aboutsummaryrefslogtreecommitdiff
path: root/drivers/ata
diff options
context:
space:
mode:
Diffstat (limited to 'drivers/ata')
-rw-r--r--drivers/ata/sata_mv.c122
1 files changed, 63 insertions, 59 deletions
diff --git a/drivers/ata/sata_mv.c b/drivers/ata/sata_mv.c
index 842b1a15b78..4eabb737a48 100644
--- a/drivers/ata/sata_mv.c
+++ b/drivers/ata/sata_mv.c
@@ -91,9 +91,9 @@ enum {
MV_IRQ_COAL_TIME_THRESHOLD = (MV_IRQ_COAL_REG_BASE + 0xd0),
MV_SATAHC0_REG_BASE = 0x20000,
- MV_FLASH_CTL = 0x1046c,
- MV_GPIO_PORT_CTL = 0x104f0,
- MV_RESET_CFG = 0x180d8,
+ MV_FLASH_CTL_OFS = 0x1046c,
+ MV_GPIO_PORT_CTL_OFS = 0x104f0,
+ MV_RESET_CFG_OFS = 0x180d8,
MV_PCI_REG_SZ = MV_MAJOR_REG_AREA_SZ,
MV_SATAHC_REG_SZ = MV_MAJOR_REG_AREA_SZ,
@@ -147,18 +147,21 @@ enum {
/* PCI interface registers */
PCI_COMMAND_OFS = 0xc00,
+ PCI_COMMAND_MRDTRIG = (1 << 7), /* PCI Master Read Trigger */
PCI_MAIN_CMD_STS_OFS = 0xd30,
STOP_PCI_MASTER = (1 << 2),
PCI_MASTER_EMPTY = (1 << 3),
GLOB_SFT_RST = (1 << 4),
- MV_PCI_MODE = 0xd00,
+ MV_PCI_MODE_OFS = 0xd00,
+ MV_PCI_MODE_MASK = 0x30,
+
MV_PCI_EXP_ROM_BAR_CTL = 0xd2c,
MV_PCI_DISC_TIMER = 0xd04,
MV_PCI_MSI_TRIGGER = 0xc38,
MV_PCI_SERR_MASK = 0xc28,
- MV_PCI_XBAR_TMOUT = 0x1d04,
+ MV_PCI_XBAR_TMOUT_OFS = 0x1d04,
MV_PCI_ERR_LOW_ADDRESS = 0x1d40,
MV_PCI_ERR_HIGH_ADDRESS = 0x1d44,
MV_PCI_ERR_ATTRIBUTE = 0x1d48,
@@ -225,16 +228,18 @@ enum {
PHY_MODE4 = 0x314,
PHY_MODE2 = 0x330,
SATA_IFCTL_OFS = 0x344,
+ SATA_TESTCTL_OFS = 0x348,
SATA_IFSTAT_OFS = 0x34c,
VENDOR_UNIQUE_FIS_OFS = 0x35c,
- FIS_CFG_OFS = 0x360,
- FIS_CFG_SINGLE_SYNC = (1 << 16), /* SYNC on DMA activation */
+ FISCFG_OFS = 0x360,
+ FISCFG_WAIT_DEV_ERR = (1 << 8), /* wait for host on DevErr */
+ FISCFG_SINGLE_SYNC = (1 << 16), /* SYNC on DMA activation */
MV5_PHY_MODE = 0x74,
- MV5_LT_MODE = 0x30,
- MV5_PHY_CTL = 0x0C,
- SATA_INTERFACE_CFG = 0x050,
+ MV5_LTMODE_OFS = 0x30,
+ MV5_PHY_CTL_OFS = 0x0C,
+ SATA_INTERFACE_CFG_OFS = 0x050,
MV_M2_PREAMP_MASK = 0x7e0,
@@ -332,10 +337,16 @@ enum {
EDMA_CMD_OFS = 0x28, /* EDMA command register */
EDMA_EN = (1 << 0), /* enable EDMA */
EDMA_DS = (1 << 1), /* disable EDMA; self-negated */
- ATA_RST = (1 << 2), /* reset trans/link/phy */
+ EDMA_RESET = (1 << 2), /* reset eng/trans/link/phy */
+
+ EDMA_STATUS_OFS = 0x30, /* EDMA engine status */
+ EDMA_STATUS_CACHE_EMPTY = (1 << 6), /* GenIIe command cache empty */
+ EDMA_STATUS_IDLE = (1 << 7), /* GenIIe EDMA enabled/idle */
- EDMA_IORDY_TMOUT = 0x34,
- EDMA_ARB_CFG = 0x38,
+ EDMA_IORDY_TMOUT_OFS = 0x34,
+ EDMA_ARB_CFG_OFS = 0x38,
+
+ EDMA_HALTCOND_OFS = 0x60, /* GenIIe halt conditions */
GEN_II_NCQ_MAX_SECTORS = 256, /* max sects/io on Gen2 w/NCQ */
@@ -359,6 +370,7 @@ enum {
#define IS_GEN_I(hpriv) ((hpriv)->hp_flags & MV_HP_GEN_I)
#define IS_GEN_II(hpriv) ((hpriv)->hp_flags & MV_HP_GEN_II)
