aboutsummaryrefslogtreecommitdiff
path: root/drivers/net/e1000e/es2lan.c
diff options
context:
space:
mode:
Diffstat (limited to 'drivers/net/e1000e/es2lan.c')
-rw-r--r--drivers/net/e1000e/es2lan.c266
1 files changed, 172 insertions, 94 deletions
diff --git a/drivers/net/e1000e/es2lan.c b/drivers/net/e1000e/es2lan.c
index 88657adf965..dc552d7d6fa 100644
--- a/drivers/net/e1000e/es2lan.c
+++ b/drivers/net/e1000e/es2lan.c
@@ -1,7 +1,7 @@
/*******************************************************************************
Intel PRO/1000 Linux driver
- Copyright(c) 1999 - 2007 Intel Corporation.
+ Copyright(c) 1999 - 2008 Intel Corporation.
This program is free software; you can redistribute it and/or modify it
under the terms and conditions of the GNU General Public License,
@@ -41,6 +41,7 @@
#define E1000_KMRNCTRLSTA_OFFSET_FIFO_CTRL 0x00
#define E1000_KMRNCTRLSTA_OFFSET_INB_CTRL 0x02
#define E1000_KMRNCTRLSTA_OFFSET_HD_CTRL 0x10
+#define E1000_KMRNCTRLSTA_OFFSET_MAC2PHY_OPMODE 0x1F
#define E1000_KMRNCTRLSTA_FIFO_CTRL_RX_BYPASS 0x0008
#define E1000_KMRNCTRLSTA_FIFO_CTRL_TX_BYPASS 0x0800
@@ -48,6 +49,7 @@
#define E1000_KMRNCTRLSTA_HD_CTRL_10_100_DEFAULT 0x0004
#define E1000_KMRNCTRLSTA_HD_CTRL_1000_DEFAULT 0x0000
+#define E1000_KMRNCTRLSTA_OPMODE_E_IDLE 0x2000
#define E1000_TCTL_EXT_GCEX_MASK 0x000FFC00 /* Gigabit Carry Extend Padding */
#define DEFAULT_TCTL_EXT_GCEX_80003ES2LAN 0x00010000
@@ -85,6 +87,9 @@
/* Kumeran Mode Control Register (Page 193, Register 16) */
#define GG82563_KMCR_PASS_FALSE_CARRIER 0x0800
+/* Max number of times Kumeran read/write should be validated */
+#define GG82563_MAX_KMRN_RETRY 0x5
+
/* Power Management Control Register (Page 193, Register 20) */
#define GG82563_PMCR_ENABLE_ELECTRICAL_IDLE 0x0001
/* 1=Enable SERDES Electrical Idle */
@@ -92,7 +97,8 @@
/* In-Band Control Register (Page 194, Register 18) */
#define GG82563_ICR_DIS_PADDING 0x0010 /* Disable Padding */
-/* A table for the GG82563 cable length where the range is defined
+/*
+ * A table for the GG82563 cable length where the range is defined
* with a lower bound at "index" and the upper bound at
* "index + 5".
*/
@@ -118,7 +124,7 @@ static s32 e1000_init_phy_params_80003es2lan(struct e1000_hw *hw)
struct e1000_phy_info *phy = &hw->phy;
s32 ret_val;
- if (hw->media_type != e1000_media_type_copper) {
+ if (hw->phy.media_type != e1000_media_type_copper) {
phy->type = e1000_phy_none;
return 0;
}
@@ -167,15 +173,20 @@ static s32 e1000_init_nvm_params_80003es2lan(struct e1000_hw *hw)
break;
}
- nvm->type = e1000_nvm_eeprom_spi;
+ nvm->type = e1000_nvm_eeprom_spi;
size = (u16)((eecd & E1000_EECD_SIZE_EX_MASK) >>
E1000_EECD_SIZE_EX_SHIFT);
- /* Added to a constant, "size" becomes the left-shift value
+ /*
+ * Added to a constant, "size" becomes the left-shift value
* for setting word_size.
