| Age | Commit message (Collapse) | Author |
|---|
|
Create arch/x86_64/vdso/.gitignore and put vdso.lds into it.
Signed-off-by: Pete Zaitcev <zaitcev@redhat.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Some people writing boot loaders seem to falsely belief the 32bit zero page is a
stable interface for out of tree code like the real mode boot protocol. Add a comment
clarifying that is not true.
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
The Averatec 2370 and some other Turion laptop BIOS seems to program the
ENABLE_C1E MSR inconsistently between cores. This confuses the lapic
use heuristics because when C1E is enabled anywhere it seems to affect
the complete chip.
Use a global flag instead of a per cpu flag to handle this.
If any CPU has C1E enabled disabled lapic use.
Thanks to Cal Peake for debugging.
Cc: tglx@linutronix.de
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
It's CONFIG_X86_MCE, not CONFIG_MCE.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
VT is very picky about when it can enter execution.
Get all segments setup and get LDT and TR into valid state to allow
VT execution under VMware and KVM (untested).
This makes the boot decompression run under VT, which makes it several
orders of magnitude faster on 64-bit Intel hardware.
Before, I was seeing times up to a minute or more to decompress a 1.3MB kernel
on a very fast box.
Signed-off-by: Zachary Amsden <zach@vmware.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Commit 19d36ccdc34f5ed444f8a6af0cbfdb6790eb1177 "x86: Fix alternatives
and kprobes to remap write-protected kernel text" uses code which is
being patched for patching.
In particular, paravirt_ops does patching in two stages: first it
calls paravirt_ops.patch, then it fills any remaining instructions
with nop_out(). nop_out calls text_poke() which calls
lookup_address() which calls pgd_val() (aka paravirt_ops.pgd_val):
that call site is one of the places we patch.
If we always do patching as one single call to text_poke(), we only
need make sure we're not patching the memcpy in text_poke itself.
This means the prototype to paravirt_ops.patch needs to change, to
marshal the new code into a buffer rather than patching in place as it
does now. It also means all patching goes through text_poke(), which
is known to be safe (apply_alternatives is also changed to make a
single patch).
AK: fix compilation on x86-64 (bad rusty!)
AK: fix boot on x86-64 (sigh)
AK: merged with other patches
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
It turns out CLFLUSH support is still not complete; we
flush the wrong pages. Again disable it for the release.
Noticed by Jan Beulich who then also noticed a stupid typo later.
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
gcc currently doesn't support attributes on types, so we can't use it
function pointers. This avoids some warnings on a gcc 4.3 build.
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Current code assumed that devices were directly connected to a Calgary
bridge, as it tried to get the iommu table directly from the parent bus
controller.
When we have another bridge between the Calgary/CalIOC2 bridge and the
device we should look upwards until we get to the top (Calgary/CalIOC2
bridge), where the iommu table resides.
Signed-off-by: Murillo Fernandes Bernardes <mfb@br.ibm.com>
Signed-off-by: Muli Ben-Yehuda <muli@il.ibm.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Some broken devices have been discovered to require %al/%ax/%eax registers
for MMIO config space accesses. Modify mmconfig.c to use these registers
explicitly (rather than modify the global readb/writeb/etc inlines).
AK: also changed i386 to always use eax
AK: moved change to extended space probing to different patch
AK: reworked with inlines according to Linus' requirements.
AK: improve comments.
Signed-off-by: dean gaudet <dean@arctic.org>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
There are some parts of include/asm-generic/pgtable.h that are relevant to
the non-mmu architectures. To make it easier to include this from them I
would like to ifdef the relevant parts.
Without this there is a handful of functions that are referenced in here
that are not defined on many non-mmu architectures. They could be defined
out of course, as an alternative approach.
Cc: David Howells <dhowells@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
This patch finishes the i386 and x86-64 ->sysdata conversion and hopefully
also fixes Riku's and Andy's observed bugs. It is based on Yinghai Lu's
and Andy Whitcroft's patches (thanks!) with some changes:
- introduce pci_scan_bus_with_sysdata() and use it instead of
pci_scan_bus() where appropriate. pci_scan_bus_with_sysdata() will
allocate the sysdata structure and then call pci_scan_bus().
