aboutsummaryrefslogtreecommitdiff
path: root/drivers/ata/pata_hpt37x.c
diff options
context:
space:
mode:
Diffstat (limited to 'drivers/ata/pata_hpt37x.c')
-rw-r--r--drivers/ata/pata_hpt37x.c1257
1 files changed, 1257 insertions, 0 deletions
diff --git a/drivers/ata/pata_hpt37x.c b/drivers/ata/pata_hpt37x.c
new file mode 100644
index 00000000000..7c3da53f1e0
--- /dev/null
+++ b/drivers/ata/pata_hpt37x.c
@@ -0,0 +1,1257 @@
+/*
+ * Libata driver for the highpoint 37x and 30x UDMA66 ATA controllers.
+ *
+ * This driver is heavily based upon:
+ *
+ * linux/drivers/ide/pci/hpt366.c Version 0.36 April 25, 2003
+ *
+ * Copyright (C) 1999-2003 Andre Hedrick <andre@linux-ide.org>
+ * Portions Copyright (C) 2001 Sun Microsystems, Inc.
+ * Portions Copyright (C) 2003 Red Hat Inc
+ *
+ * TODO
+ * PLL mode
+ * Look into engine reset on timeout errors. Should not be
+ * required.
+ */
+
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/pci.h>
+#include <linux/init.h>
+#include <linux/blkdev.h>
+#include <linux/delay.h>
+#include <scsi/scsi_host.h>
+#include <linux/libata.h>
+
+#define DRV_NAME "pata_hpt37x"
+#define DRV_VERSION "0.5"
+
+struct hpt_clock {
+ u8 xfer_speed;
+ u32 timing;
+};
+
+struct hpt_chip {
+ const char *name;
+ unsigned int base;
+ struct hpt_clock const *clocks[4];
+};
+
+/* key for bus clock timings
+ * bit
+ * 0:3 data_high_time. inactive time of DIOW_/DIOR_ for PIO and MW
+ * DMA. cycles = value + 1
+ * 4:8 data_low_time. active time of DIOW_/DIOR_ for PIO and MW
+ * DMA. cycles = value + 1
+ * 9:12 cmd_high_time. inactive time of DIOW_/DIOR_ during task file
+ * register access.
+ * 13:17 cmd_low_time. active time of DIOW_/DIOR_ during task file
+ * register access.
+ * 18:21 udma_cycle_time. clock freq and clock cycles for UDMA xfer.
+ * during task file register access.
+ * 22:24 pre_high_time. time to initialize 1st cycle for PIO and MW DMA
+ * xfer.
+ * 25:27 cmd_pre_high_time. time to initialize 1st PIO cycle for task
+ * register access.
+ * 28 UDMA enable
+ * 29 DMA enable
+ * 30 PIO_MST enable. if set, the chip is in bus master mode during
+ * PIO.
+ * 31 FIFO enable.
+ */
+
+/* from highpoint documentation. these are old values */
+static const struct hpt_clock hpt370_timings_33[] = {
+/* { XFER_UDMA_5, 0x1A85F442, 0x16454e31 }, */
+ { XFER_UDMA_5, 0x16454e31 },
+ { XFER_UDMA_4, 0x16454e31 },
+ { XFER_UDMA_3, 0x166d4e31 },
+ { XFER_UDMA_2, 0x16494e31 },
+ { XFER_UDMA_1, 0x164d4e31 },
+ { XFER_UDMA_0, 0x16514e31 },
+
+ { XFER_MW_DMA_2, 0x26514e21 },
+ { XFER_MW_DMA_1, 0x26514e33 },
+ { XFER_MW_DMA_0, 0x26514e97 },
+
+ { XFER_PIO_4, 0x06514e21 },
+ { XFER_PIO_3, 0x06514e22 },
+ { XFER_PIO_2, 0x06514e33 },
+ { XFER_PIO_1, 0x06914e43 },
+ { XFER_PIO_0, 0x06914e57 },
+ { 0, 0x06514e57 }
+};
+
+static const struct hpt_clock hpt370_timings_66[] = {
+ { XFER_UDMA_5, 0x14846231 },
+ { XFER_UDMA_4, 0x14886231 },
+ { XFER_UDMA_3, 0x148c6231 },
+ { XFER_UDMA_2, 0x148c6231 },
+ { XFER_UDMA_1, 0x14906231 },
+ { XFER_UDMA_0, 0x14986231 },
+
+ { XFER_MW_DMA_2, 0x26514e21 },
+ { XFER_MW_DMA_1, 0x26514e33 },
+ { XFER_MW_DMA_0, 0x26514e97 },
+
+ { XFER_PIO_4, 0x06514e21 },
+ { XFER_PIO_3, 0x06514e22 },
+ { XFER_PIO_2, 0x06514e33 },
+ { XFER_PIO_1, 0x06914e43 },
+ { XFER_PIO_0, 0x06914e57 },
+ { 0, 0x06514e57 }
+};
+
+/* these are the current (4 sep 2001) timings from highpoint */
+static const struct hpt_clock hpt370a_timings_33[] = {
+ { XFER_UDMA_5, 0x12446231 },
+ { XFER_UDMA_4, 0x12446231 },
+ { XFER_UDMA_3, 0x126c6231 },
+ { XFER_UDMA_2, 0x12486231 },
+ { XFER_UDMA_1, 0x124c6233 },
+ { XFER_UDMA_0, 0x12506297 },
+
+ { XFER_MW_DMA_2, 0x22406c31 },
+ { XFER_MW_DMA_1, 0x22406c33 },
+ { XFER_MW_DMA_0, 0x22406c97 },
+
+ { XFER_PIO_4, 0x06414e31 },
+ { XFER_PIO_3, 0x06414e42 },
+ { XFER_PIO_2, 0x06414e53 },
+ { XFER_PIO_1, 0x06814e93 },
+ { XFER_PIO_0, 0x06814ea7 },
+ { 0, 0x06814ea7 }
+};
+
+/* 2x 33MHz timings */
+static const struct hpt_clock hpt370a_timings_66[] = {
+ { XFER_UDMA_5, 0x1488e673 },
+ { XFER_UDMA_4, 0x1488e673 },
+ { XFER_UDMA_3, 0x1498e673 },
+ { XFER_UDMA_2, 0x1490e673 },
+ { XFER_UDMA_1, 0x1498e677 },
+ { XFER_UDMA_0, 0x14a0e73f },
+
+ { XFER_MW_DMA_2, 0x2480fa73 },