*/
size += NVM_WORD_SIZE_BASE_SHIFT;
+
+ /* EEPROM access above 16k is unsupported */
+ if (size > 14)
+ size = 14;
nvm->word_size = 1 << size;
return 0;
@@ -196,10 +207,10 @@ static s32 e1000_init_mac_params_80003es2lan(struct e1000_adapter *adapter)
/* Set media type */
switch (adapter->pdev->device) {
case E1000_DEV_ID_80003ES2LAN_SERDES_DPT:
- hw->media_type = e1000_media_type_internal_serdes;
+ hw->phy.media_type = e1000_media_type_internal_serdes;
break;
default:
- hw->media_type = e1000_media_type_copper;
+ hw->phy.media_type = e1000_media_type_copper;
break;
}
@@ -208,11 +219,10 @@ static s32 e1000_init_mac_params_80003es2lan(struct e1000_adapter *adapter)
/* Set rar entry count */
mac->rar_entry_count = E1000_RAR_ENTRIES;
/* Set if manageability features are enabled. */
- mac->arc_subsystem_valid =
- (er32(FWSM) & E1000_FWSM_MODE_MASK) ? 1 : 0;
+ mac->arc_subsystem_valid = (er32(FWSM) & E1000_FWSM_MODE_MASK) ? 1 : 0;
/* check for link */
- switch (hw->media_type) {
+ switch (hw->phy.media_type) {
case e1000_media_type_copper:
func->setup_physical_interface = e1000_setup_copper_link_80003es2lan;
func->check_for_link = e1000e_check_for_copper_link;
@@ -233,7 +243,7 @@ static s32 e1000_init_mac_params_80003es2lan(struct e1000_adapter *adapter)
return 0;
}
-static s32 e1000_get_invariants_80003es2lan(struct e1000_adapter *adapter)
+static s32 e1000_get_variants_80003es2lan(struct e1000_adapter *adapter)
{
struct e1000_hw *hw = &adapter->hw;
s32 rc;
@@ -265,6 +275,7 @@ static s32 e1000_acquire_phy_80003es2lan(struct e1000_hw *hw)
u16 mask;
mask = hw->bus.func ? E1000_SWFW_PHY1_SM : E1000_SWFW_PHY0_SM;
+ mask |= E1000_SWFW_CSR_SM;
return e1000_acquire_swfw_sync_80003es2lan(hw, mask);
}
@@ -281,6 +292,8 @@ static void e1000_release_phy_80003es2lan(struct e1000_hw *hw)
u16 mask;
mask = hw->bus.func ? E1000_SWFW_PHY1_SM : E1000_SWFW_PHY0_SM;
+ mask |= E1000_SWFW_CSR_SM;
+
e1000_release_swfw_sync_80003es2lan(hw, mask);
}
@@ -344,8 +357,10 @@ static s32 e1000_acquire_swfw_sync_80003es2lan(struct e1000_hw *hw, u16 mask)
if (!(swfw_sync & (fwmask | swmask)))
break;
- /* Firmware currently using resource (fwmask)
- * or other software thread using resource (swmask) */
+ /*
+ * Firmware currently using resource (fwmask)
+ * or other software thread using resource (swmask)
+ */
e1000e_put_hw_semaphore(hw);
mdelay(5);
i++;
@@ -403,41 +418,51 @@ static s32 e1000_read_phy_reg_gg82563_80003es2lan(struct e1000_hw *hw,
u32 page_select;
u16 temp;
+ ret_val = e1000_acquire_phy_80003es2lan(hw);
+ if (ret_val)
+ return ret_val;
+
/* Select Configuration Page */
- if ((offset & MAX_PHY_REG_ADDRESS) < GG82563_MIN_ALT_REG)
+ if ((offset & MAX_PHY_REG_ADDRESS) < GG82563_MIN_ALT_REG) {
page_select = GG82563_PHY_PAGE_SELECT;
- else
- /* Use Alternative Page Select register to access
+ } else {
+ /*
+ * Use Alternative Page Select register to access
* registers 30 and 31
*/
page_select = GG82563_PHY_PAGE_SELECT_ALT;
+ }
temp = (u16)((u16)offset >> GG82563_PAGE_SHIFT);
- ret_val = e1000e_write_phy_reg_m88(hw, page_select, temp);
- if (ret_val)
+ ret_val = e1000e_write_phy_reg_mdic(hw, page_select, temp);
+ if (ret_val) {
+ e1000_release_phy_80003es2lan(hw);
return ret_val;
+ }
- /* The "ready" bit in the MDIC register may be incorrectly set
+ /*
+ * The "ready" bit in the MDIC register may be incorrectly set
* before the device has completed the "Page Select" MDI
* transaction. So we wait 200us after each MDI command...
