diff options
Diffstat (limited to 'include/linux')
| -rw-r--r-- | include/linux/8250_pci.h | 39 | ||||
| -rw-r--r-- | include/linux/ata.h | 2 | ||||
| -rw-r--r-- | include/linux/ethtool.h | 4 | ||||
| -rw-r--r-- | include/linux/libata.h | 8 | ||||
| -rw-r--r-- | include/linux/mii.h | 9 | ||||
| -rw-r--r-- | include/linux/mmc/host.h | 4 | ||||
| -rw-r--r-- | include/linux/mod_devicetable.h | 10 | ||||
| -rw-r--r-- | include/linux/pci_ids.h | 1 | ||||
| -rw-r--r-- | include/linux/phy.h | 377 | ||||
| -rw-r--r-- | include/linux/serialP.h | 40 |
10 files changed, 445 insertions, 49 deletions
diff --git a/include/linux/8250_pci.h b/include/linux/8250_pci.h index 5f3ab21b339..3209dd46ea7 100644 --- a/include/linux/8250_pci.h +++ b/include/linux/8250_pci.h @@ -1,2 +1,37 @@ -int pci_siig10x_fn(struct pci_dev *dev, int enable); -int pci_siig20x_fn(struct pci_dev *dev, int enable); +/* + * Definitions for PCI support. + */ +#define FL_BASE_MASK 0x0007 +#define FL_BASE0 0x0000 +#define FL_BASE1 0x0001 +#define FL_BASE2 0x0002 +#define FL_BASE3 0x0003 +#define FL_BASE4 0x0004 +#define FL_GET_BASE(x) (x & FL_BASE_MASK) + +/* Use successive BARs (PCI base address registers), + else use offset into some specified BAR */ +#define FL_BASE_BARS 0x0008 + +/* do not assign an irq */ +#define FL_NOIRQ 0x0080 + +/* Use the Base address register size to cap number of ports */ +#define FL_REGION_SZ_CAP 0x0100 + +struct pciserial_board { + unsigned int flags; + unsigned int num_ports; + unsigned int base_baud; + unsigned int uart_offset; + unsigned int reg_shift; + unsigned int first_offset; +}; + +struct serial_private; + +struct serial_private * +pciserial_init_ports(struct pci_dev *dev, struct pciserial_board *board); +void pciserial_remove_ports(struct serial_private *priv); +void pciserial_suspend_ports(struct serial_private *priv); +void pciserial_resume_ports(struct serial_private *priv); diff --git a/include/linux/ata.h b/include/linux/ata.h index ca5fcadf998..9d25e9886d6 100644 --- a/include/linux/ata.h +++ b/include/linux/ata.h @@ -108,6 +108,8 @@ enum { /* ATA device commands */ ATA_CMD_CHK_POWER = 0xE5, /* check power mode */ + ATA_CMD_STANDBY = 0xE2, /* place in standby power mode */ + ATA_CMD_IDLE = 0xE3, /* place in idle power mode */ ATA_CMD_EDD = 0x90, /* execute device diagnostic */ ATA_CMD_FLUSH = 0xE7, ATA_CMD_FLUSH_EXT = 0xEA, diff --git a/include/linux/ethtool.h b/include/linux/ethtool.h index a0ab26aab45..d7021c391b2 100644 --- a/include/linux/ethtool.h +++ b/include/linux/ethtool.h @@ -408,6 +408,8 @@ struct ethtool_ops { #define SUPPORTED_FIBRE (1 << 10) #define SUPPORTED_BNC (1 << 11) #define SUPPORTED_10000baseT_Full (1 << 12) +#define SUPPORTED_Pause (1 << 13) +#define SUPPORTED_Asym_Pause (1 << 14) /* Indicates what features are advertised by the interface. */ #define ADVERTISED_10baseT_Half (1 << 0) @@ -423,6 +425,8 @@ struct ethtool_ops { #define ADVERTISED_FIBRE (1 << 10) #define ADVERTISED_BNC (1 << 11) #define ADVERTISED_10000baseT_Full (1 << 12) +#define ADVERTISED_Pause (1 << 13) +#define ADVERTISED_Asym_Pause (1 << 14) /* The following are all involved in forcing a particular link * mode for the device for setting things. When getting the diff --git a/include/linux/libata.h