aboutsummaryrefslogtreecommitdiff
path: root/include/linux
diff options
context:
space:
mode:
Diffstat (limited to 'include/linux')
-rw-r--r--include/linux/8250_pci.h39
-rw-r--r--include/linux/ata.h2
-rw-r--r--include/linux/ethtool.h4
-rw-r--r--include/linux/libata.h8
-rw-r--r--include/linux/mii.h9
-rw-r--r--include/linux/mmc/host.h4
-rw-r--r--include/linux/pci_ids.h1
-rw-r--r--include/linux/phy.h377
-rw-r--r--include/linux/serialP.h40
9 files changed, 437 insertions, 47 deletions
diff --git a/include/linux/8250_pci.h b/include/linux/8250_pci.h
index 5f3ab21b339..3209dd46ea7 100644
--- a/include/linux/8250_pci.h
+++ b/include/linux/8250_pci.h
@@ -1,2 +1,37 @@
-int pci_siig10x_fn(struct pci_dev *dev, int enable);
-int pci_siig20x_fn(struct pci_dev *dev, int enable);
+/*
+ * Definitions for PCI support.
+ */
+#define FL_BASE_MASK 0x0007
+#define FL_BASE0 0x0000
+#define FL_BASE1 0x0001
+#define FL_BASE2 0x0002
+#define FL_BASE3 0x0003
+#define FL_BASE4 0x0004
+#define FL_GET_BASE(x) (x & FL_BASE_MASK)
+
+/* Use successive BARs (PCI base address registers),
+ else use offset into some specified BAR */
+#define FL_BASE_BARS 0x0008
+
+/* do not assign an irq */
+#define FL_NOIRQ 0x0080
+
+/* Use the Base address register size to cap number of ports */
+#define FL_REGION_SZ_CAP 0x0100
+
+struct pciserial_board {
+ unsigned int flags;
+ unsigned int num_ports;
+ unsigned int base_baud;
+ unsigned int uart_offset;
+ unsigned int reg_shift;
+ unsigned int first_offset;
+};
+
+struct serial_private;
+
+struct serial_private *
+pciserial_init_ports(struct pci_dev *dev, struct pciserial_board *board);
+void pciserial_remove_ports(struct serial_private *priv);
+void pciserial_suspend_ports(struct serial_private *priv);
+void pciserial_resume_ports(struct serial_private *priv);
diff --git a/include/linux/ata.h b/include/linux/ata.h
index ca5fcadf998..9d25e9886d6 100644
--- a/include/linux/ata.h
+++ b/include/linux/ata.h
@@ -108,6 +108,8 @@ enum {
/* ATA device commands */
ATA_CMD_CHK_POWER = 0xE5, /* check power mode */
+ ATA_CMD_STANDBY = 0xE2, /* place in standby power mode */
+ ATA_CMD_IDLE = 0xE3, /* place in idle power mode */
ATA_CMD_EDD = 0x90, /* execute device diagnostic */
ATA_CMD_FLUSH = 0xE7,
ATA_CMD_FLUSH_EXT = 0xEA,
diff --git a/include/linux/ethtool.h b/include/linux/ethtool.h
index a0ab26aab45..d7021c391b2 100644
--- a/include/linux/ethtool.h
+++ b/include/linux/ethtool.h
@@ -408,6 +408,8 @@ struct ethtool_ops {
#define SUPPORTED_FIBRE (1 << 10)
#define SUPPORTED_BNC (1 << 11)
#define SUPPORTED_10000baseT_Full (1 << 12)
+#define SUPPORTED_Pause (1 << 13)
+#define SUPPORTED_Asym_Pause (1 << 14)
/* Indicates what features are advertised by the interface. */
#define ADVERTISED_10baseT_Half (1 << 0)
