aboutsummaryrefslogtreecommitdiff
AgeCommit message (Collapse)Author
2007-10-10[PATCH] libertas: monitor mode support for OLPC firmwareLuis Carlos Cobo
Driver support for the monitor mode support that will be available in the next OLPC 'bleeding edge' Marvell firmware release (most likely, 5.110.16.p2). To activate monitor mode, echo mode > /sys/class/net/{ethX,mshX}/device/libertas_rtap where mode is the hex mask that specifies which frames to sniff (in short, 0x1 for data, 0x2 for all management but beacons, 0x4 for beacons). Any non zero mode will activate the monitor mode, inhibiting transmission in ethX and mshX interfaces and routing all the incoming traffic to a new rtapX interface that will output the packets in 802.11+radiotap headers format. Signed-off-by: Luis Carlos Cobo <luisca@cozybit.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2007-10-10[PATCH] libertas: fix a few wext abuses...Jean Tourrilhes
o SIOCGIWNAME is not designed to return the version number of the driver. On the other hand, you are free to abuse SIOCGIWNICKN for that purpose. o Don't attempt to fix the WE19/WE20 transition in the driver, because your fixes are bogus, and redundant with the code in the kernel (you may endup with +2, you can't read 32 char ESSID...). o In SIOCSIWTXPOW, if you specified in iwrange that you want dBm, you should only get dBm, which allow to reduce code bloat. Signed-off-by: Jean Tourrilhes <jt@hpl.hp.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2007-10-10[PATCH] libertas: keep mesh autostart enabled while asleepLuis Carlos Cobo
After loading the firmware, mesh autostart will be disabled. After that, the user will still be able to enable or disable it at will. On suspend, it will be always activated and later on resume it will go back to the state it had before going to sleep. Signed-off-by: Luis Carlos Cobo <luisca@cozybit.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2007-10-10[PATCH] libertas: revert CAPINFO_MASK to its original valueLuis Carlos Cobo
CAPINFO_MASK changed on commits 981f187b and a091095b. Reverting to the original value. Also move CAPINFO_MASK into the sole user, join.c. CAPINFO_MASK should be in host CPU byte order; capability is converted to device byte order elsewhere. This fixes OLPC ticket #2161 Signed-off-by: Luis Carlos Cobo <luisca@cozybit.com> Acked-by: Dan Williams <dcbw@redhat.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2007-10-10[PATCH] libertas: push mesh beacon bit to userspace in scan resultsDan Williams
Signed-off-by: Dan Williams <dcbw@redhat.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2007-10-10[PATCH] libertas: send association events on adhoc reassociationDan Williams
Send association event to userspace when reassociating to the same ad-hoc network, because it's still an association. Signed-off-by: Dan Williams <dcbw@redhat.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2007-10-10[PATCH] libertas: fix two debug statements in cmdresp.cHolger Schurig
Purely cosmetic: this moves an lbs_deb_enter() to the proper place and changes an erraneous lbs_deb_enter_args() into lbs_deb_leave_args() Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2007-10-10[PATCH] libertas: remove bss_descriptor->timestampHolger Schurig
Noone used this variable. Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2007-10-10[PATCH] libertas: remove bss_descriptior->networktsfHolger Schurig
This value was parsed out, but then nowhere used ... except in some debugfs output. I can't imagine anyone wanting to use this value for anything real (as no other driver exports it), so bye-bye. Along this, made the columns of /sys/kernel/debug/libertas_wireless/*/getscantable align again. Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2007-10-10[PATCH] libertas: remove adapter->scantypeHolger Schurig
scantype was initialized with CMD_SCAN_TYPE_ACTIVE, but there is no code that would ever change it, so we can use that variable directly. Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2007-10-10[PATCH] libertas: remove adapter->scanmodeHolger Schurig
scanmode was initialized with CMD_BSS_TYPE_ANY, but there is no code that ever can store another value there, so it can go away. Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2007-10-10[PATCH] libertas: remove adapter->beaconperiodHolger Schurig
beaconperiod was initialized with MRVDRV_BEACON_INTERVAL, but there is no code that would ever change it's value. We can use the define directly. Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2007-10-10[PATCH] libertas: remove adapter->adhoc_grate_enabledHolger Schurig
The variable was initialized with 0 (false). There is no code that would ever change it, so we can use the false-patch directly. Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2007-10-10[PATCH] libertas: remove adapter->listenintervalHolger Schurig
listeninterval was initialized with MRVDRV_DEFAULT_LISTEN_INTERVAL, but there exists that would ever change it. So we can use this define directly. Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2007-10-10[PATCH] libertas: remove adapter->regiontableindexHolger Schurig
