diff options
Diffstat (limited to 'drivers/serial/cpm_uart')
-rw-r--r-- | drivers/serial/cpm_uart/cpm_uart.h | 49 | ||||
-rw-r--r-- | drivers/serial/cpm_uart/cpm_uart_core.c | 280 | ||||
-rw-r--r-- | drivers/serial/cpm_uart/cpm_uart_cpm1.c | 54 | ||||
-rw-r--r-- | drivers/serial/cpm_uart/cpm_uart_cpm2.c | 14 |
4 files changed, 265 insertions, 132 deletions
diff --git a/drivers/serial/cpm_uart/cpm_uart.h b/drivers/serial/cpm_uart/cpm_uart.h index 73c8a088c16..aa5eb7ddeda 100644 --- a/drivers/serial/cpm_uart/cpm_uart.h +++ b/drivers/serial/cpm_uart/cpm_uart.h @@ -10,6 +10,8 @@ #define CPM_UART_H #include <linux/config.h> +#include <linux/platform_device.h> +#include <linux/fs_uart_pd.h> #if defined(CONFIG_CPM2) #include "cpm_uart_cpm2.h" @@ -26,14 +28,14 @@ #define FLAG_SMC 0x00000002 #define FLAG_CONSOLE 0x00000001 -#define UART_SMC1 0 -#define UART_SMC2 1 -#define UART_SCC1 2 -#define UART_SCC2 3 -#define UART_SCC3 4 -#define UART_SCC4 5 +#define UART_SMC1 fsid_smc1_uart +#define UART_SMC2 fsid_smc2_uart +#define UART_SCC1 fsid_scc1_uart +#define UART_SCC2 fsid_scc2_uart +#define UART_SCC3 fsid_scc3_uart +#define UART_SCC4 fsid_scc4_uart -#define UART_NR 6 +#define UART_NR fs_uart_nr #define RX_NUM_FIFO 4 #define RX_BUF_SIZE 32 @@ -64,6 +66,7 @@ struct uart_cpm_port { uint dp_addr; void *mem_addr; dma_addr_t dma_addr; + u32 mem_size; /* helpers */ int baud; int bits; @@ -90,4 +93,36 @@ void scc2_lineif(struct uart_cpm_port *pinfo); void scc3_lineif(struct uart_cpm_port *pinfo); void scc4_lineif(struct uart_cpm_port *pinfo); +/* + virtual to phys transtalion +*/ +static inline unsigned long cpu2cpm_addr(void* addr, struct uart_cpm_port *pinfo) +{ + int offset; + u32 val = (u32)addr; + /* sane check */ + if ((val >= (u32)pinfo->mem_addr) && + (val<((u32)pinfo->mem_addr + pinfo->mem_size))) { + offset = val - (u32)pinfo->mem_addr; + return pinfo->dma_addr+offset; + } + printk("%s(): address %x to translate out of range!\n", __FUNCTION__, val); + return 0; +} + +static inline void *cpm2cpu_addr(unsigned long addr, struct uart_cpm_port *pinfo) +{ + int offset; + u32 val = addr; + /* sane check */ + if ((val >= pinfo->dma_addr) && + (val<(pinfo->dma_addr + pinfo->mem_size))) { + offset = val - (u32)pinfo->dma_addr; + return (void*)(pinfo->mem_addr+offset); + } + printk("%s(): address %x to translate out of range!\n", __FUNCTION__, val); + return 0; +} + + #endif /* CPM_UART_H */ diff --git a/drivers/serial/cpm_uart/cpm_uart_core.c b/drivers/serial/cpm_uart/cpm_uart_core.c index b7bf4c698a4..ced193bf9e1 100644 --- a/drivers/serial/cpm_uart/cpm_uart_core.c +++ b/drivers/serial/cpm_uart/cpm_uart_core.c @@ -41,6 +41,7 @@ #include <linux/device.h> #include <linux/bootmem.h> #include <linux/dma-mapping.h> +#include <linux/fs_uart_pd.h> #include <asm/io.h> #include <asm/irq.h> @@ -60,7 +61,7 @@ /* Track which ports are configured as uarts */ int cpm_uart_port_map[UART_NR]; /* How many ports did we config as uarts */ -int cpm_uart_nr; +int cpm_uart_nr = 0; /**************************************************************/ @@ -71,18 +72,36 @@ static void cpm_uart_initbd(struct uart_cpm_port *pinfo); /**************************************************************/ -static inline unsigned long cpu2cpm_addr(void *addr) + +/* Place-holder for board-specific stuff */ +struct platform_device* __attribute__ ((weak)) __init +early_uart_get_pdev(int index) { - if ((unsigned long)addr >= CPM_ADDR) - return (unsigned long)addr; - return virt_to_bus(addr); + return NULL; } -static inline void *cpm2cpu_addr(unsigned long addr) + +void cpm_uart_count(void) { - if (addr >= CPM_ADDR) - return (void *)addr; - return bus_to_virt(addr); + cpm_uart_nr = 0; +#ifdef CONFIG_SERIAL_CPM_SMC1 + cpm_uart_port_map[cpm_uart_nr++] = UART_SMC1; +#endif +#ifdef CONFIG_SERIAL_CPM_SMC2 + cpm_uart_port_map[cpm_uart_nr++] = UART_SMC2; +#endif +#ifdef CONFIG_SERIAL_CPM_SCC1 + cpm_uart_port_map[cpm_uart_nr++] = UART_SCC1; +#endif +#ifdef CONFIG_SERIAL_CPM_SCC2 + cpm_uart_port_map[cpm_uart_nr++] = UART_SCC2; +#endif +#ifdef CONFIG_SERIAL_CPM_SCC3 + cpm_uart_port_map[cpm_uart_nr++] = UART_SCC3; +#endif +#ifdef CONFIG_SERIAL_CPM_SCC4 + cpm_uart_port_map[cpm_uart_nr++] = UART_SCC4; +#endif } /* @@ -258,7 +277,7 @@ static void cpm_uart_int_rx(struct uart_port *port, struct pt_regs *regs) } /* get pointer */ - cp = cpm2cpu_addr(bdp->cbd_bufaddr); + cp = cpm2cpu_addr(bdp->cbd_bufaddr, pinfo); /* loop through the buffer */ while (i-- > 0) { @@ -601,7 +620,7 @@ static int cpm_uart_tx_pump(struct uart_port *port) /* Pick next descriptor and fill from buffer */ bdp = pinfo->tx_cur; - p = cpm2cpu_addr(bdp->cbd_bufaddr); + p = cpm2cpu_addr(bdp->cbd_bufaddr, pinfo); *p++ = port->x_char; bdp->cbd_datlen = 1; @@ -628,7 +647,7 @@ static int cpm_uart_tx_pump(struct uart_port *port) while (!(bdp->cbd_sc & BD_SC_READY) && (xmit->tail != xmit->head)) { count = 0; - p = cpm2cpu_addr(bdp->cbd_bufaddr); + p = cpm2cpu_addr(bdp->cbd_bufaddr, pinfo); while (count < pinfo->tx_fifosize) { *p++ = xmit->buf[xmit->tail]; xmit->tail = (xmit->tail + 1) & (UART_XMIT_SIZE - 1); @@ -677,12 +696,12 @@ static void cpm_uart_initbd(struct uart_cpm_port *pinfo) mem_addr = pinfo->mem_addr; bdp = pinfo->rx_cur = pinfo->rx_bd_base; for (i = 0; i < (pinfo->rx_nrfifos - 1); i++, bdp++) { - bdp->cbd_bufaddr = cpu2cpm_addr(mem_addr); + bdp->cbd_bufaddr = cpu2cpm_addr(mem_addr, pinfo); bdp->cbd_sc = BD_SC_EMPTY | BD_SC_INTRPT; mem_addr += pinfo->rx_fifosize; } - bdp->cbd_bufaddr = cpu2cpm_addr(mem_addr); + bdp->cbd_bufaddr = cpu2cpm_addr(mem_addr, pinfo); bdp->cbd_sc = BD_SC_WRAP | BD_SC_EMPTY | BD_SC_INTRPT; /* Set the physical address of the host memory @@ -692,12 +711,12 @@ static void cpm_uart_initbd(struct uart_cpm_port *pinfo) mem_addr = pinfo->mem_addr + L1_CACHE_ALIGN(pinfo->rx_nrfifos * pinfo->rx_fifosize); bdp = pinfo->tx_cur = pinfo->tx_bd_base; for (i = 0; i < (pinfo->tx_nrfifos - 1); i++, bdp++) { - bdp->cbd_bufaddr = cpu2cpm_addr(mem_addr); + bdp->cbd_bufaddr = cpu2cpm_addr(mem_addr, pinfo); bdp->cbd_sc = BD_SC_INTRPT; mem_addr += pinfo->tx_fifosize; } - bdp->cbd_bufaddr = cpu2cpm_addr(mem_addr); + bdp->cbd_bufaddr = cpu2cpm_addr(mem_addr, pinfo); bdp->cbd_sc = BD_SC_WRAP | BD_SC_INTRPT; } @@ -829,14 +848,6 @@ static int cpm_uart_request_port(struct uart_port *port) if (pinfo->flags & FLAG_CONSOLE) return 0; - /* - * Setup any port IO, connect any baud rate generators, - * etc. This is expected to be handled by board - * dependant code - */ - if (pinfo->set_lineif) - pinfo->set_lineif(pinfo); - if (IS_SMC(pinfo)) { pinfo->smcp->smc_smcm &= ~(SMCM_RX | SMCM_TX); pinfo->smcp->smc_smcmr &= ~(SMCMR_REN | SMCMR_TEN); @@ -988,6 +999,54 @@ struct uart_cpm_port cpm_uart_ports[UART_NR] = { }, }; +int cpm_uart_drv_get_platform_data(struct platform_device *pdev, int is_con) +{ + struct resource *r; + struct fs_uart_platform_info *pdata = pdev->dev.platform_data; + int idx = pdata->fs_no; /* It is UART_SMCx or UART_SCCx index */ + struct uart_cpm_port *pinfo; + int line; + u32 mem, pram; + + for (line=0; line<UART_NR && cpm_uart_port_map[line]!=pdata->fs_no; line++); + + pinfo = (struct uart_cpm_port *) &cpm_uart_ports[idx]; + + pinfo->brg = pdata->brg; + + if (!is_con) { + pinfo->port.line = line; + pinfo->port.flags = UPF_BOOT_AUTOCONF; + } + + if (!(r = platform_get_resource_byname(pdev, IORESOURCE_MEM, "regs"))) + return -EINVAL; + mem = r->start; + + if (!(r = platform_get_resource_byname(pdev, IORESOURCE_MEM, "pram"))) + return -EINVAL; + pram = r->start; + + if(idx > fsid_smc2_uart) { + pinfo->sccp = (scc_t *)mem; + pinfo->sccup = (scc_uart_t *)pram; + } else { + pinfo->smcp = (smc_t *)mem; + pinfo->smcup = (smc_uart_t *)pram; + } + pinfo->tx_nrfifos = pdata->tx_num_fifo; + pinfo->tx_fifosize = pdata->tx_buf_size; + + pinfo->rx_nrfifos = pdata->rx_num_fifo; + pinfo->rx_fifosize = pdata->rx_buf_size; + + pinfo->port.uartclk = pdata->uart_clk; + pinfo->port.mapbase = (unsigned long)mem; + pinfo->port.irq = platform_get_irq(pdev, 0); + + return 0; +} + #ifdef CONFIG_SERIAL_CPM_CONSOLE /* * Print a string to the serial port trying not to disturb @@ -1027,7 +1086,7 @@ static void cpm_uart_console_write(struct console *co, const char *s, * If the buffer address is in the CPM DPRAM, don't * convert it. */ - cp = cpm2cpu_addr(bdp->cbd_bufaddr); + cp = cpm2cpu_addr(bdp->cbd_bufaddr, pinfo); *cp = *s; @@ -1044,7 +1103,7 @@ static void cpm_uart_console_write(struct console *co, const char *s, while ((bdp->cbd_sc & BD_SC_READY) != 0) ; - cp = cpm2cpu_addr(bdp->cbd_bufaddr); + cp = cpm2cpu_addr(bdp->cbd_bufaddr, pinfo); *cp = 13; bdp->cbd_datlen = 1; @@ -1067,9 +1126,7 @@ static void cpm_uart_console_write(struct console *co, const char *s, pinfo->tx_cur = (volatile cbd_t *) bdp; } -/* - * Setup console. Be careful is called early ! - */ + static int __init cpm_uart_console_setup(struct console *co, char *options) { struct uart_port *port; @@ -1080,9 +1137,27 @@ static int __init cpm_uart_console_setup(struct console *co, char *options) int flow = 'n'; int ret; + struct fs_uart_platform_info *pdata; + struct platform_device* pdev = early_uart_get_pdev(co->index); + port = (struct uart_port *)&cpm_uart_ports[cpm_uart_port_map[co->index]]; pinfo = (struct