1 files changed, 89 insertions, 0 deletions
diff --git a/drivers/video/omap2/dss/Kconfig b/drivers/video/omap2/dss/Kconfig
new file mode 100644
index 00000000000..71d8dec3063
--- /dev/null
+++ b/drivers/video/omap2/dss/Kconfig
@@ -0,0 +1,89 @@
+menuconfig OMAP2_DSS
+        tristate "OMAP2/3 Display Subsystem support (EXPERIMENTAL)"
+        depends on ARCH_OMAP2 || ARCH_OMAP3
+        help
+          OMAP2/3 Display Subsystem support.
+
+if OMAP2_DSS
+
+config OMAP2_VRAM_SIZE
+	int "VRAM size (MB)"
+	range 0 32
+	default 0
+	help
+	  The amount of SDRAM to reserve at boot time for video RAM use.
+	  This VRAM will be used by omapfb and other drivers that need
+	  large continuous RAM area for video use.
+
+	  You can also set this with "vram=<bytes>" kernel argument, or
+	  in the board file.
+
+config OMAP2_DSS_DEBUG_SUPPORT
+        bool "Debug support"
+	default y
+	help
+	  This enables debug messages. You need to enable printing
+	  with 'debug' module parameter.
+
+config OMAP2_DSS_RFBI
+	bool "RFBI support"
+        default n
+	help
+	  MIPI DBI, or RFBI (Remote Framebuffer Interface), support.
+
+config OMAP2_DSS_VENC
+	bool "VENC support"
+        default y
+	help
+	  OMAP Video Encoder support.
+
+config OMAP2_DSS_SDI
+	bool "SDI support"
+	depends on ARCH_OMAP3
+        default n
+	help
+	  SDI (Serial Display Interface) support.
+
+config OMAP2_DSS_DSI
+	bool "DSI support"
+	depends on ARCH_OMAP3
+        default n
+	help
+	  MIPI DSI support.
+
+config OMAP2_DSS_USE_DSI_PLL
+	bool "Use DSI PLL for PCLK (EXPERIMENTAL)"
+	default n
+	depends on OMAP2_DSS_DSI
+	help
+	  Use DSI PLL to generate pixel clock.  Currently only for DPI output.
+	  DSI PLL can be used to generate higher and more precise pixel clocks.
+
+config OMAP2_DSS_FAKE_VSYNC
+	bool "Fake VSYNC irq from manual update displays"
+	default n
+	help
+	  If this is selected, DSI will generate a fake DISPC VSYNC interrupt
+	  when DSI has sent a frame. This is only needed with DSI or RFBI
+	  displays using manual mode, and you want VSYNC to, for example,
+	  time animation.
+
+config OMAP2_DSS_MIN_FCK_PER_PCK
+	int "Minimum FCK/PCK ratio (for scaling)"
+	range 0 32
+	default 0
+	help
+	  This can be used to adjust the minimum FCK/PCK ratio.
+
+	  With this you can make sure that DISPC FCK is at least
+	  n x PCK. Video plane scaling requires higher FCK than
+	  normally.
+
+	  If this is set to 0, there's no extra constraint on the
+	  DISPC FCK. However, the FCK will at minimum be
+	  2xPCK (if active matrix) or 3xPCK (if passive matrix).
+
+	  Max FCK is 173MHz, so this doesn't work if your PCK
+	  is very high.
+
+endif