aboutsummaryrefslogtreecommitdiff
AgeCommit message (Collapse)Author
2008-09-09MXC: add RTCK alternate function definitionsLuotao Fu
This one adds definitions to configure RTCK pad (PE16) in primary and alternate function. The RTCK Pin is used by one wire master controller and as JTAG Clock return. Signed-off-by: Luotao Fu <l.fu@pengutronix.de> Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
2008-09-09mxc: add cscr register defintionsLuotao Fu
This adds macros to get CSCR upper, lower and additional registers. These registers are needed to configure a chip select line. The offset layouts of these Registers are identical on mx27 and mx31, hence we can use the macros in generic way Signed-off-by: Luotao Fu <l.fu@pengutronix.de> Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
2008-09-09MX31: add macros to configure spi pinsLuotao Fu
this adds convenience values usable by mxc_iomux_mode() to configure Pins of the spi interfaces on mx31. Signed-off-by: Luotao Fu <l.fu@pengutronix.de> Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
2008-09-09MXC: Lets handle IRQ by priority, defined with exported API functionDarius Augulis
Signed-off-by: Darius Augulis <augulis.darius@gmail.com> Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
2008-09-09i.MX31ADS: Add CPLD interrupts demultiplexing (take 3).Gilles Chanteperdrix
Needed for 8250 serial port and CS89x0 ethernet interface. Signed-off-by: Gilles Chanteperdrix <gilles.chanteperdrix@xenomai.org> Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
2008-09-09i.MX31ADS: Enable the first IMX serial port. (take 3)Gilles Chanteperdrix
Signed-off-by: Gilles Chanteperdrix <gilles.chanteperdrix@xenomai.org> Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
2008-09-09i.MX27: add definitions for USB pinsSascha Hauer
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
2008-09-09i.MX2: make SoC devices globally availableSascha Hauer
Make SoC devices globally available to boards rather than using a device specific init function. Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
2008-09-09i.MX3: make SoC devices globally availableSascha Hauer
Make SoC devices globally available to boards rather than using a device specific init function. Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
2008-09-09MXC: add convenience function to register platform devicesSascha Hauer
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
2008-09-08Merge branch 'master' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/hskinnemoen/avr32-2.6 * 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/hskinnemoen/avr32-2.6: avr32: pm_standby low-power ram bug fix avr32: Fix lockup after Java stack underflow in user mode
2008-09-08Merge branch 'merge' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc * 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc: powerpc: Fix rare boot build breakage powerpc/spufs: Fix possible scheduling of a context to multiple SPEs powerpc/spufs: Fix race for a free SPU powerpc/spufs: Fix multiple get_spu_context()
2008-09-08Merge git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6Linus Torvalds
* git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6: Revert "crypto: camellia - Use kernel-provided bitops, unaligned access helpers"
2008-09-08Merge master.kernel.org:/home/rmk/linux-2.6-armLinus Torvalds
* master.kernel.org:/home/rmk/linux-2.6-arm: [ARM] 5241/1: provide ioremap_wc() [ARM] omap: fix virtual vs physical address space confusions [ARM] remove unused #include <version.h> [ARM] omap: fix build error in ohci-omap.c [ARM] omap: fix gpio.c build error
2008-09-08Merge branch 'sched-fixes-for-linus' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip * 'sched-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: sched: arch_reinit_sched_domains() must destroy domains to force rebuild sched, cpuset: rework sched domains and CPU hotplug handling (v4)
2008-09-08Merge branch 'upstream-linus' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev * 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev: ahci: RAID mode SATA patch for Intel Ibex Peak DeviceIDs pata_sil680: remove duplicate pcim_enable_device libata-sff: kill spurious WARN_ON() in ata_hsm_move() sata_nv: disable hardreset for generic ahci: disable PMP for marvell ahcis sata_mv: add RocketRaid 1720 PCI ID to driver ahci, pata_marvell: play nicely together
2008-09-08Fix format of MAINTAINERSUwe Kleine-König
... one entry lacked a colon which broke one of my scripts. Signed-off-by: Uwe Kleine-König <ukleinek@informatik.uni-freiburg.de> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-09-08Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6Linus Torvalds
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: bridge: don't allow setting hello time to zero netns : fix kernel panic in timewait socket destruction pkt_sched: Fix qdisc state in net_tx_action() netfilter: nf_conntrack_irc: make sure string is terminated before calling simple_strtoul netfilter: nf_conntrack_gre: nf_ct_gre_keymap_flush() fixlet netfilter: nf_conntrack_gre: more locking around keymap list netfilter: nf_conntrack_sip: de-static helper pointers
2008-09-08Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc-2.6Linus Torvalds
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc-2.6: sparc64: Prevent sparc64 from invoking irq handlers on offline CPUs sparc64: Fix IPI call locking.
