1 files changed, 122 insertions, 340 deletions

diff --git a/drivers/i2c/chips/max6875.c b/drivers/i2c/chips/max6875.c
index 0230375f72e..9e1aeb69abf 100644
--- a/drivers/i2c/chips/max6875.c
+++ b/drivers/i2c/chips/max6875.c
@@ -5,97 +5,60 @@
 
     Based on i2c/chips/eeprom.c
 
-    The MAX6875 has two EEPROM sections: config and user.
-    At reset, the config EEPROM is read into the registers.
+    The MAX6875 has a bank of registers and two banks of EEPROM.
+    Address ranges are defined as follows:
+     * 0x0000 - 0x0046 = configuration registers
+     * 0x8000 - 0x8046 = configuration EEPROM
+     * 0x8100 - 0x82FF = user EEPROM
 
-    This driver make 3 binary files available in sysfs:
-      reg_config    - direct access to the registers
-      eeprom_config - acesses configuration eeprom space
-      eeprom_user   - free for application use
+    This driver makes the user EEPROM available for read.
 
-    In our application, we put device serial & model numbers in user eeprom.
+    The registers & config EEPROM should be accessed via i2c-dev.
 
-    Notes:
-      1) The datasheet says that register 0x44 / EEPROM 0x8044 should NOT
-         be overwritten, so the driver explicitly prevents that.
-      2) It's a good idea to keep the config (0x45) locked in config EEPROM.
-         You can temporarily enable config writes by changing register 0x45.
+    The MAX6875 ignores the lowest address bit, so each chip responds to
+    two addresses - 0x50/0x51 and 0x52/0x53.
+
+    Note that the MAX6875 uses i2c_smbus_write_byte_data() to set the read
+    address, so this driver is destructive if loaded for the wrong EEPROM chip.
 
     This program is free software; you can redistribute it and/or modify
     it under the terms of the GNU General Public License as published by
     the Free Software Foundation; version 2 of the License.
 */
 
-#include <linux/config.h>
 #include <linux/kernel.h>
 #include <linux/init.h>
 #include <linux/module.h>
 #include <linux/slab.h>
-#include <linux/sched.h>
-#include <linux/delay.h>
 #include <linux/i2c.h>
-#include <linux/i2c-sensor.h>
+#include <asm/semaphore.h>
 
-/* Addresses to scan */
-/* No address scanned by default, as this could corrupt standard EEPROMS. */
+/* Do not scan - the MAX6875 access method will write to some EEPROM chips */
 static unsigned short normal_i2c[] = {I2C_CLIENT_END};
-static unsigned int normal_isa[] = {I2C_CLIENT_ISA_END};
 
 /* Insmod parameters */
-SENSORS_INSMOD_1(max6875);
-
-/* this param will prevent 'accidental' writes to the eeprom */
-static int allow_write = 0;
-module_param(allow_write, int, 0);
-MODULE_PARM_DESC(allow_write,
-		 "Enable write access:\n"
-		 "*0: Read only\n"
-		 " 1: Read/Write access");
+I2C_CLIENT_INSMOD_1(max6875);
 
 /* The MAX6875 can only read/write 16 bytes at a time */
 #define SLICE_SIZE			16
 #define SLICE_BITS			4
 
-/* CONFIG EEPROM is at addresses 0x8000 - 0x8045, registers are at 0 - 0x45 */
-#define CONFIG_EEPROM_BASE		0x8000
-#define CONFIG_EEPROM_SIZE		0x0046
-#define CONFIG_EEPROM_SLICES		5
-
 /* USER EEPROM is at addresses 0x8100 - 0x82FF */
 #define USER_EEPROM_BASE		0x8100
 #define USER_EEPROM_SIZE		0x0200
 #define USER_EEPROM_SLICES		32
 
