULL, NULL, NULL, 0, 0 }, -}; -EXPORT_SYMBOL(board_pci_channels); - -static struct sh4_pci_address_map sdk7780_pci_map = { - .window0 = { - .base = SH7780_CS2_BASE_ADDR, - .size = 0x04000000, - }, - .window1 = { - .base = SH7780_CS3_BASE_ADDR, - .size = 0x04000000, - }, - .flags = SH4_PCIC_NO_RESET, -}; - -int __init pcibios_init_platform(void) -{ - printk(KERN_INFO "SH7780 PCI: Finished initializing PCI controller\n"); - return sh7780_pcic_init(&sdk7780_pci_map); -} diff --git a/arch/sh/drivers/pci/ops-se7780.c b/arch/sh/drivers/pci/ops-se7780.c deleted file mode 100644 index 3145c62484d..00000000000 --- a/arch/sh/drivers/pci/ops-se7780.c +++ /dev/null @@ -1,96 +0,0 @@ -/* - * linux/arch/sh/drivers/pci/ops-se7780.c - * - * Copyright (C) 2006 Nobuhiro Iwamatsu - * - * PCI initialization for the Hitachi UL Solution Engine 7780SE03 - * - * May be copied or modified under the terms of the GNU General Public - * License. See linux/COPYING for more information. - */ -#include <linux/kernel.h> -#include <linux/types.h> -#include <linux/init.h> -#include <linux/delay.h> -#include <linux/pci.h> -#include <mach-se/mach/se7780.h> -#include <asm/io.h> -#include "pci-sh4.h" - -/* - * IDSEL = AD16 PCI slot - * IDSEL = AD17 PCI slot - * IDSEL = AD18 Serial ATA Controller (Silicon Image SiL3512A) - * IDSEL = AD19 USB Host Controller (NEC uPD7210100A) - */ - -/* IDSEL [16][17][18][19][20][21][22][23][24][25][26][27][28][29][30][31] */ -static char se7780_irq_tab[4][16] __initdata = { - /* INTA */ - { 65, 68, 67, 68, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1 }, - /* INTB */ - { 66, 65, -1, 65, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1 }, - /* INTC */ - { 67, 66, -1, 66, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1 }, - /* INTD */ - { 68, 67, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1 }, -}; - -int __init pcibios_map_platform_irq(struct pci_dev *pdev, u8 slot, u8 pin) -{ - return se7780_irq_tab[pin-1][slot]; -} - -static struct resource se7780_io_resource = { - .name = "SH7780_IO", - .start = SH7780_PCI_IO_BASE, - .end = SH7780_PCI_IO_BASE + SH7780_PCI_IO_SIZE - 1, - .flags = IORESOURCE_IO -}; - -static struct resource se7780_mem_resource = { - .name = "SH7780_mem", - .start = SH7780_PCI_MEMORY_BASE, - .end = SH7780_PCI_MEMORY_BASE + SH7780_PCI_MEM_SIZE - 1, - .flags = IORESOURCE_MEM -}; - -extern struct pci_ops se7780_pci_ops; - -struct pci_channel board_pci_channels[] = { - { &sh4_pci_ops, &se7780_io_resource, &se7780_mem_resource, 0, 0xff }, - { NULL, NULL, NULL, 0, 0 }, -}; -EXPORT_SYMBOL(board_pci_channels); - -static struct sh4_pci_address_map se7780_pci_map = { - .window0 = { - .base = SH7780_CS2_BASE_ADDR, - .size = 0x04000000, - }, - .flags = SH4_PCIC_NO_RESET, -}; - -int __init pcibios_init_platform(void) -{ - printk("SH7780 PCI: Finished initialization of the PCI controller\n"); - - /* - * FPGA PCISEL register initialize - * - * CPU || SLOT1 | SLOT2 | S-ATA | USB - * ------------------------------------- - * INTA || INTA | INTD | -- | INTB - * ------------------------------------- - * INTB || INTB | INTA | -- | INTC - * ------------------------------------- - * INTC || INTC | INTB | INTA | -- - * ------------------------------------- - * INTD || INTD | INTC | -- | INTA - * ------------------------------------- - */ - ctrl_outw(0x0013, FPGA_PCI_INTSEL1); - ctrl_outw(0xE402, FPGA_PCI_INTSEL2); - - return sh7780_pcic_init(&se7780_pci_map); -} diff --git a/arch/sh/drivers/pci/ops-sh03.c b/arch/sh/drivers/pci/ops-sh03.c deleted file mode 100644 index e1703ff5a4d..00000000000 --- a/arch/sh/drivers/pci/ops-sh03.c +++ /dev/null @@ -1,45 +0,0 @@ -/* - * linux/arch/sh/drivers/pci/ops-sh03.c - * - * PCI initialization for the Interface CTP/PCI-SH03 board - */ - -#include <linux/kernel.h> -#include <linux/types.h> -#include <linux/init.h> -#include <linux/delay.h> -#include <linux/pci.h> -#include <asm/io.h> -#include "pci-sh7751.h" - -/* - * Description: This function sets up and initializes the pcic, sets - * up the BARS, maps the DRAM into the address space etc, etc. - */ -int __init pcibios_init_platform(void) -{ - __set_io_port_base(SH7751_PCI_IO_BASE); - return 1; -} - -static struct resource sh7751_io_resource = { - .name = "SH03 IO", - .start = SH7751_PCI_IO_BASE, - .end = SH7751_PCI_IO_BASE + SH7751_PCI_IO_SIZE - 1, - .flags = IORESOURCE_IO -}; - -static struct resource sh7751_mem_resource = { - .name = "SH03 mem", - .start = SH7751_PCI_MEMORY_BASE, - .end = SH7751_PCI_MEMORY_BASE + SH7751_PCI_MEM_SIZE - 1, - .flags = IORESOURCE_MEM -}; - -extern struct pci_ops sh4_pci_ops; - -struct pci_channel board_pci_channels[] = { - { &sh4_pci_ops, &sh7751_io_resource, &sh7751_mem_resource, 0, 0xff }, - { NULL, NULL, NULL, 0, 0 }, -}; - diff --git a/arch/sh/drivers/pci/ops-sh4.c b/arch/sh/drivers/pci/ops-sh4.c index 710a3b0306e..78bebebdc99 100644 --- a/arch/sh/drivers/pci/ops-sh4.c +++ b/arch/sh/drivers/pci/ops-sh4.c @@ -1,22 +1,22 @@ /* * Generic SH-4 / SH-4A PCIC operations (SH7751, SH7780). * - * Copyright (C) 2002 - 2006 Paul Mundt + * Copyright (C) 2002 - 2009 Paul Mundt * * This file is subject to the terms and conditions of the GNU General Public * License v2. See the file "COPYING" in the main directory of this archive * for more details. */ #include <linux/pci.h> +#include <linux/io.h> #include <asm/addrspace.h> -#include <asm/io.h> #include "pci-sh4.h" /* * Direct access to PCI hardware... */ #define CONFIG_CMD(bus, devfn, where) \ - P1SEGADDR((bus->number << 16) | (devfn << 8) | (where & ~3)) + (P1SEG | (bus->number << 16) | (devfn << 8) | (where & ~3)) static DEFINE_SPINLOCK(sh4_pci_lock); @@ -26,6 +26,7 @@ static DEFINE_SPINLOCK(sh4_pci_lock); static int sh4_pci_read(struct pci_bus *bus, unsigned int devfn, int where, int size, u32 *val) { + struct pci_channel *chan = bus->sysdata; unsigned long flags; u32 data; @@ -34,8 +35,8 @@ static int sh4_pci_read(struct pci_bus *bus, unsigned int devfn, * so we must do byte alignment by hand */ spin_lock_irqsave(&sh4_pci_lock, flags); - pci_write_reg(CONFIG_CMD(bus, devfn, where), SH4_PCIPAR); - data = pci_read_reg(SH4_PCIPDR); + pci_write_reg(chan, CONFIG_CMD(bus, devfn, where), SH4_PCIPAR); + data = pci_read_reg(chan, SH4_PCIPDR); spin_unlock_irqrestore(&sh4_pci_lock, flags); switch (size) { @@ -63,13 +64,14 @@ static int sh4_pci_read(struct pci_bus *bus, unsigned int devfn, static int sh4_pci_write(struct pci_bus *bus, unsigned int devfn, int where, int size, u32 val) { + struct pci_channel *chan = bus->sysdata; unsigned long flags; int shift; u32 data; spin_lock_irqsave(&sh4_pci_lock, flags); - pci_write_reg(CONFIG_CMD(bus, devfn, where), SH4_PCIPAR); - data = pci_read_reg(SH4_PCIPDR); + pci_write_reg(chan, CONFIG_CMD(bus, devfn, where), SH4_PCIPAR); + data = pci_read_reg(chan, SH4_PCIPDR); spin_unlock_irqrestore(&sh4_pci_lock, flags); switch (size) { @@ -90,7 +92,7 @@ static int sh4_pci_write(struct pci_bus *bus, unsigned int devfn, return PCIBIOS_FUNC_NOT_SUPPORTED; } - pci_write_reg(data, SH4_PCIPDR); + pci_write_reg(chan, data, SH4_PCIPDR); return PCIBIOS_SUCCESSFUL; } @@ -104,66 +106,31 @@ struct pci_ops sh4_pci_ops = { * Not really related to pci_ops, but it's common and not worth shoving * somewhere else for now.. */ -static unsigned int pci_probe = PCI_PROBE_CONF1; - -int __init sh4_pci_check_direct(void) +int __init sh4_pci_check_direct(struct pci_channel *chan) { /* * Check if configuration works. */ - if (pci_probe & PCI_PROBE_CONF1) { - unsigned int tmp = pci_read_reg(SH4_PCIPAR); - - pci_write_reg(P1SEG, SH4_PCIPAR); + unsigned int tmp = pci_read_reg(chan, SH4_PCIPAR); - if (pci_read_reg(SH4_PCIPAR) == P1SEG) { - pci_write_reg(tmp, SH4_PCIPAR); - printk(KERN_INFO "PCI: Using configuration type 1\n"); - request_region(PCI_REG(SH4_PCIPAR), 8, "PCI conf1"); + pci_write_reg(chan, P1SEG, SH4_PCIPAR); - return 0; - } - - pci_write_reg(tmp, SH4_PCIPAR); + if (pci_read_reg(chan, SH4_PCIPAR) == P1SEG) { + pci_write_reg(chan, tmp, SH4_PCIPAR); + printk(KERN_INFO "PCI: Using configuration type 1\n"); + request_region(chan->reg_base + SH4_PCIPAR, 8, + "PCI conf1"); + return 0; } - pr_debug("PCI: pci_check_direct failed\n"); - return -EINVAL; -} + pci_write_reg(chan, tmp, SH4_PCIPAR); -/* Handle generic fixups */ -static void __init pci_fixup_ide_bases(struct pci_dev *d) -{ - int i; + printk(KERN_ERR "PCI: %s failed\n", __func__); - /* - * PCI IDE controllers use non-standard I/O port decoding, respect it. - */ - if ((d->class >> 8) != PCI_CLASS_STORAGE_IDE) - return; - pr_debug("PCI: IDE base address fixup for %s\n", pci_name(d)); - for(i = 0; i < 4; i++) { - struct resource *r = &d->resource[i]; - - if ((r->start & ~0x80) == 0x374) { - r->start |= 2; - r->end = r->start; - } - } -} -DECLARE_PCI_FIXUP_HEADER(PCI_ANY_ID, PCI_ANY_ID, pci_fixup_ide_bases); - -char * __devinit pcibios_setup(char *str) -{ - if (!strcmp(str, "off")) { - pci_probe = 0; - return NULL; - } - - return str; + return -EINVAL; } -int __attribute__((weak)) pci_fixup_pcic(void) +int __attribute__((weak)) pci_fixup_pcic(struct pci_channel *chan) { /* Nothing to do. */ return 0; diff --git a/arch/sh/drivers/pci/ops-sh5.c b/arch/sh/drivers/pci/ops-sh5.c index 729e38a6fe0..4ce95a001b8 100644 --- a/arch/sh/drivers/pci/ops-sh5.c +++ b/arch/sh/drivers/pci/ops-sh5.c @@ -22,31 +22,6 @@ #include <asm/io.h> #include "pci-sh5.h" -static void __init pci_fixup_ide_bases(struct pci_dev *d) -{ - int i; - - /* - * PCI IDE controllers use non-standard I/O port decoding, respect it. - */ - if ((d->class >> 8) != PCI_CLASS_STORAGE_IDE) - return; - printk("PCI: IDE base address fixup for %s\n", pci_name(d)); - for(i=0; i<4; i++) { - struct resource *r = &d->resource[i]; - if ((r->start & ~0x80) == 0x374) { - r->start |= 2; - r->end = r->start; - } - } -} -DECLARE_PCI_FIXUP_HEADER(PCI_ANY_ID, PCI_ANY_ID, pci_fixup_ide_bases); - -char * __devinit pcibios_setup(char *str) -{ - return str; -} - static int sh5pci_read(struct pci_bus *bus, unsigned int devfn, int where, int size, u32 *val) { diff --git a/arch/sh/drivers/pci/ops-sh7785lcr.c b/arch/sh/drivers/pci/ops-sh7785lcr.c deleted file mode 100644 index fb0869f0bef..00000000000 --- a/arch/sh/drivers/pci/ops-sh7785lcr.c +++ /dev/null @@ -1,66 +0,0 @@ -/* - * Author: Ian DaSilva (idasilva@mvista.com) - * - * Highly leveraged from pci-bigsur.c, written by Dustin McIntire. - * - * May be copied or modified under the terms of the GNU General Public - * License. See linux/COPYING for more information. - * - * PCI initialization for the Renesas R0P7785LC0011RL board - * Based on arch/sh/drivers/pci/ops-r7780rp.c - * - */ -#include <linux/kernel.h> -#include <linux/types.h> -#include <linux/init.h> -#include <linux/delay.h> -#include <linux/pci.h> -#include "pci-sh4.h" - -static char irq_tab[] __initdata = { - 65, 66, 67, 68, -}; - -int __init pcibios_map_platform_irq(struct pci_dev *pdev, u8 slot, u8 pin) -{ - return irq_tab[slot]; -} - -static struct resource sh7785_io_resource = { - .name = "SH7785_IO", - .start = SH7780_PCI_IO_BASE, - .end = SH7780_PCI_IO_BASE + SH7780_PCI_IO_SIZE - 1, - .flags = IORESOURCE_IO -}; - -static struct resource sh7785_mem_resource = { - .name = "SH7785_mem", - .start = SH7780_PCI_MEMORY_BASE, - .end = SH7780_PCI_MEMORY_BASE + SH7780_PCI_MEM_SIZE - 1, - .flags = IORESOURCE_MEM -}; - -struct pci_channel board_pci_channels[] = { - { &sh4_pci_ops, &sh7785_io_resource, &sh7785_mem_resource, 0, 0xff }, - { NULL, NULL, NULL, 0, 0 }, -}; -EXPORT_SYMBOL(board_pci_channels); - -static struct sh4_pci_address_map sh7785_pci_map = { - .window0 = { -#if defined(CONFIG_32BIT) - .base = SH7780_32BIT_DDR_BASE_ADDR, - .size = 0x40000000, -#else - .base = SH7780_CS0_BASE_ADDR, - .size = 0x20000000, -#endif - }, - - .flags = SH4_PCIC_NO_RESET, -}; - -int __init pcibios_init_platform(void) -{ - return sh7780_pcic_init(&sh7785_pci_map); -} diff --git a/arch/sh/drivers/pci/ops-snapgear.c b/arch/sh/drivers/pci/ops-snapgear.c deleted file mode 100644 index 53dd893d4e5..00000000000 --- a/arch/sh/drivers/pci/ops-snapgear.c +++ /dev/null @@ -1,94 +0,0 @@ -/* - * arch/sh/drivers/pci/ops-snapgear.c - * - * Author: David McCullough <davidm@snapgear.com> - * - * Ported to new API by Paul Mundt <lethal@linux-sh.org> - * - * Highly leveraged from pci-bigsur.c, written by Dustin McIntire. - * - * May be copied or modified under the terms of the GNU General Public - * License. See linux/COPYING for more information. - * - * PCI initialization for the SnapGear boards - */ -#include <linux/kernel.h> -#include <linux/types.h> -#include <linux/init.h> -#include <linux/pci.h> -#include "pci-sh4.h" - -#define SNAPGEAR_PCI_IO 0x4000 -#define SNAPGEAR_PCI_MEM 0xfd000000 - -/* PCI: default LOCAL memory window sizes (seen from PCI bus) */ -#define SNAPGEAR_LSR0_SIZE (64*(1<<20)) //64MB -#define SNAPGEAR_LSR1_SIZE (64*(1<<20)) //64MB - -static struct resource sh7751_io_resource = { - .name = "SH7751 IO", - .start = SNAPGEAR_PCI_IO, - .end = SNAPGEAR_PCI_IO + (64*1024) - 1, /* 64KiB I/O */ - .flags = IORESOURCE_IO, -}; - -static struct resource sh7751_mem_resource = { - .name = "SH7751 mem", - .start = SNAPGEAR_PCI_MEM, - .end = SNAPGEAR_PCI_MEM + (64*1024*1024) - 1, /* 64MiB mem */ - .flags = IORESOURCE_MEM, -}; - -struct pci_channel board_pci_channels[] = { - { &sh4_pci_ops, &sh7751_io_resource, &sh7751_mem_resource, 0, 0xff }, - { 0, } -}; - -static struct sh4_pci_address_map sh7751_pci_map = { - .window0 = { - .base = SH7751_CS2_BASE_ADDR, - .size = SNAPGEAR_LSR0_SIZE, - }, - - .window1 = { - .base = SH7751_CS2_BASE_ADDR, - .size = SNAPGEAR_LSR1_SIZE, - }, - - .flags = SH4_PCIC_NO_RESET, -}; - -/* - * Initialize the SnapGear PCI interface - * Setup hardware to be Central Funtion - * Copy the BSR regs to the PCI interface - * Setup PCI windows into local RAM - */ -int __init pcibios_init_platform(void) -{ - return sh7751_pcic_init(&sh7751_pci_map); -} - -int __init pcibios_map_platform_irq(struct pci_dev *pdev, u8 slot, u8 pin) -{ - int irq = -1; - - switch (slot) { - case 8: /* the PCI bridge */ break; - case 11: irq = 8; break; /* USB */ - case 12: irq = 11; break; /* PCMCIA */ - case 13: irq = 5; break; /* eth0 */ - case 14: irq = 8; break; /* eth1 */ - case 15: irq = 11; break; /* safenet (unused) */ - } - - printk("PCI: Mapping SnapGear IRQ for slot %d, pin %c to irq %d\n", - slot, pin - 1 + 'A', irq); - - return irq; -} - -void __init pcibios_fixup(void) -{ - /* Nothing to fixup .. */ -} diff --git a/arch/sh/drivers/pci/pci-auto.c b/arch/sh/drivers/pci/pci-auto.c deleted file mode 100644 index cf48b12ee58..00000000000 --- a/arch/sh/drivers/pci/pci-auto.c +++ /dev/null @@ -1,545 +0,0 @@ -/* - * PCI autoconfiguration library - * - * Author: Matt Porter <mporter@mvista.com> - * - * Copyright 2000, 2001 MontaVista Software Inc. - * Copyright 2001 Bradley D. LaRonde <brad@ltc.com> - * Copyright 2003 Paul Mundt <lethal@linux-sh.org> - * - * This program is free software; you can redistribute it and/or modify it - * under the terms of the GNU General Public License as published by the - * Free Software Foundation; either version 2 of the License, or (at your - * option) any later version. - */ - -/* - * Modified for MIPS by Jun Sun, jsun@mvista.com - * - * . Simplify the interface between pci_auto and the rest: a single function. - * . Assign resources from low address to upper address. - * . change most int to u32. - * - * Further modified to include it as mips generic code, ppopov@mvista.com. - * - * 2001-10-26 Bradley D. LaRonde <brad@ltc.com> - * - Add a top_bus argument to the "early config" functions so that - * they can set a fake parent bus pointer to convince the underlying - * pci ops to use type 1 configuration for sub busses. - * - Set bridge base and limit registers correctly. - * - Align io and memory base properly before and after bridge setup. - * - Don't fall through to pci_setup_bars for bridge. - * - Reformat the debug output to look more like lspci's output. - * - * Cloned for SuperH by M. R. Brown, mrbrown@0xd6.org - * - * 2003-08-05 Paul Mundt <lethal@linux-sh.org> - * - Don't update the BAR values on systems that already have valid addresses - * and don't want these updated for whatever reason, by way of a new config - * option check. However, we still read in the old BAR values so that they - * can still be reported through the debug output. - */ - -#include <linux/kernel.h> -#include <linux/init.h> -#include <linux/types.h> -#include <linux/pci.h> - -#define DEBUG -#ifdef DEBUG -#define DBG(x...) printk(x) -#else -#define DBG(x...) -#endif - -/* - * These functions are used early on before PCI scanning is done - * and all of the pci_dev and pci_bus structures have been created. - */ -static struct pci_dev *fake_pci_dev(struct pci_channel *hose, - int top_bus, int busnr, int devfn) -{ - static struct pci_dev dev; - static struct pci_bus bus; - - dev.bus = &bus; - dev.sysdata = hose; - dev.devfn = devfn; - bus.number = busnr; - bus.ops = hose->pci_ops; - - if(busnr != top_bus) - /* Fake a parent bus structure. */ - bus.parent = &bus; - else - bus.parent = NULL; - - return &dev; -} - -#define EARLY_PCI_OP(rw, size, type) \ -static int early_##rw##_config_##size(struct pci_channel *hose, \ - int top_bus, int bus, int devfn, int offset, type value) \ -{ \ - return pci_##rw##_config_##size( \ - fake_pci_dev(hose, top_bus, bus, devfn), \ - offset, value); \ -} - -EARLY_PCI_OP(read, byte, u8 *) -EARLY_PCI_OP(read, word, u16 *) -EARLY_PCI_OP(read, dword, u32 *) -EARLY_PCI_OP(write, byte, u8) -EARLY_PCI_OP(write, word, u16) -EARLY_PCI_OP(write, dword, u32) - -static struct resource *io_resource_inuse; -static struct resource *mem_resource_inuse; - -static u32 pciauto_lower_iospc; -static u32 pciauto_upper_iospc; - -static u32 pciauto_lower_memspc; -static u32 pciauto_upper_memspc; - -static void __init -pciauto_setup_bars(struct pci_channel *hose, - int top_bus, - int current_bus, - int pci_devfn, - int bar_limit) -{ - u32 bar_response, bar_size, bar_value; - u32 bar, addr_mask, bar_nr = 0; - u32 * upper_limit; - u32 * lower_limit; - int found_mem64 = 0; - - for (bar = PCI_BASE_ADDRESS_0; bar <= bar_limit; bar+=4) { - u32 bar_addr; - - /* Read the old BAR value */ - early_read_config_dword(hose, top_bus, - current_bus, - pci_devfn, - bar, - &bar_addr); - - /* Tickle the BAR and get the response */ - early_write_config_dword(hose, top_bus, - current_bus, - pci_devfn, - bar, - 0xffffffff); - - early_read_config_dword(hose, top_bus, - current_bus, - pci_devfn, - bar, - &bar_response); - - /* - * Write the old BAR value back out, only update the BAR - * if we implicitly want resources to be updated, which - * is done by the generic code further down. -- PFM. - */ - early_write_config_dword(hose, top_bus, - current_bus, - pci_devfn, - bar, - bar_addr); - - /* If BAR is not implemented go to the next BAR */ - if (!bar_response) - continue; - - /* - * Workaround for a BAR that doesn't use its upper word, - * like the ALi 1535D+ PCI DC-97 Controller Modem (M5457). - * bdl <brad@ltc.com> - */ - if (!