- always allocate pci_sysdata dynamically. The whole point of this
sysdata work is to make it easy to do root-bus specific things
(e.g., support PCI domains and IOMMU's). I dislike using a default
struct pci_sysdata in some places and a dynamically allocated
pci_sysdata elsewhere - the potential for someone indavertantly
changing the default structure is too high.
- this patch only makes the minimal changes necessary, i.e., the NUMA node is
always initialized to -1. Patches to do the right thing with regards
to the NUMA node can build on top of this (either add a 'node'
parameter to pci_scan_bus_with_sysdata() or just update the node
when it becomes known).
The patch was compile tested with various configurations (e.g., NUMAQ,
VISWS) and run-time tested on i386 and x86-64. Unfortunately none of my
machines exhibited the bugs so caveat emptor.
Andy, could you please see if this fixes the NUMA issues you've seen?
Riku, does this fix "pci=noacpi" on your laptop?
Signed-off-by: Muli Ben-Yehuda <muli@il.ibm.com>
Cc: Yinghai Lu <yhlu.kernel@gmail.com>
Cc: Andi Kleen <ak@suse.de>
Cc: Chuck Ebbert <cebbert@redhat.com>
Cc: <riku.seppala@kymp.net>
Cc: Andy Whitcroft <apw@shadowen.org>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Minor docbook error since argument name in comment doesn't match function
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
This code corrects the usage of the request_irq() routine.
Signed-off-by: Jay Estabrook <jay.estabrook@hp.com>
Signed-off-by: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Cc: Richard Henderson <rth@twiddle.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Files using bits from paravirt.h should explicitly include it rather than
relying on it being pulled in by something else.
Signed-off-by: Jes Sorensen <jes@sgi.com>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
gcc-4.2 is a lot more picky about its symbol handling. EXPORT_SYMBOL no
longer works on symbols that are undefined or defined with static scope.
For example, with CONFIG_PROFILE off, I see:
kernel/profile.c:206: error: __ksymtab_profile_event_unregister causes a section type conflict
kernel/profile.c:205: error: __ksymtab_profile_event_register causes a section type conflict
This patch moves the EXPORTs inside the #ifdef CONFIG_PROFILE, so we
only try to export symbols that are defined.
Also, in kernel/kprobes.c there's an EXPORT_SYMBOL_GPL() for
jprobes_return, which if CONFIG_JPROBES is undefined is a static
inline and gives the same error.
And in drivers/acpi/resources/rsxface.c, there's an
ACPI_EXPORT_SYMBOPL() for a static symbol. If it's static, it's not
accessible from outside the compilation unit, so should bot be exported.
These three changes allow building a zx1_defconfig kernel with gcc 4.2
on IA64.
[akpm@linux-foundation.org: export jpobe_return properly]
Signed-off-by: Peter Chubb <peterc@gelato.unsw.edu.au>
Cc: Prasanna S Panchamukhi <prasanna@in.ibm.com>
Cc: Ananth N Mavinakayanahalli <ananth@in.ibm.com>
Cc: Anil S Keshavamurthy <anil.s.keshavamurthy@intel.com>
Cc: "Luck, Tony" <tony.luck@intel.com>
Cc: Len Brown <lenb@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
I find a function(clockevents_unregister_notifier) which is not called by
anything in tree.
Signed-off-by: Miao Xie <miaox@cn.fujitsu.com>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Git rid of "warning: passing arg 2 of `access_ok' makes pointer from integer
without a cast" reported on SH ... most architectures use macros in that
test, SH uses inlined functions.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
scripts/kconfig/conf -d arch/cris/Kconfig
arch/cris/Kconfig:183: can't open file "drivers/cdrom/Kconfig"
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Cc: Mikael Starvik <starvik@axis.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
synchronize_idle() sounds like an interesting function, but we don't
actually have it, so don't prototype it. Introduced in commit
9b06e818985d139fd9e82c28297f7744e1b484e1, in 2005.