2008-09-08usb: fix null deferences in low level usb serialJason Wessel
The hw interface drivers for the usb serial devices deference the tty structure to set up the parameters for the initial console. The tty structure should be passed as a parameter to the set_termios() call. Signed-off-by: Jason Wessel <jason.wessel@windriver.com> Signed-off-by: Alan Cox <alan@redhat.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-09-08NFS: Restore missing hunk in NFS mount option parserChuck Lever
Automounter maps can contain mount options valid for other NFS implementations but not for Linux. The Linux automounter uses the mount command's "-s" command line option ("s" for "sloppy") so that mount requests containing such options are not rejected. Commit f45663ce5fb30f76a3414ab3ac69f4dd320e760a attempted to address a known regression with text-based NFS mount option parsing. Unrecognized mount options would cause mount requests to fail, even if the "-s" option was used on the mount command line. Unfortunately, this commit was not complete as submitted. It adds a new mount option, "sloppy". But it is missing a hunk, so it now allows NFS mounts with unrecognized mount options, even if the "sloppy" option is not present. This could be a problem if a required critical mount option such as "sync" is misspelled, for example, and is considered a regression from 2.6.26. This patch restores the missing hunk. Now, the default behavior of text-based NFS mount options is as before: any unrecognized mount option will cause the mount to fail. Please include this in 2.6.27-rc. Thanks to Neil Brown for reporting this. Signed-off-by: Chuck Lever <chuck.lever@oracle.com> Acked-by: J. Bruce Fields <bfields@citi.umich.edu> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-09-08bridge: don't allow setting hello time to zeroStephen Hemminger
Dushan Tcholich reports that on his system ksoftirqd can consume between %6 to %10 of cpu time, and cause ~200 context switches per second. He then correlated this with a report by bdupree@techfinesse.com: http://marc.info/?l=linux-kernel&m=119613299024398&w=2 and the culprit cause seems to be starting the bridge interface. In particular, when starting the bridge interface, his scripts are specifying a hello timer interval of "0". The bridge hello time can't be safely set to values less than 1 second, otherwise it is possible to end up with a runaway timer. Signed-off-by: Stephen Hemminger <shemminger@vyatta.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-09-08netns : fix kernel panic in timewait socket destructionDaniel Lezcano
How to reproduce ? - create a network namespace - use tcp protocol and get timewait socket - exit the network namespace - after a moment (when the timewait socket is destroyed), the kernel panics. # BUG: unable to handle kernel NULL pointer dereference at 0000000000000007 IP: [<ffffffff821e394d>] inet_twdr_do_twkill_work+0x6e/0xb8 PGD 119985067 PUD 11c5c0067 PMD 0 Oops: 0000 [1] SMP CPU 1 Modules linked in: ipv6 button battery ac loop dm_mod tg3 libphy ext3 jbd edd fan thermal processor thermal_sys sg sata_svw libata dock serverworks sd_mod scsi_mod ide_disk ide_core [last unloaded: freq_table] Pid: 0, comm: swapper Not tainted 2.6.27-rc2 #3 RIP: 0010:[<ffffffff821e394d>] [<ffffffff821e394d>] inet_twdr_do_twkill_work+0x6e/0xb8 RSP: 0018:ffff88011ff7fed0 EFLAGS: 00010246 RAX: ffffffffffffffff RBX: ffffffff82339420 RCX: ffff88011ff7ff30 RDX: 0000000000000001 RSI: ffff88011a4d03c0 RDI: ffff88011ac2fc00 RBP: ffffffff823392e0 R08: 0000000000000000 R09: ffff88002802a200 R10: ffff8800a5c4b000 R11: ffffffff823e4080 R12: ffff88011ac2fc00 R13: 0000000000000001 R14: 0000000000000001 R15: 0000000000000000 FS: 0000000041cbd940(0000) GS:ffff8800bff839c0(0000) knlGS:0000000000000000 CS: 0010 DS: 0018 ES: 0018 CR0: 000000008005003b CR2: 0000000000000007 CR3: 00000000bd87c000 CR4: 00000000000006e0 DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 DR3: 0000000000000000 DR6: 00000000ffff0ff0 DR7: 0000000000000400 