diff options
Diffstat (limited to 'drivers')
| -rw-r--r-- | drivers/acpi/Kconfig | 64 | ||||
| -rw-r--r-- | drivers/acpi/processor_throttling.c | 59 | ||||
| -rw-r--r-- | drivers/acpi/sleep/Makefile | 4 | ||||
| -rw-r--r-- | drivers/acpi/sleep/main.c | 162 | ||||
| -rw-r--r-- | drivers/acpi/sleep/poweroff.c | 2 | ||||
| -rw-r--r-- | drivers/acpi/sleep/proc.c | 20 | ||||
| -rw-r--r-- | drivers/acpi/sleep/wakeup.c | 2 | ||||
| -rw-r--r-- | drivers/misc/asus-laptop.c | 32 | ||||
| -rw-r--r-- | drivers/pci/pci-acpi.c | 28 | ||||
| -rw-r--r-- | drivers/pci/pci.c | 8 | ||||
| -rw-r--r-- | drivers/pci/pci.h | 2 | ||||
| -rw-r--r-- | drivers/pnp/driver.c | 5 | ||||
| -rw-r--r-- | drivers/pnp/pnpacpi/core.c | 14 |
13 files changed, 276 insertions, 126 deletions
diff --git a/drivers/acpi/Kconfig b/drivers/acpi/Kconfig index 408b45168ab..251344cb29a 100644 --- a/drivers/acpi/Kconfig +++ b/drivers/acpi/Kconfig @@ -11,6 +11,9 @@ menuconfig ACPI depends on PCI depends on PM select PNP + # for sleep + select HOTPLUG_CPU if X86 && SMP + select SUSPEND_SMP if X86 && SMP default y ---help--- Advanced Configuration and Power Interface (ACPI) support for @@ -42,51 +45,26 @@ menuconfig ACPI if ACPI -config ACPI_SLEEP - bool "Sleep States" - depends on X86 && (!SMP || SUSPEND_SMP) - default y - ---help--- - This option adds support for ACPI suspend states. - - With this option, you will be able to put the system "to sleep". - Sleep states are low power states for the system and devices. All - of the system operating state is saved to either memory or disk - (depending on the state), to allow the system to resume operation - quickly at your request. - - Although this option sounds really nifty, barely any of the device - drivers have been converted to the new driver model and hence few - have proper power management support. - - This option is not recommended for anyone except those doing driver - power management development. - -config ACPI_SLEEP_PROC_FS - bool - depends on ACPI_SLEEP && PROC_FS - default y - -config ACPI_SLEEP_PROC_SLEEP - bool "/proc/acpi/sleep (deprecated)" - depends on ACPI_SLEEP_PROC_FS - default n - ---help--- - Create /proc/acpi/sleep - Deprecated by /sys/power/state - config ACPI_PROCFS - bool "Procfs interface (deprecated)" - default y + bool "Deprecated /proc/acpi files" + depends on PROC_FS ---help--- - The Procfs interface for ACPI is made optional for backward compatibility. - As the same functions are duplicated in the sysfs interface - and this proc interface will be removed some time later, - it's marked as deprecated. - ( /proc/acpi/debug_layer && debug_level are deprecated by - /sys/module/acpi/parameters/debug_layer && debug_level. - /proc/acpi/info is deprecated by - /sys/module/acpi/parameters/acpica_version ) + For backwards compatibility, this option allows + depricated /proc/acpi/ files to exist, even when + they have been replaced by functions in /sys. + The deprecated files (and their replacements) include: + + /proc/acpi/sleep (/sys/power/state) + /proc/acpi/info (/sys/modules/acpi/parameters/acpica_version) + /proc/acpi/dsdt (/sys/firmware/acpi/tables/DSDT) + /proc/acpi/fadt (/sys/firmware/acpi/tables/FACP) + /proc/acpi/debug_layer (/sys/module/acpi/parameters/debug_layer) + /proc/acpi/debug_level (/sys/module/acpi/parameters/debug_level) + + This option has no effect on /proc/acpi/ files + and functions which do not yet exist in /sys. + + Say N to delete /proc/acpi/ files that have moved to /sys/ config ACPI_AC tristate "AC Adapter" diff --git a/drivers/acpi/processor_throttling.c b/drivers/acpi/processor_throttling.c index 3f55d1f90c1..0b8204e7082 100644 --- a/drivers/acpi/processor_throttling.c +++ b/drivers/acpi/processor_throttling.c @@ -47,6 +47,9 @@ ACPI_MODULE_NAME("processor_throttling"); static int acpi_processor_get_throttling(struct acpi_processor *pr); int acpi_processor_set_throttling(struct acpi_processor *pr, int state); +/* + * _TPC - Throttling Present Capabilities + */ static int acpi_processor_get_platform_limit(struct acpi_processor *pr) { acpi_status status = 0; @@ -55,8 +58,10 @@ static int acpi_processor_get_platform_limit(struct acpi_processor *pr) if (!pr) return -EINVAL; status = acpi_evaluate_integer(pr->handle, "_TPC", NULL, &tpc); - if (ACPI_FAILURE(status) && status != AE_NOT_FOUND) { - ACPI_EXCEPTION((AE_INFO, status, "Evaluating _TPC")); + if (ACPI_FAILURE(status)) { + if (status != AE_NOT_FOUND) { + ACPI_EXCEPTION((AE_INFO, status, "Evaluating _TPC")); + } return -ENODEV; } pr->throttling_platform_limit = (int)tpc; @@ -68,9 +73,9 @@ int acpi_processor_tstate_has_changed(struct acpi_processor *pr) return acpi_processor_get_platform_limit(pr); } -/* -------------------------------------------------------------------------- - _PTC, _TSS, _TSD support - -------------------------------------------------------------------------- */ +/* + * _PTC - Processor Throttling Control (and status) register location + */ static int acpi_processor_get_throttling_control(struct acpi_processor *pr) { int result = 0; @@ -81,7 +86,9 @@ static int acpi_processor_get_throttling_control(struct acpi_processor *pr) status = acpi_evaluate_object(pr->handle, "_PTC", NULL, &buffer); if (ACPI_FAILURE(status)) { - ACPI_EXCEPTION((AE_INFO, status, "Evaluating _PTC")); + if (status != AE_NOT_FOUND) { + ACPI_EXCEPTION((AE_INFO, status, "Evaluating _PTC")); + } return -ENODEV; } @@ -132,6 +139,10 @@ static int acpi_processor_get_throttling_control(struct acpi_processor *pr) return result; } + +/* + * _TSS - Throttling Supported States + */ static int acpi_processor_get_throttling_states(struct acpi_processor *pr) { int result = 0; @@ -144,7 +155,9 @@ static int acpi_processor_get_throttling_states(struct acpi_processor *pr) status = acpi_evaluate_object(pr->handle, "_TSS", NULL, &buffer); if (ACPI_FAILURE(status)) { - ACPI_EXCEPTION((AE_INFO, status, "Evaluating _TSS")); + if (status != AE_NOT_FOUND) { + ACPI_EXCEPTION((AE_INFO, status, "Evaluating _TSS")); + } return -ENODEV; } @@ -201,6 +214,10 @@ static int acpi_processor_get_throttling_states(struct acpi_processor *pr) return result; } + +/* + * _TSD - T-State Dependencies + */ static int acpi_processor_get_tsd(struct acpi_processor *pr) { int result = 0; @@ -213,6 +230,9 @@ static int acpi_processor_get_tsd(struct acpi_processor *pr) status = acpi_evaluate_object(pr->handle, "_TSD", NULL, &buffer); if (ACPI_FAILURE(status)) { + if (status != AE_NOT_FOUND) { + ACPI_EXCEPTION((AE_INFO, status, "Evaluating _TSD")); + } return -ENODEV; } @@ -525,9 +545,6 @@ int acpi_processor_get_throttling_info(struct acpi_processor *pr) int result = 0; int step = 0; int i = 0; - int no_ptc = 0; - int no_tss = 0; - int no_tsd = 0; ACPI_DEBUG_PRINT((ACPI_DB_INFO, "pblk_address[0x%08x] duty_offset[%d] duty_width[%d]\n", @@ -538,12 +555,14 @@ int acpi_processor_get_throttling_info(struct acpi_processor *pr) if (!pr) return -EINVAL; - /* TBD: Support ACPI 2.0 objects */ - no_ptc = acpi_processor_get_throttling_control(pr); - no_tss = acpi_processor_get_throttling_states(pr); - no_tsd = acpi_processor_get_tsd(pr); - - if (no_ptc || no_tss) { + /* + * Evaluate _PTC, _TSS and _TPC + * They must all be present or none of them can be used. + */ + if (acpi_processor_get_throttling_control(pr) || + acpi_processor_get_throttling_states(pr) || + acpi_processor_get_platform_limit(pr)) + { pr->throttling.acpi_processor_get_throttling = &acpi_processor_get_throttling_fadt; pr->throttling.acpi_processor_set_throttling = @@ -555,6 +574,8 @@ int acpi_processor_get_throttling_info(struct acpi_processor *pr) &acpi_processor_set_throttling_ptc; } + acpi_processor_get_tsd(pr); + if (!pr->throttling.address) { ACPI_DEBUG_PRINT((ACPI_DB_INFO, "No throttling register\n")); return 0; @@ -658,18 +679,20 @@ static int acpi_processor_throttling_seq_show(struct seq_file *seq, pr->throttling.state_count - 1); seq_puts(seq, "states:\n"); - if (acpi_processor_get_throttling == acpi_processor_get_throttling_fadt) + if (pr->throttling.acpi_processor_get_throttling == + acpi_processor_get_throttling_fadt) { for (i = 0; i < pr->throttling.state_count; i++) seq_printf(seq, " %cT%d: %02d%%\n", (i == pr->throttling.state ? '*' : ' '), i, (pr->throttling.states[i].performance ? pr-> throttling.states[i].performance / 10 : 0)); - else + } else { for (i = 0; i < pr->throttling.state_count; i++) seq_printf(seq, " %cT%d: %02d%%\n", (i == pr->throttling.state ? '*' : ' '), i, (int)pr->throttling.states_tss[i]. freqpercentage); + } end: return 0; diff --git a/drivers/acpi/sleep/Makefile b/drivers/acpi/sleep/Makefile index d6c017709c8..01a993a1d08 100644 --- a/drivers/acpi/sleep/Makefile +++ b/drivers/acpi/sleep/Makefile @@ -1,5 +1,5 @@ obj-y := poweroff.o wakeup.o -obj-$(CONFIG_ACPI_SLEEP) += main.o -obj-$(CONFIG_ACPI_SLEEP_PROC_FS) += proc.o +obj-y += main.o +obj-$(CONFIG_X86) += proc.o EXTRA_CFLAGS += $(ACPI_CFLAGS) diff --git a/drivers/acpi/sleep/main.c b/drivers/acpi/sleep/main.c index 3279e72a94f..ab21357c5c7 100644 --- a/drivers/acpi/sleep/main.c +++ b/drivers/acpi/sleep/main.c @@ -34,35 +34,55 @@ static u32 acpi_suspend_states[] = { static int init_8259A_after_S1; +extern int acpi_sleep_prepare(u32 acpi_state); +extern void acpi_power_off(void); + +static u32 acpi_target_sleep_state = ACPI_STATE_S0; + +/** + * acpi_pm_set_target - Set the target system sleep state to the state + * associated with given @pm_state, if supported. + */ + +static int acpi_pm_set_target(suspend_state_t pm_state) +{ + u32 acpi_state = acpi_suspend_states[pm_state]; + int error = 0; + + if (sleep_states[acpi_state]) { + acpi_target_sleep_state = acpi_state; + } else { + printk(KERN_ERR "ACPI does not support