diff options
Diffstat (limited to 'include/net/mac80211.h')
| -rw-r--r-- | include/net/mac80211.h | 31 |
1 files changed, 14 insertions, 17 deletions
diff --git a/include/net/mac80211.h b/include/net/mac80211.h index 4dd3d93e196..ff137fd7714 100644 --- a/include/net/mac80211.h +++ b/include/net/mac80211.h @@ -177,9 +177,10 @@ enum ieee80211_bss_change { * @aid: association ID number, valid only when @assoc is true * @use_cts_prot: use CTS protection * @use_short_preamble: use 802.11b short preamble + * @dtim_period: num of beacons before the next DTIM, for PSM * @timestamp: beacon timestamp * @beacon_int: beacon interval - * @assoc_capability: capabbilities taken from assoc resp + * @assoc_capability: capabilities taken from assoc resp * @assoc_ht: association in HT mode * @ht_conf: ht capabilities * @ht_bss_conf: ht extended capabilities @@ -191,6 +192,7 @@ struct ieee80211_bss_conf { /* erp related data */ bool use_cts_prot; bool use_short_preamble; + u8 dtim_period; u16 beacon_int; u16 assoc_capability; u64 timestamp; @@ -206,8 +208,6 @@ struct ieee80211_bss_conf { * These flags are used with the @flags member of &ieee80211_tx_info. * * @IEEE80211_TX_CTL_REQ_TX_STATUS: request TX status callback for this frame. - * @IEEE80211_TX_CTL_DO_NOT_ENCRYPT: send this frame without encryption; - * e.g., for EAPOL frame * @IEEE80211_TX_CTL_USE_RTS_CTS: use RTS-CTS before sending frame * @IEEE80211_TX_CTL_USE_CTS_PROTECT: use CTS protection for the frame (e.g., * for combined 802.11g / 802.11b networks) @@ -220,7 +220,6 @@ struct ieee80211_bss_conf { * @IEEE80211_TX_CTL_SHORT_PREAMBLE: TBD * @IEEE80211_TX_CTL_LONG_RETRY_LIMIT: this frame should be send using the * through set_retry_limit configured long retry value - * @IEEE80211_TX_CTL_EAPOL_FRAME: internal to mac80211 * @IEEE80211_TX_CTL_SEND_AFTER_DTIM: send this frame after DTIM beacon * @IEEE80211_TX_CTL_AMPDU: this frame should be sent as part of an A-MPDU * @IEEE80211_TX_CTL_OFDM_HT: this frame can be sent in HT OFDM rates. number @@ -253,7 +252,6 @@ struct ieee80211_bss_conf { */ enum mac80211_tx_control_flags { IEEE80211_TX_CTL_REQ_TX_STATUS = BIT(0), - IEEE80211_TX_CTL_DO_NOT_ENCRYPT = BIT(1), IEEE80211_TX_CTL_USE_RTS_CTS = BIT(2), IEEE80211_TX_CTL_USE_CTS_PROTECT = BIT(3), IEEE80211_TX_CTL_NO_ACK = BIT(4), @@ -263,7 +261,6 @@ enum mac80211_tx_control_flags { IEEE80211_TX_CTL_FIRST_FRAGMENT = BIT(8), IEEE80211_TX_CTL_SHORT_PREAMBLE = BIT(9), IEEE80211_TX_CTL_LONG_RETRY_LIMIT = BIT(10), - IEEE80211_TX_CTL_EAPOL_FRAME = BIT(11), IEEE80211_TX_CTL_SEND_AFTER_DTIM = BIT(12), IEEE80211_TX_CTL_AMPDU = BIT(13), IEEE80211_TX_CTL_OFDM_HT = BIT(14), @@ -323,7 +320,6 @@ struct ieee80211_tx_info { struct ieee80211_vif *vif; struct ieee80211_key_conf *hw_key; unsigned long jiffies; - int ifindex; u16 aid; s8 rts_cts_rate_idx, alt_retry_rate_idx; u8 retry_limit; @@ -436,6 +432,7 @@ enum ieee80211_conf_flags { * @radio_enabled: when zero, driver is required to switch off the radio. * TODO make a flag * @beacon_int: beacon interval (TODO make interface config) + * @listen_interval: listen interval in units of beacon interval * @flags: configuration flags defined above * @power_level: requested transmit power (in dBm) * @max_antenna_gain: maximum antenna gain (in dBi) @@ -450,6 +447,7 @@ struct ieee80211_conf { int radio_enabled; int beacon_int; + u16 listen_interval; u32 flags; int power_level; int max_antenna_gain; @@ -710,10 +708,7 @@ enum ieee80211_tkip_key_type { * rely on the host system for such buffering. This option is used * to configure the IEEE 802.11 upper layer to buffer broadcast and * multicast frames when there are power saving stations so that - * the driver can fetch them with ieee80211_get_buffered_bc(). Note - * that not setting this flag works properly only when the - * %IEEE80211_HW_HOST_GEN_BEACON_TEMPLATE is also not set because - * otherwise the stack will not know when the DTIM beacon was sent. + * the driver can fetch them with ieee80211_get_buffered_bc(). * * @IEEE80211_HW_2GHZ_SHORT_SLOT_INCAPABLE: * Hardware is not capable of short slot operation on the 2.4 GHz band. @@ -746,7 +741,6 @@ enum ieee80211_tkip_key_type { * Measurement, Channel Switch, Quieting, TPC */ enum ieee80211_hw_flags { - IEEE80211_HW_HOST_GEN_BEACON_TEMPLATE = 1<<0, IEEE80211_HW_RX_INCLUDES_FCS = 1<<1, IEEE80211_HW_HOST_BROADCAST_PS_BUFFERING = 1<<2, IEEE80211_HW_2GHZ_SHORT_SLOT_INCAPABLE = 1<<3, @@ -792,6 +786,9 @@ enum ieee80211_hw_flags { * @max_signal: Maximum value for signal (rssi) in RX information, used * only when @IEEE80211_HW_SIGNAL_UNSPEC or @IEEE80211_HW_SIGNAL_DB * + * @max_listen_interval: max listen interval in units of beacon interval + * that HW supports + * * @queues: number of available hardware transmit queues for * data packets. WMM/QoS requires at least four, these * queues need to have configurable access parameters. @@ -819,7 +816,9 @@ struct ieee80211_hw { unsigned int extra_tx_headroom; int channel_change_time; int vif_data_size; - u16 queues, ampdu_queues; + u16 queues; + u16 ampdu_queues; + u16 max_listen_interval; s8 max_signal; }; @@ -1097,10 +1096,8 @@ enum ieee80211_ampdu_mlme_action { * See the section "Frame filtering" for more information. * This callback must be implemented and atomic. * - * @set_tim: Set TIM bit. If the hardware/firmware takes care of beacon - * generation (that is, %IEEE80211_HW_HOST_GEN_BEACON_TEMPLATE is set) - * mac80211 calls this function when a TIM bit must be set or cleared - * for a given AID. Must be atomic. + * @set_tim: Set TIM bit. mac80211 calls this function when a TIM bit + * must be set or cleared for a given AID. Must be atomic. * * @set_key: See the section "Hardware crypto acceleration" * This callback can sleep, and is only called between add_interface |