Signed-off-by: Josh Triplett <josh@kernel.org>
Acked-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Add missing "const" qualifiers to the print_hex_dump_bytes() library routines.
(akpm: rumoured to fix some compile warning somewhere)
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Cc: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
sh:
drivers/mtd/mtdchar.c: In function `mtd_mmap':
drivers/mtd/mtdchar.c:817: error: dereferencing pointer to incomplete type
drivers/mtd/mtdchar.c:817: error: `VM_SHARED' undeclared (first use in this function)
drivers/mtd/mtdchar.c:817: error: (Each undeclared identifier is reported only once
Cc: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Patch c5c34d4862e18ef07c1276d233507f540fb5a532 (tty: flush flip buffer on
ldisc input queue flush) introduces a race condition which can lead to memory
leaks.
The problem can be triggered when tcflush() is called when data are being
pushed to the line discipline driver by flush_to_ldisc().
flush_to_ldisc() releases tty->buf.lock when calling the line discipline
receive_buf function. At that poing tty_buffer_flush() kicks in and sets both
tty->buf.head and tty->buf.tail to NULL. When flush_to_ldisc() finishes, it
restores tty->buf.head but doesn't touch tty->buf.tail. This corrups the
buffer queue, and the next call to tty_buffer_request_room() will allocate a
new buffer and overwrite tty->buf.head. The previous buffer is then lost
forever without being released.
(Thanks to Laurent for the above text, for finding, disgnosing and reporting
the bug)
- Use tty->flags bits for the flush status.
- Wait for the flag to clear again before returning
- Fix the doc error noted
- Fix flush of empty queue leaving stale flushpending
[akpm@linux-foundation.org: cleanup]
Signed-off-by: Alan Cox <alan@redhat.com>
Acked-by: Paul Fulghum <paulkf@microgate.com>
Cc: Laurent Pinchart <laurentp@cse-semaphore.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
A warning note from Sam Ravnborg about kconfig's select evilness,
dependencies and the future (slightly corrected).
Signed-off-by: Jarek Poplawski <jarkao2@o2.pl>
Cc: Sam Ravnborg <sam@ravnborg.org>
Cc: Roman Zippel <zippel@linux-m68k.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
In Documentation/sysrq.txt, the description of 'h' says that any key not
listed *above* will generate help. That's obviously not true since all the
keys listed below 'h' will do what they are described to do, not display help.
So change the text so that it says that any key not listed in the table will
generate help, which is what really happens.
Signed-off-by: Jesper Juhl <jesper.juhl@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
This version brings a number of new checks, and a number of bug
fixes. Of note:
- checks for spacing on round and square bracket combinations
- loosening of the single statement brace checks, to allow
them when they contain comments or where other blocks in a
compound statement have them.
- parks the multple declaration support
- allows architecture defines in architecture specific headers
Andy Whitcroft (21):
Version: 0.09
loosen single statement brace checks
fix up multiple declaration to avoid function arguments
add some function space parenthesis check exceptions
handle EXPORT_'s with parentheses in their names
clean up some warnings in multi-line macro bracketing support
park the multiple declaration checks
make block brace checks count comments as a statement
__volatile__ and __extension__ are not functions
allow architecture specific defined within architecture includes
check spacing on square brackets
check spacing on parentheses
ensure we apply checks to the part before start comment
check #ifdef conditional spacing
handle __init_refok and __must_check
add noinline to inline checks
prevent email addresses from tripping spacing checks
handle typed initialiser spacing
handle line contination as end of line
add bool to the type matcher
refine EXPORT_SYMBOL checks to handle pointers
Signed-off-by: Andy Whitcroft <apw@shadowen.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Long ago I've noticed (but didn't pay much attention) that
spi_mpc83xx using PM calculations that differs from what
specs describe. I.e.
u8 pm = mpc83xx_spi->spibrg / (spi->max_speed_hz * 4);
While specs says: "The SPI baud rate generator clock source (either
system clock or system clock divided by 16, depending on DIV16 bit) is
divided by 4 * ([PM] + 1), a range from 4 to 64.".
