diff options
Diffstat (limited to 'drivers/net/e1000e/netdev.c')
-rw-r--r-- | drivers/net/e1000e/netdev.c | 59 |
1 files changed, 49 insertions, 10 deletions
diff --git a/drivers/net/e1000e/netdev.c b/drivers/net/e1000e/netdev.c index cc0502bbb9f..ca5d3f58329 100644 --- a/drivers/net/e1000e/netdev.c +++ b/drivers/net/e1000e/netdev.c @@ -2785,7 +2785,7 @@ void e1000e_reset(struct e1000_adapter *adapter) else fc->pause_time = E1000_FC_PAUSE_TIME; fc->send_xon = 1; - fc->type = fc->original_type; + fc->current_mode = fc->requested_mode; /* Allow time for pending master requests to run */ mac->ops.reset_hw(hw); @@ -3408,7 +3408,10 @@ static void e1000_print_link_info(struct e1000_adapter *adapter) struct e1000_hw *hw = &adapter->hw; u32 ctrl = er32(CTRL); - e_info("Link is Up %d Mbps %s, Flow Control: %s\n", + /* Link status message must follow this format for user tools */ + printk(KERN_INFO "e1000e: %s NIC Link is Up %d Mbps %s, " + "Flow Control: %s\n", + adapter->netdev->name, adapter->link_speed, (adapter->link_duplex == FULL_DUPLEX) ? "Full Duplex" : "Half Duplex", @@ -3418,7 +3421,7 @@ static void e1000_print_link_info(struct e1000_adapter *adapter) ((ctrl & E1000_CTRL_TFCE) ? "TX" : "None" ))); } -static bool e1000_has_link(struct e1000_adapter *adapter) +bool e1000_has_link(struct e1000_adapter *adapter) { struct e1000_hw *hw = &adapter->hw; bool link_active = 0; @@ -3493,6 +3496,7 @@ static void e1000_watchdog_task(struct work_struct *work) struct e1000_adapter, watchdog_task); struct net_device *netdev = adapter->netdev; struct e1000_mac_info *mac = &adapter->hw.mac; + struct e1000_phy_info *phy = &adapter->hw.phy; struct e1000_ring *tx_ring = adapter->tx_ring; struct e1000_hw *hw = &adapter->hw; u32 link, tctl; @@ -3599,6 +3603,13 @@ static void e1000_watchdog_task(struct work_struct *work) tctl |= E1000_TCTL_EN; ew32(TCTL, tctl); + /* + * Perform any post-link-up configuration before + * reporting link up. + */ + if (phy->ops.cfg_on_link_up) + phy->ops.cfg_on_link_up(hw); + netif_carrier_on(netdev); netif_tx_wake_all_queues(netdev); @@ -3610,7 +3621,9 @@ static void e1000_watchdog_task(struct work_struct *work) if (netif_carrier_ok(netdev)) { adapter->link_speed = 0; adapter->link_duplex = 0; - e_info("Link is Down\n"); + /* Link status message must follow this format */ + printk(KERN_INFO "e1000e: %s NIC Link is Down\n", + adapter->netdev->name); netif_carrier_off(netdev); netif_tx_stop_all_queues(netdev); if (!test_bit(__E1000_DOWN, &adapter->state)) @@ -4462,7 +4475,27 @@ static int e1000_suspend(struct pci_dev *pdev, pm_message_t state) pci_disable_device(pdev); - pci_set_power_state(pdev, pci_choose_state(pdev, state)); + /* + * The pci-e switch on some quad port adapters will report a + * correctable error when the MAC transitions from D0 to D3. To + * prevent this we need to mask off the correctable errors on the + * downstream port of the pci-e switch. + */ + if (adapter->flags & FLAG_IS_QUAD_PORT) { + struct pci_dev *us_dev = pdev->bus->self; + int pos = pci_find_capability(us_dev, PCI_CAP_ID_EXP); + u16 devctl; + + pci_read_config_word(us_dev, pos + PCI_EXP_DEVCTL, &devctl); + pci_write_config_word(us_dev, pos + PCI_EXP_DEVCTL, + (devctl & ~PCI_EXP_DEVCTL_CERE)); + + pci_set_power_state(pdev, pci_choose_state(pdev, state)); + + pci_write_config_word(us_dev, pos + PCI_EXP_DEVCTL, devctl); + } else { + pci_set_power_state(pdev, pci_choose_state(pdev, state)); + } return 0; } @@ -4690,14 +4723,14 @@ static void e1000_eeprom_checks(struct e1000_adapter *adapter) return; ret_val = e1000_read_nvm(hw, NVM_INIT_CONTROL2_REG, 1, &buf); - if (!(le16_to_cpu(buf) & (1 << 0))) { + if (!ret_val && (!(le16_to_cpu(buf) & (1 << 0)))) { /* Deep Smart Power Down (DSPD) */ dev_warn(&adapter->pdev->dev, "Warning: detected DSPD enabled in EEPROM\n"); } ret_val = e1000_read_nvm(hw, NVM_INIT_3GIO_3, 1, &buf); - if (le16_to_cpu(buf) & (3 << 2)) { + if (!ret_val && (le16_to_cpu(buf) & (3 << 2))) { /* ASPM enable */ dev_warn(&adapter->pdev->dev, "Warning: detected ASPM enabled in EEPROM\n"); @@ -4782,7 +4815,10 @@ static int __devinit e1000_probe(struct pci_dev *pdev, goto err_pci_reg; pci_set_master(pdev); - pci_save_state(pdev); + /* PCI config space info */ + err = pci_save_state(pdev); + if (err) + goto err_alloc_etherdev; err = -ENOMEM; netdev = alloc_etherdev(sizeof(struct e1000_adapter)); @@ -4947,8 +4983,8 @@ static int __devinit e1000_probe(struct pci_dev *pdev, /* Initialize link parameters. User can change them with ethtool */ adapter->hw.mac.autoneg = 1; adapter->fc_autoneg = 1; - adapter->hw.fc.original_type = e1000_fc_default; - adapter->hw.fc.type = e1000_fc_default; + adapter->hw.fc.requested_mode = e1000_fc_default; + adapter->hw.fc.current_mode = e1000_fc_default; adapter->hw.phy.autoneg_advertised = 0x2f; /* ring size defaults */ @@ -4989,6 +5025,9 @@ static int __devinit e1000_probe(struct pci_dev *pdev, adapter->wol = adapter->eeprom_wol; device_set_wakeup_enable(&adapter->pdev->dev, adapter->wol); + /* save off EEPROM version number */ + e1000_read_nvm(&adapter->hw, 5, 1, &adapter->eeprom_vers); + /* reset the hardware with the new settings */ e1000e_reset(adapter); |