The value was computed, but then never used. Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2007-10-10[PATCH] libertas: remove adapter->atimwindowHolger Schurig
This varaible was initialized with 0 but there is no code that would ever change it's value. So it can go away. Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2007-10-10[PATCH] libertas: remove adapter->multipledtimHolger Schurig
multipledtim was initialized with MRVDRV_DEFAULT_MULTIPLE_DTIM and then kept at that value, so we could use that define directly. Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2007-10-10[PATCH] libertas: remove adapter->locallistenintervalHolger Schurig
locallisteninterval was initialized with 0, but there is no code that changes it, rendering it rather useless. Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2007-10-10[PATCH] libertas: remove adapter->nullpktintervalHolger Schurig
No code ever initialized this variable, so it was 0 because of kzalloc(). But no other code changes it, making it rather useless. Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2007-10-10[PATCH] libertas: remove adapter->{data,bcn}_avg_factorHolger Schurig
Those two variables were initialized with some default values, but there is no code that would ever change them. So we could use as well the defaults directly. Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2007-10-10[PATCH] libertas: remove adapter->rxpd_rateHolger Schurig
No code uses the contents of this variable, so it can go. Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2007-10-10[PATCH] libertas: remove adapter->txrateHolger Schurig
The value of txrate was only set by a CMD_802_11_TX_RATE_QUERY command, but there was no code in the driver that ever issued this command. Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2007-10-10[PATCH] libertas: fix WEXT quality reportingDan Williams
Found by Ronak and others at Marvell. Signed-off-by: Dan Williams <dcbw@redhat.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2007-10-10[PATCH] libertas: remove adapter->pkttxctrlHolger Schurig
The variable was initialized to 0 and nowhere else changed, so basically the per-packet TX control wasn't used. Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2007-10-10[PATCH] libertas: remove adapter->scanprobesHolger Schurig
The variable was initialized to 0 and nowhere else to anything different. Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2007-10-10[PATCH] libertas: remove adapter->prescanHolger Schurig
The value 1 was assigned to it and there was nowhere any code that would have changed that to 0. Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2007-10-10[PATCH] libertas: remove adapter->{rx,tx}antennaHolger Schurig
There was nowhere any code that used the values of those variables. This patch also removes two static functions that are now unused. Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2007-10-10[PATCH] libertas: remove unused adapter->prev_XXXX variablesHolger Schurig
There were just used in some debug output, but nowhere else. Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2007-10-10[PATCH] add support for Marvell 8385 CF cardsHolger Schurig
This patch adds support for Marvell based 8385 compact flash cards. Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2007-10-10[PATCH] libertas: Avoid MESH_AUTOSTARTED spam on consoleLuis Carlos Cobo
Signed-off-by: Luis Carlos Cobo <luisca@cozybit.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2007-10-10[PATCH] libertas: use LBS_DEB_HOST for host-to-card communicationsHolger Schurig
... and LBS_DEB_CMD for command execution. Also tidies misc comments to give a consistent output. Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2007-10-10[PATCH] libertas: use LBS_DEB_HOST for host-to-card communicationsHolger Schurig
... and LBS_DEB_CMD for command execution. Also tidies misc comments to give a consistent output. Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2007-10-10[PATCH] libertas: remove a hundred CMD_RET_xxx definitionsHolger Schurig
types.h contains the same amount of CMD_RET_xxx and CMD_xxx definitions. They contains the same info: the firmware command opcode and, when the firmware sends back a result, the command opcode ORed with 0x8000. Having the same data twice in the source code is redundant and can lead to errors (e.g. if you update or delete only one instance). This patch removed all CMD_RET_xxx definitions and introduces a simple CMD_RET() macro. Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2007-10-10[PATCH] libertas: make the hex dumper nicerHolger Schurig
Currently, when you define LBS_DEB_HEX, you get every hex dump in the whole driver, e.g. for LBS_DEB_CMD, LBS_DEB_RX, LBS_DEB_TX etc. This patch makes sure that you only get the hexdump that you're interested in. Renamed lbs_dbg_hex() into lbs_deb_hex(), like the other lbs_deb_XXX() macros. Made lbs_deb_hex() issue a line feed (and a new prompt) after 16 bytes. As lbs_deb_hex() now prints the ":" after the prompt by itself, removed the misc colons in the various *.c files. lbs_deb_XXX() now print the debug category as well. As lbs_deb_XXX() --- and especially lbs_deb_11d() --- now print the category, I removed various "11D:" prefixes in 11d.c as well. Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2007-10-10[PATCH] Support for mesh autostart deactivation through sysfsLuis Carlos Cobo
