diff options
Diffstat (limited to 'arch/x86_64/mm')
| -rw-r--r-- | arch/x86_64/mm/init.c | 37 | ||||
| -rw-r--r-- | arch/x86_64/mm/numa.c | 48 | ||||
| -rw-r--r-- | arch/x86_64/mm/srat.c | 170 |
3 files changed, 237 insertions, 18 deletions
diff --git a/arch/x86_64/mm/init.c b/arch/x86_64/mm/init.c index e5f7f1c3446..4ba34e95d83 100644 --- a/arch/x86_64/mm/init.c +++ b/arch/x86_64/mm/init.c @@ -305,7 +305,7 @@ static void __meminit phys_pud_init(pud_t *pud, unsigned long address, unsigned if (paddr >= end) break; - if (!after_bootmem && !e820_mapped(paddr, paddr+PUD_SIZE, 0)) { + if (!after_bootmem && !e820_any_mapped(paddr, paddr+PUD_SIZE, 0)) { set_pud(pud, __pud(0)); continue; } @@ -507,9 +507,8 @@ void __init clear_kernel_mapping(unsigned long address, unsigned long size) /* * Memory hotplug specific functions - * These are only for non-NUMA machines right now. */ -#ifdef CONFIG_MEMORY_HOTPLUG +#if defined(CONFIG_ACPI_HOTPLUG_MEMORY) || defined(CONFIG_ACPI_HOTPLUG_MEMORY_MODULE) void online_page(struct page *page) { @@ -520,6 +519,38 @@ void online_page(struct page *page) num_physpages++; } +#ifndef CONFIG_MEMORY_HOTPLUG +/* + * Memory Hotadd without sparsemem. The mem_maps have been allocated in advance, + * just online the pages. + */ +int __add_pages(struct zone *z, unsigned long start_pfn, unsigned long nr_pages) +{ + int err = -EIO; + unsigned long pfn; + unsigned long total = 0, mem = 0; + for (pfn = start_pfn; pfn < start_pfn + nr_pages; pfn++) { + if (pfn_valid(pfn)) { + online_page(pfn_to_page(pfn)); + err = 0; + mem++; + } + total++; + } + if (!err) { + z->spanned_pages += total; + z->present_pages += mem; + z->zone_pgdat->node_spanned_pages += total; + z->zone_pgdat->node_present_pages += mem; + } + return err; +} +#endif + +/* + * Memory is added always to NORMAL zone. This means you will never get + * additional DMA/DMA32 memory. + */ int add_memory(u64 start, u64 size) { struct pglist_data *pgdat = NODE_DATA(0); diff --git a/arch/x86_64/mm/numa.c b/arch/x86_64/mm/numa.c index 4be82d6e2b4..b2fac14baac 100644 --- a/arch/x86_64/mm/numa.c +++ b/arch/x86_64/mm/numa.c @@ -100,11 +100,30 @@ int early_pfn_to_nid(unsigned long pfn) } #endif +static void * __init +early_node_mem(int nodeid, unsigned long start, unsigned long end, + unsigned long size) +{ + unsigned long mem = find_e820_area(start, end, size); + void *ptr; + if (mem != -1L) + return __va(mem); + ptr = __alloc_bootmem_nopanic(size, + SMP_CACHE_BYTES, __pa(MAX_DMA_ADDRESS)); + if (ptr == 0) { + printk(KERN_ERR "Cannot find %lu bytes in node %d\n", + size, nodeid); + return NULL; + } + return ptr; +} + /* Initialize bootmem allocator for a node */ void __init setup_node_bootmem(int nodeid, unsigned long start, unsigned long end) { unsigned long start_pfn, end_pfn, bootmap_pages, bootmap_size, bootmap_start; unsigned long nodedata_phys; + void *bootmap; const int pgdat_size = round_up(sizeof(pg_data_t), PAGE_SIZE); start = round_up(start, ZONE_ALIGN); @@ -114,13 +133,11 @@ void __init setup_node_bootmem(int nodeid, unsigned long start, unsigned long en start_pfn = start >> PAGE_SHIFT; end_pfn = end >> PAGE_SHIFT; - nodedata_phys = find_e820_area(start, end, pgdat_size); - if (nodedata_phys == -1L) - panic("Cannot find memory pgdat in node %d\n", nodeid); - - Dprintk("nodedata_phys %lx\n", nodedata_phys); + node_data[nodeid] = early_node_mem(nodeid, start, end, pgdat_size); + if (node_data[nodeid] == NULL) + return; + nodedata_phys = __pa(node_data[nodeid]); - node_data[nodeid] = phys_to_virt(nodedata_phys); memset(NODE_DATA(nodeid), 0, sizeof(pg_data_t)); NODE_DATA(nodeid)->bdata = &plat_node_bdata[nodeid]; NODE_DATA(nodeid)->node_start_pfn = start_pfn; @@ -129,9 +146,15 @@ void __init setup_node_bootmem(int nodeid, unsigned long start, unsigned long en /* Find a place for the bootmem map */ bootmap_pages = bootmem_bootmap_pages(end_pfn - start_pfn); bootmap_start = round_up(nodedata_phys + pgdat_size, PAGE_SIZE); - bootmap_start = find_e820_area(bootmap_start, end, bootmap_pages<<PAGE_SHIFT); - if (bootmap_start == -1L) - panic("Not enough continuous space for bootmap on node %d", nodeid); + bootmap = early_node_mem(nodeid, bootmap_start, end, + bootmap_pages<<PAGE_SHIFT); + if (bootmap == NULL) { + if (nodedata_phys < start || nodedata_phys >= end) + free_bootmem((unsigned long)node_data[nodeid],pgdat_size); + node_data[nodeid] = NULL; + return; + } + bootmap_start = __pa(bootmap); Dprintk("bootmap start %lu pages %lu\n", bootmap_start, bootmap_pages); bootmap_size = init_bootmem_node(NODE_DATA(nodeid), @@ -142,6 +165,9 @@ void __init setup_node_bootmem(int nodeid, unsigned long start, unsigned long en reserve_bootmem_node(NODE_DATA(nodeid), nodedata_phys, pgdat_size); reserve_bootmem_node(NODE_DATA(nodeid), bootmap_start, bootmap_pages<<PAGE_SHIFT); +#ifdef CONFIG_ACPI_NUMA + srat_reserve_add_area(nodeid); +#endif node_set_online(nodeid); } @@ -162,11 +188,13 @@ void __init setup_node_zones(int nodeid) memory. */ memmapsize = sizeof(struct page) * (end_pfn-start_pfn); limit = end_pfn << PAGE_SHIFT; +#ifdef CONFIG_FLAT_NODE_MEM_MAP NODE_DATA(nodeid)->node_mem_map = __alloc_bootmem_core(NODE_DATA(nodeid)->bdata, memmapsize, SMP_CACHE_BYTES, round_down(limit - memmapsize, PAGE_SIZE), limit); +#endif size_zones(zones, holes, start_pfn, end_pfn); free_area_init_node(nodeid, NODE_DATA(nodeid), zones, @@ -335,6 +363,8 @@ __init int numa_setup(char *opt) #ifdef CONFIG_ACPI_NUMA if (!strncmp(opt,"noacpi",6)) acpi_numa = -1; + if (!strncmp(opt,"hotadd=", 7)) + hotadd_percent = simple_strtoul(opt+7, NULL, 10); #endif return 1; } diff --git a/arch/x86_64/mm/srat.c b/arch/x86_64/mm/srat.c index 2eb879590dc..15ae9fcd65a 100644 --- a/arch/x86_64/mm/srat.c +++ b/arch/x86_64/mm/srat.c @@ -15,15 +15,26 @@ #include <linux/bitmap.h> #include <linux/module.h> #include <linux/topology.h> +#include <linux/bootmem.h> +#include <linux/mm.h> #include <asm/proto.h> #include <asm/numa.h> #include <asm/e820.h> +#if (defined(CONFIG_ACPI_HOTPLUG_MEMORY) || \ + defined(CONFIG_ACPI_HOTPLUG_MEMORY_MODULE)) \ + && !defined(CONFIG_MEMORY_HOTPLUG) +#define RESERVE_HOTADD 1 +#endif + static struct acpi_table_slit *acpi_slit; static nodemask_t nodes_parsed __initdata; static nodemask_t nodes_found __initdata; static struct bootnode nodes[MAX_NUMNODES] __initdata; +static struct bootnode nodes_add[MAX_NUMNODES] __initdata; +static int found_add_area __initdata; +int hotadd_percent __initdata = 10; static u8 pxm2node[256] = { [0 ... 