aboutsummaryrefslogtreecommitdiff
AgeCommit message (Collapse)Author
2008-06-26V4L/DVB (8069): cx18: Fix S-Video and Compsite inputs for the Yuan MPC718 ↵Andy Walls
and enable card entry cx18: Fix S-Video and Compsite input settings for the Yuan MPC718 per user reports from Yuri Warczynski <Yuri.Warczynski@gmail.com> and Brian Hope <brian@hopefamily.info> and enable the card entry. The tuner reset GPIO pin is likely incorrect as the tuner firmware cannot be reloaded without a reboot. It is likely the audio routing is done via GPIO which is not implemented yet, as users report audio doesn't work for some inputs. Signed-off-by: Andy Walls <awalls@radix.net> Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
2008-06-26V4L/DVB (8068): cx18: Add I2C slave reset via GPIO upon initializationAndy Walls
cx18: Add I2C slave reset via GPIO upon initialization. One user, Michael <msd4824@yahoo.com>, has reported this allows his HVR-1600 EEPROM to be consistently recognized when using (long,) 100 msec delays. The delays in this commit are nominal (10 & 40 msec) and need testing/tuning on boards with I2C problems to find the right values. Signed-off-by: Andy Walls <awalls@radix.net> Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
2008-06-26V4L/DVB (8067): cx18: Fix firmware load for case when digital capture ↵Andy Walls
happens first This is a fix for the case when a digital capture from dvr0 happens first after modprobe, before access to any cx18 v4l2 device nodes. The initial dvb feed start has been changed to load the firmware if not already loaded. Also fixed a use counter to correct dvb feed accounting if starting the transport DMA fails. Signed-off-by: Andy Walls <awalls@radix.net> Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
2008-06-26V4L/DVB (8066): cx18: Fix audio mux input definitions for HVR-1600 Line In 2 ↵Andy Walls
and FM radio Fix the cx18-cards.c structures for the HVR-1600 to reflect that audio Line In 2 and FM radio audio go to AIN3 and AIN4 of the CS5345 mux respectively. Verified by physical inspection of an HVR-1600MCE, by listening to FM broadcasts with the HVR-1600MCE, and by comparing with the card definition for a PVR-150 in ivtv. Signed-off-by: Andy Walls <awalls@radix.net> Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
2008-06-26V4L/DVB (8063): cx18: Fix unintended auto configurations in cx18-av-coreAndy Walls
Change the cx18-av-core code so that accesses to cx23418 av core that cause auto-configuration will be adjusted to emulate the auto-configuration behavior of the cx25843. This fixes the VBI displayed as video at the top of the frame for NTSC and probably other things. Signed-off-by: Andy Walls <awalls@radix.net> Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
2008-06-26V4L/DVB (8061): cx18: only select tuner / frontend modules if !DVB_FE_CUSTOMISEMichael Krufky
The automatic Kconfig selection for tuners and frontends should be conditional, based on !DVB_FE_CUSTOMISE. This patch corrects the selection for VIDEO_CX18 on MEDIA_TUNER_MXL5005S and DVB_S5H1409 Signed-off-by: Michael Krufky <mkrufky@linuxtv.org> Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
2008-06-26V4L/DVB (8048): saa7134: Fix entries for Avermedia A16d and Avermedia E506Tim Farrington
Also, adds IR table for Avermedia A16d Signed-off-by: Tim Farrington <timf@iinet.net.au> Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
2008-06-26V4L/DVB (8044): au8522: tuning optimizationsMichael Krufky
If the current modulation and frequency is already set to the desired parameters, then don't re-tune. Don't store current frequency until after we've tuned successfully. Force a re-tune after resume from standby. Signed-off-by: Michael Krufky <mkrufky@linuxtv.org> Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
2008-06-26V4L/DVB (8043): au0828: add support for additional USB device id'sMichael Krufky