(bar_response & 0xffff0000)) - bar_response |= 0xffff0000; - -retry: - /* Check the BAR type and set our address mask */ - if (bar_response & PCI_BASE_ADDRESS_SPACE) { - addr_mask = PCI_BASE_ADDRESS_IO_MASK; - upper_limit = &pciauto_upper_iospc; - lower_limit = &pciauto_lower_iospc; - DBG(" I/O"); - } else { - if ((bar_response & PCI_BASE_ADDRESS_MEM_TYPE_MASK) == - PCI_BASE_ADDRESS_MEM_TYPE_64) - found_mem64 = 1; - - addr_mask = PCI_BASE_ADDRESS_MEM_MASK; - upper_limit = &pciauto_upper_memspc; - lower_limit = &pciauto_lower_memspc; - DBG(" Mem"); - } - - - /* Calculate requested size */ - bar_size = ~(bar_response & addr_mask) + 1; - - /* Allocate a base address */ - bar_value = ((*lower_limit - 1) & ~(bar_size - 1)) + bar_size; - - if ((bar_value + bar_size) > *upper_limit) { - if (bar_response & PCI_BASE_ADDRESS_SPACE) { - if (io_resource_inuse->child) { - io_resource_inuse = - io_resource_inuse->child; - pciauto_lower_iospc = - io_resource_inuse->start; - pciauto_upper_iospc = - io_resource_inuse->end + 1; - goto retry; - } - - } else { - if (mem_resource_inuse->child) { - mem_resource_inuse = - mem_resource_inuse->child; - pciauto_lower_memspc = - mem_resource_inuse->start; - pciauto_upper_memspc = - mem_resource_inuse->end + 1; - goto retry; - } - } - DBG(" unavailable -- skipping, value %x size %x\n", - bar_value, bar_size); - continue; - } - - if (bar_value < *lower_limit || (bar_value + bar_size) >= *upper_limit) { - DBG(" unavailable -- skipping, value %x size %x\n", - bar_value, bar_size); - continue; - } - -#ifdef CONFIG_PCI_AUTO_UPDATE_RESOURCES - /* Write it out and update our limit */ - early_write_config_dword(hose, top_bus, current_bus, pci_devfn, - bar, bar_value); -#endif - - *lower_limit = bar_value + bar_size; - - /* - * If we are a 64-bit decoder then increment to the - * upper 32 bits of the bar and force it to locate - * in the lower 4GB of memory. - */ - if (found_mem64) { - bar += 4; - early_write_config_dword(hose, top_bus, - current_bus, - pci_devfn, - bar, - 0x00000000); - } - - DBG(" at 0x%.8x [size=0x%x]\n", bar_value, bar_size); - - bar_nr++; - } - -} - -static void __init -pciauto_prescan_setup_bridge(struct pci_channel *hose, - int top_bus, - int current_bus, - int pci_devfn, - int sub_bus) -{ - /* Configure bus number registers */ - early_write_config_byte(hose, top_bus, current_bus, pci_devfn, - PCI_PRIMARY_BUS, current_bus); - early_write_config_byte(hose, top_bus, current_bus, pci_devfn, - PCI_SECONDARY_BUS, sub_bus + 1); - early_write_config_byte(hose, top_bus, current_bus, pci_devfn, - PCI_SUBORDINATE_BUS, 0xff); - - /* Align memory and I/O to 1MB and 4KB boundaries. */ - pciauto_lower_memspc = (pciauto_lower_memspc + (0x100000 - 1)) - & ~(0x100000 - 1); - pciauto_lower_iospc = (pciauto_lower_iospc + (0x1000 - 1)) - & ~(0x1000 - 1); - - /* Set base (lower limit) of address range behind bridge. */ - early_write_config_word(hose, top_bus, current_bus, pci_devfn, - PCI_MEMORY_BASE, pciauto_lower_memspc >> 16); - early_write_config_byte(hose, top_bus, current_bus, pci_devfn, - PCI_IO_BASE, (pciauto_lower_iospc & 0x0000f000) >> 8); - early_write_config_word(hose, top_bus, current_bus, pci_devfn, - PCI_IO_BASE_UPPER16, pciauto_lower_iospc >> 16); - - /* We don't support prefetchable memory for now, so disable */ - early_write_config_word(hose, top_bus, current_bus, pci_devfn, - PCI_PREF_MEMORY_BASE, 0); - early_write_config_word(hose, top_bus, current_bus, pci_devfn, - PCI_PREF_MEMORY_LIMIT, 0); -} - -static void __init -pciauto_postscan_setup_bridge(struct pci_channel *hose, - int top_bus, - int current_bus, - int pci_devfn, - int sub_bus) -{ - u32 temp; - - /* - * [jsun] we always bump up baselines a little, so that if there - * nothing behind P2P bridge, we don't wind up overlapping IO/MEM - * spaces. - */ - pciauto_lower_memspc += 1; - pciauto_lower_iospc += 1; - - /* Configure bus number registers */ - early_write_config_byte(hose, top_bus, current_bus, pci_devfn, - PCI_SUBORDINATE_BUS, sub_bus); - - /* Set upper limit of address range behind bridge. */ - early_write_config_word(hose, top_bus, current_bus, pci_devfn, - PCI_MEMORY_LIMIT, pciauto_lower_memspc >> 16); - early_write_config_byte(hose, top_bus, current_bus, pci_devfn, - PCI_IO_LIMIT, (pciauto_lower_iospc & 0x0000f000) >> 8); - early_write_config_word(hose, top_bus, current_bus, pci_devfn, - PCI_IO_LIMIT_UPPER16, pciauto_lower_iospc >> 16); - - /* Align memory and I/O to 1MB and 4KB boundaries. */ - pciauto_lower_memspc = (pciauto_lower_memspc + (0x100000 - 1)) - & ~(0x100000 - 1); - pciauto_lower_iospc = (pciauto_lower_iospc + (0x1000 - 1)) - & ~(0x1000 - 1); - - /* Enable memory and I/O accesses, enable bus master */ - early_read_config_dword(hose, top_bus, current_bus, pci_devfn, - PCI_COMMAND, &temp); - early_write_config_dword(hose, top_bus, current_bus, pci_devfn, - PCI_COMMAND, temp | PCI_COMMAND_IO | PCI_COMMAND_MEMORY - | PCI_COMMAND_MASTER); -} - -static void __init -pciauto_prescan_setup_cardbus_bridge(struct pci_channel *hose, - int top_bus, - int current_bus, - int pci_devfn, - int sub_bus) -{ - /* Configure bus number registers */ - early_write_config_byte(hose, top_bus, current_bus, pci_devfn, - PCI_PRIMARY_BUS, current_bus); - early_write_config_byte(hose, top_bus, current_bus, pci_devfn, - PCI_SECONDARY_BUS, sub_bus + 1); - early_write_config_byte(hose, top_bus, current_bus, pci_devfn, - PCI_SUBORDINATE_BUS, 0xff); - - /* Align memory and I/O to 4KB and 4 byte boundaries. */ - pciauto_lower_memspc = (pciauto_lower_memspc + (0x1000 - 1)) - & ~(0x1000 - 1); - pciauto_lower_iospc = (pciauto_lower_iospc + (0x4 - 1)) - & ~(0x4 - 1); - - early_write_config_dword(hose, top_bus, current_bus, pci_devfn, - PCI_CB_MEMORY_BASE_0, pciauto_lower_memspc); - early_write_config_dword(hose, top_bus, current_bus, pci_devfn, - PCI_CB_IO_BASE_0, pciauto_lower_iospc); -} - -static void __init -pciauto_postscan_setup_cardbus_bridge(struct pci_channel *hose, - int top_bus, - int current_bus, - int pci_devfn, - int sub_bus) -{ - u32 temp; - - /* - * [jsun] we always bump up baselines a little, so that if there - * nothing behind P2P bridge, we don't wind up overlapping IO/MEM - * spaces. - */ - pciauto_lower_memspc += 1; - pciauto_lower_iospc += 1; - - /* - * Configure subordinate bus number. The PCI subsystem - * bus scan will renumber buses (reserving three additional - * for this PCI<->CardBus bridge for the case where a CardBus - * adapter contains a P2P or CB2CB bridge. - */ - - early_write_config_byte(hose, top_bus, current_bus, pci_devfn, - PCI_SUBORDINATE_BUS, sub_bus); - - /* - * Reserve an additional 4MB for mem space and 16KB for - * I/O space. This should cover any additional space - * requirement of unusual CardBus devices with - * additional bridges that can consume more address space. - * - * Although pcmcia-cs currently will reprogram bridge - * windows, the goal is to add an option to leave them - * alone and use the bridge window ranges as the regions - * that are searched for free resources upon hot-insertion - * of a device. This will allow a PCI<->CardBus bridge - * configured by this routine to happily live behind a - * P2P bridge in a system. - */ - /* Align memory and I/O to 4KB and 4 byte boundaries. */ - pciauto_lower_memspc = (pciauto_lower_memspc + (0x1000 - 1)) - & ~(0x1000 - 1); - pciauto_lower_iospc = (pciauto_lower_iospc + (0x4 - 1)) - & ~(0x4 - 1); - /* Set up memory and I/O filter limits, assume 32-bit I/O space */ - early_write_config_dword(hose, top_bus, current_bus, pci_devfn, - PCI_CB_MEMORY_LIMIT_0, pciauto_lower_memspc - 