aboutsummaryrefslogtreecommitdiff
path: root/drivers/serial
diff options
context:
space:
mode:
Diffstat (limited to 'drivers/serial')
-rw-r--r--drivers/serial/8250.c17
-rw-r--r--drivers/serial/8250_pci.c50
-rw-r--r--drivers/serial/8250_pnp.c2
-rw-r--r--drivers/serial/Kconfig2
-rw-r--r--drivers/serial/atmel_serial.c6
-rw-r--r--drivers/serial/jsm/jsm_driver.c5
-rw-r--r--drivers/serial/jsm/jsm_neo.c3
-rw-r--r--drivers/serial/jsm/jsm_tty.c6
-rw-r--r--drivers/serial/mcf.c11
-rw-r--r--drivers/serial/of_serial.c1
-rw-r--r--drivers/serial/pnx8xxx_uart.c23
-rw-r--r--drivers/serial/sh-sci.h5
12 files changed, 113 insertions, 18 deletions
diff --git a/drivers/serial/8250.c b/drivers/serial/8250.c
index 1889a63ebc2..b4b39811b44 100644
--- a/drivers/serial/8250.c
+++ b/drivers/serial/8250.c
@@ -2083,6 +2083,20 @@ static int serial8250_startup(struct uart_port *port)
serial8250_set_mctrl(&up->port, up->port.mctrl);
+ /* Serial over Lan (SoL) hack:
+ Intel 8257x Gigabit ethernet chips have a
+ 16550 emulation, to be used for Serial Over Lan.
+ Those chips take a longer time than a normal
+ serial device to signalize that a transmission
+ data was queued. Due to that, the above test generally
+ fails. One solution would be to delay the reading of
+ iir. However, this is not reliable, since the timeout
+ is variable. So, let's just don't test if we receive
+ TX irq. This way, we'll never enable UART_BUG_TXEN.
+ */
+ if (up->port.flags & UPF_NO_TXEN_TEST)
+ goto dont_test_tx_en;
+
/*
* Do a quick test to see if we receive an
* interrupt when we enable the TX irq.
@@ -2102,6 +2116,7 @@ static int serial8250_startup(struct uart_port *port)
up->bugs &= ~UART_BUG_TXEN;
}
+dont_test_tx_en:
spin_unlock_irqrestore(&up->port.lock, flags);
/*
@@ -2839,6 +2854,8 @@ int __init early_serial_setup(struct uart_port *port)
p->flags = port->flags;
p->mapbase = port->mapbase;
p->private_data = port->private_data;
+ p->type = port->type;
+ p->line = port->line;
set_io_from_upio(p);
if (port->serial_in)
diff --git a/drivers/serial/8250_pci.c b/drivers/serial/8250_pci.c
index c088146b751..533f82025ad 100644
--- a/drivers/serial/8250_pci.c
+++ b/drivers/serial/8250_pci.c
@@ -602,6 +602,10 @@ static int pci_netmos_init(struct pci_dev *dev)
/* subdevice 0x00PS means <P> parallel, <S> serial */
unsigned int num_serial = dev->subsystem_device & 0xf;
+ if (dev->subsystem_vendor == PCI_VENDOR_ID_IBM &&
+ dev->subsystem_device == 0x0299)
+ return 0;
+
if (num_serial == 0)
return -ENODEV;
return num_serial;
@@ -794,6 +798,21 @@ pci_default_setup(struct serial_private *priv,
return setup_port(priv, port, bar, offset, board->reg_shift);
}
+static int skip_tx_en_setup(struct serial_private *priv,
+ const struct pciserial_board *board,
+ struct uart_port *port, int idx)
