aboutsummaryrefslogtreecommitdiff
AgeCommit message (Collapse)Author
2008-02-28[BNX2X]: fix slowpath races and lockingEliezer Tamir
Fixed locking between fastpath and slowpath operations. Corrected order of traffic disabling to prevent race when going down under traffic. - first have the microcode drop all incoming packets - then do the slowpath stuff - only then reset the MAC Got rid of in_reset_task. Remove_one() and friends would deference a null pointer if init_one failed. Signed-off-by: Eliezer Tamir <eliezert@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-02-28[BNX2X]: fix HW attentions and error handlingEliezer Tamir
Some of the HW attentions, used to indicate an error were not properly acked. This will cause the driver to endlessly receive interrupts when such an error happens. Had to break the code into smaller chunks because it got too nested. Signed-off-by: Eliezer Tamir <eliezert@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-02-28[BNX2X]: fix MSI-X/INT#A errataEliezer Tamir
Errata A0.158 workaround. Running in INT#A mode after running with MSI-X fails due to a PCI core bug. Signed-off-by: Eliezer Tamir <eliezert@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-02-28[BNX2X]: correct statisticsEliezer Tamir
Errors were summed improperly, some stats were missing. Signed-off-by: Eliezer Tamir <eliezert@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-02-28[BNX2X]: Correct RX filtering and MC configurationEliezer Tamir
The configuration of RX filtering needed the following corrections: Drop flags need to be set per Rx queue. Have to tell the microcode to collect drop stats, and properly wait for them to complete when going down. Sometimes we failed to detect proper completion due to a logical error in the wait loop. Signed-off-by: Eliezer Tamir <eliezert@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-02-28[BNX2X]: Correct Link managementEliezer Tamir
Properly protect PHY access between two devices on the same board with a HW lock. Use GPIO to clear all previous configurations before changing link parameters. Shut down the external PHY in case of fan failure. Reducing the MDC/MDIO clock to 2.5MHz due to problems with some devices. Resolve the flow control response according to autoneg with external PHY. Unmasking all PHY interrupts in single write to prevent a race in the interrupts order. LASI indication fixes to work with peculiarities of PHYs. Disable MAC RX to avoid a HW bug when closing the MAC under traffic. Disable parallel detection on HiGig due to HW limitation. Updating the shared memory structure to work with the current bootcode. Signed-off-by: Eliezer Tamir <eliezert@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-02-28[BNX2X]: Correct init_one()Eliezer Tamir
Correct PCI-E info printed by init_one() In one case it failed to free the netdev. Signed-off-by: Eliezer Tamir <eliezert@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-02-28[BNX2X]: Spelling fixesEliezer Tamir
Signed-off-by: Eliezer Tamir <eliezert@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-02-28[IPCOMP]: Disable BH on output when using shared tfmHerbert Xu
Because we use shared tfm objects in order to conserve memory, (each tfm requires 128K of vmalloc memory), BH needs to be turned off on output as that can occur in process context. Previously this was done implicitly by the xfrm output code. That was lost when it became lockless. So we need to add the BH disabling to IPComp directly. Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-02-28Merge branch 'master' of ↵David S. Miller
master.kernel.org:/pub/scm/linux/kernel/git/linville/wireless-2.6
2008-02-28SSB PCI core driver: use new SPROM data structureAurelien Jarno
Switch the SSB PCI core driver to the new SPROM data structure now that the old one has been removed. Signed-off-by: Aurelien Jarno <aurelien@aurel32.net> Acked-by: Michael Buesch <mb@bu3sch.de> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2008-02-28Don't build bcm43xx if SSB is static and b43 PCI-SSB bridge is enabled.Alexey Zaytsev
This may happen e.g. when the ssb is statically enables by the b44 driver, and the b43 pci-ssb bridge is enbled by the b43/b43legacy drivers, or the b43/b43legacy drivers are built statically. Signed-off-by: Alexey Zaytsev <alexey.zaytsev@gmail.com> Acked-by: Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2008-02-28Use a separate config option for the b43 pci to ssb bridge.Alexey Zaytsev