@@ -423,6 +425,8 @@ struct ethtool_ops {
#define ADVERTISED_FIBRE (1 << 10)
#define ADVERTISED_BNC (1 << 11)
#define ADVERTISED_10000baseT_Full (1 << 12)
+#define ADVERTISED_Pause (1 << 13)
+#define ADVERTISED_Asym_Pause (1 << 14)
/* The following are all involved in forcing a particular link
* mode for the device for setting things. When getting the
diff --git a/include/linux/libata.h b/include/linux/libata.h
index 6cd9ba63563..7c09540c52b 100644
--- a/include/linux/libata.h
+++ b/include/linux/libata.h
@@ -113,6 +113,8 @@ enum {
ATA_FLAG_MMIO = (1 << 6), /* use MMIO, not PIO */
ATA_FLAG_SATA_RESET = (1 << 7), /* use COMRESET */
ATA_FLAG_PIO_DMA = (1 << 8), /* PIO cmds via DMA */
+ ATA_FLAG_NOINTR = (1 << 9), /* FIXME: Remove this once
+ * proper HSM is in place. */
ATA_QCFLAG_ACTIVE = (1 << 1), /* cmd not yet ack'd to scsi lyer */
ATA_QCFLAG_SG = (1 << 3), /* have s/g table? */
@@ -363,7 +365,7 @@ struct ata_port_operations {
void (*host_stop) (struct ata_host_set *host_set);
- void (*bmdma_stop) (struct ata_port *ap);
+ void (*bmdma_stop) (struct ata_queued_cmd *qc);
u8 (*bmdma_status) (struct ata_port *ap);
};
@@ -424,7 +426,7 @@ extern void ata_dev_id_string(u16 *id, unsigned char *s,
extern void ata_dev_config(struct ata_port *ap, unsigned int i);
extern void ata_bmdma_setup (struct ata_queued_cmd *qc);
extern void ata_bmdma_start (struct ata_queued_cmd *qc);
-extern void ata_bmdma_stop(struct ata_port *ap);
+extern void ata_bmdma_stop(struct ata_queued_cmd *qc);
extern u8 ata_bmdma_status(struct ata_port *ap);
extern void ata_bmdma_irq_clear(struct ata_port *ap);
extern void ata_qc_complete(struct ata_queued_cmd *qc, u8 drv_stat);
@@ -644,7 +646,7 @@ static inline void scr_write(struct ata_port *ap, unsigned int reg, u32 val)
ap->ops->scr_write(ap, reg, val);
}
-static inline void scr_write_flush(struct ata_port *ap, unsigned int reg,
+static inline void scr_write_flush(struct ata_port *ap, unsigned int reg,
u32 val)
{
ap->ops->scr_write(ap, reg, val);
diff --git a/include/linux/mii.h b/include/linux/mii.h
index 374b615ea9e..9b8d0476988 100644
--- a/include/linux/mii.h
+++ b/include/linux/mii.h
@@ -22,6 +22,7 @@
#define MII_EXPANSION 0x06 /* Expansion register */
#define MII_CTRL1000 0x09 /* 1000BASE-T control */
#define MII_STAT1000 0x0a /* 1000BASE-T status */
+#define MII_ESTATUS 0x0f /* Extended Status */
#define MII_DCOUNTER 0x12 /* Disconnect counter */
#define MII_FCSCOUNTER 0x13 /* False carrier counter */
#define MII_NWAYTEST 0x14 /* N-way auto-neg test reg */
@@ -54,7 +55,10 @@
#define BMSR_ANEGCAPABLE 0x0008 /* Able to do auto-negotiation */
#define BMSR_RFAULT 0x0010 /* Remote fault detected */
#define BMSR_ANEGCOMPLETE 0x0020 /* Auto-negotiation complete */
