| Age | Commit message (Collapse) | Author |
|---|
|
Some of the rate selection logic in s3c64xx_setrate_clksrc uses what
appears to be parent clock selection logic. This patch corrects it.
I also added a check for overly large dividers to prevent them from
changing unrelated clocks.
Signed-off-by: Werner Almesberger <werner@openmoko.org>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
|
|
Fix the following sparse warnings in arch/arm/plat-s3c64xx/irq.c
arch/arm/plat-s3c64xx/irq.c:210:23: warning: incorrect type in initializer (different address spaces)
arch/arm/plat-s3c64xx/irq.c:210:23: expected void *reg_base
arch/arm/plat-s3c64xx/irq.c:210:23: got void [noderef] <asn:2>*regs
arch/arm/plat-s3c64xx/irq.c:215:2: warning: incorrect type in argument 1 (different address spaces)
arch/arm/plat-s3c64xx/irq.c:215:2: expected void const volatile [noderef] <asn:2>*<noident>
arch/arm/plat-s3c64xx/irq.c:215:2: got void *
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
|
|
Fix the following sparse warnings in s3c6400-clock.c:
39:12: warning: symbol 'clk_ext_xtal_mux' was not declared. Should it be static?
66:12: warning: symbol 'clk_fout_apll' was not declared. Should it be static?
81:19: warning: symbol 'clk_mout_apll' was not declared. Should it be static?
91:12: warning: symbol 'clk_fout_epll' was not declared. Should it be static?
106:19: warning: symbol 'clk_mout_epll' was not declared. Should it be static?
126:19: warning: symbol 'clk_mout_mpll' was not declared. Should it be static?
148:12: warning: symbol 'clk_dout_mpll' was not declared. Should it be static?
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
|
|
The clock list for the USB host bus clock was in the wrong order,
move clk_48m to position 0.
Signed-off-by: Ben Dooks <ben@simtec.co.uk>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
|
|
The usb-host-bus clock should be named usb-bus-host.
Signed-off-by: Ben Dooks <ben@simtec.co.uk>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
|
|
The USB OHCI host device expects the IRQ definition to be named
IRQ_USBH, so rename the S3C64XX IRQ header to match.
Signed-off-by: Ben Dooks <ben@simtec.co.uk>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
|
|
arch_initcall() runs after the machine init function which means that
any configuration of GPIO pins must currently be done later on, for
example in callbacks from drivers. Move the initialisation earlier in
order to allow machines to configure GPIOs directly in their init
functions rather than having to have a callback invoked later on.
Some other ARM platforms use this method. Other solutions for this
include providing a special interface for setting up GPIOs en masse,
adding callbacks to do the GPIO configuration from devices and doing
the GPIO configuration implicitly.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
|
|
It's an initcall and does not need to be exported.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
|
|
Shuts up a warning.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
|
|
The WM8580 driver registers itself as "wm8580" rather than "WM8580".
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
|
|
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
|
|
Set the GPIO pin mode to external interrupt when configuring
an IRQ_EINT's IRQ type.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
|
|
|
|
Add missing parameter value to list of available values
for acpi=<value>.
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6
* 'drm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6:
drm/i915: Add missing mutex_lock(&dev->struct_mutex)
drm/i915: fix WC mapping in non-GEM i915 code.
drm/i915: Fix regression in 95ca9d
drm/i915: Retire requests from i915_gem_busy_ioctl.
drm/i915: suspend/resume GEM when KMS is active
drm/i915: Don't let a device flush to prepare buffers clear new write_domains.
drm/i915: Cut two args to set_to_gpu_domain that confused this tricky path.
|
|
there might be a nicer way to fix this but this is the simplest for now.
Signed-off-by: Pierre Willenbrock <pierre@pirsoft.de>
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
[airlied - taken from mailing list posting]
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
The object is dereferenced before the NULL check. Oops.
Fixes http://bugs.freedesktop.org/show_bug.cgi?id=20235
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
This ensures that the user gets the latest information from the hardware
on whether the buffer is busy, potentially reducing the working set of objects
that the user chooses.
