diff options
Diffstat (limited to 'drivers/net/wireless/libertas/README')
| -rw-r--r-- | drivers/net/wireless/libertas/README | 516 |
1 files changed, 0 insertions, 516 deletions
diff --git a/drivers/net/wireless/libertas/README b/drivers/net/wireless/libertas/README index 688da4c784b..378577200b5 100644 --- a/drivers/net/wireless/libertas/README +++ b/drivers/net/wireless/libertas/README @@ -40,64 +40,11 @@ NAME SYNOPSIS iwpriv <ethX> <command> [sub-command] ... - iwpriv ethX version - iwpriv ethX scantype [sub-command] - iwpriv ethX getSNR <n> - iwpriv ethX getNF <n> - iwpriv ethX getRSSI <n> - iwpriv ethX setrxant <n> - iwpriv ethX getrxant - iwpriv ethX settxant <n> - iwpriv ethX gettxant - iwpriv ethX authalgs <n> - iwpriv ethX pre-TBTT <n> - iwpriv ethX 8021xauthalgs <n> - iwpriv ethX encryptionmode <n> iwpriv ethX setregioncode <n> iwpriv ethX getregioncode - iwpriv ethX setbcnavg <n> - iwpriv ethX getbcnavg - iwpriv ethX setdataavg <n> - iwpriv ethX setlisteninter <n> - iwpriv ethX getlisteninter - iwpriv ethX setmultipledtim <n> - iwpriv ethX getmultipledtim - iwpriv ethX atimwindow <n> - iwpriv ethX deauth - iwpriv ethX adhocstop - iwpriv ethX radioon - iwpriv ethX radiooff - iwpriv ethX reasso-on - iwpriv ethX reasso-off - iwpriv ethX scanmode [sub-command] - iwpriv ethX setwpaie <n> - iwpriv ethX wlanidle-off - iwpriv ethX wlanidle-on - iwpriv ethX getcis - iwpriv ethX getlog - iwpriv ethX getadhocstatus - iwpriv ethX adhocgrate <n> - -Version 4 Command: - iwpriv ethX inactvityto <n> - iwpriv ethX sleeppd <n> - iwpriv ethX enable11d <n> - iwpriv ethX tpccfg <n> - iwpriv ethX powercfg <n> - iwpriv ethX setafc <n> - iwpriv ethX getafc Version 5 Command: iwpriv ethX ledgpio <n> - iwpriv ethX scanprobes <n> - iwpriv ethX lolisteninter <n> - iwpriv ethX rateadapt <n> <m> - iwpriv ethX txcontrol <n> - iwpriv ethX psnullinterval <n> - iwpriv ethX prescan <n> - iwpriv ethX getrxinfo - iwpriv ethX gettxrate - iwpriv ethX beaconinterval BT Commands: The blinding table (BT) contains a list of mac addresses that should be @@ -150,114 +97,6 @@ DESCRIPTION The ethX parameter specifies the network device that is to be used to perform this command on. it could be eth0, eth1 etc. -version - This is used to get the current version of the driver and the firmware. - -scantype - This command is used to set the scan type to be used by the driver in - the scan command. This setting will not be used while performing a scan - for a specific SSID, as it is always done with scan type being active. - - where the sub-commands are: - - active -- to set the scan type to active - passive -- to set the scan type to passive - get -- to get the scan type set in the driver - -getSNR - This command gets the average and non average value of Signal to Noise - Ratio of Beacon and Data. - - where value is:- - 0 -- Beacon non-average. - 1 -- Beacon average. - 2 -- Data non-average. - 3 -- Data average. - - If no value is given, all four values are returned in the order mentioned - above. - - Note: This command is available only when STA is connected. - -getRSSI - This command gets the average and non average value os Receive Signal - Strength of Beacon and Data. - - where value is:- - 0 -- Beacon non-average. - 1 -- Beacon average. - 2 -- Data non-average. - 3 -- Data average. - - Note: This command is available only when STA is connected. - -getNF - This command gets the average and non average value of Noise Floor of - Beacon and Data. - - where value is:- - 0 -- Beacon non-average. - 1 -- Beacon average. - 2 -- Data non-average. - 3 -- Data average. - - Note: This command is available only when STA is connected. - -setrxant - This command is used to set the mode for Rx antenna. - - The options that can be sent are:- - 1 -- Antenna 1. - 2 -- Antenna 2. - 0xFFFF -- Diversity. - - Usage: - iwpriv ethX setrxant 0x01: select Antenna 1. - -getrxant - This command is used to get the mode for Rx antenna. - - -settxant - This command is used to set the mode for Tx antenna. - The options that can be sent are:- - 1 -- Antenna 1. - 2 -- Antenna 2. - 0xFFFF -- Diversity. - Usage: - iwpriv ethX settxant 0x01: select Antenna 1. - -gettxant - This command is used to get the mode for Tx antenna. - -authalgs - This command is used by the WPA supplicant to set the authentication - algorithms in the station. - -8021xauthalgs - This command is used by the WPA supplicant to set the 8021.x authentication algorithm type - station. - - where values can be:- - 1 -- None - 2 -- LEAP - 4 -- TLS - 8 -- TTLs - 16 -- MD5 - - -encryptionmode - This command is used by the WPA supplicant to set the encryption algorithm. - - where values can