255] = 0xff }; /* Too small nodes confuse the VM badly. Usually they result @@ -71,6 +82,10 @@ static __init int conflicting_nodes(unsigned long start, unsigned long end) static __init void cutoff_node(int i, unsigned long start, unsigned long end) { struct bootnode *nd = &nodes[i]; + + if (found_add_area) + return; + if (nd->start < start) { nd->start = start; if (nd->end < nd->start) @@ -90,6 +105,8 @@ static __init void bad_srat(void) acpi_numa = -1; for (i = 0; i < MAX_LOCAL_APIC; i++) apicid_to_node[i] = NUMA_NO_NODE; + for (i = 0; i < MAX_NUMNODES; i++) + nodes_add[i].start = nodes[i].end = 0; } static __init inline int srat_disabled(void) @@ -155,11 +172,114 @@ acpi_numa_processor_affinity_init(struct acpi_table_processor_affinity *pa) pxm, pa->apic_id, node); } +#ifdef RESERVE_HOTADD +/* + * Protect against too large hotadd areas that would fill up memory. + */ +static int hotadd_enough_memory(struct bootnode *nd) +{ + static unsigned long allocated; + static unsigned long last_area_end; + unsigned long pages = (nd->end - nd->start) >> PAGE_SHIFT; + long mem = pages * sizeof(struct page); + unsigned long addr; + unsigned long allowed; + unsigned long oldpages = pages; + + if (mem < 0) + return 0; + allowed = (end_pfn - e820_hole_size(0, end_pfn)) * PAGE_SIZE; + allowed = (allowed / 100) * hotadd_percent; + if (allocated + mem > allowed) { + /* Give them at least part of their hotadd memory upto hotadd_percent + It would be better to spread the limit out + over multiple hotplug areas, but that is too complicated + right now */ + if (allocated >= allowed) + return 0; + pages = (allowed - allocated + mem) / sizeof(struct page); + mem = pages * sizeof(struct page); + nd->end = nd->start + pages*PAGE_SIZE; + } + /* Not completely fool proof, but a good sanity check */ + addr = find_e820_area(last_area_end, end_pfn<<PAGE_SHIFT, mem); + if (addr == -1UL) + return 0; + if (pages != oldpages) + printk(KERN_NOTICE "SRAT: Hotadd area limited to %lu bytes\n", + pages << PAGE_SHIFT); + last_area_end = addr + mem; + allocated += mem; + return 1; +} + +/* + * It is fine to add this area to the nodes data it will be used later + * This code supports one contigious hot add area per node. + */ +static int reserve_hotadd(int node, unsigned long start, unsigned long end) +{ + unsigned long s_pfn = start >> PAGE_SHIFT; + unsigned long e_pfn = end >> PAGE_SHIFT; + int changed = 0; + struct bootnode *nd = &nodes_add[node]; + + /* I had some trouble with strange memory hotadd regions breaking + the boot. Be very strict here and reject anything unexpected. + If you want working memory hotadd write correct SRATs. + + The node size check is a basic sanity check to guard against + mistakes */ + if ((signed long)(end - start) < NODE_MIN_SIZE) { + printk(KERN_ERR "SRAT: Hotplug area too small\n"); + return -1; + } + + /* This check might be a bit too strict, but I'm keeping it for now. */ + if (e820_hole_size(s_pfn, e_pfn) != e_pfn - s_pfn) { + printk(KERN_ERR "SRAT: Hotplug area has existing memory\n"); + return -1; + } + + if (!hotadd_enough_memory(&nodes_add[node])) { + printk(KERN_ERR "SRAT: Hotplug area too large\n"); + return -1; + } + + /* Looks good */ + + found_add_area = 1; + if (nd->start == nd->end) { + nd->start = start; + nd->end = end; + changed = 1; + } else { + if (nd->start == end) { + nd->start = start; + changed = 1; + } + if (nd->end == start) { + nd->end = end; + changed = 1; + } + if (!changed) + printk(KERN_ERR "SRAT: Hotplug zone not continuous. Partly ignored\n"); + } + + if ((nd->end >> PAGE_SHIFT) > end_pfn) + end_pfn = nd->end >> PAGE_SHIFT; + + if (changed) + printk(KERN_INFO "SRAT: hot plug zone found %Lx - %Lx\n", nd->start, nd->end); + return 0; +} +#endif + /* Callback for parsing of the Proximity Domain <-> Memory Area mappings */ void __init acpi_numa_memory_affinity_init(struct