diff options
Diffstat (limited to 'drivers/spi/Kconfig')
| -rw-r--r-- | drivers/spi/Kconfig | 109 |
1 files changed, 109 insertions, 0 deletions
diff --git a/drivers/spi/Kconfig b/drivers/spi/Kconfig new file mode 100644 index 00000000000..b77dbd63e59 --- /dev/null +++ b/drivers/spi/Kconfig @@ -0,0 +1,109 @@ +# +# SPI driver configuration +# +# NOTE: the reason this doesn't show SPI slave support is mostly that +# nobody's needed a slave side API yet. The master-role API is not +# fully appropriate there, so it'd need some thought to do well. +# +menu "SPI support" + +config SPI + bool "SPI support" + help + The "Serial Peripheral Interface" is a low level synchronous + protocol. Chips that support SPI can have data transfer rates + up to several tens of Mbit/sec. Chips are addressed with a + controller and a chipselect. Most SPI slaves don't support + dynamic device discovery; some are even write-only or read-only. + + SPI is widely used by microcontollers to talk with sensors, + eeprom and flash memory, codecs and various other controller + chips, analog to digital (and d-to-a) converters, and more. + MMC and SD cards can be accessed using SPI protocol; and for + DataFlash cards used in MMC sockets, SPI must always be used. + + SPI is one of a family of similar protocols using a four wire + interface (select, clock, data in, data out) including Microwire + (half duplex), SSP, SSI, and PSP. This driver framework should + work with most such devices and controllers. + +config SPI_DEBUG + boolean "Debug support for SPI drivers" + depends on SPI && DEBUG_KERNEL + help + Say "yes" to enable debug messaging (like dev_dbg and pr_debug), + sysfs, and debugfs support in SPI controller and protocol drivers. + +# +# MASTER side ... talking to discrete SPI slave chips including microcontrollers +# + +config SPI_MASTER +# boolean "SPI Master Support" + boolean + default SPI + help + If your system has an master-capable SPI controller (which + provides the clock and chipselect), you can enable that + controller and the protocol drivers for the SPI slave chips + that are connected. + +comment "SPI Master Controller Drivers" + depends on SPI_MASTER + +config SPI_BITBANG + tristate "Bitbanging SPI master" + depends on SPI_MASTER && EXPERIMENTAL + help + With a few GPIO pins, your system can bitbang the SPI protocol. + Select this to get SPI support through I/O pins (GPIO, parallel + port, etc). Or, some systems' SPI master controller drivers use + this code to manage the per-word or per-transfer accesses to the + hardware shift registers. + + This is library code, and is automatically selected by drivers that + need it. You only need to select this explicitly to support driver + modules that aren't part of this kernel tree. + +config SPI_BUTTERFLY + tristate "Parallel port adapter for AVR Butterfly (DEVELOPMENT)" + depends on SPI_MASTER && PARPORT && EXPERIMENTAL + select SPI_BITBANG + help + This uses a custom parallel port cable to connect to an AVR + Butterfly <http://www.atmel.com/products/avr/butterfly>, an + inexpensive battery powered microcontroller evaluation board. + This same cable can be used to flash new firmware. + +config SPI_BUTTERFLY + tristate "Parallel port adapter for AVR Butterfly (DEVELOPMENT)" + depends on SPI_MASTER && PARPORT && EXPERIMENTAL + select SPI_BITBANG + help + This uses a custom parallel port cable to connect to an AVR + Butterfly <http://www.atmel.com/products/avr/butterfly>, an + inexpensive battery powered microcontroller evaluation board. + This same cable can be used to flash new firmware. + +# +# Add new SPI master controllers in alphabetical order above this line +# + + +# +# There are lots of SPI device types, with sensors and memory +# being probably the most widely used ones. +# +comment "SPI Protocol Masters" + depends on SPI_MASTER + + +# +# Add new SPI protocol masters in alphabetical order above this line +# + + +# (slave support would go here) + +endmenu # "SPI support" + |