be:- - 0 -- NONE - 1 -- WEP40 - 2 -- TKIP - 3 -- CCMP - 4 -- WEP104 - -pre-TBTT - This command is used to set pre-TBTT time period where value is in microseconds. - setregioncode This command is used to set the region code in the station. where value is 'region code' for various regions like @@ -270,114 +109,6 @@ getregioncode This command is used to get the region code information set in the station. -setbcnavg - Set the weighting factor for calculating RSSI. - -getbcnavg - Get weighting factor for calculating RSSI. - -setdataavg - Set the weighting factor for calculating SNR. - -setlisteninter - This command is used to set the listen interval in the - station. - - where the value ranges between 1 - 255 - -getlisteninter - This command is used to get the listen interval value set in the - station. - -setmultipledtim - This command is used to set the multiple dtim value in the - station. - where the value is 1,2,3,4,5,0xfffe - 0xfffe means the firmware will use listen interval in association - command for waking up - -getmultipledtim - This command is used to get the multiple dtim value set in the station. - -atimwindow - This command is used to set the atim value in the - station. - - where the value ranges between 0 - 50 - -deauth - This command is used to send the de-authentication to the AP with which - the station is associated. This command is valid only when - station is in Infrastructure mode. - - Note: This command is available only when STA is connected. - -adhocstop - This command is used to stop beacon transmission from the station and - go into idle state in ad-hoc mode. - - Note: This command is available only when STA is connected. - -radioon - This command is used to turn on the RF antenna. - -radiooff - This command is sued to turn off the RF antenna. - -scanmode - This command is used to set the station to scan for either IBSS - networks or BSS networks or both BSS and IBSS networks. This - command can be used with sub commands, - - where the value for - bss -- Scan All the BSS networks. - ibss -- Scan All the IBSS networks. - any -- Scan both BSS and IBSS networks. - - - -setwpaie - This command is used by WPA supplicant to send the WPA-IE to the driver. - -wlanidle-off - This command is used to get into idle state. - - Note: This command is available only when STA is connected. - -wlanidle-on - This command is used to get off the idle state. - - Note: This command is available only when STA is connected. - - -getlog - This command is used to get the 802.11 statistics available in the - station. - - Note: This command is available only when STA is connected. - -getadhocstatus - This command is used to get the ad-hoc Network Status. - - The various status codes are: - AdhocStarted - AdhocJoined - AdhocIdle - InfraMode - AutoUnknownMode - - Note: This command is available only when STA is connected. - -adhocgrate - This command is used to enable(1) g_rate, Disable(0) g_rate - and request(2) the status which g_rate is disabled/enabled, - for Ad-hoc creator. - - where value is:- - 0 -- Disabled - 1 -- Enabled - 2 -- Get - ledgpio This command is used to set/get LEDs. @@ -400,253 +131,6 @@ ledgpio Note: LED0 is invalid Note: Maximum Number of LEDs are 16. -inactivityto - This command is used by the host to set/get the inactivity timeout value, - which specifies when WLAN device is put to sleep. - - Usage: - iwpriv ethX inactivityto [<timeout>] - - where the parameter are: - timeout: timeout value in milliseconds. - - Example: - iwpriv eth1 inactivityto - "get the timeout value" - - iwpriv eth1 inactivityto X - "set timeout value to X ms" - - -sleeppd - This command is used to configure the sleep period of the WLAN device. - - Usage: - iwpriv ethX sleeppd [<sleep period>] - - where the parameter are: - Period: sleep period in milliseconds. Range 10~60. - - Example: - iwpriv eth1 sleeppd 10 - "set period as 10 ms" - iwpriv eth1 sleeppd - "get the sleep period configuration" - -enable11d - This command is used to control 11d - where value is:- - 1 -- Enabled - 0 -- Disabled - 2 -- Get - - - - -tpccfg - Enables or disables automatic transmit power control. - - The first parameter turns this feature on (1) or off (0). When turning - on, the user must also supply four more parameters in the following - order: - -UseSNR (Use SNR (in addition to PER) for TPC algorithm), - -P0 (P0 power level for TPC), - -P1 (P1 power level for TPC), - -P2 (P2 power level for TPC). - - Usage: - iwpriv ethX tpccfg: Get current configuration - iwpriv ethX tpccfg 0: disable auto TPC - iwpriv ethX tpccfg 0x01 0x00 0x05 0x0a 0x0d: enable auto TPC; do not use SNR; - P0=0x05; P1=0x0a; P2=0x0d; - iwpriv