*/
udelay(200);
/* ...and verify the command was successful. */
- ret_val = e1000e_read_phy_reg_m88(hw, page_select, &temp);
+ ret_val = e1000e_read_phy_reg_mdic(hw, page_select, &temp);
if (((u16)offset >> GG82563_PAGE_SHIFT) != temp) {
ret_val = -E1000_ERR_PHY;
+ e1000_release_phy_80003es2lan(hw);
return ret_val;
}
udelay(200);
- ret_val = e1000e_read_phy_reg_m88(hw,
- MAX_PHY_REG_ADDRESS & offset,
- data);
+ ret_val = e1000e_read_phy_reg_mdic(hw, MAX_PHY_REG_ADDRESS & offset,
+ data);
udelay(200);
+ e1000_release_phy_80003es2lan(hw);
return ret_val;
}
@@ -458,40 +483,51 @@ static s32 e1000_write_phy_reg_gg82563_80003es2lan(struct e1000_hw *hw,
u32 page_select;
u16 temp;
+ ret_val = e1000_acquire_phy_80003es2lan(hw);
+ if (ret_val)
+ return ret_val;
+
/* Select Configuration Page */
- if ((offset & MAX_PHY_REG_ADDRESS) < GG82563_MIN_ALT_REG)
+ if ((offset & MAX_PHY_REG_ADDRESS) < GG82563_MIN_ALT_REG) {
page_select = GG82563_PHY_PAGE_SELECT;
- else
- /* Use Alternative Page Select register to access
+ } else {
+ /*
+ * Use Alternative Page Select register to access
* registers 30 and 31
*/
page_select = GG82563_PHY_PAGE_SELECT_ALT;
+ }
temp = (u16)((u16)offset >> GG82563_PAGE_SHIFT);
- ret_val = e1000e_write_phy_reg_m88(hw, page_select, temp);
- if (ret_val)
+ ret_val = e1000e_write_phy_reg_mdic(hw, page_select, temp);
+ if (ret_val) {
+ e1000_release_phy_80003es2lan(hw);
return ret_val;
+ }
- /* The "ready" bit in the MDIC register may be incorrectly set
+ /*
+ * The "ready" bit in the MDIC register may be incorrectly set
* before the device has completed the "Page Select" MDI
* transaction. So we wait 200us after each MDI command...
*/
udelay(200);
/* ...and verify the command was successful. */
- ret_val = e1000e_read_phy_reg_m88(hw, page_select, &temp);
+ ret_val = e1000e_read_phy_reg_mdic(hw, page_select, &temp);
- if (((u16)offset >> GG82563_PAGE_SHIFT) != temp)
+ if (((u16)offset >> GG82563_PAGE_SHIFT) != temp) {
+ e1000_release_phy_80003es2lan(hw);
return -E1000_ERR_PHY;
+ }
udelay(200);
- ret_val = e1000e_write_phy_reg_m88(hw,
- MAX_PHY_REG_ADDRESS & offset,
- data);
+ ret_val = e1000e_write_phy_reg_mdic(hw, MAX_PHY_REG_ADDRESS & offset,
+ data);
udelay(200);
+ e1000_release_phy_80003es2lan(hw);
return ret_val;
}
@@ -554,7 +590,8 @@ static s32 e1000_phy_force_speed_duplex_80003es2lan(struct e1000_hw *hw)
u16 phy_data;
bool link;
- /* Clear Auto-Crossover to force MDI manually. M88E1000 requires MDI
+ /*
+ * Clear Auto-Crossover to force MDI manually. M88E1000 requires MDI
* forced whenever speed and duplex are forced.
*/
ret_val = e1e_rphy(hw, M88E1000_PHY_SPEC_CTRL, &phy_data);
@@ -583,7 +620,7 @@ static s32 e1000_phy_force_speed_duplex_80003es2lan(struct e1000_hw *hw)
udelay(1);
- if (hw->phy.wait_for_link) {
+ if (hw->phy.autoneg_wait_to_complete) {
hw_dbg(hw, "Waiting for forced speed/duplex link "
"on GG82563 phy.\n");
@@ -593,7 +630,8 @@ static s32 e1000_phy_force_speed_duplex_80003es2lan(struct e1000_hw *hw)
return ret_val;
if (!link) {
- /* We didn't get link.