+{
+ port->flags |= UPF_NO_TXEN_TEST;
+ printk(KERN_DEBUG "serial8250: skipping TxEn test for device "
+ "[%04x:%04x] subsystem [%04x:%04x]\n",
+ priv->dev->vendor,
+ priv->dev->device,
+ priv->dev->subsystem_vendor,
+ priv->dev->subsystem_device);
+
+ return pci_default_setup(priv, board, port, idx);
+}
+
/* This should be in linux/pci_ids.h */
#define PCI_VENDOR_ID_SBSMODULARIO 0x124B
#define PCI_SUBVENDOR_ID_SBSMODULARIO 0x124B
@@ -802,6 +821,8 @@ pci_default_setup(struct serial_private *priv,
#define PCI_SUBDEVICE_ID_OCTPRO422 0x0208
#define PCI_SUBDEVICE_ID_POCTAL232 0x0308
#define PCI_SUBDEVICE_ID_POCTAL422 0x0408
+#define PCI_VENDOR_ID_ADVANTECH 0x13fe
+#define PCI_DEVICE_ID_ADVANTECH_PCI3620 0x3620
/* Unknown vendors/cards - this should not be in linux/pci_ids.h */
#define PCI_SUBDEVICE_ID_UNKNOWN_0x1584 0x1584
@@ -858,6 +879,27 @@ static struct pci_serial_quirk pci_serial_quirks[] __refdata = {
.init = pci_inteli960ni_init,
.setup = pci_default_setup,
},
+ {
+ .vendor = PCI_VENDOR_ID_INTEL,
+ .device = PCI_DEVICE_ID_INTEL_8257X_SOL,
+ .subvendor = PCI_ANY_ID,
+ .subdevice = PCI_ANY_ID,
+ .setup = skip_tx_en_setup,
+ },
+ {
+ .vendor = PCI_VENDOR_ID_INTEL,
+ .device = PCI_DEVICE_ID_INTEL_82573L_SOL,
+ .subvendor = PCI_ANY_ID,
+ .subdevice = PCI_ANY_ID,
+ .setup = skip_tx_en_setup,
+ },
+ {
+ .vendor = PCI_VENDOR_ID_INTEL,
+ .device = PCI_DEVICE_ID_INTEL_82573E_SOL,
+ .subvendor = PCI_ANY_ID,
+ .subdevice = PCI_ANY_ID,
+ .setup = skip_tx_en_setup,
+ },
/*
* ITE
*/
@@ -2148,6 +2190,10 @@ static int pciserial_resume_one(struct pci_dev *dev)
#endif
static struct pci_device_id serial_pci_tbl[] = {
+ /* Advantech use PCI_DEVICE_ID_ADVANTECH_PCI3620 (0x3620) as 'PCI_SUBVENDOR_ID' */
+ { PCI_VENDOR_ID_ADVANTECH, PCI_DEVICE_ID_ADVANTECH_PCI3620,
+ PCI_DEVICE_ID_ADVANTECH_PCI3620, 0x0001, 0, 0,
+ pbn_b2_8_921600 },
{ PCI_VENDOR_ID_V3, PCI_DEVICE_ID_V3_V960,
PCI_SUBVENDOR_ID_CONNECT_TECH,
PCI_SUBDEVICE_ID_CONNECT_TECH_BH8_232, 0, 0,
@@ -3096,6 +3142,10 @@ static struct pci_device_id serial_pci_tbl[] = {
0,
pbn_b0_8_115200 },
+ { PCI_VENDOR_ID_NETMOS, PCI_DEVICE_ID_NETMOS_9835,
+ PCI_VENDOR_ID_IBM, 0x0299,
+ 0, 0, pbn_b0_bt_2_115200 },
+
/*
* These entries match devices with class COMMUNICATION_SERIAL,
* COMMUNICATION_MODEM or COMMUNICATION_MULTISERIAL
diff --git a/drivers/serial/8250_pnp.c b/drivers/serial/8250_pnp.c
index fde7f9ccf57..bbcfc26a3b6 100644
--- a/drivers/serial/8250_pnp.c
+++ b/drivers/serial/8250_pnp.c
@@ -270,6 +270,8 @@ static const struct pnp_device_id pnp_dev_table[] = {
{ "RSS0250", 0 },
/* SupraExpress 28.8 Data/Fax PnP modem */
{ "SUP1310", 0 },
+ /* SupraExpress 336i PnP Voice Modem */
+ { "SUP1381", 0 },
/* SupraExpress 33.6 Data/Fax PnP modem */
{ "SUP1421", 0 },
/* SupraExpress 33.6 Data/Fax PnP modem */