Process swapper (pid: 0, threadinfo ffff8800bff9e000, task ffff88011ff76690) Stack: ffffffff823392e0 0000000000000100 ffffffff821e3a3a 0000000000000008 0000000000000000 ffffffff821e3a61 ffff8800bff7c000 ffffffff8203c7e7 ffff88011ff7ff10 ffff88011ff7ff10 0000000000000021 ffffffff82351108 Call Trace: <IRQ> [<ffffffff821e3a3a>] ? inet_twdr_hangman+0x0/0x9e [<ffffffff821e3a61>] ? inet_twdr_hangman+0x27/0x9e [<ffffffff8203c7e7>] ? run_timer_softirq+0x12c/0x193 [<ffffffff820390d1>] ? __do_softirq+0x5e/0xcd [<ffffffff8200d08c>] ? call_softirq+0x1c/0x28 [<ffffffff8200e611>] ? do_softirq+0x2c/0x68 [<ffffffff8201a055>] ? smp_apic_timer_interrupt+0x8e/0xa9 [<ffffffff8200cad6>] ? apic_timer_interrupt+0x66/0x70 <EOI> [<ffffffff82011f4c>] ? default_idle+0x27/0x3b [<ffffffff8200abbd>] ? cpu_idle+0x5f/0x7d Code: e8 01 00 00 4c 89 e7 41 ff c5 e8 8d fd ff ff 49 8b 44 24 38 4c 89 e7 65 8b 14 25 24 00 00 00 89 d2 48 8b 80 e8 00 00 00 48 f7 d0 <48> 8b 04 d0 48 ff 40 58 e8 fc fc ff ff 48 89 df e8 c0 5f 04 00 RIP [<ffffffff821e394d>] inet_twdr_do_twkill_work+0x6e/0xb8 RSP <ffff88011ff7fed0> CR2: 0000000000000007 This patch provides a function to purge all timewait sockets related to a network namespace. The timewait sockets life cycle is not tied with the network namespace, that means the timewait sockets stay alive while the network namespace dies. The timewait sockets are for avoiding to receive a duplicate packet from the network, if the network namespace is freed, the network stack is removed, so no chance to receive any packets from the outside world. Furthermore, having a pending destruction timer on these sockets with a network namespace freed is not safe and will lead to an oops if the timer callback which try to access data belonging to the namespace like for example in: inet_twdr_do_twkill_work -> NET_INC_STATS_BH(twsk_net(tw), LINUX_MIB_TIMEWAITED); Purging the timewait sockets at the network namespace destruction will: 1) speed up memory freeing for the namespace 2) fix kernel panic on asynchronous timewait destruction Signed-off-by: Daniel Lezcano <dlezcano@fr.ibm.com> Acked-by: Denis V. Lunev <den@openvz.org> Acked-by: Eric W. Biederman <ebiederm@xmission.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-09-08ahci: RAID mode SATA patch for Intel Ibex Peak DeviceIDsSeth Heasley
Add the Intel Ibex Peak (PCH) SATA RAID Controller DeviceIDs. Signed-off-by: Seth Heasley <seth.heasley@intel.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-09-08pata_sil680: remove duplicate pcim_enable_deviceDavid Milburn
Remove duplicate call to pcim_enable_device in sil680_init_one. Signed-off-by: David Milburn <dmilburn@redhat.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-09-08libata-sff: kill spurious WARN_ON() in ata_hsm_move()Tejun Heo
On HSM_ST_ERR, ata_hsm_move() triggers WARN_ON() if AC_ERR_DEV or AC_ERR_HSM is not set. PHY events may trigger HSM_ST_ERR with other error codes and, with or without it, there just isn't much reason to do WARN_ON() on it. Even if error code is not set there, core EH logic won't have any problem dealing with the error condition. OSDL bz#11065 reports this problem. Signed-off-by: Tejun Heo <tj@kernel.org> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-09-08sata_nv: disable hardreset for genericTejun Heo
of them being unifying probing, hotplug and EH reset paths uniform. Previously, broken hardreset could go unnoticed as it wasn't used during probing but when something goes wrong or after hotplug the problem will surface and bite hard. OSDL bug 11195 reports that sata_nv generic flavor falls into this category. Hardreset itself succeeds but PHY stays offline after hardreset. I tried longer debounce timing but the result was the same. http://bugzilla.kernel.org/show_bug.cgi?id=11195 So, it seems we'll have to drop hardreset from the generic flavor. Signed-off-by: Tejun Heo <tj@kernel.org> Cc: Peer Chen <pchen@nvidia.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-09-08ahci: disable PMP for marvell ahcisTejun Heo