b/include/linux/libata.h index 6cd9ba63563..7c09540c52b 100644 --- a/include/linux/libata.h +++ b/include/linux/libata.h @@ -113,6 +113,8 @@ enum { ATA_FLAG_MMIO = (1 << 6), /* use MMIO, not PIO */ ATA_FLAG_SATA_RESET = (1 << 7), /* use COMRESET */ ATA_FLAG_PIO_DMA = (1 << 8), /* PIO cmds via DMA */ + ATA_FLAG_NOINTR = (1 << 9), /* FIXME: Remove this once + * proper HSM is in place. */ ATA_QCFLAG_ACTIVE = (1 << 1), /* cmd not yet ack'd to scsi lyer */ ATA_QCFLAG_SG = (1 << 3), /* have s/g table? */ @@ -363,7 +365,7 @@ struct ata_port_operations { void (*host_stop) (struct ata_host_set *host_set); - void (*bmdma_stop) (struct ata_port *ap); + void (*bmdma_stop) (struct ata_queued_cmd *qc); u8 (*bmdma_status) (struct ata_port *ap); }; @@ -424,7 +426,7 @@ extern void ata_dev_id_string(u16 *id, unsigned char *s, extern void ata_dev_config(struct ata_port *ap, unsigned int i); extern void ata_bmdma_setup (struct ata_queued_cmd *qc); extern void ata_bmdma_start (struct ata_queued_cmd *qc); -extern void ata_bmdma_stop(struct ata_port *ap); +extern void ata_bmdma_stop(struct ata_queued_cmd *qc); extern u8 ata_bmdma_status(struct ata_port *ap); extern void ata_bmdma_irq_clear(struct ata_port *ap); extern void ata_qc_complete(struct ata_queued_cmd *qc, u8 drv_stat); @@ -644,7 +646,7 @@ static inline void scr_write(struct ata_port *ap, unsigned int reg, u32 val) ap->ops->scr_write(ap, reg, val); } -static inline void scr_write_flush(struct ata_port *ap, unsigned int reg, +static inline void scr_write_flush(struct ata_port *ap, unsigned int reg, u32 val) { ap->ops->scr_write(ap, reg, val); diff --git a/include/linux/mii.h b/include/linux/mii.h index 374b615ea9e..9b8d0476988 100644 --- a/include/linux/mii.h +++ b/include/linux/mii.h @@ -22,6 +22,7 @@ #define MII_EXPANSION 0x06 /* Expansion register */ #define MII_CTRL1000 0x09 /* 1000BASE-T control */ #define MII_STAT1000 0x0a /* 1000BASE-T status */ +#define MII_ESTATUS 0x0f /* Extended Status */ #define MII_DCOUNTER 0x12 /* Disconnect counter */ #define MII_FCSCOUNTER 0x13 /* False carrier counter */ #define MII_NWAYTEST 0x14 /* N-way auto-neg test reg */ @@ -54,7 +55,10 @@ #define BMSR_ANEGCAPABLE 0x0008 /* Able to do auto-negotiation */ #define BMSR_RFAULT 0x0010 /* Remote fault detected */ #define BMSR_ANEGCOMPLETE 0x0020 /* Auto-negotiation complete */ -#define BMSR_RESV 0x07c0 /* Unused... */ +#define BMSR_RESV 0x00c0 /* Unused... */ +#define BMSR_ESTATEN 0x0100 /* Extended Status in R15 */ +#define BMSR_100FULL2 0x0200 /* Can do 100BASE-T2 HDX */ +#define BMSR_100HALF2 0x0400 /* Can do 100BASE-T2 FDX */ #define BMSR_10HALF 0x0800 /* Can do 10mbps, half-duplex */ #define BMSR_10FULL 0x1000 /* Can do 10mbps, full-duplex */ #define BMSR_100HALF 0x2000 /* Can do 100mbps, half-duplex */ @@ -114,6 +118,9 @@ #define EXPANSION_MFAULTS 0x0010 /* Multiple faults detected */ #define EXPANSION_RESV 0xffe0 /* Unused... */ +#define ESTATUS_1000_TFULL 0x2000 /* Can do 1000BT Full */ +#define ESTATUS_1000_THALF 0x1000 /* Can do 1000BT Half */ + /* N-way test register. */ #define NWAYTEST_RESV1 0x00ff /* Unused... */ #define NWAYTEST_LOOPBACK 0x0100 /* Enable loopback for N-way */ diff --git a/include/linux/mmc/host.h b/include/linux/mmc/host.h index