The bridge code was unnecessary enabled by the b44 driver, but it prevents the bcm43xx driver from being loaded, as the bridge claims the same pci ids. Now we enable the birdge only if the b43{legacy} drivers are selected. Signed-off-by: Alexey Zaytsev <alexey.zaytsev@gmail.com> Acked-by: Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2008-02-28libertas: Remove unused exportsRoland Dreier
The libertas driver exports a number of symbols with no in-tree users; remove these unused exports. lbs_reset_device() is completely unused, with no callers at all, so remove the function completely. A couple of these unused exported symbols are static, which causes the following build error on ia64 with gcc 4.2.3: drivers/net/wireless/libertas/main.c:1375: error: __ksymtab_lbs_remove_mesh causes a section type conflict drivers/net/wireless/libertas/main.c:1354: error: __ksymtab_lbs_add_mesh causes a section type conflict Signed-off-by: Roland Dreier <rolandd@cisco.com> Acked-by: Holger Schurig <hs4233@mail.mn-solutions.de> Acked-by: Dan Williams <dcbw@redhat.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2008-02-28mac80211: fix kmalloc vs. net_ratelimitJohannes Berg
The "goto end;" part definitely must not be rate limited. Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2008-02-28rt2x00: Fix rt2x00lib_reset_link_tuner()Ivo van Doorn
rt2x00lib_reset_link_tuner() can be called from within the link tuner itself. This means that it should _not_ call rt2x00lib_stop_link_tuner() since that will cause the thread to hang. Reorder the things that should be done during a link tuner reset and during a link tuner start. Also make antenna tuning the last step of the link tuner since it could possibly reset some statistical information which we need for average calculation. Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2008-02-28rt2x00: Don't switch to antenna with low rssiIvo van Doorn
When rssi_a > rssi_b is true and the current antenna was already antenna A, then rt2x00 incorrectly jumped to antenna B. Also don't configure the antenna when there has been no change in the antenna setup. Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2008-02-28rt2x00: Add link tuner safe RX toggle statesIvo van Doorn
This adds 2 new states which both are used to toggle the RX. These new states are required for usage inside the link tuner thread, because the normal RX toggling will stop the link tuner thread. While it is possible that the link tuner thread itself is the caller of the RX toggle (when using software antenna diversity). Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2008-02-28rt2x00: Fix antenna diversityIvo van Doorn
Fix 2 issues in antenna diversity selection. 1) the following statement will always return true. if ((rssi_curr - rssi_old) > -5 || (rssi_curr - rssi_old) < 5) It is cleaner to check if the absolute value is smaller then 5. 2) Only enable software diversity when default antenna setup indicates support for it. Don't select it when the hardware does not indicate support for it... Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2008-02-28gelic wireless driver needs WIRELESS_EXT supportSebastian Siewior
| CC drivers/net/ps3_gelic_wireless.o | /home/bigeasy/git/linux-2.6/drivers/net/ps3_gelic_wireless.c: In function 'gelic_wl_setup_netdev_ops': | /home/bigeasy/git/linux-2.6/drivers/net/ps3_gelic_wireless.c:2660: error: 'struct net_device' has no member named 'wireless_data' | /home/bigeasy/git/linux-2.6/drivers/net/ps3_gelic_wireless.c:2661: error: 'struct net_device' has no member named 'wireless_handlers' | make[3]: *** [drivers/net/ps3_gelic_wireless.o] Error 1 | make[2]: *** [drivers/net] Error 2 | make[1]: *** [drivers] Error 2 | make[1]: *** Waiting for unfinished jobs.... | make: *** [sub-make] Error 2 Signed-off-by: Sebastian Siewior <sebastian@breakpoint.cc> Acked-by: Masakazu Mokuno <mokuno@sm.sony.co.jp> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2008-02-28PS3: gelic: Link the wireless net_device structure to the corresponding ↵Masakazu Mokuno