Marvell ahcis don't play nicely with PMPs. Disable it. Reported by KueiHuan Chen in the following thread. http://thread.gmane.org/gmane.linux.ide/33296 Signed-off-by: Tejun Heo <tj@kernel.org> Cc: KueiHuan Chen <kueihuan.chen@gmail.com> Cc: Mark Lord <mlord@pobox.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-09-08sata_mv: add RocketRaid 1720 PCI ID to driverMark Lord
Signed-off-by: Petr Jelen <petr.jelen@gmail.com> Signed-off-by: Mark Lord <mlord@pobox.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-09-08ahci, pata_marvell: play nicely togetherAlan Cox
I've been chasing Jeff about this for months. Jeff added the Marvell device identifiers to the ahci driver without making the AHCI driver handle the PATA port. This means a lot of users can't use current kernels and in most distro cases can't even install. This has been going on since March 2008 for the 6121 Marvell, and late 2007 for the 6145!!! This was all pointed out at the time and repeatedly ignored. Bugs assigned to Jeff about this are ignored also. To quote Jeff in email > "Just switch the order of 'ahci' and 'pata_marvell' in > /etc/modprobe.conf, then use Fedora's tools regenerate the initrd. > See? It's not rocket science, and the current configuration can be > easily made to work for Fedora users." (Which isn't trivial, isn't end user, shouldn't be needed, and as it usually breaks at install time is in fact impossible) To quote Jeff in August 2007 > " mv-ahci-pata > Marvell 6121/6141 PATA support. Needs fixing in the 'PATA controller > command' area before it is usable, and can go upstream." Only he add the ids anyway later and caused regressions, adding a further id in March causing more regresions. The actual fix for the moment is very simple. If the user has included the pata_marvell driver let it drive the ports. If they've only selected for SATA support give them the AHCI driver which will run the port a fraction faster. Allow the user to control this decision via ahci.marvell_enable as a module parameter so that distributions can ship 'it works' defaults and smarter users (or config tools) can then flip it over it desired. Signed-off-by: Alan Cox <alan@redhat.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-09-08powerpc: Fix rare boot build breakageHugh Dickins
A make -j20 powerpc kernel build broke a couple of months ago saying: In file included from arch/powerpc/boot/gunzip_util.h:13, from arch/powerpc/boot/prpmc2800.c:21: arch/powerpc/boot/zlib.h:85: error: expected ‘:’, ‘,’, ‘;’, ‘}’ or ‘__attribute__’ before ‘*’ token arch/powerpc/boot/zlib.h:630: warning: type defaults to ‘int’ in declaration of ‘Byte’ arch/powerpc/boot/zlib.h:630: error: expected ‘;’, ‘,’ or ‘)’ before ‘*’ token It happened again yesterday: too rare for me to confirm the fix, but it looks like the list of dependants on gunzip_util.h was incomplete. Signed-off-by: Hugh Dickins <hugh@veritas.com> Signed-off-by: Paul Mackerras <paulus@samba.org>
2008-09-08Revert "crypto: camellia - Use kernel-provided bitops, unaligned access helpers"Herbert Xu
This reverts commit bd699f2df6dbc2f4cba528fe598bd63a4d3702c5, which causes camellia to fail the included self-test vectors. It has also been confirmed that it breaks existing encrypted disks using camellia. Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
2008-09-07pkt_sched: Fix qdisc state in net_tx_action()Jarek Poplawski
net_tx_action() can skip __QDISC_STATE_SCHED bit clearing while qdisc is neither ran nor rescheduled, which may cause endless loop in dev_deactivate(). Reported-by: Denys Fedoryshchenko <denys@visp.net.lb> Tested-by: Denys Fedoryshchenko <denys@visp.net.lb> Signed-off-by: Jarek Poplawski <jarkao2@gmail.com> Acked-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-09-07netfilter: nf_conntrack_irc: make sure string is terminated before calling ↵Patrick McHardy
