Age | Commit message (Collapse) | Author |
|
If no prior break occurs, cnt reaches 101 after the loop, so we are still able
to change speed when cnt has become 100.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Remove workaround for pcie bug in early revisions of NX3031
(rev 41 or earlier). This is taken care of during firmware init.
The workaround required writing pcie config reg of every
pcie function on a card, not all of which are enabled.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
With while (--i > 0) { ... } i reaches 0; print when lance_open() fails
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The large receive buffer queue is not properly tracking the current
index in the case where an early exit occurs. This can happen when a
page alloc or dma mapping fails. If this occurs the queue will get
out of sync and invalid indexes can be written to the hardware.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Receive packets were only scaling across 2 of the receive queues. The
value was hardcoded to 2 instead of being based on how many rx queues
were running.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Moved the buffer mapping to a point after TSO logic has modified the
iph->check field. We were seeing stale data on the PCIe bus.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We put the skb back if we can't get mapping for it. We don't
want unmapped buffers on our receive buffer queue.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We put the page back if we can't get mapping for it. We don't
want unmapped buffers on our receive buffer queue.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Replace calls to vlan_hwaccel_rx() and netif_rx().
Thanks to Dave Miller for pointing out the the driver was making
the wrong upcall for passing packets into the stack.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
With while (limit--) { ... } limit reaches -1, so 0 means success.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Acked-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Here we do two things:
First, revert "iwlwifi: save PCI state before suspend, restore after
resume". That misguided patch led to being unable to use iwlwifi
devices after resume.
Next, indicate to PCI driver that the saved PCI state is valid during suspend.
We restore PCI state and enable the device when network interface is created,
similarly PCI state is saved and the device is disabled when network interface
is removed. Thus, when .suspend is called the PCI state is saved and device
is disabled. This is the case even if an interface is never created as PCI
state is saved and device disabled during .probe.
PCI driver assumes PCI state is saved in .suspend. Saving the state at this
time will save state of disabled device and thus cause problems during
resume (resuming a disabled device). We thus indicate directly to PCI
driver that current PCI saved state is valid.
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Tested-by: Alex Riesen <fork0@users.sf.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Three people (Petr Mensik <pihhan@cipis.net>
["si" should be U+0161 U+00ED], Stephen Ho <stephenhoinhk@gmail.com>
on zd1211-devs and Ismael Ojeda Perez <iojedaperez@gmail.com>
on linux-wireless) reported success in getting TP-Link WN322G/WN422G
working by treating MAXIM_NEW_RF(0x08) as UW2453_RF(0x09) for rf
chip hardware initialization.
Signed-off-by: Hin-Tak Leung <htl10@users.sourceforge.net>
Tested-by: Petr Mensik <pihhan@cipis.net>
Tested-by: Stephen Ho <stephenhoinhk@gmail.com>
Tested-by: Ismael Ojeda Perez <iojedaperez@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Christoph Biedl <sourceforge.bnwi@manchmal.in-ulm.de> reported success
in the sourceforge zd1211 mailing list on this addition. This product ID
was supported by the vendor driver ZD1211LnxDrv 2.22.0.0 (and possibly
earlier) and it probably should have been added earlier.
Signed-off-by: Hin-Tak Leung <htl10@users.sourceforge.net>
Tested-by: Christoph Biedl <sourceforge.bnwi@manchmal.in-ulm.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
We try to find the correct outgoing interface for injected frames
based on the TA, but since this is a hack for hostapd 11w, restrict
the heuristic to AP mode interfaces. At some point we'll add the
ability to give an interface index in radiotap or so and just
remove this heuristic again.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Cc: stable@kernel.org [2.6.28.x]
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Under memory pressure, we may not be able to allocate a new skb for
new packets. If the allocation fails, ath5k_tasklet_rx will exit but
will leave a buffer in the list with a NULL skb, eventually triggering
a BUG_ON.
Extract the skb allocation from ath5k_rxbuf_setup() and change the
tasklet to allocate the next skb before accepting a packet.
Changes-licensed-under: 3-Clause-BSD
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Currently, the sunhme driver installs SBus Quattro interrupt handler
when at least one HME card was initialized correctly and at least one
Quattro card is present. This breaks when a Quattro card fails
initialization for whatever reason - IRQ is registered and OOPS happens
when it fires.
The solution, as suggested by David Miller, was to keep track which
cards of the Quattro bundles have been initialized, and request/free the
Quattro IRQ only when all four devices have been successfully
initialized.
The patch only touches SBus initialization - PCI init already resets the
card pointer to NULL on init failure.
The patch has been tested on Sun E3500 with SBus and PCI single HME
cards and one PCI Quattro HME card in a situation where any PCI card
failed init when the SBus routines tried to init them by mistake.