+ { XFER_MW_DMA_1, 0x2480fa77 },
+ { XFER_MW_DMA_0, 0x2480fb3f },
+
+ { XFER_PIO_4, 0x0c82be73 },
+ { XFER_PIO_3, 0x0c82be95 },
+ { XFER_PIO_2, 0x0c82beb7 },
+ { XFER_PIO_1, 0x0d02bf37 },
+ { XFER_PIO_0, 0x0d02bf5f },
+ { 0, 0x0d02bf5f }
+};
+
+static const struct hpt_clock hpt370a_timings_50[] = {
+ { XFER_UDMA_5, 0x12848242 },
+ { XFER_UDMA_4, 0x12ac8242 },
+ { XFER_UDMA_3, 0x128c8242 },
+ { XFER_UDMA_2, 0x120c8242 },
+ { XFER_UDMA_1, 0x12148254 },
+ { XFER_UDMA_0, 0x121882ea },
+
+ { XFER_MW_DMA_2, 0x22808242 },
+ { XFER_MW_DMA_1, 0x22808254 },
+ { XFER_MW_DMA_0, 0x228082ea },
+
+ { XFER_PIO_4, 0x0a81f442 },
+ { XFER_PIO_3, 0x0a81f443 },
+ { XFER_PIO_2, 0x0a81f454 },
+ { XFER_PIO_1, 0x0ac1f465 },
+ { XFER_PIO_0, 0x0ac1f48a },
+ { 0, 0x0ac1f48a }
+};
+
+static const struct hpt_clock hpt372_timings_33[] = {
+ { XFER_UDMA_6, 0x1c81dc62 },
+ { XFER_UDMA_5, 0x1c6ddc62 },
+ { XFER_UDMA_4, 0x1c8ddc62 },
+ { XFER_UDMA_3, 0x1c8edc62 }, /* checkme */
+ { XFER_UDMA_2, 0x1c91dc62 },
+ { XFER_UDMA_1, 0x1c9adc62 }, /* checkme */
+ { XFER_UDMA_0, 0x1c82dc62 }, /* checkme */
+
+ { XFER_MW_DMA_2, 0x2c829262 },
+ { XFER_MW_DMA_1, 0x2c829266 }, /* checkme */
+ { XFER_MW_DMA_0, 0x2c82922e }, /* checkme */
+
+ { XFER_PIO_4, 0x0c829c62 },
+ { XFER_PIO_3, 0x0c829c84 },
+ { XFER_PIO_2, 0x0c829ca6 },
+ { XFER_PIO_1, 0x0d029d26 },
+ { XFER_PIO_0, 0x0d029d5e },
+ { 0, 0x0d029d5e }
+};
+
+static const struct hpt_clock hpt372_timings_50[] = {
+ { XFER_UDMA_5, 0x12848242 },
+ { XFER_UDMA_4, 0x12ac8242 },
+ { XFER_UDMA_3, 0x128c8242 },
+ { XFER_UDMA_2, 0x120c8242 },
+ { XFER_UDMA_1, 0x12148254 },
+ { XFER_UDMA_0, 0x121882ea },
+
+ { XFER_MW_DMA_2, 0x22808242 },
+ { XFER_MW_DMA_1, 0x22808254 },
+ { XFER_MW_DMA_0, 0x228082ea },
+
+ { XFER_PIO_4, 0x0a81f442 },
+ { XFER_PIO_3, 0x0a81f443 },
+ { XFER_PIO_2, 0x0a81f454 },
+ { XFER_PIO_1, 0x0ac1f465 },
+ { XFER_PIO_0, 0x0ac1f48a },
+ { 0, 0x0a81f443 }
+};
+
+static const struct hpt_clock hpt372_timings_66[] = {
+ { XFER_UDMA_6, 0x1c869c62 },
+ { XFER_UDMA_5, 0x1cae9c62 },
+ { XFER_UDMA_4, 0x1c8a9c62 },
+ { XFER_UDMA_3, 0x1c8e9c62 },
+ { XFER_UDMA_2, 0x1c929c62 },
+ { XFER_UDMA_1, 0x1c9a9c62 },
+ { XFER_UDMA_0, 0x1c829c62 },
+
+ { XFER_MW_DMA_2, 0x2c829c62 },
+ { XFER_MW_DMA_1, 0x2c829c66 },
+ { XFER_MW_DMA_0, 0x2c829d2e },
+
+ { XFER_PIO_4, 0x0c829c62 },
+ { XFER_PIO_3, 0x0c829c84 },
+ { XFER_PIO_2, 0x0c829ca6 },
+ { XFER_PIO_1, 0x0d029d26 },
+ { XFER_PIO_0, 0x0d029d5e },
+ { 0, 0x0d029d26 }
+};
+
+static const struct hpt_clock hpt374_timings_33[] = {
+ { XFER_UDMA_6, 0x12808242 },
+ { XFER_UDMA_5, 0x12848242 },
+ { XFER_UDMA_4, 0x12ac8242 },
+ { XFER_UDMA_3, 0x128c8242 },
+ { XFER_UDMA_2, 0x120c8242 },
+ { XFER_UDMA_1, 0x12148254 },
+ { XFER_UDMA_0, 0x121882ea },
+
+ { XFER_MW_DMA_2, 0x22808242 },
+ { XFER_MW_DMA_1, 0x22808254 },
+ { XFER_MW_DMA_0, 0x228082ea },
+
+ { XFER_PIO_4, 0x0a81f442 },
+ { XFER_PIO_3, 0x0a81f443 },
+ { XFER_PIO_2, 0x0a81f454 },
+ { XFER_PIO_1, 0x0ac1f465 },
+ { XFER_PIO_0, 0x0ac1f48a },
+ { 0, 0x06814e93 }
+};
+
+static const struct hpt_chip hpt370 = {
+ "HPT370",
+ 48,
+ {
+ hpt370_timings_33,
+ NULL,
+ NULL,
+ hpt370_timings_66
+ }
+};
+
+static const struct hpt_chip hpt370a = {
+ "HPT370A",
+ 48,
+ {
+ hpt370a_timings_33,
+ NULL,
+ hpt370a_timings_50,
+ hpt370a_timings_66
+ }
+};
+
+static const struct hpt_chip hpt372 = {
+ "HPT372",
+ 55,
+ {
+ hpt372_timings_33,
+ NULL,
+ hpt372_timings_50,
+ hpt372_timings_66
+ }
+};
+
+static const struct hpt_chip hpt302 = {
+ "HPT302",
+ 66,
+ {
+ hpt372_timings_33,
+ NULL,
+ hpt372_timings_50,
+ hpt372_timings_66
+ }
+};
+
+static const struct hpt_chip hpt371 = {
+ "HPT371",
+ 66,
+ {
+ hpt372_timings_33,
+ NULL,
+ hpt372_timings_50,
+ hpt372_timings_66
+ }
+};
+
+static const struct hpt_chip hpt372a = {
+ "HPT372A",
+ 66,
+ {
+ hpt372_timings_33,
+ NULL,
+ hpt372_timings_50,
+ hpt372_timings_66
+ }
+};
+
+static const struct hpt_chip hpt374 = {
+ "HPT374",
+ 48,
+ {
+ hpt374_timings_33,
+ NULL,
+ NULL,
+ NULL
+ }
+};
+
+/**
+ * hpt37x_find_mode - reset the hpt37x bus
+ * @ap: ATA port
+ * @speed: transfer mode
+ *
+ * Return the 32bit register programming information for this channel
+ * that matches the speed provided.