simple_strtoul Alexey Dobriyan points out: 1. simple_strtoul() silently accepts all characters for given base even if result won't fit into unsigned long. This is amazing stupidity in itself, but 2. nf_conntrack_irc helper use simple_strtoul() for DCC request parsing. Data first copied into 64KB buffer, so theoretically nothing prevents reading past the end of it, since data comes from network given 1). This is not actually a problem currently since we're guaranteed to have a 0 byte in skb_shared_info or in the buffer the data is copied to, but to make this more robust, make sure the string is actually terminated. Signed-off-by: Patrick McHardy <kaber@trash.net> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-09-07netfilter: nf_conntrack_gre: nf_ct_gre_keymap_flush() fixletAlexey Dobriyan
It does "kfree(list_head)" which looks wrong because entity that was allocated is definitely not list_head. However, this all works because list_head is first item in struct nf_ct_gre_keymap. Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com> Signed-off-by: Patrick McHardy <kaber@trash.net> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-09-07netfilter: nf_conntrack_gre: more locking around keymap listAlexey Dobriyan
gre_keymap_list should be protected in all places. (unless I'm misreading something) Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com> Signed-off-by: Patrick McHardy <kaber@trash.net> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-09-07netfilter: nf_conntrack_sip: de-static helper pointersAlexey Dobriyan
Helper's ->help hook can run concurrently with itself, so iterating over SIP helpers with static pointer won't work reliably. Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com> Signed-off-by: Patrick McHardy <kaber@trash.net> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-09-08powerpc/spufs: Fix possible scheduling of a context to multiple SPEsAndre Detsch
We currently have a race when scheduling a context to a SPE - after we have found a runnable context in spusched_tick, the same context may have been scheduled by spu_activate(). This may result in a panic if we try to unschedule a context that has been freed in the meantime. This change exits spu_schedule() if the context has already been scheduled, so we don't end up scheduling it twice. Signed-off-by: Andre Detsch <adetsch@br.ibm.com> Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
2008-09-06Merge branch 'for-linus' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input * 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input: Input: i8042 - make Lenovo 3000 N100 blacklist entry more specific Input: bcm5974 - add BTN_TOUCH event for mousedev benefit Input: bcm5974 - improve finger tracking and counting Input: bcm5974 - small formatting cleanup Input: bcm5974 - add maintainer entry
2008-09-06Merge branch 'x86-fixes-for-linus' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip * 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: x86: cpu_init(): fix memory leak when using CPU hotplug x86: pda_init(): fix memory leak when using CPU hotplug x86, xen: Use native_pte_flags instead of native_pte_val for .pte_flags x86: move mtrr cpu cap setting early in early_init_xxxx x86: delay early cpu initialization until cpuid is done x86: use X86_FEATURE_NOPL in alternatives x86: add NOPL as a synthetic CPU feature bit x86: boot: stub out unimplemented CPU feature words
2008-09-06Merge branch 'timers-fixes-for-linus' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip * 'timers-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: clocksource, acpi_pm.c: check for monotonicity clocksource, acpi_pm.c: use proper read function also in errata mode ntp: fix calculation of the next jiffie to trigger RTC sync x86: HPET: read back compare register before reading counter x86: HPET fix moronic 32/64bit thinko clockevents: broadcast fixup possible waiters HPET: make minimum reprogramming delta useful clockevents: prevent endless loop lockup clockevents: prevent multiple init/shutdown clockevents: enforce reprogram in oneshot setup clockevents: prevent endless loop in periodic broadcast handler clockevents: prevent clockevent event_handler ending up handler_noop