Thus " - 1" is missing in the spi_mpc83xx's formula.
Why nobody noticed that bug? Probably because sysclk usually less then
user expects, e.g. you expect 200 MHz, but real clock is 198 MHz,
and integer rounding helps when this formula is used.
Suppose it's SPI in QE, SYSCLK at 198 MHz, thus SPIBRG at 99MHz, 25 MHz
requested.
PM = (99MHz / ( 25 MHz * 4 )), PM == 0, output SPICLK will be 24.75 MHz
At lower frequencies this bug is more noticeable, though.
And this bug shows itself in all its beauty if SYSCLK is equal or a bit
more than you expect (200 MHz SYSCLK, 100 MHz SPIBRG):
PM = (100MHz / ( 25 MHz * 4 )), PM == 1, output SPICLK will be 12.625 MHz!
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
For MPC8349E input to the SPI Baud Rate Generator is SYSCLK, but it's
SYSCLK/2 for MPC8323E (SPI in QE). Fix this, and remove confusion by
renaming the mpc83xx_spi->sysclk member as mpc83xx_spi->spibrg.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Documentation/watchdog/watchdog.txt does not exist, it is Documentation/watchdog/wdt.txt
Signed-off-by: Gabriel Craciunescu <nix.or.die@googlemail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
This is add a document for memory hotplug to describe "How to use" and
"Current status".
Signed-off-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Signed-off-by: Yasunori Goto <y-goto@jp.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
cm4000_cs.c and cm4040_cs.c call the internal release function with
an argument of wrong type. this fixes bug #8485
Signed-off-by: Daniel Ritz <daniel.ritz@gmx.ch>
Cc: Bill McConnaughey <mcconnau@biochem.wustl.edu>
Cc: Natalie Protasevich <protasnb@gmail.com>
Cc: Harald Welte <laforge@gnumonks.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
On some systems some PFNs reported by the early initialization code as
'nosave' may be invalid. If we try to set the corresponding bits in the
hibernation bitmap, BUG_ON() in memory_bm_find_bit() will be triggered and
the system won't be able to boot (cf.
https://bugzilla.novell.com/show_bug.cgi?id=296242).
Prevent this from happening by verifying if the 'nosave' PFNs are valid in
mark_nosave_pages().
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
ecryptfs_init() exits without doing any cleanup jobs if
ecryptfs_init_messaging() fails. In that case, eCryptfs leaves
sysfs entries, leaks memory, and causes an invalid page fault.
This patch fixes the problem.
Signed-off-by: Ryusuke Konishi <konishi.ryusuke@lab.ntt.co.jp>
Acked-by: Michael Halcrow <mhalcrow@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Signed-off-by: Gabriel Craciunescu <nix.or.die@googlemail.com>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
After /proc/sys rewrite it was left unused.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Misplaced #endif is hiding the numa_zonelist_order sysctl when !SECURITY.
Signed-off-by: Lee Schermerhorn <lee.schermerhorn@hp.com>
Cc: Mel Gorman <mel@csn.ul.ie>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
When ecryptfs_lookup() is called against special files, eCryptfs generates
the following errors because it tries to treat them like regular eCryptfs
files.
Error opening lower file for lower_dentry [0xffff810233a6f150], lower_mnt [0xffff810235bb4c80], and flags
[0x8000]
Error opening lower_file to read header region
Error attempting to read the [user.ecryptfs] xattr from the lower file; return value = [-95]
Valid metadata not found in header region or xattr region; treating file as unencrypted
For instance, the problem can be reproduced by the steps below.
# mkdir /root/crypt /mnt/crypt
# mount -t ecryptfs /root/crypt /mnt/crypt
# mknod /mnt/crypt/c0 c 0 0
# umount /mnt/crypt
# mount -t ecryptfs /root/crypt /mnt/crypt
# ls -l /mnt/crypt
This patch fixes it by adding a check similar to directories and
symlinks.