Additionally it replaces Quattro request_irq panic with error return -
if this card fails to work, at least let the others work.
Tested on E450 with PCI HME and PCI Quad HME.
[ Minor coding style fixups -DaveM ]
Signed-off-by: Meelis Roos <mroos@linux.ee>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fore 200 ATM driver fails to handle request_firmware failures and oopses
when no firmware file was found. Fix it by checking for the right return
values and propaganting the return value up.
Signed-off-by: Meelis Roos <mroos@linux.ee>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Using u32 in this header breaks the build of iptables.
Signed-off-by: Chuck Ebbert <cebbert@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Rémi Denis-Courmont <remi.denis-courmont@nokia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Rémi Denis-Courmont <remi.denis-courmont@nokia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
mdc pin should always be output. Initialize it as output,
so each board code does not need to do this.
Signed-off-by: Paulius Zaleckas <paulius.zaleckas@teltonika.lt>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
> Kernel BUG at drivers/net/tun.c:444
> invalid opcode: 0000 [1] SMP
> last sysfs file: /class/net/lo/ifindex
> CPU 0
> Modules linked in: tun ipt_MASQUERADE iptable_nat ip_nat xt_state ip_conntrack
> nfnetlink ipt_REJECT xt_tcpudp iptable_filter d
> Pid: 6912, comm: qemu-kvm Tainted: G 2.6.18-128.el5 #1
> RIP: 0010:[<ffffffff886f57b0>] [<ffffffff886f57b0>]
> :tun:tun_chr_readv+0x2b1/0x3a6
> RSP: 0018:ffff8102202c5e48 EFLAGS: 00010246
> RAX: 0000000000000000 RBX: ffff8102202c5e98 RCX: 0000000004010000
> RDX: ffff810227063680 RSI: ffff8102202c5e9e RDI: ffff8102202c5e92
> RBP: 0000000000010ff6 R08: 0000000000000000 R09: 0000000000000001
> R10: ffff8102202c5e94 R11: 0000000000000202 R12: ffff8102275357c0
> R13: ffff81022755e500 R14: 0000000000000000 R15: ffff8102202c5ef8
> FS: 00002ae4398db980(0000) GS:ffffffff803ac000(0000) knlGS:0000000000000000
> CS: 0010 DS: 0000 ES: 0000 CR0: 000000008005003b
> CR2: 00002ae4ab514000 CR3: 0000000221344000 CR4: 00000000000026e0
> Process qemu-kvm (pid: 6912, threadinfo ffff8102202c4000, task
> ffff81022e58d820)
> Stack: 00000000498735cb ffff810229d1a3c0 0000000000000000 ffff81022e58d820
> ffffffff8008a461 ffff81022755e528 ffff81022755e528 ffffffff8009f925
> 000005ea05ea0000 ffff8102209d0000 00001051143e1600 ffffffff8003c00e
> Call Trace:
> [<ffffffff8008a461>] default_wake_function+0x0/0xe
> [<ffffffff8009f925>] enqueue_hrtimer+0x55/0x70
> [<ffffffff8003c00e>] hrtimer_start+0xbc/0xce
> [<ffffffff886f58bf>] :tun:tun_chr_read+0x1a/0x1f
> [<ffffffff8000b3f3>] vfs_read+0xcb/0x171
> [<ffffffff800117d4>] sys_read+0x45/0x6e
> [<ffffffff8005d116>] system_call+0x7e/0x83
>
>
> Code: 0f 0b 68 40 62 6f 88 c2 bc 01 f6 42 0a 08 74 0c 80 4c 24 41
> RIP [<ffffffff886f57b0>] :tun:tun_chr_readv+0x2b1/0x3a6
> RSP <ffff8102202c5e48>
> <0>Kernel panic - not syncing: Fatal exception
This crashed when an LRO packet generated by bnx2x reached a
tun device through the bridge. We're supposed to drop it at
the bridge. However, because the check was placed in br_forward
instead of __br_forward, it's only effective if we are sending
the packet through a single port.
This patch fixes it by moving the check into __br_forward.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When the user creates IPv6 over IPv6 tunnel, the device name created
by the kernel isn't set to t->parm.name, which is referred as the
result of ioctl().
Signed-off-by: Noriaki TAKAMIYA <takamiya@po.ntts.co.jp>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Ira Snyder found that commit 8c7396aebb68994c0519e438eecdf4d5fa9c7844
"gianfar: Merge Tx and Rx interrupt for scheduling clean up ring" can
cause hangs. It's because there was removed clearing of interrupts in
gfar_schedule_cleanup() (which is called by an interrupt handler) in
case when netif scheduling has been disabled. This patch brings back
this action and a comment.