f90f674eb3b..9a0893f3249 100644 --- a/include/linux/mmc/host.h +++ b/include/linux/mmc/host.h @@ -63,11 +63,12 @@ struct device; struct mmc_host { struct device *dev; + struct class_device class_dev; + int index; struct mmc_host_ops *ops; unsigned int f_min; unsigned int f_max; u32 ocr_avail; - char host_name[8]; /* host specific block data */ unsigned int max_seg_size; /* see blk_queue_max_segment_size */ @@ -97,6 +98,7 @@ extern void mmc_free_host(struct mmc_host *); #define mmc_priv(x) ((void *)((x) + 1)) #define mmc_dev(x) ((x)->dev) +#define mmc_hostname(x) ((x)->class_dev.class_id) extern int mmc_suspend_host(struct mmc_host *, pm_message_t); extern int mmc_resume_host(struct mmc_host *); diff --git a/include/linux/mod_devicetable.h b/include/linux/mod_devicetable.h index dce53ac1625..97bbccdbcca 100644 --- a/include/linux/mod_devicetable.h +++ b/include/linux/mod_devicetable.h @@ -33,7 +33,8 @@ struct ieee1394_device_id { __u32 model_id; __u32 specifier_id; __u32 version; - kernel_ulong_t driver_data; + kernel_ulong_t driver_data + __attribute__((aligned(sizeof(kernel_ulong_t)))); }; @@ -182,7 +183,11 @@ struct of_device_id char name[32]; char type[32]; char compatible[128]; +#if __KERNEL__ void *data; +#else + kernel_ulong_t data; +#endif }; @@ -208,7 +213,8 @@ struct pcmcia_device_id { #ifdef __KERNEL__ const char * prod_id[4]; #else - kernel_ulong_t prod_id[4]; + kernel_ulong_t prod_id[4] + __attribute__((aligned(sizeof(kernel_ulong_t)))); #endif /* not matched against */ diff --git a/include/linux/pci_ids.h b/include/linux/pci_ids.h index 927ed487630..499a5325f67 100644 --- a/include/linux/pci_ids.h +++ b/include/linux/pci_ids.h @@ -1249,6 +1249,7 @@ #define PCI_DEVICE_ID_NVIDIA_NFORCE_MCP51_SATA 0x0266 #define PCI_DEVICE_ID_NVIDIA_NFORCE_MCP51_SATA2 0x0267 #define PCI_DEVICE_ID_NVIDIA_NFORCE_MCP55_IDE 0x036E +#define PCI_DEVICE_ID_NVIDIA_NFORCE_MCP55_SATA 0x036F #define PCI_DEVICE_ID_NVIDIA_NVENET_12 0x0268 #define PCI_DEVICE_ID_NVIDIA_NVENET_13 0x0269 #define PCI_DEVICE_ID_NVIDIA_MCP51_AUDIO 0x026B diff --git a/include/linux/phy.h b/include/linux/phy.h new file mode 100644 index 00000000000..72cb67b66e0 --- /dev/null +++ b/include/linux/phy.h @@ -0,0 +1,377 @@ +/* + * include/linux/phy.h + * + * Framework and drivers for configuring and reading different PHYs + * Based on code in sungem_phy.c and gianfar_phy.c + * + * Author: Andy Fleming + * + * Copyright (c) 2004 Freescale Semiconductor, Inc. + * + * This program is free software; you can redistribute it and/or modify it + * under the terms of the GNU General Public License as published by the + * Free Software Foundation; either version 2 of the License, or (at your + * option) any later version. + * + */ + +#ifndef __PHY_H +#define __PHY_H + +#include <linux/spinlock.h> +#include <linux/device.h> + +#define PHY_BASIC_FEATURES (SUPPORTED_10baseT_Half | \ + SUPPORTED_10baseT_Full | \ + SUPPORTED_100baseT_Half | \ + SUPPORTED_100baseT_Full | \ + SUPPORTED_Autoneg | \ + SUPPORTED_TP | \ + SUPPORTED_MII) + +#define PHY_GBIT_FEATURES (PHY_BASIC_FEATURES | \ + SUPPORTED_1000baseT_Half | \ + SUPPORTED_1000baseT_Full) + +/* Set phydev->irq to PHY_POLL if interrupts are not supported, + * or not desired for this PHY. Set