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org> Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
2008-06-26V4L/DVB (8042): DVB-USB UMT-010 channel scan oopsAustin Lund
In the umt-010 driver the struct umt_properties sets the number of URBs for transfer to 20. But in dvb-usb.h MAX_NO_URBS_FOR_DATA_STREAM is set to 10. Not surprisingly this causes an oops for all devices which use the umt-010 chipset when they are inserted. fix on Kaffeine channel scan for Initialize stream count using MAX_NO_URBS_FOR_DATA_STREAM. Signed-off-by: Tim Gardner <tim.gardner@canonical.com> Signed-off-by: maximilian attems <max@stro.at> Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
2008-06-26V4L/DVB (8040): soc-camera: remove soc_camera_host_class classGuennadi Liakhovetski
Devices can either be class devices or bus devices, not both at the same time. Soc-camera host devices usually have a platform device as their parent. Trying to also register them with a class crashes the kernel, when linked statically. Interestingly, it works when built as a module. Thanks to Paulius Zaleckas for reporting. Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@pengutronix.de> Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
2008-06-26V4L/DVB (8039): pxa-camera: fix platform_get_irq() error handling.Guennadi Liakhovetski
platform_get_irq() returns a negative value on error, not 0. Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@pengutronix.de> Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
2008-06-26V4L/DVB (8037): tda18271: ensure that the thermometer is off during channel ↵Michael Krufky
configuration Having the thermometer on during channel configuration could cause tuning instability. Signed-off-by: Michael Krufky <mkrufky@linuxtv.org> Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
2008-06-26V4L/DVB (8036): tda18271: toggle rf agc speed mode on TDA18271HD/C2 onlyMichael Krufky
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org> Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
2008-06-26V4L/DVB (8035): tda18271: dont touch EB14 if rf_cal lookup is out of rangeMichael Krufky
The TDA18271HD/C1 rf_cal map lookup is expected to go out of range outside of the frequency window 41 MHz - 61.1 MHz. In these cases, the internal RF tracking filters calibration mechanism is used. Signed-off-by: Michael Krufky <mkrufky@linuxtv.org> Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
2008-06-26V4L/DVB (8034): tda18271: fix IF notch frequency handlingMichael Krufky
The IF notch bit gets unset when we update the Main Post Div register value, before we have a chance to write the desired IF notch setting to the tuner. Move the IF notch configuration to after we update MPD. Signed-off-by: Michael Krufky <mkrufky@linuxtv.org> Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
2008-06-26V4L/DVB (8029): Improve error message at tda1004x_attachMauro Carvalho Chehab
When an error occurs at firmware loading, sometimes, tda1004x stops answering. Instead of reporting such error, attach code were assuming that the device were answering an invalid ID (0xff). This can be seen when enabling debug options: tda1004x: tda1004x_read_byte: reg=0x0 tda1004x: tda1004x_read_byte: error reg=0x0, ret=-5 Now, instead of reporting an invalid ID, it will report the correct error: tda10046: chip is not answering. Giving up. saa7133[0]/dvb: failed to attach tda10046 saa7133[0]/dvb: frontend initialization failed A possible improvement would be trying to reset the device. Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
2008-06-26V4L/DVB (8028): Improve error messages for tda1004x attachMauro Carvalho Chehab