#define IS_GEN_IIE(hpriv) ((hpriv)->hp_flags & MV_HP_GEN_IIE)
+#define IS_PCIE(hpriv) ((hpriv)->hp_flags & MV_HP_PCIE)
#define HAS_PCI(host) (!((host)->ports[0]->flags & MV_FLAG_SOC))
#define WINDOW_CTRL(i) (0x20030 + ((i) << 4))
@@ -1059,22 +1071,22 @@ static void mv6_dev_config(struct ata_device *adev)
static void mv_config_fbs(void __iomem *port_mmio, int enable_fbs)
{
- u32 old_fcfg, new_fcfg, old_ltmode, new_ltmode;
+ u32 old_fiscfg, new_fiscfg, old_ltmode, new_ltmode;
/*
* Various bit settings required for operation
* in FIS-based switching (fbs) mode on GenIIe:
*/
- old_fcfg = readl(port_mmio + FIS_CFG_OFS);
+ old_fiscfg = readl(port_mmio + FISCFG_OFS);
old_ltmode = readl(port_mmio + LTMODE_OFS);
if (enable_fbs) {
- new_fcfg = old_fcfg | FIS_CFG_SINGLE_SYNC;
+ new_fiscfg = old_fiscfg | FISCFG_SINGLE_SYNC;
new_ltmode = old_ltmode | LTMODE_BIT8;
} else { /* disable fbs */
- new_fcfg = old_fcfg & ~FIS_CFG_SINGLE_SYNC;
+ new_fiscfg = old_fiscfg & ~FISCFG_SINGLE_SYNC;
new_ltmode = old_ltmode & ~LTMODE_BIT8;
}
- if (new_fcfg != old_fcfg)
- writelfl(new_fcfg, port_mmio + FIS_CFG_OFS);
+ if (new_fiscfg != old_fiscfg)
+ writelfl(new_fiscfg, port_mmio + FISCFG_OFS);
if (new_ltmode != old_ltmode)
writelfl(new_ltmode, port_mmio + LTMODE_OFS);
}
@@ -1894,7 +1906,7 @@ static void mv5_reset_bus(struct ata_host *host, void __iomem *mmio)
static void mv5_reset_flash(struct mv_host_priv *hpriv, void __iomem *mmio)
{
- writel(0x0fcfffff, mmio + MV_FLASH_CTL);
+ writel(0x0fcfffff, mmio + MV_FLASH_CTL_OFS);
}
static void mv5_read_preamp(struct mv_host_priv *hpriv, int idx,
@@ -1913,7 +1925,7 @@ static void mv5_enable_leds(struct mv_host_priv *hpriv, void __iomem *mmio)
{
u32 tmp;
- writel(0, mmio + MV_GPIO_PORT_CTL);
+ writel(0, mmio + MV_GPIO_PORT_CTL_OFS);
/* FIXME: handle MV_HP_ERRATA_50XXB2 errata */
@@ -1931,14 +1943,14 @@ static void mv5_phy_errata(struct mv_host_priv *hpriv, void __iomem *mmio,
int fix_apm_sq = (hpriv->hp_flags & MV_HP_ERRATA_50XXB0);
if (fix_apm_sq) {
- tmp = readl(phy_mmio + MV5_LT_MODE);
+ tmp = readl(phy_mmio + MV5_LTMODE_OFS);
tmp |= (1 << 19);
- writel(tmp, phy_mmio + MV5_LT_MODE);
+ writel(tmp, phy_mmio + MV5_LTMODE_OFS);
- tmp = readl(phy_mmio + MV5_PHY_CTL);
+ tmp = readl(phy_mmio + MV5_PHY_CTL_OFS);
tmp &= ~0x3;
tmp |= 0x1;
- writel(tmp, phy_mmio + MV5_PHY_CTL);
+ writel(tmp, phy_mmio + MV5_PHY_CTL_OFS);
}
tmp = readl(phy_mmio + MV5_PHY_MODE);
@@ -1956,11 +1968,6 @@ static void mv5_reset_hc_port(struct mv_host_priv *hpriv, void __iomem *mmio,
{
void __iomem *port_mmio = mv_port_base(mmio, port);
- /*
- * The datasheet warns against setting ATA_RST when EDMA is active
- * (but doesn't say what the problem might be). So we first try
- * to disable the EDMA engine before doing the ATA_RST operation.