to PHY_IGNORE_INTERRUPT if + * the attached driver handles the interrupt + */ +#define PHY_POLL -1 +#define PHY_IGNORE_INTERRUPT -2 + +#define PHY_HAS_INTERRUPT 0x00000001 +#define PHY_HAS_MAGICANEG 0x00000002 + +#define MII_BUS_MAX 4 + + +#define PHY_INIT_TIMEOUT 100000 +#define PHY_STATE_TIME 1 +#define PHY_FORCE_TIMEOUT 10 +#define PHY_AN_TIMEOUT 10 + +#define PHY_MAX_ADDR 32 + +/* The Bus class for PHYs. Devices which provide access to + * PHYs should register using this structure */ +struct mii_bus { + const char *name; + int id; + void *priv; + int (*read)(struct mii_bus *bus, int phy_id, int regnum); + int (*write)(struct mii_bus *bus, int phy_id, int regnum, u16 val); + int (*reset)(struct mii_bus *bus); + + /* A lock to ensure that only one thing can read/write + * the MDIO bus at a time */ + spinlock_t mdio_lock; + + struct device *dev; + + /* list of all PHYs on bus */ + struct phy_device *phy_map[PHY_MAX_ADDR]; + + /* Pointer to an array of interrupts, each PHY's + * interrupt at the index matching its address */ + int *irq; +}; + +#define PHY_INTERRUPT_DISABLED 0x0 +#define PHY_INTERRUPT_ENABLED 0x80000000 + +/* PHY state machine states: + * + * DOWN: PHY device and driver are not ready for anything. probe + * should be called if and only if the PHY is in this state, + * given that the PHY device exists. + * - PHY driver probe function will, depending on the PHY, set + * the state to STARTING or READY + * + * STARTING: PHY device is coming up, and the ethernet driver is + * not ready. PHY drivers may set this in the probe function. + * If they do, they are responsible for making sure the state is + * eventually set to indicate whether the PHY is UP or READY, + * depending on the state when the PHY is done starting up. + * - PHY driver will set the state to READY + * - start will set the state to PENDING + * + * READY: PHY is ready to send and receive packets, but the + * controller is not. By default, PHYs which do not implement + * probe will be set to this state by phy_probe(). If the PHY + * driver knows the PHY is ready, and the PHY state is STARTING, + * then it sets this STATE. + * - start will set the state to UP + * + * PENDING: PHY device is coming up, but the ethernet driver is + * ready. phy_start will set this state if the PHY state is + * STARTING. + * - PHY driver will set the state to UP when the PHY is ready + * + * UP: The PHY and attached device are ready to do work. + * Interrupts should be started here. + * - timer moves to AN + * + * AN: The PHY is currently negotiating the link state. Link is + * therefore down for now. phy_timer will set this state when it + * detects the state is UP. config_aneg will set this state + * whenever called with phydev->autoneg set to AUTONEG_ENABLE. + * - If autonegotiation finishes, but there's no link, it sets + * the state to NOLINK. + * - If aneg finishes with link, it sets the state to RUNNING, + * and calls adjust_link + * - If autonegotiation did not finish after an arbitrary amount + * of time, autonegotiation should be tried again if the PHY + * supports "magic" autonegotiation (back to AN) + * - If it didn't finish, and no magic_aneg, move to FORCING. + * + * NOLINK: PHY is up, but not currently plugged