A fresh copy of v.29 firmware, using get_firmware, is leading to an invalid firmware: DVB: registering new adapter (saa7133[0]) DVB: registering frontend 0 (Philips TDA10046H DVB-T)... tda1004x: setting up plls for 48MHz sampling clock tda1004x: found firmware revision ff -- invalid tda1004x: trying to boot from eeprom tda1004x: found firmware revision ff -- invalid tda1004x: waiting for firmware upload... tda1004x: Error during firmware upload tda1004x: found firmware revision ff -- invalid tda1004x: firmware upload failed Sometimes, loading/unloading this firmware makes tda1004x to return an invalid ID. However, there were no printk messages to help to identify what were the cause for the error. With this patch, it will now print: Invalid tda1004x ID = 0xff. Can't proceed saa7133[0]/dvb: failed to attach tda10046 saa7133[0]/dvb: frontend initialization failed Tested with LifeView FlyDVB-T Hybrid Cardbus/MSI TV @nywhere A/D NB Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
2008-06-26V4L/DVB (8027): saa7134: Avermedia A700: only s-video and composite input ↵Matthias Schwarzott
are working Describe exactly that only s-video and composite input are working on Avermedia A700 Signed-off-by: Matthias Schwarzott <zzam@gentoo.org> Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
2008-06-26V4L/DVB (8026): Avoids an OOPS if dev struct can't be successfully recoveredMauro Carvalho Chehab
On some alsa versions, it seems that snd_pcm_substream_chip(substream) is returning a NULL pointer. This causes an OOPS, as reported by: https://bugs.launchpad.net/ubuntu/+source/linux-ubuntu-modules-2.6.24/+bug/212271 https://bugs.launchpad.net/ubuntu/+source/alsa-driver/+bug/212960 This patch avoids the OOPS by not letting and open() succeed. Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
2008-06-26V4L/DVB (8022): saa7134: fix race between opening and closing the deviceMarcin Slusarz
decrementing dev->empress_users should be done as last action of ts_release, because it sleeps and write access to dev->empress_started is not protected in any way (additionally closing thread could mute audio after opening thread unmuted it) Signed-off-by: Marcin Slusarz <marcin.slusarz@gmail.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
2008-06-26V4L/DVB (8020): Fix callbacks functions of saa7134_empressDmitri Belimov
If I try v4l2-ctl --all -d /dev/video1 or v4l2-ctl --streamon -d /dev/video1 modules crashed: *pde = 00000000 Modules linked in: ac battery loop saa7134_empress(F) saa6752hs(F) tuner_simple(F) tuner_types(F) tea5767(F) tda9887(F) tda8290(F) tea5761(F) tuner(F) snd_cmipci snd_pcm snd_page_alloc snd_opl3_lib saa7134(F) snd_mpu401 parport_pc parport snd_timer snd_hwdep snd_mpu401_uart floppy rtc psmouse videodev(F) v4l1_compat(F) compat_ioctl32(F) v4l2_common(F) videobuf_dma_sg(F) videobuf_core(F) snd_rawmidi snd_seq_device via_ircc pcspkr snd ir_kbd_i2c(F) irda soundcore ir_common(F) crc_ccitt tveeprom(F) i2c_viapro i2c_core button via_agp agpgart evdev ext3 jbd mbcache ide_cd_mod cdrom ide_disk 8139cp via82cxxx ide_core 8139too mii ehci_hcd uhci_hcd usbcore thermal processor fan EIP is at __mutex_lock_slowpath+0x29/0x7b DS: 007b ES: 007b FS: 00d8 GS: 0033 SS: 0068 Process v4l2-ctl (pid: 2742, ti=ced7e000 task=cf325260 task.ti=ced7e000) d08e5411 00000000 ced7fed4 00000000 d0975acb 40045612 cfa86ee0 ffffffcd cf2b7000 ced7febc c03858d6 00000019 00000292 d089e4ec cf37b2a0 d089e4a0 Call Trace: [<c028b52b>] mutex_lock+0xa/0xb [<d08e5411>] videobuf_streamon+0xf/0x9a [videobuf_core] [<d0975acb>] __video_do_ioctl+0x136a/0x2d68 [videodev] [<d088f789>] task_end_request+0x40/0x51 [ide_core] [<d088c4aa>] ide_intr+0x187/0x192 [ide_core] [<c016a551>] mntput_no_expire+0x11/0x64 [<c0160b1c>] path_walk+0x90/0x98 [<d0977738>] video_ioctl2+0x173/0x239 [videodev] [<c0140936>] filemap_fault+0x202/0x370 [<c014930a>] __do_fault+0x2c3/0x2fe [<c014ab03>] handle_mm_fault+0x22a/0x49f [<c0162737>] vfs_ioctl+0x47/0x5d [<c0162992>] do_vfs_ioctl+0x245/0x258 [<c01629e6>] sys_ioctl+0x41/0x5b [<c01036a6>] sysenter_past_esp+0x5f/0x85 ======================= After