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
In the KMS case, we need to suspend/resume GEM as well. So on suspend, make
sure we idle GEM and stop any new rendering from coming in, and on resume,
re-init the framebuffer and clear the suspended flag.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
The problem was that object_set_to_gpu_domain would set the new write_domains
that are getting set by this batchbuffer, then the accumulated flushes required
for all the objects in preparation for this batchbuffer were posted, and the
brand new write domain would get cleared by the flush being posted. Instead,
hang on to the new (or old if we're not changing it) value and set it after
the flush is queued.
Results from this noticably included conformance test failures from reads
shortly after writes (where the new write domain had been lost and thus not
flushed and waited on), but is a suspected cause of hangs in some apps when
a write domain is lost on a buffer that gets reused for instruction or
commmand state.
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
While not strictly required, it helped while thinking about the following
change. This change should be invariant.
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
At some point we (okay, I) managed to break the ability for users to use the
setsockopt() syscall to set IPv4 options when NetLabel was not active on the
socket in question. The problem was noticed by someone trying to use the
"-R" (record route) option of ping:
# ping -R 10.0.0.1
ping: record route: No message of desired type
The solution is relatively simple, we catch the unlabeled socket case and
clear the error code, allowing the operation to succeed. Please note that we
still deny users the ability to override IPv4 options on socket's which have
NetLabel labeling active; this is done to ensure the labeling remains intact.
Signed-off-by: Paul Moore <paul.moore@hp.com>
Signed-off-by: James Morris <jmorris@namei.org>
|
|
The CIPSO protocol engine incorrectly stated that the FIPS-188 specification
could be found in the kernel's Documentation directory. This patch corrects
that by removing the comment and directing users to the FIPS-188 documented
hosted online. For the sake of completeness I've also included a link to the
CIPSO draft specification on the NetLabel website.
Thanks to Randy Dunlap for spotting the error and letting me know.
Signed-off-by: Paul Moore <paul.moore@hp.com>
Signed-off-by: James Morris <jmorris@namei.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip
* 'core/urgent' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
PM: Split up sysdev_[suspend|resume] from device_power_[down|up], fix
|
|
Impact: module build fix
Fix:
ERROR: "sysdev_resume" [arch/x86/kernel/apm.ko] undefined!
ERROR: "sysdev_suspend" [arch/x86/kernel/apm.ko] undefined!
As these APIs are now used by the APM driver, which can be built
as a module.
Also fix a few extra (and inconsistent) newlines in comment blocks
preceding these functions.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
The kernel-api docbook was much larger than any of the others,
so processing it took longer and needed some docbook extras in
some cases, so split it into kernel-api (infrastructure etc.)
and device drivers/device subsystems. This allows these docbooks
to be generated in parallel. (This reduced the docbook processing
time on my 4-proc system with make -j4 from about 5min:16sec to
about 2min:01sec.)
The chapters that were moved from kernel-api to device-drivers are:
Driver Basics
Device drivers infrastructure
Parallel Port Devices
Message-based devices
Sound Devices
16x50 UART Driver
Frame Buffer Library
Input Subsystem
Serial Peripheral Interface (SPI)
I2C and SMBus Subsystem
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Move the sysdev_suspend/resume from the callee to the callers, with
no real change in semantics, so that we can rework the disabling of
interrupts during suspend/hibernation.
This is based on an earlier patch from Linus.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Right now nobody cares, but the suspend/resume code will eventually want
to suspend device interrupts without suspending the timer, and will
depend on this flag to know.
The modern x86 timer infrastructure uses the local APIC timers and never
shows up as a device interrupt at all, so it isn't affected and doesn't
need any of this.