acpi_table_memory_affinity *ma) { - struct bootnode *nd; + struct bootnode *nd, oldnode; unsigned long start, end; int node, pxm; int i; @@ -172,6 +292,8 @@ acpi_numa_memory_affinity_init(struct acpi_table_memory_affinity *ma) } if (ma->flags.enabled == 0) return; + if (ma->flags.hot_pluggable && hotadd_percent == 0) + return; start = ma->base_addr_lo | ((u64)ma->base_addr_hi << 32); end = start + (ma->length_lo | ((u64)ma->length_hi << 32)); pxm = ma->proximity_domain; @@ -181,10 +303,6 @@ acpi_numa_memory_affinity_init(struct acpi_table_memory_affinity *ma) bad_srat(); return; } - /* It is fine to add this area to the nodes data it will be used later*/ - if (ma->flags.hot_pluggable == 1) - printk(KERN_INFO "SRAT: hot plug zone found %lx - %lx \n", - start, end); i = conflicting_nodes(start, end); if (i == node) { printk(KERN_WARNING @@ -199,6 +317,7 @@ acpi_numa_memory_affinity_init(struct acpi_table_memory_affinity *ma) return; } nd = &nodes[node]; + oldnode = *nd; if (!node_test_and_set(node, nodes_parsed)) { nd->start = start; nd->end = end; @@ -208,8 +327,19 @@ acpi_numa_memory_affinity_init(struct acpi_table_memory_affinity *ma) if (nd->end < end) nd->end = end; } + printk(KERN_INFO "SRAT: Node %u PXM %u %Lx-%Lx\n", node, pxm, nd->start, nd->end); + +#ifdef RESERVE_HOTADD + if (ma->flags.hot_pluggable && reserve_hotadd(node, start, end) < 0) { + /* Ignore hotadd region. Undo damage */ + printk(KERN_NOTICE "SRAT: Hotplug region ignored\n"); + *nd = oldnode; + if ((nd->start | nd->end) == 0) + node_clear(node, nodes_parsed); + } +#endif } /* Sanity check to catch more bad SRATs (they are amazingly common). @@ -225,6 +355,9 @@ static int nodes_cover_memory(void) unsigned long e = nodes[i].end >> PAGE_SHIFT; pxmram += e - s; pxmram -= e820_hole_size(s, e); + pxmram -= nodes_add[i].end - nodes_add[i].start; + if ((long)pxmram < 0) + pxmram = 0; } e820ram = end_pfn - e820_hole_size(0, end_pfn); @@ -258,7 +391,7 @@ int __init acpi_scan_nodes(unsigned long start, unsigned long end) /* First clean up the node list */ for (i = 0; i < MAX_NUMNODES; i++) { - cutoff_node(i, start, end); + cutoff_node(i, start, end); if ((nodes[i].end - nodes[i].start) < NODE_MIN_SIZE) unparse_node(i); } @@ -282,6 +415,12 @@ int __init acpi_scan_nodes(unsigned long start, unsigned long end) /* Finally register nodes */ for_each_node_mask(i, nodes_parsed) setup_node_bootmem(i, nodes[i].start, nodes[i].end); + /* Try again in case setup_node_bootmem missed one due + to missing bootmem */ + for_each_node_mask(i, nodes_parsed) + if (!node_online(i)) + setup_node_bootmem(i, nodes[i].start, nodes[i].end); + for (i = 0; i < NR_CPUS; i++) { if (cpu_to_node[i] == NUMA_NO_NODE) continue; @@ -303,6 +442,25 @@ static int node_to_pxm(int n) return 0; } +void __init srat_reserve_add_area(int nodeid) +{ + if (found_add_area && nodes_add[nodeid].end) { + u64 total_mb; + + printk(KERN_INFO "SRAT: Reserving hot-add memory space " + "for node %d at %Lx-%Lx\n", + nodeid, nodes_add[nodeid].start, nodes_add[nodeid].end); + total_mb = (nodes_add[nodeid].end - nodes_add[nodeid].start) + >> PAGE_SHIFT; + total_mb *= sizeof(struct page); + total_mb >>= 20; + printk(KERN_INFO "SRAT: This will cost you %Lu MB of " + "pre-allocated memory.\n", (unsigned long long)total_mb); + reserve_bootmem_node(NODE_DATA(nodeid), nodes_add[nodeid].start, + nodes_add[nodeid].end - nodes_add[nodeid].start); + } +} + int __node_distance(int a, int b) { int index; |