in. + * - If the timer notes that the link comes back, we move to RUNNING + * - config_aneg moves to AN + * - phy_stop moves to HALTED + * + * FORCING: PHY is being configured with forced settings + * - if link is up, move to RUNNING + * - If link is down, we drop to the next highest setting, and + * retry (FORCING) after a timeout + * - phy_stop moves to HALTED + * + * RUNNING: PHY is currently up, running, and possibly sending + * and/or receiving packets + * - timer will set CHANGELINK if we're polling (this ensures the + * link state is polled every other cycle of this state machine, + * which makes it every other second) + * - irq will set CHANGELINK + * - config_aneg will set AN + * - phy_stop moves to HALTED + * + * CHANGELINK: PHY experienced a change in link state + * - timer moves to RUNNING if link + * - timer moves to NOLINK if the link is down + * - phy_stop moves to HALTED + * + * HALTED: PHY is up, but no polling or interrupts are done. Or + * PHY is in an error state. + * + * - phy_start moves to RESUMING + * + * RESUMING: PHY was halted, but now wants to run again. + * - If we are forcing, or aneg is done, timer moves to RUNNING + * - If aneg is not done, timer moves to AN + * - phy_stop moves to HALTED + */ +enum phy_state { + PHY_DOWN=0, + PHY_STARTING, + PHY_READY, + PHY_PENDING, + PHY_UP, + PHY_AN, + PHY_RUNNING, + PHY_NOLINK, + PHY_FORCING, + PHY_CHANGELINK, + PHY_HALTED, + PHY_RESUMING +}; + +/* phy_device: An instance of a PHY + * + * drv: Pointer to the driver for this PHY instance + * bus: Pointer to the bus this PHY is on + * dev: driver model device structure for this PHY + * phy_id: UID for this device found during discovery + * state: state of the PHY for management purposes + * dev_flags: Device-specific flags used by the PHY driver. + * addr: Bus address of PHY + * link_timeout: The number of timer firings to wait before the + * giving up on the current attempt at acquiring a link + * irq: IRQ number of the PHY's interrupt (-1 if none) + * phy_timer: The timer for handling the state machine + * phy_queue: A work_queue for the interrupt + * attached_dev: The attached enet driver's device instance ptr + * adjust_link: Callback for the enet controller to respond to + * changes in the link state. + * adjust_state: Callback for the enet driver to respond to + * changes in the state machine. + * + * speed, duplex, pause, supported, advertising, and + * autoneg are used like in mii_if_info + * + * interrupts currently only supports enabled or disabled, + * but could be changed in the future to support enabling + * and disabling specific interrupts + * + * Contains some infrastructure for polling and interrupt + * handling, as well as handling shifts in PHY hardware state + */ +struct phy_device { + /* Information about the PHY type */ + /* And management functions */ + struct phy_driver *drv; + + struct mii_bus *bus; + + struct device dev; + + u32 phy_id; + + enum phy_state state; + + u32 dev_flags; + + /* Bus address of the PHY (0-32) */ + int addr; + + /* forced speed & duplex (no autoneg) + * partner speed & duplex & pause (autoneg) + */ + int speed; + int duplex; + int pause; + int asym_pause; + + /* The most recently read link state */ + int link; + + /* Enabled