Cc: Rafael J. Wysocki <rjw@sisk.pl>
Cc: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-acpi-2.6
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-acpi-2.6:
ACPI: remove CONFIG_ACPI_SYSTEM
fujitsu-laptop: Use RFKILL support bitmask from firmware
x86_64: Fix S3 fail path
x86_64: acpi/wakeup_64 cleanup
battery: don't assume we are fully charged when not charging or discharging
ACPI: EC: Add delay for slow MSI controller
|
|
attributes
Fix descriptions of device attributes to be consistent with the actual
implementations in include/linux/device.h
Signed-off-by: Mike Murphy <mamurph[at]cs.clemson.edu>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Fix the presented definition of struct device_attribute to match the
actual definition in include/linux/device.h
Signed-off-by: Mike Murphy <mamurph[at]cs.clemson.edu>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
http://kisskb.ellerman.id.au/kisskb/buildresult/72115/:
| net/mac80211/ieee80211_i.h:327: error: syntax error before 'volatile'
| net/mac80211/ieee80211_i.h:350: error: syntax error before '}' token
| net/mac80211/ieee80211_i.h:455: error: field 'sta' has incomplete type
| distcc[19430] ERROR: compile net/mac80211/main.c on sprygo/32 failed
This is caused by
| # define mfp ((*(volatile struct MFP*)MFP_BAS))
in arch/m68k/include/asm/atarihw.h, which conflicts with the new "mfp" enum in
net/mac80211/ieee80211_i.h.
Rename "mfp" to "st_mfp", as it's a way too generic name for a global #define.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
'suspend' into release
|
|
Remove CONFIG_ACPI_SYSTEM. It was always set the same as CONFIG_ACPI,
and it had no menu label, so there was no way to set it to anything
other than "y".
Some things under CONFIG_ACPI_SYSTEM (acpi_irq_handled, acpi_os_gpe_count(),
event_is_open, register_acpi_notifier(), etc.) are used unconditionally
by the CA, the OSPM, and drivers, so we depend on them always being
present.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Len Brown <len.brown@intel.com>
|
|
Up until now, we polled the rfkill status for every incoming FUJ02E3 ACPI event.
It turns out that the firmware has a bitmask which indicates what rfkill-related
state it can report.
The rfkill_supported bitmask is now used to avoid polling for rfkill at all in
the notification handler if there is no support. Also, it is used in the platform
device callbacks. As before we register all callbacks and report "unknown" if the
firmware does not give us status updates for that particular bit.
This was fed through checkpatch.pl and tested on the S6420, S7020 and P8010
platforms.
Signed-off-by: Tony Vroon <tony@linx.net>
Tested-by: Stephen Gildea <stepheng+linux@gildea.com>
Acked-by: Jonathan Woithe <jwoithe@physics.adelaide.edu.au>
Signed-off-by: Len Brown <len.brown@intel.com>
|
|
As acpi_enter_sleep_state can fail, take this into account in
do_suspend_lowlevel and don't return to the do_suspend_lowlevel's
caller. This would break (currently) fpu status and preempt count.
Technically, this means use `call' instead of `jmp' and `jmp' to
the `resume_point' after the `call' (i.e. if
acpi_enter_sleep_state returns=fails). `resume_point' will handle
the restore of fpu and preempt count gracefully.
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Len Brown <len.brown@intel.com>
|
|
- remove %ds re-set, it's already set in wakeup_long64
- remove double labels and alignment (ENTRY already adds both)
- use meaningful resume point labelname
- skip alignment while jumping from wakeup_long64 to the resume point
- remove .size, .type and unused labels
[v2]
- added ENDPROCs
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Acked-by: Cyrill Gorcunov <gorcunov@openvz.org>
Acked-by: Pavel Machek <pavel@suse.cz>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Len Brown <len.brown@intel.com>
|
|
* hibernate:
PM: Fix suspend_console and resume_console to use only one semaphore
PM: Wait for console in resume
PM: Fix pm_notifiers during user mode hibernation
swsusp: clean up shrink_all_zones()
swsusp: dont fiddle with swappiness
PM: fix build for CONFIG_PM unset
PM/hibernate: fix "swap breaks after hibernation failures"
PM/resume: wait for device probing to finish
Consolidate driver_probe_done() loops into one place
|
|
This fixes a race where a thread acquires the console while the
console is suspended, and the console is resumed before this
thread releases it. In this case, the secondary console
semaphore would be left locked, and the primary semaphore would
be released twice. This in turn would cause the console switch
on suspend or resume to hang forever.
Note that suspend_console does not actually lock the console
for clients that use acquire_console_sem, it only locks it for
clients that use try_acquire_console_sem. If we change
suspend_console to fully lock the console, then the kernel
may deadlock on suspend. One client of try_acquire_console_sem
is acquire_console_semaphore_for_printk, which uses it to
prevent printk from using the console while it is suspended.
