diff options
Diffstat (limited to 'include/linux')
-rw-r--r-- | include/linux/8250_pci.h | 39 | ||||
-rw-r--r-- | include/linux/serialP.h | 40 |
2 files changed, 37 insertions, 42 deletions
diff --git a/include/linux/8250_pci.h b/include/linux/8250_pci.h index 5f3ab21b339..3209dd46ea7 100644 --- a/include/linux/8250_pci.h +++ b/include/linux/8250_pci.h @@ -1,2 +1,37 @@ -int pci_siig10x_fn(struct pci_dev *dev, int enable); -int pci_siig20x_fn(struct pci_dev *dev, int enable); +/* + * Definitions for PCI support. + */ +#define FL_BASE_MASK 0x0007 +#define FL_BASE0 0x0000 +#define FL_BASE1 0x0001 +#define FL_BASE2 0x0002 +#define FL_BASE3 0x0003 +#define FL_BASE4 0x0004 +#define FL_GET_BASE(x) (x & FL_BASE_MASK) + +/* Use successive BARs (PCI base address registers), + else use offset into some specified BAR */ +#define FL_BASE_BARS 0x0008 + +/* do not assign an irq */ +#define FL_NOIRQ 0x0080 + +/* Use the Base address register size to cap number of ports */ +#define FL_REGION_SZ_CAP 0x0100 + +struct pciserial_board { + unsigned int flags; + unsigned int num_ports; + unsigned int base_baud; + unsigned int uart_offset; + unsigned int reg_shift; + unsigned int first_offset; +}; + +struct serial_private; + +struct serial_private * +pciserial_init_ports(struct pci_dev *dev, struct pciserial_board *board); +void pciserial_remove_ports(struct serial_private *priv); +void pciserial_suspend_ports(struct serial_private *priv); +void pciserial_resume_ports(struct serial_private *priv); diff --git a/include/linux/serialP.h b/include/linux/serialP.h index 2b2f35a64d7..2b9e6b9554d 100644 --- a/include/linux/serialP.h +++ b/include/linux/serialP.h @@ -140,44 +140,4 @@ struct rs_multiport_struct { #define ALPHA_KLUDGE_MCR 0 #endif -/* - * Definitions for PCI support. - */ -#define SPCI_FL_BASE_MASK 0x0007 -#define SPCI_FL_BASE0 0x0000 -#define SPCI_FL_BASE1 0x0001 -#define SPCI_FL_BASE2 0x0002 -#define SPCI_FL_BASE3 0x0003 -#define SPCI_FL_BASE4 0x0004 -#define SPCI_FL_GET_BASE(x) (x & SPCI_FL_BASE_MASK) - -#define SPCI_FL_IRQ_MASK (0x0007 << 4) -#define SPCI_FL_IRQBASE0 (0x0000 << 4) -#define SPCI_FL_IRQBASE1 (0x0001 << 4) -#define SPCI_FL_IRQBASE2 (0x0002 << 4) -#define SPCI_FL_IRQBASE3 (0x0003 << 4) -#define SPCI_FL_IRQBASE4 (0x0004 << 4) -#define SPCI_FL_GET_IRQBASE(x) ((x & SPCI_FL_IRQ_MASK) >> 4) - -/* Use successive BARs (PCI base address registers), - else use offset into some specified BAR */ -#define SPCI_FL_BASE_TABLE 0x0100 - -/* Use successive entries in the irq resource table */ -#define SPCI_FL_IRQ_TABLE 0x0200 - -/* Use the irq resource table instead of dev->irq */ -#define SPCI_FL_IRQRESOURCE 0x0400 - -/* Use the Base address register size to cap number of ports */ -#define SPCI_FL_REGION_SZ_CAP 0x0800 - -/* Do not use irq sharing for this device */ -#define SPCI_FL_NO_SHIRQ 0x1000 - -/* This is a PNP device */ -#define SPCI_FL_ISPNP 0x2000 - -#define SPCI_FL_PNPDEFAULT (SPCI_FL_IRQRESOURCE|SPCI_FL_ISPNP) - #endif /* _LINUX_SERIAL_H */ |