 /* MAX6875 commands */
-#define MAX6875_CMD_BLOCK_WRITE		0x83
-#define MAX6875_CMD_BLOCK_READ		0x84
-#define MAX6875_CMD_REBOOT		0x88
-
-enum max6875_area_type {
-	max6875_register_config=0,
-	max6875_eeprom_config,
-	max6875_eeprom_user,
-	max6857_max
-};
-
-struct eeprom_block {
-	enum max6875_area_type	type;
-	u8			slices;
-	u32			size;
-	u32			valid;
-	u32			base;
-	unsigned long		*updated;
-	u8			*data;
-};
+#define MAX6875_CMD_BLK_READ		0x84
 
 /* Each client has this additional data */
 struct max6875_data {
 	struct i2c_client	client;
 	struct semaphore	update_lock;
-	struct eeprom_block	blocks[max6857_max];
-	/* the above structs point into the arrays below */
-	u8 data[USER_EEPROM_SIZE + (CONFIG_EEPROM_SIZE*2)];
-	unsigned long last_updated[USER_EEPROM_SLICES + (CONFIG_EEPROM_SLICES*2)];
+
+	u32			valid;
+	u8			data[USER_EEPROM_SIZE];
+	unsigned long		last_updated[USER_EEPROM_SLICES];
 };
 
 static int max6875_attach_adapter(struct i2c_adapter *adapter);
@@ -111,337 +74,160 @@ static struct i2c_driver max6875_driver = {
 	.detach_client	= max6875_detach_client,
 };
 
-static int max6875_update_slice(struct i2c_client *client,
-				struct eeprom_block *blk,
-				int slice)
+static void max6875_update_slice(struct i2c_client *client, int slice)
 {
 	struct max6875_data *data = i2c_get_clientdata(client);
-	int i, j, addr, count;
-	u8 rdbuf[SLICE_SIZE];
-	int retval = 0;
+	int i, j, addr;
+	u8 *buf;
 
-	if (slice >= blk->slices)
-		return -1;
+	if (slice >= USER_EEPROM_SLICES)
+		return;
 
 	down(&data->update_lock);
 
-	if (!(blk->valid & (1 << slice)) ||
-	    (jiffies - blk->updated[slice] > 300 * HZ) ||
-	    (jiffies < blk->updated[slice])) {
-		dev_dbg(&client->dev, "Starting eeprom update, slice %u, base %u\n",
-			slice, blk->base);
+	buf = &data->data[slice << SLICE_BITS];
 
-		addr = blk->base + (slice << SLICE_BITS);
-		count = blk->size - (slice << SLICE_BITS);
-		if (count > SLICE_SIZE) {
-			count = SLICE_SIZE;
-		}
+	if (!(data->valid & (1 << slice)) ||
+	    time_after(jiffies, data->last_updated[slice])) {
 
-		/* Preset the read address */
-		if (addr < 0x100) {
-			/* select the register */
-			if (i2c_smbus_write_byte(client, addr & 0xFF)) {
-				dev_dbg(&client->dev, "max6875 register select has failed!\n");
-				retval = -1;
-				goto exit;
-			}
-		} else {
-			/* select the eeprom */
-			if (i2c_smbus_write_byte_data(client, addr >> 8, addr & 0xFF)) {
-				dev_dbg(&client->dev, "max6875 address set has failed!\n");
-				retval = -1;
-				goto exit;
-			}
+		dev_dbg(&client->dev, "Starting update of slice %u\n", slice);
+
+		data->valid &= ~(1 << slice);
+
+		addr = USER_EEPROM_BASE + (slice << SLICE_BITS);
+
+		/* select the eeprom address */
+		if (i2c_smbus_write_byte_data(client, addr >> 8, addr & 0xFF)) {
+			dev_err(&client->dev, "address set failed\n");
+			goto exit_up;
 		}
 