Signed-off-by: Arve Hjønnevåg <arve@android.com>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Cc: Len Brown <lenb@kernel.org>
Cc: Greg KH <gregkh@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Avoids later waking up to a blinking cursor if the device woke up and
returned to sleep before the console switch happened.
Signed-off-by: Brian Swetland <swetland@google.com>
Signed-off-by: Arve Hjønnevåg <arve@android.com>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Cc: Len Brown <lenb@kernel.org>
Cc: Greg KH <gregkh@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Snapshot device is opened with O_RDONLY during suspend and O_WRONLY durig
resume. Make sure we also call notifiers with correct parameter telling
them what we are really doing.
Signed-off-by: Andrey Borzenkov <arvidjaar@mail.ru>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Cc: Len Brown <lenb@kernel.org>
Cc: Greg KH <gregkh@suse.de>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Move local variables to innermost possible scopes and use local
variables to cache calculations/reads done more than once.
No change in functionality (intended).
Signed-off-by: Johannes Weiner <hannes@cmpxchg.org>
Reviewed-by: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Cc: Len Brown <lenb@kernel.org>
Cc: Greg KH <gregkh@suse.de>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
sc.swappiness is not used in the swsusp memory shrinking path, do not
set it.
Signed-off-by: Johannes Weiner <hannes@cmpxchg.org>
Reviewed-by: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Cc: Len Brown <lenb@kernel.org>
Cc: Greg KH <gregkh@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Compilation of kprobes.c with CONFIG_PM unset is broken due to some broken
config dependncies. Fix that.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Cc: Len Brown <lenb@kernel.org>
Cc: Greg KH <gregkh@suse.de>
Reported-by: Ingo Molnar <mingo@elte.hu>
Tested-by: Masami Hiramatsu <mhiramat@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
http://bugzilla.kernel.org/show_bug.cgi?id=12239
The image writing code dropped a reference to the current swap device.
This doesn't show up if the hibernation succeeds - because it doesn't
affect the image which gets resumed. But it means multiple _failed_
hibernations end up freeing the swap device while it is still use!
swsusp_write() finds the block device for the swap file using swap_type_of().
It then uses blkdev_get() / blkdev_put() to open and close the block device.
Unfortunately, blkdev_get() assumes ownership of the inode of the block_device
passed to it. So blkdev_put() calls iput() on the inode. This is by design
and other callers expect this behaviour. The fix is for swap_type_of() to take
a reference on the inode using bdget().
Signed-off-by: Alan Jenkins <alan-jenkins@tuffmail.co.uk>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Cc: Len Brown <lenb@kernel.org>
Cc: Greg KH <gregkh@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
the resume code does not currently wait for device probing to finish.
Even without async function calls this is dicey and not correct,
but with async function calls during the boot sequence this is going
to get hit more...
This patch adds the synchronization using the newly introduced helper.
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Cc: Len Brown <lenb@kernel.org>
Acked-by: Greg KH <gregkh@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
there's a few places that currently loop over driver_probe_done(), and
I'm about to add another one. This patch abstracts it into a helper
to reduce duplication.
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Cc: Len Brown <lenb@kernel.org>
Acked-by: Greg KH <gregkh@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
On hardware like the T61 it can take a couple of seconds for the battery
to start charging after the power is connected, and we incorrectly tell
userspace that we are fully charged, and then go back to charging.
Only mark a battery as fully charged when the preset charge matches either
the last full charge, or the design charge.
http://bugzilla.kernel.org/show_bug.cgi?id=12632
Signed-off-by: Richard Hughes <hughsient@gmail.com>
Acked-by: Alexey Starikovskiy <astarikovskiy@suse.de>
Acked-by: Henrique de Moraes Holschuh <hmh@hmh.eng.br>
Signed-off-by: Len Brown <len.brown@intel.com>
|
|
http://bugzilla.kernel.org/show_bug.cgi?id=12011
Signed-off-by: Alexey Starikovskiy <astarikovskiy@suse.de>
Signed-off-by: Len Brown <len.brown@intel.com>
|