-#define BMSR_RESV 0x07c0 /* Unused... */
+#define BMSR_RESV 0x00c0 /* Unused... */
+#define BMSR_ESTATEN 0x0100 /* Extended Status in R15 */
+#define BMSR_100FULL2 0x0200 /* Can do 100BASE-T2 HDX */
+#define BMSR_100HALF2 0x0400 /* Can do 100BASE-T2 FDX */
#define BMSR_10HALF 0x0800 /* Can do 10mbps, half-duplex */
#define BMSR_10FULL 0x1000 /* Can do 10mbps, full-duplex */
#define BMSR_100HALF 0x2000 /* Can do 100mbps, half-duplex */
@@ -114,6 +118,9 @@
#define EXPANSION_MFAULTS 0x0010 /* Multiple faults detected */
#define EXPANSION_RESV 0xffe0 /* Unused... */
+#define ESTATUS_1000_TFULL 0x2000 /* Can do 1000BT Full */
+#define ESTATUS_1000_THALF 0x1000 /* Can do 1000BT Half */
+
/* N-way test register. */
#define NWAYTEST_RESV1 0x00ff /* Unused... */
#define NWAYTEST_LOOPBACK 0x0100 /* Enable loopback for N-way */
diff --git a/include/linux/mmc/host.h b/include/linux/mmc/host.h
index f90f674eb3b..9a0893f3249 100644
--- a/include/linux/mmc/host.h
+++ b/include/linux/mmc/host.h
@@ -63,11 +63,12 @@ struct device;
struct mmc_host {
struct device *dev;
+ struct class_device class_dev;
+ int index;
struct mmc_host_ops *ops;
unsigned int f_min;
unsigned int f_max;
u32 ocr_avail;
- char host_name[8];
/* host specific block data */
unsigned int max_seg_size; /* see blk_queue_max_segment_size */
@@ -97,6 +98,7 @@ extern void mmc_free_host(struct mmc_host *);
#define mmc_priv(x) ((void *)((x) + 1))
#define mmc_dev(x) ((x)->dev)
+#define mmc_hostname(x) ((x)->class_dev.class_id)
extern int mmc_suspend_host(struct mmc_host *, pm_message_t);
extern int mmc_resume_host(struct mmc_host *);
diff --git a/include/linux/pci_ids.h b/include/linux/pci_ids.h
index 927ed487630..499a5325f67 100644
--- a/include/linux/pci_ids.h
+++ b/include/linux/pci_ids.h
@@ -1249,6 +1249,7 @@
#define PCI_DEVICE_ID_NVIDIA_NFORCE_MCP51_SATA 0x0266
#define PCI_DEVICE_ID_NVIDIA_NFORCE_MCP51_SATA2 0x0267
#define PCI_DEVICE_ID_NVIDIA_NFORCE_MCP55_IDE 0x036E
+#define PCI_DEVICE_ID_NVIDIA_NFORCE_MCP55_SATA 0x036F
#define PCI_DEVICE_ID_NVIDIA_NVENET_12 0x0268
#define PCI_DEVICE_ID_NVIDIA_NVENET_13 0x0269
#define PCI_DEVICE_ID_NVIDIA_MCP51_AUDIO 0x026B
diff --git a/include/linux/phy.h b/include/linux/phy.h
new file mode 100644
index 00000000000..72cb67b66e0
--- /dev/null
+++ b/include/linux/phy.h
@@ -0,0 +1,377 @@
+/*
+ * include/linux/phy.h
+ *
+ * Framework and drivers for configuring and reading different PHYs
+ * Based on code in sungem_phy.c and gianfar_phy.c
+ *
+ * Author: Andy Fleming
+ *
+ * Copyright (c) 2004 Freescale Semiconductor, Inc.
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License as published by the
+ * Free Software Foundation; either version 2 of the License, or (at your
+ * option) any later version.