+ /*
+ * We didn't get link.
* Reset the DSP and cross our fingers.
*/
ret_val = e1000e_phy_reset_dsp(hw);
@@ -612,7 +650,8 @@ static s32 e1000_phy_force_speed_duplex_80003es2lan(struct e1000_hw *hw)
if (ret_val)
return ret_val;
- /* Resetting the phy means we need to verify the TX_CLK corresponds
+ /*
+ * Resetting the phy means we need to verify the TX_CLK corresponds
* to the link speed. 10Mbps -> 2.5MHz, else 25MHz.
*/
phy_data &= ~GG82563_MSCR_TX_CLK_MASK;
@@ -621,7 +660,8 @@ static s32 e1000_phy_force_speed_duplex_80003es2lan(struct e1000_hw *hw)
else
phy_data |= GG82563_MSCR_TX_CLK_100MBPS_25;
- /* In addition, we must re-enable CRS on Tx for both half and full
+ /*
+ * In addition, we must re-enable CRS on Tx for both half and full
* duplex.
*/
phy_data |= GG82563_MSCR_ASSERT_CRS_ON_TX;
@@ -671,7 +711,7 @@ static s32 e1000_get_link_up_info_80003es2lan(struct e1000_hw *hw, u16 *speed,
{
s32 ret_val;
- if (hw->media_type == e1000_media_type_copper) {
+ if (hw->phy.media_type == e1000_media_type_copper) {
ret_val = e1000e_get_speed_and_duplex_copper(hw,
speed,
duplex);
@@ -704,7 +744,8 @@ static s32 e1000_reset_hw_80003es2lan(struct e1000_hw *hw)
u32 icr;
s32 ret_val;
- /* Prevent the PCI-E bus from sticking if there is no TLP connection
+ /*
+ * Prevent the PCI-E bus from sticking if there is no TLP connection
* on the last TLP read/write transaction when MAC is reset.
*/
ret_val = e1000e_disable_pcie_master(hw);
@@ -776,16 +817,16 @@ static s32 e1000_init_hw_80003es2lan(struct e1000_hw *hw)
ret_val = e1000e_setup_link(hw);
/* Set the transmit descriptor write-back policy */
- reg_data = er32(TXDCTL);
+ reg_data = er32(TXDCTL(0));
reg_data = (reg_data & ~E1000_TXDCTL_WTHRESH) |
E1000_TXDCTL_FULL_TX_DESC_WB | E1000_TXDCTL_COUNT_DESC;
- ew32(TXDCTL, reg_data);
+ ew32(TXDCTL(0), reg_data);
/* ...for both queues. */
- reg_data = er32(TXDCTL1);
+ reg_data = er32(TXDCTL(1));
reg_data = (reg_data & ~E1000_TXDCTL_WTHRESH) |
E1000_TXDCTL_FULL_TX_DESC_WB | E1000_TXDCTL_COUNT_DESC;
- ew32(TXDCTL1, reg_data);
+ ew32(TXDCTL(1), reg_data);
/* Enable retransmit on late collisions */
reg_data = er32(TCTL);
@@ -808,7 +849,8 @@ static s32 e1000_init_hw_80003es2lan(struct e1000_hw *hw)
reg_data &= ~0x00100000;
E1000_WRITE_REG_ARRAY(hw, E1000_FFLT, 0x0001, reg_data);
- /* Clear all of the statistics registers (clear on read). It is
+ /*
+ * Clear all of the statistics registers (clear on read). It is
* important that we do this after we have tried to establish link
* because the symbol error count will increment wildly if there
* is no link.