echo 0 > /sys/class/net/mshX/autostart_enabled This is supported from Marvell firmware version 5.110.16.p0 (to be released). Signed-off-by: Luis Carlos Cobo <luisca@cozybit.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2007-10-10[PATCH] libertas: remove debugmodeHolger Schurig
There is nowhere any place that set's this variable. Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2007-10-10[PATCH] libertas: tune hardware info outputHolger Schurig
This changes the output of hardware related info from: libertas: GET_HW_SPEC: FWReleaseVersion- 5.0.11.p0 libertas: GET_HW_SPEC: Permanent addr- 0:16:41:72:f6:a8 libertas: GET_HW_SPEC: hwifversion=0x2 version=0x213 to: libertas: GET_HW_SPEC: FWReleaseVersion: 5.0.11.p0 libertas: GET_HW_SPEC: Permanent addr: 00:16:41:72:f6:a8 libertas: GET_HW_SPEC: hwifversion: 0x2, version: 0x213 Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2007-10-10[PATCH] libertas: access mesh_dev more carefullyHolger Schurig
The CF/SDIO firmware doesn't support Mesh, so priv->mesh_dev is NULL there. Protect all accesses. Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2007-10-10[PATCH] libertas: uppercase some #definesHolger Schurig
Usually constants defined by #define are in ALL_UPPERCASE. This patch fixes this. I also shuffled the bits around so that they match the bit positions in the host-interrupt-state register of the CF/SDIO card :-) Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2007-10-10[PATCH] libertas: make more functions static & remove unused functionsHolger Schurig
Some functions where declared in header files, but used only once. They are now static functions. After doing this, I found out that some functions weren't used at all. I removed this dead code. Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2007-10-10[PATCH] libertas: fix one more sparse warningHolger Schurig
adhoc_rates_b is only used locally, so make it static Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2007-10-10[PATCH] libertas: remove fw.cHolger Schurig
Firmware download is quite different for different hardware. The SDIO and CF cards have two flat files that need to be downloaded, whereas the USB driver needs only one file, but with an internal structure. The code that handles this (USB only) structured file is currently in fw.c. This patch moves this code into if_usb.c. The remaining functions in fw.c have not much to do with firmware, they are various card- and network-stack initialisation functions. I've moved them into main.c. Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2007-10-10[PATCH] libertas: simplify and clean up data rate handlingDan Williams
Remove unused/duplicated fields and consolidate static data rate arrays, for example the libertas_supported_rates[] and datarates[] arrays in the bss_descriptor structure, and the libertas_supported_rates field in the wlan_adapter structure. Introduce libertas_fw_index_to_data_rate and libertas_data_rate_to_fw_index functions and use them everywhere firmware requires a rate index rather than a rate array. The firmware requires the 4 basic rates to have the MSB set, but most other stuff doesn't, like WEXT and mesh ioctls. Therefore, only set the MSB on basic rates when pushing rate arrays to firmware instead of doing a ton of (rate & 0x7f) everywhere. Signed-off-by: Dan Williams <dcbw@redhat.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2007-10-10[PATCH] libertas: wlan_ -> libertas_ function prefix renames for main.cDan Williams
Signed-off-by: Dan Williams <dcbw@redhat.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2007-10-10[PATCH] libertas: move generic firmware reset command to common codeDan Williams
It's not USB specific, so move it out of the USB interface code. Signed-off-by: Dan Williams <dcbw@redhat.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2007-10-10[PATCH] libertas: fix more mixed-case abuseDan Williams
Mistakently introduced by a previous patch to upper-case all command constants. Signed-off-by: Dan Williams <dcbw@redhat.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2007-10-10[PATCH] libertas: bump version to 322.p1Dan Williams
Signed-off-by: Dan Williams <dcbw@redhat.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2007-10-10[PATCH] libertas: new mesh control knobsDan Williams
Support for new mesh control knobs on firmware 5.220.11.p4: Signed-off-by: Luis Carlos Cobo <luisca@cozybit.com> Signed-off-by: Dan Williams <dcbw@redhat.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2007-10-10[PATCH] libertas: remove thread.h and make kthread usage clearerDan Williams
Remove the thread.h abstractions and opencode kthread stuff to make it clearer. Signed-off-by: Dan Williams <dcbw@redhat.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2007-10-10[PATCH] libertas: fix debug build breakage due to field renameDan Williams
Missed when fixing mixed-case structure field names. Signed-off-by: Dan Williams <dcbw@redhat.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
generated by cgit v1.2.3 (git 2.25.1) at 2024-12-02 06:09:40 +0000