Reported-by: Ira Snyder <iws@ovro.caltech.edu>
Reported-by: Peter Korsgaard <jacmet@sunsite.dk>
Bisected-by: Ira Snyder <iws@ovro.caltech.edu>
Tested-by: Peter Korsgaard <jacmet@sunsite.dk>
Tested-by: Ira Snyder <iws@ovro.caltech.edu>
Signed-off-by: Jarek Poplawski <jarkao2@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When user tries to map all chunks given in argument, kernel
works on a copy of the chunkmap, but at the end it doesn't
check the copy, but the orginal one.
Signed-off-by: Qu Haoran <haoran.qu@6wind.com>
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch fixes echoing if the socket that has sent the request to
create/update/delete an entry is not subscribed to any multicast
group. With the current code, ctnetlink would not send the echo
message via unicast as nfnetlink_send() would be skip.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch fixes an inconsistency in the current ctnetlink code
since NAT sequence adjustment bit can only be updated but not set
in the conntrack entry creation.
This patch is used by conntrackd to successfully recover newly
created entries that represent connections with helpers and NAT
payload mangling.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch removes connection tracking handling for ICMPv6 messages
related to Stateless Address Autoconfiguration, MLD, and MLDv2. They
can not be tracked because they are massively using multicast (on
pre-defined address). But they are not invalid and should not be
detected as such.
Signed-off-by: Eric Leblond <eric@inl.fr>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The patch fixes a typo in the inverse mapping of Node Information
request. Following draft-ietf-ipngwg-icmp-name-lookups-09, "Querier"
sends a type 139 (ICMPV6_NI_QUERY) packet to "Responder" which answer
with a type 140 (ICMPV6_NI_REPLY) packet.
Signed-off-by: Eric Leblond <eric@inl.fr>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
o Cut down msi-x vectors from 8 to 1 since only one is used for now.
o Use separate handler for msi-x, that doesn't unnecessarily scrub
msi status register.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
DescOwn should not be set, thus allowing the chip to use the
descriptor, before everything else is set up correctly.
Signed-off-by: Risto Suominen <Risto.Suominen@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Tap devices can make use of a small MAC filter set via the
TUNSETTXFILTER ioctl. The filter has a set of exact matches
plus a hash for imperfect filtering of additional multicast
addresses. The current code is unbalanced, adding unicast
addresses to the multicast hash, but only checking the hash
against multicast addresses. This results in the filter
dropping unicast addresses that overflow the exact filter.
The fix is simply to disable the filter by leaving count set
to zero if we find non-multicast addresses after the exact
match table is filled.
Signed-off-by: Alex Williamson <alex.williamson@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Error handling code following a kmalloc should free the allocated data.
The semantic match that finds the problem is as follows:
(http://www.emn.fr/x-info/coccinelle/)
// <smpl>
@r exists@
local idexpression x;
statement S;
expression E;
identifier f,l;
position p1,p2;
expression *ptr != NULL;
@@
(
if ((x@p1 = \(kmalloc\|kzalloc\|kcalloc\)(...)) == NULL) S
|
x@p1 = \(kmalloc\|kzalloc\|kcalloc\)(...);
...
if (x == NULL) S
)
<... when != x
when != if (...) { <+...x...+> }
x->f = E
...>
(
return \(0\|<+...x...+>\|ptr\);
|
return@p2 ...;
)
@script:python@
p1 << r.p1;
p2 << r.p2;
@@
print "* file: %s kmalloc %s return %s" % (p1[0].file,p1[0].line,p2[0].line)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Error handling code following a kmalloc should free the allocated data.
The semantic match that finds the problem is as follows:
(http://www.emn.fr/x-info/coccinelle/)
// <smpl>
@r exists@
local idexpression x;
statement S;
expression E;
identifier f,l;
position p1,p2;
expression *ptr != NULL;
@@
(
if ((x@p1 = \(kmalloc\|kzalloc\|kcalloc\)(...)) == NULL) S
|
x@p1 = \(kmalloc\|kzalloc\|kcalloc\)(...);
...
if (x == NULL) S
)
<... when != x
when != if (...) { <+...x...+> }
x->f = E
...>
(
return \(0\|<+...x...+>\|ptr\);
|
return@p2 ...;
)
@script:python@
p1 << r.p1;
p2 << r.p2;
@@
print "* file: %s kmalloc %s return %s" % (p1[0].file,p1[0].line,p2[0].line)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Unfortunately, the OF device tree nodes for SBUS and PCI
hme devices have the same device node name on some systems.
So if the name of the parent node isn't 'sbus', skip it.
Based upon an excellent report and detective work by
Meelis Roos and Eric Brower.
Signed-off-by: David S. Miller <davem@davemloft.net>
Tested-by: Meelis Roos <mroos@linux.ee>
|
|
When the changes were done to the protocol last release, some endian
bugs crept in. This patch fixes those endian problems and has been
verified to run on 32/64 bit and x86/ppc architectures.