@@ -829,29 +871,29 @@ static void e1000_initialize_hw_bits_80003es2lan(struct e1000_hw *hw)
u32 reg;
/* Transmit Descriptor Control 0 */
- reg = er32(TXDCTL);
+ reg = er32(TXDCTL(0));
reg |= (1 << 22);
- ew32(TXDCTL, reg);
+ ew32(TXDCTL(0), reg);
/* Transmit Descriptor Control 1 */
- reg = er32(TXDCTL1);
+ reg = er32(TXDCTL(1));
reg |= (1 << 22);
- ew32(TXDCTL1, reg);
+ ew32(TXDCTL(1), reg);
/* Transmit Arbitration Control 0 */
- reg = er32(TARC0);
+ reg = er32(TARC(0));
reg &= ~(0xF << 27); /* 30:27 */
- if (hw->media_type != e1000_media_type_copper)
+ if (hw->phy.media_type != e1000_media_type_copper)
reg &= ~(1 << 20);
- ew32(TARC0, reg);
+ ew32(TARC(0), reg);
/* Transmit Arbitration Control 1 */
- reg = er32(TARC1);
+ reg = er32(TARC(1));
if (er32(TCTL) & E1000_TCTL_MULR)
reg &= ~(1 << 28);
else
reg |= (1 << 28);
- ew32(TARC1, reg);
+ ew32(TARC(1), reg);
}
/**
@@ -865,10 +907,10 @@ static s32 e1000_copper_link_setup_gg82563_80003es2lan(struct e1000_hw *hw)
struct e1000_phy_info *phy = &hw->phy;
s32 ret_val;
u32 ctrl_ext;
- u16 data;
+ u32 i = 0;
+ u16 data, data2;
- ret_val = e1e_rphy(hw, GG82563_PHY_MAC_SPEC_CTRL,
- &data);
+ ret_val = e1e_rphy(hw, GG82563_PHY_MAC_SPEC_CTRL, &data);
if (ret_val)
return ret_val;
@@ -876,12 +918,12 @@ static s32 e1000_copper_link_setup_gg82563_80003es2lan(struct e1000_hw *hw)
/* Use 25MHz for both link down and 1000Base-T for Tx clock. */
data |= GG82563_MSCR_TX_CLK_1000MBPS_25;
- ret_val = e1e_wphy(hw, GG82563_PHY_MAC_SPEC_CTRL,
- data);
+ ret_val = e1e_wphy(hw, GG82563_PHY_MAC_SPEC_CTRL, data);
if (ret_val)
return ret_val;
- /* Options:
+ /*
+ * Options:
* MDI/MDI-X = 0 (default)
* 0 - Auto for all speeds
* 1 - MDI mode
@@ -907,7 +949,8 @@ static s32 e1000_copper_link_setup_gg82563_80003es2lan(struct e1000_hw *hw)
break;
}
- /* Options:
+ /*
+ * Options:
* disable_polarity_correction = 0 (default)
* Automatic Correction for Reversed Cable Polarity
* 0 - Disabled
@@ -928,14 +971,25 @@ static s32 e1000_copper_link_setup_gg82563_80003es2lan(struct e1000_hw *hw)
return ret_val;
}
- /* Bypass RX and TX FIFO's */
- ret_val = e1000e_write_kmrn_reg(hw,
- E1000_KMRNCTRLSTA_OFFSET_FIFO_CTRL,
- E1000_KMRNCTRLSTA_FIFO_CTRL_RX_BYPASS |
+ /* Bypass Rx and Tx FIFO's */
+ ret_val = e1000e_write_kmrn_reg(hw, E1000_KMRNCTRLSTA_OFFSET_FIFO_CTRL,
+ E1000_KMRNCTRLSTA_FIFO_CTRL_RX_BYPASS |
E1000_KMRNCTRLSTA_FIFO_CTRL_TX_BYPASS);
if (ret_val)
return ret_val;
+ ret_val = e1000e_read_kmrn_reg(hw,
+ E1000_KMRNCTRLSTA_OFFSET_MAC2PHY_OPMODE,
+ &data);
+ if (ret_val)
+ return ret_val;
+ data |= E1000_KMRNCTRLSTA_OPMODE_E_IDLE;
+ ret_val = e1000e_write_kmrn_reg(hw,
+ E1000_KMRNCTRLSTA_OFFSET_MAC2PHY_OPMODE,
+ data);
+ if (ret_val)
+ return ret_val;
+
ret_val = e1e_rphy(hw, GG82563_PHY_SPEC_CTRL_2, &data);
if (ret_val)
return ret_val;
@@ -953,7 +1007,8 @@ static s32 e1000_copper_link_setup_gg82563_80003es2lan(struct e1000_hw *hw)
if (ret_val)
return ret_val;
- /* Do not init these registers when the HW is in IAMT mode, since the
+ /*
+ * Do not init these registers when the HW is in IAMT mode, since the
* firmware will have already initialized them. We only initialize
* them if the HW is not in IAMT mode.