this state: %d\n", + pm_state); + error = -ENOSYS; + } + return error; +} + /** * acpi_pm_prepare - Do preliminary suspend work. - * @pm_state: suspend state we're entering. + * @pm_state: ignored * - * Make sure we support the state. If we do, and we need it, set the - * firmware waking vector and do arch-specific nastiness to get the - * wakeup code to the waking vector. + * If necessary, set the firmware waking vector and do arch-specific + * nastiness to get the wakeup code to the waking vector. */ -extern int acpi_sleep_prepare(u32 acpi_state); -extern void acpi_power_off(void); - static int acpi_pm_prepare(suspend_state_t pm_state) { - u32 acpi_state = acpi_suspend_states[pm_state]; + int error = acpi_sleep_prepare(acpi_target_sleep_state); - if (!sleep_states[acpi_state]) { - printk("acpi_pm_prepare does not support %d \n", pm_state); - return -EPERM; - } - return acpi_sleep_prepare(acpi_state); + if (error) + acpi_target_sleep_state = ACPI_STATE_S0; + + return error; } /** * acpi_pm_enter - Actually enter a sleep state. - * @pm_state: State we're entering. + * @pm_state: ignored * - * Flush caches and go to sleep. For STR or STD, we have to call - * arch-specific assembly, which in turn call acpi_enter_sleep_state(). + * Flush caches and go to sleep. For STR we have to call arch-specific + * assembly, which in turn call acpi_enter_sleep_state(). * It's unfortunate, but it works. Please fix if you're feeling frisky. */ @@ -70,31 +90,31 @@ static int acpi_pm_enter(suspend_state_t pm_state) { acpi_status status = AE_OK; unsigned long flags = 0; - u32 acpi_state = acpi_suspend_states[pm_state]; + u32 acpi_state = acpi_target_sleep_state; ACPI_FLUSH_CPU_CACHE(); /* Do arch specific saving of state. */ - if (pm_state > PM_SUSPEND_STANDBY) { + if (acpi_state == ACPI_STATE_S3) { int error = acpi_save_state_mem(); - if (error) + + if (error) { + acpi_target_sleep_state = ACPI_STATE_S0; return error; + } } local_irq_save(flags); acpi_enable_wakeup_device(acpi_state); - switch (pm_state) { - case PM_SUSPEND_STANDBY: + switch (acpi_state) { + case ACPI_STATE_S1: barrier(); status = acpi_enter_sleep_state(acpi_state); break; - case PM_SUSPEND_MEM: + case ACPI_STATE_S3: do_suspend_lowlevel(); break; - - default: - return -EINVAL; } /* ACPI 3.0 specs (P62) says that it's the responsabilty @@ -107,12 +127,8 @@ static int acpi_pm_enter(suspend_state_t pm_state) local_irq_restore(flags); printk(KERN_DEBUG "Back to C!\n"); - /* restore processor state - * We should only be here if we're coming back from STR or STD. - * And, in the case of the latter, the memory image should have already - * been loaded from disk. - */ - if (pm_state > PM_SUSPEND_STANDBY) + /* restore processor state */ + if (acpi_state == ACPI_STATE_S3) acpi_restore_state_mem(); return ACPI_SUCCESS(status) ? 