This version of the patch incorporates the correct annotations
for endian variables.
Signed-off-by: Eric Van Hensbergen <ericvh@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Based upon a patch from Atsushi Nemoto <anemo@mba.ocn.ne.jp>
--------------------
The commit 649274d993212e7c23c0cb734572c2311c200872 ("net_dma:
acquire/release dma channels on ifup/ifdown") added unconditional call
of dmaengine_get() to net_dma. The API should be called only if
NET_DMA was enabled.
--------------------
Signed-off-by: David S. Miller <davem@davemloft.net>
Acked-by: Dan Williams <dan.j.williams@intel.com>
|
|
From: Ondrej Zary <linux@rainbow-software.org>
last year, I posted a patch which fixed hibernation on 3c509
cards. That was back in 2.6.24. It worked fine in 2.6.25. But then I
stopped using hibernation (as it did not work with my new IT8212 RAID
controller).
Now I fixed it and noticed that 3c509 does not wake up properly
anymore (in 2.6.28) - neither in PnP nor in ISA modes. ifconfig
down/up makes the card work again in PnP mode. However, in ISA mode,
ifconfig up ends with "No such device" error.
Comparing the 3c509 driver between 2.6.25 and 2.6.28, there's only
some statistics-related change. So the cause of the problem must be
somewhere else.
This patch makes the resume work in PnP mode, but it's still not
enough for ISA mode.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
From: Ilkka Virta <itvirta@iki.fi>
In the lockup situation the driver seems to go off in an eternal storm
of interrupts right after calling request_irq(). It doesn't actually
do anything interesting in the interrupt handler. Since connecting the link
afterwards works, something later in initialization must fix this.
Looking at gem_do_start() and gem_open(), it seems that the only thing
done while opening the device after the request_irq(), is a call to
napi_enable().
I don't know what the ordering requirements are for the
initialization, but I boldly tried to move the napi_enable() call
inside gem_do_start() before the link state is checked and interrupts
subsequently enabled, and it seems to work for me. Doesn't even break
anything too obvious...
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fix a potential NULL dereference bug during error handling in
rxrpc_kernel_begin_call(), whereby rxrpc_put_transport() may be handed a NULL
pointer.
This was found with a code checker (http://repo.or.cz/w/smatch.git/).
Reported-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Some Realtek chips (RTL8169sb/8110sb in my case) are unable to retrieve
ethtool statistics when the interface is down. The process stays in
endless loop in rtl8169_get_ethtool_stats. This is because these chips
need to have receiver enabled (CmdRxEnb bit in ChipCmd register) that is
cleared when the interface is going down. It's better to update statistics
only when the interface is up and otherwise return copy of statistics
grabbed when the interface was up (in rtl8169_close).
It is interesting that PCI-E NICs (like 8168b/8111b...) are not affected.
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Acked-by: Francois Romieu <romieu@fr.zoreil.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Like the UDP header fix, pskb_may_pull() can potentially
alter the SKB buffer. Thus the saddr and daddr, pointers
may point to the old skb->data buffer.
I haven't seen corruptions, as its only seen if the old
skb->data buffer were reallocated by another user and
written into very quickly (or poison'd by SLAB debugging).
Signed-off-by: Jesper Dangaard Brouer <hawk@comx.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
neightbl_dump_info and neigh_dump_table can skip entries if the
*fill*info functions return an error. This results in an incomplete
dump ((invoked by netlink requests for RTM_GETNEIGHTBL or
RTM_GETNEIGH)
nidx and idx should not be incremented if the current entry was not
placed in the output buffer
Signed-off-by: Gautam Kachroo <gk@aristanetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Just like PKTINFO, limit the options area to 64K.
Based upon report by Eric Sesterhenn and analysis by
Roland Dreier.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This reverts commit 64ff3b938ec6782e6585a83d5459b98b0c3f6eb8.
Jeff Chua reports that it breaks rlogin for him.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
As the options passed to ip6_append_data may be ephemeral, we need
to duplicate it for corking. This patch applies the simplest fix
which is to memdup all the relevant bits.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless-2.6
|
|
The UDP header pointer assignment must happen after calling
pskb_may_pull(). As pskb_may_pull() can potentially alter the SKB
buffer.
This was exposted by running multicast traffic through the NIU driver,
as it won't prepull the protocol headers into the linear area on
receive.
Signed-off-by: Jesper Dangaard Brouer <hawk@comx.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
SOFT_RESET must be asserted for at least 3 TX clocks in order for it to work
properly. The syncs in the gfar_write() commands have been hiding this, but
we need to guarantee it.
Signed-off-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|