-		if (i2c_check_functionality(client->adapter, I2C_FUNC_SMBUS_READ_I2C_BLOCK)) {
-			if (i2c_smbus_read_i2c_block_data(client, MAX6875_CMD_BLOCK_READ,
-							  rdbuf) != SLICE_SIZE)
-			{
-				retval = -1;
-				goto exit;
+		if (i2c_check_functionality(client->adapter,
+					    I2C_FUNC_SMBUS_READ_I2C_BLOCK)) {
+			if (i2c_smbus_read_i2c_block_data(client,
+							  MAX6875_CMD_BLK_READ,
+							  buf) != SLICE_SIZE) {
+				goto exit_up;
 			}
-
-			memcpy(&blk->data[slice << SLICE_BITS], rdbuf, count);
 		} else {
-			for (i = 0; i < count; i++) {
+			for (i = 0; i < SLICE_SIZE; i++) {
 				j = i2c_smbus_read_byte(client);
-				if (j < 0)
-				{
-					retval = -1;
-					goto exit;
+				if (j < 0) {
+					goto exit_up;
 				}
-				blk->data[(slice << SLICE_BITS) + i] = (u8) j;
+				buf[i] = j;
 			}
 		}
-		blk->updated[slice] = jiffies;
-		blk->valid |= (1 << slice);
+		data->last_updated[slice] = jiffies;
+		data->valid |= (1 << slice);
 	}
-	exit:
+exit_up:
 	up(&data->update_lock);
-	return retval;
 }
 
-static ssize_t max6875_read(struct kobject *kobj, char *buf, loff_t off, size_t count,
-			    enum max6875_area_type area_type)
+static ssize_t max6875_read(struct kobject *kobj, char *buf, loff_t off,
+			    size_t count)
 {
-	struct i2c_client *client = to_i2c_client(container_of(kobj, struct device, kobj));
+	struct i2c_client *client = kobj_to_i2c_client(kobj);
 	struct max6875_data *data = i2c_get_clientdata(client);
-	struct eeprom_block *blk;
-	int slice;
-
-	blk = &data->blocks[area_type];
+	int slice, max_slice;
 
-	if (off > blk->size)
+	if (off > USER_EEPROM_SIZE)
 		return 0;
-	if (off + count > blk->size)
-		count = blk->size - off;
 
-	/* Only refresh slices which contain requested bytes */
-	for (slice = (off >> SLICE_BITS); slice <= ((off + count - 1) >> SLICE_BITS); slice++)
-		max6875_update_slice(client, blk, slice);
+	if (off + count > USER_EEPROM_SIZE)
+		count = USER_EEPROM_SIZE - off;
 
-	memcpy(buf, &blk->data[off], count);
+	/* refresh slices which contain requested bytes */
+	max_slice = (off + count - 1) >> SLICE_BITS;
+	for (slice = (off >> SLICE_BITS); slice <= max_slice; slice++)
+		max6875_update_slice(client, slice);
 
-	return count;
-}
-
-static ssize_t max6875_user_read(struct kobject *kobj, char *buf, loff_t off, size_t count)
-{
-	return max6875_read(kobj, buf, off, count, max6875_eeprom_user);
-}
-
-static ssize_t max6875_config_read(struct kobject *kobj, char *buf, loff_t off, size_t count)
-{
-	return max6875_read(kobj, buf, off, count, max6875_eeprom_config);
-}
-
-static ssize_t max6875_cfgreg_read(struct kobject *kobj, char *buf, loff_t off, size_t count)
-{
-	return max6875_read(kobj, buf, off, count, max6875_register_config);
-}
-
-
-static ssize_t max6875_write(struct kobject *kobj, char *buf, loff_t off, size_t count,
-			     enum max6875_area_type area_type)
-{
-	struct i2c_client *client = to_i2c_client(container_of(kobj, struct device, kobj));
-	struct max6875_data *data = i2c_get_clientdata(client);
-	struct eeprom_block *blk;
-	int slice, addr, retval;
-	ssize_t sent = 0;
-
-	blk = &data->blocks[area_type];
-
-	if (off > blk->size)
-		return 0;
-	if ((off + count) > blk->size)
-		count = blk->size - off;
-
-	if (down_interruptible(&data->update_lock))
-		return -EAGAIN;
-
-	/* writing to a register is done with i2c_smbus_write_byte_data() */
-	if (blk->type == max6875_register_config) {
-		for (sent = 0; sent < count; sent++) {
-			addr = off + sent;
-			if (addr == 0x44)
-				continue;
-
-			retval = i2c_smbus_write_byte_data(client, addr, buf[sent]);
-		}
-	} else {
-		int cmd, val;
-
-		/* We are writing to EEPROM */
-		for (sent = 0; sent < count; sent++) {
-			addr = blk->base + off + sent;
-			cmd = addr >> 8;
-			val = (addr & 0xff) | (buf[sent] << 8);	// reversed
-
-			if (addr == 0x8044)
-				continue;
-
-			retval = i2c_smbus_write_word_data(client, cmd, val);
-
-			if (retval) {
-				goto error_exit;
-			}
+	memcpy(buf, &data->data[off], count);
 