*/
@@ -964,9 +1019,18 @@ static s32 e1000_copper_link_setup_gg82563_80003es2lan(struct e1000_hw *hw)
if (ret_val)
return ret_val;
- ret_val = e1e_rphy(hw, GG82563_PHY_KMRN_MODE_CTRL, &data);
- if (ret_val)
- return ret_val;
+ do {
+ ret_val = e1e_rphy(hw, GG82563_PHY_KMRN_MODE_CTRL,
+ &data);
+ if (ret_val)
+ return ret_val;
+
+ ret_val = e1e_rphy(hw, GG82563_PHY_KMRN_MODE_CTRL,
+ &data2);
+ if (ret_val)
+ return ret_val;
+ i++;
+ } while ((data != data2) && (i < GG82563_MAX_KMRN_RETRY));
data &= ~GG82563_KMCR_PASS_FALSE_CARRIER;
ret_val = e1e_wphy(hw, GG82563_PHY_KMRN_MODE_CTRL, data);
@@ -974,7 +1038,8 @@ static s32 e1000_copper_link_setup_gg82563_80003es2lan(struct e1000_hw *hw)
return ret_val;
}
- /* Workaround: Disable padding in Kumeran interface in the MAC
+ /*
+ * Workaround: Disable padding in Kumeran interface in the MAC
* and in the PHY to avoid CRC errors.
*/
ret_val = e1e_rphy(hw, GG82563_PHY_INBAND_CTRL, &data);
@@ -1007,9 +1072,11 @@ static s32 e1000_setup_copper_link_80003es2lan(struct e1000_hw *hw)
ctrl &= ~(E1000_CTRL_FRCSPD | E1000_CTRL_FRCDPX);
ew32(CTRL, ctrl);
- /* Set the mac to wait the maximum time between each
+ /*
+ * Set the mac to wait the maximum time between each
* iteration and increase the max iterations when
- * polling the phy; this fixes erroneous timeouts at 10Mbps. */
+ * polling the phy; this fixes erroneous timeouts at 10Mbps.
+ */
ret_val = e1000e_write_kmrn_reg(hw, GG82563_REG(0x34, 4), 0xFFFF);
if (ret_val)
return ret_val;
@@ -1026,9 +1093,8 @@ static s32 e1000_setup_copper_link_80003es2lan(struct e1000_hw *hw)
if (ret_val)
return ret_val;
reg_data |= E1000_KMRNCTRLSTA_INB_CTRL_DIS_PADDING;
- ret_val = e1000e_write_kmrn_reg(hw,
- E1000_KMRNCTRLSTA_OFFSET_INB_CTRL,
- reg_data);
+ ret_val = e1000e_write_kmrn_reg(hw, E1000_KMRNCTRLSTA_OFFSET_INB_CTRL,
+ reg_data);
if (ret_val)
return ret_val;
@@ -1053,12 +1119,12 @@ static s32 e1000_cfg_kmrn_10_100_80003es2lan(struct e1000_hw *hw, u16 duplex)
{
s32 ret_val;
u32 tipg;
- u16 reg_data;
+ u32 i = 0;
+ u16 reg_data, reg_data2;
reg_data = E1000_KMRNCTRLSTA_HD_CTRL_10_100_DEFAULT;
- ret_val = e1000e_write_kmrn_reg(hw,
- E1000_KMRNCTRLSTA_OFFSET_HD_CTRL,
- reg_data);
+ ret_val = e1000e_write_kmrn_reg(hw, E1000_KMRNCTRLSTA_OFFSET_HD_CTRL,
+ reg_data);
if (ret_val)
return ret_val;
@@ -1068,9 +1134,16 @@ static s32 e1000_cfg_kmrn_10_100_80003es2lan(struct e1000_hw *hw, u16 duplex)
tipg |= DEFAULT_TIPG_IPGT_10_100_80003ES2LAN;
ew32(TIPG, tipg);
- ret_val = e1e_rphy(hw, GG82563_PHY_KMRN_MODE_CTRL, &reg_data);
- if (ret_val)
- return ret_val;