uart_cpm_port *)port; + if (!pdev) { + pr_info("cpm_uart: console: compat mode\n"); + /* compatibility - will be cleaned up */ + cpm_uart_init_portdesc(); + + if (pinfo->set_lineif) + pinfo->set_lineif(pinfo); + } else { + pdata = pdev->dev.platform_data; + if (pdata) + if (pdata->init_ioports) + pdata->init_ioports(); + + cpm_uart_drv_get_platform_data(pdev, 1); + } pinfo->flags |= FLAG_CONSOLE; @@ -1097,14 +1172,6 @@ static int __init cpm_uart_console_setup(struct console *co, char *options) baud = 9600; } - /* - * Setup any port IO, connect any baud rate generators, - * etc. This is expected to be handled by board - * dependant code - */ - if (pinfo->set_lineif) - pinfo->set_lineif(pinfo); - if (IS_SMC(pinfo)) { pinfo->smcp->smc_smcm &= ~(SMCM_RX | SMCM_TX); pinfo->smcp->smc_smcmr &= ~(SMCMR_REN | SMCMR_TEN); @@ -1143,11 +1210,8 @@ static struct console cpm_scc_uart_console = { int __init cpm_uart_console_init(void) { - int ret = cpm_uart_init_portdesc(); - - if (!ret) - register_console(&cpm_scc_uart_console); - return ret; + register_console(&cpm_scc_uart_console); + return 0; } console_initcall(cpm_uart_console_init); @@ -1165,44 +1229,130 @@ static struct uart_driver cpm_reg = { .minor = SERIAL_CPM_MINOR, .cons = CPM_UART_CONSOLE, }; - -static int __init cpm_uart_init(void) +static int cpm_uart_drv_probe(struct device *dev) { - int ret, i; - - printk(KERN_INFO "Serial: CPM driver $Revision: 0.01 $\n"); + struct platform_device *pdev = to_platform_device(dev); + struct fs_uart_platform_info *pdata; + int ret = -ENODEV; -#ifndef CONFIG_SERIAL_CPM_CONSOLE - ret = cpm_uart_init_portdesc(); - if (ret) + if(!pdev) { + printk(KERN_ERR"CPM UART: platform data missing!\n"); return ret; -#endif + } - cpm_reg.nr = cpm_uart_nr; - ret = uart_register_driver(&cpm_reg); + pdata = pdev->dev.platform_data; + pr_debug("cpm_uart_drv_probe: Adding CPM UART %d\n", + cpm_uart_port_map[pdata->fs_no]); - if (ret) + if ((ret = cpm_uart_drv_get_platform_data(pdev, 0))) return ret; - for (i = 0; i < cpm_uart_nr; i++) { - int con = cpm_uart_port_map[i]; - cpm_uart_ports[con].port.line = i; - cpm_uart_ports[con].port.flags = UPF_BOOT_AUTOCONF; - uart_add_one_port(&cpm_reg, &cpm_uart_ports[con].port); - } + if (pdata->init_ioports) + pdata->init_ioports(); - return ret; + ret = uart_add_one_port(&cpm_reg, &cpm_uart_ports[pdata->fs_no].port); + + return ret; } -static void __exit cpm_uart_exit(void) +static int cpm_uart_drv_remove(struct device *dev) +{ + struct platform_device *pdev = to_platform_device(dev); + struct fs_uart_platform_info *pdata = pdev->dev.platform_data; + + pr_debug("cpm_uart_drv_remove: Removing CPM UART %d\n", + cpm_uart_port_map[pdata->fs_no]); + + uart_remove_one_port(&cpm_reg, &cpm_uart_ports[pdata->fs_no].port); + return 0; +} + +static struct device_driver cpm_smc_uart_driver = { + .name = "fsl-cpm-smc:uart", + .bus = &platform_bus_type, + .probe = cpm_uart_drv_probe, + .remove = cpm_uart_drv_remove, +}; + +static struct device_driver cpm_scc_uart_driver = { + .name = "fsl-cpm-scc:uart", + .bus = &platform_bus_type, + .probe = cpm_uart_drv_probe, + .remove = cpm_uart_drv_remove, +}; + +/* + This is supposed to match uart devices on platform bus, + */ +static int match_is_uart (struct device* dev, void* data) { + struct platform_device* pdev = container_of(dev, struct platform_device, dev); + int ret = 0; + /* this was setfunc as uart */ + if(strstr(pdev->name,":uart")) { + ret = 1; + } + return ret; +} + + +static int cpm_uart_init(void) { + + int ret; int i; + struct device *dev; + printk(KERN_INFO "Serial: CPM driver $Revision: 0.02 $\n"); + + /* lookup the bus for uart devices */ + dev = bus_find_device(&platform_bus_type, NULL, 0, match_is_uart); + + /* There are devices on the bus - all should be OK */ + if (dev) { + cpm_uart_count(); + cpm_reg.nr = cpm_uart_nr; + + if (!(ret = uart_register_driver(&cpm_reg))) { + if ((ret = driver_register(&cpm_smc_uart_driver))) { + uart_unregister_driver(&cpm_reg); + return ret; + } + if ((ret = driver_register(&cpm_scc_uart_driver))) { + driver_unregister(&cpm_scc_uart_driver); + uart_unregister_driver(&cpm_reg); + } + } + } else { + /* No capable platform devices found - falling back to legacy mode */ + pr_info("cpm_uart: WARNING: no UART devices found on platform bus!\n"); + pr_info( + "cpm_uart: the driver will guess configuration, but this mode is no longer supported.\n"); +#ifndef CONFIG_SERIAL_CPM_CONSOLE + ret = cpm_uart_init_portdesc(); + if (ret) + return ret; +#endif + + cpm_reg.nr = cpm_uart_nr; + ret = uart_register_driver(&cpm_reg); + + if (ret) + return ret; + + for (i = 0; i < cpm_uart_nr; i++) { + int con = cpm_uart_port_map[i]; + cpm_uart_ports[con].port.line = i; + cpm_uart_ports[con].port.flags = UPF_BOOT_AUTOCONF; + uart_add_one_port(&cpm_reg, &cpm_uart_ports[con].port); + } - for (i = 0; i < cpm_uart_nr; i++) { - int con = cpm_uart_port_map[i]; - uart_remove_one_port(&cpm_reg, &cpm_uart_ports[con].port); } + return ret; +} +static void __exit cpm_uart_exit(void) +{ + driver_unregister(&cpm_scc_uart_driver); + driver_unregister(&cpm_smc_uart_driver); uart_unregister_driver(&cpm_reg); } diff --git a/drivers/serial/cpm_uart/cpm_uart_cpm1.c b/drivers/serial/cpm_uart/cpm_uart_cpm1.c index d789ee55cbb..a5a30622637 100644 --- a/drivers/serial/cpm_uart/cpm_uart_cpm1.c +++ b/drivers/serial/cpm_uart/cpm_uart_cpm1.c @@ -81,58 +81,11 @@ void cpm_line_cr_cmd(int line, int cmd) void smc1_lineif(struct uart_cpm_port *pinfo) { - volatile cpm8xx_t *cp = cpmp; - - (void)cp; /* fix warning */ -#if defined (CONFIG_MPC885ADS) - /* Enable SMC1 transceivers */ - { - cp->cp_pepar |= 0x000000c0; - cp->cp_pedir &= ~0x000000c0; - cp->cp_peso &= ~0x00000040; - cp->cp_peso |= 0x00000080; - } -#elif defined (CONFIG_MPC86XADS) - unsigned int iobits = 0x000000c0; - - if (!pinfo->is_portb) { - cp->cp_pbpar |= iobits; - cp->cp_pbdir &= ~iobits; - cp->cp_pbodr &= ~iobits; - } else { - ((immap_t *)IMAP_ADDR)->im_ioport.iop_papar |= iobits; - ((immap_t *)IMAP_ADDR)->im_ioport.iop_padir &= ~iobits; - ((immap_t *)IMAP_ADDR)->im_ioport.iop_paodr &= ~iobits; - } -#endif pinfo->brg = 1; } void smc2_lineif(struct