1); - early_write_config_dword(hose, top_bus, current_bus, pci_devfn, - PCI_CB_IO_LIMIT_0, pciauto_lower_iospc - 1); - - /* Enable memory and I/O accesses, enable bus master */ - early_read_config_dword(hose, top_bus, current_bus, pci_devfn, - PCI_COMMAND, &temp); - early_write_config_dword(hose, top_bus, current_bus, pci_devfn, - PCI_COMMAND, temp | PCI_COMMAND_IO | PCI_COMMAND_MEMORY | - PCI_COMMAND_MASTER); -} - -#define PCIAUTO_IDE_MODE_MASK 0x05 - -static int __init -pciauto_bus_scan(struct pci_channel *hose, int top_bus, int current_bus) -{ - int sub_bus; - u32 pci_devfn, pci_class, cmdstat, found_multi=0; - unsigned short vid, did; - unsigned char header_type; - int devfn_start = 0; - int devfn_stop = 0xff; - - sub_bus = current_bus; - - if (hose->first_devfn) - devfn_start = hose->first_devfn; - if (hose->last_devfn) - devfn_stop = hose->last_devfn; - - for (pci_devfn=devfn_start; pci_devfn<devfn_stop; pci_devfn++) { - - if (PCI_FUNC(pci_devfn) && !found_multi) - continue; - - early_read_config_word(hose, top_bus, current_bus, pci_devfn, - PCI_VENDOR_ID, &vid); - - if (vid == 0xffff) continue; - - early_read_config_byte(hose, top_bus, current_bus, pci_devfn, - PCI_HEADER_TYPE, &header_type); - - if (!PCI_FUNC(pci_devfn)) - found_multi = header_type & 0x80; - - early_read_config_word(hose, top_bus, current_bus, pci_devfn, - PCI_DEVICE_ID, &did); - - early_read_config_dword(hose, top_bus, current_bus, pci_devfn, - PCI_CLASS_REVISION, &pci_class); - - DBG("%.2x:%.2x.%x Class %.4x: %.4x:%.4x", - current_bus, PCI_SLOT(pci_devfn), PCI_FUNC(pci_devfn), - pci_class >> 16, vid, did); - if (pci_class & 0xff) - DBG(" (rev %.2x)", pci_class & 0xff); - DBG("\n"); - - if ((pci_class >> 16) == PCI_CLASS_BRIDGE_PCI) { - DBG(" Bridge: primary=%.2x, secondary=%.2x\n", - current_bus, sub_bus + 1); - pciauto_prescan_setup_bridge(hose, top_bus, current_bus, - pci_devfn, sub_bus); - DBG("Scanning sub bus %.2x, I/O 0x%.8x, Mem 0x%.8x\n", - sub_bus + 1, - pciauto_lower_iospc, pciauto_lower_memspc); - sub_bus = pciauto_bus_scan(hose, top_bus, sub_bus+1); - DBG("Back to bus %.2x\n", current_bus); - pciauto_postscan_setup_bridge(hose, top_bus, current_bus, - pci_devfn, sub_bus); - continue; - } else if ((pci_class >> 16) == PCI_CLASS_BRIDGE_CARDBUS) { - DBG(" CARDBUS Bridge: primary=%.2x, secondary=%.2x\n", - current_bus, sub_bus + 1); - DBG("PCI Autoconfig: Found CardBus bridge, device %d function %d\n", PCI_SLOT(pci_devfn), PCI_FUNC(pci_devfn)); - /* Place CardBus Socket/ExCA registers */ - pciauto_setup_bars(hose, top_bus, current_bus, pci_devfn, PCI_BASE_ADDRESS_0); - - pciauto_prescan_setup_cardbus_bridge(hose, top_bus, - current_bus, pci_devfn, sub_bus); - - DBG("Scanning sub bus %.2x, I/O 0x%.8x, Mem 0x%.8x\n", - sub_bus + 1, - pciauto_lower_iospc, pciauto_lower_memspc); - sub_bus = pciauto_bus_scan(hose, top_bus, sub_bus+1); - DBG("Back to bus %.2x, sub_bus is %x\n", current_bus, sub_bus); - pciauto_postscan_setup_cardbus_bridge(hose, top_bus, - current_bus, pci_devfn, sub_bus); - continue; - } else if ((pci_class >> 16) == PCI_CLASS_STORAGE_IDE) { - - unsigned char prg_iface; - - early_read_config_byte(hose, top_bus, current_bus, - pci_devfn, PCI_CLASS_PROG, &prg_iface); - if (!(prg_iface & PCIAUTO_IDE_MODE_MASK)) { - DBG("Skipping legacy mode IDE controller\n"); - continue; - } - } - - /* - * Found a peripheral, enable some standard - * settings - */ - early_read_config_dword(hose, top_bus, current_bus, pci_devfn, - PCI_COMMAND, &cmdstat); - early_write_config_dword(hose, top_bus, current_bus, pci_devfn, - PCI_COMMAND, cmdstat | PCI_COMMAND_IO | - PCI_COMMAND_MEMORY | - PCI_COMMAND_MASTER); - early_write_config_byte(hose, top_bus, current_bus, pci_devfn, - PCI_LATENCY_TIMER, 0x80); - - /* Allocate PCI I/O and/or memory space */ - pciauto_setup_bars(hose, top_bus, current_bus, pci_devfn, PCI_BASE_ADDRESS_5); - } - return sub_bus; -} - -int __init -pciauto_assign_resources(int busno, struct pci_channel *hose) -{ - /* setup resource limits */ - io_resource_inuse = hose->io_resource; - mem_resource_inuse = hose->mem_resource; - - pciauto_lower_iospc = io_resource_inuse->start; - pciauto_upper_iospc = io_resource_inuse->end + 1; - pciauto_lower_memspc = mem_resource_inuse->start; - pciauto_upper_memspc = mem_resource_inuse->end + 1; - DBG("Autoconfig PCI channel 0x%p\n", hose); - DBG("Scanning bus %.2x, I/O 0x%.8x:0x%.8x, Mem 0x%.8x:0x%.8x\n", - busno, pciauto_lower_iospc, pciauto_upper_iospc, - pciauto_lower_memspc, pciauto_upper_memspc); - - return pciauto_bus_scan(hose, busno, busno); -} diff --git a/arch/sh/drivers/pci/pci-dreamcast.c b/arch/sh/drivers/pci/pci-dreamcast.c new file mode 100644 index 00000000000..210f9d4af14 --- /dev/null +++ b/arch/sh/drivers/pci/pci-dreamcast.c @@ -0,0 +1,102 @@ +/* + * PCI support for the Sega Dreamcast + * + * Copyright (C) 2001, 2002 M. R. Brown + * Copyright (C) 2002, 2003 Paul Mundt + * + * This file originally bore the message (with enclosed-$): + * Id: pci.c,v 1.3 2003/05/04 19:29:46 lethal Exp + * Dreamcast PCI: Supports SEGA Broadband Adaptor only. + * + * This file is subject to the terms and conditions of the GNU General Public + * License. See the file "COPYING" in the main directory of this archive + * for more details. + */ + +#include <linux/sched.h> +#include <linux/kernel.h> +#include <linux/param.h> +#include <linux/interrupt.h> +#include <linux/init.h> +#include <linux/irq.h> +#include <linux/pci.h> +#include <linux/module.h> +#include <asm/io.h> +#include <asm/irq.h> +#include <mach/pci.h> + +static struct resource gapspci_io_resource = { + .name = "GAPSPCI IO", + .start = GAPSPCI_BBA_CONFIG, + .end = GAPSPCI_BBA_CONFIG + GAPSPCI_BBA_CONFIG_SIZE - 1, + .flags = IORESOURCE_IO, +}; + +static struct resource gapspci_mem_resource = { + .name = "GAPSPCI mem", + .start = GAPSPCI_DMA_BASE, + .end = GAPSPCI_DMA_BASE + GAPSPCI_DMA_SIZE - 1, + .flags = IORESOURCE_MEM, +}; + +static struct pci_channel dreamcast_pci_controller = { + .pci_ops = &gapspci_pci_ops, + .io_resource = &gapspci_io_resource, + .io_offset = 0x00000000, + .mem_resource = &gapspci_mem_resource, + .mem_offset = 0x00000000, +}; + +/* + * gapspci init + */ + +static int __init gapspci_init(void) +{ + char idbuf[16]; + int i; + + /* + * FIXME: All of this wants documenting to some degree, + * even some basic register definitions would be nice. + * + * I haven't seen anything this ugly since.. maple. + */ + + for (i=0; i<16; i++) + idbuf[i] = inb(GAPSPCI_REGS+i); + + if (strncmp(idbuf, "GAPSPCI_BRIDGE_2", 16)) + return -ENODEV; + + outl(0x5a14a501, GAPSPCI_REGS+0x18); + + for (i=0; i<1000000; i++) + cpu_relax(); + + if (inl(GAPSPCI_REGS+0x18) != 1) + return -EINVAL; + + outl(0x01000000, GAPSPCI_REGS+0x20); + outl(0x01000000, GAPSPCI_REGS+0x24); + + outl(GAPSPCI_DMA_BASE, GAPSPCI_REGS+0x28); + outl(GAPSPCI_DMA_BASE+GAPSPCI_DMA_SIZE, GAPSPCI_REGS+0x2c); + + outl(1, GAPSPCI_REGS+0x14); + outl(1, GAPSPCI_REGS+0x34); + + /* Setting Broadband Adapter */ + outw(0xf900, GAPSPCI_BBA_CONFIG+0x06); + outl(0x00000000, GAPSPCI_BBA_CONFIG+0x30); + outb(0x00, GAPSPCI_BBA_CONFIG+0x3c); + outb(0xf0, GAPSPCI_BBA_CONFIG+0x0d); + outw(0x0006, GAPSPCI_BBA_CONFIG+0x04); + outl(0x00002001, GAPSPCI_BBA_CONFIG+0x10); + outl(0x01000000, GAPSPCI_BBA_CONFIG+0x14); + + register_pci_controller(&dreamcast_pci_controller); + + return 0; +} +arch_initcall(gapspci_init); diff --git a/arch/sh/drivers/pci/pci-sh4.h b/arch/sh/drivers/pci/pci-sh4.h index a83dcf70c13..3d5296cde62 100644 --- a/arch/sh/drivers/pci/pci-sh4.h +++ b/arch/sh/drivers/pci/pci-sh4.h @@ -149,13 +149,10 @@ #define SH4_PCIPDTR_PB0 0x000000001 /* Port 0 Enable */ #define SH4_PCIPDR 0x220 /* Port IO Data Register */ -/* Flags */ -#define SH4_PCIC_NO_RESET 0x0001 - /* arch/sh/kernel/drivers/pci/ops-sh4.c */ extern struct pci_ops sh4_pci_ops; -int sh4_pci_check_direct(void); -int pci_fixup_pcic(void); +int sh4_pci_check_direct(struct pci_channel *chan); +int pci_fixup_pcic(struct pci_channel *chan); struct sh4_pci_address_space { unsigned long base; @@ -165,16 +162,18 @@ struct sh4_pci_address_space { struct sh4_pci_address_map { struct sh4_pci_address_space window0; struct sh4_pci_address_space window1; - unsigned long flags; }; -static inline void pci_write_reg(unsigned long val, unsigned long reg) +static inline void pci_write_reg(struct pci_channel *chan, + unsigned long val, unsigned long reg) { - ctrl_outl(val, PCI_REG(reg)); + ctrl_outl(val, chan->reg_base + reg); } -static inline unsigned long pci_read_reg(unsigned long reg) +static inline unsigned long pci_read_reg(struct pci_channel *chan, + unsigned long reg) { - return ctrl_inl(PCI_REG(reg)); + return ctrl_inl(chan->reg_base + reg); } + #endif /* __PCI_SH4_H */ diff --git a/arch/sh/drivers/pci/pci-sh5.c b/arch/sh/drivers/pci/pci-sh5.c index 7a97438762c..873ed2b4405 100644 --- a/arch/sh/drivers/pci/pci-sh5.c +++ b/arch/sh/drivers/pci/pci-sh5.c @@ -89,8 +89,21 @@ static irqreturn_t pcish5_serr_irq(int irq, void *dev_id) return IRQ_NONE; } -int __init sh5pci_init(unsigned long memStart, unsigned long memSize) +static struct resource sh5_io_resource = { /* place holder */ }; +static struct resource sh5_mem_resource = { /* place holder */ }; + +static struct pci_channel sh5pci_controller = { + .pci_ops = &sh5_pci_ops, + .mem_resource = &sh5_mem_resource, + .mem_offset = 0x00000000, + .io_resource = &sh5_io_resource, + .io_offset = 0x00000000, +}; + +static int __init sh5pci_init(void) { + unsigned long memStart = __pa(memory_start); + unsigned long memSize = __pa(memory_end) - memStart; u32 lsr0; u32 uval; @@ -106,12 +119,12 @@ int __init sh5pci_init(unsigned long memStart, unsigned long memSize) return -EINVAL; } - pcicr_virt = onchip_remap(SH5PCI_ICR_BASE, 1024, "PCICR"); + pcicr_virt = (unsigned long)ioremap_nocache(SH5PCI_ICR_BASE, 1024); if (!pcicr_virt) { panic("Unable to remap PCICR\n"); } - PCI_IO_AREA = onchip_remap(SH5PCI_IO_BASE, 0x10000, "PCIIO"); + PCI_IO_AREA = (unsigned long)ioremap_nocache(SH5PCI_IO_BASE, 0x10000); if (!PCI_IO_AREA) { panic("Unable to remap PCIIO\n"); } @@ -197,32 +210,14 @@ int __init sh5pci_init(unsigned long memStart, unsigned long memSize) SH5PCI_WRITE(AINTM, ~0); SH5PCI_WRITE(PINTM, ~0); - return 0; -} + sh5_io_resource.start = PCI_IO_AREA; + sh5_io_resource.end = PCI_IO_AREA + 0x10000; -void __devinit pcibios_fixup_bus(struct pci_bus *bus) -{ - struct pci_dev *dev = bus->self; - int i; - - if (dev) { - for (i= 0; i < 3; i++) { - bus->resource[i] = - &dev->resource[PCI_BRIDGE_RESOURCES+i]; - bus->resource[i]->name = bus->name; - } - bus->resource[0]->flags |= IORESOURCE_IO; - bus->resource[1]->flags |= IORESOURCE_MEM; - - /* For now, propagate host limits to the bus; - * we'll adjust them later. */ - bus->resource[0]->end = 64*1024 - 1 ; - bus->resource[1]->end = PCIBIOS_MIN_MEM+(256*1024*1024)-1; - bus->resource[0]->start = PCIBIOS_MIN_IO; - bus->resource[1]->start = PCIBIOS_MIN_MEM; - - /* Turn off downstream PF memory address range by default */ - bus->resource[2]->start = 1024*1024; - bus->resource[2]->end = bus->resource[2]->start - 1; - } + sh5_mem_resource.start = memStart; + sh5_mem_resource.end = memStart + memSize; + + register_pci_controller(&sh5pci_controller); + + return 0; } +arch_initcall(sh5pci_init); diff --git a/arch/sh/drivers/pci/pci-sh5.h b/arch/sh/drivers/pci/pci-sh5.h index 7cff3fc04d3..f277628221f 100644 --- a/arch/sh/drivers/pci/pci-sh5.h +++ b/arch/sh/drivers/pci/pci-sh5.h @@ -107,7 +107,4 @@ extern unsigned long pcicr_virt; extern struct pci_ops sh5_pci_ops; -/* arch/sh/drivers/pci/pci-sh5.c */ -int sh5pci_init(unsigned long memStart, unsigned long memSize); - #endif /* __PCI_SH5_H */ diff --git a/arch/sh/drivers/pci/pci-sh7751.c b/arch/sh/drivers/pci/pci-sh7751.c index 3065eb184f0..c4fa0bb1397 100644 --- a/arch/sh/drivers/pci/pci-sh7751.c +++ b/arch/sh/drivers/pci/pci-sh7751.c @@ -1,88 +1,99 @@ /* - * Low-Level PCI Support for the SH7751 + * Low-Level PCI Support for the SH7751 * - * Dustin McIntire (dustin@sensoria.com) - * Derived from arch/i386/kernel/pci-*.c which bore the message: - * (c) 1999--2000 Martin Mares <mj@ucw.cz> + * Copyright (C) 2003 - 2009 Paul Mundt + * Copyright (C) 2001 Dustin McIntire * - * Ported to the new API by Paul Mundt <lethal@linux-sh.org> - * With cleanup by Paul van Gool <pvangool@mimotech.com> - * - * May be copied or modified under the terms of the GNU General Public - * License. See linux/COPYING for more information. + * With cleanup by Paul van Gool <pvangool@mimotech.com>, 2003. * + * This file is subject to the terms and conditions of the GNU General Public + * License. See the file "COPYING" in the main directory of this archive + * for more details. */ -#undef DEBUG - #include <linux/init.h> #include <linux/pci.h> #include <linux/types.h> #include <linux/errno.h> -#include <linux/delay.h> +#include <linux/io.h> #include "pci-sh4.h" #include <asm/addrspace.h> -#include <asm/io.h> -/* - * Initialization. Try all known PCI access methods. Note that we support - * using both PCI BIOS and direct access: in such cases, we use I/O ports - * to access config space. - * - * Note that the platform specific initialization (BSC registers, and memory - * space mapping) will be called via the platform defined function - * pcibios_init_platform(). - */ -static int __init sh7751_pci_init(void) +static int __init __area_sdram_check(struct pci_channel *chan, + unsigned int area) { - unsigned int id; - int ret; - - pr_debug("PCI: Starting intialization.\n"); + unsigned long word; - /* check for SH7751/SH7751R hardware */ - id = pci_read_reg(SH7751_PCICONF0); - if (id != ((SH7751_DEVICE_ID << 16) | SH7751_VENDOR_ID) && - id != ((SH7751R_DEVICE_ID << 16) | SH7751_VENDOR_ID)) { - pr_debug("PCI: This is not an SH7751(R) (%x)\n", id); - return -ENODEV; - } - - if ((ret = sh4_pci_check_direct()) != 0) - return ret; - - return pcibios_init_platform(); -} -subsys_initcall(sh7751_pci_init); - -static int __init __area_sdram_check(unsigned int area) -{ - u32 word; - - word = ctrl_inl(SH7751_BCR1); + word = __raw_readl(SH7751_BCR1); /* check BCR for SDRAM in area */ if (((word >> area) & 1) == 0) { - printk("PCI: Area %d is not configured for SDRAM. BCR1=0x%x\n", + printk("PCI: Area %d is not configured for SDRAM. BCR1=0x%lx\n", area, word); return 0; } - pci_write_reg(word, SH4_PCIBCR1); + pci_write_reg(chan, word, SH4_PCIBCR1); - word = (u16)ctrl_inw(SH7751_BCR2); + word = __raw_readw(SH7751_BCR2); /* check BCR2 for 32bit SDRAM interface*/ if (((word >> (area << 1)) & 0x3) != 0x3) { - printk("PCI: Area %d is not 32 bit SDRAM. BCR2=0x%x\n", + printk("PCI: Area %d is not 32 bit SDRAM. BCR2=0x%lx\n", area, word); return 0; } - pci_write_reg(word, SH4_PCIBCR2); + pci_write_reg(chan, word, SH4_PCIBCR2); return 1; } -int __init sh7751_pcic_init(struct sh4_pci_address_map *map) +static struct resource sh7751_io_resource = { + .name = "SH7751_IO", + .start = SH7751_PCI_IO_BASE, + .end = SH7751_PCI_IO_BASE + SH7751_PCI_IO_SIZE - 1, + .flags = IORESOURCE_IO +}; + +static struct resource sh7751_mem_resource = { + .name = "SH7785_mem", + .start = SH7751_PCI_MEMORY_BASE, + .end = SH7751_PCI_MEMORY_BASE + SH7751_PCI_MEM_SIZE - 1, + .flags = IORESOURCE_MEM +}; + +static struct pci_channel sh7751_pci_controller = { + .pci_ops = &sh4_pci_ops, + .mem_resource = &sh7751_mem_resource, + .mem_offset = 0x00000000, + .io_resource = &sh7751_io_resource, + .io_offset = 0x00000000, +}; + +static struct sh4_pci_address_map sh7751_pci_map = { + .window0 = { + .base = SH7751_CS3_BASE_ADDR, + .size = 0x04000000, + }, +}; + +static int __init sh7751_pci_init(void) { - u32 reg; - u32 word; + struct pci_channel *chan = &sh7751_pci_controller; + unsigned int id; + u32 word, reg; + int ret; + + printk(KERN_NOTICE "PCI: Starting intialization.\n"); + + chan->reg_base = 0xfe200000; + + /* check for SH7751/SH7751R hardware */ + id = pci_read_reg(chan, SH7751_PCICONF0); + if (id != ((SH7751_DEVICE_ID << 16) | SH7751_VENDOR_ID) && + id != ((SH7751R_DEVICE_ID << 16) | SH7751_VENDOR_ID)) { + pr_debug("PCI: This is not an SH7751(R) (%x)\n", id); + return -ENODEV; + } + + if ((ret = sh4_pci_check_direct(chan)) != 0) + return ret; /* Set the BCR's to enable PCI access */ reg = ctrl_inl(SH7751_BCR1); @@ -90,25 +101,10 @@ int __init sh7751_pcic_init(struct sh4_pci_address_map *map) ctrl_outl(reg, SH7751_BCR1); /* Turn the clocks back on (not done in reset)*/ - pci_write_reg(0, SH4_PCICLKR); + pci_write_reg(chan, 0, SH4_PCICLKR); /* Clear Powerdown IRQ's (not done in reset) */ word = SH4_PCIPINT_D3 | SH4_PCIPINT_D0; - pci_write_reg(word, SH4_PCIPINT); - - /* - * This code is unused for some boards as it is done in the - * bootloader and doing it here means the MAC addresses loaded - * by the bootloader get lost. - */ - if (!