diff --git a/drivers/serial/Kconfig b/drivers/serial/Kconfig
index 3e525e38a5d..7d7f576da20 100644
--- a/drivers/serial/Kconfig
+++ b/drivers/serial/Kconfig
@@ -982,7 +982,7 @@ config SERIAL_SH_SCI_CONSOLE
config SERIAL_PNX8XXX
bool "Enable PNX8XXX SoCs' UART Support"
- depends on MIPS && SOC_PNX8550
+ depends on MIPS && (SOC_PNX8550 || SOC_PNX833X)
select SERIAL_CORE
help
If you have a MIPS-based Philips SoC such as PNX8550 or PNX8330
diff --git a/drivers/serial/atmel_serial.c b/drivers/serial/atmel_serial.c
index d5efd6c7790..8f58f7ff0dd 100644
--- a/drivers/serial/atmel_serial.c
+++ b/drivers/serial/atmel_serial.c
@@ -579,7 +579,7 @@ static void atmel_tx_dma(struct uart_port *port)
/* disable PDC transmit */
UART_PUT_PTCR(port, ATMEL_PDC_TXTDIS);
- if (!uart_circ_empty(xmit)) {
+ if (!uart_circ_empty(xmit) && !uart_tx_stopped(port)) {
dma_sync_single_for_device(port->dev,
pdc->dma_addr,
pdc->dma_size,
@@ -877,6 +877,10 @@ static int atmel_startup(struct uart_port *port)
}
}
+ /* Save current CSR for comparison in atmel_tasklet_func() */
+ atmel_port->irq_status_prev = UART_GET_CSR(port);
+ atmel_port->irq_status = atmel_port->irq_status_prev;
+
/*
* Finally, enable the serial port
*/
diff --git a/drivers/serial/jsm/jsm_driver.c b/drivers/serial/jsm/jsm_driver.c
index 338cf8a08b4..ac79cbe4c2c 100644
--- a/drivers/serial/jsm/jsm_driver.c
+++ b/drivers/serial/jsm/jsm_driver.c
@@ -84,6 +84,8 @@ static int jsm_probe_one(struct pci_dev *pdev, const struct pci_device_id *ent)
brd->pci_dev = pdev;
if (pdev->device == PCIE_DEVICE_ID_NEO_4_IBM)
brd->maxports = 4;
+ else if (pdev->device == PCI_DEVICE_ID_DIGI_NEO_8)
+ brd->maxports = 8;
else
brd->maxports = 2;
@@ -180,7 +182,7 @@ static int jsm_probe_one(struct pci_dev *pdev, const struct pci_device_id *ent)
return rc;
}
-static void jsm_remove_one(struct pci_dev *pdev)
+static void __devexit jsm_remove_one(struct pci_dev *pdev)
{
struct jsm_board *brd = pci_get_drvdata(pdev);
int i = 0;
@@ -212,6 +214,7 @@ static struct pci_device_id jsm_pci_tbl[] = {
{ PCI_DEVICE(PCI_VENDOR_ID_DIGI, PCI_DEVICE_ID_NEO_2RJ45), 0, 0, 2 },
{ PCI_DEVICE(PCI_VENDOR_ID_DIGI, PCI_DEVICE_ID_NEO_2RJ45PRI), 0, 0, 3 },
{ PCI_DEVICE(PCI_VENDOR_ID_DIGI, PCIE_DEVICE_ID_NEO_4_IBM), 0, 0, 4 },
+ { PCI_DEVICE(PCI_VENDOR_ID_DIGI, PCI_DEVICE_ID_DIGI_NEO_8), 0, 0, 5 },
{ 0, }
};
MODULE_DEVICE_TABLE(pci, jsm_pci_tbl);
diff --git a/drivers/serial/jsm/jsm_neo.c b/drivers/serial/jsm/jsm_neo.c
index b7584ca55ad..e6390d02363 100644
--- a/drivers/serial/jsm/jsm_neo.c
+++ b/drivers/serial/jsm/jsm_neo.c
@@ -577,9 +577,6 @@ static void neo_parse_modem(struct jsm_channel *ch, u8 signals)
jsm_printk(MSIGS, INFO, &ch->ch_bd->pci_dev,
"neo_parse_modem: port: %d msignals: %x\n", ch->ch_portnum, msignals);
- if (!ch)
