diff options
Diffstat (limited to 'include/asm-arm')
| -rw-r--r-- | include/asm-arm/arch-sa1100/irqs.h | 2 | ||||
| -rw-r--r-- | include/asm-arm/hardware/locomo.h | 19 |
2 files changed, 12 insertions, 9 deletions
diff --git a/include/asm-arm/arch-sa1100/irqs.h b/include/asm-arm/arch-sa1100/irqs.h index d7940683efb..7bf80484bb7 100644 --- a/include/asm-arm/arch-sa1100/irqs.h +++ b/include/asm-arm/arch-sa1100/irqs.h @@ -141,7 +141,7 @@ #define IRQ_LOCOMO_LT (IRQ_BOARD_END + 17) #define IRQ_LOCOMO_SPI_RFR (IRQ_BOARD_END + 18) #define IRQ_LOCOMO_SPI_RFW (IRQ_BOARD_END + 19) -#define IRQ_LOCOMO_SPI_OVRN (IRQ_BOARD_END + 20) +#define IRQ_LOCOMO_SPI_REND (IRQ_BOARD_END + 20) #define IRQ_LOCOMO_SPI_TEND (IRQ_BOARD_END + 21) /* diff --git a/include/asm-arm/hardware/locomo.h b/include/asm-arm/hardware/locomo.h index adab77780ed..fb0645de6f3 100644 --- a/include/asm-arm/hardware/locomo.h +++ b/include/asm-arm/hardware/locomo.h @@ -58,6 +58,11 @@ #define LOCOMO_SPIMD 0x00 /* SPI mode setting */ #define LOCOMO_SPICT 0x04 /* SPI mode control */ #define LOCOMO_SPIST 0x08 /* SPI status */ +#define LOCOMO_SPI_TEND (1 << 3) /* Transfer end bit */ +#define LOCOMO_SPI_REND (1 << 2) /* Receive end bit */ +#define LOCOMO_SPI_RFW (1 << 1) /* write buffer bit */ +#define LOCOMO_SPI_RFR (1) /* read buffer bit */ + #define LOCOMO_SPIIS 0x10 /* SPI interrupt status */ #define LOCOMO_SPIWE 0x14 /* SPI interrupt status write enable */ #define LOCOMO_SPIIE 0x18 /* SPI interrupt enable */ @@ -66,16 +71,12 @@ #define LOCOMO_SPIRD 0x24 /* SPI receive data read */ #define LOCOMO_SPITS 0x28 /* SPI transfer data shift */ #define LOCOMO_SPIRS 0x2C /* SPI receive data shift */ -#define LOCOMO_SPI_TEND (1 << 3) /* Transfer end bit */ -#define LOCOMO_SPI_OVRN (1 << 2) /* Over Run bit */ -#define LOCOMO_SPI_RFW (1 << 1) /* write buffer bit */ -#define LOCOMO_SPI_RFR (1) /* read buffer bit */ /* GPIO */ #define LOCOMO_GPD 0x90 /* GPIO direction */ #define LOCOMO_GPE 0x94 /* GPIO input enable */ #define LOCOMO_GPL 0x98 /* GPIO level */ -#define LOCOMO_GPO 0x9c /* GPIO out data setteing */ +#define LOCOMO_GPO 0x9c /* GPIO out data setting */ #define LOCOMO_GRIE 0xa0 /* GPIO rise detection */ #define LOCOMO_GFIE 0xa4 /* GPIO fall detection */ #define LOCOMO_GIS 0xa8 /* GPIO edge detection status */ @@ -96,6 +97,9 @@ #define LOCOMO_GPIO_DAC_SDATA LOCOMO_GPIO(10) #define LOCOMO_GPIO_DAC_SCK LOCOMO_GPIO(11) #define LOCOMO_GPIO_DAC_SLOAD LOCOMO_GPIO(12) +#define LOCOMO_GPIO_CARD_DETECT LOCOMO_GPIO(13) +#define LOCOMO_GPIO_WRITE_PROT LOCOMO_GPIO(14) +#define LOCOMO_GPIO_CARD_POWER LOCOMO_GPIO(15) /* Start the definitions of the devices. Each device has an initial * base address and a series of offsets from that base address. */ @@ -122,7 +126,7 @@ /* Audio controller */ #define LOCOMO_AUDIO 0x54 #define LOCOMO_ACC 0x00 /* Audio clock */ -#define LOCOMO_PAIF 0x7C /* PCM audio interface */ +#define LOCOMO_PAIF 0xD0 /* PCM audio interface */ /* Audio clock */ #define LOCOMO_ACC_XON 0x80 #define LOCOMO_ACC_XEN 0x40 @@ -162,7 +166,7 @@ extern struct bus_type locomo_bus_type; #define LOCOMO_DEVID_AUDIO 3 #define LOCOMO_DEVID_LED 4 #define LOCOMO_DEVID_UART 5 -#define LOCOMO_DEVID_SPI 6 +#define LOCOMO_DEVID_SPI 6 struct locomo_dev { struct device dev; @@ -204,7 +208,6 @@ int locomo_gpio_read_level(struct device *dev, unsigned int bits); int locomo_gpio_read_output(struct device *dev, unsigned int bits); void locomo_gpio_write(struct device *dev, unsigned int bits, unsigned int set); - /* M62332 control function */ void locomo_m62332_senddata(struct locomo_dev *ldev, unsigned int dac_data, int channel); |