2008-09-06Merge branch 'for-linus' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6 * 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6: Fix CONFIG_AC97_BUS dependency
2008-09-06Merge branch 'upstream' of git://ftp.linux-mips.org/pub/scm/upstream-linusLinus Torvalds
* 'upstream' of git://ftp.linux-mips.org/pub/scm/upstream-linus: [MIPS] Probe initrd header only if explicitly specified [MIPS] TX39xx: Add missing local_flush_icache_range initialization [MIPS] TXx9: Fix txx9_pcode initialization [MIPS] Fix WARNING: at kernel/smp.c:290 [MIPS] Fix data bus error recovery
2008-09-06Merge branch 'sched/cpuset' into sched/urgentIngo Molnar
2008-09-06x86: cpu_init(): fix memory leak when using CPU hotplugAndreas Herrmann
Exception stacks are allocated each time a CPU is set online. But the allocated space is never freed. Thus with one CPU hotplug offline/online cycle there is a memory leak of 24K (6 pages) for a CPU. Fix is to allocate exception stacks only once -- when the CPU is set online for the first time. Signed-off-by: Andreas Herrmann <andreas.herrmann3@amd.com> Cc: akpm@linux-foundation.org Signed-off-by: Ingo Molnar <mingo@elte.hu>
2008-09-06x86: pda_init(): fix memory leak when using CPU hotplugAndreas Herrmann
pda->irqstackptr is allocated whenever a CPU is set online. But it is never freed. This results in a memory leak of 16K for each CPU offline/online cycle. Fix is to allocate pda->irqstackptr only once. Signed-off-by: Andreas Herrmann <andreas.herrmann3@amd.com> Cc: akpm@linux-foundation.org Signed-off-by: Ingo Molnar <mingo@elte.hu>
2008-09-06x86, xen: Use native_pte_flags instead of native_pte_val for .pte_flagsEduardo Habkost
Using native_pte_val triggers the BUG_ON() in the paravirt_ops version of pte_flags(). Signed-off-by: Eduardo Habkost <ehabkost@redhat.com> Acked-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com> Signed-off-by: Ingo Molnar <mingo@elte.hu>
2008-09-06sched: arch_reinit_sched_domains() must destroy domains to force rebuildMax Krasnyansky
What I realized recently is that calling rebuild_sched_domains() in arch_reinit_sched_domains() by itself is not enough when cpusets are enabled. partition_sched_domains() code is trying to avoid unnecessary domain rebuilds and will not actually rebuild anything if new domain masks match the old ones. What this means is that doing echo 1 > /sys/devices/system/cpu/sched_mc_power_savings on a system with cpusets enabled will not take affect untill something changes in the cpuset setup (ie new sets created or deleted). This patch fixes restore correct behaviour where domains must be rebuilt in order to enable MC powersaving flags. Test on quad-core Core2 box with both CONFIG_CPUSETS and !CONFIG_CPUSETS. Also tested on dual-core Core2 laptop. Lockdep is happy and things are working as expected. Signed-off-by: Max Krasnyansky <maxk@qualcomm.com> Tested-by: Vaidyanathan Srinivasan <svaidy@linux.vnet.ibm.com> Signed-off-by: Ingo Molnar <mingo@elte.hu>
2008-09-06x86: move mtrr cpu cap setting early in early_init_xxxxYinghai Lu
Krzysztof Helt found MTRR is not detected on k6-2 root cause: we moved mtrr_bp_init() early for mtrr trimming, and in early_detect we only read the CPU capability from cpuid, so some cpu doesn't have that bit in cpuid. So we need to add early_init_xxxx to preset those bit before mtrr_bp_init for those earlier cpus. this patch is for v2.6.27 Reported-by: Krzysztof Helt <krzysztof.h1@wp.pl> Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com> Signed-off-by: Ingo Molnar <mingo@elte.hu>
2008-09-06x86: delay early cpu initialization until cpuid is doneKrzysztof Helt
Move early cpu initialization after cpu early get cap so the early cpu initialization can fix up cpu caps. Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl> Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com> Signed-off-by: Ingo Molnar <mingo@elte.hu>
generated by cgit v1.2.3 (git 2.25.1) at 2024-11-06 13:42:05 +0000