- */
mv_reset_channel(hpriv, mmio, port);
ZERO(0x028); /* command */
@@ -1975,7 +1982,7 @@ static void mv5_reset_hc_port(struct mv_host_priv *hpriv, void __iomem *mmio,
ZERO(0x024); /* respq outp */
ZERO(0x020); /* respq inp */
ZERO(0x02c); /* test control */
- writel(0xbc, port_mmio + EDMA_IORDY_TMOUT);
+ writel(0xbc, port_mmio + EDMA_IORDY_TMOUT_OFS);
}
#undef ZERO
@@ -2021,13 +2028,13 @@ static void mv_reset_pci_bus(struct ata_host *host, void __iomem *mmio)
struct mv_host_priv *hpriv = host->private_data;
u32 tmp;
- tmp = readl(mmio + MV_PCI_MODE);
+ tmp = readl(mmio + MV_PCI_MODE_OFS);
tmp &= 0xff00ffff;
- writel(tmp, mmio + MV_PCI_MODE);
+ writel(tmp, mmio + MV_PCI_MODE_OFS);
ZERO(MV_PCI_DISC_TIMER);
ZERO(MV_PCI_MSI_TRIGGER);
- writel(0x000100ff, mmio + MV_PCI_XBAR_TMOUT);
+ writel(0x000100ff, mmio + MV_PCI_XBAR_TMOUT_OFS);
ZERO(PCI_HC_MAIN_IRQ_MASK_OFS);
ZERO(MV_PCI_SERR_MASK);
ZERO(hpriv->irq_cause_ofs);
@@ -2045,10 +2052,10 @@ static void mv6_reset_flash(struct mv_host_priv *hpriv, void __iomem *mmio)
mv5_reset_flash(hpriv, mmio);
- tmp = readl(mmio + MV_GPIO_PORT_CTL);
+ tmp = readl(mmio + MV_GPIO_PORT_CTL_OFS);
tmp &= 0x3;
tmp |= (1 << 5) | (1 << 6);
- writel(tmp, mmio + MV_GPIO_PORT_CTL);
+ writel(tmp, mmio + MV_GPIO_PORT_CTL_OFS);
}
/**
@@ -2121,7 +2128,7 @@ static void mv6_read_preamp(struct mv_host_priv *hpriv, int idx,
void __iomem *port_mmio;
u32 tmp;
- tmp = readl(mmio + MV_RESET_CFG);
+ tmp = readl(mmio + MV_RESET_CFG_OFS);
if ((tmp & (1 << 0)) == 0) {
hpriv->signal[idx].amps = 0x7 << 8;
hpriv->signal[idx].pre = 0x1 << 5;
@@ -2137,7 +2144,7 @@ static void mv6_read_preamp(struct mv_host_priv *hpriv, int idx,
static void mv6_enable_leds(struct mv_host_priv *hpriv, void __iomem *mmio)
{
- writel(0x00000060, mmio + MV_GPIO_PORT_CTL);
+ writel(0x00000060, mmio + MV_GPIO_PORT_CTL_OFS);
}
static void mv6_phy_errata(struct mv_host_priv *hpriv, void __iomem *mmio,
@@ -2235,11 +2242,6 @@ static void mv_soc_reset_hc_port(struct mv_host_priv *hpriv,
{
void __iomem *port_mmio = mv_port_base(mmio, port);
- /*
- * The datasheet warns against setting ATA_RST when EDMA is active
- * (but doesn't say what the problem might be). So we first try
- * to disable the EDMA engine before doing the ATA_RST operation.