(map->flags & SH4_PCIC_NO_RESET)) { - /* toggle PCI reset pin */ - word = SH4_PCICR_PREFIX | SH4_PCICR_PRST; - pci_write_reg(word, SH4_PCICR); - /* Wait for a long time... not 1 sec. but long enough */ - mdelay(100); - word = SH4_PCICR_PREFIX; - pci_write_reg(word, SH4_PCICR); - } + pci_write_reg(chan, word, SH4_PCIPINT); /* set the command/status bits to: * Wait Cycle Control + Parity Enable + Bus Master + @@ -116,89 +112,77 @@ int __init sh7751_pcic_init(struct sh4_pci_address_map *map) */ word = SH7751_PCICONF1_WCC | SH7751_PCICONF1_PER | SH7751_PCICONF1_BUM | SH7751_PCICONF1_MES; - pci_write_reg(word, SH7751_PCICONF1); + pci_write_reg(chan, word, SH7751_PCICONF1); /* define this host as the host bridge */ word = PCI_BASE_CLASS_BRIDGE << 24; - pci_write_reg(word, SH7751_PCICONF2); + pci_write_reg(chan, word, SH7751_PCICONF2); /* Set IO and Mem windows to local address * Make PCI and local address the same for easy 1 to 1 mapping - * Window0 = map->window0.size @ non-cached area base = SDRAM - * Window1 = map->window1.size @ cached area base = SDRAM */ - word = map->window0.size - 1; - pci_write_reg(word, SH4_PCILSR0); - word = map->window1.size - 1; - pci_write_reg(word, SH4_PCILSR1); + word = sh7751_pci_map.window0.size - 1; + pci_write_reg(chan, word, SH4_PCILSR0); /* Set the values on window 0 PCI config registers */ - word = P2SEGADDR(map->window0.base); - pci_write_reg(word, SH4_PCILAR0); - pci_write_reg(word, SH7751_PCICONF5); - /* Set the values on window 1 PCI config registers */ - word = PHYSADDR(map->window1.base); - pci_write_reg(word, SH4_PCILAR1); - pci_write_reg(word, SH7751_PCICONF6); + word = P2SEGADDR(sh7751_pci_map.window0.base); + pci_write_reg(chan, word, SH4_PCILAR0); + pci_write_reg(chan, word, SH7751_PCICONF5); /* Set the local 16MB PCI memory space window to * the lowest PCI mapped address */ - word = PCIBIOS_MIN_MEM & SH4_PCIMBR_MASK; + word = chan->mem_resource->start & SH4_PCIMBR_MASK; pr_debug("PCI: Setting upper bits of Memory window to 0x%x\n", word); - pci_write_reg(word , SH4_PCIMBR); - - /* Map IO space into PCI IO window - * The IO window is 64K-PCIBIOS_MIN_IO in size - * IO addresses will be translated to the - * PCI IO window base address - */ - pr_debug("PCI: Mapping IO address 0x%x - 0x%x to base 0x%x\n", - PCIBIOS_MIN_IO, (64 << 10), - SH7751_PCI_IO_BASE + PCIBIOS_MIN_IO); + pci_write_reg(chan, word , SH4_PCIMBR); /* Make sure the MSB's of IO window are set to access PCI space * correctly */ - word = PCIBIOS_MIN_IO & SH4_PCIIOBR_MASK; + word = chan->io_resource->start & SH4_PCIIOBR_MASK; pr_debug("PCI: Setting upper bits of IO window to 0x%x\n", word); - pci_write_reg(word, SH4_PCIIOBR); + pci_write_reg(chan, word, SH4_PCIIOBR); /* Set PCI WCRx, BCRx's, copy from BSC locations */ /* check BCR for SDRAM in specified area */ - switch (map->window0.base) { - case SH7751_CS0_BASE_ADDR: word = __area_sdram_check(0); break; - case SH7751_CS1_BASE_ADDR: word = __area_sdram_check(1); break; - case SH7751_CS2_BASE_ADDR: word = __area_sdram_check(2); break; - case SH7751_CS3_BASE_ADDR: word = __area_sdram_check(3); break; - case SH7751_CS4_BASE_ADDR: word = __area_sdram_check(4); break; - case SH7751_CS5_BASE_ADDR: word = __area_sdram_check(5); break; - case SH7751_CS6_BASE_ADDR: word = __area_sdram_check(6); break; + switch (sh7751_pci_map.window0.base) { + case SH7751_CS0_BASE_ADDR: word = __area_sdram_check(chan, 0); break; + case SH7751_CS1_BASE_ADDR: word = __area_sdram_check(chan, 1); break; + case SH7751_CS2_BASE_ADDR: word = __area_sdram_check(chan, 2); break; + case SH7751_CS3_BASE_ADDR: word = __area_sdram_check(chan, 3); break; + case SH7751_CS4_BASE_ADDR: word = __area_sdram_check(chan, 4); break; + case SH7751_CS5_BASE_ADDR: word = __area_sdram_check(chan, 5); break; + case SH7751_CS6_BASE_ADDR: word = __area_sdram_check(chan, 6); break; } if (!word) - return 0; + return -1; /* configure the wait control registers */ word = ctrl_inl(SH7751_WCR1); - pci_write_reg(word, SH4_PCIWCR1); + pci_write_reg(chan, word, SH4_PCIWCR1); word = ctrl_inl(SH7751_WCR2); - pci_write_reg(word, SH4_PCIWCR2); + pci_write_reg(chan, word, SH4_PCIWCR2); word = ctrl_inl(SH7751_WCR3); - pci_write_reg(word, SH4_PCIWCR3); + pci_write_reg(chan, word, SH4_PCIWCR3); word = ctrl_inl(SH7751_MCR); - pci_write_reg(word, SH4_PCIMCR); + pci_write_reg(chan, word, SH4_PCIMCR); /* NOTE: I'm ignoring the PCI error IRQs for now.. * TODO: add support for the internal error interrupts and * DMA interrupts... */ - pci_fixup_pcic(); + pci_fixup_pcic(chan); /* SH7751 init done, set central function init complete */ /* use round robin mode to stop a device starving/overruning */ word = SH4_PCICR_PREFIX | SH4_PCICR_CFIN | SH4_PCICR_ARBM; - pci_write_reg(word, SH4_PCICR); + pci_write_reg(chan, word, SH4_PCICR); - return 1; + __set_io_port_base(SH7751_PCI_IO_BASE); + + register_pci_controller(chan); + + return 0; } +arch_initcall(sh7751_pci_init); diff --git a/arch/sh/drivers/pci/pci-sh7751.h b/arch/sh/drivers/pci/pci-sh7751.h index 68e3cb5e6be..4983a4d2035 100644 --- a/arch/sh/drivers/pci/pci-sh7751.h +++ b/arch/sh/drivers/pci/pci-sh7751.h @@ -26,7 +26,6 @@ #define SH7751_PCI_IO_SIZE 0x40000 /* Size of IO window */ #define SH7751_PCIREG_BASE 0xFE200000 /* PCI regs base address */ -#define PCI_REG(n) (SH7751_PCIREG_BASE+ n) #define SH7751_PCICONF0 0x0 /* PCI Config Reg 0 */ #define SH7751_PCICONF0_DEVID 0xFFFF0000 /* Device ID */ @@ -58,7 +57,7 @@ #define SH7751_PCICONF2_SCC 0x00FF0000 /* Sub-Class Code */ #define SH7751_PCICONF2_RLPI 0x0000FF00 /* Programming Interface */ #define SH7751_PCICONF2_REV 0x000000FF /* Revision ID */ -#define SH7751_PCICONF3 0xC /* PCI Config Reg 3 */ +#define SH7751_PCICONF3 0xC /* PCI Config Reg 3 */ #define SH7751_PCICONF3_BIST7 0x80000000 /* Bist Supported */ #define SH7751_PCICONF3_BIST6 0x40000000 /* Bist Executing */ #define SH7751_PCICONF3_BIST3_0 0x0F000000 /* Bist Passed */ @@ -73,12 +72,12 @@ #define SH7751_PCICONF5_BASE 0xFFFFFFF0 /* Mem Space Base Addr */ #define SH7751_PCICONF5_LAP 0x00000008 /* Prefetch Enabled */ #define SH7751_PCICONF5_LAT 0x00000006 /* Local Memory type */ - #define SH7751_PCICONF5_ASI 0x00000001 /* Address Space Type */ + #define SH7751_PCICONF5_ASI 0x00000001 /* Address Space Type */ #define SH7751_PCICONF6 0x18 /* PCI Config Reg 6 */ #define SH7751_PCICONF6_BASE 0xFFFFFFF0 /* Mem Space Base Addr */ #define SH7751_PCICONF6_LAP 0x00000008 /* Prefetch Enabled */ #define SH7751_PCICONF6_LAT 0x00000006 /* Local Memory type */ - #define SH7751_PCICONF6_ASI 0x00000001 /* Address Space Type */ + #define SH7751_PCICONF6_ASI 0x00000001 /* Address Space Type */ /* PCICONF7 - PCICONF10 are undefined */ #define SH7751_PCICONF11 0x2C /* PCI Config Reg 11 */ #define SH7751_PCICONF11_SSID 0xFFFF0000 /* Subsystem ID */ @@ -127,9 +126,4 @@ #define SH7751_CS5_BASE_ADDR (SH7751_CS4_BASE_ADDR + SH7751_MEM_REGION_SIZE) #define SH7751_CS6_BASE_ADDR (SH7751_CS5_BASE_ADDR + SH7751_MEM_REGION_SIZE) -struct sh4_pci_address_map; - -/* arch/sh/drivers/pci/pci-sh7751.c */ -int sh7751_pcic_init(struct sh4_pci_address_map *map); - #endif /* _PCI_SH7751_H_ */ diff --git a/arch/sh/drivers/pci/pci-sh7780.c b/arch/sh/drivers/pci/pci-sh7780.c index bae6a2cf047..ae13ff925c6 100644 --- a/arch/sh/drivers/pci/pci-sh7780.c +++ b/arch/sh/drivers/pci/pci-sh7780.c @@ -1,19 +1,12 @@ /* - * Low-Level PCI Support for the SH7780 + * Low-Level PCI Support for the SH7780 * - * Dustin McIntire (dustin@sensoria.com) - * Derived from arch/i386/kernel/pci-*.c which bore the message: - * (c) 1999--2000 Martin Mares <mj@ucw.cz> - * - * Ported to the new API by Paul Mundt <lethal@linux-sh.org> - * With cleanup by Paul van Gool <pvangool@mimotech.com> - * - * May be copied or modified under the terms of the GNU General Public - * License. See linux/COPYING for more information. + * Copyright (C) 2005 - 2009 Paul Mundt * + * This file is subject to the terms and conditions of the GNU General Public + * License. See the file "COPYING" in the main directory of this archive + * for more details. */ -#undef DEBUG - #include <linux/types.h> #include <linux/kernel.h> #include <linux/init.h> @@ -22,135 +15,137 @@ #include <linux/delay.h> #include "pci-sh4.h" -#define INTC_BASE 0xffd00000 -#define INTC_ICR0 (INTC_BASE+0x0) -#define INTC_ICR1 (INTC_BASE+0x1c) -#define INTC_INTPRI (INTC_BASE+0x10) -#define INTC_INTREQ (INTC_BASE+0x24) -#define INTC_INTMSK0 (INTC_BASE+0x44) -#define INTC_INTMSK1 (INTC_BASE+0x48) -#define INTC_INTMSK2 (INTC_BASE+0x40080) -#define INTC_INTMSKCLR0 (INTC_BASE+0x64) -#define INTC_INTMSKCLR1 (INTC_BASE+0x68) -#define INTC_INTMSKCLR2 (INTC_BASE+0x40084) -#define INTC_INT2MSKR (INTC_BASE+0x40038) -#define INTC_INT2MSKCR (INTC_BASE+0x4003c) +extern u8 pci_cache_line_size; + +static struct resource sh7785_io_resource = { + .name = "SH7785_IO", + .start = SH7780_PCI_IO_BASE, + .end = SH7780_PCI_IO_BASE + SH7780_PCI_IO_SIZE - 1, + .flags = IORESOURCE_IO +}; + +static struct resource sh7785_mem_resource = { + .name = "SH7785_mem", + .start = SH7780_PCI_MEMORY_BASE, + .end = SH7780_PCI_MEMORY_BASE + SH7780_PCI_MEM_SIZE - 1, + .flags = IORESOURCE_MEM +}; + +static struct pci_channel sh7780_pci_controller = { + .pci_ops = &sh4_pci_ops, + .mem_resource = &sh7785_mem_resource, + .mem_offset = 0x00000000, + .io_resource = &sh7785_io_resource, + .io_offset = 0x00000000, +}; + +static struct sh4_pci_address_map sh7780_pci_map = { + .window0 = { +#if defined(CONFIG_32BIT) + .base = SH7780_32BIT_DDR_BASE_ADDR, + .size = 0x40000000, +#else + .base = SH7780_CS0_BASE_ADDR, + .size = 0x20000000, +#endif + }, +}; -/* - * Initialization. Try all known PCI access methods. Note that we support - * using both PCI BIOS and direct access: in such cases, we use I/O ports - * to access config space. - * - * Note that the platform specific initialization (BSC registers, and memory - * space mapping) will be called via the platform defined function - * pcibios_init_platform(). - */ static int __init sh7780_pci_init(void) { + struct pci_channel *chan = &sh7780_pci_controller; unsigned int id; - int ret, match = 0; - - pr_debug("PCI: Starting intialization.