this fix all of that commands works without problem: v4l2-ctl --all -d /dev/video1 Driver Info: Driver name : saa7134 Card type : Beholder BeholdTV M6 Extra Bus info : PCI:0000:00:0d.0 Driver version: 526 Capabilities : 0x05000001 Video Capture Read/Write Streaming Format Video Capture: Width/Height : 720/576 Pixel Format : MPEG Field : Any Bytes per Line: 0 Size Image : 58656 Colorspace : Unknown (00000000) Video input : 0 (CCIR656) Video Standard = 0x000000ff PAL-B/B1/G/H/I/D/D1/K P.S. data from /dev/video1 is not correct :(( . Signed-off-by: Beholder Intl. Ltd. Dmitry Belimov <d.belimov@gmail.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
2008-06-26V4L/DVB (8018): Add em2860 chip IDDevin Heitmueller
em28xx-cards.c em28xx-reg.h - Add em2860 chip ID (seen on Pointnix Intra-Oral Camera) http://www.pointnix.com/ENG/dental/product_02.asp Signed-off-by: Devin Heitmueller <devin.heitmueller@gmail.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
2008-06-26V4L/DVB (8017): Ensure em28xx extensions only get run against devs that ↵Devin Heitmueller
support them em28xx-audio.c em28xx-dvb.c - Em28xx extensions should ensure they are being only loaded against devices that support them. Deals with case where there are multiple em28xx devices, some of which have DVB (or ALSA) support and some do not. Signed-off-by: Devin Heitmueller <devin.heitmueller@gmail.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
2008-06-26V4L/DVB (8015): gl861: replace non critical msleep(0) with msleep(1) to be ↵Antti Palosaari
on the safe side - change msleep(0) to msleep(1) Signed-off-by: Antti Palosaari <crope@iki.fi> Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
2008-06-26V4L/DVB (8013): gl861: remove useless identify_stateAntti Palosaari
- remove useless identify_state - device is always warm Signed-off-by: Antti Palosaari <crope@iki.fi> Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
2008-06-26V4L/DVB (8012): gl861: sleep a little to avoid I2C errorsAntti Palosaari
- add little sleep to avoid I2C errors arising on faster CPUs Signed-off-by: Antti Palosaari <crope@iki.fi> Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
2008-06-26V4L/DVB (8011): em28xx: enable DVB for HVR-900Devin Heitmueller
em28xx-cards.c - DVB support is supposed to be enabled for the first generation HVR-900. This device was confirmed with DVB by mkrufky when we did the original work in April, but I guess we forgot to set the flag. Signed-off-by: Devin Heitmueller <devin.heitmueller@gmail.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
2008-06-26V4L/DVB (8010): em28xx: Properly register extensions for already attached ↵Devin Heitmueller
devices em28xx-video.c - Properly handle loading of the module when multiple devices are already connected (such as at bootup). Before we were only calling dvb_init() against the last device in the list, so while we were handling subsequent adds properly, if there were multiple devices present on driver load, everybody except the last device would not get initialized. Signed-off-by: Devin Heitmueller <devin.heitmueller@gmail.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
2008-06-26V4L/DVB (8008): cx18: remove duplicate audio and video input enumsHans Verkuil
cx18-cards.h had a copy of the audio and video input enums from cx18-av-core.h, but with different prefixes. Removed that copy and used the ones from cx18-av-core.h. Thanks to Andy Walls <awalls@radix.net> for the report. Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
2008-06-26V4L/DVB (8007): cx18/cx25840: the S-Video LUMA input can use all In1-In8 inputsHans Verkuil
The S-Video LUMA input was restricted to the In1-In4 inputs, but it turns out that it can use the full range of In1-In8. Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
2008-06-26V4L/DVB (8005): Fix OOPS if frontend is nullMauro Carvalho Chehab