-			/* A write takes up to 11 ms */
-			msleep(11);
-		}
-	}
-
-	/* Invalidate the scratch buffer */
-	for (slice = (off >> SLICE_BITS); slice <= ((off + count - 1) >> SLICE_BITS); slice++)
-		blk->valid &= ~(1 << slice);
-
-	error_exit:
-	up(&data->update_lock);
-
-	return sent;
-}
-
-static ssize_t max6875_user_write(struct kobject *kobj, char *buf, loff_t off, size_t count)
-{
-	return max6875_write(kobj, buf, off, count, max6875_eeprom_user);
-}
-
-static ssize_t max6875_config_write(struct kobject *kobj, char *buf, loff_t off, size_t count)
-{
-	return max6875_write(kobj, buf, off, count, max6875_eeprom_config);
-}
-
-static ssize_t max6875_cfgreg_write(struct kobject *kobj, char *buf, loff_t off, size_t count)
-{
-	return max6875_write(kobj, buf, off, count, max6875_register_config);
+	return count;
 }
 
 static struct bin_attribute user_eeprom_attr = {
 	.attr = {
-		.name = "eeprom_user",
-		.mode = S_IRUGO | S_IWUSR | S_IWGRP,
-		.owner = THIS_MODULE,
-	},
-	.size  = USER_EEPROM_SIZE,
-	.read  = max6875_user_read,
-	.write = max6875_user_write,
-};
-
-static struct bin_attribute config_eeprom_attr = {
-	.attr = {
-		.name = "eeprom_config",
-		.mode = S_IRUGO | S_IWUSR,
-		.owner = THIS_MODULE,
-	},
-	.size  = CONFIG_EEPROM_SIZE,
-	.read  = max6875_config_read,
-	.write = max6875_config_write,
-};
-
-static struct bin_attribute config_register_attr = {
-	.attr = {
-		.name = "reg_config",
-		.mode = S_IRUGO | S_IWUSR,
+		.name = "eeprom",
+		.mode = S_IRUGO,
 		.owner = THIS_MODULE,
 	},
-	.size  = CONFIG_EEPROM_SIZE,
-	.read  = max6875_cfgreg_read,
-	.write = max6875_cfgreg_write,
+	.size = USER_EEPROM_SIZE,
+	.read = max6875_read,
 };
 
 static int max6875_attach_adapter(struct i2c_adapter *adapter)
 {
-	return i2c_detect(adapter, &addr_data, max6875_detect);
+	return i2c_probe(adapter, &addr_data, max6875_detect);
 }
 
-/* This function is called by i2c_detect */
+/* This function is called by i2c_probe */
 static int max6875_detect(struct i2c_adapter *adapter, int address, int kind)
 {
-	struct i2c_client *new_client;
+	struct i2c_client *real_client;
+	struct i2c_client *fake_client;
 	struct max6875_data *data;
 	int err = 0;
 