- */
mv_reset_channel(hpriv, mmio, port);
ZERO(0x028); /* command */
@@ -2254,7 +2256,7 @@ static void mv_soc_reset_hc_port(struct mv_host_priv *hpriv,
ZERO(0x024); /* respq outp */
ZERO(0x020); /* respq inp */
ZERO(0x02c); /* test control */
- writel(0xbc, port_mmio + EDMA_IORDY_TMOUT);
+ writel(0xbc, port_mmio + EDMA_IORDY_TMOUT_OFS);
}
#undef ZERO
@@ -2297,38 +2299,39 @@ static void mv_soc_reset_bus(struct ata_host *host, void __iomem *mmio)
return;
}
-static void mv_setup_ifctl(void __iomem *port_mmio, int want_gen2i)
+static void mv_setup_ifcfg(void __iomem *port_mmio, int want_gen2i)
{
- u32 ifctl = readl(port_mmio + SATA_INTERFACE_CFG);
+ u32 ifcfg = readl(port_mmio + SATA_INTERFACE_CFG_OFS);
- ifctl = (ifctl & 0xf7f) | 0x9b1000; /* from chip spec */
+ ifcfg = (ifcfg & 0xf7f) | 0x9b1000; /* from chip spec */
if (want_gen2i)
- ifctl |= (1 << 7); /* enable gen2i speed */
- writelfl(ifctl, port_mmio + SATA_INTERFACE_CFG);
+ ifcfg |= (1 << 7); /* enable gen2i speed */
+ writelfl(ifcfg, port_mmio + SATA_INTERFACE_CFG_OFS);
}
-/*
- * Caller must ensure that EDMA is not active,
- * by first doing mv_stop_edma() where needed.
- */
static void mv_reset_channel(struct mv_host_priv *hpriv, void __iomem *mmio,
unsigned int port_no)
{
void __iomem *port_mmio = mv_port_base(mmio, port_no);
+ /*
+ * The datasheet warns against setting EDMA_RESET when EDMA is active
+ * (but doesn't say what the problem might be). So we first try
+ * to disable the EDMA engine before doing the EDMA_RESET operation.
+ */
mv_stop_edma_engine(port_mmio);
- writelfl(ATA_RST, port_mmio + EDMA_CMD_OFS);
+ writelfl(EDMA_RESET, port_mmio + EDMA_CMD_OFS);
if (!IS_GEN_I(hpriv)) {
- /* Enable 3.0gb/s link speed */
- mv_setup_ifctl(port_mmio, 1);
+ /* Enable 3.0gb/s link speed: this survives EDMA_RESET */
+ mv_setup_ifcfg(port_mmio, 1);
}
/*
- * Strobing ATA_RST here causes a hard reset of the SATA transport,
+ * Strobing EDMA_RESET here causes a hard reset of the SATA transport,
* link, and physical layers. It resets all SATA interface registers
* (except for SATA_INTERFACE_CFG), and issues a COMRESET to the dev.
*/
- writelfl(ATA_RST, port_mmio + EDMA_CMD_OFS);
+ writelfl(EDMA_RESET, port_mmio + EDMA_CMD_OFS);
udelay(25); /* allow reset propagation */
writelfl(0, port_mmio + EDMA_CMD_OFS);
@@ -2392,7 +2395,7 @@ static int mv_hardreset(struct ata_link *link, unsigned int *class,
sata_scr_read(link, SCR_STATUS, &sstatus);
if (!IS_GEN_I(hpriv) && ++attempts >= 5 && sstatus == 0x121) {
/* Force 1.5gb/s link speed and try again */
- mv_setup_ifctl(mv_ap_base(ap), 0);
+ mv_setup_ifcfg(mv_ap_base(ap), 0);
if (time_after(jiffies + HZ, deadline))
extra = HZ; /* only extend it once, max */
}
@@ -2590,6 +2593,7 @@ static int mv_chip_id(struct ata_host *host, unsigned int board_idx)
" and avoid the final two gigabytes on"
" all RocketRAID BIOS initialized drives.\n");
}
+ /* drop through */
case chip_6042:
hpriv->ops = &mv6xxx_ops;
hp_flags |= MV_HP_GEN_IIE;
generated by cgit v1.2.3 (git 2.25.1) at 2024-12-28 06:09:54 +0000