+ do {
+ ret_val = e1e_rphy(hw, GG82563_PHY_KMRN_MODE_CTRL, &reg_data);
+ if (ret_val)
+ return ret_val;
+
+ ret_val = e1e_rphy(hw, GG82563_PHY_KMRN_MODE_CTRL, &reg_data2);
+ if (ret_val)
+ return ret_val;
+ i++;
+ } while ((reg_data != reg_data2) && (i < GG82563_MAX_KMRN_RETRY));
if (duplex == HALF_DUPLEX)
reg_data |= GG82563_KMCR_PASS_FALSE_CARRIER;
@@ -1092,13 +1165,13 @@ static s32 e1000_cfg_kmrn_10_100_80003es2lan(struct e1000_hw *hw, u16 duplex)
static s32 e1000_cfg_kmrn_1000_80003es2lan(struct e1000_hw *hw)
{
s32 ret_val;
- u16 reg_data;
+ u16 reg_data, reg_data2;
u32 tipg;
+ u32 i = 0;
reg_data = E1000_KMRNCTRLSTA_HD_CTRL_1000_DEFAULT;
- ret_val = e1000e_write_kmrn_reg(hw,
- E1000_KMRNCTRLSTA_OFFSET_HD_CTRL,
- reg_data);
+ ret_val = e1000e_write_kmrn_reg(hw, E1000_KMRNCTRLSTA_OFFSET_HD_CTRL,
+ reg_data);
if (ret_val)
return ret_val;
@@ -1108,9 +1181,16 @@ static s32 e1000_cfg_kmrn_1000_80003es2lan(struct e1000_hw *hw)
tipg |= DEFAULT_TIPG_IPGT_1000_80003ES2LAN;
ew32(TIPG, tipg);
- ret_val = e1e_rphy(hw, GG82563_PHY_KMRN_MODE_CTRL, &reg_data);
- if (ret_val)
- return ret_val;
+ do {
+ ret_val = e1e_rphy(hw, GG82563_PHY_KMRN_MODE_CTRL, &reg_data);
+ if (ret_val)
+ return ret_val;
+
+ ret_val = e1e_rphy(hw, GG82563_PHY_KMRN_MODE_CTRL, &reg_data2);
+ if (ret_val)
+ return ret_val;
+ i++;
+ } while ((reg_data != reg_data2) && (i < GG82563_MAX_KMRN_RETRY));
reg_data &= ~GG82563_KMCR_PASS_FALSE_CARRIER;
ret_val = e1e_wphy(hw, GG82563_PHY_KMRN_MODE_CTRL, reg_data);
@@ -1175,7 +1255,7 @@ static struct e1000_mac_operations es2_mac_ops = {
.get_link_up_info = e1000_get_link_up_info_80003es2lan,
.led_on = e1000e_led_on_generic,
.led_off = e1000e_led_off_generic,
- .mc_addr_list_update = e1000e_mc_addr_list_update_generic,
+ .update_mc_addr_list = e1000e_update_mc_addr_list_generic,
.reset_hw = e1000_reset_hw_80003es2lan,
.init_hw = e1000_init_hw_80003es2lan,
.setup_link = e1000e_setup_link,
@@ -1212,19 +1292,17 @@ struct e1000_info e1000_es2_info = {
.mac = e1000_80003es2lan,
.flags = FLAG_HAS_HW_VLAN_FILTER
| FLAG_HAS_JUMBO_FRAMES
- | FLAG_HAS_STATS_PTC_PRC
| FLAG_HAS_WOL
| FLAG_APME_IN_CTRL3
| FLAG_RX_CSUM_ENABLED
| FLAG_HAS_CTRLEXT_ON_LOAD
- | FLAG_HAS_STATS_ICR_ICT
| FLAG_RX_NEEDS_RESTART /* errata */
| FLAG_TARC_SET_BIT_ZERO /* errata */
| FLAG_APME_CHECK_PORT_B
| FLAG_DISABLE_FC_PAUSE_TIME /* errata */
| FLAG_TIPG_MEDIUM_FOR_80003ESLAN,
.pba = 38,
- .get_invariants = e1000_get_invariants_80003es2lan,
+ .get_variants = e1000_get_variants_80003es2lan,
.mac_ops = &es2_mac_ops,
.phy_ops = &es2_phy_ops,
.nvm_ops = &es2_nvm_ops,