0 : -EFAULT; @@ -120,7 +136,7 @@ static int acpi_pm_enter(suspend_state_t pm_state) /** * acpi_pm_finish - Finish up suspend sequence. - * @pm_state: State we're coming out of. + * @pm_state: ignored * * This is called after we wake back up (or if entering the sleep state * failed). @@ -128,7 +144,7 @@ static int acpi_pm_enter(suspend_state_t pm_state) static int acpi_pm_finish(suspend_state_t pm_state) { - u32 acpi_state = acpi_suspend_states[pm_state]; + u32 acpi_state = acpi_target_sleep_state; acpi_leave_sleep_state(acpi_state); acpi_disable_wakeup_device(acpi_state); @@ -136,10 +152,14 @@ static int acpi_pm_finish(suspend_state_t pm_state) /* reset firmware waking vector */ acpi_set_firmware_waking_vector((acpi_physical_address) 0); + acpi_target_sleep_state = ACPI_STATE_S0; + +#ifdef CONFIG_X86 if (init_8259A_after_S1) { printk("Broken toshiba laptop -> kicking interrupts\n"); init_8259A(0); } +#endif return 0; } @@ -176,6 +196,7 @@ static int acpi_pm_state_valid(suspend_state_t pm_state) static struct pm_ops acpi_pm_ops = { .valid = acpi_pm_state_valid, + .set_target = acpi_pm_set_target, .prepare = acpi_pm_prepare, .enter = acpi_pm_enter, .finish = acpi_pm_finish, @@ -235,6 +256,81 @@ static struct hibernation_ops acpi_hibernation_ops = { }; #endif /* CONFIG_SOFTWARE_SUSPEND */ +/** + * acpi_pm_device_sleep_state - return preferred power state of ACPI device + * in the system sleep state given by %acpi_target_sleep_state + * @dev: device to examine + * @wake: if set, the device should be able to wake up the system + * @d_min_p: used to store the upper limit of allowed states range + * Return value: preferred power state of the device on success, -ENODEV on + * failure (ie. if there's no 'struct acpi_device' for @dev) + * + * Find the lowest power (highest number) ACPI device power state that + * device @dev can be in while the system is in the sleep state represented + * by %acpi_target_sleep_state. If @wake is nonzero, the device should be + * able to wake up the system from this sleep state. If @d_min_p is set, + * the highest power (lowest number) device power state of @dev allowed + * in this system sleep state is stored at the location pointed to by it. + * + * The caller must ensure that @dev is valid before using this function. + * The caller is also responsible for figuring out if the device is + * supposed to be able to wake up the system and passing this information + * via @wake. + */ + +int acpi_pm_device_sleep_state(struct device *dev, int wake, int *d_min_p) +{ + acpi_handle handle = DEVICE_ACPI_HANDLE(dev); + struct acpi_device *adev; + char acpi_method[] = "_SxD"; + unsigned long d_min, d_max; + + if (!handle || ACPI_FAILURE(acpi_bus_get_device(handle, &adev))) { + printk(KERN_ERR "ACPI handle has no context!\n"); + return -ENODEV; + } + + acpi_method[2] = '0' + acpi_target_sleep_state; + /* + * If the sleep state is S0, we will return D3, but if the device has + * _S0W, we will use the value from _S0W + */ + d_min = ACPI_STATE_D0; + d_max = ACPI_STATE_D3; + + /* + * If present, _SxD methods return the minimum D-state (highest power + * state) we can use for the corresponding S-states. Otherwise, the + * minimum D-state is D0 (ACPI 3.x). + * + * NOTE: We rely on acpi_evaluate_integer() not clobbering the integer + * provided -- that's our fault recovery, we ignore retval. + */ + if (acpi_target_sleep_state > ACPI_STATE_S0) + acpi_evaluate_integer(handle, acpi_method, NULL, &d_min); + + /* + * If _PRW says we can wake up the system from the target sleep state, + * the D-state returned by _SxD is sufficient for that (we assume a + * wakeup-aware driver