ethX tpccfg 0x01 0x01 0x05 0x0a 0x0d: enable auto TPC; use SNR; - P0=0x05; P1=0x0a; P2=0x0d. - -powercfg - Enables or disables power adaptation. - - The first parameter turns this feature on (1) or off (0). When turning - on, the user must also supply three more parameters in the following - order: - -P0 (P0 power level for Power Adaptation), - -P1 (P1 power level for Power Adaptation), - -P2 (P2 power level for Power Adaptation). - - Usage: - iwpriv ethX powercfg: Get current configuration - iwpriv ethX powercfg 0: disable power adaptation - iwpriv ethX powercfg 1 0x0d 0x0f 0x12: enable power adaptation; - P0=0x0d; P1=0x0f; P2=0x12. - -getafc - This command returns automatic frequency control parameters. It returns - three integers: - -P0: automatic is on (1), or off (0), - -P1: current timing offset in PPM (part per million), and - -P2: current frequency offset in PPM. - -setafc - Set automatic frequency control options. - - The first parameter turns automatic on (1) or off (0). - The user must supply two more parameters in either case, in the following - order: - - When auto is on: - - -P0 (automatic adjustment frequency threshold in PPM), - -P1 (automatic adjustment period in beacon period), - - When auto is off: - - -P0 (manual adjustment timing offset in PPM), and - -P1 (manual adjustment frequency offset in PPM). - - Usage: - iwpriv ethX setafc 0 10 10: manual adjustment, both timing and frequcncy - offset are 10 PPM. - - iwpriv ethX setafc 1 10 10 enable afc, automatic adjustment, - frequency threshold 10 PPM, for every 10 beacon periods. - - - -scanprobes - This command sets number of probe requests per channel. - - Usage: - iwpriv ethX scanprobes 3 (set scan probes to 3) - iwpriv ethX scanprobes (get scan probes) - -lolisteninter - This command sets the value of listen interval. - - Usage: - iwpriv ethX lolisteninter 234 (set the lolisteninter to 234) - iwpriv ethX lolisteninter (get the lolisteninter value) - -rateadapt - This command sets the data rates bitmap. - Where <n> - 0: Disable auto rate adapt - 1: Enable auto rate adapt - - <m> - data rate bitmap - Bit Data rate - 0 1 Mbps - 1 2 Mbps - 2 5.5 Mbps - 3 11 Mbps - 4 Reserved - 5 6 Mbps - 6 9 Mbps - 7 12 Mbps - 8 18 Mbps - 9 24 Mbps - 10 36 Mbps - 11 48 Mbps - 12 54 Mbps - 12-15 Reserved - - Usage: - iwpriv ethX rateadapt - read the currect data rate setting - iwpriv ethX rateadapt 1 0x07 - enable auto data rate adapt and - data rates are 1Mbps, 2Mbsp and 5.5Mbps - - -txcontrol - This command is used to set the Tx rate, ack policy, and retry limit on a per packet basis. - - Where value <n> is: - if bit[4] == 1: - bit[3:0] -- 0 1 2 3 4 5 6 7 8 9 10 11 12 13-16 - Data Rate(Mbps) -- 1 2 5.5 11 Rsv 6 9 12 18 24 36 48 54 Rsv - - bit[12:8] - if bit[12] == 1, bit[11:8] specifies the Tx retry limit. - - bit[14:13] specifies per packet ack policy: - bit[14:13] - 1 0 use immediate ack policy for this packet - 1 1 use no ack policy for this packet - 0 x use the per-packet ack policy setting - - Usage: - iwpriv ethX txcontrol 0x7513 - Use no-ack policy, 5 retires for Tx, 11Mbps rate - - - -psnullinterval - This command is used to set/request NULL package interval for Power Save - under infrastructure mode. - - where value is:- - -1 -- Disabled - n>0 -- Set interval as n (seconds) - -prescan - This command is used to enable (1)/disable(0) auto prescan before assoicate to the ap - - where value is:- - 0 -- Disabled - 1 -- Enabled - 2 -- Get - -getrxinfo - This command gets non average value of Signal to Noise Ratio of Data and rate index. - - The following table shows RateIndex and Rate - - RateIndex Data rate - 0 1 Mbps - 1 2 Mbps - 2 5.5 Mbps - 3 11 Mbps - 4 Reserved - 5 6 Mbps - 6 9 Mbps - 7 12 Mbps - 8 18 Mbps - 9 24 Mbps - 10 36 Mbps - 11 48 Mbps - 12 54 Mbps - 13-15 Reserved - -gettxrate - This command gets current Tx rate index of the first packet associated with Rate Adaptation. - - The following table shows RateIndex and Rate - - RateIndex Data rate - 0 1 Mbps - 1 2 Mbps - 2 5.5 Mbps - 3 11 Mbps - 4 Reserved - 5 6 Mbps - 6 9 Mbps - 7 12 Mbps - 8 18 Mbps - 9 24 Mbps - 10 36 Mbps - 11 48 Mbps - 12 54 Mbps - 13-15 Reserved - -bcninterval - This command is used to sets beacon interval in adhoc mode when an argument is given, and gets current adhoc - beacon interval when no argument is given. The valid beacon interval is between 20 - 1000, - default beacon interval is 100. - - Usage: - iwpriv ethX bcninterval 100 (set adhoc beacon interval to 100) - iwpriv ethX bcninterval (get adhoc beacon interval) - fwt_add This command is used to insert an entry into the FWT table. The list of parameters must follow the following structure: |