device structure Link the net_device structure of the wireless part to the corresponding device structure. Without this, the sysfs node for this net_device would not have 'device' link. Signed-off-by: Masakazu Mokuno <mokuno@sm.sony.co.jp> Acked-by: Dan Williams <dcbw@redhat.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2008-02-28rndis_wlan: fix sparse warningsJohannes Berg
It is obviously wrong to use an enum in a little endian struct, and those other enums should be declared differently. Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Acked-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2008-02-27[NETFILTER]: Fix NF_QUEUE_NR() parenthesisPatrick McHardy
Properly add parens around the macro argument. This is not needed by the kernel but the macro is exported to userspace, so it shouldn't make any assumptions. Also use NF_VERDICT_BITS instead of NF_VERDICT_QBTIS for the left-shift since thats whats logically correct. Signed-off-by: Patrick McHardy <kaber@trash.net> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-02-27[NETFILTER]: xt_conntrack: fix IPv4 address comparisonJan Engelhardt
Signed-off-by: Jan Engelhardt <jengelh@computergmbh.de> Signed-off-by: Patrick McHardy <kaber@trash.net> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-02-27[NETFILTER]: xt_conntrack: fix missing boolean clampingJan Engelhardt
Signed-off-by: Jan Engelhardt <jengelh@computergmbh.de> Signed-off-by: Patrick McHardy <kaber@trash.net> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-02-27[NETFILTER]: nf_conntrack: fix smp_processor_id() in preemptible code warningPatrick McHardy
Since we're using RCU for the conntrack hash now, we need to avoid getting preempted or interrupted by BHs while changing the stats. Fixes warning reported by Tilman Schmidt <tilman@imap.cc> when using preemptible RCU: [ 48.180297] BUG: using smp_processor_id() in preemptible [00000000] code: ntpdate/3562 [ 48.180297] caller is __nf_conntrack_find+0x9b/0xeb [nf_conntrack] [ 48.180297] Pid: 3562, comm: ntpdate Not tainted 2.6.25-rc2-mm1-testing #1 [ 48.180297] [<c02015b9>] debug_smp_processor_id+0x99/0xb0 [ 48.180297] [<fac643a7>] __nf_conntrack_find+0x9b/0xeb [nf_conntrack] Tested-by: Tilman Schmidt <tilman@imap.cc> Tested-by: Christian Casteyde <casteyde.christian@free.fr> [Bugzilla #10097] Signed-off-by: Patrick McHardy <kaber@trash.net> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-02-27[IPV6] SYSCTL: Fix possible memory leakage in error path.YOSHIFUJI Hideaki
In error path, we do need to free memory just allocated. Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-02-26[INET]: Don't create tunnels with '%' in name.Pavel Emelyanov
Four tunnel drivers (ip_gre, ipip, ip6_tunnel and sit) can receive a pre-defined name for a device from the userspace. Since these drivers call the register_netdevice() (rtnl_lock, is held), which does _not_ generate the device's name, this name may contain a '%' character. Not sure how bad is this to have a device with a '%' in its name, but all the other places either use the register_netdev(), which call the dev_alloc_name(), or explicitly call the dev_alloc_name() before registering, i.e. do not allow for such names. This had to be prior to the commit 34cc7b, but I forgot to number the patches and this one got lost, sorry. Signed-off-by: Pavel Emelyanov <xemul@openvz.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-02-26[AF_KEY]: Fix oops by converting to proc_net_*().David S. Miller
To make sure the procfs visibility occurs after the ->proc_fs ops are setup, use proc_net_fops_create() and proc_net_remove(). This also fixes an OOPS after module unload in that the name string for remove was wrong, so it wouldn't actually be removed. That bug was introduced by commit 61145aa1a12401ac71bcc450a58c773dd6e2bfb9 ("[KEY]: Clean up proc files creation a bit.") Signed-off-by: David S. Miller <davem@davemloft.net>
2008-02-26CONNECTOR: make cn_already_initialized staticLi Zefan
It is used in connector.c only, so make it static. Signed-off-by: Li Zefan <lizf@cn.fujitsu.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-02-26[IPV4]: Reset scope when changing addressBjorn Mork