+ *
+ */
+
+#ifndef __PHY_H
+#define __PHY_H
+
+#include <linux/spinlock.h>
+#include <linux/device.h>
+
+#define PHY_BASIC_FEATURES (SUPPORTED_10baseT_Half | \
+ SUPPORTED_10baseT_Full | \
+ SUPPORTED_100baseT_Half | \
+ SUPPORTED_100baseT_Full | \
+ SUPPORTED_Autoneg | \
+ SUPPORTED_TP | \
+ SUPPORTED_MII)
+
+#define PHY_GBIT_FEATURES (PHY_BASIC_FEATURES | \
+ SUPPORTED_1000baseT_Half | \
+ SUPPORTED_1000baseT_Full)
+
+/* Set phydev->irq to PHY_POLL if interrupts are not supported,
+ * or not desired for this PHY. Set to PHY_IGNORE_INTERRUPT if
+ * the attached driver handles the interrupt
+ */
+#define PHY_POLL -1
+#define PHY_IGNORE_INTERRUPT -2
+
+#define PHY_HAS_INTERRUPT 0x00000001
+#define PHY_HAS_MAGICANEG 0x00000002
+
+#define MII_BUS_MAX 4
+
+
+#define PHY_INIT_TIMEOUT 100000
+#define PHY_STATE_TIME 1
+#define PHY_FORCE_TIMEOUT 10
+#define PHY_AN_TIMEOUT 10
+
+#define PHY_MAX_ADDR 32
+
+/* The Bus class for PHYs. Devices which provide access to
+ * PHYs should register using this structure */
+struct mii_bus {
+ const char *name;
+ int id;
+ void *priv;
+ int (*read)(struct mii_bus *bus, int phy_id, int regnum);
+ int (*write)(struct mii_bus *bus, int phy_id, int regnum, u16 val);
+ int (*reset)(struct mii_bus *bus);
+
+ /* A lock to ensure that only one thing can read/write
+ * the MDIO bus at a time */
+ spinlock_t mdio_lock;
+
+ struct device *dev;
+
+ /* list of all PHYs on bus */
+ struct phy_device *phy_map[PHY_MAX_ADDR];
+
+ /* Pointer to an array of interrupts, each PHY's
+ * interrupt at the index matching its address */
+ int *irq;
+};
+
+#define PHY_INTERRUPT_DISABLED 0x0
+#define PHY_INTERRUPT_ENABLED 0x80000000
+
+/* PHY state machine states:
+ *
+ * DOWN: PHY device and driver are not ready for anything. probe
+ * should be called if and only if the PHY is in this state,
+ * given that the PHY device exists.
+ * - PHY driver probe function will, depending on the PHY, set
+ * the state to STARTING or READY
+ *
+ * STARTING: PHY device is coming up, and the ethernet driver is
+ * not ready. PHY drivers may set this in the probe function.
+ * If they do, they are responsible for making sure the state is
+ * eventually set to indicate whether the PHY is UP or READY,
+ * depending on the state when the PHY is done starting up.
+ * - PHY driver will set the state to READY
+ * - start will set the state to PENDING
+ *
+ * READY: PHY is ready to send and receive packets, but the
+ * controller is not. By default, PHYs which do not implement
+ * probe will be set to this state by phy_probe(). If the PHY
+ * driver knows the PHY is ready, and the PHY state is STARTING,
+ * then it sets this STATE.
+ * - start will set the state to UP
+ *
+ * PENDING: PHY device is coming up, but the ethernet driver is
+ * ready. phy_start will set this state if the PHY state is
+ * STARTING.
+ * - PHY driver will set the state to UP when the PHY is ready
+ *
+ * UP: The PHY and attached device are ready to do work.
+ * Interrupts should be started here.
+ * - timer moves to AN
+ *
+ * AN: The PHY is currently negotiating the link state. Link is
+ * therefore down for now. phy_timer will set this state when it
+ * detects the state is UP. config_aneg will set this state
+ * whenever called with phydev->autoneg set to AUTONEG_ENABLE.
+ * - If autonegotiation finishes, but there's no link, it sets
+ * the state to NOLINK.
+ * - If aneg finishes with link, it sets the state to RUNNING,
+ * and calls adjust_link
+ * - If autonegotiation did not finish after an arbitrary amount
+ * of time, autonegotiation should be tried again if the PHY
+ * supports "magic" autonegotiation (back to AN)
+ * - If it didn't finish, and no magic_aneg, move to FORCING.