Signed-off-by: Ryusuke Konishi <konishi.ryusuke@lab.ntt.co.jp>
Acked-by: Michael Halcrow <mhalcrow@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Connect up the fallocate() system call.
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
This builds upon my previous attempts to resolve some jitter problems seen
with the Matrox G450 and G550 -based cards, including odd disparities observed
between x86 and Power -based machines in a somewhat less hackish way (removing
the hacked ifdefs).
Apparently, preference should be given to use the DVI PLL when frequencies
permit, the Standard PLL otherwise. The max pixel clock for the panellink
interface is extracted from the PInS information on the card and used as a
limit to determine which PLL to use.
Signed-off-by: Paul A. Clarke <pc@us.ibm.com>
Acked-by: Petr Vandrovec <petr@vandrovec.name>
Signed-off-by: Antonino Daplas <adaplas@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
The current version is very old and does not correctly specify how to
set the video mode.
Signed-off by: Adrian McMenamin <adrian@mcmen.demon.co.uk>
Signed-off-by: Antonino Daplas <adaplas@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
- better handling of the pvr2 registers based on more up to date information.
Testing shows that it seems to work pretty well at 16bpp, 24bpp and 32bpp -
including proper rendering of the boot logo at all levels (previously this was
a bit broken even at 16bpp) and giving white against black text. Really
detailed testing (eg with X11) requires support for the maple bus - which
isn't (currently - next project assuming this is okay) available, but I have
no reason to think this is broken.
Signed-off by: Adrian McMenamin <adrian@mcmen.demon.co.uk>
Acked-by: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Antonino Daplas <adaplas@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Reported by: Adrian McMenamin <adrianmcmenamin@gmail.com>
This driver will oops when the pseudo_palette[] is written as u32 but not when
written as u16. When written as u32, it corrupts the adjacent 'mmio_base'
field of struct pvr2fb_par. Fix by using framebuffer_alloc()/release() to
allocate struct fb_info and struct pvr2fb_par, and create the pseudo_palette[]
as part of struct pvr2fb_par.
Signed-off-by: Antonino Daplas <adaplas@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Fix compile warning ('map_override unused') if fbcon is compiled as a module
and CONFIG_FRAMEBUFFER_CONSOLE_DETECT_PRIMARY=n.
[akpm@linux-foundation.org: cleanup]
Signed-off-by: Antonino Daplas <adaplas@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Visualize-EG, Graffiti and A4450A graphics cards on PARISC can
be configured in double-buffer and standard mode, but the stifb
driver supports standard mode only.
This patch detects double-buffered cards more reliable.
It is a real bugfix for a very nasty problem for all parisc users which have
wrongly configured their graphic card. The problem: The stifb graphics driver
will not detect that the card is wrongly configured and then nevertheless just
enables the graphics mode, which it shouldn't. In the end, the user will see
no further updates / boot messages on the screen.
We had documented this problem already on our FAQ
(http://parisc-linux.org/faq/index.html#viseg "Why do I get corrupted graphics
with my Vis-EG/Graffiti/A4450A card?") but people still run into this problem.
So having this fix in as early as possible can help us.
Signed-off-by: Helge Deller <deller@gmx.de>
Signed-off-by: Antonino Daplas <adaplas@gmail.com>
Cc: <stable@kernel.org>
Cc: Kyle McMartin <kyle@mcmartin.ca>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Need to initialize map_bh.b_state to zero. Otherwise, in case of a faulty
user-buffer its possible to go into dio_zero_block() and submit a page by
mistake - since it checks for buffer_new().
http://marc.info/?l=linux-kernel&m=118551339032528&w=2
akpm: Linus had a (better) patch to just do a kzalloc() in there, but it got
lost. Probably this version is better for -stable anwyay.
Signed-off-by: Badari Pulavarty <pbadari@us.ibm.com>
Acked-by: Joe Jin <joe.jin@oracle.com>
Acked-by: Zach Brown <zach.brown@oracle.com>
Cc: gurudas pai <gurudas.pai@oracle.com>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
I have had four seperate system lockups attributable to this exact problem
in two days of testing. Instead of trying to handle all the weird end
cases and wrap, how about changing it to look for exactly what we appear
to want.