This bug did bite at least one user, who did have to resort to rebooting the system after an "ifconfig eth0 127.0.0.1" typo. Deleting the address and adding a new is a less intrusive workaround. But I still beleive this is a bug that should be fixed. Some way or another. Another possibility would be to remove the scope mangling based on address. This will always be incomplete (are 127/8 the only address space with host scope requirements?) We set the scope to RT_SCOPE_HOST if an IPv4 interface is configured with a loopback address (127/8). The scope is never reset, and will remain set to RT_SCOPE_HOST after changing the address. This patch resets the scope if the address is changed again, to restore normal functionality. Signed-off-by: Bjorn Mork <bjorn@mork.no> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-02-26[IPV6]: Add missing initializations of the new nl_info.nl_net fieldBenjamin Thery
Add some more missing initializations of the new nl_info.nl_net field in IPv6 stack. This field will be used when network namespaces are fully supported. Signed-off-by: Benjamin Thery <benjamin.thery@bull.net> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-02-26[MACVLAN]: Update Kconfig to refer to iproutePatrick McHardy
Since the macvlan release I had at least 5 users asking how to configure it since the old userspace tool doesn't work with the version in the kernel. Add a pointer to the Kconfig help. Signed-off-by: Patrick McHardy <kaber@trash.net> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-02-26bluetooth: delete timer in l2cap_conn_del()Thomas Gleixner
Delete a possibly armed timer before kfree'ing the connection object. Solves: http://lkml.org/lkml/2008/2/15/514 Reported-by:Quel Qun <kelk1@comcast.net> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-02-24tipc: fix integer as NULL pointer sparse warnings in tipcHarvey Harrison
net/tipc/cluster.c:145:2: warning: Using plain integer as NULL pointer net/tipc/link.c:3254:36: warning: Using plain integer as NULL pointer net/tipc/ref.c:151:15: warning: Using plain integer as NULL pointer net/tipc/zone.c:85:2: warning: Using plain integer as NULL pointer Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-02-24Merge branch 'upstream-davem' of ↵David S. Miller
master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/netdev-2.6
2008-02-24Linux 2.6.25-rc3Linus Torvalds
2008-02-24i2c-i801: Add support for the ICH10Gaston, Jason D
Add the Intel ICH10 SMBus Controller DeviceID's and updates Tolapai support. Signed-off-by: Jason Gaston <jason.d.gaston@intel.com> Signed-off-by: Jean Delvare <khali@linux-fr.org>
2008-02-24i2c: Make i2c_register_board_info() a NOP when CONFIG_I2C_BOARDINFO=nDavid Brownell
Don't require platform code to be #ifdeffed according to whether I2C is enabled or not ... if it's not enabled, let GCC compile out all I2C device declarations. (Issue noted on an NSLU2 build that didn't configure I2C.) Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Jean Delvare <khali@linux-fr.org>
2008-02-24i2c-pca-isa: Add access check to legacy ioportsChristian Krafft
When probing i2c-pca-isa writes to legacy ioports, which crashes the kernel if there is no device at that port. This patch adds a check_legacy_ioport call, so probe fails gracefully and thus prevents the oops. Signed-off-by: Christian Krafft <krafft@de.ibm.com> Signed-off-by: Jean Delvare <khali@linux-fr.org>
2008-02-24Alchemy: compile fixManuel Lauss
Commit 8b798c4d16b762d15f4055597ff8d87f73b35552 broke alchemy build, fix it. Pointed out by Adrian Bunk. Signed-off-by: Manuel Lauss <mano@roarinelk.homelinux.net> Signed-off-by: Jean Delvare <khali@linux-fr.org>
2008-02-24i2c: Storage class should be before const qualifierTobias Klauser
The C99 specification states in section 6.11.5: The placement of a storage-class specifier other than at the beginning of the declaration specifiers in a declaration is an obsolescent feature. Signed-off-by: Tobias Klauser <tklauser@distanz.ch> Signed-off-by: Jean Delvare <khali@linux-fr.org>
2008-02-24i2c-pxa: Misc fixesWolfram Sang
While working on the PCA9564-platform driver, I sometimes had a glimpse at the pxa-driver. I found some suspicious places, and this patch contains my suggestions. Note: They are not tested, due to no hardware. [JD: Some more fixes.] Signed-off-by: Wolfram Sang <w.sang@pengutronix.de> Signed-off-by: Jean Delvare <khali@linux-fr.org> Tested-by: Mike Rapoport <mike@compulab.co.il> Tested-by: Eric Miao <ymiao3@marvell.com>
2008-02-24ARM: OMAP: Release i2c_adapter after use (Siemens SX1)Jean Delvare