- return;
-
/* Scrub off lower bits. They signify delta's, which I don't care about */
/* Keep DDCD and DDSR though */
msignals &= 0xf8;
diff --git a/drivers/serial/jsm/jsm_tty.c b/drivers/serial/jsm/jsm_tty.c
index 3547558d2ca..324c74d2f66 100644
--- a/drivers/serial/jsm/jsm_tty.c
+++ b/drivers/serial/jsm/jsm_tty.c
@@ -161,6 +161,11 @@ static void jsm_tty_stop_rx(struct uart_port *port)
channel->ch_bd->bd_ops->disable_receiver(channel);
}
+static void jsm_tty_enable_ms(struct uart_port *port)
+{
+ /* Nothing needed */
+}
+
static void jsm_tty_break(struct uart_port *port, int break_state)
{
unsigned long lock_flags;
@@ -345,6 +350,7 @@ static struct uart_ops jsm_ops = {
.start_tx = jsm_tty_start_tx,
.send_xchar = jsm_tty_send_xchar,
.stop_rx = jsm_tty_stop_rx,
+ .enable_ms = jsm_tty_enable_ms,
.break_ctl = jsm_tty_break,
.startup = jsm_tty_open,
.shutdown = jsm_tty_close,
diff --git a/drivers/serial/mcf.c b/drivers/serial/mcf.c
index b2001c5b145..56841fe5f48 100644
--- a/drivers/serial/mcf.c
+++ b/drivers/serial/mcf.c
@@ -212,10 +212,18 @@ static void mcf_set_termios(struct uart_port *port, struct ktermios *termios,
{
unsigned long flags;
unsigned int baud, baudclk;
+#if defined(CONFIG_M5272)
+ unsigned int baudfr;
+#endif
unsigned char mr1, mr2;
baud = uart_get_baud_rate(port, termios, old, 0, 230400);
+#if defined(CONFIG_M5272)
+ baudclk = (MCF_BUSCLK / baud) / 32;
+ baudfr = (((MCF_BUSCLK / baud) + 1) / 2) % 16;
+#else
baudclk = ((MCF_BUSCLK / baud) + 16) / 32;
+#endif
mr1 = MCFUART_MR1_RXIRQRDY | MCFUART_MR1_RXERRCHAR;
mr2 = 0;
@@ -262,6 +270,9 @@ static void mcf_set_termios(struct uart_port *port, struct ktermios *termios,
writeb(mr2, port->membase + MCFUART_UMR);
writeb((baudclk & 0xff00) >> 8, port->membase + MCFUART_UBG1);
writeb((baudclk & 0xff), port->membase + MCFUART_UBG2);
+#if defined(CONFIG_M5272)
+ writeb((baudfr & 0x0f), port->membase + MCFUART_UFPD);
+#endif
writeb(MCFUART_UCSR_RXCLKTIMER | MCFUART_UCSR_TXCLKTIMER,
port->membase + MCFUART_UCSR);
writeb(MCFUART_UCR_RXENABLE | MCFUART_UCR_TXENABLE,
diff --git a/drivers/serial/of_serial.c b/drivers/serial/of_serial.c
index a821e3a3d66..14f8fa9135b 100644
--- a/drivers/serial/of_serial.c
+++ b/drivers/serial/of_serial.c
@@ -163,6 +163,7 @@ static struct of_device_id __devinitdata of_platform_serial_table[] = {
{ .type = "serial", .compatible = "ns16450", .data = (void *)PORT_16450, },
{ .type = "serial", .compatible = "ns16550", .data = (void *)PORT_16550, },
{ .type = "serial", .compatible = "ns16750", .data = (void *)PORT_16750, },
+ { .type = "serial", .compatible = "ns16850", .data = (void *)PORT_16850, },
#ifdef CONFIG_SERIAL_OF_PLATFORM_NWPSERIAL
{ .type = "serial", .compatible = "ibm,qpace-nwp-serial",
.data = (void *)PORT_NWPSERIAL, },