uart_cpm_port *pinfo) { - volatile cpm8xx_t *cp = cpmp; - - (void)cp; /* fix warning */ -#if defined (CONFIG_MPC885ADS) - cp->cp_pepar |= 0x00000c00; - cp->cp_pedir &= ~0x00000c00; - cp->cp_peso &= ~0x00000400; - cp->cp_peso |= 0x00000800; -#elif defined (CONFIG_MPC86XADS) - unsigned int iobits = 0x00000c00; - - if (!pinfo->is_portb) { - cp->cp_pbpar |= iobits; - cp->cp_pbdir &= ~iobits; - cp->cp_pbodr &= ~iobits; - } else { - ((immap_t *)IMAP_ADDR)->im_ioport.iop_papar |= iobits; - ((immap_t *)IMAP_ADDR)->im_ioport.iop_padir &= ~iobits; - ((immap_t *)IMAP_ADDR)->im_ioport.iop_paodr &= ~iobits; - } - -#endif - pinfo->brg = 2; } @@ -191,7 +144,7 @@ int cpm_uart_allocbuf(struct uart_cpm_port *pinfo, unsigned int is_con) /* was hostalloc but changed cause it blows away the */ /* large tlb mapping when pinning the kernel area */ mem_addr = (u8 *) cpm_dpram_addr(cpm_dpalloc(memsz, 8)); - dma_addr = 0; + dma_addr = (u32)mem_addr; } else mem_addr = dma_alloc_coherent(NULL, memsz, &dma_addr, GFP_KERNEL); @@ -204,8 +157,9 @@ int cpm_uart_allocbuf(struct uart_cpm_port *pinfo, unsigned int is_con) } pinfo->dp_addr = dp_offset; - pinfo->mem_addr = mem_addr; - pinfo->dma_addr = dma_addr; + pinfo->mem_addr = mem_addr; /* virtual address*/ + pinfo->dma_addr = dma_addr; /* physical address*/ + pinfo->mem_size = memsz; pinfo->rx_buf = mem_addr; pinfo->tx_buf = pinfo->rx_buf + L1_CACHE_ALIGN(pinfo->rx_nrfifos diff --git a/drivers/serial/cpm_uart/cpm_uart_cpm2.c b/drivers/serial/cpm_uart/cpm_uart_cpm2.c index fd9e53ed3fe..7c6b07aeea9 100644 --- a/drivers/serial/cpm_uart/cpm_uart_cpm2.c +++ b/drivers/serial/cpm_uart/cpm_uart_cpm2.c @@ -142,14 +142,6 @@ void scc2_lineif(struct uart_cpm_port *pinfo) * be supported in a sane fashion. */ #ifndef CONFIG_STX_GP3 -#ifdef CONFIG_MPC8560_ADS - volatile iop_cpm2_t *io = &cpm2_immr->im_ioport; - io->iop_ppard |= 0x00000018; - io->iop_psord &= ~0x00000008; /* Rx */ - io->iop_psord &= ~0x00000010; /* Tx */ - io->iop_pdird &= ~0x00000008; /* Rx */ - io->iop_pdird |= 0x00000010; /* Tx */ -#else volatile iop_cpm2_t *io = &cpm2_immr->im_ioport; io->iop_pparb |= 0x008b0000; io->iop_pdirb |= 0x00880000; @@ -157,7 +149,6 @@ void scc2_lineif(struct uart_cpm_port *pinfo) io->iop_pdirb &= ~0x00030000; io->iop_psorb &= ~0x00030000; #endif -#endif cpm2_immr->im_cpmux.cmx_scr &= 0xff00ffff; cpm2_immr->im_cpmux.cmx_scr |= 0x00090000; pinfo->brg = 2; @@ -218,8 +209,10 @@ int cpm_uart_allocbuf(struct uart_cpm_port *pinfo, unsigned int is_con) memsz = L1_CACHE_ALIGN(pinfo->rx_nrfifos * pinfo->rx_fifosize) + L1_CACHE_ALIGN(pinfo->tx_nrfifos * pinfo->tx_fifosize); - if (is_con) + if (is_con) { mem_addr = alloc_bootmem(memsz); + dma_addr = mem_addr; + } else mem_addr = dma_alloc_coherent(NULL, memsz, &dma_addr, GFP_KERNEL); @@ -234,6 +227,7 @@ int cpm_uart_allocbuf(struct uart_cpm_port *pinfo, unsigned int is_con) pinfo->dp_addr = dp_offset; pinfo->mem_addr = mem_addr; pinfo->dma_addr = dma_addr; + pinfo->mem_size = memsz; pinfo->rx_buf = mem_addr; pinfo->tx_buf = pinfo->rx_buf + L1_CACHE_ALIGN(pinfo->rx_nrfifos |