+ *
+ * NOLINK: PHY is up, but not currently plugged in.
+ * - If the timer notes that the link comes back, we move to RUNNING
+ * - config_aneg moves to AN
+ * - phy_stop moves to HALTED
+ *
+ * FORCING: PHY is being configured with forced settings
+ * - if link is up, move to RUNNING
+ * - If link is down, we drop to the next highest setting, and
+ * retry (FORCING) after a timeout
+ * - phy_stop moves to HALTED
+ *
+ * RUNNING: PHY is currently up, running, and possibly sending
+ * and/or receiving packets
+ * - timer will set CHANGELINK if we're polling (this ensures the
+ * link state is polled every other cycle of this state machine,
+ * which makes it every other second)
+ * - irq will set CHANGELINK
+ * - config_aneg will set AN
+ * - phy_stop moves to HALTED
+ *
+ * CHANGELINK: PHY experienced a change in link state
+ * - timer moves to RUNNING if link
+ * - timer moves to NOLINK if the link is down
+ * - phy_stop moves to HALTED
+ *
+ * HALTED: PHY is up, but no polling or interrupts are done. Or
+ * PHY is in an error state.
+ *
+ * - phy_start moves to RESUMING
+ *
+ * RESUMING: PHY was halted, but now wants to run again.
+ * - If we are forcing, or aneg is done, timer moves to RUNNING
+ * - If aneg is not done, timer moves to AN
+ * - phy_stop moves to HALTED
+ */
+enum phy_state {
+ PHY_DOWN=0,
+ PHY_STARTING,
+ PHY_READY,
+ PHY_PENDING,
+ PHY_UP,
+ PHY_AN,
+ PHY_RUNNING,
+ PHY_NOLINK,
+ PHY_FORCING,
+ PHY_CHANGELINK,
+ PHY_HALTED,
+ PHY_RESUMING
+};
+
+/* phy_device: An instance of a PHY
+ *
+ * drv: Pointer to the driver for this PHY instance
+ * bus: Pointer to the bus this PHY is on
+ * dev: driver model device structure for this PHY
+ * phy_id: UID for this device found during discovery
+ * state: state of the PHY for management purposes
+ * dev_flags: Device-specific flags used by the PHY driver.
+ * addr: Bus address of PHY
+ * link_timeout: The number of timer firings to wait before the
+ * giving up on the current attempt at acquiring a link
+ * irq: IRQ number of the PHY's interrupt (-1 if none)
+ * phy_timer: The timer for handling the state machine
+ * phy_queue: A work_queue for the interrupt
+ * attached_dev: The attached enet driver's device instance ptr
+ * adjust_link: Callback for the enet controller to respond to
+ * changes in the link state.
+ * adjust_state: Callback for the enet driver to respond to
+ * changes in the state machine.