+ */
+
+static u32 hpt37x_find_mode(struct ata_port *ap, int speed)
+{
+ struct hpt_clock *clocks = ap->host->private_data;
+
+ while(clocks->xfer_speed) {
+ if (clocks->xfer_speed == speed)
+ return clocks->timing;
+ clocks++;
+ }
+ BUG();
+ return 0xffffffffU; /* silence compiler warning */
+}
+
+static int hpt_dma_blacklisted(const struct ata_device *dev, char *modestr, const char *list[])
+{
+ unsigned char model_num[40];
+ char *s;
+ unsigned int len;
+ int i = 0;
+
+ ata_id_string(dev->id, model_num, ATA_ID_PROD_OFS,
+ sizeof(model_num));
+ s = &model_num[0];
+ len = strnlen(s, sizeof(model_num));
+
+ /* ATAPI specifies that empty space is blank-filled; remove blanks */
+ while ((len > 0) && (s[len - 1] == ' ')) {
+ len--;
+ s[len] = 0;
+ }
+
+ while(list[i] != NULL) {
+ if (!strncmp(list[i], s, len)) {
+ printk(KERN_WARNING DRV_NAME ": %s is not supported for %s.\n",
+ modestr, list[i]);
+ return 1;
+ }
+ i++;
+ }
+ return 0;
+}
+
+static const char *bad_ata33[] = {
+ "Maxtor 92720U8", "Maxtor 92040U6", "Maxtor 91360U4", "Maxtor 91020U3", "Maxtor 90845U3", "Maxtor 90650U2",
+ "Maxtor 91360D8", "Maxtor 91190D7", "Maxtor 91020D6", "Maxtor 90845D5", "Maxtor 90680D4", "Maxtor 90510D3", "Maxtor 90340D2",
+ "Maxtor 91152D8", "Maxtor 91008D7", "Maxtor 90845D6", "Maxtor 90840D6", "Maxtor 90720D5", "Maxtor 90648D5", "Maxtor 90576D4",
+ "Maxtor 90510D4",
+ "Maxtor 90432D3", "Maxtor 90288D2", "Maxtor 90256D2",
+ "Maxtor 91000D8", "Maxtor 90910D8", "Maxtor 90875D7", "Maxtor 90840D7", "Maxtor 90750D6", "Maxtor 90625D5", "Maxtor 90500D4",
+ "Maxtor 91728D8", "Maxtor 91512D7", "Maxtor 91303D6", "Maxtor 91080D5", "Maxtor 90845D4", "Maxtor 90680D4", "Maxtor 90648D3", "Maxtor 90432D2",
+ NULL
+};
+
+static const char *bad_ata100_5[] = {
+ "IBM-DTLA-307075",
+ "IBM-DTLA-307060",
+ "IBM-DTLA-307045",
+ "IBM-DTLA-307030",
+ "IBM-DTLA-307020",
+ "IBM-DTLA-307015",
+ "IBM-DTLA-305040",
+ "IBM-DTLA-305030",
+ "IBM-DTLA-305020",
+ "IC35L010AVER07-0",
+ "IC35L020AVER07-0",
+ "IC35L030AVER07-0",
+ "IC35L040AVER07-0",
+ "IC35L060AVER07-0",
+ "WDC AC310200R",
+ NULL
+};
+
+/**
+ * hpt370_filter - mode selection filter
+ * @ap: ATA interface
+ * @adev: ATA device
+ *
+ * Block UDMA on devices that cause trouble with this controller.
+ */
+
+static unsigned long hpt370_filter(const struct ata_port *ap, struct ata_device *adev, unsigned long mask)
+{
+ if (adev->class != ATA_DEV_ATA) {
+ if (hpt_dma_blacklisted(adev, "UDMA", bad_ata33))
+ mask &= ~ATA_MASK_UDMA;
+ if (hpt_dma_blacklisted(adev, "UDMA100", bad_ata100_5))
+ mask &= ~(0x1F << ATA_SHIFT_UDMA);
+ }
+ return ata_pci_default_filter(ap, adev, mask);
+}
+
+/**
+ * hpt370a_filter - mode selection filter
+ * @ap: ATA interface
+ * @adev: ATA device
+ *
+ * Block UDMA on devices that cause trouble with this controller.