if wake is set). Still, if _SxW exists + * (ACPI 3.x), it should return the maximum (lowest power) D-state that + * can wake the system. _S0W may be valid, too. + */ + if (acpi_target_sleep_state == ACPI_STATE_S0 || + (wake && adev->wakeup.state.enabled && + adev->wakeup.sleep_state <= acpi_target_sleep_state)) { + acpi_method[3] = 'W'; + acpi_evaluate_integer(handle, acpi_method, NULL, &d_max); + /* Sanity check */ + if (d_max < d_min) + d_min = d_max; + } + + if (d_min_p) + *d_min_p = d_min; + return d_max; +} + /* * Toshiba fails to preserve interrupts over S1, reinitialization * of 8259 is needed after S1 resume. diff --git a/drivers/acpi/sleep/poweroff.c b/drivers/acpi/sleep/poweroff.c index 39e40d56b03..b3f68ef0669 100644 --- a/drivers/acpi/sleep/poweroff.c +++ b/drivers/acpi/sleep/poweroff.c @@ -18,7 +18,6 @@ int acpi_sleep_prepare(u32 acpi_state) { -#ifdef CONFIG_ACPI_SLEEP /* do we have a wakeup address for S2 and S3? */ if (acpi_state == ACPI_STATE_S3) { if (!acpi_wakeup_address) { @@ -31,7 +30,6 @@ int acpi_sleep_prepare(u32 acpi_state) } ACPI_FLUSH_CPU_CACHE(); acpi_enable_wakeup_device_prep(acpi_state); -#endif acpi_gpe_sleep_prepare(acpi_state); acpi_enter_sleep_state_prep(acpi_state); return 0; diff --git a/drivers/acpi/sleep/proc.c b/drivers/acpi/sleep/proc.c index 61f1822cc35..ed58e1168ae 100644 --- a/drivers/acpi/sleep/proc.c +++ b/drivers/acpi/sleep/proc.c @@ -14,8 +14,16 @@ #include "sleep.h" #define _COMPONENT ACPI_SYSTEM_COMPONENT + +/* + * this file provides support for: + * /proc/acpi/sleep + * /proc/acpi/alarm + * /proc/acpi/wakeup + */ + ACPI_MODULE_NAME("sleep") -#ifdef CONFIG_ACPI_SLEEP_PROC_SLEEP +#ifdef CONFIG_ACPI_PROCFS static int acpi_system_sleep_seq_show(struct seq_file *seq, void *offset) { int i; @@ -68,7 +76,7 @@ acpi_system_write_sleep(struct file *file, Done: return error ? error : count; } -#endif /* CONFIG_ACPI_SLEEP_PROC_SLEEP */ +#endif /* CONFIG_ACPI_PROCFS */ #if defined(CONFIG_RTC_DRV_CMOS) || defined(CONFIG_RTC_DRV_CMOS_MODULE) /* use /sys/class/rtc/rtcX/wakealarm instead; it's not ACPI-specific */ @@ -463,7 +471,7 @@ static const struct file_operations acpi_system_wakeup_device_fops = { .release = single_release, }; -#ifdef CONFIG_ACPI_SLEEP_PROC_SLEEP +#ifdef CONFIG_ACPI_PROCFS static const struct file_operations acpi_system_sleep_fops = { .open = acpi_system_sleep_open_fs, .read = seq_read, @@ -471,7 +479,7 @@ static const struct file_operations acpi_system_sleep_fops = { .llseek = seq_lseek, .release = single_release, }; -#endif /* CONFIG_ACPI_SLEEP_PROC_SLEEP */ +#endif /* CONFIG_ACPI_PROCFS */ #ifdef HAVE_ACPI_LEGACY_ALARM static const struct file_operations acpi_system_alarm_fops = { @@ -498,14 +506,14 @@ static int __init acpi_sleep_proc_init(void) if (acpi_disabled) return 0; -#ifdef CONFIG_ACPI_SLEEP_PROC_SLEEP +#ifdef CONFIG_ACPI_PROCFS /* 'sleep' [R/W] */ entry = create_proc_entry("sleep", S_IFREG | S_IRUGO | S_IWUSR, acpi_root_dir); if (entry) entry->proc_fops = &acpi_system_sleep_fops; -#endif +#endif /* CONFIG_ACPI_PROCFS */ #ifdef HAVE_ACPI_LEGACY_ALARM /* 'alarm' [R/W] */ diff --git a/drivers/acpi/sleep/wakeup.c b/drivers/acpi/sleep/wakeup.c index fab8f2694f0..97c27ddb144 100644 --- a/drivers/acpi/sleep/wakeup.c +++ b/drivers/acpi/sleep/wakeup.c @@ -17,7 +17,6 @@ ACPI_MODULE_NAME("wakeup_devices") extern struct list_head acpi_wakeup_device_list; extern spinlock_t acpi_device_lock; -#ifdef CONFIG_ACPI_SLEEP /** * acpi_enable_wakeup_device_prep - prepare wakeup devices * @sleep_state: ACPI state @@ -180,7 +179,6 @@ static int __init acpi_wakeup_device_init(void) } late_initcall(acpi_wakeup_device_init); -#endif /* * Disable all wakeup GPEs before entering requested sleep state. diff --git a/drivers/misc/asus-laptop.c b/drivers/misc/asus-laptop.c index 63953fe0332..d0fc4fd212e 100644 --- a/drivers/misc/asus-laptop.c +++ b/drivers/misc/asus-laptop.c @@ -1072,19 +1072,16 @@ static void asus_backlight_exit(void) } #define ASUS_LED_UNREGISTER(object) \ - if(object##_led.class_dev \ - && !IS_ERR(object##_led.class_dev)) \ - led_classdev_unregister(&object##_led) + led_classdev_unregister(&object##_led) static void asus_led_exit(void) { + destroy_workqueue(led_workqueue); ASUS_LED_UNREGISTER(mled); ASUS_LED_UNREGISTER(tled); ASUS_LED_UNREGISTER(pled); ASUS_LED_UNREGISTER(rled); ASUS_LED_UNREGISTER(gled); - - destroy_workqueue(led_workqueue); } static void __exit asus_laptop_exit(void) @@ -1140,29 +1137,42 @@ static int asus_led_init(struct device *dev) rv = ASUS_LED_REGISTER(mled, dev); if (rv) - return rv; + goto out; rv = ASUS_LED_REGISTER(tled, dev); if (rv) - return rv; + goto out1; rv = ASUS_LED_REGISTER(rled, dev); if (rv) - return rv; + goto out2; rv = ASUS_LED_REGISTER(pled, dev); if (rv) - return rv; + goto out3; rv = ASUS_LED_REGISTER(gled, dev); if (rv) - return rv; + goto out4; led_workqueue = create_singlethread_workqueue("led_workqueue"); if (!led_workqueue) - return -ENOMEM; + goto out5; return 0; +out5: + rv = -ENOMEM; + ASUS_LED_UNREGISTER(gled); +out4: + ASUS_LED_UNREGISTER(pled); +out3: + ASUS_LED_UNREGISTER(rled); +out2: + ASUS_LED_UNREGISTER(tled); +out1: + ASUS_LED_UNREGISTER(mled); +out: + return rv; } static int __init asus_laptop_init(void) diff --git a/drivers/pci/pci-acpi.c b/drivers/pci/pci-acpi.c index c8062494009..67c63d1f158 100644 --- a/drivers/pci/pci-acpi.c +++ b/drivers/pci/pci-acpi.c @@ -245,16 +245,33 @@ EXPORT_SYMBOL(pci_osc_control_set); * currently we simply return _SxD, if present. */ -static int acpi_pci_choose_state(struct pci_dev *pdev, pm_message_t state) +static pci_power_t acpi_pci_choose_state(struct pci_dev *pdev, + pm_message_t state) { - /* TBD */ - - return -ENODEV; + int acpi_state; + + acpi_state = acpi_pm_device_sleep_state(&pdev->dev, + device_may_wakeup(&pdev->dev), NULL); + if (acpi_state < 0) + return PCI_POWER_ERROR; + + switch (acpi_state) { + case ACPI_STATE_D0: + return PCI_D0; + case ACPI_STATE_D1: + return PCI_D1; + case ACPI_STATE_D2: + return PCI_D2; + case ACPI_STATE_D3: + return PCI_D3hot; + } + return PCI_POWER_ERROR; } static int acpi_pci_set_power_state(struct pci_dev *dev, pci_power_t state) { acpi_handle handle = DEVICE_ACPI_HANDLE(&dev->dev); + acpi_handle tmp; static int state_conv[] = { [0] = 0, [1] = 1, @@ -266,6 +283,9 @@ static int acpi_pci_set_power_state(struct pci_dev *dev, pci_power_t state) if (!handle) return -ENODEV; + /* If the ACPI device has _EJ0, ignore the device */ + if (ACPI_SUCCESS(acpi_get_handle(handle, "_EJ0", &tmp))) + return 0; return acpi_bus_set_power(handle, acpi_state); } diff --git a/drivers/pci/pci.c b/drivers/pci/pci.c index 03fd59e80fe..1458fd69e67 100644 --- a/drivers/pci/pci.c +++ b/drivers/pci/pci.c @@ -499,7 +499,7 @@ pci_set_power_state(struct pci_dev *dev, pci_power_t state) return 0; } -int (*platform_pci_choose_state)(struct pci_dev *dev, pm_message_t state); +pci_power_t (*platform_pci_choose_state)(struct pci_dev *dev, pm_message_t state); /** * pci_choose_state - Choose the power state of a PCI device @@ -513,15 +513,15 @@ int (*platform_pci_choose_state)(struct pci_dev *dev, pm_message_t state); pci_power_t pci_choose_state(struct pci_dev *dev, pm_message_t state) { - int ret; + pci_power_t ret; if (!pci_find_capability(dev, PCI_CAP_ID_PM)) return PCI_D0; if (platform_pci_choose_state) { ret = platform_pci_choose_state(dev, state); - if (ret >= 0) - state.event = ret; + if (ret != PCI_POWER_ERROR) + return ret; } switch (state.event) { diff --git a/drivers/pci/pci.h b/drivers/pci/pci.h index 3fec13d3add..c293ba1f274 100644 --- a/drivers/pci/pci.h +++ b/drivers/pci/pci.h @@ -13,7 +13,7 @@ extern int pci_bus_alloc_resource(struct pci_bus *bus, struct resource *res, resource_size_t, resource_size_t), void *alignf_data); /* Firmware callbacks */ -extern int (*platform_pci_choose_state)(struct pci_dev *dev, pm_message_t state); +extern pci_power_t (*platform_pci_choose_state)(struct pci_dev *dev, pm_message_t state); extern int (*platform_pci_set_power_state)(struct pci_dev *dev, pci_power_t state); extern int pci_user_read_config_byte(struct pci_dev *dev, int where, u8 *val); diff --git a/drivers/pnp/driver.c b/drivers/pnp/driver.c index e161423b430..1432806451c 100644 --- a/drivers/pnp/driver.c +++ b/drivers/pnp/driver.c @@ -167,6 +167,8 @@ static int pnp_bus_suspend(struct device *dev, pm_message_t state) return error; } + if (pnp_dev->protocol && pnp_dev->protocol->suspend) + pnp_dev->protocol->suspend(pnp_dev, state); return 0; } @@ -179,6 +181,9 @@ static int pnp_bus_resume(struct device *dev) if (!pnp_drv) return 0; + if (pnp_dev->protocol && pnp_dev->protocol->resume) + pnp_dev->protocol->resume(pnp_dev); + if (!(pnp_drv->flags & PNP_DRIVER_RES_DO_NOT_CHANGE)) { error = pnp_start_dev(pnp_dev); if (error) diff --git a/drivers/pnp/pnpacpi/core.c b/drivers/pnp/pnpacpi/core.c index 0bc889144e6..fcd32ac575c 100644 --- a/drivers/pnp/pnpacpi/core.c +++ b/drivers/pnp/pnpacpi/core.c @@ -124,11 +124,25 @@ static int pnpacpi_disable_resources(struct pnp_dev *dev) return ACPI_FAILURE(status) ? -ENODEV : 0; } +static int pnpacpi_suspend(struct pnp_dev *dev, pm_message_t state) +{ + return acpi_bus_set_power((acpi_handle)dev->data, + acpi_pm_device_sleep_state(&dev->dev, + device_may_wakeup(&dev->dev), NULL)); +} + +static int pnpacpi_resume(struct pnp_dev *dev) +{ + return acpi_bus_set_power((acpi_handle)dev->data, ACPI_STATE_D0); +} + static struct pnp_protocol pnpacpi_protocol = { .name = "Plug and Play ACPI", .get = pnpacpi_get_resources, .set = pnpacpi_set_resources, .disable = pnpacpi_disable_resources, + .suspend = pnpacpi_suspend, + .resume = pnpacpi_resume, }; static int __init pnpacpi_add_device(struct acpi_device *device) |