\n"); - - ctrl_outl(0x00000001, SH7780_PCI_VCR2); /* Enable PCIC */ - - /* check for SH7780/SH7780R hardware */ - id = pci_read_reg(SH7780_PCIVID); - if ((id & 0xffff) == SH7780_VENDOR_ID) { - switch ((id >> 16) & 0xffff) { - case SH7763_DEVICE_ID: - case SH7780_DEVICE_ID: - case SH7781_DEVICE_ID: - case SH7785_DEVICE_ID: - match = 1; - break; - } - } + const char *type = NULL; + int ret; + u32 word; - if (unlikely(!match)) { - printk(KERN_ERR "PCI: This is not an SH7780 (%x)\n", id); + printk(KERN_NOTICE "PCI: Starting intialization.\n"); + + chan->reg_base = 0xfe040000; + + /* Enable CPU access to the PCIC registers. */ + __raw_writel(PCIECR_ENBL, PCIECR); + + id = __raw_readw(chan->reg_base + SH7780_PCIVID); + if (id != SH7780_VENDOR_ID) { + printk(KERN_ERR "PCI: Unknown vendor ID 0x%04x.\n", id); return -ENODEV; } - /* Setup the INTC */ - if (mach_is_7780se()) { - /* ICR0: IRL=use separately */ - ctrl_outl(0x00C00020, INTC_ICR0); - /* ICR1: detect low level(for 2ndcut) */ - ctrl_outl(0xAAAA0000, INTC_ICR1); - /* INTPRI: priority=3(all) */ - ctrl_outl(0x33333333, INTC_INTPRI); + id = __raw_readw(chan->reg_base + SH7780_PCIDID); + type = (id == SH7763_DEVICE_ID) ? "SH7763" : + (id == SH7780_DEVICE_ID) ? "SH7780" : + (id == SH7781_DEVICE_ID) ? "SH7781" : + (id == SH7785_DEVICE_ID) ? "SH7785" : + NULL; + if (unlikely(!type)) { + printk(KERN_ERR "PCI: Found an unsupported Renesas host " + "controller, device id 0x%04x.\n", id); + return -EINVAL; } - if ((ret = sh4_pci_check_direct()) != 0) - return ret; + printk(KERN_NOTICE "PCI: Found a Renesas %s host " + "controller, revision %d.\n", type, + __raw_readb(chan->reg_base + SH7780_PCIRID)); - return pcibios_init_platform(); -} -core_initcall(sh7780_pci_init); - -int __init sh7780_pcic_init(struct sh4_pci_address_map *map) -{ - u32 word; + if ((ret = sh4_pci_check_direct(chan)) != 0) + return ret; /* - * This code is unused for some boards as it is done in the - * bootloader and doing it here means the MAC addresses loaded - * by the bootloader get lost. - */ - if (!(map->flags & SH4_PCIC_NO_RESET)) { - /* toggle PCI reset pin */ - word = SH4_PCICR_PREFIX | SH4_PCICR_PRST; - pci_write_reg(word, SH4_PCICR); - /* Wait for a long time... not 1 sec. but long enough */ - mdelay(100); - word = SH4_PCICR_PREFIX; - pci_write_reg(word, SH4_PCICR); - } - - /* set the command/status bits to: - * Wait Cycle Control + Parity Enable + Bus Master + - * Mem space enable + * Set the class and sub-class codes. */ - pci_write_reg(0x00000046, SH7780_PCICMD); + __raw_writeb(PCI_CLASS_BRIDGE_HOST >> 8, + chan->reg_base + SH7780_PCIBCC); + __raw_writeb(PCI_CLASS_BRIDGE_HOST & 0xff, + chan->reg_base + SH7780_PCISUB); - /* define this host as the host bridge */ - word = PCI_BASE_CLASS_BRIDGE << 24; - pci_write_reg(word, SH7780_PCIRID); + pci_cache_line_size = pci_read_reg(chan, SH7780_PCICLS) / 4; - /* Set IO and Mem windows to local address + /* + * Set IO and Mem windows to local address * Make PCI and local address the same for easy 1 to 1 mapping */ - pci_write_reg(map->window0.size - 0xfffff, SH4_PCILSR0); - pci_write_reg(map->window1.size - 0xfffff, SH4_PCILSR1); + pci_write_reg(chan, sh7780_pci_map.window0.size - 0xfffff, SH4_PCILSR0); /* Set the values on window 0 PCI config registers */ - pci_write_reg(map->window0.base, SH4_PCILAR0); - pci_write_reg(map->window0.base, SH7780_PCIMBAR0); - /* Set the values on window 1 PCI config registers */ - pci_write_reg(map->window1.base, SH4_PCILAR1); - pci_write_reg(map->window1.base, SH7780_PCIMBAR1); - - /* Map IO space into PCI IO window - * The IO window is 64K-PCIBIOS_MIN_IO in size - * IO addresses will be translated to the - * PCI IO window base address - */ - pr_debug("PCI: Mapping IO address 0x%x - 0x%x to base 0x%x\n", - PCIBIOS_MIN_IO, (64 << 10), - SH7780_PCI_IO_BASE + PCIBIOS_MIN_IO); + pci_write_reg(chan, sh7780_pci_map.window0.base, SH4_PCILAR0); + pci_write_reg(chan, sh7780_pci_map.window0.base, SH7780_PCIMBAR0); - /* NOTE: I'm ignoring the PCI error IRQs for now.. - * TODO: add support for the internal error interrupts and - * DMA interrupts... - */ + pci_write_reg(chan, 0x0000380f, SH4_PCIAINTM); + + /* Set up standard PCI config registers */ + __raw_writew(0xFB00, chan->reg_base + SH7780_PCISTATUS); + __raw_writew(0x0047, chan->reg_base + SH7780_PCICMD); + __raw_writew(0x1912, chan->reg_base + SH7780_PCISVID); + __raw_writew(0x0001, chan->reg_base + SH7780_PCISID); + + __raw_writeb(0x00, chan->reg_base + SH7780_PCIPIF); /* Apply any last-minute PCIC fixups */ - pci_fixup_pcic(); + pci_fixup_pcic(chan); + + pci_write_reg(chan, 0xfd000000, SH7780_PCIMBR0); + pci_write_reg(chan, 0x00fc0000, SH7780_PCIMBMR0); + +#ifdef CONFIG_32BIT + pci_write_reg(chan, 0xc0000000, SH7780_PCIMBR2); + pci_write_reg(chan, 0x20000000 - SH7780_PCI_IO_SIZE, SH7780_PCIMBMR2); +#endif + + /* Set IOBR for windows containing area specified in pci.h */ + pci_write_reg(chan, chan->io_resource->start & ~(SH7780_PCI_IO_SIZE-1), + SH7780_PCIIOBR); + pci_write_reg(chan, ((SH7780_PCI_IO_SIZE-1) & (7<<18)), + SH7780_PCIIOBMR); /* SH7780 init done, set central function init complete */ /* use round robin mode to stop a device starving/overruning */ word = SH4_PCICR_PREFIX | SH4_PCICR_CFIN | SH4_PCICR_FTO; - pci_write_reg(word, SH4_PCICR); + pci_write_reg(chan, word, SH4_PCICR); + + __set_io_port_base(SH7780_PCI_IO_BASE); + + register_pci_controller(chan); - return 1; + return 0; } +arch_initcall(sh7780_pci_init); diff --git a/arch/sh/drivers/pci/pci-sh7780.h b/arch/sh/drivers/pci/pci-sh7780.h index 93adc7119b7..4a52478c97c 100644 --- a/arch/sh/drivers/pci/pci-sh7780.h +++ b/arch/sh/drivers/pci/pci-sh7780.h @@ -20,9 +20,8 @@ #define SH7785_DEVICE_ID 0x0007 /* SH7780 Control Registers */ -#define SH7780_PCI_VCR0 0xFE000000 -#define SH7780_PCI_VCR1 0xFE000004 -#define SH7780_PCI_VCR2 0xFE000008 +#define PCIECR 0xFE000008 +#define PCIECR_ENBL 0x01 /* SH7780 Specific Values */ #define SH7780_PCI_CONFIG_BASE 0xFD000000 /* Config space base addr */ @@ -35,7 +34,6 @@ #define SH7780_PCI_IO_SIZE 0x00400000 /* Size of IO window */ #define SH7780_PCIREG_BASE 0xFE040000 /* PCI regs base address */ -#define PCI_REG(n) (SH7780_PCIREG_BASE+n) /* SH7780 PCI Config Registers */ #define SH7780_PCIVID 0x000 /* Vendor ID */ @@ -67,11 +65,6 @@ #define SH7780_PCIPMCSR_BSE 0x046 #define SH7780_PCICDD 0x047 -#define SH7780_PCICR 0x100 /* PCI Control Register */ -#define SH7780_PCILSR 0x104 /* PCI Local Space Register0 */ -#define SH7780_PCILSR1 0x108 /* PCI Local Space Register1 */ -#define SH7780_PCILAR0 0x10C /* PCI Local Address Register1 */ -#define SH7780_PCILAR1 0x110 /* PCI Local Address Register1 */ #define SH7780_PCIIR 0x114 /* PCI Interrupt Register */ #define SH7780_PCIIMR 0x118 /* PCI Interrupt Mask Register */ #define SH7780_PCIAIR 0x11C /* Error Address Register */ @@ -106,9 +99,4 @@ #define SH7780_32BIT_DDR_BASE_ADDR 0x40000000 -struct sh4_pci_address_map; - -/* arch/sh/drivers/pci/pci-sh7780.c */ -int sh7780_pcic_init(struct sh4_pci_address_map *map); - #endif /* _PCI_SH7780_H_ */ diff --git a/arch/sh/drivers/pci/pci.c b/arch/sh/drivers/pci/pci.c index 0d6ac7a1db4..54d77cbb8b3 100644 --- a/arch/sh/drivers/pci/pci.c +++ b/arch/sh/drivers/pci/pci.c @@ -1,67 +1,156 @@ /* - * arch/sh/drivers/pci/pci.c + * New-style PCI core. * - * Copyright (c) 2002 M. R. Brown <mrbrown@linux-sh.org> - * Copyright (c) 2004 - 2006 Paul Mundt <lethal@linux-sh.org> + * Copyright (c) 2004 - 2009 Paul Mundt + * Copyright (c) 2002 M. R. Brown * - * These functions are collected here to reduce duplication of common - * code amongst the many platform-specific PCI support code files. - * - * These routines require the following board-specific routines: - * void pcibios_fixup_irqs(); - * - * See include/asm-sh/pci.h for more information. + * Modelled after arch/mips/pci/pci.c: + * Copyright (C) 2003, 04 Ralf Baechle (ralf@linux-mips.org) * * This file is subject to the terms and conditions of the GNU General Public * License. See the file "COPYING" in the main directory of this archive * for more details. */ #include <linux/kernel.h> +#include <linux/mm.h> #include <linux/pci.h> #include <linux/init.h> +#include <linux/types.h> #include <linux/dma-debug.h> -#include <asm/io.h> +#include <linux/io.h> +#include <linux/mutex.h> -static int __init pcibios_init(void) +unsigned long PCIBIOS_MIN_IO = 0x0000; +unsigned long PCIBIOS_MIN_MEM = 0; + +/* + * The PCI controller list. + */ +static struct pci_channel *hose_head, **hose_tail = &hose_head; + +static int pci_initialized; + +static void __devinit pcibios_scanbus(struct pci_channel *hose) { - struct pci_channel *p; + static int next_busno; struct pci_bus *bus; - int busno; -#ifdef CONFIG_PCI_AUTO - /* assign resources */ - busno = 0; - for (p = board_pci_channels; p->pci_ops != NULL; p++) - busno = pciauto_assign_resources(busno, p) + 1; -#endif + bus = pci_scan_bus(next_busno, hose->pci_ops, hose); + if (bus) { + next_busno = bus->subordinate + 1; + /* Don't allow 8-bit bus number overflow inside the hose - + reserve some space for bridges. */ + if (next_busno > 224) + next_busno = 0; + + pci_bus_size_bridges(bus); + pci_bus_assign_resources(bus); + pci_enable_bridges(bus); + } +} + +static DEFINE_MUTEX(pci_scan_mutex); - /* scan the buses */ - busno = 0; - for (p = board_pci_channels; p->pci_ops != NULL; p++) { - bus = pci_scan_bus(busno, p->pci_ops, p); - busno = bus->subordinate + 1; +void __devinit register_pci_controller(struct pci_channel *hose) +{ + if (request_resource(&iomem_resource, hose->mem_resource) < 0) + goto out; + if (request_resource(&ioport_resource, hose->io_resource) < 0) { + release_resource(hose->mem_resource); + goto out; } + *hose_tail = hose; + hose_tail = &hose->next; + + /* + * Do not panic here but later - this might hapen before console init. + */ + if (!hose->io_map_base) { + printk(KERN_WARNING + "registering PCI controller with io_map_base unset\n"); + } + + /* + * Scan the bus if it is register after the PCI subsystem + * initialization. + */ + if (pci_initialized) { + mutex_lock(&pci_scan_mutex); + pcibios_scanbus(hose); + mutex_unlock(&pci_scan_mutex); + } + + return; + +out: + printk(KERN_WARNING + "Skipping PCI bus scan due to resource conflict\n"); +} + +static int __init pcibios_init(void) +{ + struct pci_channel *hose; + + /* Scan all of the recorded PCI controllers. */ + for (hose = hose_head; hose; hose = hose->next) + pcibios_scanbus(hose); + pci_fixup_irqs(pci_common_swizzle, pcibios_map_platform_irq); dma_debug_add_bus(&pci_bus_type); + pci_initialized = 1; + return 0; } subsys_initcall(pcibios_init); +static void pcibios_fixup_device_resources(struct pci_dev *dev, + struct pci_bus *bus) +{ + /* Update device resources. */ + struct pci_channel *hose = bus->sysdata; + unsigned long offset = 0; + int i; + + for (i = 0; i < PCI_NUM_RESOURCES; i++) { + if (!dev->resource[i].start) + continue; + if (dev->resource[i].flags & IORESOURCE_PCI_FIXED) + continue; + if (dev->resource[i].flags & IORESOURCE_IO) + offset = hose->io_offset; + else if (dev->resource[i].flags & IORESOURCE_MEM) + offset = hose->mem_offset; + + dev->resource[i].start += offset; + dev->resource[i].end += offset; + } +} + /* * Called after each bus is probed, but before its children * are examined. */ -void __devinit __weak pcibios_fixup_bus(struct pci_bus *bus) +void __devinit pcibios_fixup_bus(struct pci_bus *bus) { - pci_read_bridge_bases(bus); -} + struct pci_dev *dev = bus->self; + struct list_head *ln; + struct pci_channel *chan = bus->sysdata; -void pcibios_align_resource(void *data, struct resource *res, - resource_size_t size, resource_size_t align) - __attribute__ ((weak)); + if (!dev) { + bus->resource[0] = chan->io_resource; + bus->resource[1] = chan->mem_resource; + } + + for (ln = bus->devices.next; ln != &bus->devices; ln = ln->next) { + dev = pci_dev_b(ln); + + if ((dev->class >> 8) != PCI_CLASS_BRIDGE_PCI) + pcibios_fixup_device_resources(dev, bus); + } +} /* * We need to avoid collisions with `mirrored' VGA ports @@ -72,14 +161,58 @@ void pcibios_align_resource(void *data, struct resource *res, void pcibios_align_resource(void *data, struct resource *res, resource_size_t size, resource_size_t align) { + struct pci_dev *dev = data; + struct pci_channel *chan = dev->sysdata; + resource_size_t start = res->start; + if (res->flags & IORESOURCE_IO) { - resource_size_t start = res->start; + if (start < PCIBIOS_MIN_IO + chan->io_resource->start) + start = PCIBIOS_MIN_IO + chan->io_resource->start; + /* + * Put everything into 0x00-0xff region modulo 0x400. + */ if (start & 0x300) { start = (start + 0x3ff) & ~0x3ff; res->start = start; } + } else if (res->flags & IORESOURCE_MEM) { + if (start < PCIBIOS_MIN_MEM + chan->mem_resource->start) + start = PCIBIOS_MIN_MEM + chan->mem_resource->start; } + + res->start = start; +} + +void pcibios_resource_to_bus(struct pci_dev *dev, struct pci_bus_region *region, + struct resource *res) +{ + struct pci_channel *hose = dev->sysdata; + unsigned long offset = 0; + + if (res->flags & IORESOURCE_IO) + offset = hose->io_offset; + else if (res->flags & IORESOURCE_MEM) + offset = hose->mem_offset; + + region->start = res->start - offset; + region->end = res->end - offset; +} + +void __devinit +pcibios_bus_to_resource(struct pci_dev *dev, struct resource *res, + struct pci_bus_region *region) +{ + struct pci_channel *hose = dev->sysdata; + unsigned long offset = 0; + + if (res->flags & IORESOURCE_IO) + offset = hose->io_offset; + else if (res->flags & IORESOURCE_MEM) + offset = hose->mem_offset; + + res->start = region->start + offset; + res->end = region->end + offset; } int pcibios_enable_device(struct pci_dev *dev, int mask) @@ -90,13 +223,21 @@ int pcibios_enable_device(struct pci_dev *dev, int mask) pci_read_config_word(dev, PCI_COMMAND, &cmd); old_cmd = cmd; - for(idx=0; idx<6; idx++) { - if (!(mask & (1 << idx))) + for (idx=0; idx < PCI_NUM_RESOURCES; idx++) { + /* Only set up the requested stuff */ + if (!(mask & (1<<idx))) continue; + r = &dev->resource[idx]; + if (!(r->flags & (IORESOURCE_IO | IORESOURCE_MEM))) + continue; + if ((idx == PCI_ROM_RESOURCE) && + (!(r->flags & IORESOURCE_ROM_ENABLE))) + continue; if (!r->start && r->end) { - printk(KERN_ERR "PCI: Device %s not available because " - "of resource collisions\n", pci_name(dev)); + printk(KERN_ERR "PCI: Device %s not available " + "because of resource collisions\n", + pci_name(dev)); return -EINVAL; } if (r->flags & IORESOURCE_IO) @@ -104,10 +245,8 @@ int pcibios_enable_device(struct pci_dev *dev, int mask) if (r->flags & IORESOURCE_MEM) cmd |= PCI_COMMAND_MEMORY; } - if (dev->resource[PCI_ROM_RESOURCE].start) - cmd |= PCI_COMMAND_MEMORY; if (cmd != old_cmd) { - printk(KERN_INFO "PCI: Enabling device %s (%04x -> %04x)\n", + printk("PCI: Enabling device %s (%04x -> %04x)\n", pci_name(dev), old_cmd, cmd); pci_write_config_word(dev, PCI_COMMAND, cmd); } @@ -140,6 +279,43 @@ void __init pcibios_update_irq(struct pci_dev *dev, int irq) pci_write_config_byte(dev, PCI_INTERRUPT_LINE, irq); } +char * __devinit pcibios_setup(char *str) +{ + return str; +} + +int pci_mmap_page_range(struct pci_dev *dev, struct vm_area_struct *vma, + enum pci_mmap_state mmap_state, int write_combine) +{ + /* + * I/O space can be accessed via normal processor loads and stores on + * this platform but for now we elect not to do this and portable + * drivers should not do this anyway. + */ + if (mmap_state == pci_mmap_io) + return -EINVAL; + + /* + * Ignore write-combine; for now only return uncached mappings. + */ + vma->vm_page_prot = pgprot_noncached(vma->vm_page_prot); + + return remap_pfn_range(vma, vma->vm_start, vma->vm_pgoff, + vma->vm_end - vma->vm_start, + vma->vm_page_prot); +} + +static void __iomem *ioport_map_pci(struct pci_dev *dev, + unsigned long port, unsigned int nr) +{ + struct pci_channel *chan = dev->sysdata; + + if (!chan->io_map_base) + chan->io_map_base = generic_io_base; + + return (void __iomem *)(chan->io_map_base + port); +} + void __iomem *pci_iomap(struct pci_dev *dev, int bar, unsigned long maxlen) { resource_size_t start = pci_resource_start(dev, bar); @@ -151,20 +327,24 @@ void __iomem *pci_iomap(struct pci_dev *dev, int bar, unsigned long maxlen) if (maxlen && len > maxlen) len = maxlen; + if (flags & IORESOURCE_IO) + return ioport_map_pci(dev, start, len); + /* * Presently the IORESOURCE_MEM case is a bit special, most * SH7751 style PCI controllers have PCI memory at a fixed - * location in the address space where no remapping is desired - * (typically at 0xfd000000, but is_pci_memaddr() will know - * best). With the IORESOURCE_MEM case more care has to be taken + * location in the address space where no remapping is desired. + * With the IORESOURCE_MEM case more care has to be taken * to inhibit page table mapping for legacy cores, but this is * punted off to __ioremap(). * -- PFM. */ - if (flags & IORESOURCE_IO) - return ioport_map(start, len); - if (flags & IORESOURCE_MEM) - return ioremap(start, len); + if (flags & IORESOURCE_MEM) { + if (flags & IORESOURCE_CACHEABLE) + return ioremap(start, len); + + return ioremap_nocache(start, len); + } return NULL; } @@ -175,3 +355,10 @@ void pci_iounmap(struct pci_dev *dev, void __iomem *addr) iounmap(addr); } EXPORT_SYMBOL(pci_iounmap); + +#ifdef CONFIG_HOTPLUG +EXPORT_SYMBOL(pcibios_resource_to_bus); +EXPORT_SYMBOL(pcibios_bus_to_resource); +EXPORT_SYMBOL(PCIBIOS_MIN_IO); +EXPORT_SYMBOL(PCIBIOS_MIN_MEM); +#endif |