+ */
+
+static unsigned long hpt370a_filter(const struct ata_port *ap, struct ata_device *adev, unsigned long mask)
+{
+ if (adev->class != ATA_DEV_ATA) {
+ if (hpt_dma_blacklisted(adev, "UDMA100", bad_ata100_5))
+ mask &= ~ (0x1F << ATA_SHIFT_UDMA);
+ }
+ return ata_pci_default_filter(ap, adev, mask);
+}
+
+/**
+ * hpt37x_pre_reset - reset the hpt37x bus
+ * @ap: ATA port to reset
+ *
+ * Perform the initial reset handling for the 370/372 and 374 func 0
+ */
+
+static int hpt37x_pre_reset(struct ata_port *ap)
+{
+ u8 scr2, ata66;
+ struct pci_dev *pdev = to_pci_dev(ap->host->dev);
+
+ pci_read_config_byte(pdev, 0x5B, &scr2);
+ pci_write_config_byte(pdev, 0x5B, scr2 & ~0x01);
+ /* Cable register now active */
+ pci_read_config_byte(pdev, 0x5A, &ata66);
+ /* Restore state */
+ pci_write_config_byte(pdev, 0x5B, scr2);
+
+ if (ata66 & (1 << ap->port_no))
+ ap->cbl = ATA_CBL_PATA40;
+ else
+ ap->cbl = ATA_CBL_PATA80;
+
+ /* Reset the state machine */
+ pci_write_config_byte(pdev, 0x50, 0x37);
+ pci_write_config_byte(pdev, 0x54, 0x37);
+ udelay(100);
+
+ return ata_std_prereset(ap);
+}
+
+/**
+ * hpt37x_error_handler - reset the hpt374
+ * @ap: ATA port to reset
+ *
+ * Perform probe for HPT37x, except for HPT374 channel 2
+ */
+
+static void hpt37x_error_handler(struct ata_port *ap)
+{
+ ata_bmdma_drive_eh(ap, hpt37x_pre_reset, ata_std_softreset, NULL, ata_std_postreset);
+}
+
+static int hpt374_pre_reset(struct ata_port *ap)
+{
+ u16 mcr3, mcr6;
+ u8 ata66;
+
+ struct pci_dev *pdev = to_pci_dev(ap->host->dev);
+ /* Do the extra channel work */
+ pci_read_config_word(pdev, 0x52, &mcr3);
+ pci_read_config_word(pdev, 0x56, &mcr6);
+ /* Set bit 15 of 0x52 to enable TCBLID as input
+ Set bit 15 of 0x56 to enable FCBLID as input
+ */
+ pci_write_config_word(pdev, 0x52, mcr3 | 0x8000);
+ pci_write_config_word(pdev, 0x56, mcr6 | 0x8000);
+ pci_read_config_byte(pdev, 0x5A, &ata66);
+ /* Reset TCBLID/FCBLID to output */
+ pci_write_config_word(pdev, 0x52, mcr3);
+ pci_write_config_word(pdev, 0x56, mcr6);
+
+ if (ata66 & (1 << ap->port_no))
+ ap->cbl = ATA_CBL_PATA40;
+ else
+ ap->cbl = ATA_CBL_PATA80;
+
+ /* Reset the state machine */
+ pci_write_config_byte(pdev, 0x50, 0x37);
+ pci_write_config_byte(pdev, 0x54, 0x37);
+ udelay(100);
+
+ return ata_std_prereset(ap);
+}
+
+/**
+ * hpt374_error_handler - reset the hpt374
+ * @classes:
+ *
+ * The 374 cable detect is a little different due to the extra
+ * channels. The function 0 channels work like usual but function 1
+ * is special
+ */
+
+static void hpt374_error_handler(struct ata_port *ap)
+{
+ struct pci_dev *pdev = to_pci_dev(ap->host->dev);
+
+ if (!(PCI_FUNC(pdev->devfn) & 1))
+ hpt37x_error_handler(ap);
+ else
+ ata_bmdma_drive_eh(ap, hpt374_pre_reset, ata_std_softreset, NULL, ata_std_postreset);
+}
+
+/**
+ * hpt370_set_piomode - PIO setup
+ * @ap: ATA interface
+ * @adev: device on the interface
+ *
+ * Perform PIO mode setup.
+ */
+
+static void hpt370_set_piomode(struct ata_port *ap, struct ata_device *adev)
+{
+ struct pci_dev *pdev = to_pci_dev(ap->host->dev);
+ u32 addr1, addr2;
+ u32 reg;
+ u32 mode;
+ u8 fast;
+
+ addr1 = 0x40 + 4 * (adev->devno + 2 * ap->port_no);
+ addr2 = 0x51 + 4 * ap->port_no;
+
+ /* Fast interrupt prediction disable, hold off interrupt disable */
+ pci_read_config_byte(pdev, addr2, &fast);
+ fast &= ~0x02;
+ fast |= 0x01;
+ pci_write_config_byte(pdev, addr2, fast);
+
+ pci_read_config_dword(pdev, addr1, &reg);
+ mode = hpt37x_find_mode(ap, adev->pio_mode);
+ mode &= ~0x8000000; /* No FIFO in PIO */
+ mode &= ~0x30070000; /* Leave config bits alone */
+ reg &= 0x30070000; /* Strip timing bits */
+ pci_write_config_dword(pdev, addr1, reg | mode);
+}
+
+/**
+ * hpt370_set_dmamode - DMA timing setup
+ * @ap: ATA interface
+ * @adev: Device being configured
+ *
+ * Set up the channel for MWDMA or UDMA modes. Much the same as with
+ * PIO, load the mode number and then set MWDMA or UDMA flag.
+ */
+
+static void hpt370_set_dmamode(struct ata_port *ap, struct ata_device *adev)
+{
+ struct pci_dev *pdev = to_pci_dev(ap->host->dev);
+ u32 addr1, addr2;
+ u32 reg;
+ u32 mode;
+ u8 fast;
+
+ addr1 = 0x40 + 4 * (adev->devno + 2 * ap->port_no);
+ addr2 = 0x51 + 4 * ap->port_no;
+
+ /* Fast interrupt prediction disable, hold off interrupt disable */
+ pci_read_config_byte(pdev, addr2, &fast);
+ fast &= ~0x02;
+ fast |= 0x01;
+ pci_write_config_byte(pdev, addr2, fast);
+
+ pci_read_config_dword(pdev, addr1, &reg);
+ mode = hpt37x_find_mode(ap, adev->dma_mode);
+ mode |= 0x8000000; /* FIFO in MWDMA or UDMA */
+ mode &= ~0xC0000000; /* Leave config bits alone */
+ reg &= 0xC0000000; /* Strip timing bits */
+ pci_write_config_dword(pdev, addr1, reg | mode);
+}
+
+/**
+ * hpt370_bmdma_start - DMA engine begin
+ * @qc: ATA command
+ *
+ * The 370 and 370A want us to reset the DMA engine each time we
+ * use it. The 372 and later are fine.