+ *
+ * speed, duplex, pause, supported, advertising, and
+ * autoneg are used like in mii_if_info
+ *
+ * interrupts currently only supports enabled or disabled,
+ * but could be changed in the future to support enabling
+ * and disabling specific interrupts
+ *
+ * Contains some infrastructure for polling and interrupt
+ * handling, as well as handling shifts in PHY hardware state
+ */
+struct phy_device {
+ /* Information about the PHY type */
+ /* And management functions */
+ struct phy_driver *drv;
+
+ struct mii_bus *bus;
+
+ struct device dev;
+
+ u32 phy_id;
+
+ enum phy_state state;
+
+ u32 dev_flags;
+
+ /* Bus address of the PHY (0-32) */
+ int addr;
+
+ /* forced speed & duplex (no autoneg)
+ * partner speed & duplex & pause (autoneg)
+ */
+ int speed;
+ int duplex;
+ int pause;
+ int asym_pause;
+
+ /* The most recently read link state */
+ int link;
+
+ /* Enabled Interrupts */
+ u32 interrupts;
+
+ /* Union of PHY and Attached devices' supported modes */
+ /* See mii.h for more info */
+ u32 supported;
+ u32 advertising;
+
+ int autoneg;
+
+ int link_timeout;
+
+ /* Interrupt number for this PHY
+ * -1 means no interrupt */
+ int irq;
+
+ /* private data pointer */
+ /* For use by PHYs to maintain extra state */
+ void *priv;
+
+ /* Interrupt and Polling infrastructure */
+ struct work_struct phy_queue;
+ struct timer_list phy_timer;
+
+ spinlock_t lock;
+
+ struct net_device *attached_dev;
+
+ void (*adjust_link)(struct net_device *dev);
+
+ void (*adjust_state)(struct net_device *dev);
+};
+#define to_phy_device(d) container_of(d, struct phy_device, dev)
+
+/* struct phy_driver: Driver structure for a particular PHY type
+ *
+ * phy_id: The result of reading the UID registers of this PHY
+ * type, and ANDing them with the phy_id_mask. This driver
+ * only works for PHYs with IDs which match this field
+ * name: The friendly name of this PHY type
+ * phy_id_mask: Defines the important bits of the phy_id
+ * features: A list of features (speed, duplex, etc) supported
+ * by this PHY
+ * flags: A bitfield defining certain other features this PHY
+ * supports (like interrupts)
+ *
+ * The drivers must implement config_aneg and read_status. All
+ * other functions are optional. Note that none of these
+ * functions should be called from interrupt time. The goal is
+ * for the bus read/write functions to be able to block when the
+ * bus transaction is happening, and be freed up by an interrupt
+ * (The MPC85xx has this ability, though it is not currently
+ * supported in the driver).
+ */
+struct phy_driver {
+ u32 phy_id;
+ char *name;
+ unsigned int phy_id_mask;
+ u32 features;
+ u32 flags;
+
+ /* Called to initialize the PHY,
+ * including after a reset */
+ int (*config_init)(struct phy_device *phydev);
+
+ /* Called during discovery. Used to set
+ * up device-specific structures, if any */
+ int (*probe)(struct phy_device *phydev);
+
+ /* PHY Power Management */
+ int (*suspend)(struct phy_device *phydev);
+ int (*resume)(struct phy_device *phydev);
+
+ /* Configures the advertisement and resets
+ * autonegotiation if phydev->autoneg is on,
+ * forces the speed to the current settings in phydev
+ * if phydev->autoneg is off */
+ int (*config_aneg)(struct phy_device *phydev);
+
+ /* Determines the negotiated speed and duplex */
+ int (*read_status)(struct phy_device *phydev);
+
+ /* Clears any pending interrupts */
+ int (*ack_interrupt)(struct phy_device *phydev);
+
+ /* Enables or disables interrupts */
+ int (*config_intr)(struct phy_device *phydev);
+
+ /* Clears up any memory if needed */
+ void (*remove)(struct phy_device *phydev);
+
+ struct device_driver driver;
+};
+#define to_phy_driver(d) container_of(d, struct phy_driver, driver)