diff --git a/drivers/serial/pnx8xxx_uart.c b/drivers/serial/pnx8xxx_uart.c
index 22e30d21225..1bb8f1b4576 100644
--- a/drivers/serial/pnx8xxx_uart.c
+++ b/drivers/serial/pnx8xxx_uart.c
@@ -187,7 +187,7 @@ static void pnx8xxx_rx_chars(struct pnx8xxx_port *sport)
status = FIFO_TO_SM(serial_in(sport, PNX8XXX_FIFO)) |
ISTAT_TO_SM(serial_in(sport, PNX8XXX_ISTAT));
while (status & FIFO_TO_SM(PNX8XXX_UART_FIFO_RXFIFO)) {
- ch = serial_in(sport, PNX8XXX_FIFO);
+ ch = serial_in(sport, PNX8XXX_FIFO) & 0xff;
sport->port.icount.rx++;
@@ -198,9 +198,16 @@ static void pnx8xxx_rx_chars(struct pnx8xxx_port *sport)
* out of the main execution path
*/
if (status & (FIFO_TO_SM(PNX8XXX_UART_FIFO_RXFE |
- PNX8XXX_UART_FIFO_RXPAR) |
+ PNX8XXX_UART_FIFO_RXPAR |
+ PNX8XXX_UART_FIFO_RXBRK) |
ISTAT_TO_SM(PNX8XXX_UART_INT_RXOVRN))) {
- if (status & FIFO_TO_SM(PNX8XXX_UART_FIFO_RXPAR))
+ if (status & FIFO_TO_SM(PNX8XXX_UART_FIFO_RXBRK)) {
+ status &= ~(FIFO_TO_SM(PNX8XXX_UART_FIFO_RXFE) |
+ FIFO_TO_SM(PNX8XXX_UART_FIFO_RXPAR));
+ sport->port.icount.brk++;
+ if (uart_handle_break(&sport->port))
+ goto ignore_char;
+ } else if (status & FIFO_TO_SM(PNX8XXX_UART_FIFO_RXPAR))
sport->port.icount.parity++;
else if (status & FIFO_TO_SM(PNX8XXX_UART_FIFO_RXFE))
sport->port.icount.frame++;
@@ -284,14 +291,8 @@ static irqreturn_t pnx8xxx_int(int irq, void *dev_id)
/* Get the interrupts */
status = serial_in(sport, PNX8XXX_ISTAT) & serial_in(sport, PNX8XXX_IEN);
- /* Break signal received */
- if (status & PNX8XXX_UART_INT_BREAK) {
- sport->port.icount.brk++;
- uart_handle_break(&sport->port);
- }
-
- /* Byte received */
- if (status & PNX8XXX_UART_INT_RX)
+ /* Byte or break signal received */
+ if (status & (PNX8XXX_UART_INT_RX | PNX8XXX_UART_INT_BREAK))
pnx8xxx_rx_chars(sport);
/* TX holding register empty - transmit a byte */
diff --git a/drivers/serial/sh-sci.h b/drivers/serial/sh-sci.h
index 38c600c0dbb..3599828b976 100644
--- a/drivers/serial/sh-sci.h
+++ b/drivers/serial/sh-sci.h
@@ -32,7 +32,9 @@
#elif defined(CONFIG_CPU_SUBTYPE_SH7720) || \
defined(CONFIG_CPU_SUBTYPE_SH7721)
# define SCSCR_INIT(port) 0x0030 /* TIE=0,RIE=0,TE=1,RE=1 */
-#define SCIF_ORER 0x0200 /* overrun error bit */
+# define PORT_PTCR 0xA405011EUL
+# define PORT_PVCR 0xA4050122UL
+# define SCIF_ORER 0x0200 /* overrun error bit */
#elif defined(CONFIG_SH_RTS7751R2D)
# define SCSPTR1 0xFFE0001C /* 8 bit SCIF */
# define SCSPTR2 0xFFE80020 /* 16 bit SCIF */
@@ -393,6 +395,7 @@ SCIx_FNS(SCSCR, 0x08, 16, 0x08, 16)
SCIx_FNS(SCxTDR, 0x20, 8, 0x0c, 8)
SCIx_FNS(SCxSR, 0x14, 16, 0x10, 16)
SCIx_FNS(SCxRDR, 0x24, 8, 0x14, 8)
+SCIx_FNS(SCSPTR, 0, 0, 0, 0)
SCIF_FNS(SCTDSR, 0x0c, 8)
SCIF_FNS(SCFER, 0x10, 16)
SCIF_FNS(SCFCR, 0x18, 16)
generated by cgit v1.2.3 (git 2.25.1) at 2024-07-13 22:08:37 +0000