+ */
+
+static void hpt370_bmdma_start(struct ata_queued_cmd *qc)
+{
+ struct ata_port *ap = qc->ap;
+ struct pci_dev *pdev = to_pci_dev(ap->host->dev);
+ pci_write_config_byte(pdev, 0x50 + 4 * ap->port_no, 0x37);
+ udelay(10);
+ ata_bmdma_start(qc);
+}
+
+/**
+ * hpt370_bmdma_end - DMA engine stop
+ * @qc: ATA command
+ *
+ * Work around the HPT370 DMA engine.
+ */
+
+static void hpt370_bmdma_stop(struct ata_queued_cmd *qc)
+{
+ struct ata_port *ap = qc->ap;
+ struct pci_dev *pdev = to_pci_dev(ap->host->dev);
+ u8 dma_stat = inb(ap->ioaddr.bmdma_addr + 2);
+ u8 dma_cmd;
+ unsigned long bmdma = ap->ioaddr.bmdma_addr;
+
+ if (dma_stat & 0x01) {
+ udelay(20);
+ dma_stat = inb(bmdma + 2);
+ }
+ if (dma_stat & 0x01) {
+ /* Clear the engine */
+ pci_write_config_byte(pdev, 0x50 + 4 * ap->port_no, 0x37);
+ udelay(10);
+ /* Stop DMA */
+ dma_cmd = inb(bmdma );
+ outb(dma_cmd & 0xFE, bmdma);
+ /* Clear Error */
+ dma_stat = inb(bmdma + 2);
+ outb(dma_stat | 0x06 , bmdma + 2);
+ /* Clear the engine */
+ pci_write_config_byte(pdev, 0x50 + 4 * ap->port_no, 0x37);
+ udelay(10);
+ }
+ ata_bmdma_stop(qc);
+}
+
+/**
+ * hpt372_set_piomode - PIO setup
+ * @ap: ATA interface
+ * @adev: device on the interface
+ *
+ * Perform PIO mode setup.
+ */
+
+static void hpt372_set_piomode(struct ata_port *ap, struct ata_device *adev)
+{
+ struct pci_dev *pdev = to_pci_dev(ap->host->dev);
+ u32 addr1, addr2;
+ u32 reg;
+ u32 mode;
+ u8 fast;
+
+ addr1 = 0x40 + 4 * (adev->devno + 2 * ap->port_no);
+ addr2 = 0x51 + 4 * ap->port_no;
+
+ /* Fast interrupt prediction disable, hold off interrupt disable */
+ pci_read_config_byte(pdev, addr2, &fast);
+ fast &= ~0x07;
+ pci_write_config_byte(pdev, addr2, fast);
+
+ pci_read_config_dword(pdev, addr1, &reg);
+ mode = hpt37x_find_mode(ap, adev->pio_mode);
+
+ printk("Find mode for %d reports %X\n", adev->pio_mode, mode);
+ mode &= ~0x80000000; /* No FIFO in PIO */
+ mode &= ~0x30070000; /* Leave config bits alone */
+ reg &= 0x30070000; /* Strip timing bits */
+ pci_write_config_dword(pdev, addr1, reg | mode);
+}
+
+/**
+ * hpt372_set_dmamode - DMA timing setup
+ * @ap: ATA interface
+ * @adev: Device being configured
+ *
+ * Set up the channel for MWDMA or UDMA modes. Much the same as with
+ * PIO, load the mode number and then set MWDMA or UDMA flag.
+ */
+
+static void hpt372_set_dmamode(struct ata_port *ap, struct ata_device *adev)
+{
+ struct pci_dev *pdev = to_pci_dev(ap->host->dev);
+ u32 addr1, addr2;
+ u32 reg;
+ u32 mode;
+ u8 fast;
+
+ addr1 = 0x40 + 4 * (adev->devno + 2 * ap->port_no);
+ addr2 = 0x51 + 4 * ap->port_no;
+
+ /* Fast interrupt prediction disable, hold off interrupt disable */
+ pci_read_config_byte(pdev, addr2, &fast);
+ fast &= ~0x07;
+ pci_write_config_byte(pdev, addr2, fast);
+
+ pci_read_config_dword(pdev, addr1, &reg);
+ mode = hpt37x_find_mode(ap, adev->dma_mode);
+ printk("Find mode for DMA %d reports %X\n", adev->dma_mode, mode);
+ mode &= ~0xC0000000; /* Leave config bits alone */
+ mode |= 0x80000000; /* FIFO in MWDMA or UDMA */
+ reg &= 0xC0000000; /* Strip timing bits */
+ pci_write_config_dword(pdev, addr1, reg | mode);
+}
+
+/**
+ * hpt37x_bmdma_end - DMA engine stop
+ * @qc: ATA command
+ *
+ * Clean up after the HPT372 and later DMA engine
+ */
+
+static void hpt37x_bmdma_stop(struct ata_queued_cmd *qc)
+{
+ struct ata_port *ap = qc->ap;
+ struct pci_dev *pdev = to_pci_dev(ap->host->dev);
+ int mscreg = 0x50 + 2 * ap->port_no;
+ u8 bwsr_stat, msc_stat;
+
+ pci_read_config_byte(pdev, 0x6A, &bwsr_stat);
+ pci_read_config_byte(pdev, mscreg, &msc_stat);
+ if (bwsr_stat & (1 << ap->port_no))
+ pci_write_config_byte(pdev, mscreg, msc_stat | 0x30);
+ ata_bmdma_stop(qc);
+}
+
+
+static struct scsi_host_template hpt37x_sht = {
+ .module = THIS_MODULE,
+ .name = DRV_NAME,
+ .ioctl = ata_scsi_ioctl,
+ .queuecommand = ata_scsi_queuecmd,
+ .can_queue = ATA_DEF_QUEUE,
+ .this_id = ATA_SHT_THIS_ID,
+ .sg_tablesize = LIBATA_MAX_PRD,
+ .max_sectors = ATA_MAX_SECTORS,
+ .cmd_per_lun = ATA_SHT_CMD_PER_LUN,
+ .emulated = ATA_SHT_EMULATED,
+ .use_clustering = ATA_SHT_USE_CLUSTERING,
+ .proc_name = DRV_NAME,
+ .dma_boundary = ATA_DMA_BOUNDARY,
+ .slave_configure = ata_scsi_slave_config,
+ .bios_param = ata_std_bios_param,
+};
+
+/*
+ * Configuration for HPT370
+ */
+
+static struct ata_port_operations hpt370_port_ops = {
+ .port_disable = ata_port_disable,
+ .set_piomode = hpt370_set_piomode,
+ .set_dmamode = hpt370_set_dmamode,
+ .mode_filter = hpt370_filter,
+
+ .tf_load = ata_tf_load,
+ .tf_read = ata_tf_read,
+ .check_status = ata_check_status,
+ .exec_command = ata_exec_command,
+ .dev_select = ata_std_dev_select,
+
+ .freeze = ata_bmdma_freeze,
+ .thaw = ata_bmdma_thaw,
+ .error_handler = hpt37x_error_handler,
+ .post_internal_cmd = ata_bmdma_post_internal_cmd,
+
+ .bmdma_setup = ata_bmdma_setup,
+ .bmdma_start = hpt370_bmdma_start,
+ .bmdma_stop = hpt370_bmdma_stop,
+ .bmdma_status = ata_bmdma_status,
+
+ .qc_prep = ata_qc_prep,
+ .qc_issue = ata_qc_issue_prot,