Interrupts */ + u32 interrupts; + + /* Union of PHY and Attached devices' supported modes */ + /* See mii.h for more info */ + u32 supported; + u32 advertising; + + int autoneg; + + int link_timeout; + + /* Interrupt number for this PHY + * -1 means no interrupt */ + int irq; + + /* private data pointer */ + /* For use by PHYs to maintain extra state */ + void *priv; + + /* Interrupt and Polling infrastructure */ + struct work_struct phy_queue; + struct timer_list phy_timer; + + spinlock_t lock; + + struct net_device *attached_dev; + + void (*adjust_link)(struct net_device *dev); + + void (*adjust_state)(struct net_device *dev); +}; +#define to_phy_device(d) container_of(d, struct phy_device, dev) + +/* struct phy_driver: Driver structure for a particular PHY type + * + * phy_id: The result of reading the UID registers of this PHY + * type, and ANDing them with the phy_id_mask. This driver + * only works for PHYs with IDs which match this field + * name: The friendly name of this PHY type + * phy_id_mask: Defines the important bits of the phy_id + * features: A list of features (speed, duplex, etc) supported + * by this PHY + * flags: A bitfield defining certain other features this PHY + * supports (like interrupts) + * + * The drivers must implement config_aneg and read_status. All + * other functions are optional. Note that none of these + * functions should be called from interrupt time. The goal is + * for the bus read/write functions to be able to block when the + * bus transaction is happening, and be freed up by an interrupt + * (The MPC85xx has this ability, though it is not currently + * supported in the driver). + */ +struct phy_driver { + u32 phy_id; + char *name; + unsigned int phy_id_mask; + u32 features; + u32 flags; + + /* Called to initialize the PHY, + * including after a reset */ + int (*config_init)(struct phy_device *phydev); + + /* Called during discovery. Used to set + * up device-specific structures, if any */ + int (*probe)(struct phy_device *phydev); + + /* PHY Power Management */ + int (*suspend)(struct phy_device *phydev); + int (*resume)(struct phy_device *phydev); + + /* Configures the advertisement and resets + * autonegotiation if phydev->autoneg is on, + * forces the speed to the current settings in phydev + * if phydev->autoneg is off */ + int (*config_aneg)(struct phy_device *phydev); + + /* Determines the negotiated speed and duplex */ + int (*read_status)(struct phy_device *phydev); + + /* Clears any pending interrupts */ + int (*ack_interrupt)(struct phy_device *phydev); + + /* Enables or disables interrupts */ + int (*config_intr)(struct phy_device *phydev); + + /* Clears up any memory if needed */ + void (*remove)(struct phy_device *phydev); + + struct device_driver driver; +}; +#define to_phy_driver(d) container_of(d, struct phy_driver, driver) + +int phy_read(struct phy_device *phydev, u16 regnum); +int phy_write(struct phy_device *phydev, u16 regnum, u16 val); +struct phy_device* get_phy_device(struct mii_bus *bus, int addr); +int phy_clear_interrupt(struct phy_device *phydev); +int phy_config_interrupt(struct phy_device *phydev, u32 interrupts); +struct phy_device * phy_attach(struct net_device *dev, + const char *phy_id, u32 