The following patch removes a couple races in setup_APIC_timer. One occurs
when the HPET advances the COUNTER past the T0_CMP value between the time
the T0_CMP was originally read and when COUNTER is read. This results in
a delay waiting for the counter to wrap. The other results from the counter
wrapping.
This change takes a snapshot of T0_CMP at the beginning of the loop and
simply loops until T0_CMP has changed (a tick has happened).
<later>
I have one small concern about the patch. I am not sure it meets the intent
as well as it should. I think we are trying to match APIC timer interrupts up
with the hpet counter increment. The event which appears to be disturbing
this loop in our test environment is the NMI watchdog. What we believe has
been happening with the existing code is the setup_APIC_timer loop has read
the CMP value, and the NMI watchdog code fires for the first time. This
results in a series of icache miss slowdowns and by the time we get back to
things it has wrapped.
I think this code is trying to get the CMP as close to the counter value as
possible. If that is the intent, maybe we should really be testing against a
"window" around the CMP. Something like COUNTER = CMP+/2. It appears COUNTER
should get advanced every 89nSec (IIRC). The above seems like an unreasonably
small window, but may be necessary. Without documentation, I am not sure of
the original intent with this code.
In summary, this code fixes my boot hangs, but since I am not certain of the
intent of the existing code, I am not certain this has not introduced new bugs
or unexpected behaviors.
Signed-off-by: Robin Holt <holt@sgi.com>
Acked-by: Andi Kleen <ak@suse.de>
Cc: Vojtech Pavlik <vojtech@suse.cz>
Cc: "Aaron Durbin" <adurbin@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Cc: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Bryan Wu <bryan.wu@analog.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
There's a little problem in Documentation/vm/slabinfo.c
The code is using "%d" in a printf() call to print an 'unsigned long'.
This patch corrects it to use "%lu" instead.
Signed-off-by: Jesper Juhl <jesper.juhl@gmail.com>
Signed-off-by: Christoph Lameter <clameter@sgi.com>
|
|
The dynamic dma kmalloc creation can run into trouble if a
GFP_ATOMIC allocation is the first one performed for a certain size
of dma kmalloc slab.
- Move the adding of the slab to sysfs into a workqueue
(sysfs does GFP_KERNEL allocations)
- Do not call kmem_cache_destroy() (uses slub_lock)
- Only acquire the slub_lock once and--if we cannot wait--do a trylock.
This introduces a slight risk of the first kmalloc(x, GFP_DMA|GFP_ATOMIC)
for a range of sizes failing due to another process holding the slub_lock.
However, we only need to acquire the spinlock once in order to establish
each power of two DMA kmalloc cache. The possible conflict is with the
slub_lock taken during slab management actions (create / remove slab cache).
It is rather typical that a driver will first fill its buffers using
GFP_KERNEL allocations which will wait until the slub_lock can be acquired.
Drivers will also create its slab caches first outside of an atomic
context before starting to use atomic kmalloc from an interrupt context.
If there are any failures then they will occur early after boot or when
loading of multiple drivers concurrently. Drivers can already accomodate
failures of GFP_ATOMIC for other reasons. Retries will then create the slab.
Signed-off-by: Christoph Lameter <clameter@sgi.com>
|
|
The MAX_PARTIAL checks were supposed to be an optimization. However, slab
shrinking is a manually triggered process either through running slabinfo
or by the kernel calling kmem_cache_shrink.
If one really wants to shrink a slab then all operations should be done
regardless of the size of the partial list. This also fixes an issue that
could surface if the number of partial slabs was initially above MAX_PARTIAL
in kmem_cache_shrink and later drops below MAX_PARTIAL through the
elimination of empty slabs on the partial list (rare). In that case a few
slabs may be left off the partial list (and only be put back when they
are empty).
Signed-off-by: Christoph Lameter <clameter@sgi.com>
|