-	/* Prevent 24RF08 corruption (in case of user error) */
-	if (kind < 0)
-		i2c_smbus_xfer(adapter, address, 0, 0, 0,
-			       I2C_SMBUS_QUICK, NULL);
-
-	/* There are three ways we can read the EEPROM data:
-	   (1) I2C block reads (faster, but unsupported by most adapters)
-	   (2) Consecutive byte reads (100% overhead)
-	   (3) Regular byte data reads (200% overhead)
-	   The third method is not implemented by this driver because all
-	   known adapters support at least the second. */
-	if (!i2c_check_functionality(adapter, I2C_FUNC_SMBUS_READ_BYTE_DATA |
-				     I2C_FUNC_SMBUS_BYTE |
-				     I2C_FUNC_SMBUS_WRITE_BYTE_DATA))
-		goto exit;
-
-	/* OK. For now, we presume we have a valid client. We now create the
-	   client structure, even though we cannot fill it completely yet.
-	   But it allows us to access eeprom_{read,write}_value. */
-	if (!(data = kmalloc(sizeof(struct max6875_data), GFP_KERNEL))) {
-		err = -ENOMEM;
-		goto exit;
-	}
+	if (!i2c_check_functionality(adapter, I2C_FUNC_SMBUS_WRITE_BYTE_DATA
+				     | I2C_FUNC_SMBUS_READ_BYTE))
+		return 0;
+
+	/* Only check even addresses */
+	if (address & 1)
+		return 0;
+
+	if (!(data = kmalloc(sizeof(struct max6875_data), GFP_KERNEL)))
+		return -ENOMEM;
 	memset(data, 0, sizeof(struct max6875_data));
 
-	new_client = &data->client;
-	i2c_set_clientdata(new_client, data);
-	new_client->addr = address;
-	new_client->adapter = adapter;
-	new_client->driver = &max6875_driver;
-	new_client->flags = 0;
-
-	/* Setup the user section */
-	data->blocks[max6875_eeprom_user].type    = max6875_eeprom_user;
-	data->blocks[max6875_eeprom_user].slices  = USER_EEPROM_SLICES;
-	data->blocks[max6875_eeprom_user].size    = USER_EEPROM_SIZE;
-	data->blocks[max6875_eeprom_user].base    = USER_EEPROM_BASE;
-	data->blocks[max6875_eeprom_user].data    = data->data;
-	data->blocks[max6875_eeprom_user].updated = data->last_updated;
-
-	/* Setup the config section */
-	data->blocks[max6875_eeprom_config].type    = max6875_eeprom_config;
-	data->blocks[max6875_eeprom_config].slices  = CONFIG_EEPROM_SLICES;
-	data->blocks[max6875_eeprom_config].size    = CONFIG_EEPROM_SIZE;
-	data->blocks[max6875_eeprom_config].base    = CONFIG_EEPROM_BASE;
-	data->blocks[max6875_eeprom_config].data    = &data->data[USER_EEPROM_SIZE];
-	data->blocks[max6875_eeprom_config].updated = &data->last_updated[USER_EEPROM_SLICES];
-
-	/* Setup the register section */
-	data->blocks[max6875_register_config].type    = max6875_register_config;
-	data->blocks[max6875_register_config].slices  = CONFIG_EEPROM_SLICES;
-	data->blocks[max6875_register_config].size    = CONFIG_EEPROM_SIZE;
-	data->blocks[max6875_register_config].base    = 0;
-	data->blocks[max6875_register_config].data    = &data->data[USER_EEPROM_SIZE+CONFIG_EEPROM_SIZE];
-	data->blocks[max6875_register_config].updated = &data->last_updated[USER_EEPROM_SLICES+CONFIG_EEPROM_SLICES];
-
-	/* Init the data */
-	memset(data->data, 0xff, sizeof(data->data));
-
-	/* Fill in the remaining client fields */
-	strlcpy(new_client->name, "max6875", I2C_NAME_SIZE);
+	/* A fake client is created on the odd address */
+	if (!(fake_client = kmalloc(sizeof(struct i2c_client), GFP_KERNEL))) {
+		err = -ENOMEM;
+		goto exit_kfree1;
+	}
+	memset(fake_client, 0, sizeof(struct i2c_client));
+
+	/* Init real i2c_client */
+	real_client = &data->client;
+	i2c_set_clientdata(real_client, data);
+	real_client->addr = address;
+	real_client->adapter = adapter;
+	real_client->driver = &max6875_driver;
+	real_client->flags = 0;
+	strlcpy(real_client->name, "max6875", I2C_NAME_SIZE);
 	init_MUTEX(&data->update_lock);
 