Thanks to timf <timf@iinet.net.au> and Mike Galbraith <efault@gmx.de> to report this issue. Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
2008-06-26V4L/DVB (8004): Fix INPUT dependency at budget-ciMauro Carvalho Chehab
As reported by Ingo Molnar: MODPOST 346 modules ERROR: "input_free_device" [drivers/media/dvb/ttpci/budget-ci.ko] undefined! ERROR: "input_register_device" [drivers/media/dvb/ttpci/budget-ci.ko] undefined! ERROR: "input_allocate_device" [drivers/media/dvb/ttpci/budget-ci.ko] undefined! ERROR: "input_unregister_device" [drivers/media/dvb/ttpci/budget-ci.ko] undefined! ERROR: "input_event" [drivers/media/common/ir-common.ko] undefined! This occurs when: CONFIG_INPUT=n CONFIG_VIDEO_IR=m CONFIG_DVB_BUDGET_CI=m Thanks-to: Ingo Molnar <mingo@elte.hu> Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
2008-06-24Linux 2.6.26-rc8Linus Torvalds
2008-06-24Merge branch 'release' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/aegl/linux-2.6 * 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/aegl/linux-2.6: [IA64] Eliminate NULL test after alloc_bootmem in iosapic_alloc_rte() [IA64] Handle count==0 in sn2_ptc_proc_write() [IA64] Fix boot failure on ia64/sn2
2008-06-24Merge git://git.kernel.org/pub/scm/linux/kernel/git/steve/gfs2-2.6-fixesLinus Torvalds
* git://git.kernel.org/pub/scm/linux/kernel/git/steve/gfs2-2.6-fixes: [GFS2] fix gfs2 block allocation (cleaned up) [GFS2] BUG: unable to handle kernel paging request at ffff81002690e000
2008-06-24Merge branch 'kvm-updates-2.6.26' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/avi/kvm * 'kvm-updates-2.6.26' of git://git.kernel.org/pub/scm/linux/kernel/git/avi/kvm: KVM: Remove now unused structs from kvm_para.h x86: KVM guest: Use the paravirt clocksource structs and functions KVM: Make kvm host use the paravirt clocksource structs x86: Make xen use the paravirt clocksource structs and functions x86: Add structs and functions for paravirt clocksource KVM: VMX: Fix host msr corruption with preemption enabled KVM: ioapic: fix lost interrupt when changing a device's irq KVM: MMU: Fix oops on guest userspace access to guest pagetable KVM: MMU: large page update_pte issue with non-PAE 32-bit guests (resend) KVM: MMU: Fix rmap_write_protect() hugepage iteration bug KVM: close timer injection race window in __vcpu_run KVM: Fix race between timer migration and vcpu migration
2008-06-24Merge git://git.kernel.org/pub/scm/linux/kernel/git/wim/linux-2.6-watchdogLinus Torvalds
* git://git.kernel.org/pub/scm/linux/kernel/git/wim/linux-2.6-watchdog: Revert "[WATCHDOG] hpwdt: Add CFLAGS to get driver working"
2008-06-24Merge branch 'x86-fixes-for-linus' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip * 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: xen: remove support for non-PAE 32-bit
2008-06-24Merge branch 'for_linus' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/jwessel/linux-2.6-kgdb * 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jwessel/linux-2.6-kgdb: kgdb: sparse fix kgdb: documentation update - remove kgdboe
2008-06-24enable bus mastering on i915 at resume timeJie Luo
On 9xx chips, bus mastering needs to be enabled at resume time for much of the chip to function. With this patch, vblank interrupts will work as expected on resume, along with other chip functions. Fixes kernel bugzilla #10844. Signed-off-by: Jie Luo <clotho67@gmail.com> Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-06-24KVM: Remove now unused structs from kvm_para.hGerd Hoffmann
The kvm_* structs are obsoleted by the pvclock_* ones. Now all users have been switched over and the old structs can be dropped. Signed-off-by: Gerd Hoffmann <kraxel@redhat.com> Signed-off-by: Avi Kivity <avi@qumranet.com>
2008-06-24x86: KVM guest: Use the paravirt clocksource structs and functionsGerd Hoffmann