+
+int phy_read(struct phy_device *phydev, u16 regnum);
+int phy_write(struct phy_device *phydev, u16 regnum, u16 val);
+struct phy_device* get_phy_device(struct mii_bus *bus, int addr);
+int phy_clear_interrupt(struct phy_device *phydev);
+int phy_config_interrupt(struct phy_device *phydev, u32 interrupts);
+struct phy_device * phy_attach(struct net_device *dev,
+ const char *phy_id, u32 flags);
+struct phy_device * phy_connect(struct net_device *dev, const char *phy_id,
+ void (*handler)(struct net_device *), u32 flags);
+void phy_disconnect(struct phy_device *phydev);
+void phy_detach(struct phy_device *phydev);
+void phy_start(struct phy_device *phydev);
+void phy_stop(struct phy_device *phydev);
+int phy_start_aneg(struct phy_device *phydev);
+
+int mdiobus_register(struct mii_bus *bus);
+void mdiobus_unregister(struct mii_bus *bus);
+void phy_sanitize_settings(struct phy_device *phydev);
+int phy_stop_interrupts(struct phy_device *phydev);
+
+static inline int phy_read_status(struct phy_device *phydev) {
+ return phydev->drv->read_status(phydev);
+}
+
+int genphy_config_advert(struct phy_device *phydev);
+int genphy_setup_forced(struct phy_device *phydev);
+int genphy_restart_aneg(struct phy_device *phydev);
+int genphy_config_aneg(struct phy_device *phydev);
+int genphy_update_link(struct phy_device *phydev);
+int genphy_read_status(struct phy_device *phydev);
+void phy_driver_unregister(struct phy_driver *drv);
+int phy_driver_register(struct phy_driver *new_driver);
+void phy_prepare_link(struct phy_device *phydev,
+ void (*adjust_link)(struct net_device *));
+void phy_start_machine(struct phy_device *phydev,
+ void (*handler)(struct net_device *));
+void phy_stop_machine(struct phy_device *phydev);
+int phy_ethtool_sset(struct phy_device *phydev, struct ethtool_cmd *cmd);
+int phy_ethtool_gset(struct phy_device *phydev, struct ethtool_cmd *cmd);
+int phy_mii_ioctl(struct phy_device *phydev,
+ struct mii_ioctl_data *mii_data, int cmd);
+int phy_start_interrupts(struct phy_device *phydev);
+void phy_print_status(struct phy_device *phydev);
+
+extern struct bus_type mdio_bus_type;
+#endif /* __PHY_H */
diff --git a/include/linux/serialP.h b/include/linux/serialP.h
index 2b2f35a64d7..2b9e6b9554d 100644
--- a/include/linux/serialP.h
+++ b/include/linux/serialP.h
@@ -140,44 +140,4 @@ struct rs_multiport_struct {
#define ALPHA_KLUDGE_MCR 0
#endif
-/*
- * Definitions for PCI support.
- */
-#define SPCI_FL_BASE_MASK 0x0007
-#define SPCI_FL_BASE0 0x0000
-#define SPCI_FL_BASE1 0x0001
-#define SPCI_FL_BASE2 0x0002
-#define SPCI_FL_BASE3 0x0003
-#define SPCI_FL_BASE4 0x0004
-#define SPCI_FL_GET_BASE(x) (x & SPCI_FL_BASE_MASK)
-
-#define SPCI_FL_IRQ_MASK (0x0007 << 4)
-#define SPCI_FL_IRQBASE0 (0x0000 << 4)
-#define SPCI_FL_IRQBASE1 (0x0001 << 4)
-#define SPCI_FL_IRQBASE2 (0x0002 << 4)
-#define SPCI_FL_IRQBASE3 (0x0003 << 4)
-#define SPCI_FL_IRQBASE4 (0x0004 << 4)
-#define SPCI_FL_GET_IRQBASE(x) ((x & SPCI_FL_IRQ_MASK) >> 4)
-
-/* Use successive BARs (PCI base address registers),
- else use offset into some specified BAR */
-#define SPCI_FL_BASE_TABLE 0x0100
-
-/* Use successive entries in the irq resource table */
-#define SPCI_FL_IRQ_TABLE 0x0200
-
-/* Use the irq resource table instead of dev->irq */
-#define SPCI_FL_IRQRESOURCE 0x0400
-
-/* Use the Base address register size to cap number of ports */
-#define SPCI_FL_REGION_SZ_CAP 0x0800
-
-/* Do not use irq sharing for this device */
-#define SPCI_FL_NO_SHIRQ 0x1000
-
-/* This is a PNP device */
-#define SPCI_FL_ISPNP 0x2000
-
-#define SPCI_FL_PNPDEFAULT (SPCI_FL_IRQRESOURCE|SPCI_FL_ISPNP)
-
#endif /* _LINUX_SERIAL_H */
generated by cgit v1.2.3 (git 2.25.1) at 2024-12-22 15:52:10 +0000