-	/* Verify that the chip is really what we think it is */
-	if ((max6875_update_slice(new_client, &data->blocks[max6875_eeprom_config], 4) < 0) ||
-	    (max6875_update_slice(new_client, &data->blocks[max6875_register_config], 4) < 0))
-		goto exit_kfree;
-
-	/* 0x41,0x42 must be zero and 0x40 must match in eeprom and registers */
-	if ((data->blocks[max6875_eeprom_config].data[0x41] != 0) ||
-	    (data->blocks[max6875_eeprom_config].data[0x42] != 0) ||
-	    (data->blocks[max6875_register_config].data[0x41] != 0) ||
-	    (data->blocks[max6875_register_config].data[0x42] != 0) ||
-	    (data->blocks[max6875_eeprom_config].data[0x40] !=
-	     data->blocks[max6875_register_config].data[0x40]))
-		goto exit_kfree;
-
-	/* Tell the I2C layer a new client has arrived */
-	if ((err = i2c_attach_client(new_client)))
-		goto exit_kfree;
-
-	/* create the sysfs eeprom files with the correct permissions */
-	if (allow_write == 0) {
-		user_eeprom_attr.attr.mode &= ~S_IWUGO;
-		user_eeprom_attr.write = NULL;
-		config_eeprom_attr.attr.mode &= ~S_IWUGO;
-		config_eeprom_attr.write = NULL;
-		config_register_attr.attr.mode &= ~S_IWUGO;
-		config_register_attr.write = NULL;
-	}
-	sysfs_create_bin_file(&new_client->dev.kobj, &user_eeprom_attr);
-	sysfs_create_bin_file(&new_client->dev.kobj, &config_eeprom_attr);
-	sysfs_create_bin_file(&new_client->dev.kobj, &config_register_attr);
+	/* Init fake client data */
+	/* set the client data to the i2c_client so that it will get freed */
+	i2c_set_clientdata(fake_client, fake_client);
+	fake_client->addr = address | 1;
+	fake_client->adapter = adapter;
+	fake_client->driver = &max6875_driver;
+	fake_client->flags = 0;
+	strlcpy(fake_client->name, "max6875 subclient", I2C_NAME_SIZE);
+
+	/* Prevent 24RF08 corruption (in case of user error) */
+	i2c_smbus_write_quick(real_client, 0);
+
+	if ((err = i2c_attach_client(real_client)) != 0)
+		goto exit_kfree2;
+
+	if ((err = i2c_attach_client(fake_client)) != 0)
+		goto exit_detach;
+
+	sysfs_create_bin_file(&real_client->dev.kobj, &user_eeprom_attr);
 
 	return 0;
 
-exit_kfree:
+exit_detach:
+	i2c_detach_client(real_client);
+exit_kfree2:
+	kfree(fake_client);
+exit_kfree1:
 	kfree(data);
-exit:
 	return err;
 }
 
@@ -450,13 +236,9 @@ static int max6875_detach_client(struct i2c_client *client)
 	int err;
 
 	err = i2c_detach_client(client);
-	if (err) {
-		dev_err(&client->dev, "Client deregistration failed, client not detached.\n");
+	if (err)
 		return err;
-	}
-
 	kfree(i2c_get_clientdata(client));
-
 	return 0;
 }