diff options
Diffstat (limited to 'include/linux')
| -rw-r--r-- | include/linux/i2c/twl4030.h | 47 | ||||
| -rw-r--r-- | include/linux/mmc/host.h | 5 | ||||
| -rw-r--r-- | include/linux/regulator/bq24022.h | 3 | ||||
| -rw-r--r-- | include/linux/regulator/consumer.h | 6 | ||||
| -rw-r--r-- | include/linux/regulator/driver.h | 81 | ||||
| -rw-r--r-- | include/linux/regulator/fixed.h | 3 | ||||
| -rw-r--r-- | include/linux/regulator/machine.h | 12 |
7 files changed, 144 insertions, 13 deletions
diff --git a/include/linux/i2c/twl4030.h b/include/linux/i2c/twl4030.h index 8137f660a5c..0dc80ef2497 100644 --- a/include/linux/i2c/twl4030.h +++ b/include/linux/i2c/twl4030.h @@ -218,6 +218,53 @@ int twl4030_i2c_read(u8 mod_no, u8 *value, u8 reg, unsigned num_bytes); /*----------------------------------------------------------------------*/ +/* Power bus message definitions */ + +#define DEV_GRP_NULL 0x0 +#define DEV_GRP_P1 0x1 +#define DEV_GRP_P2 0x2 +#define DEV_GRP_P3 0x4 + +#define RES_GRP_RES 0x0 +#define RES_GRP_PP 0x1 +#define RES_GRP_RC 0x2 +#define RES_GRP_PP_RC 0x3 +#define RES_GRP_PR 0x4 +#define RES_GRP_PP_PR 0x5 +#define RES_GRP_RC_PR 0x6 +#define RES_GRP_ALL 0x7 + +#define RES_TYPE2_R0 0x0 + +#define RES_TYPE_ALL 0x7 + +#define RES_STATE_WRST 0xF +#define RES_STATE_ACTIVE 0xE +#define RES_STATE_SLEEP 0x8 +#define RES_STATE_OFF 0x0 + +/* + * Power Bus Message Format ... these can be sent individually by Linux, + * but are usually part of downloaded scripts that are run when various + * power events are triggered. + * + * Broadcast Message (16 Bits): + * DEV_GRP[15:13] MT[12] RES_GRP[11:9] RES_TYPE2[8:7] RES_TYPE[6:4] + * RES_STATE[3:0] + * + * Singular Message (16 Bits): + * DEV_GRP[15:13] MT[12] RES_ID[11:4] RES_STATE[3:0] + */ + +#define MSG_BROADCAST(devgrp, grp, type, type2, state) \ + ( (devgrp) << 13 | 1 << 12 | (grp) << 9 | (type2) << 7 \ + | (type) << 4 | (state)) + +#define MSG_SINGULAR(devgrp, id, state) \ + ((devgrp) << 13 | 0 << 12 | (id) << 4 | (state)) + +/*----------------------------------------------------------------------*/ + struct twl4030_bci_platform_data { int *battery_tmp_tbl; unsigned int tblsize; diff --git a/include/linux/mmc/host.h b/include/linux/mmc/host.h index 4e457256bd3..3e7615e9087 100644 --- a/include/linux/mmc/host.h +++ b/include/linux/mmc/host.h @@ -192,5 +192,10 @@ static inline void mmc_signal_sdio_irq(struct mmc_host *host) wake_up_process(host->sdio_irq_thread); } +struct regulator; + +int mmc_regulator_get_ocrmask(struct regulator *supply); +int mmc_regulator_set_ocr(struct regulator *supply, unsigned short vdd_bit); + #endif diff --git a/include/linux/regulator/bq24022.h b/include/linux/regulator/bq24022.h index e84b0a9feda..a6d014005d4 100644 --- a/include/linux/regulator/bq24022.h +++ b/include/linux/regulator/bq24022.h @@ -10,6 +10,8 @@ * */ +struct regulator_init_data; + /** * bq24022_mach_info - platform data for bq24022 * @gpio_nce: GPIO line connected to the nCE pin, used to enable / disable charging @@ -18,4 +20,5 @@ struct bq24022_mach_info { int gpio_nce; int gpio_iset2; + struct regulator_init_data *init_data; }; diff --git a/include/linux/regulator/consumer.h b/include/linux/regulator/consumer.h index 801bf77ff4e..277f4b964df 100644 --- a/include/linux/regulator/consumer.h +++ b/include/linux/regulator/consumer.h @@ -3,7 +3,7 @@ * * Copyright (C) 2007, 2008 Wolfson Microelectronics PLC. * - * Author: Liam Girdwood <lg@opensource.wolfsonmicro.com> + * Author: Liam Girdwood <lrg@slimlogic.co.uk> * * This program is free software; you can redistribute it and/or modify * it under the terms of the GNU General Public License version 2 as @@ -88,6 +88,7 @@ * FAIL Regulator output has failed. * OVER_TEMP Regulator over temp. * FORCE_DISABLE Regulator shut down by software. + * VOLTAGE_CHANGE Regulator voltage changed. * * NOTE: These events can be OR'ed together when passed into handler. */ @@ -98,6 +99,7 @@ #define REGULATOR_EVENT_FAIL 0x08 #define REGULATOR_EVENT_OVER_TEMP 0x10 #define REGULATOR_EVENT_FORCE_DISABLE 0x20 +#define REGULATOR_EVENT_VOLTAGE_CHANGE 0x40 struct regulator; @@ -140,6 +142,8 @@ int regulator_bulk_disable(int num_consumers, void regulator_bulk_free(int num_consumers, struct regulator_bulk_data *consumers); +int regulator_count_voltages(struct regulator *regulator); +int regulator_list_voltage(struct regulator *regulator, unsigned selector); int regulator_set_voltage(struct regulator *regulator, int min_uV, int max_uV); int regulator_get_voltage(struct regulator *regulator); int regulator_set_current_limit(struct regulator *regulator, diff --git a/include/linux/regulator/driver.h b/include/linux/regulator/driver.h index 2dae05705f1..4848d8dacd9 100644 --- a/include/linux/regulator/driver.h +++ b/include/linux/regulator/driver.h @@ -3,7 +3,7 @@ * * Copyright (C) 2007, 2008 Wolfson Microelectronics PLC. * - * Author: Liam Girdwood <lg@opensource.wolfsonmicro.com> + * Author: Liam Girdwood <lrg@slimlogic.co.uk> * * This program is free software; you can redistribute it and/or modify * it under the terms of the GNU General Public License version 2 as @@ -21,25 +21,38 @@ struct regulator_dev; struct regulator_init_data; +enum regulator_status { + REGULATOR_STATUS_OFF, + REGULATOR_STATUS_ON, + REGULATOR_STATUS_ERROR, + /* fast/normal/idle/standby are flavors of "on" */ + REGULATOR_STATUS_FAST, + REGULATOR_STATUS_NORMAL, + REGULATOR_STATUS_IDLE, + REGULATOR_STATUS_STANDBY, +}; + /** * struct regulator_ops - regulator operations. * - * This struct describes regulator operations which can be implemented by - * regulator chip drivers. - * - * @enable: Enable the regulator. - * @disable: Disable the regulator. + * @enable: Configure the regulator as enabled. + * @disable: Configure the regulator as disabled. * @is_enabled: Return 1 if the regulator is enabled, 0 otherwise. * * @set_voltage: Set the voltage for the regulator within the range specified. * The driver should select the voltage closest to min_uV. * @get_voltage: Return the currently configured voltage for the regulator. + * @list_voltage: Return one of the supported voltages, in microvolts; zero + * if the selector indicates a voltage that is unusable on this system; + * or negative errno. Selectors range from zero to one less than + * regulator_desc.n_voltages. Voltages may be reported in any order. * * @set_current_limit: Configure a limit for a current-limited regulator. - * @get_current_limit: Get the limit for a current-limited regulator. + * @get_current_limit: Get the configured limit for a current-limited regulator. * - * @set_mode: Set the operating mode for the regulator. - * @get_mode: Get the current operating mode for the regulator. + * @get_mode: Get the configured operating mode for the regulator. + * @get_status: Return actual (not as-configured) status of regulator, as a + * REGULATOR_STATUS value (or negative errno) * @get_optimum_mode: Get the most efficient operating mode for the regulator * when running with the specified parameters. * @@ -51,9 +64,15 @@ struct regulator_init_data; * suspended. * @set_suspend_mode: Set the operating mode for the regulator when the * system is suspended. + * + * This struct describes regulator operations which can be implemented by + * regulator chip drivers. */ struct regulator_ops { + /* enumerate supported voltages */ + int (*list_voltage) (struct regulator_dev *, unsigned selector); + /* get/set regulator voltage */ int (*set_voltage) (struct regulator_dev *, int min_uV, int max_uV); int (*get_voltage) (struct regulator_dev *); @@ -72,6 +91,13 @@ struct regulator_ops { int (*set_mode) (struct regulator_dev *, unsigned int mode); unsigned int (*get_mode) (struct regulator_dev *); + /* report regulator status ... most other accessors report + * control inputs, this reports results of combining inputs + * from Linux (and other sources) with the actual load. + * returns REGULATOR_STATUS_* or negative errno. + */ + int (*get_status)(struct regulator_dev *); + /* get most efficient regulator operating mode for load */ unsigned int (*get_optimum_mode) (struct regulator_dev *, int input_uV, int output_uV, int load_uA); @@ -106,6 +132,7 @@ enum regulator_type { * * @name: Identifying name for the regulator. * @id: Numerical identifier for the regulator. + * @n_voltages: Number of selectors available for ops.list_voltage(). * @ops: Regulator operations table. * @irq: Interrupt number for the regulator. * @type: Indicates if the regulator is a voltage or current regulator. @@ -114,14 +141,48 @@ enum regulator_type { struct regulator_desc { const char *name; int id; + unsigned n_voltages; struct regulator_ops *ops; int irq; enum regulator_type type; struct module *owner; }; +/* + * struct regulator_dev + * + * Voltage / Current regulator class device. One for each + * regulator. + * + * This should *not* be used directly by anything except the regulator + * core and notification injection (which should take the mutex and do + * no other direct access). + */ +struct regulator_dev { + struct regulator_desc *desc; + int use_count; + + /* lists we belong to */ + struct list_head list; /* list of all regulators */ + struct list_head slist; /* list of supplied regulators */ + + /* lists we own */ + struct list_head consumer_list; /* consumers we supply */ + struct list_head supply_list; /* regulators we supply */ + + struct blocking_notifier_head notifier; + struct mutex mutex; /* consumer lock */ + struct module *owner; + struct device dev; + struct regulation_constraints *constraints; + struct regulator_dev *supply; /* for tree */ + + void *reg_data; /* regulator_dev data */ +}; + struct regulator_dev *regulator_register(struct regulator_desc *regulator_desc, - struct device *dev, void *driver_data); + struct device *dev, struct regulator_init_data *init_data, + void *driver_data); void regulator_unregister(struct regulator_dev *rdev); int regulator_notifier_call_chain(struct regulator_dev *rdev, diff --git a/include/linux/regulator/fixed.h b/include/linux/regulator/fixed.h index 1387a5d2190..91b4da31f1b 100644 --- a/include/linux/regulator/fixed.h +++ b/include/linux/regulator/fixed.h @@ -14,9 +14,12 @@ #ifndef __REGULATOR_FIXED_H #define __REGULATOR_FIXED_H +struct regulator_init_data; + struct fixed_voltage_config { const char *supply_name; int microvolts; + struct regulator_init_data *init_data; }; #endif diff --git a/include/linux/regulator/machine.h b/include/linux/regulator/machine.h index 3794773b23d..bac64fa390f 100644 --- a/include/linux/regulator/machine.h +++ b/include/linux/regulator/machine.h @@ -3,7 +3,7 @@ * * Copyright (C) 2007, 2008 Wolfson Microelectronics PLC. * - * Author: Liam Girdwood <lg@opensource.wolfsonmicro.com> + * Author: Liam Girdwood <lrg@slimlogic.co.uk> * * This program is free software; you can redistribute it and/or modify * it under the terms of the GNU General Public License version 2 as @@ -73,7 +73,9 @@ struct regulator_state { * * @always_on: Set if the regulator should never be disabled. * @boot_on: Set if the regulator is enabled when the system is initially - * started. + * started. If the regulator is not enabled by the hardware or + * bootloader then it will be enabled when the constraints are + * applied. * @apply_uV: Apply the voltage constraint when initialising. * * @input_uV: Input voltage for regulator when supplied by another regulator. @@ -83,6 +85,7 @@ struct regulator_state { * @state_standby: State for regulator when system is suspended in standby * mode. * @initial_state: Suspend state to set by default. + * @initial_mode: Mode to set at startup. */ struct regulation_constraints { @@ -111,6 +114,9 @@ struct regulation_constraints { struct regulator_state state_standby; suspend_state_t initial_state; /* suspend state to set at init */ + /* mode to set on startup */ + unsigned int initial_mode; + /* constriant flags */ unsigned always_on:1; /* regulator never off when system is on */ unsigned boot_on:1; /* bootloader/firmware enabled regulator */ @@ -160,4 +166,6 @@ struct regulator_init_data { int regulator_suspend_prepare(suspend_state_t state); +void regulator_has_full_constraints(void); + #endif |