Each call to i2c_get_adapter() must be followed by a call to i2c_put_adapter() to release the grabbed reference. Otherwise the reference count grows forever and the adapter can never be unregistered. Signed-off-by: Jean Delvare <khali@linux-fr.org> Acked-by: Vladimir Ananiev <vovan888@gmail.com> Acked-by: Tony Lindgren <tony@atomide.com>
2008-02-23Merge branch 'upstream-linus' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev * 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev: libata-core: fix kernel-doc warning sata_fsl: fix build with ATA_VERBOSE_DEBUG [libata] ahci: AMD SB700/SB800 SATA support 64bit DMA libata-pmp: clear hob for pmp register accesses libata: automatically use DMADIR if drive/bridge requires it power_state: get rid of write-only variable in SATA pata_atiixp: Use 255 sector limit
2008-02-24libata-core: fix kernel-doc warningRandy Dunlap
Fix libata-core kernel-doc warning: Warning(linux-2.6.25-rc2-git6//drivers/ata/libata-core.c:168): No description found for parameter 'ap' Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
2008-02-24sata_fsl: fix build with ATA_VERBOSE_DEBUGAnton Vorontsov
This patch fixes build and few warnings when ATA_VERBOSE_DEBUG is defined: CC drivers/ata/sata_fsl.o drivers/ata/sata_fsl.c: In function ‘sata_fsl_fill_sg’: drivers/ata/sata_fsl.c:338: warning: format ‘%x’ expects type ‘unsigned int’, but argument 3 has type ‘void *’ drivers/ata/sata_fsl.c:338: warning: format ‘%x’ expects type ‘unsigned int’, but argument 4 has type ‘struct prde *’ drivers/ata/sata_fsl.c: In function ‘sata_fsl_qc_issue’: drivers/ata/sata_fsl.c:459: error: ‘csr_base’ undeclared (first use in this function) drivers/ata/sata_fsl.c:459: error: (Each undeclared identifier is reported only once drivers/ata/sata_fsl.c:459: error: for each function it appears in.) drivers/ata/sata_fsl.c: In function ‘sata_fsl_freeze’: drivers/ata/sata_fsl.c:525: error: ‘csr_base’ undeclared (first use in this function) make[2]: *** [drivers/ata/sata_fsl.o] Error 1 Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
2008-02-24[libata] ahci: AMD SB700/SB800 SATA support 64bit DMAShane Huang
SB700 SATA controller can support 64 bit DMA, the previous commit badc2341579511a247f5993865aa68379e283c5c was added with careless reference to SB600, which should be modified by this patch. Signed-off-by: Shane Huang <shane.huang@amd.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
2008-02-24libata-pmp: clear hob for pmp register accessesMark Lord
>> Mark Lord wrote: >>> Tejun, I've added PMP to sata_mv, and am now trying to get it >>> to work with a Marvell PM attached. >>> >>> And the behaviour I see is very bizarre. >>> >>> After hard+soft resets, the PM signature is found, >>> and libata interrogates the PM registers. >>> >>> It successfully reads register 0, and then register 1. >>> But all subsequent registers read out (incorrectly) as zeros. ... This behavior has been confirmed by Marvell with a SATA analyzer. The Marvell port-multiplier apparently likes to see clean HOB information when accessing PMP registers. Since sata_mv uses PIO shadow register access, this doesn't happen automatically, as it might in a more purely FIS-based driver (eg. ahci). One way to fix this is to flag these commands with ATA_TFLAG_LBA48, forcing libata to write out the HOB fields with known (zero) values. Signed-off-by: Saeed Bishara <saeed@marvell.com> Acked-by: Mark Lord <mlord@pobox.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
2008-02-24libata: automatically use DMADIR if drive/bridge requires itTejun Heo
Back in 2.6.17-rc2, a libata module parameter was added for atapi_dmadir. That's nice, but most SATA devices which need it will tell us about it in their IDENTIFY PACKET response, as bit-15 of word-62 of the returned data (as per ATA7, ATA8 specifications). So for those which specify it, we should automatically use the DMADIR bit. Otherwise, disc writing will fail by default on many SATA-ATAPI drives. This patch adds ATA_DFLAG_DMADIR and make ata_dev_configure() set it if atapi_dmadir is set or identify data indicates DMADIR is necessary. atapi_xlat() is converted to check ATA_DFLAG_DMADIR before setting DMADIR. Original patch is from Mark Lord. Signed-off-by: Tejun Heo <htejun@gmail.com> Cc: Mark Lord <mlord@pobox.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
generated by cgit v1.2.3 (git 2.25.1) at 2024-11-27 16:55:29 +0000