diff options
Diffstat (limited to 'drivers')
| -rw-r--r-- | drivers/net/e1000e/defines.h | 1 | ||||
| -rw-r--r-- | drivers/net/e1000e/ich8lan.c | 125 |
2 files changed, 82 insertions, 44 deletions
diff --git a/drivers/net/e1000e/defines.h b/drivers/net/e1000e/defines.h index 4329ec34b17..c0f185beb8b 100644 --- a/drivers/net/e1000e/defines.h +++ b/drivers/net/e1000e/defines.h @@ -238,6 +238,7 @@ #define E1000_STATUS_SPEED_100 0x00000040 /* Speed 100Mb/s */ #define E1000_STATUS_SPEED_1000 0x00000080 /* Speed 1000Mb/s */ #define E1000_STATUS_LAN_INIT_DONE 0x00000200 /* Lan Init Completion by NVM */ +#define E1000_STATUS_PHYRA 0x00000400 /* PHY Reset Asserted */ #define E1000_STATUS_GIO_MASTER_ENABLE 0x00080000 /* Status of Master requests. */ /* Constants used to interpret the masked PCI-X bus speed. */ diff --git a/drivers/net/e1000e/ich8lan.c b/drivers/net/e1000e/ich8lan.c index 9e23f50fb9c..438778fef5a 100644 --- a/drivers/net/e1000e/ich8lan.c +++ b/drivers/net/e1000e/ich8lan.c @@ -694,6 +694,38 @@ static s32 e1000_hv_phy_workarounds_ich8lan(struct e1000_hw *hw) } /** + * e1000_lan_init_done_ich8lan - Check for PHY config completion + * @hw: pointer to the HW structure + * + * Check the appropriate indication the MAC has finished configuring the + * PHY after a software reset. + **/ +static void e1000_lan_init_done_ich8lan(struct e1000_hw *hw) +{ + u32 data, loop = E1000_ICH8_LAN_INIT_TIMEOUT; + + /* Wait for basic configuration completes before proceeding */ + do { + data = er32(STATUS); + data &= E1000_STATUS_LAN_INIT_DONE; + udelay(100); + } while ((!data) && --loop); + + /* + * If basic configuration is incomplete before the above loop + * count reaches 0, loading the configuration from NVM will + * leave the PHY in a bad state possibly resulting in no link. + */ + if (loop == 0) + hw_dbg(hw, "LAN_INIT_DONE not set, increase timeout\n"); + + /* Clear the Init Done bit for the next init event */ + data = er32(STATUS); + data &= ~E1000_STATUS_LAN_INIT_DONE; + ew32(STATUS, data); +} + +/** * e1000_phy_hw_reset_ich8lan - Performs a PHY reset * @hw: pointer to the HW structure * @@ -707,13 +739,15 @@ static s32 e1000_phy_hw_reset_ich8lan(struct e1000_hw *hw) u32 i; u32 data, cnf_size, cnf_base_addr, sw_cfg_mask; s32 ret_val; - u16 loop = E1000_ICH8_LAN_INIT_TIMEOUT; u16 word_addr, reg_data, reg_addr, phy_page = 0; ret_val = e1000e_phy_hw_reset_generic(hw); if (ret_val) return ret_val; + /* Allow time for h/w to get to a quiescent state after reset */ + mdelay(10); + if (hw->mac.type == e1000_pchlan) { ret_val = e1000_hv_phy_workarounds_ich8lan(hw); if (ret_val) @@ -741,26 +775,8 @@ static s32 e1000_phy_hw_reset_ich8lan(struct e1000_hw *hw) if (!(data & sw_cfg_mask)) return 0; - /* Wait for basic configuration completes before proceeding*/ - do { - data = er32(STATUS); - data &= E1000_STATUS_LAN_INIT_DONE; - udelay(100); - } while ((!data) && --loop); - - /* - * If basic configuration is incomplete before the above loop - * count reaches 0, loading the configuration from NVM will - * leave the PHY in a bad state possibly resulting in no link. - */ - if (loop == 0) { - hw_dbg(hw, "LAN_INIT_DONE not set, increase timeout\n"); - } - - /* Clear the Init Done bit for the next init event */ - data = er32(STATUS); - data &= ~E1000_STATUS_LAN_INIT_DONE; - ew32(STATUS, data); + /* Wait for basic configuration completes before proceeding */ + e1000_lan_init_done_ich8lan(hw); /* * Make sure HW does not configure LCD from PHY @@ -2143,6 +2159,12 @@ static s32 e1000_reset_hw_ich8lan(struct e1000_hw *hw) ctrl = er32(CTRL); if (!e1000_check_reset_block(hw)) { + /* Clear PHY Reset Asserted bit */ + if (hw->mac.type >= e1000_pchlan) { + u32 status = er32(STATUS); + ew32(STATUS, status & ~E1000_STATUS_PHYRA); + } + /* * PHY HW reset requires MAC CORE reset at the same * time to make sure the interface between MAC and the @@ -2156,21 +2178,24 @@ static s32 e1000_reset_hw_ich8lan(struct e1000_hw *hw) ew32(CTRL, (ctrl | E1000_CTRL_RST)); msleep(20); - if (!ret_val) { - /* release the swflag because it is not reset by - * hardware reset - */ + if (!ret_val) e1000_release_swflag_ich8lan(hw); - } - ret_val = e1000e_get_auto_rd_done(hw); - if (ret_val) { - /* - * When auto config read does not complete, do not - * return with an error. This can happen in situations - * where there is no eeprom and prevents getting link. - */ - hw_dbg(hw, "Auto Read Done did not complete\n"); + if (ctrl & E1000_CTRL_PHY_RST) + ret_val = hw->phy.ops.get_cfg_done(hw); + + if (hw->mac.type >= e1000_ich10lan) { + e1000_lan_init_done_ich8lan(hw); + } else { + ret_val = e1000e_get_auto_rd_done(hw); + if (ret_val) { + /* + * When auto config read does not complete, do not + * return with an error. This can happen in situations + * where there is no eeprom and prevents getting link. + */ + hw_dbg(hw, "Auto Read Done did not complete\n"); + } } ew32(IMC, 0xffffffff); @@ -2222,6 +2247,18 @@ static s32 e1000_init_hw_ich8lan(struct e1000_hw *hw) for (i = 0; i < mac->mta_reg_count; i++) E1000_WRITE_REG_ARRAY(hw, E1000_MTA, i, 0); + /* + * The 82578 Rx buffer will stall if wakeup is enabled in host and + * the ME. Reading the BM_WUC register will clear the host wakeup bit. + * Reset the phy after disabling host wakeup to reset the Rx buffer. + */ + if (hw->phy.type == e1000_phy_82578) { + hw->phy.ops.read_phy_reg(hw, BM_WUC, &i); + ret_val = e1000_phy_hw_reset_ich8lan(hw); + if (ret_val) + return ret_val; + } + /* Setup link and flow control */ ret_val = e1000_setup_link_ich8lan(hw); @@ -2254,16 +2291,6 @@ static s32 e1000_init_hw_ich8lan(struct e1000_hw *hw) ew32(CTRL_EXT, ctrl_ext); /* - * The 82578 Rx buffer will stall if wakeup is enabled in host and - * the ME. Reading the BM_WUC register will clear the host wakeup bit. - * Reset the phy after disabling host wakeup to reset the Rx buffer. - */ - if (hw->phy.type == e1000_phy_82578) { - e1e_rphy(hw, BM_WUC, &i); - e1000e_phy_hw_reset_generic(hw); - } - - /* * Clear all of the statistics registers (clear on read). It is * important that we do this after we have tried to establish link * because the symbol error count will increment wildly if there @@ -2850,6 +2877,16 @@ static s32 e1000_get_cfg_done_ich8lan(struct e1000_hw *hw) { u32 bank = 0; + if (hw->mac.type >= e1000_pchlan) { + u32 status = er32(STATUS); + + if (status & E1000_STATUS_PHYRA) + ew32(STATUS, status & ~E1000_STATUS_PHYRA); + else + hw_dbg(hw, + "PHY Reset Asserted not set - needs delay\n"); + } + e1000e_get_cfg_done(hw); /* If EEPROM is not marked present, init the IGP 3 PHY manually */ |