+ .eng_timeout = ata_eng_timeout,
+ .data_xfer = ata_pio_data_xfer,
+
+ .irq_handler = ata_interrupt,
+ .irq_clear = ata_bmdma_irq_clear,
+
+ .port_start = ata_port_start,
+ .port_stop = ata_port_stop,
+ .host_stop = ata_host_stop
+};
+
+/*
+ * Configuration for HPT370A. Close to 370 but less filters
+ */
+
+static struct ata_port_operations hpt370a_port_ops = {
+ .port_disable = ata_port_disable,
+ .set_piomode = hpt370_set_piomode,
+ .set_dmamode = hpt370_set_dmamode,
+ .mode_filter = hpt370a_filter,
+
+ .tf_load = ata_tf_load,
+ .tf_read = ata_tf_read,
+ .check_status = ata_check_status,
+ .exec_command = ata_exec_command,
+ .dev_select = ata_std_dev_select,
+
+ .freeze = ata_bmdma_freeze,
+ .thaw = ata_bmdma_thaw,
+ .error_handler = hpt37x_error_handler,
+ .post_internal_cmd = ata_bmdma_post_internal_cmd,
+
+ .bmdma_setup = ata_bmdma_setup,
+ .bmdma_start = hpt370_bmdma_start,
+ .bmdma_stop = hpt370_bmdma_stop,
+ .bmdma_status = ata_bmdma_status,
+
+ .qc_prep = ata_qc_prep,
+ .qc_issue = ata_qc_issue_prot,
+ .eng_timeout = ata_eng_timeout,
+ .data_xfer = ata_pio_data_xfer,
+
+ .irq_handler = ata_interrupt,
+ .irq_clear = ata_bmdma_irq_clear,
+
+ .port_start = ata_port_start,
+ .port_stop = ata_port_stop,
+ .host_stop = ata_host_stop
+};
+
+/*
+ * Configuration for HPT372, HPT371, HPT302. Slightly different PIO
+ * and DMA mode setting functionality.
+ */
+
+static struct ata_port_operations hpt372_port_ops = {
+ .port_disable = ata_port_disable,
+ .set_piomode = hpt372_set_piomode,
+ .set_dmamode = hpt372_set_dmamode,
+ .mode_filter = ata_pci_default_filter,
+
+ .tf_load = ata_tf_load,
+ .tf_read = ata_tf_read,
+ .check_status = ata_check_status,
+ .exec_command = ata_exec_command,
+ .dev_select = ata_std_dev_select,
+
+ .freeze = ata_bmdma_freeze,
+ .thaw = ata_bmdma_thaw,
+ .error_handler = hpt37x_error_handler,
+ .post_internal_cmd = ata_bmdma_post_internal_cmd,
+
+ .bmdma_setup = ata_bmdma_setup,
+ .bmdma_start = ata_bmdma_start,
+ .bmdma_stop = hpt37x_bmdma_stop,
+ .bmdma_status = ata_bmdma_status,
+
+ .qc_prep = ata_qc_prep,
+ .qc_issue = ata_qc_issue_prot,
+ .eng_timeout = ata_eng_timeout,
+ .data_xfer = ata_pio_data_xfer,
+
+ .irq_handler = ata_interrupt,
+ .irq_clear = ata_bmdma_irq_clear,
+
+ .port_start = ata_port_start,
+ .port_stop = ata_port_stop,
+ .host_stop = ata_host_stop
+};
+
+/*
+ * Configuration for HPT374. Mode setting works like 372 and friends
+ * but we have a different cable detection procedure.
+ */
+
+static struct ata_port_operations hpt374_port_ops = {
+ .port_disable = ata_port_disable,
+ .set_piomode = hpt372_set_piomode,
+ .set_dmamode = hpt372_set_dmamode,
+ .mode_filter = ata_pci_default_filter,
+
+ .tf_load = ata_tf_load,
+ .tf_read = ata_tf_read,
+ .check_status = ata_check_status,
+ .exec_command = ata_exec_command,
+ .dev_select = ata_std_dev_select,
+
+ .freeze = ata_bmdma_freeze,
+ .thaw = ata_bmdma_thaw,
+ .error_handler = hpt374_error_handler,
+ .post_internal_cmd = ata_bmdma_post_internal_cmd,
+
+ .bmdma_setup = ata_bmdma_setup,
+ .bmdma_start = ata_bmdma_start,
+ .bmdma_stop = hpt37x_bmdma_stop,
+ .bmdma_status = ata_bmdma_status,
+
+ .qc_prep = ata_qc_prep,
+ .qc_issue = ata_qc_issue_prot,
+ .eng_timeout = ata_eng_timeout,
+ .data_xfer = ata_pio_data_xfer,
+
+ .irq_handler = ata_interrupt,
+ .irq_clear = ata_bmdma_irq_clear,
+
+ .port_start = ata_port_start,
+ .port_stop = ata_port_stop,
+ .host_stop = ata_host_stop
+};
+
+/**
+ * htp37x_clock_slot - Turn timing to PC clock entry
+ * @freq: Reported frequency timing
+ * @base: Base timing
+ *
+ * Turn the timing data intoa clock slot (0 for 33, 1 for 40, 2 for 50
+ * and 3 for 66Mhz)
+ */
+
+static int hpt37x_clock_slot(unsigned int freq, unsigned int base)
+{
+ unsigned int f = (base * freq) / 192; /* Mhz */
+ if (f < 40)
+ return 0; /* 33Mhz slot */
+ if (f < 45)
+ return 1; /* 40Mhz slot */
+ if (f < 55)
+ return 2; /* 50Mhz slot */
+ return 3; /* 60Mhz slot */
+}
+
+/**
+ * hpt37x_calibrate_dpll - Calibrate the DPLL loop
+ * @dev: PCI device
+ *
+ * Perform a calibration cycle on the HPT37x DPLL. Returns 1 if this
+ * succeeds
+ */
+
+static int hpt37x_calibrate_dpll(struct pci_dev *dev)
+{
+ u8 reg5b;
+ u32 reg5c;
+ int tries;
+
+ for(tries = 0; tries < 0x5000; tries++) {
+ udelay(50);
+ pci_read_config_byte(dev, 0x5b, &reg5b);
+ if (reg5b & 0x80) {
+ /* See if it stays set */
+ for(tries = 0; tries < 0x1000; tries ++) {
+ pci_read_config_byte(dev, 0x5b, &reg5b);
+ /* Failed ? */
+ if ((reg5b & 0x80) == 0)
+ return 0;
+ }
+ /* Turn off tuning, we have the DPLL set */
+ pci_read_config_dword(dev, 0x5c, &reg5c);
+ pci_write_config_dword(dev, 0x5c, reg5c & ~ 0x100);
+ return 1;
+ }
+ }
+ /* Never went stable */
+ return 0;
+}
+/**
+ * hpt37x_init_one - Initialise an HPT37X/302
+ * @dev: PCI device
+ * @id: Entry in match table
+ *
+ * Initialise an HPT37x device. There are some interesting complications
+ * here. Firstly the chip may report 366 and be one of several variants.