This patch updates the kvm host code to use the pvclock structs and functions, thereby making it compatible with Xen. The patch also fixes an initialization bug: on SMP systems the per-cpu has two different locations early at boot and after CPU bringup. kvmclock must take that in account when registering the physical address within the host. Signed-off-by: Gerd Hoffmann <kraxel@redhat.com> Signed-off-by: Avi Kivity <avi@qumranet.com>
2008-06-24KVM: Make kvm host use the paravirt clocksource structsGerd Hoffmann
This patch updates the kvm host code to use the pvclock structs. It also makes the paravirt clock compatible with Xen. Signed-off-by: Gerd Hoffmann <kraxel@redhat.com> Signed-off-by: Avi Kivity <avi@qumranet.com>
2008-06-24x86: Make xen use the paravirt clocksource structs and functionsGerd Hoffmann
This patch updates the xen guest to use the pvclock structs and helper functions. Signed-off-by: Gerd Hoffmann <kraxel@redhat.com> Acked-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com> Signed-off-by: Avi Kivity <avi@qumranet.com>
2008-06-24x86: Add structs and functions for paravirt clocksourceGerd Hoffmann
This patch adds structs for the paravirt clocksource ABI used by both xen and kvm (pvclock-abi.h). It also adds some helper functions to read system time and wall clock time from a paravirtual clocksource (pvclock.[ch]). They are based on the xen code. They are enabled using CONFIG_PARAVIRT_CLOCK. Subsequent patches of this series will put the code in use. Signed-off-by: Gerd Hoffmann <kraxel@redhat.com> Acked-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com> Signed-off-by: Avi Kivity <avi@qumranet.com>
2008-06-24[GFS2] fix gfs2 block allocation (cleaned up)Benjamin Marzinski
This patch fixes bz 450641. This patch changes the computation for zero_metapath_length(), which it renames to metapath_branch_start(). When you are extending the metadata tree, The indirect blocks that point to the new data block must either diverge from the existing tree either at the inode, or at the first indirect block. They can diverge at the first indirect block because the inode has room for 483 pointers while the indirect blocks have room for 509 pointers, so when the tree is grown, there is some free space in the first indirect block. What metapath_branch_start() now computes is the height where the first indirect block for the new data block is located. It can either be 1 (if the indirect block diverges from the inode) or 2 (if it diverges from the first indirect block). Signed-off-by: Benjamin Marzinski <bmarzins@redhat.com> Signed-off-by: Steven Whitehouse <swhiteho@redhat.com>
2008-06-24[IA64] Eliminate NULL test after alloc_bootmem in iosapic_alloc_rte()Julia Lawall
As noted by Akinobu Mita alloc_bootmem and related functions never return NULL and always return a zeroed region of memory. Thus a NULL test or memset after calls to these functions is unnecessary. Signed-off-by: Julia Lawall <julia@diku.dk> Signed-off-by: Tony Luck <tony.luck@intel.com>
2008-06-24[IA64] Handle count==0 in sn2_ptc_proc_write()Cliff Wickman
The fix applied in e0c6d97c65e0784aade7e97b9411f245a6c543e7 "security hole in sn2_ptc_proc_write" didn't take into account the case where count==0 (which results in a buffer underrun when adding the trailing '\0'). Thanks to Andi Kleen for pointing this out. Signed-off-by: Cliff Wickman <cpw@sgi.com> Signed-off-by: Tony Luck <tony.luck@intel.com>
2008-06-24[IA64] Fix boot failure on ia64/sn2Jes Sorensen
Call check_sal_cache_flush() after platform_setup() as check_sal_cache_flush() now relies on being able to call platform vector code. Problem was introduced by: 3463a93def55c309f3c0d0a8aaf216be3be42d64 "Update check_sal_cache_flush to use platform_send_ipi()" Signed-off-by: Jes Sorensen <jes@sgi.com> Tested-by: Alex Chiang: <achiang@hp.com> Signed-off-by: Tony Luck <tony.luck@intel.com>
generated by cgit v1.2.3 (git 2.25.1) at 2024-11-11 08:44:18 +0000