diff options
Diffstat (limited to 'drivers/staging/rt3070/common/mlme.c')
| -rw-r--r-- | drivers/staging/rt3070/common/mlme.c | 83 |
1 files changed, 0 insertions, 83 deletions
diff --git a/drivers/staging/rt3070/common/mlme.c b/drivers/staging/rt3070/common/mlme.c index 0189bab013c..f5c386b500a 100644 --- a/drivers/staging/rt3070/common/mlme.c +++ b/drivers/staging/rt3070/common/mlme.c @@ -590,14 +590,6 @@ VOID MlmeHandler( break; } -#ifdef RALINK_ATE - if(ATE_ON(pAd)) - { - DBGPRINT(RT_DEBUG_TRACE, ("The driver is in ATE mode now in MlmeHandler\n")); - break; - } -#endif // RALINK_ATE // - //From message type, determine which state machine I should drive if (MlmeDequeue(&pAd->Mlme.Queue, &Elem)) { @@ -844,18 +836,6 @@ VOID MlmePeriodicExec( RT28XX_MLME_PRE_SANITY_CHECK(pAd); -#ifdef RALINK_ATE - /* Do not show RSSI until "Normal 1 second Mlme PeriodicExec". */ - if (ATE_ON(pAd)) - { - if (pAd->Mlme.PeriodicRound % MLME_TASK_EXEC_MULTIPLE != (MLME_TASK_EXEC_MULTIPLE - 1)) - { - pAd->Mlme.PeriodicRound ++; - return; - } - } -#endif // RALINK_ATE // - #ifdef CONFIG_STA_SUPPORT IF_DEV_CONFIG_OPMODE_ON_STA(pAd) { @@ -913,30 +893,6 @@ VOID MlmePeriodicExec( { pAd->Mlme.OneSecPeriodicRound ++; -#ifdef RALINK_ATE - if (ATE_ON(pAd)) - { - /* request from Baron : move this routine from later to here */ - /* for showing Rx error count in ATE RXFRAME */ - NICUpdateRawCounters(pAd); - if (pAd->ate.bRxFer == 1) - { - pAd->ate.RxTotalCnt += pAd->ate.RxCntPerSec; - ate_print(KERN_EMERG "MlmePeriodicExec: Rx packet cnt = %d/%d\n", pAd->ate.RxCntPerSec, pAd->ate.RxTotalCnt); - pAd->ate.RxCntPerSec = 0; - - if (pAd->ate.RxAntennaSel == 0) - ate_print(KERN_EMERG "MlmePeriodicExec: Rx AvgRssi0=%d, AvgRssi1=%d, AvgRssi2=%d\n\n", - pAd->ate.AvgRssi0, pAd->ate.AvgRssi1, pAd->ate.AvgRssi2); - else - ate_print(KERN_EMERG "MlmePeriodicExec: Rx AvgRssi=%d\n\n", pAd->ate.AvgRssi0); - } - MlmeResetRalinkCounters(pAd); - return; - } -#endif // RALINK_ATE // - - if (rx_Total) { @@ -1052,17 +1008,6 @@ VOID STAMlmePeriodicExec( ULONG TxTotalCnt; int i; -// -// We return here in ATE mode, because the statistics -// that ATE needs are not collected via this routine. -// -#ifdef RALINK_ATE - // It is supposed that we will never reach here in ATE mode. - ASSERT(!(ATE_ON(pAd))); - if (ATE_ON(pAd)) - return; -#endif // RALINK_ATE // - #ifdef WPA_SUPPLICANT_SUPPORT if (pAd->StaCfg.WpaSupplicantUP == WPA_SUPPLICANT_DISABLE) #endif // WPA_SUPPLICANT_SUPPORT // @@ -2024,13 +1969,6 @@ VOID MlmeDynamicTxRateSwitching( ULONG TxRetransmit = 0, TxSuccess = 0, TxFailCount = 0; MAC_TABLE_ENTRY *pEntry; -#ifdef RALINK_ATE - if (ATE_ON(pAd)) - { - return; - } -#endif // RALINK_ATE // - // // walk through MAC table, see if need to change AP's TX rate toward each entry // @@ -4870,12 +4808,6 @@ BOOLEAN MlmeEnqueueForRecv( INT MsgType; MLME_QUEUE *Queue = (MLME_QUEUE *)&pAd->Mlme.Queue; -#ifdef RALINK_ATE - /* Nothing to do in ATE mode */ - if(ATE_ON(pAd)) - return FALSE; -#endif // RALINK_ATE // - // Do nothing if the driver is starting halt state. // This might happen when timer already been fired before cancel timer with mlmehalt if (RTMP_TEST_FLAG(pAd, fRTMP_ADAPTER_HALT_IN_PROGRESS | fRTMP_ADAPTER_NIC_NOT_EXIST)) @@ -5550,11 +5482,6 @@ VOID AsicUpdateProtect( UCHAR i; UINT32 MacReg = 0; -#ifdef RALINK_ATE - if (ATE_ON(pAd)) - return; -#endif // RALINK_ATE // - #ifdef DOT11_N_SUPPORT if (!(pAd->CommonCfg.bHTProtect) && (OperationMode != 8)) { @@ -8411,11 +8338,6 @@ VOID AsicEvaluateRxAnt( { UCHAR BBPR3 = 0; -#ifdef RALINK_ATE - if (ATE_ON(pAd)) - return; -#endif // RALINK_ATE // - if (RTMP_TEST_FLAG(pAd, fRTMP_ADAPTER_RESET_IN_PROGRESS | fRTMP_ADAPTER_HALT_IN_PROGRESS | fRTMP_ADAPTER_RADIO_OFF | @@ -8530,11 +8452,6 @@ VOID AsicRxAntEvalTimeout( CHAR larger = -127, rssi0, rssi1, rssi2; #endif // CONFIG_STA_SUPPORT // -#ifdef RALINK_ATE - if (ATE_ON(pAd)) - return; -#endif // RALINK_ATE // - if (RTMP_TEST_FLAG(pAd, fRTMP_ADAPTER_RESET_IN_PROGRESS | fRTMP_ADAPTER_HALT_IN_PROGRESS | fRTMP_ADAPTER_RADIO_OFF | |