flags); +struct phy_device * phy_connect(struct net_device *dev, const char *phy_id, + void (*handler)(struct net_device *), u32 flags); +void phy_disconnect(struct phy_device *phydev); +void phy_detach(struct phy_device *phydev); +void phy_start(struct phy_device *phydev); +void phy_stop(struct phy_device *phydev); +int phy_start_aneg(struct phy_device *phydev); + +int mdiobus_register(struct mii_bus *bus); +void mdiobus_unregister(struct mii_bus *bus); +void phy_sanitize_settings(struct phy_device *phydev); +int phy_stop_interrupts(struct phy_device *phydev); + +static inline int phy_read_status(struct phy_device *phydev) { + return phydev->drv->read_status(phydev); +} + +int genphy_config_advert(struct phy_device *phydev); +int genphy_setup_forced(struct phy_device *phydev); +int genphy_restart_aneg(struct phy_device *phydev); +int genphy_config_aneg(struct phy_device *phydev); +int genphy_update_link(struct phy_device *phydev); +int genphy_read_status(struct phy_device *phydev); +void phy_driver_unregister(struct phy_driver *drv); +int phy_driver_register(struct phy_driver *new_driver); +void phy_prepare_link(struct phy_device *phydev, + void (*adjust_link)(struct net_device *)); +void phy_start_machine(struct phy_device *phydev, + void (*handler)(struct net_device *)); +void phy_stop_machine(struct phy_device *phydev); +int phy_ethtool_sset(struct phy_device *phydev, struct ethtool_cmd *cmd); +int phy_ethtool_gset(struct phy_device *phydev, struct ethtool_cmd *cmd); +int phy_mii_ioctl(struct phy_device *phydev, + struct mii_ioctl_data *mii_data, int cmd); +int phy_start_interrupts(struct phy_device *phydev); +void phy_print_status(struct phy_device *phydev); + +extern struct bus_type mdio_bus_type; +#endif /* __PHY_H */ diff --git a/include/linux/serialP.h b/include/linux/serialP.h index 2b2f35a64d7..2b9e6b9554d 100644 --- a/include/linux/serialP.h +++ b/include/linux/serialP.h @@ -140,44 +140,4 @@ struct rs_multiport_struct { #define ALPHA_KLUDGE_MCR 0 #endif -/* - * Definitions for PCI support. - */ -#define SPCI_FL_BASE_MASK 0x0007 -#define SPCI_FL_BASE0 0x0000 -#define SPCI_FL_BASE1 0x0001 -#define SPCI_FL_BASE2 0x0002 -#define SPCI_FL_BASE3 0x0003 -#define SPCI_FL_BASE4 0x0004 -#define SPCI_FL_GET_BASE(x) (x & SPCI_FL_BASE_MASK) - -#define SPCI_FL_IRQ_MASK (0x0007 << 4) -#define SPCI_FL_IRQBASE0 (0x0000 << 4) -#define SPCI_FL_IRQBASE1 (0x0001 << 4) -#define SPCI_FL_IRQBASE2 (0x0002 << 4) -#define SPCI_FL_IRQBASE3 (0x0003 << 4) -#define SPCI_FL_IRQBASE4 (0x0004 << 4) -#define SPCI_FL_GET_IRQBASE(x) ((x & SPCI_FL_IRQ_MASK) >> 4) - -/* Use successive BARs (PCI base address registers), - else use offset into some specified BAR */ -#define SPCI_FL_BASE_TABLE 0x0100 - -/* Use successive entries in the irq resource table */ -#define SPCI_FL_IRQ_TABLE 0x0200 - -/* Use the irq resource table instead of dev->irq */ -#define SPCI_FL_IRQRESOURCE 0x0400 - -/* Use the Base address register size to cap number of ports */ -#define SPCI_FL_REGION_SZ_CAP 0x0800 - -/* Do not use irq sharing for this device */ -#define SPCI_FL_NO_SHIRQ 0x1000 - -/* This is a PNP device */ -#define SPCI_FL_ISPNP 0x2000 - -#define SPCI_FL_PNPDEFAULT (SPCI_FL_IRQRESOURCE|SPCI_FL_ISPNP) - #endif /* _LINUX_SERIAL_H */ |