+ * Secondly all the timings depend on the clock for the chip which we must
+ * detect and look up
+ *
+ * This is the known chip mappings. It may be missing a couple of later
+ * releases.
+ *
+ * Chip version PCI Rev Notes
+ * HPT366 4 (HPT366) 0 Other driver
+ * HPT366 4 (HPT366) 1 Other driver
+ * HPT368 4 (HPT366) 2 Other driver
+ * HPT370 4 (HPT366) 3 UDMA100
+ * HPT370A 4 (HPT366) 4 UDMA100
+ * HPT372 4 (HPT366) 5 UDMA133 (1)
+ * HPT372N 4 (HPT366) 6 Other driver
+ * HPT372A 5 (HPT372) 1 UDMA133 (1)
+ * HPT372N 5 (HPT372) 2 Other driver
+ * HPT302 6 (HPT302) 1 UDMA133
+ * HPT302N 6 (HPT302) 2 Other driver
+ * HPT371 7 (HPT371) * UDMA133
+ * HPT374 8 (HPT374) * UDMA133 4 channel
+ * HPT372N 9 (HPT372N) * Other driver
+ *
+ * (1) UDMA133 support depends on the bus clock
+ */
+
+static int hpt37x_init_one(struct pci_dev *dev, const struct pci_device_id *id)
+{
+ /* HPT370 - UDMA100 */
+ static struct ata_port_info info_hpt370 = {
+ .sht = &hpt37x_sht,
+ .flags = ATA_FLAG_SLAVE_POSS|ATA_FLAG_SRST,
+ .pio_mask = 0x1f,
+ .mwdma_mask = 0x07,
+ .udma_mask = 0x3f,
+ .port_ops = &hpt370_port_ops
+ };
+ /* HPT370A - UDMA100 */
+ static struct ata_port_info info_hpt370a = {
+ .sht = &hpt37x_sht,
+ .flags = ATA_FLAG_SLAVE_POSS|ATA_FLAG_SRST,
+ .pio_mask = 0x1f,
+ .mwdma_mask = 0x07,
+ .udma_mask = 0x3f,
+ .port_ops = &hpt370a_port_ops
+ };
+ /* HPT371, 372 and friends - UDMA133 */
+ static struct ata_port_info info_hpt372 = {
+ .sht = &hpt37x_sht,
+ .flags = ATA_FLAG_SLAVE_POSS|ATA_FLAG_SRST,
+ .pio_mask = 0x1f,
+ .mwdma_mask = 0x07,
+ .udma_mask = 0x7f,
+ .port_ops = &hpt372_port_ops
+ };
+ /* HPT371, 372 and friends - UDMA100 at 50MHz clock */
+ static struct ata_port_info info_hpt372_50 = {
+ .sht = &hpt37x_sht,
+ .flags = ATA_FLAG_SLAVE_POSS|ATA_FLAG_SRST,
+ .pio_mask = 0x1f,
+ .mwdma_mask = 0x07,
+ .udma_mask = 0x3f,
+ .port_ops = &hpt372_port_ops
+ };
+ /* HPT374 - UDMA133 */
+ static struct ata_port_info info_hpt374 = {
+ .sht = &hpt37x_sht,
+ .flags = ATA_FLAG_SLAVE_POSS|ATA_FLAG_SRST,
+ .pio_mask = 0x1f,
+ .mwdma_mask = 0x07,
+ .udma_mask = 0x7f,
+ .port_ops = &hpt374_port_ops
+ };
+
+ static const int MHz[4] = { 33, 40, 50, 66 };
+
+ struct ata_port_info *port_info[2];
+ struct ata_port_info *port;
+
+ u8 irqmask;
+ u32 class_rev;
+ u32 freq;
+
+ const struct hpt_chip *chip_table;
+ int clock_slot;
+
+ pci_read_config_dword(dev, PCI_CLASS_REVISION, &class_rev);
+ class_rev &= 0xFF;
+
+ if (dev->device == PCI_DEVICE_ID_TTI_HPT366) {
+ /* May be a later chip in disguise. Check */
+ /* Older chips are in the HPT366 driver. Ignore them */
+ if (class_rev < 3)
+ return -ENODEV;
+ /* N series chips have their own driver. Ignore */
+ if (class_rev == 6)
+ return -ENODEV;
+
+ switch(class_rev) {
+ case 3:
+ port = &info_hpt370;
+ chip_table = &hpt370;
+ break;
+ case 4:
+ port = &info_hpt370a;
+ chip_table = &hpt370a;
+ break;
+ case 5:
+ port = &info_hpt372;
+ chip_table = &hpt372;
+ break;
+ default:
+ printk(KERN_ERR "pata_hpt37x: Unknown HPT366 subtype please report (%d).\n", class_rev);
+ return -ENODEV;
+ }
+ } else {
+ switch(dev->device) {
+ case PCI_DEVICE_ID_TTI_HPT372:
+ /* 372N if rev >= 2*/
+ if (class_rev >= 2)
+ return -ENODEV;
+ port = &info_hpt372;
+ chip_table = &hpt372a;
+ break;
+ case PCI_DEVICE_ID_TTI_HPT302:
+ /* 302N if rev > 1 */
+ if (class_rev > 1)
+ return -ENODEV;
+ port = &info_hpt372;
+ /* Check this */
+ chip_table = &hpt302;
+ break;
+ case PCI_DEVICE_ID_TTI_HPT371:
+ port = &info_hpt372;
+ chip_table = &hpt371;
+ break;
+ case PCI_DEVICE_ID_TTI_HPT374:
+ chip_table = &hpt374;
+ port = &info_hpt374;
+ break;
+ default:
+ printk(KERN_ERR "pata_hpt37x: PCI table is bogus please report (%d).\n", dev->device);
+ return -ENODEV;
+ }
+ }
+ /* Ok so this is a chip we support */
+
+ pci_write_config_byte(dev, PCI_CACHE_LINE_SIZE, (L1_CACHE_BYTES / 4));
+ pci_write_config_byte(dev, PCI_LATENCY_TIMER, 0x78);
+ pci_write_config_byte(dev, PCI_MIN_GNT, 0x08);
+ pci_write_config_byte(dev, PCI_MAX_LAT, 0x08);
+
+ pci_read_config_byte(dev, 0x5A, &irqmask);
+ irqmask &= ~0x10;
+ pci_write_config_byte(dev, 0x5a, irqmask);
+
+ /*
+ * default to pci clock. make sure MA15/16 are set to output
+ * to prevent drives having problems with 40-pin cables. Needed
+ * for some drives such as IBM-DTLA which will not enter ready
+ * state on reset when PDIAG is a input.
+ */
+
+ pci_write_config_byte(dev, 0x5b, 0x23);
+
+ pci_read_config_dword(dev, 0x70, &freq);
+ if ((freq >> 12) != 0xABCDE) {
+ int i;
+ u8 sr;
+ u32 total = 0;
+
+ printk(KERN_WARNING "pata_hpt37x: BIOS has not set timing clocks.\n");
+
+ /* This is the process the HPT371 BIOS is reported to use */
+ for(i = 0; i < 128; i++) {
+ pci_read_config_byte(dev, 0x78, &sr);
+ total += sr;
+ udelay(15);
+ }
+ freq = total / 128;
+ }
+ freq &= 0x1FF;
+
+ /*
+ * Turn the frequency check into a band and then find a timing
+ * table to match it.
+ */
+
+ clock_slot = hpt37x_clock_slot(freq, chip_table->base);
+ if (chip_table->clocks[clock_slot] == NULL) {
+ /*
+ * We need to try PLL mode instead
+ */
+ unsigned int f_low = (MHz[clock_slot] * chip_table->base) / 192;
+ unsigned int f_high = f_low + 2;
+ int adjust;
+
+ for(adjust = 0; adjust < 8; adjust++) {
+ if (hpt37x_calibrate_dpll(dev))
+ break;
+ /* See if it'll settle at a fractionally different clock */
+ if ((adjust & 3) == 3) {
+ f_low --;
+ f_high ++;
+ }
+ pci_write_config_dword(dev, 0x5C, (f_high << 16) | f_low);
+ }
+ if (adjust == 8) {
+ printk(KERN_WARNING "hpt37x: DPLL did not stabilize.\n");
+ return -ENODEV;
+ }
+ /* Check if this works for all cases */
+ port->private_data = (void *)hpt370_timings_66;
+
+ printk(KERN_INFO "hpt37x: Bus clock %dMHz, using DPLL.\n", MHz[clock_slot]);
+ } else {
+ port->private_data = (void *)chip_table->clocks[clock_slot];
+ /*
+ * Perform a final fixup. The 371 and 372 clock determines
+ * if UDMA133 is available.
+ */
+
+ if (clock_slot == 2 && chip_table == &hpt372) { /* 50Mhz */
+ printk(KERN_WARNING "pata_hpt37x: No UDMA133 support available with 50MHz bus clock.\n");
+ if (port == &info_hpt372)
+ port = &info_hpt372_50;
+ else BUG();
+ }
+ printk(KERN_INFO "hpt37x: %s: Bus clock %dMHz.\n", chip_table->name, MHz[clock_slot]);
+ }
+ port_info[0] = port_info[1] = port;
+ /* Now kick off ATA set up */
+ return ata_pci_init_one(dev, port_info, 2);
+}
+
+static struct pci_device_id hpt37x[] = {
+ { PCI_DEVICE(PCI_VENDOR_ID_TTI, PCI_DEVICE_ID_TTI_HPT366), },
+ { PCI_DEVICE(PCI_VENDOR_ID_TTI, PCI_DEVICE_ID_TTI_HPT371), },
+ { PCI_DEVICE(PCI_VENDOR_ID_TTI, PCI_DEVICE_ID_TTI_HPT372), },
+ { PCI_DEVICE(PCI_VENDOR_ID_TTI, PCI_DEVICE_ID_TTI_HPT374), },
+ { PCI_DEVICE(PCI_VENDOR_ID_TTI, PCI_DEVICE_ID_TTI_HPT302), },
+ { 0, },
+};
+
+static struct pci_driver hpt37x_pci_driver = {
+ .name = DRV_NAME,
+ .id_table = hpt37x,
+ .probe = hpt37x_init_one,
+ .remove = ata_pci_remove_one
+};
+
+static int __init hpt37x_init(void)
+{
+ return pci_register_driver(&hpt37x_pci_driver);
+}
+
+
+static void __exit hpt37x_exit(void)
+{
+ pci_unregister_driver(&hpt37x_pci_driver);
+}
+
+
+MODULE_AUTHOR("Alan Cox");
+MODULE_DESCRIPTION("low-level driver for the Highpoint HPT37x/30x");
+MODULE_LICENSE("GPL");
+MODULE_DEVICE_TABLE(pci, hpt37x);
+MODULE_VERSION(DRV_VERSION);
+
+module_init(hpt37x_init);
+module_exit(hpt37x_exit);